SLA-MONITOR-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
INET-ADDRESS-MIB	RFC1213-MIB	DIFFSERV-DSCP-TC
SNMP-FRAMEWORK-MIB	SYNOPTICS-ROOT-MIB

Imported symbols

Unsigned32	MODULE-IDENTITY	OBJECT-TYPE
NOTIFICATION-TYPE	Integer32	StorageType
RowStatus	MODULE-COMPLIANCE	OBJECT-GROUP
InetAddressType	InetAddress	InetPortNumber
DisplayString	Dscp	SnmpAdminString
policy

Defined Types

SlaMonitorNtrCtrlEntry
SEQUENCE
	slaMonitorNtrCtrlOwnerId	SnmpAdminString
	slaMonitorNtrCtrlTestName	SnmpAdminString
	slaMonitorNtrCtrlTargetAddressType	InetAddressType
	slaMonitorNtrCtrlTargetAddress	InetAddress
	slaMonitorNtrCtrlDscp	Dscp
	slaMonitorNtrCtrlAttempts	Integer32
	slaMonitorNtrCtrlPeriod	Integer32
	slaMonitorNtrCtrlAdminStatus	INTEGER
	slaMonitorNtrCtrlLabel	SnmpAdminString
	slaMonitorNtrCtrlStorageType	StorageType
	slaMonitorNtrCtrlRowStatus	RowStatus

SlaMonitorNtrResultsEntry
SEQUENCE
	slaMonitorNtrResultsOperStatus	INTEGER
	slaMonitorNtrResultsSrcAddressType	InetAddressType
	slaMonitorNtrResultsSrcAddress	InetAddress
	slaMonitorNtrResultsDstAddressType	InetAddressType
	slaMonitorNtrResultsDstAddress	InetAddress
	slaMonitorNtrResultsSrcPort	InetPortNumber
	slaMonitorNtrResultsDstPort	InetPortNumber
	slaMonitorNtrResultsDscp	Dscp
	slaMonitorNtrResultsTTL	Unsigned32
	slaMonitorNtrResultsCompletionData	BITS
	slaMonitorNtrResultsCompletionSummary	SnmpAdminString
	slaMonitorNtrResultsAbortData	BITS
	slaMonitorNtrResultsHopCount	Unsigned32

SlaMonitorNtrHopsEntry
SEQUENCE
	slaMonitorNtrHopsHopIndex	Unsigned32
	slaMonitorNtrHopsTgtAddressType	InetAddressType
	slaMonitorNtrHopsTgtAddress	InetAddress
	slaMonitorNtrHopsRtt	Unsigned32
	slaMonitorNtrHopsIngressDscp	Dscp
	slaMonitorNtrHopsEgressDscp	Dscp

SlaMonitorRtpCtrlEntry
SEQUENCE
	slaMonitorRtpCtrlOwnerId	SnmpAdminString
	slaMonitorRtpCtrlTestName	SnmpAdminString
	slaMonitorRtpCtrlTargetAddressType	InetAddressType
	slaMonitorRtpCtrlTargetAddress	InetAddress
	slaMonitorRtpCtrlDscp	Dscp
	slaMonitorRtpCtrlTestPackets	Integer32
	slaMonitorRtpCtrlSyncPackets	Integer32
	slaMonitorRtpCtrlPeriod	Integer32
	slaMonitorRtpCtrlAdminStatus	INTEGER
	slaMonitorRtpCtrlLabel	SnmpAdminString
	slaMonitorRtpCtrlStorageType	StorageType
	slaMonitorRtpCtrlRowStatus	RowStatus

SlaMonitorRtpResultsEntry
SEQUENCE
	slaMonitorRtpResultsOperStatus	INTEGER
	slaMonitorRtpResultsSrcAddressType	InetAddressType
	slaMonitorRtpResultsSrcAddress	InetAddress
	slaMonitorRtpResultsDstAddressType	InetAddressType
	slaMonitorRtpResultsDstAddress	InetAddress
	slaMonitorRtpResultsSrcPort	InetPortNumber
	slaMonitorRtpResultsDstPort	InetPortNumber
	slaMonitorRtpResultsDscp	Dscp
	slaMonitorRtpResultsAverageDelay	Unsigned32
	slaMonitorRtpResultsMedianDelay	Unsigned32
	slaMonitorRtpResultsPacketLoss	Unsigned32
	slaMonitorRtpResultsOutOfOrderArrivals	Unsigned32
	slaMonitorRtpResultsJitterQuartile0	Unsigned32
	slaMonitorRtpResultsJitterQuartile1	Unsigned32
	slaMonitorRtpResultsJitterQuartile2	Unsigned32
	slaMonitorRtpResultsJitterQuartile3	Unsigned32
	slaMonitorRtpResultsJitterQuartile4	Unsigned32
	slaMonitorRtpResultsAbortData	BITS

Defined Values

slaMonitorMib		1.3.6.1.4.1.45.4.8
An Avaya management module containing data definitions related to the SLA Monitor Agent.
MODULE-IDENTITY

slaMonitorMibNotifications		1.3.6.1.4.1.45.4.8.0
OBJECT IDENTIFIER

slaMonitorMibClasses		1.3.6.1.4.1.45.4.8.1
OBJECT IDENTIFIER

slaMonitorMibConformance		1.3.6.1.4.1.45.4.8.2
OBJECT IDENTIFIER

slaMonitorAgtClasses		1.3.6.1.4.1.45.4.8.1.1
OBJECT IDENTIFIER

slaMonitorAgentStatus		1.3.6.1.4.1.45.4.8.1.1.1
The value of this attribute indicates whether the SLA Monitor agent is enabled or not. An agent that is enabled will respond to SLA Monitor server discovery packets. A disabled agent will remain dormant until manually enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

slaMonitorAgentAddressType		1.3.6.1.4.1.45.4.8.1.1.2
The type of IP address used by the agent. This object is limited to IPv4 and IPv6 addresses.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorAgentAddress		1.3.6.1.4.1.45.4.8.1.1.3
The IP address currently used by the SLA Monitor agent.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorAgentPort		1.3.6.1.4.1.45.4.8.1.1.4
The UDP port currently used by the SLA Monitor agent for agent-server communication.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentRegisteredWithServer		1.3.6.1.4.1.45.4.8.1.1.5
The value of this attribute indicates whether the SLA Monitor agent is registered with an SLA Monitor server or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	registered(1), notRegistered(2)

slaMonitorAgentRegisteredServerAddrType		1.3.6.1.4.1.45.4.8.1.1.6
The type of IP address used by the server. This object is limited to IPv4 and IPv6 addresses.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorAgentRegisteredServerAddr		1.3.6.1.4.1.45.4.8.1.1.7
The IP address of the SLA Monitor server with which the agent is currently registered.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorAgentRegisteredServerPort		1.3.6.1.4.1.45.4.8.1.1.8
The TCP port utilized by the SLA Monitor server with which the agent is currently registered.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentRegistrationTime		1.3.6.1.4.1.45.4.8.1.1.9
Specifies the maximum amount of time, in seconds, until the current registration period expires.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorAgentCliAvailable		1.3.6.1.4.1.45.4.8.1.1.10
The value of this attribute indicates whether the SLA Monitor agent CLI is available or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	available(1), notAvailable(2)

slaMonitorAgentCliTimeout		1.3.6.1.4.1.45.4.8.1.1.11
Specifies the maximum amount of time, in seconds, until the CLI session is automatically terminated. The value of this attribute is pertinent only if CLI timeouts are enabled (slaMonitorAgentCliTimeoutMode equals 'enable(1)').
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

slaMonitorAgentCliTimeoutMode		1.3.6.1.4.1.45.4.8.1.1.12
The value of this attribute indicates whether the SLA Monitor agent automatic CLI session timeout is enabled or not. When this attribute is set to 'enable(1)', a CLI session will automatically timeout after slaMonitorAgentCliTimeout seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

slaMonitorAgentSupportedApps		1.3.6.1.4.1.45.4.8.1.1.13
An enumeration of the SLA Monitor agent capabilities.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), ntr(1), rtp(2)

slaMonitorAgentConfiguredAgentAddrType		1.3.6.1.4.1.45.4.8.1.1.14
The type of IP address used by the agent. This object is limited to IPv4 and IPv6 addresses.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

slaMonitorAgentConfiguredAgentAddr		1.3.6.1.4.1.45.4.8.1.1.15
The IP address of the SLA Monitor agent. If the value of this attribute is 0.0.0.0, the SLA Monitor agent will utilize an active device IP address by default.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

slaMonitorAgentConfiguredAgentPort		1.3.6.1.4.1.45.4.8.1.1.16
The UDP port utilized by the SLA Monitor agent for agent-server communication. If the value of this attribute is zero, the SLA Monitor agent will utilize a default port value for communication purposes.
Status: current	Access: read-write
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentConfiguredServerAddrType		1.3.6.1.4.1.45.4.8.1.1.17
The type of IP address used by the server. This object is limited to IPv4 and IPv6 addresses.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

slaMonitorAgentConfiguredServerAddr		1.3.6.1.4.1.45.4.8.1.1.18
The IP address of the SLA Monitor server with which the agent is allowed to register. If the value of this attribute is not 0.0.0.0, the SLA Monitor agent may only respond to server requests originating at the specified IP address (or the IP address specified by the slaMonitorAgentConfiguredAltServerAddr object if it is non-zero).
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

slaMonitorAgentConfiguredServerPort		1.3.6.1.4.1.45.4.8.1.1.19
The TCP port utilized by the SLA Monitor server with which the agent is allowed to register. If the value of this attribute is non-zero, the SLA Monitor agent may only respond to server requests originating from the specified port (or from the port specified by the slaMonitorAgentConfiguredAltServerPort object if it is non-zero).
Status: current	Access: read-write
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentConfiguredAltServerAddrType		1.3.6.1.4.1.45.4.8.1.1.20
The type of IP address used by the server. This object is limited to IPv4 and IPv6 addresses.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

slaMonitorAgentConfiguredAltServerAddr		1.3.6.1.4.1.45.4.8.1.1.21
The IP address of the alternate SLA Monitor server with which the agent is allowed to register. If the value of this attribute is not 0.0.0.0, the SLA Monitor agent may only respond to server requests originating at the specified IP address (or the IP address specified by the slaMonitorAgentConfiguredServerAddr object if it is non-zero).
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

slaMonitorAgentConfiguredAltServerPort		1.3.6.1.4.1.45.4.8.1.1.22
The TCP port utilized by the alternate SLA Monitor server with which the agent is allowed to register. If the value of this attribute is non-zero, the SLA Monitor agent may only respond to server requests originating from the specified port (or from the port specified by the slaMonitorAgentConfiguredServerPort object if it is non-zero).
Status: current	Access: read-write
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentToAgentPort		1.3.6.1.4.1.45.4.8.1.1.23
The base UDP port currently used by the SLA Monitor agent for agent-agent communication. The base UDP port is used to derive multiple agent communication ports. An even base port values causes slaMonitorAgentToAgentPort and slaMonitorAgentToAgentPort+1 ports to be used. An odd base port values causes slaMonitorAgentToAgentPort and slaMonitorAgentToAgentPort-1 ports to be used.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentConfiguredAgentToAgentPort		1.3.6.1.4.1.45.4.8.1.1.24
The UDP port utilized by the SLA Monitor agent for agent-agent communication. If the value of this attribute is zero, the SLA Monitor agent will utilize a default port value for the base agent-agent UDP communication port.
Status: current	Access: read-write
OBJECT-TYPE
	InetPortNumber

slaMonitorAgentEncryptionSupport		1.3.6.1.4.1.45.4.8.1.1.25
Specifies if encrypted agent-server communication is supported by the agent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	available(1), notAvailable(2)

slaMonitorAgentConfiguredAgentVrfName		1.3.6.1.4.1.45.4.8.1.1.26
The name of the virtual Router which SLA Monitor Agent IP address (slaMonitorAgentConfiguredAgentAddr) is associated with. This is only supported on VSP9K for now
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

slaMonitorAgentSlaParameter		1.3.6.1.4.1.45.4.8.1.1.27
String directly passed to the SLA Agent as parameter
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..80)

slaMonitorAgentCertFileInstallAction		1.3.6.1.4.1.45.4.8.1.1.28
Operation object to install and deinstall the certificate file to a platform specific location. 'noactio' -is default setting and always is returned when this object is queried. 'install', object slaMonitorAgentCertFile will be used as source certificate file to install . 'deinstall', will ignore object slaMonitorAgentCertFile and just deinstall or remove the certificate file from the installed location
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAction(1), install(2), deinstall(3)

slaMonitorAgentCertFile		1.3.6.1.4.1.45.4.8.1.1.29
the certification file name for installation. It is only valid or used when object slaMonitorAgentCertFileInstallAction is set to install. Otherwise, it will be ignored
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

slaMonitorAgentServerBypass		1.3.6.1.4.1.45.4.8.1.1.30
The value of this attribute determines whether the SLA Monitor agent can perform certain operations without being registered with a server. When this attribute is set to 'enable(1)', an agent will respond to agent-to-agent test requests regardless of the server registration status. A 'disable(2)' setting will restrict agent responses when the agent is not registered with an SLA Monitor server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

slaMonitorAgentRefuseServerTests		1.3.6.1.4.1.45.4.8.1.1.31
The value of this attribute determines whether the SLA Monitor agent will refuse test requests from the server. When this attribute is set to 'allow(1)', an agent will accept test requests from the server. A 'refuse(2)' setting will cause the agent to reject test requests from the server. From a usage perspective, it may be necessary to temporarily refuse server test requests if the agent is being actively managed by a server but the administrator wishes to use the CLI or SNMP interfaces to initiate tests manually.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allow(1), refuse(2)

slaMonitorAgtTestClasses		1.3.6.1.4.1.45.4.8.1.2
OBJECT IDENTIFIER

slaMonitorNtrCtrlTable		1.3.6.1.4.1.45.4.8.1.2.1
Defines the SLAMon agent NTR test control table supporting the ability to initiate NTR tests remotely. The results of NTR test operations are stored in the slaMonitorNtrResultsTable and the slaMonitorNtrHopsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SlaMonitorNtrCtrlEntry

slaMonitorNtrCtrlEntry		1.3.6.1.4.1.45.4.8.1.2.1.1
Defines an entry in the slaMonitorNtrCtrlTable. The first index element, slaMonitorNtrCtrlOwnerId, is of type SnmpAdminString, allowing for a management application to identify its entries. The second index, slaMonitorNtrCtrlTestName (also an SnmpAdminString), enables the same management application to have multiple requests configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SlaMonitorNtrCtrlEntry

slaMonitorNtrCtrlOwnerId		1.3.6.1.4.1.45.4.8.1.2.1.1.1
The owner of an NTR test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

slaMonitorNtrCtrlTestName		1.3.6.1.4.1.45.4.8.1.2.1.1.2
The name of an NTR test. This value is locally unique, within the scope of an slaMonitorNtrCtrlOwnerId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

slaMonitorNtrCtrlTargetAddressType		1.3.6.1.4.1.45.4.8.1.2.1.1.3
Specifies the target address type.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

slaMonitorNtrCtrlTargetAddress		1.3.6.1.4.1.45.4.8.1.2.1.1.4
Specifies the target address used for the NTR test. The address type can be determined by examining the value of the corresponding slaMonitorNtrCtrlTargetAddressType. A value for this object MUST be provided during entry creation.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

slaMonitorNtrCtrlDscp		1.3.6.1.4.1.45.4.8.1.2.1.1.5
Specifies the DSCP value for use in packets that are generated by the NTR test.
Status: current	Access: read-create
OBJECT-TYPE
	Dscp

slaMonitorNtrCtrlAttempts		1.3.6.1.4.1.45.4.8.1.2.1.1.6
Specifies the number of attempts are generated by the NTR test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..10

slaMonitorNtrCtrlPeriod		1.3.6.1.4.1.45.4.8.1.2.1.1.7
Specifies the interval between packets, in microseconds, generated by the NTR test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	10000..200000

slaMonitorNtrCtrlAdminStatus		1.3.6.1.4.1.45.4.8.1.2.1.1.8
Used to initiate an NTR test: enabled(1) - initiate the test as defined by this slaMonitorNtrCtrlEntry. disabled(2) - deactivate the test defined by this slaMonitorNtrCtrlEntry, if possible. Refer to the corresponding slaMonitorNtrResultsOperStatus to determine the operational state of the test defined by this entry. When queried, 'disabled(2)' is always returned for this attribute.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

slaMonitorNtrCtrlLabel		1.3.6.1.4.1.45.4.8.1.2.1.1.9
A label used to reference the NTR control entry in a textual manner.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

slaMonitorNtrCtrlStorageType		1.3.6.1.4.1.45.4.8.1.2.1.1.10
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

slaMonitorNtrCtrlRowStatus		1.3.6.1.4.1.45.4.8.1.2.1.1.11
This object allows entries to be created and deleted in the slaMonitorNtrCtrlTable. Deletion of an entry in this table results in the deletion of all corresponding (i.e., entries with the same slaMonitorNtrCtrlOwnerId and slaMonitorNtrCtrlTestName index values) entries in the slaMonitorNtrResultsTable and the slaMonitorNtrHopsTable. Initiation of an NTR test corresponding to this entry is controlled via slaMonitorNtrCtrlAdminStatus and not by entry creation. The operational state of an NTR test can be determined by examining the corresponding slaMonitorNtrResultsOperStatus object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

slaMonitorNtrResultsTable		1.3.6.1.4.1.45.4.8.1.2.2
Defines the SLAMon agent NTR results table that is used to track the status of NTR tests initiated through the the slaMonitorNtrCtrlTable. An entry is added to the slaMonitorNtrResultsTable when an NTR test defined by an slaMonitorNtrCtrlEntry is started by transition of its slaMonitorNtrCtrlAdminStatus object to 'enabled(1)'. If the object slaMonitorNtrCtrlAdminStatus has the value 'disabled(2)', then successfully writing 'enabled(1)' to the object slaMonitorNtrCtrlAdminStatus re-initializes an already existing entry in the slaMonitorNtrResultsTable. The values of objects in the re-initialized entry are the same as the values of objects in a new entry would be. An entry is removed from the slaMonitorNtrResultsTable when its corresponding slaMonitorNtrCtrlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SlaMonitorNtrResultsEntry

slaMonitorNtrResultsEntry		1.3.6.1.4.1.45.4.8.1.2.2.1
Defines an entry in the slaMonitorNtrResultsTable. The slaMonitorNtrResultsTable has the same indexing as the slaMonitorNtrCtrlTable so that a slaMonitorNtrResultsEntry corresponds to the slaMonitorNtrCtrlEntry that caused it to be created.
Status: current	Access: not-accessible
OBJECT-TYPE
	SlaMonitorNtrResultsEntry

slaMonitorNtrResultsOperStatus		1.3.6.1.4.1.45.4.8.1.2.2.1.1
Reflects the operational state of an slaMonitorNtrCtrlEntry: inProgress(1) - test is active. aborted(2) - test has been stopped. Refer to object slaMonitorNtrResultsAbortData for details. completed(3) - test is completed. Refer to objects slaMonitorNtrResultsCompletionData and slaMonitorNtrResultsCompletionSummary for details.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inProgress(1), aborted(2), completed(3)

slaMonitorNtrResultsSrcAddressType		1.3.6.1.4.1.45.4.8.1.2.2.1.2
Specifies the address type of the source IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorNtrResultsSrcAddress		1.3.6.1.4.1.45.4.8.1.2.2.1.3
Specifies the source IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorNtrResultsDstAddressType		1.3.6.1.4.1.45.4.8.1.2.2.1.4
Specifies the address type of the destination IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorNtrResultsDstAddress		1.3.6.1.4.1.45.4.8.1.2.2.1.5
Specifies the destination IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorNtrResultsSrcPort		1.3.6.1.4.1.45.4.8.1.2.2.1.6
Specifies the Layer 4 source port used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorNtrResultsDstPort		1.3.6.1.4.1.45.4.8.1.2.2.1.7
Specifies the Layer 4 destination port used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorNtrResultsDscp		1.3.6.1.4.1.45.4.8.1.2.2.1.8
Specifies the DSCP value contained in NTR test packets generated by the agent for this test.
Status: current	Access: read-only
OBJECT-TYPE
	Dscp

slaMonitorNtrResultsTTL		1.3.6.1.4.1.45.4.8.1.2.2.1.9
The maximum time-to-live (TTL) value used during the execution of this test.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorNtrResultsCompletionData		1.3.6.1.4.1.45.4.8.1.2.2.1.10
Provides details related to test completion. Multiple bits may be set to convey test status.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), remoteUnreachable(1), remotePortUnreachable(2), remoteNetUnreachable(3), remoteHostUnreachable(4), remoteProtocolUnreachable(5), remoteFirewalledUnreachable(6), remoteResponded(7), remoteResponseLikely(8), remoteNoResponse(9)

slaMonitorNtrResultsCompletionSummary		1.3.6.1.4.1.45.4.8.1.2.2.1.11
A user-readable string that is used to convey test results for completed tests in an easy-to-understand format.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

slaMonitorNtrResultsAbortData		1.3.6.1.4.1.45.4.8.1.2.2.1.12
Provides details for tests that were aborted. Multiple bits may be set to convey test status.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), agentDisabled(1), agentBusy(2), timeout(3), cancelled(4)

slaMonitorNtrResultsHopCount		1.3.6.1.4.1.45.4.8.1.2.2.1.13
The total number of hops for which information has been acquired during the execution of this test.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorNtrHopsTable		1.3.6.1.4.1.45.4.8.1.2.3
Defines the SLAMon agent NTR test hop table for keeping track of the results of NTR tests on a per-hop basis.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SlaMonitorNtrHopsEntry

slaMonitorNtrHopsEntry		1.3.6.1.4.1.45.4.8.1.2.3.1
Defines an entry in the slaMonitorNtrHopsTable. The first two index elements identify the slaMonitorNtrCtrlEntry with which this slaMonitorNtrHopsEntry is associated. The third index element, slaMonitorNtrHopsHopIndex, selects a hop in an NTR test path.
Status: current	Access: not-accessible
OBJECT-TYPE
	SlaMonitorNtrHopsEntry

slaMonitorNtrHopsHopIndex		1.3.6.1.4.1.45.4.8.1.2.3.1.1
Specifies the hop index for an NTR test hop. Values for this object with respect to the same slaMonitorNtrCtrlOwnerId and slaMonitorNtrCtrlTestName MUST start at 1 and be given increasing values for subsequent hops. The value of slaMonitorNtrHopsHopIndex does not necessarily represent the number of the hop on the traced path, though this is normally the case.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..ffffffff

slaMonitorNtrHopsTgtAddressType		1.3.6.1.4.1.45.4.8.1.2.3.1.2
This object indicates the type of address stored in the corresponding slaMonitorNtrHopsTgtAddress object.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorNtrHopsTgtAddress		1.3.6.1.4.1.45.4.8.1.2.3.1.3
This object reports the IP address associated with the NTR test hop.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorNtrHopsRtt		1.3.6.1.4.1.45.4.8.1.2.3.1.4
The NTR test round-trip-time (RTT), in microseconds, computed for this hop.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorNtrHopsIngressDscp		1.3.6.1.4.1.45.4.8.1.2.3.1.5
The DSCP value in the NTR test packet received by the target host (slaMonitorNtrHopsTgtAddress) for this hop.
Status: current	Access: read-only
OBJECT-TYPE
	Dscp

slaMonitorNtrHopsEgressDscp		1.3.6.1.4.1.45.4.8.1.2.3.1.6
The DSCP value in the NTR test response packet received by the SLAMon agent for this hop.
Status: current	Access: read-only
OBJECT-TYPE
	Dscp

slaMonitorRtpCtrlTable		1.3.6.1.4.1.45.4.8.1.2.4
Defines the SLAMon agent RTP test control table supporting the ability to initiate RTP tests remotely. The results of RTP test operations are stored in the slaMonitorRtpResultsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SlaMonitorRtpCtrlEntry

slaMonitorRtpCtrlEntry		1.3.6.1.4.1.45.4.8.1.2.4.1
Defines an entry in the slaMonitorRtpCtrlTable. The first index element, slaMonitorRtpCtrlOwnerId, is of type SnmpAdminString, allowing for a management application to identify its entries. The second index, slaMonitorRtpCtrlTestName (also an SnmpAdminString), enables the same management application to have multiple requests configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SlaMonitorRtpCtrlEntry

slaMonitorRtpCtrlOwnerId		1.3.6.1.4.1.45.4.8.1.2.4.1.1
The owner of an RTP test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

slaMonitorRtpCtrlTestName		1.3.6.1.4.1.45.4.8.1.2.4.1.2
The name of an RTP test. This is locally unique, within the scope of an slaMonitorRtpCtrlOwnerId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

slaMonitorRtpCtrlTargetAddressType		1.3.6.1.4.1.45.4.8.1.2.4.1.3
Specifies the target address type.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

slaMonitorRtpCtrlTargetAddress		1.3.6.1.4.1.45.4.8.1.2.4.1.4
Specifies the target address used for the RTP test. The address type can be determined by examining the value of the corresponding slaMonitorRtpCtrlTargetAddressType. A value for this object MUST be provided during entry creation.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

slaMonitorRtpCtrlDscp		1.3.6.1.4.1.45.4.8.1.2.4.1.5
Specifies the DSCP value for use in packets that are generated by the RTP test.
Status: current	Access: read-create
OBJECT-TYPE
	Dscp

slaMonitorRtpCtrlTestPackets		1.3.6.1.4.1.45.4.8.1.2.4.1.6
Specifies the number of test packets that are generated by the RTP test. Test packets are used for jitter determination.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	10..100

slaMonitorRtpCtrlSyncPackets		1.3.6.1.4.1.45.4.8.1.2.4.1.7
Specifies the number of synchronization packets that are generated by the RTP test. Sync packets are used for network delay determination.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	10..100

slaMonitorRtpCtrlPeriod		1.3.6.1.4.1.45.4.8.1.2.4.1.8
Specifies the interval between packets (in microseconds) generated by the RTP test.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	10000..200000

slaMonitorRtpCtrlAdminStatus		1.3.6.1.4.1.45.4.8.1.2.4.1.9
Used to initiate an RTP test: enabled(1) - initiate the test as defined by this slaMonitorRtpCtrlEntry. disabled(2) - deactivate the test defined by this slaMonitorRtpCtrlEntry, if possible. Refer to the corresponding slaMonitorRtpResultsOperStatus to determine the operational state of the test defined by this entry. When queried, 'disabled(2)' is always returned for this attribute.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

slaMonitorRtpCtrlLabel		1.3.6.1.4.1.45.4.8.1.2.4.1.10
A label used to reference the RTP control entry in a textual manner.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

slaMonitorRtpCtrlStorageType		1.3.6.1.4.1.45.4.8.1.2.4.1.11
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

slaMonitorRtpCtrlRowStatus		1.3.6.1.4.1.45.4.8.1.2.4.1.12
This object allows entries to be created and deleted in the slaMonitorRtpCtrlTable. Deletion of an entry in this table results in the deletion of all corresponding (i.e., entries with the same slaMonitorRtpCtrlOwnerId and slaMonitorRtpCtrlTestName index values) entries in the slaMonitorRtpResultsTable. Initiation of an RTP test corresponding to this entry is controlled via slaMonitorRtpCtrlAdminStatus and not by entry creation. The operational state of an RTP test can be determined by examining the corresponding slaMonitorRtpResultsOperStatus object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

slaMonitorRtpResultsTable		1.3.6.1.4.1.45.4.8.1.2.5
Defines the SLAMon agent RTP results table that is used to track the status of RTP tests initiated through the the slaMonitorRtpCtrlTable. An entry is added to the slaMonitorRtpResultsTable when an RTP test defined by an slaMonitorRtpCtrlEntry is started by transition of its slaMonitorRtpCtrlAdminStatus object to 'enabled(1)'. If the object slaMonitorRtpCtrlAdminStatus has the value 'disabled(2)', then successfully writing 'enabled(1)' to the object slaMonitorRtpCtrlAdminStatus re-initializes an already existing entry in the slaMonitorRtpResultsTable. The values of objects in the re-initialized entry are the same as the values of objects in a new entry would be. An entry is removed from the slaMonitorRtpResultsTable when its corresponding slaMonitorRtpCtrlEntry is deleted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SlaMonitorRtpResultsEntry

slaMonitorRtpResultsEntry		1.3.6.1.4.1.45.4.8.1.2.5.1
Defines an entry in the slaMonitorRtpResultsTable. The slaMonitorRtpResultsTable has the same indexing as the slaMonitorRtpCtrlTable so that a slaMonitorRtpResultsEntry corresponds to the slaMonitorRtpCtrlEntry that caused it to be created.
Status: current	Access: not-accessible
OBJECT-TYPE
	SlaMonitorRtpResultsEntry

slaMonitorRtpResultsOperStatus		1.3.6.1.4.1.45.4.8.1.2.5.1.1
Reflects the operational state of an slaMonitorRtpCtrlEntry: inProgress(1) - test is active. aborted(2) - test has been stopped. Refer to object slaMonitorRtpResultsAbortData for details. completed(3) - test is completed. Refer to objects that contain completed test results (all attributes except slaMonitorRtpResultsAbortData) for details.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inProgress(1), aborted(2), completed(3)

slaMonitorRtpResultsSrcAddressType		1.3.6.1.4.1.45.4.8.1.2.5.1.2
Specifies the address type of the source IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorRtpResultsSrcAddress		1.3.6.1.4.1.45.4.8.1.2.5.1.3
Specifies the source IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorRtpResultsDstAddressType		1.3.6.1.4.1.45.4.8.1.2.5.1.4
Specifies the address type of the destination IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

slaMonitorRtpResultsDstAddress		1.3.6.1.4.1.45.4.8.1.2.5.1.5
Specifies the destination IP address used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

slaMonitorRtpResultsSrcPort		1.3.6.1.4.1.45.4.8.1.2.5.1.6
Specifies the Layer 4 source port used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorRtpResultsDstPort		1.3.6.1.4.1.45.4.8.1.2.5.1.7
Specifies the Layer 4 destination port used for this test.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

slaMonitorRtpResultsDscp		1.3.6.1.4.1.45.4.8.1.2.5.1.8
Specifies the DSCP value contained in RTP test packets generated by the agent for this test.
Status: current	Access: read-only
OBJECT-TYPE
	Dscp

slaMonitorRtpResultsAverageDelay		1.3.6.1.4.1.45.4.8.1.2.5.1.9
The average network delay (RTT) experienced during this test sequence, in microseconds.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsMedianDelay		1.3.6.1.4.1.45.4.8.1.2.5.1.10
The median network delay (RTT) experienced during this test sequence, in microseconds.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsPacketLoss		1.3.6.1.4.1.45.4.8.1.2.5.1.11
A count of packets lost during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsOutOfOrderArrivals		1.3.6.1.4.1.45.4.8.1.2.5.1.12
The number of out-of-order arrivals detected during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsJitterQuartile0		1.3.6.1.4.1.45.4.8.1.2.5.1.13
The quartile 0 network jitter value, in microseconds, experienced during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsJitterQuartile1		1.3.6.1.4.1.45.4.8.1.2.5.1.14
The quartile 1 network jitter value, in microseconds, experienced during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsJitterQuartile2		1.3.6.1.4.1.45.4.8.1.2.5.1.15
The quartile 2 network jitter value, in microseconds, experienced during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsJitterQuartile3		1.3.6.1.4.1.45.4.8.1.2.5.1.16
The quartile 3 network jitter value, in microseconds, experienced during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsJitterQuartile4		1.3.6.1.4.1.45.4.8.1.2.5.1.17
The quartile 4 network jitter value, in microseconds, experienced during this test sequence.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

slaMonitorRtpResultsAbortData		1.3.6.1.4.1.45.4.8.1.2.5.1.18
Provides details for tests that were aborted. Multiple bits may be set to convey test status.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), agentDisabled(1), agentBusy(2), timeout(3), cancelled(4), deniedByTarget(5), networkIssue(6), timeSync(7)

slaMonitorAgentExceptionDetected		1.3.6.1.4.1.45.4.8.0.1
Indicates that an exception event that impacts the local SLA Monitor agent has been detected.
Status: current	Access: read-only
NOTIFICATION-TYPE

slaMonitorMibCompliances		1.3.6.1.4.1.45.4.8.2.1
OBJECT IDENTIFIER

slaMonitorMibGroups		1.3.6.1.4.1.45.4.8.2.2
OBJECT IDENTIFIER

slaMonitorMibCompliance		1.3.6.1.4.1.45.4.8.2.1.1
Describes the requirements for conformance to the Avaya Networks SLA Monitor Agent MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

slaMonitorAgentConfigGroup		1.3.6.1.4.1.45.4.8.2.2.1
Objects used for SLA Monitor Agent configuration and monitoring.
Status: current	Access: read-only
OBJECT-GROUP

slaMonitorAgentNtrTestGroup		1.3.6.1.4.1.45.4.8.2.2.2
Objects used for SLA Monitor Agent NTR test execution and results reporting.
Status: current	Access: read-only
OBJECT-GROUP

slaMonitorAgentRtpTestGroup		1.3.6.1.4.1.45.4.8.2.2.3
Objects used for SLA Monitor Agent RTP test execution and results reporting.
Status: current	Access: read-only
OBJECT-GROUP