SUB10SYSTEMS-MIB

File: SUB10SYSTEMS-MIB.mib (376434 bytes)

Imported modules

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Unsigned32	Integer32	Counter32
Counter64	enterprises	TEXTUAL-CONVENTION
DisplayString	DateAndTime	RowStatus
MODULE-COMPLIANCE	NOTIFICATION-GROUP	OBJECT-GROUP

Defined Types

Sub10EthInterfaceIndex
A unique value, greater than zero, for each ethernet type interface.
TEXTUAL-CONVENTION
	Unsigned32	1..2

Sub10EntryStatus
A general configuration type to indicate if a table row is in use or not in use. This differs from RowStatus which is a settable object used to create the existence of a row in a configurable table. Sub10EntryStatus is intended to be read-only and is set internally by the Agent when a table row is populated with valid data.
TEXTUAL-CONVENTION
	INTEGER	entryInUse(1), entryNotInUse(2)

Sub10State
A general configuration type to indicate enabled or disabled.
TEXTUAL-CONVENTION
	INTEGER	stateDisabled(0), stateEnabled(1)

Sub10UnitType
Sub10Systems unit type.
TEXTUAL-CONVENTION
	INTEGER	baseband100A(0), baseband100B(1), baseband1000A(2), baseband1000B(3), v100ROWA(4), v100ROWB(5), v100FCCA(6), v100FCCB(7), v1000ROWA(8), v1000ROWB(9), v1000FCCA(10), v1000FCCB2(11), e1000ROWA(12), e1000ROWB(13), e1000FCCA(14), e1000FCCB(15)

Sub10TerminalType
Sub10Systems terminal type. A link must have an 'A' end terminal and a 'B' end terminal.
TEXTUAL-CONVENTION
	INTEGER	terminalA(0), terminalB(1)

Sub10Availability
Availability selects RSSI thresholds for modulation changes.
TEXTUAL-CONVENTION
	INTEGER	availabilityHigh(0), availabilityMedium(1), availabilityLow(2)

Sub10AlignmentMode
Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). The alignment mode is managed using sub10RadioMgmtAlignmentMode.
TEXTUAL-CONVENTION
	INTEGER	modeNormal(0), modeAlignment(1)

Sub10AlignmentModeLock
If locked, the unit will not go into alignment mode when the alignment cap is removed.
TEXTUAL-CONVENTION
	INTEGER	modeUnlocked(0), modeLocked(1)

Sub10OperStatus
The status of the ethernet link, this maps directly to ifOperStatus.
TEXTUAL-CONVENTION
	INTEGER	opStatusUp(1), opStatusDown(2), opStatusTesting(3), opStatusUnknown(4), opStatusDormant(5), opStatusNotPresent(6), opStatusLowerLayerDown(7)

Sub10Duplex
The operation of a duplex link link
TEXTUAL-CONVENTION
	INTEGER	halfDuplex(1), fullDuplex(2), unknownDuplex(3)

Sub10MDIType
The operation of a duplex link link. The setting of 'auto' is used only for configuration puprposes.
TEXTUAL-CONVENTION
	INTEGER	mdi(1), mdix(2), mdiUnknown(3)

Sub10RadioLinkState
The status of the radio link
TEXTUAL-CONVENTION
	INTEGER	radioLinkStateDown(0), radioLinkStateUp(1), radioLinkStateUnknown(2)

Sub10AlarmName
Name convention for all notification types.
TEXTUAL-CONVENTION
	OCTET STRING	Size(1..32)

Sub10MacAddress
MAC Address in readable string format.
TEXTUAL-CONVENTION
	OCTET STRING	Size(11..17)

Sub10AlarmState
Alarm state.
TEXTUAL-CONVENTION
	INTEGER	cleared(1), raised(2), stateUnknown(3)

Sub10DateTime
The generic Sub10 format for a date time string. Format is YYYY-MM-DD HH:MM:SS e.g. 2014-05-26 13:30:15
TEXTUAL-CONVENTION
	OCTET STRING	Size(19..19)

Sub10AlarmIndex
The MIB index used to define the range of indexing and size of the Alarm tables sub10UnitLclAlarmStateTable and sub10UnitMgmtAlarmTable.
TEXTUAL-CONVENTION
	Unsigned32	1..128

Sub10MeasuredObject
A MIB object that may be measured by Alarm Management or any other sub-system.
TEXTUAL-CONVENTION
	INTEGER	sub10UnitLclMWUTemperature(1), sub10RadioLclRxPower(2), sub10RadioLclVectErr(3), sub10RadioLclLnkLoss(4), sub10RadioLclTxPower(5), sub10RadioMgmtTxRxFreq(6), sub10RadioMgmtAPCMode(7), sub10RadioMgmtModulationMode(8), sub10RadioMgmtAlignmentMode(9), sub10RadioLclLinkStatus(10), sub10RadioLclRxModulationMode(11), sub10RadioLclTxModulationMode(12), sub10RadioStatsCurrTxPowerMin(20), sub10RadioStatsCurrTxPowerMax(21), sub10RadioStatsCurrTxPowerAvg(22), sub10RadioStatsCurrRxPowerMin(23), sub10RadioStatsCurrRxPowerMax(24), sub10RadioStatsCurrRxPowerAvg(25), sub10RadioStatsCurrVectErrMin(26), sub10RadioStatsCurrVectErrMax(27), sub10RadioStatsCurrVectErrAvg(28), sub10RadioStatsCurrLnkLossMin(29), sub10RadioStatsCurrLnkLossMax(30), sub10RadioStatsCurrLnkLossAvg(31), sub10RadioStatsCurrMWUTempMin(32), sub10RadioStatsCurrMWUTempMax(33), sub10RadioStatsCurrMWUTempAvg(34), sub10RadioStatsCurrAFERMin(35), sub10RadioStatsCurrAFERMax(36), sub10RadioStatsCurrAFERAvg(37), sub10RadioStats1mHistTxPowerMin(50), sub10RadioStats1mHistTxPowerMax(51), sub10RadioStats1mHistTxPowerAvg(52), sub10RadioStats1mHistRxPowerMin(53), sub10RadioStats1mHistRxPowerMax(54), sub10RadioStats1mHistRxPowerAvg(55), sub10RadioStats1mHistVectErrMin(56), sub10RadioStats1mHistVectErrMax(57), sub10RadioStats1mHistVectErrAvg(58), sub10RadioStats1mHistLnkLossMin(59), sub10RadioStats1mHistLnkLossMax(60), sub10RadioStats1mHistLnkLossAvg(61), sub10RadioStats1mHistMWUTempMin(62), sub10RadioStats1mHistMWUTempMax(63), sub10RadioStats1mHistMWUTempAvg(64), sub10RadioStats1mHistAFERMin(65), sub10RadioStats1mHistAFERMax(66), sub10RadioStats1mHistAFERAvg(67), sub10RadioStats1mHistRxPkts(68), sub10RadioStats1mHistTxPkts(69), sub10RadioStats1mHistRxMgmtPkts(70), sub10RadioStats1mHistTxMgmtPkts(71), sub10RadioStats1mHistRxBadFrms(72), sub10RadioStats1mHistQPSKTo8PSK(73), sub10RadioStats1mHist8PSKToQPSK(74), sub10RadioStats1mHistRxQPSK(75), sub10RadioStats1mHistRx8PSK(76), sub10RadioStats1mHistTxQPSK(77), sub10RadioStats1mHistTx8PSK(78), sub10RadioStats15mHistTxPowerMin(90), sub10RadioStats15mHistTxPowerMax(91), sub10RadioStats15mHistTxPowerAvg(92), sub10RadioStats15mHistRxPowerMin(93), sub10RadioStats15mHistRxPowerMax(94), sub10RadioStats15mHistRxPowerAvg(95), sub10RadioStats15mHistVectErrMin(96), sub10RadioStats15mHistVectErrMax(97), sub10RadioStats15mHistVectErrAvg(98), sub10RadioStats15mHistLnkLossMin(99), sub10RadioStats15mHistLnkLossMax(100), sub10RadioStats15mHistLnkLossAvg(101), sub10RadioStats15mHistMWUTempMin(102), sub10RadioStats15mHistMWUTempMax(103), sub10RadioStats15mHistMWUTempAvg(104), sub10RadioStats15mHistAFERMin(105), sub10RadioStats15mHistAFERMax(106), sub10RadioStats15mHistAFERAvg(107), sub10RadioStats15mHistRxPkts(108), sub10RadioStats15mHistTxPkts(109), sub10RadioStats15mHistRxMgmtPkts(110), sub10RadioStats15mHistTxMgmtPkts(111), sub10RadioStats15mHistRxBadFrms(112), sub10RadioStats15mHistQPSKTo8PSK(113), sub10RadioStats15mHist8PSKToQPSK(114), sub10RadioStats15mHistRxQPSK(115), sub10RadioStats15mHistRx8PSK(116), sub10RadioStats15mHistTxQPSK(117), sub10RadioStats15mHistTx8PSK(118), sub10EthStatsCurrRxMbps(140), sub10EthStatsCurrTxMbps(141), sub10EthStatsCurrRxMbpsMin(142), sub10EthStatsCurrRxMbpsMax(143), sub10EthStatsCurrRxMbpsAvg(144), sub10EthStatsCurrTxMbpsMin(145), sub10EthStatsCurrTxMbpsMax(146), sub10EthStatsCurrTxMbpsAvg(147), sub10EthStats1mHistRxOctets(160), sub10EthStats1mHistRxGoodFrms(161), sub10EthStats1mHistRxBcastFrms(162), sub10EthStats1mHistRxMcastFrms(163), sub10EthStats1mHistRxPauseFrms(164), sub10EthStats1mHistRxCRCErrs(165), sub10EthStats1mHistRxAlignErrs(166), sub10EthStats1mHistRxOversized(167), sub10EthStats1mHistRxJabberFrms(168), sub10EthStats1mHistRxUndersized(169), sub10EthStats1mHistRxFragments(170), sub10EthStats1mHistRxSOFOvrns(171), sub10EthStats1mHistTxOctets(172), sub10EthStats1mHistTxGoodFrms(173), sub10EthStats1mHistTxBcastFrms(174), sub10EthStats1mHistTxMcastFrms(175), sub10EthStats1mHistTxPauseFrms(176), sub10EthStats1mHistTxDeferred(177), sub10EthStats1mHistTxCollsn(178), sub10EthStats1mHistTxSnglCollsn(179), sub10EthStats1mHistTxMlplCollsn(180), sub10EthStats1mHistTxExsvCollsn(181), sub10EthStats1mHistTxLtCollsn(182), sub10EthStats1mHistTxCSenseErrs(183), sub10EthStats1mHistPkts64Octets(184), sub10EthStats1mHistPkts65T127(185), sub10EthStats1mHistPkts128T255(186), sub10EthStats1mHistPkts256T511(187), sub10EthStats1mHistPkts512T1023(188), sub10EthStats1mHistPkts1024TMax(189), sub10EthStats1mHistRxMbpsMin(190), sub10EthStats1mHistRxMbpsMax(191), sub10EthStats1mHistRxMbpsAvg(192), sub10EthStats1mHistTxMbpsMin(193), sub10EthStats1mHistTxMbpsMax(194), sub10EthStats1mHistTxMbpsAvg(195), sub10EthStats15mHistRxOctets(210), sub10EthStats15mHistRxGoodFrms(211), sub10EthStats15mHistRxBcastFrms(212), sub10EthStats15mHistRxMcastFrms(213), sub10EthStats15mHistRxPauseFrms(214), sub10EthStats15mHistRxCRCErrs(215), sub10EthStats15mHistRxAlignErrs(216), sub10EthStats15mHistRxOversized(217), sub10EthStats15mHistRxJabberFrms(218), sub10EthStats15mHistRxUndersized(219), sub10EthStats15mHistRxFragments(220), sub10EthStats15mHistRxSOFOvrns(221), sub10EthStats15mHistTxOctets(222), sub10EthStats15mHistTxGoodFrms(223), sub10EthStats15mHistTxBcastFrms(224), sub10EthStats15mHistTxMcastFrms(225), sub10EthStats15mHistTxPauseFrms(226), sub10EthStats15mHistTxDeferred(227), sub10EthStats15mHistTxCollsn(228), sub10EthStats15mHistTxSnglCollsn(229), sub10EthStats15mHistTxMlplCollsn(230), sub10EthStats15mHistTxExsvCollsn(231), sub10EthStats15mHistTxLtCollsn(232), sub10EthStats15mHistTxCSenseErrs(233), sub10EthStats15mHistPkts64Octets(234), sub10EthStats15mHistPkts65T127(235), sub10EthStats15mHistPkts128T255(236), sub10EthStats15mHistPkts256T511(237), sub10EthStats15mHistPkts512T1023(238), sub10EthStats15mHistPkts1024TMax(239), sub10EthStats15mHistRxMbpsMin(240), sub10EthStats15mHistRxMbpsMax(241), sub10EthStats15mHistRxMbpsAvg(242), sub10EthStats15mHistTxMbpsMin(243), sub10EthStats15mHistTxMbpsMax(244), sub10EthStats15mHistTxMbpsAvg(245), sub10RadioStats1dHistTxPowerMin(260), sub10RadioStats1dHistTxPowerMax(261), sub10RadioStats1dHistTxPowerAvg(262), sub10RadioStats1dHistRxPowerMin(263), sub10RadioStats1dHistRxPowerMax(264), sub10RadioStats1dHistRxPowerAvg(265), sub10RadioStats1dHistVectErrMin(266), sub10RadioStats1dHistVectErrMax(267), sub10RadioStats1dHistVectErrAvg(268), sub10RadioStats1dHistLnkLossMin(269), sub10RadioStats1dHistLnkLossMax(270), sub10RadioStats1dHistLnkLossAvg(271), sub10RadioStats1dHistMWUTempMin(272), sub10RadioStats1dHistMWUTempMax(273), sub10RadioStats1dHistMWUTempAvg(274), sub10RadioStats1dHistAFERMin(275), sub10RadioStats1dHistAFERMax(276), sub10RadioStats1dHistAFERAvg(277), sub10RadioStats1dHistRxPkts(278), sub10RadioStats1dHistTxPkts(279), sub10RadioStats1dHistRxMgmtPkts(280), sub10RadioStats1dHistTxMgmtPkts(281), sub10RadioStats1dHistRxBadFrms(282), sub10RadioStats1dHistQPSKTo8PSK(283), sub10RadioStats1dHist8PSKToQPSK(284), sub10RadioStats1dHistRxQPSK(285), sub10RadioStats1dHistRx8PSK(286), sub10RadioStats1dHistTxQPSK(287), sub10RadioStats1dHistTx8PSK(288), sub10EthStats1dHistRxOctets(300), sub10EthStats1dHistRxGoodFrms(301), sub10EthStats1dHistRxBcastFrms(302), sub10EthStats1dHistRxMcastFrms(303), sub10EthStats1dHistRxPauseFrms(304), sub10EthStats1dHistRxCRCErrs(305), sub10EthStats1dHistRxAlignErrs(306), sub10EthStats1dHistRxOversized(307), sub10EthStats1dHistRxJabberFrms(308), sub10EthStats1dHistRxUndersized(309), sub10EthStats1dHistRxFragments(310), sub10EthStats1dHistRxSOFOvrns(311), sub10EthStats1dHistTxOctets(312), sub10EthStats1dHistTxGoodFrms(313), sub10EthStats1dHistTxBcastFrms(314), sub10EthStats1dHistTxMcastFrms(315), sub10EthStats1dHistTxPauseFrms(316), sub10EthStats1dHistTxDeferred(317), sub10EthStats1dHistTxCollsn(318), sub10EthStats1dHistTxSnglCollsn(319), sub10EthStats1dHistTxMlplCollsn(320), sub10EthStats1dHistTxExsvCollsn(321), sub10EthStats1dHistTxLtCollsn(322), sub10EthStats1dHistTxCSenseErrs(323), sub10EthStats1dHistPkts64Octets(324), sub10EthStats1dHistPkts65T127(325), sub10EthStats1dHistPkts128T255(326), sub10EthStats1dHistPkts256T511(327), sub10EthStats1dHistPkts512T1023(328), sub10EthStats1dHistPkts1024TMax(329), sub10EthStats1dHistRxMbpsMin(330), sub10EthStats1dHistRxMbpsMax(331), sub10EthStats1dHistRxMbpsAvg(332), sub10EthStats1dHistTxMbpsMin(333), sub10EthStats1dHistTxMbpsMax(334), sub10EthStats1dHistTxMbpsAvg(335)

Sub10AlarmSeverity
Severity for notifications of type alarm
TEXTUAL-CONVENTION
	INTEGER	critical(1), major(2), minor(3), warning(4)

Sub10AlarmOperation
The operation that is used to compare a measured value with a configured alarm threshold which controls the raising and clearing of alarms.
TEXTUAL-CONVENTION
	INTEGER	lessThan(1), greaterThan(2), lessThanOrEqual(3), greaterThanOrEqual(4), equal(5), notEqual(6)

Sub10AlarmType
The type of the alarm and defines the type of notification (trap) used to inform management entities.
TEXTUAL-CONVENTION
	INTEGER	sub10UnitAlarm(1), sub10EthernetAlarm(2), sub10RadioAlarm(3)

Sub10NTPSyncStatus
The indication that the systems clock is synchronised with the NTP server.
TEXTUAL-CONVENTION
	INTEGER	ntpOutOfSync(0), ntpInSync(1)

Sub10VlanId
A VLAN Id (12 bits in the TCF part of an ethernet frame).
TEXTUAL-CONVENTION
	Unsigned32	0..4095

Sub10VlanTagAction
Used in Vlan Mgmt to support Vlan tag manipulaton on the Ethernet interface.
TEXTUAL-CONVENTION
	INTEGER	tagActionNone(0), untag(1), tag(2), drop(3)

Sub10VlanPriority
A VLAN Priority or PCP bits (3 bits in the TCF part of an ethernet frame). The priority PCP bits are based on 802.1p where 0 is the lowest and 7 is the highest. Priority Acronym Traffic Types 0 BK Background 1 BE Best Effort 2 EE Excellent Effort 3 CA Critical Applications 4 VI Video, 100 ms latency and jitter 5 VO Voice, 10 ms latency and jitter 6 IC Internetwork Control 7 NC Network Control.
TEXTUAL-CONVENTION
	Unsigned32	0..7

Sub10QoSQueue
Identifies the QoS queue number for up to 8 queues.
TEXTUAL-CONVENTION
	Unsigned32	0..7

Sub10TxPowerLimit
The settings for Transmit Power limit on the Radio interface. A value of txPowerLimitNone means the TxPower is not limited by the radio.
TEXTUAL-CONVENTION
	INTEGER	txPowerLimitNone(0), txPowerLimitMinus3(1), txPowerLimitMinus6(2), txPowerLimitMinus9(3), txPowerLimitMinus12(4), txPowerLimitMinus15(5)

Sub10RadioDataRate
The maximum data rate of the Airside interface.
TEXTUAL-CONVENTION
	INTEGER	radioDataRate1000(0), radioDataRate700(1), radioDataRate500(2), radioDataRate300(3), radioDataRate100(4)

Sub10UserGroup
The user group types. A user is assigned to a group where each group has specific access privileges.
TEXTUAL-CONVENTION
	INTEGER	operation(1), administration(2), maintenance(3), engineer(4)

Sub10Snmpv3SecurityLevel
The SNMPv3 security level assigned to a group of SNMPv3 users.
TEXTUAL-CONVENTION
	INTEGER	noAuthNoPriv(1), authNoPriv(2), authPriv(3)

Sub10Snmpv3AuthProtocol
The SNMPv3 authentication protocol assigned to a group of SNMPv3 users.
TEXTUAL-CONVENTION
	INTEGER	noAuth(1), md5(2), sha1(3)

Sub10Snmpv3PrivProtocol
The SNMPv3 privacy protocol assigned to a group of SNMPv3 users.
TEXTUAL-CONVENTION
	INTEGER	noPriv(1), des(2), aes(3)

Sub10MWUType
The type of MWU.
TEXTUAL-CONVENTION
	INTEGER	mwuTypeNone(0), mwuTypeVBand(1), mwuTypeEBand(2)

Sub10FirmwareBank
Identifies the firmware bank number.
TEXTUAL-CONVENTION
	Unsigned32	1..3

Sub10StatsGroup
The type of stats.
TEXTUAL-CONVENTION
	INTEGER	statsGroupNone(1), statsGroupAll(2), statsGroupRadioCurr(3), statsGroupRadio1s(4), statsGroupRadio1m(5), statsGroupRadio15m(6), statsGroupRadio1d(7), statsGroupEthernetCurr(8), statsGroupEthernet1s(9), statsGroupEthernet1m(10), statsGroupEthernet15m(11), statsGroupEthernet1d(12), statsGroupRadioCurr60s(13)

Sub10ThroughputMbps
Throughput in Mbps (MegaBits per second).
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..32)

Sub10ModulationMode
Radio Modulation Mode.
TEXTUAL-CONVENTION
	INTEGER	modebpsk(0), modeqpsk(1), mode8psk(2)

Sub10UnitLclAlarmStateEntry
SEQUENCE
	sub10UnitLclAlarmStateIndex	Sub10AlarmIndex
	sub10UnitLclAlarmState	Sub10AlarmState
	sub10UnitLclAlarmStateTime	Sub10DateTime

Sub10UnitMgmtUserEntry
SEQUENCE
	sub10UnitMgmtUserIndex	Unsigned32
	sub10UnitMgmtUserRowStatus	RowStatus
	sub10UnitMgmtUserName	OCTET STRING
	sub10UnitMgmtUserGroup	Sub10UserGroup
	sub10UnitMgmtUserPassword	OCTET STRING
	sub10UnitMgmtUserPasswordVerify	OCTET STRING

Sub10UnitMgmtAlarmEntry
SEQUENCE
	sub10UnitMgmtAlarmIndex	Sub10AlarmIndex
	sub10UnitMgmtAlarmRowStatus	RowStatus
	sub10UnitMgmtAlarmName	Sub10AlarmName
	sub10UnitMgmtAlarmSeverity	Sub10AlarmSeverity
	sub10UnitMgmtAlarmMeasObject	Sub10MeasuredObject
	sub10UnitMgmtAlarmMonitorIntvl	Unsigned32
	sub10UnitMgmtAlarmRaiseOper	Sub10AlarmOperation
	sub10UnitMgmtAlarmRaiseThresh	OCTET STRING
	sub10UnitMgmtAlarmClearOper	Sub10AlarmOperation
	sub10UnitMgmtAlarmClearThresh	OCTET STRING
	sub10UnitMgmtAlarmRaiseIntvls	Unsigned32
	sub10UnitMgmtAlarmClearIntvls	Unsigned32
	sub10UnitMgmtAlarmType	Sub10AlarmType
	sub10UnitMgmtAlarmSmtpAddress	OCTET STRING
	sub10UnitMgmtAlarmToSyslog	Sub10State
	sub10UnitMgmtAlarmEnabled	Sub10State
	sub10UnitMgmtAlarmMeasObjectVal	DisplayString
	sub10UnitMgmtAlarmToSNMP	Sub10State
	sub10UnitMgmtAlarmMeasObjIndex	Unsigned32

Sub10UnitMgmtSnmpTrpDstEntry
SEQUENCE
	sub10UnitMgmtSnmpTrpDstIndex	Unsigned32
	sub10UnitMgmtSnmpTrpDstRowStatus	RowStatus
	sub10UnitMgmtSnmpTrpDstIpAddr	OCTET STRING
	sub10UnitMgmtSnmpTrpDstCommunity	OCTET STRING

Sub10UnitMgmtSnmpUserEntry
SEQUENCE
	sub10UnitMgmtSnmpUserIndex	Unsigned32
	sub10UnitMgmtSnmpUserRowStatus	RowStatus
	sub10UnitMgmtSnmpUserName	OCTET STRING
	sub10UnitMgmtSnmpUserGroup	Sub10UserGroup
	sub10UnitMgmtSnmpUserAuthPwd	OCTET STRING
	sub10UnitMgmtSnmpUserAuthPwdChk	OCTET STRING
	sub10UnitMgmtSnmpUserPrivPwd	OCTET STRING
	sub10UnitMgmtSnmpUserPrivPwdChk	OCTET STRING

Sub10UnitMgmtSnmpAccessEntry
SEQUENCE
	sub10UnitMgmtSnmpAccessIndex	Unsigned32
	sub10UnitMgmtSnmpAccessRowStatus	RowStatus
	sub10UnitMgmtSnmpAccessName	OCTET STRING
	sub10UnitMgmtSnmpAccessIpAddr	OCTET STRING

Sub10UnitMgmtSnmpTargetEntry
SEQUENCE
	sub10UnitMgmtSnmpTargetIndex	Unsigned32
	sub10UnitMgmtSnmpTargetRowStatus	RowStatus
	sub10UnitMgmtSnmpTargetName	OCTET STRING
	sub10UnitMgmtSnmpTargetIpAddr	OCTET STRING
	sub10UnitMgmtSnmpTargetUserName	OCTET STRING

Sub10UnitMgmtFirmwareBankEntry
SEQUENCE
	sub10UnitMgmtFirmwareBankIndex	Sub10FirmwareBank
	sub10UnitMgmtFirmwareBankVersion	OCTET STRING
	sub10UnitMgmtFirmwareBankImage	OCTET STRING

Sub10UnitMgmtDNSEntry
SEQUENCE
	sub10UnitMgmtDNSIndex	Unsigned32
	sub10UnitMgmtDNServer	OCTET STRING

Sub10EthLclStatusEntry
SEQUENCE
	sub10EthLclLinkStatus	Sub10OperStatus
	sub10EthLclMacAddress	Sub10MacAddress
	sub10EthLclSpeed	Unsigned32
	sub10EthLclDuplex	Sub10Duplex
	sub10EthLclMDI	Sub10MDIType
	sub10EthIfIndex	Sub10EthInterfaceIndex

Sub10EthRmtStatusEntry
SEQUENCE
	sub10EthRmtLinkStatus	Sub10OperStatus
	sub10EthRmtMacAddress	Sub10MacAddress
	sub10EthRmtSpeed	Unsigned32
	sub10EthRmtDuplex	Sub10Duplex
	sub10EthRmtMDI	Sub10MDIType

Sub10EthMgmtPhyEntry
SEQUENCE
	sub10EthMgmtPhyAutoNeg	Sub10State
	sub10EthMgmtPhySpeed	Unsigned32
	sub10EthMgmtPhyDuplex	Sub10Duplex
	sub10EthMgmtPhyMDI	Sub10MDIType

Sub10EthMgmtVlanAllowedEntry
SEQUENCE
	sub10EthMgmtVlanAllowedIndex	Unsigned32
	sub10EthMgmtVlanAllowedRowStatus	RowStatus
	sub10EthMgmtVlanAllowedId	Sub10VlanId

Sub10EthMgmtQoSQEntry
SEQUENCE
	sub10EthMgmtQoSQIndex	Unsigned32
	sub10EthMgmtQoSQSchedulingType	INTEGER
	sub10EthMgmtQoSQDWRRWeight	Unsigned32
	sub10EthMgmtQoSQCongestionPolicy	INTEGER
	sub10EthMgmtQoSQSizeMax	Unsigned32
	sub10EthMgmtQoSQLen	Unsigned32

Sub10EthMgmtQoSVlanEntry
SEQUENCE
	sub10EthMgmtQoSVlanIndex	Unsigned32
	sub10EthMgmtQoSVlanId	Sub10VlanId
	sub10EthMgmtQoSVlanQueue	Sub10QoSQueue

Sub10EthMgmtQoSPCPEntry
SEQUENCE
	sub10EthMgmtQoSPCPIndex	Unsigned32
	sub10EthMgmtQoSPCPQueue	Sub10QoSQueue

Sub10EthMgmtQoSDSCPEntry
SEQUENCE
	sub10EthMgmtQoSDSCPIndex	Unsigned32
	sub10EthMgmtQoSDSCPMarking	Unsigned32
	sub10EthMgmtQoSDSCPQueue	Sub10QoSQueue

Sub10EthMgmtQoSMPLSEntry
SEQUENCE
	sub10EthMgmtQoSMPLSIndex	Unsigned32
	sub10EthMgmtQoSMPLSTrafficClass	Unsigned32
	sub10EthMgmtQoSMPLSQueue	Sub10QoSQueue

Sub10EthMgmtStatsActiveEntry
SEQUENCE
	sub10EthMgmtStatsActiveIndex	Unsigned32
	sub10EthMgmtStatsActiveName	OCTET STRING
	sub10EthMgmtStatsActiveState	Sub10State

Sub10EthernetStatsCurrEntry
SEQUENCE
	sub10EthStatsCurrRxOctets	Counter32
	sub10EthStatsCurrRxGoodFrms	Counter32
	sub10EthStatsCurrRxBcastFrms	Counter32
	sub10EthStatsCurrRxMcastFrms	Counter32
	sub10EthStatsCurrRxPauseFrms	Counter32
	sub10EthStatsCurrRxCRCErrs	Counter32
	sub10EthStatsCurrRxAlignErrs	Counter32
	sub10EthStatsCurrRxOversized	Counter32
	sub10EthStatsCurrRxJabberFrms	Counter32
	sub10EthStatsCurrRxUndersized	Counter32
	sub10EthStatsCurrRxFragments	Counter32
	sub10EthStatsCurrRxSOFOvrns	Counter32
	sub10EthStatsCurrTxOctets	Counter32
	sub10EthStatsCurrTxGoodFrms	Counter32
	sub10EthStatsCurrTxBcastFrms	Counter32
	sub10EthStatsCurrTxMcastFrms	Counter32
	sub10EthStatsCurrTxPauseFrms	Counter32
	sub10EthStatsCurrTxDeferred	Counter32
	sub10EthStatsCurrTxCollsn	Counter32
	sub10EthStatsCurrTxSnglCollsn	Counter32
	sub10EthStatsCurrTxMlplCollsn	Counter32
	sub10EthStatsCurrTxExsvCollsn	Counter32
	sub10EthStatsCurrTxLtCollsn	Counter32
	sub10EthStatsCurrTxCSenseErrs	Counter32
	sub10EthStatsCurrPkts64Octets	Counter32
	sub10EthStatsCurrPkts65T127	Counter32
	sub10EthStatsCurrPkts128T255	Counter32
	sub10EthStatsCurrPkts256T511	Counter32
	sub10EthStatsCurrPkts512T1023	Counter32
	sub10EthStatsCurrPkts1024TMax	Counter32
	sub10EthStatsCurrRxMbps	Sub10ThroughputMbps
	sub10EthStatsCurrTxMbps	Sub10ThroughputMbps
	sub10EthStatsCurrRxMbpsMin	Sub10ThroughputMbps
	sub10EthStatsCurrRxMbpsMax	Sub10ThroughputMbps
	sub10EthStatsCurrRxMbpsAvg	Sub10ThroughputMbps
	sub10EthStatsCurrTxMbpsMin	Sub10ThroughputMbps
	sub10EthStatsCurrTxMbpsMax	Sub10ThroughputMbps
	sub10EthStatsCurrTxMbpsAvg	Sub10ThroughputMbps
	sub10EthStatsCurrRmtRxMbpsAvg	Sub10ThroughputMbps
	sub10EthStatsCurrRmtTxMbpsAvg	Sub10ThroughputMbps

Sub10EthStats15mHistEntry
SEQUENCE
	sub10EthStats15mHistIntvl	Unsigned32
	sub10EthStats15mHistTime	Sub10DateTime
	sub10EthStats15mHistRxOctets	Counter64
	sub10EthStats15mHistRxGoodFrms	Counter64
	sub10EthStats15mHistRxBcastFrms	Counter64
	sub10EthStats15mHistRxMcastFrms	Counter64
	sub10EthStats15mHistRxPauseFrms	Counter64
	sub10EthStats15mHistRxCRCErrs	Counter64
	sub10EthStats15mHistRxAlignErrs	Counter64
	sub10EthStats15mHistRxOversized	Counter64
	sub10EthStats15mHistRxJabberFrms	Counter64
	sub10EthStats15mHistRxUndersized	Counter64
	sub10EthStats15mHistRxFragments	Counter64
	sub10EthStats15mHistRxSOFOvrns	Counter64
	sub10EthStats15mHistTxOctets	Counter64
	sub10EthStats15mHistTxGoodFrms	Counter64
	sub10EthStats15mHistTxBcastFrms	Counter64
	sub10EthStats15mHistTxMcastFrms	Counter64
	sub10EthStats15mHistTxPauseFrms	Counter64
	sub10EthStats15mHistTxDeferred	Counter64
	sub10EthStats15mHistTxCollsn	Counter64
	sub10EthStats15mHistTxSnglCollsn	Counter64
	sub10EthStats15mHistTxMlplCollsn	Counter64
	sub10EthStats15mHistTxExsvCollsn	Counter64
	sub10EthStats15mHistTxLtCollsn	Counter64
	sub10EthStats15mHistTxCSenseErrs	Counter64
	sub10EthStats15mHistPkts64Octets	Counter64
	sub10EthStats15mHistPkts65T127	Counter64
	sub10EthStats15mHistPkts128T255	Counter64
	sub10EthStats15mHistPkts256T511	Counter64
	sub10EthStats15mHistPkts512T1023	Counter64
	sub10EthStats15mHistPkts1024TMax	Counter64
	sub10EthStats15mHistRxMbpsMin	Sub10ThroughputMbps
	sub10EthStats15mHistRxMbpsMax	Sub10ThroughputMbps
	sub10EthStats15mHistRxMbpsAvg	Sub10ThroughputMbps
	sub10EthStats15mHistTxMbpsMin	Sub10ThroughputMbps
	sub10EthStats15mHistTxMbpsMax	Sub10ThroughputMbps
	sub10EthStats15mHistTxMbpsAvg	Sub10ThroughputMbps

Sub10EthStats1dHistEntry
SEQUENCE
	sub10EthStats1dHistIntvl	Unsigned32
	sub10EthStats1dHistTime	Sub10DateTime
	sub10EthStats1dHistRxOctets	Counter64
	sub10EthStats1dHistRxGoodFrms	Counter64
	sub10EthStats1dHistRxBcastFrms	Counter64
	sub10EthStats1dHistRxMcastFrms	Counter64
	sub10EthStats1dHistRxPauseFrms	Counter64
	sub10EthStats1dHistRxCRCErrs	Counter64
	sub10EthStats1dHistRxAlignErrs	Counter64
	sub10EthStats1dHistRxOversized	Counter64
	sub10EthStats1dHistRxJabberFrms	Counter64
	sub10EthStats1dHistRxUndersized	Counter64
	sub10EthStats1dHistRxFragments	Counter64
	sub10EthStats1dHistRxSOFOvrns	Counter64
	sub10EthStats1dHistTxOctets	Counter64
	sub10EthStats1dHistTxGoodFrms	Counter64
	sub10EthStats1dHistTxBcastFrms	Counter64
	sub10EthStats1dHistTxMcastFrms	Counter64
	sub10EthStats1dHistTxPauseFrms	Counter64
	sub10EthStats1dHistTxDeferred	Counter64
	sub10EthStats1dHistTxCollsn	Counter64
	sub10EthStats1dHistTxSnglCollsn	Counter64
	sub10EthStats1dHistTxMlplCollsn	Counter64
	sub10EthStats1dHistTxExsvCollsn	Counter64
	sub10EthStats1dHistTxLtCollsn	Counter64
	sub10EthStats1dHistTxCSenseErrs	Counter64
	sub10EthStats1dHistPkts64Octets	Counter64
	sub10EthStats1dHistPkts65T127	Counter64
	sub10EthStats1dHistPkts128T255	Counter64
	sub10EthStats1dHistPkts256T511	Counter64
	sub10EthStats1dHistPkts512T1023	Counter64
	sub10EthStats1dHistPkts1024TMax	Counter64
	sub10EthStats1dHistRxMbpsMin	Sub10ThroughputMbps
	sub10EthStats1dHistRxMbpsMax	Sub10ThroughputMbps
	sub10EthStats1dHistRxMbpsAvg	Sub10ThroughputMbps
	sub10EthStats1dHistTxMbpsMin	Sub10ThroughputMbps
	sub10EthStats1dHistTxMbpsMax	Sub10ThroughputMbps
	sub10EthStats1dHistTxMbpsAvg	Sub10ThroughputMbps

Sub10RadioMgmtStatsActiveEntry
SEQUENCE
	sub10RadioMgmtStatsActiveIndex	Unsigned32
	sub10RadioMgmtStatsActiveName	OCTET STRING
	sub10RadioMgmtStatsActiveState	Sub10State

Sub10RadioStats1mHistEntry
SEQUENCE
	sub10RadioStats1mHistIntvl	Unsigned32
	sub10RadioStats1mHistTime	Sub10DateTime
	sub10RadioStats1mHistTxPowerMin	Integer32
	sub10RadioStats1mHistTxPowerMax	Integer32
	sub10RadioStats1mHistTxPowerAvg	Integer32
	sub10RadioStats1mHistRxPowerMin	OCTET STRING
	sub10RadioStats1mHistRxPowerMax	OCTET STRING
	sub10RadioStats1mHistRxPowerAvg	OCTET STRING
	sub10RadioStats1mHistVectErrMin	OCTET STRING
	sub10RadioStats1mHistVectErrMax	OCTET STRING
	sub10RadioStats1mHistVectErrAvg	OCTET STRING
	sub10RadioStats1mHistLnkLossMin	OCTET STRING
	sub10RadioStats1mHistLnkLossMax	OCTET STRING
	sub10RadioStats1mHistLnkLossAvg	OCTET STRING
	sub10RadioStats1mHistMWUTempMin	Integer32
	sub10RadioStats1mHistMWUTempMax	Integer32
	sub10RadioStats1mHistMWUTempAvg	Integer32
	sub10RadioStats1mHistRxFrms	Counter64
	sub10RadioStats1mHistTxFrms	Counter64
	sub10RadioStats1mHistRxPkts	Counter64
	sub10RadioStats1mHistTxPkts	Counter64
	sub10RadioStats1mHistRxMgmtPkts	Counter64
	sub10RadioStats1mHistTxMgmtPkts	Counter64
	sub10RadioStats1mHistRxBadFrms	Counter64
	sub10RadioStats1mHistQPSKTo8PSK	Counter32
	sub10RadioStats1mHist8PSKToQPSK	Counter32
	sub10RadioStats1mHistAFERMin	OCTET STRING
	sub10RadioStats1mHistAFERMax	OCTET STRING
	sub10RadioStats1mHistAFERAvg	OCTET STRING
	sub10RadioStats1mHistRxQPSK	Counter32
	sub10RadioStats1mHistRx8PSK	Counter32
	sub10RadioStats1mHistTxQPSK	Counter32
	sub10RadioStats1mHistTx8PSK	Counter32

Sub10RadioStats15mHistEntry
SEQUENCE
	sub10RadioStats15mHistIntvl	Unsigned32
	sub10RadioStats15mHistTime	Sub10DateTime
	sub10RadioStats15mHistTxPowerMin	Integer32
	sub10RadioStats15mHistTxPowerMax	Integer32
	sub10RadioStats15mHistTxPowerAvg	Integer32
	sub10RadioStats15mHistRxPowerMin	OCTET STRING
	sub10RadioStats15mHistRxPowerMax	OCTET STRING
	sub10RadioStats15mHistRxPowerAvg	OCTET STRING
	sub10RadioStats15mHistVectErrMin	OCTET STRING
	sub10RadioStats15mHistVectErrMax	OCTET STRING
	sub10RadioStats15mHistVectErrAvg	OCTET STRING
	sub10RadioStats15mHistLnkLossMin	OCTET STRING
	sub10RadioStats15mHistLnkLossMax	OCTET STRING
	sub10RadioStats15mHistLnkLossAvg	OCTET STRING
	sub10RadioStats15mHistMWUTempMin	Integer32
	sub10RadioStats15mHistMWUTempMax	Integer32
	sub10RadioStats15mHistMWUTempAvg	Integer32
	sub10RadioStats15mHistRxFrms	Counter64
	sub10RadioStats15mHistTxFrms	Counter64
	sub10RadioStats15mHistRxPkts	Counter64
	sub10RadioStats15mHistTxPkts	Counter64
	sub10RadioStats15mHistRxMgmtPkts	Counter64
	sub10RadioStats15mHistTxMgmtPkts	Counter64
	sub10RadioStats15mHistRxBadFrms	Counter64
	sub10RadioStats15mHistQPSKTo8PSK	Counter32
	sub10RadioStats15mHist8PSKToQPSK	Counter32
	sub10RadioStats15mHistAFERMin	OCTET STRING
	sub10RadioStats15mHistAFERMax	OCTET STRING
	sub10RadioStats15mHistAFERAvg	OCTET STRING
	sub10RadioStats15mHistRxQPSK	Counter32
	sub10RadioStats15mHistRx8PSK	Counter32
	sub10RadioStats15mHistTxQPSK	Counter32
	sub10RadioStats15mHistTx8PSK	Counter32

Sub10RadioStats1dHistEntry
SEQUENCE
	sub10RadioStats1dHistIntvl	Unsigned32
	sub10RadioStats1dHistTime	Sub10DateTime
	sub10RadioStats1dHistTxPowerMin	Integer32
	sub10RadioStats1dHistTxPowerMax	Integer32
	sub10RadioStats1dHistTxPowerAvg	Integer32
	sub10RadioStats1dHistRxPowerMin	OCTET STRING
	sub10RadioStats1dHistRxPowerMax	OCTET STRING
	sub10RadioStats1dHistRxPowerAvg	OCTET STRING
	sub10RadioStats1dHistVectErrMin	OCTET STRING
	sub10RadioStats1dHistVectErrMax	OCTET STRING
	sub10RadioStats1dHistVectErrAvg	OCTET STRING
	sub10RadioStats1dHistLnkLossMin	OCTET STRING
	sub10RadioStats1dHistLnkLossMax	OCTET STRING
	sub10RadioStats1dHistLnkLossAvg	OCTET STRING
	sub10RadioStats1dHistMWUTempMin	Integer32
	sub10RadioStats1dHistMWUTempMax	Integer32
	sub10RadioStats1dHistMWUTempAvg	Integer32
	sub10RadioStats1dHistRxFrms	Counter64
	sub10RadioStats1dHistTxFrms	Counter64
	sub10RadioStats1dHistRxPkts	Counter64
	sub10RadioStats1dHistTxPkts	Counter64
	sub10RadioStats1dHistRxMgmtPkts	Counter64
	sub10RadioStats1dHistTxMgmtPkts	Counter64
	sub10RadioStats1dHistRxBadFrms	Counter64
	sub10RadioStats1dHistQPSKTo8PSK	Counter64
	sub10RadioStats1dHist8PSKToQPSK	Counter64
	sub10RadioStats1dHistAFERMin	OCTET STRING
	sub10RadioStats1dHistAFERMax	OCTET STRING
	sub10RadioStats1dHistAFERAvg	OCTET STRING
	sub10RadioStats1dHistRxQPSK	Counter32
	sub10RadioStats1dHistRx8PSK	Counter32
	sub10RadioStats1dHistTxQPSK	Counter32
	sub10RadioStats1dHistTx8PSK	Counter32

Defined Values

sub10Systems		1.3.6.1.4.1.39003
Sub10 Systems MIB
MODULE-IDENTITY

sub10Notifications		1.3.6.1.4.1.39003.0
OBJECT IDENTIFIER

sub10Unit		1.3.6.1.4.1.39003.3
OBJECT IDENTIFIER

sub10UnitStatus		1.3.6.1.4.1.39003.3.1
OBJECT IDENTIFIER

sub10UnitLocalStatus		1.3.6.1.4.1.39003.3.1.1
OBJECT IDENTIFIER

sub10UnitRemoteStatus		1.3.6.1.4.1.39003.3.1.2
OBJECT IDENTIFIER

sub10UnitMgmt		1.3.6.1.4.1.39003.3.2
OBJECT IDENTIFIER

sub10UnitMgmtSystem		1.3.6.1.4.1.39003.3.2.1
OBJECT IDENTIFIER

sub10UnitMgmtIp		1.3.6.1.4.1.39003.3.2.2
OBJECT IDENTIFIER

sub10UnitMgmtVlan		1.3.6.1.4.1.39003.3.2.3
OBJECT IDENTIFIER

sub10UnitMgmtUsers		1.3.6.1.4.1.39003.3.2.4
OBJECT IDENTIFIER

sub10UnitMgmtTime		1.3.6.1.4.1.39003.3.2.5
OBJECT IDENTIFIER

sub10UnitMgmtAlarms		1.3.6.1.4.1.39003.3.2.6
OBJECT IDENTIFIER

sub10UnitMgmtSnmp		1.3.6.1.4.1.39003.3.2.7
OBJECT IDENTIFIER

sub10UnitMgmtSmtp		1.3.6.1.4.1.39003.3.2.8
OBJECT IDENTIFIER

sub10UnitMgmtFirmware		1.3.6.1.4.1.39003.3.2.9
OBJECT IDENTIFIER

sub10UnitMgmtDNS		1.3.6.1.4.1.39003.3.2.10
OBJECT IDENTIFIER

sub10UnitMgmtEncryption		1.3.6.1.4.1.39003.3.2.11
OBJECT IDENTIFIER

sub10UnitMgmtLicense		1.3.6.1.4.1.39003.3.2.12
OBJECT IDENTIFIER

sub10UnitMgmtSyncE		1.3.6.1.4.1.39003.3.2.13
OBJECT IDENTIFIER

sub10UnitMgmtActions		1.3.6.1.4.1.39003.3.2.20
OBJECT IDENTIFIER

sub10Ethernet		1.3.6.1.4.1.39003.4
OBJECT IDENTIFIER

sub10EthernetStatus		1.3.6.1.4.1.39003.4.1
OBJECT IDENTIFIER

sub10EthernetLocalStatus		1.3.6.1.4.1.39003.4.1.1
OBJECT IDENTIFIER

sub10EthernetRemoteStatus		1.3.6.1.4.1.39003.4.1.2
OBJECT IDENTIFIER

sub10EthernetMgmt		1.3.6.1.4.1.39003.4.2
OBJECT IDENTIFIER

sub10EthMgmtPhy		1.3.6.1.4.1.39003.4.2.1
OBJECT IDENTIFIER

sub10EthMgmtVlan		1.3.6.1.4.1.39003.4.2.2
OBJECT IDENTIFIER

sub10EthMgmtQoS		1.3.6.1.4.1.39003.4.2.3
OBJECT IDENTIFIER

sub10EthMgmtStats		1.3.6.1.4.1.39003.4.2.4
OBJECT IDENTIFIER

sub10EthernetStats		1.3.6.1.4.1.39003.4.3
OBJECT IDENTIFIER

sub10EthernetStatsCurrent		1.3.6.1.4.1.39003.4.3.2
OBJECT IDENTIFIER

sub10EthernetStatsHistory		1.3.6.1.4.1.39003.4.3.3
OBJECT IDENTIFIER

sub10EthernetStats15mHistory		1.3.6.1.4.1.39003.4.3.3.1
OBJECT IDENTIFIER

sub10EthStats1dHistory		1.3.6.1.4.1.39003.4.3.3.2
OBJECT IDENTIFIER

sub10Radio		1.3.6.1.4.1.39003.5
OBJECT IDENTIFIER

sub10RadioStatus		1.3.6.1.4.1.39003.5.1
OBJECT IDENTIFIER

sub10RadioLocalStatus		1.3.6.1.4.1.39003.5.1.1
OBJECT IDENTIFIER

sub10RadioRemoteStatus		1.3.6.1.4.1.39003.5.1.2
OBJECT IDENTIFIER

sub10RadioMgmt		1.3.6.1.4.1.39003.5.2
OBJECT IDENTIFIER

sub10RadioMgmtStats		1.3.6.1.4.1.39003.5.2.9
OBJECT IDENTIFIER

sub10RadioStats		1.3.6.1.4.1.39003.5.3
OBJECT IDENTIFIER

sub10RadioStatsCurrent		1.3.6.1.4.1.39003.5.3.2
OBJECT IDENTIFIER

sub10RadioStatsHistory		1.3.6.1.4.1.39003.5.3.3
OBJECT IDENTIFIER

sub10RadioStats1mHistory		1.3.6.1.4.1.39003.5.3.3.1
OBJECT IDENTIFIER

sub10RadioStats15mHistory		1.3.6.1.4.1.39003.5.3.3.2
OBJECT IDENTIFIER

sub10RadioStats1dHistory		1.3.6.1.4.1.39003.5.3.3.3
OBJECT IDENTIFIER

sub10MIBConformance		1.3.6.1.4.1.39003.20
OBJECT IDENTIFIER

sub10MIBCompliances		1.3.6.1.4.1.39003.20.1
OBJECT IDENTIFIER

sub10MIBGroups		1.3.6.1.4.1.39003.20.2
OBJECT IDENTIFIER

sub10UnitAlarm		1.3.6.1.4.1.39003.0.1
A measured object relating the Unit subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable.
Status: current	Access: read-only
NOTIFICATION-TYPE

sub10EthernetAlarm		1.3.6.1.4.1.39003.0.2
A measured object relating the Ethernet subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable.
Status: current	Access: read-only
NOTIFICATION-TYPE

sub10RadioAlarm		1.3.6.1.4.1.39003.0.3
A measured object relating the Radio subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable.
Status: current	Access: read-only
NOTIFICATION-TYPE

sub10UnitLclTime		1.3.6.1.4.1.39003.3.1.1.1
The local system time as a display string in the format:- YYYY-MM-DD,HH:MM:SS e.g. 2014-5-26,13:30:15
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10UnitLclUnitType		1.3.6.1.4.1.39003.3.1.1.2
Uniquely identifies the local unit product type
Status: current	Access: read-only
OBJECT-TYPE
	Sub10UnitType

sub10UnitLclDescription		1.3.6.1.4.1.39003.3.1.1.3
The description of the local unit. This is synonymous with MIB-II sysDescr.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sub10UnitLclHWSerialNumber		1.3.6.1.4.1.39003.3.1.1.4
The hardware serial number of the Local Unit. This also identifies whether the unit is a V-band or E-band product. See sub10UnitLclMWUType.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..18)

sub10UnitLclTerminalName		1.3.6.1.4.1.39003.3.1.1.5
The administratively assigned name for the unit. This is synonymous with MIB-II sysName and can be administratively set via either sysName or sub10UnitMgmtTerminalName.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitLclTerminalType		1.3.6.1.4.1.39003.3.1.1.6
Uniquely identifies the local terminal type A or B.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10TerminalType

sub10UnitLclLinkName		1.3.6.1.4.1.39003.3.1.1.7
The administratively assigned name for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location. This is synonymous with MIB-II sysLocation and can be administratively set via either sysLocation or sub10UnitMgmtLinkName.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitLclLinkId		1.3.6.1.4.1.39003.3.1.1.8
The administratively assigned identifier for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitLclSiteName		1.3.6.1.4.1.39003.3.1.1.9
The administratively assigned physical location of the local unit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sub10UnitLclFirmwareLoadedBank		1.3.6.1.4.1.39003.3.1.1.10
Currently loaded bank. The firmware version running in this bank is defined by sub10UnitLclFirmwareVersion.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitLclFirmwareVersion		1.3.6.1.4.1.39003.3.1.1.11
The firmware version currently running on the local unit. This is by definition the firmware loaded into the bank number defined in sub10UnitLclFirmwareLoadedBank.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitLclIpAddress		1.3.6.1.4.1.39003.3.1.1.12
The IP address of the local ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitLclMWUTemperature		1.3.6.1.4.1.39003.3.1.1.13
The modem temperature on the local unit in degrees celsius.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10UnitLclNTPSyncStatus		1.3.6.1.4.1.39003.3.1.1.14
The indication that the systems clock is synchronised with the NTP server.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10NTPSyncStatus

sub10UnitLclAlarmStateTable		1.3.6.1.4.1.39003.3.1.1.15
The table listing the each active alarm the local unit. An active alarm is where the alarm state is 'raised' at the specific severity level. The entries in the table correspond to the configured entries in sub10UnitMgmtAlarmTable. This table has a single entry per alarm where the index to the table is the same index as the associated Alarm configuration table sub10UnitMgmtAlarmTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitLclAlarmStateEntry

sub10UnitLclAlarmStateEntry		1.3.6.1.4.1.39003.3.1.1.15.1
An entry (row) in the sub10UnitLclAlarmStateTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitLclAlarmStateEntry

sub10UnitLclAlarmStateIndex		1.3.6.1.4.1.39003.3.1.1.15.1.1
The sub10UnitLclAlarmStateTable index. The index represents the same index as used in sub10UnitMgmtAlarmTable. The entries in the table correspond to the configured entries in sub10UnitMgmtAlarmTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10AlarmIndex

sub10UnitLclAlarmState		1.3.6.1.4.1.39003.3.1.1.15.1.2
Internal object to indicate if this alarm is currently in the raised or cleared state.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10AlarmState

sub10UnitLclAlarmStateTime		1.3.6.1.4.1.39003.3.1.1.15.1.3
The local date and time when the last Alarm State transition occurred. This object facilitates retrieving all instances of alarms that have been raised or have changed state since a given point in time. Implementations MUST include the offset from UTC, if available. Implementation in environments in which the UTC offset is not available is NOT RECOMMENDED.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10UnitLclRadioDataRate		1.3.6.1.4.1.39003.3.1.1.16
The maximum data rate of the Airside interface. This has the same value as sub10RadioLclDataRate.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10RadioDataRate

sub10UnitLclMWUType		1.3.6.1.4.1.39003.3.1.1.17
The local MWU type
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MWUType

sub10UnitLclFPGAVersion		1.3.6.1.4.1.39003.3.1.1.18
The FPGA Version.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitRmtUnitType		1.3.6.1.4.1.39003.3.1.2.1
Uniquely identifies the remote unit product type
Status: current	Access: read-only
OBJECT-TYPE
	Sub10UnitType

sub10UnitRmtTime		1.3.6.1.4.1.39003.3.1.2.2
The remote unit local system time as a display string in the format:- YYYY-MM-DD,HH:MM:SS e.g. 2014-5-26,13:30:15
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10UnitRmtTerminalName		1.3.6.1.4.1.39003.3.1.2.3
The administratively assigned name for the remote unit. This is synonymous with MIB-II sysName.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitRmtTerminalType		1.3.6.1.4.1.39003.3.1.2.4
Uniquely identifies the remote terminal type A or B.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10TerminalType

sub10UnitRmtLinkName		1.3.6.1.4.1.39003.3.1.2.5
The administratively assigned name on the remote unit for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitRmtLinkId		1.3.6.1.4.1.39003.3.1.2.6
The administratively assigned identifier on the remote unit for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitRmtHWSerialNumber		1.3.6.1.4.1.39003.3.1.2.7
The hardware serial number of the Remote Unit. This also identifies whether the unit is a V-band or E-band product.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..18)

sub10UnitRmtFirmwareVersion		1.3.6.1.4.1.39003.3.1.2.8
The firmware version currently running on the remote unit. This is by definition the firmware loaded into the bank currently used for boot. See sub10UnitMgmtFirmware.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitRmtIpAddress		1.3.6.1.4.1.39003.3.1.2.9
The IP address of the remote ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitRmtMWUTemperature		1.3.6.1.4.1.39003.3.1.2.10
The modem temperature on the local unit in degrees celsius.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10UnitMgmtTerminalName		1.3.6.1.4.1.39003.3.2.1.1
The administratively assigned name for the unit. This is synonymous with MIB-II sysName and sub10UnitLocalStatus sub10UnitLclTerminalName.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitMgmtLinkName		1.3.6.1.4.1.39003.3.2.1.2
The administratively assigned name for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location. This is synonymous with sub10UnitLocalStatus sub10UnitLclLinkName
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitMgmtLinkId		1.3.6.1.4.1.39003.3.2.1.3
The administratively assigned identifier for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units. This is synonymous with sub10UnitLocalStatus sub10UnitLclLinkId. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtSiteName		1.3.6.1.4.1.39003.3.2.1.4
The administratively assigned physical location of the unit. This is synonymous with MIB-II sysLocation and sub10UnitLocalStatus sub10UnitLclSiteName.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sub10UnitMgmtContactName		1.3.6.1.4.1.39003.3.2.1.5
The administratively assigned contact for support of the unit. This is synonymous with MIB-II sysContact and sub10UnitLocalStatus sub10UnitLclContactName.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sub10UnitMgmtIpMode		1.3.6.1.4.1.39003.3.2.2.1
IP Address configuration is either manually set as ipv4 or ipv6 type addreessing or alternatively can be dynamically assigned automatically using the Dynamic Host Control Protocol (DHCP). IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ipv4(1), ipv6(2), dhcp(3)

sub10UnitMgmtIpAddress		1.3.6.1.4.1.39003.3.2.2.2
The administratively assigned IP Address for the management channel. This is reflected in the MIB-II ipAddrTable. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitMgmtIpSubnetMask		1.3.6.1.4.1.39003.3.2.2.3
The administratively assigned sub-net mask for the management channel. This is reflected in the MIB-II ipAddrTable. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitMgmtIpDefGateway		1.3.6.1.4.1.39003.3.2.2.4
The administratively assigned default gateway for the management channel. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitMgmtIpDHCP		1.3.6.1.4.1.39003.3.2.2.5
Dynamic Host Control Protocol (DHCP) is enabled or disabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtVlanState		1.3.6.1.4.1.39003.3.2.3.1
Enable VLAN for Management traffic. .
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtVlanId		1.3.6.1.4.1.39003.3.2.3.2
The VLAN Id used to carry management traffic. Only valid when the object is set to a non-zero value. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10VlanId

sub10UnitMgmtVlanPriority		1.3.6.1.4.1.39003.3.2.3.3
The VLAN priority inserted into the ethernet frame for all management traffic. Only valid when the object sub10UnitMgmtVlanId is set to non zero. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..7

sub10UnitMgmtVlanDSCP		1.3.6.1.4.1.39003.3.2.3.4
The Differentiated Services Code Point priority inserted into the IP header of all management traffic. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..63

sub10UnitMgmtVlanDEI		1.3.6.1.4.1.39003.3.2.3.5
Set the Drop Eligible Indicator inserted into the ethernet frame for all management traffic. Only valid when the object sub10UnitMgmtVlanId is set to non zero. The DEI bit is set into the tag control information (TCI) field of each management frame. The DEI is a 1 bit field immediately following the PCP bits (3 bit field) IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtUsersNumber		1.3.6.1.4.1.39003.3.2.4.1
The number of valid sub10UnitMgmtUsersTable table entries present on this system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..10

sub10UnitMgmtUserTable		1.3.6.1.4.1.39003.3.2.4.2
The table listing the users configured on the unit. The number of user entries is sub10UnitMgmtUsersNumber. This table is indexed by user name (sub10UnitMgmtUserName). Multiple entries with the same sub10UnitMgmtUserName are not possible. NB. As part of SNMPv3 support this table will be superceded by 'usmUserTable'.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtUserEntry

sub10UnitMgmtUserEntry		1.3.6.1.4.1.39003.3.2.4.2.1
An entry (row) in the sub10UnitMgmtUserTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. Usage is as follows: active(1) - Entry is created and in use. Any attempt to set this value will first check for consistent objects. If objects are found to be inconsistent then the entry will not be created and an error will be returned. notInService(2) - Entry is not created and not in use. Any attempt to set this value will result in the the entry remaining created but not accessible and not used. notReady(3) - Entry is created but has inconsistent objects, these must be set to correct values before the object can be set to active(1). createAndGo(4) - Set this to create a new entry and attempt to make the entry active(1). If the entry has inconsistent objects then this will set the entry to notReady(3) and an error will be returned. createAndWait(5)- Set this to create a new entry. This will set rowStatus = notReady(3). Related objects can then be set to consistent values before row_status can be set to active(1). destroy(6) - Set this to delete an entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtUserEntry

sub10UnitMgmtUserIndex		1.3.6.1.4.1.39003.3.2.4.2.1.1
The sub10UnitMgmtUserTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..16

sub10UnitMgmtUserRowStatus		1.3.6.1.4.1.39003.3.2.4.2.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtUserName		1.3.6.1.4.1.39003.3.2.4.2.1.3
The unique user name provided by the system administrator.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..32)

sub10UnitMgmtUserGroup		1.3.6.1.4.1.39003.3.2.4.2.1.4
The user group provided by the system administrator. This restricts a user to certain key functions on the web GUI.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10UserGroup

sub10UnitMgmtUserPassword		1.3.6.1.4.1.39003.3.2.4.2.1.5
The unique user password provided by the system administrator. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtUserPasswordVerify		1.3.6.1.4.1.39003.3.2.4.2.1.6
The unique user password provided by the system administrator use to verify the setting of sub10UnitMgmtUserPassword. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtTimeLocal		1.3.6.1.4.1.39003.3.2.5.1
The administratively assigned system time defined as a display string in the format:- YYYY-MM-DD HH:MM:SS e.g. 2014-05-26 13:30:15
Status: current	Access: read-write
OBJECT-TYPE
	Sub10DateTime

sub10UnitMgmtTimeNTPEnabled		1.3.6.1.4.1.39003.3.2.5.2
The administratively assigned state to enable or disable NTP. system cloack assignment automatically using the Network Time Protocol (NTP).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtTimeNTPServer1		1.3.6.1.4.1.39003.3.2.5.3
The administratively assigned primary NTP Server name.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..127)

sub10UnitMgmtTimeNTPServer2		1.3.6.1.4.1.39003.3.2.5.4
The administratively assigned secondary NTP Server name to be used when the primary server is not responding.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1..127)

sub10UnitMgmtTimeNTPPort		1.3.6.1.4.1.39003.3.2.5.5
The administratively assigned NTP Port number name to be used when contacting the NTP server.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..65535

sub10UnitMgmtTimeNTPSyncStatus		1.3.6.1.4.1.39003.3.2.5.6
The indication that the systems clock is synchronised with the NTP server.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10NTPSyncStatus

sub10UnitMgmtDateTime		1.3.6.1.4.1.39003.3.2.5.7
The administratively assigned system defined as a standard date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

sub10UnitMgmtAlarmTable		1.3.6.1.4.1.39003.3.2.6.1
The sub10UnitMgmtAlarmTable defines the alarm configuration. The first 'N' rows of the table is reserved for fixed alarms defined by the manufacturer. Fixed alarms cannot be deleted or their names changed, other attributes of a fixed alarm may be modified. The remainder of rows are available for user defined alarms which can be created and deleted. The index value 'N' is defined by 'sub10UnitMgmtAlarmsUserDefStart'. Any attempt to create or delete a row in the table with an index less than value of 'sub10UnitMgmtAlarmsUserDefStart' will be rejected. This table is indexed by alarm index a number ranging from 1 to the maximum number of entries in the alarm table. User defined alarm name and and alarm severity are configurable allowing multiple entries for the same alarm to be raised at different severity levels according to different threshold levels. A user defined alarm can be created with the same name as a fixed alarm if required. For example the fixed alarm 'Rx Power Low' monitors the radio receive power and raises an alarm if the value is less than a certain threshold. A user defined alarm may be created with the same name but a less stringent threshold and a lower seveirty level. This allows same alarms to be raised at increasing severity as the condition causing the alarm worsens. This table allows configuration of threshold passing behavior, threshold values for both raising and clearing the alarms and the perceived severity. The alarm forwarding mechanisms can be defined for example SNMP trap, syslog and SMTP. No validation of thresholds across different entries of the table therefore the administrator must ensure that thresholds are correctly set accordingly for the severity of each alarm. This is particularly important where a single alarm name is configured to be raised at different severity levels.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtAlarmEntry

sub10UnitMgmtAlarmEntry		1.3.6.1.4.1.39003.3.2.6.1.1
An entry (row) in the sub10UnitMgmtAlarmTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtAlarmEntry

sub10UnitMgmtAlarmIndex		1.3.6.1.4.1.39003.3.2.6.1.1.1
The sub10UnitMgmtAlarmTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10AlarmIndex

sub10UnitMgmtAlarmRowStatus		1.3.6.1.4.1.39003.3.2.6.1.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtAlarmName		1.3.6.1.4.1.39003.3.2.6.1.1.3
The alarm name. This is a short descriptive name for the alarm. Alarm names can be duplicated across entries in order to define the same alarm to be raised and cleared according to different thresholds and different severity levels. If the user defines mutiple alarms with the same name it important to correctly configure severity and thresholds to avoid multiple alarms being generated for the same condition. Fixed alarm names cannot be modified. Fixed alarms are populated automatically in rows 1 to ('sub10UnitMgmtAlarmsUserDefStart'-1)
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlarmName

sub10UnitMgmtAlarmSeverity		1.3.6.1.4.1.39003.3.2.6.1.1.4
The alarm severity. This is added to each alarm as a parameter.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlarmSeverity

sub10UnitMgmtAlarmMeasObject		1.3.6.1.4.1.39003.3.2.6.1.1.5
The measured object. This is the object name of the object in the MIB with which the alarm is associated and which the configured thresholds are compared with when deriving the state of the alarm. It is not neccessary for all alarm measurement values to be identified in the MIB since a single alarm may be dependant on checks against entities or objects which are not present in the MIB and therefore do not have an associated OID. In general where an alarm and its thresholds relate to the monitoring of the value of a single MIB object then the OID of that object will be defined here otherwise the value is set to empty string.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10MeasuredObject

sub10UnitMgmtAlarmMonitorIntvl		1.3.6.1.4.1.39003.3.2.6.1.1.6
The interval in seconds when the measured object is to be read and compared with the raise and clear thresholds. An alarm cannot be raised or cleared quicker than the configured interval. Please also see related sub10UnitMgmtAlarmRaiseIntvls and sub10UnitMgmtAlarmClearIntvls objects which also affect when alarms are raised and cleared. This object should be set appropriately for the measured object to be monitored (see sub10UnitMgmtAlarmRaiseMeasObject) and the resulting alarm to be raised and cleared (see sub10UnitMgmtAlarmName). This also affects the forwarding of alarms for example as SNMP notifications. Higher severity alarms may have a shorter interval than those at a lower severity. The correct setting of sub10UnitMgmtAlarmMonitorIntvl and related objects sub10UnitMgmtAlarmRaiseIntvls and sub10UnitMgmtAlarmClearIntvls are important to avoid potential network loading caused by alarm storms.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..86400

sub10UnitMgmtAlarmRaiseOper		1.3.6.1.4.1.39003.3.2.6.1.1.7
Type of operation which determines when an alarm is to be raised. Definition of each type is as follows: lt - Measured objects value is less than raise threshold gt - Measured objects value is greater than raise threshold le - Measured objects value is less than or equal to raise threshold ge - Measured objects value is greater than or equal to raise threshold eq - Measured objects value is equal to raise threshold neq - Measured objects value is not equal to raise threshold The alarm operation defines how to apply the configured thresholds when raising the alarm. This defines whether the alarm is raised when the measured object value crosses the threshold from low to high or from high to low or if the measured value hits a certain value or not. Example: Alarm Name Alarm Threshold Raise Operation High Temperature 70 gt Low Temperature -30 le High Temperature Alarm is raised when the measured temperature is above 70 and Low Temperature raised when the measured temperature is lower than or equal to -30.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlarmOperation

sub10UnitMgmtAlarmRaiseThresh		1.3.6.1.4.1.39003.3.2.6.1.1.8
The threshold value which the measured object's value crosses causes the alarm to be raised. The behaviour of a measured value and alarm threshold comparison is defined by the object sub10UnitMgmtAlarmThreshType.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtAlarmClearOper		1.3.6.1.4.1.39003.3.2.6.1.1.9
Type of operation which determines when an alarm is to be cleared. Definition of each type is as follows: lt - Measured objects value is less than clear threshold gt - Measured objects value is greater than clear threshold le - Measured objects value is less than or equal to clear threshold ge - Measured objects value is greater than or equal to clear threshold eq - Measured objects value is equal to clear threshold neq - Measured objects value is not equal to clear threshold The alarm operation defines how to apply the configured thresholds when clearing the alarm. This defines whether the alarm is cleared when the measured object value crosses the threshold from low to high or from high to low or if the measured value hits a certain value or not. Example: Alarm Name Alarm Threshold Clear Operation High Temperature 60 le Low Temperature -30 gt Low Temperature Alarm is cleared when the measured temperature is lower or equal to 60 and Low Temperature cleared when the measured temperature is greater than -30.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlarmOperation

sub10UnitMgmtAlarmClearThresh		1.3.6.1.4.1.39003.3.2.6.1.1.10
The threshold value which the measured object's value crosses causes the alarm to be cleared. The behaviour of a measured value and alarm threshold comparison is defined by the object sub10UnitMgmtAlarmThreshType. The sub10UnitMgmtAlarmClearThresh value may be different to the sub10UnitMgmtAlarmRaiseThresh allowing some hysteresis bewteen raising and clearing of alarms thus avoiding an alarm being continually raised and cleared if the measured value is changing frequently around the threshold. If different raise and clear thresholds are not required then the sub10UnitMgmtAlarmClearThresh and sub10UnitMgmtAlarmRaiseThresh should be set to the same value.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtAlarmRaiseIntvls		1.3.6.1.4.1.39003.3.2.6.1.1.11
The number of continuous monitoring intervals (see sub10UnitMgmtAlarmMonitorIntvl) where the measured object has crossed the raise threshold before the alarm state is set to raised. This is intended to reduce the number of alarm state transitions when the measured object value is rapidly changing close to the configured raise threshold.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

sub10UnitMgmtAlarmClearIntvls		1.3.6.1.4.1.39003.3.2.6.1.1.12
The number of continuous monitoring intervals (see sub10UnitMgmtAlarmMonitorIntvl) where the measured object has crossed the clear threshold before the alarm state is set to cleared. This is intended to reduce the number of alarm state transitions when the measured object value is rapidly changing close to the configured clear threshold.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

sub10UnitMgmtAlarmType		1.3.6.1.4.1.39003.3.2.6.1.1.13
The type of the alarm and defines the type of notification (trap) used to inform management entities.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlarmType

sub10UnitMgmtAlarmSmtpAddress		1.3.6.1.4.1.39003.3.2.6.1.1.14
The smtp mail address. If set the alarm is suitable formatted and sent to the given mail address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..63)

sub10UnitMgmtAlarmToSyslog		1.3.6.1.4.1.39003.3.2.6.1.1.15
If set to 'enabled' the alarm is suitably formatted and sent to syslog.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtAlarmEnabled		1.3.6.1.4.1.39003.3.2.6.1.1.16
If set to 'enabled' the alarm is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtAlarmMeasObjectVal		1.3.6.1.4.1.39003.3.2.6.1.1.17
The value of sub10UnitMgmtAlarmMeasObject formatted as a displayString which when measured by the alarm subsystem caused an alarm to be either raised or cleared. This is therefore the value of the object which was compared with and found to have crossed the configured threshold causing the alarm to change state. The value is not the current value of the measured object it is the observed value which caused the change in alarm state.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

sub10UnitMgmtAlarmToSNMP		1.3.6.1.4.1.39003.3.2.6.1.1.18
If set to 'enabled' the alarm is forwarded as an SNMP notification / trap.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtAlarmMeasObjIndex		1.3.6.1.4.1.39003.3.2.6.1.1.19
The measured object's index which is a value from 1 and is the instance of the measured object to be monitored. For scalar objects this value is 0 and for non-scalar (or column) objects this value must be 0 or greater and must match the index value defined for the object where the object is defined as a column in a table and the table has an index defined in a certain range.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

sub10UnitMgmtAlarmsUserDefStart		1.3.6.1.4.1.39003.3.2.6.2
This defines the row index from which point rows in the sub10UnitMgmtAlarmTable can be created and deleted and therefore where user defined alarms start. Any attempt to create or delete a row in the sub10UnitMgmtAlarmTable with an index below this value will fail.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10AlarmIndex

sub10UnitMgmtSnmpAgent		1.3.6.1.4.1.39003.3.2.7.1
If set to 'enabled' the agent will respond to valid v1/2c SNMP requests for GET/SET/GET-NEXT of supported MIB objects. If this object and the object sub10UnitMgmtSnmpv3 are both set to disabled then the unit will no longer respond to SNMP requests. If this object is set to enabled and sub10UnitMgmtSnmpv3 is set to enabled then the agent will respond to both both v1/2c and v3 SNMP requests. !! IMPORTANT !! If this object and sub10UnitMgmtSnmpv3 is set to disabled then the Agent will no longer respond therefore it will not be possible to re-enable the agent using SNMP. The agent can be re-enabled using the web GUI only. If this object is disabled then traps will not be forwarded by the unit.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtSnmpTraps		1.3.6.1.4.1.39003.3.2.7.2
If set to 'enabled' the agent will forward traps to all configured trap destinations. If disabled traps are discarded. Traps are not sent if sub10UnitMgmtSnmpAgent is 'disabled(2)' regardless of the setting of this object.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtSnmpv320Mib		1.3.6.1.4.1.39003.3.2.7.3
If set to 'enabled' the agent will support the Sub10 Systems v320 legacy MIB (LIBERATOR-MIB) objects and traps.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtSnmpv3		1.3.6.1.4.1.39003.3.2.7.4
If set to 'enabled' the agent will support SNMPv3 PDUs and the SNMPv3 MIB configuration. This can be set to enabled or disabled independently of the object sub10UnitMgmtSnmpAgent which enables or disables the v1/2c agent. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtSnmpTrpDstTable		1.3.6.1.4.1.39003.3.2.7.5
The table listing the each trap destination the local unit. Each trap destination has an IpAddress and a trap community string
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtSnmpTrpDstEntry

sub10UnitMgmtSnmpTrpDstEntry		1.3.6.1.4.1.39003.3.2.7.5.1
An entry (row) in the sub10UnitMgmtSnmpTrpDstTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtSnmpTrpDstEntry

sub10UnitMgmtSnmpTrpDstIndex		1.3.6.1.4.1.39003.3.2.7.5.1.1
The sub10UnitMgmtSnmpTrpDstTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..3

sub10UnitMgmtSnmpTrpDstRowStatus		1.3.6.1.4.1.39003.3.2.7.5.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtSnmpTrpDstIpAddr		1.3.6.1.4.1.39003.3.2.7.5.1.3
The administratively assigned SNMP Trap Destination IP.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtSnmpTrpDstCommunity		1.3.6.1.4.1.39003.3.2.7.5.1.4
The trap community name sent with each trap to this trap destination. The trap community allows for some security in the target management terminal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtSnmpEngineIdFormat		1.3.6.1.4.1.39003.3.2.7.6
The format of this SNMP v3 agent's engine id. The engine id is administratively defined and is between 5 and 32 characters long and can be based on a number of formats defined here.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v4IpAddress(1), v6IpAddress(2), macAddress(3), textString(4)

sub10UnitMgmtSnmpEngineIdText		1.3.6.1.4.1.39003.3.2.7.7
When sub10UnitMgmtSnmpEngineIdFormat='textString(4)' this object contains the administratively defined string used to build the SNMP v3 engine id in sub10UnitMgmtSnmpEngineId.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..25)

sub10UnitMgmtSnmpEngineId		1.3.6.1.4.1.39003.3.2.7.8
The administratively assigned SNMP v3 engine id. The construction of the engine id is dependant on the setting of sub10UnitMgmtSnmpEngineIdFormat and must be unique to the unit.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(5..32)

sub10UnitMgmtSnmpOperAuthProto		1.3.6.1.4.1.39003.3.2.7.9
The authentication protocol currently assigned to users of group type operation.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3AuthProtocol

sub10UnitMgmtSnmpOperPrivProto		1.3.6.1.4.1.39003.3.2.7.10
The privacy protocol currently assigned to users of group type operation.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3PrivProtocol

sub10UnitMgmtSnmpAdminAuthProto		1.3.6.1.4.1.39003.3.2.7.11
The authentication protocol currently assigned to users of group type administration.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3AuthProtocol

sub10UnitMgmtSnmpAdminPrivProto		1.3.6.1.4.1.39003.3.2.7.12
The privacy protocol currently assigned to users of group type administration.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3PrivProtocol

sub10UnitMgmtSnmpMaintAuthProto		1.3.6.1.4.1.39003.3.2.7.13
The authentication protocol currently assigned to users of group type maintenance.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3AuthProtocol

sub10UnitMgmtSnmpMaintPrivProto		1.3.6.1.4.1.39003.3.2.7.14
The privacy protocol currently assigned to users of group type maintenance.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Snmpv3PrivProtocol

sub10UnitMgmtSnmpUserTable		1.3.6.1.4.1.39003.3.2.7.15
The table of SNMPv3 User configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtSnmpUserEntry

sub10UnitMgmtSnmpUserEntry		1.3.6.1.4.1.39003.3.2.7.15.1
An entry (row) in the sub10UnitMgmtSnmpUserTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtSnmpUserEntry

sub10UnitMgmtSnmpUserIndex		1.3.6.1.4.1.39003.3.2.7.15.1.1
The sub10UnitMgmtSnmpUserTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..10

sub10UnitMgmtSnmpUserRowStatus		1.3.6.1.4.1.39003.3.2.7.15.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtSnmpUserName		1.3.6.1.4.1.39003.3.2.7.15.1.3
The administratively assigned SNMPv3 User name.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtSnmpUserGroup		1.3.6.1.4.1.39003.3.2.7.15.1.4
The user group type. Authentication and Privacy policies are assigned to a user group and not individual users.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10UserGroup

sub10UnitMgmtSnmpUserAuthPwd		1.3.6.1.4.1.39003.3.2.7.15.1.5
The unique SNMPv3 authentication protocol password provided by the system administrator. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtSnmpUserAuthPwdChk		1.3.6.1.4.1.39003.3.2.7.15.1.6
The unique SNMPv3 authentication protocol password provided by the system administrator used to verify the setting of sub10UnitMgmtSnmpUserAuthPassword. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtSnmpUserPrivPwd		1.3.6.1.4.1.39003.3.2.7.15.1.7
The unique SNMPv3 privacy protocol password provided by the system administrator. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtSnmpUserPrivPwdChk		1.3.6.1.4.1.39003.3.2.7.15.1.8
The unique SNMPv3 privacy protocol password provided by the system administrator used to verify the setting of sub10UnitMgmtSnmpUserPrivPassword. This object can be set but is not visible when read.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6..32)

sub10UnitMgmtSnmpAccessTable		1.3.6.1.4.1.39003.3.2.7.16
The table of SNMPv3 Access configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtSnmpAccessEntry

sub10UnitMgmtSnmpAccessEntry		1.3.6.1.4.1.39003.3.2.7.16.1
An entry (row) in the sub10UnitMgmtSnmpAccessTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtSnmpAccessEntry

sub10UnitMgmtSnmpAccessIndex		1.3.6.1.4.1.39003.3.2.7.16.1.1
The sub10UnitMgmtSnmpAccessTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..3

sub10UnitMgmtSnmpAccessRowStatus		1.3.6.1.4.1.39003.3.2.7.16.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtSnmpAccessName		1.3.6.1.4.1.39003.3.2.7.16.1.3
The administratively assigned SNMPv3 access name. This is used as an alias for the access address for purposes of identification. The name is not used in the SNMP protocol.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtSnmpAccessIpAddr		1.3.6.1.4.1.39003.3.2.7.16.1.4
The administratively assigned SNMP access IP address. Only SNMP requests from this address will be serviced by the SNMP agent.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtSnmpTargetTable		1.3.6.1.4.1.39003.3.2.7.17
The table of SNMPv3 Target configuration. This table defines the addresses of target SNMPv3 managers to send Notifications.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtSnmpTargetEntry

sub10UnitMgmtSnmpTargetEntry		1.3.6.1.4.1.39003.3.2.7.17.1
An entry (row) in the sub10UnitMgmtSnmpTargetTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtSnmpTargetEntry

sub10UnitMgmtSnmpTargetIndex		1.3.6.1.4.1.39003.3.2.7.17.1.1
The sub10UnitMgmtSnmpTargetTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..3

sub10UnitMgmtSnmpTargetRowStatus		1.3.6.1.4.1.39003.3.2.7.17.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10UnitMgmtSnmpTargetName		1.3.6.1.4.1.39003.3.2.7.17.1.3
The administratively assigned SNMPv3 target name.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtSnmpTargetIpAddr		1.3.6.1.4.1.39003.3.2.7.17.1.4
The administratively assigned SNMP target IP address. When enabled SNMPv3 Notifications are sent to this address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtSnmpTargetUserName		1.3.6.1.4.1.39003.3.2.7.17.1.5
The administratively assigned SNMPv3 target user name. The security model configured for this user is used when sending notifications to the target address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10UnitMgmtFirmwareSelectBank		1.3.6.1.4.1.39003.3.2.9.1
Currently selected bank which unit uses to boot.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitMgmtFirmwareLoadedBank		1.3.6.1.4.1.39003.3.2.9.2
Currently loaded bank. The firmware version number running in this bank is defined by sub10UnitMgmtFirmwareVersion.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitMgmtFirmwareVersion		1.3.6.1.4.1.39003.3.2.9.3
The firmware version currently running on the local unit. This is the version of the firmware loaded into the bank number defined in sub10UnitMgmtFirmwareLoadedBank.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtFirmwareBootVersion		1.3.6.1.4.1.39003.3.2.9.4
The firmware boot version currently running on the local unit. This is the boot version of the firmware loaded into the bank number defined in sub10UnitMgmtFirmwareLoadedBank.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtFirmwareAction		1.3.6.1.4.1.39003.3.2.9.5
The firmware bank action object is used to perform certain actions on a firmware bank. Using this it is possible to reboot the unit, copy banks and upload software to the currently inactive bank. After a Set of this object it's value is always reset to fmwNone(1). The progress of the action may be monitored using a get of the objects 'sub10UnitMgmtFirmwareActStatus' and 'sub10UnitMgmtFirmwareActProgress'. fmwNone(1) - Perform no firmware action unit. fmwReboot(2) - Perform immediate unit reboot of the unit and start the firmware currently loaded in 'sub10UnitMgmtFirmwareSelectBank'. fmwCopyInactiveBank(3) - Copy the firmware currently loaded in 'sub10UnitMgmtFirmwareLoadedBank' to the inactive bank. fmwUploadInactiveBank(4) - Upload the firmware image named by 'sub10UnitMgmtFirmwareUplImage' from the server address 'sub10UnitFirmwareUplServerIp' and load to the inactive bank.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fmwNone(1), fmwReboot(2), fmwCopyInactiveBank(3), fmwUploadInactiveBank(4)

sub10UnitMgmtFirmwareBankTable		1.3.6.1.4.1.39003.3.2.9.6
This tables contains information regarding the firmware banks.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtFirmwareBankEntry

sub10UnitMgmtFirmwareBankEntry		1.3.6.1.4.1.39003.3.2.9.6.1
An entry (row) in the sub10UnitMgmtFirmwareBankTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtFirmwareBankEntry

sub10UnitMgmtFirmwareBankIndex		1.3.6.1.4.1.39003.3.2.9.6.1.1
The sub10UnitMgmtFirmwareBankTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitMgmtFirmwareBankVersion		1.3.6.1.4.1.39003.3.2.9.6.1.2
The firmware version currently installed in this bank.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..15)

sub10UnitMgmtFirmwareBankImage		1.3.6.1.4.1.39003.3.2.9.6.1.3
The firmware image name currently installed in this bank.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sub10UnitMgmtFirmwareUplImage		1.3.6.1.4.1.39003.3.2.9.7
The firmware image name to be uploaded from the server defined by 'sub10UnitFirmwareUplServerIp' using the firmware action 'sub10UnitFirmwareAction=fmwUpload(4)'.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sub10UnitMgmtFirmwareUplSvrIp		1.3.6.1.4.1.39003.3.2.9.8
The IP address of the server used to upload the firmware image defined by sub10UnitMgmtFirmwareUplImage.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitMgmtFirmwareFromBank		1.3.6.1.4.1.39003.3.2.9.9
The bank currently being copied from by the Firmware action sub10UnitMgmtFirmwareAction = fmwCopyInactiveBank(4).
Status: current	Access: read-only
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitMgmtFirmwareToBank		1.3.6.1.4.1.39003.3.2.9.10
The bank currently being uploaded or copied to by the Firmware actions sub10UnitMgmtFirmwareAction = fmwUploadInactiveBank(4) or sub10UnitMgmtFirmwareAction = fmwCopyInactiveBank(4).
Status: current	Access: read-only
OBJECT-TYPE
	Sub10FirmwareBank

sub10UnitMgmtFirmwareActStatus		1.3.6.1.4.1.39003.3.2.9.11
The status of the firmware bank action which can be repeatedly read using a Get to report the progress of the the action and verify that it has either succeeded or failed. The value is left in the final state after the Firmware Action has completed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	fmwUploadSuccess(1), fmwUploadFailed(2), fmwUploadTimeout(3), fmwUploadFileNotFound(4), fmwUploadInvalid(5), fmwUploadingImage(6), fmwUploadingImageComplete(7), fmwUploadWritingBank(8), fmwUploadWritingBankComplete(9), fmwValidatingImage(10), fmwImageValidateSuccess(11), fmwImageValidateFailed(12), fmwCopyingBank(13), fmwCopyingBankComplete(14), fmwCopyBankFailed(15), fmwCopyBankSuccess(16)

sub10UnitMgmtFirmwareActProgress		1.3.6.1.4.1.39003.3.2.9.12
The % progress of firmware action when loading the firmware image to a firmware bank or copying a firmware image from on1 bank to another bank.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..100

sub10UnitMgmtDNSTable		1.3.6.1.4.1.39003.3.2.10.1
This tables defines the Domain Name Servers.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10UnitMgmtDNSEntry

sub10UnitMgmtDNSEntry		1.3.6.1.4.1.39003.3.2.10.1.1
An entry (row) in the sub10UnitMgmtDNSTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10UnitMgmtDNSEntry

sub10UnitMgmtDNSIndex		1.3.6.1.4.1.39003.3.2.10.1.1.1
The sub10UnitMgmtDNSTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2

sub10UnitMgmtDNServer		1.3.6.1.4.1.39003.3.2.10.1.1.2
The administratively assigned DNS server IP for the unit. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(7..15)

sub10UnitMgmtEncryptMode		1.3.6.1.4.1.39003.3.2.11.1
The administratively assigned License key for the unit. The license key enables capabilities within the unit. The capabilities currently available by the configured license key are readable objects.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	encryptNone(0), encryptAES128(1), encryptAES192(2), encryptAES256(3)

sub10UnitMgmtEncryptKey		1.3.6.1.4.1.39003.3.2.11.2
The administratively assigned Encryption key.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..128)

sub10UnitMgmtLicenseKey		1.3.6.1.4.1.39003.3.2.12.1
The administratively assigned License key for the unit. The license key enables capabilities within the unit. The capabilities currently available by the configured license key are readable objects.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..128)

sub10UnitMgmtLicenseAES		1.3.6.1.4.1.39003.3.2.12.2
Indication if AES encryption is included in the current license key.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10State

sub10UnitMgmtSyncEMode		1.3.6.1.4.1.39003.3.2.13.1
The SyncE Mode. Setting this to syncEProvider(1) configures the unit as a Slave clock. In this case the unit at the other end of the link should be set to syncEConsumer(2). IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	syncENone(0), syncEProvider(1), syncEConsumer(2)

sub10UnitMgmtTransaction		1.3.6.1.4.1.39003.3.2.20.1
This is used to commit or rollback the setting of object configuration. It only applies where the objects are subject to transactional requirements. For example the setting of the Unit's IP Address requires that a transaction be committed. If the transaction is not committed after a rollback timeout then the unit will automatically action a rollback to the previous value. The rollback timeout is configurable 'sub10UnitMgmtRollbackTimeout'
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	transactionNone(1), transactionCommit(2), transactionRollback(3)

sub10UnitMgmtTransactionStatus		1.3.6.1.4.1.39003.3.2.20.2
This indicates either a transaction is currently in progress or if the last transaction was committed successfully or was rolled back.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	transStatusNone(1), transStatusActive(2), transStatusCommitted(3), transStatusRollback(4)

sub10UnitMgmtRollbackTimeout		1.3.6.1.4.1.39003.3.2.20.3
The timeout in seconds after which uncommitted Sets will be rolled back to their previous values. A rollback only affects those objects which are subject to transactions.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	30..300

sub10UnitMgmtTransactionMode		1.3.6.1.4.1.39003.3.2.20.4
Enables and Disables transactions. If sub10UnitMgmTransactionMode is stateDisabled(0) then no objects are subject to commit and rollback.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10UnitMgmtResetAction		1.3.6.1.4.1.39003.3.2.20.5
This is used to reset unit configuration and stats. resetFactoryDefaults(2) - Resets all configuration to Factory Defaults, requires a reboot. resetStatistics(3) - Resets according to setting of sub10UnitMgmtResetStatsGroup For reset of all stats sub10UnitMgmtResetStatsGroup = 'statsGroupAll'. resetAlarmConfig(4) - Resets according to setting of sub10UnitMgmtResetAlarmsType For reset of all alarms sub10UnitMgmtResetAlarmsType = 'resetAlarmTypeAll'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	resetNone(1), resetFactoryDefaults(2), resetFactoryDefaultsNoSave(3), resetStatistics(4), resetAlarmConfig(5)

sub10UnitMgmtResetStatsGroup		1.3.6.1.4.1.39003.3.2.20.6
This is used to reset specific statistics when set prior to submitting sub10UnitMgmtResetAction = resetStatistics(4). For reset of all stats sub10UnitMgmtResetStatsGroup = 'statsGroupAll'.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10StatsGroup

sub10UnitMgmtResetAlarmsType		1.3.6.1.4.1.39003.3.2.20.7
This is used to reset specific alarm configuration when set prior to submitting sub10UnitMgmtResetAction = resetAlarmConfig(5). For reset of all alarms sub10UnitMgmtResetAlarmsType = resetAlarmTypeAll(1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	resetAlarmTypeAll(1), resetAlarmTypeFixed(2), resetAlarmTypeUser(3)

sub10EthLclStatusTable		1.3.6.1.4.1.39003.4.1.1.1
This table defines the local status objects of the ethernet interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthLclStatusEntry

sub10EthLclStatusEntry		1.3.6.1.4.1.39003.4.1.1.1.1
An entry (row) in the sub10EthLclStatusTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthLclStatusEntry

sub10EthLclLinkStatus		1.3.6.1.4.1.39003.4.1.1.1.1.1
The status of the ethernet link. Synonymous with interfaces OperState
Status: current	Access: read-only
OBJECT-TYPE
	Sub10OperStatus

sub10EthLclMacAddress		1.3.6.1.4.1.39003.4.1.1.1.1.2
The MAC address of the local ethernet interface. Synonymous with interfaces ifPhysAddress
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MacAddress

sub10EthLclSpeed		1.3.6.1.4.1.39003.4.1.1.1.1.3
The estimated speed of the local ethernet interface in bits per second. Synonymous with interfaces ifSpeed
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

sub10EthLclDuplex		1.3.6.1.4.1.39003.4.1.1.1.1.4
The duplex operation of the local ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Sub10Duplex

sub10EthLclMDI		1.3.6.1.4.1.39003.4.1.1.1.1.5
The MDI/MDIX state of the local ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MDIType

sub10EthIfIndex		1.3.6.1.4.1.39003.4.1.1.1.1.6
A unique value, greater than zero, for each ethernet interface. It is recommended that values are assigned contiguously starting from 1. This is used as an index to the ethernet based enterprise MIB tables and will reflect the number of physical ethernet ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthInterfaceIndex

sub10EthRmtStatusTable		1.3.6.1.4.1.39003.4.1.2.1
This table defines the remote status objects of the ethernet interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthRmtStatusEntry

sub10EthRmtStatusEntry		1.3.6.1.4.1.39003.4.1.2.1.1
An entry (row) in the sub10EthRmtStatusTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthRmtStatusEntry

sub10EthRmtLinkStatus		1.3.6.1.4.1.39003.4.1.2.1.1.1
The status of the remote ethernet interface. Synonymous but not identical with interfaces OperState on the remote unit
Status: current	Access: read-only
OBJECT-TYPE
	Sub10OperStatus

sub10EthRmtMacAddress		1.3.6.1.4.1.39003.4.1.2.1.1.2
The MAC address of the remote ethernet interface. Synonymous with interfaces ifPhysAddress on the remote unit.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MacAddress

sub10EthRmtSpeed		1.3.6.1.4.1.39003.4.1.2.1.1.3
The estimated speed of the remote ethernet interface in bits per second. Synonymous with interfaces ifSpeed on the remote unit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

sub10EthRmtDuplex		1.3.6.1.4.1.39003.4.1.2.1.1.4
The duplex operation of the remote ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Sub10Duplex

sub10EthRmtMDI		1.3.6.1.4.1.39003.4.1.2.1.1.5
The MDI/MDIX state of the remote ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MDIType

sub10EthMgmtPhyTable		1.3.6.1.4.1.39003.4.2.1.1
This table defines the status objects of the ethernet interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtPhyEntry

sub10EthMgmtPhyEntry		1.3.6.1.4.1.39003.4.2.1.1.1
An entry (row) in the sub10EthMgmtPhyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtPhyEntry

sub10EthMgmtPhyAutoNeg		1.3.6.1.4.1.39003.4.2.1.1.1.1
Auto-negotiation of ethernet interface parameters.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthMgmtPhySpeed		1.3.6.1.4.1.39003.4.2.1.1.1.2
Speed of the ethernet interface in bits per second used only when sub10UnitMgmtPhyAutoNeg=disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

sub10EthMgmtPhyDuplex		1.3.6.1.4.1.39003.4.2.1.1.1.3
The duplex operation of the ethernet interface used only when sub10UnitMgmtPhyAutoNeg=disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10Duplex

sub10EthMgmtPhyMDI		1.3.6.1.4.1.39003.4.2.1.1.1.4
The duplex operation of the ethernet interface used only when sub10UnitMgmtPhyAutoNeg=disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10MDIType

sub10EthMgmtVlanFiltering		1.3.6.1.4.1.39003.4.2.2.1
VLAN filtering on the ethernet interface. This applies to user traffic only not management traffic however to enable VLAN filtering a Unit Management VLAN configuration must be set. See sub10UnitMgmtVlan. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthMgmtVlanDefaultEnabled		1.3.6.1.4.1.39003.4.2.2.2
Enable Default VLAN tagging and untagging on the ethernet interface. Only valid when sub10EthMgmtVlanFiltering is enabled. Default VAN tagging allows manipulation of untagged traffic ingressing the interface by applying the specified Default VLAN Id, priority and DEI and manipulation of traffic egressing the ethernet interface that is tagged with the Default VLAN by stripping off the VLAN and transmitting as untagged traffic. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthMgmtVlanDefaultId		1.3.6.1.4.1.39003.4.2.2.3
The default vlan id which is tagged to all incoming untagged user traffic ingressing the ethernet interface. The default VLAN is also untagged from all user traffic egressing the ethernet interface. The default VLAN must be present in the allowed VLAN table sub10EthMgmtVlanAllowedTable and is only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10VlanId

sub10EthMgmtVlanDefaultPriority		1.3.6.1.4.1.39003.4.2.2.4
The default vlan priority used when tagging the default VLAN to all incoming untagged user traffic ingressing the ethernet interface. Only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10VlanPriority

sub10EthMgmtVlanDefaultDEI		1.3.6.1.4.1.39003.4.2.2.5
The default vlan drop eligible indicator used when tagging the default VLAN to all incoming untagged user traffic ingressing the ethernet interface. Only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthMgmtVlanIngressAction		1.3.6.1.4.1.39003.4.2.2.6
The manipulation action used for all ethernet frames being received (ingress) in from the ethernet interface. Only if the default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0 and sub10EthMgmtVlanFiltering is enabled. untag - untag all incoming frames that are tagged with sub10EthMgmtVlanDefaultVlanId. tag - tag all incoming untagged frames with sub10EthMgmtVlanDefaultVlanId, ,sub10EthMgmtVlanDefaultPriority and sub10EthMgmtVlanDefaultDEI. and priority sub10EthMgmtTagWithVlanPriority. drop - discard the frame, do not forward. This is currently fixed to tag all ingressing traffic if a default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10VlanTagAction

sub10EthMgmtVlanEgressAction		1.3.6.1.4.1.39003.4.2.2.7
The manipulation action used for all ethernet frames being transmitted (egress) out of the ethernet interface. Only if the default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0 and sub10EthMgmtVlanFiltering is enabled. untag - untag all outgoing frames that are tagged with sub10EthMgmtVlanDefaultVlanId. tag - tag all outgoing untagged frames with sub10EthMgmtVlanDefaultVlanId, ,sub10EthMgmtVlanDefaultPriority and sub10EthMgmtVlanDefaultDEI. and priority sub10EthMgmtTagWithVlanPriority. drop - discard the frame, do not forward. This is currently fixed to untag all egressing traffic.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10VlanTagAction

sub10EthMgmtVlanAllowedTable		1.3.6.1.4.1.39003.4.2.2.8
This tables defines the VLANs that are allowed to pass through the ethernet interface. The table is only used when the value of sub10EthMgmtVlanFiltering is enabled. The table only contains an entry if the specific vlan is to be allowed to flow through the interface. If a VLAN is not in the table then the ethernet frame is dropped. If sub10EthMgmtVlanFiltering is enabled this table must contain at least 1 VLAN. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtVlanAllowedEntry

sub10EthMgmtVlanAllowedEntry		1.3.6.1.4.1.39003.4.2.2.8.1
An entry (row) in the sub10UnitMgmtVlanTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtVlanAllowedEntry

sub10EthMgmtVlanAllowedIndex		1.3.6.1.4.1.39003.4.2.2.8.1.1
The sub10EthMgmtVlanTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..60

sub10EthMgmtVlanAllowedRowStatus		1.3.6.1.4.1.39003.4.2.2.8.1.2
The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid with already consistent row objects this object must be set to active(1). If row objects are not yet set to consistent values the row status must first be set to createAndWait(5) after which the row status is set to 'notReady(3)'. When in the 'notReady(3)' state row objects can then be set to consistent values before row status can be set to active(1). To delete the row set this to destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sub10EthMgmtVlanAllowedId		1.3.6.1.4.1.39003.4.2.2.8.1.3
The vlan id which is allowed to pass through the ethernet interface. Duplicate vlan ids in multiple entries of the table with RowStatus 'active(1) are not allowed and any attempt to set a duplicate active entry will be rejected. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10VlanId

sub10EthMgmtQoSActiveState		1.3.6.1.4.1.39003.4.2.3.1
This defines if QoS is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthMgmtQoSMode		1.3.6.1.4.1.39003.4.2.3.2
Defines the mode of QoS action to be applied to the QoS queues. qosEthernet: - Traffic is mapped to QoS queues - based on Ethernet protocol - VLANId and/or PCP Bits. - See sub10EthMgmtQoSVlanMappingTable - and sub10EthMgmtQoSPCPMappingTable. qosIPMPLS: - Traffic is mapped to QoS queues - based on IP protocol - DSCP markings and/or MPLS traffic - classes. See sub10EthMgmtQoSDSCPMappingTable and sub10EthMgmtQoSMPLSMappingTable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	qosEthernet(1), qosIPMPLS(2)

sub10EthMgmtQoSUntaggedQueue		1.3.6.1.4.1.39003.4.2.3.3
This defines the QoS queue where all untagged ethernet frames are placed. Only valid when sub10EthMgmtQoSQType = 'qosEthernet' For tagged frames see sub10EthMgmtQoSVlanMappingTable and sub10EthMgmtQoSPCPMappingTable.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10QoSQueue

sub10EthMgmtQoSQTable		1.3.6.1.4.1.39003.4.2.3.4
This table configures the characteristics of a Quality of Service queue. There are a fixed number of 8 queues in total and therefore 8 entries in this table indexed 1 thru 8. The number of queue entries in the table is given by the value of sub10EthMgmtQoSQNumber.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtQoSQEntry

sub10EthMgmtQoSQEntry		1.3.6.1.4.1.39003.4.2.3.4.1
An entry (row) in the sub10EthMgmtQoSQTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtQoSQEntry

sub10EthMgmtQoSQIndex		1.3.6.1.4.1.39003.4.2.3.4.1.1
The queue number used as an index, fixed to 8 standard queues.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..8

sub10EthMgmtQoSQSchedulingType		1.3.6.1.4.1.39003.4.2.3.4.1.2
The scheduling discipline applied to the queue. qosSPQ - Strict Priority Queueing Queues are serviced in strict priority order. Packets on the queue are servicedd and transmitted until either the queue is empty or a packet is found in a higher queue, in the latter case the higher priority queue take precedence. Individual PCP (CoS) bits or DSCP markings in each packet are not observed within the queue and are not therefore transmitted first according to their relative priority. Instead it is possible to map certain VLANs, PCP bits and DSCP marking to certain queues to achieve priority transmission. The mapping of VLAN, PCP bits or DSCP markings to a specific queue are managed using tables : sub10EthMgmtQoSVlanTable sub10EthMgmtQoSPCPTable sub10EthMgmtQoSDSCPTable qosDWRR - Deficit Weighted Round Robin A weighting is allocated to each queue which defines the number of bytes that can be transmitted from that queue in a single visit of the scheduler. This is used to calculate a quantum which is the number of bytes that can always be transmitted in each visit of the scheduler. A deficit counter is also maintained across visits from the scheduler, at each visit the quantum is added to the deficit. This ensures that on average a queue that is not loaded to its intended capacity will utilise the calculated deficit at times when the queue is busy. At startup Deficit counter is initialised to zero. On each visit of the scheduler packets are transmitted according to the following rules... Deficit = Quantum + Deficit. while (Queue not empty and PktLength <= Deficit) Transmit Pkt Deficit = Deficit - PktLength Remaining Deficit is carried forward to the next visit of the scheduler. Effective behaviour of DWRR is as follows: 1. Available bandwidth is shared fairly when queues are not saturated 2. Lower priority saturated queues will transmit at their allocated service rate. 3. Any remaining bandwidth is shared amongst unsaturated queues. NB. In a mixed configuration where some queues are configured as Strict Priority (SP) and some configured as Deficit Weighted Round Robin (DWRR), then queues configured as SP should all be higher in scheduling priority than those configured as DWRR. This is to avoid the lower priority queues having transmission precedence over higher priority queues.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	qosSPQ(1), qosDWRR(2)

sub10EthMgmtQoSQDWRRWeight		1.3.6.1.4.1.39003.4.2.3.4.1.3
A percentage weighting factor used to calculate the quantum value used to calculate the starting transmission credit at each visit of the queue scheduler. Only for scheduling type Deficit Weighted Round Robin. sub10EthMgmtQoSQSchedulingType = 'qosDWRR' The weighting is calculated as the ratio of the transmit rate configured as a percentage. The internal implementation of DWRR will calculate the correct quantum based on total bandwidth available.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..100

sub10EthMgmtQoSQCongestionPolicy		1.3.6.1.4.1.39003.4.2.3.4.1.4
The policy used when a queue is congested.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	qosTailDrop(1)

sub10EthMgmtQoSQSizeMax		1.3.6.1.4.1.39003.4.2.3.4.1.5
The maximum size of the queue expressed in packets.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

sub10EthMgmtQoSQLen		1.3.6.1.4.1.39003.4.2.3.4.1.6
The current length of the queue expressed in packets.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

sub10EthMgmtQoSVlanMappingNumber		1.3.6.1.4.1.39003.4.2.3.5
The number of sub10EthMgmtQoSVlanMappingTable table entries present on this system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..100

sub10EthMgmtQoSVlanTable		1.3.6.1.4.1.39003.4.2.3.6
This table configures the Quality of Service Vlan to queue mapping. Multiple Vlans may be mapped to any queue. On egress of the ethernet interface all pkts tagged with the specific Vlan Id are inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSVlanNumber.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtQoSVlanEntry

sub10EthMgmtQoSVlanEntry		1.3.6.1.4.1.39003.4.2.3.6.1
An entry (row) in the sub10EthMgmtQoSVlanMappingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtQoSVlanEntry

sub10EthMgmtQoSVlanIndex		1.3.6.1.4.1.39003.4.2.3.6.1.1
The sub10EthMgmtQoSVlanMappingTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..16

sub10EthMgmtQoSVlanId		1.3.6.1.4.1.39003.4.2.3.6.1.2
The vlan id used as an index to the table and which is egressing through the ethernet interface and which should be placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10VlanId

sub10EthMgmtQoSVlanQueue		1.3.6.1.4.1.39003.4.2.3.6.1.3
The queue number which identifies the specific queue where the packets that are tagged with the Vlan Id specified in sub10EthMgmtQoSVlanId are inserted.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10QoSQueue

sub10EthMgmtQoSPCPTable		1.3.6.1.4.1.39003.4.2.3.8
This table configures the Quality of Service Priority Code Point (PCP) or Pbits to queue mapping. Multiple PCPs may be mapped to the same queue but the same PCP cannot be mapped to more than one queue. This table has a maximum size of 8 entries with exactly 1 entry per PCP bit. On egress of the ethernet interface all pkts tagged with the specific PCP bit (irrespective of its Vlan Id) is inserted on the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSPCPMappingNumber (maximum 8).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtQoSPCPEntry

sub10EthMgmtQoSPCPEntry		1.3.6.1.4.1.39003.4.2.3.8.1
An entry (row) in the sub10EthMgmtQoSPCPMappingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtQoSPCPEntry

sub10EthMgmtQoSPCPIndex		1.3.6.1.4.1.39003.4.2.3.8.1.1
The sub10EthMgmtQoSPCPTable index. This represents the PCP bits priority value. sub10EthMgmtQoSPCPIndex(1)=PCPBit(0) sub10EthMgmtQoSPCPIndex(2)=PCPBit(1) sub10EthMgmtQoSPCPIndex(3)=PCPBit(2) sub10EthMgmtQoSPCPIndex(4)=PCPBit(3) sub10EthMgmtQoSPCPIndex(5)=PCPBit(4) sub10EthMgmtQoSPCPIndex(6)=PCPBit(5) sub10EthMgmtQoSPCPIndex(7)=PCPBit(6) sub10EthMgmtQoSPCPIndex(8)=PCPBit(7)
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..8

sub10EthMgmtQoSPCPQueue		1.3.6.1.4.1.39003.4.2.3.8.1.2
The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific PCP bit sub10EthMgmtQoSPCPIndex are inserted. There are up to 8 queues.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10QoSQueue

sub10EthMgmtQoSDSCPMappingNumber		1.3.6.1.4.1.39003.4.2.3.9
The number of sub10EthMgmtQoSDSCPMappingTable table entries present on this system.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..64

sub10EthMgmtQoSDSCPTable		1.3.6.1.4.1.39003.4.2.3.10
This table configures the Quality of Service Differentiated Services Code Point (DSCP) to queue mapping. Multiple DSCPs may be mapped to the same queue but the same DSCP cannot be mapped to more than one queue. This table has a maximum size of 64 with 1 entry per DSCP value. On egress of the ethernet interface all pkts tagged with the specific DSCP marking in the IP header will be inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSDSCPMappingNumber (maximum 64).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtQoSDSCPEntry

sub10EthMgmtQoSDSCPEntry		1.3.6.1.4.1.39003.4.2.3.10.1
An entry (row) in the sub10EthMgmtQoSDSCPMappingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtQoSDSCPEntry

sub10EthMgmtQoSDSCPIndex		1.3.6.1.4.1.39003.4.2.3.10.1.1
The sub10EthMgmtQoSDSCPTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..64

sub10EthMgmtQoSDSCPMarking		1.3.6.1.4.1.39003.4.2.3.10.1.2
The DSCP value used as an index to the table. This defines the DSCP value which when egressing through the ethernet interface is placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..63

sub10EthMgmtQoSDSCPQueue		1.3.6.1.4.1.39003.4.2.3.10.1.3
The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific DSCP marking sub10EthMgmtQoSDSCP are inserted.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10QoSQueue

sub10EthMgmtQoSMPLSMappingNumber		1.3.6.1.4.1.39003.4.2.3.11
The number of sub10EthMgmtQoSMPLSMappingTable table entries present on this system.This is equivelent to the number of MPLS Traffic classes
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..64

sub10EthMgmtQoSMPLSTable		1.3.6.1.4.1.39003.4.2.3.12
This table configures the Quality of Service Multi-Protocol Label Switching protocol (MPLS) Traffic Class (TC) to queue mapping. Multiple MPLS TCs may be mapped to the same queue but the same MPLS TC cannot be mapped to more than one queue. This table has a maximum size of 64 with 1 entry per MPLS TC value. On egress of the ethernet interface all pkts tagged with the specific MPLS TC in the IP header will be inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSMPLSMappingNumber (maximum 8).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtQoSMPLSEntry

sub10EthMgmtQoSMPLSEntry		1.3.6.1.4.1.39003.4.2.3.12.1
An entry (row) in the sub10EthMgmtQoSMPLSMappingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtQoSMPLSEntry

sub10EthMgmtQoSMPLSIndex		1.3.6.1.4.1.39003.4.2.3.12.1.1
The sub10EthMgmtQoSMPLSMappingTable index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..8

sub10EthMgmtQoSMPLSTrafficClass		1.3.6.1.4.1.39003.4.2.3.12.1.2
The MPLS Traffic Class value used as an index to the table. This defines the MPLS TC value which when egressing through the ethernet interface is placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..7

sub10EthMgmtQoSMPLSQueue		1.3.6.1.4.1.39003.4.2.3.12.1.3
The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific MPLS Traffic Class sub10EthMgmtQoSMPLSTrafficClass are inserted.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10QoSQueue

sub10EthMgmtStatsActiveTable		1.3.6.1.4.1.39003.4.2.4.1
This table maintains an entry for each Ethernet statistic that is enabled and active.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthMgmtStatsActiveEntry

sub10EthMgmtStatsActiveEntry		1.3.6.1.4.1.39003.4.2.4.1.1
An entry in the sub10EthMgmtStatsActiveTable. Each entry represents an object instance of ethernet stats and it's current state.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthMgmtStatsActiveEntry

sub10EthMgmtStatsActiveIndex		1.3.6.1.4.1.39003.4.2.4.1.1.1
The number of ethernet stats objects used as an index to this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..30

sub10EthMgmtStatsActiveName		1.3.6.1.4.1.39003.4.2.4.1.1.2
The stats object name. This is the name of the ethernet stats object in the sub10EthernetStatsCurrent group.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10EthMgmtStatsActiveState		1.3.6.1.4.1.39003.4.2.4.1.1.3
If set to 'enabled' the statistic is active.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10EthStatsTimeElapsed		1.3.6.1.4.1.39003.4.3.1
The time that has elapsed from the beginning of the statistical measurement period. This is normally time from just after the last reboot time when the statistics module begins it's calculations. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10EthernetStatsCurrTable		1.3.6.1.4.1.39003.4.3.2.1
This table defines the current stats objects of the ethernet interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthernetStatsCurrEntry

sub10EthernetStatsCurrEntry		1.3.6.1.4.1.39003.4.3.2.1.1
An entry (row) in the sub10EthernetStatsCurrTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthernetStatsCurrEntry

sub10EthStatsCurrRxOctets		1.3.6.1.4.1.39003.4.3.2.1.1.1
The number of octets received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxGoodFrms		1.3.6.1.4.1.39003.4.3.2.1.1.2
The number of good frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxBcastFrms		1.3.6.1.4.1.39003.4.3.2.1.1.3
The number of broadcast frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxMcastFrms		1.3.6.1.4.1.39003.4.3.2.1.1.4
The number of multicast frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxPauseFrms		1.3.6.1.4.1.39003.4.3.2.1.1.5
The number of Pause frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxCRCErrs		1.3.6.1.4.1.39003.4.3.2.1.1.6
The number of CRC errors received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxAlignErrs		1.3.6.1.4.1.39003.4.3.2.1.1.7
The number of Alignment coding errors received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxOversized		1.3.6.1.4.1.39003.4.3.2.1.1.8
The number of Oversized frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxJabberFrms		1.3.6.1.4.1.39003.4.3.2.1.1.9
The number of Jabber frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxUndersized		1.3.6.1.4.1.39003.4.3.2.1.1.10
The number of Undersized frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxFragments		1.3.6.1.4.1.39003.4.3.2.1.1.11
The number of frame fragments received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxSOFOvrns		1.3.6.1.4.1.39003.4.3.2.1.1.12
The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxOctets		1.3.6.1.4.1.39003.4.3.2.1.1.13
The number of octets transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxGoodFrms		1.3.6.1.4.1.39003.4.3.2.1.1.14
The number of ethernet frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxBcastFrms		1.3.6.1.4.1.39003.4.3.2.1.1.15
The number of broadcast frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxMcastFrms		1.3.6.1.4.1.39003.4.3.2.1.1.16
The number of multicast frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxPauseFrms		1.3.6.1.4.1.39003.4.3.2.1.1.17
The number of Pause frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxDeferred		1.3.6.1.4.1.39003.4.3.2.1.1.18
The number of Deferred frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxCollsn		1.3.6.1.4.1.39003.4.3.2.1.1.19
The number of Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxSnglCollsn		1.3.6.1.4.1.39003.4.3.2.1.1.20
The number of Single Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxMlplCollsn		1.3.6.1.4.1.39003.4.3.2.1.1.21
The number of Multiple Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxExsvCollsn		1.3.6.1.4.1.39003.4.3.2.1.1.22
The number of Excessive Collision for which transmission was abandoned over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxLtCollsn		1.3.6.1.4.1.39003.4.3.2.1.1.23
The number of Late Collision for which transmission was abandoned over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrTxCSenseErrs		1.3.6.1.4.1.39003.4.3.2.1.1.24
The number of Carrier Sense Errored frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts64Octets		1.3.6.1.4.1.39003.4.3.2.1.1.25
The total number of 64-byte frames received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts65T127		1.3.6.1.4.1.39003.4.3.2.1.1.26
The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts128T255		1.3.6.1.4.1.39003.4.3.2.1.1.27
The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts256T511		1.3.6.1.4.1.39003.4.3.2.1.1.28
The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts512T1023		1.3.6.1.4.1.39003.4.3.2.1.1.29
The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrPkts1024TMax		1.3.6.1.4.1.39003.4.3.2.1.1.30
The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10EthStatsCurrRxMbps		1.3.6.1.4.1.39003.4.3.2.1.1.31
The Rx throughput in Mbps in this second.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrTxMbps		1.3.6.1.4.1.39003.4.3.2.1.1.32
The Tx throughput in Mbps in this second.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrRxMbpsMin		1.3.6.1.4.1.39003.4.3.2.1.1.33
The minimum Rx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrRxMbpsMax		1.3.6.1.4.1.39003.4.3.2.1.1.34
The maximum Rx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrRxMbpsAvg		1.3.6.1.4.1.39003.4.3.2.1.1.35
The average Rx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrTxMbpsMin		1.3.6.1.4.1.39003.4.3.2.1.1.36
The minimum Tx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrTxMbpsMax		1.3.6.1.4.1.39003.4.3.2.1.1.37
The maximum Tx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrTxMbpsAvg		1.3.6.1.4.1.39003.4.3.2.1.1.38
The average Tx throughput in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrRmtRxMbpsAvg		1.3.6.1.4.1.39003.4.3.2.1.1.39
The average Rx throughput of the remote unit in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStatsCurrRmtTxMbpsAvg		1.3.6.1.4.1.39003.4.3.2.1.1.40
The average Tx throughput of the remote unit in Mbps in the last rolling minute.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistIntvls		1.3.6.1.4.1.39003.4.3.3.1.1
The number of valid table entries in sub10EthStats15mHistTable on this system. There is one entry per 15 minute interval. If the unit has been running for a minimum of 24 hours and collecting valid data then the number of entries will be 96, this represents a total maximum of 24 hours worth of data.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..96

sub10EthStats15mHistTable		1.3.6.1.4.1.39003.4.3.3.1.2
This table maintains a history of Ethernet statistics based on 15 minute intervals. There are a maximum of 96 intervals which represent 24 hours of data. This table along with the 1m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 15 minute interval where each interval is synchronised to the clock on the hour. There are up to 96 intervals starting at 1. The number of valid entries in the table is given by the value of sub10EthStats15mHistIntvls of which the minimum is 0 and the maximum is 96 therefore providing up to a maximum of 24 hours of 15 minute interval data. The first entry indexed by 1 represents the most recent completed 15 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 96 then the least recent interval entry is summarised into 24 hour stats and then discarded.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthStats15mHistEntry

sub10EthStats15mHistEntry		1.3.6.1.4.1.39003.4.3.3.1.2.1
An entry in the sub10EthStats15mHistTable. Each entry represents 15 minute of performance management data where the first entry with index=1 is the most recent 15 minute interval and the last entry with index=n (up to 96) is the least recent 15 minute interval. The number of valid intervals is sub10EthStats15mHistIntvls.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthStats15mHistEntry

sub10EthStats15mHistIntvl		1.3.6.1.4.1.39003.4.3.3.1.2.1.1
The interval number used as an index to this table. Interval numbers start at 1 (the most recent 15 minute interval) and have a maximum value of 96 (the least recent 15 minute interval).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..96

sub10EthStats15mHistTime		1.3.6.1.4.1.39003.4.3.3.1.2.1.2
The local system time when this 15m history entry was created. This represents the end of the 15 minute interval for which the associated stats with the same sub10EthStats15mHistIntvl table index are relevant.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10EthStats15mHistRxOctets		1.3.6.1.4.1.39003.4.3.3.1.2.1.3
The number of octets received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxGoodFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.4
The number of good frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxBcastFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.5
The number of broadcast frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxMcastFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.6
The number of multicast frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxPauseFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.7
The number of Pause frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxCRCErrs		1.3.6.1.4.1.39003.4.3.3.1.2.1.8
The number of CRC errors received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxAlignErrs		1.3.6.1.4.1.39003.4.3.3.1.2.1.9
The number of Alignment coding errors received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxOversized		1.3.6.1.4.1.39003.4.3.3.1.2.1.10
The number of Oversized frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxJabberFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.11
The number of Jabber frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxUndersized		1.3.6.1.4.1.39003.4.3.3.1.2.1.12
The number of Undersized frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxFragments		1.3.6.1.4.1.39003.4.3.3.1.2.1.13
The number of frame fragments received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxSOFOvrns		1.3.6.1.4.1.39003.4.3.3.1.2.1.14
The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxOctets		1.3.6.1.4.1.39003.4.3.3.1.2.1.15
The number of octets transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxGoodFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.16
The number of ethernet frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxBcastFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.17
The number of broadcast frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxMcastFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.18
The number of multicast frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxPauseFrms		1.3.6.1.4.1.39003.4.3.3.1.2.1.19
The number of Pause frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxDeferred		1.3.6.1.4.1.39003.4.3.3.1.2.1.20
The number of Deferred frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxCollsn		1.3.6.1.4.1.39003.4.3.3.1.2.1.21
The number of Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxSnglCollsn		1.3.6.1.4.1.39003.4.3.3.1.2.1.22
The number of Single Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxMlplCollsn		1.3.6.1.4.1.39003.4.3.3.1.2.1.23
The number of Multiple Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxExsvCollsn		1.3.6.1.4.1.39003.4.3.3.1.2.1.24
The number of Excessive Collision for which transmission was abandoned over the Ethernet interface in this 1 minute interval. 5 For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxLtCollsn		1.3.6.1.4.1.39003.4.3.3.1.2.1.25
The number of Late Collision for which transmission was abandoned over the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistTxCSenseErrs		1.3.6.1.4.1.39003.4.3.3.1.2.1.26
The number of Carrier Sense Errored frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts64Octets		1.3.6.1.4.1.39003.4.3.3.1.2.1.27
The total number of 64-byte frames received and transmitted on the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts65T127		1.3.6.1.4.1.39003.4.3.3.1.2.1.28
The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts128T255		1.3.6.1.4.1.39003.4.3.3.1.2.1.29
The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts256T511		1.3.6.1.4.1.39003.4.3.3.1.2.1.30
The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts512T1023		1.3.6.1.4.1.39003.4.3.3.1.2.1.31
The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistPkts1024TMax		1.3.6.1.4.1.39003.4.3.3.1.2.1.32
The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats15mHistRxMbpsMin		1.3.6.1.4.1.39003.4.3.3.1.2.1.33
The minimum Rx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistRxMbpsMax		1.3.6.1.4.1.39003.4.3.3.1.2.1.34
The maximum Rx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistRxMbpsAvg		1.3.6.1.4.1.39003.4.3.3.1.2.1.35
The average Rx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistTxMbpsMin		1.3.6.1.4.1.39003.4.3.3.1.2.1.36
The minimum Tx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistTxMbpsMax		1.3.6.1.4.1.39003.4.3.3.1.2.1.37
The maximum Tx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats15mHistTxMbpsAvg		1.3.6.1.4.1.39003.4.3.3.1.2.1.38
The average Tx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistIntvls		1.3.6.1.4.1.39003.4.3.3.2.1
The number of valid table entries in sub10EthStats1dHistTable on this system. There is one entry per 1 day interval. If the unit has been running for a minimum of 30 days and collecting valid data then the number of entries will be 30, this represents a total maximum of 30 days worth of data.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..30

sub10EthStats1dHistTable		1.3.6.1.4.1.39003.4.3.3.2.2
This table maintains a history of Radio statistics based on 1 day intervals. There are a maximum of 30 intervals which represent 30 days of data. This table along with the 1m and 15m tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 day interval where each interval is synchronised to the clock on the hour. There are up to 30 intervals starting at 1. The number of valid entries in the table is given by the value of sub10EthStats1dHistIntvls of which the minimum is 0 and the maximum is 30 therefore providing up to a maximum of 30 days of 1 day interval data. The first entry indexed by 1 represents the most recent completed 1 day interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 30 then the least recent interval entry is discarded.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10EthStats1dHistEntry

sub10EthStats1dHistEntry		1.3.6.1.4.1.39003.4.3.3.2.2.1
An entry in the sub10EthStats1dHistTable. Each entry represents 1 day of performance management data where the first entry with index=1 is the most recent 1 day interval and the last entry with index=n (up to 30) is the least recent 1 day interval. The number of valid intervals is given by the value of sub10EthStats1dHistIntvls.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10EthStats1dHistEntry

sub10EthStats1dHistIntvl		1.3.6.1.4.1.39003.4.3.3.2.2.1.1
The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 day interval) and have a maximum value of 30 (the least recent 1 day interval).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..30

sub10EthStats1dHistTime		1.3.6.1.4.1.39003.4.3.3.2.2.1.2
The local system time when this 1d history entry was created. This represents the end of the 1 day interval for which the associated stats with the same sub10EthStats1dHistIntvl table index are relevant.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10EthStats1dHistRxOctets		1.3.6.1.4.1.39003.4.3.3.2.2.1.3
The number of octets received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxGoodFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.4
The number of good frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxBcastFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.5
The number of broadcast frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxMcastFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.6
The number of multicast frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxPauseFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.7
The number of Pause frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxCRCErrs		1.3.6.1.4.1.39003.4.3.3.2.2.1.8
The number of CRC errors received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxAlignErrs		1.3.6.1.4.1.39003.4.3.3.2.2.1.9
The number of Alignment coding errors received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxOversized		1.3.6.1.4.1.39003.4.3.3.2.2.1.10
The number of Oversized frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxJabberFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.11
The number of Jabber frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxUndersized		1.3.6.1.4.1.39003.4.3.3.2.2.1.12
The number of Undersized frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxFragments		1.3.6.1.4.1.39003.4.3.3.2.2.1.13
The number of frame fragments received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxSOFOvrns		1.3.6.1.4.1.39003.4.3.3.2.2.1.14
The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxOctets		1.3.6.1.4.1.39003.4.3.3.2.2.1.15
The number of octets transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxGoodFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.16
The number of ethernet frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxBcastFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.17
The number of broadcast frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxMcastFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.18
The number of multicast frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxPauseFrms		1.3.6.1.4.1.39003.4.3.3.2.2.1.19
The number of Pause frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxDeferred		1.3.6.1.4.1.39003.4.3.3.2.2.1.20
The number of Deferred frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxCollsn		1.3.6.1.4.1.39003.4.3.3.2.2.1.21
The number of Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxSnglCollsn		1.3.6.1.4.1.39003.4.3.3.2.2.1.22
The number of Single Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxMlplCollsn		1.3.6.1.4.1.39003.4.3.3.2.2.1.23
The number of Multiple Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxExsvCollsn		1.3.6.1.4.1.39003.4.3.3.2.2.1.24
The number of Excessive Collision for which transmission was abandoned over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxLtCollsn		1.3.6.1.4.1.39003.4.3.3.2.2.1.25
The number of Late Collision for which transmission was abandoned over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistTxCSenseErrs		1.3.6.1.4.1.39003.4.3.3.2.2.1.26
The number of Carrier Sense Errored frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts64Octets		1.3.6.1.4.1.39003.4.3.3.2.2.1.27
The total number of 64-byte frames received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts65T127		1.3.6.1.4.1.39003.4.3.3.2.2.1.28
The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts128T255		1.3.6.1.4.1.39003.4.3.3.2.2.1.29
The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts256T511		1.3.6.1.4.1.39003.4.3.3.2.2.1.30
The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts512T1023		1.3.6.1.4.1.39003.4.3.3.2.2.1.31
The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistPkts1024TMax		1.3.6.1.4.1.39003.4.3.3.2.2.1.32
The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10EthStats1dHistRxMbpsMin		1.3.6.1.4.1.39003.4.3.3.2.2.1.33
The minimum Rx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistRxMbpsMax		1.3.6.1.4.1.39003.4.3.3.2.2.1.34
The maximum Rx throughput in Mbps in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistRxMbpsAvg		1.3.6.1.4.1.39003.4.3.3.2.2.1.35
The average Rx throughput in Mbps in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistTxMbpsMin		1.3.6.1.4.1.39003.4.3.3.2.2.1.36
The minimum Tx throughput in Mbps in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistTxMbpsMax		1.3.6.1.4.1.39003.4.3.3.2.2.1.37
The maximum Tx throughput in Mbps in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10EthStats1dHistTxMbpsAvg		1.3.6.1.4.1.39003.4.3.3.2.2.1.38
The average Tx throughput in Mbps in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ThroughputMbps

sub10RadioLclLinkStatus		1.3.6.1.4.1.39003.5.1.1.1
The status of the local radio link.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10RadioLinkState

sub10RadioLclTxPower		1.3.6.1.4.1.39003.5.1.1.2
The current transmit power of the local radio link, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-30..30

sub10RadioLclRxPower		1.3.6.1.4.1.39003.5.1.1.3
The current receive power of the local radio link, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioLclVectErr		1.3.6.1.4.1.39003.5.1.1.4
The current vector error of the local radio link, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioLclLnkLoss		1.3.6.1.4.1.39003.5.1.1.5
The current link loss of the local radio link, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioLclAlignmentMode		1.3.6.1.4.1.39003.5.1.1.6
Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). The alignment mode is managed using sub10RadioMgmtAlignmentMode.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10AlignmentMode

sub10RadioLclDataRate		1.3.6.1.4.1.39003.5.1.1.7
The maximum data rate of the Airside interface.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10RadioDataRate

sub10RadioLclMWUType		1.3.6.1.4.1.39003.5.1.1.8
The local MWU type
Status: current	Access: read-only
OBJECT-TYPE
	Sub10MWUType

sub10RadioLclAFER		1.3.6.1.4.1.39003.5.1.1.9
The Air Frame Error Ratio in the last second. This is the % of lost air frames based on the UFEC count in the previous second divided by the expected Air Frame Rate(AFR) in 1 second.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioLclRxModulationMode		1.3.6.1.4.1.39003.5.1.1.10
The current Receive Modulation Mode on the local unit.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ModulationMode

sub10RadioLclTxModulationMode		1.3.6.1.4.1.39003.5.1.1.11
The current Transmit Modulation Mode on the local unit.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10ModulationMode

sub10RadioRmtLinkStatus		1.3.6.1.4.1.39003.5.1.2.1
The status of the remote radio link.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10RadioLinkState

sub10RadioRmtTxPower		1.3.6.1.4.1.39003.5.1.2.2
The current transmit power of the remote radio link, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioRmtRxPower		1.3.6.1.4.1.39003.5.1.2.3
The current receive power of the remote radio link, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioRmtVectErr		1.3.6.1.4.1.39003.5.1.2.4
The current vector error of the remote radio link, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioRmtLnkLoss		1.3.6.1.4.1.39003.5.1.2.5
The current link loss of the remote radio link, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioRmtAlignmentMode		1.3.6.1.4.1.39003.5.1.2.7
The remote radio unit's Alignment mode. Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0).
Status: current	Access: read-only
OBJECT-TYPE
	Sub10AlignmentMode

sub10RadioRmtAFER		1.3.6.1.4.1.39003.5.1.2.8
The remote unit Air Frame Error Ratio in this second. This is the % of lost air frames based on the UFEC count in the previous second divided by the expected Air Frame Rate(AFR) in 1 second.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioMgmtTxPowerLimit		1.3.6.1.4.1.39003.5.2.1
The configured transmit power of radio link. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10TxPowerLimit

sub10RadioMgmtTxRxFreq		1.3.6.1.4.1.39003.5.2.2
The configured TX/RX frequency pairs of radio link. Each enumerated option represents the TX and RX frequency pair settings in MHz. Options are available for E-Band at channel width 250MHz and 500MHz and E-Band channel width 500MHz. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	e250Tx71250Rx81250(0), e250Tx71500Rx81500(1), e250Tx71750Rx81750(2), e250Tx72000Rx82000(3), e250Tx72250Rx82250(4), e250Tx72500Rx82500(5), e250Tx72750Rx82750(6), e250Tx73000Rx83000(7), e250Tx73250Rx83250(8), e250Tx73500Rx83500(9), e250Tx73750Rx83750(10), e250Tx74000Rx84000(11), e250Tx74250Rx84250(12), e250Tx74500Rx84500(13), e250Tx74750Rx84750(14), e250Tx75000Rx85000(15), e250Tx75250Rx85250(16), e250Tx75500Rx85500(17), e250Tx75750Rx85750(18), e500Tx72375Rx82375(19), e500Tx72625Rx82625(20), e500Tx72875Rx82875(21), e500Tx73125Rx83125(22), e500Tx73375Rx83375(23), e500Tx73625Rx83625(24), e500Tx73875Rx83875(25), e500Tx74125Rx84125(26), e500Tx74375Rx84375(27), e500Tx74625Rx84625(28), v500Tx58500Rx61500(29), v500Tx58500Rx62000(30), v500Tx58500Rx62500(31), v500Tx59000Rx61500(32), v500Tx59000Rx62000(33), v500Tx59000Rx62500(34), v500Tx59500Rx61500(35), v500Tx59500Rx62000(36), v500Tx59500Rx62500(37)

sub10RadioMgmtAPCMode		1.3.6.1.4.1.39003.5.2.3
Automatic Transmit Power Control. The initial setting of transmit power used is defined by sub10RadioMgmtTxPower. If sub10RadioMgmtAPCMode is enabled then the transmit power may then vary according to the RSSI measured from the remote end of the link. The actual transmit power is readable in sub10RadioLclTxPower at the local end and sub10RadioRmtTxPower at the remote end of the link. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	apcModeDisabled(0), apcModeVariable(1), apcModeFixed(2)

sub10RadioMgmtModulationMode		1.3.6.1.4.1.39003.5.2.4
Set the highest order Modulation Mode attempted by Adaptive Modulation. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	Sub10ModulationMode

sub10RadioMgmtAmod		1.3.6.1.4.1.39003.5.2.5
Adaptive Modulation mode.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10RadioMgmtAlignmentMode		1.3.6.1.4.1.39003.5.2.6
Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). The alignment mode can be manually changed by setting this object.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10AlignmentMode

sub10RadioMgmtMWUChannelWidth		1.3.6.1.4.1.39003.5.2.8
MWU Channel width. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	channelWidth250(0), channelWidth500(1)

sub10RadioMgmtDataRate		1.3.6.1.4.1.39003.5.2.10
The maximum data rate of the Airside interface up to the licensed value.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10RadioDataRate

sub10RadioMgmtStats1dPersist		1.3.6.1.4.1.39003.5.2.9.1
If set to 'stateEnabled(1) the sub10RadioStats1dHistTable objects are stored and read in on startup. This makes the history non-volatile across unit resets.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10RadioMgmtStatsActiveTable		1.3.6.1.4.1.39003.5.2.9.4
This table maintains an entry for each Radio statistic that is enabled and active.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10RadioMgmtStatsActiveEntry

sub10RadioMgmtStatsActiveEntry		1.3.6.1.4.1.39003.5.2.9.4.1
An entry in the sub10RadioMgmtStatsActiveTable. Each entry represents an object instance of Radio stats and it's current state.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10RadioMgmtStatsActiveEntry

sub10RadioMgmtStatsActiveIndex		1.3.6.1.4.1.39003.5.2.9.4.1.1
The number of Radio stats objects used as an index to this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..29

sub10RadioMgmtStatsActiveName		1.3.6.1.4.1.39003.5.2.9.4.1.2
The stats object name. This is the name of the ethernet stats object in the sub10RadioStatsCurrent group.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..22)

sub10RadioMgmtStatsActiveState		1.3.6.1.4.1.39003.5.2.9.4.1.3
If set to 'enabled' the statistic is active.
Status: current	Access: read-write
OBJECT-TYPE
	Sub10State

sub10RadioStatsTimeElapsed		1.3.6.1.4.1.39003.5.3.1
The time that has elapsed from the beginning of the statistical measurement period. This is normally time from just after the last reboot time when the statistics module begins it's calculations. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrTxPowerMin		1.3.6.1.4.1.39003.5.3.2.1
The minimum value that the transmit power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrTxPowerMax		1.3.6.1.4.1.39003.5.3.2.2
The maximum value that the transmit power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrTxPowerAvg		1.3.6.1.4.1.39003.5.3.2.3
The average value of the transmit power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrRxPowerMin		1.3.6.1.4.1.39003.5.3.2.4
The minimum value that the receive power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRxPowerMax		1.3.6.1.4.1.39003.5.3.2.5
The maximum value that the receive power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRxPowerAvg		1.3.6.1.4.1.39003.5.3.2.6
The average value of the receive power of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrVectErrMin		1.3.6.1.4.1.39003.5.3.2.7
The minimum value that the vector error of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrVectErrMax		1.3.6.1.4.1.39003.5.3.2.8
The maximum value that the vector error of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrVectErrAvg		1.3.6.1.4.1.39003.5.3.2.9
The average value of the vector error of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrLnkLossMin		1.3.6.1.4.1.39003.5.3.2.10
The minimum value that the link loss of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrLnkLossMax		1.3.6.1.4.1.39003.5.3.2.11
The maximum value that the link loss of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrLnkLossAvg		1.3.6.1.4.1.39003.5.3.2.12
The average value of the link loss of the local radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRxFrms		1.3.6.1.4.1.39003.5.3.2.13
The number of Airside frames received over the Radio interface. This is irrespective of whether the Airside frame transmitted contained any ethernet data. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrTxFrms		1.3.6.1.4.1.39003.5.3.2.14
The number of Airside frames transmitted over the Radio interface. This is irrespective of whether the Airside frame transmitted contained any ethernet data. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrRxPkts		1.3.6.1.4.1.39003.5.3.2.15
The number of Ethernet packets received over the Radio interface. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrTxPkts		1.3.6.1.4.1.39003.5.3.2.16
The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface. This does not include packets originating from the management sub-system. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrRxMgmtPkts		1.3.6.1.4.1.39003.5.3.2.17
The number of Ethernet packets received over the Radio interface and which are destined for the management sub-system on this unit. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrTxMgmtPkts		1.3.6.1.4.1.39003.5.3.2.18
The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system. This does not include packets originating from the Ethernet interface. Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrRxBadFrms		1.3.6.1.4.1.39003.5.3.2.19
The count of bad frames detected on the receive side of the Radio interface. A bad frame could be caused by any one of the following detected errors: UFEC Error Header CRC Error Frame CRC Error Bad header Set to zero on unit reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrMWUTempMin		1.3.6.1.4.1.39003.5.3.2.24
The minimum MWU temperature measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrMWUTempMax		1.3.6.1.4.1.39003.5.3.2.25
The maximum MWU temperature measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrMWUTempAvg		1.3.6.1.4.1.39003.5.3.2.26
The average MWU temperature measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrQPSKTo8PSK		1.3.6.1.4.1.39003.5.3.2.27
The number transitions of Modulation Mode configuration from QPSK to 8PSK since unit reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStatsCurr8PSKToQPSK		1.3.6.1.4.1.39003.5.3.2.28
The number transitions of Modulation Mode configuration from 8PSK to QPSK since unit reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStatsCurrAFERMin		1.3.6.1.4.1.39003.5.3.2.29
The minimum AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrAFERMax		1.3.6.1.4.1.39003.5.3.2.30
The maximum AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrAFERAvg		1.3.6.1.4.1.39003.5.3.2.31
The average AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRmtTxPowerAvg		1.3.6.1.4.1.39003.5.3.2.32
The average value of the transmit power of the remote radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrRmtRxPowerAvg		1.3.6.1.4.1.39003.5.3.2.33
The average value of the receive power of the remote radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRmtVectErrAvg		1.3.6.1.4.1.39003.5.3.2.34
The average value of the vector error of the remote radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRmtLnkLossAvg		1.3.6.1.4.1.39003.5.3.2.35
The average value of the link loss of the remote radio link measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRmtMWUTempAvg		1.3.6.1.4.1.39003.5.3.2.36
The average MWU temperature of the remote unit measured over the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStatsCurrRmtAFERAvg		1.3.6.1.4.1.39003.5.3.2.37
The average AFER (Air Frame Error Ratio) of the remote unit in the previous rolling 60 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStatsCurrRxQPSK		1.3.6.1.4.1.39003.5.3.2.38
The time in seconds that Rx modulation mode has been in QPSK since last reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrRx8PSK		1.3.6.1.4.1.39003.5.3.2.39
The time in seconds that Rx modulation mode has been in 8PSK since last reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrTxQPSK		1.3.6.1.4.1.39003.5.3.2.40
The time in seconds that Txmodulation mode has been in QPSK since last reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStatsCurrTx8PSK		1.3.6.1.4.1.39003.5.3.2.41
The time in seconds that Tx modulation mode has been in 8PSK since last reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistIntvls		1.3.6.1.4.1.39003.5.3.3.1.1
The number of valid table entries in sub10RadioStats1mHistTable on this system. There is one entry per 1 minute interval. If the unit has been running for a minimum of 15 minutes and collecting valid data then the number of entries will be 15, this represents a total maximum of 5 minutes worth of data.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..60

sub10RadioStats1mHistTable		1.3.6.1.4.1.39003.5.3.3.1.2
This table maintains a history of Radio statistics based on 1 minute intervals. There are a maximum of 60 intervals which represent 1 hour of data. This table along with the 15m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 minute interval where each interval is synchronised to the clock on the hour. There are up to 60 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats1mHistIntvls of which the minimum is 0 and the maximum is 60 therefore providing up to a maximum of 60 minutes of 1 minute interval data. The first entry indexed by 1 represents the most recent completed 1 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is at least 15 then these 15 intervals are summarised into 15 minutes stats. At the end of a 60 minute period the least recent interval is discarded to accomodate the next minute interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10RadioStats1mHistEntry

sub10RadioStats1mHistEntry		1.3.6.1.4.1.39003.5.3.3.1.2.1
An entry in the sub10RadioStats1mHistTable. Each entry represents 1 minute of performance management data where the first entry with index=1 is the most recent 1 minute interval and the last entry with index=n (up to 60) is the least recent 1 minute interval. The number of valid intervals is given by the value of sub10RadioStats1mHistIntvls.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10RadioStats1mHistEntry

sub10RadioStats1mHistIntvl		1.3.6.1.4.1.39003.5.3.3.1.2.1.1
The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 minute interval) and have a maximum value of 60 (the least recent 1 minute interval).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..60

sub10RadioStats1mHistTime		1.3.6.1.4.1.39003.5.3.3.1.2.1.2
The local system time when this 1m history entry was created. This represents the end of the 1 minute interval for which the associated stats with the same sub10RadioStats1mHistIntvl table index are relevant.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10RadioStats1mHistTxPowerMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.3
The minimum value that the transmit power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistTxPowerMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.4
The maximum value that the transmit power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistTxPowerAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.5
The average value that the transmit power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistRxPowerMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.6
The minimum value that the receive power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistRxPowerMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.7
The maximum value that the receive power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistRxPowerAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.8
The average value that the receive power of the local radio link has reached in this minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistVectErrMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.9
The minimum value that the vector error of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistVectErrMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.10
The maximum value that the vector error of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistVectErrAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.11
The average value that the vector error of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistLnkLossMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.12
The minimum value that the link loss of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistLnkLossMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.13
The maximum value that the link loss of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistLnkLossAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.14
The average value that the link loss of the local radio link has reached in this minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistMWUTempMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.15
The minimum MWU temperature measured in this minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistMWUTempMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.16
The maximum MWU temperature measured in this minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistMWUTempAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.17
The average MWU temperature measured in this minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1mHistRxFrms		1.3.6.1.4.1.39003.5.3.3.1.2.1.22
The number of Airside frames received over the Radio interface in this minute. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistTxFrms		1.3.6.1.4.1.39003.5.3.3.1.2.1.23
The number of Airside frames transmitted over the Radio interface in this minute. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistRxPkts		1.3.6.1.4.1.39003.5.3.3.1.2.1.24
The number of Ethernet packets received over the Radio interface in this minute. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistTxPkts		1.3.6.1.4.1.39003.5.3.3.1.2.1.25
The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this minute. This does not include packets originating from the management sub-system.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistRxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.1.2.1.26
The number of Ethernet packets received over the Radio interface in this minute and which are destined for the management sub-system on this unit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistTxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.1.2.1.27
The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this minute. This does not include packets originating from the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistRxBadFrms		1.3.6.1.4.1.39003.5.3.3.1.2.1.28
The count of bad frames detected on the receive side of the Radio interface in this minute.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1mHistQPSKTo8PSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.29
The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1mHist8PSKToQPSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.30
The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1mHistAFERMin		1.3.6.1.4.1.39003.5.3.3.1.2.1.31
The minimum AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistAFERMax		1.3.6.1.4.1.39003.5.3.3.1.2.1.32
The maximum AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistAFERAvg		1.3.6.1.4.1.39003.5.3.3.1.2.1.33
The average AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1mHistRxQPSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.34
The time in seconds that the Rx Modulation Mode was QPSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1mHistRx8PSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.35
The time in seconds that the Rx Modulation Mode was 8PSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1mHistTxQPSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.36
The time in seconds that the Tx Modulation Mode was QPSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1mHistTx8PSK		1.3.6.1.4.1.39003.5.3.3.1.2.1.37
The time in seconds that the Tx Modulation Mode was 8PSK in this 1 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHistIntvls		1.3.6.1.4.1.39003.5.3.3.2.1
The number of valid table entries in sub10RadioStats15mHistTable on this system. There is one entry per 15 minute interval. If the unit has been running for a minimum of 24 hours and collecting valid data then the number of entries will be 96, this represents a total maximum of 24 hours worth of data.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..96

sub10RadioStats15mHistTable		1.3.6.1.4.1.39003.5.3.3.2.2
This table maintains a history of Radio statistics based on 15 minute intervals. There are a maximum of 96 intervals which represent 24 hours of data. This table along with the 1m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 15 minute interval where each interval is synchronised to the clock on the hour. There are up to 96 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats15mHistIntvls of which the minimum is 0 and the maximum is 96 therefore providing up to a maximum of 24 hours of 15 minute interval data. The first entry indexed by 1 represents the most recent completed 15 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 96 then the least recent interval entry is summarised into 24 hour stats and then discarded.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10RadioStats15mHistEntry

sub10RadioStats15mHistEntry		1.3.6.1.4.1.39003.5.3.3.2.2.1
An entry in the sub10RadioStats15mHistTable. Each entry represents 15 minutes performance management data where the first entry with index=1 is the most recent 15 minute interval and the last entry with index=n (up to 96) is the least recent 15 minute interval. The number of valid intervals is sub10RadioStats15mHistIntvls.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10RadioStats15mHistEntry

sub10RadioStats15mHistIntvl		1.3.6.1.4.1.39003.5.3.3.2.2.1.1
The interval number used as an index to this table. Interval numbers start at 1 (the most recent 15 minute interval) and have a maximum value of 96 (the least recent 15 minute interval).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..96

sub10RadioStats15mHistTime		1.3.6.1.4.1.39003.5.3.3.2.2.1.2
The local system time when this 15m history entry was created. This represents the end of the 15 minute interval for which the associated stats with the same sub10RadioStats15mHistIntvl table index are relevant.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10RadioStats15mHistTxPowerMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.3
The minimum value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistTxPowerMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.4
The maximum value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistTxPowerAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.5
The average value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistRxPowerMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.6
The minimum value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistRxPowerMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.7
The maximum value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistRxPowerAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.8
The average value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistVectErrMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.9
The minimum value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistVectErrMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.10
The maximum value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistVectErrAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.11
The average value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistLnkLossMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.12
The minimum value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistLnkLossMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.13
The maximum value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistLnkLossAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.14
The average value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistMWUTempMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.15
The minimum MWU temperature measured in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistMWUTempMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.16
The maximum MWU temperature measured in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistMWUTempAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.17
The average MWU temperature measured in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats15mHistRxFrms		1.3.6.1.4.1.39003.5.3.3.2.2.1.22
The number of Airside frames received over the Radio interface in this 15 minutes. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistTxFrms		1.3.6.1.4.1.39003.5.3.3.2.2.1.23
The number of Airside frames transmitted over the Radio interface in this 15 minutes. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistRxPkts		1.3.6.1.4.1.39003.5.3.3.2.2.1.24
The number of Ethernet packets received over the Radio interface in this 15 minutes. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistTxPkts		1.3.6.1.4.1.39003.5.3.3.2.2.1.25
The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this 15 minutes. This does not include packets originating from the management sub-system.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistRxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.2.2.1.26
The number of Ethernet packets received over the Radio interface in this 15 minutes and which are destined for the management sub-system on this unit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistTxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.2.2.1.27
The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this 15 minutes. This does not include packets originating from the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistRxBadFrms		1.3.6.1.4.1.39003.5.3.3.2.2.1.28
The count of bad frames detected on the receive side of the Radio interface in this 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats15mHistQPSKTo8PSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.29
The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHist8PSKToQPSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.30
The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHistAFERMin		1.3.6.1.4.1.39003.5.3.3.2.2.1.31
The minimum AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistAFERMax		1.3.6.1.4.1.39003.5.3.3.2.2.1.32
The maximum AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistAFERAvg		1.3.6.1.4.1.39003.5.3.3.2.2.1.33
The average AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats15mHistRxQPSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.34
The time in seconds that the Rx Modulation Mode was QPSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHistRx8PSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.35
The time in seconds that the Rx Modulation Mode was 8PSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHistTxQPSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.36
The time in seconds that the Tx Modulation Mode was QPSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats15mHistTx8PSK		1.3.6.1.4.1.39003.5.3.3.2.2.1.37
The time in seconds that the Tx Modulation Mode was 8PSK in this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1dHistIntvls		1.3.6.1.4.1.39003.5.3.3.3.1
The number of valid table entries in sub10RadioStats1dHistTable on this system. There is one entry per 1 day interval. If the unit has been running for a minimum of 30 days and collecting valid data then the number of entries will be 30, this represents a total maximum of 30 days worth of data.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..30

sub10RadioStats1dHistTable		1.3.6.1.4.1.39003.5.3.3.3.2
This table maintains a history of Radio statistics based on 1 day intervals. There are a maximum of 30 intervals which represent 30 days of data. This table along with the 1m and 15m tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 day interval where each interval is synchronised to the clock on the hour. There are up to 30 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats1dHistIntvls of which the minimum is 0 and the maximum is 30 therefore providing up to a maximum of 30 days of 1 day interval data. The first entry indexed by 1 represents the most recent completed 1 day interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 30 then the least recent interval entry is discarded.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Sub10RadioStats1dHistEntry

sub10RadioStats1dHistEntry		1.3.6.1.4.1.39003.5.3.3.3.2.1
An entry in the sub10RadioStats1dHistTable. Each entry represents 1 day of performance management data where the first entry with index=1 is the most recent 1 day interval and the last entry with index=n (up to 30) is the least recent 1 day interval. The number of valid intervals is given by the value of sub10RadioStats1dHistIntvls.
Status: current	Access: not-accessible
OBJECT-TYPE
	Sub10RadioStats1dHistEntry

sub10RadioStats1dHistIntvl		1.3.6.1.4.1.39003.5.3.3.3.2.1.1
The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 day interval) and have a maximum value of 24 (the least recent 1 day interval).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..30

sub10RadioStats1dHistTime		1.3.6.1.4.1.39003.5.3.3.3.2.1.2
The local system time when this 1d history entry was created. This represents the end of the 1 day interval for which the associated stats with the same sub10RadioStats1dHistIntvl table index are relevant.
Status: current	Access: read-only
OBJECT-TYPE
	Sub10DateTime

sub10RadioStats1dHistTxPowerMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.3
The minimum value that the transmit power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistTxPowerMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.4
The maximum value that the transmit power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistTxPowerAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.5
The average value that the transmit power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistRxPowerMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.6
The minimum value that the receive power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistRxPowerMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.7
The maximum value that the receive power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistRxPowerAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.8
The average value that the receive power of the local radio link has reached in this day interval, measured in dBm.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistVectErrMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.9
The minimum value that the vector error of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistVectErrMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.10
The maximum value that the vector error of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistVectErrAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.11
The average value that the vector error of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistLnkLossMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.12
The minimum value that the link loss of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistLnkLossMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.13
The maximum value that the link loss of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistLnkLossAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.14
The average value that the link loss of the local radio link has reached in this day interval, measured in dB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistMWUTempMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.15
The minimum MWU temperature measured in this day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistMWUTempMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.16
The maximum MWU temperature measured in this day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistMWUTempAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.17
The average MWU temperature measured in this day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-100..100

sub10RadioStats1dHistRxFrms		1.3.6.1.4.1.39003.5.3.3.3.2.1.22
The number of Airside frames received over the Radio interface in this day interval. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistTxFrms		1.3.6.1.4.1.39003.5.3.3.3.2.1.23
The number of Airside frames transmitted over the Radio interface in this day interval. This is irrespective of whether the Airside frame transmitted contained any ethernet data.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistRxPkts		1.3.6.1.4.1.39003.5.3.3.3.2.1.24
The number of Ethernet packets received over the Radio interface in this day interval. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistTxPkts		1.3.6.1.4.1.39003.5.3.3.3.2.1.25
The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this day interval. This does not include packets originating from the management sub-system.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistRxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.3.2.1.26
The number of Ethernet packets received over the Radio interface in this day interval and which are destined for the management sub-system on this unit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistTxMgmtPkts		1.3.6.1.4.1.39003.5.3.3.3.2.1.27
The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this day interval. This does not include packets originating from the Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistRxBadFrms		1.3.6.1.4.1.39003.5.3.3.3.2.1.28
The count of bad frames detected on the receive side of the Radio interface in this day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistQPSKTo8PSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.29
The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHist8PSKToQPSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.30
The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

sub10RadioStats1dHistAFERMin		1.3.6.1.4.1.39003.5.3.3.3.2.1.31
The minimum AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistAFERMax		1.3.6.1.4.1.39003.5.3.3.3.2.1.32
The maximum AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistAFERAvg		1.3.6.1.4.1.39003.5.3.3.3.2.1.33
The average AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sub10RadioStats1dHistRxQPSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.34
The time in seconds that the Rx Modulation Mode was QPSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1dHistRx8PSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.35
The time in seconds that the Rx Modulation Mode was 8PSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1dHistTxQPSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.36
The time in seconds that the Tx Modulation Mode was QPSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10RadioStats1dHistTx8PSK		1.3.6.1.4.1.39003.5.3.3.3.2.1.37
The time in seconds that the Tx Modulation Mode was 8PSK in this 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sub10Compliance		1.3.6.1.4.1.39003.20.1.1
The compliance statement for Sub10 entities which implement the SUB10SYSTEMS-MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

sub10NotificationsGrp		1.3.6.1.4.1.39003.20.2.1
This group defines objects that are members of the sub10NotificationsGrp group
Status: current	Access: read-only
NOTIFICATION-GROUP

sub10UnitLocalStatusGrp		1.3.6.1.4.1.39003.20.2.2
This group defines objects that are members of the sub10UnitLocalStatusGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitLclAlarmStateEntryGrp		1.3.6.1.4.1.39003.20.2.3
This group defines objects that are members of the sub10UnitLclAlarmStateEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitRemoteStatusGrp		1.3.6.1.4.1.39003.20.2.4
This group defines objects that are members of the sub10UnitRemoteStatusGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSystemGrp		1.3.6.1.4.1.39003.20.2.5
This group defines objects that are members of the sub10UnitMgmtSystemGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtIpGrp		1.3.6.1.4.1.39003.20.2.6
This group defines objects that are members of the sub10UnitMgmtIpGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtVlanGrp		1.3.6.1.4.1.39003.20.2.7
This group defines objects that are members of the sub10UnitMgmtVlanGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtUsersGrp		1.3.6.1.4.1.39003.20.2.8
This group defines objects that are members of the sub10UnitMgmtUsersGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtUserEntryGrp		1.3.6.1.4.1.39003.20.2.9
This group defines objects that are members of the sub10UnitMgmtUserEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtTimeGrp		1.3.6.1.4.1.39003.20.2.10
This group defines objects that are members of the sub10UnitMgmtTimeGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtAlarmEntryGrp		1.3.6.1.4.1.39003.20.2.11
This group defines objects that are members of the sub10UnitMgmtAlarmEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtAlarmsGrp		1.3.6.1.4.1.39003.20.2.12
This group defines objects that are members of the sub10UnitMgmtAlarmsGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSnmpGrp		1.3.6.1.4.1.39003.20.2.13
This group defines objects that are members of the sub10UnitMgmtSnmpGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSnmpTrpDstEntryGrp		1.3.6.1.4.1.39003.20.2.14
This group defines objects that are members of the sub10UnitMgmtSnmpTrpDstEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSnmpUserEntryGrp		1.3.6.1.4.1.39003.20.2.15
This group defines objects that are members of the sub10UnitMgmtSnmpUserEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSnmpAccessEntryGrp		1.3.6.1.4.1.39003.20.2.16
This group defines objects that are members of the sub10UnitMgmtSnmpAccessEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSnmpTargetEntryGrp		1.3.6.1.4.1.39003.20.2.17
This group defines objects that are members of the sub10UnitMgmtSnmpTargetEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtFirmwareGrp		1.3.6.1.4.1.39003.20.2.18
This group defines objects that are members of the sub10UnitMgmtFirmwareGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtFirmwareBankEntryGrp		1.3.6.1.4.1.39003.20.2.19
This group defines objects that are members of the sub10UnitMgmtFirmwareBankEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtDNSEntryGrp		1.3.6.1.4.1.39003.20.2.20
This group defines objects that are members of the sub10UnitMgmtDNSEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtEncryptionGrp		1.3.6.1.4.1.39003.20.2.21
This group defines objects that are members of the sub10UnitMgmtEncryptionGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtLicenseGrp		1.3.6.1.4.1.39003.20.2.22
This group defines objects that are members of the sub10UnitMgmtLicenseGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtSyncEGrp		1.3.6.1.4.1.39003.20.2.23
This group defines objects that are members of the sub10UnitMgmtSyncEGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10UnitMgmtActionsGrp		1.3.6.1.4.1.39003.20.2.24
This group defines objects that are members of the sub10UnitMgmtActionsGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthLclStatusEntryGrp		1.3.6.1.4.1.39003.20.2.25
This group defines objects that are members of the sub10EthLclStatusEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthRmtStatusEntryGrp		1.3.6.1.4.1.39003.20.2.26
This group defines objects that are members of the sub10EthRmtStatusEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtPhyEntryGrp		1.3.6.1.4.1.39003.20.2.27
This group defines objects that are members of the sub10EthMgmtPhyEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtVlanGrp		1.3.6.1.4.1.39003.20.2.28
This group defines objects that are members of the sub10EthMgmtVlanGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtVlanAllowedEntryGrp		1.3.6.1.4.1.39003.20.2.29
This group defines objects that are members of the sub10EthMgmtVlanAllowedEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSGrp		1.3.6.1.4.1.39003.20.2.30
This group defines objects that are members of the sub10EthMgmtQoSGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSQEntryGrp		1.3.6.1.4.1.39003.20.2.31
This group defines objects that are members of the sub10EthMgmtQoSQEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSVlanEntryGrp		1.3.6.1.4.1.39003.20.2.32
This group defines objects that are members of the sub10EthMgmtQoSVlanEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSPCPEntryGrp		1.3.6.1.4.1.39003.20.2.33
This group defines objects that are members of the sub10EthMgmtQoSPCPEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSDSCPEntryGrp		1.3.6.1.4.1.39003.20.2.34
This group defines objects that are members of the sub10EthMgmtQoSDSCPEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtQoSMPLSEntryGrp		1.3.6.1.4.1.39003.20.2.35
This group defines objects that are members of the sub10EthMgmtQoSMPLSEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthMgmtStatsActiveEntryGrp		1.3.6.1.4.1.39003.20.2.36
This group defines objects that are members of the sub10EthMgmtStatsActiveEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthernetStatsGrp		1.3.6.1.4.1.39003.20.2.37
This group defines objects that are members of the sub10EthernetStatsGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthernetStatsCurrEntryGrp		1.3.6.1.4.1.39003.20.2.38
This group defines objects that are members of the sub10EthernetStatsCurrEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthernetStats15mHistoryGrp		1.3.6.1.4.1.39003.20.2.39
This group defines objects that are members of the sub10EthernetStats15mHistoryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthStats15mHistEntryGrp		1.3.6.1.4.1.39003.20.2.40
This group defines objects that are members of the sub10EthStats15mHistEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthStats1dHistoryGrp		1.3.6.1.4.1.39003.20.2.41
This group defines objects that are members of the sub10EthStats1dHistoryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10EthStats1dHistEntryGrp		1.3.6.1.4.1.39003.20.2.42
This group defines objects that are members of the sub10EthStats1dHistEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioLocalStatusGrp		1.3.6.1.4.1.39003.20.2.43
This group defines objects that are members of the sub10RadioLocalStatusGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioRemoteStatusGrp		1.3.6.1.4.1.39003.20.2.44
This group defines objects that are members of the sub10RadioRemoteStatusGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioMgmtGrp		1.3.6.1.4.1.39003.20.2.45
This group defines objects that are members of the sub10RadioMgmtGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioMgmtStatsGrp		1.3.6.1.4.1.39003.20.2.46
This group defines objects that are members of the sub10RadioMgmtStatsGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioMgmtStatsActiveEntryGrp		1.3.6.1.4.1.39003.20.2.47
This group defines objects that are members of the sub10RadioMgmtStatsActiveEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStatsGrp		1.3.6.1.4.1.39003.20.2.48
This group defines objects that are members of the sub10RadioStatsGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStatsCurrentGrp		1.3.6.1.4.1.39003.20.2.49
This group defines objects that are members of the sub10RadioStatsCurrentGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats1mHistoryGrp		1.3.6.1.4.1.39003.20.2.50
This group defines objects that are members of the sub10RadioStats1mHistoryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats1mHistEntryGrp		1.3.6.1.4.1.39003.20.2.51
This group defines objects that are members of the sub10RadioStats1mHistEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats15mHistoryGrp		1.3.6.1.4.1.39003.20.2.52
This group defines objects that are members of the sub10RadioStats15mHistoryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats15mHistEntryGrp		1.3.6.1.4.1.39003.20.2.53
This group defines objects that are members of the sub10RadioStats15mHistEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats1dHistoryGrp		1.3.6.1.4.1.39003.20.2.54
This group defines objects that are members of the sub10RadioStats1dHistoryGrp group
Status: current	Access: read-only
OBJECT-GROUP

sub10RadioStats1dHistEntryGrp		1.3.6.1.4.1.39003.20.2.55
This group defines objects that are members of the sub10RadioStats1dHistEntryGrp group
Status: current	Access: read-only
OBJECT-GROUP