ROUTER-OPT-MIB

File: ROUTER-OPT-MIB.mib (134611 bytes)

Imported modules

RFC1155-SMI RFC-1212

Imported symbols

IpAddress enterprises OBJECT-TYPE

Defined Types

MacAddress  
OCTET STRING Size(6)    

DisplayString  
OCTET STRING    

Cdx6500PCTRarpCacheEntry  
SEQUENCE    
  cdx6500PCTRarpCacheIndex INTEGER
  cdx6500PCTRarpCacheIfNum INTEGER
  cdx6500PCTRarpCacheProtocol INTEGER
  cdx6500PCTRarpCacheProtocolAd IpAddress
  cdx6500PCTRarpCacheMacAd MacAddress

Cdx6500PCTRaccControlEntry  
SEQUENCE    
  cdx6500PCTRaccControlIndex INTEGER
  cdx6500PCTRaccControlType INTEGER
  cdx6500PCTRaccControlSrcAd IpAddress
  cdx6500PCTRaccControlSrcMask IpAddress
  cdx6500PCTRaccControlDstAd IpAddress
  cdx6500PCTRaccControlDstMask IpAddress
  cdx6500PCTRaccControlFstProt INTEGER
  cdx6500PCTRaccControlLstProt INTEGER
  cdx6500PCTRaccControlFstPort INTEGER
  cdx6500PCTRaccControlLstPort INTEGER
  cdx6500PCTRaccControlSrcPort DisplayString
  cdx6500PCTRaccControlDstPort DisplayString
  cdx6500PCTRaccControlInIniface DisplayString
  cdx6500PCTRaccControlOutIniface DisplayString
  cdx6500PCTRaccControlInLcon DisplayString
  cdx6500PCTRaccControlOutLcon DisplayString

Cdx6500PCTRAcceptRIPRouteEntry  
SEQUENCE    
  cdx6500PCTRAcceptRIPRouteIndex INTEGER
  cdx6500PCTRAcceptRIPRouteIpNet IpAddress

Cdx6500PCTRifConfEntry  
SEQUENCE    
  cdx6500PCTRifConfIndex INTEGER
  cdx6500PCTRifConfIfNum INTEGER
  cdx6500PCTRifConfIpAd IpAddress
  cdx6500PCTRifConfAdMask IpAddress
  cdx6500PCTRifConfOvrDefRoute INTEGER
  cdx6500PCTRifConfOvrStatRoute INTEGER
  cdx6500PCTRifConfSndgDefRoute INTEGER
  cdx6500PCTRifConfSndgNetRoute INTEGER
  cdx6500PCTRifConfSndgSubRoute INTEGER
  cdx6500PCTRifConfSndgStatRoute INTEGER
  cdx6500PCTRifConfRcvgRipPkts INTEGER
  cdx6500PCTRifConfRcvgDynNets INTEGER
  cdx6500PCTRifConfRcvgDynSubs INTEGER
  cdx6500PCTRifConfTagAsNum INTEGER
  cdx6500PCTRifConfBcastStyle INTEGER
  cdx6500PCTRifConfBcastFill INTEGER
  cdx6500PCTRifMaxIpMTUSize INTEGER
  cdx6500PCTRifConfSplitHorizon INTEGER
  cdx6500PCTRifConfSr INTEGER
  cdx6500PCTRifRipMetric INTEGER
  cdx6500PCTRifSendRipVer DisplayString
  cdx6500PCTRifSendAggRoutes INTEGER
  cdx6500PCTRifAuthType INTEGER
  cdx6500PCTRifAuthKey DisplayString
  cdx6500PCTRifOnDemandRip INTEGER
  cdx6500PCTRifTrigUpdate INTEGER
  cdx6500PCTRifSecPrdBcastIntv INTEGER
  cdx6500PCTRifRoutInvldTime INTEGER
  cdx6500PCTRifRoutFlushTime INTEGER
  cdx6500PCTRifRdpEnable INTEGER
  cdx6500PCTRifRdpLevel DisplayString

Cdx6500PCTRbootpServEntry  
SEQUENCE    
  cdx6500PCTRbootpServIndex INTEGER
  cdx6500PCTRbootpServAd IpAddress

Cdx6500PCTRegpAsEntry  
SEQUENCE    
  cdx6500PCTRegpAsIndex INTEGER
  cdx6500PCTRegpAsNeighAs INTEGER
  cdx6500PCTRegpAsInterchFlag INTEGER
  cdx6500PCTRegpAsUseEgMetric INTEGER
  cdx6500PCTRegpAsDefMetric INTEGER

Cdx6500PCTRegpNeighEntry  
SEQUENCE    
  cdx6500PCTRegpNeighIndex INTEGER
  cdx6500PCTRegpNeighIdAd IpAddress
  cdx6500PCTRegpNeighAs INTEGER

Cdx6500PCTRdefSubGwayEntry  
SEQUENCE    
  cdx6500PCTRdefSubGwayIndex INTEGER
  cdx6500PCTRdefSubGwaySubnetAd IpAddress
  cdx6500PCTRdefSubGwayNextHopAd IpAddress
  cdx6500PCTRdefSubGwayDistToGway INTEGER

Cdx6500PCTRStaticRouteEntry  
SEQUENCE    
  cdx6500PCTRipRouteIndex INTEGER
  cdx6500PCTRipRouteIpNetwork IpAddress
  cdx6500PCTRipRouteIpMask IpAddress
  cdx6500PCTRipRouteNextHop IpAddress
  cdx6500PCTRipRouteCost INTEGER

Cdx6500PCTRoutInterchEntry  
SEQUENCE    
  cdx6500PCTRoutInterchIndex INTEGER
  cdx6500PCTRoutInterchInterchNeighAs INTEGER
  cdx6500PCTRoutInterchSourceAs INTEGER
  cdx6500PCTRoutInterchIpNetwork IpAddress
  cdx6500PCTRoutInterchUseIgpMetric INTEGER
  cdx6500PCTRoutInterchMetric INTEGER

Cdx6500PCTRinInterchEntry  
SEQUENCE    
  cdx6500PCTRinInterchIndex INTEGER
  cdx6500PCTRinInterchNeighAs INTEGER
  cdx6500PCTRinInterchIpNetwork IpAddress
  cdx6500PCTRinInterchUseEgpMetric INTEGER
  cdx6500PCTRinInterchMetric INTEGER

Cdx6500PCTRfilterEntry  
SEQUENCE    
  cdx6500PCTRfilterIndex INTEGER
  cdx6500PCTRfilterDstIpAd IpAddress
  cdx6500PCTRfilterAdMask IpAddress

Cdx6500PCTReventsEntry  
SEQUENCE    
  cdx6500PCTReventsIndex INTEGER
  cdx6500PCTReventsSubsystem INTEGER
  cdx6500PCTReventsPerPktTrace INTEGER
  cdx6500PCTReventsUnusualOper INTEGER
  cdx6500PCTReventsCommonOper INTEGER

Cdx6500PCTRifStateConfEntry  
SEQUENCE    
  cdx6500PCTRifStateConfIndex INTEGER
  cdx6500PCTRifStateConfState INTEGER

Cdx6500PCTRRIPRouteControlEntry  
SEQUENCE    
  cdx6500PCTRRIPRouteControlIndex INTEGER
  cdx6500PCTRRIPRouteControlIpNet IpAddress
  cdx6500PCTRRIPRouteControlIpMsk IpAddress
  cdx6500PCTRRRCInIniface DisplayString
  cdx6500PCTRRRCOutIniface DisplayString

Cdx6500PCTRtunnelEntry  
SEQUENCE    
  cdx6500PCTRtunnelIndex INTEGER
  cdx6500PCTRtunnelProt INTEGER
  cdx6500PCTRtunnelGreCksSqn DisplayString
  cdx6500PCTRtunnelGreResyncCntr INTEGER
  cdx6500PCTRtunnelSrcAddr IpAddress
  cdx6500PCTRtunnelDstAddr IpAddress
  cdx6500PCTRtunnelLconNo INTEGER
  cdx6500PCTRtunnelPayProt INTEGER
  cdx6500PCTRtunnelIfNo INTEGER
  cdx6500PCTRtunnelRtpHdrComProf DisplayString
  cdx6500PCTRtunnelBrdgLnkNo INTEGER
  cdx6500PCTRtunnelEncrProf DisplayString
  cdx6500PCTRtunnelDebug INTEGER

Cdx6500PSTRtunnelEntry  
SEQUENCE    
  cdx6500PSTRtunnelIndex INTEGER
  cdx6500PSTRtunnelIpPktIn INTEGER
  cdx6500PSTRtunnelIpPktOut INTEGER
  cdx6500PSTRtunnelIpPktDisc INTEGER
  cdx6500PSTRtunnelIpxPktIn INTEGER
  cdx6500PSTRtunnelIpxPktOut INTEGER
  cdx6500PSTRtunnelIpxPktDisc INTEGER
  cdx6500PSTRtunnelSrcAddr IpAddress
  cdx6500PSTRtunnelDstAddr IpAddress
  cdx6500PSTRtunnelPayProt INTEGER
  cdx6500PSTRtunnelEncrStatus DisplayString
  cdx6500PSTRtunnelRuihcStatus INTEGER
  cdx6500PSTRtunnelBrdgPktIn INTEGER
  cdx6500PSTRtunnelBrdgPktOut INTEGER
  cdx6500PSTRtunnelBrdgPktDisc INTEGER

Defined Values

codex 1.3.6.1.4.1.449
OBJECT IDENTIFIER    

cdxProductSpecific 1.3.6.1.4.1.449.2
OBJECT IDENTIFIER    

cdx6500 1.3.6.1.4.1.449.2.1
OBJECT IDENTIFIER    

cdx6500Configuration 1.3.6.1.4.1.449.2.1.2
OBJECT IDENTIFIER    

cdx6500CfgProtocolGroup 1.3.6.1.4.1.449.2.1.2.1
OBJECT IDENTIFIER    

cdx6500PCTRouterGroup 1.3.6.1.4.1.449.2.1.2.1.5
OBJECT IDENTIFIER    

cdx6500Statistics 1.3.6.1.4.1.449.2.1.3
OBJECT IDENTIFIER    

cdx6500StatProtocolGroup 1.3.6.1.4.1.449.2.1.3.1
OBJECT IDENTIFIER    

cdx6500PSTRouterGroup 1.3.6.1.4.1.449.2.1.3.1.4
OBJECT IDENTIFIER    

cdx6500Controls 1.3.6.1.4.1.449.2.1.4
OBJECT IDENTIFIER    

cdx6500PCTRarpCacheTable 1.3.6.1.4.1.449.2.1.2.1.5.1
ARP Cache Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRarpCacheEntry

cdx6500PCTRarpCacheEntry 1.3.6.1.4.1.449.2.1.2.1.5.1.1
A row of IP configurables
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRarpCacheEntry  

cdx6500PCTRarpCacheIndex 1.3.6.1.4.1.449.2.1.2.1.5.1.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRarpCacheIfNum 1.3.6.1.4.1.449.2.1.2.1.5.1.1.2
Interface Number. This must be a router Interface Number as assigned in the Interface Configuration Table (cdx6500PCTRifConfTable) entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..36  

cdx6500PCTRarpCacheProtocol 1.3.6.1.4.1.449.2.1.2.1.5.1.1.3
Protocol Type. This identifies one of the routing protocols supported by the router. newvalIp : same functionality as 'ip', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(0), ipx(7), appleTalk(22), newvalIp(50)  

cdx6500PCTRarpCacheProtocolAd 1.3.6.1.4.1.449.2.1.2.1.5.1.1.4
IP Address. The IP address of a particular host on the attached network identified by the Interface Number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRarpCacheMacAd 1.3.6.1.4.1.449.2.1.2.1.5.1.1.5
MAC Address.The hardware MAC address of the host with the IP Address of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

cdx6500PCTRarpParamAutoRef 1.3.6.1.4.1.449.2.1.2.1.5.2
Auto-Refresh. Enables/Disables the routers capacity to send an ARP request based on the entry in the translation cache before the refresh timer expires. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRarpParamRefTime 1.3.6.1.4.1.449.2.1.2.1.5.3
Refresh Timeout. Changes the timeout value (in minutes) for the refresh timer. A setting of 0 turns off (disables) the refresh timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRarpParamUseTime 1.3.6.1.4.1.449.2.1.2.1.5.4
Usage Timeout. Changes the timeout value (in minutes) for the usage timer. A setting of 0 turns off (disables) the usage timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRarpParamProxy 1.3.6.1.4.1.449.2.1.2.1.5.5
Proxy ARP. Enables the router to respond as proxy for hosts on different nets reachable from the router. Normal ARP operation calls for hosts to send an ARP request only for destinations that are on the same IP network (or subnetwork) as the requester. Some IP hosts, however, ARP even for off-network IP destination hosts. This parameter enables the router to respond as a proxy for such off-network hosts, causing the source to properly send off-network packets to the router. The router will respond only if the destination network/subnetwork is in its IP Routing Table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRarpParamProxySub 1.3.6.1.4.1.449.2.1.2.1.5.6
Proxy ARP Subnets Only. Enables the router to respond as a proxy for hosts on different subnets of the same top-level IP net as the ARP requester. This is a subset of the operation controlled with the Proxy ARP parameter. The router will respond only for a reachable destination subnet,i.e. one which is in its IP Routing Table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRaccControlTable 1.3.6.1.4.1.449.2.1.2.1.5.7
IP Access Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRaccControlEntry

cdx6500PCTRaccControlEntry 1.3.6.1.4.1.449.2.1.2.1.5.7.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRaccControlEntry  

cdx6500PCTRaccControlIndex 1.3.6.1.4.1.449.2.1.2.1.5.7.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRaccControlType 1.3.6.1.4.1.449.2.1.2.1.5.7.1.2
Access Type. Each received IP packet is compared with all Access Control list entries in order of Entry number. If the first matching Access Control Entry is include, the packet is forwarded. If the entry is exclude, the packet is dropped. If no matching entry is found, the packet is dropped. An entry matches a packet when the source IP address, destination IP address, IP Protocol number range and TCP/UDP port number range all match the packet. newvalExcluded : same functionality as 'excluded', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER excluded(0), included(1), newvalExcluded(50)  

cdx6500PCTRaccControlSrcAd 1.3.6.1.4.1.449.2.1.2.1.5.7.1.3
Source Address. IP source address to compare against a packet. An IP packet's source IP address field matches an Access Control entry when the result of logically AND-ing it with the Source Mask field equals the Source Address field. A Source Address field of 0.0.0.0 with a Source Mask field of 0.0.0.0 matches any source IP address in the packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRaccControlSrcMask 1.3.6.1.4.1.449.2.1.2.1.5.7.1.4
Address Mask. Address mask to be applied to a received source IP address. An address is logically AND-ed with the mask and compared with the Source Address. For example, a mask of 255.0.0.0 with a result of 129.0.0.0 will match any address with 129 in the first byte. A mask of 255.255.255.255 with a result of 129.122.3.26 matches only the IP host 129.122.3.26. A mask of 0.0.0.0 with a result of 0.0.0.0 is a wild card, and matches any IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRaccControlDstAd 1.3.6.1.4.1.449.2.1.2.1.5.7.1.5
Destination Address. IP destination address in dotted notation. An IP packet's destination IP address field matches an Access Control entry when the result of logically AND-ing it with the Destination Mask field equals the Destination Address field. A Destination Address field of 0.0.0.0 with a Destination Mask field of 0.0.0.0 matches any destination IP address in the packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRaccControlDstMask 1.3.6.1.4.1.449.2.1.2.1.5.7.1.6
Address Mask. Address mask in dotted notation to be applied to an IP packet's destination address. The packet destination IP address is logically AND-ed with the Destination Mask field and compared with the Destination Address field. For example, a mask of 255.0.0.0 with a result of 129.0.0.0 will match any address with 129 in the first byte. A mask of 255.255.255.255 with a result of 126.122.3.26 matches only the IP host 129.122.3.26. A mask of 0.0.0.0 with a result of 0.0.0.0 is a wild card, and matches any IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRaccControlFstProt 1.3.6.1.4.1.449.2.1.2.1.5.7.1.7
First Protocol. This decimal number corresponds to the protocol byte in the IP header. A packet with an IP protocol byte between the First Protocol value and Last Protocol value, inclusive, will match the entry. The First Protocol value must be less than or equal to the Last Protocol field value. A First Protocol of 0 and a Last Protocol of 255 will match all IP packets. Commonly used IP protocol numbers are 1 for ICMP, 6 for TCP, 8 for EGP, 17 for UDP and 89 for OSPF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

cdx6500PCTRaccControlLstProt 1.3.6.1.4.1.449.2.1.2.1.5.7.1.8
Last Protocol. This decimal number corresponds to the protocol byte in the IP header.A packet with a protocol value in the specified range will match. This parameter defines the upper value of this range, and must be greater than or equal to the First Protocol field value. A Protocol range of 0 to 255 will match all IP packets. Commonly used protocol numbers are 1 for ICMP, 6 for TCP, 8 for EGP, 17 for UDP and 89 for OSPF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

cdx6500PCTRaccControlFstPort 1.3.6.1.4.1.449.2.1.2.1.5.7.1.9
First Port. This decimal number corresponds to a UDP or TCP port number.A UDP or TCP packet will match an Access Control Entry when its UDP/TCP port number is at or above the entry's First Port value, and at or below the Last Port value. An entry with a First Port value of 0 and a Last Port value of 65535 will match all packets. Commonly used port numbers are 21 for FTP, 23 for Telnet, 25 for SMTP, 513 for rlogin, 520 for RIP, and 600 for X.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRaccControlLstPort 1.3.6.1.4.1.449.2.1.2.1.5.7.1.10
Last Port. This decimal number corresponds to a UDP or TCP port number. A UDP or TCP packet will match an Access Control Entry when its UDP/TCP port number is at or above the entry's First Port value, and at or below the Last Port value. An entry with a First Port value of 0 and a Last Port value of 65535 will match all packets. Commonly used port numbers are 21 for FTP, 23 for Telnet, 25 for SMTP, 513 for rlogin, 520 for RIP, and 600 for X.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRaccControlSrcPort 1.3.6.1.4.1.449.2.1.2.1.5.7.1.11
Source Port Range. This specifies the range (or set of ranges) of port numbers to which the packet's source socket number is compared. A range of 0-65535 will match all packets.A maximum of 8 ranges are permitted to be configured in this list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRaccControlDstPort 1.3.6.1.4.1.449.2.1.2.1.5.7.1.12
Destination Port Range. This specifies the range (or set of ranges) of port numbers to which the packet's destination socket number is compared. A range of 0-65535 will match all packets.A maximum of 8 ranges are permitted to be configured in this list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRaccControlInIniface 1.3.6.1.4.1.449.2.1.2.1.5.7.1.13
Inbound Interface List. This parameter specifies a list of interfaces. The filter is applied to packets received on these interfaces. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same flow definitions. Ex: 1,5,7-10,20-25,31 ALL : This option is a wildcard used to match all interfaces. NONE : This indicates that the filter action will not be applied on any interface. INT : This option is a wild card entry used to match internally generated traffic such as Ping, Telnet, SNMP, SOTCP. ALL-PLUS-INT : This option is a wild card entry used to match all interfaces and internally generated traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRaccControlOutIniface 1.3.6.1.4.1.449.2.1.2.1.5.7.1.14
Outbound Interface List. This parameter specifies a list of interfaces. The filter is applied to packets sent on these interfaces. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same flow definitions. Ex: 1,5,7-10,20-25,31 ALL : This option is a wildcard used to match all interfaces. NONE : This indicates that the filter action will not be applied on any interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRaccControlInLcon 1.3.6.1.4.1.449.2.1.2.1.5.7.1.15
Inbound LCON List. This parameter specifies a list of LCONS. The filter is applied to packets received on these LCONs. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same flow definitions. Ex: 1,5,7-10,20-25,31 ALL : This option is a wildcard used to match all LCONs. NONE : This indicates that the filter action will not be applied on any LCON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRaccControlOutLcon 1.3.6.1.4.1.449.2.1.2.1.5.7.1.16
Outbound LCON List. This parameter specifies a list of LCONS. The filter is applied to packets sent on these LCONs. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same flow definitions. Ex: 1,5,7-10,20-25,31 ALL : This option is a wildcard used to match all LCONs. NONE : This indicates that the filter action will not be applied on any LCON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRAcceptRIPRouteTable 1.3.6.1.4.1.449.2.1.2.1.5.8
IP Accept RIP Route Table. This table is now called Rip Route Control Table. Access RIP Route Control Table to get these values
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRAcceptRIPRouteEntry

cdx6500PCTRAcceptRIPRouteEntry 1.3.6.1.4.1.449.2.1.2.1.5.8.1
IP Accept RIP Route Table. This table is now called Rip Route Control Table. Access RIP Route Control Table to get these values
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRAcceptRIPRouteEntry  

cdx6500PCTRAcceptRIPRouteIndex 1.3.6.1.4.1.449.2.1.2.1.5.8.1.1
Table Index.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRAcceptRIPRouteIpNet 1.3.6.1.4.1.449.2.1.2.1.5.8.1.2
This parameter is now the part of Rip route control Table. IP Network/subnet. IP address which identifies a destination network or subnetwork for which RIP route information is accepted. The route is accepted from any received RIP packet, and overrides any disabled Learn Net Route or Learn Subnet Route setting.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRifConfTable 1.3.6.1.4.1.449.2.1.2.1.5.9
IP Interface Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRifConfEntry

cdx6500PCTRifConfEntry 1.3.6.1.4.1.449.2.1.2.1.5.9.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRifConfEntry  

cdx6500PCTRifConfIndex 1.3.6.1.4.1.449.2.1.2.1.5.9.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRifConfIfNum 1.3.6.1.4.1.449.2.1.2.1.5.9.1.2
Interface Number. Each interface must be assigned an Interface Number. Interface Numbers 1 through 4 are for the LAN ports. Interface numbers 5 through 36 are reserved for Lan Connections, which are virtual circuit links over WAN networks such as X.25 or Frame Relay to other routers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRifConfIpAd 1.3.6.1.4.1.449.2.1.2.1.5.9.1.3
IP Address. This parameter defines the 32-bit IP host address of the router on the associated interface. IP Addresses are considered to consist of a network part, a subnetwork part, and a host number. All IP routers and hosts on a LAN must be assigned the same network/subnetwork part for their IP address. The serial links (LAN connections) between routers must also be assigned an IP network/subnetwork number, and the IP Address assigned on both sides of a serial link must have the same network (and subnetwork) part.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRifConfAdMask 1.3.6.1.4.1.449.2.1.2.1.5.9.1.4
Address Mask. This parameter is entered in dotted notation and configures the 32-bit IP Subnetwork Address Mask associated with network to which the interfaces attaches. The subnetwork address mask has 1 bit for the bits which form the network and subnetwork portions of the IP address. For example, if the interface is on a class B network such as 128.185.0.0, and the third byte is used to select a subnet (e.g. 128.185.100.0), the mask should be set to 255.255.255.0. All IP devices on a subnetted network must be configured with the same subnetwork address mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRifConfOvrDefRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.5
Override Default Route.Enables the router to override the configured Default Gateway when it receives a RIP update from another router advertising the default route of 0.0.0.0 with a cheaper metric than the configured Default Gateway Metric. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfOvrStatRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.6
Override Static Route. Enables/Disables the receipt of RIP information on this interface to override the router's statically configured routing information, providing the cost of the RIP information is cheaper. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfSndgDefRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.7
Advertise Default Route. Enables/Disables this router advertising the default route of 0.0.0.0 on this interface. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfSndgNetRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.8
Advertise Network Routes. Enables/Disables advertisement of directly-attached networks and learned IP network routes on RIP updates transmitted on this interface. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfSndgSubRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.9
Advertise Subnet Routes. Enables/Disables the inclusion of all subnet routes within RIP updates sent on this interface. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfSndgStatRoute 1.3.6.1.4.1.449.2.1.2.1.5.9.1.10
Advertise Static/Direct Routes. Enables/Disables the inclusion of all statically configured and directly connected routes within RIP updates sent on this interface. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfRcvgRipPkts 1.3.6.1.4.1.449.2.1.2.1.5.9.1.11
Accept RIP. Enables/Disables the processing of RIP updates received on this interface. This is normally enabled whenever RIP is enabled. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfRcvgDynNets 1.3.6.1.4.1.449.2.1.2.1.5.9.1.12
Learn Network Routes. Enables/Disables the learning of new network-level routes received from neighboring routers on this interface's network. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfRcvgDynSubs 1.3.6.1.4.1.449.2.1.2.1.5.9.1.13
Learn Subnet Routes. Enables/Disables the learning of new subnet-level routes received from neighboring routers on this interface's network. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfTagAsNum 1.3.6.1.4.1.449.2.1.2.1.5.9.1.14
AS Number. Specifies a tag to be associated with RIP information received on this interface. Tags are used to group routes together for later readvertisement via EGP, where the tag is treated as if it were a route's source Autonomous System. Tags are also propagated by the OSPF routing protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRifConfBcastStyle 1.3.6.1.4.1.449.2.1.2.1.5.9.1.15
Broadcast Style. Specifies the convention for addressing IP broadcasts to all other hosts on the attached network. LOCAL broadcast style means that the Broadcast Fill Pattern (1s or 0s) fills all 32 bits of the IP broadcast address. NET broadcast style means that the Network and subnetwork portion of the IP broadcast address is set to the interface's network number, and the Broadcast Fill pattern fills only the host portion. Examples: LOCAL 1-fill: 255.255.255.255 LOCAL 0-fill: 0.0.0.0 NET 1-fill: 128.185.255.255 NET 0-fill: 128.185.0.0 All IP devices on a network must be configured with the same IP broadcast address convention. newvalNetwork : same functionality as 'network', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER network(0), local(1), newvalNetwork(50)  

cdx6500PCTRifConfBcastFill 1.3.6.1.4.1.449.2.1.2.1.5.9.1.16
Broadcast Fill Pattern. Specifies the IP broadcast fill pattern the router will use when broadcasting on this interface. See Broadcast Style, cdx6500PCTRifConfBcastStyle.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

cdx6500PCTRifMaxIpMTUSize 1.3.6.1.4.1.449.2.1.2.1.5.9.1.17
Specifies the Maximum Transmission Unit to be used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 576..65535  

cdx6500PCTRifConfSplitHorizon 1.3.6.1.4.1.449.2.1.2.1.5.9.1.18
This parameter enables/disables the IP RIP split horizon. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifConfSr 1.3.6.1.4.1.449.2.1.2.1.5.9.1.19
This parameter enables/disables the IP use of a RIF field in Token Ring networks for ARPs and RIPs. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRifRipMetric 1.3.6.1.4.1.449.2.1.2.1.5.9.1.20
The cost,in number of hops to receive a packet through this interface. This is the cost of direct route in this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

cdx6500PCTRifSendRipVer 1.3.6.1.4.1.449.2.1.2.1.5.9.1.21
Send RIP Version. VER1 - send RIP Version 1 updates, VER2-B - send RIP Version 2 updates as broadcast, VER2-M - send RIP Version 2 updates as multicast.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..20)  

cdx6500PCTRifSendAggRoutes 1.3.6.1.4.1.449.2.1.2.1.5.9.1.22
When disabled, this parameter indicates that when sending routes to this interface, aggregated routing information is converted into non aggregated routing information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRifAuthType 1.3.6.1.4.1.449.2.1.2.1.5.9.1.23
This defines the type of authenticaton to be used for RIPv2 Packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), simple(2)  

cdx6500PCTRifAuthKey 1.3.6.1.4.1.449.2.1.2.1.5.9.1.24
This is the Authentication key sent in the RIP packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

cdx6500PCTRifOnDemandRip 1.3.6.1.4.1.449.2.1.2.1.5.9.1.25
Enable : Enables on demand RIP for the interface Disable : Disables on demand RIP for the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRifTrigUpdate 1.3.6.1.4.1.449.2.1.2.1.5.9.1.26
None : No triggered updates will be sent Changes : Triggered updates will be sent with only the changed routing table entries. Full : Triggered updates will be sent with all the entries in the routing table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), change(2), full(3)  

cdx6500PCTRifSecPrdBcastIntv 1.3.6.1.4.1.449.2.1.2.1.5.9.1.27
Full RIP updates will be sent periodically with the time interval configured in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 6..65529  

cdx6500PCTRifRoutInvldTime 1.3.6.1.4.1.449.2.1.2.1.5.9.1.28
Specifies time in sec after which the route will be marked unreachable.The time interval should be a multiple of 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..65530  

cdx6500PCTRifRoutFlushTime 1.3.6.1.4.1.449.2.1.2.1.5.9.1.29
Specifies time in sec after which the route will be deleted from the routing table.The time interval should be a multiple of 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..65530  

cdx6500PCTRifRdpEnable 1.3.6.1.4.1.449.2.1.2.1.5.9.1.30
Enables/Disables the advertising of this interface's address for Router Discovery (RFC 1256).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRifRdpLevel 1.3.6.1.4.1.449.2.1.2.1.5.9.1.31
Specifies the preferability of this interface's address as the default router address on the interface's subnet. Range : 0 - 0xffffffff.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

cdx6500PCTRbootpServTable 1.3.6.1.4.1.449.2.1.2.1.5.10
IP BOOTP Server Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRbootpServEntry

cdx6500PCTRbootpServEntry 1.3.6.1.4.1.449.2.1.2.1.5.10.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRbootpServEntry  

cdx6500PCTRbootpServIndex 1.3.6.1.4.1.449.2.1.2.1.5.10.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRbootpServAd 1.3.6.1.4.1.449.2.1.2.1.5.10.1.2
BOOTP Server Address. Adds a BootP server IP address (in dotted notation) to the routers configuration (the router will forward BootP requests to the specified BootP server). This must be used in conjunction with the BootP Forwarding command under the IP Parameters menu. There are no defaults for this command and valid address must be entered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRegpAsTable 1.3.6.1.4.1.449.2.1.2.1.5.11
IP EGP AS Information Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRegpAsEntry

cdx6500PCTRegpAsEntry 1.3.6.1.4.1.449.2.1.2.1.5.11.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRegpAsEntry  

cdx6500PCTRegpAsIndex 1.3.6.1.4.1.449.2.1.2.1.5.11.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRegpAsNeighAs 1.3.6.1.4.1.449.2.1.2.1.5.11.1.2
Neighboring AS. The number of the Autonomous System to which routing information wil be exchanged. For a value of 0, the default EGP exchange is defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRegpAsInterchFlag 1.3.6.1.4.1.449.2.1.2.1.5.11.1.3
Interchange Flag. Defines the permissible exchange of EGP route information. IN causes all routes received from the neighboring AS to be readvertised via OSPF and RIP. OUT causes all internal known routes to be advertised to EGP. OFF indicates the particular IP networks to be re-advertised are controlled with the Output-Interchange and Input-Interchange configurations. OFF is the recommended configuration. newvalOff : same functionality as 'off', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), newvalOff(50)  

cdx6500PCTRegpAsUseEgMetric 1.3.6.1.4.1.449.2.1.2.1.5.11.1.4
Use EGP Metric. This parameter is ON or OFF. When ON, the re-advertised cost is the same as the originally learned cost. For IN interchanges, the EGP cost metric is reported as the RIP/OSPF cost. For OUT interchanges, the RIP/OSPF cost metric is reported as the EGP cost. If this parameter is OFF, the Default Metric parameter of this record is always reported as the cost. newvalOff : same functionality as 'off', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), newvalOff(50)  

cdx6500PCTRegpAsDefMetric 1.3.6.1.4.1.449.2.1.2.1.5.11.1.5
Default Metric. The default cost used for readvertisements. This is usually interpreted as a number of hops. For IN interchanges, this means all routes will be readvertised by OSPF and RIP with the Default Metric cost. In the OUT direction, this means all routes in the RIP/OSPF routing table will be advertised to EGP with the given cost.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRegpNeighTable 1.3.6.1.4.1.449.2.1.2.1.5.12
IP EGP Neighbor Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRegpNeighEntry

cdx6500PCTRegpNeighEntry 1.3.6.1.4.1.449.2.1.2.1.5.12.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRegpNeighEntry  

cdx6500PCTRegpNeighIndex 1.3.6.1.4.1.449.2.1.2.1.5.12.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRegpNeighIdAd 1.3.6.1.4.1.449.2.1.2.1.5.12.1.2
Neighbor IP Address. IP address of an EGP neighbor in dotted notation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRegpNeighAs 1.3.6.1.4.1.449.2.1.2.1.5.12.1.3
Neighboring AS. Autonomous System number of the EGP neighbor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

cdx6500PCTRipParamBootpFwdg 1.3.6.1.4.1.449.2.1.2.1.5.13
BOOTP Forwarding. Enables/Disables the forwarding of BootP requests. BOOTP (Boot Parameters) is a protocol that allows workstations to obtain their startup operating system software and other parameters from a BOOTP Server host on the IP network. If enabled, the location of the BOOTP servers must be configured in the cdx6500PCTRbootpServTable MIB table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRipParamBootpMaxHops 1.3.6.1.4.1.449.2.1.2.1.5.14
BOOTP Max Allowed Metric. The maximum cost metric (hop count) a BootP request is allowed to attain before being discarded. This is NOT the maximum number of IP hops to the BootP server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRipParamBootpSbf 1.3.6.1.4.1.449.2.1.2.1.5.15
BOOTP Seconds Before Forward. The number of seconds the router will wait for a BOOT request to be repeated before forwarding the request to BOOTP Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRipParamEgpSysNum 1.3.6.1.4.1.449.2.1.2.1.5.16
EGP System Number. Configures the router's Autonomous System Number, as assigned by the Internet Network Information Center. The Exterior Gateway Protocol (EGP) is used to communicate with the Internet backbone. Usually, all of the routers for one company are considered in a single Autonomous System (AS), and all must have the same EGP Autonomous system number. EGP is used by the one (or two, for backup) of a company's gateway routers that connect to an administered Internet backbone such as Milnet or NSFnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

cdx6500PCTRipParamEgpReadvert 1.3.6.1.4.1.449.2.1.2.1.5.17
EGP Readvertise. Globally Enables/Disables the readvertisement of EGP routes which were originally learned from EGP. When Enabled, the learned routes are advertised locally with RIP or OSPF. The particular EGP neighbors from which routes are learned are specified with the cdx6500PCTRegpAsTable table. The particular networks which are learned can be specified with the cdx6500PCTRinInterchTable table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRipParamRip 1.3.6.1.4.1.449.2.1.2.1.5.18
RIP Enable. Globally Enables/Disables RIP protocol processing for the router. The Routing Information Protocol (RIP) was the original internal gateway routing protocol used for IP networks, and is suitable for moderate size organization networks. An organization may operate both RIP and OSPF simultaneously. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRipParamRipOrigDef 1.3.6.1.4.1.449.2.1.2.1.5.19
Originate Default Route. Enables origination and RIP advertisement of the default IP route 0.0.0.0. Default route advertisements must also be explicitly enabled for each interface. The router will originate the default route only when it has EGP-derived or external OSPF routes in its routing table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRipParamAdvDefMetCost 1.3.6.1.4.1.449.2.1.2.1.5.20
Advertised Default Metric Cost. Sets the cost metric (usually the number of hops) that RIP will advertise for the default route of 0.0.0.0. A metric of 16 advertises that the default route is unreachable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

cdx6500PCTRipParamNextHopDefGway 1.3.6.1.4.1.449.2.1.2.1.5.21
Default Gateway. The IP address of the default gateway -this- router will use when a packet's destination route is otherwise unknown. The next hop must be to a router on a directly attached network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipParamDistDefGway 1.3.6.1.4.1.449.2.1.2.1.5.22
Default Gateway Metric. The cost metric for a transmission to this router's default gateway, usually given as the number of network hops.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRipParamRoutTableSize 1.3.6.1.4.1.449.2.1.2.1.5.23
Routing Table Size. The maximum number of routes that may be stored in the IP routing table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 64..65535  

cdx6500PCTRipParamDirBcast 1.3.6.1.4.1.449.2.1.2.1.5.24
Directed Broadcast. Enables/Disables the forwarding of IP packets whose destination is a non-local (remote LAN) broadcast address. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRipParamInternalNetMask 1.3.6.1.4.1.449.2.1.2.1.5.25
This parameter is entered in dotted notation and configures the 32-bit IP Subnetwork Address Mask associated with the Internal interface created when the Internal Address is added to the router configuration parameters. The Internal Network address is derived from the configured Internal address and Internal Network Mask parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipParamInternalIpAd 1.3.6.1.4.1.449.2.1.2.1.5.26
This is an IP Address that becomes the Default IP Address for the router. The Default IP Address is used as the IP source address of PING and ICMP frames originated from the router to unnumbered interfaces and it is the reported IP Address in SNMP Trap frames. A Internal Network is added to the router routing table with the network address derived from the configured Internal address and Internal Network Mask parameter. If Internal IP Address is left undefined or the network part of this address matches network address of the configured router interfaces, Default IP Address becomes the IP address of the lowest numbered operational interface of the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipParamCacheSize 1.3.6.1.4.1.449.2.1.2.1.5.27
IP Route Cache Size. The maximum number of entries that may be stored in the IP Route cache. The IP Route Cache holds the destination addresses of recently received packets and for each entry maintains a count of packets forwarded to that destination.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 64..10000  

cdx6500PCTRipParamReasmBuffSize 1.3.6.1.4.1.449.2.1.2.1.5.28
Reassembly Buffer Size. Sets the size (in bytes) of the IP fragment reassembly buffers. It must be set greater than the size of the largest IP packet to be transmitted on the organization's network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2048..65535  

cdx6500PCTRipParamAccessCntrl 1.3.6.1.4.1.449.2.1.2.1.5.29
Access Control. Globally enables or disables operation of the IP Access Control table. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRdefSubGwayTable 1.3.6.1.4.1.449.2.1.2.1.5.30
IP Default Subnet Gateway Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRdefSubGwayEntry

cdx6500PCTRdefSubGwayEntry 1.3.6.1.4.1.449.2.1.2.1.5.30.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRdefSubGwayEntry  

cdx6500PCTRdefSubGwayIndex 1.3.6.1.4.1.449.2.1.2.1.5.30.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRdefSubGwaySubnetAd 1.3.6.1.4.1.449.2.1.2.1.5.30.1.2
Top-Level IP Address. The top-level IP network number must be a class A, B, or C IP address. If this router receives a packet destined to an unknown subnet of that top level net, it will forward the packet to the default subnet router for that net.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRdefSubGwayNextHopAd 1.3.6.1.4.1.449.2.1.2.1.5.30.1.3
Next Hop to Subnet Gateway. The IP address of the next hop towards a router performing subnet routing for the top-level net of this record. This next hop must be to an IP address on a network directly connected to this router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRdefSubGwayDistToGway 1.3.6.1.4.1.449.2.1.2.1.5.30.1.4
Metric to Subnet Gateway. The cost metric for a transmission to the default subnet gateway, usually the number of network hops to reach that other router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRStaticRouteTable 1.3.6.1.4.1.449.2.1.2.1.5.31
IP Route Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRStaticRouteEntry

cdx6500PCTRStaticRouteEntry 1.3.6.1.4.1.449.2.1.2.1.5.31.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRStaticRouteEntry  

cdx6500PCTRipRouteIndex 1.3.6.1.4.1.449.2.1.2.1.5.31.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRipRouteIpNetwork 1.3.6.1.4.1.449.2.1.2.1.5.31.1.2
IP Network/Subnet. The IP address of a destination network or subnetwork Host addresses are not included in the route table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipRouteIpMask 1.3.6.1.4.1.449.2.1.2.1.5.31.1.3
IP Address Mask. The mask associated with the IP Network/Subnet address. For example: if the destination is a subnet of a class B network and the third byte of the IP address is used as the subnet portion, the address mask would be set to 255.255.255.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipRouteNextHop 1.3.6.1.4.1.449.2.1.2.1.5.31.1.4
Next Hop. The IP address of the next hop to the destination. The next hop itself must be on an IP network directly connected to the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRipRouteCost 1.3.6.1.4.1.449.2.1.2.1.5.31.1.5
Cost. The distance or cost metric to the destination. It is interpreted as a number of hops.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRoutInterchTable 1.3.6.1.4.1.449.2.1.2.1.5.32
IP Output Interchange Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRoutInterchEntry

cdx6500PCTRoutInterchEntry 1.3.6.1.4.1.449.2.1.2.1.5.32.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRoutInterchEntry  

cdx6500PCTRoutInterchIndex 1.3.6.1.4.1.449.2.1.2.1.5.32.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRoutInterchInterchNeighAs 1.3.6.1.4.1.449.2.1.2.1.5.32.1.2
Neighboring AS. The AS number assigned to an EGP neighbor. If nonzero, the value must match a Neighboring AS number entered in a IP EGP AS Information Table, cdx6500PCTRegpAsTable, entry. A value of 0 adds the route to the default Output Exchange Table, which is reported to all new EGP neighbors learned and not otherwise entered in the IP EGP AS Information table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRoutInterchSourceAs 1.3.6.1.4.1.449.2.1.2.1.5.32.1.3
Source AS. A value of 0 indicates the route should be advertised regardless of the Autonomous System it was received from. A value other than 0 indicates the route should only be advertised if the route was received from the specified AS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRoutInterchIpNetwork 1.3.6.1.4.1.449.2.1.2.1.5.32.1.4
IP Network. The address of the local IP network for which routing information will be advertised.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRoutInterchUseIgpMetric 1.3.6.1.4.1.449.2.1.2.1.5.32.1.5
Use IGP Metric. This parameter and the following Metric parameter, cdx6500PCTRoutInterchMetric, determine the cost reported to EGP of accessing the internal IP network. The two possible Interior Gateway Protocols (IGPs) are RIP or OSPF. If Use IGP metric is ON, the cost advertised to EGP will be identical to the locally reported routing table cost (from RIP or OSPF). If Use IGP metric OFF, the Metric parameter of this entry is reported. newvalOff : same functionality as 'off', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), newvalOff(50)  

cdx6500PCTRoutInterchMetric 1.3.6.1.4.1.449.2.1.2.1.5.32.1.6
Metric. A configured cost of the route to the interior network, interpreted as a hop count. This cost is reported to EGP if the the Use IGP metric parameter, cdx6500PCTRoutInterchUseIgpMetric, is OFF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRinInterchTable 1.3.6.1.4.1.449.2.1.2.1.5.33
IP Input Interchange Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRinInterchEntry

cdx6500PCTRinInterchEntry 1.3.6.1.4.1.449.2.1.2.1.5.33.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRinInterchEntry  

cdx6500PCTRinInterchIndex 1.3.6.1.4.1.449.2.1.2.1.5.33.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRinInterchNeighAs 1.3.6.1.4.1.449.2.1.2.1.5.33.1.2
Neighboring AS. A neighboring Autonomous System to which route information will be readvertised via OSPF and RIP. A value of 0 adds the route to the default Input Exchange Table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

cdx6500PCTRinInterchIpNetwork 1.3.6.1.4.1.449.2.1.2.1.5.33.1.3
IP Network. The IP address of a network for which EGP received routing information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRinInterchUseEgpMetric 1.3.6.1.4.1.449.2.1.2.1.5.33.1.4
Use EGP Metric. Defines the source of the internally readvertised costs of reaching the external IP network for this entry. If ON, the readvertised cost will be identical to the cost received by the EGP protocol. If OFF, the Metric parameter of this entry is reported. newvalOff : same functionality as 'off', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), newvalOff(50)  

cdx6500PCTRinInterchMetric 1.3.6.1.4.1.449.2.1.2.1.5.33.1.5
Metric. A configured cost of the route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRfilterTable 1.3.6.1.4.1.449.2.1.2.1.5.34
IP Filter Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRfilterEntry

cdx6500PCTRfilterEntry 1.3.6.1.4.1.449.2.1.2.1.5.34.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRfilterEntry  

cdx6500PCTRfilterIndex 1.3.6.1.4.1.449.2.1.2.1.5.34.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRfilterDstIpAd 1.3.6.1.4.1.449.2.1.2.1.5.34.1.2
Destination IP Address. IP address of a network/subnet to filter. All packets destined for a filtered network are discarded, and no route to the filtered network is advertised.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRfilterAdMask 1.3.6.1.4.1.449.2.1.2.1.5.34.1.3
Address Mask. Network (or Subnetwork) Address mask associated with the network/subnet address to filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRifState1 1.3.6.1.4.1.449.2.1.2.1.5.35
Interface #1 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState2 1.3.6.1.4.1.449.2.1.2.1.5.36
Interface #2 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState3 1.3.6.1.4.1.449.2.1.2.1.5.37
Interface #3 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState4 1.3.6.1.4.1.449.2.1.2.1.5.38
Interface #4 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState5 1.3.6.1.4.1.449.2.1.2.1.5.39
Interface #5 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState6 1.3.6.1.4.1.449.2.1.2.1.5.40
Interface #6 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState7 1.3.6.1.4.1.449.2.1.2.1.5.41
Interface #7 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState8 1.3.6.1.4.1.449.2.1.2.1.5.42
Interface #8 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState9 1.3.6.1.4.1.449.2.1.2.1.5.43
Interface #9 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState10 1.3.6.1.4.1.449.2.1.2.1.5.44
Interface #10 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState11 1.3.6.1.4.1.449.2.1.2.1.5.45
Interface #11 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState12 1.3.6.1.4.1.449.2.1.2.1.5.46
Interface #12 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState13 1.3.6.1.4.1.449.2.1.2.1.5.47
Interface #13 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState14 1.3.6.1.4.1.449.2.1.2.1.5.48
Interface #14 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState15 1.3.6.1.4.1.449.2.1.2.1.5.49
Interface #15 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState16 1.3.6.1.4.1.449.2.1.2.1.5.50
Interface #16 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState17 1.3.6.1.4.1.449.2.1.2.1.5.51
Interface #17 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState18 1.3.6.1.4.1.449.2.1.2.1.5.52
Interface #18 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState19 1.3.6.1.4.1.449.2.1.2.1.5.53
Interface #19 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState20 1.3.6.1.4.1.449.2.1.2.1.5.54
Interface #20 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState21 1.3.6.1.4.1.449.2.1.2.1.5.55
Interface #21 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState22 1.3.6.1.4.1.449.2.1.2.1.5.56
Interface #22 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState23 1.3.6.1.4.1.449.2.1.2.1.5.57
Interface #23 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState24 1.3.6.1.4.1.449.2.1.2.1.5.58
Interface #24 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState25 1.3.6.1.4.1.449.2.1.2.1.5.59
Interface #25 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState26 1.3.6.1.4.1.449.2.1.2.1.5.60
Interface #26 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState27 1.3.6.1.4.1.449.2.1.2.1.5.61
Interface #27 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState28 1.3.6.1.4.1.449.2.1.2.1.5.62
Interface #28 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState29 1.3.6.1.4.1.449.2.1.2.1.5.63
Interface #29 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState30 1.3.6.1.4.1.449.2.1.2.1.5.64
Interface #30 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState31 1.3.6.1.4.1.449.2.1.2.1.5.65
Interface #31 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState32 1.3.6.1.4.1.449.2.1.2.1.5.66
Interface #32 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState33 1.3.6.1.4.1.449.2.1.2.1.5.67
Interface #33 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState34 1.3.6.1.4.1.449.2.1.2.1.5.68
Interface #34 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState35 1.3.6.1.4.1.449.2.1.2.1.5.69
Interface #35 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRifState36 1.3.6.1.4.1.449.2.1.2.1.5.70
Interface #36 State. Enable/Disable all routing operations on the interface associated with this interface number. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTReventsTable 1.3.6.1.4.1.449.2.1.2.1.5.71
IP Events Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTReventsEntry

cdx6500PCTReventsEntry 1.3.6.1.4.1.449.2.1.2.1.5.71.1
A row of IP configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTReventsEntry  

cdx6500PCTReventsIndex 1.3.6.1.4.1.449.2.1.2.1.5.71.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

cdx6500PCTReventsSubsystem 1.3.6.1.4.1.449.2.1.2.1.5.71.1.2
Protocol. This field selects one of the protocols supported by the router. The event messages are controlled on a per-protocol basis. newvalArp : same functionality as 'arp', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER arp(0), ip(1), icmp(2), udp(3), rip(4), egp(5), ospf(6), ipx(7), tkr(8), eth(9), newvalArp(50)  

cdx6500PCTReventsPerPktTrace 1.3.6.1.4.1.449.2.1.2.1.5.71.1.3
Per Packet Trace. If enabled, reports an event for every packet processed by the subsytem. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTReventsUnusualOper 1.3.6.1.4.1.449.2.1.2.1.5.71.1.4
Unusual Operation. Enables/Disables reporting of unusual conditions such as detected packet format errors. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTReventsCommonOper 1.3.6.1.4.1.449.2.1.2.1.5.71.1.5
Common Operation. Enables/Disables reporting of commonly occurring events, such as receiving a RIP or OSPF update packet. newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), newvalDisabled(50)  

cdx6500PCTRpriorityIpTraffic 1.3.6.1.4.1.449.2.1.2.1.5.72
IP Traffic Priority. Defines the priority for IP traffic relative to the rest of the traffic transmitted over WAN virtual circuits. If not configured, a default priority of HIGH is used. newvalLow : same functionality as 'low', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), newvalLow(50)  

cdx6500PCTRpriorityIpxTraffic 1.3.6.1.4.1.449.2.1.2.1.5.73
IPX Traffic Priority. Defines the priority for IPX traffic relative to the rest of the traffic transmitted over WAN virtual circuits. If not configured, a default priority of HIGH is used. newvalLow : same functionality as 'low', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER low(0), medium(1), high(2), newvalLow(50)  

cdx6500PCTRMaxIpInterfaces 1.3.6.1.4.1.449.2.1.2.1.5.74
Specifies the maximum number of IP Interfaces that may be configured
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

cdx6500PCTRAllSubnetBrcast 1.3.6.1.4.1.449.2.1.2.1.5.75
Enables/Disables the duplication and forwarding of IP packets which are destined for all hosts on all subnetworks of an IP network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRIpFwdEnable 1.3.6.1.4.1.449.2.1.2.1.5.76
Enables/Disables the IP Broadcast Forwarding Feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRUdpFwdEnable 1.3.6.1.4.1.449.2.1.2.1.5.77
Enables/Disables the UDP Broadcast Forwarding Feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cdx6500PCTRpriorityAp2Traffic 1.3.6.1.4.1.449.2.1.2.1.5.78
AppleTalk Traffic Priority. Defines the priority for AppleTalk traffic relative to the rest of the traffic transmitted over WAN virtual circuits. If not configured, a default priority of HIGH is used. newvalLow : same functionality as 'low', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER low(1), medium(2), high(3)  

cdx6500PCTRarpParamMaxQueue 1.3.6.1.4.1.449.2.1.2.1.5.79
Specifies the maximum Protocol packets which can be queued awaiting address resolution.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..50  

cdx6500PCTRarpParamTimeRetx 1.3.6.1.4.1.449.2.1.2.1.5.80
Time(in seconds) to resend an ARP Request for a protocol address awaiting resolution.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

cdx6500PCTRRIPRouteControlTable 1.3.6.1.4.1.449.2.1.2.1.5.81
IP RIP Route Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRRIPRouteControlEntry

cdx6500PCTRifStateConfTable 1.3.6.1.4.1.449.2.1.2.1.5.83
IP Interfaces States Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRifStateConfEntry

cdx6500PCTRifStateConfEntry 1.3.6.1.4.1.449.2.1.2.1.5.83.1
A row of IP Interfaces States configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRifStateConfEntry  

cdx6500PCTRifStateConfIndex 1.3.6.1.4.1.449.2.1.2.1.5.83.1.1
Table Index (Corresponds to Interface Number Configured). Note: If Index N is not shown, it means Interface Number N State record is not present in the cmem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

cdx6500PCTRifStateConfState 1.3.6.1.4.1.449.2.1.2.1.5.83.1.2
Interfaces State. Enable/Disable all routing operations on the interface associated with this interface number. (The interface number is the cdx6500PCTRifStateConfIndex) newvalDisabled : same functionality as 'disabled', new enumeration added for RFC1155 compatibility.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), unconfigured(2), newvalDisabled(50)  

cdx6500PCTRRIPRouteControlEntry 1.3.6.1.4.1.449.2.1.2.1.5.81.1
IP RIP Route Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRRIPRouteControlEntry  

cdx6500PCTRRIPRouteControlIndex 1.3.6.1.4.1.449.2.1.2.1.5.81.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

cdx6500PCTRRIPRouteControlIpNet 1.3.6.1.4.1.449.2.1.2.1.5.81.1.2
IP Network/subnet. IP address which identifies a destination network or subnetwork for which RIP route information is accepted. The route is accepted from any received RIP packet, and overrides any disabled Learn Net Route or Learn Subnet Route setting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRRIPRouteControlIpMsk 1.3.6.1.4.1.449.2.1.2.1.5.81.1.3
IP Address Mask. Adress mask to be applied to the IP network/subnetwork address. The incoming route's IP address is logically 'AND-ed' with it's mask and the result is comparedwith the result of the logical 'ANDing' of the configured IP address and mask. For example, a mask of 255.0.0.0 with a result of 129.0.0.0 will match any route with 129 in the first byte. A mask of 0.0.0.0 indicates that this parameter will not be used. This parameter will only be used for RIPv2 routes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRRRCInIniface 1.3.6.1.4.1.449.2.1.2.1.5.81.1.4
Inbound interface list. This parameter specifies a list of interfaces on which the RIP route information is accepted. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same IP network/subnet address. Ex: 1, 5, 7-10, 20-25,31 ALL : This option is a wildcard used to match all interfaces. NONE : This indicates that no inbound RIP route control is required for this IP network/subnetwork address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

cdx6500PCTRRRCOutIniface 1.3.6.1.4.1.449.2.1.2.1.5.81.1.5
Outbound interface list. This parameter specifies a list of interfaces on which the RIP route information is advertised. A maximum of 8 ranges are permitted to be configured in this list : the list may be extended by configuring new entries with the same IP network/subnet address. Ex: 1, 5, 7-10, 20-25,31 ALL : This option is a wildcard used to match all interfaces. NONE : This indicates that no inbound RIP route control is required for this IP network/subnetwork address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

proProtoIpDefGwAddress 1.3.6.1.4.1.449.2.1.3.1.4.1
The Internet address of the default gateway for the router.
Status: optional Access: read-only
OBJECT-TYPE    
  IpAddress  

proProtoIpDefGwCost 1.3.6.1.4.1.449.2.1.3.1.4.2
The cost of the default gateway for the router.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

proProtoIpDefGwAge 1.3.6.1.4.1.449.2.1.3.1.4.3
The age of the default gateway for the router.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PCTRtunnelTable 1.3.6.1.4.1.449.2.1.2.1.5.82
Tunnel Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PCTRtunnelEntry

cdx6500PCTRtunnelEntry 1.3.6.1.4.1.449.2.1.2.1.5.82.1
Tunnel configurables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PCTRtunnelEntry  

cdx6500PCTRtunnelIndex 1.3.6.1.4.1.449.2.1.2.1.5.82.1.1
Table Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PCTRtunnelDstAddr 1.3.6.1.4.1.449.2.1.2.1.5.82.1.6
Destination Address.This is the destination address of the tunnel. This address is put into the destination field of the tunnel packet. This field cannot be 0.0.0.0 or un-numbered address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRtunnelSrcAddr 1.3.6.1.4.1.449.2.1.2.1.5.82.1.5
Source Address. This is the source address of the tunnel. This address is put into the source field of the tunnel packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRtunnelLconNo 1.3.6.1.4.1.449.2.1.2.1.5.82.1.7
This parameter specifies the LCON which will be used to forward the tunneled packet. If the value got is '0', then it means that this is a LAN TUNNEL with cdx6500PCTRtunnelLANnxthopAddr specifing Nexthop IP address corresponding to a LAN interface. Non-Zero value indicates this as a WAN TUNNEL. 1-MAX-LCON => For tunnels going on WAN link. 0 => For tunnels going on LAN link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2000  

cdx6500PCTRtunnelIfNo 1.3.6.1.4.1.449.2.1.2.1.5.82.1.9
This parameter specifies the router interface number used by this tunnel. If the value got is '0', it means that the value has not been prompted in the Tunnel Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 5..1000  

cdx6500PCTRtunnelEncrProf 1.3.6.1.4.1.449.2.1.2.1.5.82.1.12
This parameter specifies the profile name of the encryption profile table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cdx6500PCTRtunnelProt 1.3.6.1.4.1.449.2.1.2.1.5.82.1.2
This parameter specifies the protocol used for tunneling. This defaults to GRE (Generic Routing Encapsulation)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER gre(1), l2tp(2)  

cdx6500PCTRtunnelGreCksSqn 1.3.6.1.4.1.449.2.1.2.1.5.82.1.3
This parameter enables or disables the GRE configuration. CKS enables end-to-end checksum, SQN enables sequence number. A combination of these can also be specified. Example : CKS+SQN
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3..20)  

cdx6500PCTRtunnelPayProt 1.3.6.1.4.1.449.2.1.2.1.5.82.1.8
This parameter specifies the accepted protocol types of the payload data. A combination of these can also be specified (for instance:IP+IPX). If the packet protocol type doesn't match the configured protocol type ,the packet is dropped.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..20)  

cdx6500PCTRtunnelDebug 1.3.6.1.4.1.449.2.1.2.1.5.82.1.13
This parameter enables reports for diagnostic purposes in the data passing state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

cdx6500PCTRtunnelLANnxthopAddr 1.3.6.1.4.1.449.2.1.2.1.5.82.1.14
LAN Next Hop IP address. This parameter specifies the LAN Next hop IP address corresponding to a LAN interface which will be used to forward the tunneled packets for LAN tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PCTRtunnelRtpHdrComProf 1.3.6.1.4.1.449.2.1.2.1.5.82.1.10
This parameter specifies the profile name in the RTP/UDP/IP compression profile table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

cdx6500PCTRtunnelGreResyncCntr 1.3.6.1.4.1.449.2.1.2.1.5.82.1.4
This parameter specifies the Resynchronisation Counter that is used by the receiver. If the value got is '0', it means that the value has not been prompted in the Tunnel Table
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..64  

cdx6500PCTRtunnelBrdgLnkNo 1.3.6.1.4.1.449.2.1.2.1.5.82.1.11
This parameter specifies the bridge link used by this tunnel. If the value got is '0', it means that the value has not been prompted in the Tunnel Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 5..1000  

cdx6500PSTRtunnelTable 1.3.6.1.4.1.449.2.1.3.1.4.4
Tunnel Statistics Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PSTRtunnelEntry

cdx6500PSTRtunnelEntry 1.3.6.1.4.1.449.2.1.3.1.4.4.1
Tunnel Statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PSTRtunnelEntry  

cdx6500PSTRtunnelIndex 1.3.6.1.4.1.449.2.1.3.1.4.4.1.1
Table Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

cdx6500PSTRtunnelIpPktIn 1.3.6.1.4.1.449.2.1.3.1.4.4.1.2
This parameter specifies the number of IP packets that have been received by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelIpPktOut 1.3.6.1.4.1.449.2.1.3.1.4.4.1.3
This parameter specifies the number of IP packets that have been sent out by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelIpPktDisc 1.3.6.1.4.1.449.2.1.3.1.4.4.1.4
This parameter specifies the number of IP packets that have been discarded by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelIpxPktIn 1.3.6.1.4.1.449.2.1.3.1.4.4.1.5
This parameter specifies the number of IPX packets that have been received by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelIpxPktOut 1.3.6.1.4.1.449.2.1.3.1.4.4.1.6
This parameter specifies the number of IPX packets that have been sent out by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelIpxPktDisc 1.3.6.1.4.1.449.2.1.3.1.4.4.1.7
This parameter specifies the number of IPX packets that have been discarded by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelSrcAddr 1.3.6.1.4.1.449.2.1.3.1.4.4.1.8
Source Address. This is the source address of the tunnel. This address is put into the source field of the tunnel packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PSTRtunnelDstAddr 1.3.6.1.4.1.449.2.1.3.1.4.4.1.9
Destination Address.This is the destination address of the tunnel. This address is put into the destination field of the tunnel packet. This field cannot be 0.0.0.0 or un-numbered address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

cdx6500PSTRtunnelPayProt 1.3.6.1.4.1.449.2.1.3.1.4.4.1.10
This parameter specifies the accepted protocol types of the payload data. A combination of thse can also be specified (for instance:IP+IPX+BRG). If the packet protocol type doesn't match the configured protocol type ,the packet is dropped.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), brg(4), ip-ipx(3), ip-brg(5), ipx-brg(6), ip-ipx-brg(7)  

cdx6500PSTRtunnelEncrStatus 1.3.6.1.4.1.449.2.1.3.1.4.4.1.11
This parameter gives the status of the ENCRYPTION Channel
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..16)  

cdx6500PSTRtunnelRuihcStatus 1.3.6.1.4.1.449.2.1.3.1.4.4.1.12
This parameter gives the status of the RTP/UDP/IP Header Compression of the given tunnel
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ena(1), dis(2)  

cdx6500PSTRtunnelBrdgPktIn 1.3.6.1.4.1.449.2.1.3.1.4.4.1.13
This parameter specifies the number of BRIDGE packets that have been received by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelBrdgPktOut 1.3.6.1.4.1.449.2.1.3.1.4.4.1.14
This parameter specifies the number of BRIDGE packets that have been sent out by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PSTRtunnelBrdgPktDisc 1.3.6.1.4.1.449.2.1.3.1.4.4.1.15
This parameter specifies the number of BRIDGE packets that have been discarded by the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER