SYNC-RESEARCH-MIB

File: SYNC-RESEARCH-MIB.mib (141113 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC-1215
SNMPv2-TC

Imported symbols

enterprises IpAddress Counter
OBJECT-TYPE TRAP-TYPE PhysAddress
DisplayString

Defined Types

CommEntry  
SEQUENCE    
  commIndex INTEGER
  commName OCTET STRING
  commTrap INTEGER
  commIPAddr IpAddress
  commMACAddr OCTET STRING
  commAccess INTEGER

LanControlEntry  
SEQUENCE    
  lanControlIndex INTEGER
  lanControlType INTEGER
  lanStatus INTEGER
  lanControlFailureCode OCTET STRING
  lanControlNAUName DisplayString

LanPortEntry  
SEQUENCE    
  lanPortIndex INTEGER
  lanPortType INTEGER
  lanMACAddress PhysAddress
  lanPROMMACAddress PhysAddress
  lanSpeed INTEGER
  lanT1Timer INTEGER
  lanT2Timer INTEGER
  lanTiTimer INTEGER
  lanRxWindowSize INTEGER
  lanTxWindowSize INTEGER
  lanMaxRetries INTEGER
  lanRingNumber INTEGER
  lanBridgeNumber INTEGER
  lanEthernetFrameFormat INTEGER
  lanSendLocalTest INTEGER
  lanBroadcastType INTEGER
  lanIPAddress IpAddress
  lanNetworkMask IpAddress
  lanDefaultGateway IpAddress
  lanNAUName DisplayString
  lanInterfaceType INTEGER
  lanIPEthernetFrameType INTEGER
  lanInitState INTEGER

LineControlEntry  
SEQUENCE    
  lineControlIndex INTEGER
  lineControlType INTEGER
  lineStatus INTEGER
  lineControlFailureCode OCTET STRING
  lineControlNAUName DisplayString

LinePhysicalEntry  
SEQUENCE    
  linePhysicalIndex INTEGER
  linePhysicalType INTEGER
  lineEIAStatus INTEGER
  lineQualityFrameCount Counter
  lineQualityCRCErrors Counter
  lineQualityAborts Counter

SdlcConfigEntry  
SEQUENCE    
  sdlcConfigPortIndex INTEGER
  sdlcConfigType INTEGER
  sdlcInitState INTEGER
  sdlcCarrier INTEGER
  sdlcClocking INTEGER
  sdlcSpeed INTEGER
  sdlcPause INTEGER
  sdlcNRZI INTEGER
  sdlcT1Timer INTEGER
  sdlcSlowPollTimer INTEGER
  sdlcMaxRetries INTEGER
  sdlcNAUName DisplayString
  sdlcMultiFlagInsertion INTEGER

SdlcStatsEntry  
SEQUENCE    
  sdlcStatsPortIndex INTEGER
  sdlcPortType INTEGER
  sdlcInOctets Counter
  sdlcOutOctets Counter
  sdlcInFrames Counter
  sdlcOutFrames Counter
  sdlcOverruns Counter
  sdlcCRCErrors Counter
  sdlcRecvAborts Counter

BisyncConfigEntry  
SEQUENCE    
  bisyncConfigPortIndex INTEGER
  bisyncConfigType INTEGER
  bisyncNAUName DisplayString
  bisyncInitState INTEGER
  bisyncCarrier INTEGER
  bisyncClocking INTEGER
  bisyncSpeed INTEGER
  bisyncPause INTEGER
  bisyncReplyTimer INTEGER
  bisyncRetries INTEGER
  bisyncSlowpollTimer INTEGER
  bisyncSessTerm INTEGER

BisyncStatsEntry  
SEQUENCE    
  bisyncStatsPortIndex INTEGER
  bisyncPortType INTEGER
  bisyncInOctets Counter
  bisyncOutOctets Counter
  bisyncOverruns Counter
  bisyncCRCErrors Counter
  bisyncRcvTimeout Counter
  bisyncXmtTimeout Counter

FrameRelayConfigEntry  
SEQUENCE    
  frameRelayConfigPortIndex INTEGER
  frameRelayPortType INTEGER
  frameRelayInitState INTEGER
  frameRelayClocking INTEGER
  frameRelaySpeed INTEGER
  frameRelayLocalManagementProtocol INTEGER
  frameRelayLinkPollingTimer INTEGER
  frameRelayFullStatusPollingCount INTEGER
  frameRelayT1Timer INTEGER
  frameRelayT2Timer INTEGER
  frameRelayTiTimer INTEGER
  frameRelayRxWindowSize INTEGER
  frameRelayTxWindowSize INTEGER
  frameRelayMaxRetries INTEGER
  frameRelayNAUName DisplayString
  frameRelayVirtualMACAddress PhysAddress
  frameRelayVirtualRingNumber INTEGER
  frameRelayVirtualBridgeNumber INTEGER
  frameRelayIPAddress IpAddress
  frameRelayNetworkMask IpAddress
  frameRelayDefaultGatewayAddress IpAddress

FrameRelayStatsEntry  
SEQUENCE    
  frameRelayStatsPortIndex INTEGER
  frameRelayInOctets Counter
  frameRelayOutOctets Counter
  frameRelaySampleDuration INTEGER
  frameRelayOverruns Counter
  frameRelayCRCErrors Counter
  frameRelayRecvAborts Counter

PuControlEntry  
SEQUENCE    
  puControlLineIndex INTEGER
  puControlPUAddress OCTET STRING
  puStatus INTEGER
  puConnectionStatus INTEGER
  puLastClearCode OCTET STRING
  puControlFailureCode OCTET STRING
  puControlNAUName DisplayString
  puConnectionAttemptCount Counter

SdlcPuConfigEntry  
SEQUENCE    
  sdlcPuConfigLineIndex INTEGER
  sdlcPuConfigAddress OCTET STRING
  sdlcPuNAUName DisplayString
  sdlcPuInitialState INTEGER
  sdlcPuXID OCTET STRING
  sdlcPuType INTEGER
  sdlcPuGroupPollAddress OCTET STRING
  sdlcPuConnectionID OCTET STRING
  sdlcPuMAXOUT INTEGER
  sdlcPuConnectType INTEGER

SdlcPuStatsEntry  
SEQUENCE    
  sdlcPuStatsLineIndex INTEGER
  sdlcPuStatsAddress OCTET STRING
  sdlcPuInIFrames Counter
  sdlcPuOutIFrames Counter
  sdlcPuInRRFrames Counter
  sdlcPuOutRRFrames Counter
  sdlcPuInRNRFrames Counter
  sdlcPuOutRNRFrames Counter
  sdlcPuInXIDFrames Counter
  sdlcPuOutXIDFrames Counter
  sdlcPuInTESTFrames Counter
  sdlcPuOutTESTFrames Counter
  sdlcPuInSNRMFrames Counter
  sdlcPuOutSNRMFrames Counter
  sdlcPuInDISCFrames Counter
  sdlcPuOutDISCFrames Counter
  sdlcPuInDMFrames Counter
  sdlcPuOutDMFrames Counter
  sdlcPuInUAFrames Counter
  sdlcPuOutUAFrames Counter
  sdlcPuInFRMRFrames Counter
  sdlcPuOutFRMRFrames Counter
  sdlcPuInRDFrames Counter
  sdlcPuOutRDFrames Counter
  sdlcPuInUIFrames Counter
  sdlcPuOutUIFrames Counter
  sdlcPuReTxIFrames Counter
  sdlcPuPollResponseTimeouts Counter

BisyncPuConfigEntry  
SEQUENCE    
  bisyncPuConfigLineIndex INTEGER
  bisyncPuConfigAddress OCTET STRING
  bisyncPuNAUName DisplayString
  bisyncPuInitialState INTEGER
  bisyncPuXID OCTET STRING
  bisyncPuTargetHostType INTEGER
  bisyncPuMaxData INTEGER
  bisyncPuConnectionID OCTET STRING
  bisyncPuConnectType INTEGER

BisyncPuStatsEntry  
SEQUENCE    
  bisyncPuStatsLineIndex INTEGER
  bisyncPuStatsAddress OCTET STRING
  bisyncPuInTransactions Counter
  bisyncPuOutTransactions Counter
  bisyncPuSlowPolls Counter
  bisyncPuPolls Counter

MappingPuConfigEntry  
SEQUENCE    
  mappingPuConfigLineIndex INTEGER
  mappingPuConfigAddress OCTET STRING
  mappingPuSourceSAP OCTET STRING
  mappingPuDestinationSAP OCTET STRING
  mappingPuDestinationMAC PhysAddress
  mappingPuPartnerConfigLineIndex INTEGER
  mappingPuPartnerConfigAddress OCTET STRING
  mappingPuPartnerSourceSAP OCTET STRING
  mappingPuPartnerDestSAP OCTET STRING
  mappingPuPartnerDestMAC PhysAddress
  mappingPuNAU DisplayString
  mappingPuConnectID OCTET STRING
  mappingPuXID OCTET STRING
  mappingPuDirectDLCI OCTET STRING

DeviceControlEntry  
SEQUENCE    
  deviceControlIndex INTEGER
  deviceControlCUIndex INTEGER
  deviceControlAddress OCTET STRING
  deviceStatus INTEGER
  deviceControlFailureCode OCTET STRING

DeviceConfigEntry  
SEQUENCE    
  deviceConfigLineIndex INTEGER
  deviceConfigCUIndex INTEGER
  deviceConfigAddress OCTET STRING
  deviceConfigType INTEGER

DeviceStatsEntry  
SEQUENCE    
  bscDeviceLineIndex INTEGER
  bscDeviceCUIndex INTEGER
  bscDeviceAddress OCTET STRING
  bscDeviceInTransactions Counter
  bscDeviceOutTransactions Counter
  bscDeviceSumCount Counter
  bscDeviceResponseDelaySum Counter
  bscDeviceResponseDelaySqSum Counter

Defined Values

syncResearch 1.3.6.1.4.1.485
OBJECT IDENTIFIER    

syncResearchAgent 1.3.6.1.4.1.485.1
OBJECT IDENTIFIER    

syncProducts 1.3.6.1.4.1.485.1.1
OBJECT IDENTIFIER    

oemProducts 1.3.6.1.4.1.485.1.2
OBJECT IDENTIFIER    

boundary 1.3.6.1.4.1.485.1.1.1
OBJECT IDENTIFIER    

centralSite 1.3.6.1.4.1.485.1.1.2
OBJECT IDENTIFIER    

syncCN2R2b 1.3.6.1.4.1.485.1.1.1.1
OBJECT IDENTIFIER    

syncFN2R2b 1.3.6.1.4.1.485.1.1.1.2
OBJECT IDENTIFIER    

syncCN4R2b 1.3.6.1.4.1.485.1.1.1.3
OBJECT IDENTIFIER    

syncFN4R2b 1.3.6.1.4.1.485.1.1.1.4
OBJECT IDENTIFIER    

syncQN4R2b 1.3.6.1.4.1.485.1.1.1.5
OBJECT IDENTIFIER    

syncCN4R2c 1.3.6.1.4.1.485.1.1.2.1
OBJECT IDENTIFIER    

syncFN4R2c 1.3.6.1.4.1.485.1.1.2.2
OBJECT IDENTIFIER    

syncQN4R2c 1.3.6.1.4.1.485.1.1.2.3
OBJECT IDENTIFIER    

threeCom 1.3.6.1.4.1.485.1.2.1
OBJECT IDENTIFIER    

cableTron 1.3.6.1.4.1.485.1.2.2
OBJECT IDENTIFIER    

chipcom 1.3.6.1.4.1.485.1.2.3
OBJECT IDENTIFIER    

linkConverter 1.3.6.1.4.1.485.1.2.1.1
OBJECT IDENTIFIER    

oemSNACXR2C 1.3.6.1.4.1.485.1.2.2.1
OBJECT IDENTIFIER    

oemSNACXR2W 1.3.6.1.4.1.485.1.2.2.2
OBJECT IDENTIFIER    

oemSNACMR2C 1.3.6.1.4.1.485.1.2.2.3
OBJECT IDENTIFIER    

oemSNACMR2W 1.3.6.1.4.1.485.1.2.2.4
OBJECT IDENTIFIER    

srNodeGroup 1.3.6.1.4.1.485.3
OBJECT IDENTIFIER    

nodeUnitGroup 1.3.6.1.4.1.485.3.1
OBJECT IDENTIFIER    

nodeNetViewPUGroup 1.3.6.1.4.1.485.3.2
OBJECT IDENTIFIER    

nodeBridgeGroup 1.3.6.1.4.1.485.3.3
OBJECT IDENTIFIER    

nodeLANGroup 1.3.6.1.4.1.485.3.4
OBJECT IDENTIFIER    

nodeLineGroup 1.3.6.1.4.1.485.3.5
OBJECT IDENTIFIER    

nodePUGroup 1.3.6.1.4.1.485.3.6
OBJECT IDENTIFIER    

nodeDeviceGroup 1.3.6.1.4.1.485.3.7
OBJECT IDENTIFIER    

unitControlGroup 1.3.6.1.4.1.485.3.1.1
OBJECT IDENTIFIER    

unitStatusGroup 1.3.6.1.4.1.485.3.1.2
OBJECT IDENTIFIER    

unitConfigGroup 1.3.6.1.4.1.485.3.1.3
OBJECT IDENTIFIER    

unitStatisticsGroup 1.3.6.1.4.1.485.3.1.4
OBJECT IDENTIFIER    

netViewPUStatusGroup 1.3.6.1.4.1.485.3.2.1
OBJECT IDENTIFIER    

netViewPUConfigGroup 1.3.6.1.4.1.485.3.2.2
OBJECT IDENTIFIER    

bridgeConfigGroup 1.3.6.1.4.1.485.3.3.1
OBJECT IDENTIFIER    

lanControlGroup 1.3.6.1.4.1.485.3.4.1
OBJECT IDENTIFIER    

lanTokenRingGroup 1.3.6.1.4.1.485.3.4.2
OBJECT IDENTIFIER    

lineControlGroup 1.3.6.1.4.1.485.3.5.1
OBJECT IDENTIFIER    

linePhysicalGroup 1.3.6.1.4.1.485.3.5.2
OBJECT IDENTIFIER    

lineSDLCGroup 1.3.6.1.4.1.485.3.5.3
OBJECT IDENTIFIER    

lineBisyncGroup 1.3.6.1.4.1.485.3.5.4
OBJECT IDENTIFIER    

lineFrameRelayGroup 1.3.6.1.4.1.485.3.5.5
OBJECT IDENTIFIER    

puControlGroup 1.3.6.1.4.1.485.3.6.1
OBJECT IDENTIFIER    

puSDLCGroup 1.3.6.1.4.1.485.3.6.2
OBJECT IDENTIFIER    

puBisyncGroup 1.3.6.1.4.1.485.3.6.3
OBJECT IDENTIFIER    

puMappingGroup 1.3.6.1.4.1.485.3.6.4
OBJECT IDENTIFIER    

deviceControlGroup 1.3.6.1.4.1.485.3.7.1
OBJECT IDENTIFIER    

deviceBSCGroup 1.3.6.1.4.1.485.3.7.2
OBJECT IDENTIFIER    

srCommTrapGroup 1.3.6.1.4.1.485.2
OBJECT IDENTIFIER    

commCount 1.3.6.1.4.1.485.2.1
The number of possible community name entries in the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

commTable 1.3.6.1.4.1.485.2.2
This table houses the information for trivial authentication and sending traps.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CommEntry

commEntry 1.3.6.1.4.1.485.2.2.1
Each entry contains a community name and access code for SNMP trivial authenticationm an enable/disable traps options, as well as network and physical addressing information for traps.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CommEntry  

commIndex 1.3.6.1.4.1.485.2.2.1.1
A unique value for each community entry. Its value ranges between 1 and commCount.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

commName 1.3.6.1.4.1.485.2.2.1.2
A community name that will be used to access MIB objects within the device. Each community name is associated with an access code of either NO_ACCESS, RO, RW, or SU.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

commTrap 1.3.6.1.4.1.485.2.2.1.3
This object is checked to determine if traps should be sent to the corresponding network address associated with it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER trapoff(1), trapon(2)  

commIPAddr 1.3.6.1.4.1.485.2.2.1.4
The network address of the device that will receive traps from the agent. This IP address also qualifies who may use this community name to access MIB objects. If this community name is use by some one with a different IP address, an Authentication Trap will be generated. If the IP address is set to 0.0.0.0, anyone may use this address, however, traps will not be sent since the address is invalid.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

commMACAddr 1.3.6.1.4.1.485.2.2.1.5
The physical address of the device receiving traps from the agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

commAccess 1.3.6.1.4.1.485.2.2.1.6
Access code assiciated with the community name of the same entry. noAccess indicates a community name with zero privileges. ro has read-only access to MIB objects. rw allows you to read and write MIB objects. SU (super- user) gives you privileges to read and write any MIB object. The community table itself can only be written to with an access of SU as well as the setting of the IP Address on a device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAccess(1), ro(2), rw(3), su(4)  

unitRestart 1.3.6.1.4.1.485.3.1.1.1
Setting this variable to a value of 1 will force the unit to restart. Setting this variable to any other value will cause an SNMP error. This variable always returns a value of 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER restart-unit(1), dummy-restart(2)  

dumpOnRestart 1.3.6.1.4.1.485.3.1.1.2
Setting this variable to a value of 1 will force the unit to perform a dump on restart. Setting this variable to a value of 2 will force it to not to dump on restart.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dump-on-start(1), dont-dump(2)  

initiateInstall 1.3.6.1.4.1.485.3.1.1.3
Setting this variable to a value of 1 will force the unit to initiate an install process. This variable always returns a value of 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER start-install(1), dummy-install(2)  

initializeStats 1.3.6.1.4.1.485.3.1.1.4
Setting this variable to a value of 1 will force the unit to initialize (clear) all statistics kept by the unit. This variable always returns a value of 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER init-stats(1), dummy-init-stats(2)  

clearDump 1.3.6.1.4.1.485.3.1.1.5
Setting this variable to a value of 1 will force the unit to clear a dump. This variable always returns a value of 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clear-dump-file(1), dummy-clear(2)  

unitModel 1.3.6.1.4.1.485.3.1.2.1
This variable defines the base hardware model of the unit: A boundary platform is the 486 single board unit. A LIC is the Central Site chassis card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER boundary(1), lic(2), chipcomPED(3), snacMIM(4), microMac(5)  

softwareVersion 1.3.6.1.4.1.485.3.1.2.2
The current version number of the operating software in xx.yyy where xx = major release, yyy = revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..6)  

productType 1.3.6.1.4.1.485.3.1.2.3
The product type string returned is set in the MS.SYS file and defines the product.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

maxPortNumber 1.3.6.1.4.1.485.3.1.2.4
The maximum number of ports this unit can support (total number of serial access ports plus total number of LAN ports).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

maxPU 1.3.6.1.4.1.485.3.1.2.5
The maximum number of PUs this unit can support (total number that can be configured).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

maxSession 1.3.6.1.4.1.485.3.1.2.6
The maximum number of sessions this unit can support (total number that can be configured).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

maxDevice 1.3.6.1.4.1.485.3.1.2.7
The maximum number of devices this unit can support (total number that can be configured).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

msBoardType 1.3.6.1.4.1.485.3.1.2.8
Indicates the type of serial I/O ports on main board. It returns 1 if not expected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-expected(1), two-port-RS232(16), two-port-RS422(17), two-port-V35(18), v35-RS232(22), rs422-RS232(23)  

msExtBoardType 1.3.6.1.4.1.485.3.1.2.9
Indicates the type of serial I/O ports on extension board. It returns 1 if not present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-present(1), two-port-RS232(19), two-port-RS422(20), two-port-V35(21), two-port-hspeedRS232(24), two-port-hspeedV35(25)  

dumpFileStatus 1.3.6.1.4.1.485.3.1.2.10
Indicates the presence of a dump file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), dump-available(2)  

dumpFileName 1.3.6.1.4.1.485.3.1.2.11
The dump file name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..11)  

unitSerialNumber 1.3.6.1.4.1.485.3.1.2.12
The base unit serial number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..9)  

expansionSerialNumber 1.3.6.1.4.1.485.3.1.2.13
The expansion board serial number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..9)  

romVersion 1.3.6.1.4.1.485.3.1.2.14
The ROM version number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

processorType 1.3.6.1.4.1.485.3.1.2.15
The base unit processor type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER i286(1), i386(2), i486SX(3), i486DX(4)  

chassisSlot 1.3.6.1.4.1.485.3.1.2.16
If the unit is a blade in a chassis, then this variable indicates the slot number. If not applicable, a value of 99 will be returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

lastTrapSeqNumber 1.3.6.1.4.1.485.3.1.2.17
This entry contains the last sequence number of the last trap generated by the unit. When this value reaches its maximum, it then rolls back to 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

lastInstallErrCode 1.3.6.1.4.1.485.3.1.2.18
This entry contains the status of last install. If the last install was successful, 0 is returned, 9999 indicates installation is in progress, otherwise an error code is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..9999  

unitPartNumber 1.3.6.1.4.1.485.3.1.2.19
The base unit part number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..19)  

expansionPartNumber 1.3.6.1.4.1.485.3.1.2.20
The expansion board part number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..19)  

unitId 1.3.6.1.4.1.485.3.1.3.1
This is the unit id. It consists of a 1 to 8 octet right justified case-sensitive ASCII field which uniquely identifies the unit. This ID is displayed on the LCD display, all system dumps, and any ASCII alarms. The defalult value for this field is startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

nmsSerialSpeed 1.3.6.1.4.1.485.3.1.3.2
The async serial port speed for NMS console port. The speed is expressed in bits per second (i.e. 9.6 Kbps is represented as 96 decimal). Currently supported speeds are: 1200 2400 4800 9600 19200 Default speed is 9600 bits per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER speed1200(12), speed2400(24), speed4800(48), speed9600(96), speed19200(192)  

serialPortLogoffTimer 1.3.6.1.4.1.485.3.1.3.3
Units are minutes. Default value is 0, indicating that no timer is active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..60  

callRetryTimer 1.3.6.1.4.1.485.3.1.3.4
The call retry timer (a.k.a Session Retry Timer). The number of seconds to wait before trying to retry a failed LLC connection attempt. Currently supported values are 2 - 999 seconds. The default is 30 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..999  

password 1.3.6.1.4.1.485.3.1.3.5
The unit's password. This field indicates the system password used to log into the unit for operating the NMS interface. This field is a one to eight byte case-sensitive left justified ASCII data field and may not be left blank. The default value is 'sri' (for Sync Research Inc.).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..8)  

configPassword 1.3.6.1.4.1.485.3.1.3.6
The configuration password. This field indicates the password used to enter the configuration subsystem. This field is a one to eight byte case-sensitive left justified ASCII data field and may not be left blank. The default value is 'sri' (for Sync Research Inc.).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..8)  

dateTimeField 1.3.6.1.4.1.485.3.1.3.7
The date and time. This field is stored as 6 bytes of BCD Data in the following order: Month: 0x01 - 0x12 Day: 0x01 - 0x31 Year: 0x00 - 0x99 Hour: 0x00 - 0x23 Minute: 0x00 - 0x59 Second: 0x00 - 0x59
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

configId 1.3.6.1.4.1.485.3.1.3.8
The configuration identifer. This field is the configuration ID assigned when a new configuration is activated for the first time. It is assigned by the unit automatically and is not user assignable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

internalMacAddress 1.3.6.1.4.1.485.3.1.3.9
Embedded conversion node MAC address. Applicable to Frame Node only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

internalRingNumber 1.3.6.1.4.1.485.3.1.3.10
Embedded conversion node ring number. This should be unique within the network. Applicable to Frame Node only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

internalBridgeNumber 1.3.6.1.4.1.485.3.1.3.11
Embedded conversion node bridge number. This parameter is currently not used. Applicable to Frame Node only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..15  

numberSamples 1.3.6.1.4.1.485.3.1.4.1
The number of internal system level samples performed. Samples are taken every 10th of a second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

systemBufferFreeCounts 1.3.6.1.4.1.485.3.1.4.2
The average number of system buffers free in the system during the system sample period. The number of available buffers varies by system type and configuration. To determine the maximum number of buffers for a given configuration, view a sample when there is no activity in the unit. A heavily loaded unit will display a small number of available buffers and low Processor Idle counts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuIdleSumCounts 1.3.6.1.4.1.485.3.1.4.3
The main processor average idle sum count. This is the average number of times the idle counter was incremented over the sampling period divided by 1000. This is an absolute value of performance as does not vary by performance. A heavily loaded unit will display a small number of available buffers and low Processor Idle counts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netviewConnectionStatus 1.3.6.1.4.1.485.3.2.1.1
The status of the Primary Netview Connection
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), not-connected(2)  

netviewLastClearCode 1.3.6.1.4.1.485.3.2.1.2
A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed primary NetView connection attempt (a.k.a. call attempt) or Netview active connection (a.k.a. session). For LLC type 2 connections the first octet (cause) is always 0. The second octet (diagnostic) indicates the reason for the last connection failure. The second octet is set to 0 when a sucessful call has been placed, or if no call has ever been placed (e.g. PU never came up). If the second octet is non-zero then it indicates the reason for the connection attempt failure. See current product documentation for list of possible values.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

netviewAltConnectionStatus 1.3.6.1.4.1.485.3.2.1.3
The status of the alternate Netview Connection
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), not-connected(2)  

netviewAltLastClearCode 1.3.6.1.4.1.485.3.2.1.4
A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed alternate NetView connection attempt (a.k.a. call attempt) or Netview active connection (a.k.a. session). For LLC type 2 connections the first octet (cause) is always 0. The second octet (diagnostic) indicates the reason for the last connection failure. The second octet is set to 0 when a sucessful call has been placed, or if no call has ever been placed (e.g. PU never came up). If the second octet is non-zero then it indicates the reason for the connection attempt failure. See current product documentation for list of possible values.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

netviewConnectionAttemptCount 1.3.6.1.4.1.485.3.2.1.5
The number of connection attempts performed on the Primary NetView PU. This count is set to zero at startup, and after every loss of an estabished session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netviewAltConnectionAttemptCount 1.3.6.1.4.1.485.3.2.1.6
The number of connection attempts performed on the Alternate NetView PU. This count is set to zero at startup, and after every loss of an estabished session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netviewPUXID 1.3.6.1.4.1.485.3.2.2.1
Primary NetView PU XID. This field indicates the XID data to be sent to the host for establishing Netview Session. This field is a maximum four byte hexadecimal data field. This field should be set to all zeroes if no Netview session is to be established. The default value is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

alternateNetviewPUXID 1.3.6.1.4.1.485.3.2.2.2
Alternate NetView PU XID. This field indicates the XID data to be sent to the host for establishing Netview Session. This field is a maximum four byte hexadecimal data field. This field should be set to all zeroes if no Netview session is to be established. The default value is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

netviewConnectID 1.3.6.1.4.1.485.3.2.2.3
The primary NetView PU connection ID. The default value is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

alternateNetviewConnectID 1.3.6.1.4.1.485.3.2.2.4
The alternate NetView PU connection ID. The default value is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

netviewSpecialConnect 1.3.6.1.4.1.485.3.2.2.5
The primary NetView PU connection type. The default value is originate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

alternateNetviewSpecialConnect 1.3.6.1.4.1.485.3.2.2.6
The alternate NetView PU connection type. The default value is originate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

brEnableBridging 1.3.6.1.4.1.485.3.3.1.1
This flag indicates if bridging is to be performed on this unit. The default value for this field is 'No'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

bridgePriority 1.3.6.1.4.1.485.3.3.1.2
Sometimes referred to as the ROOT id. Determines the priority component of the Bridge identifier used in determining the Root Bridge for a spanning tree network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

brMaxAge 1.3.6.1.4.1.485.3.3.1.3
The time at which a configuration message is descarded. Units are in seconds. Default value is 10 seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 6..40  

brHelloTimer 1.3.6.1.4.1.485.3.3.1.4
The time interval between issuing configuration messages. Units are seconds. Default value is 2 seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

brFilterIPX 1.3.6.1.4.1.485.3.3.1.5
If set to yes, all IPX frames are filtered (if bridge is enabled). Default is Yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brFilterIP 1.3.6.1.4.1.485.3.3.1.6
If set to yes, all IP frames are filtered (if bridging is enabled). Default is Yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brFilterNetBIOS 1.3.6.1.4.1.485.3.3.1.7
If set to yes, all NetBIOS frames are filtered (if bridging is enabled). Default is Yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brFilterLLC2 1.3.6.1.4.1.485.3.3.1.8
If set to yes, all LAN attached SNA LLC2 frames are filtered (if bridging is enabled). Default is Yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brFilterSMAN 1.3.6.1.4.1.485.3.3.1.9
If set to yes, all SyncManager LLC2 frames are filtered (if bridging is enabled). Default is Yes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brForwardOther 1.3.6.1.4.1.485.3.3.1.10
If set to yes, all other frames are forwarded (if bridging is enabled). Default is No.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

brIPXtargetPort 1.3.6.1.4.1.485.3.3.1.11
If IPX filtering is set to no, then this parameter defines a specific FR port to deliver IPX frames to. Used in conjunction with brIPXtargetDLCI. The valid range is 0 to 5. A value of 0 indicates that the IPX target port/DLCI is not configured. This field has the default value of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brIPXtargetDLCI 1.3.6.1.4.1.485.3.3.1.12
If IPX filtering is set to no, then this parameter defines a specific FR DLCI to deliver IPX frames to. Used in conjunction with brIPXtargetPort. If the value of brIPXtargetport is 0, then the value of brIPXtargetDLCI is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

brIPtargetPort 1.3.6.1.4.1.485.3.3.1.13
If IP filtering is set to no, then this parameter defines a specific FR port to deliver IP frames to. Used in conjunction with brIPtargetDLCI. The valid range is 0 to 5. A value of 0 indicates that the IP target port/DLCI is not configured. This field has the default value of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brIPtargetDLCI 1.3.6.1.4.1.485.3.3.1.14
If IP filtering is set to no, then this parameter defines a specific FR DLCI to deliver IP frames to. Used in conjunction with brIPtargetPort. If the value of brIPtargetport is 0, then the value of brIPtargetDLCI is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brNetBIOStargetPort 1.3.6.1.4.1.485.3.3.1.15
If NetBIOS filtering is set to no, then this parameter defines a specific FR port to deliver NetBIOS frames to. Used in conjunction with brNetBIOStargetDLCI. The valid range is 0 to 5. A value of 0 indicates that the NetBIOS target port/DLCI is not configured. This field has the default value of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brNetBIOStargetDLCI 1.3.6.1.4.1.485.3.3.1.16
If NetBIOS filtering is set to no, then this parameter defines a specific FR DLCI to deliver NetBIOS frames to. Used in conjunction with brNetBIOStargetPort. If the value of brNetBIOStargetport is 0, then the value of brNetBIOStargetDLCI is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brLLC2targetPort 1.3.6.1.4.1.485.3.3.1.17
If SNA LLC2 filtering is set to no, then this parameter defines a specific FR port to deliver LLC2 frames to. Used in conjunction with brLLC2targetDLCI. The valid range is 0 to 5. A value of 0 indicates that the brLLC2targetport/brLLC2targetDLCI is not configured. This field has the default value of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brLLC2targetDLCI 1.3.6.1.4.1.485.3.3.1.18
If SNA LLC2 filtering is set to no, then this parameter defines a specific FR DLCI to deliver LLC2 frames to. Used in conjunction with brLLC2targetPort. If the value of brLLC2targetport is 0, then the value of brLLC2targetDLCI is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brOthertargetPort 1.3.6.1.4.1.485.3.3.1.19
If Other forwarding is set to yes, then this parameter defines a specific FR port to deliver Other frames to. Used in conjunction with brOthertargetDLCI. The valid range is 0 to 5. The value 0 indicates that the brOthertargetport/brOthertargetDLCI is not configured. This field has the default value of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brOthertargetDLCI 1.3.6.1.4.1.485.3.3.1.20
If Other forwarding is set to yes, then this parameter defines a specific FR DLCI to deliver Other frames to. Used in conjunction with brOthertargetPort. If the value of brOthertargetport is 0, then the value of brOthertargetDLCI is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brSerialPriority 1.3.6.1.4.1.485.3.3.1.21
This parameter defines the transmit priority for Frame Relay of serial attached port traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brTerminatedLLC2Priority 1.3.6.1.4.1.485.3.3.1.22
This parameter defines the transmit priority for Frame Relay of terminated LLC2 traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brLLC2Priority 1.3.6.1.4.1.485.3.3.1.23
This parameter defines the transmit priority for Frame Relay of SNA LLC2 traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brIPXPriority 1.3.6.1.4.1.485.3.3.1.24
This parameter defines the transmit priority for Frame Relay of IPX traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brIPPriority 1.3.6.1.4.1.485.3.3.1.25
This parameter defines the transmit priority for Frame Relay of IP traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brNetBIOSPriority 1.3.6.1.4.1.485.3.3.1.26
This parameter defines the transmit priority for Frame Relay of NetBIOS traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brOtherPriority 1.3.6.1.4.1.485.3.3.1.27
This parameter defines the transmit priority for Frame Relay of other traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER urgent(1), high(2), medium(3), low(4)  

brHighPriorityBandwidth 1.3.6.1.4.1.485.3.3.1.28
This parameter defines the high priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 40.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

brMediumPriorityBandwidth 1.3.6.1.4.1.485.3.3.1.29
This parameter defines the medium priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

brLowPriorityBandwidth 1.3.6.1.4.1.485.3.3.1.30
This parameter defines the low priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 20.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

lanControlTable 1.3.6.1.4.1.485.3.4.1.1
A table for controlling LAN ports and obtaining information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LanControlEntry

lanControlEntry 1.3.6.1.4.1.485.3.4.1.1.1
An entry consisting of port information for a particular LAN port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LanControlEntry  

lanControlIndex 1.3.6.1.4.1.485.3.4.1.1.1.1
The number that uniquely identifies this LAN port. Currently only one LAN port per unit is supported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lanControlType 1.3.6.1.4.1.485.3.4.1.1.1.2
The LAN type. Token-Ring ports run the IEEE 802.5 protocol. Ethernet-type run the IEEE 802.3 and Ethernet Version 2. Other LAN protocols may be added in the future.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER token-ring-type(21), ethernet-type(17)  

lanStatus 1.3.6.1.4.1.485.3.4.1.1.1.3
The status of the port. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. Commands: An enable command will attempt to bring up the LAN. An enable all command will perform the same function as enable, since there are no sub elements on a LAN. A disable command will disable the LAN. Status: Enable(d) indicates the LAN is enabled and running. Disable(d) indicates the LAN has been disabled. Failed indicates the LAN is enabled and not Running.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), failed(3), restart(4)  

lanControlFailureCode 1.3.6.1.4.1.485.3.4.1.1.1.4
This entry contains the failure codes if the associated LAN interface is in the failed state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

lanControlNAUName 1.3.6.1.4.1.485.3.4.1.1.1.5
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

lanPortTable 1.3.6.1.4.1.485.3.4.2.1
A table of LAN information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LanPortEntry

lanPortEntry 1.3.6.1.4.1.485.3.4.2.1.1
An entry consisting of port information for a particular LAN port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LanPortEntry  

lanPortIndex 1.3.6.1.4.1.485.3.4.2.1.1.1
The port number that uniquely identifies this port. Currently only one LANtoken ring port per unit is supported with the port index = 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lanPortType 1.3.6.1.4.1.485.3.4.2.1.1.2
The LAN port type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER token-ring-type(21), ethernet-type(17)  

lanMACAddress 1.3.6.1.4.1.485.3.4.2.1.1.3
The user configured LANtoken ring MAC address. If the address is set to 0 then the burned-in Address is used. This field contains a user configured address if any. If a user configured address is desired, then it must be configured as a valid individual, user defined - MAC address. The address must be configured in the native format convention used by the LAN port. For token Ring LAN ports the address follows User configured addresses must follow IEEE 802.5 IEEE 802.5 rules (most significant bit transmitted first) and must be between 400000000000 and 7FFFFFFFFFFF hexadecimal inclusive. For Ethernet LAN ports the format is must follow IEEE 802.3 rules.where the two least significant bits of the first octet must be zero. This means the first octet must be in the set of numbers 0x00, 0x04, 0x08, ... 0xFC..... The Default Value for this field is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

lanPROMMACAddress 1.3.6.1.4.1.485.3.4.2.1.1.4
The burned in MAC address. This is the MAC address assigned by the factory when the unit is shipped. If the User configured address is set to 0, then this will be the address used by the adapter for the source address field for all frames sent by the LAN adapter. The format ordering of bits is as defined in IEEE 802.5. This ordering is where the Most Significant Bit is transmitted first. This is different from other protocols (e.g. 802.3) where the least significant bit is transmitted first. The representation of the MAC address is in the format native for the LAN port. Boundary platform Token-Ring LAN ports start with the first six digits (three octects) equal to 0002F6 which indicates a Sync Research Token Ring MAC address. Boundary platform Ethernet LAN ports start with the first six digits (three octects) equal to to 00406F which indicates a Sync Research Ethernet MAC address. This field is not changable via any commands and will always contain the manufactured MAC address for the LAN port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

lanSpeed 1.3.6.1.4.1.485.3.4.2.1.1.5
The LAN port speed in Megabits/second. For Token-Ring boundary platforms, the speed is changable via the front panel keypad and LCD menus, and NMS console port. For Token-Ring LIC the speed is changed by a jumper on the back of the board (top two pins = 4, bottom two pins = 16). For Ethernet boundary platforms and LIC, the speed is not configurable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER speed-4Mbs(4), speed-10Mbs(10), speed-16Mbs(16)  

lanT1Timer 1.3.6.1.4.1.485.3.4.2.1.1.6
The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 seconds. The default value for this field is 3 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..25  

lanT2Timer 1.3.6.1.4.1.485.3.4.2.1.1.7
The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be sent for every I frame received. Current supported values are 0 and 2-50. T2 should be less than T1. The default value for this field is 0 (disabled).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..50  

lanTiTimer 1.3.6.1.4.1.485.3.4.2.1.1.8
The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 seconds. The default value for this field is 30 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..50  

lanRxWindowSize 1.3.6.1.4.1.485.3.4.2.1.1.9
The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3 which is the number of I frames received before an RR frame is sent (defined as N3 in IEEE 802.2 LLC). Current allowable values are 1-7. The default value for this field is 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7  

lanTxWindowSize 1.3.6.1.4.1.485.3.4.2.1.1.10
The defalut LLC transmit window size. Current allowable values are 1-7. The default value for this field is 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7  

lanMaxRetries 1.3.6.1.4.1.485.3.4.2.1.1.11
The default LLC maximum number of retries (N2 value). Current allowable values are 1-99. The default value for this field is 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

lanRingNumber 1.3.6.1.4.1.485.3.4.2.1.1.12
802.5 bridging parameter. This variable returns a value of 0, if it is not defined. This value is not applicable to Ethernet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..4095  

lanBridgeNumber 1.3.6.1.4.1.485.3.4.2.1.1.13
802.5 bridging parameter. The default value for this field is 1. This value is not applicable to Ethernet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..15  

lanEthernetFrameFormat 1.3.6.1.4.1.485.3.4.2.1.1.14
The Ethernet frame format used on this LAN. The default value for this field is 802.3. Not used if Token Ring, and 1 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), e802-3-type(2), ethernet-type-2(3)  

lanSendLocalTest 1.3.6.1.4.1.485.3.4.2.1.1.15
This port's send local test option. Identifies whether a test frame should be sent on the local ring to discover a destination MAC address. If all destinations for the unit are located on a remote ring, setting this field to No allows the unit to bypass discovery of a destination MAC address on the local ring. If this field is set to 'No' then the broadcastType field must be set to all routes or single route broadcast. If the any destination is on a local ring or unknown, this parameter should be set to 'Yes'. The default value for this field is 'Yes'. Not used if Ethernet, and 1 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), yes(2), no(3)  

lanBroadcastType 1.3.6.1.4.1.485.3.4.2.1.1.16
This port's broadcast type. Not used if Ethernet. Types are: none, all-routes, and single-route. Identifies the form of a broadcast test frame sent to discover the route to a destination MAC address. If all destinations are located on the local ring, this field may be set to 'None' to prevent a broadcast search for a destination MAC address. If set to 'None', then the sendLocalTest field must be set to 'Yes'. If set as 'All-routes', the unit will send an All-routes broadcast TEST command frame and expect a non-broadcast TEST response frame in return. If set to Single-route, the unit will send a Single-route broadcast TEST command frame and expect a all-routes TEST response frame in return. The default for this field is all routes broadcast. Not used if Ethernet, and 1 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), none-bc(2), all-bc(3), single-bc(4)  

lanIPAddress 1.3.6.1.4.1.485.3.4.2.1.1.17
This is the IP Address of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lanNetworkMask 1.3.6.1.4.1.485.3.4.2.1.1.18
This is the network mask to be used on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lanDefaultGateway 1.3.6.1.4.1.485.3.4.2.1.1.19
Default gateway address to be used when sending responses on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lanNAUName 1.3.6.1.4.1.485.3.4.2.1.1.20
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

lanInterfaceType 1.3.6.1.4.1.485.3.4.2.1.1.21
This port's physical interface type. Only used if Ethernet. The default for this field is utp. Not used if Token Ring, and 1 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), aui(2), bnc(3), utp(4)  

lanIPEthernetFrameType 1.3.6.1.4.1.485.3.4.2.1.1.22
The IP Ethernet frame format used on this LAN for IP frames. The default value for this field is 802.3. Not used if Token Ring, and 1 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), e802-3-type(2), ethernet-type-2(3)  

lanInitState 1.3.6.1.4.1.485.3.4.2.1.1.23
The initial state of the LAN port. If configured for 'in-service', then the LAN port will be brougt up automattically when the unit is powered up. If configured for 'out-of-service', the the LAN port must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'enabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

lineControlTable 1.3.6.1.4.1.485.3.5.1.1
A table for controlling lines and obtaining information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LineControlEntry

lineControlEntry 1.3.6.1.4.1.485.3.5.1.1.1
An entry consisting of port information for a particular port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LineControlEntry  

lineControlIndex 1.3.6.1.4.1.485.3.5.1.1.1.1
The port number that uniquely identifies this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lineControlType 1.3.6.1.4.1.485.3.5.1.1.1.2
The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports emulate a line with Terminal Controllers (PUs) and respond to polls from the Host or upstream PU. TBSC (Terminal Bisync) ports emulate a Host and poll the downstream CUs (e.g. 3274 or ATM Bisync controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal Controllers (CUs) and respond to polls from the Host or upstream CU. Frame Relay ports support Frame Relay PVC. Future line types (e.g. X.25) may be added here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hbsc-type(1), tbsc-type(2), hsdlc-type(11), tsdlc-type(12), frameRelay-type(19)  

lineStatus 1.3.6.1.4.1.485.3.5.1.1.1.3
The status of the port. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. Commands: An enable command will attempt to bring up the line. An enable all command will attempt to bring up the line and any lower layer entities (e.g. PUs). A disable command will disable the line. Status: Enable(d) indicates the line is enabled and running. Disable(d) indicates the line has been disabled. Failed indicates the line is enabled and not Running.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), failed(3), restart(4), enable-all(5)  

lineControlFailureCode 1.3.6.1.4.1.485.3.5.1.1.1.4
This entry contains the failure codes if the associated port interface is in the failed state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

lineControlNAUName 1.3.6.1.4.1.485.3.5.1.1.1.5
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

linePhysicalTable 1.3.6.1.4.1.485.3.5.2.1
A table for obtaining physical signal status information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinePhysicalEntry

linePhysicalEntry 1.3.6.1.4.1.485.3.5.2.1.1
An entry consisting of port information for a particular port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LinePhysicalEntry  

linePhysicalIndex 1.3.6.1.4.1.485.3.5.2.1.1.1
The port number that uniquely identifies this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

linePhysicalType 1.3.6.1.4.1.485.3.5.2.1.1.2
The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports emulate a line with Terminal Controllers (PUs) and respond to polls from the Host or upstream PU. TBSC (Terminal Bisync) ports emulate a Host and poll the downstream CUs (e.g. 3274 or ATM Bisync controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal Controllers (CUs) and respond to polls from the Host or upstream CU. Frame Relay ports support Frame Relay PVC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tbsc-type(1), hbsc-type(2), frameRelay-type(19), hsdlc-type(11), tsdlc-type(12)  

lineEIAStatus 1.3.6.1.4.1.485.3.5.2.1.1.3
A port's current control signal status. All SDLC ports have the ability to read the current status of RS-232 or equivalent control signals. The value returned is a 16 bit value where each bit signifies a signal status where 1 means the signal is active and 0 means the signal is inactive. The value returned is a snapshot taken when the command actually is sent to the driver software and wherever possible actually goes out to the driver or receiver control chips to get the value. Currently defined bit values are as follows*: 128 : Data Terminal Ready 0x0080 RS-232 pin 20 64 : Data Set Ready 0x0040 RS-232 pin 6 32 : Clear to Send 0x0020 RS-232 pin 5 16 : Clear to Send Ext. 0x0010 RS-232 pin 11** 8 : Data Carrier Detect 0x0008 RS-232 pin 8 4 : Busy Out 0x0004 RS-232 pin 25 2 : Request to send 0x0002 RS-232 pin 4 1 : Ring Indicator 0x0001 RS-232 pin 22 Note*: Bit values higher than 128 are reserved for future use. Note**: Clear to Send External is extended (non- standard) pin and reserved for future use by Sync Research.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

lineQualityFrameCount 1.3.6.1.4.1.485.3.5.2.1.1.4
This entry contains the number of frames received. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQualityAborts exceeds 5. When this value reaches its maximum, it then rolls back to 0. Applicable to SDLC only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lineQualityCRCErrors 1.3.6.1.4.1.485.3.5.2.1.1.5
This entry contains the number of frames with CRC errors. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQualityAborts exceeds 5. Applicable to SDLC only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lineQualityAborts 1.3.6.1.4.1.485.3.5.2.1.1.6
This entry contains the number of aborts received. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQualityAborts exceeds 5. Applicable to SDLC only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcConfigTable 1.3.6.1.4.1.485.3.5.3.1
A table of SDLC information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcConfigEntry

sdlcConfigEntry 1.3.6.1.4.1.485.3.5.3.1.1
An entry consisting of port information for a particular SDLC port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SdlcConfigEntry  

sdlcConfigPortIndex 1.3.6.1.4.1.485.3.5.3.1.1.1
The port number that uniquely identifies this port. Current supported SDLC numbers are 1-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcConfigType 1.3.6.1.4.1.485.3.5.3.1.1.2
The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports emulate a line with Terminal Controllers (PUs) and respond to polls from the Host or upstream PU. Note that all ports must currently be defined as the same time for a given unit (i.e. no mixing of HSDLC and TSDLC ports is allowed).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hsdlc-type(11), tsdlc-type(12)  

sdlcInitState 1.3.6.1.4.1.485.3.5.3.1.1.3
The initial state of the SDLC port. If configured for 'in-service', then the SDLC port will be brougt up automattically when the unit is powered up. If configured for 'out-of-service', the the SDLC port must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'enabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

sdlcCarrier 1.3.6.1.4.1.485.3.5.3.1.1.4
This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked), or Request To Send (a.k.a. RTS, RS-232 pin 4) is constant or switched. This parameter also affects SDLC flag generation. If configured for constant then the line will transmit flags in an idle (no data being sent) state. If configured for switched then the line will transmit all one bits (mark state). The default value for this parameter is 'constant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER constant(1), switched(2)  

sdlcClocking 1.3.6.1.4.1.485.3.5.3.1.1.5
Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical DTE. X21 External and Internal are used (with the proper external adapter) to support X.21 Leased Line operation for RS-422/RS-530 (25 pin balanced) interfaces. X21 operation is not supported for boards that operate RS-232 or V.35. The default value for this field is 'external'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER external(1), internal(2), x21-external(3), x21-internal(4)  

sdlcSpeed 1.3.6.1.4.1.485.3.5.3.1.1.6
The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-232 ports units (must be V.35 or RS-422).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcPause 1.3.6.1.4.1.485.3.5.3.1.1.7
This parameter defines the amount of time between polls in 1/100 second (10 millisecond) intervals. If set to zero then the port will poll the PUs as fast as possible. The minimum value for this parameter is 5 and the timer has a resolution of 25 milliseconds. The default value is 20 (.20 seconds). This field is not applicable to Host port. It returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcNRZI 1.3.6.1.4.1.485.3.5.3.1.1.8
This parameter indicates whether the port is configured for NRZI (yes) or NRZ (no) bit encoding. The default value is 'No' (NRZ encoding selected).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

sdlcT1Timer 1.3.6.1.4.1.485.3.5.3.1.1.9
The SDLC T1 timer value in 20ths of a second. The default value is 20 (5 seconds). This field is not applicable to Host ports. It returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcSlowPollTimer 1.3.6.1.4.1.485.3.5.3.1.1.10
The slow poll timer value in 20ths of a second. The slow poll timer is the amount of time to wait to contact (send SNRM) failed PUs. The default value for this field is 600 (30 seconds). This field is not applicable to Host ports. It returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcMaxRetries 1.3.6.1.4.1.485.3.5.3.1.1.11
The maximum number of retries (N2 value) before failing a PU. The default value for this field is 3. This field is not applicable to Host ports. It returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

sdlcNAUName 1.3.6.1.4.1.485.3.5.3.1.1.12
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

sdlcMultiFlagInsertion 1.3.6.1.4.1.485.3.5.3.1.1.13
This parameter indicates whether the port is configured to send multiple interframe flags. The default value is 'No' (single flags).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

sdlcStatsTable 1.3.6.1.4.1.485.3.5.3.2
A table of SDLC information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcStatsEntry

sdlcStatsEntry 1.3.6.1.4.1.485.3.5.3.2.1
An entry consisting of port information for a particular SDLC port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SdlcStatsEntry  

sdlcStatsPortIndex 1.3.6.1.4.1.485.3.5.3.2.1.1
The port number that uniquely identifies this SDLC port. Current supported numbers on are 1-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcPortType 1.3.6.1.4.1.485.3.5.3.2.1.2
The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports emulate a line with Terminal Controllers (PUs) and respond to polls from the Host or upstream PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hsdlc-type(11), tsdlc-type(12)  

sdlcInOctets 1.3.6.1.4.1.485.3.5.3.2.1.3
The number of bytes received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcOutOctets 1.3.6.1.4.1.485.3.5.3.2.1.4
The number of bytes sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcInFrames 1.3.6.1.4.1.485.3.5.3.2.1.5
The number of I-frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcOutFrames 1.3.6.1.4.1.485.3.5.3.2.1.6
The number of I-frames sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcOverruns 1.3.6.1.4.1.485.3.5.3.2.1.7
The number of overruns.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcCRCErrors 1.3.6.1.4.1.485.3.5.3.2.1.8
The number of CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcRecvAborts 1.3.6.1.4.1.485.3.5.3.2.1.9
The number of aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncConfigTable 1.3.6.1.4.1.485.3.5.4.1
A table of Bisync port information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BisyncConfigEntry

bisyncConfigEntry 1.3.6.1.4.1.485.3.5.4.1.1
An entry consisting of port information for a particular Bisync port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BisyncConfigEntry  

bisyncConfigPortIndex 1.3.6.1.4.1.485.3.5.4.1.1.1
The port number that uniquely identifies this port. Current supported Bisync numbers are 1-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncConfigType 1.3.6.1.4.1.485.3.5.4.1.1.2
The port type. TBSC (Terminal Bisync) ports emulate a Host and polls the downstream controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal Controllers (CUs) and respond to polls from the Host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hbsc-type(1), tbsc-type(2)  

bisyncNAUName 1.3.6.1.4.1.485.3.5.4.1.1.3
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

bisyncInitState 1.3.6.1.4.1.485.3.5.4.1.1.4
The initial state of the Bisync port. If configured for 'in-service', then the Bisync port will be brougt up automattically when the unit is powered up. If configured for 'out-of-service', then the Bisync port must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'enabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

bisyncCarrier 1.3.6.1.4.1.485.3.5.4.1.1.5
This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked), or Request To Send (a.k.a. RTS, RS-232 pin 4) is constant or switched. The default value for this parameter is 'constant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER constant(1), switched(2)  

bisyncClocking 1.3.6.1.4.1.485.3.5.4.1.1.6
Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical DTE. X21 External and Internal are used (with the proper external adapter) to support X.21 Leased Line operation for RS-422/RS-530 (25 pin balanced) interfaces. X21 operation is not supported for boards that operate RS-232 or V.35. The default value for this field is 'external'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER external(1), internal(2), x21-external(3), x21-internal(4)  

bisyncSpeed 1.3.6.1.4.1.485.3.5.4.1.1.7
The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 64000 are not supported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncPause 1.3.6.1.4.1.485.3.5.4.1.1.8
This parameter defines the amount of time between polls in 1/100 second (10 millisecond) intervals. If set to zero then the port will poll the CUs as fast as possible. The minimum value for this parameter is 5 and the timer has a resolution of 25 milliseconds. The default value is 20 (.20 seconds). This field is not applicable to a Host port. It returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncReplyTimer 1.3.6.1.4.1.485.3.5.4.1.1.9
The time to wait for a response in seconds. The default value for this field is 3 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

bisyncRetries 1.3.6.1.4.1.485.3.5.4.1.1.10
The maximum number of retries (N2 value) before failing a CU. The default value for this field is 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

bisyncSlowpollTimer 1.3.6.1.4.1.485.3.5.4.1.1.11
The time to wait in seconds before attempting a slowpoll. The default value for this field is 30 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..99  

bisyncSessTerm 1.3.6.1.4.1.485.3.5.4.1.1.12
The type of session termination used. Only applies to Host BSC ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), interventionReq(2), unformattedLogoff(3)  

bisyncStatsTable 1.3.6.1.4.1.485.3.5.4.2
A table of Bisync information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BisyncStatsEntry

bisyncStatsEntry 1.3.6.1.4.1.485.3.5.4.2.1
An entry consisting of port information for a particular Bisync port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BisyncStatsEntry  

bisyncStatsPortIndex 1.3.6.1.4.1.485.3.5.4.2.1.1
The port number that uniquely identifies this Bisync port. Current supported numbers are 1-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncPortType 1.3.6.1.4.1.485.3.5.4.2.1.2
The port type. TBSC (Terminal Bisync) ports emulate a Host and poll the downstream controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal Controllers (PUs) and respond to polls from the Host or upstream PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hbsc-type(1), tbsc-type(2)  

bisyncInOctets 1.3.6.1.4.1.485.3.5.4.2.1.3
The number of bytes received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncOutOctets 1.3.6.1.4.1.485.3.5.4.2.1.4
The number of bytes sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncOverruns 1.3.6.1.4.1.485.3.5.4.2.1.5
The number of receiver overruns.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncCRCErrors 1.3.6.1.4.1.485.3.5.4.2.1.6
The number of receive frame CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncRcvTimeout 1.3.6.1.4.1.485.3.5.4.2.1.7
The number of receive timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncXmtTimeout 1.3.6.1.4.1.485.3.5.4.2.1.8
The number of transmit timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frameRelayConfigTable 1.3.6.1.4.1.485.3.5.5.1
A table of Sync product Frame Relay information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrameRelayConfigEntry

frameRelayConfigEntry 1.3.6.1.4.1.485.3.5.5.1.1
An entry consisting of port information for a particular Sync product Frame Relay port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrameRelayConfigEntry  

frameRelayConfigPortIndex 1.3.6.1.4.1.485.3.5.5.1.1.1
The port number that uniquely identifies this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frameRelayPortType 1.3.6.1.4.1.485.3.5.5.1.1.2
The Frame Relay port type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER frame-relay-type(19)  

frameRelayInitState 1.3.6.1.4.1.485.3.5.5.1.1.3
The initial state of the Frame Relay port. If configured for 'in-service', then the Frame Relay port will be brougt up automatically when the unit is powered up. If configured for 'out-of-service', then the Frame Relay port must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'enabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

frameRelayClocking 1.3.6.1.4.1.485.3.5.5.1.1.4
Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical DTE. X21 External and Internal are used (with the proper external adapter) to support X.21 Leased Line operation for RS-422/RS-530 (25 pin balanced) interfaces. X21 operation is not supported for boards that operate RS-232 or V.35. The default value for this field is 'external'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER external(1), internal(2), x21-external(3), x21-internal(4)  

frameRelaySpeed 1.3.6.1.4.1.485.3.5.5.1.1.5
The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-232 port Sync products (must be V.35 or RS-422).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frameRelayLocalManagementProtocol 1.3.6.1.4.1.485.3.5.5.1.1.6
The ports management protocol type. Annex D = ANSI T1.617 Annex D LMI = Frame Relay Manufacturers LMI The default value is Annex D.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER annexD(1), lmi(2)  

frameRelayLinkPollingTimer 1.3.6.1.4.1.485.3.5.5.1.1.7
Measured in seconds, intervals of 5 T391 - Annex D nT1 - LMI The default value for this field is 5 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 5..30  

frameRelayFullStatusPollingCount 1.3.6.1.4.1.485.3.5.5.1.1.8
The number of polls that a full status poll is issued. N391 - Annex D nT1 - LMI The default value for this field is 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

frameRelayT1Timer 1.3.6.1.4.1.485.3.5.5.1.1.9
The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 seconds. The default value for this field is 3 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..25  

frameRelayT2Timer 1.3.6.1.4.1.485.3.5.5.1.1.10
The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be sent for every I frame received. Current supported values are 0 and 2-50. T2 should be less than T1. The default value for this field is 0 (disabled).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..50  

frameRelayTiTimer 1.3.6.1.4.1.485.3.5.5.1.1.11
The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 seconds. The default value for this field is 30 seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..50  

frameRelayRxWindowSize 1.3.6.1.4.1.485.3.5.5.1.1.12
The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3 which is the number of I frames received before an RR frame is sent (defined as N3 in IEEE 802.2 LLC). Current allowable values are 1-7. The default value for this field is 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7  

frameRelayTxWindowSize 1.3.6.1.4.1.485.3.5.5.1.1.13
The defalut LLC transmit window size. Current allowable values are 1-7. The default value for this field is 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7  

frameRelayMaxRetries 1.3.6.1.4.1.485.3.5.5.1.1.14
The default LLC maximum number of retries (N2 value). The default value for this field is 15.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..20  

frameRelayNAUName 1.3.6.1.4.1.485.3.5.5.1.1.15
The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

frameRelayVirtualMACAddress 1.3.6.1.4.1.485.3.5.5.1.1.16
The F/R WAN is treated as a token ring. This address is used for communication with other bridges in the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

frameRelayVirtualRingNumber 1.3.6.1.4.1.485.3.5.5.1.1.17
The F/R WAN is treated as a token ring. This is the ring number for the F/R network to which the port is attached. It must be a unique ring number in the network. The default value for this field is 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

frameRelayVirtualBridgeNumber 1.3.6.1.4.1.485.3.5.5.1.1.18
The F/R WAN is treated as a token ring. This variable only has significance if more than 1 F/R port is configured. The default value for this field is 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..15  

frameRelayIPAddress 1.3.6.1.4.1.485.3.5.5.1.1.19
This is the IP Address of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

frameRelayNetworkMask 1.3.6.1.4.1.485.3.5.5.1.1.20
This is the network mask to be used on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

frameRelayDefaultGatewayAddress 1.3.6.1.4.1.485.3.5.5.1.1.21
Default gateway address to be used when sending responses on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

frameRelayStatsTable 1.3.6.1.4.1.485.3.5.5.2
A table of Frame Relay information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrameRelayStatsEntry

frameRelayStatsEntry 1.3.6.1.4.1.485.3.5.5.2.1
An entry consisting of port information for a particular Frame Relay port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrameRelayStatsEntry  

frameRelayStatsPortIndex 1.3.6.1.4.1.485.3.5.5.2.1.1
The port number that uniquely identifies this Frame Relay port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frameRelayInOctets 1.3.6.1.4.1.485.3.5.5.2.1.2
The number of bytes received inclusive of all valid bytes in the frame relay frame except for the CRC field (frame relay header included).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frameRelayOutOctets 1.3.6.1.4.1.485.3.5.5.2.1.3
The number of bytes transmitted inclusive of all bytes in the frame relay frame except for the CRC field (frame relay header included).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frameRelaySampleDuration 1.3.6.1.4.1.485.3.5.5.2.1.4
The sample duration in seconds for Frame Relay Statistics for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frameRelayOverruns 1.3.6.1.4.1.485.3.5.5.2.1.5
The number of receiver overruns.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frameRelayCRCErrors 1.3.6.1.4.1.485.3.5.5.2.1.6
The number of received CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

frameRelayRecvAborts 1.3.6.1.4.1.485.3.5.5.2.1.7
The number of received frame aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

puControlTable 1.3.6.1.4.1.485.3.6.1.1
A table for controlling lines and obtaining information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PuControlEntry

puControlEntry 1.3.6.1.4.1.485.3.6.1.1.1
An entry consisting of PU information for a particular port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PuControlEntry  

puControlLineIndex 1.3.6.1.4.1.485.3.6.1.1.1.1
The port number that has a given PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

puControlPUAddress 1.3.6.1.4.1.485.3.6.1.1.1.2
The PU address in the range of 0x01 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

puStatus 1.3.6.1.4.1.485.3.6.1.1.1.3
The status of the PU. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. Commands: An enable command will attempt to bring up the PU. An enable all command will attempt to bring up the line and any lower layer entities (e.g. PUs). A disable command will disable the PU. Status: Enable(d) indicates the PU is enabled and running. Disable(d) indicates the PU has been disabled. Failed indicates the PU is enabled and not Running.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), failed(3), restart(4), enable-all(5)  

puConnectionStatus 1.3.6.1.4.1.485.3.6.1.1.1.4
The status of the LLC type 2 Connection for this SDLC PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), not-connected(2)  

puLastClearCode 1.3.6.1.4.1.485.3.6.1.1.1.5
A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed connection attempt (a.k.a. call attempt) or active connection (a.k.a. session). For LLC type 2 connections the first octet (cause) is always 0. The second octet (diagnostic) indicates the reason for the last connection failure. The second octet is set to 0 when a sucessful call has been placed, or if no call has ever been placed (e.g. PU never came up). If the second octet is non-zero then it indicates the reason for the connection attempt failure. See User's Guide for information
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

puControlFailureCode 1.3.6.1.4.1.485.3.6.1.1.1.6
This entry contains the failure codes if the associated PU is in the failed state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

puControlNAUName 1.3.6.1.4.1.485.3.6.1.1.1.7
The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

puConnectionAttemptCount 1.3.6.1.4.1.485.3.6.1.1.1.8
The number of connection attempts performed. This count is set to zero at startup, and after every loss of an estabished session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuConfigTable 1.3.6.1.4.1.485.3.6.2.1
A list of PU entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcPuConfigEntry

sdlcPuConfigEntry 1.3.6.1.4.1.485.3.6.2.1.1
This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SdlcPuConfigEntry  

sdlcPuConfigLineIndex 1.3.6.1.4.1.485.3.6.2.1.1.1
The port number for which the line (CU)is configured (first level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcPuConfigAddress 1.3.6.1.4.1.485.3.6.2.1.1.2
The PU address in the range of 0x00 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

sdlcPuNAUName 1.3.6.1.4.1.485.3.6.2.1.1.3
The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

sdlcPuInitialState 1.3.6.1.4.1.485.3.6.2.1.1.4
The initial state of the PU. If configured for 'in-service', then the SDLC PU will be brougt up automattically when the unit is powered up. If configured for 'out-of-service', the the SDLC PU must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'in-service'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

sdlcPuXID 1.3.6.1.4.1.485.3.6.2.1.1.5
The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. If the field is configured to 0 then the unit will solicit the XID from the downstream PU and send the XID data received from SDLC to the XID data sent for the LLC connection process. If not sent to 0, then the unit will insert the data configured in the LLC sent to the host during the LLC connection process on behalf of the CU. For incoming LLC connections on Sync Research products this field is parsed to route the connection to the proper PU. The default value for this field is all zeroes (solicit XID from PU).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

sdlcPuType 1.3.6.1.4.1.485.3.6.2.1.1.6
The SNA PU type. 1 = PU type 1 2 = PU type 2 3 = PU type 2.1 4 = PU type 4 (not supported, reserved) 5 = PU type 5 (not supported, reserved) This parameter defaults to a value of 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER type1(1), type2(2), type2-1(3), type4(4), type5(5)  

sdlcPuGroupPollAddress 1.3.6.1.4.1.485.3.6.2.1.1.7
The PU's group address in the range of 0x01 to 0xfe. setting this value to 0 will disable the group poll feature for polling this and other PUs in a group. The default value for this field is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

sdlcPuConnectionID 1.3.6.1.4.1.485.3.6.2.1.1.8
This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

sdlcPuMAXOUT 1.3.6.1.4.1.485.3.6.2.1.1.9
This entry defines the maximum number of outstanding I frames that the PU will allow. This field is applicable to TSDLC only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcPuConnectType 1.3.6.1.4.1.485.3.6.2.1.1.10
The SNA PU Connection type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

sdlcPuStatsTable 1.3.6.1.4.1.485.3.6.2.2
A list of PU statistics entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcPuStatsEntry

sdlcPuStatsEntry 1.3.6.1.4.1.485.3.6.2.2.1
This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SdlcPuStatsEntry  

sdlcPuStatsLineIndex 1.3.6.1.4.1.485.3.6.2.2.1.1
The port number for which PU is configured on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sdlcPuStatsAddress 1.3.6.1.4.1.485.3.6.2.2.1.2
The PU address in the range of 0x00 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

sdlcPuInIFrames 1.3.6.1.4.1.485.3.6.2.2.1.3
The number of I frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutIFrames 1.3.6.1.4.1.485.3.6.2.2.1.4
The number of I frames trasnmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInRRFrames 1.3.6.1.4.1.485.3.6.2.2.1.5
The number of RR frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutRRFrames 1.3.6.1.4.1.485.3.6.2.2.1.6
The number of RR frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInRNRFrames 1.3.6.1.4.1.485.3.6.2.2.1.7
The number of RNR frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutRNRFrames 1.3.6.1.4.1.485.3.6.2.2.1.8
The number of RNR frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInXIDFrames 1.3.6.1.4.1.485.3.6.2.2.1.9
The number of XID frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutXIDFrames 1.3.6.1.4.1.485.3.6.2.2.1.10
The number of XID frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInTESTFrames 1.3.6.1.4.1.485.3.6.2.2.1.11
The number of TEST frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutTESTFrames 1.3.6.1.4.1.485.3.6.2.2.1.12
The number of TEST frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInSNRMFrames 1.3.6.1.4.1.485.3.6.2.2.1.13
The number of SNRM frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutSNRMFrames 1.3.6.1.4.1.485.3.6.2.2.1.14
The number of SNRM frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInDISCFrames 1.3.6.1.4.1.485.3.6.2.2.1.15
The number of DISC frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutDISCFrames 1.3.6.1.4.1.485.3.6.2.2.1.16
The number of DISC frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInDMFrames 1.3.6.1.4.1.485.3.6.2.2.1.17
The number of DM frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutDMFrames 1.3.6.1.4.1.485.3.6.2.2.1.18
The number of DM frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInUAFrames 1.3.6.1.4.1.485.3.6.2.2.1.19
The number of UA frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutUAFrames 1.3.6.1.4.1.485.3.6.2.2.1.20
The number of UA frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInFRMRFrames 1.3.6.1.4.1.485.3.6.2.2.1.21
The number of FRMR frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutFRMRFrames 1.3.6.1.4.1.485.3.6.2.2.1.22
The number of FRMR frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInRDFrames 1.3.6.1.4.1.485.3.6.2.2.1.23
The number of RD frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutRDFrames 1.3.6.1.4.1.485.3.6.2.2.1.24
The number of RD frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuInUIFrames 1.3.6.1.4.1.485.3.6.2.2.1.25
The number of UI frames received on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuOutUIFrames 1.3.6.1.4.1.485.3.6.2.2.1.26
The number of UI frames transmitted on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuReTxIFrames 1.3.6.1.4.1.485.3.6.2.2.1.27
The number of re-transmitted I frames on this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sdlcPuPollResponseTimeouts 1.3.6.1.4.1.485.3.6.2.2.1.28
The number of PU Poll Response timeouts for this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncPuConfigTable 1.3.6.1.4.1.485.3.6.3.1
A list of Bisync CU entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BisyncPuConfigEntry

bisyncPuConfigEntry 1.3.6.1.4.1.485.3.6.3.1.1
This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BisyncPuConfigEntry  

bisyncPuConfigLineIndex 1.3.6.1.4.1.485.3.6.3.1.1.1
The port number for which PU is configured on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncPuConfigAddress 1.3.6.1.4.1.485.3.6.3.1.1.2
The PU address in the range of 0x00 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

bisyncPuNAUName 1.3.6.1.4.1.485.3.6.3.1.1.3
The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

bisyncPuInitialState 1.3.6.1.4.1.485.3.6.3.1.1.4
The initial state of the PU. If configured for 'in-service', then the SDLC PU will be brougt up automattically when the unit is powered up. If configured for 'out-of-service', the the SDLC PU must be manually enabled by operator intervention (i.e. enable command must be sent). The default value is 'in-service'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-service(1), out-of-service(2)  

bisyncPuXID 1.3.6.1.4.1.485.3.6.3.1.1.5
The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. The unit will insert the data configured in the LLC XID sent to the host during the LLC connection process on behalf of the CU. For bisync control units, this field is required as bisync cannot solicit an XID. For incoming LLC connections on Sync Research products this field is parsed to route the connection to the proper PU. The default value for this field is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

bisyncPuTargetHostType 1.3.6.1.4.1.485.3.6.3.1.1.6
The Target Host type. 1 = SNA host type 2 = Bisync host type This field specifies the target host type for TBSC and is applicable to BSC-to-SNA conversion only. This parameter defaults to a value of 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sna-host-type(1), bisync-host-type(2)  

bisyncPuMaxData 1.3.6.1.4.1.485.3.6.3.1.1.7
This entry defines the SNA frame size which is the sum of SNA data and SNA header. This value must match the MAXData configured for SNA host and is applicable to BSC-to-SNA conversion only. The default value is 521. The valid range is 265, 521, 777, 1033, 1289.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncPuConnectionID 1.3.6.1.4.1.485.3.6.3.1.1.8
This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

bisyncPuConnectType 1.3.6.1.4.1.485.3.6.3.1.1.9
The Bisync PU Connection type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER answer(1), originate(2)  

bisyncPuStatsTable 1.3.6.1.4.1.485.3.6.3.2
A list of PU statistics entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BisyncPuStatsEntry

bisyncPuStatsEntry 1.3.6.1.4.1.485.3.6.3.2.1
This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BisyncPuStatsEntry  

bisyncPuStatsLineIndex 1.3.6.1.4.1.485.3.6.3.2.1.1
The port number for which PU is configured on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bisyncPuStatsAddress 1.3.6.1.4.1.485.3.6.3.2.1.2
The PU address in the range of 0x00 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

bisyncPuInTransactions 1.3.6.1.4.1.485.3.6.3.2.1.3
The number of PU Poll Response timeouts for this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncPuOutTransactions 1.3.6.1.4.1.485.3.6.3.2.1.4
The number of PU Poll Response timeouts for this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncPuSlowPolls 1.3.6.1.4.1.485.3.6.3.2.1.5
The number of PU slow polls for this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bisyncPuPolls 1.3.6.1.4.1.485.3.6.3.2.1.6
The number of PU Polls for this PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mappingPuConfigTable 1.3.6.1.4.1.485.3.6.4.1
A list of PU mapping entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MappingPuConfigEntry

mappingPuConfigEntry 1.3.6.1.4.1.485.3.6.4.1.1
This entry contains information about a given mapping PU. Each entry includes MAC/SAP information for a source PU and a similar information for the partner (mapped) PU. Depending upon whether the PU is LAN-attached, SDLC-attached or Frame Relay-attached, one or more fields may not apply. Some fields, for example, mappingPuNAU, mappingPuXID, mappingPuConnectID are common to both end points. The entry is indexed by the port number and the PU number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MappingPuConfigEntry  

mappingPuConfigLineIndex 1.3.6.1.4.1.485.3.6.4.1.1.1
The port number for which PU is associated with. Port number 99 is a special value which is used to indicate NetView PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mappingPuConfigAddress 1.3.6.1.4.1.485.3.6.4.1.1.2
The PU address in the range of 0x01 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuSourceSAP 1.3.6.1.4.1.485.3.6.4.1.1.3
The LLC source SAP value for this PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync products are configured to always call the same remote Token-Ring Host or Gateway for all connections configured. This means that all the Destination SAP (usually set to 4) and Destination MAC addresses are the same, so the Source SAP field must be set to a unique value in order to uniquely identify the LLC connection to the Host. (SNA does not allow multiplexing of PUs on one LLC connection. Each PU must have its own LLC Type 2 connection.) This field must be set to a range between 04 and E8 hexadecimal and it must be evenly divisible by 4 (802.2 LLC rules for user assigned SAPs). This field is not applicable in all cases, if not it returns a dummy value. This parameter defaults to a value of 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuDestinationSAP 1.3.6.1.4.1.485.3.6.4.1.1.4
The LLC Destination SAP value for this PU. For SNA typically the destination is almost always SAP 4. However both Host Front Ends (e.g. 3745) or Gateways (e.g. 3174) allow SAPs to be configured for any value betwee 0x04 and 0xEC as long as the SAP ID is a user assignable individual SAP ID (any value evenly divisable by 4). This field is not applicable to all cases. If not it returns a dummy value. This parameter defaults to a value of 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuDestinationMAC 1.3.6.1.4.1.485.3.6.4.1.1.5
The LAN Destination MAC address used in the LLC Type 2 connection for this PU. The Token-Ring format for this field is a 6 octet (48 bit) field represented in IEEE 802.5 format where the first bit transmitted is the most significant bit. The destination MAC must also be an 'Individual' address. Therefore valid addresses are between 000000000001 and 7FFFFFFFFFFF (an address of all zeroes is not supported). The Ethernet format for this field is a 6 octet (48 bit) field represented in IEEE 802.3 format where the first bit transmitted is the least significant bit. The destination MAC must also be an 'Individual' address. Therefore valid addresses must start with the least significant bit equal to 0. In other words, the first two digits must be in the set of 0x00, 0x02, 0x04, ... 0xFE (an address of all 12 digits equal to zeroes is not supported). This field is not applicable to all cases. If not it returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

mappingPuPartnerConfigLineIndex 1.3.6.1.4.1.485.3.6.4.1.1.6
The port number for the partner PU associated with source PU. Port number 99 is a special value which is used to indicate NetView PU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mappingPuPartnerConfigAddress 1.3.6.1.4.1.485.3.6.4.1.1.7
The PU address of the partner PU in the range of 0x01 to 0xfe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuPartnerSourceSAP 1.3.6.1.4.1.485.3.6.4.1.1.8
The LLC source SAP value for a partner PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync products are configured to always call the same remote Token-Ring Host or Gateway for all connections configured. This means that all the Destination SAP (usually set to 4) and Destination MAC addresses are the same, so the Source SAP field must be set to a unique value in order to uniquely identify the LLC connection to the Host. (SNA does not allow multiplexing of PUs on one LLC connection. Each PU must have its own LLC Type 2 connection.) This field must be set to a range between 04 and E8 hexadecimal and it must be evenly divisible by 4 (802.2 LLC rules for user assigned SAPs). This field is not applicable in all cases, if not it returns a dummy value. This parameter defaults to a value of 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuPartnerDestSAP 1.3.6.1.4.1.485.3.6.4.1.1.9
The LLC Destination SAP value for the partner PU. For SNA typically the destination is almost always SAP 4. However both Host Front Ends (e.g. 3745) or Gateways (e.g. 3174) allow SAPs to be configured for any value betwee 0x04 and 0xEC as long as the SAP ID is a user assignable individual SAP ID (any value evenly divisable by 4). This field is not applicable to all cases. It returns a dummy value. This parameter defaults to a value of 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mappingPuPartnerDestMAC 1.3.6.1.4.1.485.3.6.4.1.1.10
The LAN Destination MAC address used in the LLC Type 2 connection for the partner PU. The Token-Ring format for this field is a 6 octet (48 bit) field represented in IEEE 802.5 format where the first bit transmitted is the most significant bit. The destination MAC must also be an 'Individual' address. Therefore valid addresses are between 000000000001 and 7FFFFFFFFFFF (an address of all zeroes is not supported). The Ethernet format for this field is a 6 octet (48 bit) field represented in IEEE 802.3 format where the first bit transmitted is the least significant bit. The destination MAC must also be an 'Individual' address. Therefore valid addresses must start with the least significant bit equal to 0. In other words, the first two digits must be in the set of 0x00, 0x02, 0x04, ... 0xFE (an address of all 12 digits equal to zeroes is not supported). This field is not applicable to all cases. If not it returns a dummy value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

mappingPuNAU 1.3.6.1.4.1.485.3.6.4.1.1.11
The NAU Name. The NAU name is same for both the source PU and the partner PU. It represents one physical PU in a network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

mappingPuConnectID 1.3.6.1.4.1.485.3.6.4.1.1.12
The connection ID. This must match a connection ID of an access line PU or another mapping PU Connection ID. The connnection ID is 0 if there is no mapping.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mappingPuXID 1.3.6.1.4.1.485.3.6.4.1.1.13
The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. For incoming LLC connections on Sync Research products this field is parsed to route the connection to the proper PU. The XID is same for both the source PU and the partner PU. It represents one physical PU in a network. The default value for this field is all zeroes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

mappingPuDirectDLCI 1.3.6.1.4.1.485.3.6.4.1.1.14
The Frame Relay DLCI used in the LLC Type 2 connection for this PU. The Frame Relay format for this field is a 2 octet (16 bit) field represented in BCD format. A valid DLCI would be from 0001 to 1023 (0000 is reserved for AnnexD management. 1023 is reserved for LMI mangement.). This value is applicable to Frame Relay-attached PU only. The field corresponds to a source port or a partner port depending upon whether the source PU is a Frame Relay-attached PU or the partner PU is Frame Relay-attached PU. For Frame Relay-attached PU if this value is not configured, 0 is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

deviceControlTable 1.3.6.1.4.1.485.3.7.1.1
A table for controlling devices and obtaining information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceControlEntry

deviceControlEntry 1.3.6.1.4.1.485.3.7.1.1.1
An entry consisting of device information for a particular device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DeviceControlEntry  

deviceControlIndex 1.3.6.1.4.1.485.3.7.1.1.1.1
The number that uniquely identifies this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceControlCUIndex 1.3.6.1.4.1.485.3.7.1.1.1.2
The CU index for this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceControlAddress 1.3.6.1.4.1.485.3.7.1.1.1.3
The device address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

deviceStatus 1.3.6.1.4.1.485.3.7.1.1.1.4
The status of the device. To change (write) status of a device, enable, disable, restart or enable all may be set. Valid Return (read) status are enable(d), disable(d), or failed (d). Commands: An enable command will attempt to bring up the device. An enable all command will perform the same function as enable, since there are no sub elements on a device. A disable command will disable the device. Status: Enable(d) indicates the device is enabled and running. Disable(d) indicates the device has been disabled. Failed (d) indicates the device is enabled and not Running.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), failed(3), restart(4), enable-all(5)  

deviceControlFailureCode 1.3.6.1.4.1.485.3.7.1.1.1.5
This entry contains the failure codes if the associated device is in the failed state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

deviceConfigTable 1.3.6.1.4.1.485.3.7.2.1
A list of device entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceConfigEntry

deviceConfigEntry 1.3.6.1.4.1.485.3.7.2.1.1
This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DeviceConfigEntry  

deviceConfigLineIndex 1.3.6.1.4.1.485.3.7.2.1.1.1
The port number for which the line (CU)is configured (line level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceConfigCUIndex 1.3.6.1.4.1.485.3.7.2.1.1.2
The CU index which this device is configured on (CU level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceConfigAddress 1.3.6.1.4.1.485.3.7.2.1.1.3
The device address in the legal range of BSC poll addresses (device level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

deviceConfigType 1.3.6.1.4.1.485.3.7.2.1.1.4
The device type. The default value is crt.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER crt(1), printer(2)  

deviceStatsTable 1.3.6.1.4.1.485.3.7.2.2
A table of device statistics information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceStatsEntry

deviceStatsEntry 1.3.6.1.4.1.485.3.7.2.2.1
This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DeviceStatsEntry  

bscDeviceLineIndex 1.3.6.1.4.1.485.3.7.2.2.1.1
The port number for which the line (CU)is configured (line level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bscDeviceCUIndex 1.3.6.1.4.1.485.3.7.2.2.1.2
The CU index which this device is configured on (CU level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

bscDeviceAddress 1.3.6.1.4.1.485.3.7.2.2.1.3
The device address in the legal range of BSC poll addresses (device level).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

bscDeviceInTransactions 1.3.6.1.4.1.485.3.7.2.2.1.4
The number of device receiving transactions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bscDeviceOutTransactions 1.3.6.1.4.1.485.3.7.2.2.1.5
The number of device transmitting transactions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bscDeviceSumCount 1.3.6.1.4.1.485.3.7.2.2.1.6
The device sum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bscDeviceResponseDelaySum 1.3.6.1.4.1.485.3.7.2.2.1.7
The device sum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

bscDeviceResponseDelaySqSum 1.3.6.1.4.1.485.3.7.2.2.1.8
The device sum count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

configChanged 800
This trap indicates that the configuration of the unit has been changed.
TRAP-TYPE    

configError 801
This trap indicates that the activation of configuration of the unit has resulted in an error. New configuration has not been successfully activated.
TRAP-TYPE    

dumpExists 802
This trap indicates that a memory core dump exists.
TRAP-TYPE    

dumpArchived 803
This trap indicates that the memory dump file has been archived.
TRAP-TYPE    

lineStatusChanged 804
This trap indicates that the indicated Line or Port has changed state. It has either been enabled, failed or disabled.
TRAP-TYPE    

lanStatusChanged 805
This trap indicates that the indicated LAN Port has changed state. It has either been enabled, failed or disabled.
TRAP-TYPE    

lineQuality 806
TRAP-TYPE    

puStatusChanged 807
This trap indicates that the indicated PU has changed state. It has either been enabled, failed or disabled.
TRAP-TYPE    

puConnectionStatusChanged 808
Note this trap is obsolete. This trap indicates that the indicated PU has changed connection state. Its connection has either been established, disconnected, or rejected.
TRAP-TYPE    

netviewConnectionStatusChanged 809
Note this trap is obsolete. This trap indicates that the NetView PU has changed connection state. Its connection has either been established, disconnected, or rejected.
TRAP-TYPE    

netviewAltConnectionStatusChanged 810
Note this trap is obsolete. This trap indicates that the Alternate NetView PU has changed connection state. Its connection has either been established, disconnected, or rejected.
TRAP-TYPE    

puConnectionStatusUp 811
This trap indicates that the indicated PU has changed connection state. Its connection had been established.
TRAP-TYPE    

puConnectionStatusDown 812
This trap indicates that the indicated PU has changed connection state. Its connection has been disconnected. If the indicated PU is not in session, the trap is generated only if the clear code is different from the puLastClearCode.
TRAP-TYPE    

netviewConnectionStatusUp 813
This trap indicates that the indicated NetView PU has changed connection state. Its connection has been established.
TRAP-TYPE    

netviewConnectionStatusDown 814
This trap indicates that the indicated NetView PU has changed connection state. Its connection had been disconnected. If the indicated PU is not in session, the trap is generated only if the clear code is different from the netviewLastClearCode.
TRAP-TYPE    

netviewAltConnectionStatusUp 815
This trap indicates that the indicated Alternate NetView PU has changed connection state. Its connection has been established.
TRAP-TYPE    

netviewAltConnectionStatusDown 816
This trap indicates that the indicated Alternate NetView PU has changed connection state. Its connection had been disconnected. If the indicated PU is not in session, the trap is generated only if the clear code is different from the netviewAltLastClearCode.
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor