Unisphere-Data-AAA-MIB

File: Unisphere-Data-AAA-MIB.mib (85190 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
Unisphere-Data-MIBs Unisphere-Data-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
IpAddress Counter32 Unsigned32
Gauge32 TEXTUAL-CONVENTION DisplayString
RowStatus TruthValue MODULE-COMPLIANCE
OBJECT-GROUP usDataMibs UsdName

Defined Types

UsdAaaDomainName  
The name of an internet domain. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..63)  

UsdAaaAuthenticationMethods  
The set of configurable authentication choices. The maximum enumerated type will never be greater than 255.
TEXTUAL-CONVENTION    
  INTEGER protocolRadius(1), protocolNone(4), protocolLine(5)  

UsdAaaAccountingMethods  
The set of configurable accounting choices.
TEXTUAL-CONVENTION    
  INTEGER protocolRadius(1), protocolNone(4)  

UsdAddressAssignType  
The set of possible AAA address assignment sources.
TEXTUAL-CONVENTION    
  INTEGER none(0), radius(1), localPool(2), dhcp(3), user(4)  

UsdSubscriberState  
The set of possible AAA subscriber states, expressed as a bit map: init Initial state (transient) pending Auth/Acct or Addr Request is pending established Subscriber is authenticated deleting Deletion of subscriber is pending tunneling Subscriber is being tunneled tunnelAcct Tunnel accounting is enabled terminated Subscriber has been terminated More than one state bit can be active simultaneously. If no bits are set, the subscriber is in a transient initial state.
TEXTUAL-CONVENTION    
  BITS pending(0), established(1), deleting(2), tunneling(3), tunnelAcct(4), terminated(5)  

UsdSubscriberClientType  
The set of possible AAA subscriber client types: ppp PPP client login Command line interface or SSH ip IP-based application config Locally configured client identity tunnel Tunnel e.g. L2TP other Unspecified client type
TEXTUAL-CONVENTION    
  INTEGER ppp(0), login(1), ip(2), config(3), tunnel(4), other(5)  

UsdSubscriberLocationType  
Describes the platform-dependent interpretation of a UsdSubscriberLocationValue object: unknown Unspecified/unknown slotPort Two octets in length; first octet is 'slot', second octet is 'port'
TEXTUAL-CONVENTION    
  INTEGER unknown(0), slotPort(1)  

UsdSubscriberLocationValue  
The value of a platform-dependent interface location, represented as an OCTET STRING. A corresponding UsdSubscriberLocationType object will identify the mapping of octets to location elements, e.g. 'slot.port'. Note, when the value of an object having this syntax is encoded as a MIB table INDEX, the rules for encoding a variable-length OCTET STRING are observed.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..16)  

UsdAaaAssignDomainEntry  
SEQUENCE    
  usdAaaAssignDomainName UsdAaaDomainName
  usdAaaAssignDomainRowStatus RowStatus
  usdAaaAssignDomainRouterName UsdName
  usdAaaAssignDomainLoopback Integer32
  usdAaaAssignDomainIpHint TruthValue
  usdAaaAssignDomainAtmServiceLevel INTEGER
  usdAaaAssignDomainAtmPcr Integer32
  usdAaaAssignDomainAtmScr Integer32
  usdAaaAssignDomainAtmMbs Integer32
  usdAaaAssignDomainOverrideUserName DisplayString
  usdAaaAssignDomainOverridePassword OCTET STRING
  usdAaaAssignDomainStripDomain TruthValue

UsdAaaAssignDomainTunnelEntry  
SEQUENCE    
  usdAaaAssignDomainTunnelName UsdAaaDomainName
  usdAaaAssignDomainTunnelTag INTEGER
  usdAaaAssignDomainTunnelPreference INTEGER
  usdAaaAssignDomainTunnelType INTEGER
  usdAaaAssignDomainTunnelMedium INTEGER
  usdAaaAssignDomainTunnelAddress DisplayString
  usdAaaAssignDomainTunnelPassword DisplayString
  usdAaaAssignDomainTunnelId DisplayString
  usdAaaAssignDomainTunnelHostName DisplayString
  usdAaaAssignDomainTunnelRowStatus RowStatus
  usdAaaAssignDomainTunnelServerName DisplayString
  usdAaaAssignDomainTunnelClientAddress DisplayString

UsdAaaSubscriberEntry  
SEQUENCE    
  usdAaaSubscriberHandle Unsigned32
  usdAaaSubscriberUserName DisplayString
  usdAaaSubscriberRouterName UsdName
  usdAaaSubscriberRouterIndex Unsigned32
  usdAaaSubscriberLoginTime DisplayString
  usdAaaSubscriberIpAddress IpAddress
  usdAaaSubscriberIpAddressMask IpAddress
  usdAaaSubscriberAddrAssignType UsdAddressAssignType
  usdAaaSubscriberInterfaceId DisplayString
  usdAaaSubscriberState UsdSubscriberState
  usdAaaSubscriberClientType UsdSubscriberClientType
  usdAaaSubscriberIngressPolicyName DisplayString
  usdAaaSubscriberEgressPolicyName DisplayString
  usdAaaSubscriberQosProfileName DisplayString
  usdAaaSubscriberRowStatus RowStatus

UsdAaaSubscriberRouterSummaryEntry  
SEQUENCE    
  usdAaaSubscriberRouterSummaryRouterIndex Unsigned32
  usdAaaSubscriberRouterSummaryCount Gauge32

UsdAaaSubscriberRouterEntry  
SEQUENCE    
  usdAaaSubscriberRouterRouterIndex Unsigned32
  usdAaaSubscriberRouterHandle Unsigned32
  usdAaaSubscriberRouterRowStatus RowStatus

UsdAaaSubscriberLocationSummaryEntry  
SEQUENCE    
  usdAaaSubscriberLocationSummaryLocationIndex UsdSubscriberLocationValue
  usdAaaSubscriberLocationSummaryCount Gauge32

UsdAaaSubscriberLocationEntry  
SEQUENCE    
  usdAaaSubscriberLocationLocationIndex UsdSubscriberLocationValue
  usdAaaSubscriberLocationHandle Unsigned32
  usdAaaSubscriberLocationRowStatus RowStatus

Defined Values

usdAaaMIB 1.3.6.1.4.1.4874.2.2.20
The Authentication, Authorization and Accounting (AAA) MIB for the Unisphere Networks enterprise.
MODULE-IDENTITY    

usdAaaObjects 1.3.6.1.4.1.4874.2.2.20.1
OBJECT IDENTIFIER    

usdAaaAssignment 1.3.6.1.4.1.4874.2.2.20.1.1
OBJECT IDENTIFIER    

usdAaaAuthentication 1.3.6.1.4.1.4874.2.2.20.1.2
OBJECT IDENTIFIER    

usdAaaAccounting 1.3.6.1.4.1.4874.2.2.20.1.3
OBJECT IDENTIFIER    

usdAaaAddress 1.3.6.1.4.1.4874.2.2.20.1.4
OBJECT IDENTIFIER    

usdAaaStatistics 1.3.6.1.4.1.4874.2.2.20.1.5
OBJECT IDENTIFIER    

usdAaaTimeout 1.3.6.1.4.1.4874.2.2.20.1.6
OBJECT IDENTIFIER    

usdAaaTunnel 1.3.6.1.4.1.4874.2.2.20.1.7
OBJECT IDENTIFIER    

usdAaaSubscribers 1.3.6.1.4.1.4874.2.2.20.1.8
OBJECT IDENTIFIER    

usdAaaCapabilities 1.3.6.1.4.1.4874.2.2.20.1.9
OBJECT IDENTIFIER    

usdAaaAssignGeneral 1.3.6.1.4.1.4874.2.2.20.1.1.1
OBJECT IDENTIFIER    

usdAaaAssignBrasLicense 1.3.6.1.4.1.4874.2.2.20.1.1.1.1
The license string that determines the system-wide maximum number of remote user connections allowed. A zero-length string (no license) prohibits remote user connections.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

usdAaaAssignBrasLicensedUsers 1.3.6.1.4.1.4874.2.2.20.1.1.1.2
The system-wide maximum number of remote user connections allowed by the currently configured license string.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdAaaAssignDomainDelimiters 1.3.6.1.4.1.4874.2.2.20.1.1.1.3
The list of delimiters used to separate the user's name from the user's domain in the username field. The default is '@'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

usdAaaAssignRealmDelimiters 1.3.6.1.4.1.4874.2.2.20.1.1.1.4
The list of delimiters used to separate the user's name from the user's realm in the username field. The realm is treated like the domain in the ERX. The default is none.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

usdAaaAssignDomainParseOrder 1.3.6.1.4.1.4874.2.2.20.1.1.1.5
The order in which the user's name is parsed: either search for domain first or realm first in the form (realm/user@domain.com). The default is domain first.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER domainFirst(1), realmFirst(2)  

usdAaaAssignSubscriberLimit 1.3.6.1.4.1.4874.2.2.20.1.1.1.6
The maximum number of subscribers permitted in this VR context. The value '0' means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..32000  

usdAaaAssignDomain 1.3.6.1.4.1.4874.2.2.20.1.1.2
OBJECT IDENTIFIER    

usdAaaAssignDomainTable 1.3.6.1.4.1.4874.2.2.20.1.1.2.1
The entries in this table specify the assignment of a remote access user to a virtual router, based on the user's domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaAssignDomainEntry

usdAaaAssignDomainEntry 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1
A specification of the virtual router to which users on a specified domain should be assigned.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaAssignDomainEntry  

usdAaaAssignDomainName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.1
The domain name uniquely identifying this entry.
Status: current Access: read-only
OBJECT-TYPE    
  UsdAaaDomainName  

usdAaaAssignDomainRowStatus 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.2
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAaaAssignDomainRouterName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.3
The name of the virtual router to which remote access users within this domain are assigned.
Status: current Access: read-create
OBJECT-TYPE    
  UsdName  

usdAaaAssignDomainLoopback 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.4
The number of the loopback interface, associated with the specified virtual router, whose IP address is used as the source address when transmitting IP packets on unnumbered remote access user links. For example, if the associated loopback interface for this domain/router was configured via the console as 'loopback 2', this object would contain the integer value 2. A value of -1 indicates the loopback interface is unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -1..32000  

usdAaaAssignDomainIpHint 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.5
Enables/disables the IP hint feature, which causes the system to allocate an IP address before going to RADIUS for authentication.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAaaAssignDomainAtmServiceLevel 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.6
The Service category for this circuit: ubr Unspecified bit rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable Bit Rate. cbr Constant bit rate. Set the service level in combination of the traffic attributes PCR/SCR/MBS in the following matrix for successfull configurations. ServiceLevel PCR SCR MBS ------------------------------------------ ubr omit omit omit ubrPcr must omit omit nrtVbr must must must cbr must omit omit
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), ubr(1), ubrPcr(2), nrtVbr(3), cbr(4)  

usdAaaAssignDomainAtmPcr 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.7
Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when usdAaaAssignDomainAtmServiceLevel is configured to have one of the following values: ubrPcr nrtVbr cbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAaaAssignDomainAtmScr 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.8
Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when usdAaaAssignDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAaaAssignDomainAtmMbs 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.9
Maximum Burst Size, in cells, of this circuit. This parameter is only required when usdAaaAssugbDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAaaAssignDomainOverrideUserName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.10
The override user name associated with this entry. This object is used to override the username of the remote client.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaAssignDomainOverridePassword 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.11
The override password for the user name defined by usdAaaAssignDomainOverrideUserName. This object is used to override the password part of the username/password pair of the remote client. This value returns a string length of 0 on reads for security reasons.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdAaaAssignDomainStripDomain 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.12
Enables/disables the domain name stripping feature, which causes the system to strip the domain name before sending the access-request to RADIUS for authentication.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAaaAssignDomainTunnelTable 1.3.6.1.4.1.4874.2.2.20.1.1.2.2
The entries in this table specify the tunnels associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaAssignDomainTunnelEntry

usdAaaAssignDomainTunnelEntry 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1
A specification of the tunnels associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaAssignDomainTunnelEntry  

usdAaaAssignDomainTunnelName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.1
The domain name associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  UsdAaaDomainName  

usdAaaAssignDomainTunnelTag 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.2
The tunnel tag value associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..31  

usdAaaAssignDomainTunnelPreference 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.3
The tunnel's preference value associated with this entry. The value 0 is the highest preference.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..2000  

usdAaaAssignDomainTunnelType 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.4
The tunnel type associated with this entry. Attempts to set this object to tunnelUnknown(2) will fail (wrongValue).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelL2tp(1), tunnelUnknown(2), tunnelL2f(3)  

usdAaaAssignDomainTunnelMedium 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.5
The tunnel medium associated with this entry. The medium dictates the format of the tunnel address. Attempts to set this object to tunnelMediumUnknown(2) will fail (wrongValue).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelMediumIPv4(1), tunnelMediumUnknown(2)  

usdAaaAssignDomainTunnelAddress 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.6
The tunnel server address associated with this entry. The usdAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaAssignDomainTunnelPassword 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.7
The tunnel password associated with this entry. The object returns a null length string on reads due to security concerns.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaAssignDomainTunnelId 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.8
The tunnel identifier associated with this entry. The tunnel identifier is used to distinguish between multiple tunnels to the same usdAaaAssignDomainTunnelAddress.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaAssignDomainTunnelHostName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.9
The tunnel client hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Client-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

usdAaaAssignDomainTunnelRowStatus 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.10
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAaaAssignDomainTunnelServerName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.11
The tunnel server hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Server-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

usdAaaAssignDomainTunnelClientAddress 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.12
The tunnel client address associated with this entry. The usdAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaAuthGeneral 1.3.6.1.4.1.4874.2.2.20.1.2.1
OBJECT IDENTIFIER    

usdAaaAuthMethods 1.3.6.1.4.1.4874.2.2.20.1.2.1.1
The set of authentication protocols configured on this system. Each octet in this object contains one of the values defined in the UsdAaaAuthenticationMethods TEXTUAL-CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding authentication protocol defined by UsdAaaAuthenticationMethods. Note that if the octet is set to: protocolNone(4) Then authentication does not take place. If an authentication protocol is configured and attempts to reach the authentication server fail, the system will move to the next octet in this object and retry the authentication in the form dictated by the corresponding authentication protocoltype. The process of sequencing thru each octet will stop if the authentication server is successfully contacted, or there are no more configured octets in this object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

usdAaaAcctGeneral 1.3.6.1.4.1.4874.2.2.20.1.3.1
OBJECT IDENTIFIER    

usdAaaAcctInterval 1.3.6.1.4.1.4874.2.2.20.1.3.1.1
The interval that must elapse between generation of accounting reports, ranging from 10 minutes to 18 hours, or disabled if set to zero.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 600..86400  

usdAaaAcctDupServerRouterName 1.3.6.1.4.1.4874.2.2.20.1.3.1.2
The name of another router on this system to which accounting reports should be sent, in addition to or instead of sending accounting reports to the accounting service (if any) configured on the current router (i.e., the router context within which this object instance exists). A zero-length name disables this mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  UsdName  

usdAaaAcctMethods 1.3.6.1.4.1.4874.2.2.20.1.3.1.3
The set of accounting protocols configured on this system. Each octet in this object contains one of the values defined in the UsdAaaAccountingMethods TEXTUAL CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding accounting protocol defined by UsdAaaAccountingMethods. Note that if the octet is set to: protocolNone(4) Then accounting is disabled. If an accounting protocol is configured and reports are not successfully generated, the system will move to the next octet in this object and repeat the attempt to generate an accounting report in the form dictated by the corresponding accounting protocol type. The process of sequencing thru each octet will stop if accounting reports are either successfully generated, or there are no more configured octets in this object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

usdAaaAcctSendStopOnAaaDeny 1.3.6.1.4.1.4874.2.2.20.1.3.1.4
Enables/disables the accounting stop message sent to the accounting server when authentication server grants access, but AAA denies access.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdAaaAcctSendStopOnAaaReject 1.3.6.1.4.1.4874.2.2.20.1.3.1.5
Enables/disables the accounting stop message sent to the accounting server when authentication server denies access.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdAaaAddrGeneral 1.3.6.1.4.1.4874.2.2.20.1.4.1
OBJECT IDENTIFIER    

usdAaaAddrPoolDefault 1.3.6.1.4.1.4874.2.2.20.1.4.1.1
Identifies the default source of IP address allocation for remote access links: none No address source is specified. Using this setting allows the remote PPP subscriber (client) to set it's own address. local Use the local address pool named 'default'. dhcp Use DHCP service.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), local(1), dhcp(2)  

usdAaaDupAddrCheck 1.3.6.1.4.1.4874.2.2.20.1.4.1.2
Enables/disables the duplicate IP address checking which causes the system to check the route table for the PPP user's dynamic IP address is provided to PPP (from AAA).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdAaaAddrNameServer 1.3.6.1.4.1.4874.2.2.20.1.4.2
OBJECT IDENTIFIER    

usdAaaAddrDns 1.3.6.1.4.1.4874.2.2.20.1.4.2.1
OBJECT IDENTIFIER    

usdAaaAddrWins 1.3.6.1.4.1.4874.2.2.20.1.4.2.2
OBJECT IDENTIFIER    

usdAaaAddrDnsPrimary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.1
The IP address of the primary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

usdAaaAddrDnsSecondary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.2
The IP address of the secondary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

usdAaaAddrWinsPrimary 1.3.6.1.4.1.4874.2.2.20.1.4.2.2.1
The IP address of the primary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

usdAaaAddrWinsSecondary 1.3.6.1.4.1.4874.2.2.20.1.4.2.2.2
The IP address of the secondary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

usdAaaTimeoutGeneral 1.3.6.1.4.1.4874.2.2.20.1.6.1
OBJECT IDENTIFIER    

usdAaaIdleTimeout 1.3.6.1.4.1.4874.2.2.20.1.6.1.1
The maximum number of seconds that a user session can be idle before system disconnects the user, ranging from 300 to 7200 seconds, 0 disables idle timeout.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 300..7200  

usdAaaSessionTimeout 1.3.6.1.4.1.4874.2.2.20.1.6.1.2
The maximum number of seconds that a user session can be established before system disconnects the user, ranging from 60 to 604800 seconds, 0 disables session timeout.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 60..1814400  

usdAaaTunnelGeneral 1.3.6.1.4.1.4874.2.2.20.1.7.1
OBJECT IDENTIFIER    

usdAaaTunnelClientName 1.3.6.1.4.1.4874.2.2.20.1.7.1.1
The default tunnel client hostname associated with this virtual router. This object is used when no tunnel client name (client auth ID) is supplied in the authentication response.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

usdAaaTunnelPassword 1.3.6.1.4.1.4874.2.2.20.1.7.1.2
The default tunnel password associated with this virtual router. This object is used when no tunnel password is supplied in the authentication response. The object returns a null length string on reads due to security concerns.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdAaaTunnelNasPortMethod 1.3.6.1.4.1.4874.2.2.20.1.7.1.3
The default tunnel NAS-port method associated with this virtual router. This object is used to specify the LAC's NAS-port method. This provides limit compatiability to Cisco LNS for the NAS-port method AVP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), ciscoAvp(1)  

usdAaaTunnelIgnoreNasPort 1.3.6.1.4.1.4874.2.2.20.1.7.1.4
Enables/disables the use of the NAS-port value that is passed in from the tunnel application.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdAaaTunnelIgnoreNasPortType 1.3.6.1.4.1.4874.2.2.20.1.7.1.5
Enables/disables the use of the NAS-port-type value that is passed in from the tunnel application.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdAaaTunnelAssignmentIdFormat 1.3.6.1.4.1.4874.2.2.20.1.7.1.6
The tunnel assignment ID format for distinguishing tunnel definitions. This object is used to specify the tunnel assigment ID format passed to the LAC. The value assignmentId(0) indicates that the original tunnel assignment ID value is to be used; clientServerId(1) indicates that the concatenated value from client-auth-name, server-auth-name, and assignment-id is to be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER assignmentId(0), clientServerId(1)  

usdAaaIncomingInitiateRequests 1.3.6.1.4.1.4874.2.2.20.1.5.1
The number of AAA incoming initiate requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingTerminateRequests 1.3.6.1.4.1.4874.2.2.20.1.5.2
The number of AAA incomining termination requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingTunnelGrantResponses 1.3.6.1.4.1.4874.2.2.20.1.5.3
The number of AAA outgoing tunnel grant responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingGrantResponses 1.3.6.1.4.1.4874.2.2.20.1.5.4
The number of AAA outgoing grant responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingDenyResponses 1.3.6.1.4.1.4874.2.2.20.1.5.5
The number of AAA outgoing deny responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingErrorResponses 1.3.6.1.4.1.4874.2.2.20.1.5.6
The number of AAA outgoing error responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingAuthRequests 1.3.6.1.4.1.4874.2.2.20.1.5.7
The number of AAA outgoing authentication requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingAuthResponses 1.3.6.1.4.1.4874.2.2.20.1.5.8
The number of AAA incoming authentication responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingReAuthRequests 1.3.6.1.4.1.4874.2.2.20.1.5.9
The number of AAA outgoing re-authentication requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingReAuthResponses 1.3.6.1.4.1.4874.2.2.20.1.5.10
The number of AAA incoming re-authentication responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingAcctRequests 1.3.6.1.4.1.4874.2.2.20.1.5.11
The number of AAA outgoing accounting requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingAcctResponses 1.3.6.1.4.1.4874.2.2.20.1.5.12
The number of AAA incoming accounting responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingDupAcctRequests 1.3.6.1.4.1.4874.2.2.20.1.5.13
The number of AAA outgoing duplicate accounting requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingDupAcctResponses 1.3.6.1.4.1.4874.2.2.20.1.5.14
The number of AAA incoing duplication accounting responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaOutgoingAddrRequests 1.3.6.1.4.1.4874.2.2.20.1.5.15
The number of AAA outgoing address requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaIncomingAddrResponses 1.3.6.1.4.1.4874.2.2.20.1.5.16
The number of AAA incoming address responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAaaSubscriberMaxCount 1.3.6.1.4.1.4874.2.2.20.1.8.1
The configuration setting for the maximum number of subscribers. There is a grace number of subscribers above this limit, which when reached will cause authentication requests to be denied.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdAaaSubscriberPeakCount 1.3.6.1.4.1.4874.2.2.20.1.8.2
The peak number of subscribers. The peak count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaSubscriberCount 1.3.6.1.4.1.4874.2.2.20.1.8.3
The current number of subscribers. The subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaSubscriberTable 1.3.6.1.4.1.4874.2.2.20.1.8.4
The entries in this table represent subscribers by subscriber handle value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaSubscriberEntry

usdAaaSubscriberEntry 1.3.6.1.4.1.4874.2.2.20.1.8.4.1
A specification of subscribers by subscriber handle.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaSubscriberEntry  

usdAaaSubscriberHandle 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.1
The subscriber handle associated with this subscriber. A subscriber handle is a monotomically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberUserName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.2
The RADIUS userName associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberRouterName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.3
The virtual router assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  UsdName  

usdAaaSubscriberRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.4
The router index that identifies the virtual router associated with this subscriber. The value of this object can be used to index the router in the usdRouterTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberLoginTime 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.5
The time this subscriber logged in to RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberIpAddress 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.6
The client IP Address assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdAaaSubscriberIpAddressMask 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.7
The client IP Address Mask assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdAaaSubscriberAddrAssignType 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.8
The address assignment type for this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  UsdAddressAssignType  

usdAaaSubscriberInterfaceId 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.9
A text string describing the local interface associated with this subscriber. Types/formats/examples for this string include: ATM Virtual Circuit atm /:. 'atm 3/0:0.100' Ethernet { fastEthernet | gigabitEthernet } / 'fastEthernet 3/0' 'gigabitEthernet 3/0' Ethernet VLAN { fastEthernet | gigabitEthernet } /: 'fastEthernet 3/0:1000' 'gigabitEthernet 3/0:1000' Channelized Serial serial /:[/]* 'serial 3/0:4' (T1/E1) 'serial 3/0:2/4' (T3/E3) 'serial 3/0:2/1/1/4' (OC3/OC12 - channelized DS3) 'serial 3/0:2/1/1/1/4' (OC3/OC12 - virtual tributaries) L2TP/L2F over IP ip::::: :: 'ip:10.10.0.1:20.20.0.2:1234:5678:9abc:def0:6789abcd' (Note: tunnelIDs, sessionIDs, and callSerialNumber are in hexadecimal.) Other formats may be supported over time.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberState 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.10
The state of this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  UsdSubscriberState  

usdAaaSubscriberClientType 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.11
The client type for this subscriber. Certain client types (e.g., 'other') might be suppressed from representation in this table.
Status: current Access: read-only
OBJECT-TYPE    
  UsdSubscriberClientType  

usdAaaSubscriberIngressPolicyName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.12
The Ingress Policy Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberEgressPolicyName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.13
The Egress Policy Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberQosProfileName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.14
The QoS Profile Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdAaaSubscriberRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.15
Controls the deletion of the subscriber from this table. Deletion of the subscriber is analogous to logging the subscriber out of the network. Note: only 'destroy' is supported for SNMP SET operations.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

usdAaaSubscriberRouterSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.5
The entries in this table report number of subscribers per router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaSubscriberRouterSummaryEntry

usdAaaSubscriberRouterSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.5.1
A specification of subscribers for a router.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaSubscriberRouterSummaryEntry  

usdAaaSubscriberRouterSummaryRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.5.1.1
The router index of the virtual router. The value of this object can be used to retrieve additional information in the router mib.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberRouterSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.5.1.2
The number of subscribers on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaSubscriberRouterTable 1.3.6.1.4.1.4874.2.2.20.1.8.6
The entries in this table sort subscribers by router ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaSubscriberRouterEntry

usdAaaSubscriberRouterEntry 1.3.6.1.4.1.4874.2.2.20.1.8.6.1
A specification of subscribers by router ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaSubscriberRouterEntry  

usdAaaSubscriberRouterRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.1
The router index of the virtual router. The value of this object can be used to retrieve additional information in the router MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberRouterHandle 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.2
The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberRouterRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.3
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

usdAaaSubscriberLocationType 1.3.6.1.4.1.4874.2.2.20.1.8.7
Describes the interpretation of UsdSubscriberLocationValue object values into platform-dependent interface location components, e.g., 'slot.port'.
Status: current Access: read-only
OBJECT-TYPE    
  UsdSubscriberLocationType  

usdAaaSubscriberLocationSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.8
The entries in this table report number of subscribers per interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaSubscriberLocationSummaryEntry

usdAaaSubscriberLocationSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.8.1
A specification of subscribers on an interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaSubscriberLocationSummaryEntry  

usdAaaSubscriberLocationSummaryLocationIndex 1.3.6.1.4.1.4874.2.2.20.1.8.8.1.1
The value of a platform interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdSubscriberLocationValue  

usdAaaSubscriberLocationSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.8.1.2
The number of subscribers associated with this interface location.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaSubscriberLocationTable 1.3.6.1.4.1.4874.2.2.20.1.8.9
The entries in this table sort subscribers by interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAaaSubscriberLocationEntry

usdAaaSubscriberLocationEntry 1.3.6.1.4.1.4874.2.2.20.1.8.9.1
An association of a subscriber to an interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAaaSubscriberLocationEntry  

usdAaaSubscriberLocationLocationIndex 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.1
The value of a platform interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdSubscriberLocationValue  

usdAaaSubscriberLocationHandle 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.2
The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

usdAaaSubscriberLocationRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.3
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

usdAaaSubscriberPseudoPeakCount 1.3.6.1.4.1.4874.2.2.20.1.8.10
The peak number of pseudo-subscribers. The peak count includes successfully authenticated pseudo-subscribers as well as those pseudo-subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Unisphere-Data-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaSubscriberPseudoCount 1.3.6.1.4.1.4874.2.2.20.1.8.11
The current number of pseudo-subscribers. The pseudo-subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Unisphere-Data-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

usdAaaAccountingCapability 1.3.6.1.4.1.4874.2.2.20.1.9.1
Indicates whether this system supports AAA Accounting. The value true(1) indicate that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAaaAddressAssignmentCapability 1.3.6.1.4.1.4874.2.2.20.1.9.2
Indicates whether this system supports AAA address assignment. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAaaBrasCapability 1.3.6.1.4.1.4874.2.2.20.1.9.3
Indicates whether this system supports AAA BRAS functionality. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAaaTunnelingCapability 1.3.6.1.4.1.4874.2.2.20.1.9.4
Indicates whether this system supports AAA tunneling. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAaaMIBConformance 1.3.6.1.4.1.4874.2.2.20.4
OBJECT IDENTIFIER    

usdAaaMIBCompliances 1.3.6.1.4.1.4874.2.2.20.4.1
OBJECT IDENTIFIER    

usdAaaMIBGroups 1.3.6.1.4.1.4874.2.2.20.4.2
OBJECT IDENTIFIER    

usdAaaCompliance 1.3.6.1.4.1.4874.2.2.20.4.1.1
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance2 1.3.6.1.4.1.4874.2.2.20.4.1.2
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added and new groupings were defined.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance3 1.3.6.1.4.1.4874.2.2.20.4.1.3
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the usdAaaAssignDomainStripDomain object was added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance4 1.3.6.1.4.1.4874.2.2.20.4.1.4
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new assignment delimiter objects were added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance5 1.3.6.1.4.1.4874.2.2.20.4.1.5
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the subscriber and capabilities groups were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance6 1.3.6.1.4.1.4874.2.2.20.4.1.6
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when support was added for subscriber information by interface location.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance7 1.3.6.1.4.1.4874.2.2.20.4.1.7
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when several new objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAaaCompliance8 1.3.6.1.4.1.4874.2.2.20.4.1.8
The compliance statement for systems supporting AAA.
Status: current Access: read-only
MODULE-COMPLIANCE    

usdAaaGroup 1.3.6.1.4.1.4874.2.2.20.4.2.1
Obsolete collection of objects providing management of AAA functionality in a Unisphere product. This group became obsolete when new objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.2
Obsolete collection of objects providing management of AAA functionality in a Unisphere product. This group became obsolete when new objects were added and new groupings were defined.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaBasicGroup 1.3.6.1.4.1.4874.2.2.20.4.2.3
The basic collection of objects providing management of AAA functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaBrasGroup 1.3.6.1.4.1.4874.2.2.20.4.2.4
Obsolete collection of objects providing management of AAA B-RAS functionality in a Unisphere product. This group became obsolete when the usdAaaAssignDomainStripDomain object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaTunnelGroup 1.3.6.1.4.1.4874.2.2.20.4.2.5
The collection of objects providing management of AAA tunneling functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaAuthenticationGroup 1.3.6.1.4.1.4874.2.2.20.4.2.6
The collection of objects providing management of AAA authentication functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaAccountingGroup 1.3.6.1.4.1.4874.2.2.20.4.2.7
Obsolete collection of objects providing management of AAA accounting functionality in a Unisphere product. This group became obsolete when the usdAaaAcctSendStopOnAaaDeny object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaAddressGroup 1.3.6.1.4.1.4874.2.2.20.4.2.8
The collection of objects providing management of AAA address assignment functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaBrasGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.9
Obsolete collection of objects providing management of AAA B-RAS functionality in a Unisphere product. This group became obsolete when new assignment delimiter objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaBrasGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.10
Obsolete collection of objects providing management of AAA B-RAS functionality in a Unisphere product. This group became obsolete when new objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaSubscriberGroup 1.3.6.1.4.1.4874.2.2.20.4.2.11
Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Unisphere product. This group became obsolete when support was added for monitoring subscriber information by interface location.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaCapabilitiesGroup 1.3.6.1.4.1.4874.2.2.20.4.2.12
The collection of objects providing management of AAA Capabilities functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaSubscriberGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.13
Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Unisphere product. This group became obsolete when the pseudo-subscriber meters were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAaaAccountingGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.14
The collection of objects providing management of AAA accounting functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaBrasGroup4 1.3.6.1.4.1.4874.2.2.20.4.2.15
The collection of objects providing management of AAA B-RAS functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAaaSubscriberGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.16
The collection of objects providing management of AAA B-RAS Subscriber functionality in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor