TIMETRA-VRRP-V3-MIB

File: TIMETRA-VRRP-V3-MIB.mib (32747 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB INET-ADDRESS-MIB VRRP-MIB
TIMETRA-GLOBAL-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Integer32 Unsigned32
RowStatus MacAddress TruthValue
TimeStamp TimeInterval StorageType
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
ifIndex InetAddressType InetAddress
VrId vrrpOperations vrrpStatistics
vrrpNotifications vrrpMIBCompliances vrrpMIBGroups
timetraSRMIBModules

Defined Types

VrrpOperationsEntry  
SEQUENCE    
  vrrpOperationsInetAddrType InetAddressType
  vrrpOperationsVrId VrId
  vrrpOperationsVirtualMacAddr MacAddress
  vrrpOperationsState INTEGER
  vrrpOperationsPriority Unsigned32
  vrrpOperationsAddrCount Integer32
  vrrpOperationsMasterIpAddr InetAddress
  vrrpOperationsPrimaryIpAddr InetAddress
  vrrpOperationsAdvInterval TimeInterval
  vrrpOperationsPreemptMode TruthValue
  vrrpOperationsAcceptMode TruthValue
  vrrpOperationsUpTime TimeStamp
  vrrpOperationsStorageType StorageType
  vrrpOperationsRowStatus RowStatus

VrrpAssociatedIpAddrEntry  
SEQUENCE    
  vrrpAssociatedIpAddr InetAddress
  vrrpAssociatedStorageType StorageType
  vrrpAssociatedIpAddrRowStatus RowStatus

VrrpRouterStatisticsEntry  
SEQUENCE    
  vrrpStatisticsMasterTransitions Counter32
  vrrpStatisticsRcvdAdvertisements Counter32
  vrrpStatisticsAdvIntervalErrors Counter32
  vrrpStatisticsIpTtlErrors Counter32
  vrrpStatisticsRcvdPriZeroPackets Counter32
  vrrpStatisticsSentPriZeroPackets Counter32
  vrrpStatisticsRcvdInvalidTypePkts Counter32
  vrrpStatisticsAddressListErrors Counter32
  vrrpStatisticsPacketLengthErrors Counter32
  vrrpStatisticsRcvdInvalidAuthentications Counter32
  vrrpStatisticsDiscontinuityTime TimeStamp
  vrrpStatisticsRefreshRate Unsigned32

Defined Values

timetraVrrpV3MibModule 1.3.6.1.4.1.6527.1.1.3.57
This MIB is based on the draft-ietf-vrrp-unified-mib-06.txt and describes objects used for managing Virtual Router Redundancy Protocol (VRRP) over IPv6 protocol. A separate VRRP-MIB based on RFC2787 describes objects used for managing VRRP over IPv4 protocol. This MIB is subject to draft revisions and will be updated when an RFC number is assigned to it. Copyright (c) 2008-2011 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

vrrpOperationsTable 1.3.6.1.2.1.68.1.7
Unified Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'vrrpOperationsEntry' items which describe the operational characteristics of a virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VrrpOperationsEntry

vrrpOperationsEntry 1.3.6.1.2.1.68.1.7.1
An entry in the vrrpOperationsTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IP version, VRID and ifIndex. ifIndex represents a physical interface of the router. Note that rows in this table can be distinguished on a multi-stacked device running VRRP over IPv4 and IPv6 on the same physical interface. Rows in the table cannot be modified unless the value of 'vrrpOperationsState' has transitioned to 'initialize'
Status: current Access: not-accessible
OBJECT-TYPE    
  VrrpOperationsEntry  

vrrpOperationsInetAddrType 1.3.6.1.2.1.68.1.7.1.1
The IP address type of VrrpOperationsEntry. This value applies to both vrrpOperationsMasterIpAddr and vrrpOperationsPrimaryIpAddr.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

vrrpOperationsVrId 1.3.6.1.2.1.68.1.7.1.2
This object contains the Virtual Router Identifier (VRID).
Status: current Access: not-accessible
OBJECT-TYPE    
  VrId  

vrrpOperationsVirtualMacAddr 1.3.6.1.2.1.68.1.7.1.3
The virtual MAC address of the virtual router. Although this object can be derived from the 'vrrpOperationsVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP notifications.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

vrrpOperationsState 1.3.6.1.2.1.68.1.7.1.4
The current state of the virtual router. This object has three defined values: - `initialize', which indicates that the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), backup(2), master(3)  

vrrpOperationsPriority 1.3.6.1.2.1.68.1.7.1.5
This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es) for VRRP over IPv4 and hence not settable. A 'badValue(3)' should be returned when a user tries to set 0 or 255 for this object.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

vrrpOperationsAddrCount 1.3.6.1.2.1.68.1.7.1.6
The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the vrrpAssociatedIpAddrTable that correspond to a given IP version/VRID/ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

vrrpOperationsMasterIpAddr 1.3.6.1.2.1.68.1.7.1.7
The master router's real IP address. Master router would set this address to vrrpOperationsPrimaryIpAddr while transitioning to master state. For backup routers, this is the IP address listed as the source in VRRP advertisement last received by this virtual router.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vrrpOperationsPrimaryIpAddr 1.3.6.1.2.1.68.1.7.1.8
In the case where there are more than one IP Address (associated IP addresses) for a given `ifIndex', this object is used to specify the IP address that will become the 'vrrpOperationsMasterIpAddr', should the virtual router transition from backup state to master.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vrrpOperationsAdvInterval 1.3.6.1.2.1.68.1.7.1.9
The time interval, in centiseconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval 1..4095  

vrrpOperationsPreemptMode 1.3.6.1.2.1.68.1.7.1.10
Controls whether a higher priority virtual router will preempt a lower priority master.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vrrpOperationsAcceptMode 1.3.6.1.2.1.68.1.7.1.11
Controls whether a virtual router in Master state will accept packets addressed to the address owner's IPv6 address as its own if it is not the IPv6 address owner. Default is False. This object is not relevant for rows representing VRRP over IPv4 and should be set to false.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vrrpOperationsUpTime 1.3.6.1.2.1.68.1.7.1.12
This is the value of the `sysUpTime' object when this virtual router (i.e., the `vrrpOperationsState') transitioned out of `initialized'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vrrpOperationsStorageType 1.3.6.1.2.1.68.1.7.1.13
The storage type for this conceptual row. Write access is not required. It is optional to support nonVolatile StorageType enumeration.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

vrrpOperationsRowStatus 1.3.6.1.2.1.68.1.7.1.14
The RowStatus variable should be used in accordance to installation and removal conventions for conceptual rows. When `vrrpOperationsRowStatus' is set to active(1), no other objects in the conceptual row can be modified. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `vrrpOperationsRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of vrrpOperationsInetAddrType, vrrpOperationsVrId and vrrpOperationsPrimaryIpAddr has been set and there is at least one active row in the `vrrpAssociatedIpAddrTable' defining an associated IP address. notInService(2) should be used to administratively bring the row down. A typical order of operation to add a row is: 1. Create a row in vrrpOperationsTable with createAndWait(5). 2. Create one or more corresponding rows in vrrpAssociatedIpAddrTable. 3. Populate the vrrpOperationsEntry. 4. set vrrpOperationsRowStatus to active(1). A typical order of operation to delete an entry is: 1. Set vrrpOperationsRowStatus to notInService(2). 2. Set the corresponding rows in vrrpAssociatedIpAddrTable to destroy(6) to delete the entry. 3. set vrrpOperationsRowStatus to destroy(6) to delete the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vrrpAssociatedIpAddrTable 1.3.6.1.2.1.68.1.8
The table of addresses associated with this virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VrrpAssociatedIpAddrEntry

vrrpAssociatedIpAddrEntry 1.3.6.1.2.1.68.1.8.1
An entry in the table contains an IP address that is associated with a virtual router. The number of rows for a given IP version, vrrpOperationsVrId and ifIndex will equal the number of IP addresses associated (e.g., backed up) by the virtual router (equivalent to 'vrrpOperationsIpAddrCount'). Rows in the table cannot be modified unless the value of `vrrpOperationsState' has transitioned to `initialize'.
Status: current Access: not-accessible
OBJECT-TYPE    
  VrrpAssociatedIpAddrEntry  

vrrpAssociatedIpAddr 1.3.6.1.2.1.68.1.8.1.1
The assigned IP addresses that a virtual router is responsible for backing up. The size of this object is either 4 or 16 depending on vrrpOperationsInetAddrType.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

vrrpAssociatedStorageType 1.3.6.1.2.1.68.1.8.1.2
The storage type for this conceptual row. Write access is not required. It is optional to support nonVolatile StorageType enumeration.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

vrrpAssociatedIpAddrRowStatus 1.3.6.1.2.1.68.1.8.1.3
The RowStatus variable, used according to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Setting this object to active(1) results in the addition of an associated address for a virtual router. Setting this object to notInService(2) results in administratively bringing down the row. Destroying the entry or setting it to destroy(6) removes the associated address from the virtual router. The use of other values is implementation-dependent. Only vrrpAssociatedStorageType can be modified when the row is in active(1) state for Implementations supporting write access to vrrpAssociatedStorageType Implementations should not allow deletion of the last row corresponding to an active row in vrrpOperationsTable. Refer to description of vrrpOperationsRowStatus for a typical row creation and deletion scenarios.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vrrpRouterStatisticsTable 1.3.6.1.2.1.68.2.5
Table of virtual router statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VrrpRouterStatisticsEntry

vrrpRouterStatisticsEntry 1.3.6.1.2.1.68.2.5.1
An entry in the table, containing statistics information about a given virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  VrrpRouterStatisticsEntry  

vrrpStatisticsMasterTransitions 1.3.6.1.2.1.68.2.5.1.1
The total number of times that this virtual router's state has transitioned to MASTER. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsRcvdAdvertisements 1.3.6.1.2.1.68.2.5.1.2
The total number of VRRP advertisements received by this virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsAdvIntervalErrors 1.3.6.1.2.1.68.2.5.1.3
The total number of VRRP advertisement packets received for which the advertisement interval is different than the one configured for the local virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsIpTtlErrors 1.3.6.1.2.1.68.2.5.1.4
The total number of VRRP packets received by the Virtual router with IPv4 TTL (for VRRP over IPv4) or IPv6 Hop Limit (for VRRP over IPv6) not equal to 255. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsRcvdPriZeroPackets 1.3.6.1.2.1.68.2.5.1.5
The total number of VRRP packets received by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsSentPriZeroPackets 1.3.6.1.2.1.68.2.5.1.6
The total number of VRRP packets sent by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsRcvdInvalidTypePkts 1.3.6.1.2.1.68.2.5.1.7
The number of VRRP packets received by the virtual router with an invalid value in the 'type' field. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsAddressListErrors 1.3.6.1.2.1.68.2.5.1.8
The total number of packets received for which the address list does not match the locally configured list for the virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsPacketLengthErrors 1.3.6.1.2.1.68.2.5.1.9
The total number of packets received with a packet length less than the length of the VRRP header. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsRcvdInvalidAuthentications 1.3.6.1.2.1.68.2.5.1.10
The total number of packets received with an unknown authentication type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpStatisticsDiscontinuityTime 1.3.6.1.2.1.68.2.5.1.11
The value of sysUpTime on the most recent occasion at which any one or more of this entry's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vrrpStatisticsRefreshRate 1.3.6.1.2.1.68.2.5.1.12
The minimum reasonable polling interval for this entry. This object provides an indication of the minimum Amount of time required to update the counters in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vrrpNewMasterReason 1.3.6.1.2.1.68.1.9
This indicates the reason for tVrrpTrapNewMaster trap. Used by tVrrpTrapNewMaster trap. The object can be polled if the tVrrpTrapNewMaster trap is lost to identify the reason for transmission. Backup router should return notmaster(0) when pooled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notmaster(0), priority(1), preempted(2), masterNoResponse(3)  

vrrpTrapProtoErrReason 1.3.6.1.2.1.68.1.10
This indicates the reason for protocol error trap. Used by vrrpTrapProtoError trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER hopLimitError(0), versionError(1), checksumError(2), vridError(3)  

vrrpTrapProtoError 1.3.6.1.2.1.68.0.3
The error trap indicates that the sending agent has encountered the protocol error indicated by vrrpTrapProtoErrReason.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

vrrpModuleFullCompliance 1.3.6.1.2.1.68.3.1.2
The compliance statement for both VRRP for IPv4 and VRRP for IPv6 implementations.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

vrrpModuleReadOnlyCompliance 1.3.6.1.2.1.68.3.1.3
When this MIB is implemented without support for read- create (i.e. in read-only mode), then such an implementation can claim read-only compliance. Such a device can then be monitored but can not be configured with this MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

vrrpOperationsGroup 1.3.6.1.2.1.68.3.2.5
Conformance group for VRRP over IPv4 and IPv6 operations.
Status: current Access: read-only
OBJECT-GROUP    

vrrpStatisticsGroup 1.3.6.1.2.1.68.3.2.6
Conformance group for VRRP over IPv4 and IPv6 statistics.
Status: current Access: read-only
OBJECT-GROUP    

vrrpTrapInfoGroup 1.3.6.1.2.1.68.3.2.7
Conformance group for objects contained in VRRP notifications.
Status: current Access: read-only
OBJECT-GROUP    

vrrpNotificationsGroup 1.3.6.1.2.1.68.3.2.8
The VRRP MIB Notification Group.
Status: current Access: read-only
NOTIFICATION-GROUP    

vrrpNotifyObjsGroup 1.3.6.1.2.1.68.3.2.9
Conformance group for Notify objects contained in VRRP notifications.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor