TIMETRA-ETH-RING-MIB

File: TIMETRA-ETH-RING-MIB.mib (41939 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
TIMETRA-GLOBAL-MIB IF-MIB TIMETRA-SERV-MIB
TIMETRA-SAP-MIB TIMETRA-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TEXTUAL-CONVENTION RowStatus
TimeStamp TruthValue MacAddress
timetraSRMIBModules tmnxSRObjs tmnxSRNotifyPrefix
tmnxSRConfs InterfaceIndexOrZero svcId
sapPortId sapEncapValue TmnxAdminState
TmnxOperState TmnxEncapVal TItemDescription

Defined Types

TmnxEthRingIndex  
The TmnxEthRingIndex specifies the unique Ethernet Ring Identifier for an Ethernet Ring Node. The value of zero (0) is only used by objects which may reference a tmnxEthRingConfigEntry. The value zero (0) is an invalid index that specifies that the object is not associated with any Ethernet Ring Node.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxEthRingPathIndex  
The TmnxEthRingPathIndex specifies the unique Ethernet Ring Path Identifier. Along with an Object of type TmnxEthRingIndex, an Object of this type references a specific path on a specific Ethernet Ring Node.
TEXTUAL-CONVENTION    
  INTEGER pathA(0), pathB(1)  

TmnxEthRingRplNodeType  
The TmnxEthRingRplNodeType specifies the Ring Protection Link (RPL) Node type. An object of this type may be assigned to a value of: - rplNone (0) -- The Ethernet Ring Node is not designated as either an Owner or Neighbor Node. - rplOwner(1) -- The Ethernet Ring Node is adjacent to the RPL that is responsible for blocking its end of the RPL under normal conditions. It is the responsibility of the rplOwner for activating reversion behaviour from protected or MS/FS conditions. - rplNeighbor(2) -- The Ethernet Ring Node is adjacent to the RPL that is responsible for blocking its end of the RPL under normal conditions in addition to the block by the RPL Owner Node. The node is, however, not responsibel for activating the reversion behavior.
TEXTUAL-CONVENTION    
  INTEGER rplNone(0), rplOwner(1), rplNeighbor(2)  

TmnxEthRingApsInfoType  
The TmnxEthRingApsInfoType specifies the Ring APS specific PDU message information. If the value of an object of this type is the empty string, then no Ring APS specific PDU message is available. The APS pdu uses the following format: +-------+-------+---------------+---------------+---------------+ |8 7 6 5|4 3 2 1|8 7 6 5 4 3 2 1|8 7 6 ... 3 2 1|8 7 6 ... 3 2 1| |-------+-------+---------------+---------------+---------------+ | Rqst/ | sub- | Status | Node ID | Reserved | | State | code +-+-+-+---------+ (6 octets) | (24 octets) | | | |R|D|B| status | | | | | |B|N|P| Rsvd | | | | | | |F|R| | | | +-------+-------+-+-+-+---------+---------------+---------------+
TEXTUAL-CONVENTION    
  OCTET STRING Size(0|8..32)  

TmnxEthRingConfigEntry  
SEQUENCE    
  tmnxEthRingIndex TmnxEthRingIndex
  tmnxEthRingRowStatus RowStatus
  tmnxEthRingTimeStamp TimeStamp
  tmnxEthRingDescription TItemDescription
  tmnxEthRingAdminState TmnxAdminState
  tmnxEthRingOperState TmnxOperState
  tmnxEthRingGuardTime Unsigned32
  tmnxEthRingRevertTime Unsigned32
  tmnxEthRingRevertTimeCountDn Unsigned32
  tmnxEthRingCcmHoldDownTime Unsigned32
  tmnxEthRingCcmHoldUpTime Unsigned32
  tmnxEthRingRplNode TmnxEthRingRplNodeType
  tmnxEthRingNodeId MacAddress
  tmnxEthRingTxApsPdu TmnxEthRingApsInfoType
  tmnxEthRingDefectStatus BITS
  tmnxEthRingSubRingType INTEGER
  tmnxEthRingSubRingInterconnectId Unsigned32
  tmnxEthRingSubRingPropTopChange TruthValue
  tmnxEthRingCompatibleVersion INTEGER

TmnxEthRingPathEntry  
SEQUENCE    
  tmnxEthRingPathIndex TmnxEthRingPathIndex
  tmnxEthRingPathRowStatus RowStatus
  tmnxEthRingPathTimeStamp TimeStamp
  tmnxEthRingPathIfIndex InterfaceIndexOrZero
  tmnxEthRingPathIfRapsCcTag TmnxEncapVal
  tmnxEthRingPathDescription TItemDescription
  tmnxEthRingPathAdminStatus TmnxAdminState
  tmnxEthRingPathOperStatus TmnxOperState
  tmnxEthRingPathType INTEGER
  tmnxEthRingPathFwdState INTEGER
  tmnxEthRingPathFwdStateChgTime TimeStamp
  tmnxEthRingPathRxApsPdu TmnxEthRingApsInfoType

TmnxEthRingSAPPathEntry  
SEQUENCE    
  tmnxEthRingSAPPathIndex Unsigned32
  tmnxEthRingSAPPathControlFlag TruthValue

TmnxEthRingCommandEntry  
SEQUENCE    
  tmnxEthRingCommandSwitch INTEGER

Defined Values

timetraEthRingMIBModule 1.3.6.1.4.1.6527.1.1.3.72
This document is the SNMP MIB module to manage and provision the Ethernet Ring components of the Alcatel-Lucent SROS device. Copyright (c) 2009-2011 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxEthRingObjs 1.3.6.1.4.1.6527.3.1.2.72
OBJECT IDENTIFIER    

tmnxEthRingNotifyPrefix 1.3.6.1.4.1.6527.3.1.3.72
OBJECT IDENTIFIER    

tmnxEthRingConformance 1.3.6.1.4.1.6527.3.1.1.72
OBJECT IDENTIFIER    

tmnxEthRingConfigTimeStamps 1.3.6.1.4.1.6527.3.1.2.72.0
OBJECT IDENTIFIER    

tmnxEthRingConfigurations 1.3.6.1.4.1.6527.3.1.2.72.1
OBJECT IDENTIFIER    

tmnxEthRingStatistics 1.3.6.1.4.1.6527.3.1.2.72.2
OBJECT IDENTIFIER    

tmnxEthRingNotifications 1.3.6.1.4.1.6527.3.1.3.72.0
OBJECT IDENTIFIER    

tmnxEthRingCompliances 1.3.6.1.4.1.6527.3.1.1.72.1
OBJECT IDENTIFIER    

tmnxEthRingGroups 1.3.6.1.4.1.6527.3.1.1.72.2
OBJECT IDENTIFIER    

tmnxEthRingCfgTblLastChanged 1.3.6.1.4.1.6527.3.1.2.72.0.1
The tmnxEthRingCfgTblLastChanged indicates the time, since system startup, when a row in the tmnxEthRingConfigTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingConfigTable 1.3.6.1.4.1.6527.3.1.2.72.1.1
The tmnxEthRingConfigTable consists of the Ethernet Ring configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthRingConfigEntry

tmnxEthRingConfigEntry 1.3.6.1.4.1.6527.3.1.2.72.1.1.1
The tmnxEthRingConfigEntry contains information pertaining to an individual Ethernet Ring. Rows in this table are created and destroyed using the tmnxEthRingRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingConfigEntry  

tmnxEthRingIndex 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.1
The value of tmnxEthRingIndex specifies the row index of the Ethernet Ring Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingIndex 1..4294967294  

tmnxEthRingRowStatus 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.2
The value of tmnxEthRingRowStatus controls the creation and deletion of row entries in the tmnxEthRingConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxEthRingTimeStamp 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.3
The value of tmnxEthRingTimeStamp indicates the time, since system startup, of the last change to this row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingDescription 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.4
The value of tmnxEthRingDescription specifies the user supplied description of the Ethernet Ring.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxEthRingAdminState 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.5
The value of tmnxEthRingAdminState specifies the administrative state of the Ethernet Ring.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxEthRingOperState 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.6
The value of tmnxEthRingOperState indicates the operational state of the Ethernet Ring.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxEthRingGuardTime 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.7
The value of tmnxEthRingGuardTime specifies the guard timer, in deciseconds, of a Ring-APS (R-APS) node. The guard timer is used to prevent the Ethernet Ring node from acting upon outdated R-APS messages and prevent the possibility of forming a closed loop. While the guard timer is running, any received R-APS Request/State and Status information is blocked and not forwarded to the Priority Logic. When the guard timer is not running, the R-APS Request/State and Status information is forwarded unchanged.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..20  

tmnxEthRingRevertTime 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.8
The value of tmnxEthRingRevertTime specifies the Wait-To-Restore (WTR) timer, in seconds, of a Ring-APS (R-APS) node. The WTR timer is used to prevent frequent operation of the protection switching due to intermittent signal failure defects. Setting tmnxEthRingRevertTime to the value zero (0) puts the Ethernet Ring into a non-revertive mode.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 60..720  

tmnxEthRingRevertTimeCountDn 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.9
The value of tmnxEthRingRevertTimeCountDn indicates the remaining time, in seconds, before the Ethernet Ring can revert to its original state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxEthRingCcmHoldDownTime 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.10
The value of tmnxEthRingCcmHoldDownTime specifies the time, in centiseconds, used for the hold-timer for associated Continuity Check (CC) Session down event dampening. This guards against reporting excessive path operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Ring Node until the configured timer has expired. A value of zero (0) specifies that a down transition is reported immediately.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..5000  

tmnxEthRingCcmHoldUpTime 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.11
The value of tmnxEthRingCcmHoldUpTime specifies the time, in deciseconds, used for the hold-timer for associated Continuity Check (CC) Session up event dampening. This guards against reporting excessive path operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Ring Node until the configured timer has expired. A value of zero (0) specifies that an up transition is reported immediately.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..5000  

tmnxEthRingRplNode 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.12
The value of tmnxEthRingRplNode specifies the Ring Protection Link (RPL) type of the Ethernet Ring Node.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEthRingRplNodeType  

tmnxEthRingNodeId 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.13
The value of tmnxEthRingNodeId specifies the Ethernet Ring Node ID. The default value is the system's MAC address. Writing the MAC address value 00:00:00:00:00:00 to tmnxEthRingNodeId will reset its value to the system's MAC address.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

tmnxEthRingTxApsPdu 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.14
The value of tmnxEthRingTxApsPdu indicates the contents of the R-APS PDU transmitted on the Ethernet Ring.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxEthRingApsInfoType  

tmnxEthRingDefectStatus 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.15
The value of tmnxEthRingDefectStatus indicates what defects are active on the Ethernet Ring. The defects are defined as: dFopPM -- Provisioning Mismatch
Status: current Access: read-only
OBJECT-TYPE    
  BITS dFopPM(0)  

tmnxEthRingSubRingType 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.16
The value of tmnxEthRingSubRingType specifies whether this Ethernet Ring is a sub-ring or not. A value of 'none (0)' specifies that the Ethernet Ring is not a sub-ring. A value 'virtualLink (1)' specifies that the Ethernet Ring is a sub-ring with R-APS virtual channel, while the value 'nonVirtualLink (2)' specifies that the Ethernet Ring is a sub-ring without R-APS virtual channel. This object MUST be set to a value other than 'none (0)' for tmnxEthRingSubRingInterconnectId and tmnxEthRingSubRingPropTopChange to be modified away from their default values.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), virtualLink(1), nonVirtualLink(2)  

tmnxEthRingSubRingInterconnectId 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.17
The value of tmnxEthRingSubRingInterconnectId specifies whether the Ethernet sub-ring is interconnected to an Ethernet Ring, as identified by the Ethernet Ring ID, a VPLS service (4294967295), or is not interconnected (0). A sub-ring can only be interconnected to a VPLS service (i.e. tmnxEthRingSubRingInterconnectId assigned the value 4294967295), if tmnxEthRingSubRingType is assigned the value 'nonVirtualLink (2)'. This object MUST be set to a value other than zero (0) for tmnxEthRingSubRingPropTopChange to be modified away from its default value. Attempts to modify this object away from its default value when tmnxEthRingSubRingType is set to 'none (0)' will result in an SNMP inconsistentValue error.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 1..4294967294 | 4294967295  

tmnxEthRingSubRingPropTopChange 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.18
The value of tmnxEthRingSubRingPropTopChange specifies whether or not the Ethernet sub-ring propagates topology changes to the interconnected ring as specified by the value of tmnxEthRingSubRingInterconnectId. Attempts to modify this object away from its default value when tmnxEthRingSubRingInterconnectId is set to zero (0) will result in an SNMP inconsistentValue error.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

tmnxEthRingCompatibleVersion 1.3.6.1.4.1.6527.3.1.2.72.1.1.1.19
The value of tmnxEthRingCompatibleVersion specifies the backward compatibility logic for the Ethernet Ring. If this object is set to 'version1 (1)' then: 1. Attempts at setting tmnxEthRingCommandSwitch to the value 'forceSwitch (2)' or 'manualSwitch (3)' will result in an inconsistentValue error, and 2. Attempts at setting tmnxEthRingRevertTime to the value zero (0) will result in an inconsistentValue error. If this object is set to 'version2 (2)' then the above restrictions will not apply.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER version1(1), version2(2)  

tmnxEthRingPathTblLastChanged 1.3.6.1.4.1.6527.3.1.2.72.0.2
The tmnxEthRingPathTblLastChanged indicates the time, since system startup, when a row in the tmnxEthRingPathTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingPathTable 1.3.6.1.4.1.6527.3.1.2.72.1.3
The tmnxEthRingPathTable consists of the paths associated with the corresponding tmnxEthRingConfigEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthRingPathEntry

tmnxEthRingPathEntry 1.3.6.1.4.1.6527.3.1.2.72.1.3.1
The tmnxEthRingPathEntry contains information pertaining to an individual path associated with a tmnxEthRingConfigEntry. Rows in this table are created and destroyed using the tmnxEthRingPathRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingPathEntry  

tmnxEthRingPathIndex 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.1
The tmnxEthRingPathIndex specifies the row index of the member.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingPathIndex  

tmnxEthRingPathRowStatus 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.2
The tmnxEthRingPathRowStatus, along with tmnxEthRingPathIfIndex and tmnxEthRingPathIfRapsCcTag, control the creation and deletion of row entries in the tmnxEthRingPathTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxEthRingPathTimeStamp 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.3
The value of tmnxEthRingPathTimeStamp indicates the time, since system startup, of the last change to this row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingPathIfIndex 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.4
The value of tmnxEthRingPathIfIndex specifies the member's port tmnxPortPortID associated with the tmnxEthRingConfigEntry. This object must be included in the same SNMP PDU as that of the tmnxEthRingPathRowStatus object for creation of the path. The absense of this object will result in a NO CREATION error. The tmnxEthRingPathIfIndex can not be changed; the row must be destroyed and re-created.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

tmnxEthRingPathIfRapsCcTag 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.5
The value of tmnxEthRingPathIfRapsCcTag specifies the member's encapsulation. This object must be included in the same SNMP PDU as that of the tmnxEthRingPathRowStatus object for creation of the path. The absense of this object will result in a NO CREATION ERROR Once specified, the tmnxEthRingPathIfRapsCcTag can not be changed; the row must be destroyed and re-created.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEncapVal  

tmnxEthRingPathDescription 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.6
The value of tmnxEthRingPathDescription specifies a detailed description of the Ethernet Ring path.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxEthRingPathAdminStatus 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.7
The value of tmnxEthRingPathAdminStatus specifies the administrative state of the path. 'outOfService (3)' specifies that the member will not partake in Ring Redundancy.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxEthRingPathOperStatus 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.8
The tmnxEthRingPathOperStatus indicates the operational state of of the path. The tmnxEthRingPathOperStatus supports the following two TmnxOperState values: inService (2) outOfService (3)
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxEthRingPathType 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.9
The value of tmnxEthRingPathType specifies the Ethernet Ring Node Path acts as an rplEnd or in a normal state. This is only configurable if tmnxEthRingRplNode is set to 'rplOwner (1)' or 'rplNeighbor (2)'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER normal(0), rplEnd(1)  

tmnxEthRingPathFwdState 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.10
The value of tmnxEthRingPathFwdState indicates whether the Ethernet Ring Node Path blocks the transmission and reception of traffic on the ring port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unblocked(0), blocked(1)  

tmnxEthRingPathFwdStateChgTime 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.11
The value of tmnxEthRingPathFwdStateChgTime indicates the time, since system startup, that the Ethernet Ring Path last experienced a change in the forwarding state.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingPathRxApsPdu 1.3.6.1.4.1.6527.3.1.2.72.1.3.1.12
The value of tmnxEthRingPathRxApsPdu indicates the contents of the R-APS PDU received on the Ethernet Ring path.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxEthRingApsInfoType  

tmnxEthRingSAPConfigs 1.3.6.1.4.1.6527.3.1.2.72.1.4
OBJECT IDENTIFIER    

tmnxEthRingSAPPathTblChanged 1.3.6.1.4.1.6527.3.1.2.72.0.4
The tmnxEthRingSAPPathTblChanged indicates the time, since system startup, when a row in the tmnxEthRingSAPPathTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthRingSAPPathTable 1.3.6.1.4.1.6527.3.1.2.72.1.4.1
The tmnxEthRingSAPPathTable consists of the configuration for Ethernet Ring Group members associated to SAPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthRingSAPPathEntry

tmnxEthRingSAPPathEntry 1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1
The tmnxEthRingSAPPathEntry contains the SAP information pertaining to an Ethernet Ring Group member. Entries in the tmnxEthRingSAPPathTable are created and destroyed by the system when the TIMETRA-SAP-MIB::sapEthRingIndex is set to a non-zero value during the creation of a row in the TIMETRA-SAP-MIB::sapBaseInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingSAPPathEntry  

tmnxEthRingSAPPathIndex 1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1.1
The value of tmnxEthRingSAPPathIndex indicates the corresponding path index of the tmnxEthRingPathEntry for this row.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxEthRingSAPPathControlFlag 1.3.6.1.4.1.6527.3.1.2.72.1.4.1.1.2
The value of tmnxEthRingSAPPathControlFlag indicates whether or not this row corresponds to the control SAP of the tmnxEthRingConfigEntry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tmnxEthRingCommandTable 1.3.6.1.4.1.6527.3.1.2.72.1.5
The tmnxEthRingCommandTable consists of the one-shot action commands that effect the state of the Ethernet Ring operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthRingCommandEntry

tmnxEthRingCommandEntry 1.3.6.1.4.1.6527.3.1.2.72.1.5.1
The tmnxEthRingCommandEntry contains the commands available to execute on an existing Ethernet Ring Group Path. Rows in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthRingCommandEntry  

tmnxEthRingCommandSwitch 1.3.6.1.4.1.6527.3.1.2.72.1.5.1.1
The value of tmnxEthRingCommandSwitch specifies the switch command to initiate on a path of an Ethernet Ring Group. When read, this object returns the last command written or 'noCmd (0)' if no command has been written to this Ethernet Ring Group path since initialization. The return of the last command written does not imply that this command is currently in effect. The request may be preempted by a higher priority local or remote request. In order to determine the current state of the group it is necessary to read the objects tmnxEthRingPathRxApsPdu and tmnxEthRingTxApsPdu. The value 'noCmd (0)' may not be used in a write command. The value 'clear (1)' clears all the switch commands listed below for the specified ring, regardless of the specified path. In addition, if tmnxEthRingRevertTime is a non-zero value (revertive mode) the active WTR (Wait To Restore) state is also cleared, or in the case of non-revertive mode, the command will trigger a reversion. The 'clear (1)' command is only valid if at least one path is configured and either: 1. a local Forced Switch or Manual Switch command is in effect, or 2. a local Ethernet Ring Node is an RPL Owner Node and top priority request is neither R-APS (FS) nor R-APS (MS). The value 'forceSwitch (2)' forces the specified path's tmnxEthRingPathFwdState to the 'blocked (1)' state. The value 'manualSwitch (3)' sets the specified path's tmnxEthRingPathFwdState to the 'blocked (1)' state in the absence of a failure or forceSwitch. An inconsistentValue error is returned, otherwise.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noCmd(0), clear(1), forceSwitch(2), manualSwitch(3)  

tmnxEthRingOprNotifications 1.3.6.1.4.1.6527.3.1.3.72.0.1
OBJECT IDENTIFIER    

tmnxEthRingPathFwdStateChange 1.3.6.1.4.1.6527.3.1.3.72.0.1.1
The tmnxEthRingPathFwdStateChange is generated when an Ethernet Ring Path changes its forwarding state (tmnxEthRingPathFwdState) from blocked to unblocked or from unblocked to blocked.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthRingApsNotifications 1.3.6.1.4.1.6527.3.1.3.72.0.2
OBJECT IDENTIFIER    

tmnxEthRingApsPrvsnRaiseAlarm 1.3.6.1.4.1.6527.3.1.3.72.0.2.1
The tmnxEthRingApsPrvsnRaiseAlarm is generated when an Ethernet Ring provisioning mismatch is detected. A mismatch occurs when the RPL Owner Node receives one or more No Request R-APS message(s) with RPL Blocked status flag set (NR,RB) and a Node ID that differs from its own.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthRingApsPrvsnClearAlarm 1.3.6.1.4.1.6527.3.1.3.72.0.2.2
The tmnxEthRingApsPrvsnClearAlarm is generated when an Ethernet Ring provisioning mismatch is cleared.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthRingCompliance 1.3.6.1.4.1.6527.3.1.1.72.1.1
The compliance statement for revision 1.0 of TIMETRA-ETH-RING-MIB.
Status: obsolete Access: read-create
MODULE-COMPLIANCE    

tmnxEthRingV9v0Compliance 1.3.6.1.4.1.6527.3.1.1.72.1.2
The compliance statement for revision 9.0 of TIMETRA-ETH-RING-MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

tmnxEthRingTSGroups 1.3.6.1.4.1.6527.3.1.1.72.2.0
OBJECT IDENTIFIER    

tmnxEthRingTimeStampGroup 1.3.6.1.4.1.6527.3.1.1.72.2.0.1
The group of objects that track configuration changes for the maintenance of Ethernet Rings for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingConfigGroups 1.3.6.1.4.1.6527.3.1.1.72.2.1
OBJECT IDENTIFIER    

tmnxEthRingBaseConfigGroup 1.3.6.1.4.1.6527.3.1.1.72.2.1.1
The group of objects for management of Ethernet Ring Group configurations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingOperGroups 1.3.6.1.4.1.6527.3.1.1.72.2.2
OBJECT IDENTIFIER    

tmnxEthRingMemberGroups 1.3.6.1.4.1.6527.3.1.1.72.2.3
OBJECT IDENTIFIER    

tmnxEthRingBasePathGroup 1.3.6.1.4.1.6527.3.1.1.72.2.3.1
The group of objects for management of Ethernet Ring Group Member configurations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingAPSGroups 1.3.6.1.4.1.6527.3.1.1.72.2.4
OBJECT IDENTIFIER    

tmnxEthRingNotifyGroups 1.3.6.1.4.1.6527.3.1.1.72.2.5
OBJECT IDENTIFIER    

tmnxEthRingOperNotifyGroup 1.3.6.1.4.1.6527.3.1.1.72.2.5.1
The group of notifications for management of Ethernet Ring Group configurations for the SR series systems.
Status: current Access: read-create
NOTIFICATION-GROUP    

tmnxEthRingApsNotifyGroup 1.3.6.1.4.1.6527.3.1.1.72.2.5.2
The group of notifications for management of Ethernet Ring Group APS configurations for the SR series systems.
Status: current Access: read-create
NOTIFICATION-GROUP    

tmnxEthRingSAPGroups 1.3.6.1.4.1.6527.3.1.1.72.2.6
OBJECT IDENTIFIER    

tmnxEthRingSAPPathGroup 1.3.6.1.4.1.6527.3.1.1.72.2.6.1
The group of objects added in Release 8.0 to support configuration and maintenance of Ethernet Ring Groups on SAPs for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingV9v0Groups 1.3.6.1.4.1.6527.3.1.1.72.2.7
OBJECT IDENTIFIER    

tmnxEthRingBaseConfigV9v0Group 1.3.6.1.4.1.6527.3.1.1.72.2.7.1
The group of objects added in Release 9.0 to support configuration and maintenance of Ethernet Rings for the SROS series systems.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingSubRingV9v0Group 1.3.6.1.4.1.6527.3.1.1.72.2.7.2
The group of objects added in Release 9.0 to support configuration and maintenance of Ethernet sub-rings for the SROS series systems.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthRingCommandV9v0Group 1.3.6.1.4.1.6527.3.1.1.72.2.7.3
The group of objects added in Release 9.0 to support maintenance of Ethernet Rings for the SROS series systems.
Status: current Access: read-create
OBJECT-GROUP