TNI-MIB

File: TNI-MIB.mib (148145 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

Counter enterprises Gauge
TimeTicks IpAddress DisplayString
PhysAddress OBJECT-TYPE TRAP-TYPE

Defined Types

MacAddress  
OCTET STRING Size(6)    

CpsConnector  
INTEGER rj-45(10), stmm(11), stsm(12), scmm(13), scsm(14), scsmlh(15), scsmelh(16), scsmlhlw(17), mtrjmm(18), lc(19), bnc(20), stsmlh(21), stsmelh(22), scmm1300(23), stmm1300(24), mtrjsm(25), serial26(26), stmmlh(27), scsmsh(28), scsimplex(29), bncdual(30), db9rsxxx(31), termblock(32), rj11(33), sc40km(34), sc125km(35), din6(38)    

SpsIpAddrEntry  
SEQUENCE    
  spsIpIfIndex INTEGER
  spsIpAddr IpAddress
  spsIpNetMask IpAddress

SpsTrapEntry  
SEQUENCE    
  spsTrapIndex INTEGER
  spsTrapDestination IpAddress
  spsTrapCommunity DisplayString

SpsRptrGroupEntry  
SEQUENCE    
  spsRptrGroupIndex INTEGER
  spsRptrGroupUnitId OCTET STRING
  spsRptrGroupInternalPowerSupply INTEGER

SpsRptrPortEntry  
SEQUENCE    
  spsRptrPortGroupIndex INTEGER
  spsRptrPortIndex INTEGER
  spsRptrPortSegment INTEGER
  spsRptrPortSrcAddr MacAddress
  spsRptrPortEavesdropping INTEGER
  spsRptrPortIntrusion INTEGER
  spsRptrPortCollisionLimit INTEGER
  spsRptrPortEnableIntruderDetectTrap INTEGER
  spsRptrPortDisableIntruder INTEGER

SpsSerialPortEntry  
SEQUENCE    
  spsSerialPortIndex INTEGER
  spsSerialPortModemControl INTEGER

SpsMonitorSegmentEntry  
SEQUENCE    
  spsMonitorSegmentIndex INTEGER
  spsMonitorSegmentTotalFrames Counter
  spsMonitorSegmentTotalOctets Counter
  spsMonitorSegmentTotalErrors Counter

Sfbrm100SystemEntry  
SEQUENCE    
  sfbrm100SysLocPortIndex INTEGER
  sfbrm100SysSecIndex INTEGER
  sfbrm100SysGrpString DisplayString
  sfbrm100SysMRevision INTEGER
  sfbrm100SysCfgMatch INTEGER
  sfbrm100SysBootLoaderRevision OCTET STRING
  sfbrm100SysFirmwareRevision OCTET STRING
  sfbrm100SysSerialNumber INTEGER
  sfbrm100SysBIAddress INTEGER
  sfbrm100SysSlotIndex INTEGER
  sfbrm100SysNumPorts INTEGER
  sfbrm100SysMACAddress PhysAddress
  sfbrm100SystemReset INTEGER
  sfbrm100SysIPaddress IpAddress
  sfbrm100SysSubnetMask IpAddress
  sfbrm100SysDefGateway IpAddress
  sfbrm100SysSNMPTrapMgr IpAddress
  sfbrm100SysRadiusAuth INTEGER
  sfbrm100SysRadiusServerAddr IpAddress
  sfbrm100SysRadiusSecret OCTET STRING
  sfbrm100SysRadiusRetry INTEGER
  sfbrm100SysRadiusTimeout INTEGER
  sfbrm100SysDHCPEnable INTEGER
  sfbrm100SysSerialAccess INTEGER
  sfbrm100SysTLPT INTEGER
  sfbrm100SysTFTPServerAddr IpAddress
  sfbrm100SysTFTPfilename OCTET STRING
  sfbrm100SysTFTPCmd INTEGER
  sfbrm100SysTFTPServerIgnore INTEGER
  sfbrm100SysMgmtVlanId INTEGER
  sfbrm100SysSNMPAccess INTEGER
  sfbrm100SysIPAccess INTEGER
  sfbrm100SysLastGaspPdu INTEGER
  sfbrm100SysLastGaspPort INTEGER
  sfbrm100SysLocalLPT INTEGER
  sfbrm100SysLPTPort INTEGER
  sfbrm100SysAutoUpgrade INTEGER
  sfbrm100SysFormFactorSlot INTEGER
  sfbrm100SysFormFactorPort INTEGER
  sfbrm100SysOAMPort INTEGER

Sfbrm100SwEntry  
SEQUENCE    
  sfbrm100SwPortIndex INTEGER
  sfbrm100SwSecIndex INTEGER
  sfbrm100SwATUAgeTimeout INTEGER
  sfbrm100SwIngressMonPort INTEGER
  sfbrm100SwEgressMonPort INTEGER
  sfbrm100SwFactoryDefaults INTEGER
  sfbrm100SwResetCounters INTEGER
  sfbrm100SwHistMode INTEGER
  sfbrm100SwIEEEPriRemap0 INTEGER
  sfbrm100SwIEEEPriRemap1 INTEGER
  sfbrm100SwIEEEPriRemap2 INTEGER
  sfbrm100SwIEEEPriRemap3 INTEGER
  sfbrm100SwIEEEPriRemap4 INTEGER
  sfbrm100SwIEEEPriRemap5 INTEGER
  sfbrm100SwIEEEPriRemap6 INTEGER
  sfbrm100SwIEEEPriRemap7 INTEGER
  sfbrm100SwFlushFdb INTEGER
  sfbrm100SwFlushVlandb INTEGER
  sfbrm100SwUseDoubleTagData INTEGER
  sfbrm100SwFiberRedundancy INTEGER
  sfbrm100SwFiberRedundRevert INTEGER
  sfbrm100SwFbrRedundActivePort INTEGER
  sfbrm100SwSupressVlanViolations INTEGER
  sfbrm100SwSupressMACViolations INTEGER

Sfbrm100SwIPPrioEntry  
SEQUENCE    
  sfbrm100SwIPPrioPortIndex INTEGER
  sfbrm100SwIPPrioIndex INTEGER
  sfbrm100SwIPPrioTC INTEGER
  sfbrm100SwIPPrioRemap INTEGER

Sfbrm100PortEntry  
SEQUENCE    
  sfbrm100PortLocIndex INTEGER
  sfbrm100PortRmtIndex INTEGER
  sfbrm100PortGrpString DisplayString
  sfbrm100PortConnType CpsConnector
  sfbrm100PortOAMState INTEGER
  sfbrm100PortOAMModeCtrl INTEGER
  sfbrm100PortRmtLoopback INTEGER
  sfbrm100PortIgnoreLoopback INTEGER
  sfbrm100PortAdvPause INTEGER
  sfbrm100PortAdv1000FDX INTEGER
  sfbrm100PortAdv1000HDX INTEGER
  sfbrm100PortAdv100FDX INTEGER
  sfbrm100PortAdv100HDX INTEGER
  sfbrm100PortAdv10FDX INTEGER
  sfbrm100PortAdv10HDX INTEGER
  sfbrm100PortAutoneg INTEGER
  sfbrm100PortFDuplex INTEGER
  sfbrm100PortFSpeed INTEGER
  sfbrm100PortLpPauseAbility INTEGER
  sfbrm100PortLpAutonegAbility INTEGER
  sfbrm100PortLinkState INTEGER
  sfbrm100PortAutonegState INTEGER
  sfbrm100PortDuplex INTEGER
  sfbrm100PortSpeed INTEGER
  sfbrm100PortFEFI INTEGER
  sfbrm100PortAutocross INTEGER
  sfbrm100PortLock INTEGER
  sfbrm100PortIgnoreWrongData INTEGER
  sfbrm100PortIGMPSnoop INTEGER
  sfbrm100PortDoubleTagging INTEGER
  sfbrm100PortUseIPTC INTEGER
  sfbrm100PortUseTagTC INTEGER
  sfbrm100PortUseBothTC INTEGER
  sfbrm100PortVLANTunnel INTEGER
  sfbrm100PortFwdUnknown INTEGER
  sfbrm100PortDefForward INTEGER
  sfbrm100PortAdminState INTEGER
  sfbrm100PortVTUPriOverride INTEGER
  sfbrm100PortSAPriOverride INTEGER
  sfbrm100PortDAPriOverride INTEGER
  sfbrm100PortVLANStatus INTEGER
  sfbrm100PortDiscardTagged INTEGER
  sfbrm100PortDiscardUntagged INTEGER
  sfbrm100PortEgressMonitor INTEGER
  sfbrm100PortIngressMonitor INTEGER
  sfbrm100PortPri3IngressRateCtrl INTEGER
  sfbrm100PortPri2IngressRateCtrl INTEGER
  sfbrm100PortPri1IngressRateCtrl INTEGER
  sfbrm100PortPri0IngressRate INTEGER
  sfbrm100PortIngressLimitMode INTEGER
  sfbrm100PortEgressRate INTEGER
  sfbrm100PortDefaultPriority INTEGER
  sfbrm100PortForceDefVLANId INTEGER
  sfbrm100PortDefaultVLANId INTEGER
  sfbrm100PortBasedVLANTbl INTEGER
  sfbrm100PortIEEEPriRemap0 INTEGER
  sfbrm100PortIEEEPriRemap1 INTEGER
  sfbrm100PortIEEEPriRemap2 INTEGER
  sfbrm100PortIEEEPriRemap3 INTEGER
  sfbrm100PortIEEEPriRemap4 INTEGER
  sfbrm100PortIEEEPriRemap5 INTEGER
  sfbrm100PortIEEEPriRemap6 INTEGER
  sfbrm100PortIEEEPriRemap7 INTEGER
  sfbrm100PortVCTest INTEGER
  sfbrm100PortVCTxMDI0Status INTEGER
  sfbrm100PortTxMDI0Dist INTEGER
  sfbrm100PortVCRxMDI1Status INTEGER
  sfbrm100PortRxMDI1Dist INTEGER
  sfbrm100PortVCMDI2Status INTEGER
  sfbrm100PortMDI2Dist INTEGER
  sfbrm100PortVCMDI3Status INTEGER
  sfbrm100PortMDI3Dist INTEGER
  sfbrm100PortResetCounters INTEGER
  sfbrm100PortIPTrafficAccess INTEGER
  sfbrm100PortResetOAMCounters INTEGER
  sfbrm100PortForceAutoUpgrade INTEGER
  sfbrm100PortModeType INTEGER
  sfbrm100PortOAMMode INTEGER
  sfbrm100PortPhyNumber INTEGER
  sfbrm100PortIngressRateLimit2 INTEGER
  sfbrm100PortEgressRateLimit2 INTEGER

Sfbrm100PortStatsEntry  
SEQUENCE    
  sfbrm100PortLocStatsIndex INTEGER
  sfbrm100PortRmtStatsIndex INTEGER
  sfbrm100PortInGoodOctetsLo INTEGER
  sfbrm100PortInGoodOctetsHi INTEGER
  sfbrm100PortInBadOctets INTEGER
  sfbrm100PortInUnicasts INTEGER
  sfbrm100PortInBroadcasts INTEGER
  sfbrm100PortInMulticasts INTEGER
  sfbrm100PortInPause INTEGER
  sfbrm100PortInUndersize INTEGER
  sfbrm100PortInFragments INTEGER
  sfbrm100PortInOversize INTEGER
  sfbrm100PortInJabber INTEGER
  sfbrm100PortInRxErr INTEGER
  sfbrm100PortInFCSErr INTEGER
  sfbrm100PortIn64Octets INTEGER
  sfbrm100PortIn65to127Octets INTEGER
  sfbrm100PortIn128to255Octets INTEGER
  sfbrm100PortIn256to511Octets INTEGER
  sfbrm100PortIn512to1023Octets INTEGER
  sfbrm100PortIn1024toMaxOctets INTEGER
  sfbrm100PortOutOctetsLo INTEGER
  sfbrm100PortOutOctetsHi INTEGER
  sfbrm100PortOutUnicasts INTEGER
  sfbrm100PortOutBroadcasts INTEGER
  sfbrm100PortOutMulticasts INTEGER
  sfbrm100PortOutPause INTEGER
  sfbrm100PortOutDeferred INTEGER
  sfbrm100PortOutCollisions INTEGER
  sfbrm100PortOutSingle INTEGER
  sfbrm100PortOutMultiple INTEGER
  sfbrm100PortOutExcessive INTEGER
  sfbrm100PortOutLate INTEGER
  sfbrm100PortOutFCSErr INTEGER
  sfbrm100PortInDiscard INTEGER
  sfbrm100PortInFiltered INTEGER
  sfbrm100PortOutFiltered INTEGER

Sfbrm100DMIEntry  
SEQUENCE    
  sfbrm100DMILocPortIndex INTEGER
  sfbrm100DMIRmtPortIndex INTEGER
  sfbrm100DMIRxPwrLvlPreset INTEGER
  sfbrm100DMIConnType CpsConnector
  sfbrm100DMIBitRate INTEGER
  sfbrm100DMILenFor9x125umKM INTEGER
  sfbrm100DMILenFor9x125um100M INTEGER
  sfbrm100DMILenFor50x125um10M INTEGER
  sfbrm100DMILenFor625x125um10M INTEGER
  sfbrm100DMILenForCopper INTEGER
  sfbrm100DMIId INTEGER
  sfbrm100DMILaserWavelength INTEGER
  sfbrm100DMITemperature INTEGER
  sfbrm100DMITempAlarm INTEGER
  sfbrm100DMITxBiasCurrent INTEGER
  sfbrm100DMITxBiasAlarm INTEGER
  sfbrm100DMITxPowerLevel INTEGER
  sfbrm100DMITxPowerAlarm INTEGER
  sfbrm100DMIRxPowerLevel INTEGER
  sfbrm100DMIRxPowerAlarm INTEGER

Sfbrm100PortL2CPEntry  
SEQUENCE    
  sfbrm100PortL2CPLocIndex INTEGER
  sfbrm100PortL2CPRmtIndex INTEGER
  sfbrm100STPProtocolsFwd INTEGER
  sfbrm100SlowProtocolsFwd INTEGER
  sfbrm100PortAuthProtocolFwd INTEGER
  sfbrm100ELMIProtocolFwd INTEGER
  sfbrm100LLDPProtocolFwd INTEGER
  sfbrm100BridgeMgmtProtocolsFwd INTEGER
  sfbrm100GARPBlockProtocolsFwd INTEGER
  sfbrm100BridgeBlkOtherMulticastsFwd INTEGER

Sfbrm100FwdDBEntry  
SEQUENCE    
  sfbrm100FwdLocPortIndex INTEGER
  sfbrm100FwdDBNum INTEGER
  sfbrm100FwdMacAddress PhysAddress
  sfbrm100FwdConnPort INTEGER
  sfbrm100FwdPriority INTEGER
  sfbrm100FwdEntryType INTEGER
  sfbrm100FwdEntryStatus INTEGER

Sfbrm100VlanEntry  
SEQUENCE    
  sfbrm100VlanLocPortIndex INTEGER
  sfbrm100VlanDBNum INTEGER
  sfbrm100VlanVID INTEGER
  sfbrm100VlanVIDPriOverride INTEGER
  sfbrm100VlanVIDPriority INTEGER
  sfbrm100VlanMemTagPort1 INTEGER
  sfbrm100VlanMemTagPort2 INTEGER
  sfbrm100VlanMemTagPort3 INTEGER
  sfbrm100VlanMemTagPort4 INTEGER
  sfbrm100VlanMemTagPort5 INTEGER
  sfbrm100VlanMemTagPort6 INTEGER
  sfbrm100VlanMemTagPort7 INTEGER
  sfbrm100VlanMemTagPort8 INTEGER
  sfbrm100VlanMemTagPort9 INTEGER
  sfbrm100VlanMemTagPort10 INTEGER
  sfbrm100VlanEntryStatus INTEGER

Defined Values

transition 1.3.6.1.4.1.868
OBJECT IDENTIFIER    

productId 1.3.6.1.4.1.868.1
OBJECT IDENTIFIER    

rptrProdsId 1.3.6.1.4.1.868.1.1
OBJECT IDENTIFIER    

rptrStackMId 1.3.6.1.4.1.868.1.1.1
OBJECT IDENTIFIER    

rptrSPSId 1.3.6.1.4.1.868.1.1.2
OBJECT IDENTIFIER    

ringProdsId 1.3.6.1.4.1.868.1.2
OBJECT IDENTIFIER    

ringStackTRId 1.3.6.1.4.1.868.1.2.1
OBJECT IDENTIFIER    

brdgProdsId 1.3.6.1.4.1.868.1.3
OBJECT IDENTIFIER    

brdgSwitchMId 1.3.6.1.4.1.868.1.3.1
OBJECT IDENTIFIER    

brdgFBRMId 1.3.6.1.4.1.868.1.3.2
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.868.2
OBJECT IDENTIFIER    

rptrSMVer1Id 1.3.6.1.4.1.868.1.1.1.1
OBJECT IDENTIFIER    

rptrSMVer2Id 1.3.6.1.4.1.868.1.1.1.2
OBJECT IDENTIFIER    

rptrSM08TId 1.3.6.1.4.1.868.1.1.1.3
OBJECT IDENTIFIER    

rptrSM08TSId 1.3.6.1.4.1.868.1.1.1.4
OBJECT IDENTIFIER    

rptrSM06FId 1.3.6.1.4.1.868.1.1.1.5
OBJECT IDENTIFIER    

rptrSM06FSId 1.3.6.1.4.1.868.1.1.1.6
OBJECT IDENTIFIER    

rptrSM8T0Id 1.3.6.1.4.1.868.1.1.1.7
OBJECT IDENTIFIER    

rptrSM8TS0Id 1.3.6.1.4.1.868.1.1.1.8
OBJECT IDENTIFIER    

rptrSM6F0Id 1.3.6.1.4.1.868.1.1.1.9
OBJECT IDENTIFIER    

rptrSM6FS0Id 1.3.6.1.4.1.868.1.1.1.10
OBJECT IDENTIFIER    

rptrSM8T6FId 1.3.6.1.4.1.868.1.1.1.11
OBJECT IDENTIFIER    

rptrSM8TS6FId 1.3.6.1.4.1.868.1.1.1.12
OBJECT IDENTIFIER    

rptrSM8T6FSId 1.3.6.1.4.1.868.1.1.1.13
OBJECT IDENTIFIER    

rptrSM8TS6FSId 1.3.6.1.4.1.868.1.1.1.14
OBJECT IDENTIFIER    

rptrSM6F8TId 1.3.6.1.4.1.868.1.1.1.15
OBJECT IDENTIFIER    

rptrSM6FS8TId 1.3.6.1.4.1.868.1.1.1.16
OBJECT IDENTIFIER    

rptrSM6F8TSId 1.3.6.1.4.1.868.1.1.1.17
OBJECT IDENTIFIER    

rptrSM6FS8TSId 1.3.6.1.4.1.868.1.1.1.18
OBJECT IDENTIFIER    

rptrSM8T8TId 1.3.6.1.4.1.868.1.1.1.19
OBJECT IDENTIFIER    

rptrSM8TS8TId 1.3.6.1.4.1.868.1.1.1.20
OBJECT IDENTIFIER    

rptrSM8T8TSId 1.3.6.1.4.1.868.1.1.1.21
OBJECT IDENTIFIER    

rptrSM8TS8TSId 1.3.6.1.4.1.868.1.1.1.22
OBJECT IDENTIFIER    

rptrSM6F6FId 1.3.6.1.4.1.868.1.1.1.23
OBJECT IDENTIFIER    

rptrSM6FS6FId 1.3.6.1.4.1.868.1.1.1.24
OBJECT IDENTIFIER    

rptrSM6F6FSId 1.3.6.1.4.1.868.1.1.1.25
OBJECT IDENTIFIER    

rptrSM6FS6FSId 1.3.6.1.4.1.868.1.1.1.26
OBJECT IDENTIFIER    

rptrSM24TId 1.3.6.1.4.1.868.1.1.1.27
OBJECT IDENTIFIER    

rptrSM16TId 1.3.6.1.4.1.868.1.1.1.28
OBJECT IDENTIFIER    

rptrSM14FId 1.3.6.1.4.1.868.1.1.1.29
OBJECT IDENTIFIER    

rptrSM12FId 1.3.6.1.4.1.868.1.1.1.30
OBJECT IDENTIFIER    

rptrSM6FId 1.3.6.1.4.1.868.1.1.1.31
OBJECT IDENTIFIER    

rptrSM0Id 1.3.6.1.4.1.868.1.1.1.32
OBJECT IDENTIFIER    

rptrSPSVer1Id 1.3.6.1.4.1.868.1.1.2.1
OBJECT IDENTIFIER    

rptrESPS24Id 1.3.6.1.4.1.868.1.1.2.2
OBJECT IDENTIFIER    

rptrESPS24SId 1.3.6.1.4.1.868.1.1.2.3
OBJECT IDENTIFIER    

ringTRVer1Id 1.3.6.1.4.1.868.1.2.1.1
OBJECT IDENTIFIER    

ringTRVer2Id 1.3.6.1.4.1.868.1.2.1.2
OBJECT IDENTIFIER    

ringTR0Id 1.3.6.1.4.1.868.1.2.1.3
OBJECT IDENTIFIER    

ringTR16TId 1.3.6.1.4.1.868.1.2.1.4
OBJECT IDENTIFIER    

brdgSWVer1Id 1.3.6.1.4.1.868.1.3.1.1
OBJECT IDENTIFIER    

repeater 1.3.6.1.4.1.868.2.1
OBJECT IDENTIFIER    

tnStackM 1.3.6.1.4.1.868.2.1.1
OBJECT IDENTIFIER    

tnSMCommon 1.3.6.1.4.1.868.2.1.1.1
OBJECT IDENTIFIER    

tnSMVer1 1.3.6.1.4.1.868.2.1.1.2
OBJECT IDENTIFIER    

tnSMVer2 1.3.6.1.4.1.868.2.1.1.3
OBJECT IDENTIFIER    

sps 1.3.6.1.4.1.868.2.1.2
OBJECT IDENTIFIER    

spsCommon 1.3.6.1.4.1.868.2.1.2.1
OBJECT IDENTIFIER    

spsVer1 1.3.6.1.4.1.868.2.1.2.2
OBJECT IDENTIFIER    

ring 1.3.6.1.4.1.868.2.2
OBJECT IDENTIFIER    

tnStackTR 1.3.6.1.4.1.868.2.2.1
OBJECT IDENTIFIER    

tnTRCommon 1.3.6.1.4.1.868.2.2.1.1
OBJECT IDENTIFIER    

tnTRVer1 1.3.6.1.4.1.868.2.2.1.2
OBJECT IDENTIFIER    

tnTRVer2 1.3.6.1.4.1.868.2.2.1.3
OBJECT IDENTIFIER    

bridge 1.3.6.1.4.1.868.2.3
OBJECT IDENTIFIER    

sfbrm10x100 1.3.6.1.4.1.868.2.3.1
OBJECT IDENTIFIER    

sfbrmSystem 1.3.6.1.4.1.868.2.3.1.1
OBJECT IDENTIFIER    

sfbrmSwitch 1.3.6.1.4.1.868.2.3.1.2
OBJECT IDENTIFIER    

sfbrmPort 1.3.6.1.4.1.868.2.3.1.3
OBJECT IDENTIFIER    

sfbrmAddrDB 1.3.6.1.4.1.868.2.3.1.4
OBJECT IDENTIFIER    

tnSMComHwReset 1.3.6.1.4.1.868.2.1.1.1.1
Perform a hardware reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

tnSMComMgmtHwRev 1.3.6.1.4.1.868.2.1.1.1.2
The management h/w board revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnSMComDiagSwRev 1.3.6.1.4.1.868.2.1.1.1.3
The diagnostic s/w code revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnSMComMgmtSwRev 1.3.6.1.4.1.868.2.1.1.1.4
The downloadable management s/w code revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnSMComIpAddr 1.3.6.1.4.1.868.2.1.1.1.5
The IP address to which this entry's addressing information pertains.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

tnSMComNetMask 1.3.6.1.4.1.868.2.1.1.1.6
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

spsReset 1.3.6.1.4.1.868.2.1.2.1.1
Setting this object to reset(2) causes a reset of the hardware. Setting this object to noReset(1) has no effect. The agent will always return the value noReset(1) when this object is read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

spsConfig 1.3.6.1.4.1.868.2.1.2.1.2
The hardware configuration information. The type and size of ROM, RAM, and DRAM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

spsBootpEnable 1.3.6.1.4.1.868.2.1.2.1.3
If this object is set to enabled(1) the unit will use the Bootstrap Protocol (BOOTP) on power-up or reset to obtain its IP configuration parameters. If this object is set to disabled(2) the unit will not use BOOTP. It will use values stored in non-volatile storage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsBootpServer 1.3.6.1.4.1.868.2.1.2.1.4
This object specifies the IP address of the BOOTP server the client wishes to respond; forcing the boot to occur from a specific host. If the IP address of the BOOTP server is unknown this object should be set to be the 'broadcast address' 255.255.255.255. The value of this object is not updated by the system when it determines the IP address of the BOOTP server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

spsBootpFilename 1.3.6.1.4.1.868.2.1.2.1.5
The 'generic' filename to be booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

spsDefaultGateway 1.3.6.1.4.1.868.2.1.2.1.6
This object specifies the IP address of the default gateway. This object is the same as ipRouteDest for the default route. It is placed here as a single object for convenience.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

spsMgmtSegment 1.3.6.1.4.1.868.2.1.2.1.7
Indicates the segment the management interface is on. The value is between 1 and spsMaxSegment. The agent should not allow the NMU to be placed on a segment which has no ports assigned to it, as this would prevent communication with the NMU.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

spsIpAddrTable 1.3.6.1.4.1.868.2.1.2.1.8
The table of addressing information relevant to this entity's IP addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsIpAddrEntry

spsIpAddrEntry 1.3.6.1.4.1.868.2.1.2.1.8.1
The addressing information relevant to this entity's IP addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsIpAddrEntry  

spsIpIfIndex 1.3.6.1.4.1.868.2.1.2.1.8.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same as identified by the same value of ifIndex (and also ipAdEntIfIndex).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsIpAddr 1.3.6.1.4.1.868.2.1.2.1.8.1.2
The IP address to which this entry's addressing information pertains. The IP address value for this entry is the same value as specified by ipAdEntAddr. This entry differs from ipAdEntAddr, in that it has read-write access, which allows the IP address to be specified using SNMP. The unit must be reset for the new IP address to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

spsIpNetMask 1.3.6.1.4.1.868.2.1.2.1.8.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. The subnet mask value for this entry is the same value as specified by ipAdEntNetMask. This entry differs from ipAdEntNetMask in that is has read- write access, which allows the subnet mask to be specified using SNMP. The unit must be reset for the new subnet mask to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

spsTrapTable 1.3.6.1.4.1.868.2.1.2.1.9
A list of trap destinations and community names. When generating a trap, each destination in this list is sent the trap using the associated community name.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsTrapEntry

spsTrapEntry 1.3.6.1.4.1.868.2.1.2.1.9.1
An entry in the spsTrapTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsTrapEntry  

spsTrapIndex 1.3.6.1.4.1.868.2.1.2.1.9.1.1
The index value which uniquely identifies the SNMP trap destination and community name pairing to which this entry is applicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsTrapDestination 1.3.6.1.4.1.868.2.1.2.1.9.1.2
This object specifies the destination address of the Trap-PDU.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

spsTrapCommunity 1.3.6.1.4.1.868.2.1.2.1.9.1.3
The community name used when generating traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

spsMaxSegment 1.3.6.1.4.1.868.2.1.2.2.1
The maximum number of segments supported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsPasswdReset 1.3.6.1.4.1.868.2.1.2.2.2
If this object is set to reset(2) resets the joystick password to a known value. Setting this value to noReset(1) has no effect. The agent will always return the value noReset(1) when this object is read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

spsExternalPowerSupply 1.3.6.1.4.1.868.2.1.2.2.3
This object indicates the status of the internal power supply. A value of present(1) indicates the power supply is present and able to provide power. A value of notPresent(2) indicates the power supply is unable to provide power or is not present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notPresent(2)  

spsDisplayString 1.3.6.1.4.1.868.2.1.2.2.4
Setting this object changes the contents of the display.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(8)  

spsRptrGroupTable 1.3.6.1.4.1.868.2.1.2.2.5
Table of descriptive and status information about the repeater groups (Units).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsRptrGroupEntry

spsRptrGroupEntry 1.3.6.1.4.1.868.2.1.2.2.5.1
An entry in the table, containing information about a single repeater group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsRptrGroupEntry  

spsRptrGroupIndex 1.3.6.1.4.1.868.2.1.2.2.5.1.1
This object identifies the group containing the port for which this entry contains information. The group identified by a particular value of this index is the same group as identified by the same value of rptrPortGroupIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsRptrGroupUnitId 1.3.6.1.4.1.868.2.1.2.2.5.1.2
A unique string which identifies this unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

spsRptrGroupInternalPowerSupply 1.3.6.1.4.1.868.2.1.2.2.5.1.3
This object indicates the status of the internal power supply. A value of present(1) indicates the power supply is present and able to provide power. A value of notPresent(2) indicates the power supply is unable to provide power or is not present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notPresent(2)  

spsRptrPortTable 1.3.6.1.4.1.868.2.1.2.2.6
Table of descriptive and status information about the ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsRptrPortEntry

spsRptrPortEntry 1.3.6.1.4.1.868.2.1.2.2.6.1
An entry in the table, containing information about a single port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsRptrPortEntry  

spsRptrPortGroupIndex 1.3.6.1.4.1.868.2.1.2.2.6.1.1
This object identifies the group containing the port for which this entry contains information. The group identified by a particular value of this index is the same group as identified by the same value of rptrPortGroupIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsRptrPortIndex 1.3.6.1.4.1.868.2.1.2.2.6.1.2
This object identifies the port within the group for which this entry contains information. The port identified by a particular value of this index is the same port as identified by the same value of rptrPortIndex. This value can never be greater than rptrGroupPortCapacity for the associated group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsRptrPortSegment 1.3.6.1.4.1.868.2.1.2.2.6.1.3
The segment number to which this port belongs. This value is never greater than spsMaxSegment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

spsRptrPortSrcAddr 1.3.6.1.4.1.868.2.1.2.2.6.1.4
When spsRptrPortEavesdropping or spsRptrPortIntrusion are enabled this object contains the authorized source address, otherwise this object contains the source address field from the last correctly received frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

spsRptrPortEavesdropping 1.3.6.1.4.1.868.2.1.2.2.6.1.5
Eavesdropping protection safeguards the network from promiscuous mode stations receiving intelligible data from the network. Setting this object to enabled(1) enables eavesdropping protection. Eavesdropping protection causes the currently transmitted frame to be jammed if the destination address field does not match spsRptrPortSrcAddr . Setting this object to disabled(2) disables eavesdropping protection and the frame is not jammed. All broadcast and multicast packets are repeated to all ports on the same segment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsRptrPortIntrusion 1.3.6.1.4.1.868.2.1.2.2.6.1.6
Automatic intrusion protection prevents unauthorized users from gaining access to the network. Conceptually, the source address field of the received packet is compared to the authorized source address. If the addresses differ, the user is classified as an intruder and the data going to the backplane is jammed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsRptrPortCollisionLimit 1.3.6.1.4.1.868.2.1.2.2.6.1.7
Selects the consecutive collision count that will cause port partitioning. Valid values are 31, 63, 127, and 255.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER collision-limit-31(31), collision-limit-63(63), collision-limit-127(127), collision-limit-155(255)  

spsRptrPortEnableIntruderDetectTrap 1.3.6.1.4.1.868.2.1.2.2.6.1.8
Indicates whether the SNMP agent process is permitted to generate intruderDetection traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsRptrPortDisableIntruder 1.3.6.1.4.1.868.2.1.2.2.6.1.9
Indicates whether the port is disabled when an intruder is detected. Disabling a port in this manner is the same as setting the rptrPortAdminStatus object for this port to disabled(2). The security mechanism will not automatically enable a port.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsSerialPortTable 1.3.6.1.4.1.868.2.1.2.2.7
The table of RS-232 serial ports. Table only contains information not found in RFC-1316 and RFC-1317 Definitions of Managed Objects for RS-232-like Hardware Devices.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsSerialPortEntry

spsSerialPortEntry 1.3.6.1.4.1.868.2.1.2.2.7.1
Table entry for a specific RS-232 serial port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsSerialPortEntry  

spsSerialPortIndex 1.3.6.1.4.1.868.2.1.2.2.7.1.1
A unique value for each port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

spsSerialPortModemControl 1.3.6.1.4.1.868.2.1.2.2.7.1.2
Setting this object to enabled(1) enables the monitoring and control of modem control lines by the serial port. Setting this object to disabled(2) disables the monitoring and control of modem control lines by the serial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

spsMonitorSegmentTable 1.3.6.1.4.1.868.2.1.2.2.8
Table of performance and error statistics for the segments.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpsMonitorSegmentEntry

spsMonitorSegmentEntry 1.3.6.1.4.1.868.2.1.2.2.8.1
An entry in the table, containing total performance and error statistics for a single segment. Regular retrieval of the information in this table provides a means of tracking the performance and health of the networked devices attached to this segment's ports. The counters in this table are redundant in the sense that they are the summations of information already available through other objects. However, these sums provide a considerable optimization of network management traffic over the otherwise necessary retrieval of the individual counters included in each sum.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SpsMonitorSegmentEntry  

spsMonitorSegmentIndex 1.3.6.1.4.1.868.2.1.2.2.8.1.1
This object identifies the group within the repeater for which this entry contains information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1024  

spsMonitorSegmentTotalFrames 1.3.6.1.4.1.868.2.1.2.2.8.1.2
The total number of frames of valid frame length that have been received on the ports in this group and for which the FCSError and CollisionEvent signals were not asserted. This counter is the summation of the values of the rptrMonitorPortReadableFrames counters for all of the ports in the segment. This statistic provides one of the parameters necessary for obtaining the packet error rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

spsMonitorSegmentTotalOctets 1.3.6.1.4.1.868.2.1.2.2.8.1.3
The total number of octets contained in the valid frames that have been received on the ports in this segment. This counter is the summation of the values of the rptrMonitorPortReadableOctets counters for all of the ports in the segment. This statistic provides an indicator of the total data transferred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

spsMonitorSegmentTotalErrors 1.3.6.1.4.1.868.2.1.2.2.8.1.4
The total number of errors which have occurred on all of the ports in this segment. This counter is the summation of the values of the rptrMonitorPortTotalErrors counters for all of the ports in the segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRComHwReset 1.3.6.1.4.1.868.2.2.1.1.1
Perform a hardware reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

tnTRComMgmtHwRev 1.3.6.1.4.1.868.2.2.1.1.2
The management h/w board revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnTRComDiagSwRev 1.3.6.1.4.1.868.2.2.1.1.3
The diagnostic s/w code revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnTRComMgmtSwRev 1.3.6.1.4.1.868.2.2.1.1.4
The downloadable management s/w code revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

tnTRComIpAddr 1.3.6.1.4.1.868.2.2.1.1.5
The IP address to which this entry's addressing information pertains.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

tnTRComNetMask 1.3.6.1.4.1.868.2.2.1.1.6
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

tnTRComIfaceCapacity 1.3.6.1.4.1.868.2.2.1.1.7
The total number of interfaces found in the stack.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1Commands 1.3.6.1.4.1.868.2.2.1.2.1
When this object is set to the value of open(2), the station should go into the open state. The progress and success of the open is given by the values of the objects dot5RingState and dot5RingOpenStatus. When this object is set to the value of reset(3), then the station should do a reset. On a reset, all MIB counters should retain their values, if possible. Other side affects are dependent on the hardware chip set. When this object is set to the value of close(4), the station should go into the stopped state by removing itself from the ring. Setting this object to a value of no-op(1) has no effect. When read, this object always has a value of no-op(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-op(1), open(2), reset(3), close(4)  

tnTRV1RingStatus 1.3.6.1.4.1.868.2.2.1.2.2
The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to the ring. Before an open is completed, this object has the value for the 'no status' condition. The dot5RingState and dot5RingOpenStatus objects provide for debugging problems when the station can not even enter the ring. The object's value is a sum of values, one for each currently applicable condition. The following values are defined for various conditions: 0 = No Problems detected 32 = Ring Recovery 64 = Single Station 256 = Remove Received 512 = reserved 1024 = Auto-Removal Error 2048 = Lobe Wire Fault 4096 = Transmit Beacon 8192 = Soft Error 16384 = Hard Error 32768 = Signal Loss 131072 = no status, open not completed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1RingState 1.3.6.1.4.1.868.2.2.1.2.3
The current interface state with respect to entering or leaving the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER opened(1), closed(2), opening(3), closing(4), openFailure(5), ringFailure(6)  

tnTRV1RingOpenStatus 1.3.6.1.4.1.868.2.2.1.2.4
This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noOpen(1), badParam(2), lobeFailed(3), signalLoss(4), insertionTimeout(5), ringFailed(6), beaconing(7), duplicateMAC(8), requestFailed(9), removeReceived(10), open(11)  

tnTRV1RingSpeed 1.3.6.1.4.1.868.2.2.1.2.5
The ring's bandwidth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), oneMegabit(2), fourMegabit(3), sixteenMegabit(4)  

tnTRV1UpStream 1.3.6.1.4.1.868.2.2.1.2.6
The MAC-address of the up stream neighbor station in the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

tnTRV1ActMonParticipate 1.3.6.1.4.1.868.2.2.1.2.7
If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. Setting this object might not have an effect until the next time the interface is opened.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

tnTRV1Functional 1.3.6.1.4.1.868.2.2.1.2.8
The bit mask of all Token Ring functional addresses for which this interface will accept frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

tnTRV1StatsLineErrors 1.3.6.1.4.1.868.2.2.1.2.9
This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsBurstErrors 1.3.6.1.4.1.868.2.2.1.2.10
This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsACErrors 1.3.6.1.4.1.868.2.2.1.2.11
This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsAbortTransErrors 1.3.6.1.4.1.868.2.2.1.2.12
This counter is incremented when a station transmits an abort delimiter while transmitting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsInternalErrors 1.3.6.1.4.1.868.2.2.1.2.13
This counter is incremented when a station recognizes an internal error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsLostFrameErrors 1.3.6.1.4.1.868.2.2.1.2.14
This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TRR timer goes off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsReceiveCongestions 1.3.6.1.4.1.868.2.2.1.2.15
This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsFrameCopiedErrors 1.3.6.1.4.1.868.2.2.1.2.16
This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsTokenErrors 1.3.6.1.4.1.868.2.2.1.2.17
This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsSoftErrors 1.3.6.1.4.1.868.2.2.1.2.18
The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Soft Errors are those which are recoverable by the MAC layer protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsHardErrors 1.3.6.1.4.1.868.2.2.1.2.19
The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon MAC frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsSignalLoss 1.3.6.1.4.1.868.2.2.1.2.20
The number of times this interface has detected the loss of signal condition from the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsTransmitBeacons 1.3.6.1.4.1.868.2.2.1.2.21
The number of times this interface has transmitted a beacon frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsRecoverys 1.3.6.1.4.1.868.2.2.1.2.22
The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This counter signifies the number of times the ring has been purged and is being recovered back into a normal operating state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsLobeWires 1.3.6.1.4.1.868.2.2.1.2.23
The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and dot5RingState will signify this condition.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsRemoves 1.3.6.1.4.1.868.2.2.1.2.24
The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state and dot5RingState will signify this condition.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsSingles 1.3.6.1.4.1.868.2.2.1.2.25
The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1StatsFreqErrors 1.3.6.1.4.1.868.2.2.1.2.26
The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that specified by the IEEE 802.5 standard, see chapter 7 in [10].
Status: optional Access: read-only
OBJECT-TYPE    
  Counter  

tnTRV1TimerReturnRepeat 1.3.6.1.4.1.868.2.2.1.2.27
The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring latency. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerHolding 1.3.6.1.4.1.868.2.2.1.2.28
Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerQueuePDU 1.3.6.1.4.1.868.2.2.1.2.29
The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds. Implementors are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerValidTransmit 1.3.6.1.4.1.868.2.2.1.2.30
The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerNoToken 1.3.6.1.4.1.868.2.2.1.2.31
The time-out value used to recover from various-related error situations [9]. If N is the maximum number of stations on the ring, the value of this timer is normally: dot5TimerReturnRepeat + N * dot5TimerHolding. Implementors are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerActiveMon 1.3.6.1.4.1.868.2.2.1.2.32
The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds. Implementors are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerStandbyMon 1.3.6.1.4.1.868.2.2.1.2.33
The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of 100 micro-seconds. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerErrorReport 1.3.6.1.4.1.868.2.2.1.2.34
The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds. Implementors are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerBeaconTransmit 1.3.6.1.4.1.868.2.2.1.2.35
The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 100 micro-seconds. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnTRV1TimerBeaconReceive 1.3.6.1.4.1.868.2.2.1.2.36
The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 100 micro-seconds. Implementers are encouraged to provide read-write access to this object if that is possible/useful in their system, but giving due consideration to the dangers of write-able timers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tnIntruderDetect 1
The tnIntruderDetect trap conveys information related to the automatic intrusion detection of the SPS2000. This trap is sent when an intruder is detected.
TRAP-TYPE    

sfbrm100SystemTable 1.3.6.1.4.1.868.2.3.1.1.1
System Information and Configuration table for the xFBRM/xBFFG 802.3ah Managed device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100SystemEntry

sfbrm100SystemEntry 1.3.6.1.4.1.868.2.3.1.1.1.1
Status and configuration entries for a xFBRM/xBFFG device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100SystemEntry  

sfbrm100SysLocPortIndex 1.3.6.1.4.1.868.2.3.1.1.1.1.1
The local port index of the port to which the peer is connected. The local device has an index of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysSecIndex 1.3.6.1.4.1.868.2.3.1.1.1.1.2
Secondary index for the table. It is always 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysGrpString 1.3.6.1.4.1.868.2.3.1.1.1.1.3
Group membership string. See http://www.transition.com/pshelp/configmgmt1.html
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

sfbrm100SysMRevision 1.3.6.1.4.1.868.2.3.1.1.1.1.4
The marketing revision of this device. See http://www.transition.com/pshelp/mrevision.html
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysCfgMatch 1.3.6.1.4.1.868.2.3.1.1.1.1.5
See http://www.transition.com/pshelp/configmgmt1.html
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

sfbrm100SysBootLoaderRevision 1.3.6.1.4.1.868.2.3.1.1.1.1.6
The bootloader revision level for this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sfbrm100SysFirmwareRevision 1.3.6.1.4.1.868.2.3.1.1.1.1.7
The firmware revision level for this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sfbrm100SysSerialNumber 1.3.6.1.4.1.868.2.3.1.1.1.1.8
The serial number of this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysBIAddress 1.3.6.1.4.1.868.2.3.1.1.1.1.9
The serial number (BIA) of the cabinet in which the device is installed. If it is a stand-alone this is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysSlotIndex 1.3.6.1.4.1.868.2.3.1.1.1.1.10
The Slot number if installed in a chassis. Zero if stand-alone.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysNumPorts 1.3.6.1.4.1.868.2.3.1.1.1.1.11
The Number of ports on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysMACAddress 1.3.6.1.4.1.868.2.3.1.1.1.1.12
The MAC address used in MGMT frames and IP Packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

sfbrm100SystemReset 1.3.6.1.4.1.868.2.3.1.1.1.1.13
Set this to reset(1) to cause the system to reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), doNothing(2)  

sfbrm100SysIPaddress 1.3.6.1.4.1.868.2.3.1.1.1.1.14
The IPV4 address of the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysSubnetMask 1.3.6.1.4.1.868.2.3.1.1.1.1.15
The subnet mask associated with the IP address of the device. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysDefGateway 1.3.6.1.4.1.868.2.3.1.1.1.1.16
The default gateway for the device
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysSNMPTrapMgr 1.3.6.1.4.1.868.2.3.1.1.1.1.17
The IPV4 address of the SNMP trap manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysRadiusAuth 1.3.6.1.4.1.868.2.3.1.1.1.1.18
RADIUS authentication can be enabled or disabled using this variable. RADIUS Authentication is used for management access only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sfbrm100SysRadiusServerAddr 1.3.6.1.4.1.868.2.3.1.1.1.1.19
The IPV4 address of the Radius Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysRadiusSecret 1.3.6.1.4.1.868.2.3.1.1.1.1.20
The shared secret between the device and RADIUS server. A read returns 'xxx' for security.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sfbrm100SysRadiusRetry 1.3.6.1.4.1.868.2.3.1.1.1.1.21
The number of times the device would try to contact the RADIUS server, when there is any communication problem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SysRadiusTimeout 1.3.6.1.4.1.868.2.3.1.1.1.1.22
The number of seconds the device would wait for the server response before it times out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SysDHCPEnable 1.3.6.1.4.1.868.2.3.1.1.1.1.23
Enable/Disable DHCP. A reset of the system is needed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysSerialAccess 1.3.6.1.4.1.868.2.3.1.1.1.1.24
Enable/Disable access to USB Port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysTLPT 1.3.6.1.4.1.868.2.3.1.1.1.1.25
Enable/disable Transparent Link Pass through. If the Peer's remote link goes down, the link down is passed on to the other end while the OAM channel is still active.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysTFTPServerAddr 1.3.6.1.4.1.868.2.3.1.1.1.1.26
The IPV4 address of the TFTP Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfbrm100SysTFTPfilename 1.3.6.1.4.1.868.2.3.1.1.1.1.27
The Firmware file to be downloaded from the TFTP Server for upgrading.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sfbrm100SysTFTPCmd 1.3.6.1.4.1.868.2.3.1.1.1.1.28
To initiate a TFTP upgrading, set the value to perform(1), the systems resets and the bootloader is invoked to perform the upgrade.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER perform(1), donothing(2), notApplicable(3)  

sfbrm100SysTFTPServerIgnore 1.3.6.1.4.1.868.2.3.1.1.1.1.29
In some configuration, when the device uses DHCP to get its IP address, it also receives the tftpserver address for upgrading. When this variable is enabled the tftpserver address got from DHCP is ignored. This is valid only when DHCP is enabled, else notApplicable(3) is returned. It is disabled by default.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100SysMgmtVlanId 1.3.6.1.4.1.868.2.3.1.1.1.1.30
VLAN Id for the management frames. This is valid only when vlan is enabled. This creates a secure channel for all management traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysSNMPAccess 1.3.6.1.4.1.868.2.3.1.1.1.1.31
The SNMP access to the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysIPAccess 1.3.6.1.4.1.868.2.3.1.1.1.1.32
IP management access to the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysLastGaspPdu 1.3.6.1.4.1.868.2.3.1.1.1.1.33
This mib variable is used to choose the type of PDU to be generated on the last gasp event.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER snmpTrap(1), oamDyingGaspPdu(2)  

sfbrm100SysLastGaspPort 1.3.6.1.4.1.868.2.3.1.1.1.1.34
When there are multiple OAM enabled ports, this variable decides which port to send the Dying gasp OAM PDU. The default is Port 2. This variable is valid only when sfbrm100SysLastGaspPdu is set to oamDyingGaspPdu(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SysLocalLPT 1.3.6.1.4.1.868.2.3.1.1.1.1.35
When the monitored port (sfbrm100SysLPTPort)link goes down, the other port is brought down when this is enabled. This is also named as Selective Link Pass Through.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysLPTPort 1.3.6.1.4.1.868.2.3.1.1.1.1.36
This determines the port, on which the Transparent Link pass through and the Selective/local Link pass through will be active. Any link change on this port activates the TLPT and LocalLPT. This is should be the port with active OAM session.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SysAutoUpgrade 1.3.6.1.4.1.868.2.3.1.1.1.1.37
When enabled, auto upgrade of this device can be done by its peer. By default this is 'enabled(1)'. When disabled, the peer should do a Force upgrade in order to override this variable. Auto upgrade feature affects when this device is in 'passive' mode during the OAM session and is running a different firmware than its peer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SysFormFactorSlot 1.3.6.1.4.1.868.2.3.1.1.1.1.38
This read-only variable gives the number of slots in a chassis this unit occupies if its a chassis card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysFormFactorPort 1.3.6.1.4.1.868.2.3.1.1.1.1.39
This read-only variables gives type of ports present on this board. The values and description for each board : 1 - xFBRM 10/100BaseT to 100BaseFx 2 - xFBRM 100BaseFx to 1000BaseX 3 - xBFFG 1000BaseX to 1000BaseX 4 - xBFFG 10/100/1000BaseT to 1000BaseX 5 - xFBRM 10/100BaseT to 2x100BaseFx 6 - xBFFG 10/100/1000BaseT to 2x1000BaseX
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SysOAMPort 1.3.6.1.4.1.868.2.3.1.1.1.1.40
When only one OAM session is allowed, this determines the port that will be used for sending and receiving OAM messages. This also restricts the number of manageable remotes to be 1. All other ports have OAM admin state will be disabled, this will affect the current OAM sessions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwTable 1.3.6.1.4.1.868.2.3.1.2.1
Switch Status and configuration table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100SwEntry

sfbrm100SwEntry 1.3.6.1.4.1.868.2.3.1.2.1.1
Status and configuration entries for switch setting.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100SwEntry  

sfbrm100SwPortIndex 1.3.6.1.4.1.868.2.3.1.2.1.1.1
The Local Port Index of the local port to which the peer is connected. The local device has the port index of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SwSecIndex 1.3.6.1.4.1.868.2.3.1.2.1.1.2
Secondary index for the table. It is always 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SwATUAgeTimeout 1.3.6.1.4.1.868.2.3.1.2.1.1.3
The ATU ageing time in seconds. This indicates the time that each ATU entry remains valid in the database before being purged. The minimum aging time is 15 seconds and maximum is 64 minutes. A ageing time time of zero disables ageing. i.e All addresses remain in the database, they are never purged. The aging time should be in 15 sec increments.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIngressMonPort 1.3.6.1.4.1.868.2.3.1.2.1.1.4
The Ingress monitor port. Frames that are targeted towards an Ingress monitor port go out this port. Not-applicable for a 2-Port device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwEgressMonPort 1.3.6.1.4.1.868.2.3.1.2.1.1.5
The egress monitor port. Frames that are targeted towards an Egress monitor port go out this port. Not-applicable for a 2-Port device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwFactoryDefaults 1.3.6.1.4.1.868.2.3.1.2.1.1.6
Reset the switch to factory default settings. A read always returns a notApplicable(2) value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), notApplicable(2)  

sfbrm100SwResetCounters 1.3.6.1.4.1.868.2.3.1.2.1.1.7
Resets all port counters. A read always returns a notApplicable(2) value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), notApplicable(2)  

sfbrm100SwHistMode 1.3.6.1.4.1.868.2.3.1.2.1.1.8
The port histogram counters can be set to : cntRx (1) - count Rx frames only. cntTx (2) - count Tx frames only cntRxTx (3) - count Rx and Tx frames. This affects the histogram counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cntRx(1), cntTx(2), cntRxTx(3)  

sfbrm100SwIEEEPriRemap0 1.3.6.1.4.1.868.2.3.1.2.1.1.9
All Frames with priority 0 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap1 1.3.6.1.4.1.868.2.3.1.2.1.1.10
All Frames with priority 1 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap2 1.3.6.1.4.1.868.2.3.1.2.1.1.11
All Frames with priority 2 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap3 1.3.6.1.4.1.868.2.3.1.2.1.1.12
All Frames with priority 3 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap4 1.3.6.1.4.1.868.2.3.1.2.1.1.13
All Frames with priority 4 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap5 1.3.6.1.4.1.868.2.3.1.2.1.1.14
All Frames with priority 5 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap6 1.3.6.1.4.1.868.2.3.1.2.1.1.15
All Frames with priority 6 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIEEEPriRemap7 1.3.6.1.4.1.868.2.3.1.2.1.1.16
All Frames with priority 7 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwFlushFdb 1.3.6.1.4.1.868.2.3.1.2.1.1.17
Flushes all static entries in the forwarding database. When set to flushAll(1), all the entries in the database are purged. when set to flushNonStatic(2), all non-static entries in the database are flushed. A read always returns doNothing(3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER flushAll(1), flushNonStatic(2), doNothing(3)  

sfbrm100SwFlushVlandb 1.3.6.1.4.1.868.2.3.1.2.1.1.18
Flushes all VLAN entries in the database. When set to flushAll(1), all VLAN entries in the database are purged, and VLAN is disabled automatically. A read always returns doNothing(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER flushAll(1), doNothing(2)  

sfbrm100SwUseDoubleTagData 1.3.6.1.4.1.868.2.3.1.2.1.1.19
When Double tagging is enabled on any of the ports, this mib variable decides if the tag that is removed from Ingress frames should be used or ignored when making switching decision on the frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER use(1), ignore(2)  

sfbrm100SwFiberRedundancy 1.3.6.1.4.1.868.2.3.1.2.1.1.20
This feature is applicable in the xFBRM/xBFFG series which have 2 fiber ports. When set to enabled, the primary and backup fiber ports are assumed to be connected to the same destination. Only one of these paths will be active at any given time, and the configuration settings kept in sync between the ports. When set to disabled, the primary and backup ports are assumed to be connected to different destinations, and lose their special functions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100SwFiberRedundRevert 1.3.6.1.4.1.868.2.3.1.2.1.1.21
This mib variable is applicable only if 'sfbrm100SwFiberRedundancy' is enabled. When there is a failure in the primary and secondary fiber takes over, this determines what happens when primary comes back again. Does the link switch back to primary or the secondary takes over as the primary link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER revert(1), noRevert(2), notApplicable(3)  

sfbrm100SwFbrRedundActivePort 1.3.6.1.4.1.868.2.3.1.2.1.1.22
This mib variable is applicable only if 'sfbrm100SwFiberRedundancy' is enabled. This indicates the current active port that is operational as the primary link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100SwSupressVlanViolations 1.3.6.1.4.1.868.2.3.1.2.1.1.23
This supresses all VLAN database violations and the traps caused by these events.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SwSupressMACViolations 1.3.6.1.4.1.868.2.3.1.2.1.1.24
This supresses all MAC database violations and the traps caused by these events.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100SwIPPrioTable 1.3.6.1.4.1.868.2.3.1.2.2
IP Traffic class table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100SwIPPrioEntry

sfbrm100SwIPPrioEntry 1.3.6.1.4.1.868.2.3.1.2.2.1
Each entry represents the remapped value for each traffic class.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100SwIPPrioEntry  

sfbrm100SwIPPrioPortIndex 1.3.6.1.4.1.868.2.3.1.2.2.1.1
The Local port to which the device is connected. The local device has the port index as zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIPPrioIndex 1.3.6.1.4.1.868.2.3.1.2.2.1.2
The IP traffic class remap table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIPPrioTC 1.3.6.1.4.1.868.2.3.1.2.2.1.3
The IP traffic class value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100SwIPPrioRemap 1.3.6.1.4.1.868.2.3.1.2.2.1.4
The IP traffic class defined by sfbrm100SwIPPrioTC, is given the priority value set in this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pri0(1), pri1(2), pri2(3), pri3(4)  

sfbrm100PortTable 1.3.6.1.4.1.868.2.3.1.3.1
Port attributes status and configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100PortEntry

sfbrm100PortEntry 1.3.6.1.4.1.868.2.3.1.3.1.1
Status and configuration entries for a each port on the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100PortEntry  

sfbrm100PortLocIndex 1.3.6.1.4.1.868.2.3.1.3.1.1.1
Uniquely indentifies each port on the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortRmtIndex 1.3.6.1.4.1.868.2.3.1.3.1.1.2
Uniquely indentifies each port on the peer device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortGrpString 1.3.6.1.4.1.868.2.3.1.3.1.1.3
Description string for each port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

sfbrm100PortConnType 1.3.6.1.4.1.868.2.3.1.3.1.1.4
The actual physical connector on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  CpsConnector  

sfbrm100PortOAMState 1.3.6.1.4.1.868.2.3.1.3.1.1.5
This object is used to provision the default administrative enable/disable of OAM on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortOAMModeCtrl 1.3.6.1.4.1.868.2.3.1.3.1.1.6
This object can be used to provision the OAM mode for this interface. In auto(1) mode , the interface is set to active/passive depending on if the board is in a chassis or stand-alone. The manual(2) mode lets the user choose the OAM mode (active/passive).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

sfbrm100PortRmtLoopback 1.3.6.1.4.1.868.2.3.1.3.1.1.7
Initiates remote loopback, if supported by remote peer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER oamLoopback(1), alternateLoopback(2), disable(3), notSupported(4)  

sfbrm100PortIgnoreLoopback 1.3.6.1.4.1.868.2.3.1.3.1.1.8
If enabled, the device ignores any loopback requests.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ignore(1), process(2)  

sfbrm100PortAdvPause 1.3.6.1.4.1.868.2.3.1.3.1.1.9
Specifies the Pause frame advertisement capability.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noPause(1), symPause(2), asymPauseLp(3), asymPauseCon(4), notApplicable(5)  

sfbrm100PortAdv1000FDX 1.3.6.1.4.1.868.2.3.1.3.1.1.10
This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, full duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is valid only for Gigabit Ports and not valid for fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAdv1000HDX 1.3.6.1.4.1.868.2.3.1.3.1.1.11
This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, half duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is valid only for Gigabit Ports and not valid for fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAdv100FDX 1.3.6.1.4.1.868.2.3.1.3.1.1.12
This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, full duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is not valid on Fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAdv100HDX 1.3.6.1.4.1.868.2.3.1.3.1.1.13
This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is not valid on Fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAdv10FDX 1.3.6.1.4.1.868.2.3.1.3.1.1.14
This configuration setting controls whether or not this port advertises willingness to connect at 10Mbps, full duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is not valid on Fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAdv10HDX 1.3.6.1.4.1.868.2.3.1.3.1.1.15
This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is ignored when autonegotiation is disabled, read-only value notApplicable(3)is returned. This is not valid on Fiber ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAutoneg 1.3.6.1.4.1.868.2.3.1.3.1.1.16
Enable/Disable autonegotiation on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), negotiating(3), resolved(4)  

sfbrm100PortFDuplex 1.3.6.1.4.1.868.2.3.1.3.1.1.17
This is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. This is valid only when autonegotiation is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), notApplicable(3)  

sfbrm100PortFSpeed 1.3.6.1.4.1.868.2.3.1.3.1.1.18
This is a configuration setting that controls the speed; This is valid only when autonegotiation is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mbps10(1), mbps100(2), mbps1000(3), notApplicable(4)  

sfbrm100PortLpPauseAbility 1.3.6.1.4.1.868.2.3.1.3.1.1.19
Link Partner's pause capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noPause(1), symPause(2), asymPauseLp(3), asymPauseCon(4), notApplicable(5)  

sfbrm100PortLpAutonegAbility 1.3.6.1.4.1.868.2.3.1.3.1.1.20
The autonegotiation advertisement mode can be set using the options of this variable. spdAutoDupAuto(1) - Advertise all speed and duplex supported. spd1000DupAuto(2) - Advertise 1000Mbps with duplex as full and half spd100DupAuto(3) - Advertise 100Mbps with duplex as full and half spd10DupAuto(4) - Advertise 10Mbps with duplex as full and half spdAutoDupFull(5) - Advertise all speeds (10, 100, 1000 Mbps) with Full duplex spdAutoDupHalf(6) - Advertise all speeds (10, 100, 1000 Mbps) with Half duplex spd1000DupFull(7) - Advertise 1000Mbps full duplex spd1000DupHalf(8) - Advertise 1000Mbps half duplex spd100DupFull(9) - Advertise 100Mbps full duplex spd100DupHalf(10) - Advertise 100Mbps half duplex spd10DupFull(11) - Advertise 10Mbps full duplex spd10DupHalf(12) - Advertise 10Mbps half duplex Read-only value notApplicable returned when autonegotiation is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER spdAutoDupAuto(1), spd1000DupAuto(2), spd100DupAuto(3), spd10DupAuto(4), spdAutoDupFull(5), spdAutoDupHalf(6), spd1000DupFull(7), spd1000DupHalf(8), spd100DupFull(9), spd100DupHalf(10), spd10DupFull(11), spd10DupHalf(12), notcapable(13)  

sfbrm100PortLinkState 1.3.6.1.4.1.868.2.3.1.3.1.1.21
Link status on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), notApplicable(3)  

sfbrm100PortAutonegState 1.3.6.1.4.1.868.2.3.1.3.1.1.22
The autonegotiation state or if autonegotiation is disabled it returns resolved(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER resolved(1), notResolved(2)  

sfbrm100PortDuplex 1.3.6.1.4.1.868.2.3.1.3.1.1.23
The port's duplex value when autonegotiation is resolved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), notApplicable(3)  

sfbrm100PortSpeed 1.3.6.1.4.1.868.2.3.1.3.1.1.24
The port's duplex value when autonegotiation is resolved
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mbps10(1), mbps100(2), mbps1000(3), notApplicable(4)  

sfbrm100PortFEFI 1.3.6.1.4.1.868.2.3.1.3.1.1.25
Enabled/Disable Far-end Fault detection. Read-only value notApplicable is returned for unsupported Ethernet PHY's.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

sfbrm100PortAutocross 1.3.6.1.4.1.868.2.3.1.3.1.1.26
This is applicable for supporting PHY's. If set to mdi(1) the transmit happens on pair 1 & 2 and receive on 3 & 4. If set to mdiX(2) the transmit happens on 3 & 4 and receive on 1 & 2. If set to autoCross(3) - automatic crossover is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mdi(1), mdiX(2), autoCross(3), notApplicable(4)  

sfbrm100PortLock 1.3.6.1.4.1.868.2.3.1.3.1.1.27
When enabled, it disables the automatic learning of source addresses on this port and drops frames where the SA does not exist in the ATU, and originates a ATU Miss Violation Trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortIgnoreWrongData 1.3.6.1.4.1.868.2.3.1.3.1.1.28
Ignores interrupts caused by reception of frames whose source address is not assigned to this port. When disabled(2), generates a SNMP trap every time a frame is received with SA not belonging to this Port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortIGMPSnoop 1.3.6.1.4.1.868.2.3.1.3.1.1.29
When enabled all IGMP frames are directed to the CPU overriding the Destination address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortDoubleTagging 1.3.6.1.4.1.868.2.3.1.3.1.1.30
When set to enabled, the frames which have 802.3ac tag with IEEE standard ether-type of 0x8100 are examined for tags. On Ingress frames : All untagged frames remain untagged, all single tagged will become untagged and all double tagged frames will be single tagged on ingress. On Egress frames : All frames exit with a extra tag. All untagged frames get a single tag. All single tagged frames gets double tagged.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortUseIPTC 1.3.6.1.4.1.868.2.3.1.3.1.1.31
When enabled, IP priority fields are used for Traffic class of priority data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortUseTagTC 1.3.6.1.4.1.868.2.3.1.3.1.1.32
When enabled, the IEEE 802.1p fields are used for traffic class of priority data if the frame is IEEE 802.1ac tagged.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortUseBothTC 1.3.6.1.4.1.868.2.3.1.3.1.1.33
When a frame has both IP priority fields and IEEE 802.1ac tags and both sfbrm100PortUseIPTC and sfbrm100PortUseTagTC are enabled then this mib variable is used to decide which traffic class to use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER useIP(1), useTag(2)  

sfbrm100PortVLANTunnel 1.3.6.1.4.1.868.2.3.1.3.1.1.34
For all unicast and multicast frames with destination address defined as 'static' in the address database port-based VLAN masking, 802.1Q VLAN membership masking and trunk masking are enforced. When this mib variable is enabled, these rules are bypassed for all frames ingressing this port, whose destination address is 'static' in the database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortFwdUnknown 1.3.6.1.4.1.868.2.3.1.3.1.1.35
When enabled, all unicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow this frame to egress).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortDefForward 1.3.6.1.4.1.868.2.3.1.3.1.1.36
When enabled, all multicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow this frame to egress).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortAdminState 1.3.6.1.4.1.868.2.3.1.3.1.1.37
Set port state administratively up or down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortVTUPriOverride 1.3.6.1.4.1.868.2.3.1.3.1.1.38
When disabled, normal switch operation is done. When enabled, VTU Priority override occurs. i.e The determined VID priority takes precedence over all other priorities of that frame as per the VLAN database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortSAPriOverride 1.3.6.1.4.1.868.2.3.1.3.1.1.39
When enabled, Source address decides the priority as per the address database entry rules.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortDAPriOverride 1.3.6.1.4.1.868.2.3.1.3.1.1.40
When enabled, Destination address decides the priority as per the address database entry rules.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortVLANStatus 1.3.6.1.4.1.868.2.3.1.3.1.1.41
802.1Q VLAN setting : vlanDisabled - 802.1Q is disabled. fallback - The frame is not discarded if the VID is not in the VLAN Db. check - The VID must be in the VLAN Db, the ingress port may or may not be a member. If the VID is not in the VLAN Db, it is discarded. secure - The VID must be in the VLAN Db and the ingresss port should be a member of the VLAN, else it is discarded. In all the three cases when 802.1Q is enabled, the frame is allowed to egress only if the egress port is a member of the VLAN. In 'fallback' mode, if VID is not in the VLAN db, the frame is allowed to egress based on Port Based VLAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vlanDisabled(1), fallback(2), check(3), secure(4)  

sfbrm100PortDiscardTagged 1.3.6.1.4.1.868.2.3.1.3.1.1.42
All ingress tagged frames are discarded if enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortDiscardUntagged 1.3.6.1.4.1.868.2.3.1.3.1.1.43
All untagged ingress frames are discarded if enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortEgressMonitor 1.3.6.1.4.1.868.2.3.1.3.1.1.44
Any frame that egress this port is also sent to the egress monitor destination port. Not applicable for 2-port device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortIngressMonitor 1.3.6.1.4.1.868.2.3.1.3.1.1.45
Any frame that ingress this port is also sent to the ingress monitor destination port. Not applicable for 2-port device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortPri3IngressRateCtrl 1.3.6.1.4.1.868.2.3.1.3.1.1.46
Ingress rate limit for Priority 3 frames, but not faster than port speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sameAsPri2(1), twiceAsPri2(2)  

sfbrm100PortPri2IngressRateCtrl 1.3.6.1.4.1.868.2.3.1.3.1.1.47
Ingress rate limit for Priority 2 frames, but not faster than port speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sameAsPri1(1), twiceAsPri1(2)  

sfbrm100PortPri1IngressRateCtrl 1.3.6.1.4.1.868.2.3.1.3.1.1.48
Ingress rate limit for Priority 1 frames, but not faster than port speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sameAsPri0(1), twiceAsPri0(2)  

sfbrm100PortPri0IngressRate 1.3.6.1.4.1.868.2.3.1.3.1.1.49
Ingress rate for Priority 0 frames in bits per second, but not faster than port speed. Priority 0 frames are discarded after the ingress rate selected is reached or exceeded. The rates of 128M and 256M are valid for Gigabit ports only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLimit(1), rate64K(2), rate96K(3), rate128K(4), rate160K(5), rate192K(6), rate224K(7), rate256K(8), rate320K(9), rate384K(10), rate512K(11), rate768K(12), rate1M(13), rate1-2M(14), rate1-5M(15), rate2M(16), rate3M(17), rate4M(18), rate5M(19), rate8M(20), rate10M(21), rate20M(22), rate30M(23), rate40M(24), rate60M(25), rate80M(26), rate128M(27), rate256M(28)  

sfbrm100PortIngressLimitMode 1.3.6.1.4.1.868.2.3.1.3.1.1.50
Ingress Limit mode. all(1) - Limits and counts all frames bCastMCastFloodedUCast(2) - Limits and counts all broadcast, multicast and flooded unicast frames. bCastMCastOnly(3) - Limits and counts all broadcast and multicast frames only. bCastOnly(4) - Limits and counts only broadcast frames. If a frame is not limited by the above setting, its size is not counted against the limit of the other frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all(1), bCastMCastFloodedUCast(2), bCastMCastOnly(3), bCastOnly(4)  

sfbrm100PortEgressRate 1.3.6.1.4.1.868.2.3.1.3.1.1.51
Egress priority rate in bits per seconds. This affects the port's effective transmission rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLimit(1), rate64K(2), rate96K(3), rate128K(4), rate160K(5), rate192K(6), rate224K(7), rate256K(8), rate320K(9), rate384K(10), rate512K(11), rate768K(12), rate1M(13), rate1-2M(14), rate1-5M(15), rate2M(16), rate3M(17), rate4M(18), rate5M(19), rate8M(20), rate10M(21), rate20M(22), rate30M(23), rate40M(24), rate60M(25), rate80M(26), rate128M(27), rate256M(28)  

sfbrm100PortDefaultPriority 1.3.6.1.4.1.868.2.3.1.3.1.1.52
The default priority of the frame if its not IEEE tagged or not IP frames or no other priority overides are active for this frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortForceDefVLANId 1.3.6.1.4.1.868.2.3.1.3.1.1.53
Force to use the sfbrm100PortDefaultVLANId when 802.1Q is enabled on this port. The frames actual VLAN id is replaced with the default VLAN Id. Has no effect when 802.1Q is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortDefaultVLANId 1.3.6.1.4.1.868.2.3.1.3.1.1.54
The default VLAN Id of the port. All untagged frames that are to exit tagged will use the VID of the ingress port on exit. This VID is also used on all frames when 'sfbrm100PortForceDefVLANId' is set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortBasedVLANTbl 1.3.6.1.4.1.868.2.3.1.3.1.1.55
Each bit represents ports on the switch. These bits restrict where this port can send frames to, setting the bits to zero will disable this port's ability to egress frames out of the indicated port. Ex: Port 0 is represented by bit 0 in the bitmap. By default all ports can send to all ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap0 1.3.6.1.4.1.868.2.3.1.3.1.1.56
All Frames with priority 0 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap1 1.3.6.1.4.1.868.2.3.1.3.1.1.57
All Frames with priority 1 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap2 1.3.6.1.4.1.868.2.3.1.3.1.1.58
All Frames with priority 2 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap3 1.3.6.1.4.1.868.2.3.1.3.1.1.59
All Frames with priority 3 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap4 1.3.6.1.4.1.868.2.3.1.3.1.1.60
All Frames with priority 4 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap5 1.3.6.1.4.1.868.2.3.1.3.1.1.61
All Frames with priority 5 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap6 1.3.6.1.4.1.868.2.3.1.3.1.1.62
All Frames with priority 6 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIEEEPriRemap7 1.3.6.1.4.1.868.2.3.1.3.1.1.63
All Frames with priority 7 are remapped to this set value inside the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100PortVCTest 1.3.6.1.4.1.868.2.3.1.3.1.1.64
The virtual cable test can be done using this variable set to perform(1), otherwise the Read-only value notApplicable(2) will be returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER perform(1), doNothing(2)  

sfbrm100PortVCTxMDI0Status 1.3.6.1.4.1.868.2.3.1.3.1.1.65
The test status of the Tx pair or MDI[0](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Test was successful, cable has impedance mismatch. shortInCable(3) - Test was successful, short in cable (impedance < 33 Ohm) openInCable(4) - Test was successful, open in cable (impedance > 333 Ohm) failed(5) - Test failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), impedanceMismatch(2), shortInCable(3), openInCable(4), failed(5), notApplicable(6)  

sfbrm100PortTxMDI0Dist 1.3.6.1.4.1.868.2.3.1.3.1.1.66
The cable distance of the Tx pair or MDI[0](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the distance from the port where the impedance occured. In case of normal(1) cable status, one of the listed value is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lessThan50m(1), between50m80m(2), between80m110m(3), between110m140m(4), morethan140m(5), notApplicable(6)  

sfbrm100PortVCRxMDI1Status 1.3.6.1.4.1.868.2.3.1.3.1.1.67
The test status of the Rx or MDI[1](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Test was successful, cable has impedance mismatch. shortInCable(3) - Test was successful, short in cable (impedance < 33 Ohm) openInCable(4) - Test was successful, open in cable (impedance > 333 Ohm) failed(5) - Test failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), impedanceMismatch(2), shortInCable(3), openInCable(4), failed(5), notApplicable(6)  

sfbrm100PortRxMDI1Dist 1.3.6.1.4.1.868.2.3.1.3.1.1.68
The cable distance of the Rx pair or MDI[1](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the distance from the port where the impedance occured.In case of normal(1) cable status, one of the listed value is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lessThan50m(1), between50m80m(2), between80m110m(3), between110m140m(4), morethan140m(5), notApplicable(6)  

sfbrm100PortVCMDI2Status 1.3.6.1.4.1.868.2.3.1.3.1.1.69
The test status of the MDI[2](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Test was successful, cable has impedance mismatch. shortInCable(3) - Test was successful, short in cable (impedance < 33 Ohm) openInCable(4) - Test was successful, open in cable (impedance > 333 Ohm) failed(5) - Test failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), impedanceMismatch(2), shortInCable(3), openInCable(4), failed(5), notApplicable(6)  

sfbrm100PortMDI2Dist 1.3.6.1.4.1.868.2.3.1.3.1.1.70
The cable distance of the MDI[2](if Gigabit port else notApplicable(6)) from the test port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the distance from the port where the impedance occured.In case of normal(1) cable status, one of the listed value is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lessThan50m(1), between50m80m(2), between80m110m(3), between110m140m(4), morethan140m(5), notApplicable(6)  

sfbrm100PortVCMDI3Status 1.3.6.1.4.1.868.2.3.1.3.1.1.71
The test status of the MDI[3](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open in cable) impedanceMismatch(2)- Test was successful, cable has impedance mismatch. shortInCable(3) - Test was successful, short in cable (impedance < 33 Ohm) openInCable(4) - Test was successful, open in cable (impedance > 333 Ohm) failed(5) - Test failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), impedanceMismatch(2), shortInCable(3), openInCable(4), failed(5), notApplicable(6)  

sfbrm100PortMDI3Dist 1.3.6.1.4.1.868.2.3.1.3.1.1.72
The cable distance of the MDI[3](if Gigabit port else notApplicable(6)) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a value of 2 - 4, this gives the distance from the port where the impedance occured.In case of normal(1) cable status, one of the listed value is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lessThan50m(1), between50m80m(2), between80m110m(3), between110m140m(4), morethan140m(5), notApplicable(6)  

sfbrm100PortResetCounters 1.3.6.1.4.1.868.2.3.1.3.1.1.73
Resets all the port counters for this port. A read returns read-only value donothing(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), donothing(2)  

sfbrm100PortIPTrafficAccess 1.3.6.1.4.1.868.2.3.1.3.1.1.74
Allow/block IP management traffic on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortResetOAMCounters 1.3.6.1.4.1.868.2.3.1.3.1.1.75
Resets all OAM counters for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortForceAutoUpgrade 1.3.6.1.4.1.868.2.3.1.3.1.1.76
Force Automatic firmware upgrade on this peer, when the peer has its auto upgrade turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfbrm100PortModeType 1.3.6.1.4.1.868.2.3.1.3.1.1.77
The Interface mode. The capabilities of the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mode10or100or1000BaseT(1), mode1000BaseX(2), mode10or100BaseT(3), mode100BaseFX(4)  

sfbrm100PortOAMMode 1.3.6.1.4.1.868.2.3.1.3.1.1.78
The OAM mode for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER passive(1), active(2)  

sfbrm100PortPhyNumber 1.3.6.1.4.1.868.2.3.1.3.1.1.79
This gives the physical port number on the hardware switch. This is useful in computing the port based VLAN setting for this port. The bit position in the port based VLAN corresponds to this physical port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIngressRateLimit2 1.3.6.1.4.1.868.2.3.1.3.1.1.80
Ingress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if the ingress rate selected is reached or exceeded. Devices which support this mib variable do not use 'sfbrm100PortPri0IngressRate' for rate limiting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLimit(1), rate64K(2), rate128K(3), rate192K(4), rate256K(5), rate320K(6), rate384K(7), rate512K(8), rate768K(9), rate1M(10), rate2M(11), rate3M(12), rate4M(13), rate6M(14), rate8M(15), rate10M(16), rate20M(17), rate30M(18), rate40M(19), rate50M(20), rate60M(21), rate70M(22), rate80M(23), rate100M(24), rate200M(25), rate300M(26), rate400M(27), rate500M(28), rate600M(29), rate700M(30), rate800M(31), rate900M(32)  

sfbrm100PortEgressRateLimit2 1.3.6.1.4.1.868.2.3.1.3.1.1.81
Egress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if over the limit. Devices which support this mib variable do not use 'sfbrm100PortEgressRate' for rate limiting
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLimit(1), rate64K(2), rate128K(3), rate192K(4), rate256K(5), rate320K(6), rate384K(7), rate512K(8), rate768K(9), rate1M(10), rate2M(11), rate3M(12), rate4M(13), rate6M(14), rate8M(15), rate10M(16), rate20M(17), rate30M(18), rate40M(19), rate50M(20), rate60M(21), rate70M(22), rate80M(23), rate100M(24), rate200M(25), rate300M(26), rate400M(27), rate500M(28), rate600M(29), rate700M(30), rate800M(31), rate900M(32)  

sfbrm100PortStatsTable 1.3.6.1.4.1.868.2.3.1.3.2
Port Statistics table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100PortStatsEntry

sfbrm100PortStatsEntry 1.3.6.1.4.1.868.2.3.1.3.2.1
Statistics for a single port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100PortStatsEntry  

sfbrm100PortLocStatsIndex 1.3.6.1.4.1.868.2.3.1.3.2.1.1
The port index of the local port as defined by sfbrm100PortLocIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortRmtStatsIndex 1.3.6.1.4.1.868.2.3.1.3.2.1.2
The remote port index of the remote peer as defined by sfbrm100PortRmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInGoodOctetsLo 1.3.6.1.4.1.868.2.3.1.3.2.1.3
The lower 32-bits of the received good octets counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInGoodOctetsHi 1.3.6.1.4.1.868.2.3.1.3.2.1.4
The upper 32-bits of the received good octets counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInBadOctets 1.3.6.1.4.1.868.2.3.1.3.2.1.5
The sum of all octets in bad Ethernet frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInUnicasts 1.3.6.1.4.1.868.2.3.1.3.2.1.6
The number of good unicast frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInBroadcasts 1.3.6.1.4.1.868.2.3.1.3.2.1.7
The number of good broadcast frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInMulticasts 1.3.6.1.4.1.868.2.3.1.3.2.1.8
The number of good multicast frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInPause 1.3.6.1.4.1.868.2.3.1.3.2.1.9
The number of good Pause flow control frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInUndersize 1.3.6.1.4.1.868.2.3.1.3.2.1.10
The number of frames received with a length of less than 64 octets with a valid FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInFragments 1.3.6.1.4.1.868.2.3.1.3.2.1.11
The number of frames received with a length of less than 64 octets with an invalid FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInOversize 1.3.6.1.4.1.868.2.3.1.3.2.1.12
The number of frames received with a length of more than maximum size octets with a valid FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInJabber 1.3.6.1.4.1.868.2.3.1.3.2.1.13
The number of frames received with a length of more than maximum size octets with an invalid FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInRxErr 1.3.6.1.4.1.868.2.3.1.3.2.1.14
The number of frames received with a RxErr signal from the Physical layer
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInFCSErr 1.3.6.1.4.1.868.2.3.1.3.2.1.15
The number of frames received with a CRC error not counted in sfbrm100PortInFragments, sfbrm100PortInJabber or sfbrm100PortInRxErr.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn64Octets 1.3.6.1.4.1.868.2.3.1.3.2.1.16
The total number of frames received with a length of 64 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn65to127Octets 1.3.6.1.4.1.868.2.3.1.3.2.1.17
The total number of frames received with a length between 65 and 127 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn128to255Octets 1.3.6.1.4.1.868.2.3.1.3.2.1.18
The total number of frames received with a length between 128 and 255 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn256to511Octets 1.3.6.1.4.1.868.2.3.1.3.2.1.19
The total number of frames received with a length between 256 and 511 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn512to1023Octets 1.3.6.1.4.1.868.2.3.1.3.2.1.20
The total number of frames received with a length between 512 and 1023 octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortIn1024toMaxOctets 1.3.6.1.4.1.868.2.3.1.3.2.1.21
The total number of frames received with a length between 1024 and max size octets, including errored frames. This is a histogram counter, dependent on the histogram mode 'sfbrm100SwHistMode' chosen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutOctetsLo 1.3.6.1.4.1.868.2.3.1.3.2.1.22
The lower 32-bit of the sum of all frames sent from this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutOctetsHi 1.3.6.1.4.1.868.2.3.1.3.2.1.23
The upper 32-bit of the sum of all frames sent from this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutUnicasts 1.3.6.1.4.1.868.2.3.1.3.2.1.24
The number of unicast frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutBroadcasts 1.3.6.1.4.1.868.2.3.1.3.2.1.25
The number of broadcast frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutMulticasts 1.3.6.1.4.1.868.2.3.1.3.2.1.26
The number of multicast frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutPause 1.3.6.1.4.1.868.2.3.1.3.2.1.27
The number of Pause frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutDeferred 1.3.6.1.4.1.868.2.3.1.3.2.1.28
The number of frames transmitted with a delay.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutCollisions 1.3.6.1.4.1.868.2.3.1.3.2.1.29
The number of collisions during transmission not including single, multiple, excessive or late collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutSingle 1.3.6.1.4.1.868.2.3.1.3.2.1.30
The number of frames transmitted with exactly one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutMultiple 1.3.6.1.4.1.868.2.3.1.3.2.1.31
The number of frames transmitted with more than one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutExcessive 1.3.6.1.4.1.868.2.3.1.3.2.1.32
The number of frames dropped due to excessive collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutLate 1.3.6.1.4.1.868.2.3.1.3.2.1.33
The number of times a collision is detected later than 512 bits-times into transmission of a frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutFCSErr 1.3.6.1.4.1.868.2.3.1.3.2.1.34
The number of frames transmitted with invalid FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInDiscard 1.3.6.1.4.1.868.2.3.1.3.2.1.35
The number of good frames that were discarded due to lack of resources.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortInFiltered 1.3.6.1.4.1.868.2.3.1.3.2.1.36
The number of good frames filtered due to ingress switch policy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortOutFiltered 1.3.6.1.4.1.868.2.3.1.3.2.1.37
The number of good frames filtered due to egress switch policy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMITable 1.3.6.1.4.1.868.2.3.1.3.3
DMI ports on the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100DMIEntry

sfbrm100DMIEntry 1.3.6.1.4.1.868.2.3.1.3.3.1
Status of the DMI ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100DMIEntry  

sfbrm100DMILocPortIndex 1.3.6.1.4.1.868.2.3.1.3.3.1.1
The port index of the DMI port as defined by sfbrm100PortLocIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMIRmtPortIndex 1.3.6.1.4.1.868.2.3.1.3.3.1.2
The port index of the DMI port as defined by sfbrm100PortRmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMIRxPwrLvlPreset 1.3.6.1.4.1.868.2.3.1.3.3.1.3
A preset level for Rx Power on the Fiber port, if the DMI read value falls below the preset value, an intrusion is detected, and a trap is generated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100DMIConnType 1.3.6.1.4.1.868.2.3.1.3.3.1.4
The DMI connector type indicates the external optical or electrical cable connector provided as the interface. From SFF 8472 Rev 9.5 Value Description of connector 00h Unknown or unspecified 01h SC 02h Fibre Channel Style 1 copper connector 03h Fibre Channel Style 2 copper connector 04h BNC/TNC 05h Fibre Channel coaxial headers 06h FiberJack 07h LC 08h MT-RJ 09h MU 0Ah SG 0Bh Optical pigtail 0C-1Fh Reserved 20h HSSDC II 21h Copper Pigtail 22h-7Fh Reserved 80-FFh Vendor specific
Status: mandatory Access: read-only
OBJECT-TYPE    
  CpsConnector  

sfbrm100DMIBitRate 1.3.6.1.4.1.868.2.3.1.3.3.1.5
Bitrate in units of 100Mbps.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILenFor9x125umKM 1.3.6.1.4.1.868.2.3.1.3.3.1.6
Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of KM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILenFor9x125um100M 1.3.6.1.4.1.868.2.3.1.3.3.1.7
Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of 100m.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILenFor50x125um10M 1.3.6.1.4.1.868.2.3.1.3.3.1.8
Specifies the link length that is supported by the transceiver while operating in 50 micron multi mode fiber. The value is in units of 10m.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILenFor625x125um10M 1.3.6.1.4.1.868.2.3.1.3.3.1.9
Specifies the link length that is supported by the transceiver while operating in 62.5 micron multi mode fiber. The value is in units of 10m.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILenForCopper 1.3.6.1.4.1.868.2.3.1.3.3.1.10
Specifies the link length that is supported by the transceiver while operating in copper cable. The value is in units of meters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMIId 1.3.6.1.4.1.868.2.3.1.3.3.1.11
Specifies the physical device. The table below from SFF-8472 Rev 9.5 Standard gives description for the values. 00h Unknown or unspecified 01h GBIC 02h Module/connector soldered to motherboard 03h SFP 04-7Fh Reserved 80-FFh Vendor specific.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMILaserWavelength 1.3.6.1.4.1.868.2.3.1.3.3.1.12
The Nominal transmitter output wavelength at room temperature. The units in nm
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMITemperature 1.3.6.1.4.1.868.2.3.1.3.3.1.13
Temperature of fiber transceiver in tenths of degrees C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMITempAlarm 1.3.6.1.4.1.868.2.3.1.3.3.1.14
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(6), highAlarm(7)  

sfbrm100DMITxBiasCurrent 1.3.6.1.4.1.868.2.3.1.3.3.1.15
Transmit bias current on local fiber interface, in microamperes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMITxBiasAlarm 1.3.6.1.4.1.868.2.3.1.3.3.1.16
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(6), highAlarm(7)  

sfbrm100DMITxPowerLevel 1.3.6.1.4.1.868.2.3.1.3.3.1.17
DMI: Diagnostic Monitoring Interface for fiber transceivers. Transmit power on local fiber measured in microwatts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMITxPowerAlarm 1.3.6.1.4.1.868.2.3.1.3.3.1.18
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(6), highAlarm(7)  

sfbrm100DMIRxPowerLevel 1.3.6.1.4.1.868.2.3.1.3.3.1.19
DMI: Diagnostic Monitoring Interface for fiber transceivers. Receive power on local fiber measured in microwatts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100DMIRxPowerAlarm 1.3.6.1.4.1.868.2.3.1.3.3.1.20
.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(6), highAlarm(7)  

sfbrm100PortL2CPTable 1.3.6.1.4.1.868.2.3.1.3.4
Port L2CP processing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100PortL2CPEntry

sfbrm100PortL2CPEntry 1.3.6.1.4.1.868.2.3.1.3.4.1
Status and configuration entries for a each port on the device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100PortL2CPEntry  

sfbrm100PortL2CPLocIndex 1.3.6.1.4.1.868.2.3.1.3.4.1.1
Uniquely indentifies each port on the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100PortL2CPRmtIndex 1.3.6.1.4.1.868.2.3.1.3.4.1.2
Uniquely indentifies each port on the peer device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100STPProtocolsFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.3
Any STP/RSTP/MSTP protocol frames with destination address of 01-80-C2-00-00-00 is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100SlowProtocolsFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.4
Any LACP/LAMP protocol frames with destination address of 01-80-C2-00-00-02 is discarded at this port or tunnelled. Since this device pairs link OAM frames, these frames will not forwarded or discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100PortAuthProtocolFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.5
Port authentication protocol frames with destination address of 01-80-C2-00-00-03 is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100ELMIProtocolFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.6
E-LMI protocol frames with destination address of 01-80-C2-00-00-07 is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100LLDPProtocolFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.7
LLDP protocol frames with destination address of 01-80-C2-00-00-0E is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100BridgeMgmtProtocolsFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.8
Bridge Management protocol frames with destination address of 01-80-C2-00-00-10 is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100GARPBlockProtocolsFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.9
GARP/MRP with destination address of 01-80-C2-00-00-20 to 01-80-C2-00-00-2F is discarded at this port or tunnelled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100BridgeBlkOtherMulticastsFwd 1.3.6.1.4.1.868.2.3.1.3.4.1.10
This mib variable tunnels or discards all the IEEE multicast frames in the bridge block of addresses [01-80-C2-00-00-20 to 01-80-C2-00-00-0F]. The mib variables applies to all addresses in this block that are not covered by the other mib variables in this table. i.e this is not applicable for STP, slow protocols, etc.,
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tunnel(1), discard(2)  

sfbrm100FwdDBTable 1.3.6.1.4.1.868.2.3.1.4.1
Learned address database for this device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100FwdDBEntry

sfbrm100FwdDBEntry 1.3.6.1.4.1.868.2.3.1.4.1.1
Status and configuration entries for a single port on this device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100FwdDBEntry  

sfbrm100FwdLocPortIndex 1.3.6.1.4.1.868.2.3.1.4.1.1.1
The entry can belong to the local switch or one of the remote peers. The local switch has the index as zero. The remote peers have the port index of the local port to which they are connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100FwdDBNum 1.3.6.1.4.1.868.2.3.1.4.1.1.2
The Address Database Number the entry belongs to. DBNum of 0 is the default database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

sfbrm100FwdMacAddress 1.3.6.1.4.1.868.2.3.1.4.1.1.3
The unicast or multicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

sfbrm100FwdConnPort 1.3.6.1.4.1.868.2.3.1.4.1.1.4
The index of the logical Port from sfbrm100PortTable to which the MAC address is connected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100FwdPriority 1.3.6.1.4.1.868.2.3.1.4.1.1.5
The priority of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100FwdEntryType 1.3.6.1.4.1.868.2.3.1.4.1.1.6
The Entry state of this unicast or multicast entry. The types represent : static(1) - A Valid entry that doesnot age. staticNRL(2) - A static entry that has no ingress rate limiting. staticPA(3) - A static entry that has priority override enabled. dynamic(4) - A valid entry with no special attributes which ages and finally removed from the database. A unicast entry can be static(1) or staticPA(3) but not staticNRL(2). For MAC address which are learned, the read-only value of dynamic(4) is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER static(1), staticNRL(2), staticPA(3), dynamic(4)  

sfbrm100FwdEntryStatus 1.3.6.1.4.1.868.2.3.1.4.1.1.7
The status of the row and operations on the entry. write(1) is used to create a entry with default values. Immediately after completing the add operation, the agent sets this object to valid(1) if the operation was successful. It is also used to change the existing entry's properties like priority, type and port associations. delete(2) is used to delete any entries created by the managment station. An entry in the read-only value of valid(3) state is fully configured and consistent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER write(1), delete(2), valid(3)  

sfbrm100VlanTable 1.3.6.1.4.1.868.2.3.1.4.2
VLAN database for this device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Sfbrm100VlanEntry

sfbrm100VlanEntry 1.3.6.1.4.1.868.2.3.1.4.2.1
Status and configuration entries for a single port on this device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Sfbrm100VlanEntry  

sfbrm100VlanLocPortIndex 1.3.6.1.4.1.868.2.3.1.4.2.1.1
The entry can belong to the local switch or one of the remote peers. The local switch has the index as zero. The remote peers have the port index of the local port to which they are connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100VlanDBNum 1.3.6.1.4.1.868.2.3.1.4.2.1.2
The Address Database Number the entry belongs to. DBNum of 0 is the default database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

sfbrm100VlanVID 1.3.6.1.4.1.868.2.3.1.4.2.1.3
The VLAN ID of the entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfbrm100VlanVIDPriOverride 1.3.6.1.4.1.868.2.3.1.4.2.1.4
Override Priority on frames assosicated with this VID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sfbrm100VlanVIDPriority 1.3.6.1.4.1.868.2.3.1.4.2.1.5
Priority for frames assosicated with this VID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfbrm100VlanMemTagPort1 1.3.6.1.4.1.868.2.3.1.4.2.1.6
Membership and Egress Tagging on Logical Port 1. memEgressNoMode(1)- Port 1 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 1 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 1 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 1 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort2 1.3.6.1.4.1.868.2.3.1.4.2.1.7
Membership and Egress Tagging on Logical Port 2. memEgressNoMode(1)- Port 2 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 2 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 2 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 2 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort3 1.3.6.1.4.1.868.2.3.1.4.2.1.8
Membership and Egress Tagging on Logical Port 3. memEgressNoMode(1)- Port 3 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 3 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 3 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 3 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort4 1.3.6.1.4.1.868.2.3.1.4.2.1.9
Membership and Egress Tagging on Logical Port 4. memEgressNoMode(1)- Port 4 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 4 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 4 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 4 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort5 1.3.6.1.4.1.868.2.3.1.4.2.1.10
Membership and Egress Tagging on Logical Port 5. memEgressNoMode(1)- Port 5 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 5 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 5 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 5 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort6 1.3.6.1.4.1.868.2.3.1.4.2.1.11
Membership and Egress Tagging on Logical Port 6. memEgressNoMode(1)- Port 6 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 6 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 6 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 6 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort7 1.3.6.1.4.1.868.2.3.1.4.2.1.12
Membership and Egress Tagging on Logical Port 7. memEgressNoMode(1)- Port 7 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 7 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 7 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 7 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort8 1.3.6.1.4.1.868.2.3.1.4.2.1.13
Membership and Egress Tagging on Logical Port 8. memEgressNoMode(1)- Port 8 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 8 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 8 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 8 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort9 1.3.6.1.4.1.868.2.3.1.4.2.1.14
Membership and Egress Tagging on Logical Port 9. memEgressNoMode(1)- Port 9 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 9 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 9 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 9 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanMemTagPort10 1.3.6.1.4.1.868.2.3.1.4.2.1.15
Membership and Egress Tagging on Logical Port 10. memEgressNoMode(1)- Port 10 is a member of this VLAN and frames that egress are unmodified. memEgressNoTag(2) - Port 10 is a member of this VLAN and frames that egress are untagged. memEgressTag(3) - Port 10 is a member of this VLAN and frames that egress are tagged. notMember(4) - Port 10 is not a member of this VLAN and frames that ingress with this VID are discarded. notApplicable(5) is returned if there is no valid port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memEgressNoMod(1), memEgressNoTag(2), memEgressTag(3), notMember(4), notApplicable(5)  

sfbrm100VlanEntryStatus 1.3.6.1.4.1.868.2.3.1.4.2.1.16
The status of the row and operations on the entry. write(1) is used to create a entry with default values. Immediately after completing the add operation, the agent sets this object to valid(1) if the operation was successful. It is also used to change the existing entry's properties like priority, type and port associations. delete(2) is used to delete any entries created by the managment station. An entry in the read-only value of valid(3) state is fully configured and consistent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER write(1), delete(2), valid(3)  

sfbrm100ATUDbFull 119
The Address Translation Database is full, no more entries can be added.
TRAP-TYPE    

sfbrm100VTUMemberViolation 120
A Frame with VLAN ID found in the VLAN Table has been received, but the Ingress port is not a member of the VLAN.
TRAP-TYPE    

sfbrm100VTUMissViolation 121
A Frame with a VLAN ID not in VLAN Table is received.
TRAP-TYPE    

sfbrm100ATUMemberViolation 122
A Source address look-up in the Address Database finds a entry but the ingress port is not on the list of source port.
TRAP-TYPE    

sfbrm100ATUMissViolation 123
A source address look-up in the Address Database resulted in a miss.
TRAP-TYPE    

sfbrm100OAMRemoteDetected 124
A OAM peer is detected and active OAM communication is established with the Peer.
TRAP-TYPE    

sfbrm100EEPROMOnFiber 125
EEPROM for monitoring, is detected on this port.
TRAP-TYPE    

sfbrm100DMIOnFiber 126
DMI is detected on this port.
TRAP-TYPE    

sfbrm100LinkChanged 127
A Link Status change occurred.
TRAP-TYPE    

sfbrm100DMILowRxIntrusion 128
Intrusion detected on Rx Power.
TRAP-TYPE    

sfbrm100DMILowRxPower 129
Rx Power Alarm.
TRAP-TYPE    

sfbrm100DMILowTxPower 130
Tx Power Alarm.
TRAP-TYPE    

sfbrm100DMILowTxBias 131
Transmit bias alarm.
TRAP-TYPE    

sfbrm100DMILowTemperature 132
Temperature alarm.
TRAP-TYPE    

sfbrm100LastGasp 133
The Last gasp from the local device.
TRAP-TYPE    

sfbrm100OAMPeerLinkDown 134
The remote port is down on the peer.
TRAP-TYPE    

sfbrm100OAMPeerLinkUp 135
The remote port is up on the peer.
TRAP-TYPE    

sfbrm100OAMPeerDyingGasp 136
The remote peer OAM dying gasp trap.
TRAP-TYPE    

sfbrm100OAMThresholdEvent 137
Local/remote peer's OAM Threshold crossing traps.
TRAP-TYPE    

sfbrm100PeerVersionMismatch 138
The remote peer is running a different firmware than local. The remote peer needs upgrading.
TRAP-TYPE