SIXNET-MIB

File: SIXNET-MIB.mib (542861 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
Q-BRIDGE-MIB P-BRIDGE-MIB BRIDGE-MIB
INET-ADDRESS-MIB IEEE8021-PAE-MIB IF-MIB

Imported symbols

Integer32 MODULE-IDENTITY OBJECT-TYPE
enterprises TimeTicks Counter32
Unsigned32 IpAddress NOTIFICATION-TYPE
MODULE-COMPLIANCE OBJECT-GROUP TEXTUAL-CONVENTION
TruthValue PortList VlanIndex
DisplayString RowStatus EnabledStatus
BridgeId Timeout dot1dStpPortEntry
MacAddress InetAddressType InetAddress
dot1xAuthConfigEntry ifIndex InterfaceIndex

Defined Types

SixnetDiscrete  
A discrete input or output value which may be turned on or off or may have an unknown state.
TEXTUAL-CONVENTION    
  INTEGER off(0), on(1), unknown(2)  

PppEntry  
SEQUENCE    
  pppifIndex InterfaceIndex
  pppifOperStatus INTEGER

SxRingIndex  
A unique value, greater than zero, identifying a ring in which this switch participates.
TEXTUAL-CONVENTION    
  Integer32 1..2147483647  

SxRingEntry  
SEQUENCE    
  sxRingIndex SxRingIndex
  sxRingName DisplayString
  sxRingGood TruthValue
  sxRingPrimarySeen TruthValue
  sxRingBackupSeen TruthValue
  sxRingPrimaryIf InterfaceIndex
  sxRingBackupIf InterfaceIndex

FirmwareEntry  
SEQUENCE    
  firmwareIndex INTEGER
  firmwareDefault INTEGER
  firmwareRunning INTEGER
  firmwareVersion OCTET STRING
  firmwareHealth INTEGER

KeySegment  
The total length of the key is 1024 characters, it is divided into 8 parts and stored in 8 separated mib variables as below: Key1: part 1 of the key (1-128) Key2: part 2 of the key (129-256) Key3: part 3 of the key (257-384) Key4: part 4 of the key (385-512) Key5: part 5 of the key (513-640) Key6: part 6 of the key (641-768) Key7: part 7 of the key (769-896) Key8: part 8 of the key (897-1024) Please note that if the key string is less then 1024 characters, the remaining part of the string will be filled by a zero-length string. For example, if the length of the key is 129, we will get a string of length 128 in Key1, and a string of length 1 in Key2, moreover, Key3 to Key8 will all be zero-length strings.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..128)  

ValidStatus  
A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destroys an entry.
TEXTUAL-CONVENTION    
  INTEGER valid(1), invalid(2)  

StaPathCostMode  
The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost as a 32 bit value.
TEXTUAL-CONVENTION    
  INTEGER short(1), long(2)  

SwitchInfoEntry  
SEQUENCE    
  swUnitIndex Unsigned32
  swHardwareVer DisplayString
  swMicrocodeVer DisplayString
  swLoaderVer DisplayString
  swBootRomVer DisplayString
  swOpCodeVer DisplayString
  swPortNumber Integer32
  swPowerStatus INTEGER
  swRoleInSystem INTEGER
  swSerialNumber DisplayString
  swServiceTag DisplayString
  swModelNumber DisplayString
  swEpldVer DisplayString

SwitchIndivPowerEntry  
SEQUENCE    
  swIndivPowerUnitIndex Unsigned32
  swIndivPowerIndex INTEGER
  swIndivPowerStatus INTEGER

PortEntry  
SEQUENCE    
  portIndex Unsigned32
  portName DisplayString
  portType INTEGER
  portSpeedDpxCfg INTEGER
  portFlowCtrlCfg INTEGER
  portCapabilities BITS
  portAutonegotiation EnabledStatus
  portSpeedDpxStatus INTEGER
  portFlowCtrlStatus INTEGER
  portTrunkIndex Integer32
  portComboForcedMode INTEGER
  portMasterSlaveModeCfg INTEGER

TrunkEntry  
SEQUENCE    
  trunkIndex Unsigned32
  trunkPorts PortList
  trunkCreation INTEGER
  trunkStatus ValidStatus

LacpPortEntry  
SEQUENCE    
  lacpPortIndex Unsigned32
  lacpPortStatus EnabledStatus

StaPortEntry  
SEQUENCE    
  staPortFastForward EnabledStatus
  staPortProtocolMigration TruthValue
  staPortOperEdgePort TruthValue
  staPortAdminPointToPoint INTEGER
  staPortOperPointToPoint TruthValue
  staPortSystemStatus EnabledStatus
  staPortLongAdminPathCost Integer32
  staPortLongOperPathCost Integer32
  staPortRootGuardAdminStatus EnabledStatus
  staPortRootGuardOperStatus EnabledStatus
  staPortBpduGuard EnabledStatus
  staPortAdminEdgePortWithAuto INTEGER
  staPortBpduFilter EnabledStatus

XstInstanceCfgEntry  
SEQUENCE    
  xstInstanceCfgIndex Integer32
  xstInstanceCfgPriority Integer32
  xstInstanceCfgTimeSinceTopologyChange TimeTicks
  xstInstanceCfgTopChanges Integer32
  xstInstanceCfgDesignatedRoot BridgeId
  xstInstanceCfgRootCost Integer32
  xstInstanceCfgRootPort Integer32
  xstInstanceCfgMaxAge Timeout
  xstInstanceCfgHelloTime Timeout
  xstInstanceCfgHoldTime Timeout
  xstInstanceCfgForwardDelay Timeout
  xstInstanceCfgBridgeMaxAge Timeout
  xstInstanceCfgBridgeHelloTime Timeout
  xstInstanceCfgBridgeForwardDelay Timeout
  xstInstanceCfgTxHoldCount Integer32
  xstInstanceCfgPathCostMethod StaPathCostMode

XstInstancePortEntry  
SEQUENCE    
  xstInstancePortInstance Unsigned32
  xstInstancePortPort Unsigned32
  xstInstancePortPriority Integer32
  xstInstancePortState INTEGER
  xstInstancePortEnable EnabledStatus
  xstInstancePortPathCost Integer32
  xstInstancePortDesignatedRoot BridgeId
  xstInstancePortDesignatedCost Integer32
  xstInstancePortDesignatedBridge BridgeId
  xstInstancePortDesignatedPort OCTET STRING
  xstInstancePortForwardTransitions Counter32
  xstInstancePortPortRole INTEGER
  xstInstancePortAdminPathCost Integer32
  xstInstancePortOperPathCost Integer32

MstInstanceEditEntry  
SEQUENCE    
  mstInstanceEditIndex Integer32
  mstInstanceEditVlansMap OCTET STRING
  mstInstanceEditVlansMap2k OCTET STRING
  mstInstanceEditVlansMap3k OCTET STRING
  mstInstanceEditVlansMap4k OCTET STRING
  mstInstanceEditRemainingHops Integer32

MstInstanceOperEntry  
SEQUENCE    
  mstInstanceOperIndex Integer32
  mstInstanceOperVlansMap OCTET STRING
  mstInstanceOperVlansMap2k OCTET STRING
  mstInstanceOperVlansMap3k OCTET STRING
  mstInstanceOperVlansMap4k OCTET STRING

StaLoopbackDetectionPortEntry  
SEQUENCE    
  staLoopbackDetectionPortIfIndex InterfaceIndex
  staLoopbackDetectionPortStatus EnabledStatus
  staLoopbackDetectionPortTrapStatus EnabledStatus
  staLoopbackDetectionPortReleaseMode INTEGER
  staLoopbackDetectionPortRelease INTEGER

MirrorEntry  
SEQUENCE    
  mirrorDestinationPort Unsigned32
  mirrorSourcePort Unsigned32
  mirrorType INTEGER
  mirrorStatus ValidStatus

VlanMirrorEntry  
SEQUENCE    
  vlanMirrorDestinationPort Unsigned32
  vlanMirrorSourceVlan Unsigned32
  vlanMirrorStatus ValidStatus

IgmpSnoopRouterCurrentEntry  
SEQUENCE    
  igmpSnoopRouterCurrentVlanIndex Unsigned32
  igmpSnoopRouterCurrentPorts PortList
  igmpSnoopRouterCurrentStatus PortList

IgmpSnoopRouterStaticEntry  
SEQUENCE    
  igmpSnoopRouterStaticVlanIndex Unsigned32
  igmpSnoopRouterStaticPorts PortList
  igmpSnoopRouterStaticStatus ValidStatus

IgmpSnoopMulticastCurrentEntry  
SEQUENCE    
  igmpSnoopMulticastCurrentVlanIndex Unsigned32
  igmpSnoopMulticastCurrentIpAddress IpAddress
  igmpSnoopMulticastCurrentPorts PortList
  igmpSnoopMulticastCurrentStatus PortList

IgmpSnoopMulticastStaticEntry  
SEQUENCE    
  igmpSnoopMulticastStaticVlanIndex Unsigned32
  igmpSnoopMulticastStaticIpAddress IpAddress
  igmpSnoopMulticastStaticPorts PortList
  igmpSnoopMulticastStaticStatus ValidStatus

IgmpSnoopCurrentVlanEntry  
SEQUENCE    
  igmpSnoopCurrentVlanIndex Unsigned32
  igmpSnoopCurrentVlanImmediateLeave EnabledStatus

IgmpSnoopProfileEntry  
SEQUENCE    
  igmpSnoopProfileId Unsigned32
  igmpSnoopProfileAction INTEGER
  igmpSnoopProfileStatus ValidStatus

IgmpSnoopProfileRangeEntry  
SEQUENCE    
  igmpSnoopProfileRangeProfileId Unsigned32
  igmpSnoopProfileRangeInetAddressType InetAddressType
  igmpSnoopProfileRangeStartInetAddress InetAddress
  igmpSnoopProfileRangeEndInetAddress InetAddress
  igmpSnoopProfileRangeAction INTEGER

IgmpSnoopFilterPortEntry  
SEQUENCE    
  igmpSnoopFilterPortIndex Unsigned32
  igmpSnoopFilterPortProfileId Integer32

IgmpSnoopThrottlePortEntry  
SEQUENCE    
  igmpSnoopThrottlePortIndex Unsigned32
  igmpSnoopThrottlePortRunningStatus TruthValue
  igmpSnoopThrottlePortAction INTEGER
  igmpSnoopThrottlePortMaxGroups Integer32
  igmpSnoopThrottlePortCurrentGroups Integer32

NetConfigEntry  
SEQUENCE    
  netConfigIfIndex Unsigned32
  netConfigIPAddress IpAddress
  netConfigSubnetMask IpAddress
  netConfigPrimaryInterface INTEGER
  netConfigUnnumbered INTEGER
  netConfigStatus RowStatus

DhcpcInterfaceEntry  
SEQUENCE    
  dhcpcIfIndex Unsigned32
  dhcpcIfClientIdMode INTEGER
  dhcpcIfClientId OCTET STRING

VlanEntry  
SEQUENCE    
  vlanIndex Unsigned32
  vlanAddressMethod INTEGER

VlanPortEntry  
SEQUENCE    
  vlanPortIndex Unsigned32
  vlanPortMode INTEGER
  vlanPortPrivateVlanType INTEGER

ProtocolVlanEntry  
SEQUENCE    
  protocolVlanGroupId Unsigned32
  protocolVlanGroupVid Integer32

VlanDot1qTunnelPortEntry  
SEQUENCE    
  vlanDot1qTunnelPortIndex Unsigned32
  vlanDot1qTunnelPortMode INTEGER
  vlanDot1qTunnelPortEtherType Unsigned32

VoiceVlanOuiEntry  
SEQUENCE    
  voiceVlanOuiAddress MacAddress
  voiceVlanOuiMask MacAddress
  voiceVlanOuiDescription DisplayString
  voiceVlanOuiStatus ValidStatus

VoiceVlanPortEntry  
SEQUENCE    
  voiceVlanPortIfIndex Integer32
  voiceVlanPortMode INTEGER
  voiceVlanPortSecurity EnabledStatus
  voiceVlanPortPriority Integer32
  voiceVlanPortRuleOui EnabledStatus
  voiceVlanPortRuleLldp EnabledStatus

MacVlanEntry  
SEQUENCE    
  macVlanMacAddress MacAddress
  macVlanId Integer32
  macVlanStatus ValidStatus

SubnetVlanEntry  
SEQUENCE    
  subnetVlanIpAddress IpAddress
  subnetVlanMask IpAddress
  subnetVlanId Integer32
  subnetVlanPriority Integer32
  subnetVlanStatus ValidStatus

PrioIpDscpEntry  
SEQUENCE    
  prioIpDscpPort Unsigned32
  prioIpDscpValue Integer32
  prioIpDscpCos Integer32

PrioWrrEntry  
SEQUENCE    
  prioWrrTrafficClass Integer32
  prioWrrWeight Integer32

TrapDestEntry  
SEQUENCE    
  trapDestAddress IpAddress
  trapDestCommunity OCTET STRING
  trapDestStatus ValidStatus
  trapDestVersion INTEGER
  trapDestUdpPort Integer32

RateLimitPortEntry  
SEQUENCE    
  rlPortIndex Unsigned32
  rlPortInputStatus EnabledStatus
  rlPortOutputStatus EnabledStatus
  rlPortInputLimitInKilo Integer32
  rlPortOutputLimitInKilo Integer32

DiffServPortEntry  
SEQUENCE    
  diffServPortIfIndex Unsigned32
  diffServPortPolicyMapIndex Integer32
  diffServPortIngressIpAclIndex Integer32
  diffServPortIngressMacAclIndex Integer32
  diffServPortIngressIpv6AclIndex Integer32

DiffServPolicyMapEntry  
SEQUENCE    
  diffServPolicyMapIndex Unsigned32
  diffServPolicyMapName DisplayString
  diffServPolicyMapDescription DisplayString
  diffServPolicyMapElementIndexList OCTET STRING
  diffServPolicyMapStatus RowStatus

DiffServPolicyMapElementEntry  
SEQUENCE    
  diffServPolicyMapElementIndex Unsigned32
  diffServPolicyMapElementClassMapIndex Integer32
  diffServPolicyMapElementMeterIndex Integer32
  diffServPolicyMapElementActionIndex Integer32
  diffServPolicyMapElementStatus RowStatus

DiffServClassMapEntry  
SEQUENCE    
  diffServClassMapIndex Unsigned32
  diffServClassMapName DisplayString
  diffServClassMapDescription DisplayString
  diffServClassMapMatchType INTEGER
  diffServClassMapElementIndexTypeList OCTET STRING
  diffServClassMapElementIndexList OCTET STRING
  diffServClassMapStatus RowStatus

DiffServAclEntry  
SEQUENCE    
  diffServAclIndex Unsigned32
  diffServAclName DisplayString
  diffServAclType INTEGER
  diffServAclAceIndexList OCTET STRING
  diffServAclStatus RowStatus

DiffServIpAceEntry  
SEQUENCE    
  diffServIpAceIndex Unsigned32
  diffServIpAceType INTEGER
  diffServIpAceAccess INTEGER
  diffServIpAceSourceIpAddr IpAddress
  diffServIpAceSourceIpAddrBitmask IpAddress
  diffServIpAceDestIpAddr IpAddress
  diffServIpAceDestIpAddrBitmask IpAddress
  diffServIpAceProtocol Integer32
  diffServIpAcePrec Integer32
  diffServIpAceTos Integer32
  diffServIpAceDscp Integer32
  diffServIpAceSourcePortOp INTEGER
  diffServIpAceMinSourcePort Integer32
  diffServIpAceSourcePortBitmask Integer32
  diffServIpAceDestPortOp INTEGER
  diffServIpAceMinDestPort Integer32
  diffServIpAceDestPortBitmask Integer32
  diffServIpAceControlCode Integer32
  diffServIpAceControlCodeBitmask Integer32
  diffServIpAceStatus RowStatus

DiffServMacAceEntry  
SEQUENCE    
  diffServMacAceIndex Unsigned32
  diffServMacAceAccess INTEGER
  diffServMacAcePktformat INTEGER
  diffServMacAceSourceMacAddr MacAddress
  diffServMacAceSourceMacAddrBitmask MacAddress
  diffServMacAceDestMacAddr MacAddress
  diffServMacAceDestMacAddrBitmask MacAddress
  diffServMacAceVidOp INTEGER
  diffServMacAceMinVid Integer32
  diffServMacAceVidBitmask Integer32
  diffServMacAceEtherTypeOp INTEGER
  diffServMacAceEtherTypeBitmask Integer32
  diffServMacAceMinEtherType Integer32
  diffServMacAceCosOp INTEGER
  diffServMacAceCosBitmask Integer32
  diffServMacAceMinCos Integer32
  diffServMacAceStatus RowStatus

DiffServActionEntry  
SEQUENCE    
  diffServActionIndex Unsigned32
  diffServActionList BITS
  diffServActionPktNewPri Integer32
  diffServActionPktNewDscp Integer32
  diffServActionRedPktNewDscp Integer32
  diffServActionRedDrop EnabledStatus
  diffServActionStatus RowStatus

DiffServMeterEntry  
SEQUENCE    
  diffServMeterIndex Unsigned32
  diffServMeterModel INTEGER
  diffServMeterRate Integer32
  diffServMeterBurstSize Integer32
  diffServMeterInterval Integer32
  diffServMeterStatus RowStatus

DiffServIpv6AceEntry  
SEQUENCE    
  diffServIpv6AceIndex Unsigned32
  diffServIpv6AceType INTEGER
  diffServIpv6AceAccess INTEGER
  diffServIpv6AceSourceIpAddr OCTET STRING
  diffServIpv6AceSourceIpAddrPrefixLen Integer32
  diffServIpv6AceDestIpAddr OCTET STRING
  diffServIpv6AceDestIpAddrPrefixLen Integer32
  diffServIpv6AceDscp Integer32
  diffServIpv6AceStatus RowStatus

PrivateVlanVlanEntry  
SEQUENCE    
  privateVlanVlanIndex Integer32
  privateVlanVlanType INTEGER
  privateVlanAssoicatedPrimaryVlan Integer32

PrivateVlanPrivatePortEntry  
SEQUENCE    
  privateVlanPrivatePortIfIndex Unsigned32
  privateVlanPrivatePortSecondaryVlan Integer32

PrivateVlanPromPortEntry  
SEQUENCE    
  privateVlanPromPortIfIndex Unsigned32
  privateVlanPromPortPrimaryVlanId Integer32
  privateVlanPromPortSecondaryRemap OCTET STRING
  privateVlanPromPortSecondaryRemap2k OCTET STRING
  privateVlanPromPortSecondaryRemap3k OCTET STRING
  privateVlanPromPortSecondaryRemap4k OCTET STRING

PrivateVlanSessionEntry  
SEQUENCE    
  privateVlanSessionId Unsigned32
  privateVlanSessionUplinkPorts PortList
  privateVlanSessionDownlinkPorts PortList
  privateVlanSessionStatus ValidStatus

PortSecPortEntry  
SEQUENCE    
  portSecPortIndex Unsigned32
  portSecPortStatus EnabledStatus
  portSecAction INTEGER
  portSecMaxMacCount Integer32

RadiusServerEntry  
SEQUENCE    
  radiusServerIndex Unsigned32
  radiusServerAddress IpAddress
  radiusServerAuthPortNumber Integer32
  radiusServerAcctPortNumber Integer32
  radiusServerKey DisplayString
  radiusServerRetransmit Integer32
  radiusServerTimeout Integer32
  radiusServerStatus ValidStatus

TacacsPlusServerEntry  
SEQUENCE    
  tacacsPlusServerIndex Unsigned32
  tacacsPlusServerAddress IpAddress
  tacacsPlusServerPortNumber Integer32
  tacacsPlusServerKey DisplayString
  tacacsPlusServerStatus ValidStatus
  tacacsPlusServerRetransmit Integer32
  tacacsPlusServerTimeout Integer32

SshConnInfoEntry  
SEQUENCE    
  sshConnID Unsigned32
  sshConnMajorVersion Integer32
  sshConnMinorVersion Integer32
  sshConnStatus INTEGER
  sshConnEncryptionType INTEGER
  sshConnUserName DisplayString
  sshDisconnect INTEGER
  sshConnEncryptionTypeStr DisplayString

SshUserEntry  
SEQUENCE    
  sshUserName DisplayString
  sshUserRsaKey1 KeySegment
  sshUserRsaKey2 KeySegment
  sshUserRsaKey3 KeySegment
  sshUserRsaKey4 KeySegment
  sshUserRsaKey5 KeySegment
  sshUserRsaKey6 KeySegment
  sshUserRsaKey7 KeySegment
  sshUserRsaKey8 KeySegment
  sshUserDsaKey1 KeySegment
  sshUserDsaKey2 KeySegment
  sshUserDsaKey3 KeySegment
  sshUserDsaKey4 KeySegment
  sshUserDsaKey5 KeySegment
  sshUserDsaKey6 KeySegment
  sshUserDsaKey7 KeySegment
  sshUserDsaKey8 KeySegment
  sshUserKeyDelAction INTEGER

AaaMethodEntry  
SEQUENCE    
  aaaMethodIndex Unsigned32
  aaaMethodName DisplayString
  aaaMethodGroupName DisplayString
  aaaMethodMode INTEGER
  aaaMethodStatus ValidStatus
  aaaMethodClientType INTEGER
  aaaMethodPrivilegeLevel Integer32

AaaRadiusGroupEntry  
SEQUENCE    
  aaaRadiusGroupIndex Unsigned32
  aaaRadiusGroupServerBitMap OCTET STRING
  aaaRadiusGroupName DisplayString
  aaaRadiusGroupStatus ValidStatus

AaaTacacsPlusGroupEntry  
SEQUENCE    
  aaaTacacsPlusGroupIndex Unsigned32
  aaaTacacsPlusGroupServerBitMap OCTET STRING
  aaaTacacsPlusGroupName DisplayString
  aaaTacacsPlusGroupStatus ValidStatus

AaaAccountEntry  
SEQUENCE    
  aaaAccountIfIndex Unsigned32
  aaaAccountMethodName DisplayString
  aaaAccountProtocol Integer32
  aaaAccountStatus ValidStatus

AaaCommandPrivilegesEntry  
SEQUENCE    
  aaaCommandPrivilegesLevel Integer32
  aaaCommandPrivilegesInterfaceIndex INTEGER
  aaaCommandPrivilegesMethodName DisplayString

AaaAccExecEntry  
SEQUENCE    
  aaaAccExecIndex INTEGER
  aaaAccExecMethodName DisplayString

IpFilterSnmpEntry  
SEQUENCE    
  ipFilterSnmpStartAddress IpAddress
  ipFilterSnmpEndAddress IpAddress
  ipFilterSnmpStatus ValidStatus

IpFilterHTTPEntry  
SEQUENCE    
  ipFilterHTTPStartAddress IpAddress
  ipFilterHTTPEndAddress IpAddress
  ipFilterHTTPStatus ValidStatus

IpFilterTelnetEntry  
SEQUENCE    
  ipFilterTelnetStartAddress IpAddress
  ipFilterTelnetEndAddress IpAddress
  ipFilterTelnetStatus ValidStatus

Dot1xAuthConfigExtEntry  
SEQUENCE    
  dot1xAuthConfigExtOperMode INTEGER
  dot1xAuthConfigExtMultiHostMaxCnt Integer32
  dot1xAuthConfigExtPortIntrusionAction INTEGER

NetworkAccessPortEntry  
SEQUENCE    
  networkAccessPortPortIndex Unsigned32
  networkAccessPortMaxMacCount Integer32
  networkAccessPortMacFilter Integer32
  networkAccessPortGuestVlan Integer32
  networkAccessPortLinkDetectionStatus EnabledStatus
  networkAccessPortLinkDetectionMode INTEGER
  networkAccessPortLinkDetectionAciton INTEGER
  networkAccessPortDynamicQos EnabledStatus

NetworkAccessMacAddressEntry  
SEQUENCE    
  networkAccessMacAddressAddress MacAddress
  networkAccessMacAddressPort Unsigned32
  networkAccessMacAddressInetAddressType InetAddressType
  networkAccessMacAddressRadiusServerInetAddress InetAddress
  networkAccessMacAddressTime DisplayString
  networkAccessMacAddressAttribute INTEGER

NetworkAccessMacFilterWithMaskEntry  
SEQUENCE    
  networkAccessMacFilterWithMaskID Unsigned32
  networkAccessMacFilterWithMaskMacAddress MacAddress
  networkAccessMacFilterWithMaskMacAddressMask MacAddress
  networkAccessMacFilterWithMaskStatus ValidStatus

MacAuthPortEntry  
SEQUENCE    
  macAuthPortIndex Unsigned32
  macAuthPortMaxMacCount Integer32
  macAuthPortIntrusionAction INTEGER

WebAuthPortConfigEntry  
SEQUENCE    
  webAuthPortConfigPortIndex Unsigned32
  webAuthPortConfigStatus EnabledStatus
  webAuthPortConfigAuthenticatedHostCount Integer32

WebAuthPortInfoEntry  
SEQUENCE    
  webAuthPortInfoPortIndex Unsigned32
  webAuthPortInfoPortAuthSuccessIndex Unsigned32
  webAuthPortInfoInetAddressType InetAddressType
  webAuthPortInfoInetAddress InetAddress
  webAuthPortInfoRemainingSessiontime Integer32
  webAuthPortInfoStatus INTEGER

RemoteLogServerEntry  
SEQUENCE    
  remoteLogServerIp IpAddress
  remoteLogServerStatus ValidStatus

SmtpServerIpEntry  
SEQUENCE    
  smtpServerIp IpAddress
  smtpServerIpStatus ValidStatus

SmtpDestEMailEntry  
SEQUENCE    
  smtpDestEMail DisplayString
  smtpDestEMailStatus ValidStatus

SntpServerEntry  
SEQUENCE    
  sntpServerIndex Integer32
  sntpServerIpAddress IpAddress

NtpServerEntry  
SEQUENCE    
  ntpServerIpAddress IpAddress
  ntpServerVersion Integer32
  ntpServerKeyId Integer32
  ntpServerStatus INTEGER

NtpAuthKeyEntry  
SEQUENCE    
  ntpAuthKeyId Integer32
  ntpAuthKeyWord OCTET STRING
  ntpAuthKeyStatus INTEGER

FileCopyOamResultEntry  
SEQUENCE    
  fileCopyOamLocalIfIndex InterfaceIndex
  fileCopyOamResult INTEGER

FileInfoEntry  
SEQUENCE    
  fileInfoUnitID Unsigned32
  fileInfoFileName DisplayString
  fileInfoFileType INTEGER
  fileInfoIsStartUp TruthValue
  fileInfoFileSize Integer32
  fileInfoCreationTime DisplayString
  fileInfoDelete INTEGER

FileAutoDownloadResultEntry  
SEQUENCE    
  fileAutoDownloadResultUnitID Unsigned32
  fileAutoDownloadResultAction INTEGER
  fileAutoDownloadResultStatus INTEGER

DnsHostEntry  
SEQUENCE    
  dnsHostName DisplayString
  dnsHostIndex Integer32
  dnsHostIp IpAddress

DnsDomainListEntry  
SEQUENCE    
  dnsDomainListName DisplayString
  dnsDomainListStatus ValidStatus

DnsNameServerEntry  
SEQUENCE    
  dnsNameServerIndex Integer32
  dnsNameServerIp IpAddress

DnsCacheEntry  
SEQUENCE    
  dnsCacheIndex Unsigned32
  dnsCacheFlag Integer32
  dnsCacheType INTEGER
  dnsCacheIp IpAddress
  dnsCacheTtl Integer32
  dnsCacheDomain DisplayString

McastStormEntry  
SEQUENCE    
  mcastStormIfIndex Unsigned32
  mcastStormStatus EnabledStatus
  mcastStormPktRate Integer32

BcastStormEntry  
SEQUENCE    
  bcastStormIfIndex Unsigned32
  bcastStormStatus EnabledStatus
  bcastStormPktRate Integer32

UnknownUcastStormEntry  
SEQUENCE    
  unknownUcastStormIfIndex Unsigned32
  unknownUcastStormStatus EnabledStatus
  unknownUcastStormSampleType INTEGER
  unknownUcastStormPktRate Integer32

MvrGroupEntry  
SEQUENCE    
  mvrGroupId IpAddress
  mvrGroutActive INTEGER
  mvrGroupStatus INTEGER

MvrGroupStaticEntry  
SEQUENCE    
  mvrGroupStaticAddress IpAddress
  mvrGroupStaticPorts PortList
  mvrGroupStaticStatus INTEGER

MvrGroupCurrentEntry  
SEQUENCE    
  mvrGroupCurrentAddress IpAddress
  mvrGroupCurrentPorts PortList
  mvrGroupCurrentReceiverVlan Integer32

MvrPortEntry  
SEQUENCE    
  mvrIfIndex InterfaceIndex
  mvrPortType INTEGER
  mvrPortImmediateLeave EnabledStatus
  mvrPortActive INTEGER

MvrReceiverGroupEntry  
SEQUENCE    
  mvrReceiverGroupId IpAddress
  mvrReceiverGroupActive INTEGER
  mvrReceiverGroupStatus INTEGER

MvrReceiverGroupStaticEntry  
SEQUENCE    
  mvrReceiverGroupStaticAddress IpAddress
  mvrReceiverGroupStaticPorts PortList
  mvrReceiverGroupStaticStatus INTEGER

MvrReceiverGroupCurrentEntry  
SEQUENCE    
  mvrReceiverGroupCurrentAddress IpAddress
  mvrReceiverGroupCurrentPorts PortList

DhcpSnoopVlanConfigEntry  
SEQUENCE    
  dhcpSnoopVlanIndex VlanIndex
  dhcpSnoopVlanEnable EnabledStatus

DhcpSnoopPortConfigEntry  
SEQUENCE    
  dhcpSnoopPortIfIndex InterfaceIndex
  dhcpSnoopPortTrustEnable EnabledStatus

DhcpSnoopBindingsEntry  
SEQUENCE    
  dhcpSnoopBindingsVlanIndex VlanIndex
  dhcpSnoopBindingsMacAddress MacAddress
  dhcpSnoopBindingsAddrType InetAddressType
  dhcpSnoopBindingsEntryType INTEGER
  dhcpSnoopBindingsIpAddress IpAddress
  dhcpSnoopBindingsPortIfIndex InterfaceIndex
  dhcpSnoopBindingsLeaseTime Unsigned32

ClusterCandidateEntry  
SEQUENCE    
  clusterCandidateMacAddr MacAddress
  clusterCandidateDesc DisplayString
  clusterCandidateRole INTEGER

ClusterMemberEntry  
SEQUENCE    
  clusterMemberId Unsigned32
  clusterMemberMacAddr MacAddress
  clusterMemberDesc DisplayString
  clusterMemberActive INTEGER

IpSrcGuardConfigEntry  
SEQUENCE    
  ipSrcGuardPortIfIndex InterfaceIndex
  ipSrcGuardMode INTEGER

IpSrcGuardAddrEntry  
SEQUENCE    
  ipSrcGuardBindingsVlanIndex VlanIndex
  ipSrcGuardBindingsMacAddress MacAddress
  ipSrcGuardBindingsAddrType InetAddressType
  ipSrcGuardBindingsEntryType INTEGER
  ipSrcGuardBindingsIpAddress IpAddress
  ipSrcGuardBindingsPortIfIndex InterfaceIndex
  ipSrcGuardBindingsLeaseTime Unsigned32
  ipSrcGuardBindingsStatus RowStatus

SFlowPortEntry  
SEQUENCE    
  sFlowPortIndex Unsigned32
  sFlowPortStatus EnabledStatus

OamPortStatusEntry  
SEQUENCE    
  oamPortIfIndex InterfaceIndex
  oamEnableStatus EnabledStatus

OamPortModeEntry  
SEQUENCE    
  oamPortModeIndex InterfaceIndex
  oamPortMode INTEGER

OamPortClearStatEntry  
SEQUENCE    
  oamPortClearStatIndex InterfaceIndex
  oamClearStatistics INTEGER

OamLoopbackEntry  
SEQUENCE    
  oamLoopbackTestIfIndex Unsigned32
  oamLoopbackTestPacketNumber Integer32
  oamLoopbackTestPacketSize Integer32
  oamLoopbackTestAction INTEGER
  oamLoopbackTestResultTx Counter32
  oamLoopbackTestResultRx Counter32

RemoteAcceptableFrameTypeEntry  
SEQUENCE    
  remoteAcceptableFrameTypeIndex InterfaceIndex
  remoteAcceptableFrameType INTEGER

RemoteEepromWriteEntry  
SEQUENCE    
  remoteEepromWriteIndex InterfaceIndex
  remoteEepromWriteEnableStatus EnabledStatus

RemoteFlowControlEnbaleEntry  
SEQUENCE    
  remoteFLIndex InterfaceIndex
  remoteFlowControlEnbale EnabledStatus

RemoteNegotiationEnableEntry  
SEQUENCE    
  remoteNegoIndex InterfaceIndex
  remoteNegotiationEnable EnabledStatus

RemoteShutDownEnableEntry  
SEQUENCE    
  remoteSDIndex InterfaceIndex
  remoteShutDownEnable EnabledStatus

RemoteInputToSwitchEntry  
SEQUENCE    
  remoteInputIndex InterfaceIndex
  remoteInputToSwitch INTEGER

RemoteOutputToSubscriberEntry  
SEQUENCE    
  remoteOutputIndex InterfaceIndex
  remoteOutputToSubscriber INTEGER

RemoteSpeedDuplexEntry  
SEQUENCE    
  remoteSpeedDuplexIndex InterfaceIndex
  remoteSpeedDuplex INTEGER

RemoteMdixEntry  
SEQUENCE    
  remoteMdixIndex InterfaceIndex
  remoteMdix INTEGER

RemoteDefaultEntry  
SEQUENCE    
  remoteDefaultIndex InterfaceIndex
  remoteDefaultVlan Integer32
  remoteDefaultPriority Integer32
  remoteDefaultEnable EnabledStatus

RemoteProtocolVlanEntry  
SEQUENCE    
  remoteProtocolVlanIndex InterfaceIndex
  remoteProtocolVlanEtherType Unsigned32
  remoteProtocolVlanVid Integer32
  remoteProtocolVlanPririty Integer32
  remoteProtocolVlanRowStatus RowStatus

RemoteQueueCosMapEntry  
SEQUENCE    
  remoteQueueCosMapIndex InterfaceIndex
  remoteQueueCosMapPriority Unsigned32
  remoteQueueCosMapQueue Integer32
  remoteQueueCosMapEnable EnabledStatus

RemoteQueueModeEntry  
SEQUENCE    
  remoteQueueModeIndex InterfaceIndex
  remoteQueueMode INTEGER

RemoteWrrPortEntry  
SEQUENCE    
  remoteWrrPortIfIndex Unsigned32
  remoteWrrPortQueueID Integer32
  remoteWrrPortWeight Integer32

RemoteMapTagPriStatusEntry  
SEQUENCE    
  remoteMapTagPriStatusIndex InterfaceIndex
  remoteMapTagPriStatus EnabledStatus

RemoteMapTagPriorityEntry  
SEQUENCE    
  remoteMapTagPriorityIndex Unsigned32
  remoteMapTagPriority Integer32
  remoteMapTagPriorityPri Integer32

RemoteMapTosStatusEntry  
SEQUENCE    
  remoteMapTosStatusIndex InterfaceIndex
  remoteMapTosEnableStatus EnabledStatus

RemoteMapTosEntry  
SEQUENCE    
  remoteMapTosIndex Unsigned32
  remoteMapTos Integer32
  remoteMapTosPri Integer32
  remoteMapTosStatus RowStatus

RemoteMapTrafficClassStatusEntry  
SEQUENCE    
  remoteMapTCStatusIndex InterfaceIndex
  remoteMapTCEnableStatus EnabledStatus

RemoteMapTrafficClassEntry  
SEQUENCE    
  remoteMapTrafficClassIfIndex Unsigned32
  remoteMapTrafficClass Integer32
  remoteMapCos Integer32
  remoteMapTrafficClassStatus RowStatus

RemoteFactoryDefaultEntry  
SEQUENCE    
  remoteFactoryDefaultIndex InterfaceIndex
  remoteFactoryDefault INTEGER

RemoteDeviceStatisticEntry  
SEQUENCE    
  remoteStatisticPortIndex InterfaceIndex
  remoteDeviceStatisticIfIndex Unsigned32
  remoteTxPausePacket Integer32
  remoteRxPausePacket Integer32
  remoteRxErrorPacket Integer32

RemoteQueuePacketStatisticEntry  
SEQUENCE    
  remoteQueuePacketStatisticPortIndex InterfaceIndex
  remoteQueuePacketDeviceStatisticIfIndex Unsigned32
  remoteQueuePacketQueueIndex Unsigned32
  remoteQueueDropPacket Integer32
  remoteQueueForwardingPacket Integer32

RemoteMacAddressEntry  
SEQUENCE    
  remoteMacAddressIfIndex InterfaceIndex
  remoteMacAddress OCTET STRING
  remoteMacAddressStatus ValidStatus

RemoteAccessPointEntry  
SEQUENCE    
  remoteAccessPointLocalPort InterfaceIndex
  remoteAccessPointStatus EnabledStatus

RemoteDhcpServerEntry  
SEQUENCE    
  remoteDhcpServerLocalPort InterfaceIndex
  remoteDhcpServerStatus EnabledStatus
  remoteDhcpServerIpAddress IpAddress
  remoteDhcpServerSubnetMask IpAddress
  remoteDhcpServerGateway IpAddress

RemoteVlanEntry  
SEQUENCE    
  remoteVlanLocalPort InterfaceIndex
  remoteVlanId Integer32
  remoteVlanStatus ValidStatus

RemotePortAdminEntry  
SEQUENCE    
  remotePortAdminLocalPort InterfaceIndex
  remotePortAdminRemotePort Integer32
  remotePortAdminStatus EnabledStatus

RemotePortPvidEntry  
SEQUENCE    
  remotePortPvidLocalPort InterfaceIndex
  remotePortPvidRemotePort Integer32
  remotePortPvid Integer32

RemotePortPriorityEntry  
SEQUENCE    
  remotePortPriorityLocalPort InterfaceIndex
  remotePortPriorityRemotePort Integer32
  remotePortPriority Integer32

RemotePortIgmpSnoopingEntry  
SEQUENCE    
  remotePortIgmpSnoopingLocalPort InterfaceIndex
  remotePortIgmpSnoopingRemotePort Integer32
  remotePortIgmpSnooping EnabledStatus

RemotePortCountersEntry  
SEQUENCE    
  remotePortCountersLocalPort InterfaceIndex
  remotePortCountersRemotePort Integer32
  remotePortCountersInUnicastSupported TruthValue
  remotePortCountersInUnicast Counter32
  remotePortCountersInBroadcastSupported TruthValue
  remotePortCountersInBroadcast Counter32
  remotePortCountersInPauseSupported TruthValue
  remotePortCountersInPause Counter32
  remotePortCountersInMulticastSupported TruthValue
  remotePortCountersInMulticast Counter32
  remotePortCountersOutUnicastSupported TruthValue
  remotePortCountersOutUnicast Counter32
  remotePortCountersOutBroadcastSupported TruthValue
  remotePortCountersOutBroadcast Counter32
  remotePortCountersOutMulticastSupported TruthValue
  remotePortCountersOutMulticast Counter32
  remotePortCountersInFcsErrorsSupported TruthValue
  remotePortCountersInFcsErrors Counter32
  remotePortCountersOutFcsErrorsSupported TruthValue
  remotePortCountersOutFcsErrors Counter32
  remotePortCountersInGoodOctetsSupported TruthValue
  remotePortCountersInGoodOctets Counter32
  remotePortCountersOutGoodOctetsSupported TruthValue
  remotePortCountersOutGoodOctets Counter32
  remotePortCountersInBadOctetsSupported TruthValue
  remotePortCountersInBadOctets Counter32
  remotePortCountersInDiscardsSupported TruthValue
  remotePortCountersInDiscards Counter32
  remotePortCountersAlignmentErrorsSupported TruthValue
  remotePortCountersAlignmentErrors Counter32
  remotePortCountersUndersizeErrorsSupported TruthValue
  remotePortCountersUndersizeErrors Counter32

RtrRingEntry  
SEQUENCE    
  rtrRingIndex Integer32
  rtrRingCurrentStatus INTEGER
  rtrRingName DisplayString
  rtrRingPrimaryPortIf InterfaceIndex
  rtrRingPrimaryPortStatus INTEGER
  rtrRingBackupPortIf InterfaceIndex
  rtrRingBackupPortStatus INTEGER
  rtrPrimarySeen TruthValue
  rtrSecondarySeen TruthValue
  rtrRingStatus ValidStatus

PortTestEntry  
SEQUENCE    
  testifIndex InterfaceIndex
  ifAdminSpeed INTEGER
  ifAdminPower INTEGER

Defined Values

sixnet 7.1.20540
Enterprise MIB for SIXNET products
MODULE-IDENTITY    

sixnetObjects 7.1.20540.1
OBJECT IDENTIFIER    

sixnetDevices 7.1.20540.2
OBJECT IDENTIFIER    

sixnetRTR 7.1.20540.4
OBJECT IDENTIFIER    

sixnetExperimental 7.1.20540.9999
OBJECT IDENTIFIER    

sixnetPlaypen 7.1.20540.9999.9999
OBJECT IDENTIFIER    

sixnetNotificationPrefix 7.1.20540.5
OBJECT IDENTIFIER    

sixnetNotifications 7.1.20540.5.0
OBJECT IDENTIFIER    

sixnetNotificationObjects 7.1.20540.5.1
OBJECT IDENTIFIER    

sixnetConformance 7.1.20540.6
OBJECT IDENTIFIER    

sixnetCompliances 7.1.20540.6.1
OBJECT IDENTIFIER    

sixnetGroups 7.1.20540.6.2
OBJECT IDENTIFIER    

etms 7.1.20540.2.1
OBJECT IDENTIFIER    

etmsScalars 7.1.20540.2.1.1
OBJECT IDENTIFIER    

etmsTables 7.1.20540.2.1.2
OBJECT IDENTIFIER    

etmsTest 7.1.20540.2.1.9999
OBJECT IDENTIFIER    

p1status 7.1.20540.2.1.1.1
The current operational state of P1 power input.
Status: current Access: read-only
OBJECT-TYPE    
  SixnetDiscrete  

p2status 7.1.20540.2.1.1.2
The current operational state of P2 power input.
Status: current Access: read-only
OBJECT-TYPE    
  SixnetDiscrete  

oKstatus 7.1.20540.2.1.1.3
The current operational state of OK relay output.
Status: current Access: read-only
OBJECT-TYPE    
  SixnetDiscrete  

serialNumber 7.1.20540.2.1.1.4
The serial number of the device.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sxid 7.1.20540.2.1.1.5
The SXID of the device.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

firmwareRevision 7.1.20540.2.1.1.6
The firmware revision.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

fromPLCstatus 7.1.20540.2.1.1.7
The current operational state of From PLC input.
Status: current Access: read-only
OBJECT-TYPE    
  SixnetDiscrete  

sxAllRingsGood 7.1.20540.2.1.1.8
True if all rings configured for this switch are complete.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sxAllRingNeighborsGood 7.1.20540.2.1.1.9
True if all neighbors in all configured rings for this switch are complete.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

firmwareUpdate 7.1.20540.2.1.1.10
Write a URL (ftp, tftp, http, https) to this property to begin a firmware update on the inactive location. The firmware update will proceed in the background, and may be monitored with firmwareTable.firmwareHealth. This may fail if the URL is not correct, the server is unreachable, or the download of the file from the server fails.
Status: current Access: write-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

pppTable 7.1.20540.2.1.2.1
A list of interface entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppEntry

pppEntry 7.1.20540.2.1.2.1.1
An entry containing management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  PppEntry  

pppifIndex 7.1.20540.2.1.2.1.1.1
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

pppifOperStatus 7.1.20540.2.1.2.1.1.2
The current operational state of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), down(1), up(2)  

sxRingTable 7.1.20540.2.1.2.2
A list of configured rings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SxRingEntry

sxRingEntry 7.1.20540.2.1.2.2.1
A row containing status and configuration information for a particular ring.
Status: current Access: not-accessible
OBJECT-TYPE    
  SxRingEntry  

sxRingIndex 7.1.20540.2.1.2.2.1.1
A unique value, greater than zero, identifying a ring in which this switch participates.
Status: current Access: read-only
OBJECT-TYPE    
  SxRingIndex  

sxRingName 7.1.20540.2.1.2.2.1.2
A name describing the ring, unique among configured rings. The name has no inherent meaning to the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sxRingGood 7.1.20540.2.1.2.2.1.3
True if the ring is complete, false otherwise.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sxRingPrimarySeen 7.1.20540.2.1.2.2.1.4
True if the switch has recently seen RPDUs from its primary neighbor on this ring.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sxRingBackupSeen 7.1.20540.2.1.2.2.1.5
True if the switch has recently seen RPDUs from its backup neighbor on this ring.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sxRingPrimaryIf 7.1.20540.2.1.2.2.1.6
Indicates the interface configured as the primary port for this ring. Unique among all ports for all configured rings on this switch.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

sxRingBackupIf 7.1.20540.2.1.2.2.1.7
Indicates the interface configured as the backup port for this ring. Unique among all ports for all configured rings on this switch.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

firmwareTable 7.1.20540.2.1.2.3
A list of installed firmware images.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FirmwareEntry

firmwareEntry 7.1.20540.2.1.2.3.1
An entry containing management information applicable to a particular firmware image.
Status: current Access: not-accessible
OBJECT-TYPE    
  FirmwareEntry  

firmwareIndex 7.1.20540.2.1.2.3.1.1
A value, either 1 or 2, identifying a specific firmware image location.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER first(1), second(2)  

firmwareDefault 7.1.20540.2.1.2.3.1.2
Whether the specified firmware location is the default for booting a normal switch. If the switch has failed to boot and has fallen back to the alternate image, this will remain the same. To attempt to boot the switch into the default image again, this must be set explicitly.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2), unknown(3)  

firmwareRunning 7.1.20540.2.1.2.3.1.3
Whether the specified firmware location provided the firmware which is currently running in the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2), unknown(3)  

firmwareVersion 7.1.20540.2.1.2.3.1.4
The firmware revision of the firmware in this location, or '(Unknown)' if it cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

firmwareHealth 7.1.20540.2.1.2.3.1.5
The status of this firmware location. Healthy(1) means that the image is either running currently, or should be able to run. Broken(2) means the image is known to not be bootable, and cannot be set as the default image. Loading(3) means that a firmware load is currently taking place on that image. Unknown(4) means that the image was expected to boot, but did not, so the bootability of that image cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER healthy(1), broken(2), loading(3), unknown(4)  

sixnetCompliance1 7.1.20540.6.1.1
This really just keeps MIB verification programs happy because there is no external standard to which our private MIB must conform.
Status: current Access: read-only
MODULE-COMPLIANCE    

sixnetSwitchGroup 7.1.20540.6.2.1
A collection of objects providing information about SIXNET switches
Status: current Access: read-only
OBJECT-GROUP    

sixnetTestGroup 7.1.20540.6.2.2
A collection of objects for testing.
Status: current Access: read-only
OBJECT-GROUP    

stakable 7.1.20540.2.2
OBJECT IDENTIFIER    

el228MIB 7.1.20540.2.2.1
OBJECT IDENTIFIER    

el228MIBObjects 7.1.20540.2.2.1.1
OBJECT IDENTIFIER    

el228Notifications 7.1.20540.2.2.1.2
OBJECT IDENTIFIER    

el228Conformance 7.1.20540.2.2.1.3
OBJECT IDENTIFIER    

switchMgt 7.1.20540.2.2.1.1.1
OBJECT IDENTIFIER    

portMgt 7.1.20540.2.2.1.1.2
OBJECT IDENTIFIER    

trunkMgt 7.1.20540.2.2.1.1.3
OBJECT IDENTIFIER    

lacpMgt 7.1.20540.2.2.1.1.4
OBJECT IDENTIFIER    

staMgt 7.1.20540.2.2.1.1.5
OBJECT IDENTIFIER    

restartMgt 7.1.20540.2.2.1.1.7
OBJECT IDENTIFIER    

mirrorMgt 7.1.20540.2.2.1.1.8
OBJECT IDENTIFIER    

igmpSnoopMgt 7.1.20540.2.2.1.1.9
OBJECT IDENTIFIER    

ipMgt 7.1.20540.2.2.1.1.10
OBJECT IDENTIFIER    

vlanMgt 7.1.20540.2.2.1.1.12
OBJECT IDENTIFIER    

priorityMgt 7.1.20540.2.2.1.1.13
OBJECT IDENTIFIER    

trapDestMgt 7.1.20540.2.2.1.1.14
OBJECT IDENTIFIER    

qosMgt 7.1.20540.2.2.1.1.16
OBJECT IDENTIFIER    

securityMgt 7.1.20540.2.2.1.1.17
OBJECT IDENTIFIER    

sysLogMgt 7.1.20540.2.2.1.1.19
OBJECT IDENTIFIER    

lineMgt 7.1.20540.2.2.1.1.20
OBJECT IDENTIFIER    

sysTimeMgt 7.1.20540.2.2.1.1.23
OBJECT IDENTIFIER    

fileMgt 7.1.20540.2.2.1.1.24
OBJECT IDENTIFIER    

dnsMgt 7.1.20540.2.2.1.1.26
OBJECT IDENTIFIER    

stormMgt 7.1.20540.2.2.1.1.33
OBJECT IDENTIFIER    

mvrMgt 7.1.20540.2.2.1.1.44
OBJECT IDENTIFIER    

dhcpSnoopMgt 7.1.20540.2.2.1.1.46
OBJECT IDENTIFIER    

clusterMgt 7.1.20540.2.2.1.1.47
OBJECT IDENTIFIER    

ipSrcGuardMgt 7.1.20540.2.2.1.1.48
OBJECT IDENTIFIER    

upnpMgt 7.1.20540.2.2.1.1.49
OBJECT IDENTIFIER    

oamMgt 7.1.20540.2.2.1.1.52
OBJECT IDENTIFIER    

remoteMgt 7.1.20540.2.2.1.1.53
OBJECT IDENTIFIER    

sFlowMgt 7.1.20540.2.2.1.1.55
OBJECT IDENTIFIER    

switchManagementVlan 7.1.20540.2.2.1.1.1.1
The VLAN on which management is done.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

switchNumber 7.1.20540.2.2.1.1.1.2
The total number of switches present on this system.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

switchInfoTable 7.1.20540.2.2.1.1.1.3
Table of descriptive and status information about the switch units in this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchInfoEntry

switchInfoEntry 7.1.20540.2.2.1.1.1.3.1
Table providing descriptions and status information for switch units.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwitchInfoEntry  

swUnitIndex 7.1.20540.2.2.1.1.1.3.1.1
This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

swHardwareVer 7.1.20540.2.2.1.1.1.3.1.2
Hardware version of the main board.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swMicrocodeVer 7.1.20540.2.2.1.1.1.3.1.3
Microcode version of the main board.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swLoaderVer 7.1.20540.2.2.1.1.1.3.1.4
Loader version of the main board.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swBootRomVer 7.1.20540.2.2.1.1.1.3.1.5
Boot ROM code version of the main board.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swOpCodeVer 7.1.20540.2.2.1.1.1.3.1.6
Operation code version of the main board.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

swPortNumber 7.1.20540.2.2.1.1.1.3.1.7
The number of ports on this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swPowerStatus 7.1.20540.2.2.1.1.1.3.1.8
Indicates the switch using internalPower(1), redundantPower(2) or both(3)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER internalPower(1), redundantPower(2), internalAndRedundantPower(3)  

swRoleInSystem 7.1.20540.2.2.1.1.1.3.1.9
Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER master(1), backupMaster(2), slave(3)  

swSerialNumber 7.1.20540.2.2.1.1.1.3.1.10
Serial number of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

swServiceTag 7.1.20540.2.2.1.1.1.3.1.13
Service tag serial-number of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

swModelNumber 7.1.20540.2.2.1.1.1.3.1.14
Model number of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

swEpldVer 7.1.20540.2.2.1.1.1.3.1.15
The EPLD version of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

switchOperState 7.1.20540.2.2.1.1.1.4
Global operation state of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), unknown(2), ok(3), noncritical(4), critical(5), nonrecoverable(6)  

switchProductId 7.1.20540.2.2.1.1.1.5
OBJECT IDENTIFIER    

swProdName 7.1.20540.2.2.1.1.1.5.1
The product name of this switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdManufacturer 7.1.20540.2.2.1.1.1.5.2
The product manufacturer of this switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdDescription 7.1.20540.2.2.1.1.1.5.3
The product description of this switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdVersion 7.1.20540.2.2.1.1.1.5.4
The runtime code version of this switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

swProdUrl 7.1.20540.2.2.1.1.1.5.5
The URL of this switch, which we can connect through a web browser.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

swIdentifier 7.1.20540.2.2.1.1.1.5.6
A unique identifier of which switch in the chassis is currently being looked at.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swChassisServiceTag 7.1.20540.2.2.1.1.1.5.7
The service tag of the chassis this switch resides in.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..80)  

switchIndivPowerTable 7.1.20540.2.2.1.1.1.6
Table about the status of individual powers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchIndivPowerEntry

switchIndivPowerEntry 7.1.20540.2.2.1.1.1.6.1
Table about the status of individual power.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwitchIndivPowerEntry  

swIndivPowerUnitIndex 7.1.20540.2.2.1.1.1.6.1.1
This is defined as swUnitIndex.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

swIndivPowerIndex 7.1.20540.2.2.1.1.1.6.1.2
1 means internal power, 2 means external power.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER internalPower(1), externalPower(2)  

swIndivPowerStatus 7.1.20540.2.2.1.1.1.6.1.3
notPresent(1) means not present, green(2) means up, red(3) means down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notPresent(1), green(2), red(3)  

switchJumboFrameStatus 7.1.20540.2.2.1.1.1.7
enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

amtrMgt 7.1.20540.2.2.1.1.1.8
OBJECT IDENTIFIER    

amtrMacAddrAgingStatus 7.1.20540.2.2.1.1.1.8.3
If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

portTable 7.1.20540.2.2.1.1.2.1
Table of descriptive and status information describing the configuration of each switch port. This table also contains information about each trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 7.1.20540.2.2.1.1.2.1.1
An entry in the table, describing the configuration of one switch port or trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portIndex 7.1.20540.2.2.1.1.2.1.1.1
The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

portName 7.1.20540.2.2.1.1.2.1.1.2
The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

portType 7.1.20540.2.2.1.1.2.1.1.3
Indicates the port type of the configuration of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), hundredBaseTX(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), thousandBaseT(6), thousandBaseGBIC(7), thousandBaseSfp(8), hundredBaseFxScSingleMode(9), hundredBaseFxScMultiMode(10), thousandBaseCX(11), tenG(12)  

portSpeedDpxCfg 7.1.20540.2.2.1.1.2.1.1.4
Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode halfDuplex10g(8) - 10g and half duplex mode fullDuplex10g(9) - 10g and full duplex mode hundredBaseTX port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as: fullDuplex100(5) thousandBaseSX port can be set as: fullDuplex1000(7) thousandBaseLX port can be set as: fullDuplex1000(7) thousandBaseT port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) thousandBaseGBIC port can be set as: fullDuplex1000(7) thousandBaseSfp port can be set as: fullDuplex1000(7) hundredBaseFxScSingleMode port can be set as: fullDuplex100(5) hundredBaseFxScMultiMode port can be set as: fullDuplex100(5) thousandBaseCX port can be set as: fullDuplex1000(7) tenG port can be set as: halfDuplex10g(8) fullDuplex10g(9) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reserved(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9)  

portFlowCtrlCfg 7.1.20540.2.2.1.1.2.1.1.5
(1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (5) Flow control mechanism is enabled with tx pause mechanism only. (6) Flow control mechansim is enabled with rx pause mechansim only. Fast ethernet ports can be set as: enabled(1), disabled(2). Gigabit ethernet ports can be set as: enabled(1), disabled(2), tx(5), rx(6). The actual flow control mechanism is used given by portFlowCtrlStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), tx(5), rx(6)  

portCapabilities 7.1.20540.2.2.1.1.2.1.1.6
Port or trunk capabilities.
Status: current Access: read-write
OBJECT-TYPE    
  BITS portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), portCap10gHalf(6), portCap10gFull(7), reserved8(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), portCapSym(14), portCapFlowCtrl(15)  

portAutonegotiation 7.1.20540.2.2.1.1.2.1.1.7
Whether auto-negotiation is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

portSpeedDpxStatus 7.1.20540.2.2.1.1.2.1.1.8
The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case the value is error(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER error(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9)  

portFlowCtrlStatus 7.1.20540.2.2.1.1.2.1.1.9
(2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently configured then this value is error(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER error(1), backPressure(2), dot3xFlowControl(3), none(4)  

portTrunkIndex 7.1.20540.2.2.1.1.2.1.1.10
The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding trunkPorts.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portComboForcedMode 7.1.20540.2.2.1.1.2.1.1.12
This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal to none(1), and setting this variable to none(1) is not allowed. copperForced(2) is set if user want to force this combo port running in copper mode. copperPreferredAuto(3) is obsoleted, and user shall not set this state. sfpForced(4) is set if user want to force this combo port running in fiber mode. sfpPreferredAuto(5) is set if user want to change copper or fiber mode automatically by SFP transceiver present state. If SFP transceiver is present, this combo port will run in fiber mode, and if SFP transceiver is not present, this combo port will run in copper mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), copperForced(2), copperPreferredAuto(3), sfpForced(4), sfpPreferredAuto(5)  

portMasterSlaveModeCfg 7.1.20540.2.2.1.1.2.1.1.15
Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER master(1), slave(2), auto(3), autoPreferMaster(4), autoPreferSlave(5)  

trunkMaxId 7.1.20540.2.2.1.1.3.1
The maximum number for a trunk identifier.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

trunkValidNumber 7.1.20540.2.2.1.1.3.2
The number of valid trunks.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

trunkTable 7.1.20540.2.2.1.1.3.3
Table describing the configuration and status of each trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrunkEntry

trunkEntry 7.1.20540.2.2.1.1.3.3.1
An entry describing the configuration and status of a particular trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  TrunkEntry  

trunkIndex 7.1.20540.2.2.1.1.3.3.1.1
Identifies the trunk within the switch that is described by the table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

trunkPorts 7.1.20540.2.2.1.1.3.3.1.2
The complete set of ports currently associated with this trunk.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

trunkCreation 7.1.20540.2.2.1.1.3.3.1.3
A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

trunkStatus 7.1.20540.2.2.1.1.3.3.1.4
Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

lacpPortTable 7.1.20540.2.2.1.1.4.1
Table for LACP port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LacpPortEntry

lacpPortEntry 7.1.20540.2.2.1.1.4.1.1
Entry for LACP port configuration. While an entry may exist for a particular port, the port may not support LACP and an attempt to enable LACP may result in failure.
Status: current Access: not-accessible
OBJECT-TYPE    
  LacpPortEntry  

lacpPortIndex 7.1.20540.2.2.1.1.4.1.1.1
The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

lacpPortStatus 7.1.20540.2.2.1.1.4.1.1.2
Whether 802.3ad LACP is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staSystemStatus 7.1.20540.2.2.1.1.5.1
Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staPortTable 7.1.20540.2.2.1.1.5.2
The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StaPortEntry

staPortEntry 7.1.20540.2.2.1.1.5.2.1
The conceptual entry of staPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  StaPortEntry  

staPortFastForward 7.1.20540.2.2.1.1.5.2.1.2
Whether fast forwarding is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staPortProtocolMigration 7.1.20540.2.2.1.1.5.2.1.3
When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

staPortOperEdgePort 7.1.20540.2.2.1.1.5.2.1.5
The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

staPortAdminPointToPoint 7.1.20540.2.2.1.1.5.2.1.6
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

staPortOperPointToPoint 7.1.20540.2.2.1.1.5.2.1.7
The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the staPortAdminPointToPoint object.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

staPortSystemStatus 7.1.20540.2.2.1.1.5.2.1.9
Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staPortLongAdminPathCost 7.1.20540.2.2.1.1.5.2.1.10
The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated. Setting this to 0 means that the path cost is automatically determined. In this case, read staPortLongOperPathCost to get the oper value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..200000000  

staPortLongOperPathCost 7.1.20540.2.2.1.1.5.2.1.11
The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..200000000  

staPortRootGuardAdminStatus 7.1.20540.2.2.1.1.5.2.1.13
Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staPortRootGuardOperStatus 7.1.20540.2.2.1.1.5.2.1.14
The current operational status of the root guard which provides a way to enforce the root bridge placement in the network.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

staPortBpduGuard 7.1.20540.2.2.1.1.5.2.1.15
A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staPortAdminEdgePortWithAuto 7.1.20540.2.2.1.1.5.2.1.17
The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port and a value of auot (3) indicates this port in RSPT or MSTP mode should be assumed as an edge-port after migration or max age expire without receiving any BPDU and sending BPDU with proposal flag on.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), auto(3)  

staPortBpduFilter 7.1.20540.2.2.1.1.5.2.1.18
The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid transmitting BPDUs on edge-port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staProtocolType 7.1.20540.2.2.1.1.5.3
The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates that the Rapid Spanning Tree Protocol is as specified in IEEE 802.1w, and the value 'mstp(3)' indicates that the Multiple Spanning Tree Protocol is as specified in IEEE 802.1s. New values may be defined in the future as new or updated versions of the protocol become available.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stp(1), rstp(2), mstp(3)  

staTxHoldCount 7.1.20540.2.2.1.1.5.4
The value used by the Port Transmit state machine to limit the maximum transmission rate.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

staPathCostMethod 7.1.20540.2.2.1.1.5.5
Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the staPortLongPathCost MIB object must be used to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of staPortLongPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.
Status: current Access: read-write
OBJECT-TYPE    
  StaPathCostMode  

xstMgt 7.1.20540.2.2.1.1.5.6
OBJECT IDENTIFIER    

mstName 7.1.20540.2.2.1.1.5.6.1
The name of the Multiple Spanning Tree region.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

mstRevision 7.1.20540.2.2.1.1.5.6.2
The Revision number of the Multiple Spanning Tree region.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mstMaxHops 7.1.20540.2.2.1.1.5.6.3
The max hop number counts of the Multiple Spanning Tree region.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..40  

xstInstanceCfgTable 7.1.20540.2.2.1.1.5.6.4
This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use, the mstInstanceEditIndex is always 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XstInstanceCfgEntry

xstInstanceCfgEntry 7.1.20540.2.2.1.1.5.6.4.1
A conceptual row containing the property of the RST or MST instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  XstInstanceCfgEntry  

xstInstanceCfgIndex 7.1.20540.2.2.1.1.5.6.4.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..4094  

xstInstanceCfgPriority 7.1.20540.2.2.1.1.5.6.4.1.2
The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..61440  

xstInstanceCfgTimeSinceTopologyChange 7.1.20540.2.2.1.1.5.6.4.1.3
The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

xstInstanceCfgTopChanges 7.1.20540.2.2.1.1.5.6.4.1.4
The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xstInstanceCfgDesignatedRoot 7.1.20540.2.2.1.1.5.6.4.1.5
The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identifier parameter in all configuration bridge PDUs originated by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

xstInstanceCfgRootCost 7.1.20540.2.2.1.1.5.6.4.1.6
The cost of the path to the root as seen from this bridge of the RST or MST.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xstInstanceCfgRootPort 7.1.20540.2.2.1.1.5.6.4.1.7
The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xstInstanceCfgMaxAge 7.1.20540.2.2.1.1.5.6.4.1.8
The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgHelloTime 7.1.20540.2.2.1.1.5.6.4.1.9
The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using in RST or MST.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgHoldTime 7.1.20540.2.2.1.1.5.6.4.1.10
This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgForwardDelay 7.1.20540.2.2.1.1.5.6.4.1.11
For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the port stays in each of the listening and learning states, which precede the forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the forwarding database. This value is the current value being used by the bridge. xstInstanceCfgBridgeForwardDelay defines the value that this bridge and all others would start using if/when this bridge were to become the root.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeMaxAge 7.1.20540.2.2.1.1.5.6.4.1.12
For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeHelloTime 7.1.20540.2.2.1.1.5.6.4.1.13
For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgBridgeForwardDelay 7.1.20540.2.2.1.1.5.6.4.1.14
For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

xstInstanceCfgTxHoldCount 7.1.20540.2.2.1.1.5.6.4.1.15
For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xstInstanceCfgPathCostMethod 7.1.20540.2.2.1.1.5.6.4.1.16
For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the xstInstancePortPathCost MIB object must be used in order to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of xstInstancePortPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.
Status: current Access: read-only
OBJECT-TYPE    
  StaPathCostMode  

xstInstancePortTable 7.1.20540.2.2.1.1.5.6.5
The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XstInstancePortEntry

xstInstancePortEntry 7.1.20540.2.2.1.1.5.6.5.1
The conceptual row for xstInstancePortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XstInstancePortEntry  

xstInstancePortInstance 7.1.20540.2.2.1.1.5.6.5.1.1
The instance of the MSTP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

xstInstancePortPort 7.1.20540.2.2.1.1.5.6.5.1.2
The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1dStpPort in the BRIDGE-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

xstInstancePortPriority 7.1.20540.2.2.1.1.5.6.5.1.3
Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..240  

xstInstancePortState 7.1.20540.2.2.1.1.5.6.5.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, but does not forward packets. learning(2): Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses. forwarding(3): Port forwards packets, and continues learning addresses. For ports which are disabled (see xstInstancePortEnable), this object will have a value of discarding(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3)  

xstInstancePortEnable 7.1.20540.2.2.1.1.5.6.5.1.5
The enabled/disabled status of the port.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

xstInstancePortPathCost 7.1.20540.2.2.1.1.5.6.5.1.6
The pathcost of the RST or MST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200000000  

xstInstancePortDesignatedRoot 7.1.20540.2.2.1.1.5.6.5.1.7
The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

xstInstancePortDesignatedCost 7.1.20540.2.2.1.1.5.6.5.1.8
The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

xstInstancePortDesignatedBridge 7.1.20540.2.2.1.1.5.6.5.1.9
The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

xstInstancePortDesignatedPort 7.1.20540.2.2.1.1.5.6.5.1.10
The port identifier of the port on the designated bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

xstInstancePortForwardTransitions 7.1.20540.2.2.1.1.5.6.5.1.11
The number of times this port has transitioned from the learning state to the forwarding state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xstInstancePortPortRole 7.1.20540.2.2.1.1.5.6.5.1.12
The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port is connecting a LAN through the bridge to the root bridge (i.e., designated port) (4) The port may provide connectivity if other bridges, bridge ports, or LANs fail or are removed. (5) The port provides backup if other bridges, bridge ports, or LANs fail or are removed. (6) For MST protocol only, indicates whether this instance is in a master role.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), root(2), designated(3), alternate(4), backup(5), master(6)  

xstInstancePortAdminPathCost 7.1.20540.2.2.1.1.5.6.5.1.13
The admin value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200000000  

xstInstancePortOperPathCost 7.1.20540.2.2.1.1.5.6.5.1.14
The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..200000000  

mstInstanceEditTable 7.1.20540.2.2.1.1.5.6.6
The Multiple Spanning Tree region instance vlan configuration table. Please read the actual instance vlan mapped in the mstInstanceOperTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstInstanceEditEntry

mstInstanceEditEntry 7.1.20540.2.2.1.1.5.6.6.1
A conceptual row containing the status of the MSTP instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstInstanceEditEntry  

mstInstanceEditIndex 7.1.20540.2.2.1.1.5.6.6.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..4094  

mstInstanceEditVlansMap 7.1.20540.2.2.1.1.5.6.6.1.2
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap2k 7.1.20540.2.2.1.1.5.6.6.1.3
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap3k 7.1.20540.2.2.1.1.5.6.6.1.4
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditVlansMap4k 7.1.20540.2.2.1.1.5.6.6.1.5
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceEditRemainingHops 7.1.20540.2.2.1.1.5.6.6.1.6
The remaining hop count for this MST instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mstInstanceOperTable 7.1.20540.2.2.1.1.5.6.7
The Multiple Spanning Tree region instance vlan mapped table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstInstanceOperEntry

mstInstanceOperEntry 7.1.20540.2.2.1.1.5.6.7.1
A conceptual row containing the status of the MSTP instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstInstanceOperEntry  

mstInstanceOperIndex 7.1.20540.2.2.1.1.5.6.7.1.1
An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..4094  

mstInstanceOperVlansMap 7.1.20540.2.2.1.1.5.6.7.1.2
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap2k 7.1.20540.2.2.1.1.5.6.7.1.3
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap3k 7.1.20540.2.2.1.1.5.6.7.1.4
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstInstanceOperVlansMap4k 7.1.20540.2.2.1.1.5.6.7.1.5
A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

staLoopbackDetectionPortTable 7.1.20540.2.2.1.1.5.7
A table provides the mechanism to configure the spanning tree loopback detection of each port or trunk
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StaLoopbackDetectionPortEntry

staLoopbackDetectionPortEntry 7.1.20540.2.2.1.1.5.7.1
A conceptual row of staLoopbackDetectionPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  StaLoopbackDetectionPortEntry  

staLoopbackDetectionPortIfIndex 7.1.20540.2.2.1.1.5.7.1.1
The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

staLoopbackDetectionPortStatus 7.1.20540.2.2.1.1.5.7.1.2
Status of the port on whether spanning tree loopback detection is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staLoopbackDetectionPortTrapStatus 7.1.20540.2.2.1.1.5.7.1.3
The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

staLoopbackDetectionPortReleaseMode 7.1.20540.2.2.1.1.5.7.1.4
Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manually after loopback has occurred.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

staLoopbackDetectionPortRelease 7.1.20540.2.2.1.1.5.7.1.5
Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noRelease(1), release(2)  

restartOpCodeFile 7.1.20540.2.2.1.1.7.1
Name of op-code file for start-up.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

restartConfigFile 7.1.20540.2.2.1.1.7.2
Name of configuration file for start-up.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

restartControl 7.1.20540.2.2.1.1.7.3
Setting this object to warmBoot(2) causes the device to reinitialize itself such that neither the agent configuration nor the protocol entity implementation is altered. Setting this object to coldBoot(3) causes the device to reinitialize itself such that the agent's configuration or the protocol entity implementation may be altered. When the device is running normally, this variable has a value of running(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER running(1), warmBoot(2), coldBoot(3)  

mirrorTable 7.1.20540.2.2.1.1.8.1
Table for port mirroring, enabling a port to be mirrored to/from another port. Not all ports can be mirrored and limitations may apply as to which ports can be used as either source or destination ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MirrorEntry

mirrorEntry 7.1.20540.2.2.1.1.8.1.1
The conceptual row of mirrorTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MirrorEntry  

mirrorDestinationPort 7.1.20540.2.2.1.1.8.1.1.1
The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

mirrorSourcePort 7.1.20540.2.2.1.1.8.1.1.2
The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

mirrorType 7.1.20540.2.2.1.1.8.1.1.3
If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rx(1), tx(2), both(3)  

mirrorStatus 7.1.20540.2.2.1.1.8.1.1.4
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

vlanMirrorTable 7.1.20540.2.2.1.1.8.2
Table for VLAN mirroring, enabling a VLAN to be mirrored to a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanMirrorEntry

vlanMirrorEntry 7.1.20540.2.2.1.1.8.2.1
The conceptual row of vlanMirrorTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanMirrorEntry  

vlanMirrorDestinationPort 7.1.20540.2.2.1.1.8.2.1.1
The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vlanMirrorSourceVlan 7.1.20540.2.2.1.1.8.2.1.2
The source VLAN for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vlanMirrorStatus 7.1.20540.2.2.1.1.8.2.1.4
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

igmpSnoopStatus 7.1.20540.2.2.1.1.9.1
Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopQuerier 7.1.20540.2.2.1.1.9.2
Enables (disables) whether the switch acts as an IGMP querier.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopQueryCount 7.1.20540.2.2.1.1.9.3
The query count from a querier, during which a response is expected from an endstation. If a querier has sent a number of counts defined by igmpSnoopQueryCount, but an endstation has not responded, a countdown timer is started using the time defined by igmpSnoopQueryMaxResponseTime. If the countdown finishes, and the endstation still has not responded, then that endstation is deemed to have left the multicast group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..10  

igmpSnoopQueryInterval 7.1.20540.2.2.1.1.9.4
The interval (in seconds) between IGMP host-query messages sent by the switch.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..125  

igmpSnoopQueryMaxResponseTime 7.1.20540.2.2.1.1.9.5
The time after a query, during which a response is expected from an endstation. If a querier has sent a number of queries defined by igmpSnoopQueryCount, but an endstation has not responded, a countdown timer is started using an initial value set by igmpSnoopQueryMaxResponseTime. If the countdown finishes, and the endstation still has not responded, then that the endstation is deemed to have left the multicast group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..25  

igmpSnoopRouterPortExpireTime 7.1.20540.2.2.1.1.9.6
Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous querier) expires.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..500  

igmpSnoopVersion 7.1.20540.2.2.1.1.9.7
IGMP version snooped
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

igmpSnoopRouterCurrentTable 7.1.20540.2.2.1.1.9.8
Table for current router ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopRouterCurrentEntry

igmpSnoopRouterCurrentEntry 7.1.20540.2.2.1.1.9.8.1
Entry for current router ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopRouterCurrentEntry  

igmpSnoopRouterCurrentVlanIndex 7.1.20540.2.2.1.1.9.8.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopRouterCurrentPorts 7.1.20540.2.2.1.1.9.8.1.2
The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpSnoopRouterCurrentStatus 7.1.20540.2.2.1.1.9.8.1.3
The set of ports which are static router ports.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpSnoopRouterStaticTable 7.1.20540.2.2.1.1.9.9
Table for static router ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopRouterStaticEntry

igmpSnoopRouterStaticEntry 7.1.20540.2.2.1.1.9.9.1
Entry for static router ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopRouterStaticEntry  

igmpSnoopRouterStaticVlanIndex 7.1.20540.2.2.1.1.9.9.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopRouterStaticPorts 7.1.20540.2.2.1.1.9.9.1.2
The set of ports which are static router ports.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

igmpSnoopRouterStaticStatus 7.1.20540.2.2.1.1.9.9.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

igmpSnoopMulticastCurrentTable 7.1.20540.2.2.1.1.9.10
Table for current multicast addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopMulticastCurrentEntry

igmpSnoopMulticastCurrentEntry 7.1.20540.2.2.1.1.9.10.1
Entry for current multicast addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopMulticastCurrentEntry  

igmpSnoopMulticastCurrentVlanIndex 7.1.20540.2.2.1.1.9.10.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopMulticastCurrentIpAddress 7.1.20540.2.2.1.1.9.10.1.2
IP address of multicast group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

igmpSnoopMulticastCurrentPorts 7.1.20540.2.2.1.1.9.10.1.3
The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastCurrentStatus 7.1.20540.2.2.1.1.9.10.1.4
The set of ports which are static members.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastStaticTable 7.1.20540.2.2.1.1.9.11
Table for static multicast addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopMulticastStaticEntry

igmpSnoopMulticastStaticEntry 7.1.20540.2.2.1.1.9.11.1
Entry for static multicast addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopMulticastStaticEntry  

igmpSnoopMulticastStaticVlanIndex 7.1.20540.2.2.1.1.9.11.1.1
The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopMulticastStaticIpAddress 7.1.20540.2.2.1.1.9.11.1.2
IP address of multicast group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

igmpSnoopMulticastStaticPorts 7.1.20540.2.2.1.1.9.11.1.3
The set of ports which are members.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

igmpSnoopMulticastStaticStatus 7.1.20540.2.2.1.1.9.11.1.4
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

igmpSnoopCurrentVlanTable 7.1.20540.2.2.1.1.9.14
Table for enabling or disabling IGMP snooping per VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopCurrentVlanEntry

igmpSnoopCurrentVlanEntry 7.1.20540.2.2.1.1.9.14.1
Entry for enabling or disabling IGMP snooping.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopCurrentVlanEntry  

igmpSnoopCurrentVlanIndex 7.1.20540.2.2.1.1.9.14.1.1
Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopCurrentVlanImmediateLeave 7.1.20540.2.2.1.1.9.14.1.3
The parameter to enable or disable the Immediate-Leave feature on this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopLeaveProxy 7.1.20540.2.2.1.1.9.15
This enables or disables Leave Proxy for IGMP Snooping.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopFilterStatus 7.1.20540.2.2.1.1.9.17
Parameter to enable or disable IGMP filtering on the device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

igmpSnoopProfileTable 7.1.20540.2.2.1.1.9.18
The table for configuring the IGMP snooping profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopProfileEntry

igmpSnoopProfileEntry 7.1.20540.2.2.1.1.9.18.1
The entry for configuring the IGMP snooping profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopProfileEntry  

igmpSnoopProfileId 7.1.20540.2.2.1.1.9.18.1.1
The ID of the IGMP snooping profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileAction 7.1.20540.2.2.1.1.9.18.1.2
The access mode of the IGMP snooping profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

igmpSnoopProfileStatus 7.1.20540.2.2.1.1.9.18.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-write
OBJECT-TYPE    
  ValidStatus  

igmpSnoopProfileCtl 7.1.20540.2.2.1.1.9.19
OBJECT IDENTIFIER    

igmpSnoopProfileCtlId 7.1.20540.2.2.1.1.9.19.1
The ID of the IGMP snooping profile.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileCtlInetAddressType 7.1.20540.2.2.1.1.9.19.2
The address type is associated with this agent. Only ipv4(1) type is supported.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

igmpSnoopProfileCtlStartInetAddress 7.1.20540.2.2.1.1.9.19.3
The specified addresses in the start of the controlled IP multicast addresses.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileCtlEndInetAddress 7.1.20540.2.2.1.1.9.19.4
The specified addresses in the end of the controlled IP multicast addresses.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileCtlAction 7.1.20540.2.2.1.1.9.19.5
Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast addresses. When the action is completed, this object becomes noAction(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), create(2), destroy(3)  

igmpSnoopProfileRangeTable 7.1.20540.2.2.1.1.9.20
The table for configuring the range of the IGMP snooping profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopProfileRangeEntry

igmpSnoopProfileRangeEntry 7.1.20540.2.2.1.1.9.20.1
The entry for configuring the range of the IGMP snooping profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopProfileRangeEntry  

igmpSnoopProfileRangeProfileId 7.1.20540.2.2.1.1.9.20.1.1
This is defined as igmpSnoopProfileId.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopProfileRangeInetAddressType 7.1.20540.2.2.1.1.9.20.1.2
The address type is associated with this agent. Only ipv4(1) type is supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

igmpSnoopProfileRangeStartInetAddress 7.1.20540.2.2.1.1.9.20.1.3
The specified addresses in the start of the controlled IP multicast addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileRangeEndInetAddress 7.1.20540.2.2.1.1.9.20.1.4
The specified addresses in the end of the controlled IP multicast addresses.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

igmpSnoopProfileRangeAction 7.1.20540.2.2.1.1.9.20.1.5
The access mode of the IGMP snooping profile.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

igmpSnoopFilterPortTable 7.1.20540.2.2.1.1.9.21
Table for port configuration in IGMP filtering.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopFilterPortEntry

igmpSnoopFilterPortEntry 7.1.20540.2.2.1.1.9.21.1
Entry for port configuration in IGMP filtering.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopFilterPortEntry  

igmpSnoopFilterPortIndex 7.1.20540.2.2.1.1.9.21.1.1
The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopFilterPortProfileId 7.1.20540.2.2.1.1.9.21.1.2
The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTable, then no association exists. In particular, if this value is zero, no associated profile will be generated, as zero is not a valid profile index.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

igmpSnoopThrottlePortTable 7.1.20540.2.2.1.1.9.22
Table for port configuration in IGMP throttling.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopThrottlePortEntry

igmpSnoopThrottlePortEntry 7.1.20540.2.2.1.1.9.22.1
Entry for port configuration in IGMP throttling.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpSnoopThrottlePortEntry  

igmpSnoopThrottlePortIndex 7.1.20540.2.2.1.1.9.22.1.1
The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

igmpSnoopThrottlePortRunningStatus 7.1.20540.2.2.1.1.9.22.1.2
Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

igmpSnoopThrottlePortAction 7.1.20540.2.2.1.1.9.22.1.3
The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join. A value of deny(2) means to deny the IGMP report request when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER replace(1), deny(2)  

igmpSnoopThrottlePortMaxGroups 7.1.20540.2.2.1.1.9.22.1.4
The maximum number of IGMP groups that the interface can join.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..256  

igmpSnoopThrottlePortCurrentGroups 7.1.20540.2.2.1.1.9.22.1.5
The current number of IGMP groups that the interface has joined.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

netConfigTable 7.1.20540.2.2.1.1.10.1
A table of netConfigEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetConfigEntry

netConfigEntry 7.1.20540.2.2.1.1.10.1.1
A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetConfigEntry  

netConfigIfIndex 7.1.20540.2.2.1.1.10.1.1.1
The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

netConfigIPAddress 7.1.20540.2.2.1.1.10.1.1.2
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

netConfigSubnetMask 7.1.20540.2.2.1.1.10.1.1.3
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

netConfigPrimaryInterface 7.1.20540.2.2.1.1.10.1.1.4
Whether this is a primary interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

netConfigUnnumbered 7.1.20540.2.2.1.1.10.1.1.5
Whether this is an unnumbered interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unnumbered(1), notUnnumbered(2)  

netConfigStatus 7.1.20540.2.2.1.1.10.1.1.6
The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

netDefaultGateway 7.1.20540.2.2.1.1.10.2
The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipHttpState 7.1.20540.2.2.1.1.10.3
Whether HTTP is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

ipHttpPort 7.1.20540.2.2.1.1.10.4
The port number for HTTP.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

ipDhcpRestart 7.1.20540.2.2.1.1.10.5
When set to restart(1) the DHCP server will restart. When read, this value always returns noRestart(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER restart(1), noRestart(2)  

ipHttpsState 7.1.20540.2.2.1.1.10.6
Whether HTTPS is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

ipHttpsPort 7.1.20540.2.2.1.1.10.7
The port number for HTTPS.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

dhcpMgt 7.1.20540.2.2.1.1.10.11
OBJECT IDENTIFIER    

dhcpClient 7.1.20540.2.2.1.1.10.11.1
OBJECT IDENTIFIER    

dhcpcOptions 7.1.20540.2.2.1.1.10.11.1.1
OBJECT IDENTIFIER    

dhcpcInterfaceTable 7.1.20540.2.2.1.1.10.11.1.1.1
Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN), or may have many entries(e.g. for all ports, or for all static VLANs).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpcInterfaceEntry

dhcpcInterfaceEntry 7.1.20540.2.2.1.1.10.11.1.1.1.1
Entry for DHCP client information listed by interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpcInterfaceEntry  

dhcpcIfIndex 7.1.20540.2.2.1.1.10.11.1.1.1.1.1
This is defined by ifIndex in the IF-MIB.(static vlan if index)
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

dhcpcIfClientIdMode 7.1.20540.2.2.1.1.10.11.1.1.1.1.2
Whether the Client ID is in text mode or in Hex mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSpecify(1), text(2), hex(3)  

dhcpcIfClientId 7.1.20540.2.2.1.1.10.11.1.1.1.1.3
The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identify the client.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

vlanTable 7.1.20540.2.2.1.1.12.1
Table for VLAN configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanEntry

vlanEntry 7.1.20540.2.2.1.1.12.1.1
Entry for VLAN configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanEntry  

vlanIndex 7.1.20540.2.2.1.1.12.1.1.1
Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vlanAddressMethod 7.1.20540.2.2.1.1.12.1.1.2
Method to get the IP address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER user(1), bootp(2), dhcp(3)  

vlanPortTable 7.1.20540.2.2.1.1.12.2
Table for port configuration in VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanPortEntry

vlanPortEntry 7.1.20540.2.2.1.1.12.2.1
Entry for port configuration in VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanPortEntry  

vlanPortIndex 7.1.20540.2.2.1.1.12.2.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDGE-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vlanPortMode 7.1.20540.2.2.1.1.12.2.1.2
This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hybrid(1), dot1qTrunk(2), access(3)  

vlanPortPrivateVlanType 7.1.20540.2.2.1.1.12.2.1.3
The port type defined for private VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), isolated(2), community(3), promiscous(4)  

protocolVlanTable 7.1.20540.2.2.1.1.12.5
The configuration table which contains the binding entry of the protocol-group and VLANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProtocolVlanEntry

protocolVlanEntry 7.1.20540.2.2.1.1.12.5.1
The binding entry of the protocol-group and VLANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProtocolVlanEntry  

protocolVlanGroupId 7.1.20540.2.2.1.1.12.5.1.1
The specified protocol group of a binding entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

protocolVlanGroupVid 7.1.20540.2.2.1.1.12.5.1.2
The vlan index of the binding entry. The vid zero is used to delete the binding entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

vlanDot1qTunnelGlobalConfig 7.1.20540.2.2.1.1.12.7
OBJECT IDENTIFIER    

vlanDot1qTunnelStatus 7.1.20540.2.2.1.1.12.7.1
This parameter is used to globally enable/disable 802.1Q Tunneling on the device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

vlanDot1qTunnelPortTable 7.1.20540.2.2.1.1.12.8
Table for port configuration in 802.1Q Tunneling.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanDot1qTunnelPortEntry

vlanDot1qTunnelPortEntry 7.1.20540.2.2.1.1.12.8.1
Entry for port configuration in 802.1Q Tunneling.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanDot1qTunnelPortEntry  

vlanDot1qTunnelPortIndex 7.1.20540.2.2.1.1.12.8.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vlanDot1qTunnelPortMode 7.1.20540.2.2.1.1.12.8.1.2
This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to dot1qTunnel(2) sets as dot1q-tunnel mode port which link to customer. Setting it to dot1qTunnelUplink(3) sets as dot1q-tunnel mode port which link to service-provider. If vlanDot1qTunnelStatus is disabled, it means vlanDot1qTunnelPortMode is inactive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), dot1qTunnel(2), dot1qTunnelUplink(3)  

vlanDot1qTunnelPortEtherType 7.1.20540.2.2.1.1.12.8.1.3
TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0800..ffff  

voiceVlanMgt 7.1.20540.2.2.1.1.12.6
OBJECT IDENTIFIER    

voiceVlanOuiTable 7.1.20540.2.2.1.1.12.6.1
A table containing the mac address which can be identified by voice vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceVlanOuiEntry

voiceVlanOuiEntry 7.1.20540.2.2.1.1.12.6.1.1
A table containing the mac address which can be identified by voice vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoiceVlanOuiEntry  

voiceVlanOuiAddress 7.1.20540.2.2.1.1.12.6.1.1.1
MAC address can be identified by voice vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

voiceVlanOuiMask 7.1.20540.2.2.1.1.12.6.1.1.2
The mask of MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

voiceVlanOuiDescription 7.1.20540.2.2.1.1.12.6.1.1.3
The description of oui.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..30)  

voiceVlanOuiStatus 7.1.20540.2.2.1.1.12.6.1.1.4
Current operation status of the row.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

voiceVlanEnabledId 7.1.20540.2.2.1.1.12.6.2
Voice vlan enable status: enabled (2..4095), disabled (-1).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

voiceVlanAgingTime 7.1.20540.2.2.1.1.12.6.3
Voice vlan aging time, the unit of which is minute.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..43200  

voiceVlanPortTable 7.1.20540.2.2.1.1.12.6.7
A list of voice vlan mode entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceVlanPortEntry

voiceVlanPortEntry 7.1.20540.2.2.1.1.12.6.7.1
An entry containing voice vlan mode information, which is applicable to a voice vlan enabled interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoiceVlanPortEntry  

voiceVlanPortIfIndex 7.1.20540.2.2.1.1.12.6.7.1.1
The index of interface on which voice vlan function is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

voiceVlanPortMode 7.1.20540.2.2.1.1.12.6.7.1.2
Voice vlan configuration mode status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), manual(2), none(3)  

voiceVlanPortSecurity 7.1.20540.2.2.1.1.12.6.7.1.3
If the security is enabled, the port is only allow voice traffuc for the voice vlan.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

voiceVlanPortPriority 7.1.20540.2.2.1.1.12.6.7.1.4
The priority of the voice vlan traffic in the port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..6  

voiceVlanPortRuleOui 7.1.20540.2.2.1.1.12.6.7.1.5
The address of voice device is learned from Oui table.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

voiceVlanPortRuleLldp 7.1.20540.2.2.1.1.12.6.7.1.6
The address of voice device is learned from LLDP discovery.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

macVlanTable 7.1.20540.2.2.1.1.12.11
A table that contains the settings for MAC-based VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacVlanEntry

macVlanEntry 7.1.20540.2.2.1.1.12.11.1
A conceptual row in the macVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacVlanEntry  

macVlanMacAddress 7.1.20540.2.2.1.1.12.11.1.1
The MAC address that may specify an entry in the table which contains MAC-based VLAN information.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

macVlanId 7.1.20540.2.2.1.1.12.11.1.2
Specifies the VLAN ID which the MAC address associates with.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4092  

macVlanStatus 7.1.20540.2.2.1.1.12.11.1.4
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

macVlanClearAction 7.1.20540.2.2.1.1.12.12
Action for clearing macVlanTable. When this object is set to clear(2), all entries in macVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

subnetVlanTable 7.1.20540.2.2.1.1.12.13
A table that contains the settings for IP subnet-based VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubnetVlanEntry

subnetVlanEntry 7.1.20540.2.2.1.1.12.13.1
A conceptual row in the subnetVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SubnetVlanEntry  

subnetVlanIpAddress 7.1.20540.2.2.1.1.12.13.1.1
The IPv4 address of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanMask object is not equal to x.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

subnetVlanMask 7.1.20540.2.2.1.1.12.13.1.2
The netmask of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanIpAddress object is not equal to subnetVlanIpAddress.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

subnetVlanId 7.1.20540.2.2.1.1.12.13.1.3
Specifies the VLAN ID which the subnet associates with.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4094  

subnetVlanPriority 7.1.20540.2.2.1.1.12.13.1.4
Specifies the priority whcich the subnet associates with.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

subnetVlanStatus 7.1.20540.2.2.1.1.12.13.1.5
Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

subnetVlanClearAction 7.1.20540.2.2.1.1.12.14
Action for clearing subnetVlanTable. When this object is set to clear(2), all entries in subnetVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

prioIpPrecDscpStatus 7.1.20540.2.2.1.1.13.1
Selects whether no frame priority mapping, IP ToS precedence mapping or DSCP mapping is performed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), precedence(2), dscp(3)  

prioIpDscpTable 7.1.20540.2.2.1.1.13.4
Table for IP DSCP priority mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrioIpDscpEntry

prioIpDscpEntry 7.1.20540.2.2.1.1.13.4.1
Entry for IP DSCP priority mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrioIpDscpEntry  

prioIpDscpPort 7.1.20540.2.2.1.1.13.4.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

prioIpDscpValue 7.1.20540.2.2.1.1.13.4.1.2
Value of IP DSCP as specified in the packet header.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

prioIpDscpCos 7.1.20540.2.2.1.1.13.4.1.3
Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of Service (CoS). This CoS is then further mapped to the hardware queue according to dot1dTrafficClassTable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

prioIpDscpRestoreDefault 7.1.20540.2.2.1.1.13.5
Enables the IP DSCP settings of a port to be reset to their defaults. To reset the IP DSCP settings of a port, assign the value of the relevant ifIndex defined by the ifIndex in the IF-MIB. For example, assigning the value 1 will result in the IP DSCP settings of port 1 being restored to their default. 0 will always be obtained when reading this variable
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

prioCopy 7.1.20540.2.2.1.1.13.8
OBJECT IDENTIFIER    

prioCopyIpDscp 7.1.20540.2.2.1.1.13.8.2
Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port in high-to-low (big-endian) order. Starting from the 5th octet is the destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

prioWrrTable 7.1.20540.2.2.1.1.13.9
Table for weighted round robin (WRR).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrioWrrEntry

prioWrrEntry 7.1.20540.2.2.1.1.13.9.1
Entry for weighted round robin (WRR).
Status: current Access: not-accessible
OBJECT-TYPE    
  PrioWrrEntry  

prioWrrTrafficClass 7.1.20540.2.2.1.1.13.9.1.1
Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7  

prioWrrWeight 7.1.20540.2.2.1.1.13.9.1.2
Weight for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

prioQueueMode 7.1.20540.2.2.1.1.13.10
The global status for the prioQueue. wrr(1),strict(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER wrr(1), strict(2)  

trapDestTable 7.1.20540.2.2.1.1.14.1
A list of trap destination entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

trapDestEntry 7.1.20540.2.2.1.1.14.1.1
A destination entry describes the destination IP address, the community string, and SNMP version to use when sending a trap.
Status: current Access: not-accessible
OBJECT-TYPE    
  TrapDestEntry  

trapDestAddress 7.1.20540.2.2.1.1.14.1.1.1
The address to send traps.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

trapDestCommunity 7.1.20540.2.2.1.1.14.1.1.2
A community to which this destination address belongs.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

trapDestStatus 7.1.20540.2.2.1.1.14.1.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

trapDestVersion 7.1.20540.2.2.1.1.14.1.1.4
Determines the version of the trap that is to be sent to the trap receiver. If the value is 1, then an SNMP version 1 trap is sent and if the value is 2, an SNMP version 2 trap is sent.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER version1(1), version2(2)  

trapDestUdpPort 7.1.20540.2.2.1.1.14.1.1.5
Determines the UDP port number that the trap will be sent to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

trapVar 7.1.20540.2.2.1.1.14.2
OBJECT IDENTIFIER    

trapVarLoginUserName 7.1.20540.2.2.1.1.14.2.11
The name of the user who logs into the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(1..8)  

trapVarLoginMethod 7.1.20540.2.2.1.1.14.2.12
The method by which the user logs in to control the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER web(1), snmp(2), telnet(3), console(4)  

trapVarLoginIPAddress 7.1.20540.2.2.1.1.14.2.13
The IP address from which the user logs into the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

trapVarLoginTime 7.1.20540.2.2.1.1.14.2.14
The date and time when the user logs into the switch. The format of this variables follows that of sysCurrentTime in this MIB file.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(20)  

trapAutoUpgradeResult 7.1.20540.2.2.1.1.14.2.18
The parameter indicates which result triggers the trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER succeeded(1), failed(2)  

trapAutoUpgradeNewVer 7.1.20540.2.2.1.1.14.2.19
The parameter indicates new version which was upgraded to. When trapAutoUpgradeResult was failed(2), it would be null string.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..20)  

rateLimitMgt 7.1.20540.2.2.1.1.16.1
OBJECT IDENTIFIER    

rateLimitPortTable 7.1.20540.2.2.1.1.16.1.2
Table for rate limit of each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RateLimitPortEntry

rateLimitPortEntry 7.1.20540.2.2.1.1.16.1.2.1
Entry for rate limit of each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  RateLimitPortEntry  

rlPortIndex 7.1.20540.2.2.1.1.16.1.2.1.1
The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

rlPortInputStatus 7.1.20540.2.2.1.1.16.1.2.1.6
Whether input rate limit is enabled for this port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

rlPortOutputStatus 7.1.20540.2.2.1.1.16.1.2.1.7
Whether output rate limit is enabled for this port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

rlPortInputLimitInKilo 7.1.20540.2.2.1.1.16.1.2.1.10
Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

rlPortOutputLimitInKilo 7.1.20540.2.2.1.1.16.1.2.1.11
Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServMgt 7.1.20540.2.2.1.1.16.4
OBJECT IDENTIFIER    

diffServPortTable 7.1.20540.2.2.1.1.16.4.9
Table for differentiated services on each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPortEntry

diffServPortEntry 7.1.20540.2.2.1.1.16.4.9.1
Entry for differentiated services on each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServPortEntry  

diffServPortIfIndex 7.1.20540.2.2.1.1.16.4.9.1.1
This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServPortPolicyMapIndex 7.1.20540.2.2.1.1.16.4.9.1.2
Specifies the policy map binding to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPortIngressIpAclIndex 7.1.20540.2.2.1.1.16.4.9.1.3
Specifies the ingress IP ACL binding to the interface. The ingress IP ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPortIngressMacAclIndex 7.1.20540.2.2.1.1.16.4.9.1.4
Specifies the ingress MAC ACL binding to the interface. The ingress MAC ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPortIngressIpv6AclIndex 7.1.20540.2.2.1.1.16.4.9.1.5
Specifies the ingress IPv6 ACL binding to the interface. The ingress IPv6 ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPolicyMapTable 7.1.20540.2.2.1.1.16.4.10
Table for policy map.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPolicyMapEntry

diffServPolicyMapEntry 7.1.20540.2.2.1.1.16.4.10.1
Entry for policy map.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServPolicyMapEntry  

diffServPolicyMapIndex 7.1.20540.2.2.1.1.16.4.10.1.1
An index that uniquely identifies an entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServPolicyMapName 7.1.20540.2.2.1.1.16.4.10.1.2
The name of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServPolicyMapDescription 7.1.20540.2.2.1.1.16.4.10.1.3
The description of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

diffServPolicyMapElementIndexList 7.1.20540.2.2.1.1.16.4.10.1.4
The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

diffServPolicyMapStatus 7.1.20540.2.2.1.1.16.4.10.1.5
This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active');it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServPolicyMapAttachCtl 7.1.20540.2.2.1.1.16.4.11
OBJECT IDENTIFIER    

diffServPolicyMapAttachCtlIndex 7.1.20540.2.2.1.1.16.4.11.1
Index for attachment control. Specifies the policy map as the target to relate with the policy map element. The policy map identified by a particular value of this index is associated with the same diffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPolicyMapAttachCtlElementIndex 7.1.20540.2.2.1.1.16.4.11.2
Element Index for attachment control.Specifies the policy map element to relate with the policy map. The policy map element identified by a particular value of this index is associated with the same diffServPolicyMapElementEntry as identified by the same value of diffServPolicyMapElementIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServPolicyMapAttachCtlAction 7.1.20540.2.2.1.1.16.4.11.3
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular policy map element is attached to a particular policy map. When setting this object to detach(3) to begin the not attached operation, a particular policy map element is not attached to a particular policy map. When the action is finshed or no action is taken, the value of this object is noAction(1). A particular policy map is specified in the diffServPolicyMapAttachCtlIndex. A particularpolicy map element is specified in the diffServPolicyMapAttachCtlElementIndex.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServPolicyMapElementTable 7.1.20540.2.2.1.1.16.4.12
Table for policy map element.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServPolicyMapElementEntry

diffServPolicyMapElementEntry 7.1.20540.2.2.1.1.16.4.12.1
Entry for policy map element.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServPolicyMapElementEntry  

diffServPolicyMapElementIndex 7.1.20540.2.2.1.1.16.4.12.1.1
An index that uniquely identifies an entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServPolicyMapElementClassMapIndex 7.1.20540.2.2.1.1.16.4.12.1.2
Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

diffServPolicyMapElementMeterIndex 7.1.20540.2.2.1.1.16.4.12.1.3
Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is zero, no associated meter will be associated, as zero is not a valid meter index.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

diffServPolicyMapElementActionIndex 7.1.20540.2.2.1.1.16.4.12.1.4
Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

diffServPolicyMapElementStatus 7.1.20540.2.2.1.1.16.4.12.1.5
This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServClassMapTable 7.1.20540.2.2.1.1.16.4.13
Table for class map.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServClassMapEntry

diffServClassMapEntry 7.1.20540.2.2.1.1.16.4.13.1
Entry for class map.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServClassMapEntry  

diffServClassMapIndex 7.1.20540.2.2.1.1.16.4.13.1.1
An index that uniquely identifies an entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServClassMapName 7.1.20540.2.2.1.1.16.4.13.1.2
The name of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServClassMapDescription 7.1.20540.2.2.1.1.16.4.13.1.3
The description of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

diffServClassMapMatchType 7.1.20540.2.2.1.1.16.4.13.1.4
The map match type of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER matchAny(1), matchAll(2)  

diffServClassMapElementIndexTypeList 7.1.20540.2.2.1.1.16.4.13.1.5
The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element index in network order and it maps the index of differServClasssMapElementIndexList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServClassMapElementIndexList 7.1.20540.2.2.1.1.16.4.13.1.6
The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the particular class map elements which belong to this table. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is two octet specified in differServClasssMapElementIndexTypeList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServClassMapStatus 7.1.20540.2.2.1.1.16.4.13.1.7
This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServClassMapAttachCtl 7.1.20540.2.2.1.1.16.4.14
OBJECT IDENTIFIER    

diffServClassMapAttachCtlIndex 7.1.20540.2.2.1.1.16.4.14.1
Index for attachment control. Specifies the class map as the target to relate with class map elements. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServClassMapAttachCtlElementIndexType 7.1.20540.2.2.1.1.16.4.14.2
Element Index for attachment control. Specifies the type of class map element to relate with the class map. When type is macAce(1), the index of diffServClassMapAttachCtlElementIndex is the index of diffServMacAceEntry. When the type is ipAce(2), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpAceEntry. When the type is acl(3), the index of diffServClassMapAttachCtlElementIndex is the index of diffServAclEntry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macAce(1), ipAce(2), acl(3)  

diffServClassMapAttachCtlElementIndex 7.1.20540.2.2.1.1.16.4.14.3
Element Index for attachment control. Specifies the class map element related with the class map. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is specified in diffServClassMapAttachCtlElementIndexType. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServClassMapAttachCtlAction 7.1.20540.2.2.1.1.16.4.14.4
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular class map element is attached to a particular class map. When setting this object to detach(3) to begin the not attached operation, then a particular class map element is not attached to a particular class map. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1). The value of a particular class map is specified in the AclAttachCtlTargetIndex. The class map element is specified by diffServClassMapAttachCtlElementIndexType and diffServClassMapAttachCtlElementIndex.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServAclTable 7.1.20540.2.2.1.1.16.4.15
Table for ACL.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServAclEntry

diffServAclEntry 7.1.20540.2.2.1.1.16.4.15.1
Entry for ACL.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServAclEntry  

diffServAclIndex 7.1.20540.2.2.1.1.16.4.15.1.1
An index that uniquely identifies an entry in the ACL table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServAclName 7.1.20540.2.2.1.1.16.4.15.1.2
The name of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..16)  

diffServAclType 7.1.20540.2.2.1.1.16.4.15.1.3
The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry will be aoto- unbound from the diffServPortTable and the diffServClassMapTable.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER mac(1), ipstandard(2), ipextended(3), ipv6standard(4), ipv6extended(5)  

diffServAclAceIndexList 7.1.20540.2.2.1.1.16.4.15.1.4
The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs which belong to this table. The ACE uses type to indicate the diffServIpAceEntry, the diffServMacAceEntry or the diffServIpv6AceEntry. The type is specified in diffServAclType. When the type is macAce(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipAce(2), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6Ace(3), the index of diffServAclAceIndexListis the diffServIpv6AceEntry.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

diffServAclStatus 7.1.20540.2.2.1.1.16.4.15.1.5
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServAclAttachCtl 7.1.20540.2.2.1.1.16.4.16
OBJECT IDENTIFIER    

diffServAclAttachCtlIndex 7.1.20540.2.2.1.1.16.4.16.1
Index for attachment control. Specifies the ACL as the target to relate with the IP ACE, the MAC ACE or IPv6 ACE. The ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServAclAttachCtlAceType 7.1.20540.2.2.1.1.16.4.16.2
Type for attachment control. Specifies the type of diffServAclAttachCtlAceIndex to relate with the diffServAclAttachCtlIndex. When the type is macAce(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipAce(2), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6Ace(3), the index of diffServAclAceIndexList is the diffServIpv6AceEntry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macAce(1), ipAce(2), ipv6Ace(3)  

diffServAclAttachCtlAceIndex 7.1.20540.2.2.1.1.16.4.16.3
Index for attachment control. Specifies the ACE to relate with the diffServAclAttachCtlIndex. When diffServAclAttachCtlAceType is macAce(1), the value of diffServAclAttachCtlIndex is the diffServMacAceEntry. When diffServAclAttachCtlAceType is ipAce(2), the value of diffServAclAttachCtlIndex is the diffServIpAceEntry. When diffServAclAttachCtlAceType is ipv6Ace(3), the value of diffServAclAttachCtlIndex is the diffServIpv6AceEntry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

diffServAclAttachCtlAction 7.1.20540.2.2.1.1.16.4.16.4
Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When setting this object to detach(3) to begin the not attached operation, then a particular ACE is not attached to a particular ACL. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1), The value of a particular ACL is specified in the diffServAclAttachCtlAceType and diffServAclAttachCtlAceIndex.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), attach(2), detach(3)  

diffServIpAceTable 7.1.20540.2.2.1.1.16.4.17
Table for IP ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServIpAceEntry

diffServIpAceEntry 7.1.20540.2.2.1.1.16.4.17.1
Entry for IP ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServIpAceEntry  

diffServIpAceIndex 7.1.20540.2.2.1.1.16.4.17.1.1
An index that uniquely identifies an entry in the IP ACE table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServIpAceType 7.1.20540.2.2.1.1.16.4.17.1.2
The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER standard(1), extended(2)  

diffServIpAceAccess 7.1.20540.2.2.1.1.16.4.17.1.3
Indicates the action to be taken if a packet matches this ACE.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

diffServIpAceSourceIpAddr 7.1.20540.2.2.1.1.16.4.17.1.4
The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this object.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

diffServIpAceSourceIpAddrBitmask 7.1.20540.2.2.1.1.16.4.17.1.5
The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this object.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

diffServIpAceDestIpAddr 7.1.20540.2.2.1.1.16.4.17.1.6
The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the value of this object. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

diffServIpAceDestIpAddrBitmask 7.1.20540.2.2.1.1.16.4.17.1.7
The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

diffServIpAceProtocol 7.1.20540.2.2.1.1.16.4.17.1.8
The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..256  

diffServIpAcePrec 7.1.20540.2.2.1.1.16.4.17.1.9
Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..8  

diffServIpAceTos 7.1.20540.2.2.1.1.16.4.17.1.10
Specifies the IP ToS facility value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 9. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

diffServIpAceDscp 7.1.20540.2.2.1.1.16.4.17.1.11
Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..64  

diffServIpAceSourcePortOp 7.1.20540.2.2.1.1.16.4.17.1.12
Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the source TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinSourcePort to match against. range(3),which is used the diffServIpAceMinSourcePort and the diffServIpAceMaxSourcePort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServIpAceMinSourcePort 7.1.20540.2.2.1.1.16.4.17.1.13
If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceSourcePortBitmask 7.1.20540.2.2.1.1.16.4.17.1.15
If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceDestPortOp 7.1.20540.2.2.1.1.16.4.17.1.16
Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinDestPort to match against. range(3),which is used the diffServIpAceMinDestPort and the diffServIpAceMaxDestPort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServIpAceMinDestPort 7.1.20540.2.2.1.1.16.4.17.1.17
If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceDestPortBitmask 7.1.20540.2.2.1.1.16.4.17.1.19
If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServIpAceControlCode 7.1.20540.2.2.1.1.16.4.17.1.20
Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

diffServIpAceControlCodeBitmask 7.1.20540.2.2.1.1.16.4.17.1.21
Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4, PSH=8, ACK=16, URG=32. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

diffServIpAceStatus 7.1.20540.2.2.1.1.16.4.17.1.22
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServMacAceTable 7.1.20540.2.2.1.1.16.4.18
Table for MAC ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServMacAceEntry

diffServMacAceEntry 7.1.20540.2.2.1.1.16.4.18.1
Entry for MAC ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServMacAceEntry  

diffServMacAceIndex 7.1.20540.2.2.1.1.16.4.18.1.1
An index that uniquely identifies an entry in the MAC ACE table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServMacAceAccess 7.1.20540.2.2.1.1.16.4.18.1.2
Indicates the action to be taken if a packet matches this ACE.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

diffServMacAcePktformat 7.1.20540.2.2.1.1.16.4.18.1.3
Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), untagged-Eth2(2), untagged802Dot3(3), tagggedEth2(4), tagged802Dot3(5)  

diffServMacAceSourceMacAddr 7.1.20540.2.2.1.1.16.4.18.1.4
Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSourceMacAddrBitmask and then compared against the value of this object.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

diffServMacAceSourceMacAddrBitmask 7.1.20540.2.2.1.1.16.4.18.1.5
The specified source MAC address mask.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

diffServMacAceDestMacAddr 7.1.20540.2.2.1.1.16.4.18.1.6
Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of diffServMacAceDestMacAddrBitmask and then compared against the value of this object.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

diffServMacAceDestMacAddrBitmask 7.1.20540.2.2.1.1.16.4.18.1.7
The specified destination MAC address mask.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

diffServMacAceVidOp 7.1.20540.2.2.1.1.16.4.18.1.8
Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceMinVid 7.1.20540.2.2.1.1.16.4.18.1.9
Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4094  

diffServMacAceVidBitmask 7.1.20540.2.2.1.1.16.4.18.1.10
The bit mask of the VID. The default value is 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..0FFF  

diffServMacAceEtherTypeOp 7.1.20540.2.2.1.1.16.4.18.1.12
Indicates how a packet's ether type is to be compared.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceEtherTypeBitmask 7.1.20540.2.2.1.1.16.4.18.1.13
The bit mask of Ether type. The default value is 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..FFFF  

diffServMacAceMinEtherType 7.1.20540.2.2.1.1.16.4.18.1.14
Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0000..FFFF  

diffServMacAceStatus 7.1.20540.2.2.1.1.16.4.18.1.16
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServMacAceCosOp 7.1.20540.2.2.1.1.16.4.18.1.17
Indicates how a packet's CoS is compared. If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing, and diffServMacAceCosBitmask is used as the bitmask of the CoS value. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos should be used as the lower bound of the CoS value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noOperator(1), equal(2), range(3)  

diffServMacAceCosBitmask 7.1.20540.2.2.1.1.16.4.18.1.18
Indicates the bitmask of the CoS value if the object type of diffServMacAceCosOp is equal(2). The default value is 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

diffServMacAceMinCos 7.1.20540.2.2.1.1.16.4.18.1.19
If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos indicates the lower bound of the CoS value.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

diffServActionTable 7.1.20540.2.2.1.1.16.4.19
Table for action.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServActionEntry

diffServActionEntry 7.1.20540.2.2.1.1.16.4.19.1
Entry for action.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServActionEntry  

diffServActionIndex 7.1.20540.2.2.1.1.16.4.19.1.1
An index that uniquely identifies an entry in the action table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServActionList 7.1.20540.2.2.1.1.16.4.19.1.2
The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri and actionPktNewDscp can not be enabled at the same time on the entry. The actionRedPktNewDscp and actionRedDrop can not be enabled at the same time on the entry.
Status: current Access: read-create
OBJECT-TYPE    
  BITS actionPktNewPri(0), actionPktNewDscp(2), actionRedPktNewDscp(3), actionRedDrop(4)  

diffServActionPktNewPri 7.1.20540.2.2.1.1.16.4.19.1.3
Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object can not be set.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

diffServActionPktNewDscp 7.1.20540.2.2.1.1.16.4.19.1.5
Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

diffServActionRedPktNewDscp 7.1.20540.2.2.1.1.16.4.19.1.6
Specifies the new DSCP value for the red marking packet when the action is satisfied. If the actionRedPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

diffServActionRedDrop 7.1.20540.2.2.1.1.16.4.19.1.7
The actionRedDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

diffServActionStatus 7.1.20540.2.2.1.1.16.4.19.1.8
This object is used to create a new row, modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServMeterTable 7.1.20540.2.2.1.1.16.4.20
Table for meter.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServMeterEntry

diffServMeterEntry 7.1.20540.2.2.1.1.16.4.20.1
Entry for meter.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServMeterEntry  

diffServMeterIndex 7.1.20540.2.2.1.1.16.4.20.1.1
An entry that describes a single set of token bucket parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServMeterModel 7.1.20540.2.2.1.1.16.4.20.1.2
The Metering algorithm associated with the Token Bucket parameters. The zeroDotZero indicates this is unknown.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), flow(2), trTcmColorBlind(3), trTcmColorAware(4), srTcmColorBlind(5), srTcmColorAware(6)  

diffServMeterRate 7.1.20540.2.2.1.1.16.4.20.1.3
The token-bucket rate, in kilobits per second (kbps).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000  

diffServMeterBurstSize 7.1.20540.2.2.1.1.16.4.20.1.4
The maximum number of bytes in a single transmission burst.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 64..524288  

diffServMeterInterval 7.1.20540.2.2.1.1.16.4.20.1.5
The time interval used with the token bucket.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

diffServMeterStatus 7.1.20540.2.2.1.1.16.4.20.1.6
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

diffServIpv6AceTable 7.1.20540.2.2.1.1.16.4.21
Table for IPv6 ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DiffServIpv6AceEntry

diffServIpv6AceEntry 7.1.20540.2.2.1.1.16.4.21.1
Entry fo IPv6 ACE.
Status: current Access: not-accessible
OBJECT-TYPE    
  DiffServIpv6AceEntry  

diffServIpv6AceIndex 7.1.20540.2.2.1.1.16.4.21.1.1
An index that uniquely identifies an entry in the IPv6 table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

diffServIpv6AceType 7.1.20540.2.2.1.1.16.4.21.1.2
The specified IP v6 ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER standard(1), extended(2)  

diffServIpv6AceAccess 7.1.20540.2.2.1.1.16.4.21.1.3
Indicates the action to be taken if a packet matches this ACE.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

diffServIpv6AceSourceIpAddr 7.1.20540.2.2.1.1.16.4.21.1.4
Specifies the source IPv6 address.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

diffServIpv6AceSourceIpAddrPrefixLen 7.1.20540.2.2.1.1.16.4.21.1.5
The length (in bits) associated with the source IPv6 address prefix of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..128  

diffServIpv6AceDestIpAddr 7.1.20540.2.2.1.1.16.4.21.1.6
Specifies the destination IPv6 address. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

diffServIpv6AceDestIpAddrPrefixLen 7.1.20540.2.2.1.1.16.4.21.1.7
The length (in bits) associated with the destination IPv6 address prefix of this entry. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..8  

diffServIpv6AceDscp 7.1.20540.2.2.1.1.16.4.21.1.9
Specifies the DSCP value to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..64  

diffServIpv6AceStatus 7.1.20540.2.2.1.1.16.4.21.1.11
This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

privateVlanMgt 7.1.20540.2.2.1.1.17.1
OBJECT IDENTIFIER    

portSecurityMgt 7.1.20540.2.2.1.1.17.2
OBJECT IDENTIFIER    

radiusMgt 7.1.20540.2.2.1.1.17.4
OBJECT IDENTIFIER    

tacacsMgt 7.1.20540.2.2.1.1.17.5
OBJECT IDENTIFIER    

sshMgt 7.1.20540.2.2.1.1.17.6
OBJECT IDENTIFIER    

ipFilterMgt 7.1.20540.2.2.1.1.17.9
OBJECT IDENTIFIER    

dot1xMgt 7.1.20540.2.2.1.1.17.11
OBJECT IDENTIFIER    

aaaMgt 7.1.20540.2.2.1.1.17.12
OBJECT IDENTIFIER    

networkAccessMgt 7.1.20540.2.2.1.1.17.13
OBJECT IDENTIFIER    

macAuthMgt 7.1.20540.2.2.1.1.17.14
OBJECT IDENTIFIER    

webAuthMgt 7.1.20540.2.2.1.1.17.15
OBJECT IDENTIFIER    

privateVlanStatus 7.1.20540.2.2.1.1.17.1.1
This controls whether private VLAN is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

privateVlanVlanTable 7.1.20540.2.2.1.1.17.1.4
A table containing private VLAN information on the VLANs which currently exist.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanVlanEntry

privateVlanVlanEntry 7.1.20540.2.2.1.1.17.1.4.1
A conceptual row containing the private VLAN information on the VLANs for a particular management domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivateVlanVlanEntry  

privateVlanVlanIndex 7.1.20540.2.2.1.1.17.1.4.1.1
The VLAN ID of this private VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

privateVlanVlanType 7.1.20540.2.2.1.1.17.1.4.1.2
The VLAN type as defined for Private VLAN feature. Set the value to invalid(1) to destroy an entry. Set other values to create an entry. If an index already exists, set others to modifiy it. Note that a VLAN's private VLAN type cannot be changed once it has any port members.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invalid(1), primary(2), isolated(3), community(4)  

privateVlanAssoicatedPrimaryVlan 7.1.20540.2.2.1.1.17.1.4.1.3
The VLAN ID of the associated primary VLAN used for the private VLAN feature if privateVlanVlanType has the value of isolated(3), community(4). If privateVlanVlanType has the value of primary(2), then this object has the value of 0. Note that one isolated VLAN can only be associated with one unique primary VLAN. One primary VLAN can only be associated with one isolated VLAN. One primary VLAN can be associated with multiple community VLANs; one community VLAN can only be associated with one unique primary VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4094  

privateVlanPrivatePortTable 7.1.20540.2.2.1.1.17.1.5
A table containing information on the configuration of secondary VLANs on the device ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanPrivatePortEntry

privateVlanPrivatePortEntry 7.1.20540.2.2.1.1.17.1.5.1
A conceptual row containing information of the configuration of secondary VLANs for each port. An entry is created by the managed system for each interface which can be configured as a private port for Private VLAN feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivateVlanPrivatePortEntry  

privateVlanPrivatePortIfIndex 7.1.20540.2.2.1.1.17.1.5.1.1
This is defined as the ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

privateVlanPrivatePortSecondaryVlan 7.1.20540.2.2.1.1.17.1.5.1.2
The VLAN ID of the secondary VLAN configured on this private port. A private port is a port that allows ingress traffic of the secondary VLAN as well as egress traffic of its associated primary VLAN, but blocks the egress traffic of the isolated VLAN while allowing the egress traffic of the community or twoWayCommunity VLAN depending on the type of the secondary VLAN. Note that a port can join a secondary VLAN only after this secondary VLAN has been associated with a primary VLAN, i.e., the cpvlanVlanAssociatedPrimaryVlan has a non-zero value. The default value of 0 for this object means this port has not yet joined a secondary VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4094  

privateVlanPromPortTable 7.1.20540.2.2.1.1.17.1.6
A table containing secondary VLAN to primary VLAN remapping information on ports of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanPromPortEntry

privateVlanPromPortEntry 7.1.20540.2.2.1.1.17.1.6.1
A conceptual row containing secondary VLAN to primary VLAN remapping information for each port. An entry is created by the managed system for each interface which can be configured as a promiscuous port for the private VLAN feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivateVlanPromPortEntry  

privateVlanPromPortIfIndex 7.1.20540.2.2.1.1.17.1.6.1.1
This is defined as ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

privateVlanPromPortPrimaryVlanId 7.1.20540.2.2.1.1.17.1.6.1.2
The primary VLAN ID of the promiscous port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4094  

privateVlanPromPortSecondaryRemap 7.1.20540.2.2.1.1.17.1.6.1.3
A string of octets containing one bit per VLAN in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

privateVlanPromPortSecondaryRemap2k 7.1.20540.2.2.1.1.17.1.6.1.4
A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 1024 through 2047 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

privateVlanPromPortSecondaryRemap3k 7.1.20540.2.2.1.1.17.1.6.1.5
A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 2048 through 3071 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

privateVlanPromPortSecondaryRemap4k 7.1.20540.2.2.1.1.17.1.6.1.6
A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 3072 through 4095 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

privateVlanSessionTable 7.1.20540.2.2.1.1.17.1.8
Contains the settings for private VLAN Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanSessionEntry

privateVlanSessionEntry 7.1.20540.2.2.1.1.17.1.8.1
A conceptual row in the privateVlanSession table.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrivateVlanSessionEntry  

privateVlanSessionId 7.1.20540.2.2.1.1.17.1.8.1.1
The session ID that may specifiy certain entry in the table which contains private VLAN session information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

privateVlanSessionUplinkPorts 7.1.20540.2.2.1.1.17.1.8.1.2
This is the list of uplink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortDownlink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

privateVlanSessionDownlinkPorts 7.1.20540.2.2.1.1.17.1.8.1.3
This is the list of downlink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortUplink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

privateVlanSessionStatus 7.1.20540.2.2.1.1.17.1.8.1.4
Set this to valid(1) to create an entry. Sets this to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  


portSecPortTable 7.1.20540.2.2.1.1.17.2.1
The port security(MAC binding) Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecPortEntry

portSecPortEntry 7.1.20540.2.2.1.1.17.2.1.1
The entry of portSecPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortSecPortEntry  

portSecPortIndex 7.1.20540.2.2.1.1.17.2.1.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

portSecPortStatus 7.1.20540.2.2.1.1.17.2.1.1.2
Set enabled(1) to enable port security and set disabled(2) to disable port security.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

portSecAction 7.1.20540.2.2.1.1.17.2.1.1.3
The corresponding actions that will take place when a port is under intrusion, when this variable is set to none(1), no action will be performed, when this variable is set to trap(2), a swPortSecurityTrap trap will be sent, when this variable is set to shutdown(3), the port will shutdown, when this variable is set to trapAndShutdown(4), a swPortSecurityTrap will be sent and the port will shutdown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), trap(2), shutdown(3), trapAndShutdown(4)  

portSecMaxMacCount 7.1.20540.2.2.1.1.17.2.1.1.4
The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will discard all secure MAC and begin to learn again, until the number of MAC has reached this value, and only the secure MAC addresses can enter this port. If the portSecPortStatus is disabled, we will begin to learn the MAC, and auto enabled the portSecPortStatus when the MAC has reached this value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1024  

radiusServerGlobalAuthPort 7.1.20540.2.2.1.1.17.4.1
Aauthentication port number for RADIUS server. When specified radius server do not set aauthentication port number, this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerGlobalAcctPort 7.1.20540.2.2.1.1.17.4.2
Accounting port number of RADIUS server. When specified radius server do not set accounting port number, this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerGlobalKey 7.1.20540.2.2.1.1.17.4.3
Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. When specified radius server do not set key, this this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

radiusServerGlobalRetransmit 7.1.20540.2.2.1.1.17.4.4
Maximum number of retransmissions for RADIUS. When specified radius server do not set maximum number of retransmissions, this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

radiusServerGlobalTimeout 7.1.20540.2.2.1.1.17.4.5
Timeout for RADIUS. When specified radius server do not set timeout, this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerTable 7.1.20540.2.2.1.1.17.4.7
The table for RADIUS server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusServerEntry

radiusServerEntry 7.1.20540.2.2.1.1.17.4.7.1
The conceptual row for radiusServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadiusServerEntry  

radiusServerIndex 7.1.20540.2.2.1.1.17.4.7.1.1
The RADIUS server index in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

radiusServerAddress 7.1.20540.2.2.1.1.17.4.7.1.2
IP address of a RADIUS server.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

radiusServerAuthPortNumber 7.1.20540.2.2.1.1.17.4.7.1.3
Authentication port number of RADIUS server.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerAcctPortNumber 7.1.20540.2.2.1.1.17.4.7.1.4
Accounting port number of RADIUS server.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerKey 7.1.20540.2.2.1.1.17.4.7.1.5
Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

radiusServerRetransmit 7.1.20540.2.2.1.1.17.4.7.1.6
Timeout for RADIUS.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

radiusServerTimeout 7.1.20540.2.2.1.1.17.4.7.1.7
Timeout for RADIUS.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

radiusServerStatus 7.1.20540.2.2.1.1.17.4.7.1.8
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

tacacsPlusServerGlobalPortNumber 7.1.20540.2.2.1.1.17.5.2
TCP port number of TACACS+ server. When specified TACACS+ server do not set TCP port number, this this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

tacacsPlusServerGlobalKey 7.1.20540.2.2.1.1.17.5.3
The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string.When specified TACACS+ server do not set the encryption key , this this value is used.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

tacacsPlusServerTable 7.1.20540.2.2.1.1.17.5.4
The table for TACACS+ server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TacacsPlusServerEntry

tacacsPlusServerEntry 7.1.20540.2.2.1.1.17.5.4.1
The conceptual row for tacacsPlusServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TacacsPlusServerEntry  

tacacsPlusServerIndex 7.1.20540.2.2.1.1.17.5.4.1.1
TACACS+ server index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

tacacsPlusServerAddress 7.1.20540.2.2.1.1.17.5.4.1.2
IP address of a TACACS+ server.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

tacacsPlusServerPortNumber 7.1.20540.2.2.1.1.17.5.4.1.3
TCP port number of a TACACS+ server.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

tacacsPlusServerKey 7.1.20540.2.2.1.1.17.5.4.1.4
The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..48)  

tacacsPlusServerStatus 7.1.20540.2.2.1.1.17.5.4.1.8
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

tacacsPlusServerRetransmit 7.1.20540.2.2.1.1.17.5.4.1.9
The maximum number of retransmissions for TACACS+.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..30  

tacacsPlusServerTimeout 7.1.20540.2.2.1.1.17.5.4.1.10
Timeout for TACACS+.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..540  

tacacsPlusServerGlobalRetransmit 7.1.20540.2.2.1.1.17.5.5
The maximum number of retransmissions for TACACS+ global server.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..30  

tacacsPlusServerGlobalTimeout 7.1.20540.2.2.1.1.17.5.6
Timeout for TACACS+ global server.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..540  

sshServerStatus 7.1.20540.2.2.1.1.17.6.1
The status of Secure Shell Server. Set this value to enabled(1) to enable SSH server, set this value to disabled(2) to disable the SSH server.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

sshServerMajorVersion 7.1.20540.2.2.1.1.17.6.2
The major version of the SSH Server.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sshServerMinorVersion 7.1.20540.2.2.1.1.17.6.3
The minor version of the SSH Server.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sshTimeout 7.1.20540.2.2.1.1.17.6.4
The time interval that the router waits for the SSH client to respond. The range is 1-120.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..120  

sshAuthRetries 7.1.20540.2.2.1.1.17.6.5
The number of attempts after which the interface is reset. The range is 1-5.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..5  

sshConnInfoTable 7.1.20540.2.2.1.1.17.6.6
The table for Secure Shell Connection.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SshConnInfoEntry

sshConnInfoEntry 7.1.20540.2.2.1.1.17.6.6.1
The conceptual row for sshConnInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SshConnInfoEntry  

sshConnID 7.1.20540.2.2.1.1.17.6.6.1.1
The connection ID of the Secure Shell Connection.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

sshConnMajorVersion 7.1.20540.2.2.1.1.17.6.6.1.2
The SSH major version.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sshConnMinorVersion 7.1.20540.2.2.1.1.17.6.6.1.3
The SSH minor version.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sshConnEncryptionType 7.1.20540.2.2.1.1.17.6.6.1.4
The encryption type of the SSH. none(1) means no encryption , des(2) means using DES encryption, tribeDes means using 3DES encryption.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), des(2), tribeDes(3)  

sshConnStatus 7.1.20540.2.2.1.1.17.6.6.1.5
The SSH connection State. negotiationStart(1) means the SSH is in its negotiation start state, authenticationStart(2) means the SSH is in authentication start state, sessionStart(3) means the SSH is in session start State.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER negotiationStart(1), authenticationStart(2), sessionStart(3)  

sshConnUserName 7.1.20540.2.2.1.1.17.6.6.1.6
The user name of the connection.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

sshDisconnect 7.1.20540.2.2.1.1.17.6.6.1.7
Set the variable to disconnect the connection, noDisconnect(1) will always be obtained when reading this variable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDisconnect(1), disconnect(2)  

sshConnEncryptionTypeStr 7.1.20540.2.2.1.1.17.6.6.1.8
The encryption type of the SSH.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

sshKeySize 7.1.20540.2.2.1.1.17.6.7
The SSH server key size.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 512..896  

sshRsaHostKey1 7.1.20540.2.2.1.1.17.6.8
The RSA host key segment 1.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey2 7.1.20540.2.2.1.1.17.6.9
The RSA host key segment 2.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey3 7.1.20540.2.2.1.1.17.6.10
The RSA host key segment 3.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey4 7.1.20540.2.2.1.1.17.6.11
The RSA host key segment 4.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey5 7.1.20540.2.2.1.1.17.6.12
The RSA host key segment 5.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey6 7.1.20540.2.2.1.1.17.6.13
The RSA host key segment 6.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey7 7.1.20540.2.2.1.1.17.6.14
The RSA host key segment 7.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshRsaHostKey8 7.1.20540.2.2.1.1.17.6.15
The RSA host key segment 8.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey1 7.1.20540.2.2.1.1.17.6.16
The DSA host key segment 1.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey2 7.1.20540.2.2.1.1.17.6.17
The DSA host key segment 2.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey3 7.1.20540.2.2.1.1.17.6.18
The DSA host key segment 3.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey4 7.1.20540.2.2.1.1.17.6.19
The DSA host key segment 4.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey5 7.1.20540.2.2.1.1.17.6.20
The DSA host key segment 5.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey6 7.1.20540.2.2.1.1.17.6.21
The DSA host key segment 6.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey7 7.1.20540.2.2.1.1.17.6.22
The DSA host key segment 7.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshDsaHostKey8 7.1.20540.2.2.1.1.17.6.23
The DSA host key segment 8.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshHostKeyGenAction 7.1.20540.2.2.1.1.17.6.24
This variable is for host key generating. For the set behavior: Set it to genRsaKey(2) to generate the RSA host key, and to genDsaKey(3) to generate the DSA host key, if genBothKeys(4) is set, both RSA and DSA host key are generated. For the get behavior: You will get genRsaKey(2), genDsaKey(3) or genBothKeys(4) when the key gen action is in progress. otherwise, you will get noGen(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noGen(1), genRsaKey(2), genDsaKey(3), genBothKeys(4)  

sshHostKeyGenStatus 7.1.20540.2.2.1.1.17.6.25
The result of the last KeyGen status. if no key gen action has been performed. you will get unknown(1) status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), success(2), failure(3)  

sshHostKeySaveAction 7.1.20540.2.2.1.1.17.6.26
To save host key from memory to flash. For the set behavior: Set it to save(2) to perform the save operation. For the get behavior: You will get save(1) when the save action is in progress. Otherwise, you will get noSave(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noSave(1), save(2)  

sshHostKeySaveStatus 7.1.20540.2.2.1.1.17.6.27
The result of the last savekey status. If no save action has been performed, you will get unknown(1) status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), success(2), failure(3)  

sshHostKeyDelAction 7.1.20540.2.2.1.1.17.6.28
To delete the host key. For the set behavior: Set it to delRsaKey(2) to delete the RSA host key, to delDsaKey(3) to delete the DSA host key, or to delBothKeys(4) to delete both RSA and DSA host key. For the get behavior: You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4) when the delete operation is in progress. Otherwise, you will get noDel(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDel(1), delRsaKey(2), delDsaKey(3), delBothKeys(4)  

sshUserTable 7.1.20540.2.2.1.1.17.6.29
The conceptual table of all of sshUserEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SshUserEntry

sshUserEntry 7.1.20540.2.2.1.1.17.6.29.1
The conceptual row for sshUserTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SshUserEntry  

sshUserName 7.1.20540.2.2.1.1.17.6.29.1.1
User Name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..8)  

sshUserRsaKey1 7.1.20540.2.2.1.1.17.6.29.1.2
The RSA user key segment 1.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey2 7.1.20540.2.2.1.1.17.6.29.1.3
The RSA user key segment 2.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey3 7.1.20540.2.2.1.1.17.6.29.1.4
The RSA user key segment 3.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey4 7.1.20540.2.2.1.1.17.6.29.1.5
The RSA user key segment 4.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey5 7.1.20540.2.2.1.1.17.6.29.1.6
The RSA user key segment 5.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey6 7.1.20540.2.2.1.1.17.6.29.1.7
The RSA user key segment 6.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey7 7.1.20540.2.2.1.1.17.6.29.1.8
The RSA user key segment 7.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserRsaKey8 7.1.20540.2.2.1.1.17.6.29.1.9
The RSA user key segment 8.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey1 7.1.20540.2.2.1.1.17.6.29.1.10
The DSA user key segment 1.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey2 7.1.20540.2.2.1.1.17.6.29.1.11
The DSA user key segment 2.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey3 7.1.20540.2.2.1.1.17.6.29.1.12
The DSA user key segment 3.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey4 7.1.20540.2.2.1.1.17.6.29.1.13
The DSA user key segment 4.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey5 7.1.20540.2.2.1.1.17.6.29.1.14
The DSA user key segment 5.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey6 7.1.20540.2.2.1.1.17.6.29.1.15
The DSA user key segment 6.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey7 7.1.20540.2.2.1.1.17.6.29.1.16
The DSA user key segment 7.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserDsaKey8 7.1.20540.2.2.1.1.17.6.29.1.17
The DSA user key segment 8.
Status: current Access: read-only
OBJECT-TYPE    
  KeySegment  

sshUserKeyDelAction 7.1.20540.2.2.1.1.17.6.29.1.18
To delete the user key. For the set behavior: Set it to delRsaKey(2) to delete the RSA user key, to delDsaKey(3) to delete the DSA user key, or to delBothKeys(4) to delete both RSA and DSA user key. For the get behavior: You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4) when the delete operation is in progress. Otherwise, you will get noDel(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDel(1), delRsaKey(2), delDsaKey(3), delBothKeys(4)  

sshRsaHostKeySHA1FingerPrint 7.1.20540.2.2.1.1.17.6.30
The SHA1 finger print of the RSA host key.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(65)  

sshRsaHostKeyMD5FingerPrint 7.1.20540.2.2.1.1.17.6.31
The MD5 finger print of RSA host key.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(47)  

sshDsaHostKeySHA1FingerPrint 7.1.20540.2.2.1.1.17.6.32
The SHA1 finger print of the DSA host key.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(65)  

sshDsaHostKeyMD5FingerPrint 7.1.20540.2.2.1.1.17.6.33
The MD5 finger print of the DSA host key.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(47)  

aaaMethodTable 7.1.20540.2.2.1.1.17.12.1
Contains the settings needed for accounting.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaMethodEntry

aaaMethodEntry 7.1.20540.2.2.1.1.17.12.1.1
A conceptual row in the aaaMethodTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaMethodEntry  

aaaMethodIndex 7.1.20540.2.2.1.1.17.12.1.1.1
Specifies the index for the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

aaaMethodName 7.1.20540.2.2.1.1.17.12.1.1.2
Name for the method.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..255)  

aaaMethodGroupName 7.1.20540.2.2.1.1.17.12.1.1.3
Name for the server to use, pointing to aaaRadiusGroupName or aaaTacacsPlusGroupName.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..255)  

aaaMethodMode 7.1.20540.2.2.1.1.17.12.1.1.4
startStop(1),sends a 'start' accounting notice at the beginning of a process and a 'stop' accounting notice at the end of a process. The 'start' accounting record is sent in the background. The requested user process begins regardless of whether or not the 'start' accounting notice was received by the accounting server.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER startStop(1)  

aaaMethodStatus 7.1.20540.2.2.1.1.17.12.1.1.5
Set to 1 to initiate the aaaMethodTable, 2 to destroy the table.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

aaaMethodClientType 7.1.20540.2.2.1.1.17.12.1.1.6
dot1x(1): Provides accounting service for 802.1x activity; exec(2): Provides accounting service for EXEC connection such as Telnet, SSH or console; commands(3): Provides accounting service for command privileges.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dot1x(1), exec(2), commands(3)  

aaaMethodPrivilegeLevel 7.1.20540.2.2.1.1.17.12.1.1.7
Specifies the privilege level for the entry. When aaaMethodClientType is in the mode of command(3), the privilege level is enabled to be accessed.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

aaaRadiusGroupTable 7.1.20540.2.2.1.1.17.12.2
Uses a subset of RADIUS servers for accounting as defined by the server group
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaRadiusGroupEntry

aaaRadiusGroupEntry 7.1.20540.2.2.1.1.17.12.2.1
A conceptual row of aaaRadiusGroupEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaRadiusGroupEntry  

aaaRadiusGroupIndex 7.1.20540.2.2.1.1.17.12.2.1.1
Specifies the index for the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

aaaRadiusGroupServerBitMap 7.1.20540.2.2.1.1.17.12.2.1.2
Identifies which RADIUS sever to use, each bit points to each radius server. 80 (1000 0000) point to radius server 1, C0 (11000000) points to radius 1 and radius 2.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1)  

aaaRadiusGroupName 7.1.20540.2.2.1.1.17.12.2.1.3
Uses a subset of servers for accounting as defined by the server group. The same name as aaaTacasPlusGroupName is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

aaaRadiusGroupStatus 7.1.20540.2.2.1.1.17.12.2.1.4
Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

aaaTacacsPlusGroupTable 7.1.20540.2.2.1.1.17.12.3
Uses a subset of TACACS+ servers for accounting as defined by the server group
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaTacacsPlusGroupEntry

aaaTacacsPlusGroupEntry 7.1.20540.2.2.1.1.17.12.3.1
A conceptual row of aaaTacacsPlusGroupEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaTacacsPlusGroupEntry  

aaaTacacsPlusGroupIndex 7.1.20540.2.2.1.1.17.12.3.1.1
Specifies the index for the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

aaaTacacsPlusGroupServerBitMap 7.1.20540.2.2.1.1.17.12.3.1.2
Identifies which TACACS+ sever to use.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1)  

aaaTacacsPlusGroupName 7.1.20540.2.2.1.1.17.12.3.1.3
Uses a subset of servers for accounting as defined by the server group. We can't have the same name as aaaRadiusGroupName
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

aaaTacacsPlusGroupStatus 7.1.20540.2.2.1.1.17.12.3.1.4
Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

aaaUpdate 7.1.20540.2.2.1.1.17.12.4
Specifies the periodic interim accounting records to be sent to the accounting server and periodic intervals to send accounting update records(in minutes).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2147483647  

aaaAccountTable 7.1.20540.2.2.1.1.17.12.5
Specifies an interface or a set of interfaces that the accounting method list will be applied to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaAccountEntry

aaaAccountEntry 7.1.20540.2.2.1.1.17.12.5.1
A conceptual row of aaaAccountTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaAccountEntry  

aaaAccountIfIndex 7.1.20540.2.2.1.1.17.12.5.1.1
Defined as the ifIndex
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

aaaAccountMethodName 7.1.20540.2.2.1.1.17.12.5.1.2
Specifies the name of the list of accounting methods to use. If no method name is specified, the system uses the default.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

aaaAccountProtocol 7.1.20540.2.2.1.1.17.12.5.1.3
Get the protocol type of a list method to know which server (RADIUS or TACACS+) is in use.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

aaaAccountStatus 7.1.20540.2.2.1.1.17.12.5.1.4
Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

aaaCommandPrivilegesTable 7.1.20540.2.2.1.1.17.12.8
Contains the settings needed for command privileges.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaCommandPrivilegesEntry

aaaCommandPrivilegesEntry 7.1.20540.2.2.1.1.17.12.8.1
A conceptual row in the aaaCommandPrivilegesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaCommandPrivilegesEntry  

aaaCommandPrivilegesLevel 7.1.20540.2.2.1.1.17.12.8.1.1
Specifies the privilege level index for the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..15  

aaaCommandPrivilegesInterfaceIndex 7.1.20540.2.2.1.1.17.12.8.1.2
Specifies the interface index for the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER console(1), vty(2)  

aaaCommandPrivilegesMethodName 7.1.20540.2.2.1.1.17.12.8.1.3
Specifies the method name in the lists under the mode of command privileges.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..255)  

aaaAccExecTable 7.1.20540.2.2.1.1.17.12.9
Specifies an interface or a set of interfaces that the accounting method list will be applied to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaAccExecEntry

aaaAccExecEntry 7.1.20540.2.2.1.1.17.12.9.1
A conceptual row of aaaAccExecTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaAccExecEntry  

aaaAccExecIndex 7.1.20540.2.2.1.1.17.12.9.1.1
The method of accessing CLI management.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER console(1), vty(2)  

aaaAccExecMethodName 7.1.20540.2.2.1.1.17.12.9.1.2
Specifies the name of the list of accounting methods to use. If no method name is specified, the system uses the default.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

ipFilterSnmpTable 7.1.20540.2.2.1.1.17.9.1
A list of IP address entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpFilterSnmpEntry

ipFilterSnmpEntry 7.1.20540.2.2.1.1.17.9.1.1
This entry includes an IP address range which the system will allow to connect to this device through SNMP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpFilterSnmpEntry  

ipFilterSnmpStartAddress 7.1.20540.2.2.1.1.17.9.1.1.1
The start IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

ipFilterSnmpEndAddress 7.1.20540.2.2.1.1.17.9.1.1.2
The end IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

ipFilterSnmpStatus 7.1.20540.2.2.1.1.17.9.1.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

ipFilterHTTPTable 7.1.20540.2.2.1.1.17.9.2
A list of IP address entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpFilterHTTPEntry

ipFilterHTTPEntry 7.1.20540.2.2.1.1.17.9.2.1
This entry includes an IP address range which the system will allow to connect to this device through SNMP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpFilterHTTPEntry  

ipFilterHTTPStartAddress 7.1.20540.2.2.1.1.17.9.2.1.1
The start IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

ipFilterHTTPEndAddress 7.1.20540.2.2.1.1.17.9.2.1.2
The end IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

ipFilterHTTPStatus 7.1.20540.2.2.1.1.17.9.2.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

ipFilterTelnetTable 7.1.20540.2.2.1.1.17.9.3
A list of IP address entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpFilterTelnetEntry

ipFilterTelnetEntry 7.1.20540.2.2.1.1.17.9.3.1
This entry includes an IP address range which the system will allow them to connect to this device through SNMP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpFilterTelnetEntry  

ipFilterTelnetStartAddress 7.1.20540.2.2.1.1.17.9.3.1.1
The start IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

ipFilterTelnetEndAddress 7.1.20540.2.2.1.1.17.9.3.1.2
The end IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

ipFilterTelnetStatus 7.1.20540.2.2.1.1.17.9.3.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

dot1xAuthConfigExtTable 7.1.20540.2.2.1.1.17.11.1
The extension table of dot1xAuthConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xAuthConfigExtEntry

dot1xAuthConfigExtEntry 7.1.20540.2.2.1.1.17.11.1.1
The entry of dot1xAuthConfigExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1xAuthConfigExtEntry  

dot1xAuthConfigExtOperMode 7.1.20540.2.2.1.1.17.11.1.1.1
The operation mode of dot1x port which allows host connection to 802.1x-authorized ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER singleHost(1), multiHost(2), macBasedAuth(3)  

dot1xAuthConfigExtMultiHostMaxCnt 7.1.20540.2.2.1.1.17.11.1.1.2
The maximum number of hosts when the dot1xAuthConfigExtOperMode is multiHost(2). When the operation Mode is singleHost(1), we can ignore this variables.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1024  

dot1xAuthConfigExtPortIntrusionAction 7.1.20540.2.2.1.1.17.11.1.1.3
Responses to intrusion when the authentication is failed; blockTraffic(1) means that to block traffic when the authentication is failed and guestVlan(2) means that to join to a guest VLAN when the authentication is failed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER blockTraffic(1), guestVlan(2)  

networkAccessPortTable 7.1.20540.2.2.1.1.17.13.2
A table contains the information of network access about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetworkAccessPortEntry

networkAccessPortEntry 7.1.20540.2.2.1.1.17.13.2.1
A conceptual row in the networkAccessPort table.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkAccessPortEntry  

networkAccessPortPortIndex 7.1.20540.2.2.1.1.17.13.2.1.1
The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this port index is the same interface identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

networkAccessPortMaxMacCount 7.1.20540.2.2.1.1.17.13.2.1.3
Specifies the maximum number of authenticated MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1024  

networkAccessPortMacFilter 7.1.20540.2.2.1.1.17.13.2.1.5
Specifies the MAC filter ID, Set this variable to zero to disable MAC filter.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..64  

networkAccessPortGuestVlan 7.1.20540.2.2.1.1.17.13.2.1.6
Specifies the guest VLAN ID. To disable the VLAN, set the value to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4094  

networkAccessPortLinkDetectionStatus 7.1.20540.2.2.1.1.17.13.2.1.7
Set this object to enabled(1) to enable link detection. Set this object to disabled(2) to disable link detection.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

networkAccessPortLinkDetectionMode 7.1.20540.2.2.1.1.17.13.2.1.8
Specifies the detection event for a port. Set this object to linkUp(1) to detect a link-up event. Set this object to linkDown(2) to detect a link-down event. Set this object to linkUpDown(3) to detect both link up and link down events.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER linkUp(1), linkDown(2), linkUpDown(3)  

networkAccessPortLinkDetectionAciton 7.1.20540.2.2.1.1.17.13.2.1.9
Specifies the action to take when a networkAccessPortLinkDetection event is triggered. Set this object to trap(1) to send a trap when a networkAccessPortLinkDetection event is triggered. Set this object to shutDown(2) to shut down the port when a networkAccessPortLinkDetection event is triggered. Set this object to trapAndShutDown(3) to send a trap and shut down the port when a networkAccessPortLinkDetection event is triggered.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trap(1), shutDown(2), trapAndShutDown(3)  

networkAccessPortDynamicQos 7.1.20540.2.2.1.1.17.13.2.1.10
Set this object to enabled(1) to enable Dynamic QoS. Set this object to disabled(2) to disable Dynamic QoS.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

networkAccessClearMacAddressMgt 7.1.20540.2.2.1.1.17.13.3
OBJECT IDENTIFIER    

networkAccessClearMacAddressAttribute 7.1.20540.2.2.1.1.17.13.3.1
Attribute for clearing Mac address. Specifies the certain attribute in Mac address table. all(1) indicates both reauthorized and learnt secure MAC address; static(2) indicates reauthorized MAC address; dynamic(3) indicates learnt secure MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), static(2), dynamic(3)  

networkAccessClearMacAddressMacAddress 7.1.20540.2.2.1.1.17.13.3.2
Specifies MAC address in the MAC address table for clearing MAC address. '000000' represents that no MAC address is specified.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

networkAccessClearMacAddressPort 7.1.20540.2.2.1.1.17.13.3.3
The specifies port in the MAC address table for clearing MAC address. '0' represents that no port is specified.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

networkAccessClearMacAddressAction 7.1.20540.2.2.1.1.17.13.3.4
Action for clearing MAC address . When setting this object to clear(2) to begin the clearing MAC address operation, a particular MAC address is cleared from the MAC address table. When the action is finshed whether or not it is successful or no action is taken, the value of this object is always noclear(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noclear(1), clear(2)  

networkAccessMacAddressTable 7.1.20540.2.2.1.1.17.13.4
Contains the information of network access MAC addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetworkAccessMacAddressEntry

networkAccessMacAddressEntry 7.1.20540.2.2.1.1.17.13.4.1
A conceptual row in the networkAccessMacAddress table.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkAccessMacAddressEntry  

networkAccessMacAddressAddress 7.1.20540.2.2.1.1.17.13.4.1.1
Specifies the authenticated MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

networkAccessMacAddressPort 7.1.20540.2.2.1.1.17.13.4.1.2
Specifies the port of authenticated MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

networkAccessMacAddressInetAddressType 7.1.20540.2.2.1.1.17.13.4.1.3
This object indicates the type of IP address denoted in networkAccessMacAddressRadiusServerInetAddress type.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

networkAccessMacAddressRadiusServerInetAddress 7.1.20540.2.2.1.1.17.13.4.1.4
Displays the IP address of radius server that authenticates the specified Mac address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

networkAccessMacAddressTime 7.1.20540.2.2.1.1.17.13.4.1.5
Displays the authentication time of the authenticated MAC address. The following form is a text string; 'yyyy MMm DDd HHh MMm SSs'. 'yyyy' is a four-digit year. 'MM' is a month. A single-digit month is preceded by a zero. 'DD' is the day of a month. A single-digit day is preceded by the value zero. 'HH', 'MM' and 'SS' are hour, minute, and second respectively. A single-digit hour, minute, and second are preceded by a zero value. An example is: '2001y 01m 01d 00h 04m 43s'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

networkAccessMacAddressAttribute 7.1.20540.2.2.1.1.17.13.4.1.6
Displays the attribute of an authenticated MAC address. static(1) indicates resauthorized secure MAC address. dynamic(2) indicates learnt secure MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

networkAccessAging 7.1.20540.2.2.1.1.17.13.5
Set this object to enabled(1) to enable MAC address aging feature. Set this object to disabled(2) to disable MAC address aging feature.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

networkAccessMacFilterWithMaskTable 7.1.20540.2.2.1.1.17.13.6
Contains the settings for MAC filter.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetworkAccessMacFilterWithMaskEntry

networkAccessMacFilterWithMaskEntry 7.1.20540.2.2.1.1.17.13.6.1
A conceptual row in the networkAccessMacFilterWithMaskTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkAccessMacFilterWithMaskEntry  

networkAccessMacFilterWithMaskID 7.1.20540.2.2.1.1.17.13.6.1.1
Specifies the MAC filter ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

networkAccessMacFilterWithMaskMacAddress 7.1.20540.2.2.1.1.17.13.6.1.2
Specifies the MAC address to be filtered.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

networkAccessMacFilterWithMaskMacAddressMask 7.1.20540.2.2.1.1.17.13.6.1.3
Specifies the MAC mask to be filtered.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

networkAccessMacFilterWithMaskStatus 7.1.20540.2.2.1.1.17.13.6.1.4
Set this object to valid(1) to create an entry. Set this object to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

macAuthReauthTime 7.1.20540.2.2.1.1.17.14.1
Specifies the reauthentication time period.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 120..1000000  

macAuthPortTable 7.1.20540.2.2.1.1.17.14.2
Contains the settings for mac authentication of each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacAuthPortEntry

macAuthPortEntry 7.1.20540.2.2.1.1.17.14.2.1
A conceptual row in the macAuthPort table.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAuthPortEntry  

macAuthPortIndex 7.1.20540.2.2.1.1.17.14.2.1.1
The port and the trunk (including trunk members) interface of the port table. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

macAuthPortMaxMacCount 7.1.20540.2.2.1.1.17.14.2.1.2
Specifies the maximum number of authenticated MAC addresses for MAC authentication.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1024  

macAuthPortIntrusionAction 7.1.20540.2.2.1.1.17.14.2.1.3
Responses to intrusion when the authentication is failed. blockTraffic(1) : denies network access to an unauthorized client; passTraffic(2) : allows unauthorized clients to the access network.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER blockTraffic(1), passTraffic(2)  

webAuthSystemAuthControl 7.1.20540.2.2.1.1.17.15.1
Sets enabled(1) to enable WebAuth feature and sets disabled(2) to disable WebAuth feature.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

webAuthSessionTimeout 7.1.20540.2.2.1.1.17.15.5
For authenticated success users, they can use internet service during a certain period. Whenever this period expires, users need to be re-authenticated again. This period is called session time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..3600  

webAuthQuietPeriod 7.1.20540.2.2.1.1.17.15.6
Specifies the re-authentication interval when the authentication fail attempts reach the webAuthLoginAttempts value. Unauthenticated user won't be authenticated during this period.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..180  

webAuthLoginAttempts 7.1.20540.2.2.1.1.17.15.7
Specifies the counter that configures the authentication fail times for a client. If authentication fail times reaches the specified value, the client are not allowed to login for some period.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

webAuthReauthenticateMgt 7.1.20540.2.2.1.1.17.15.8
OBJECT IDENTIFIER    

webAuthReauthenticatePort 7.1.20540.2.2.1.1.17.15.8.1
Specifies the port to re-authenticate for all of its authenticated hosts.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

webAuthReauthenticateInetAddressType 7.1.20540.2.2.1.1.17.15.8.2
Specifies host type to re-authenticate.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

webAuthReauthenticateInetAddress 7.1.20540.2.2.1.1.17.15.8.3
Specificies host to re-authenticate.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

webAuthReauthenticateAction 7.1.20540.2.2.1.1.17.15.8.4
Action for WebAuth re-authenication. When setting this object to reauth(2) to begin the re-authenticated operation, a particular user is re-authenticated. When the action is finshed whether it is successfully, or no action is taken, the value of this object is always noReauth(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReauth(1), reauth(2)  

webAuthPortConfigTable 7.1.20540.2.2.1.1.17.15.9
Contains the settings for web authentication of each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WebAuthPortConfigEntry

webAuthPortConfigEntry 7.1.20540.2.2.1.1.17.15.9.1
A conceptual row in the webAuthPortConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  WebAuthPortConfigEntry  

webAuthPortConfigPortIndex 7.1.20540.2.2.1.1.17.15.9.1.1
The port number of the port that may specify certain entry in the table which contains web authentication information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

webAuthPortConfigStatus 7.1.20540.2.2.1.1.17.15.9.1.2
Sets enabled(1) to enable web authentication feature for each port and sets disabled(2) to disable web authentication for each port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

webAuthPortConfigAuthenticatedHostCount 7.1.20540.2.2.1.1.17.15.9.1.3
Displays the authenticated host counts for each port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

webAuthPortInfoTable 7.1.20540.2.2.1.1.17.15.10
Contains the information for web authentication of each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WebAuthPortInfoEntry

webAuthPortInfoEntry 7.1.20540.2.2.1.1.17.15.10.1
A conceptual row in the webAuthPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  WebAuthPortInfoEntry  

webAuthPortInfoPortIndex 7.1.20540.2.2.1.1.17.15.10.1.1
The port number for which this entry contains web authentication information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

webAuthPortInfoPortAuthSuccessIndex 7.1.20540.2.2.1.1.17.15.10.1.2
The authentication success number of port for which this entry contains web authentication information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

webAuthPortInfoInetAddressType 7.1.20540.2.2.1.1.17.15.10.1.3
This object indicates the type of IP address denoted in webAuthPortInfoIpAddress type.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

webAuthPortInfoInetAddress 7.1.20540.2.2.1.1.17.15.10.1.4
The IP address which may specify the entry containing web authentication information.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

webAuthPortInfoRemainingSessiontime 7.1.20540.2.2.1.1.17.15.10.1.5
The remaining session time for authenticated hosts. During this period, they may use internet resource. When the session time expires, they will need to re-authenticate again.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

webAuthPortInfoStatus 7.1.20540.2.2.1.1.17.15.10.1.6
Displays the web authentication status for each port. authenticated (1) means the user is authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authenticated(1)  

sysLogStatus 7.1.20540.2.2.1.1.19.1
Whether the system log is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

sysLogHistoryFlashLevel 7.1.20540.2.2.1.1.19.2
Severity level for logging to flash.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

sysLogHistoryRamLevel 7.1.20540.2.2.1.1.19.3
Severity level for logging to RAM.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remoteLogMgt 7.1.20540.2.2.1.1.19.6
OBJECT IDENTIFIER    

remoteLogStatus 7.1.20540.2.2.1.1.19.6.1
Whether the remote log system is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteLogLevel 7.1.20540.2.2.1.1.19.6.2
Severity level for remote log.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remoteLogFacilityType 7.1.20540.2.2.1.1.19.6.3
The facility type for remote log.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER localUse0(16), localUse1(17), localUse2(18), localUse3(19), localUse4(20), localUse5(21), localUse6(22), localUse7(23)  

remoteLogServerTable 7.1.20540.2.2.1.1.19.6.4
A Table for storing the remote log Server list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteLogServerEntry

remoteLogServerEntry 7.1.20540.2.2.1.1.19.6.4.1
A conceptually row for remoteLogServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteLogServerEntry  

remoteLogServerIp 7.1.20540.2.2.1.1.19.6.4.1.1
The IP address of the remote log Server.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

remoteLogServerStatus 7.1.20540.2.2.1.1.19.6.4.1.2
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

smtpMgt 7.1.20540.2.2.1.1.19.7
OBJECT IDENTIFIER    

smtpStatus 7.1.20540.2.2.1.1.19.7.1
Set enabled(1) to enable the SMTP, set disabled(2) to disable the SMTP.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

smtpSeverityLevel 7.1.20540.2.2.1.1.19.7.2
Specify the SMTP minimum severity level to send the event message.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

smtpSourceEMail 7.1.20540.2.2.1.1.19.7.3
SMTP source email address, the sender's mail address that appears in the 'From' field of the mail.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..41)  

smtpServerIpTable 7.1.20540.2.2.1.1.19.7.4
The SMTP server IP table. The maximum servers to be added is 3.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SmtpServerIpEntry

smtpServerIpEntry 7.1.20540.2.2.1.1.19.7.4.1
A conceptual row of the smtpServerIpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SmtpServerIpEntry  

smtpServerIp 7.1.20540.2.2.1.1.19.7.4.1.1
SMTP mail server's IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

smtpServerIpStatus 7.1.20540.2.2.1.1.19.7.4.1.2
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

smtpDestEMailTable 7.1.20540.2.2.1.1.19.7.5
The table of the destination e-mail address. The maximum numbers of destination email address to be added is 5.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SmtpDestEMailEntry

smtpDestEMailEntry 7.1.20540.2.2.1.1.19.7.5.1
A conceptual row of the smtpDestEMailTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SmtpDestEMailEntry  

smtpDestEMail 7.1.20540.2.2.1.1.19.7.5.1.1
SMTP destination e-mail address.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..41)  

smtpDestEMailStatus 7.1.20540.2.2.1.1.19.7.5.1.2
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

consoleMgt 7.1.20540.2.2.1.1.20.1
OBJECT IDENTIFIER    

telnetMgt 7.1.20540.2.2.1.1.20.2
OBJECT IDENTIFIER    

consoleDataBits 7.1.20540.2.2.1.1.20.1.1
Number of data bits.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER databits7(1), databits8(2)  

consoleParity 7.1.20540.2.2.1.1.20.1.2
Defines the generation of a parity bit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER partyNone(1), partyEven(2), partyOdd(3)  

consoleStopBits 7.1.20540.2.2.1.1.20.1.4
The console stop bits, valid values are stopbits1(1) or stopbits2(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stopbits1(1), stopbits2(2)  

consoleExecTimeout 7.1.20540.2.2.1.1.20.1.5
In a serial console, use the consoleExecTimeout variable to set the interval that the EXEC command interpreter waits until user input is detected; set the value to 0 to disable it.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

consolePasswordThreshold 7.1.20540.2.2.1.1.20.1.6
The number of failed console logon attempts that may be made before the system will not accept a further attempt in the time specified by consoleSilentTime. A value of 0 disables the functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

consoleSilentTime 7.1.20540.2.2.1.1.20.1.7
The length of time that the management console is inaccessible after the number of failed logon attempts has reached consolePasswordThreshold. A value of 0 disables the functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

consoleAdminBaudRate 7.1.20540.2.2.1.1.20.1.8
Baud rate. Valid values are 2400, 4800, 9600, 19200, 38400, 57600, 115200. Setting this variable to 0 means autobaud. Please read the actual baud rate in the consoleOperBaudRate variable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

consoleOperBaudRate 7.1.20540.2.2.1.1.20.1.9
The baud rate currently in use.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

consoleLoginResponseTimeout 7.1.20540.2.2.1.1.20.1.10
Console login response timeout setting. Valid range is 0 to 300. Setting to 0 means disabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

telnetExecTimeout 7.1.20540.2.2.1.1.20.2.1
Specifies the interval that the system waits for user input before terminating the current telnet session.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

telnetPasswordThreshold 7.1.20540.2.2.1.1.20.2.2
The number of failed telnet logon attempts that may be made before the system will not accept a further attempt to logon with telnet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

telnetLoginResponseTimeout 7.1.20540.2.2.1.1.20.2.3
Telnet login response timeout setting. Valid range is 1 to 300. This timout setting cannot be disbled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..300  

telnetStatus 7.1.20540.2.2.1.1.20.2.4
To enable or disable the telnet function. Any new telnet request will be rejected and all current telnet sessions will be terminated if this status is set to disabled(2).
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

telnetPortNumber 7.1.20540.2.2.1.1.20.2.5
The telnet session port number.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sntpMgt 7.1.20540.2.2.1.1.23.1
OBJECT IDENTIFIER    

ntpMgt 7.1.20540.2.2.1.1.23.5
OBJECT IDENTIFIER    

sysSummerTimeMgt 7.1.20540.2.2.1.1.23.7
OBJECT IDENTIFIER    

sntpStatus 7.1.20540.2.2.1.1.23.1.1
Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

sntpServiceMode 7.1.20540.2.2.1.1.23.1.2
Service mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unicast(1)  

sntpPollInterval 7.1.20540.2.2.1.1.23.1.3
Polling interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..16384  

sntpServerTable 7.1.20540.2.2.1.1.23.1.4
Table for SNTP servers
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SntpServerEntry

sntpServerEntry 7.1.20540.2.2.1.1.23.1.4.1
Entry for SNTP servers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SntpServerEntry  

sntpServerIndex 7.1.20540.2.2.1.1.23.1.4.1.1
The index of a server. This table has fixed size.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..3  

sntpServerIpAddress 7.1.20540.2.2.1.1.23.1.4.1.2
The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index are 0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysCurrentTime 7.1.20540.2.2.1.1.23.2
This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the English name of the month. '_d' is the day of month. A single-digit day is preceded by a space. 'hh:mm:ss' is a 24-hour representations of hours, minutes, and seconds. A single-digit hour is preceded by a zero. 'yyyy' is a four-digit year. An example is: 'Jan 1 02:03:04 2002'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(20)  

sysTimeZone 7.1.20540.2.2.1.1.23.3
This is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a negative offset, this is '-'. 'hh:mm' in the hour and minute offset from UTC. A single-digit hour is preceded by a zero. When sysTimeZonePredefined object is set to any value other than none(1), this object will be empty string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(6)  

sysTimeZoneName 7.1.20540.2.2.1.1.23.4
The name of the time zone. When sysTimeZonePredefined object is set to any value other than none(1), this object will be empty string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..30)  

ntpStatus 7.1.20540.2.2.1.1.23.5.1
Set enabled(1) to enable the NTP, set disabled(2) to disable the NTP.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

ntpServiceMode 7.1.20540.2.2.1.1.23.5.2
Service mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unicast(1)  

ntpPollInterval 7.1.20540.2.2.1.1.23.5.3
Polling interval in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ntpAuthenticateStatus 7.1.20540.2.2.1.1.23.5.4
Set enabled(1) to enable the NTP Authenticate, set disabled(2) to disable the NTP.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

ntpServerTable 7.1.20540.2.2.1.1.23.5.5
Table for NTP servers
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NtpServerEntry

sysTimeZonePredefined 7.1.20540.2.2.1.1.23.6
Specifies the time zone predefined mode. If time zone is configured by sysTimeZone object, the value field will be none(1). When this variable is set to any value other than none(1), sysTimeZone and sysTimeZoneName will become empty strings. This object can be set to none(1) only when it is already equal to none(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), minus1200InternationalDateLineWest(8000), minus1100MidwayIslandSamoa(9000), minus1000Hawaii(10000), minus0930Taiohae(10300), minus0900Alaska(11000), minus0800PacificTimeTijuana(12000), minus0700Arizona(13000), minus0700ChihuahuaLaPazMazatlan(13001), minus0700MountainTimeUSCanada(13002), minus0600CentralAmerica(14000), minus0600CentralTimeUSCanada(14001), minus0600GuadalajaraMexicoCityMonterrey(14002), minus0600Saskatchewan(14003), minus0500BogotaLimaQuito(15000), minus0500EasternTimeUSCanada(15001), minus0500IndianaEast(15002), minus0400AtlanticTimeCanada(16000), minus0400CaracasLaPaz(16001), minus0400Santiago(16002), minus0330Newfoundland(16700), minus0300Brasilia(17000), minus0300BuenosAiresGeorgetown(17001), minus0300Greenland(17002), minus0200MidAtlantic(18000), minus0100Azores(19000), minus0100CapeVerdeIs(19001), gmtDublinEdinburghLisbonLondon(20000), gmtCasablancaMonrovia(20001), plus0100AmsterdamBerlinBernRomeStockholmVienna(21000), plus0100BelgradeBratislavaBudapestLjubljanaPrague(21001), plus0100BrusselsCopenhagenMadridParis(21002), plus0100SarajevoSkopjeWarsawZagreb(21003), plus0100WestCentralAfrica(21004), plus0200AthensBeirutIstanbulMinsk(22000), plus0200Bucharest(22001), plus0200Cairo(22002), plus0200HararePretoria(22003), plus0200HelsinkiKyivRigaSofiaTallinnVilnius(22004), plus0200Jerusalem(22005), plus0300Baghdad(23000), plus0300KuwaitRiyadh(23001), plus0300MoscowStPetersburgVolgograd(23002), plus0300Nairobi(23003), plus0330Tehran(23300), plus0400AbuDhabiMuscat(24000), plus0400BakuTbilisiYerevan(24001), plus0430Kabul(24300), plus0500Ekaterinburg(25000), plus0500IslamabadKarachiTashkent(25001), plus0530ChennaiCalcutaMumbaiNewDelhi(25300), plus0545Kathmandu(25450), plus0600AlmatyNovosibirsk(26000), plus0600AstanaDhaka(26001), plus0600SriJayawardenepura(26002), plus0630Rangoon(26300), plus0700BangkokHanoiJakarta(27000), plus0700Krasnoyarsk(27001), plus0800BeijingChongqingHongKongUrumqi(28000), plus0800IrkutskUlaanBataar(28001), plus0800KualaLumpurSingapore(28002), plus0800Perth(28003), plus0800Taipei(28004), plus0900OsakaSapporoTokyo(29000), plus0900Seoul(29001), plus0900Yakutsk(29002), plus0930Adelaide(29300), plus0930Darwin(29301), plus1000Brisbane(30000), plus1000CanberraMelbourneSydney(30001), plus1000GuamPortMoresby(30002), plus1000Hobart(30003), plus1000Vladivostok(30004), plus1030LordHoweIsland(30300), plus1100MagadanSolomonIsNewCaledonia(31000), plus1130Kingston(31300), plus1200AucklandWellington(32000), plus1200FijiKamchatkaMarshallIs(32001), plus1245ChathamIsland(32450), plus1300Nukualofa(33000), plus1400Kiritimati(34000)  

sysSummerTimeZoneName 7.1.20540.2.2.1.1.23.7.1
The name of the summer time zone. If sysSummerTimeMode is disabled, empty string will be shown.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..30)  

sysSummerTimeMode 7.1.20540.2.2.1.1.23.7.2
The mode of the summer time.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), recurring(2), date(3), predefined(4)  

sysSummerTimeRecurringTime 7.1.20540.2.2.1.1.23.7.3
This is a text string in the following form, based on Unix: 'www Ddd Mmm hh:mm - www Ddd Mmm hh:mm'. 'www' is the week number of the month. The range of 'www' is 1 to 5. The 5th week is the last week of the month. 'Ddd' are the first three letters of day of the week. 'Mmm' are the first three letters of the month. 'hh:mm' is a 24-hour representation of hours and minutes. A single-digit hour or minute is preceded by a zero. An example is: '1st Sun Jul 00:00 - 4th Sun Oct 00:00'. When sysSummerTimeMode is recurring(2), the object can be modified. Empty string will be shown when sysSummerTimeMode is not recurring(2).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(37)  

sysSummerTimeDateTime 7.1.20540.2.2.1.1.23.7.4
This is a text string in the following form, based on Unix: 'Mmm _d yyyy hh:mm - Mmm _d yyyy hh:mm'. 'Mmm' are the first three letters of the month. '_d' is the day of month. A single-digit day is preceded by a space. 'yyyy' is a four-digit year. The range is from 2001 to 2100. 'hh:mm' is a 24-hour representation of hours and minutes. A single-digit hour or minute is preceded by a zero. An example is: 'Jul 1 2002 00:00 - Oct 1 2002 00:00'. When sysSummerTimeMode is date(3), the object can be modified. Empty string will be shown when sysSummerTimeMode is not date(3).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(37)  

sysSummerTimePredefinedRegion 7.1.20540.2.2.1.1.23.7.5
The region of the summer time predefined mode. The offset of predefined mode is 60 minutes. When sysSummerTimeMode is predefined(4), the object can be modified. When sysSummerTimeMode is not predefined(4), none(1) will be shown. This object can be set to none(1) only when it is already equal to none(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), usa(2), europe(3), australia(4), newZealand(5)  

sysSummerTimeOffset 7.1.20540.2.2.1.1.23.7.6
Specifies the number of minutes to add during summer time. When sysSummerTimeMode is recurring(2) or date(3), offset time can be modified. Zero will be shown when sysSummerTimeMode is disabled(1). This object can only be set to zero when sysSummerTimeMode is disabled(1). This object can only be set to 60 when sysSummerTimeMode is predefined(4).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..99  

sysSummerTimeEffect 7.1.20540.2.2.1.1.23.7.7
This flag indicates whether summer time is in effect. A value of true(1) indicates summer time is in effect. A value of false(2) indicates summer time is not in effect.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ntpServerEntry 7.1.20540.2.2.1.1.23.5.5.1
Entry for NTP servers.
Status: current Access: not-accessible
OBJECT-TYPE    
  NtpServerEntry  

ntpServerIpAddress 7.1.20540.2.2.1.1.23.5.5.1.1
The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

ntpServerVersion 7.1.20540.2.2.1.1.23.5.5.1.2
NTP version.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..3  

ntpServerKeyId 7.1.20540.2.2.1.1.23.5.5.1.3
Key for a NTP server. This variable can only be written.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

ntpServerStatus 7.1.20540.2.2.1.1.23.5.5.1.4
The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'create', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER create(1), active(2), destroy(3)  

ntpAuthKeyTable 7.1.20540.2.2.1.1.23.5.6
Table for NTP Authentication keys
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NtpAuthKeyEntry

ntpAuthKeyEntry 7.1.20540.2.2.1.1.23.5.6.1
Entry for NTP Authentication keys.
Status: current Access: not-accessible
OBJECT-TYPE    
  NtpAuthKeyEntry  

ntpAuthKeyId 7.1.20540.2.2.1.1.23.5.6.1.1
The index of a Authentication key. This table has fixed size.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65536  

ntpAuthKeyWord 7.1.20540.2.2.1.1.23.5.6.1.2
The Authentication key word is used to created a key by the MD5 And the max length is 32.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

ntpAuthKeyStatus 7.1.20540.2.2.1.1.23.5.6.1.3
The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'create', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER create(1), active(2), destroy(3)  

fileCopyMgt 7.1.20540.2.2.1.1.24.1
OBJECT IDENTIFIER    

fileInfoMgt 7.1.20540.2.2.1.1.24.2
OBJECT IDENTIFIER    

fileAutoUpgradeMgt 7.1.20540.2.2.1.1.24.4
OBJECT IDENTIFIER    

fileCopySrcOperType 7.1.20540.2.2.1.1.24.1.1
The Copy Operation that we want to perform on the fileCopyDestOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOperType'. file(1) means we want to perform the 'copy file fileCopyDestType' operation, runningCfg(2) means we want to perform the 'copy running-config fileCopyDestOperType' operation, startUpCfg(3) means we want to perform the 'copy startup-config fileCopyDestOperType' operation, tftp(4) means we want to perform the 'copy tftp fileCopyDestOperType' operation, unit(5) is only available in stacking systems, in which we can copy files from one unit to another unit and it means we want to perform the 'copy unit fileCopyDestOperType' operation. http(6) means we can read the status of the transfer via HTTP protocol, but can not change the status. ftp(7) means we want to perform 'copy ftp fileCopyDestOperType' operation. The possible permutations are as follows: (1) copy file file; (2) copy file runningCfg; (3) copy file startUpCfg; (4) copy file tftp; (5) copy file unit (for stacking systems only); (6) copy runningCfg file; (7) copy runningCfg startUpCfg; (8) copy runningCfg tftp; (9) copy startupCfg file; (10) copy startupCfg runningCfg; (11)copy startupCfg tftp; (12) copy tftp file; (13) copy tftp runningCfg; (14) copy tftp startUpCfg; (15) copy unit file; (16) copy file ftp; (17) copy running-config ftp; (18) copy startup-config ftp; (19) copy ftp file; (20) copy ftp running-config; (21) copy ftp startup-config; (22) copy tftp cluster-member; (23) copy tftp oam-remote.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER file(1), runningCfg(2), startUpCfg(3), tftp(4), unit(5), http(6), ftp(7)  

fileCopySrcFileName 7.1.20540.2.2.1.1.24.1.2
The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has been specified. Note: If the fileCopySrcOperType is runningCfg(2) or startUpCfg(3), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

fileCopyDestOperType 7.1.20540.2.2.1.1.24.1.3
The Copy Operation that we want to perform on fileCopySrcOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOperType'. file(1) means we want to perform the 'copy fileCopySrcType file ' operation, runningCfg(2) means we want to perform the 'copy fileCopySrcOperType running-config ' operation, startUpCfg(3) means we want to perform the 'copy fileCopySrcOperType startup-config ' operation, tftp(4) means we want to perform the 'copy fileCopySrcOperType tftp' operation, unit(5) is only available in stacking systems in which we can copy files from one unit to another unit. It means we want to perform the 'copy fileCopySrcOperType unit' operation. http(6) means we can read the status of the transfer via HTTP protocol, but can not change the status. ftp(7) means we want to perform 'copy fileCopySrcOperType ftp' operation.oamRemote(9) means we want to perform 'copy fileCopySrcOperType oam-remote' operation, The possible permutations are as follows: (1) copy file file; (2) copy file runningCfg; (3) copy file startUpCfg; (4) copy file tftp; (5) copy file unit (for stacking system only); (6) copy runningCfg file; (7) copy runningCfg startUpCfg; (8) copy runningCfg tftp; (9) copy startupCfg file; (10) copy startupCfg runningCfg; (11) copy startupCfg tftp; (12) copy tftp file; (13) copy tftp runningCfg; (14) copy tftp startUpCfg; (15) copy unit file; (16) copy file ftp; (17) copy running-config ftp; (18) copy startup-config ftp; (19) copy ftp file; (20) copy ftp running-config; (21) copy ftp startup-config; (22) copy tftp cluster-member; (23) copy tftp oam-remote.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER file(1), runningCfg(2), startUpCfg(3), tftp(4), unit(5), http(6), ftp(7), oamRemote(9)  

fileCopyDestFileName 7.1.20540.2.2.1.1.24.1.4
The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has been specified. Note: If the fileCopyDestOperType is runningCfg(2), startupCfg(3), or oamRemote(9), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

fileCopyFileType 7.1.20540.2.2.1.1.24.1.5
Type of file to copy in fileCopyMgt. opcode(1) indicates operation code, config(2) indicates configuration file, bootRom(3) indicates diagnostic image file and loader(5) indicates loader image file. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this variable can be ignored. bootRom(3) and loader(5) can be set only when the fileCopySrcOperType is tftp(4) and fileCopyDestOperType is file(1). If the fileCopyDestOperType is oamRemote(9), this variable should be oamRemoteFirmware(4).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER opcode(1), config(2), bootRom(3), loader(5), oamRemoteFirmware(6)  

fileCopyTftpServer 7.1.20540.2.2.1.1.24.1.6
The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to '0.0.0.0' when no IP address has been specified. If neither fileCopySrcOperType nor fileCopyDestOperType is tftp(4), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

fileCopyUnitId 7.1.20540.2.2.1.1.24.1.7
Specifies the switch unit for stackable devices. When performing the 'copy unit file' or 'copy file unit' action, if neither fileCopySrcOperType nor fileCopyDestOperType is unit(5), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

fileCopyAction 7.1.20540.2.2.1.1.24.1.8
Setting this object to copy(2) to begin the copy operation. When the device is not copying, this object will have a value of notCopying(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notCopying(1), copy(2)  

fileCopyStatus 7.1.20540.2.2.1.1.24.1.9
The status of the last copy procedure, if any. This object will have a value of fileCopyUnknown(18) if no copy operation has been performed. If the fileCopyDestOperType is oamRemote(9), refer the detail results to fileCopyEfmOamResultTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31)  

fileCopyFtpLoginUsername 7.1.20540.2.2.1.1.24.1.12
Login username of the FTP server. If neither fileCopySrcOperType nor fileCopyDestOperType is ftp(7), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

fileCopyFtpLoginPassword 7.1.20540.2.2.1.1.24.1.13
Login password of the FTP server. If neither fileCopySrcOperType nor fileCopyDestOperType is ftp(7), this variable can be ignored. This variable can only be written. When this variable is read, it always returns a zero-length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

fileCopyOam 7.1.20540.2.2.1.1.24.1.15
OBJECT IDENTIFIER    

fileCopyOamPorts 7.1.20540.2.2.1.1.24.1.15.1
The port list which ports on the bitmap perform remote firmware upgrade. Note: If the fileCopyDestOperType is not oamRemote(9), this variable can be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

fileCopyOamResultTable 7.1.20540.2.2.1.1.24.1.15.2
Table for OAM remote firmware upgrade result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FileCopyOamResultEntry

fileCopyOamResultEntry 7.1.20540.2.2.1.1.24.1.15.2.1
A result entry for OAM remote firmware upgrade.
Status: current Access: not-accessible
OBJECT-TYPE    
  FileCopyOamResultEntry  

fileCopyOamLocalIfIndex 7.1.20540.2.2.1.1.24.1.15.2.1.1
The ifIndex value of the port excluding trunk. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

fileCopyOamResult 7.1.20540.2.2.1.1.24.1.15.2.1.2
The status of the last firmware upgrade procedure. This object will have a value of oamStatusUnknown(2) if no firmware upgrade operation has been performed. The oamSuccess(1) indicates that the remote firmware upgrade is success. The oamTransmissionTerminated(3) indicates that the transmission is terminated by local device. The oamTerminatedByPeer(4) indicates that the transmission is terminated by peer. The oamTimeout(5) indicates that the acknowledge or packets is not received from the peer. The oamResouceNotAvailable(6) indicates that the resource is not available to do firmware upgrade. The oamFileFormatNotSupported(7) indicates that the file format is not accepted by remote device. The oamChecksumError(8) indicates that the checksum is wrong. The oamWriteFlashError(9) indicates that it is failed to write the firmware to flash. The oamLinkDown(10) indicates that the OAM link is disconnected. The oamUpgradeFailed(11) indicates that the upgrade result is failed. The oamDownloadFailed(12) indicates that download firmware from TFTP server is failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oamSuccess(1), oamStatusUnknown(2), oamTransmissionTerminated(3), oamTerminatedByPeer(4), oamTimeout(5), oamResourceNotAvailable(6), oamFileFormatNotSupported(7), oamChecksumError(8), oamWriteFlashError(9), oamLinkDown(10), oamUpgradeFailed(11), oamDownloadFailed(12)  

fileInfoTable 7.1.20540.2.2.1.1.24.2.1
This table contain the information of the file system; we can also perform the delete, set startup file operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FileInfoEntry

fileInfoEntry 7.1.20540.2.2.1.1.24.2.1.1
A conceptually row for fileInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  FileInfoEntry  

fileInfoUnitID 7.1.20540.2.2.1.1.24.2.1.1.1
The switch unit in a stacking system, in a non-stacking system, this value is always 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

fileInfoFileName 7.1.20540.2.2.1.1.24.2.1.1.2
The file Name of the file System in the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

fileInfoFileType 7.1.20540.2.2.1.1.24.2.1.1.3
The file type of the file System in the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER diag(1), runtime(2), syslog(3), cmdlog(4), config(5), postlog(6), private(7), certificate(8), webarchive(9)  

fileInfoIsStartUp 7.1.20540.2.2.1.1.24.2.1.1.4
This flag indicate whether this file is a startup file. Set this object to true(1) to indicate that this is a startup file. Setting this object to false(2) is a invalid operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

fileInfoFileSize 7.1.20540.2.2.1.1.24.2.1.1.5
The sizes( in bytes) of the file.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

fileInfoCreationTime 7.1.20540.2.2.1.1.24.2.1.1.6
The creation time of the file, This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the English name of the month. '_d' is the day of month. A single-digit day is preceded by a space. 'hh:mm:ss' is a 24-hour representations of hours, minutes, and seconds. A single-digit hour is preceded by a zero. 'yyyy' is the four-digit year. An example is: 'Jan 1 02:03:04 2002'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(20)  

fileInfoDelete 7.1.20540.2.2.1.1.24.2.1.1.7
Write this object to delete(2) to delete a file, when read, this always return noDelete(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noDelete(1), delete(2)  

fileAutoDownloadResultTable 7.1.20540.2.2.1.1.24.3
This table contains file auto download result information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FileAutoDownloadResultEntry

fileAutoDownloadResultEntry 7.1.20540.2.2.1.1.24.3.1
A conceptual row for fileAutoDownloadResultTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  FileAutoDownloadResultEntry  

fileAutoDownloadResultUnitID 7.1.20540.2.2.1.1.24.3.1.1
The switch unit in a stacking system, in a non-stacking system, this value is always 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

fileAutoDownloadResultAction 7.1.20540.2.2.1.1.24.3.1.2
The status of the auto download action. value copying(2) will be obtained if the auto download action is currently processing, or value notCopying(1) will be obtained if no auto download action is currently processing. You can check the download result through the fileAutoDownloadResultStatus object after the download action has finished. Please note that this object is read-only, since the auto download action is triggered automatically by the system when an image file or a config file is set as startup setting through the fileInfoIsStartUp, restartOpCodeFile or restartConfigFile objects, but not set by the user manually through this fileAutoDownloadResultAction object.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notCopying(1), copying(2)  

fileAutoDownloadResultStatus 7.1.20540.2.2.1.1.24.3.1.3
The last auto download result status. value fileCopyUnknown(18) will be obtained if no download action has been performed before.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31)  

dnsDomainLookup 7.1.20540.2.2.1.1.26.1
To enable the IP Domain Naming System (DNS)-based host name-to-address translation.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dnsDomainName 7.1.20540.2.2.1.1.26.2
To define a default domain name to complete unqualified host names (names without a dotted-decimal domain name).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

dnsHostTable 7.1.20540.2.2.1.1.26.3
This table is used to define static host name-to-address mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DnsHostEntry

dnsHostEntry 7.1.20540.2.2.1.1.26.3.1
A conceptual row for the dnsHostTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DnsHostEntry  

dnsHostName 7.1.20540.2.2.1.1.26.3.1.1
The DNS Host name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..255)  

dnsHostIndex 7.1.20540.2.2.1.1.26.3.1.2
The secondary index of this dnsHostTable, representing the sequence of the dnsHostIp.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8  

dnsHostIp 7.1.20540.2.2.1.1.26.3.1.3
The DNS Host IP.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

dnsDomainListTable 7.1.20540.2.2.1.1.26.5
This table defines a list of default domain names to complete unqualified host names.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DnsDomainListEntry

dnsDomainListEntry 7.1.20540.2.2.1.1.26.5.1
A conceptual row for the dnsDomainListTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DnsDomainListEntry  

dnsDomainListName 7.1.20540.2.2.1.1.26.5.1.1
Domain name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..255)  

dnsDomainListStatus 7.1.20540.2.2.1.1.26.5.1.2
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

dnsNameServerTable 7.1.20540.2.2.1.1.26.6
To specify the address of one or more name servers to use for name and address resolution. This table has fixed size, will get 0.0.0.0 dnsNameServerIp if this entry does not exist.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DnsNameServerEntry

dnsNameServerEntry 7.1.20540.2.2.1.1.26.6.1
A conceptual row for dnsNameServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DnsNameServerEntry  

dnsNameServerIndex 7.1.20540.2.2.1.1.26.6.1.1
Index of this dnsNameServerTable, representing the sequence of the dnsNameServerIp.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

dnsNameServerIp 7.1.20540.2.2.1.1.26.6.1.2
IP address of name server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsCacheTable 7.1.20540.2.2.1.1.26.7
To display the RRs in DNS cache.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DnsCacheEntry

dnsCacheEntry 7.1.20540.2.2.1.1.26.7.1
A conceptual row for the dnsCacheTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DnsCacheEntry  

dnsCacheIndex 7.1.20540.2.2.1.1.26.7.1.1
The entry sequence number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

dnsCacheFlag 7.1.20540.2.2.1.1.26.7.1.2
Always get 4, means this record is unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dnsCacheType 7.1.20540.2.2.1.1.26.7.1.3
Cache Type: address(1); cname(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER address(1), cname(2)  

dnsCacheIp 7.1.20540.2.2.1.1.26.7.1.4
The DNS cache IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dnsCacheTtl 7.1.20540.2.2.1.1.26.7.1.5
The DNS cache TTL.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..876000  

dnsCacheDomain 7.1.20540.2.2.1.1.26.7.1.6
The DNS cache domain.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..255)  

fileAutoUpgradeOpCodeStatus 7.1.20540.2.2.1.1.24.4.1
Set this variable to enabled(1) to enable the device to automatically upgrade the current software image when a new version is detected. Set this variable to disabled(2) to disable this feature.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

fileAutoUpgradeOpCodePath 7.1.20540.2.2.1.1.24.4.2
The URL (Universal Resource Location) of the image file location for automatic upgrades. The URL schema can be set to TFTP or FTP. The Hostname is the IP address of the server. The last character of the URL is always a '/' and the filename must not be included in the URL.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

mcastStormMgt 7.1.20540.2.2.1.1.33.1
OBJECT IDENTIFIER    

mcastStormTable 7.1.20540.2.2.1.1.33.1.1
Table to manage the control of multicast storms for ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastStormEntry

mcastStormEntry 7.1.20540.2.2.1.1.33.1.1.1
The conceptual row of multiStormTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastStormEntry  

mcastStormIfIndex 7.1.20540.2.2.1.1.33.1.1.1.1
The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

mcastStormStatus 7.1.20540.2.2.1.1.33.1.1.1.2
Whether multicast storm protection is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

mcastStormPktRate 7.1.20540.2.2.1.1.33.1.1.1.4
Multicast storm threshold as packets per second. If this entry is for a trunk, this is the value for each member port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bcastStormMgt 7.1.20540.2.2.1.1.33.3
OBJECT IDENTIFIER    

bcastStormTable 7.1.20540.2.2.1.1.33.3.1
Table to manage the control of broadcast storms for ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BcastStormEntry

bcastStormEntry 7.1.20540.2.2.1.1.33.3.1.1
The conceptual row of bcastStormTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BcastStormEntry  

bcastStormIfIndex 7.1.20540.2.2.1.1.33.3.1.1.1
The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

bcastStormStatus 7.1.20540.2.2.1.1.33.3.1.1.2
Whether broadcast storm protection is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

bcastStormPktRate 7.1.20540.2.2.1.1.33.3.1.1.4
Broadcast storm threshold as packets per second. If this entry is for a trunk, this is the value for each member port. For a 10 Gbps port, the range is 1042 to 262143.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

unknownUcastStormMgt 7.1.20540.2.2.1.1.33.4
OBJECT IDENTIFIER    

unknownUcastStormTable 7.1.20540.2.2.1.1.33.4.1
Table to manage the unknown unicast storm control.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UnknownUcastStormEntry

unknownUcastStormEntry 7.1.20540.2.2.1.1.33.4.1.1
The conceptual row of unknownUcastStormTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UnknownUcastStormEntry  

unknownUcastStormIfIndex 7.1.20540.2.2.1.1.33.4.1.1.1
The port or trunk interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

unknownUcastStormStatus 7.1.20540.2.2.1.1.33.4.1.1.2
The parameter indicates that the unknown unicast storm protection is enabled/disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

unknownUcastStormSampleType 7.1.20540.2.2.1.1.33.4.1.1.3
The parameter indicates which storm protection mode is used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER packetRate(1)  

unknownUcastStormPktRate 7.1.20540.2.2.1.1.33.4.1.1.4
The parameter indicates the packet rate of the storm protection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mvrStatus 7.1.20540.2.2.1.1.44.1
Parameter to enable or disable MVR(Multicast VLAN Registration) on the device. NOTE: IGMP Snooping must be enabled first before enabling MVR and MVR will be disabled when IGMP Snooping is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

mvrVlanId 7.1.20540.2.2.1.1.44.2
To set VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mvrMaxGroups 7.1.20540.2.2.1.1.44.3
The maximum number of MVR groups.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mvrCurrentGroups 7.1.20540.2.2.1.1.44.4
The current number of MVR groups.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mvrGroupsCtl 7.1.20540.2.2.1.1.44.5
OBJECT IDENTIFIER    

mvrGroupsCtlId 7.1.20540.2.2.1.1.44.5.1
The start of a contiguous range of MVR group addresses.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mvrGroupsCtlCount 7.1.20540.2.2.1.1.44.5.2
The range count for configuring MVR group addresses.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

mvrGroupsCtlAction 7.1.20540.2.2.1.1.44.5.3
Sets the configure action for a contiguous range of MVR group addresses. The start addresses is the current value of mvrGroupsCtlId and the range count is the current value of mvrGroupsCtlCount. Set this object to create(2) to create MVR group addresses. Set this object to destory(3) to delete MVR group addresses. When the action is complete, this object becomes noAction(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(0), create(1), destory(2)  

mvrGroupTable 7.1.20540.2.2.1.1.44.6
The table for configuring the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrGroupEntry

mvrGroupEntry 7.1.20540.2.2.1.1.44.6.1
The entry for configuring the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrGroupEntry  

mvrGroupId 7.1.20540.2.2.1.1.44.6.1.1
The multicast address of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrGroutActive 7.1.20540.2.2.1.1.44.6.1.2
To indicate if the group has a member or not. If there are no members, the status is inactive(2); otherwise the status is active(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

mvrGroupStatus 7.1.20540.2.2.1.1.44.6.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

mvrGroupStaticTable 7.1.20540.2.2.1.1.44.7
The table for configuring the static members of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrGroupStaticEntry

mvrGroupStaticEntry 7.1.20540.2.2.1.1.44.7.1
The entry for configuring the static members of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrGroupStaticEntry  

mvrGroupStaticAddress 7.1.20540.2.2.1.1.44.7.1.1
The multicast address of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrGroupStaticPorts 7.1.20540.2.2.1.1.44.7.1.2
The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR group.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

mvrGroupStaticStatus 7.1.20540.2.2.1.1.44.7.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

mvrGroupCurrentTable 7.1.20540.2.2.1.1.44.8
The table for the current members of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrGroupCurrentEntry

mvrGroupCurrentEntry 7.1.20540.2.2.1.1.44.8.1
The entry for the current members of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrGroupCurrentEntry  

mvrGroupCurrentAddress 7.1.20540.2.2.1.1.44.8.1.1
The multicast address of the MVR group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrGroupCurrentPorts 7.1.20540.2.2.1.1.44.8.1.2
The complete set of ports currently associated with this MVR group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

mvrGroupCurrentReceiverVlan 7.1.20540.2.2.1.1.44.8.1.3
This object indicates the receiver VLAN of the MVR group. None of receiver VLAN belong to the MVR group when the value of this object is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

mvrPortTable 7.1.20540.2.2.1.1.44.9
The table for configuring the MVR port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrPortEntry

mvrPortEntry 7.1.20540.2.2.1.1.44.9.1
The entry for configuring the MVR port.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrPortEntry  

mvrIfIndex 7.1.20540.2.2.1.1.44.9.1.1
The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

mvrPortType 7.1.20540.2.2.1.1.44.9.1.2
For configuring the MVR port type. To disable the MVR port type, use the none(0).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), source(1), receiver(2)  

mvrPortImmediateLeave 7.1.20540.2.2.1.1.44.9.1.3
To enable immediate leave on MVR port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

mvrPortActive 7.1.20540.2.2.1.1.44.9.1.4
To indicate if the port is associated with the MVR group. If the port is the MVR receiver port or the MVR source port in MVR vlan, the status is active(1); otherwise the status is inactive(2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

mvrRunningStatus 7.1.20540.2.2.1.1.44.10
Describes the running status of MVR (Multicast VLAN Registration) to the switch. A value of true(1) indicates that all necessary conditions in the MVR environment are satisfied. A value of false(2) indicates that some necessary conditions in the MVR environment are not satisfied.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

mvrReceiverVlanId 7.1.20540.2.2.1.1.44.12
To set receiver VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. To disable the VLAN, set the value to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4094  

mvrMaxReceiverGroups 7.1.20540.2.2.1.1.44.13
The maximum number of MVR receiver groups.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mvrCurrentReceiverGroups 7.1.20540.2.2.1.1.44.14
The current number of MVR receiver groups.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mvrReceiverGroupTable 7.1.20540.2.2.1.1.44.15
The table for configuring the MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrReceiverGroupEntry

mvrReceiverGroupEntry 7.1.20540.2.2.1.1.44.15.1
The entry for configuring the MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrReceiverGroupEntry  

mvrReceiverGroupId 7.1.20540.2.2.1.1.44.15.1.1
The multicast address of a MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrReceiverGroupActive 7.1.20540.2.2.1.1.44.15.1.2
Indicate whether the receiver group has a member or not. If there are no members, the status will be inactive(2); if there are members, the status will be active(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

mvrReceiverGroupStatus 7.1.20540.2.2.1.1.44.15.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

mvrReceiverGroupStaticTable 7.1.20540.2.2.1.1.44.16
The table for configuring static members of the MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrReceiverGroupStaticEntry

mvrReceiverGroupStaticEntry 7.1.20540.2.2.1.1.44.16.1
The entry for configuring static members of the MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrReceiverGroupStaticEntry  

mvrReceiverGroupStaticAddress 7.1.20540.2.2.1.1.44.16.1.1
The multicast address of a MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrReceiverGroupStaticPorts 7.1.20540.2.2.1.1.44.16.1.2
The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR receiver group.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

mvrReceiverGroupStaticStatus 7.1.20540.2.2.1.1.44.16.1.3
Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

mvrReceiverGroupCurrentTable 7.1.20540.2.2.1.1.44.17
The table for the current members of a MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvrReceiverGroupCurrentEntry

mvrReceiverGroupCurrentEntry 7.1.20540.2.2.1.1.44.17.1
The entry for the current members of a MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvrReceiverGroupCurrentEntry  

mvrReceiverGroupCurrentAddress 7.1.20540.2.2.1.1.44.17.1.1
The multicast address of a MVR receiver group.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

mvrReceiverGroupCurrentPorts 7.1.20540.2.2.1.1.44.17.1.2
The complete set of ports currently associated with a MVR receiver group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

dhcpSnoopGlobal 7.1.20540.2.2.1.1.46.1
OBJECT IDENTIFIER    

dhcpSnoopVlan 7.1.20540.2.2.1.1.46.2
OBJECT IDENTIFIER    

dhcpSnoopInterface 7.1.20540.2.2.1.1.46.3
OBJECT IDENTIFIER    

dhcpSnoopBindings 7.1.20540.2.2.1.1.46.4
OBJECT IDENTIFIER    

dhcpSnoopStatistics 7.1.20540.2.2.1.1.46.5
OBJECT IDENTIFIER    

dhcpSnoopEnable 7.1.20540.2.2.1.1.46.1.1
This object indicates whether the DHCP Snooping feature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dhcpSnoopVerifyMacAddressEnable 7.1.20540.2.2.1.1.46.1.2
This object indicates whether DHCP Snooping Mac address verification is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dhcpSnoopInformationOptionEnable 7.1.20540.2.2.1.1.46.1.3
This object indicates whether the DHCP snooping information option(option 82) feature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dhcpSnoopInformationOptionPolicy 7.1.20540.2.2.1.1.46.1.4
This object indicates which reforwarding policy shall be used for DHCP snooping information option(option 82). A value of drop(1) means to drop the DHCP request packet which has the information option(option 82). A value of keep(2) means to keep the existing information option(option 82) of the DHCP request packet. A value of replace(3), which is the default value, means to replace the existing information option(option 82) of the DHCP request packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), keep(2), replace(3)  

dhcpSnoopBindingsTableCtlAction 7.1.20540.2.2.1.1.46.1.5
Set this to store(2) to store DHCP snooping binding entries to flash. Set this to clear(3) to clear DHCP snooping binding entries from flash. noAction(1) will always be obtained when reading this variable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAction(1), store(2), clear(3)  

dhcpSnoopVlanConfigTable 7.1.20540.2.2.1.1.46.2.1
A table contains DHCP Snooping configurations of existing VLANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopVlanConfigEntry

dhcpSnoopVlanConfigEntry 7.1.20540.2.2.1.1.46.2.1.1
An instance contains the configuration to enable or disable DHCP Snooping at each existing VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopVlanConfigEntry  

dhcpSnoopVlanIndex 7.1.20540.2.2.1.1.46.2.1.1.1
This object indicates the VLAN ID on which DHCP Snooping feature is configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

dhcpSnoopVlanEnable 7.1.20540.2.2.1.1.46.2.1.1.2
This object indicates whether DHCP Snooping is enabled in this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dhcpSnoopPortConfigTable 7.1.20540.2.2.1.1.46.3.1
A table provides the mechanism to configure the trust state of each port or trunk for DHCP Snooping purpose.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopPortConfigEntry

dhcpSnoopPortConfigEntry 7.1.20540.2.2.1.1.46.3.1.1
An instance contains the configuration to enable or disable trust state of each port or trunk for DHCP Snooping purpose.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopPortConfigEntry  

dhcpSnoopPortIfIndex 7.1.20540.2.2.1.1.46.3.1.1.1
The ifIndex value of the port or trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

dhcpSnoopPortTrustEnable 7.1.20540.2.2.1.1.46.3.1.1.2
This object indicates whether the port or trunk is trusted for DHCP Snooping purpose.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dhcpSnoopBindingsTable 7.1.20540.2.2.1.1.46.4.1
A table contains the DHCP bindings information learnt by the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopBindingsEntry

dhcpSnoopBindingsEntry 7.1.20540.2.2.1.1.46.4.1.1
An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopBindingsEntry  

dhcpSnoopBindingsVlanIndex 7.1.20540.2.2.1.1.46.4.1.1.1
This object indicates the VLAN which a DHCP client host belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

dhcpSnoopBindingsMacAddress 7.1.20540.2.2.1.1.46.4.1.1.2
This object indicates the MAC address of a DHCP client host.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dhcpSnoopBindingsAddrType 7.1.20540.2.2.1.1.46.4.1.1.3
This object indicates the type of IP address denoted in dhcpSnoopBindingsIpAddress type.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

dhcpSnoopBindingsEntryType 7.1.20540.2.2.1.1.46.4.1.1.4
This object indicates that this binding is obtained from dynamically learning or is a static configuraion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dynamic(1), static(2)  

dhcpSnoopBindingsIpAddress 7.1.20540.2.2.1.1.46.4.1.1.5
This object indicates the allocated IP address of a DHCP client host.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpSnoopBindingsPortIfIndex 7.1.20540.2.2.1.1.46.4.1.1.6
This object indicates the port or trunk where a DHCP client host connects to.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

dhcpSnoopBindingsLeaseTime 7.1.20540.2.2.1.1.46.4.1.1.7
This object indicates the leased time of this DHCP bindings.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dhcpSnoopTotalForwardedPkts 7.1.20540.2.2.1.1.46.5.1
Indicates the total number of packets subjected to DHCP Snooping is forwarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpSnoopUntrustedPortDroppedPkts 7.1.20540.2.2.1.1.46.5.3
Indicates the number of packets subjected to DHCP Snooping is dropped because they come from untrusted interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clusterEnable 7.1.20540.2.2.1.1.47.1
Enables or disables clustering on the device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

clusterCommanderEnable 7.1.20540.2.2.1.1.47.2
Enables or disables the device as commander in a cluster.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

clusterIpPool 7.1.20540.2.2.1.1.47.4
The start internal IP address of a cluster pool.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

clusterClearCandidateTable 7.1.20540.2.2.1.1.47.5
Setting this object to clear(2) starts to clear the candidate table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

clusterRole 7.1.20540.2.2.1.1.47.6
The current role of the device in a cluster. commander(1) : The switch is the controlling device in a cluster. candidate(2) : The switch has been discovered by the commander, but it has not been manually configured for access from the commander. activeMember(3): The switch has been manually configured for access from the commander and it is active in the cluster. disabled(5) : The switch has clustering disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER commander(1), candidate(2), activeMember(3), disabled(5)  

clusterMemberCount 7.1.20540.2.2.1.1.47.7
The total number of members in a cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clusterCandidateCount 7.1.20540.2.2.1.1.47.8
The total number of candidates in a cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

clusterCandidateTable 7.1.20540.2.2.1.1.47.9
A table listing cluster candidates.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClusterCandidateEntry

clusterCandidateEntry 7.1.20540.2.2.1.1.47.9.1
A conceptual row containing the information of the candidate.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClusterCandidateEntry  

clusterCandidateMacAddr 7.1.20540.2.2.1.1.47.9.1.1
The MAC address of the candidate.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

clusterCandidateDesc 7.1.20540.2.2.1.1.47.9.1.3
The description of the candidate.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..42)  

clusterCandidateRole 7.1.20540.2.2.1.1.47.9.1.4
The role of the candidate. candidate(2) : The switch is discovered by the commander, but it has not been manually configured for access from the commander. activeMember(3) : The switch is manually configured for access from the commander and it is active in the cluster. inactiveMember(4): The switch is manually configured for access from the commander, but it is inactive in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER candidate(2), activeMember(3), inactiveMember(4)  

clusterMemberTable 7.1.20540.2.2.1.1.47.10
A table listing clustering members.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClusterMemberEntry

clusterMemberEntry 7.1.20540.2.2.1.1.47.10.1
A conceptual row containing the information of the member.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClusterMemberEntry  

clusterMemberId 7.1.20540.2.2.1.1.47.10.1.1
The ID of the member.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

clusterMemberMacAddr 7.1.20540.2.2.1.1.47.10.1.2
The MAC address of the member.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

clusterMemberDesc 7.1.20540.2.2.1.1.47.10.1.3
The description of the member.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..42)  

clusterMemberActive 7.1.20540.2.2.1.1.47.10.1.4
The active status of the member. activeMember(3) : The switch is manually configured for access from the commander and it is active in the cluster. inactiveMember(4): The switch is manually configured for access from the commander, but it is inactive in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER activeMember(3), inactiveMember(4)  

clusterMemberAddCtl 7.1.20540.2.2.1.1.47.11
OBJECT IDENTIFIER    

clusterMemberAddCtlMacAddr 7.1.20540.2.2.1.1.47.11.1
The MAC address of the device associated with clusterMemberAddCtlAction.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

clusterMemberAddCtlId 7.1.20540.2.2.1.1.47.11.2
The member id associated with clusterMemberAddCtlAction.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clusterMemberAddCtlAction 7.1.20540.2.2.1.1.47.11.5
Adds the device to members that can be accessed from the commander. The MAC of the device is the current value of clusterMemberAddCtlMacAddr and the assigned member ID is the current value of clusterMemberAddCtlId. Set this object to add(2) to begin adding the member.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAdd(1), add(2)  

clusterMemberRemoveCtl 7.1.20540.2.2.1.1.47.12
OBJECT IDENTIFIER    

clusterMemberRemoveCtlId 7.1.20540.2.2.1.1.47.12.1
The member ID associated with clusterMemberRemoveCtlAction.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

clusterMemberRemoveCtlAction 7.1.20540.2.2.1.1.47.12.2
Removes the device from members that can be accessed from the commander. The member ID is the current value of clusterMemberRemoveCtlId. Set this object to remove(2) to begin removing the member.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noRemove(1), remove(2)  

ipSrcGuardConfigTable 7.1.20540.2.2.1.1.48.1
A table contains the configurations to enable or disable IP Source Guard at each port or trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpSrcGuardConfigEntry

ipSrcGuardConfigEntry 7.1.20540.2.2.1.1.48.1.1
An instance contains the configuration to enable or disable IP Source Guard at each port or trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpSrcGuardConfigEntry  

ipSrcGuardPortIfIndex 7.1.20540.2.2.1.1.48.1.1.1
This object idents the port or trunk which is capable of IP Source Guard feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ipSrcGuardMode 7.1.20540.2.2.1.1.48.1.1.2
This object indicates whether Ip Source Guard is enabled at this interface. If the value equals 0, it means Ip Source Guard is disabled. If the value equals 1, it means Ip Source Guard is enabled, and packets are filtered by checking source ip. If the value equals 2, it means Ip Source Guard is enabled and packets are filtered by checking source ip and source mac.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER diabled(0), srcIp(1), srcIpMac(2)  

ipSrcGuardAddrTable 7.1.20540.2.2.1.1.48.2
A table contains the IP Source Guard bindings information learnt by the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpSrcGuardAddrEntry

ipSrcGuardAddrEntry 7.1.20540.2.2.1.1.48.2.1
An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpSrcGuardAddrEntry  

ipSrcGuardBindingsVlanIndex 7.1.20540.2.2.1.1.48.2.1.1
This object indicates the VLAN which a DHCP client host belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

ipSrcGuardBindingsMacAddress 7.1.20540.2.2.1.1.48.2.1.2
This object indicates the MAC address of a DHCP client host.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

ipSrcGuardBindingsAddrType 7.1.20540.2.2.1.1.48.2.1.3
This object indicates the type of IP address denoted in ipSrcGuardBindingsIpAddress type.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

ipSrcGuardBindingsEntryType 7.1.20540.2.2.1.1.48.2.1.4
This object indicates that this binding is obtained from dynamically learning or is a static configuraion.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dynamic(1), static(3)  

ipSrcGuardBindingsIpAddress 7.1.20540.2.2.1.1.48.2.1.5
This object indicates the allocated IP address of a DHCP client host.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

ipSrcGuardBindingsPortIfIndex 7.1.20540.2.2.1.1.48.2.1.6
This object indicates the port or trunk where a DHCP client host connects to.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

ipSrcGuardBindingsLeaseTime 7.1.20540.2.2.1.1.48.2.1.7
This object indicates the leased time of this DHCP bindings.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ipSrcGuardBindingsStatus 7.1.20540.2.2.1.1.48.2.1.8
The status of this conceptual row entry. This object issued to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

upnpStatus 7.1.20540.2.2.1.1.49.1
Sets enabled(1) to enable UPnP device, and sets disabled(2) to disable UPnP device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

upnpAdvertisingDuration 7.1.20540.2.2.1.1.49.2
The interval(in seconds) between available UPnP device advertising messages sent by the switch.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..86400  

upnpTtl 7.1.20540.2.2.1.1.49.3
Specifies the TTL value of the UPnP advertising messages sent by the switch. When the TTL value is greater than 1, it is possible to send UPnP advertising messages to traverse multiple routers; at the same time, the UPnP device will send an IGMP Join message to the traverse multiple routers so that the routers will forward multicast messages to the UPnP device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sFlowStatus 7.1.20540.2.2.1.1.55.1
Set this to enabled(1) to enable global sFlow, and set this to disabled(2) to disable global sFlow.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

sFlowPortTable 7.1.20540.2.2.1.1.55.2
A table that contains the settings of sFlow.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SFlowPortEntry

sFlowPortEntry 7.1.20540.2.2.1.1.55.2.1
The conceptual row of sFlowPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SFlowPortEntry  

sFlowPortIndex 7.1.20540.2.2.1.1.55.2.1.1
The port number of a port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

sFlowPortStatus 7.1.20540.2.2.1.1.55.2.1.2
Set this to enabled(1) to enable sFlow on this port, and set this to disabled(2) to disable sFlow on this port.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

oamPortStatusTable 7.1.20540.2.2.1.1.52.1
A table contains the status of OAM at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamPortStatusEntry

oamPortStatusEntry 7.1.20540.2.2.1.1.52.1.1
An entry contains the status of OAM at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamPortStatusEntry  

oamPortIfIndex 7.1.20540.2.2.1.1.52.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

oamEnableStatus 7.1.20540.2.2.1.1.52.1.1.2
This object configures the status of OAM at each port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

oamPortModeTable 7.1.20540.2.2.1.1.52.2
A table contains the mode of OAM at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamPortModeEntry

oamPortModeEntry 7.1.20540.2.2.1.1.52.2.1
An entry contains the mode of OAM at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamPortModeEntry  

oamPortModeIndex 7.1.20540.2.2.1.1.52.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

oamPortMode 7.1.20540.2.2.1.1.52.2.1.2
This object configures the mode of OAM at each port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

oamPortClearStatTable 7.1.20540.2.2.1.1.52.3
A table contains the information of clear OAM statistics at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamPortClearStatEntry

oamPortClearStatEntry 7.1.20540.2.2.1.1.52.3.1
An entry contains the information of clear OAM statistics at each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamPortClearStatEntry  

oamPortClearStatIndex 7.1.20540.2.2.1.1.52.3.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

oamClearStatistics 7.1.20540.2.2.1.1.52.3.1.2
This variable is used to clear the counters for OAM. Set this variable to clear(2) to perform the clear operation, noClear(1) will always be displayed when reading this variable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noClear(1), clear(2)  

oamLoopbackTable 7.1.20540.2.2.1.1.52.4
Table for OAM remote loopback test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OamLoopbackEntry

oamLoopbackEntry 7.1.20540.2.2.1.1.52.4.1
Entry for OAM remote loopback test.
Status: current Access: not-accessible
OBJECT-TYPE    
  OamLoopbackEntry  

oamLoopbackTestIfIndex 7.1.20540.2.2.1.1.52.4.1.1
The ifIndex value of the port(excluding trunk). The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

oamLoopbackTestPacketNumber 7.1.20540.2.2.1.1.52.4.1.2
Setting the packet number when performing loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..99999999  

oamLoopbackTestPacketSize 7.1.20540.2.2.1.1.52.4.1.3
Setting the packet size when performing loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 64..1518  

oamLoopbackTestAction 7.1.20540.2.2.1.1.52.4.1.4
Setting this object to test(2) to begin the loopback test. This object will be noTest(1) when the loopback test is canceled or the loopback test has finished.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noTest(1), test(2)  

oamLoopbackTestResultTx 7.1.20540.2.2.1.1.52.4.1.5
A count of the the total number of loopback frames transmitted at last loopback test on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

oamLoopbackTestResultRx 7.1.20540.2.2.1.1.52.4.1.6
A count of the the total number of loopback frames received at last loopback test on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remoteAcceptableFrameTypeTable 7.1.20540.2.2.1.1.53.1
A table that contains the acceptable frame type configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteAcceptableFrameTypeEntry

remoteAcceptableFrameTypeEntry 7.1.20540.2.2.1.1.53.1.1
An entry that contains the acceptable frame type configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteAcceptableFrameTypeEntry  

remoteAcceptableFrameTypeIndex 7.1.20540.2.2.1.1.53.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteAcceptableFrameType 7.1.20540.2.2.1.1.53.1.1.2
This object configures the acceptable frame types at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER both(1), tagged(2), untagged(3)  

remoteEepromWriteTable 7.1.20540.2.2.1.1.53.2
A table contains the information of whether EEPROM is writable at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteEepromWriteEntry

remoteEepromWriteEntry 7.1.20540.2.2.1.1.53.2.1
An entry that contains the information of whether EEPROM is writable at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteEepromWriteEntry  

remoteEepromWriteIndex 7.1.20540.2.2.1.1.53.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteEepromWriteEnableStatus 7.1.20540.2.2.1.1.53.2.1.2
The object configures the status of EEPROM at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteFlowControlEnbaleTable 7.1.20540.2.2.1.1.53.3
A table contains the flow control configuation at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteFlowControlEnbaleEntry

remoteFlowControlEnbaleEntry 7.1.20540.2.2.1.1.53.3.1
An entry that contains the flow control configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteFlowControlEnbaleEntry  

remoteFLIndex 7.1.20540.2.2.1.1.53.3.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteFlowControlEnbale 7.1.20540.2.2.1.1.53.3.1.2
The object configures the status of flow control at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteNegotiationEnableTable 7.1.20540.2.2.1.1.53.4
A table contains the auto-negotiation configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteNegotiationEnableEntry

remoteNegotiationEnableEntry 7.1.20540.2.2.1.1.53.4.1
An entry contains the auto-negotiation configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteNegotiationEnableEntry  

remoteNegoIndex 7.1.20540.2.2.1.1.53.4.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteNegotiationEnable 7.1.20540.2.2.1.1.53.4.1.2
The object configures the status of auto negotiation at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteShutDownEnableTable 7.1.20540.2.2.1.1.53.5
A table contains the information of whether shutdown process is enabled at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteShutDownEnableEntry

remoteShutDownEnableEntry 7.1.20540.2.2.1.1.53.5.1
An entry contains the information of whether shutdown process is enabled at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteShutDownEnableEntry  

remoteSDIndex 7.1.20540.2.2.1.1.53.5.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteShutDownEnable 7.1.20540.2.2.1.1.53.5.1.2
Enable or disable the remote ShutDown.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteInputToSwitchTable 7.1.20540.2.2.1.1.53.6
A table contains the information of whether the input is tagged or untagged at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteInputToSwitchEntry

remoteInputToSwitchEntry 7.1.20540.2.2.1.1.53.6.1
An entry contains the information of whether the input is tagged or untagged at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteInputToSwitchEntry  

remoteInputIndex 7.1.20540.2.2.1.1.53.6.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteInputToSwitch 7.1.20540.2.2.1.1.53.6.1.2
The object configures the packet format of input at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tagged(1), untagged(2)  

remoteOutputToSubscriberTable 7.1.20540.2.2.1.1.53.7
A table contains the information of whether output to subscriber is tagged or untagged at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteOutputToSubscriberEntry

remoteOutputToSubscriberEntry 7.1.20540.2.2.1.1.53.7.1
An entry contains the information of whether output to subscriber is tagged or untagged at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteOutputToSubscriberEntry  

remoteOutputIndex 7.1.20540.2.2.1.1.53.7.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteOutputToSubscriber 7.1.20540.2.2.1.1.53.7.1.2
The object configures the packet format of output to subscriber at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tagged(1), untagged(2)  

remoteSpeedDuplexTable 7.1.20540.2.2.1.1.53.8
A table contains the speed-duplex configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteSpeedDuplexEntry

remoteSpeedDuplexEntry 7.1.20540.2.2.1.1.53.8.1
An entry contains the speed-duplex configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteSpeedDuplexEntry  

remoteSpeedDuplexIndex 7.1.20540.2.2.1.1.53.8.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteSpeedDuplex 7.1.20540.2.2.1.1.53.8.1.2
The object configures the speed-duplex at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER half10(1), full10(2), half100(3), full100(4), negotiation(5)  

remoteMdixTable 7.1.20540.2.2.1.1.53.9
A table contains the MDIX configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMdixEntry

remoteMdixEntry 7.1.20540.2.2.1.1.53.9.1
An entry contains the MDIX configuration at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMdixEntry  

remoteMdixIndex 7.1.20540.2.2.1.1.53.9.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteMdix 7.1.20540.2.2.1.1.53.9.1.2
The object configures the MDIX at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), normal(2), crossover(3)  

remoteDefaultTable 7.1.20540.2.2.1.1.53.10
A table contains the information of default VLAN and priority at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteDefaultEntry

remoteDefaultEntry 7.1.20540.2.2.1.1.53.10.1
An entry contains the information of default VLAN and priority at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteDefaultEntry  

remoteDefaultIndex 7.1.20540.2.2.1.1.53.10.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteDefaultVlan 7.1.20540.2.2.1.1.53.10.1.2
The object configures the default VLAN at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteDefaultPriority 7.1.20540.2.2.1.1.53.10.1.3
The object configures the default priority at the remote specified device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteDefaultEnable 7.1.20540.2.2.1.1.53.10.1.4
The object is to take effect default VLAN and priority at the remote specified device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteProtocolVlanTable 7.1.20540.2.2.1.1.53.11
A table contains the information of protocal VLAN at the remote specified device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteProtocolVlanEntry

remoteProtocolVlanEntry 7.1.20540.2.2.1.1.53.11.1
An entry contains the information of protocal VLAN at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteProtocolVlanEntry  

remoteProtocolVlanIndex 7.1.20540.2.2.1.1.53.11.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteProtocolVlanEtherType 7.1.20540.2.2.1.1.53.11.1.2
The object configures the Ether type at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteProtocolVlanVid 7.1.20540.2.2.1.1.53.11.1.3
The vlan of each port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteProtocolVlanPririty 7.1.20540.2.2.1.1.53.11.1.4
The object configures the VLAN ID at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteProtocolVlanRowStatus 7.1.20540.2.2.1.1.53.11.1.5
The status of this conceptual row entry. This object is issued to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but it is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but it is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station intending to create a new instance of a conceptual row and to have its status automatically set to be active and then to make it available for use by the managed device; - 'createAndWait', which is supplied by a management station intending to create a new instance of a conceptual row (but not to make it available for use by the managed device); and, - 'destroy', which is supplied by a management station intending to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' and 'active'. That is, when queried, an existing conceptual row has only three states: it is available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would be failed because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

remoteQueueCosMapTable 7.1.20540.2.2.1.1.53.12
A table contains the information of queue number and priority of CoS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteQueueCosMapEntry

remoteQueueCosMapEntry 7.1.20540.2.2.1.1.53.12.1
An entry contains the information of queue number and priority of CoS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteQueueCosMapEntry  

remoteQueueCosMapIndex 7.1.20540.2.2.1.1.53.12.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteQueueCosMapPriority 7.1.20540.2.2.1.1.53.12.1.2
The object configures the priority at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteQueueCosMapQueue 7.1.20540.2.2.1.1.53.12.1.3
The object configures the queue number of CoS map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteQueueCosMapEnable 7.1.20540.2.2.1.1.53.12.1.4
The object is to take effect the queue Cos map setting at the remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteQueueModeMgt 7.1.20540.2.2.1.1.53.13
OBJECT IDENTIFIER    

remoteQueueModeTable 7.1.20540.2.2.1.1.53.13.1
A table contains the information of queue mode at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteQueueModeEntry

remoteQueueModeEntry 7.1.20540.2.2.1.1.53.13.1.1
An entry contains the information of queue mode at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteQueueModeEntry  

remoteQueueModeIndex 7.1.20540.2.2.1.1.53.13.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteQueueMode 7.1.20540.2.2.1.1.53.13.1.1.2
The object configures the queue mode at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER wrr(1), strict(2)  

remoteWrrPortTable 7.1.20540.2.2.1.1.53.13.2
A table contains the information of the weighted round robin (WRR) at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteWrrPortEntry

remoteWrrPortEntry 7.1.20540.2.2.1.1.53.13.2.1
An entry contains the information of the WRR at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteWrrPortEntry  

remoteWrrPortIfIndex 7.1.20540.2.2.1.1.53.13.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteWrrPortQueueID 7.1.20540.2.2.1.1.53.13.2.1.2
The object configures the queue ID of WRR at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..3  

remoteWrrPortWeight 7.1.20540.2.2.1.1.53.13.2.1.3
The object configures the weight of WRR at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..15  

remoteMapTagPriorityMgt 7.1.20540.2.2.1.1.53.14
OBJECT IDENTIFIER    

remoteMapTagPriStatusTable 7.1.20540.2.2.1.1.53.14.1
A table contains the status of tag-priority map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTagPriStatusEntry

remoteMapTagPriStatusEntry 7.1.20540.2.2.1.1.53.14.1.1
An entry contains the status of tag-priority map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTagPriStatusEntry  

remoteMapTagPriStatusIndex 7.1.20540.2.2.1.1.53.14.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteMapTagPriStatus 7.1.20540.2.2.1.1.53.14.1.1.2
The object configures the status of tap-priority map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteMapTagPriorityTable 7.1.20540.2.2.1.1.53.14.2
A table contains the information of tag-priority map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTagPriorityEntry

remoteMapTagPriorityEntry 7.1.20540.2.2.1.1.53.14.2.1
An entry contains the information of tag-priority map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTagPriorityEntry  

remoteMapTagPriorityIndex 7.1.20540.2.2.1.1.53.14.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteMapTagPriority 7.1.20540.2.2.1.1.53.14.2.1.2
The object shows the tap-priority map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7  

remoteMapTagPriorityPri 7.1.20540.2.2.1.1.53.14.2.1.3
The object configures the priority of tap-priority map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remoteMapTosMgt 7.1.20540.2.2.1.1.53.15
OBJECT IDENTIFIER    

remoteMapTosStatusTable 7.1.20540.2.2.1.1.53.15.1
A table contains the status of ToS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTosStatusEntry

remoteMapTosStatusEntry 7.1.20540.2.2.1.1.53.15.1.1
An entry contains the status of ToS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTosStatusEntry  

remoteMapTosStatusIndex 7.1.20540.2.2.1.1.53.15.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteMapTosEnableStatus 7.1.20540.2.2.1.1.53.15.1.1.2
The object configures the status of ToS map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteMapTosTable 7.1.20540.2.2.1.1.53.15.2
A table contains the information of ToS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTosEntry

remoteMapTosEntry 7.1.20540.2.2.1.1.53.15.2.1
An entry contains the information of the TOS map at the remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTosEntry  

remoteMapTosIndex 7.1.20540.2.2.1.1.53.15.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteMapTos 7.1.20540.2.2.1.1.53.15.2.1.2
The object shows the ToS map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

remoteMapTosPri 7.1.20540.2.2.1.1.53.15.2.1.3
The object configures the the priority of ToS map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remoteMapTosStatus 7.1.20540.2.2.1.1.53.15.2.1.4
The status of this conceptual row entry. This object is isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but it is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but it is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station intending to create a new instance of a conceptual row and to have its status automatically set to be active, and then to make it available for use by the managed device; - 'createAndWait', which is supplied by a management station intending to create a new instance of a conceptual row (but not to make it available for use by the managed device); and, - 'destroy', which is supplied by a management station intending to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' and 'active'. That is, when queried, an existing conceptual row has only three states: it is available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would be failed because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

remoteMapTrafficClassMgt 7.1.20540.2.2.1.1.53.16
OBJECT IDENTIFIER    

remoteMapTrafficClassStatusTable 7.1.20540.2.2.1.1.53.16.1
A table contains the status of traffic class map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTrafficClassStatusEntry

remoteMapTrafficClassStatusEntry 7.1.20540.2.2.1.1.53.16.1.1
An entry contains the status of traffic class map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTrafficClassStatusEntry  

remoteMapTCStatusIndex 7.1.20540.2.2.1.1.53.16.1.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteMapTCEnableStatus 7.1.20540.2.2.1.1.53.16.1.1.2
The object configures the status of traffic class map at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteMapTrafficClassTable 7.1.20540.2.2.1.1.53.16.2
A table contains the information of traffic class map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMapTrafficClassEntry

remoteMapTrafficClassEntry 7.1.20540.2.2.1.1.53.16.2.1
An entry contains the information of traffic class map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMapTrafficClassEntry  

remoteMapTrafficClassIfIndex 7.1.20540.2.2.1.1.53.16.2.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteMapTrafficClass 7.1.20540.2.2.1.1.53.16.2.1.2
The object shows the traffic class map at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

remoteMapCos 7.1.20540.2.2.1.1.53.16.2.1.3
The object configures the value of CoS at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remoteMapTrafficClassStatus 7.1.20540.2.2.1.1.53.16.2.1.4
The status of this conceptual row entry. This object is issued to manage the creation and deletion of conceptual rows. For the following, check the corrections above. - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

remoteFactoryDefaultTable 7.1.20540.2.2.1.1.53.17
A table contains the factory default setting at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteFactoryDefaultEntry

remoteFactoryDefaultEntry 7.1.20540.2.2.1.1.53.17.1
An entry contains the factory default setting at the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteFactoryDefaultEntry  

remoteFactoryDefaultIndex 7.1.20540.2.2.1.1.53.17.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteFactoryDefault 7.1.20540.2.2.1.1.53.17.1.2
This object is to apply the factory default setting at the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER set(1)  

remoteDeviceStatisticTable 7.1.20540.2.2.1.1.53.18
A table shows the statistics for each remote device's port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteDeviceStatisticEntry

remoteDeviceStatisticEntry 7.1.20540.2.2.1.1.53.18.1
An entry shows the statistics for each remote device's port.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteDeviceStatisticEntry  

remoteStatisticPortIndex 7.1.20540.2.2.1.1.53.18.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteDeviceStatisticIfIndex 7.1.20540.2.2.1.1.53.18.1.2
This object shows the ifIndex value of the remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteTxPausePacket 7.1.20540.2.2.1.1.53.18.1.3
The total number of pause frames transmitted from the remote device's port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remoteRxPausePacket 7.1.20540.2.2.1.1.53.18.1.4
The total number of pause frames received from the remote device's port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remoteRxErrorPacket 7.1.20540.2.2.1.1.53.18.1.5
The total number of error frames received from the remote device's port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remoteQueuePacketStatisticTable 7.1.20540.2.2.1.1.53.19
A table contains the packet statistics of each queue for the remote device's port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteQueuePacketStatisticEntry

remoteQueuePacketStatisticEntry 7.1.20540.2.2.1.1.53.19.1
An entry contains the packet statistics of each queue for the remote device's port.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteQueuePacketStatisticEntry  

remoteQueuePacketStatisticPortIndex 7.1.20540.2.2.1.1.53.19.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteQueuePacketDeviceStatisticIfIndex 7.1.20540.2.2.1.1.53.19.1.2
This object shows the ifIndex value of the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteQueuePacketQueueIndex 7.1.20540.2.2.1.1.53.19.1.3
This object shows the index of packet queue of the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

remoteQueueDropPacket 7.1.20540.2.2.1.1.53.19.1.4
The total number of packets dropped by the remote device's port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remoteQueueForwardingPacket 7.1.20540.2.2.1.1.53.19.1.5
The total number of packets forwarded by the remote device's port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

remoteMacAddressTable 7.1.20540.2.2.1.1.53.20
A table contains the MAC address of the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteMacAddressEntry

remoteMacAddressEntry 7.1.20540.2.2.1.1.53.20.1
An entry contains the MAC address of the specified remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteMacAddressEntry  

remoteMacAddressIfIndex 7.1.20540.2.2.1.1.53.20.1.1
This object shows the ifIndex value of the port excluding trunk.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteMacAddress 7.1.20540.2.2.1.1.53.20.1.2
This object shows the MAC address of the specified remote device.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

remoteMacAddressStatus 7.1.20540.2.2.1.1.53.20.1.3
This object shows the information of whether the MAC address of the remote device is valided.
Status: current Access: read-write
OBJECT-TYPE    
  ValidStatus  

remoteDeviceMgt 7.1.20540.2.2.1.1.53.21
OBJECT IDENTIFIER    

remoteDeviceReset 7.1.20540.2.2.1.1.53.21.1
To reset the remote device which is connected to a port, assign remoteDeviceReset to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteDeviceFactoryDefault 7.1.20540.2.2.1.1.53.21.2
To reset the remote device which is connected to a port and restore the default setting, assign remoteDeviceFactoryDefault to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

remoteAccessPointTable 7.1.20540.2.2.1.1.53.21.3
Contains the access point setting of CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteAccessPointEntry

remoteAccessPointEntry 7.1.20540.2.2.1.1.53.21.3.1
A conceptual row in the remoteAccessPoint table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteAccessPointEntry  

remoteAccessPointLocalPort 7.1.20540.2.2.1.1.53.21.3.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteAccessPointStatus 7.1.20540.2.2.1.1.53.21.3.1.2
Set this to enabled(1) to enable the Wireless Access Point function. Sets disabled(2) to disable the Wireless Access Point function.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteDhcpServerTable 7.1.20540.2.2.1.1.53.21.4
Contains the DHCP server setting of CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteDhcpServerEntry

remoteDhcpServerEntry 7.1.20540.2.2.1.1.53.21.4.1
A conceptual row in the remoteDhcpServer table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteDhcpServerEntry  

remoteDhcpServerLocalPort 7.1.20540.2.2.1.1.53.21.4.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteDhcpServerStatus 7.1.20540.2.2.1.1.53.21.4.1.2
If this is enabled(1), the remote device acts as a DHCP server on the LAN side. If this is disabled(2), the remote device does not act as a DHCP server.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remoteDhcpServerIpAddress 7.1.20540.2.2.1.1.53.21.4.1.3
The IP address of DHCP server at remote device.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

remoteDhcpServerSubnetMask 7.1.20540.2.2.1.1.53.21.4.1.4
The subnet mask of DHCP server at remote device.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

remoteDhcpServerGateway 7.1.20540.2.2.1.1.53.21.4.1.5
The IP Address of the default gateway at remote device. If this value is undefined or unknown, it shall have the value 0.0.0.0.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

remoteVlanTable 7.1.20540.2.2.1.1.53.21.5
Contains the VLAN settings of CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteVlanEntry

remoteVlanEntry 7.1.20540.2.2.1.1.53.21.5.1
A conceptual row in the remoteVlan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteVlanEntry  

remoteVlanLocalPort 7.1.20540.2.2.1.1.53.21.5.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remoteVlanId 7.1.20540.2.2.1.1.53.21.5.1.2
Specifiies the VLAN ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

remoteVlanStatus 7.1.20540.2.2.1.1.53.21.5.1.3
Set valid(1) to create the VLAN. Set invalid(2) to delete the VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

remotePortMgt 7.1.20540.2.2.1.1.53.22
OBJECT IDENTIFIER    

remotePortAdminTable 7.1.20540.2.2.1.1.53.22.1
Contains the admin status of LAN ports on CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemotePortAdminEntry

remotePortAdminEntry 7.1.20540.2.2.1.1.53.22.1.1
A conceptual row in the remotePortAdmin table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemotePortAdminEntry  

remotePortAdminLocalPort 7.1.20540.2.2.1.1.53.22.1.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remotePortAdminRemotePort 7.1.20540.2.2.1.1.53.22.1.1.2
The port interface of remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

remotePortAdminStatus 7.1.20540.2.2.1.1.53.22.1.1.3
If this is enabled(1), the remote port is in enabled. If this is disabled(2), the remote port is not in enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remotePortPvidTable 7.1.20540.2.2.1.1.53.22.2
Contains the VID of LAN ports on CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemotePortPvidEntry

remotePortPvidEntry 7.1.20540.2.2.1.1.53.22.2.1
A conceptual row in the remotePortPvid table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemotePortPvidEntry  

remotePortPvidLocalPort 7.1.20540.2.2.1.1.53.22.2.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remotePortPvidRemotePort 7.1.20540.2.2.1.1.53.22.2.1.2
The port interface of remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

remotePortPvid 7.1.20540.2.2.1.1.53.22.2.1.3
Sets default VLAN on remote port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

remotePortPriorityTable 7.1.20540.2.2.1.1.53.22.3
Contains the priority of LAN ports on CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemotePortPriorityEntry

remotePortPriorityEntry 7.1.20540.2.2.1.1.53.22.3.1
A conceptual row in the remotePortPriority table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemotePortPriorityEntry  

remotePortPriorityLocalPort 7.1.20540.2.2.1.1.53.22.3.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remotePortPriorityRemotePort 7.1.20540.2.2.1.1.53.22.3.1.2
The port interface of remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

remotePortPriority 7.1.20540.2.2.1.1.53.22.3.1.3
Sets default priority on remote port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

remotePortIgmpSnoopingTable 7.1.20540.2.2.1.1.53.22.4
Contains the IGMP snooping status of LAN ports on CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemotePortIgmpSnoopingEntry

remotePortIgmpSnoopingEntry 7.1.20540.2.2.1.1.53.22.4.1
A conceptual row in the remotePortIgmpSnooping table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemotePortIgmpSnoopingEntry  

remotePortIgmpSnoopingLocalPort 7.1.20540.2.2.1.1.53.22.4.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remotePortIgmpSnoopingRemotePort 7.1.20540.2.2.1.1.53.22.4.1.2
The port interface of remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

remotePortIgmpSnooping 7.1.20540.2.2.1.1.53.22.4.1.3
If this is enabled(1), IGMP snooping is enabled on the remote port. If this is disabled(2), IGMP snooping is disabled on the remote port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

remotePortCountersTable 7.1.20540.2.2.1.1.53.22.5
Contains the information of LAN ports on CPE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemotePortCountersEntry

remotePortCountersEntry 7.1.20540.2.2.1.1.53.22.5.1
A conceptual row in the remotePortCounters table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemotePortCountersEntry  

remotePortCountersLocalPort 7.1.20540.2.2.1.1.53.22.5.1.1
The port interface on the switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

remotePortCountersRemotePort 7.1.20540.2.2.1.1.53.22.5.1.2
The port interface of remote device.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

remotePortCountersInUnicastSupported 7.1.20540.2.2.1.1.53.22.5.1.3
A value of true(1) indicates that supports receiving unicast packet counts. A value of false(2) indicates that not support receiving unicast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInUnicast 7.1.20540.2.2.1.1.53.22.5.1.4
The total number of unicast packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInBroadcastSupported 7.1.20540.2.2.1.1.53.22.5.1.5
A value of true(1) indicates that supports receiving broadcast packet counts. A value of false(2) indicates that not support receiving broadcast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInBroadcast 7.1.20540.2.2.1.1.53.22.5.1.6
The total number of broadcasts packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInPauseSupported 7.1.20540.2.2.1.1.53.22.5.1.7
A value of true(1) indicates that supports receiving pause packet counts. A value of false(2) indicates that not support receiving pause packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInPause 7.1.20540.2.2.1.1.53.22.5.1.8
The total number of pause packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInMulticastSupported 7.1.20540.2.2.1.1.53.22.5.1.9
A value of true(1) indicates that supports receiving multicast packet counts. A value of false(2) indicates that not support receiving multicast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInMulticast 7.1.20540.2.2.1.1.53.22.5.1.10
The total number of multicasts packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersOutUnicastSupported 7.1.20540.2.2.1.1.53.22.5.1.11
A value of true(1) indicates that supports transmitting unicast packet counts. A value of false(2) indicates that not support transmitting unicast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersOutUnicast 7.1.20540.2.2.1.1.53.22.5.1.12
The total number of unicast packets transmitted from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersOutBroadcastSupported 7.1.20540.2.2.1.1.53.22.5.1.13
A value of true(1) indicates that supports transmitting broadcast packet counts. A value of false(2) indicates that not support transmitting broadcast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersOutBroadcast 7.1.20540.2.2.1.1.53.22.5.1.14
The total number of broadcast packets transmitted from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersOutMulticastSupported 7.1.20540.2.2.1.1.53.22.5.1.15
A value of true(1) indicates that supports transmitting multicast packet counts. A value of false(2) indicates that not support transmitting multicast packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersOutMulticast 7.1.20540.2.2.1.1.53.22.5.1.16
The total number of multicast packets transmitted from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInFcsErrorsSupported 7.1.20540.2.2.1.1.53.22.5.1.17
A value of true(1) indicates that supports receiving FCS error packet counts. A value of false(2) indicates that not support receiving FCS error packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInFcsErrors 7.1.20540.2.2.1.1.53.22.5.1.18
The total number of FCS error packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersOutFcsErrorsSupported 7.1.20540.2.2.1.1.53.22.5.1.19
A value of true(1) indicates that supports transmitting FCS error packet counts. A value of false(2) indicates that not support transmitting FCS error packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersOutFcsErrors 7.1.20540.2.2.1.1.53.22.5.1.20
The total number of FCS error packets transmitted from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInGoodOctetsSupported 7.1.20540.2.2.1.1.53.22.5.1.21
A value of true(1) indicates that supports receiving normal packet counts. A value of false(2) indicates that not support receiving normal packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInGoodOctets 7.1.20540.2.2.1.1.53.22.5.1.22
The total number of normal packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersOutGoodOctetsSupported 7.1.20540.2.2.1.1.53.22.5.1.23
A value of true(1) indicates that supports transmitting normal packet counts. A value of false(2) indicates that not support transmitting normal packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersOutGoodOctets 7.1.20540.2.2.1.1.53.22.5.1.24
The total number of normal packets transmitted from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInBadOctetsSupported 7.1.20540.2.2.1.1.53.22.5.1.25
A value of true(1) indicates that supports receiving bad packet counts. A value of false(2) indicates that not support receiving bad packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInBadOctets 7.1.20540.2.2.1.1.53.22.5.1.26
The total number of bad packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersInDiscardsSupported 7.1.20540.2.2.1.1.53.22.5.1.27
A value of true(1) indicates that supports receiving discard packet counts. A value of false(2) indicates that not support receiving discard packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersInDiscards 7.1.20540.2.2.1.1.53.22.5.1.28
The total number of discard packets received from remote port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersAlignmentErrorsSupported 7.1.20540.2.2.1.1.53.22.5.1.29
A value of true(1) indicates that supports align error packet counts. A value of false(2) indicates that not support alignment error packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersAlignmentErrors 7.1.20540.2.2.1.1.53.22.5.1.30
A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

remotePortCountersUndersizeErrorsSupported 7.1.20540.2.2.1.1.53.22.5.1.31
A value of true(1) indicates that supports under error packet counts. A value of false(2) indicates that not support under error packet counts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

remotePortCountersUndersizeErrors 7.1.20540.2.2.1.1.53.22.5.1.32
The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rtrAllRingsGood 7.1.20540.4.1
True if all rings configured for this switch are complete.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

rtrAllRingNeighborsGood 7.1.20540.4.2
True if all neighbors in all configured rings for this switch are complete.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

rtrMasterStatus 7.1.20540.4.3
Setting to enabled(1) means that the switch is intended to be the Master in a Real-Time Ring. Setting to disabled(2) means the master will be determined automatically using a voting process in the ring algorithm.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

rtrSupportedNum 7.1.20540.4.4
The maximum number of ring entries that the switch supports.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

rtrRingTable 7.1.20540.4.10
Specifies the features of ring entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtrRingEntry

rtrRingEntry 7.1.20540.4.10.1
A conceptual row of rtrRingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RtrRingEntry  

rtrRingIndex 7.1.20540.4.10.1.1
The index of the ring entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

rtrRingCurrentStatus 7.1.20540.4.10.1.2
The current status of the switch in a ring. disabled(1) means the rtrRingStatus is invalid. localBreak(2) means ring port of the switch is link down. remoteBreak(3) means switch cannot receive RPDUs from other switches, or primary port and backup port have different master switch information. complete(3) means primary port and backup port receive the same master switch information from both directions. The master switch will put its primary port into forward(3) state, and put its backup port into discard(2) state to block traffic. Other switches in the ring will put both ports into the forward(3) state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), localBreak(2), remoteBreak(3), complete(4)  

rtrRingName 7.1.20540.4.10.1.3
The name of specified Ring entry. This name should be checked to ensure that it is unique across all rings on the switch.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

rtrRingPrimaryPortIf 7.1.20540.4.10.1.4
The primary port for that ring. This port must be checked to ensure it is not the same as any other port used in any other ring on this switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

rtrRingPrimaryPortStatus 7.1.20540.4.10.1.5
The current status of the ring primary port. down(1) means the ring port link is down. disabled(2) means ring port is disabled. discard(3) means port receives configuration messages, but does not forward packets. forward(4) means port forwards packets, and continues learning addresses.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), disabled(2), discard(3), forward(4)  

rtrRingBackupPortIf 7.1.20540.4.10.1.6
The backup port for that ring. This port must be checked to ensure it is not the same as any other port used in any other ring on this switch. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

rtrRingBackupPortStatus 7.1.20540.4.10.1.7
The current status of the ring backup port. down(1) means the ring port link is down. disabled(2) means ring port is disabled. discard(3) means port receives configuration messages, but does not forward packets. forward(4) means port forwards packets, and continues learning addresses.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), disabled(2), discard(3), forward(4)  

rtrPrimarySeen 7.1.20540.4.10.1.8
True if the switch has recently seen RPDUs from its primary neighbor on this ring.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

rtrSecondarySeen 7.1.20540.4.10.1.9
True if the switch has recently seen RPDUs from its backup neighbor on this ring.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

rtrRingStatus 7.1.20540.4.10.1.10
Set this variable to valid(1) to create an entry. Set this variable to invalid(2) to destroy an entry.
Status: current Access: read-create
OBJECT-TYPE    
  ValidStatus  

sixnetTraps 7.1.20540.2.2.1.2.1
OBJECT IDENTIFIER    

sixnetTrapsPrefix 7.1.20540.2.2.1.2.1.0
OBJECT IDENTIFIER    

swPowerStatusChangeTrap 7.1.20540.2.2.1.2.1.0.1
This trap is sent when the power state changes.
Status: current Access: read-create
NOTIFICATION-TYPE    

swPortSecurityTrap 7.1.20540.2.2.1.2.1.0.36
This trap is sent when the port is being intruded. This trap will only be sent when the portSecActionTrap is enabled.
Status: current Access: read-create
NOTIFICATION-TYPE    

swAuthenticationFailure 7.1.20540.2.2.1.2.1.0.66
This trap will be triggered if authentication is failed.
Status: current Access: read-create
NOTIFICATION-TYPE    

swAuthenticationSuccess 7.1.20540.2.2.1.2.1.0.67
This trap will be triggered if authentication is successful.
Status: current Access: read-create
NOTIFICATION-TYPE    

swLoopbackDetectionTrap 7.1.20540.2.2.1.2.1.0.92
This trap will be sent when loopback BPDUs have been detected.
Status: current Access: read-create
NOTIFICATION-TYPE    

autoUpgradeTrap 7.1.20540.2.2.1.2.1.0.104
This trap is sent when auto upgrade is executed.
Status: current Access: read-create
NOTIFICATION-TYPE    

sixnetCompliance1 7.1.20540.6.1.1
This really just keeps MIB verification programs happy because there is no external standard to which our private MIB must conform.
Status: current Access: read-create
MODULE-COMPLIANCE    

sixnetSwitchGroup 7.1.20540.6.2.1
A collection of objects providing information about SIXNET switches
Status: current Access: read-create
OBJECT-GROUP    

sixnetTestGroup 7.1.20540.6.2.2
A collection of objects for testing.
Status: current Access: read-create
OBJECT-GROUP    

portTestTable 7.1.20540.2.1.9999.1
A list of interface entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortTestEntry

portTestEntry 7.1.20540.2.1.9999.1.1
An entry containing management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortTestEntry  

testifIndex 7.1.20540.2.1.9999.1.1.1
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ifAdminSpeed 7.1.20540.2.1.9999.1.1.2
Force port speed (in megabits/sec)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER m10(10), m100(100), g1(1000)  

ifAdminPower 7.1.20540.2.1.9999.1.1.3
The PHYs PwrDown bit. ifAdminPower in the down(2) state indicates that the PHY control regsiter, bit 11 is 1 (Power Down). ifAdminPower in the up(1) date indicates that the PHY control register, bit 11 is 0 (Normal operation)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER down(0), up(1), unknown(2)  

ledTestTrigger 7.1.20540.2.1.9999.2
Trigger LED test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(0), testing(1)  

sixnetTestConfig 7.1.20540.2.1.9999.3
OBJECT IDENTIFIER    

sixnetConfigState 7.1.20540.2.1.9999.3.1
Trigger LED test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER idle(0), reserved(1), configure(2), working(3), done(4), crash(5)  

sixnetConfigResult 7.1.20540.2.1.9999.3.2
Result of configuration. Valid only when configState is done.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER success(0), failure(1), abort(99)  

sixnetConfigServer 7.1.20540.2.1.9999.3.3
The address of the configuration server. Typically an IP address but might be a FQDN.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

sixnetConfigFile 7.1.20540.2.1.9999.3.4
The file to retrieve and process.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

fallbackFirmware 7.1.20540.5.0.1
A fallbackFirmware trap indicates that the switch failed to boot the default firmware and has instead booted up running the backup firmware. This could mean that the switch lost power during its last bootup and was unable to finish, or it could mean that the default firmware has become corrupt.
Status: current Access: read-write
NOTIFICATION-TYPE    

firmwareUpdateComplete 7.1.20540.5.0.2
A firmware update started via SNMP has completed. Use the firmwareHealth column of the firmwareTable to determine whether the update was successful.
Status: current Access: read-write
NOTIFICATION-TYPE