SLE-MPLS-TP-TUNNEL-MIB

File: SLE-MPLS-TP-TUNNEL-MIB.mib (25001 bytes)

Imported modules

DASAN-SMI	IF-MIB	MPLS-TC-EXT-STD-MIB
MPLS-TC-STD-MIB	SLE-TC-MIB	SNMPv2-SMI
SNMPv2-TC

Imported symbols

sleMgmt	ifGeneralInformationGroup	ifCounterDiscontinuityGroup
InterfaceIndexOrZero	MplsCcId	MplsIccId
mplsStdMIB	MplsLabel	SleControlStatusType
SleControlRequestResultType	zeroDotZero	TimeTicks
IpAddress	Unsigned32	Gauge32
OBJECT-TYPE	MODULE-IDENTITY	OBJECT-IDENTITY
MacAddress

Defined Types

SleMplsTpTunnelCfgInfoEntry
SEQUENCE
	sleMplsTpTunnelCfgInfoIndex	Unsigned32
	sleMplsTpTunnelCfgInfoName	OCTET STRING
	sleMplsTpTunnelCfgInfoId	Unsigned32
	sleMplsTpTunnelCfgInfoSrcIdType	INTEGER
	sleMplsTpTunnelCfgInfoSrcGId	Unsigned32
	sleMplsTpTunnelCfgInfoSrcCc	MplsCcId
	sleMplsTpTunnelCfgInfoSrcIcc	MplsIccId
	sleMplsTpTunnelCfgInfoSrcNodeId	IpAddress
	sleMplsTpTunnelCfgInfoDestIdType	INTEGER
	sleMplsTpTunnelCfgInfoDestGId	Unsigned32
	sleMplsTpTunnelCfgInfoDestCc	MplsCcId
	sleMplsTpTunnelCfgInfoDestIcc	MplsIccId
	sleMplsTpTunnelCfgInfoDestNodeId	IpAddress
	sleMplsTpTunnelCfgInfoMode	INTEGER
	sleMplsTpTunnelCfgInfoFwdInLabel	MplsLabel
	sleMplsTpTunnelCfgInfoFwdInIfIndex	InterfaceIndexOrZero
	sleMplsTpTunnelCfgInfoFwdOperation	INTEGER
	sleMplsTpTunnelCfgInfoFwdOutLabel	MplsLabel
	sleMplsTpTunnelCfgInfoFwdOutIfIndex	InterfaceIndexOrZero
	sleMplsTpTunnelCfgInfoFwdOutMac	MacAddress
	sleMplsTpTunnelCfgInfoRevInLabel	MplsLabel
	sleMplsTpTunnelCfgInfoRevInIfIndex	InterfaceIndexOrZero
	sleMplsTpTunnelCfgInfoRevOperation	INTEGER
	sleMplsTpTunnelCfgInfoRevOutLabel	MplsLabel
	sleMplsTpTunnelCfgInfoRevOutIfIndex	InterfaceIndexOrZero
	sleMplsTpTunnelCfgInfoRevOutMac	MacAddress
	sleMplsTpTunnelCfgInfoState	INTEGER
	sleMplsTpTunnelCfgInfoRole	INTEGER
	sleMplsTpTunnelCfgInfoAssociateTnlName	OCTET STRING
	sleMplsTpTunnelCfgInfoDescription	OCTET STRING
	sleMplsTpTunnelCfgInfoHlspRole	INTEGER
	sleMplsTpTunnelCfgInfoHlspServerTunnelName	OCTET STRING
	sleMplsTpTunnelCfgInfoQosPolicyName	OCTET STRING

Defined Values

sleMplsTpTunnel		1.3.6.1.4.1.6296.101.16.14
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999
MODULE-IDENTITY

sleMpls		1.3.6.1.4.1.6296.101.16
SLE MPLS.
Status: current	Access: read-only
OBJECT-IDENTITY

sleMplsTpTunnelCfg		1.3.6.1.4.1.6296.101.16.14.1
OBJECT IDENTIFIER

sleMplsTpTunnelCfgInfoTable		1.3.6.1.4.1.6296.101.16.14.1.1
The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multipoint-to-point and point- to-multipoint connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SleMplsTpTunnelCfgInfoEntry

sleMplsTpTunnelCfgInfoEntry		1.3.6.1.4.1.6296.101.16.14.1.1.1
An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signalling protocol. Whenever a new entry is created with mplsTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2863). The ifType of this entry is mplsTunnel(150). A tunnel entry needs to be uniquely identified across a MPLS network. Indices mplsTunnelIndex and mplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. To uniquely identify a tunnel across an MPLS network requires index mplsTunnelIngressLSRId. The last index mplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that terminate on the same egress LSR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SleMplsTpTunnelCfgInfoEntry

sleMplsTpTunnelCfgInfoIndex		1.3.6.1.4.1.6296.101.16.14.1.1.1.1
A unique value which identify an entry in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..65535

sleMplsTpTunnelCfgInfoName		1.3.6.1.4.1.6296.101.16.14.1.1.1.2
The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2863.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..16)

sleMplsTpTunnelCfgInfoId		1.3.6.1.4.1.6296.101.16.14.1.1.1.3
Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the value signaled in the Tunnel Id of the Session object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the value signaled in the LSP ID.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

sleMplsTpTunnelCfgInfoSrcIdType		1.3.6.1.4.1.6296.101.16.14.1.1.1.4
This object is used to set the ietf or itut type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ietf(1), itut(2)

sleMplsTpTunnelCfgInfoSrcGId		1.3.6.1.4.1.6296.101.16.14.1.1.1.5
This Object is used to display the GlobalID of IETF
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

sleMplsTpTunnelCfgInfoSrcCc		1.3.6.1.4.1.6296.101.16.14.1.1.1.6
This Object is used to display the Source CC-ID of ITUT
Status: current	Access: read-only
OBJECT-TYPE
	MplsCcId

sleMplsTpTunnelCfgInfoSrcIcc		1.3.6.1.4.1.6296.101.16.14.1.1.1.7
This Object is used to set the Source ICC-ID of ITUT
Status: current	Access: read-only
OBJECT-TYPE
	MplsIccId

sleMplsTpTunnelCfgInfoSrcNodeId		1.3.6.1.4.1.6296.101.16.14.1.1.1.8
This Object is used to display the Source Node ID of IETF and ITUT
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

sleMplsTpTunnelCfgInfoDestIdType		1.3.6.1.4.1.6296.101.16.14.1.1.1.9
This object is used to set the ietf or itut type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ietf(1), itut(2)

sleMplsTpTunnelCfgInfoDestGId		1.3.6.1.4.1.6296.101.16.14.1.1.1.10
This Object is used to set the Destination GlobalID of IETF
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

sleMplsTpTunnelCfgInfoDestCc		1.3.6.1.4.1.6296.101.16.14.1.1.1.11
This Object is used to display the Destination CC-ID of ITUT
Status: current	Access: read-only
OBJECT-TYPE
	MplsCcId

sleMplsTpTunnelCfgInfoDestIcc		1.3.6.1.4.1.6296.101.16.14.1.1.1.12
This Object is used to set the Destination ICC-ID of ITUT
Status: current	Access: read-only
OBJECT-TYPE
	MplsIccId

sleMplsTpTunnelCfgInfoDestNodeId		1.3.6.1.4.1.6296.101.16.14.1.1.1.13
This Object is used to display the Destination Node ID of IETF and ITUT
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

sleMplsTpTunnelCfgInfoMode		1.3.6.1.4.1.6296.101.16.14.1.1.1.14
This object is used to set the Tunnel Mode
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), unidirectional(1), bidirectional(2), corouted(3), associate(4)

sleMplsTpTunnelCfgInfoFwdInLabel		1.3.6.1.4.1.6296.101.16.14.1.1.1.15
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575.. The default value 1048576 is invalid label
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgInfoFwdInIfIndex		1.3.6.1.4.1.6296.101.16.14.1.1.1.16
This object is used to set the Forward IN Interface index
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgInfoFwdOperation		1.3.6.1.4.1.6296.101.16.14.1.1.1.17
This object is used to set the Forward Ilm OPeration .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), push(1), pop(2), swap(3)

sleMplsTpTunnelCfgInfoFwdOutLabel		1.3.6.1.4.1.6296.101.16.14.1.1.1.18
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgInfoFwdOutIfIndex		1.3.6.1.4.1.6296.101.16.14.1.1.1.19
This object is used to set the Forward OUT Interface index
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgInfoFwdOutMac		1.3.6.1.4.1.6296.101.16.14.1.1.1.20
This object is used to display the Forward OUT MAC ADDRESS
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

sleMplsTpTunnelCfgInfoRevInLabel		1.3.6.1.4.1.6296.101.16.14.1.1.1.21
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgInfoRevInIfIndex		1.3.6.1.4.1.6296.101.16.14.1.1.1.22
This object is used to set the Reverse IN Interface index
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgInfoRevOperation		1.3.6.1.4.1.6296.101.16.14.1.1.1.23
This object is used to set the Reverse Ilm OPeration .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), push(1), pop(2), swap(3)

sleMplsTpTunnelCfgInfoRevOutLabel		1.3.6.1.4.1.6296.101.16.14.1.1.1.24
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgInfoRevOutIfIndex		1.3.6.1.4.1.6296.101.16.14.1.1.1.25
This object is used to set the Reverse OUT Interface index
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgInfoRevOutMac		1.3.6.1.4.1.6296.101.16.14.1.1.1.26
This object is used to display the Forward OUT MAC ADDRESS .
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

sleMplsTpTunnelCfgInfoState		1.3.6.1.4.1.6296.101.16.14.1.1.1.27
This object is to display status of the tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

sleMplsTpTunnelCfgInfoRole		1.3.6.1.4.1.6296.101.16.14.1.1.1.28
This object is to display Role of the tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	source(0), transist(1), destination(2)

sleMplsTpTunnelCfgInfoAssociateTnlName		1.3.6.1.4.1.6296.101.16.14.1.1.1.29
This object to display associate of reverse tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgInfoDescription		1.3.6.1.4.1.6296.101.16.14.1.1.1.30
Description.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgInfoHlspRole		1.3.6.1.4.1.6296.101.16.14.1.1.1.31
This object is used to set the Hlsp Tunnel. whether the tunnel is Server or client. server (1) :- To set the Server Tunnel client(2) :- To set the Client Tunnel .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	server(1), client(2)

sleMplsTpTunnelCfgInfoHlspServerTunnelName		1.3.6.1.4.1.6296.101.16.14.1.1.1.32
This object is used to set the server TunnelName, when sleMplsTpTunnelCfgControlHlspOption as a client .
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgInfoQosPolicyName		1.3.6.1.4.1.6296.101.16.14.1.1.1.33
This object is used to set the Qos Policy name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgControl		1.3.6.1.4.1.6296.101.16.14.1.2
OBJECT IDENTIFIER

sleMplsTpTunnelCfgControlRequest		1.3.6.1.4.1.6296.101.16.14.1.2.1
This object holds the possible read-write columns that can be modified in the Tunnel table. For each read-write column of Tunnel table, a Set Operation controlvalue is added in this object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	createMplsTpTunnelEntry(1), deleteMplsTpTunnelEntry(2), setMplsTpTunnelMode(3), setNhlfe(4), setIlmPop(5), setIlmSwap(6), setAssociateTunnel(7), unsetNhlfe(8), unsetIlmPop(9), unsetIlmSwap(10), unsetAssociateTunnel(11), setDescription(12), setHlspServerLsp(13), setHlspClientLsp(14), unsetHlspServerLsp(15), unsetHlspClientLsp(16), setTunnelQosPolicyName(17), unsetTunnelQosPolicyName(18)

sleMplsTpTunnelCfgControlStatus		1.3.6.1.4.1.6296.101.16.14.1.2.2
This object displays the status of the configuration done.
Status: current	Access: read-only
OBJECT-TYPE
	SleControlStatusType

sleMplsTpTunnelCfgControlTimer		1.3.6.1.4.1.6296.101.16.14.1.2.3
This object is based on the SLE style where a timer is configured for every control table.
Status: current	Access: read-write
OBJECT-TYPE
	Gauge32

sleMplsTpTunnelCfgControlTimeStamp		1.3.6.1.4.1.6296.101.16.14.1.2.4
This object specifies the time at which the configuration is done.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

sleMplsTpTunnelCfgControlReqResult		1.3.6.1.4.1.6296.101.16.14.1.2.5
The standard result of the SET operation is stored here.
Status: current	Access: read-only
OBJECT-TYPE
	SleControlRequestResultType

sleMplsTpTunnelCfgControlName		1.3.6.1.4.1.6296.101.16.14.1.2.6
The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to SlemplsTunnelName. Also see the description of ifName in RFC 2863.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..16)

sleMplsTpTunnelCfgControlId		1.3.6.1.4.1.6296.101.16.14.1.2.7
This object is used to set the tunnel Id .
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..65535

sleMplsTpTunnelCfgControlSrcIdType		1.3.6.1.4.1.6296.101.16.14.1.2.8
This object is used to set the ietf or itut type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ietf(1), itut(2)

sleMplsTpTunnelCfgControlSrcGId		1.3.6.1.4.1.6296.101.16.14.1.2.9
This object is used to set the source Global-Id for IETF .
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..4294967295

sleMplsTpTunnelCfgControlSrcCc		1.3.6.1.4.1.6296.101.16.14.1.2.10
This object is used to set the source CC-ID for ITUT.
Status: current	Access: read-write
OBJECT-TYPE
	MplsCcId

sleMplsTpTunnelCfgControlSrcIcc		1.3.6.1.4.1.6296.101.16.14.1.2.11
This object is used to set the Source ICC-ID for ITUT.
Status: current	Access: read-write
OBJECT-TYPE
	MplsIccId

sleMplsTpTunnelCfgControlSrcNodeId		1.3.6.1.4.1.6296.101.16.14.1.2.12
This object is used to set the Source Node-Id for IETF and ITUT
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sleMplsTpTunnelCfgControlDestIdType		1.3.6.1.4.1.6296.101.16.14.1.2.13
This object is used to set the ietf or itut type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ietf(1), itut(2)

sleMplsTpTunnelCfgControlDestGId		1.3.6.1.4.1.6296.101.16.14.1.2.14
This object is used to set the Destination Global-Id for IETF .
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1

sleMplsTpTunnelCfgControlDestCc		1.3.6.1.4.1.6296.101.16.14.1.2.15
This object is used to set the Destination CC-ID for ITUT.
Status: current	Access: read-write
OBJECT-TYPE
	MplsCcId

sleMplsTpTunnelCfgControlDestIcc		1.3.6.1.4.1.6296.101.16.14.1.2.16
This object is used to set the Destination ICC-ID for ITUT.
Status: current	Access: read-write
OBJECT-TYPE
	MplsIccId

sleMplsTpTunnelCfgControlDestNodeId		1.3.6.1.4.1.6296.101.16.14.1.2.17
This object is used to set the Destination NodeID for IETF and ITUT.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sleMplsTpTunnelCfgControlMode		1.3.6.1.4.1.6296.101.16.14.1.2.18
This object is used to set the Tunnel mode .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unidirectional(1), bidirectional(2)

sleMplsTpTunnelCfgControlPath		1.3.6.1.4.1.6296.101.16.14.1.2.19
This object is used to Set the forward path and reverse path tunnel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forwardPath(1), reversePath(2)

sleMplsTpTunnelCfgControlInLabel		1.3.6.1.4.1.6296.101.16.14.1.2.20
This object is used to set the Inlabel.
Status: current	Access: read-write
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgControlInInterface		1.3.6.1.4.1.6296.101.16.14.1.2.21
This object is used to set the Ininterface index.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgControlOperation		1.3.6.1.4.1.6296.101.16.14.1.2.22
This object is used to set the operation of Tuunel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	push(1), pop(2), swap(3)

sleMplsTpTunnelCfgControlOutLabel		1.3.6.1.4.1.6296.101.16.14.1.2.23
This object is used to set the outlabel.
Status: current	Access: read-write
OBJECT-TYPE
	MplsLabel

sleMplsTpTunnelCfgControlOutInterface		1.3.6.1.4.1.6296.101.16.14.1.2.24
This object is used to set the outerinterface index.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

sleMplsTpTunnelCfgControlOutMacAddress		1.3.6.1.4.1.6296.101.16.14.1.2.25
This object is used to Set the Out MacAddress .
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

sleMplsTpTunnelCfgControlAssociateTnlName		1.3.6.1.4.1.6296.101.16.14.1.2.26
This object is used to Associated Forward tunnel and reverse tunnel with reverse tunnel name .
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgControlDescription		1.3.6.1.4.1.6296.101.16.14.1.2.27
Description.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgControlHlspSeverTunnelName		1.3.6.1.4.1.6296.101.16.14.1.2.28
This object is used to set the server Tunnel name for associating server and client.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sleMplsTpTunnelCfgControlQosPolicyName		1.3.6.1.4.1.6296.101.16.14.1.2.29
This object is used to set the Qos Policy name.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING