SUN-PLATFORM-MIB

File: SUN-PLATFORM-MIB.mib (112588 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB ENTITY-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY Integer32 Unsigned32
enterprises TEXTUAL-CONVENTION RowStatus
TestAndIncr RowPointer VariablePointer
TruthValue TDomain TAddress
DateAndTime MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP SnmpAdminString entPhysicalEntry
entLogicalEntry entLogicalIndex entPhysicalIndex

Defined Types

SunPlatLogAdministrativeState  
An enumerated value which describes the Administrative State of the log as defined in X.735, sec. 8.1.1.1.3.
TEXTUAL-CONVENTION    
  INTEGER locked(1), unlocked(2)  

SunPlatAdministrativeState  
An enumerated value which describes the Administrative State of the managed object as defined in X.731, sec. 8.1.1.3.
TEXTUAL-CONVENTION    
  INTEGER locked(1), unlocked(2), shuttingDown(3)  

SunPlatOperationalState  
An enumerated value which describes the Operational State of the managed object as defined in X.731, sec. 8.1.1.1.
TEXTUAL-CONVENTION    
  INTEGER disabled(1), enabled(2)  

SunPlatAlarmPerceivedSeverity  
The value of this object identifies the Perceived Severity of an alarm in the log, including 'cleared' as defined in X.733, sec. 8.1.2.3.
TEXTUAL-CONVENTION    
  INTEGER indeterminate(1), critical(2), major(3), minor(4), warning(5), cleared(6)  

SunPlatAlarmStatus  
The value of this object identifies the Alarm Status of the managed object as defined in M.3100, sec. 5.8.
TEXTUAL-CONVENTION    
  INTEGER critical(1), major(2), minor(3), indeterminate(4), warning(5), pending(6), cleared(7)  

SunPlatEquipmentHolderType  
The Equipment Holder Type as defined in M.3100, sec. 5.26.
TEXTUAL-CONVENTION    
  INTEGER bay(1), shelf(2), drawer(3), slot(4), rack(5)  

SunPlatEquipmentHolderStatus  
This attribute identifies whether or not a Circuit Pack is present in the slot and if so, is it recognised/acceptable as defined as Holder Status in M.3100, sec. 5.32.
TEXTUAL-CONVENTION    
  INTEGER holderEmpty(1), inTheAcceptableList(2), notInTheAcceptableList(3), unknownType(4)  

SunPlatEquipmentHolderPower  
An enumeration of possible power management states.
TEXTUAL-CONVENTION    
  INTEGER other(1), unknown(2), powerOff(3), powerOn(4)  

SunPlatCircuitPackAvailabilityStatus  
An enumeration of possible AvailabilityStatus flags as defined in X.731, sec. 8.1.2.3.
TEXTUAL-CONVENTION    
  BITS inTest(0), failed(1), powerOff(2), offLine(3), offDuty(4), dependency(5), degraded(6), notInstalled(7)  

SunPlatProbableCause  
A Probable Cause which provides additional information associated with and alarm notification as per ITU-T M.3100 sec. 10.2, X.733, sec. 8.1.2.1., and X.736.
TEXTUAL-CONVENTION    
  INTEGER aIS(1), callSetUpFailure(2), degradedSignal(3), farEndReceiverFailure(4), framingError(5), lossOfFrame(6), lossOfPointer(7), lossOfSignal(8), payloadTypeMismatch(9), transmissionError(10), remoteAlarmInterface(11), excessiveBER(12), pathTraceMismatch(13), unavailable(14), signalLabelMismatch(15), lossOfMultiFrame(16), receiveFailure(17), transmitFailure(18), modulationFailure(19), demodulationFailure(20), broadcastChannelFailure(21), connectionEstablishmentError(22), invalidMessageReceived(23), localNodeTransmissionError(24), remoteNodeTransmissionError(25), routingFailure(26), backplaneFailure(51), dataSetProblem(52), equipmentIdentifierDuplication(53), externalIFDeviceProblem(54), lineCardProblem(55), multiplexerProblem(56), nEIdentifierDuplication(57), powerProblem(58), processorProblem(59), protectionPathFailure(60), receiverFailure(61), replaceableUnitMissing(62), replaceableUnitTypeMismatch(63), synchronizationSourceMismatch(64), terminalProblem(65), timingProblem(66), transmitterFailure(67), trunkCardProblem(68), replaceableUnitProblem(69), realTimeClockFailure(70), antennaFailure(71), batteryChargingFailure(72), diskFailure(73), frequencyHoppingFailure(74), iODeviceError(75), lossOfSynchronisation(76), lossOfRedundancy(77), powerSupplyFailure(78), signalQualityEvaluationFailure(79), tranceiverFailure(80), protectionMechanismFailure(81), protectingResourceFailure(82), airCompressorFailure(101), airConditioningFailure(102), airDryerFailure(103), batteryDischarging(104), batteryFailure(105), commercialPowerFailure(106), coolingFanFailure(107), engineFailure(108), fireDetectorFailure(109), fuseFailure(110), generatorFailure(111), lowBatteryThreshold(112), pumpFailure(113), rectifierFailure(114), rectifierHighVoltage(115), rectifierLowFVoltage(116), ventilationsSystemFailure(117), enclosureDoorOpen(118), explosiveGas(119), fire(120), flood(121), highHumidity(122), highTemperature(123), highWind(124), iceBuildUp(125), intrusionDetection(126), lowFuel(127), lowHumidity(128), lowCablePressure(129), lowTemperature(130), lowWater(131), smoke(132), toxicGas(133), coolingSystemFailure(134), externalEquipmentFailure(135), externalPointFailure(136), storageCapacityProblem(151), memoryMismatch(152), corruptData(153), outOfCPUCycles(154), sfwrEnvironmentProblem(155), sfwrDownloadFailure(156), lossOfRealTime(157), reinitialized(158), applicationSubsystemFailure(159), configurationOrCustomisationError(160), databaseInconsistency(161), fileError(162), outOfMemory(163), softwareError(164), timeoutExpired(165), underlayingResourceUnavailable(166), versionMismatch(167), bandwidthReduced(201), congestion(202), excessiveErrorRate(203), excessiveResponseTime(204), excessiveRetransmissionRate(205), reducedLoggingCapability(206), systemResourcesOverload(207), other(255), adapterError(256), callEstablishmentError(257), communicationsProtocolError(258), communicationsSubsystemFailure(259), configurationOrCustomizationError(260), cpuCyclesLimitExceeded(261), dataSetOrModemError(262), dteDceInterfaceError(263), equipmentMalfunction(264), excessiveVibration(265), fireDetected(266), floodDetected(267), heatingVentCoolingSystemProblem(268), humidityUnacceptable(269), inputOutputDeviceError(270), inputDeviceError(271), lanError(272), leakDetected(273), materialSupplyExhausted(274), ouputDeviceError(275), performanceDegraded(276), pressureUnacceptable(277), queueSizeExceeded(278), resourceAtOrNearingCapacity(279), responseTimeExecessive(280), retransmissionRateExcessive(281), softwareProgramAbnormallyTerminated(282), softwareProgramError(283), temperatureUnacceptable(284), thresholdCrossed(285), toxicLeakDetected(286), underlyingResourceUnavailable(287), authenticationFailure(288), breachOfConfidentiality(289), cableTamper(290), delayedInformation(291), denialOfService(292), duplicateInformation(293), informationMissing(294), informationModificationDetected(295), informationOutOfSequence(296), keyExpired(297), nonRepudiationFailure(298), outOfHoursActivity(299), outOfService(300), proceduralError(301), unauthorizedAccessAttempt(302), unexpectedInformation(303)  

SunPlatPhysicalClass  
An enumeration of possible physical classes where entPhysicalClass is specified as other(1).
TEXTUAL-CONVENTION    
  INTEGER other(1), alarm(2), watchdog(3)  

SunPlatSensorClass  
An enumeration of possible sensor classes where entPhysicalClass is specified as sensor(8).
TEXTUAL-CONVENTION    
  INTEGER binary(1), numeric(2), discrete(3)  

SunPlatSensorType  
An enumeration of possible sensor types where entPhysicalClass is specified as sensor(8).
TEXTUAL-CONVENTION    
  INTEGER other(1), unknown(2), temperature(3), voltage(4), current(5), tachometer(6), counter(7), switch(8), lock(9), humidity(10), smokeDetection(11), presence(12), airFlow(13)  

SunPlatBaseUnits  
Physical values are represented in the units obtained by (sunPlatBaseUnits * 10 raised to the power of sunPlatExponent). For example, if sunPlatBaseUnits is volts(6) and sunPlatExponent is -6, then the units of the values returned are microVolts.
TEXTUAL-CONVENTION    
  INTEGER other(1), unknown(2), degC(3), degF(4), degK(5), volts(6), amps(7), watts(8), joules(9), coulombs(10), va(11), nits(12), lumens(13), lux(14), candelas(15), kPa(16), psi(17), newtons(18), cfm(19), rpm(20), hertz(21), seconds(22), minutes(23), hours(24), days(25), weeks(26), mils(27), inches(28), feet(29), cubicInches(30), cubicFeet(31), meters(32), cubicCentimeters(33), cubicMeters(34), liters(35), fluidOunces(36), radians(37), steradians(38), revolutions(39), cycles(40), gravities(41), ounces(42), pounds(43), footPounds(44), ounceInches(45), gauss(46), gilberts(47), henries(48), farads(49), ohms(50), siemens(51), moles(52), becquerels(53), ppm(54), decibels(55), dBA(56), dbC(57), grays(58), sieverts(59), colorTemperatureDegK(60), bits(61), bytes(62), words(63), doubleWords(64), quadWords(65), percentage(66)  

SunPlatRateUnits  
If sunPlatRateUnits is set to a value other than none(1), then the units specified by sunPlatBaseUnits are further qualified as rate units. For example, if sunPlatBaseUnits is set to degC(3), and sunPlatRateUnits is set to perSecond(4), then the value represented has the units degC/Second.
TEXTUAL-CONVENTION    
  INTEGER none(1), perMicroSecond(2), perMilliSecond(3), perSecond(4), perMinute(5), perHour(6), perDay(7), perWeek(8), perMonth(9), perYear(10)  

SunPlatNumericSensorEnabledThresholds  
The possible thresholds that may be enabled by a sensor.
TEXTUAL-CONVENTION    
  BITS lowerThresholdNonCritical(0), upperThresholdNonCritical(1), lowerThresholdCritical(2), upperThresholdCritical(3), lowerThresholdFatal(4), upperThresholdFatal(5)  

SunPlatNumericSensorThresholdResetAction  
The possible reset actions that may be performed on a sensor.
TEXTUAL-CONVENTION    
  INTEGER reset(1)  

SunPlatAlarmType  
This indicates the type of alarm - i.e. the means by which the alarm condition is communicated.
TEXTUAL-CONVENTION    
  INTEGER other(1), audible(2), visible(3), motion(4), switch(5)  

SunPlatAlarmState  
This indicates the state of the alarm.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), off(2), steady(3), alternating(4)  

SunPlatAlarmUrgency  
An enumeration of possible alarm urgencies, as defined for CIM_AlarmDevice.Urgency.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), other(2), notSupported(3), informational(4), nonCritical(5), critical(6), unrecoverable(7)  

SunPlatWatchdogAction  
This indicates the action taken by the watchdog if it is not reset within the period specified by sunPlatWatchdogTimeout.
TEXTUAL-CONVENTION    
  INTEGER statusOnly(1), systemInterrupt(2), systemReset(3), systemPowerOff(4), systemPowerCycle(5)  

SunPlatWatchdogMonitoredEntity  
An enumeration of possible entities that may be monitored by a watchdog as defined for CIM_Watchdog
TEXTUAL-CONVENTION    
  INTEGER unknown(1), other(2), operatingSystem(3), operatingSystemBootProcess(4), operatingSystemShutdownProcess(5), firmwareBootProcess(6), biosBootProcess(7), application(8), serviceProcessor(9)  

SunPlatPowerSupplyClass  
An enumeration of possible classes of power supply.
TEXTUAL-CONVENTION    
  INTEGER other(1), powerSupply(2), battery(3)  

SunPlatFanClass  
An enumeration of possible classes of cooling device that may be represented with an entPhysicalClass of fan(7)
TEXTUAL-CONVENTION    
  INTEGER other(1), fan(2), refrigeration(3), heatPipe(4)  

SunPlatBatteryStatus  
An enumeration of possible battery statuses as defined for CIM_Battery.BatteryStatus.
TEXTUAL-CONVENTION    
  INTEGER other(1), unknown(2), fullyCharged(3), low(4), critical(5), charging(6), chargingAndHigh(7), chargingAndLow(8), chargingAndCritical(9), undefined(10), partiallyCharged(11)  

SunPlatUnitaryComputerSystemPowerState  
An enumeration of possible power states defined for CIM_UnitaryComputerSystem.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), fullPower(2), psLowPower(3), psStandby(4), psOther(5), powerCycle(6), powerOff(7), psWarning(8), hibernate(9), softOff(10), reset(11)  

SunPlatUnitaryComputerSystemApplicableSetting  
This specifies a setting which may be applied to an instance of CIM_UnitaryComputerSystem.
TEXTUAL-CONVENTION    
  INTEGER defaultSetting(1), specifiedSetting(2)  

SunPlatLogicalClass  
An enumeration of the possible logical classes.
TEXTUAL-CONVENTION    
  INTEGER other(1), computerSystem(2), adminDomain(3)  

SunPlatLogicalStatus  
An enumeration of possible status values.
TEXTUAL-CONVENTION    
  INTEGER ok(1), error(2), degraded(3), unknown(4), predFail(5), starting(6), stopping(7), service(8), stressed(9), nonRecover(10), noContact(11), lostComm(12), stopped(13)  

SunPlatIndex  
An arbitrary value which uniquely identifies the row.
TEXTUAL-CONVENTION    
  INTEGER 1..2147483647  

SunPlatPercentage  
Used to express a value, in 100ths of a %.
TEXTUAL-CONVENTION    
  INTEGER 0..2147483647  

SunPlatEquipmentEntry  
SEQUENCE    
  sunPlatEquipmentAdministrativeState SunPlatAdministrativeState
  sunPlatEquipmentOperationalState SunPlatOperationalState
  sunPlatEquipmentAlarmStatus SunPlatAlarmStatus
  sunPlatEquipmentUnknownStatus TruthValue
  sunPlatEquipmentLocationName SnmpAdminString

SunPlatEquipmentHolderEntry  
SEQUENCE    
  sunPlatEquipmentHolderType SunPlatEquipmentHolderType
  sunPlatEquipmentHolderAcceptableTypes SnmpAdminString
  sunPlatEquipmentHolderStatus SunPlatEquipmentHolderStatus
  sunPlatEquipmentHolderPowered SunPlatEquipmentHolderPower

SunPlatCircuitPackEntry  
SEQUENCE    
  sunPlatCircuitPackType SnmpAdminString
  sunPlatCircuitPackAvailabilityStatus SunPlatCircuitPackAvailabilityStatus
  sunPlatCircuitPackReplaceable TruthValue
  sunPlatCircuitPackHotSwappable TruthValue

SunPlatPhysicalEntry  
SEQUENCE    
  sunPlatPhysicalClass SunPlatPhysicalClass

SunPlatSensorEntry  
SEQUENCE    
  sunPlatSensorClass SunPlatSensorClass
  sunPlatSensorType SunPlatSensorType
  sunPlatSensorLatency Unsigned32

SunPlatBinarySensorEntry  
SEQUENCE    
  sunPlatBinarySensorCurrent TruthValue
  sunPlatBinarySensorExpected TruthValue
  sunPlatBinarySensorInterpretTrue SnmpAdminString
  sunPlatBinarySensorInterpretFalse SnmpAdminString

SunPlatNumericSensorEntry  
SEQUENCE    
  sunPlatNumericSensorBaseUnits SunPlatBaseUnits
  sunPlatNumericSensorExponent Integer32
  sunPlatNumericSensorRateUnits SunPlatRateUnits
  sunPlatNumericSensorCurrent Integer32
  sunPlatNumericSensorNormalMin Integer32
  sunPlatNumericSensorNormalMax Integer32
  sunPlatNumericSensorAccuracy SunPlatPercentage
  sunPlatNumericSensorLowerThresholdNonCritical Integer32
  sunPlatNumericSensorUpperThresholdNonCritical Integer32
  sunPlatNumericSensorLowerThresholdCritical Integer32
  sunPlatNumericSensorUpperThresholdCritical Integer32
  sunPlatNumericSensorLowerThresholdFatal Integer32
  sunPlatNumericSensorUpperThresholdFatal Integer32
  sunPlatNumericSensorHysteresis Unsigned32
  sunPlatNumericSensorEnabledThresholds SunPlatNumericSensorEnabledThresholds
  sunPlatNumericSensorRestoreDefaultThresholds SunPlatNumericSensorThresholdResetAction

SunPlatDiscreteSensorEntry  
SEQUENCE    
  sunPlatDiscreteSensorCurrent SunPlatIndex

SunPlatDiscreteSensorStatesEntry  
SEQUENCE    
  sunPlatDiscreteSensorStatesIndex SunPlatIndex
  sunPlatDiscreteSensorStatesInterpretation SnmpAdminString
  sunPlatDiscreteSensorStatesAcceptable TruthValue

SunPlatFanEntry  
SEQUENCE    
  sunPlatFanClass SunPlatFanClass

SunPlatAlarmEntry  
SEQUENCE    
  sunPlatAlarmType SunPlatAlarmType
  sunPlatAlarmState SunPlatAlarmState
  sunPlatAlarmUrgency SunPlatAlarmUrgency

SunPlatWatchdogEntry  
SEQUENCE    
  sunPlatWatchdogTimeout Unsigned32
  sunPlatWatchdogAction SunPlatWatchdogAction
  sunPlatWatchdogLastExpired DateAndTime
  sunPlatWatchdogMonitoredEntity SunPlatWatchdogMonitoredEntity

SunPlatPowerSupplyEntry  
SEQUENCE    
  sunPlatPowerSupplyClass SunPlatPowerSupplyClass

SunPlatBatteryEntry  
SEQUENCE    
  sunPlatBatteryStatus SunPlatBatteryStatus

SunPlatLogicalEntry  
SEQUENCE    
  sunPlatLogicalClass SunPlatLogicalClass
  sunPlatLogicalStatus SunPlatLogicalStatus

SunPlatUnitaryComputerSystemEntry  
SEQUENCE    
  sunPlatUnitaryComputerSystemPowerState SunPlatUnitaryComputerSystemPowerState
  sunPlatUnitaryComputerSystemApplySettings SunPlatUnitaryComputerSystemApplicableSetting

SunPlatInitialLoadInfoEntry  
SEQUENCE    
  sunPlatInitialLoadInfoIndex SunPlatIndex
  sunPlatInitialLoadInfoDescr SnmpAdminString
  sunPlatInitialLoadInfoCurrentValue SnmpAdminString
  sunPlatInitialLoadInfoDesiredValue SnmpAdminString

SunPlatLogEntry  
SEQUENCE    
  sunPlatLogType OBJECT IDENTIFIER
  sunPlatLogAdministrativeState SunPlatLogAdministrativeState
  sunPlatLogOperationalState SunPlatOperationalState
  sunPlatLogFullStatus TruthValue
  sunPlatLogCapacityThreshold SunPlatPercentage
  sunPlatLogRowStatus RowStatus

SunPlatLogRecordEntry  
SEQUENCE    
  sunPlatLogRecordId Unsigned32
  sunPlatLogRecordLoggingTime DateAndTime
  sunPlatLogRecordManagedObjectInstance RowPointer
  sunPlatLogRecordRowStatus RowStatus
  sunPlatLogRecordCorrelatedNotifications SnmpAdminString

SunPlatLogRecordAdditionalEntry  
SEQUENCE    
  sunPlatLogRecordAdditionalInfo OBJECT IDENTIFIER
  sunPlatLogRecordAdditionalText SnmpAdminString

SunPlatLogRecordAlarmEntry  
SEQUENCE    
  sunPlatLogRecordAlarmPerceivedSeverity SunPlatAlarmPerceivedSeverity
  sunPlatLogRecordAlarmProbableCause SunPlatProbableCause
  sunPlatLogRecordAlarmSpecificProblem SnmpAdminString
  sunPlatLogRecordAlarmRepairAction SnmpAdminString

SunPlatLogRecordChangeEntry  
SEQUENCE    
  sunPlatLogRecordChangeChangedOID VariablePointer
  sunPlatLogRecordChangeNewInteger INTEGER
  sunPlatLogRecordChangeOldInteger INTEGER
  sunPlatLogRecordChangeNewString OCTET STRING
  sunPlatLogRecordChangeOldString OCTET STRING
  sunPlatLogRecordChangeNewOID OBJECT IDENTIFIER
  sunPlatLogRecordChangeOldOID OBJECT IDENTIFIER

Defined Values

sun 1.3.6.1.4.1.42
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.42.2
OBJECT IDENTIFIER    

sunFire 1.3.6.1.4.1.42.2.70
OBJECT IDENTIFIER    

sunPlatMIB 1.3.6.1.4.1.42.2.70.101
SUN-PLATFORM-MIB.mib Version 1.19 Copyright 2003, by Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. The SUN-PLATFORM-MIB provides extensions to the ENTITY-MIB (RFC2737) where each entity modelled in the system is represented by means of extensions to the entPhysicalTable. Certain of the attributes in the entPhysicalTable are applicable to the model presented by the SUN-PLATFORM-MIB and are explained below: The entries in the entPhysicalTable have the following significance with respect to the SUN-PLATFORM-MIB model: entPhysicalIndex containment, M.3100, fig. 2, index for table extensions. entPhysicalContainedIn containment, M.3100, fig. 2 entPhysicalClass Used to select applicable table extensions, Managed Object Class, M.3100, Table 1 entPhysicalHardwareRev version, M.3100, sec. 5.71 entPhysicalFirmwareRev version, M.3100, sec. 5.71 entPhysicalSoftwareRev version, M.3100, sec. 5.71 entPhysicalMfgName vendorName, M.3100, sec. 5.70 entPhysicalAlias userLabel, M.3100, sec. 5.69 Part of this MIB module is an SNMP version of the Generic Network Information Model (NIM) presented in ITU-T M.3100. This information is further extended by attributes derived from the CIM v2.5 Schema. The containment hierarchy is modelled using the ENTITY-MIB (RFC2737) where each entity modelled in the system is represented by means of extensions to the entPhysicalTable. Where an entity is an instance of a managed object class which is sub-classed from another, the attributes of each class are modelled in a separate table extension. For example for an entity with an entPhysicalClass of module(9), which corresponds to a Circuit Pack, sub-classed from Equipment, an entry will exist in the sunPlatEquipmentTable, with additional attributes in the sunPlatCircuitPackTable. References are made to the following recommendations/revisions: ITU-T M.3100 (07/95) CCITT X.721 (1992 E) CCITT X.731 (1992 E) (01/92) CCITT X.733 (1992 E) CCITT X.734 (1992 E) CCITT X.735 (1992 E) (09/92) CIM Schema: Version 2.5
MODULE-IDENTITY    

sunPlatMIBObjects 1.3.6.1.4.1.42.2.70.101.1
OBJECT IDENTIFIER    

sunPlatMIBTraps 1.3.6.1.4.1.42.2.70.101.2
OBJECT IDENTIFIER    

sunPlatMIBPhysicalObjects 1.3.6.1.4.1.42.2.70.101.1.1
OBJECT IDENTIFIER    

sunPlatMIBLogicalObjects 1.3.6.1.4.1.42.2.70.101.1.2
OBJECT IDENTIFIER    

sunPlatMIBLogs 1.3.6.1.4.1.42.2.70.101.1.3
OBJECT IDENTIFIER    

sunPlatMIBTrapPrefix 1.3.6.1.4.1.42.2.70.101.2.0
OBJECT IDENTIFIER    

sunPlatMIBTrapData 1.3.6.1.4.1.42.2.70.101.2.1
OBJECT IDENTIFIER    

sunPlatMIBConformances 1.3.6.1.4.1.42.2.70.101.3
OBJECT IDENTIFIER    

sunPlatMIBCompliances 1.3.6.1.4.1.42.2.70.101.3.1
OBJECT IDENTIFIER    

sunPlatMIBGroups 1.3.6.1.4.1.42.2.70.101.3.2
OBJECT IDENTIFIER    

sunPlatMIBObjectGroups 1.3.6.1.4.1.42.2.70.101.3.2.1
OBJECT IDENTIFIER    

sunPlatMIBNotifGroups 1.3.6.1.4.1.42.2.70.101.3.2.2
OBJECT IDENTIFIER    

sunPlatStartTime 1.3.6.1.4.1.42.2.70.101.1.1.1
The time at which the agent was last started; in other words, the time at which sysUpTime was zero.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

sunPlatEquipmentTable 1.3.6.1.4.1.42.2.70.101.1.1.2
The NIM Equipment table. This table augments the entPhysicalTable to provide the attributes defined for equipment under M.3100, sec. 3.2.2. Additional packages may be supported using further table extensions. The sunPlatEquipmentTable is valid for entPhysicalClass values of chassis(3), backplane(4), container(5), powerSupply(6), fan(7), sensor(8), module(9), and other(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatEquipmentEntry

sunPlatEquipmentEntry 1.3.6.1.4.1.42.2.70.101.1.1.2.1
An entry in the NIM Equipment table. Each entry of this table represents a piece of equipment within the network element of the type specified by entPhysicalClass.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatEquipmentEntry  

sunPlatEquipmentAdministrativeState 1.3.6.1.4.1.42.2.70.101.1.1.2.1.1
An enumerated value which describes the Administrative State of the managed object as defined in X.731, sec. 8.1.1.3.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatAdministrativeState  

sunPlatEquipmentOperationalState 1.3.6.1.4.1.42.2.70.101.1.1.2.1.2
An enumerated value which describes the Operational State of the managed object as defined in X.731, sec. 8.1.1.1.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatOperationalState  

sunPlatEquipmentAlarmStatus 1.3.6.1.4.1.42.2.70.101.1.1.2.1.3
The value of this object identifies the Alarm Status of the managed object as defined in M.3100, sec. 5.8.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatAlarmStatus  

sunPlatEquipmentUnknownStatus 1.3.6.1.4.1.42.2.70.101.1.1.2.1.4
This attribute identifies whether or not the state of the entity is known as defined as Unknown Status in X.731, sec. 8.1.2.6.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatEquipmentLocationName 1.3.6.1.4.1.42.2.70.101.1.1.2.1.5
The specific or general location of the component as defined as Location Name in M.3100, sec. 5.37.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

sunPlatEquipmentHolderTable 1.3.6.1.4.1.42.2.70.101.1.1.3
The NIM Equipment-Holder table. This table augments the entPhysicalTable to provide the attributes defined for equipmentHolder under M.3100, sec. 3.2.3. It is valid for an entPhysicalClass of container(5).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatEquipmentHolderEntry

sunPlatEquipmentHolderEntry 1.3.6.1.4.1.42.2.70.101.1.1.3.1
An entry in the NIM Equipment-Holder table. Each entry of this table represents a component within the network element that accepts a replaceable Circuit Pack.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatEquipmentHolderEntry  

sunPlatEquipmentHolderType 1.3.6.1.4.1.42.2.70.101.1.1.3.1.1
The type of the component as defined in M.3100, sec. 5.26.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatEquipmentHolderType  

sunPlatEquipmentHolderAcceptableTypes 1.3.6.1.4.1.42.2.70.101.1.1.3.1.2
The types of Circuit Pack that can be supported by the slot, separated by newline characters as defined in M.3100, sec. 5.2.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatEquipmentHolderStatus 1.3.6.1.4.1.42.2.70.101.1.1.3.1.3
This attributes identifies whether or not a Circuit Pack is present in the slot as defined in M.3100, sec. 5.32.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatEquipmentHolderStatus  

sunPlatEquipmentHolderPowered 1.3.6.1.4.1.42.2.70.101.1.1.3.1.4
The current power management state of the equipment holder.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatEquipmentHolderPower  

sunPlatCircuitPackTable 1.3.6.1.4.1.42.2.70.101.1.1.4
The NIM Circuit-Pack table. This table augments the entPhysicalTable to provide the attributes defined for circuitPack under M.3100, sec. 3.2.1. It is valid for an entPhysicalClass of module(9).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatCircuitPackEntry

sunPlatCircuitPackEntry 1.3.6.1.4.1.42.2.70.101.1.1.4.1
An entry in the NIM Circuit-Pack table. Each entry of this table represents a piece of equipment within the network element that is inserted into and removed from an Equipment-Holder.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatCircuitPackEntry  

sunPlatCircuitPackType 1.3.6.1.4.1.42.2.70.101.1.1.4.1.1
The type of this circuit pack as defined in M.3100, sec. 5.13.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatCircuitPackAvailabilityStatus 1.3.6.1.4.1.42.2.70.101.1.1.4.1.2
The availability status attribute as defined in X.731, sec. 8.1.2.3.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatCircuitPackAvailabilityStatus  

sunPlatCircuitPackReplaceable 1.3.6.1.4.1.42.2.70.101.1.1.4.1.3
The CIM_PhysicalPackage.Replaceable property as defined by the CIM_Physical Schema.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatCircuitPackHotSwappable 1.3.6.1.4.1.42.2.70.101.1.1.4.1.4
The CIM_PhysicalPackage.HotSwappable property as defined by the CIM_Physical Schema.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatPhysicalTable 1.3.6.1.4.1.42.2.70.101.1.1.5
The Sun Platform Physical Class Table extension. This table is used to define the physical class of the entity if it is classified as other(1). The sunPlatPhysicalTable is valid for the entPhysicalClass value of other(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatPhysicalEntry

sunPlatPhysicalEntry 1.3.6.1.4.1.42.2.70.101.1.1.5.1
An entry in the Sun Platform Physical Class Table extension. Each entry of this table represents a piece of equipment with an entPhysicalClass of other(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatPhysicalEntry  

sunPlatPhysicalClass 1.3.6.1.4.1.42.2.70.101.1.1.5.1.1
An enumeration of possible physical classes where entPhysicalClass is specified as other(1).
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatPhysicalClass  

sunPlatSensorTable 1.3.6.1.4.1.42.2.70.101.1.1.6
The Sun Platform Sensor Table extension. This table augments the entPhysicalTable to provide the attributes common to all sensors. The sunPlatSensorTable is valid for the entPhysicalClass value of sensor(8).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatSensorEntry

sunPlatSensorEntry 1.3.6.1.4.1.42.2.70.101.1.1.6.1
An entry in the Sun Platform Sensor Table extension. Each entry of this table represents a piece of equipment with an entPhysicalClass of sensor(8).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatSensorEntry  

sunPlatSensorClass 1.3.6.1.4.1.42.2.70.101.1.1.6.1.1
An enumeration of possible sensor classes where entPhysicalClass is specified as sensor(8).
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatSensorClass  

sunPlatSensorType 1.3.6.1.4.1.42.2.70.101.1.1.6.1.2
An enumeration of possible sensor types where entPhysicalClass is specified as sensor(8).
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatSensorType  

sunPlatSensorLatency 1.3.6.1.4.1.42.2.70.101.1.1.6.1.3
Where the sensor is polled this value represents the update interval for this sensor measured in mS. Where the sensor is event driven rather than polled, this value should represent the maximum expected latency in processing that event.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sunPlatBinarySensorTable 1.3.6.1.4.1.42.2.70.101.1.1.7
The Sun Platform BinarySensor Table extension. This table augments the sunPlatSensorTable to provide the attributes specific to binary sensors. The sunPlatBinarySensorTable is valid for the sunPlatSensorClass value of binary(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatBinarySensorEntry

sunPlatBinarySensorEntry 1.3.6.1.4.1.42.2.70.101.1.1.7.1
An entry in the Sun Platform BinarySensor Table extension. Each entry of this table represents a sensor with a sunPlatSensorClass value of binary(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatBinarySensorEntry  

sunPlatBinarySensorCurrent 1.3.6.1.4.1.42.2.70.101.1.1.7.1.1
The current state of the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatBinarySensorExpected 1.3.6.1.4.1.42.2.70.101.1.1.7.1.2
The expected state of the sensor. If there is no expected value then no value is returned for this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatBinarySensorInterpretTrue 1.3.6.1.4.1.42.2.70.101.1.1.7.1.3
The interpretation to be applied to a sensor reading of true.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatBinarySensorInterpretFalse 1.3.6.1.4.1.42.2.70.101.1.1.7.1.4
The interpretation to be applied to a sensor reading of false.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatNumericSensorTable 1.3.6.1.4.1.42.2.70.101.1.1.8
The Sun Platform NumericSensor Table extension. This table augments the sunPlatSensorTable to provide the attributes specific to numeric sensors. The sunPlatNumericSensorTable is valid for the sunPlatSensorClass value of numeric(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatNumericSensorEntry

sunPlatNumericSensorEntry 1.3.6.1.4.1.42.2.70.101.1.1.8.1
An entry in the Sun Platform NumericSensor Table extension. Each entry of this table represents a sensor with a sunPlatSensorClass value of numeric(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatNumericSensorEntry  

sunPlatNumericSensorBaseUnits 1.3.6.1.4.1.42.2.70.101.1.1.8.1.1
The base unit of the values returned by this Sensor, as per CIM_NumericSensor.BaseUnits. Physical values are represented in the units obtained by (sunPlatBaseUnits * 10 raised to the power of sunPlatExponent). For example, if sunPlatBaseUnits is volts(6) and sunPlatExponent is -6, then the units of the values returned are microVolts.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatBaseUnits  

sunPlatNumericSensorExponent 1.3.6.1.4.1.42.2.70.101.1.1.8.1.2
The exponent to be applied to the units returned by this sensor as for CIM_NumericSensor.UnitModifier.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorRateUnits 1.3.6.1.4.1.42.2.70.101.1.1.8.1.3
If sunPlatRateUnits is set to a value other than none(1), then the units specified by sunPlatBaseUnits are further qualified as rate units. For example, if sunPlatBaseUnits is set to degC(3), and sunPlatRateUnits is set to perSecond(4), then the value represented has the units degC/Second. This is as defined for CIM_NumericSensor.RateUnits
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatRateUnits  

sunPlatNumericSensorCurrent 1.3.6.1.4.1.42.2.70.101.1.1.8.1.4
The current state of the sensor as per CIM_NumericSensor.CurrentReading.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorNormalMin 1.3.6.1.4.1.42.2.70.101.1.1.8.1.5
The lowest expected value from this sensor as defined for CIM_NumericSensor.NormalMin. If there is no minimum value then no value is returned for this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorNormalMax 1.3.6.1.4.1.42.2.70.101.1.1.8.1.6
The highest expected value from this sensor as defined for CIM_NumericSensor.NormalMax. If there is no maximum value then no value is returned for this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorAccuracy 1.3.6.1.4.1.42.2.70.101.1.1.8.1.7
The accuracy as defined for CIM_NumericSensor.Accuracy of this sensor expressed as a +/-% value in units of 100ths of a percent.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatPercentage  

sunPlatNumericSensorLowerThresholdNonCritical 1.3.6.1.4.1.42.2.70.101.1.1.8.1.8
This attribute describes the lower threshold at which a NonCritical condition occurs as defined for CIM_NumericSensor.LowerThresholdNonCritical.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorUpperThresholdNonCritical 1.3.6.1.4.1.42.2.70.101.1.1.8.1.9
This attribute describes the upper threshold at which a NonCritical condition occurs as defined for CIM_NumericSensor.UpperThresholdNonCritical.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorLowerThresholdCritical 1.3.6.1.4.1.42.2.70.101.1.1.8.1.10
This attribute describes the lower threshold at which a Critical condition occurs as defined for CIM_NumericSensor.LowerThresholdCritical.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorUpperThresholdCritical 1.3.6.1.4.1.42.2.70.101.1.1.8.1.11
This attribute describes the upper threshold at which a Critical condition occurs as defined for CIM_NumericSensor.UpperThresholdCritical.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorLowerThresholdFatal 1.3.6.1.4.1.42.2.70.101.1.1.8.1.12
This attribute describes the lower threshold at which a Fatal condition occurs as defined for CIM_NumericSensor.LowerThresholdFatal.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorUpperThresholdFatal 1.3.6.1.4.1.42.2.70.101.1.1.8.1.13
This attribute describes the upper threshold at which a Fatal condition occurs as defined for CIM_NumericSensor.UpperThresholdFatal.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sunPlatNumericSensorHysteresis 1.3.6.1.4.1.42.2.70.101.1.1.8.1.14
This attribute describes the hysteresis around the thresholds as defined by CIM_NumericSensor.Hysteresis.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sunPlatNumericSensorEnabledThresholds 1.3.6.1.4.1.42.2.70.101.1.1.8.1.15
This attribute describes the enabled thresholds of this sensor as defined for CIM_NumericSensor.EnabledThresholds.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatNumericSensorEnabledThresholds  

sunPlatNumericSensorRestoreDefaultThresholds 1.3.6.1.4.1.42.2.70.101.1.1.8.1.16
Writing to this attribute resets the sensors thresholds to the default settings.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatNumericSensorThresholdResetAction  

sunPlatDiscreteSensorTable 1.3.6.1.4.1.42.2.70.101.1.1.9
The Discrete Sensor Table. This table is valid for rows with an entPhysicalClass of sensor(8) and a sunPlatSensorClass of discrete(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatDiscreteSensorEntry

sunPlatDiscreteSensorEntry 1.3.6.1.4.1.42.2.70.101.1.1.9.1
An entry in the Discrete Sensor Table. Each entry in this table represents a discrete sensor with entPhysicalClass of sensor(8) and discrete(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatDiscreteSensorEntry  

sunPlatDiscreteSensorCurrent 1.3.6.1.4.1.42.2.70.101.1.1.9.1.1
The sunPlatDiscreteSensorStatesIndex of a row in the sunPlatDiscreteSensorStatesTable which corresponds to the current reading of the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatIndex  

sunPlatDiscreteSensorStatesTable 1.3.6.1.4.1.42.2.70.101.1.1.10
The Discrete Sensor States Table. This table describes the available states for a discrete sensor in the Discrete Sensor Table. This table is valid for an entPhysicalClass value of sensor(8) with a sunPlatSensorClass of discrete(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatDiscreteSensorStatesEntry

sunPlatDiscreteSensorStatesEntry 1.3.6.1.4.1.42.2.70.101.1.1.10.1
An entry in the Discrete Sensor States Table. Each entry in this table represents a possible sensor state for the corresponding sensor in the Discrete Sensor Table. The current state of the sensor is indicated by the value of sunPlatDiscreteSensorCurrent for the corresponding sunPlatDiscreteSensorTable entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatDiscreteSensorStatesEntry  

sunPlatDiscreteSensorStatesIndex 1.3.6.1.4.1.42.2.70.101.1.1.10.1.1
A number identifying this sensor state.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatIndex  

sunPlatDiscreteSensorStatesInterpretation 1.3.6.1.4.1.42.2.70.101.1.1.10.1.2
This attribute describes the state represented by the corresponding row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatDiscreteSensorStatesAcceptable 1.3.6.1.4.1.42.2.70.101.1.1.10.1.3
This attribute describes whether this value is acceptable as defined for CIM_DiscreteSensor.AcceptableValues.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatFanTable 1.3.6.1.4.1.42.2.70.101.1.1.11
The Sun Platform Fan Table extension. This table augments the entPhysicalTable to provide the attributes common to all fans and cooling devices. The sunPlatFanTable is valid for the entPhysicalClass value of fan(7).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatFanEntry

sunPlatFanEntry 1.3.6.1.4.1.42.2.70.101.1.1.11.1
An entry in the Sun Platform Fan Table extension. Each entry of this table represents a piece of equipment with an entPhysicalClass of fan(7).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatFanEntry  

sunPlatFanClass 1.3.6.1.4.1.42.2.70.101.1.1.11.1.1
This attribute describes the class of the cooling device.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatFanClass  

sunPlatAlarmTable 1.3.6.1.4.1.42.2.70.101.1.1.12
The Sun Platform Alarm Table extension. This table augments the entPhysicalTable to provide indications of alarm states. The sunPlatAlarmTable is valid for the sunPlatPhysicalClass value of alarm(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatAlarmEntry

sunPlatAlarmEntry 1.3.6.1.4.1.42.2.70.101.1.1.12.1
An entry in the Sun Platform Alarm Table extension. Each entry of this table represents a piece of equipment with an sunPlatPhysicalClass of alarm(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatAlarmEntry  

sunPlatAlarmType 1.3.6.1.4.1.42.2.70.101.1.1.12.1.1
This indicates the type of alarm - i.e. the means by which the alarm condition is communicated.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatAlarmType  

sunPlatAlarmState 1.3.6.1.4.1.42.2.70.101.1.1.12.1.2
This indicates the state of the alarm as defined for CIM_AlarmDevice.AlarmState.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatAlarmState  

sunPlatAlarmUrgency 1.3.6.1.4.1.42.2.70.101.1.1.12.1.3
This attribute describes the urgency of the alarm as defined for CIM_AlarmDevice.Urgency.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatAlarmUrgency  

sunPlatWatchdogTable 1.3.6.1.4.1.42.2.70.101.1.1.13
The Sun Platform Watchdog Table extension. This table augments the entPhysicalTable to provide information about a watchdog timer. The sunPlatWatchdogTable is valid for the sunPlatPhysicalClass value of watchdog(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatWatchdogEntry

sunPlatWatchdogEntry 1.3.6.1.4.1.42.2.70.101.1.1.13.1
An entry in the Sun Platform Watchdog Table extension. Each entry of this table represents a piece of equipment with an sunPlatPhysicalClass of watchdog(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatWatchdogEntry  

sunPlatWatchdogTimeout 1.3.6.1.4.1.42.2.70.101.1.1.13.1.1
This indicates the interval in mS after which the watchdog will timeout if not reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sunPlatWatchdogAction 1.3.6.1.4.1.42.2.70.101.1.1.13.1.2
This indicates the action taken by the watchdog if it is not reset within the period specified by sunPlatWatchdogTimeout.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatWatchdogAction  

sunPlatWatchdogLastExpired 1.3.6.1.4.1.42.2.70.101.1.1.13.1.3
The time at which the watchdog last expired, as defined by CIM_Watchdog.TimeOfLastExpiration.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

sunPlatWatchdogMonitoredEntity 1.3.6.1.4.1.42.2.70.101.1.1.13.1.4
The entity monitored by the watchdog, as defined by CIM_Watchdog.MonitoredEntity
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatWatchdogMonitoredEntity  

sunPlatPowerSupplyTable 1.3.6.1.4.1.42.2.70.101.1.1.14
The Power Supply Table extension. This table is valid for an entPhysicalClass of powerSupply(6).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatPowerSupplyEntry

sunPlatPowerSupplyEntry 1.3.6.1.4.1.42.2.70.101.1.1.14.1
An entry in the Power Supply Table extension. Each entry in this table represents a piece of equipment with an entPhysicalClass of powerSupply(6).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatPowerSupplyEntry  

sunPlatPowerSupplyClass 1.3.6.1.4.1.42.2.70.101.1.1.14.1.1
This attribute describes the class of the power supply.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatPowerSupplyClass  

sunPlatBatteryTable 1.3.6.1.4.1.42.2.70.101.1.1.15
The Battery Table extension. This table is valid for a sunPlatPowerSupplyClass of battery(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatBatteryEntry

sunPlatBatteryEntry 1.3.6.1.4.1.42.2.70.101.1.1.15.1
An entry in the Battery Table extension. Each entry in this table represents a piece of equipment with a sunPlatPowerSupplyClass of battery(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatBatteryEntry  

sunPlatBatteryStatus 1.3.6.1.4.1.42.2.70.101.1.1.15.1.1
The current status of the battery as defined for CIM_Battery.BatteryStatus.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatBatteryStatus  

sunPlatLogicalTable 1.3.6.1.4.1.42.2.70.101.1.2.1
An extension to the entLogicalTable. This table is used to define the logical class of the entity. The sunPlatLogicalTable is valid for all entries in the entLogicalTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogicalEntry

sunPlatLogicalEntry 1.3.6.1.4.1.42.2.70.101.1.2.1.1
An entry in the sunPlatLogicalTable extension.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogicalEntry  

sunPlatLogicalClass 1.3.6.1.4.1.42.2.70.101.1.2.1.1.1
This attribute defines the logical class of the entry in the entLogicalTable.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatLogicalClass  

sunPlatLogicalStatus 1.3.6.1.4.1.42.2.70.101.1.2.1.1.2
This attribute describes the current status of the entry in the entLogicalTable as defined by CIM_ManagedSystemElement.Status
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatLogicalStatus  

sunPlatUnitaryComputerSystemTable 1.3.6.1.4.1.42.2.70.101.1.2.2
The Platform Unitary Computer System Table Extension. This table extends the entLogicalTable to provide attributes common to instances of CIM_UnitaryComputerSystem. The sunPlatUnitaryComputerSystemTable is valid for those rows of the entLogicalTable with a SunPlatLogicalClass of computerSystem(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatUnitaryComputerSystemEntry

sunPlatUnitaryComputerSystemEntry 1.3.6.1.4.1.42.2.70.101.1.2.2.1
An entry in the Sun Platform Unitary Computer System Table extension.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatUnitaryComputerSystemEntry  

sunPlatUnitaryComputerSystemPowerState 1.3.6.1.4.1.42.2.70.101.1.2.2.1.1
This attribute displays the computer systems current power state as defined by CIM_UnitaryComputerSystem.PowerState. When this attribute is written to the corresponding power state will be requested from the computer system as provided by the CIM_UnitaryComputerSystem.SetPowerState() method.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatUnitaryComputerSystemPowerState  

sunPlatUnitaryComputerSystemApplySettings 1.3.6.1.4.1.42.2.70.101.1.2.2.1.2
Setting this will cause the settings corresponding to the value to be applied to the instance of CIM_UnitaryComputerSystem represented by this row.
Status: current Access: read-write
OBJECT-TYPE    
  SunPlatUnitaryComputerSystemApplicableSetting  

sunPlatInitialLoadInfoTable 1.3.6.1.4.1.42.2.70.101.1.2.3
The Platform Unitary Computer System Initial Load Info Table extension. This table instruments the CIM_UnitaryComputerSystem.InitialLoadInfo[] property. The sunPlatInitialLoadInfoTable is valid for those rows of the entLogicalTable with a sunPlatLogicalClass of computerSystem(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatInitialLoadInfoEntry

sunPlatInitialLoadInfoEntry 1.3.6.1.4.1.42.2.70.101.1.2.3.1
An entry in the Sun Platform Unitary Computer System Table extension.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatInitialLoadInfoEntry  

sunPlatInitialLoadInfoIndex 1.3.6.1.4.1.42.2.70.101.1.2.3.1.1
A number identifying an entry in the sunPlatInitialLoadInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatIndex  

sunPlatInitialLoadInfoDescr 1.3.6.1.4.1.42.2.70.101.1.2.3.1.2
The name for the information presented in the sunPlatInitialLoadInfoValue for this row.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatInitialLoadInfoCurrentValue 1.3.6.1.4.1.42.2.70.101.1.2.3.1.3
The current contents of an entry in the CIM_UnitaryComputerSystem.InitialLoadInfo[] array.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatInitialLoadInfoDesiredValue 1.3.6.1.4.1.42.2.70.101.1.2.3.1.4
The desired contents of an entry in the CIM_UnitaryComputerSystem.InitialLoadInfo[] array. Setting sunPlatUnitaryComputerSystemApplySettings to a value of specifiedSettings(2) will cause these values to be applied.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

sunPlatLogTable 1.3.6.1.4.1.42.2.70.101.1.3.1
The NIM log table. It is used to maintain a currentProblemList for each managed object as per M.3100, sec. 5.22. The management system creates entries in this table to specify which types of traps, from which managed object, should be logged. Deleting an entry in this table deletes all entries in the corresponding log. There are separate logs for each notification type/managed object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogEntry

sunPlatLogEntry 1.3.6.1.4.1.42.2.70.101.1.3.1.1
Information about a single trap log as defined in X.735 8.1.1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogEntry  

sunPlatLogType 1.3.6.1.4.1.42.2.70.101.1.3.1.1.1
The type of notifications stored in this log. For currentProblemList alarm entries, the sunPlatLogType is set to the sunPlatLogRecordManagedObjectInstance OID value.
Status: current Access: not-accessible
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatLogAdministrativeState 1.3.6.1.4.1.42.2.70.101.1.3.1.1.2
The management system uses this object to stop and start the operations of this object as per X.735, sec. 8.1.1.1.3.
Status: current Access: read-create
OBJECT-TYPE    
  SunPlatLogAdministrativeState  

sunPlatLogOperationalState 1.3.6.1.4.1.42.2.70.101.1.3.1.1.3
Indicates whether or not the log is capable of performing its normal operations as per X.735, sec. 8.1.1.1.4.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatOperationalState  

sunPlatLogFullStatus 1.3.6.1.4.1.42.2.70.101.1.3.1.1.4
If the log is full, this attribute is true.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sunPlatLogCapacityThreshold 1.3.6.1.4.1.42.2.70.101.1.3.1.1.5
Indicates the threshold, expressed in 100ths of a %, at which the log will generate a capacity alarm as per X.735, sec. 8.1.1.3.
Status: current Access: read-create
OBJECT-TYPE    
  SunPlatPercentage  

sunPlatLogRowStatus 1.3.6.1.4.1.42.2.70.101.1.3.1.1.6
This object is used to create a new row or to delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sunPlatLogRecordTable 1.3.6.1.4.1.42.2.70.101.1.3.2
The NIM log record table. It is used to maintain a currentProblemList for each managed object as per M.3100, sec. 5.22.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogRecordEntry

sunPlatLogRecordEntry 1.3.6.1.4.1.42.2.70.101.1.3.2.1
Information about a single notification associated with a specific managed object. Entries in this table are created automatically but can be deleted by the management system. currentProblemList entries are augmented by the sunPlatLogRecordAdditionalEntry and sunPlatLogRecordAlarmEntry tables. They are automatically deleted when the associated alarm condition is cleared. Entries that represent object creation/deletion alarm log types are augmented by the sunPlatLogRecordAdditionalEntry table. Entries that represent alarm log types are also augmented by the sunPlatLogRecordAlarmEntry table. Entries that represent attribute/state change log types are augmented by the sunPlatLogRecordChangeEntry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogRecordEntry  

sunPlatLogRecordId 1.3.6.1.4.1.42.2.70.101.1.3.2.1.1
A unique number identifying this event as per X.735, sec. 8.1.2.2.1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

sunPlatLogRecordLoggingTime 1.3.6.1.4.1.42.2.70.101.1.3.2.1.2
The time at which this trap was logged as per X.735, sec. 8.1.2.2.2.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

sunPlatLogRecordManagedObjectInstance 1.3.6.1.4.1.42.2.70.101.1.3.2.1.3
The object in the entPhysicalTable or entLogicalTable to which this entry applies as defined in X.721, sec. 10.7.4.13. By convention, this is the name of the first object in the row in the table referenced.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

sunPlatLogRecordRowStatus 1.3.6.1.4.1.42.2.70.101.1.3.2.1.4
This object is used to delete an existing row in the table. Note that the only value to which a management system can set this object is destroy(6).
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

sunPlatLogRecordCorrelatedNotifications 1.3.6.1.4.1.42.2.70.101.1.3.2.1.5
A comma-separated list of sunPlatLogRecordId values which identify the other events to which this event is correlated, as defined in X.721, sec 10.7.1.11
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatLogRecordAdditionalTable 1.3.6.1.4.1.42.2.70.101.1.3.3
The NIM Trap Agent additional information table. This table is used to maintain a currentProblemList for each managed object as per M.3100, sec. 5.22.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogRecordAdditionalEntry

sunPlatLogRecordAdditionalEntry 1.3.6.1.4.1.42.2.70.101.1.3.3.1
Information text/OID providing further information relating to alarm and object creation/deletion log records.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogRecordAdditionalEntry  

sunPlatLogRecordAdditionalInfo 1.3.6.1.4.1.42.2.70.101.1.3.3.1.1
An optional OID of an object which provides additional information relevant to this notification as per X.733, sec. 8.1.2.14. This object is only present if it was included in the notification corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatLogRecordAdditionalText 1.3.6.1.4.1.42.2.70.101.1.3.3.1.2
An optional textual description which provides additional information relevant to this notification as per X.733, sec. 8.1.2.13. This object is only present if it was included in the notification corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatLogRecordAlarmTable 1.3.6.1.4.1.42.2.70.101.1.3.4
The NIM Trap Agent logged alarm trap table. This table is used to maintain a currentProblemList for each managed object as per M.3100, sec. 5.22.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogRecordAlarmEntry

sunPlatLogRecordAlarmEntry 1.3.6.1.4.1.42.2.70.101.1.3.4.1
Information about the alarm-specific attributes of a single trap in the log.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogRecordAlarmEntry  

sunPlatLogRecordAlarmPerceivedSeverity 1.3.6.1.4.1.42.2.70.101.1.3.4.1.1
The perceived severity of the alarm, as specified by the agent that generated it in accordance with X.733, sec. 8.1.2.3.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatAlarmPerceivedSeverity  

sunPlatLogRecordAlarmProbableCause 1.3.6.1.4.1.42.2.70.101.1.3.4.1.2
An optional probable cause which provides additional information relevant to this notification as per ITU-T M.3100 sec. 10.2.
Status: current Access: read-only
OBJECT-TYPE    
  SunPlatProbableCause  

sunPlatLogRecordAlarmSpecificProblem 1.3.6.1.4.1.42.2.70.101.1.3.4.1.3
An optional textual description which provides additional information concerning the cause of this notification. If more than one specific problem is described in this object, the problem descriptions are separated by CR LF characters. This object is only present if it was included in the alarm trap corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatLogRecordAlarmRepairAction 1.3.6.1.4.1.42.2.70.101.1.3.4.1.4
A list of recommended repair actions separated by CR LF sequences.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

sunPlatLogRecordChangeTable 1.3.6.1.4.1.42.2.70.101.1.3.5
The NIM Trap Agent logged change trap table. This table is used to maintain extra information for log records that represent attribute or state changes as per X.721, sec. 6.2.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SunPlatLogRecordChangeEntry

sunPlatLogRecordChangeEntry 1.3.6.1.4.1.42.2.70.101.1.3.5.1
Information about the attribute/state change specific attributes of a single trap in the log. Each of the fields will be present according to the type of the attribute changed. State changes will be indicated using the sunPlatLogRecordChangeNewInteger and sunPlatLogRecordChangeOldInteger objects.
Status: current Access: not-accessible
OBJECT-TYPE    
  SunPlatLogRecordChangeEntry  

sunPlatLogRecordChangeChangedOID 1.3.6.1.4.1.42.2.70.101.1.3.5.1.1
The changed object's OBJECT IDENTIFIER value in an attribute/state change notification.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

sunPlatLogRecordChangeNewInteger 1.3.6.1.4.1.42.2.70.101.1.3.5.1.2
The new INTEGER value in an attribute/state change notification.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sunPlatLogRecordChangeOldInteger 1.3.6.1.4.1.42.2.70.101.1.3.5.1.3
The old INTEGER value in an attribute/state change notification.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sunPlatLogRecordChangeNewString 1.3.6.1.4.1.42.2.70.101.1.3.5.1.4
The new OCTET-STRING value in an attribute change notification.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sunPlatLogRecordChangeOldString 1.3.6.1.4.1.42.2.70.101.1.3.5.1.5
The old OCTET-STRING value in an attribute change notification.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sunPlatLogRecordChangeNewOID 1.3.6.1.4.1.42.2.70.101.1.3.5.1.6
The new OBJECT IDENTIFIER value in an attribute change notification.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatLogRecordChangeOldOID 1.3.6.1.4.1.42.2.70.101.1.3.5.1.7
The old OBJECT IDENTIFIER value in an attribute change notification.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatNotificationEventId 1.3.6.1.4.1.42.2.70.101.2.1.1
A unique ID for this notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

sunPlatNotificationTime 1.3.6.1.4.1.42.2.70.101.2.1.2
The time that this notification was generated.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DateAndTime  

sunPlatNotificationObject 1.3.6.1.4.1.42.2.70.101.2.1.3
The object in the entPhysicalTable or the entLogicalTable to which this notification applies. By convention, this is the name of the first object in the row in the table referenced.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  RowPointer  

sunPlatNotificationPerceivedSeverity 1.3.6.1.4.1.42.2.70.101.2.1.4
The perceived severity of the alarm, as specified by the agent that generated it in accordance with X.733, sec. 8.1.2.3.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SunPlatAlarmPerceivedSeverity  

sunPlatNotificationProbableCause 1.3.6.1.4.1.42.2.70.101.2.1.5
An optional probable cause which provides additional information relevant to this notification as per ITU-T M.3100 sec. 10.2.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SunPlatProbableCause  

sunPlatNotificationSpecificProblem 1.3.6.1.4.1.42.2.70.101.2.1.6
An optional textual description which provides additional information concerning the cause of this notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

sunPlatNotificationRepairAction 1.3.6.1.4.1.42.2.70.101.2.1.7
A list of recommended repair actions separated by CR LF sequences.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

sunPlatNotificationAdditionalInfo 1.3.6.1.4.1.42.2.70.101.2.1.8
An optional OID of an object which provides additional information relevant to this notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatNotificationAdditionalText 1.3.6.1.4.1.42.2.70.101.2.1.9
An optional textual description which provides additional information relevant to this notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

sunPlatNotificationChangedOID 1.3.6.1.4.1.42.2.70.101.2.1.10
The changed object's OBJECT IDENTIFIER value in an attribute/state change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  VariablePointer  

sunPlatNotificationNewInteger 1.3.6.1.4.1.42.2.70.101.2.1.11
The new INTEGER value in an attribute/state change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

sunPlatNotificationOldInteger 1.3.6.1.4.1.42.2.70.101.2.1.12
The old INTEGER value in an attribute/state change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

sunPlatNotificationNewString 1.3.6.1.4.1.42.2.70.101.2.1.13
The new OCTET-STRING value in an attribute change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

sunPlatNotificationOldString 1.3.6.1.4.1.42.2.70.101.2.1.14
The old OCTET-STRING value in an attribute change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

sunPlatNotificationNewOID 1.3.6.1.4.1.42.2.70.101.2.1.15
The new OBJECT IDENTIFIER value in an attribute change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatNotificationOldOID 1.3.6.1.4.1.42.2.70.101.2.1.16
The old OBJECT IDENTIFIER value in an attribute change notification.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sunPlatNotificationCorrelatedNotifications 1.3.6.1.4.1.42.2.70.101.2.1.17
A list of sunPlatNotificationEventIDs which are correlated to this notification, separated by commas.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString  

sunPlatObjectCreation 1.3.6.1.4.1.42.2.70.101.2.0.1
Indicates that an object, indicated by sunPlatNotificationObject, has been created as defined in X.721, sec. 13.6.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatObjectDeletion 1.3.6.1.4.1.42.2.70.101.2.0.2
Indicates that an object, indicated by sunPlatNotificationObject, has been deleted as defined in X.721, sec. 13.7.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatCommunicationsAlarm 1.3.6.1.4.1.42.2.70.101.2.0.3
Indicates that a communication alarm has occurred as defined in X.721, sec. 13.2.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatEnvironmentalAlarm 1.3.6.1.4.1.42.2.70.101.2.0.4
Indicates that an environment alarm has occurred as defined in X.721, sec. 13.3.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatEquipmentAlarm 1.3.6.1.4.1.42.2.70.101.2.0.5
Indicates that an equipment alarm has occurred as defined in X.721, sec. 13.4.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatProcessingErrorAlarm 1.3.6.1.4.1.42.2.70.101.2.0.6
Indicates that a processing error alarm has occurred as defined in X.721, sec. 13.10.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatStateChange 1.3.6.1.4.1.42.2.70.101.2.0.7
Indicates that a state change has occurred on the state attribute identified by sunPlatNotificationChangedOID. As states are enumerations of type INTEGER, the old and new states are passed in sunPlatNotificationOldInteger and sunPlatNotificationNewInteger respectively. This is as defined in X.721, sec. 13.14.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatAttributeChangeInteger 1.3.6.1.4.1.42.2.70.101.2.0.8
Indicates that attribute identified by sunPlatNotificationChangedOID has changed from the value in sunPlatNotificationOldInteger to the value in sunPlatNotificationNewInteger. This is as defined in X.721, sec. 13.1.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatAttributeChangeString 1.3.6.1.4.1.42.2.70.101.2.0.9
Indicates that attribute identified by sunPlatNotificationChangedOID has changed from the value in sunPlatNotificationOldString to the value in sunPlatNotificationNewString. This is as defined in X.721, sec. 13.1.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatAttributeChangeOID 1.3.6.1.4.1.42.2.70.101.2.0.10
Indicates that attribute identified by sunPlatNotificationChangedOID has changed from the value in sunPlatNotificationOldOID to the value in sunPlatNotificationNewOID. This is as defined in X.721, sec. 13.1.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatQualityOfServiceAlarm 1.3.6.1.4.1.42.2.70.101.2.0.11
Indicates that a quality of service alarm has occurred as defined in X.721, sec 13.11.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatIndeterminateAlarm 1.3.6.1.4.1.42.2.70.101.2.0.12
Indicates that an alarm of an indeterminate type has occurred.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

sunPlatCompliance 1.3.6.1.4.1.42.2.70.101.3.1.1
The compliance statement for SNMP entities which implement this MIB.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

sunPlatGeneralGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.1
The collection of objects which are independent of the platform(s) being monitored.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatEquipmentGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.2
The collection of objects which are used to represent attributes of the NIM class of Equipment defined in M.3100, sec. 3.2.2.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatEquipmentHolderGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.3
The collection of objects which are used to represent attributes of platform components with an entPhysicalClass of container(5).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatCircuitPackGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.4
The collection of objects which are used to represent attributes of platform components with an entPhysicalClass of module(9).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatPhysicalGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.5
The collection of objects representing attributes of platform components with an entPhysicalClass value of other(1).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatSensorGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.6
The collection of objects representing attributes of platform components with an entPhysicalClass value of sensor(8).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatBinarySensorGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.7
The collection of objects representing attributes of sensors with a sunPlatSensorClass of binary(1).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatNumericSensorGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.8
The collection of objects representing attributes of sensors with a sunPlatSensorClass of numeric(2).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatDiscreteSensorGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.9
The collection of objects representing attributes of sensors with a sunPlatSensorClass of discrete(3).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatFanGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.10
The collection of objects representing attributes of platform components with an entPhysicalClass of fan(7).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatAlarmGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.11
The collection of objects representing attributes of platform components with a sunPlatPhysicalClass of alarm(2).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatWatchdogGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.12
The collection of objects representing attributes of platform components with a sunPlatPhysicalClass of watchdog(3).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatPowerSupplyGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.13
The collection of objects representing attributes of platform components with an entPhysicalClass of powerSupply(6).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatBatteryGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.14
The collection of objects representing attributes of power supplies with a sunPlatPowerSupplyClass of battery(3).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogicalGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.15
The collection of objects representing attributes of logical entities present in the entLogicalTable.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatUnitaryComputerSystemGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.16
The collection of objects representing attributes of logical entities with a sunPlatLogicalClass of computerSystem(2).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.17
The collection of objects representing attributes of logs and/or current problem lists.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogRecordGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.18
The collection of objects representing a log record or current problem.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogRecordAdditionalGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.19
The collection of objects providing additional information relating to a log record or current problem.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogRecordAlarmGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.20
The collection of objects providing information related to an alarm log record or current problem.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatLogRecordChangeGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.21
The collection of objects providing information related to an attribute change log record.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatNotificationObjectGroup 1.3.6.1.4.1.42.2.70.101.3.2.1.22
The collection of objects used in notifications.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

sunPlatNotificationsGroup 1.3.6.1.4.1.42.2.70.101.3.2.2.1
The collection of notifications used to indicate the addition or deletion of managed objects from the model, changes of managed object state, attribute changes and the raising of alarms.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP