SALIX-DS1-MIB
File:
SALIX-DS1-MIB.mib (6586 bytes)
Imported modules
Imported symbols
Defined Types
SalixDsx1ConfigEntry |
|
SEQUENCE |
|
|
|
|
salixDsx1ContinuityTestType |
INTEGER |
|
|
salixDsx1DChannelPresent |
TruthValue |
|
|
salixDsx1AutoInitiateState |
TruthValue |
|
|
salixDsx1DChannelMode |
INTEGER |
|
|
salixDsx1RobbedBitSignalling |
INTEGER |
|
|
salixDsx1TDMEchoCancellation |
INTEGER |
|
Defined Values
salixDsx1MIB |
1.3.6.1.4.1.2158.2.7 |
The MIB describing objects relating to DS1 interfaces, specifically
items that augment objects from the DS1-MIB |
MODULE-IDENTITY |
|
|
|
salixDsx1ConfigTable |
1.3.6.1.4.1.2158.2.7.1.1 |
The SALIX DS1 config table This table augments the
dsx1ConfigTable defined in the DS1 MIB. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SalixDsx1ConfigEntry |
|
salixDsx1ConfigEntry |
1.3.6.1.4.1.2158.2.7.1.1.1 |
An entry in the SALIX DS1 config table. This entry
containts SALIX specific DS1 configuration objects |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SalixDsx1ConfigEntry |
|
|
salixDsx1ContinuityTestType |
1.3.6.1.4.1.2158.2.7.1.1.1.1 |
The type of continuity test that should be setup. An entry exists for
every DS1 in the system. This object is
consulted when IPDC is requested to setup a continuity test. Since
this value is specified in SGCP, it is not consulted if the SGCP
protocol is used. Writing to this value has the effect that it changes
the continuity test type for any subsequently setup continuity tests. Any
tests currently in progress are not effected by changing this object. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
loopback(1), transponder(2) |
|
salixDsx1DChannelPresent |
1.3.6.1.4.1.2158.2.7.1.1.1.2 |
An indication of whether channel 24 of the DS1 is reserved for D channel
signaling. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
salixDsx1AutoInitiateState |
1.3.6.1.4.1.2158.2.7.1.1.1.3 |
An indication of whether the D channel data link control (layer 2)
should be initiated automatically during DS1 initialization or
brought up on demand. This attribute is only relevant if
salixDsx1DChannelPresent is 'true'. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
salixDsx1DChannelMode |
1.3.6.1.4.1.2158.2.7.1.1.1.4 |
An indication of whether the D Channel (if present) on the given
DS1 should be configured as 'user mode' or as 'network mode'.
This attributes is only used if the salixDsx1DChannelPresent field
is set to 'true' |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
userMode(1), networkMode(2) |
|
salixDsx1RobbedBitSignalling |
1.3.6.1.4.1.2158.2.7.1.1.1.5 |
An indication of whether the 'ABCD' bits of the DS0s in the DS1
should be configured for robbed bit signalling. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(0), onHook(1), offHook(2), ringing(3) |
|
salixDsx1TDMEchoCancellation |
1.3.6.1.4.1.2158.2.7.1.1.1.7 |
An indication of whether echo cancellation should be applied
to the DS0s in the DS1.
echoCancel16ms - 16 millisecond echo cancellation tail length
echoCancel32ms - 32 millisecond echo cancellation tail length
echoCancel63ms - 63 millisecond echo cancellation tail length |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(0), echoCancel16ms(1), echoCancel32ms(2), echoCancel63ms(3) |
|
salixDs1Group |
1.3.6.1.4.1.2158.2.7.3.1.1 |
Salix DS1 Objects Group |
Status: current |
Access: read-write |
OBJECT-GROUP |
|
|
|
salixDs1Compliance |
1.3.6.1.4.1.2158.2.7.3.2.1 |
The basic implementation requirements for the SALIX-DS1-MIB. |
Status: current |
Access: read-write |
MODULE-COMPLIANCE |
|
|
|