SIAE-RADIO-SYSTEM-MIB

File: SIAE-RADIO-SYSTEM-MIB.mib (164370 bytes)

Imported modules

SNMPv2-SMI IF-MIB SNMPv2-TC
SIAE-TREE-MIB SIAE-ALARM-MIB SIAE-EQUIP-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Counter32 InterfaceIndexOrZero
TEXTUAL-CONVENTION DisplayString RowStatus
StorageType siaeMib AlarmStatus
AlarmSeverityCode alarmTrap equipIpSnmpAgentAddress

Defined Types

ChannelSpacing  
This TC describes a data type which identifies a RF channel spacing.
TEXTUAL-CONVENTION    
  INTEGER bw3M5Hz(0), bw7Mhz(1), bw14MHz(2), bw28MHz(3), bw40MHz(5), bw56MHz(4), bw112MHz(6), bw250Mhz(7), bw500Mhz(8), bw750Mhz(9), bw1000Mhz(10), bw10Mhz(11), bw20Mhz(12), bw30Mhz(13), bw50Mhz(14), bw60Mhz(15), bw80Mhz(16)  

ModulationMap  
This data type is used as the syntax of the radioBranchModulationMap and radioBranchRefModulationMap objects.
TEXTUAL-CONVENTION    
  BITS modBPSK(0), mod4QAM(1), mod8PSK(2), mod16QAM(3), mod32QAM(4), mod64QAM(5), mod128QAM(6), mod256QAM(7), mod512QAM(8), mod1024QAM(9), mod2048QAM(10), mod4096QAM(11)  

ConfigMismatchReason  
This data type is used to specify the cause of Config Mismatch Alarm, that is the mismatch between the radio link capability and the current local and remote configuration. - securityMismatch(0) Copyright violation - frequencyFailMismatch(1) Configured frequency is out of Filter-Bandwidth - frequencyAlertMismatch(2) Configured frequency across Filter-Bandwidth - ptxMismatch(3) Tx power configured incongruent with RF Tx power limits - channelSpacingAndModulationMismatch(4) Bandwidth and/or modulation configured is invalid (RF doesn't support it) - remoteConfigurationMismatch(5) Incongruence between the couple of Terminal Radio Unit (TRU) in the link: - Frequency Incongruent (Freq) - Reference Bandwidth and Modulation incongruent - Acm-Tx map in congruent with remote Acm-Rx map - acmMismatch(6) Obsolete (no longer used) - profileSetMismatch(7) The selected profile set is not supported by the TRU
TEXTUAL-CONVENTION    
  BITS securityMismatch(0), frequencyFailMismatch(1), frequencyAlertMismatch(2), ptxMismatch(3), channelSpacingAndModulationMismatch(4), remoteConfigurationMismatch(5), acmMismatch(6), profileSetMismatch(7)  

RadioCapability  
This data type is used as the syntax of the radioBranchKeyFeatures objects.
TEXTUAL-CONVENTION    
  BITS reserved(0), trafficSquelch(1), baseBandLoop(2), maxPower(3), carrierOnly(4), iQLoop(5), rfLoopGivenMod(6), rfLoopAnyMod(7)  

BitsPerSymbol  
his TC describes a data type which identifies a RF channel spacing.
TEXTUAL-CONVENTION    
  INTEGER bpsBPSK(1), bps4QAM(2), bps8PSK(3), bps16QAM(4), bps32QAM(5), bps64QAM(6), bps128QAM(7), bps256QAM(8), bps512QAM(9), bps1024QAM(10), bps2048QAM(11), bps4096QAM(12)  

Stm1IndexOrZero  
This textual convention permits the additional value of zero to an stm1Index in stm1Table. The value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where stm-1 was unknown, or when none or all stm-1s need to be referenced.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

RadioEntry  
SEQUENCE    
  radioIndex Integer32
  radioLabel DisplayString
  radioType INTEGER
  radioIfIndex InterfaceIndexOrZero
  radioStorageType StorageType

XpicEntry  
SEQUENCE    
  xpicIndex Integer32
  xpicRadioIdx Integer32
  xpicRowstatus RowStatus

XpicChEntry  
SEQUENCE    
  xpicChPolIndex Integer32
  xpicChRadioIdx Integer32
  xpicChRowstatus RowStatus

LinkEntry  
SEQUENCE    
  linkIndex Integer32
  linkType INTEGER
  linkLabel DisplayString
  linkIfIndex InterfaceIndexOrZero
  linkRowstatus RowStatus

LinkChEntry  
SEQUENCE    
  linkChIndex Integer32
  linkChRadioIdx Integer32
  linkChRadioSettingsIdx Integer32
  linkChRowstatus RowStatus

LinkSettingsEntry  
SEQUENCE    
  linkBandwidthAndModulation Integer32
  linkAcmEngineEnable INTEGER
  linkTxUpperProfile INTEGER
  linkTxLowerProfile INTEGER
  linkId INTEGER
  linkTxPwrThresh INTEGER
  linkRxPwrThresh INTEGER
  linkSynchSetupProtocolEnable INTEGER
  linkProfilesSetSelection INTEGER
  linkXpicControlProcedure INTEGER

RadioSettingsEntry  
SEQUENCE    
  radioSettingsIndex Integer32
  radioSettingsRowStatus RowStatus
  radioSettingsLabel DisplayString
  radioTxFrequency INTEGER
  radioDuplexFrequency INTEGER
  radioTxAttenuation INTEGER
  radioAtpcManual INTEGER
  radioAtpcPwrHigh Integer32
  radioAtpcPwrLow Integer32
  radioAtpcRange Integer32
  radioFreqTableSelection ChannelSpacing

TdmSettingsEntry  
SEQUENCE    
  tdmPolIndex Integer32
  tdmE1Channel Integer32
  tdmE1Framer INTEGER

RadioCapabilitiesEntry  
SEQUENCE    
  radioCapabilitiesCapability RadioCapability
  radioCapabilitiesTxMinFrequency Integer32
  radioCapabilitiesTxMaxFrequency Integer32
  radioCapabilitiesStepFrequency Integer32
  radioCapabilitiesMinPtxNominalValue Integer32
  radioCapabilitiesMaxPtxNominalValue Integer32
  radioCapabilitiesExtendedMinPwr Integer32

RadioStatusEntry  
SEQUENCE    
  radioCurrentDuplexFrequency Integer32
  radioTxChannelSpacing Integer32
  radioPrx Integer32
  radioPtx Integer32
  radioNormalizedMse Integer32
  radioRxActiveStatus INTEGER
  radioTxActiveStatus INTEGER
  radioCableOpenAlarm AlarmStatus
  radioCableShortAlarm AlarmStatus
  radioInvalidFrequencyAlarm AlarmStatus
  radioBaseBandRxAlarm AlarmStatus
  radioModulatorFailAlarm AlarmStatus
  radioDemodulatorFailAlarm AlarmStatus
  radioRxPowerLowAlarm AlarmStatus
  radioTxPowerLowAlarm AlarmStatus
  radioRemDemodulatorFailAlarm AlarmStatus
  radioVcoFailAlarm AlarmStatus
  radioRxIFAgcAlarm AlarmStatus
  radioTxIFAgcAlarm AlarmStatus
  radioIduOduCommunicationAlarm AlarmStatus
  radioOduIduCommunicationAlarm AlarmStatus
  radioLocalOduAlarmSynthesis AlarmStatus
  radioRemoteOduAlarmSynthesis AlarmStatus
  radioConfigMismatchAlarm AlarmStatus
  radioConfigAlarmReason ConfigMismatchReason
  radioRxQualityLowAlarm AlarmStatus
  radioRxQualityWarningAlarm AlarmStatus
  radioXpd Integer32

RadioMaintEntry  
SEQUENCE    
  radioTxStatus INTEGER
  radioCarrierOnly INTEGER
  radioLoop INTEGER
  radioRFLoopTestResult INTEGER
  radioRFLoopTestPercTime INTEGER
  radioRtPsuOff INTEGER
  radioLom INTEGER
  radioXpic INTEGER

RadioFreqEntry  
SEQUENCE    
  radioFreqChannelId Integer32
  radioFreqChannelNum Integer32
  radioFreqValue Integer32

RadioDuplexFreqEntry  
SEQUENCE    
  radioDuplexFreqId Integer32
  radioDuplexFreqValue Integer32

RadioModulationEntry  
SEQUENCE    
  radioChannelSpacing ChannelSpacing
  radioModulationMap ModulationMap
  radioRefModulationMap ModulationMap

LinkStatusEntry  
SEQUENCE    
  linkPolIndex INTEGER
  linkAcmRxProfile Integer32
  linkAcmTxProfile Integer32
  linkAcmRxProfileLabel DisplayString
  linkAcmTxProfileLabel DisplayString
  linkAcmRxModulation BitsPerSymbol
  linkAcmTxModulation BitsPerSymbol
  linkAcmRxCode INTEGER
  linkAcmTxCode INTEGER
  linkTxETHCapacity Integer32
  linkRxETHCapacity Integer32
  linkTxTDMCapacity Integer32
  linkRxTDMCapacity Integer32
  linkRescueModulation BitsPerSymbol
  linkReducedCapacityAlarm AlarmStatus
  linkLinkTelemetryFailAlarm AlarmStatus
  linkIdMismatchAlarm AlarmStatus
  linkRadioEocAlarm AlarmStatus
  linkSetupMismatchAlarm AlarmStatus
  linkRescueSetupAlarm AlarmStatus
  linkXpicProcedureBlockAlarm AlarmStatus
  linkXpicRemTxOffAlarm AlarmStatus
  linkRemoteIduAlarmSynthesis AlarmStatus
  linkNotMatchingRadiosAlarm AlarmStatus
  linkConfigurationInProgress INTEGER
  linkXpd Integer32

LinkTfcEntry  
SEQUENCE    
  linkTfcAction INTEGER
  linkTfcControl INTEGER
  linkTfcWatchWindow INTEGER
  linkTfcAlarmThreshold INTEGER
  linkTfcAlarm AlarmStatus
  linkTfcRowStatus RowStatus

LinkMaintEntry  
SEQUENCE    
  linkBerStart INTEGER
  linkBaseBandLom INTEGER
  linkFadeMarginMeasure INTEGER
  linkXpicControlProcedureReset INTEGER

LinkBerEntry  
SEQUENCE    
  linkBerErrorCounterH Counter32
  linkBerErrorCounterL Counter32
  linkBerDataCounterH Counter32
  linkBerDataCounterL Counter32
  linkBerSyncLossAlarm AlarmStatus
  linkBerSyncLossAlarmCounter Integer32
  linkBerElapsedTime Integer32

LinkAcmEntry  
SEQUENCE    
  linkAcmProfileId Integer32
  linkAcmProfileModulation BitsPerSymbol
  linkAcmProfileCode INTEGER
  linkAcmProfileCapacity Integer32
  linkAcmProfileLabel DisplayString
  linkAcmMaxTDMCapacity Integer32
  linkAcmPowerScaling Integer32
  linkAcmProfileEnable INTEGER
  linkAcmDownshiftThreshold Integer32
  linkAcmUpshiftThreshold Integer32
  linkAcmActiveProfile INTEGER
  linkAcmTDMCapacity Integer32
  linkAcmETHCapacity Integer32
  linkAcmAtpcRxPowerScaling Integer32
  linkAcmPowerRange Integer32

LinkProEntry  
SEQUENCE    
  linkProProtectionTxChIdx Integer32
  linkProProtectionRxChIdx Integer32
  linkProTxWtrTime INTEGER
  linkProRxWtrTime INTEGER
  linkProTxSwitchedChIdx Integer32
  linkProRxSwitchedChIdx Integer32
  linkProTxRevertive INTEGER
  linkProRxRevertive INTEGER
  linkProExtraTraffic INTEGER
  linkProRowStatus RowStatus

LinkProMaintEntry  
SEQUENCE    
  linkProMaintTxLockout INTEGER
  linkProMaintRxLockout INTEGER
  linkProMaintTxForced Integer32
  linkProMaintRxForced Integer32
  linkProMaintTxWtrReset INTEGER
  linkProMaintRxWtrReset INTEGER

LinkCapabilitiesEntry  
SEQUENCE    
  linkCapabilitiesCapability RadioCapability
  linkCapabilitiesTxMinFrequency Integer32
  linkCapabilitiesTxMaxFrequency Integer32
  linkCapabilitiesStepFrequency Integer32
  linkCapabilitiesMinPtxNominalValue Integer32
  linkCapabilitiesMaxPtxNominalValue Integer32
  linkCapabilitiesExtendedMinPwr Integer32

LinkFreqEntry  
SEQUENCE    
  linkFreqChannelId Integer32
  linkFreqChannelNum Integer32
  linkFreqValue Integer32

LinkDuplexFreqEntry  
SEQUENCE    
  linkDuplexFreqId Integer32
  linkDuplexFreqValue Integer32

LinkModulationEntry  
SEQUENCE    
  linkChannelSpacing ChannelSpacing
  linkModulationMap ModulationMap
  linkRefModulationMap ModulationMap

CombinedRadioCapabilitiesEntry  
SEQUENCE    
  combinedRadioCapabilitiesCapability RadioCapability
  combinedRadioCapabilitiesTxMinFrequency Integer32
  combinedRadioCapabilitiesTxMaxFrequency Integer32
  combinedRadioCapabilitiesStepFrequency Integer32
  combinedRadioCapabilitiesMinPtxNominalValue Integer32
  combinedRadioCapabilitiesMaxPtxNominalValue Integer32
  combinedRadioCapabilitiesExtendedMinPwr Integer32

CombinedRadioFreqEntry  
SEQUENCE    
  combinedRadioFreqChannelId Integer32
  combinedRadioFreqChannelNum Integer32
  combinedRadioFreqValue Integer32

CombinedRadioDuplexFreqEntry  
SEQUENCE    
  combinedRadioDuplexFreqId Integer32
  combinedRadioDuplexFreqValue Integer32

CombinedRadioPowerScalingEntry  
SEQUENCE    
  combinedRadioPowerScaling Integer32
  combinedRadioAtpcRxPowerScaling Integer32
  combinedRadioPowerRange Integer32

Stm1BulkMappingEntry  
SEQUENCE    
  stm1BulkPolIndex Integer32
  stm1BulkChanIndex Integer32
  stm1BulkChannel Stm1IndexOrZero

LinkE1vsSTM1CapacityEntry  
SEQUENCE    
  linkE1vsSTM1CapacityStm1 Integer32
  linkE1vsSTM1CapacityE1 Integer32

LinkTfcV2Entry  
SEQUENCE    
  linkTfcV2Action INTEGER
  linkTfcV2Control INTEGER
  linkTfcV2WatchWindow INTEGER
  linkTfcV2AlarmThreshold INTEGER
  linkTfcV2Alarm AlarmStatus
  linkTfcV2RowStatus RowStatus

LinkProV2Entry  
SEQUENCE    
  linkProV2ProtectionTxChIdx Integer32
  linkProV2ProtectionRxChIdx Integer32
  linkProV2TxWtrTime INTEGER
  linkProV2RxWtrTime INTEGER
  linkProV2TxSwitchedChIdx Integer32
  linkProV2RxSwitchedChIdx Integer32
  linkProV2TxRevertive INTEGER
  linkProV2RxRevertive INTEGER
  linkProV2ExtraTraffic INTEGER
  linkProV2RowStatus RowStatus

LinkProMaintV2Entry  
SEQUENCE    
  linkProMaintV2TxLockout INTEGER
  linkProMaintV2RxLockout INTEGER
  linkProMaintV2TxForced Integer32
  linkProMaintV2RxForced Integer32
  linkProMaintV2TxWtrReset INTEGER
  linkProMaintV2RxWtrReset INTEGER

SspEntry  
SEQUENCE    
  sspParameterType INTEGER
  sspLinkBandwidth INTEGER
  sspLinkModulation INTEGER
  sspLinkAcmEngineEnable INTEGER
  sspLinkTxUpperProfile INTEGER
  sspLinkTxLowerProfile INTEGER
  sspLinkSynchSetupProtocolEnable INTEGER
  sspLinkProfilesSetSelection INTEGER
  sspTdmE1Channel Integer32
  sspTdmStm1Channel Integer32

RadioLoopCapabilityEntry  
SEQUENCE    
  radioLoopRfGroup Integer32
  radioLoopIqGroup Integer32
  radioLoopBaseBandGroup Integer32

RadioRxBerThresholdEntry  
SEQUENCE    
  radioRxBerThresholdStatus INTEGER
  radioNominalRxBerThreshold Integer32
  radioMeasuredRxBerThreshold Integer32

Defined Values

radioSystem 1.3.6.1.4.1.3373.1103.80
Radio System MIB.
MODULE-IDENTITY    

radioSystemMibVersion 1.3.6.1.4.1.3373.1103.80.1
Numerical version of this module. The string version of this MIB have the following format: XX.YY.ZZ so, for example, the value 1 should be interpreted as 00.00.01 and the value 10001 should be interpreted as 01.00.01.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radioTable 1.3.6.1.4.1.3373.1103.80.2
A list of radio interface entries. This table is useful to show the manager all the available radio interfaces on the equipment. Moreover it is a reference for Performance Monitoring (PWR and G828).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioEntry

radioEntry 1.3.6.1.4.1.3373.1103.80.2.1
An entry containing management information applicable to a particular radio interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioEntry  

radioIndex 1.3.6.1.4.1.3373.1103.80.2.1.1
A unique value, greater than zero, for each radio interface. It is recommended that values are assigned contiguously starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioLabel 1.3.6.1.4.1.3373.1103.80.2.1.2
A textual string containing information about the radio interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

radioType 1.3.6.1.4.1.3373.1103.80.2.1.3
The type of interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), analogRadio(2), digitalRadio(3), xpicRadio(4)  

radioIfIndex 1.3.6.1.4.1.3373.1103.80.2.1.4
This object defines a greater than zero value to identify an interface in ifTable or a zero value if ifTable is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

radioStorageType 1.3.6.1.4.1.3373.1103.80.2.1.5
The storage type of this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current Access: read-only
OBJECT-TYPE    
  StorageType  

xpicTable 1.3.6.1.4.1.3373.1103.80.3
A list of xpic radio interface entries. If a manager wants to make an xpic link, it should only add a particular xpic radio interface to an xpic link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XpicEntry

xpicEntry 1.3.6.1.4.1.3373.1103.80.3.1
An entry containing management information applicable to a particular xpic radio interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  XpicEntry  

xpicIndex 1.3.6.1.4.1.3373.1103.80.3.1.1
A unique value, greater than zero, for each xpic radio interface. It is recommended that values are assigned contiguously starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xpicRadioIdx 1.3.6.1.4.1.3373.1103.80.3.1.2
Index of xpic radio interface, corresponding to an available xpic radio interface in radioTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xpicRowstatus 1.3.6.1.4.1.3373.1103.80.3.1.3
Status of this conceptual row in xpicTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xpicChTable 1.3.6.1.4.1.3373.1103.80.4
A list of xpic channel entries. This table maps each xpic radio in respective xpic radio interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XpicChEntry

xpicChEntry 1.3.6.1.4.1.3373.1103.80.4.1
An entry containing management information applicable to a particular xpic channel. It defines radio interface and polarization for a given xpic channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  XpicChEntry  

xpicChPolIndex 1.3.6.1.4.1.3373.1103.80.4.1.1
This object identifies the xpic radio polarization.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

xpicChRadioIdx 1.3.6.1.4.1.3373.1103.80.4.1.2
Xpic radio interface, corresponding to a radio interface in radioTable, used to make up the given xpic radio interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xpicChRowstatus 1.3.6.1.4.1.3373.1103.80.4.1.3
Status of this conceptual row in xpicChTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

linkAvailableIndex 1.3.6.1.4.1.3373.1103.80.5
Shows an index which is available for creation of a new link in the system. It shows the smallest available index. Any attempt to create a link with a different index results in a failure.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkTable 1.3.6.1.4.1.3373.1103.80.6
A list of link entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkEntry

linkEntry 1.3.6.1.4.1.3373.1103.80.6.1
An entry containing management information applicable to a particular link.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkEntry  

linkIndex 1.3.6.1.4.1.3373.1103.80.6.1.1
A unique value, greater than zero, for each link. Manager must use the first available index, suggested by linkAvailableIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkType 1.3.6.1.4.1.3373.1103.80.6.1.2
This object identifies link type. Supported link types are: single link, 1+1 Hot Standby, 1+1 Frequency Diversity, 2+0 XPIC, 2+2 XPIC Hot Standby, 2+2 XPIC Frequency Diversity and N+1.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER radio1p0(1), radio1p1HS(2), radio1p1FD(3), radio2p0Xpic(4), radio2p2XpicHS(5), radio2p2XpicFD(6), radioNp1(7)  

linkLabel 1.3.6.1.4.1.3373.1103.80.6.1.3
A textual string containing information about the link. This string should give more details about link specific parameters.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkIfIndex 1.3.6.1.4.1.3373.1103.80.6.1.4
This object defines a greater than zero value to identify a link in ifTable or a zero value if ifTable is not supported.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

linkRowstatus 1.3.6.1.4.1.3373.1103.80.6.1.5
Status of this row of linkTable. This object is used to manage the creation and deletion of conceptual rows in linkTable. To create a row in this table, a manager should set rowstatus to createAndWait(5) and choose a link type. Respective entries in linkSettingsTable, linkStatusTable and tdmSettingsTable will be created by agent.In case of protection links proper entries in linkProtectionTable will be also created. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of rowstatus is notReady(3). When there is sufficient information to (attempt to) make the conceptual row available for use by the managed device, then the rowstatus column turns into notInService(2); manager must set rowstatus to active(1) to make the conceptual row active. The contents of linkSettingsTable and radioSettingsTable can be changed only if this object is notInService(2).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

linkChTable 1.3.6.1.4.1.3373.1103.80.7
A list of link channel entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkChEntry

linkChEntry 1.3.6.1.4.1.3373.1103.80.7.1
An entry containing management information applicable to a particular link channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkChEntry  

linkChIndex 1.3.6.1.4.1.3373.1103.80.7.1.1
Link Channel Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkChRadioIdx 1.3.6.1.4.1.3373.1103.80.7.1.2
Radio channel index that corresponds to an available radio interface in radioTable.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

linkChRadioSettingsIdx 1.3.6.1.4.1.3373.1103.80.7.1.3
Radio Settings Index. This object is a foreign key for a corresponding radioSettingsTable entry, which is automatically created by agent.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

linkChRowstatus 1.3.6.1.4.1.3373.1103.80.7.1.4
Status of this row of linkChTable. This object is used to manage the creation and deletion of conceptual rows in linkChTable. To create a row in this table, a manager should set rowstatus to createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of rowstatus is notReady(3). When there is sufficient information to (attempt to) make the conceptual row available for use by the managed device, then the rowstatus column turns into notInService(2); manager must set rowstatus to active(1) to make the conceptual row active. The content of radioSettingsTable can be changed only if this object is notInService(2).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

linkSettingsTable 1.3.6.1.4.1.3373.1103.80.8
Table with link settings entries. This table contains all parameters of a radio frequency link. The content of this table can be changed by a manager if linkRowStatus is notInService(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkSettingsEntry

linkSettingsEntry 1.3.6.1.4.1.3373.1103.80.8.1
Radio link entry
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkSettingsEntry  

linkBandwidthAndModulation 1.3.6.1.4.1.3373.1103.80.8.1.1
Link Modulation and Bandwidth (channel spacing). The value of this object value is computed by: 65536*modulation+bandwidth where bandwidth selection is: 0 = 3.5Mhz 1 = 7MHz 2 = 14MHz 3 = 28MHz 4 = 56MHz 5 = 10MHz 6 = 20MHz 7 = 30MHz 8 = 40MHz 9 = 50MHz 10 = 112Mhz 11 = 250Mhz 12 = 500Mhz 13 = 750Mhz 14 = 1Ghz 15 = 60MHz 16 = 80MHz and modulation is in bit-per-symbol: 1 = BPSK 2 = 4QAM 3 = 8PSK 4 = 16QAM 5 = 32QAM 6 = 64QAM 7 = 128QAM 8 = 256QAM 9 = 512QAM 10 = 1024QAM 11 = 2048QAM. 12 = 4096QAM. Examples: 250Mhz-4QAM (131083), 500Mhz-4QAM (131084), 250Mhz-16QAM (262155), 500Mhz-64QAM (393228). Note: 0 bit-per-symbol is not possible, so value 0 is used for BandwidthAndModulation unassigned.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

linkAcmEngineEnable 1.3.6.1.4.1.3373.1103.80.8.1.2
This object is used to enable/disable the ACM engine
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkTxUpperProfile 1.3.6.1.4.1.3373.1103.80.8.1.3
The object (and linkTxLowerProfile object) is used to restrict the TX profile range when ACM is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

linkTxLowerProfile 1.3.6.1.4.1.3373.1103.80.8.1.4
The object (and linkTxUpperProfile object) is used to restrict the TX profile range when ACM is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

linkId 1.3.6.1.4.1.3373.1103.80.8.1.5
Link Identification (value 0..255)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

linkTxPwrThresh 1.3.6.1.4.1.3373.1103.80.8.1.6
Threshold (value +3 , +15 dB) relative to nominal value of the TX power below wich the related alarm is set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 3..15  

linkRxPwrThresh 1.3.6.1.4.1.3373.1103.80.8.1.7
Threshold (value -40 , -99 dBm) for RX power below wich the related alarm is set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -99..-40  

linkSynchSetupProtocolEnable 1.3.6.1.4.1.3373.1103.80.8.1.8
Synchronization Setup Protocol (SSP) control
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProfilesSetSelection 1.3.6.1.4.1.3373.1103.80.8.1.9
Selection of the working profile set between high gain (max robustness) profile set and high throughput (max capacity) profile set. The set of profiles high gain features a greater robustness against to the set of profiles high throughput. For radio systems that do not have more sets of profiles, this object becomes read only and its reading shows the only one set of profiles supported.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER highThroughput(1), highGain(2)  

linkXpicControlProcedure 1.3.6.1.4.1.3373.1103.80.8.1.10
Set by manager to enable\disable XPIC alarm control procedure. Only for XPIC configurations.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

radioSettingsTable 1.3.6.1.4.1.3373.1103.80.9
Table with radio settings entries. This table contains all parameters of a radio terminal. The content of this table can be changed only linkRowStatus is notInService(2)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioSettingsEntry

radioSettingsEntry 1.3.6.1.4.1.3373.1103.80.9.1
Radio terminal entry
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioSettingsEntry  

radioSettingsIndex 1.3.6.1.4.1.3373.1103.80.9.1.1
Radio settings index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioSettingsRowStatus 1.3.6.1.4.1.3373.1103.80.9.1.2
Status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

radioSettingsLabel 1.3.6.1.4.1.3373.1103.80.9.1.3
A textual string containing information about the radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

radioTxFrequency 1.3.6.1.4.1.3373.1103.80.9.1.4
Transmitted frequency in KHz. Null value means invalid frequency.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

radioDuplexFrequency 1.3.6.1.4.1.3373.1103.80.9.1.5
Value of duplex frequency in KHz. -2 means not set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

radioTxAttenuation 1.3.6.1.4.1.3373.1103.80.9.1.6
Transmitter attenuation relative to nominal power (dBm).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

radioAtpcManual 1.3.6.1.4.1.3373.1103.80.9.1.7
Enables/disables Atpc Manual operation.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

radioAtpcPwrHigh 1.3.6.1.4.1.3373.1103.80.9.1.8
ATPC Control - Local Rx Power High (dBm range -30 to -80) -.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

radioAtpcPwrLow 1.3.6.1.4.1.3373.1103.80.9.1.9
ATPC Control - Local Rx Power Low (dBm range -30 to -80) -.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

radioAtpcRange 1.3.6.1.4.1.3373.1103.80.9.1.10
Defines the range of the ATPC regulation (expressed in dB) with respect to the current value of maximum Tx output, that is intended as the upper limit of the range. A null value means no limit: the lower limit of the range is equal to minimum Ptx.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

radioFreqTableSelection 1.3.6.1.4.1.3373.1103.80.9.1.11
RadioFrequencyTable key (channel spacing & modulation) selection.
Status: current Access: read-create
OBJECT-TYPE    
  ChannelSpacing  

tdmSettingsTable 1.3.6.1.4.1.3373.1103.80.10
Table with tdm settings entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TdmSettingsEntry

tdmSettingsEntry 1.3.6.1.4.1.3373.1103.80.10.1
An entry containing tdm parameters for a particular link.
Status: current Access: not-accessible
OBJECT-TYPE    
  TdmSettingsEntry  

tdmPolIndex 1.3.6.1.4.1.3373.1103.80.10.1.1
Polarization index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

tdmE1Channel 1.3.6.1.4.1.3373.1103.80.10.1.2
Number of E1 channels. This object is used to define the capacity of E1 tributaries assigned to a given radio link. The capacity is changed in steps of E1 (2Mbit/s).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

tdmE1Framer 1.3.6.1.4.1.3373.1103.80.10.1.3
This object is used to attach the framer to a given E1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

radioCapabilitiesTable 1.3.6.1.4.1.3373.1103.80.11
Table with RadioCapabilities entries: there is an entry for each radioTable rows.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioCapabilitiesEntry

radioCapabilitiesEntry 1.3.6.1.4.1.3373.1103.80.11.1
RadioCapabilities entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioCapabilitiesEntry  

radioCapabilitiesCapability 1.3.6.1.4.1.3373.1103.80.11.1.1
Bit map to describe the radio features.
Status: current Access: read-only
OBJECT-TYPE    
  RadioCapability  

radioCapabilitiesTxMinFrequency 1.3.6.1.4.1.3373.1103.80.11.1.2
Minimum of available channel frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioCapabilitiesTxMaxFrequency 1.3.6.1.4.1.3373.1103.80.11.1.3
Maximum of available channel frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioCapabilitiesStepFrequency 1.3.6.1.4.1.3373.1103.80.11.1.4
Minimum frequency step in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioCapabilitiesMinPtxNominalValue 1.3.6.1.4.1.3373.1103.80.11.1.5
Minimum nominal Ptx in dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioCapabilitiesMaxPtxNominalValue 1.3.6.1.4.1.3373.1103.80.11.1.6
Maximum nominal Ptx in dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioCapabilitiesExtendedMinPwr 1.3.6.1.4.1.3373.1103.80.11.1.7
Minimum extended Ptx power for fade margin.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioStatusTable 1.3.6.1.4.1.3373.1103.80.12
Table with RadioStatus records: one record for 1+0 configuration and two record for 1+1 configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioStatusEntry

radioStatusEntry 1.3.6.1.4.1.3373.1103.80.12.1
RadioStatus record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioStatusEntry  

radioCurrentDuplexFrequency 1.3.6.1.4.1.3373.1103.80.12.1.1
Spacing between transmitted and received frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioTxChannelSpacing 1.3.6.1.4.1.3373.1103.80.12.1.2
Half of transmitted signal channel spacing in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioPrx 1.3.6.1.4.1.3373.1103.80.12.1.3
Received power level (dBm).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioPtx 1.3.6.1.4.1.3373.1103.80.12.1.4
Transmitted power level (dBm).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioNormalizedMse 1.3.6.1.4.1.3373.1103.80.12.1.5
Normalized MSE (Mean Squared Error) is an indicator of the Signal to Noise (S/N) ratio. It's in 0.1 dB steps
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioRxActiveStatus 1.3.6.1.4.1.3373.1103.80.12.1.6
Receiver Active status with associated Severity In 1+1 Hot Standby radio system, only one RX is active. RXs are active in other configurations of the radio system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cleared(1), active(2)  

radioTxActiveStatus 1.3.6.1.4.1.3373.1103.80.12.1.7
Transmitter Active status with associated Severity. In 1+1 Hot Standby radio system, only one TX is active. TXs are active in other configurations of the radio system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cleared(1), active(2)  

radioCableOpenAlarm 1.3.6.1.4.1.3373.1103.80.12.1.8
Cable connnecting ODU is open: alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioCableShortAlarm 1.3.6.1.4.1.3373.1103.80.12.1.9
Cable connnecting ODU is in short-circuit: alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioInvalidFrequencyAlarm 1.3.6.1.4.1.3373.1103.80.12.1.10
Invalid frequency alarm with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioBaseBandRxAlarm 1.3.6.1.4.1.3373.1103.80.12.1.11
Base Band Rx alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioModulatorFailAlarm 1.3.6.1.4.1.3373.1103.80.12.1.12
Modulator Fail Alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioDemodulatorFailAlarm 1.3.6.1.4.1.3373.1103.80.12.1.13
Demodulator Fail Alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioRxPowerLowAlarm 1.3.6.1.4.1.3373.1103.80.12.1.14
Receiver power low alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioTxPowerLowAlarm 1.3.6.1.4.1.3373.1103.80.12.1.15
Transmitter power low alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioRemDemodulatorFailAlarm 1.3.6.1.4.1.3373.1103.80.12.1.16
Remote Demodulator Fail Alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioVcoFailAlarm 1.3.6.1.4.1.3373.1103.80.12.1.17
RT VCO fail alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioRxIFAgcAlarm 1.3.6.1.4.1.3373.1103.80.12.1.18
RT Rx IF AGC fail alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioTxIFAgcAlarm 1.3.6.1.4.1.3373.1103.80.12.1.19
RT Tx IF AGC fail alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioIduOduCommunicationAlarm 1.3.6.1.4.1.3373.1103.80.12.1.20
Communication from IDU towards ODU is down
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioOduIduCommunicationAlarm 1.3.6.1.4.1.3373.1103.80.12.1.21
Communication from ODU towards IDU is down
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioLocalOduAlarmSynthesis 1.3.6.1.4.1.3373.1103.80.12.1.22
Local ODU alarm synthesis with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioRemoteOduAlarmSynthesis 1.3.6.1.4.1.3373.1103.80.12.1.23
Local ODU alarm synthesis alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioConfigMismatchAlarm 1.3.6.1.4.1.3373.1103.80.12.1.24
Config Mismatch alarm status with associated severity and related map.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioConfigAlarmReason 1.3.6.1.4.1.3373.1103.80.12.1.25
Bit map to describe the Config Mismatch Alarm
Status: current Access: read-only
OBJECT-TYPE    
  ConfigMismatchReason  

radioRxQualityLowAlarm 1.3.6.1.4.1.3373.1103.80.12.1.26
High BER Alarm status with associated severity.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioRxQualityWarningAlarm 1.3.6.1.4.1.3373.1103.80.12.1.27
The RX signal is close to cause errors on payload.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

radioXpd 1.3.6.1.4.1.3373.1103.80.12.1.28
Cross-Polarization Discrimination, in tenths of dB, is the difference between the received signal power of the co-polarized main beam, and it componemt received on the cross-polarized signal. This object shows an extimated value of the XPD performed by the cross-polarization interference canceller (XPIC). This means that the measure is reliable if: - XPIC is on (linkType is radio2p0Xpic(4), or radio2p2XpicHS(5), or radio2p2XpicFD(6)) - Alarm radioDemodulatorFailAlarm is cleared. - XPD is not too high, since without cross-polar interference the canceller is not able to works well. Basically, in this condition, the extimated XPD is greater than the real one.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioMaintTable 1.3.6.1.4.1.3373.1103.80.13
Table with Command for maintenance of radio branch. Objects in this table is not persistent. An Instance of this table is created on creation of radioBranchEntry
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioMaintEntry

radioMaintEntry 1.3.6.1.4.1.3373.1103.80.13.1
Radio branch Maintenance record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioMaintEntry  

radioTxStatus 1.3.6.1.4.1.3373.1103.80.13.1.1
Transmitter status control. The value transmitterOff(1) is related to a manual operation. The value permanentOff(3) is persistent across restart.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER transmitterOff(1), transmitterOn(2), permanentOff(3)  

radioCarrierOnly 1.3.6.1.4.1.3373.1103.80.13.1.2
Carrier only transmission control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER carrierOnlyOff(1), carrierOnlyOn(2)  

radioLoop 1.3.6.1.4.1.3373.1103.80.13.1.3
Enables/disables the Radio Branch loops.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER loopOff(1), rfLoop(2), iqLoop(3), baseBandLoop(4), rfLoopAtFixedMod(6), baseBandLoopEthSquelch(7), rfLoopAtFixedModEthSquelch(8), iqloopEthSquelch(9)  

radioRFLoopTestResult 1.3.6.1.4.1.3373.1103.80.13.1.4
Radio branch RT loop test result.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER testNone(0), testRunning(1), testNotPossible(2), testPassed(3), testFail(4), testInterrupted(5)  

radioRFLoopTestPercTime 1.3.6.1.4.1.3373.1103.80.13.1.5
Radio branch RT loop test time percentage
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

radioRtPsuOff 1.3.6.1.4.1.3373.1103.80.13.1.6
It switches on/off the Rt power supply
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rtPsuOff(1), rtPsuOn(2)  

radioLom 1.3.6.1.4.1.3373.1103.80.13.1.7
It is used to enable the IP packet forwarding towards Radio.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

radioXpic 1.3.6.1.4.1.3373.1103.80.13.1.8
Enable of the cross polarization interference cancellation of this radio. The value disable is tied to a manual operation (ManOpRecord). This object is applicable only if thiis radio belongs to a 2+0 XPIC or 2+2 XPIC link.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

radioFrequencyTable 1.3.6.1.4.1.3373.1103.80.14
Availables channels for selected channel spacing and modulation (see leaf radioFreqTableSelection).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioFreqEntry

radioFreqTabEntry 1.3.6.1.4.1.3373.1103.80.14.1
RadioFreqTab record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioFreqEntry  

radioFreqChannelId 1.3.6.1.4.1.3373.1103.80.14.1.1
Index of the table
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioFreqChannelNum 1.3.6.1.4.1.3373.1103.80.14.1.2
Available channel number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioFreqValue 1.3.6.1.4.1.3373.1103.80.14.1.3
Frequency related to radioFreqChannelNum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioDuplexFrequencyTable 1.3.6.1.4.1.3373.1103.80.15
Table with available duplex frequencies. Duplex frequency is the absolute value of difference between RX and TX frequency.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioDuplexFreqEntry

radioDuplexFreqEntry 1.3.6.1.4.1.3373.1103.80.15.1
Duplex Frequency entry. There is an entry for each available duplex frequency.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioDuplexFreqEntry  

radioDuplexFreqId 1.3.6.1.4.1.3373.1103.80.15.1.1
Index of the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioDuplexFreqValue 1.3.6.1.4.1.3373.1103.80.15.1.2
Duplex frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioModulationTable 1.3.6.1.4.1.3373.1103.80.16
List of modulations related to channel spacing.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioModulationEntry

radioModulationEntry 1.3.6.1.4.1.3373.1103.80.16.1
radioModulation record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioModulationEntry  

radioChannelSpacing 1.3.6.1.4.1.3373.1103.80.16.1.1
This object identifies the channel spacing.
Status: current Access: read-only
OBJECT-TYPE    
  ChannelSpacing  

radioModulationMap 1.3.6.1.4.1.3373.1103.80.16.1.2
List of modulations in the radioChanSpacing
Status: current Access: read-only
OBJECT-TYPE    
  ModulationMap  

radioRefModulationMap 1.3.6.1.4.1.3373.1103.80.16.1.3
List of modulations that can be selected as reference in the radioChanSpacingId
Status: current Access: read-only
OBJECT-TYPE    
  ModulationMap  

linkStatusTable 1.3.6.1.4.1.3373.1103.80.17
Table with LinkStatusEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkStatusEntry

linkStatusEntry 1.3.6.1.4.1.3373.1103.80.17.1
Link status entry
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkStatusEntry  

linkPolIndex 1.3.6.1.4.1.3373.1103.80.17.1.1
This object identifies the radio polarization. In XPIC radio link identifies one of the polarizations.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

linkAcmRxProfile 1.3.6.1.4.1.3373.1103.80.17.1.2
This object reports the ACM profile number in use in the radio Rx. It is the linkAcmProfileId of linkAcmTable. Label is linkAcmProfileLabel from linkAcmTable
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmTxProfile 1.3.6.1.4.1.3373.1103.80.17.1.3
This object reports the ACM profile number in use in the radio Tx. It is the linkAcmProfileId of linkAcmTable. Label is linkAcmProfileLabel from linkAcmTable
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmRxProfileLabel 1.3.6.1.4.1.3373.1103.80.17.1.4
ASCII string used to describe current acm rx profile
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkAcmTxProfileLabel 1.3.6.1.4.1.3373.1103.80.17.1.5
ASCII string used to describe current acm tx profile
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkAcmRxModulation 1.3.6.1.4.1.3373.1103.80.17.1.6
This object is the type of modulation of the Rx profile in use.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPerSymbol  

linkAcmTxModulation 1.3.6.1.4.1.3373.1103.80.17.1.7
This object is the type of modulation of the Tx profile in use.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPerSymbol  

linkAcmRxCode 1.3.6.1.4.1.3373.1103.80.17.1.8
This object is the type of codificator of the Rx profile in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), normal(1), strong(2)  

linkAcmTxCode 1.3.6.1.4.1.3373.1103.80.17.1.9
This object is the type of codificator of the Tx profile in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), normal(1), strong(2)  

linkTxETHCapacity 1.3.6.1.4.1.3373.1103.80.17.1.10
This object reports (in Kbits/sec) the transmitted payload capacity used by the Ethernet
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkRxETHCapacity 1.3.6.1.4.1.3373.1103.80.17.1.11
This object reports (in Kbits/sec) the received payload capacity used by the Ethernet
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkTxTDMCapacity 1.3.6.1.4.1.3373.1103.80.17.1.12
This object reports the capacity in kbit/sec reserved to TDM tributaries in tx ACM profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkRxTDMCapacity 1.3.6.1.4.1.3373.1103.80.17.1.13
This object reports the capacity in kbit/sec reserved to TDM tributaries in rx ACM profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkRescueModulation 1.3.6.1.4.1.3373.1103.80.17.1.14
This object is the modulation used when the remote terminal is unreachable, ie traffic on radio link is down.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPerSymbol  

linkReducedCapacityAlarm 1.3.6.1.4.1.3373.1103.80.17.1.15
The equipment works in reduced capacity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkLinkTelemetryFailAlarm 1.3.6.1.4.1.3373.1103.80.17.1.16
Fail of link telemetry communication channel with associated Severity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkIdMismatchAlarm 1.3.6.1.4.1.3373.1103.80.17.1.17
Link Identification Alarm with associated Severity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkRadioEocAlarm 1.3.6.1.4.1.3373.1103.80.17.1.18
Fail of Radio Eoc link communication channel with associated Severity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkSetupMismatchAlarm 1.3.6.1.4.1.3373.1103.80.17.1.19
The local setup doesn't match the setup of remote terminal
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkRescueSetupAlarm 1.3.6.1.4.1.3373.1103.80.17.1.20
The equipment is using the setup relative to the rescue modulation
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkXpicProcedureBlockAlarm 1.3.6.1.4.1.3373.1103.80.17.1.21
Only for XPIC equipment configurations. Equipment Controller XPIC procedure Alarm control with associated Severity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkXpicRemTxOffAlarm 1.3.6.1.4.1.3373.1103.80.17.1.22
Only for XPIC equipment configurations. Remote TX OFF command with associated Severity
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkRemoteIduAlarmSynthesis 1.3.6.1.4.1.3373.1103.80.17.1.23
Synthesis of the remote IDU alarms
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkNotMatchingRadiosAlarm 1.3.6.1.4.1.3373.1103.80.17.1.24
Radios of the link does not have matched parameters.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkConfigurationInProgress 1.3.6.1.4.1.3373.1103.80.17.1.25
The link is being configured and the table linkSettingsTable is not available for modifying parameters.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cleared(1), active(2)  

linkXpd 1.3.6.1.4.1.3373.1103.80.17.1.26
Cross-Polarization Discrimination, in tenths of dB, is the difference between the received signal power of the co-polarized main beam, and it componemt received on the cross-polarized signal. This object shows an extimated value of the XPD performed by the cross-polarization interference canceller (XPIC). This means that the measure is reliable if: - XPIC is on (linkType is radio2p0Xpic(4), or radio2p2XpicHS(5), or radio2p2XpicFD(6)) - Alarm radioDemodulatorFailAlarm is cleared. - XPD is not too high, since without cross-polar interference the canceller is not able to works well. Basically, in this condition, the extimated XPD is greater than the real one.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkTfcTable 1.3.6.1.4.1.3373.1103.80.18
Transmitter Fail Check feature. In 1+1 HS configuration, the radio terminal that doesn't receive signals on both receivers, requests the remote transmitter switch. This table was deprecated and replaced by linkTfcV2Table. It is a view of the rows of the linkTfcV2Table with the same linkIndex and linkPolIndex equal to 1, in order to ensure compatibility with old SNMP managers.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkTfcEntry

linkTfcEntry 1.3.6.1.4.1.3373.1103.80.18.1
Radio link TFC entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkTfcEntry  

linkTfcAction 1.3.6.1.4.1.3373.1103.80.18.1.1
reset: to clear the forced switch generated by Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER notActive(0), reset(1)  

linkTfcControl 1.3.6.1.4.1.3373.1103.80.18.1.2
It enables the Tx switch from remote equipment (only if 1+1 configuration and ISO system).
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkTfcWatchWindow 1.3.6.1.4.1.3373.1103.80.18.1.3
Watch Window (in seconds) related to Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 1..300  

linkTfcAlarmThreshold 1.3.6.1.4.1.3373.1103.80.18.1.4
Alarm Threshold (number of seconds with both remote RX in fail) related to Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 1..60  

linkTfcAlarm 1.3.6.1.4.1.3373.1103.80.18.1.5
Transmission switch alarm generated by Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: deprecated Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkTfcRowStatus 1.3.6.1.4.1.3373.1103.80.18.1.6
Status of this conceptual row in linkTfcTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

linkMaintTable 1.3.6.1.4.1.3373.1103.80.19
Table with commands for maintenance of radio link. Objects in this table is not persistent. An Instance of this table is created on creation of linkStatusEntry
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkMaintEntry

linkMaintEntry 1.3.6.1.4.1.3373.1103.80.19.1
Radio link maintenance entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkMaintEntry  

linkBerStart 1.3.6.1.4.1.3373.1103.80.19.1.1
Stop, Start (resetting errors and counters) the pattern. This item is linked to a manual operation (ManOpRecord) instance.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER restart(1), stop(2)  

linkBaseBandLom 1.3.6.1.4.1.3373.1103.80.19.1.2
It is used to enable the IP packet forwarding towards modems. This item is linked to a manual operation (ManOpRecord) instance.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkFadeMarginMeasure 1.3.6.1.4.1.3373.1103.80.19.1.3
Set by manager to start/stop fade margin measure. This item is linked to a manual operation (ManOpRecord) instance. This object is deprecated and replaced by fadeMarginMeasure.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkXpicControlProcedureReset 1.3.6.1.4.1.3373.1103.80.19.1.4
Set by manager to reset the XPIC control procedure after a blocking action.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notActive(0), reset(1)  

linkBerTable 1.3.6.1.4.1.3373.1103.80.20
Table with Command to estimate BER of radio equipment. Every objects in this table is not persistent. An Instance of this table is created on creation of linkStatusEntry
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkBerEntry

linkBerEntry 1.3.6.1.4.1.3373.1103.80.20.1
Radio equipment BER estimate record.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkBerEntry  

linkBerErrorCounterH 1.3.6.1.4.1.3373.1103.80.20.1.1
High 32 bit part of the 64 bit error counter. Bit 32-63.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkBerErrorCounterL 1.3.6.1.4.1.3373.1103.80.20.1.2
Low 32 bit part of the 64 bit error counter. Bit 0-31.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkBerDataCounterH 1.3.6.1.4.1.3373.1103.80.20.1.3
High 32 bit part of the 64 bit data counter. Bit 32-63.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkBerDataCounterL 1.3.6.1.4.1.3373.1103.80.20.1.4
Low 32 bit part of the 64 bit data counter. Bit 0-31.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkBerSyncLossAlarm 1.3.6.1.4.1.3373.1103.80.20.1.5
BER sync loss alarm.
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkBerSyncLossAlarmCounter 1.3.6.1.4.1.3373.1103.80.20.1.6
BER sync loss events counter.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkBerElapsedTime 1.3.6.1.4.1.3373.1103.80.20.1.7
BER measure elapsed time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmTable 1.3.6.1.4.1.3373.1103.80.21
Table with link records.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkAcmEntry

linkAcmEntry 1.3.6.1.4.1.3373.1103.80.21.1
ACM entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkAcmEntry  

linkAcmProfileId 1.3.6.1.4.1.3373.1103.80.21.1.1
This object identifies the profile number for the radio selected by the object linkAcmId.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmProfileModulation 1.3.6.1.4.1.3373.1103.80.21.1.2
This object is the modulation of the profile.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPerSymbol  

linkAcmProfileCode 1.3.6.1.4.1.3373.1103.80.21.1.3
This object is the type of codificator of the profile.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), strong(2)  

linkAcmProfileCapacity 1.3.6.1.4.1.3373.1103.80.21.1.4
This object is used to contain total capacity of profile (in kbits/sec).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmProfileLabel 1.3.6.1.4.1.3373.1103.80.21.1.5
ASCII string used to assign a name to profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

linkAcmProfileEnable 1.3.6.1.4.1.3373.1103.80.21.1.6
The object is used to contain if the use of this profile is enabled or disabled
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkAcmMaxTDMCapacity 1.3.6.1.4.1.3373.1103.80.21.1.7
This object reports the maximum capacity that can be assigned to the TDM traffic. The capacity is specified in number of E1 (2Mbit/s). This object has been superseded by linkE1vsSTM1CapacityTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmPowerScaling 1.3.6.1.4.1.3373.1103.80.21.1.8
This object contains the difference (in eighth of dB) between the TX power at this profile modulation and the TX power at the reference modulation. The power scaling value is achieved from the table linkPtxProfileTable. This object is deprecated: see combinedRadioPowerScalingTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmDownshiftThreshold 1.3.6.1.4.1.3373.1103.80.21.1.9
The object is used to contain the downshift threshold in dB/10.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmUpshiftThreshold 1.3.6.1.4.1.3373.1103.80.21.1.10
The object is used to contain the upshift threshold in dB/10.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmActiveProfile 1.3.6.1.4.1.3373.1103.80.21.1.11
This object is used to contain the active status of this profile. The value of the object is related to linkAcmRxProfile and linkAcmTxProfile of the LinkStatusEntry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cleared(1), activeRx(2), activeTx(3), activeBoth(4)  

linkAcmTDMCapacity 1.3.6.1.4.1.3373.1103.80.21.1.12
This object reports current TDM capacity (in kbits/sec) of the profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmETHCapacity 1.3.6.1.4.1.3373.1103.80.21.1.13
This object reports current ETH capacity (in Kbits/sec) of the profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmAtpcRxPowerScaling 1.3.6.1.4.1.3373.1103.80.21.1.14
This object contains the difference (in eighth of dB) between the ATPC RX level thresholds at this profile modulation and the ATPC RX level thresholds at the upper modulation. This object is deprecated: see combinedRadioPowerScalingTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkAcmPowerRange 1.3.6.1.4.1.3373.1103.80.21.1.15
This object contains (in dB) the current value of ATPC range. This object is deprecated: see combinedRadioPowerScalingTable.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkProTable 1.3.6.1.4.1.3373.1103.80.22
A list of protection link entries. This table was deprecated and replaced by linkProV2Table. It is a view of the rows of the linkProV2Table with the same linkIndex and linkPolIndex equal to 1, in order to ensure compatibility with old SNMP managers
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkProEntry

linkProEntry 1.3.6.1.4.1.3373.1103.80.22.1
An entry containing management information applicable to a protected link.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkProEntry  

linkProProtectionTxChIdx 1.3.6.1.4.1.3373.1103.80.22.1.1
This object identifies the tx protection channel of a protected link. This object is not applicable in case of not-revertive protection. For N+1 links a value different from zero must be set.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

linkProProtectionRxChIdx 1.3.6.1.4.1.3373.1103.80.22.1.2
This object identifies the rx protection channel of a protected link. This object is not applicable in case of not-revertive protection. For N+1 links a value different from zero must be set.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Integer32  

linkProTxWtrTime 1.3.6.1.4.1.3373.1103.80.22.1.3
It defines the Wait Time (in minutes) to Restore in transmission when revertive protection is enabled. Zero value means no switch. If switch is not supported or protection is not revertive, a value different from zero cannot be set.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 0..12  

linkProRxWtrTime 1.3.6.1.4.1.3373.1103.80.22.1.4
It defines the Wait Time (in minutes) to Restore in reception when revertive protection is enabled. Zero value means no switch. If switch is not supported or protection is not revertive, a value different from zero cannot be set.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER 0..12  

linkProTxSwitchedChIdx 1.3.6.1.4.1.3373.1103.80.22.1.5
This object reports the index of tx channel switched to protection. This object is applicable only for N+1 protection schema.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkProRxSwitchedChIdx 1.3.6.1.4.1.3373.1103.80.22.1.6
This object reports the index of rx channel switched to protection. This object is applicable only for N+1 protection schema.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkProTxRevertive 1.3.6.1.4.1.3373.1103.80.22.1.7
It defines if tx protection is revertive or not revertive. In case of N+1 protection, protection is always revertive.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProRxRevertive 1.3.6.1.4.1.3373.1103.80.22.1.8
It defines if rx protection is revertive or not revertive. In case of N+1 protection, protection is always revertive.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProExtraTraffic 1.3.6.1.4.1.3373.1103.80.22.1.9
This object enables or disables the transfer of extra traffic on the protection channel in a N+1 link. This object must be set to disabled in case of architectures different for N+1.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProRowStatus 1.3.6.1.4.1.3373.1103.80.22.1.10
Status of this conceptual row in linkProTable.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

linkProMaintTable 1.3.6.1.4.1.3373.1103.80.23
A list of maintenance commands for protected links. A row in this table is added on creation of a row in linkProTable. This table was deprecated and replaced by linkProMaintV2Table. It is a view of the rows of the linkProMaintV2Table with the same linkIndex and linkPolIndex equal to 1, in order to ensure compatibility with old SNMP managers
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkProMaintEntry

linkProMaintEntry 1.3.6.1.4.1.3373.1103.80.23.1
An entry containing maintenance commands applicable to a protected link.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkProMaintEntry  

linkProMaintTxLockout 1.3.6.1.4.1.3373.1103.80.23.1.1
Command to enable/disable tx lockout. This object is applicable only in case of N+1 protections.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProMaintRxLockout 1.3.6.1.4.1.3373.1103.80.23.1.2
Command to enable/disable rx lockout. This object is applicable only in case of N+1 protections.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProMaintTxForced 1.3.6.1.4.1.3373.1103.80.23.1.3
Command to force switch to a given transmission channel. Zero value means no switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

linkProMaintRxForced 1.3.6.1.4.1.3373.1103.80.23.1.4
Command to force switch to a given receiving channel. Zero value means no switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32  

linkProMaintTxWtrReset 1.3.6.1.4.1.3373.1103.80.23.1.5
Clear wait time to restore making the revertive path immediately available.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER notActive(1), on(2)  

linkProMaintRxWtrReset 1.3.6.1.4.1.3373.1103.80.23.1.6
Clear wait time to restore making the revertive path immediately available.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER notActive(1), on(2)  

linkCapabilitiesTable 1.3.6.1.4.1.3373.1103.80.24
Table with RadioCapabilities entries: there is an entry for each linkTable row. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios. In 1+1 FD radio link, managers have to know the capabilities of each channel. As such, this table is declared deprecated and replaced by combinedRadioCapabilitiesTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkCapabilitiesEntry

linkCapabilitiesEntry 1.3.6.1.4.1.3373.1103.80.24.1
LinkCapabilities entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkCapabilitiesEntry  

linkCapabilitiesCapability 1.3.6.1.4.1.3373.1103.80.24.1.1
Bit map to describe the radio features.
Status: deprecated Access: read-only
OBJECT-TYPE    
  RadioCapability  

linkCapabilitiesTxMinFrequency 1.3.6.1.4.1.3373.1103.80.24.1.2
Minimum of available channel frequency in KHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkCapabilitiesTxMaxFrequency 1.3.6.1.4.1.3373.1103.80.24.1.3
Maximum of available channel frequency in KHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkCapabilitiesStepFrequency 1.3.6.1.4.1.3373.1103.80.24.1.4
Minimum frequency step in KHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkCapabilitiesMinPtxNominalValue 1.3.6.1.4.1.3373.1103.80.24.1.5
Minimum nominal Ptx in dBm.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkCapabilitiesMaxPtxNominalValue 1.3.6.1.4.1.3373.1103.80.24.1.6
Maximum nominal Ptx in dBm.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkCapabilitiesExtendedMinPwr 1.3.6.1.4.1.3373.1103.80.24.1.7
Minimum extended Ptx power for fade margin.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkFrequencyTable 1.3.6.1.4.1.3373.1103.80.25
Availables channels for selected channel spacing and modulation In 1+1 HS and XPIC radio links, this table contains only values supported by both radios. In 1+1 FD radio link, managers have to know the allowable frequencies of each channel. As such, this table is declared deprecated and replaced by combinedRadioFrequencyTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkFreqEntry

linkFreqTabEntry 1.3.6.1.4.1.3373.1103.80.25.1
LinkFreqTab record.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkFreqEntry  

linkFreqChannelId 1.3.6.1.4.1.3373.1103.80.25.1.1
Index of the table
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkFreqChannelNum 1.3.6.1.4.1.3373.1103.80.25.1.2
Available channel number.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkFreqValue 1.3.6.1.4.1.3373.1103.80.25.1.3
Frequency related to linkFreqChannelNum.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkDuplexFrequencyTable 1.3.6.1.4.1.3373.1103.80.26
Table with available duplex frequencies. Duplex frequency is the absolute value of difference between RX and TX frequency. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios. In 1+1 FD radio link, managers have to know the allowable duplex frequencies of each channel. As such, this table is declared deprecated and replaced by combinedRadioDuplexFrequencyTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkDuplexFreqEntry

linkDuplexFreqEntry 1.3.6.1.4.1.3373.1103.80.26.1
Duplex Frequency entry. For each available duplex frequency
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  LinkDuplexFreqEntry  

linkDuplexFreqId 1.3.6.1.4.1.3373.1103.80.26.1.1
Index of the table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkDuplexFreqValue 1.3.6.1.4.1.3373.1103.80.26.1.2
Duplex frequency in KHz.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

linkModulationTable 1.3.6.1.4.1.3373.1103.80.27
List of modulation related to channel spacing. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkModulationEntry

linkModulationEntry 1.3.6.1.4.1.3373.1103.80.27.1
linkModulation record.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkModulationEntry  

linkChannelSpacing 1.3.6.1.4.1.3373.1103.80.27.1.1
This object identifies the channel spacing.
Status: current Access: read-only
OBJECT-TYPE    
  ChannelSpacing  

linkModulationMap 1.3.6.1.4.1.3373.1103.80.27.1.2
List of modulation in the linkChanSpacing
Status: current Access: read-only
OBJECT-TYPE    
  ModulationMap  

linkRefModulationMap 1.3.6.1.4.1.3373.1103.80.27.1.3
List of modulations that can be selected as reference in the linkChanSpacingId
Status: current Access: read-only
OBJECT-TYPE    
  ModulationMap  

combinedRadioCapabilitiesTable 1.3.6.1.4.1.3373.1103.80.28
Table with RadioCapabilities entries: there is an entry for each radioSettingTable row. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios belonging to the link. In 1+1 FD radio link, managers have to know the allowable duplex frequencies of each channel. As such, this table is declared deprecated and replaced by combinedRadioCapabilitiesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CombinedRadioCapabilitiesEntry

combinedRadioCapabilitiesEntry 1.3.6.1.4.1.3373.1103.80.28.1
combinedRadioCapabilities entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CombinedRadioCapabilitiesEntry  

combinedRadioCapabilitiesCapability 1.3.6.1.4.1.3373.1103.80.28.1.1
Bit map to describe the radio features.
Status: current Access: read-only
OBJECT-TYPE    
  RadioCapability  

combinedRadioCapabilitiesTxMinFrequency 1.3.6.1.4.1.3373.1103.80.28.1.2
Minimum of available channel frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioCapabilitiesTxMaxFrequency 1.3.6.1.4.1.3373.1103.80.28.1.3
Maximum of available channel frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioCapabilitiesStepFrequency 1.3.6.1.4.1.3373.1103.80.28.1.4
Minimum frequency step in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioCapabilitiesMinPtxNominalValue 1.3.6.1.4.1.3373.1103.80.28.1.5
Minimum nominal Ptx in dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioCapabilitiesMaxPtxNominalValue 1.3.6.1.4.1.3373.1103.80.28.1.6
Maximum nominal Ptx in dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioCapabilitiesExtendedMinPwr 1.3.6.1.4.1.3373.1103.80.28.1.7
Minimum extended Ptx power for fade margin.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioFrequencyTable 1.3.6.1.4.1.3373.1103.80.29
Availables channels for selected channel spacing and modulation In 1+1 HS and XPIC radio links, this table contains only values supported by both radios.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CombinedRadioFreqEntry

combinedRadioFreqTabEntry 1.3.6.1.4.1.3373.1103.80.29.1
combinedRadioFreqTab record.
Status: current Access: not-accessible
OBJECT-TYPE    
  CombinedRadioFreqEntry  

combinedRadioFreqChannelId 1.3.6.1.4.1.3373.1103.80.29.1.1
Index of the table
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioFreqChannelNum 1.3.6.1.4.1.3373.1103.80.29.1.2
Available channel number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioFreqValue 1.3.6.1.4.1.3373.1103.80.29.1.3
Frequency related to combinedRadioFreqChannelNum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioDuplexFrequencyTable 1.3.6.1.4.1.3373.1103.80.30
Table with available duplex frequencies. Duplex frequency is the absolute value of difference between RX and TX frequency. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CombinedRadioDuplexFreqEntry

combinedRadioDuplexFreqEntry 1.3.6.1.4.1.3373.1103.80.30.1
Duplex Frequency entry. There is an entry for each available duplex frequency.
Status: current Access: not-accessible
OBJECT-TYPE    
  CombinedRadioDuplexFreqEntry  

combinedRadioDuplexFreqId 1.3.6.1.4.1.3373.1103.80.30.1.1
Index of the table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioDuplexFreqValue 1.3.6.1.4.1.3373.1103.80.30.1.2
Duplex frequency in KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioPowerScalingTable 1.3.6.1.4.1.3373.1103.80.31
List of modulation related to channel spacing. In 1+1 HS and XPIC radio links, this table contains only values supported by both radios.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CombinedRadioPowerScalingEntry

combinedRadioPowerScalingEntry 1.3.6.1.4.1.3373.1103.80.31.1
radioPowerScaling record.
Status: current Access: not-accessible
OBJECT-TYPE    
  CombinedRadioPowerScalingEntry  

combinedRadioPowerScaling 1.3.6.1.4.1.3373.1103.80.31.1.1
This object contains the difference (in eighth of dB) between the TX power at this profile modulation and the TX power at the reference modulation. The power scaling value is achieved from the table linkPtxProfileTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioAtpcRxPowerScaling 1.3.6.1.4.1.3373.1103.80.31.1.2
This object contains the difference (in eighth of dB) between the ATPC RX level thresholds at this profile modulation and the ATPC RX level thresholds at the upper modulation.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

combinedRadioPowerRange 1.3.6.1.4.1.3373.1103.80.31.1.3
This object contains (in dB) the current value of ATPC range.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

stm1BulkMappingTable 1.3.6.1.4.1.3373.1103.80.32
Table with entries containing stm-1 bulk transport parameters for a particular link. For each link are present as many rows as the STM-1 that the link can carry in bulk mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Stm1BulkMappingEntry

stm1BulkMappingEntry 1.3.6.1.4.1.3373.1103.80.32.1
An row in stm1BulkSettingsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Stm1BulkMappingEntry  

stm1BulkPolIndex 1.3.6.1.4.1.3373.1103.80.32.1.1
Polarization index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

stm1BulkChanIndex 1.3.6.1.4.1.3373.1103.80.32.1.2
STM-1 channel index. The range of this object is from 1 to N, where N is the number of STM-1 that a link can carry in bulk mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

stm1BulkChannel 1.3.6.1.4.1.3373.1103.80.32.1.3
Index of the stm-1 in stm1Table. The SNMP agent will accept only index of a STM-1 present in stm1Table with stm1Structure set to opaque(4).
Status: current Access: read-write
OBJECT-TYPE    
  Stm1IndexOrZero  

linkE1vsSTM1CapacityTable 1.3.6.1.4.1.3373.1103.80.33
Table with entries containing the E1 cpacity according to the tributaries STM-1 configured to be carried in bulk mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkE1vsSTM1CapacityEntry

linkE1vsSTM1CapacityEntry 1.3.6.1.4.1.3373.1103.80.33.1
An row in linkE1vsSTM1CapacityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkE1vsSTM1CapacityEntry  

linkE1vsSTM1CapacityStm1 1.3.6.1.4.1.3373.1103.80.33.1.1
Number of tributaries STM-1 configured to be transported in bulk mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

linkE1vsSTM1CapacityE1 1.3.6.1.4.1.3373.1103.80.33.1.2
Number of E1 that can be carried by this profile according to the the tributaries STM-1 carried in bulk mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkTfcV2Table 1.3.6.1.4.1.3373.1103.80.34
Transmitter Fail Check feature. In 1+1 HS configuration, the radio terminal that doesn't receive signals on both receivers, requests the remote transmitter switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkTfcV2Entry

linkTfcV2Entry 1.3.6.1.4.1.3373.1103.80.34.1
Radio link TFC entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkTfcV2Entry  

linkTfcV2Action 1.3.6.1.4.1.3373.1103.80.34.1.1
reset: to clear the forced switch generated by Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notActive(0), reset(1)  

linkTfcV2Control 1.3.6.1.4.1.3373.1103.80.34.1.2
It enables the Tx switch from remote equipment (only if 1+1 configuration and ISO system).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkTfcV2WatchWindow 1.3.6.1.4.1.3373.1103.80.34.1.3
Watch Window (in seconds) related to Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..300  

linkTfcV2AlarmThreshold 1.3.6.1.4.1.3373.1103.80.34.1.4
Alarm Threshold (number of seconds with both remote RX in fail) related to Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..60  

linkTfcV2Alarm 1.3.6.1.4.1.3373.1103.80.34.1.5
Transmission switch alarm generated by Trasmission Fail Check algorithm (only if 1+1 configuration and ISO system).
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkTfcV2RowStatus 1.3.6.1.4.1.3373.1103.80.34.1.6
Status of this conceptual row in linkTfcV2Table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

linkProV2Table 1.3.6.1.4.1.3373.1103.80.35
A list of protection link entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkProV2Entry

linkProV2Entry 1.3.6.1.4.1.3373.1103.80.35.1
An entry containing management information applicable to a protected link.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkProV2Entry  

linkProV2ProtectionTxChIdx 1.3.6.1.4.1.3373.1103.80.35.1.1
This object identifies the tx protection channel of a protected link. This object is not applicable in case of not-revertive protection. For N+1 links a value different from zero must be set.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

linkProV2ProtectionRxChIdx 1.3.6.1.4.1.3373.1103.80.35.1.2
This object identifies the rx protection channel of a protected link. This object is not applicable in case of not-revertive protection. For N+1 links a value different from zero must be set.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

linkProV2TxWtrTime 1.3.6.1.4.1.3373.1103.80.35.1.3
It defines the Wait Time (in minutes) to Restore in transmission when revertive protection is enabled. Zero value means no switch. If switch is not supported or protection is not revertive, a value different from zero cannot be set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..12  

linkProV2RxWtrTime 1.3.6.1.4.1.3373.1103.80.35.1.4
It defines the Wait Time (in minutes) to Restore in reception when revertive protection is enabled. Zero value means no switch. If switch is not supported or protection is not revertive, a value different from zero cannot be set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..12  

linkProV2TxSwitchedChIdx 1.3.6.1.4.1.3373.1103.80.35.1.5
This object reports the index of tx channel switched to protection. This object is applicable only for N+1 protection schema.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkProV2RxSwitchedChIdx 1.3.6.1.4.1.3373.1103.80.35.1.6
This object reports the index of rx channel switched to protection. This object is applicable only for N+1 protection schema.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkProV2TxRevertive 1.3.6.1.4.1.3373.1103.80.35.1.7
It defines if tx protection is revertive or not revertive. In case of N+1 protection, protection is always revertive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProV2RxRevertive 1.3.6.1.4.1.3373.1103.80.35.1.8
It defines if rx protection is revertive or not revertive. In case of N+1 protection, protection is always revertive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProV2ExtraTraffic 1.3.6.1.4.1.3373.1103.80.35.1.9
This object enables or disables the transfer of extra traffic on the protection channel in a N+1 link. This object must be set to disabled in case of architectures different for N+1.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProV2RowStatus 1.3.6.1.4.1.3373.1103.80.35.1.10
Status of this conceptual row in linkProV2Table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

linkProMaintV2Table 1.3.6.1.4.1.3373.1103.80.36
A list of maintenance commands for protected links. A row in this table is added on creation of a row in linkProV2Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkProMaintV2Entry

linkProMaintV2Entry 1.3.6.1.4.1.3373.1103.80.36.1
An entry containing maintenance commands applicable to a protected link.
Status: current Access: not-accessible
OBJECT-TYPE    
  LinkProMaintV2Entry  

linkProMaintV2TxLockout 1.3.6.1.4.1.3373.1103.80.36.1.1
Command to enable/disable tx lockout. This object is applicable only in case of N+1 protections.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProMaintV2RxLockout 1.3.6.1.4.1.3373.1103.80.36.1.2
Command to enable/disable rx lockout. This object is applicable only in case of N+1 protections.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkProMaintV2TxForced 1.3.6.1.4.1.3373.1103.80.36.1.3
Command to force switch to a given transmission channel. Zero value means no switch.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

linkProMaintV2RxForced 1.3.6.1.4.1.3373.1103.80.36.1.4
Command to force switch to a given receiving channel. Zero value means no switch.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

linkProMaintV2TxWtrReset 1.3.6.1.4.1.3373.1103.80.36.1.5
Clear wait time to restore making the revertive path immediately available.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notActive(1), on(2)  

linkProMaintV2RxWtrReset 1.3.6.1.4.1.3373.1103.80.36.1.6
Clear wait time to restore making the revertive path immediately available.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notActive(1), on(2)  

sspTable 1.3.6.1.4.1.3373.1103.80.37
A list of operative and administrative set of parameters. This table holds three row for every link (and its polarizations) configured in the NE: 1) administative parameters of local NE 2) operative parameters of local NE 3) administative parameters of remote NE
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SspEntry

sspEntry 1.3.6.1.4.1.3373.1103.80.37.1
An entry containing SSP relevant parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SspEntry  

sspParameterType 1.3.6.1.4.1.3373.1103.80.37.1.1
This object identifies what parameters are for.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER localAdminStatus(1), localOperStatus(2), remoteAdminStatus(3)  

sspLinkBandwidth 1.3.6.1.4.1.3373.1103.80.37.1.2
Link Bandwidth (channel spacing).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sspBw3p5Mhz(0), sspBw7MHz(1), sspBw14MHz(2), sspBw28MHz(3), sspBw56MHz(4), sspBw10MHz(5), sspBw20MHz(6), sspBw30MHz(7), sspBw40MHz(8), sspBw50MHz(9), sspBw112Mhz(10), sspBw250Mhz(11), sspBw500Mhz(12), sspBw750Mhz(13), sspBw1Ghz(14), sspBw60MHz(15), sspBw80MHz(16)  

sspLinkModulation 1.3.6.1.4.1.3373.1103.80.37.1.3
Link reference modulation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sspModBPSK(1), sspMod4QAM(2), sspMod8PSK(3), sspMod16QAM(4), sspMod32QAM(5), sspMod64QAM(6), sspMod128QAM(7), sspMod256QAM(8), sspMod512QAM(9), sspMod1024QAM(10), sspMod2048QAM(11), sspMod4096QAM(12)  

sspLinkAcmEngineEnable 1.3.6.1.4.1.3373.1103.80.37.1.4
This object is used to enable/disable the ACM engine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

sspLinkTxUpperProfile 1.3.6.1.4.1.3373.1103.80.37.1.5
The object (and linkTxLowerProfile object) is used to restrict the TX profile range when ACM is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sspLinkTxLowerProfile 1.3.6.1.4.1.3373.1103.80.37.1.6
The object (and linkTxUpperProfile object) is used to restrict the TX profile range when ACM is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sspLinkSynchSetupProtocolEnable 1.3.6.1.4.1.3373.1103.80.37.1.7
Synchronization Setup Protocol (SSP) control.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

sspLinkProfilesSetSelection 1.3.6.1.4.1.3373.1103.80.37.1.8
Selection of the working profile set between high gain (max robustness) profile set and high throughput (max capacity) profile set. The set of profiles high gain features a greater robustness against to the set of profiles high throughput. For radio systems that do not have more sets of profiles, this object becomes read only and its reading shows the only one set of profiles supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER highThroughput(1), highGain(2)  

sspTdmE1Channel 1.3.6.1.4.1.3373.1103.80.37.1.9
Number of E1 channels. This object is used to define the capacity of E1 tributaries assigned to a given radio link. The capacity is changed in steps of E1 (2Mbit/s).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sspTdmStm1Channel 1.3.6.1.4.1.3373.1103.80.37.1.10
Number of STM-1 channels transported in bulk mode.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioLoopCapabilityTable 1.3.6.1.4.1.3373.1103.80.38
This table shows which group a radio loop belongs to. Radios with the same group number (identifier) close loop simultaneously.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioLoopCapabilityEntry

radioLoopCapabilityEntry 1.3.6.1.4.1.3373.1103.80.38.1
An entry containing a group identifier for each radio loop type.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioLoopCapabilityEntry  

radioLoopRfGroup 1.3.6.1.4.1.3373.1103.80.38.1.1
The group to which the radio RF loop belong to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioLoopIqGroup 1.3.6.1.4.1.3373.1103.80.38.1.2
The group to which the radio IQ loop belong to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioLoopBaseBandGroup 1.3.6.1.4.1.3373.1103.80.38.1.3
The group to which the radio base loop belong to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioRxBerThresholdTable 1.3.6.1.4.1.3373.1103.80.39
This table shows the nominal and measured values of RX power at a bit error rate (BER) equal to 10e-6.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadioRxBerThresholdEntry

radioRxBerThresholdEntry 1.3.6.1.4.1.3373.1103.80.39.1
An entry containing the RX power thresholds.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadioRxBerThresholdEntry  

radioRxBerThresholdStatus 1.3.6.1.4.1.3373.1103.80.39.1.1
This object shows whether the following objects are significant.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonValid(1), valid(2)  

radioNominalRxBerThreshold 1.3.6.1.4.1.3373.1103.80.39.1.2
The nominal value of RX power @ BER equal to 10e-6
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioMeasuredRxBerThreshold 1.3.6.1.4.1.3373.1103.80.39.1.3
The measured value of RX power @ BER equal to 10e-6.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

radioRemDemodulatorFailAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.50
Defines the severity associated to the radioRemDemodulatorFailAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioRxActiveStatusTrapNotification 1.3.6.1.4.1.3373.1103.80.51
Enable/disables (statusTrapEnable or statusTrapDisable) the trap generation on status change event for radioRxActivestatus
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trapDisable(1), trapEnable(2)  

radioTxActiveStatusTrapNotification 1.3.6.1.4.1.3373.1103.80.52
Define the severity associated to the radioTxActivestatus and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trapDisable(1), trapEnable(2)  

radioCableOpenAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.53
Defines the severity associated to the radioCableOpen and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioCableShortAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.54
Defines the severity associated to the radioCableShort and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioInvalidFrequencyAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.55
Defines the severity associated to the radioInvalidFrequencyAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioBaseBandRxAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.56
Defines the severity associated to the radioBaseBandRxAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioModulatorFailAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.57
Defines the severity associated to the radioModulatorFailAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioDemodulatorFailAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.58
Defines the severity associated to the radioDemodulatorFailAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioRxPowerLowAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.59
Defines the severity associated to the radioRxPowerLowAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioTxPowerLowAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.60
Defines the severity associated to the radioTxPowerLowAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioVcoFailAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.61
Defines the severity associated to the radioVcoFailAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioRxIFAgcAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.62
Defines the severity associated to the radioRxIFAgcAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioTxIFAgcAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.63
Defines the severity associated to the radioTxIFAgcAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioIduOduCommunicationAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.64
Define the severity associated to the radioIduOduCommunicationAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioOduIduCommunicationAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.65
Define the severity associated to the radioOduIduCommunicationAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioLocalOduAlarmSynthesisSeverityCode 1.3.6.1.4.1.3373.1103.80.66
Define the severity associated to the radioLocalOduAlarmSynthesis and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioRemoteOduAlarmSynthesisSeverityCode 1.3.6.1.4.1.3373.1103.80.67
Define the severity associated to the radioRemoteOduAlarmSynthesis and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioConfigMismatchAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.68
Defines the severity associated to the radioConfigMismatchAlarm and enables/disables the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioPrxHysteresisValue 1.3.6.1.4.1.3373.1103.80.69
Defines the delta value associated to the radioPrx before having a new trap generation (radioPtxChange TRAP). The zero value is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radioPtxHysteresisValue 1.3.6.1.4.1.3373.1103.80.70
Defines the delta value associated to the radioPtx before having a new trap generation (radioPtxChange TRAP). The zero value is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radioPrxHysteresisValueTrapNotification 1.3.6.1.4.1.3373.1103.80.71
Enables/disables the Rx change trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trapDisable(1), trapEnable(2)  

radioPtxHysteresisValueTrapNotification 1.3.6.1.4.1.3373.1103.80.72
Enables/disables the Tx change trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trapDisable(1), trapEnable(2)  

radioRxQualityLowAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.73
Define the severity associated to the radioRxQualityLowAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

radioRxQualityWarningAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.74
Define the severity associated to the radioRxQualityWarningAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkReducedCapacityAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.75
Define the severity associated to the linkReducedCapacityAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkLinkTelemetryFailAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.76
Define the severity associated to the linkLinkTelemetryFailAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkIdMismatchAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.77
Define the severity associated to the linkIdMismatchAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkRadioEocAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.78
Define the severity associated to the linkRadioEocAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkSetupMismatchAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.79
Define the severity associated to the linkSetupMismatchAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkRescueSetupAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.80
Define the severity associated to the linkRescueSetupAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkXpicProcedureBlockAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.81
Define the severity associated to the linkXpicProcedureBlockAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkXpicRemTxOffAlarmAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.82
Define the severity associated to the linkXpicRemTxOffAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkLocalIduAlarmSynthesis 1.3.6.1.4.1.3373.1103.80.83
Synthesis of the local IDU alarms
Status: current Access: read-only
OBJECT-TYPE    
  AlarmStatus  

linkLocalIduAlarmSynthesisSeverityCode 1.3.6.1.4.1.3373.1103.80.84
Define the severity associated to the linkLocalIduAlarmSynthesis and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkRemoteIduAlarmSynthesisSeverityCode 1.3.6.1.4.1.3373.1103.80.85
Define the severity associated to the linkLocalIduAlarmSynthesis and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkTfcAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.86
Define the severity associated to the linkTfcV2Alarm (linkTfcAlarm) and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkBerSyncLossAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.87
Define the severity associated to the linkBerSyncLossAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

linkNotMatchingRadiosAlarmSeverityCode 1.3.6.1.4.1.3373.1103.80.88
Define the severity associated to the linkNotMatchingRadiosAlarm and enable/disable the trap generation on status change event.
Status: current Access: read-write
OBJECT-TYPE    
  AlarmSeverityCode  

channelSpacingSelection 0.1.1.3.6.1.4.1.3373.1103.80.89
his object selects which channel spacings the radio link has to support: - etsi: Compliant with European Telecommunication Standards Institute - fcc: Compliant with Federal Communications Commission
Status: current Access: read-write
OBJECT-TYPE    
  BITS etsi(0), fcc(1)  

fadeMarginMeasure 1.3.6.1.4.1.3373.1103.80.90
Set by manager to start/stop fade margin measure. This item is linked to a manual operation (ManOpRecord) instance.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

linkConfigurationInProgressTrapNotification 1.3.6.1.4.1.3373.1103.80.91
Enable/disables (statusTrapEnable or statusTrapDisable) the trap generation on status change event for linkConfigurationInProgress
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trapDisable(1), trapEnable(2)  

radioPrxChange 1.3.6.1.4.1.3373.1103.0.8001
This event is generated when radioPrx is changed, in modulus, more than radioPtxHysteresisValue from last TRAP. The data passed with the event are: 1) equipIpSnmpAgentAddress - agent IP address 2) radioIndex - branch index 3) radioName - user assinged name 4) radioPrx - PRX value
Status: current Access: read-write
NOTIFICATION-TYPE    

radioPtxChange 1.3.6.1.4.1.3373.1103.0.8002
This event is generated when radioPtx is changed, in modulus, more than radioPtxHysteresisValue from last TRAP. The data passed with the event are: 1) equipIpSnmpAgentAddress - agent IP address 2) radioIndex - branch index 3) radioName - user assigned name 4) radioPtx - PTX value
Status: current Access: read-write
NOTIFICATION-TYPE