TY1250I-MIB

File: TY1250I-MIB.mib (46656 bytes)

Imported modules

SNMPv2-TC	RFC1155-SMI	RFC-1215
RFC-1212

Imported symbols

DisplayString	Counter	TimeTicks
enterprises	IpAddress	TRAP-TYPE
OBJECT-TYPE

Defined Types

Ty1250CfgMaintEntry
SEQUENCE
	ty1250CfgMaintIndex	INTEGER	1..2
	ty1250CfgMaintMode	INTEGER
	ty1250CfgMaintBaud	INTEGER
	ty1250CfgMaintDataBits	INTEGER
	ty1250CfgMaintStopBits	INTEGER
	ty1250CfgMaintParity	INTEGER
	ty1250CfgMaintFlowCtrl	INTEGER

Defined Values

tylink		1.3.6.1.4.1.466
OBJECT IDENTIFIER

dsucsu		1.3.6.1.4.1.466.1
OBJECT IDENTIFIER

tyview		1.3.6.1.4.1.466.2
OBJECT IDENTIFIER

ty1250		1.3.6.1.4.1.466.3
OBJECT IDENTIFIER

ty1250SysTable		1.3.6.1.4.1.466.3.1
OBJECT IDENTIFIER

ty1250SysType		1.3.6.1.4.1.466.3.1.1
A textual description of the system model identifier. for example: TYLINK1250
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

ty1250SysSoftRev		1.3.6.1.4.1.466.3.1.2
Displays the Software Revision installed in this node.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

ty1250SysHardRev		1.3.6.1.4.1.466.3.1.3
Displays the Hardware Revision of the node.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

ty1250SysNumNetInstalled		1.3.6.1.4.1.466.3.1.4
The number of Network (DDS) ports that are installed. There is 1 on the 1250.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

ty1250SysNumDteInstalled		1.3.6.1.4.1.466.3.1.5
The number of channels (DTE) that are installed. There is 1 on the 1250.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..1

ty1250SysNumMaintInstalled		1.3.6.1.4.1.466.3.1.6
The number of Maintenance ports that are installed. There are 2 on the 1250.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..2

ty1250SysName		1.3.6.1.4.1.466.3.1.7
The user supplied name of the node. This object does not affect operation, but may be useful for network management.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

ty1250CfgAppTable		1.3.6.1.4.1.466.3.2
OBJECT IDENTIFIER

ty1250CfgAppClockSource		1.3.6.1.4.1.466.3.2.2
Default timing, or clock, source. There must be only one source on a DDS line. Node should always be network (2) timed on a point-to-network application. Line Driver applications need one node as internal (1), one as network (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), network(2)

ty1250CfgAppCircuitId		1.3.6.1.4.1.466.3.2.3
Circuit identifier provided by the service provider.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

ty1250CfgNetTable		1.3.6.1.4.1.466.3.3
OBJECT IDENTIFIER

ty1250CfgNetType		1.3.6.1.4.1.466.3.3.11
Indicates type of service purchased on the attached network line (DDS or SW56). Valid selections are dedicated (1) and switch56 (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dedicated(1), switch56(2)

ty1250CfgNetGlareType		1.3.6.1.4.1.466.3.3.4
In switched applications, defines who wins when there are simultanious incomming and outgoing calls. If in doubt, select external-glare (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	external-glare(1), internal-glare(2)

ty1250CfgNetEchoCan		1.3.6.1.4.1.466.3.3.5
In switched applications, some carriers, such as Sprint, require you to disable-echo-cancellors (2) for data apps on most lines. Calls take longer to come up when disabling is done; use ignore-echo-cancellers (1) on clear channel lines.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ignore-echo-cancellers(1), disable-echo-cancellers(2)

ty1250CfgNetAnsMode		1.3.6.1.4.1.466.3.3.6
In switched applications, allows for manual-answer (1) or automatic-answer (2) of inbound calls. Calls may be answered in manual mode via vt100, DTR, or the front panel button if so configured.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	manual-answer(1), automatic-answer(2)

ty1250CfgNetDialTimeout		1.3.6.1.4.1.466.3.3.7
In switched applications, time in seconds to wait for far end to answer before giving up, and possibly redialing.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

ty1250CfgNetNumRedial		1.3.6.1.4.1.466.3.3.8
In switched applications, number of times to redial if the call fails.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

ty1250CfgNetRedialDelay		1.3.6.1.4.1.466.3.3.9
In switched applications, delay in seconds between redial attempts.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

ty1250CfgNetDefNum2Dial		1.3.6.1.4.1.466.3.3.10
In switched applications, default phone number to dial. Numbers and dashes are allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

ty1250CfgNetBPVThresholding		1.3.6.1.4.1.466.3.3.12
Allows the user to turn on and off the BPV thresholding function. Valid values are thresholding_at_10E-4 (1) and disable-thresholding (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	thresholding-at-10E-4(1), disable-thresholding(2)

ty1250CfgDteTable		1.3.6.1.4.1.466.3.4
OBJECT IDENTIFIER

ty1250CfgDteType		1.3.6.1.4.1.466.3.4.1
The Dte channel type identifies the electrical specification of the interface. Read-only.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	v35(2), rs449(3)

ty1250CfgDteClockInvert		1.3.6.1.4.1.466.3.4.5
Clock Inversion, invert-dte-clock (2), can be used to solve out of phase timing problems on DTE link. normal-dte-clock (1) can be used in most cases.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal-dte-clock(1), invert-dte-clock(2)

ty1250CfgDteTiming		1.3.6.1.4.1.466.3.4.6
The DTE channel Timing mode. Use loop2-timing (2) when in doubt.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	loop1-timing(1), loop2-timing(2)

ty1250CfgDialTable		1.3.6.1.4.1.466.3.5
OBJECT IDENTIFIER

ty1250CfgDialButton		1.3.6.1.4.1.466.3.5.1
In switched applications, Enables/Disables the button on front of unit. This button can used to manual answer an incomming call, or dial out the default number. The valid values are enable-button (1) and disable-button (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-button(1), disable-button(2)

ty1250CfgDialDtr		1.3.6.1.4.1.466.3.5.2
In switched applications, Enables/Disables dialing on DTR signal transition. Valid values enable-dtr (1) and disable-dtr (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-dtr(1), disable-dtr(2)

ty1250CfgDialRtsDisc		1.3.6.1.4.1.466.3.5.3
In switched applications, Enables/Disables disconnecting on RTS signal transition. Valid values are enable-rts (1) and disable-rts (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-rts(1), disable-rts(2)

ty1250CfgDialRi		1.3.6.1.4.1.466.3.5.4
In switched applications, Enables/Disables incoming call notification to DTE via RI signal. Valid values are enable-ri (1) and disable-ri (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-ri(1), disable-ri(2)

ty1250CfgMaintTable		1.3.6.1.4.1.466.3.6
The Maintenance Port Configuration table contains parameters for the Maintenance ports on the 1250. The Terminal Port is Index=1; SLIP port is 2
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ty1250CfgMaintEntry

ty1250CfgMaintEntry		1.3.6.1.4.1.466.3.6.1
Maintenance Port Configuration Object
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Ty1250CfgMaintEntry

ty1250CfgMaintIndex		1.3.6.1.4.1.466.3.6.1.1
The Maintenance port under consideration. On the 1250, the Terminal Port is Index=1; SLIP port is 2.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..2

ty1250CfgMaintMode		1.3.6.1.4.1.466.3.6.1.2
The Mode for this Maintenance Port. Values include ascii-vt100 (4), slip (7), and cslip (8).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ascii-vt100(4), slip(7), cslip(8)

ty1250CfgMaintBaud		1.3.6.1.4.1.466.3.6.1.3
Baud rate for this Maintenance port. Values are baud-2400 (2), baud-9600 (4), baud-19200 (5).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	baud-2400(2), baud-9600(4), baud-19200(5)

ty1250CfgMaintDataBits		1.3.6.1.4.1.466.3.6.1.4
Databits for this Maintenance port. Values are databits-7 (1) and databits-8 (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	databits-7(1), databits-8(2)

ty1250CfgMaintStopBits		1.3.6.1.4.1.466.3.6.1.5
Number of Stopbits for this Maintenance port. Values are stopbits-1 (1), stopbits-1-5 (2), and stopbits-2 (3).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stopbits-1(1), stopbits-1-5(2), stopbits-2(3)

ty1250CfgMaintParity		1.3.6.1.4.1.466.3.6.1.6
Parity for this Maintenance port. Values are no-parity (1), odd-parity (2), even-parity (3).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no-parity(1), odd-parity(2), even-parity(3)

ty1250CfgMaintFlowCtrl		1.3.6.1.4.1.466.3.6.1.7
Flow Control for this Maintenance port. Values are no-flow-control (1), software-flow-control (2), and hardware-flow-control (3).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no-flow-control(1), software-flow-control(2), hardware-flow-control(3)

ty1250CfgSlipTable		1.3.6.1.4.1.466.3.8
OBJECT IDENTIFIER

ty1250CfgSlipMyIP		1.3.6.1.4.1.466.3.8.1
The IP address for this node.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ty1250CfgSlipPeerIP		1.3.6.1.4.1.466.3.8.2
The IP address for other end of slip connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ty1250CfgSlipMask		1.3.6.1.4.1.466.3.8.3
The IP Network Mask (eg 255.255.255.0) for the SLIP link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ty1250CfgSlipMaxMTU		1.3.6.1.4.1.466.3.8.4
The Maximum Transmission Unit is the size of the largest IP packet supported. This value should be set to the lowest value supported by any equipment in the transmission path. A size of 1006 (including header) is suggested.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

ty1250CfgSnmpTable		1.3.6.1.4.1.466.3.14
OBJECT IDENTIFIER

ty1250CfgSnmpManagerIP		1.3.6.1.4.1.466.3.14.1
The IP address for the SNMP manager to receive this node's TRAPs.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ty1250CfgTelnetTable		1.3.6.1.4.1.466.3.17
OBJECT IDENTIFIER

ty1250CfgTelnetEnable		1.3.6.1.4.1.466.3.17.1
Enables/Disables the telnet feature. Valid values are enable-telnet (1) and disable-telnet (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-telnet(1), disable-telnet(2)

ty1250CfgTelnetAutoLogOut		1.3.6.1.4.1.466.3.17.2
Enables/Disables the telnet auto-logout, logging out the user after a certain length of idle time. Valid values are autologout-at-15-minutes (1) and disable-autologout (2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	autologout-at-15-minutes(1), disable-autologout(2)

ty1250CallTable		1.3.6.1.4.1.466.3.9
OBJECT IDENTIFIER

ty1250CallState		1.3.6.1.4.1.466.3.9.4
Call-related actions: a: Connect (initiate a call), b: Disconnect (terminate a call) c: Answer (answer an incoming call).
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	connect(1), disconnect(2), answer(3)

ty1250CallStatus		1.3.6.1.4.1.466.3.9.1
The call status is shown here.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), idle(2), dialing(3), busy(4), waiting-for-redial(5), redialing(6), active(7), incoming-call(8), line-in-maintenance(253), line-down(254)

ty1250CallNumber		1.3.6.1.4.1.466.3.9.2
The last phone number dialed out.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

ty1250CallUpTime		1.3.6.1.4.1.466.3.9.3
Number of seconds the call has been up.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

ty1250DiagUnitTable		1.3.6.1.4.1.466.3.10
OBJECT IDENTIFIER

ty1250DiagUnitLocLoop		1.3.6.1.4.1.466.3.10.1
Enables the operator to control and examine the UNIT local loopback. This loopback occurs on all network ports transmit and receive logic. The unit will transmit DTE data out to the network as normal, and will also loop DTE data back to the DTE.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-loopback-mode(1), disable-loopback-mode(2)

ty1250DiagUnitReset		1.3.6.1.4.1.466.3.10.2
Enables the operator to remotely reset the unit. Using this command will cause the unit to terminate all its connections and drop data.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	reset-unit(1)

ty1250DiagNetTable		1.3.6.1.4.1.466.3.11
OBJECT IDENTIFIER

ty1250DiagNetLineStatus		1.3.6.1.4.1.466.3.11.1
The Current status of the physical interface. Your network carrier can send Out-of-Service or Maintenance Mode codes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	in-sync(1), out-of-service(2), out-of-frame(3), bpv-threshold-failure(4), loss-of-signal(5), simplex-current-loopback(6)

ty1250DiagNetLclLpbk		1.3.6.1.4.1.466.3.11.2
Enables the operator to control and examine the network local loopback. This loopback occurs on the net side of the local transmit and receive logic. The unit continues to receive data from the network and also loops received data back to the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-loopback-mode(1), disable-loopback-mode(2)

ty1250DiagNetRmtLpbk		1.3.6.1.4.1.466.3.11.3
Enables the operator to examine (ONLY) the status of network loopbacks placed by external equipment, such as your local CO. These loopbacks will loop received network data back out the network, disconnecting the DTE completely.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no-loop-from-remote(1), simplex-current-loop(2), non-latching-loop(3)

ty1250DiagDteTable		1.3.6.1.4.1.466.3.12
OBJECT IDENTIFIER

ty1250DiagDteSigRTS		1.3.6.1.4.1.466.3.12.1
The Dte Channel RTS signal. Values are rts-signal-on (1) and rts-signal-off (2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	rts-signal-on(1), rts-signal-off(2)

ty1250DiagDteSigDTR		1.3.6.1.4.1.466.3.12.2
The Dte Channel DTR signal. Values are dtr-signal-on (1) and dtr-signal-off (2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dtr-signal-on(1), dtr-signal-off(2)

ty1250DiagDteLclLpbk		1.3.6.1.4.1.466.3.12.5
This selection displays the status or controls the Local DTE Channel Loopback for the selected channel. This is will loop DTE data back towards the DTE interface in addition to passing it on to the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable-loopback-mode(1), disable-loopback-mode(2)

ty1250DiagDteV54Lpbk		1.3.6.1.4.1.466.3.12.6
This selection displays the status of the DTE Channel V.54 Loopback for the channel. This loopback is initiated by the remote node, causing this node to loop data back to the remote node.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	loopback-enable(1), loopback-disable(2)

ty1250DiagDteRmtV54Lpbk		1.3.6.1.4.1.466.3.12.13
This selection controls the DTE Channel V.54 Remote Loopback. Transmit-code-enable (3) will cause the node to transmit a V.54 code to the remote node which will then loop received data back to this node. transmit-code-disable (4) will transmit the disable code.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	transmit-code-enable(3), transmit-code-disable(4)

ty1250DiagDteBerState		1.3.6.1.4.1.466.3.12.7
BERT test related actions: a: Starts a BERT test on a channel, b: Stops a BERT test on a channel, c: Inject Errors while the BERT test is running, d: Clears BERT test errors.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	start-bert-test(1), stop-bert-test(2), inject-error-bert-test(3), clear-error-bert-test(4)

ty1250DiagDteBerStatus		1.3.6.1.4.1.466.3.12.8
Displays the current BERT test sync status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bert-off(1), bert-out-of-sync(2), bert-in-sync(3)

ty1250DiagDteBerErrors		1.3.6.1.4.1.466.3.12.9
Displays the number of errors detected in Bert Test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ty1250DiagDteBerErrSec		1.3.6.1.4.1.466.3.12.10
Displays the number of seconds containing errors in BERT Test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ty1250DiagDteBerTimeElaps		1.3.6.1.4.1.466.3.12.11
Elapsed time since BERT test was started or cleared.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

ty1250DiagDteBerResyncs		1.3.6.1.4.1.466.3.12.12
Displays the number of times BERT test has synched up on the pattern.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

ty1250StatsDteTable		1.3.6.1.4.1.466.3.15
OBJECT IDENTIFIER

ty1250StatsDteTxByteCount		1.3.6.1.4.1.466.3.15.1
The statistic counting the number of bytes transmitted on the DTE channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsDteRxByteCount		1.3.6.1.4.1.466.3.15.2
The statistic counting the number of bytes received on the DTE channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsDteClearStats		1.3.6.1.4.1.466.3.15.3
Allows the user to zero out all the statistics in the DTE statistics table.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	clear-statistics(1)

ty1250StatsNetTable		1.3.6.1.4.1.466.3.16
OBJECT IDENTIFIER

ty1250StatsNetLoopLength		1.3.6.1.4.1.466.3.16.1
The statistic that estimates line attentuation on the network channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsNetBpvCount		1.3.6.1.4.1.466.3.16.2
The statistic counting the number of BPV errors on the network channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsNetTxByteCount		1.3.6.1.4.1.466.3.16.3
The statistic counting the number of bytes transmitted on the network channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsNetRxByteCount		1.3.6.1.4.1.466.3.16.4
The statistic counting the number of bytes received on the network channel.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ty1250StatsNetClearStats		1.3.6.1.4.1.466.3.16.5
Allows the user to zero out all the statistics in the network statistics table.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	clear-statistics(1)

ty1250AlarmType		1.3.6.1.4.1.466.3.13
The type of alarms that are generated on the node
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	line-failure(1), line-in-service(2), connected(3), connect-failure(4), incoming-call(5), disconnected(6), bad-config-in-set(7), config-local-update(8), bpv-threshold-exceeded(9), bpv-threshold-acceptable(10), local-unit-loopback-enabled(11), local-unit-loopback-disabled(12), local-network-loopback-enabled(13), local-network-loopback-disabled(14), remote-network-simplex-loopback-enabled(15), remote-network-simplex-loopback-disabled(16), remote-network-non-latching-loopback-enabled(17), remote-network-non-latching-loopback-disabled(18), v54-loop-up-initiated(19), v54-loop-down-completed(20), v54-loopback-enabled-by-remote(21), v54-loopback-disabled-by-remote(22), bert-test-pattern-initiated(23), bert-test-pattern-completed(24), local-dte-loopback-enabled(25), local-dte-loopback-disabled(26), local-unit-loopback-failure(27), local-network-loopback-failure(28), bert-test-pattern-failure(29), local-dte-loopback-failure(30), v54-loopback-failure(31)

ty1250Trap		0
A ty1250Trap trap signifies that the sending node had its `ty1250AlarmType` variable modified.
TRAP-TYPE

ty1250LineFailureTrap		1
The line has failed.
TRAP-TYPE

ty1250LineInServiceTrap		2
The line is back in service.
TRAP-TYPE

ty1250ConnectedTrap		3
The 1250 unit is connected.
TRAP-TYPE

ty1250ConnectFailureTrap		4
The attempted connection failed.
TRAP-TYPE

ty1250IncomingCallTrap		5
Incoming call.
TRAP-TYPE

ty1250DisconnectedTrap		6
Disconnected.
TRAP-TYPE

ty1250BadConfigTrap		7
The configuration specified in the SET command was bad. SET failed.
TRAP-TYPE

ty1250LocalConfigTrap		8
The configuration has been changed by a means other than SNMP.
TRAP-TYPE

ty1250BPVThresholdExceededTrap		9
BPV threshold exceeded.
TRAP-TYPE

ty1250BPVThresholdAcceptableTrap		10
BPV threshold acceptable.
TRAP-TYPE

ty1250LocalUnitLoopbackEnabledTrap		11
Local unit loopback enabled.
TRAP-TYPE

ty1250LocalUnitLoopbackDisabledTrap		12
Local unit loopback disabled.
TRAP-TYPE

ty1250LocalNetLoopbackEnabledTrap		13
Local network loopback enabled.
TRAP-TYPE

ty1250LocalNetLoopbackDisabledTrap		14
Local network loopback disabled.
TRAP-TYPE

ty1250SimplexCurrentLoopbackEnabledTrap		15
Simplex current loopback enabled.
TRAP-TYPE

ty1250SimplexCurrentLoopbackDisabledTrap		16
Simplex current loopback disabled.
TRAP-TYPE

ty1250NonLatchingLoopbackEnabledTrap		17
Nonlatching loopback enabled.
TRAP-TYPE

ty1250NonLatchingLoopbackDisabledTrap		18
Nonlatching loopback disabled.
TRAP-TYPE

ty1250V54LoopUpInitiatedTrap		19
Starting to loop up a V54 loopback on the remote unit.
TRAP-TYPE

ty1250V54LoopDownCompletedTrap		20
Completed the loop down of a V54 loopback on the remote unit.
TRAP-TYPE

ty1250V54LoopbackEnabledTrap		21
V54 loopback enabled by remote unit.
TRAP-TYPE

ty1250V54LoopbackDisabledTrap		22
V54 loopback disabled by remote unit.
TRAP-TYPE

ty1250BertInitiatedTrap		23
BERT test pattern initiated.
TRAP-TYPE

ty1250BertCompletedTrap		24
BERT test pattern completed.
TRAP-TYPE

ty1250LocalDteLoopbackEnabledTrap		25
Local DTE loopback enabled.
TRAP-TYPE

ty1250LocalDteLoopbackDisabledTrap		26
Local DTE loopback disabled.
TRAP-TYPE

ty1250LocalUnitLoopbackFailedTrap		27
Unable to do a local unit loopback.
TRAP-TYPE

ty1250LocalNetLoopbackFailedTrap		28
Unable to do a local network loopback.
TRAP-TYPE

ty1250BertFailedTrap		29
Unable to do a BERT.
TRAP-TYPE

ty1250LocalDteLoopbackFailedTrap		30
Unable to do a local DTE loopback.
TRAP-TYPE

ty1250V54LoopbackFailedTrap		31
Unable to do a V54 loopback.
TRAP-TYPE

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor