Unisphere-Data-IF-MIB

File: Unisphere-Data-IF-MIB.mib (12804 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB Unisphere-Data-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE TEXTUAL-CONVENTION
RowStatus MODULE-COMPLIANCE OBJECT-GROUP
ifEntry ifStackHigherLayer ifStackLowerLayer
usDataMibs

Defined Types

UsdIfType  
Interface type identification for physical-, link-, and network-layer interfaces.
TEXTUAL-CONVENTION    
  INTEGER ip(0), ppp(1), ds0(2), ds1(3), ds3(4), frameRelay(5), ethernet(6), sonet(7), sonetPath(8), atm(9), aal5(10), atmSubInterface(11), ft1(12), hdlc(13), ipLoopback(14), ipVirtual(15), frSubInterface(16), pppoe(17), pppoeSubInterface(18), bridgedEthernet(19), l2tpTunnelInterface(20), l2tpSessionInterface(21), mlPppLinkInterface(22), slepInterface(23), l2tpDestinationInterface(24), mplsMajorInterface(25), mplsMinorInterface(26), mlPppNetworkInterface(27), ethernetSubInterface(28), multilinkFrameRelayInterface(29), ipTunnelInterface(30), serverPortInterface(31), smdsInterface(32), sonetVTInterface(33), vlanMajorInterface(34), vlanSubInterface(35), cbfInterface(36), gtpInterface(37), smdsMajorInterface(38), smdsSubInterface(39), l2fTunnelInterface(40), l2fSessionInterface(41), l2fDestinationInterface(42), ipsecInterface(43), sgInterface(44), lacGenInterface(47)  

UsdIfEntry  
SEQUENCE    
  usdIfType UsdIfType

UsdIfInvStackEntry  
SEQUENCE    
  usdIfInvStackStatus RowStatus

Defined Values

usdIfMIB 1.3.6.1.4.1.4874.2.2.3
The Generic Interfaces MIB for the Unisphere Networks Inc. enterprise.
MODULE-IDENTITY    

usdInterfaces 1.3.6.1.4.1.4874.2.2.3.1
OBJECT IDENTIFIER    

usdIf 1.3.6.1.4.1.4874.2.2.3.1.1
OBJECT IDENTIFIER    

usdIfObjects 1.3.6.1.4.1.4874.2.2.3.1.1.1
OBJECT IDENTIFIER    

usdIfTable 1.3.6.1.4.1.4874.2.2.3.1.1.1.1
This table contains a corresponding entry for each entry found in the standard Generic Interfaces MIB ifTable/ifXTable. The entries in this table contain supplementary generic interface characteristics. Entries in ifTable/ifXTable and in this table are created/deleted as a consequence of hardware detection, or of management configuration via standard or enterprise type-specific interface MIBs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdIfEntry

usdIfEntry 1.3.6.1.4.1.4874.2.2.3.1.1.1.1.1
An entry representing an interface's enterprise-defined generic interface characteristics.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdIfEntry  

usdIfType 1.3.6.1.4.1.4874.2.2.3.1.1.1.1.1.1
Identifies the type of this interface.
Status: current Access: read-only
OBJECT-TYPE    
  UsdIfType  

usdIfInvStackTable 1.3.6.1.4.1.4874.2.2.3.1.1.1.2
A table containing information on the relationships between the multiple sub-layers of network interfaces. In particular, it contains information on which sub-layers run 'underneath' which other sub-layers, where each sub-layer corresponds to a conceptual row in the ifTable. For example, when the sub-layer with ifIndex value x runs underneath the sub-layer with ifIndex value y, then this table contains: usdIfInvStackStatus.x.y=active For each ifIndex value, I, which identifies an active interface, there are always at least two instantiated rows in this table associated with I. For one of these rows, I is the value of ifStackHigherLayer; for the other, I is the value of ifStackLowerLayer. (If I is not involved in multiplexing, then these are the only two rows associated with I.) For example, two rows exist even for an interface which has no others stacked on top or below it: ifStackStatus.x.0=active ifStackStatus.0.x=active This table contains exactly the same number of rows as the ifStackTable, but the rows appear in a different order.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdIfInvStackEntry

usdIfInvStackEntry 1.3.6.1.4.1.4874.2.2.3.1.1.1.2.1
Information on a particular relationship between two sub-layers, specifying that one sub-layer runs underneath the other sub-layer. Each sub-layer corresponds to a conceptual row in the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdIfInvStackEntry  

usdIfInvStackStatus 1.3.6.1.4.1.4874.2.2.3.1.1.1.2.1.1
The status of the relationship between two sub-layers. An instance of this object exists for each instance of the ifStackStatus object, and vice versa. For example, if the variable ifStackStatus.H.L exists, then the variable usdIfInvStackStatus.L.H must also exist, and vice versa. In addition, the two variables always have the same value. However, unlike ifStackStatus, the usdIfInvStackStatus object is NOT write-able. A network management application wishing to change a relationship between sub-layers H and L cannot do so by modifying the value of usdIfInvStackStatus.L.H, but must instead modify the value of ifStackStatus.H.L. After the ifStackTable is modified, the change will be reflected in this table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

usdIfConformance 1.3.6.1.4.1.4874.2.2.3.1.1.4
OBJECT IDENTIFIER    

usdIfCompliances 1.3.6.1.4.1.4874.2.2.3.1.1.4.1
OBJECT IDENTIFIER    

usdIfGroups 1.3.6.1.4.1.4874.2.2.3.1.1.4.2
OBJECT IDENTIFIER    

usdIfCompliance 1.3.6.1.4.1.4874.2.2.3.1.1.4.1.1
The compliance statement for entities which implement the Unisphere Generic Interfaces MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

usdIfGroup 1.3.6.1.4.1.4874.2.2.3.1.1.4.2.1
A collection of objects for managing generic interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdIfInvStackGroup 1.3.6.1.4.1.4874.2.2.3.1.1.4.2.2
A collection of objects providing inverted information on the layering of MIB-II interfaces.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor