Unisphere-Data-ATM-MIB

File: Unisphere-Data-ATM-MIB.mib (106345 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB ATM-TC-MIB ATM-MIB
ATM-FORUM-SNMP-M4-MIB Unisphere-Data-MIBs Unisphere-Data-TC

Imported symbols

MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE
NOTIFICATION-TYPE Integer32 Unsigned32
Counter64 Counter32 IpAddress
TEXTUAL-CONVENTION RowStatus TruthValue
TimeStamp MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP InterfaceIndex InterfaceIndexOrZero
ifIndex AtmVpIdentifier AtmVcIdentifier
AtmVorXAdminStatus AtmAddr atmVplVpi
atmVclVpi atmVclVci atmfM4VpTestObject
atmfM4VpTestId atmfM4VpTestType atmfM4VpTestResult
atmfM4VcTestObject atmfM4VcTestId atmfM4VcTestType
atmfM4VcTestResult usDataMibs UsdNextIfIndex
UsdEnable

Defined Types

UsdAtmNbmaMapName  
An administratively assigned map name. Represents textual information taken from the NVT ASCII character set. The name must be unique per system.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..32)  

UsdAtmNbmaMapNameOrNull  
An administratively assigned map name. Represents textual information taken from the NVT ASCII character set. The name must be unique per system. Differs from UsdAtmNbmaMapName in that it permits a zero-length string.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

UsdAtmIfEntry  
SEQUENCE    
  usdAtmIfIndex InterfaceIndex
  usdAtmIfRowStatus RowStatus
  usdAtmIfLowerIfIndex InterfaceIndexOrZero
  usdAtmIfIlmiVpi AtmVpIdentifier
  usdAtmIfIlmiVci AtmVcIdentifier
  usdAtmIfIlmiVcd Integer32
  usdAtmIfIlmiPollFrequency Integer32
  usdAtmIfIlmiAdminState INTEGER
  usdAtmIfUniVersion INTEGER
  usdAtmIfOamCellRxAdminState INTEGER
  usdAtmIfInCells Counter64
  usdAtmIfOutCells Counter64
  usdAtmIfVcCount INTEGER
  usdAtmIfMapGroup UsdAtmNbmaMapNameOrNull
  usdAtmIfCacAdminState UsdEnable
  usdAtmIfCacUbrWeight Integer32
  usdAtmIfCacSubscriptionBandwidth Integer32
  usdAtmIfCacAvailableBandwidth Integer32
  usdAtmIfOamCellFilter INTEGER
  usdAtmIfCacUsedBandwidthUpper Unsigned32
  usdAtmIfCacUsedBandwidthLower Unsigned32

UsdAtmPvcStatisticsEntry  
SEQUENCE    
  usdAtmPvcStatsIfIndex InterfaceIndex
  usdAtmPvcStatsVpi AtmVpIdentifier
  usdAtmPvcStatsVci AtmVcIdentifier
  usdAtmPvcStatsInCells Counter64
  usdAtmPvcStatsInCellOctets Counter64
  usdAtmPvcStatsInPackets Counter64
  usdAtmPvcStatsInPacketOctets Counter64
  usdAtmPvcStatsOutCells Counter64
  usdAtmPvcStatsOutCellOctets Counter64
  usdAtmPvcStatsOutPackets Counter64
  usdAtmPvcStatsOutPacketOctets Counter64
  usdAtmPvcStatsInCellErrors Counter32
  usdAtmPvcStatsinPacketErrors Counter32
  usdAtmPvcStatsOutCellErrors Counter32
  usdAtmPvcStatsOutPacketErrors Counter32
  usdAtmPvcStatsInPacketDiscards Counter32
  usdAtmPvcStatsInPacketOctetDiscards Counter32
  usdAtmPvcStatsInPacketUnknownProtocol Counter32

UsdAtmVpTunnelEntry  
SEQUENCE    
  usdAtmVpTunnelIfIndex InterfaceIndex
  usdAtmVpTunnelVpi AtmVpIdentifier
  usdAtmVpTunnelKbps Integer32
  usdAtmVpTunnelRowStatus RowStatus
  usdAtmVpTunnelServiceCategory INTEGER

UsdAtmIfCapabilityEntry  
SEQUENCE    
  usdAtmIfCapabilityIndex InterfaceIndex
  usdAtmIfCapabilityTrafficShaping TruthValue
  usdAtmIfCapabilityOam TruthValue
  usdAtmIfCapabilityDefaultVcPerVp INTEGER
  usdAtmIfCapabilityNumVpiVciBits INTEGER
  usdAtmIfCapabilityMaxVcd Integer32
  usdAtmIfCapabilityMaxVpi AtmVpIdentifier
  usdAtmIfCapabilityMaxVci AtmVcIdentifier
  usdAtmIfCapabilityOamCellFilter TruthValue

UsdAtmIfSvcSignallingEntry  
SEQUENCE    
  usdAtmIfSvcSignallingVpi AtmVpIdentifier
  usdAtmIfSvcSignallingVci AtmVcIdentifier
  usdAtmIfSvcSignallingVcd AtmVcIdentifier
  usdAtmIfSvcSignallingAdminStatus AtmVorXAdminStatus

UsdAtmAal5IfEntry  
SEQUENCE    
  usdAtmAal5IfIndex InterfaceIndex
  usdAtmAal5IfRowStatus RowStatus
  usdAtmAal5IfLowerIfIndex InterfaceIndexOrZero

UsdAtmSubIfEntry  
SEQUENCE    
  usdAtmSubIfIndex InterfaceIndex
  usdAtmSubIfRowStatus RowStatus
  usdAtmSubIfDistinguisher Integer32
  usdAtmSubIfLowerIfIndex InterfaceIndexOrZero
  usdAtmSubIfNbma TruthValue
  usdAtmSubIfAddress AtmAddr

UsdAtmSubIfVccEntry  
SEQUENCE    
  usdAtmSubIfVccVpi AtmVpIdentifier
  usdAtmSubIfVccVci AtmVcIdentifier
  usdAtmSubIfVccRowStatus RowStatus
  usdAtmSubIfVccVcd Integer32
  usdAtmSubIfVccType INTEGER
  usdAtmSubIfVccServiceCategory INTEGER
  usdAtmSubIfVccPcr Integer32
  usdAtmSubIfVccScr Integer32
  usdAtmSubIfVccMbs Integer32
  usdAtmSubIfInverseArp TruthValue
  usdAtmSubIfInverseArpRefresh Integer32

UsdAtmCircuitOamEntry  
SEQUENCE    
  usdAtmCircuitOamIfIndex InterfaceIndex
  usdAtmCircuitOamVpi AtmVpIdentifier
  usdAtmCircuitOamVci AtmVcIdentifier
  usdAtmCircuitOamAdminStatus INTEGER
  usdAtmCircuitOamLoopbackOperStatus INTEGER
  usdAtmCircuitVcOamOperStatus INTEGER
  usdAtmCircuitOamLoopbackFrequency Integer32
  usdAtmCircuitInOamF5Cells Counter32
  usdAtmCircuitInOamCellsDropped Counter32
  usdAtmCircuitOutOamF5Cells Counter32
  usdAtmCircuitInOamF5EndToEndLoopbackCells Counter32
  usdAtmCircuitInOamF5SegmentLoopbackCells Counter32
  usdAtmCircuitInOamF5AisCells Counter32
  usdAtmCircuitInOamF5RdiCells Counter32
  usdAtmCircuitOutOamF5EndToEndLoopbackCells Counter32
  usdAtmCircuitOutOamF5SegmentLoopbackCells Counter32
  usdAtmCircuitOutOamF5RdiCells Counter32

UsdAtmSubIfVccTrafficShapingEntry  
SEQUENCE    
  usdAtmSubIfVccTrafficShapingCdvt Unsigned32
  usdAtmSubIfVccTrafficShapingClp0 TruthValue
  usdAtmSubIfVccTrafficShapingTagging TruthValue
  usdAtmSubIfVccTrafficShapingPoliceObserve TruthValue
  usdAtmSubIfVccTrafficShapingPacketShaping TruthValue

UsdAtmSubIfSvcConfigEntry  
SEQUENCE    
  usdAtmSubIfSvcRowStatus RowStatus
  usdAtmSubIfSvcConfigDestAtmAddress AtmAddr
  usdAtmSubIfSvcConfigCircuitType INTEGER
  usdAtmSubIfSvcConfigServiceCategory INTEGER
  usdAtmSubIfSvcConfigPcr Unsigned32
  usdAtmSubIfSvcConfigScr Unsigned32
  usdAtmSubIfSvcConfigMbs Unsigned32
  usdAtmSubIfSvcConfigCdvt Unsigned32
  usdAtmSubIfSvcConfigClp0 TruthValue
  usdAtmSubIfSvcConfigTagging TruthValue
  usdAtmSubIfSvcConfigObserve TruthValue
  usdAtmSubIfSvcConfigPacketDiscard TruthValue

UsdAtmNbmaMapEntry  
SEQUENCE    
  usdAtmNbmaMapName UsdAtmNbmaMapName
  usdAtmNbmaMapVcd Integer32
  usdAtmNbmaMapIpAddress IpAddress
  usdAtmNbmaMapVpi AtmVpIdentifier
  usdAtmNbmaMapVci AtmVcIdentifier
  usdAtmNbmaMapIfIndex InterfaceIndexOrZero
  usdAtmNbmaMapBroadcast TruthValue
  usdAtmNbmaMapRowStatus RowStatus

UsdAtmNbmaMapListEntry  
SEQUENCE    
  usdAtmNbmaMapListName UsdAtmNbmaMapName
  usdAtmNbmaMapListRowStatus RowStatus

UsdAtmVpPingEntry  
SEQUENCE    
  usdAtmVpPingProbeCount Unsigned32
  usdAtmVpPingTimeOut Unsigned32
  usdAtmVpPingCtlTrapGeneration BITS
  usdAtmVpPingSentProbes Unsigned32
  usdAtmVpPingProbeResponses Unsigned32
  usdAtmVpPingStartTime TimeStamp
  usdAtmVpPingMinRtt Unsigned32
  usdAtmVpPingMaxRtt Unsigned32
  usdAtmVpPingAverageRtt Unsigned32

UsdAtmVcPingEntry  
SEQUENCE    
  usdAtmVcPingProbeCount Unsigned32
  usdAtmVcPingTimeOut Unsigned32
  usdAtmVcPingCtlTrapGeneration BITS
  usdAtmVcPingSentProbes Unsigned32
  usdAtmVcPingProbeResponses Unsigned32
  usdAtmVcPingStartTime TimeStamp
  usdAtmVcPingMinRtt Unsigned32
  usdAtmVcPingMaxRtt Unsigned32
  usdAtmVcPingAverageRtt Unsigned32

Defined Values

usdAtmMIB 1.3.6.1.4.1.4874.2.2.8
The ATM MIB for the Unisphere Networks Inc. enterprise.
MODULE-IDENTITY    

usdAtmObjects 1.3.6.1.4.1.4874.2.2.8.1
OBJECT IDENTIFIER    

usdAtmIfLayer 1.3.6.1.4.1.4874.2.2.8.1.1
OBJECT IDENTIFIER    

usdAtmAal5IfLayer 1.3.6.1.4.1.4874.2.2.8.1.2
OBJECT IDENTIFIER    

usdAtmSubIfLayer 1.3.6.1.4.1.4874.2.2.8.1.3
OBJECT IDENTIFIER    

usdAtmNbma 1.3.6.1.4.1.4874.2.2.8.1.4
OBJECT IDENTIFIER    

usdAtmPing 1.3.6.1.4.1.4874.2.2.8.1.5
OBJECT IDENTIFIER    

usdAtmNextIfIndex 1.3.6.1.4.1.4874.2.2.8.1.1.1
Coordinate ifIndex value allocation for entries in usdAtmIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdAtmIfTable 1.3.6.1.4.1.4874.2.2.8.1.1.2
This table contains entries for ATM interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmIfEntry

usdAtmIfEntry 1.3.6.1.4.1.4874.2.2.8.1.1.2.1
Each entry describes the characteristics of an ATM interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmIfEntry  

usdAtmIfIndex 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.1
The ifIndex of the ATM interface. When creating entries in this table, suitable values for this object are determined by reading usdAtmNextIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmIfRowStatus 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdAtmIfRowStatus usdAtmIfLowerIfIndex In addition, when creating an entry the following condition must hold: A value for usdAtmIfIndex must have been determined previously, by reading usdAtmNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created or destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmIfLowerIfIndex 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.3
The ifIndex of an interface over which this ATM interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdAtmIfIlmiVpi 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.4
The VPI of the ILMI of a major ATM interface.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmIfIlmiVci 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.5
The VCI of the ILMI of a major ATM interface.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmIfIlmiVcd 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.6
An integer identifier for the ILMI, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmIfIlmiPollFrequency 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.7
The amount of time in seconds between successive transmissions of ILMI messages on this interface for the purpose of detecting loss of ILMI connectivity. The distinguished value zero disables ILMI connectivity procedures on this interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

usdAtmIfIlmiAdminState 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.8
The administrative status of ILMI in the ATM interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

usdAtmIfUniVersion 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.9
Use to specify the User Network Interface (UNI) the router should use when ILMI link auto determination is unsuccesful or ILMI is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER version3Dot0(0), version3Dot1(1), version4Dot0(2)  

usdAtmIfOamCellRxAdminState 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.10
Use to specify the OAM Cell Receive Administrative state on this interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER oamCellAdminStateDisabled(0), oamCellAdminStateEnabled(1)  

usdAtmIfInCells 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.11
The total number of cells received on this major interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmIfOutCells 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.12
The total number of cells transmitted on this major interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmIfVcCount 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.13
The total number of circuits configured on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..268431360  

usdAtmIfMapGroup 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.14
The NBMA map group this interface is associated with.
Status: current Access: read-create
OBJECT-TYPE    
  UsdAtmNbmaMapNameOrNull  

usdAtmIfCacAdminState 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.15
The administrative staus of CAC on this ATM major interface.
Status: current Access: read-create
OBJECT-TYPE    
  UsdEnable  

usdAtmIfCacUbrWeight 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.16
The bandwidth associated with every UBR and UBR with PCR connection configured on the ATM major interface. This value is used for CAC computation. The units are kilo-bits per second (kbps).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmIfCacSubscriptionBandwidth 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.17
The subscribed bandwidth of the ATM major interface. If this value is not specified or set to 0, the effective port bandwidth is used. When a Get operation is performed the current effective bandwidth is returned. The units are kilo-bits per second (kbps).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmIfCacAvailableBandwidth 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.18
The available bandwidth of the ATM major interface. As connections are added or deleted on the interface, this value is updated. The units are kilo-bits per second (kbps).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmIfOamCellFilter 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.23
The type of OAM cells to discard when usdAtmIfOamCellRxAdminState is set to oamCellAdminStateDisabled. The value oamCellFilterAlarm discards received OAM AIS and RDI cells. The value oamCellFilterAll discards all received OAM cells. Note that when usdAtmIfOamCellRxAdminState is set to oamCellAdminStateEnabled, this object has no effect.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER oamCellFilterAll(0), oamCellFilterAlarm(1)  

usdAtmIfCacUsedBandwidthUpper 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.24
The most significant 32 bits of the CAC used bandwidth on the ATM major interface. The least significant 32 bits of the CAC used bandwidth are specified by usdAtmIfCacUsedBandwidthLower.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmIfCacUsedBandwidthLower 1.3.6.1.4.1.4874.2.2.8.1.1.2.1.25
The least significant 32 bits of the CAC used bandwidth on the ATM major interface. The most significant 32 bits of the CAC used bandwidth are specified by usdAtmIfCacUsedBandwidthUpper.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmPvcStatisticsTable 1.3.6.1.4.1.4874.2.2.8.1.1.3
This table contains statistics for PVC entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmPvcStatisticsEntry

usdAtmPvcStatisticsEntry 1.3.6.1.4.1.4874.2.2.8.1.1.3.1
Each entry provides statistics on an ATM PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmPvcStatisticsEntry  

usdAtmPvcStatsIfIndex 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.1
The ifIndex of the ATM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmPvcStatsVpi 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.2
The VPI of the ATM VCC used by this ATM interface and PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmPvcStatsVci 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.3
The VCI of the ATM VCC used by this ATM interface and PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmPvcStatsInCells 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.4
Received cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsInCellOctets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.5
Received cells octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsInPackets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.6
Received AAL PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsInPacketOctets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.7
Received AAL PDU octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsOutCells 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.8
Transmitted cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsOutCellOctets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.9
Transmitted cell octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsOutPackets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.10
Transmitted AAL PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsOutPacketOctets 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.11
Transmitted AAL PDU octets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

usdAtmPvcStatsInCellErrors 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.12
Received cells dropped due to errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsinPacketErrors 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.13
Received packets dropped due to errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsOutCellErrors 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.14
Cells not transmitted due to errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsOutPacketErrors 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.15
Packets not transmitted due to errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsInPacketDiscards 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.16
Received packets w/o errors discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsInPacketOctetDiscards 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.17
Received bytes w/o errors discarded.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmPvcStatsInPacketUnknownProtocol 1.3.6.1.4.1.4874.2.2.8.1.1.3.1.18
Received packets that are discarded because the interface can not discern or is not configured to support this protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmVpTunnelTable 1.3.6.1.4.1.4874.2.2.8.1.1.4
This table contains entries for ATM VP Tunnels present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmVpTunnelEntry

usdAtmVpTunnelEntry 1.3.6.1.4.1.4874.2.2.8.1.1.4.1
Each entry describes the characteristics of an ATM VP Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmVpTunnelEntry  

usdAtmVpTunnelIfIndex 1.3.6.1.4.1.4874.2.2.8.1.1.4.1.1
The ifIndex of the ATM interface. The value of this object is the same as the usdAtmIfIndex object in the usdAtmIfTable. Entries in this table cannot be created unless the underlying ATM interface entry is created first in the usdAtmIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmVpTunnelVpi 1.3.6.1.4.1.4874.2.2.8.1.1.4.1.2
The VPI value for this VP tunnel entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmVpTunnelKbps 1.3.6.1.4.1.4874.2.2.8.1.1.4.1.3
The tunnel rate in kilobits per second (kbps) for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmVpTunnelRowStatus 1.3.6.1.4.1.4874.2.2.8.1.1.4.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdAtmVpTunnelRowStatus usdAtmVpTunnelKbps In addition, when creating an entry the following condition must hold: A correponding usdAtmVpTunnelIfIndex value must have been created in the usdAtmIfTable previously.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmVpTunnelServiceCategory 1.3.6.1.4.1.4874.2.2.8.1.1.4.1.5
The ATM service category for the tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER nrtVbr(1), cbr(2)  

usdAtmIfCapabilityTable 1.3.6.1.4.1.4874.2.2.8.1.1.5
This table contains entries for ATM interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmIfCapabilityEntry

usdAtmIfCapabilityEntry 1.3.6.1.4.1.4874.2.2.8.1.1.5.1
Each entry describes the capabilities of an ATM interface. A management client can use this table to determine differences in the configurable level of support across entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmIfCapabilityEntry  

usdAtmIfCapabilityIndex 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.1
The ifIndex of the ATM interface. The value of this object is the same as usdAtmIfIndex in the usdAtmIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmIfCapabilityTrafficShaping 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.2
Indicates whether traffic shaping is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAtmIfCapabilityOam 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.3
Indicates whether OAM is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAtmIfCapabilityDefaultVcPerVp 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.4
The default number of VCs per VP for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

usdAtmIfCapabilityNumVpiVciBits 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.5
The total range of bits used for constructing VPI/VCI identifiers for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 8..28  

usdAtmIfCapabilityMaxVcd 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.6
The maximum configurable value for a VCD on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmIfCapabilityMaxVpi 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.7
The maximum configurable value for a VPI on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmIfCapabilityMaxVci 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.8
The maximum configurable value for a VCI on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmIfCapabilityOamCellFilter 1.3.6.1.4.1.4874.2.2.8.1.1.5.1.9
Indicates whether OAM cell filter is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdAtmIfSvcSignallingTable 1.3.6.1.4.1.4874.2.2.8.1.1.6
This table contains entries for extending the usdAtmIfTable for configuring signalling information for switched virtual connection (SVC).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmIfSvcSignallingEntry

usdAtmIfSvcSignallingEntry 1.3.6.1.4.1.4874.2.2.8.1.1.6.1
Each entry provides configuration parameters for ATM signalling on the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmIfSvcSignallingEntry  

usdAtmIfSvcSignallingVpi 1.3.6.1.4.1.4874.2.2.8.1.1.6.1.1
The VPI identifier of the ATM circuit used for signalling for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmIfSvcSignallingVci 1.3.6.1.4.1.4874.2.2.8.1.1.6.1.2
The VCI identifier of the ATM circuit used for signalling for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmIfSvcSignallingVcd 1.3.6.1.4.1.4874.2.2.8.1.1.6.1.3
The VCI identifier of the ATM circuit used for signalling for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmIfSvcSignallingAdminStatus 1.3.6.1.4.1.4874.2.2.8.1.1.6.1.4
The administrative status of signalling in the ATM interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmVorXAdminStatus  

usdAtmAal5NextIfIndex 1.3.6.1.4.1.4874.2.2.8.1.2.1
Coordinate ifIndex value allocation for entries in usdAtmAal5IfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdAtmAal5IfTable 1.3.6.1.4.1.4874.2.2.8.1.2.2
This table contains entries for ATM AAL5 interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmAal5IfEntry

usdAtmAal5IfEntry 1.3.6.1.4.1.4874.2.2.8.1.2.2.1
Each entry describes the characteristics of an ATM AAL5 interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmAal5IfEntry  

usdAtmAal5IfIndex 1.3.6.1.4.1.4874.2.2.8.1.2.2.1.1
The ifIndex of the ATM AAL5 interface. When creating entries in this table, suitable values for this object are determined by reading usdAtmAal5NextIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmAal5IfRowStatus 1.3.6.1.4.1.4874.2.2.8.1.2.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdAtmAal5IfRowStatus usdAtmAal5IfLowerIfIndex In addition, when creating an entry the following condition must hold: A value for usdAtmAal5IfIndex must have been determined previously, by reading usdAtmAal5NextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created or destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmAal5IfLowerIfIndex 1.3.6.1.4.1.4874.2.2.8.1.2.2.1.3
The ifIndex of an ATM interface over which this ATM AAL5 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdAtmSubIfNextIfIndex 1.3.6.1.4.1.4874.2.2.8.1.3.1
Coordinate ifIndex value allocation for entries in usdAtmSubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdAtmSubIfTable 1.3.6.1.4.1.4874.2.2.8.1.3.2
This table contains entries for ATM Subinterfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmSubIfEntry

usdAtmSubIfEntry 1.3.6.1.4.1.4874.2.2.8.1.3.2.1
Each entry describes the characteristics of an ATM Subinterface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmSubIfEntry  

usdAtmSubIfIndex 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.1
The ifIndex of the ATM Subinterface. When creating entries in this table, suitable values for this object are determined by reading usdAtmSubNextIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmSubIfRowStatus 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdAtmSubIfRowStatus usdAtmSubIfLowerIndex In addition, when creating an entry the following condition must hold: A value for usdAtmSubIfIndex must have been determined previously, by reading usdAtmSubIfNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created or destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmSubIfDistinguisher 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.3
An integer identifier for the subinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfaces configured on the same underlying ATM adaptation layer. The upper bound for the value is further constrained to be identical with the maximum number of subinterfaces supported by the lower interface. If this object is not configured, a value will be allocated internally and can be queried after table entry creation has succeeded.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmSubIfLowerIfIndex 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.4
The ifIndex of an ATM AAL5 interface over which this ATM subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdAtmSubIfNbma 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.5
The NBMA administrative setting. Setting this value of this object to true(1) will enable multipoint access on this interface. Setting the value to false(2), will enable point to point access on this interface.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfAddress 1.3.6.1.4.1.4874.2.2.8.1.3.2.1.6
Specifies the local ATM NSAP address of the circuit. A GET operation returns a full 20-octet NSAP. A SET operation only requires 7 octets, since the prefix can be implied.
Status: current Access: read-create
OBJECT-TYPE    
  AtmAddr Size(0|7|20)  

usdAtmSubIfVccTable 1.3.6.1.4.1.4874.2.2.8.1.3.3
This table contains entries for ATM VCCs configured on ATM subinterfaces present in the system. An implementation may constrain the number of VCCs permitted to be configured per ATM Subinterface; in particular, an implementation may restrict each ATM Subinterface to have a single VCC. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmSubIfVccEntry

usdAtmSubIfVccEntry 1.3.6.1.4.1.4874.2.2.8.1.3.3.1
Each entry describes the characteristics of an ATM subinterface VCC.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmSubIfVccEntry  

usdAtmSubIfVccVpi 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.1
The VPI of the ATM VCC used by this subinterface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmSubIfVccVci 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.2
The VCI of the ATM VCC used by this subinterface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmSubIfVccRowStatus 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdAtmSubIfVccRowStatus In addition, when creating an entry the following conditions must hold: The ATM Subinterface identified by usdAtmSubIfIndex must exist. A positive value configured for usdAtmSubIfVccVcd must not already be assigned to an existing VCC. For each value of usdAtmSubIfVccServiceCategory, additional dependent objects in the entry require configuration as identified here: usdAtmSubIfVccServiceCategory Requires configuration of: ------------------------------------------------------------ ubr ubrPcr usdAtmSubIfVccPcr nrtVbr usdAtmSubIfVccPcr usdAtmSubIfVccScr usdAtmSubIfVccMbs cbr usdAtmSubIfVccPcr rtVbr usdAtmSubIfVccPcr usdAtmSubIfVccScr usdAtmSubIfVccMbs ------------------------------------------------------------ Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmSubIfVccVcd 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.4
An integer identifier for the circuit, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among VCCs configured on the same underlying ATM interface. If this object is not configured, or is configured with a value of zero, a value will be allocated internally and can be queried after table entry creation has succeeded.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmSubIfVccType 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.5
Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM. 'autoconfig' will recognize both VcMux and LLC formats.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rfc1483VcMux(0), rfc1483Llc(1), autoconfig(2)  

usdAtmSubIfVccServiceCategory 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.6
Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-RealTime Variable Bit Rate. cbr Constant Bit Rate. rtVbr Realtime Variable Bit Rate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ubr(0), ubrPcr(1), nrtVbr(2), cbr(3), rtVbr(4)  

usdAtmSubIfVccPcr 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.7
Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when usdAtmSubIfVccServiceCategory is configured to have one of the following values: ubrPcr nrtVbr cbr rtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmSubIfVccScr 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.8
Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when usdAtmSubIfVccServiceCategory is configured to have the following value: nrtVbr rtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmSubIfVccMbs 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.9
Maximum Burst Size, in cells, of this circuit. This parameter is only required when usdAtmSubIfVccServiceCategory is configured to have the following value: nrtVbr rtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmSubIfInverseArp 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.10
Enables the inverse ARP protocol on this VCC; true(1) enables the protocol, false(2) disables it.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfInverseArpRefresh 1.3.6.1.4.1.4874.2.2.8.1.3.3.1.11
The refresh rate in minutes between inverse ARP protocol messages.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmCircuitOamTable 1.3.6.1.4.1.4874.2.2.8.1.3.4
This table contains circuit OAM data for a PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmCircuitOamEntry

usdAtmCircuitOamEntry 1.3.6.1.4.1.4874.2.2.8.1.3.4.1
Each entry provides OAM data on an ATM PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmCircuitOamEntry  

usdAtmCircuitOamIfIndex 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.1
The ifIndex of the ATM subinterface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdAtmCircuitOamVpi 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.2
The VPI of the ATM VCC used by this ATM interface and PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmCircuitOamVci 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.3
The VCI of the ATM VCC used by this ATM interface and PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmCircuitOamAdminStatus 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.4
The administrative state of OAM for the interface identified by this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER oamAdminStateDisabled(1), oamAdminStateEnabled(2)  

usdAtmCircuitOamLoopbackOperStatus 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.5
The operational status of OAM for the interface identified by this entry. oamOperStatusNotSupported(0) - OAM not supported on this interface oamOperStatusDisabled(1) - VC integrity disabled oamOperStatusSent(2) - Loopback sent, awaiting response oamOperStatusReceived(3) - Loopback response received, awaiting frequency oamOperStatusFailed(4) - Loopback response not received, or invalid response received
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oamOperStatusNotSupported(0), oamOperStatusDisabled(1), oamOperStatusSent(2), oamOperStatusReceived(3), oamOperStatusFailed(4)  

usdAtmCircuitVcOamOperStatus 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.6
The OAM VC operational status of this entry. oamVcOperStateAisState(0) - AIS cell received or underlying physical layer reporting transmission path AIS oamVcOperStateRdiState(1) - RDI cell received oamVcOperStateDownRetry(2) - OAM loopback failed, using retry frequency to verify that the VC is really down oamVcOperStateUpRetry(3) - OAM loopback successful, using retry frequency to verify that the VC is really up oamVcOperStateUp(4) - OAM loopback successful after up retry verification oamVcOperStateDown(5) - OAM loopback failed after down retry verification oamVcOperStateNotManaged(6)- No verification via loopback cells being performed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oamVcOperStateAisState(0), oamVcOperStateRdiState(1), oamVcOperStateDownRetry(2), oamVcOperStateUpRetry(3), oamVcOperStateUp(4), oamVcOperStateDown(5), oamVcOperStateNotManaged(6)  

usdAtmCircuitOamLoopbackFrequency 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.7
The OAM loopback frequency for the interface identified by this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..600  

usdAtmCircuitInOamF5Cells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.8
Received OAM F5 cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitInOamCellsDropped 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.9
Received OAM cells that were dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitOutOamF5Cells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.10
Transmitted OAM F5 cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitInOamF5EndToEndLoopbackCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.11
Received OAM F5 end-to-end loopback cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitInOamF5SegmentLoopbackCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.12
Received OAM F5 segment loopback cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitInOamF5AisCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.13
Received OAM F5 AIS cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitInOamF5RdiCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.14
Received OAM F5 RDI cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitOutOamF5EndToEndLoopbackCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.15
Transmitted OAM F5 end-to-end loopback cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitOutOamF5SegmentLoopbackCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.16
Transmitted OAM F5 segment loopback cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmCircuitOutOamF5RdiCells 1.3.6.1.4.1.4874.2.2.8.1.3.4.1.17
Transmitted OAM F5 RDI cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

usdAtmSubIfVccTrafficShapingTable 1.3.6.1.4.1.4874.2.2.8.1.3.5
This table contains entries for traffic shaping of ATM VCCs configured on ATM subinterfaces present in the system. This table augments the usdAtmSubIfVccTable only for VCCs that support traffic shapping. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmSubIfVccTrafficShapingEntry

usdAtmSubIfVccTrafficShapingEntry 1.3.6.1.4.1.4874.2.2.8.1.3.5.1
Each entry describes the traffic shping characteristics of an ATM subinterface VCC.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmSubIfVccTrafficShapingEntry  

usdAtmSubIfVccTrafficShapingCdvt 1.3.6.1.4.1.4874.2.2.8.1.3.5.1.1
The network cell delay variation tolerance (CDVT) in tenths of a microsecond.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

usdAtmSubIfVccTrafficShapingClp0 1.3.6.1.4.1.4874.2.2.8.1.3.5.1.2
Specifies whether or not only CLP0 cells are to be policed according to the traffic contract. CLP1 cells are forwarded on a best-effort basis CLP-significant model for (VBR.2, VBR.3 conformance). Applicable only for VBR circuits.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfVccTrafficShapingTagging 1.3.6.1.4.1.4874.2.2.8.1.3.5.1.3
Specifies whether or not CLP0 cells should be tagged for SCR policing (VBR.3 conformance). Applicable only for VBR circuits.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfVccTrafficShapingPoliceObserve 1.3.6.1.4.1.4874.2.2.8.1.3.5.1.4
Specifies whether of not no policing action is to be taken (note the double negative; if true(1) then no policing action will be taken; if false(2) then policing action will be taken). Regardless of the state of this object, all counters will be incremented.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfVccTrafficShapingPacketShaping 1.3.6.1.4.1.4874.2.2.8.1.3.5.1.5
Specifies whether of not to shape output traffic on a packet boundary.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfSvcConfigTable 1.3.6.1.4.1.4874.2.2.8.1.3.6
This table contains entries for extending the usdAtmSubIfTable to configure switched virtual connection (SVC)on the subinterfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmSubIfSvcConfigEntry

usdAtmSubIfSvcConfigEntry 1.3.6.1.4.1.4874.2.2.8.1.3.6.1
Each entry provides configuration parameters for an ATM SVC on the subinterface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmSubIfSvcConfigEntry  

usdAtmSubIfSvcRowStatus 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.1
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmSubIfSvcConfigDestAtmAddress 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.2
Specifies the destination ATM NSAP address of the circuit.
Status: current Access: read-create
OBJECT-TYPE    
  AtmAddr Size(20)  

usdAtmSubIfSvcConfigCircuitType 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.3
Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rfc1483VcMux(0), rfc1483Llc(1)  

usdAtmSubIfSvcConfigServiceCategory 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.4
Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-RealTime Variable Bit Rate. cbr Constant Bit Rate. rtVbr Realtime Variable Bit Rate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ubr(0), ubrPcr(1), nrtVbr(2), cbr(3), rtVbr(4)  

usdAtmSubIfSvcConfigPcr 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.5
Peak Cell Rate, in kilo-bits per second (kbps), of this circuit.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

usdAtmSubIfSvcConfigScr 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.6
Sustained Cell Rate, in kilo-bits per second (kbps), of this circuit.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

usdAtmSubIfSvcConfigMbs 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.7
Maximum Burst Size, in cells, of this circuit.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

usdAtmSubIfSvcConfigCdvt 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.8
Specify the network Cell Delay Variation Tolerance.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

usdAtmSubIfSvcConfigClp0 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.9
Specify that only CLP0 cells are to be policed according to the traffic contract. CLP1 cells are forwarded on a best-effort basis CLP-significant model for (VBR.2, VBR.3 conformance).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfSvcConfigTagging 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.10
Specify that CLP0 cells should be tagged for SCR policing (VBR.3 conformance).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfSvcConfigObserve 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.11
Specify that no policing action is to be taken; only counters are incremented.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmSubIfSvcConfigPacketDiscard 1.3.6.1.4.1.4874.2.2.8.1.3.6.1.12
Enable early packet Discard for this circuit.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmNbmaMapTable 1.3.6.1.4.1.4874.2.2.8.1.4.1
This table contains entries for ATM NBMA maps.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmNbmaMapEntry

usdAtmNbmaMapEntry 1.3.6.1.4.1.4874.2.2.8.1.4.1.1
Each entry describes the characteristics of an ATM NBMA map.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmNbmaMapEntry  

usdAtmNbmaMapName 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.1
The NBMA map name.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmNbmaMapName  

usdAtmNbmaMapVcd 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.2
An integer identifier for the ATM circuit, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

usdAtmNbmaMapIpAddress 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.3
The IP address associated with this entry.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdAtmNbmaMapVpi 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.4
The VPI identifier of the ATM circuit.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

usdAtmNbmaMapVci 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.5
The VCI identifier of the ATM circuit.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

usdAtmNbmaMapIfIndex 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.6
The ifIndex of the ATM major interface associated with this entry. The value of this object will be zero when the map is not applied to an interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdAtmNbmaMapBroadcast 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.7
The broadcast enable/disable setting for this entry. The value true(1) enable broadcast support; disable(2) disabled broadcast support for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdAtmNbmaMapRowStatus 1.3.6.1.4.1.4874.2.2.8.1.4.1.1.8
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy Additional notes to aid the network manager: - NBMA maps are not supported on dynamic interface. - NBMA maps can only be applied to a single major ATM interface at a time. - NBMA maps cannot be deleted unless the map is removed from the ATM interface (usdAtmNbmaMapIfIndex = 0). - The values of usdAtmNbmaMapVpi, usdAtmNbmaMapVci and usdAtmNbmaMapIfIndex are zero until the map is applied to a major ATM interface. - To create an entry in this table, the following objects must be present in the set PDU: usdAtmNbmaMapIpAddress usdAtmNbmaMapBroadcast usdAtmNbmaMapRowStatus - Once created, only the following objects can be modified: usdAtmNbmaMapBroadcast
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmNbmaMapListTable 1.3.6.1.4.1.4874.2.2.8.1.4.2
This table contains entries for ATM NBMA map lists.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmNbmaMapListEntry

usdAtmNbmaMapListEntry 1.3.6.1.4.1.4874.2.2.8.1.4.2.1
Each entry describes the characteristics of an ATM NBMA map.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmNbmaMapListEntry  

usdAtmNbmaMapListName 1.3.6.1.4.1.4874.2.2.8.1.4.2.1.1
The NBMA Map List name.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmNbmaMapName  

usdAtmNbmaMapListRowStatus 1.3.6.1.4.1.4874.2.2.8.1.4.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdAtmPingTestTypes 1.3.6.1.4.1.4874.2.2.8.1.5.1
OBJECT IDENTIFIER    

usdAtmPingTestOamSeg 1.3.6.1.4.1.4874.2.2.8.1.5.1.1
This identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC, VCL, or VCC termination point, using segment OAM cells. The test type must have appended to it a code that uniquely identifies an intermediate point responsible for looping back each cell. If this is absent, the loopbacks are performed at the end of the segment or connection. E.g., the OID { usdAtmPingTestOamSeg 5 } identifies that the loopbacks should be performed at the intermediate point labeled 5.
Status: current Access: read-create
OBJECT-IDENTITY    

usdAtmPingTestOamE2E 1.3.6.1.4.1.4874.2.2.8.1.5.1.2
This identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC, VCL, or VCC termination point, using end-to-end OAM cells.
Status: current Access: read-create
OBJECT-IDENTITY    

usdAtmVpPingTable 1.3.6.1.4.1.4874.2.2.8.1.5.2
This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB atmM4VpTestTable to do ping (multiple loopback) type testing.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmVpPingEntry

usdAtmVpPingEntry 1.3.6.1.4.1.4874.2.2.8.1.5.2.1
Each entry describes the characteristics, status and results of the most recent ATM ping test.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmVpPingEntry  

usdAtmVpPingProbeCount 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.1
The number of ping probes (OAM cells) to be sent to complete the test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..30  

usdAtmVpPingTimeOut 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.2
Specifies the time-out value, in seconds, for a remote ping operation.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..5  

usdAtmVpPingCtlTrapGeneration 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.3
The value of this object determines when and if to generate a notification for this entry: testCompletion(0) - Generate a usdPingTestCompleted notification. The value of this object defaults to zero, indicating that no notification has been selected.
Status: current Access: read-write
OBJECT-TYPE    
  BITS testCompletion(0)  

usdAtmVpPingSentProbes 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.4
The number of ping probes (OAM cells) that have been sent thus far for this test. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVpPingProbeResponses 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.5
The number of ping responses that have been received thus far for this test. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVpPingStartTime 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.6
The time (sysUpTime) when the test started.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

usdAtmVpPingMinRtt 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.7
The shortest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVpPingMaxRtt 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.8
The longest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVpPingAverageRtt 1.3.6.1.4.1.4874.2.2.8.1.5.2.1.9
The average round-trip-time (RTT) for all the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVcPingTable 1.3.6.1.4.1.4874.2.2.8.1.5.3
This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB atmM4VcTestTable to do ping (multiple loopback) type testing.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdAtmVcPingEntry

usdAtmVcPingEntry 1.3.6.1.4.1.4874.2.2.8.1.5.3.1
Each entry describes the characteristics, status and results of the most recent ATM ping test.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdAtmVcPingEntry  

usdAtmVcPingProbeCount 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.1
The number of ping probes (OAM cells) to be sent to complete the test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..30  

usdAtmVcPingTimeOut 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.2
Specifies the time-out value, in seconds, for a remote ping operation.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..5  

usdAtmVcPingCtlTrapGeneration 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.3
The value of this object determines when and if to generate a notification for this entry: testCompletion(0) - Generate a usdPingTestCompleted notification. The value of this object defaults to zero, indicating that no notification has been selected.
Status: current Access: read-write
OBJECT-TYPE    
  BITS testCompletion(0)  

usdAtmVcPingSentProbes 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.4
The number of ping probes (OAM cells) that have been sent thus far for this test. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVcPingProbeResponses 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.5
The number of ping responses that have been received thus far for this test. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVcPingStartTime 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.6
The time (sysUpTime) when the test started.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

usdAtmVcPingMinRtt 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.7
The shortest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVcPingMaxRtt 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.8
The longest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmVcPingAverageRtt 1.3.6.1.4.1.4874.2.2.8.1.5.3.1.9
The average round-trip-time (RTT) for all the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

usdAtmTraps 1.3.6.1.4.1.4874.2.2.8.3
OBJECT IDENTIFIER    

usdAtmTrapPrefix 1.3.6.1.4.1.4874.2.2.8.3.0
OBJECT IDENTIFIER    

usdAtmVpPingTestCompleted 1.3.6.1.4.1.4874.2.2.8.3.0.1
Generated at the completion of a AtmfM4VpTest when the corresponding usdAtmVpPingCtlTrapGeneration object has the testCompletion(0) bit set.
Status: current Access: read-only
NOTIFICATION-TYPE    

usdAtmVcPingTestCompleted 1.3.6.1.4.1.4874.2.2.8.3.0.2
Generated at the completion of a AtmfM4VcTest when the corresponding usdAtmVcPingCtlTrapGeneration object has the testCompletion(0) bit set.
Status: current Access: read-only
NOTIFICATION-TYPE    

usdAtmConformance 1.3.6.1.4.1.4874.2.2.8.4
OBJECT IDENTIFIER    

usdAtmCompliances 1.3.6.1.4.1.4874.2.2.8.4.1
OBJECT IDENTIFIER    

usdAtmGroups 1.3.6.1.4.1.4874.2.2.8.4.2
OBJECT IDENTIFIER    

usdAtmCompliance 1.3.6.1.4.1.4874.2.2.8.4.1.1
Obsolete compliance statement for entities which implement the Unisphere ATM MIB. This statement became obsolete when support was added for NBMA map lists and ATM ping.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAtmCompliance2 1.3.6.1.4.1.4874.2.2.8.4.1.2
Obsolete compliance statement for entities which implement the Unisphere ATM MIB. This statement became obsolete when support was added for traffic shapping on VCC subinterfaces.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAtmCompliance3 1.3.6.1.4.1.4874.2.2.8.4.1.3
Obsolete compliance statement for entities which implement the Unisphere ATM MIB. This statement became obsolete when support was added for connection admission control (CAC).
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAtmCompliance4 1.3.6.1.4.1.4874.2.2.8.4.1.4
Obsolete compliance statement for entities which implement the Unisphere ATM MIB. This statement became obsolete when ATM SVC, CAC used bandwidth and sub-interface address objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdAtmCompliance5 1.3.6.1.4.1.4874.2.2.8.4.1.5
The compliance statement for entities which implement the Unisphere ATM MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

usdAtmGroup 1.3.6.1.4.1.4874.2.2.8.4.2.1
Obsolete collection of objects providing management of ATM interfaces in a Unisphere product. This group became obsolete when the usdAtmIfMapGroup object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAtmAal5Group 1.3.6.1.4.1.4874.2.2.8.4.2.2
A collection of objects providing management of AAL5 interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmSubIfGroup 1.3.6.1.4.1.4874.2.2.8.4.2.3
Obsolete collection of objects providing management of ATM subinterfaces in a Unisphere product. This group became obsolete when usdAtmSubIfNbma, usdAtmSubIfInverseArp, and usdAtmSubIfInverseArpRefresh were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAtmVpTunnelGroup 1.3.6.1.4.1.4874.2.2.8.4.2.4
A collection of objects providing management of VP tunnels in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmNbmaMapGroup 1.3.6.1.4.1.4874.2.2.8.4.2.5
A collection of object providing management of NBMA in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmSubIfGroup2 1.3.6.1.4.1.4874.2.2.8.4.2.6
Obsolete collection of objects providing management of ATM subinterfaces in a Unisphere product. This group became obsolete when usdAtmSubIfAddress was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAtmVpPingControlGroup 1.3.6.1.4.1.4874.2.2.8.4.2.7
A collection of object providing management of ATM VPL Ping testing in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmVcPingControlGroup 1.3.6.1.4.1.4874.2.2.8.4.2.8
A collection of object providing management of ATM VCL Ping testing in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmPingTrapGroup 1.3.6.1.4.1.4874.2.2.8.4.2.9
A collection of notifications supporting ATM Ping testing in a Unisphere product.
Status: current Access: read-only
NOTIFICATION-GROUP    

usdAtmGroup2 1.3.6.1.4.1.4874.2.2.8.4.2.10
Obsolete collection of objects providing management of ATM interfaces in a Unisphere product. This group became obsolete when support was added for connection admission control (CAC).
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAtmTrafficShapingGroup 1.3.6.1.4.1.4874.2.2.8.4.2.11
A collection of objects providing management of ATM traffic shaping in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmGroup3 1.3.6.1.4.1.4874.2.2.8.4.2.12
Obsolete collection of objects providing management of ATM interfaces in a Unisphere product. This group became obsolete when support was added for connection admission control (CAC) used bandwidth.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdAtmGroup4 1.3.6.1.4.1.4874.2.2.8.4.2.13
A collection of objects providing management of ATM interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmSvcGroup 1.3.6.1.4.1.4874.2.2.8.4.2.14
A collection of objects providing management of ATM SVC interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdAtmSubIfGroup3 1.3.6.1.4.1.4874.2.2.8.4.2.15
A collection of objects providing management of ATM subinterfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP