Unisphere-Data-MPLS-MIB

File: Unisphere-Data-MPLS-MIB.mib (99531 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB Unisphere-Data-MIBs Unisphere-Data-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
IpAddress Unsigned32 RowStatus
DisplayString TruthValue TEXTUAL-CONVENTION
MODULE-COMPLIANCE OBJECT-GROUP InterfaceIndex
InterfaceIndexOrZero usDataMibs UsdNextIfIndex

Defined Types

UsdMajorCfgVciRanges  
Generic VCI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP).
TEXTUAL-CONVENTION    
  Integer32 33..65535  

UsdMajorCfgVpiRanges  
Generic VPI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP).
TEXTUAL-CONVENTION    
  Integer32 0..255  

UsdMinorCfgBWRanges  
Specifies bandwidth requirements for each MPLS tunnel.
TEXTUAL-CONVENTION    
  Unsigned32  

UsdMinorCfgHoldingAndSetupPriorityRanges  
Each LSP has a setup and hold priority before setting it up or preempting it relative to the other LSPs. This convention specifies those ranges.
TEXTUAL-CONVENTION    
  Integer32 0..7  

UsdMinorCfgRetryTimesAndNorouteRanges  
RSVP/LDP will have a number of retries for successfully setting up a tunnel. This value specifies retry value ranges for LDP/RSVP with or without no-route notification.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

UsdMinorCfgRetryIntervalAndNorouteRanges  
RSVP/LDP will have time interval between two successive retries for setting up tunnel successfully. This value specifies the interval ranges for LDP/RSVP with or without no-route notification.
TEXTUAL-CONVENTION    
  Integer32 0..60  

UsdProfileCfgBWRanges  
Bandwidth range specified for each tunnel in tunnel profiling.
TEXTUAL-CONVENTION    
  Unsigned32  

UsdProfileCfgHoldingAndSetupPriorityRanges  
Tunnel setup and hold priority range specified for each tunnel in tunnel profile configuration.
TEXTUAL-CONVENTION    
  Integer32 0..7  

UsdProfileCfgRetryTimesAndNorouteRanges  
Range specified for number of retries for tunnel with or without no-route notification for RSVP/LDP.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

UsdProfileCfgRetryIntervalAndNorouteRanges  
Range specified for retry interval for tunnel with or without no-route notification for RSVP/LDP.
TEXTUAL-CONVENTION    
  Integer32 0..60  

UsdMplsGroupTargetedHelloSendEntry  
SEQUENCE    
  usdMplsGroupTargetedHelloSendAddress IpAddress
  usdMplsGroupLdpTargetedHelloSendMode INTEGER

UsdMplsGroupTargetedHelloReceiveEntry  
SEQUENCE    
  usdMplsGroupTargetedHelloReceiveAddress IpAddress
  usdMplsGroupLdpTargetedHelloReceiveMode INTEGER

UsdMplsGroupLdpLabelAdverRouteListEntry  
SEQUENCE    
  usdMplsGroupLdpLabelAdverRouteListName DisplayString
  usdMplsGroupLdpLabelAdverNbrListName DisplayString
  usdMplsGroupLabelAdverListMode INTEGER

UsdMplsGroupLdpProfileEntry  
SEQUENCE    
  usdMplsGroupLdpProfileName DisplayString
  usdMplsGroupLdpProfileHelloHoldTime Integer32
  usdMplsGroupLdpProfileCrLdpAdminState INTEGER
  usdMplsGroupLdpProfileRowStatus RowStatus

UsdMplsGroupRsvpProfileEntry  
SEQUENCE    
  usdMplsGroupRsvpProfileName DisplayString
  usdMplsGroupRsvpProfileRefreshPeriod Unsigned32
  usdMplsGroupRsvpProfileCleanupTimeoutFactor Integer32
  usdMplsGroupRsvpProfileRowStatus RowStatus

UsdMplsIfMajorEntry  
SEQUENCE    
  usdMplsIfMajorIndex InterfaceIndex
  usdMplsIfMajorRowStatus RowStatus
  usdMplsIfMajorLowerIfIndex InterfaceIndexOrZero
  usdMplsIfMajorAdminStatus INTEGER
  usdMplsIfMajorLdpAdminStatus INTEGER
  usdMplsIfMajorLdpProfileName DisplayString
  usdMplsIfMajorLdpVpiStart UsdMajorCfgVpiRanges
  usdMplsIfMajorLdpVpiStop UsdMajorCfgVpiRanges
  usdMplsIfMajorLdpVciStart UsdMajorCfgVciRanges
  usdMplsIfMajorLdpVciStop UsdMajorCfgVciRanges
  usdMplsIfMajorRsvpAdminStatus INTEGER
  usdMplsIfMajorRsvpProfileName DisplayString
  usdMplsIfMajorRsvpVpiStart UsdMajorCfgVpiRanges
  usdMplsIfMajorRsvpVpiStop UsdMajorCfgVpiRanges
  usdMplsIfMajorRsvpVciStart UsdMajorCfgVciRanges
  usdMplsIfMajorRsvpVciStop UsdMajorCfgVciRanges
  usdMplsIfMajorLabelSpaceType INTEGER
  usdMplsIfMajorOpState INTEGER
  usdMplsIfMajorCrLdpAdminState INTEGER

UsdMplsIfMinorEntry  
SEQUENCE    
  usdMplsIfMinorIndex InterfaceIndex
  usdMplsIfMinorRowStatus RowStatus
  usdMplsIfMinorLowerIfIndex InterfaceIndexOrZero
  usdMplsIfMinorAdminStatus INTEGER
  usdMplsIfMinorEndpointAddress IpAddress
  usdMplsIfMinorEndpointDstMask IpAddress
  usdMplsIfMinorTunnelMetricMode INTEGER
  usdMplsIfMinorAbsoluteTunnelMetric Unsigned32
  usdMplsIfMinorRelativeTunnelMetric Integer32
  usdMplsIfMinorLabelDistProto INTEGER
  usdMplsIfMinorAnnounceToOspf TruthValue
  usdMplsIfMinorAnnounceToIsis TruthValue
  usdMplsIfMinorAnnounceToBgp TruthValue
  usdMplsIfMinorBandwidth UsdMinorCfgBWRanges
  usdMplsIfMinorAffinity OCTET STRING
  usdMplsIfMinorAffinityMask OCTET STRING
  usdMplsIfMinorSetupPriority UsdMinorCfgHoldingAndSetupPriorityRanges
  usdMplsIfMinorHoldingPriority UsdMinorCfgHoldingAndSetupPriorityRanges
  usdMplsIfMinorTunnelName DisplayString
  usdMplsIfMinorTunnelRetryTimes UsdMinorCfgRetryTimesAndNorouteRanges
  usdMplsIfMinorTunnelRetryInterval UsdMinorCfgRetryIntervalAndNorouteRanges
  usdMplsIfMinorTunnelRetryTimesNoroute UsdMinorCfgRetryTimesAndNorouteRanges
  usdMplsIfMinorTunnelRetryIntervalNoroute UsdMinorCfgRetryIntervalAndNorouteRanges
  usdMplsIfMinorBaseTunnelName DisplayString
  usdMplsIfMinorVpnOuiNumber Integer32
  usdMplsIfMinorVpnIndex IpAddress
  usdMplsIfMinorTunnelOpState INTEGER
  usdMplsIfMinorTargetedDynamicTunnel TruthValue
  usdMplsIfMinorReoptimization TruthValue

UsdMplsIfMinorPathOptionEntry  
SEQUENCE    
  usdMplsIfMinorPathOptionIndex InterfaceIndex
  usdMplsIfMinorPathOptionNumber Integer32
  usdMplsIfMinorPathOptionProtocol INTEGER
  usdMplsIfMinorPathOptionLockdown TruthValue
  usdMplsIfMinorPathOptionPathName DisplayString
  usdMplsIfMinorPathOptionPathId Integer32
  usdMplsIfMinorPathOptionRowStatus RowStatus

UsdMplsTunnelProfileEntry  
SEQUENCE    
  usdMplsTunnelProfileName DisplayString
  usdMplsTunnelProfileAdminStatus INTEGER
  usdMplsTunnelProfileBaseTunnelName DisplayString
  usdMplsTunnelProfileIpProfileName DisplayString
  usdMplsTunnelProfileLabelDistProto INTEGER
  usdMplsTunnelProfileAnnounceToOspf TruthValue
  usdMplsTunnelProfileAnnounceToIsis TruthValue
  usdMplsTunnelProfileAnnounceToBgp TruthValue
  usdMplsTunnelProfileMetricMode INTEGER
  usdMplsTunnelProfileAbsoluteMetric Unsigned32
  usdMplsTunnelProfileRelativeMetric Integer32
  usdMplsTunnelProfileBandwidth UsdProfileCfgBWRanges
  usdMplsTunnelProfileAffinity OCTET STRING
  usdMplsTunnelProfileAffinityMask OCTET STRING
  usdMplsTunnelProfileSetupPriority UsdProfileCfgHoldingAndSetupPriorityRanges
  usdMplsTunnelProfileHoldingPriority UsdProfileCfgHoldingAndSetupPriorityRanges
  usdMplsTunnelProfileRetryTimes UsdProfileCfgRetryTimesAndNorouteRanges
  usdMplsTunnelProfileRetryInterval UsdProfileCfgRetryIntervalAndNorouteRanges
  usdMplsTunnelProfileRetryTimesNoroute UsdProfileCfgRetryTimesAndNorouteRanges
  usdMplsTunnelProfileRetryIntervalNoroute UsdProfileCfgRetryIntervalAndNorouteRanges
  usdMplsTunnelProfileVpnOuiNumber Integer32
  usdMplsTunnelProfileVpnIndex IpAddress
  usdMplsTunnelProfileRowStatus RowStatus
  usdMplsTunnelProfileTargetedDynamicTunnel TruthValue

UsdMplsTunnelProfilePathOptionEntry  
SEQUENCE    
  usdMplsTunnelProfileNamePathOption DisplayString
  usdMplsTunnelProfilePathOptionNumber Integer32
  usdMplsTunnelProfilePathOptionProtocol INTEGER
  usdMplsTunnelProfilePathOptionLockdown TruthValue
  usdMplsTunnelProfilePathOptionPathName DisplayString
  usdMplsTunnelProfilePathOptionPathId Integer32
  usdMplsTunnelProfilePathOptionRowStatus RowStatus

UsdMplsTunnelProfileDynamicEndpointEntry  
SEQUENCE    
  usdMplsTunnelProfileNameDynamicEndpoint DisplayString
  usdMplsTunnelProfileDynamicEndpointType INTEGER
  usdMplsTunnelProfileDynamicEndpointPolicyListType INTEGER
  usdMplsTunnelProfileDynamicEndpointListName DisplayString
  usdMplsTunnelProfileDynamicEndpointRowStatus RowStatus

UsdMplsTunnelProfileTunnelEndpointEntry  
SEQUENCE    
  usdMplsTunnelProfileNameTunnelEndpoint DisplayString
  usdMplsTunnelProfileTunnelEndpointAddress IpAddress
  usdMplsTunnelProfileTunnelEndpointDstMask IpAddress
  usdMplsTunnelProfileTunnelEndpointRowStatus RowStatus

UsdMplsExplicitPathEntry  
SEQUENCE    
  usdMplsExplicitPathName DisplayString
  usdMplsExplicitPathAdminState INTEGER
  usdMplsExplicitPathRowStatus RowStatus

UsdMplsExplicitPathNodeEntry  
SEQUENCE    
  usdMplsExplicitPathNodeName DisplayString
  usdMplsExplicitPathNodeIndexNumber Integer32
  usdMplsExplicitPathNodeLoose TruthValue
  usdMplsExplicitPathNodeHopAddress IpAddress
  usdMplsExplicitPathNodeHopAddressMask IpAddress
  usdMplsExplicitPathNodeRowStatus RowStatus

Defined Values

usdMplsMIB 1.3.6.1.4.1.4874.2.2.54
The MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations.
MODULE-IDENTITY    

usdMplsObjects 1.3.6.1.4.1.4874.2.2.54.1
OBJECT IDENTIFIER    

usdMplsLsrGlobalConfig 1.3.6.1.4.1.4874.2.2.54.1.1
OBJECT IDENTIFIER    

usdMplsMajorLayer 1.3.6.1.4.1.4874.2.2.54.1.2
OBJECT IDENTIFIER    

usdMplsMinorLayer 1.3.6.1.4.1.4874.2.2.54.1.3
OBJECT IDENTIFIER    

usdMplsTunnelProfile 1.3.6.1.4.1.4874.2.2.54.1.4
OBJECT IDENTIFIER    

usdMplsExplicitPath 1.3.6.1.4.1.4874.2.2.54.1.5
OBJECT IDENTIFIER    

usdMplsGroup 1.3.6.1.4.1.4874.2.2.54.1.1.1
OBJECT IDENTIFIER    

usdMplsGroupList 1.3.6.1.4.1.4874.2.2.54.1.1.2
OBJECT IDENTIFIER    

usdMplsIfMajorLayer 1.3.6.1.4.1.4874.2.2.54.1.2.1
OBJECT IDENTIFIER    

usdMplsIfMinorLayer 1.3.6.1.4.1.4874.2.2.54.1.3.1
OBJECT IDENTIFIER    

usdMplsMinorLayerList 1.3.6.1.4.1.4874.2.2.54.1.3.2
OBJECT IDENTIFIER    

usdMplsTunnelProfileGroup 1.3.6.1.4.1.4874.2.2.54.1.4.1
OBJECT IDENTIFIER    

usdMplsTunnelProfileList 1.3.6.1.4.1.4874.2.2.54.1.4.2
OBJECT IDENTIFIER    

usdMplsExplicitPathGroup 1.3.6.1.4.1.4874.2.2.54.1.5.1
OBJECT IDENTIFIER    

usdMplsGroupMplsEnable 1.3.6.1.4.1.4874.2.2.54.1.1.1.1
Enables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsGroupReopTimer 1.3.6.1.4.1.4874.2.2.54.1.1.1.2
All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..604800  

usdMplsGroupLabelRangeLow 1.3.6.1.4.1.4874.2.2.54.1.1.1.3
The lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..1048576  

usdMplsGroupLabelRangeHigh 1.3.6.1.4.1.4874.2.2.54.1.1.1.4
The higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..1048576  

usdMplsGroupLspRetryTimesNoroute 1.3.6.1.4.1.4874.2.2.54.1.1.1.5
This object configures the number of retries for LSP setup after a failure due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

usdMplsGroupLspRetryIntervalNoroute 1.3.6.1.4.1.4874.2.2.54.1.1.1.6
This object configures the time interval between two successive LSP setup retries after a failure due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..60  

usdMplsGroupLspRetryTimes 1.3.6.1.4.1.4874.2.2.54.1.1.1.7
Use this object to configure number of retries for LSP setup after a failure other than one due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

usdMplsGroupLspRetryInterval 1.3.6.1.4.1.4874.2.2.54.1.1.1.8
Use this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..60  

usdMplsGroupLdpRetryTimesNoroute 1.3.6.1.4.1.4874.2.2.54.1.1.1.9
Use this object to configure the number of retries for LDP to setup LSP after a failure due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

usdMplsGroupLdpRetryIntervalNoroute 1.3.6.1.4.1.4874.2.2.54.1.1.1.10
Use this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..60  

usdMplsGroupLdpRetryTimes 1.3.6.1.4.1.4874.2.2.54.1.1.1.11
Use this object to configure LSP setup retries by LDP after a failure other than one due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

usdMplsGroupLdpRetryInterval 1.3.6.1.4.1.4874.2.2.54.1.1.1.12
Use this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..60  

usdMplsGroupLdpSessionRetries 1.3.6.1.4.1.4874.2.2.54.1.1.1.13
Use this object to configure the number of LDP session retries.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..128  

usdMplsGroupLdpSessionRetryTimer 1.3.6.1.4.1.4874.2.2.54.1.1.1.14
Use this object to configure the time interval between two LDP session retries.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..60  

usdMplsGroupTopologyDrivenIpProfileName 1.3.6.1.4.1.4874.2.2.54.1.1.1.15
Usually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

usdMplsGroupTopologyDrivenLdpEgressIpIntf 1.3.6.1.4.1.4874.2.2.54.1.1.1.16
This object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupTopologyDrivenLdpIngressIpIntf 1.3.6.1.4.1.4874.2.2.54.1.1.1.17
This object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupTopologyDrivenLdpEgressIpIntfHostOnly 1.3.6.1.4.1.4874.2.2.54.1.1.1.18
This object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupTopologyDrivenLdpIngressIpIntfHostOnly 1.3.6.1.4.1.4874.2.2.54.1.1.1.19
This object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListType 1.3.6.1.4.1.4874.2.2.54.1.1.1.20
There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accessList(1), prefixList(2), noPolicyList(3)  

usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListType 1.3.6.1.4.1.4874.2.2.54.1.1.1.21
There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accessList(1), prefixList(2), noPolicyList(3)  

usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyList 1.3.6.1.4.1.4874.2.2.54.1.1.1.22
This object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyList 1.3.6.1.4.1.4874.2.2.54.1.1.1.23
This object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

usdMplsGroupTopologyDrivenLdp 1.3.6.1.4.1.4874.2.2.54.1.1.1.24
LDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsGroupLspLabelDistCtrlMode 1.3.6.1.4.1.4874.2.2.54.1.1.1.25
Some FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ordered(0), independent(1), undefined(2)  

usdMplsGroupLdpAdvHostOnly 1.3.6.1.4.1.4874.2.2.54.1.1.1.26
This object allows to enable/disable LDP label advertisement mode for host only LSPs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupLsrState 1.3.6.1.4.1.4874.2.2.54.1.1.1.27
This object value displays the status of MPLS enabled LSR such as state is up or down etc.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

usdMplsGroupReopNow 1.3.6.1.4.1.4874.2.2.54.1.1.1.28
All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

usdMplsGroupTargetedHelloSendTable 1.3.6.1.4.1.4874.2.2.54.1.1.2.1
This table contains list of send side IP addresses for LDP targeted hello messages.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsGroupTargetedHelloSendEntry

usdMplsGroupTargetedHelloSendEntry 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1
Each entry represents send IP address for targeted hello message.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsGroupTargetedHelloSendEntry  

usdMplsGroupTargetedHelloSendAddress 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1
Configure the send side address for targeted hello messages.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdMplsGroupLdpTargetedHelloSendMode 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2
Select mode to add/delete to the list of IP addresses for targeted hello messages.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER add(0), delete(1), none(2)  

usdMplsGroupTargetedHelloReceiveTable 1.3.6.1.4.1.4874.2.2.54.1.1.2.2
This table contains list of receive side IP addresses for LDP targeted hello messages.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsGroupTargetedHelloReceiveEntry

usdMplsGroupTargetedHelloReceiveEntry 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1
Each entry represents receive IP address for targeted hello message.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsGroupTargetedHelloReceiveEntry  

usdMplsGroupTargetedHelloReceiveAddress 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1
Configure the receive side address for targeted hello messages.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdMplsGroupLdpTargetedHelloReceiveMode 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2
Select mode to add/delete to the list of IP addresses for targeted hello messages.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER add(0), delete(1), none(2)  

usdMplsGroupLdpLabelAdverRouteListTable 1.3.6.1.4.1.4874.2.2.54.1.1.2.3
Table is a list of LDP label advertisement entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsGroupLdpLabelAdverRouteListEntry

usdMplsGroupLdpLabelAdverRouteListEntry 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1
Each entry represents access list pairs for the LDP peers label advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsGroupLdpLabelAdverRouteListEntry  

usdMplsGroupLdpLabelAdverRouteListName 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1
This LDP label advertisement route list name for which this entry contains information.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdMplsGroupLdpLabelAdverNbrListName 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2
The LDP label advertisement neighbor route list name for which this entry contains information.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

usdMplsGroupLabelAdverListMode 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3
This object selects the mode of addition/deletion to the list.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER add(0), delete(1), none(2)  

usdMplsGroupLdpProfileTable 1.3.6.1.4.1.4874.2.2.54.1.1.2.4
Table is a list of LDP Profile entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsGroupLdpProfileEntry

usdMplsGroupLdpProfileEntry 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1
Each entry represents one LDP profile settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsGroupLdpProfileEntry  

usdMplsGroupLdpProfileName 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1
LDP profile name identifies unique entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsGroupLdpProfileHelloHoldTime 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2
Configure the LDP peers hello hold time period.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..120  

usdMplsGroupLdpProfileCrLdpAdminState 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3
Enable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsGroupLdpProfileRowStatus 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsGroupLdpProfileCrLdpAdminState usdMplsGroupLdpProfileRowStatus
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsGroupRsvpProfileTable 1.3.6.1.4.1.4874.2.2.54.1.1.2.5
Table is a list of LDP Profile entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsGroupRsvpProfileEntry

usdMplsGroupRsvpProfileEntry 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1
Each entry represents one LDP profile settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsGroupRsvpProfileEntry  

usdMplsGroupRsvpProfileName 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1
The RSVP profile name identifies unique entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsGroupRsvpProfileRefreshPeriod 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2
Configure the time out period between the generation of two refresh messages.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..1000000000  

usdMplsGroupRsvpProfileCleanupTimeoutFactor 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3
Confgure the number of refresh messages can be lost before PATH or RESV state is ended.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..10  

usdMplsGroupRsvpProfileRowStatus 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsGroupRsvpProfileRowStatus
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsIfMajorNextIfIndex 1.3.6.1.4.1.4874.2.2.54.1.2.1.1
Coordinate ifIndex value allocation for entries in the usdMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdMplsIfMajorTable 1.3.6.1.4.1.4874.2.2.54.1.2.1.2
This table contains entries for MPLS Major interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsIfMajorEntry

usdMplsIfMajorEntry 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1
Each entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/usdIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsIfMajorEntry  

usdMplsIfMajorIndex 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1
The ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsIfMajorNextIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdMplsIfMajorRowStatus 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMajorRowStatus usdMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMajorIndex must have been determined previously, by reading usdMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsIfMajorLowerIfIndex 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3
The ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdMplsIfMajorAdminStatus 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4
Use this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsIfMajorLdpAdminStatus 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5
This object enables/disables LDP admin status on the MPLS interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsIfMajorLdpProfileName 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6
All the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsIfMajorLdpVpiStart 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7
This object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVpiRanges  

usdMplsIfMajorLdpVpiStop 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8
This object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVpiRanges  

usdMplsIfMajorLdpVciStart 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9
This object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVciRanges  

usdMplsIfMajorLdpVciStop 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10
This object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVciRanges  

usdMplsIfMajorRsvpAdminStatus 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11
This object configures RSVP admin status for MPLS interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsIfMajorRsvpProfileName 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12
All the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsIfMajorRsvpVpiStart 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13
This object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVpiRanges  

usdMplsIfMajorRsvpVpiStop 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14
This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVpiRanges  

usdMplsIfMajorRsvpVciStart 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15
This object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVciRanges  

usdMplsIfMajorRsvpVciStop 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16
This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMajorCfgVciRanges  

usdMplsIfMajorLabelSpaceType 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17
Displays the label space type for the MPLS interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), rsvpVpiVci(1), rsvpVpi(2), rsvpVci(3), ldpVpiVci(4), ldpVpi(5), ldpVci(6)  

usdMplsIfMajorOpState 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18
This object displays MPLS major interface operation state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lowerLayerNotAvailable(0), lowerLayerDown(1), up(2), configIncompleteInterfaceEnabled(3), configIncompleteInterfaceDisabled(4), interfaceDisabled(5)  

usdMplsIfMajorCrLdpAdminState 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19
This object displays the admin state of CR-LDP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsIfMinorNextIfIndex 1.3.6.1.4.1.4874.2.2.54.1.3.1.1
Coordinates ifIndex value allocation for entries in the usdMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdMplsIfMinorTable 1.3.6.1.4.1.4874.2.2.54.1.3.1.2
This table contains entries for MPLS Minor interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsIfMinorEntry

usdMplsIfMinorEntry 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1
Each entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsIfMinorEntry  

usdMplsIfMinorIndex 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1
The ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsMinorNextIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdMplsIfMinorRowStatus 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorRowStatus usdMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMinorIndex must have been determined previously, by reading usdMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsIfMinorLowerIfIndex 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3
The ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdMplsIfMinorAdminStatus 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4
With this object minor interface admin status can be enabled/disabled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsIfMinorEndpointAddress 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5
This object configures the IP address of the tunnel destination. This object can be set along with the usdMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsIfMinorEndpointDstMask 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6
This object configures the tunnel destination mask. It can be set along with the usdMplsIfMinorEndpointAddress.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsIfMinorTunnelMetricMode 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7
Select the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, usdMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, usdMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER absolute(0), relative(1)  

usdMplsIfMinorAbsoluteTunnelMetric 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8
This object allows configuration of absolute metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4294967295  

usdMplsIfMinorRelativeTunnelMetric 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9
This object allows configuration of relative metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -10..10  

usdMplsIfMinorLabelDistProto 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10
This object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER crLdp(0), rsvpTe(1), undefined(2)  

usdMplsIfMinorAnnounceToOspf 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11
This object allows to register LSP endpoints to OSPF to next hop calculation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorAnnounceToIsis 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12
This object allows to register LSP endpoints to IS-IS for next hop calculation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorAnnounceToBgp 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13
This object allows to register LSP endpoints to BGP for next hop calculation.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorBandwidth 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14
This object allows configuration of bandwidth requirements for the tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgBWRanges  

usdMplsIfMinorAffinity 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15
This object allows configuration of resource class affinity for the tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

usdMplsIfMinorAffinityMask 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16
This allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

usdMplsIfMinorSetupPriority 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17
This object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgHoldingAndSetupPriorityRanges  

usdMplsIfMinorHoldingPriority 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18
This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgHoldingAndSetupPriorityRanges  

usdMplsIfMinorTunnelName 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19
This object allows configuration of the tunnel name to be associated with tunnel settings.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsIfMinorTunnelRetryTimes 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20
This object allows configuration of the number of retries for tunnel setup.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgRetryTimesAndNorouteRanges  

usdMplsIfMinorTunnelRetryInterval 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21
This object allows configuration of retry interval for tunnel setup.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgRetryIntervalAndNorouteRanges  

usdMplsIfMinorTunnelRetryTimesNoroute 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22
This object allows configuration of the tunnel retries when no route notifications are received.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgRetryTimesAndNorouteRanges  

usdMplsIfMinorTunnelRetryIntervalNoroute 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23
This object allows configuration of the tunnel retry interval when no route notifications are received.
Status: current Access: read-create
OBJECT-TYPE    
  UsdMinorCfgRetryIntervalAndNorouteRanges  

usdMplsIfMinorBaseTunnelName 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24
This object allows configuration of the base tunnel name over which all the tunnels are stacked over.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

usdMplsIfMinorVpnOuiNumber 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25
This object allows configuration of the OUI part of VPN ID.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16777215  

usdMplsIfMinorVpnIndex 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26
This object allows configuration of the index part of VPN ID.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsIfMinorTunnelOpState 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27
This object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no change
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER established(0), teNegotiation(1), up(2), down(3), cfgChanged(4), cfgIncEn(5), cfgIncDis(6), disabled(7), rel(8), noChange(9)  

usdMplsIfMinorTargetedDynamicTunnel 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28
Configure targeted dynamic tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorReoptimization 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29
Configure tunnel reoptimization.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorPathOptionTable 1.3.6.1.4.1.4874.2.2.54.1.3.2.1
Table is a list of different LSP paths as option for each LSP setup.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsIfMinorPathOptionEntry

usdMplsIfMinorPathOptionEntry 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1
Each entry represents one path option for the LSP.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsIfMinorPathOptionEntry  

usdMplsIfMinorPathOptionIndex 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1
Minor interface uid.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdMplsIfMinorPathOptionNumber 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2
Unique number to identify each path option configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1000  

usdMplsIfMinorPathOptionProtocol 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3
Select the each path option explicit routing protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hopByHop(0), isis(1), ospf(2), none(3)  

usdMplsIfMinorPathOptionLockdown 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4
Enable/disable each configured path option reoptimization.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsIfMinorPathOptionPathName 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5
Configure the name for each path option.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsIfMinorPathOptionPathId 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6
Configure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

usdMplsIfMinorPathOptionRowStatus 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorPathOptionRowStatus.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsTunnelProfileTable 1.3.6.1.4.1.4874.2.2.54.1.4.1.1
Table is a list of tunnel profiles for a given VR.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsTunnelProfileEntry

usdMplsTunnelProfileEntry 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1
Each entry represents one tunnel profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsTunnelProfileEntry  

usdMplsTunnelProfileName 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1
Associate a name for the configured tunnel profile settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfileAdminStatus 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2
Enable/disable the adminstatus of the tunnel profile.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsTunnelProfileBaseTunnelName 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3
Configure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

usdMplsTunnelProfileIpProfileName 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4
Configures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfileLabelDistProto 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5
Configure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER crLdp(0), rsvpTe(1), undefined(2)  

usdMplsTunnelProfileAnnounceToOspf 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6
Configure the routing protocol for next hop calculations as OSPF.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsTunnelProfileAnnounceToIsis 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7
Configure routing protocol for next hop calculations as ISIS.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsTunnelProfileAnnounceToBgp 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8
Configure routing protocol for next hop calculations as BGP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsTunnelProfileMetricMode 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9
Select the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, usdMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, usdMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER absolute(0), relative(1)  

usdMplsTunnelProfileAbsoluteMetric 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10
This object allows configuration of the absolute metric values. Refer to usdMplsTunnelProfileMetricMode for how set it.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4294967295  

usdMplsTunnelProfileRelativeMetric 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11
This object allows configuration of the relative metric values. Refer to usdMplsTunnelProfileMetricMode for how set it.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -10..10  

usdMplsTunnelProfileBandwidth 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12
This object allows configuration of bandwidth requirements for the tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgBWRanges  

usdMplsTunnelProfileAffinity 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13
This object allows configuration of the resource class affinity for the tunnel. This can set independently of usdMplsTunnelProfileAffinityMask.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

usdMplsTunnelProfileAffinityMask 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14
This allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with usdMplsTunnelProfileAffinity. Specify the value in bit mask format.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

usdMplsTunnelProfileSetupPriority 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15
This object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgHoldingAndSetupPriorityRanges  

usdMplsTunnelProfileHoldingPriority 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16
This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgHoldingAndSetupPriorityRanges  

usdMplsTunnelProfileRetryTimes 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17
This object allows configuration of the number of retries for the tunnel setup.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgRetryTimesAndNorouteRanges  

usdMplsTunnelProfileRetryInterval 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18
This object allows configuration of retry interval for tunnel setup.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgRetryIntervalAndNorouteRanges  

usdMplsTunnelProfileRetryTimesNoroute 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19
This object allows configuration of the tunnel retries when no route notifications are received.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgRetryTimesAndNorouteRanges  

usdMplsTunnelProfileRetryIntervalNoroute 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20
This object allows configuration of the tunnel retry interval when no route notifications are received.
Status: current Access: read-create
OBJECT-TYPE    
  UsdProfileCfgRetryIntervalAndNorouteRanges  

usdMplsTunnelProfileVpnOuiNumber 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21
This object allows configuration of the OUI part of VPN ID.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16777215  

usdMplsTunnelProfileVpnIndex 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22
This object allows configuration of the index part of VPN ID.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsTunnelProfileRowStatus 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileRowStatus
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsTunnelProfileTargetedDynamicTunnel 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24
Configure targeted dynamic tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsTunnelProfilePathOptionTable 1.3.6.1.4.1.4874.2.2.54.1.4.2.1
Table is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsTunnelProfilePathOptionEntry

usdMplsTunnelProfilePathOptionEntry 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1
Each entry represents one path option for the LSP setup, configured as a part of tunnel profile settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsTunnelProfilePathOptionEntry  

usdMplsTunnelProfileNamePathOption 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1
Name of the path option.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfilePathOptionNumber 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2
Unique identifier for the path option.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1000  

usdMplsTunnelProfilePathOptionProtocol 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3
Path selection option protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hopByHop(0), isis(1), ospf(2), none(3)  

usdMplsTunnelProfilePathOptionLockdown 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4
Enable/disable path selection option reoptimization.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsTunnelProfilePathOptionPathName 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5
Associate a name with each explicit path.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfilePathOptionPathId 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6
Each explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

usdMplsTunnelProfilePathOptionRowStatus 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfilePathOptionRowStatus.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsTunnelProfileDynamicEndpointTable 1.3.6.1.4.1.4874.2.2.54.1.4.2.2
This table contains entries for the dynamic endpoints configured for each tunnel profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsTunnelProfileDynamicEndpointEntry

usdMplsTunnelProfileDynamicEndpointEntry 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1
Dynamic endpoint entries for each tunnel profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsTunnelProfileDynamicEndpointEntry  

usdMplsTunnelProfileNameDynamicEndpoint 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1
Configure the tunnel dynamic endpoint in tunnel profile settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfileDynamicEndpointType 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2
Configure the dynamic endpoint type for the tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER isisLevel2(0), ospfBorder(1)  

usdMplsTunnelProfileDynamicEndpointPolicyListType 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3
This object allows configuration of the dynamic tunnel policy type selection.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER accessList(1), prefixList(2), noPolicyList(3)  

usdMplsTunnelProfileDynamicEndpointListName 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4
This object allows configuration of the dynamic endpoints access list name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfileDynamicEndpointRowStatus 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsTunnelProfileDynamicEndpointRowStatus.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsTunnelProfileTunnelEndpointTable 1.3.6.1.4.1.4874.2.2.54.1.4.2.3
Table contains list of tunnel static enpoints configured for each tunnel profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsTunnelProfileTunnelEndpointEntry

usdMplsTunnelProfileTunnelEndpointEntry 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1
Each entry represents one static endpoint configuration for the tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsTunnelProfileTunnelEndpointEntry  

usdMplsTunnelProfileNameTunnelEndpoint 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1
This object configures the tunnel profile name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsTunnelProfileTunnelEndpointAddress 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2
This object configures the IP address of the tunnel destination.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdMplsTunnelProfileTunnelEndpointDstMask 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3
This object configures the tunnel destination mask.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdMplsTunnelProfileTunnelEndpointRowStatus 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileTunnelEndpointRowStatus.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsExplicitPathTable 1.3.6.1.4.1.4874.2.2.54.1.5.1.1
Table is a list of hops configurations for explicit paths.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsExplicitPathEntry

usdMplsExplicitPathEntry 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1
Each entry represents one hop configuration for the particular explicit path.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsExplicitPathEntry  

usdMplsExplicitPathName 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1
Configure the name for the explicit path used as table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsExplicitPathAdminState 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2
Enable/disable explicit path adminstatus.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

usdMplsExplicitPathRowStatus 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3
Creation/deletion of the explicit path is done through setting this object.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsExplicitPathNodeTable 1.3.6.1.4.1.4874.2.2.54.1.5.1.2
Table is a list of configured explicit paths.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdMplsExplicitPathNodeEntry

usdMplsExplicitPathNodeEntry 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1
Each entry represents one hop in a particular explicit path.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdMplsExplicitPathNodeEntry  

usdMplsExplicitPathNodeName 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1
Configure the name for the explicit path used in the table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..20)  

usdMplsExplicitPathNodeIndexNumber 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2
Each explicit path hop will have an index associated with it. Configure each path hop index using this object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

usdMplsExplicitPathNodeLoose 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3
Configure the explicit path hop as strict or loose. Set along with HopAddress.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdMplsExplicitPathNodeHopAddress 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4
Configure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsExplicitPathNodeHopAddressMask 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5
Configure the hop IP address mask. Set along with hop address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

usdMplsExplicitPathNodeRowStatus 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6
Use this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdMplsConformance 1.3.6.1.4.1.4874.2.2.54.2
OBJECT IDENTIFIER    

usdMplsCompliances 1.3.6.1.4.1.4874.2.2.54.2.1
OBJECT IDENTIFIER    

usdMplsConfGroups 1.3.6.1.4.1.4874.2.2.54.2.2
OBJECT IDENTIFIER    

usdMplsCompliance 1.3.6.1.4.1.4874.2.2.54.2.1.1
Obsolete compliance statement for entities which implement the Unisphere MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables.
Status: obsolete Access: read-create
MODULE-COMPLIANCE    

usdMplsCompliance2 1.3.6.1.4.1.4874.2.2.54.2.1.2
The compliance statement for entities which implement the Unisphere MPLS MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

usdMplsLsrGlobalConfGroup 1.3.6.1.4.1.4874.2.2.54.2.2.1
A collection of objects providing management of MPLS label switching routers (LSRs) in a Unisphere product.
Status: current Access: read-create
OBJECT-GROUP    

usdMplsMajorLayerConfGroup 1.3.6.1.4.1.4874.2.2.54.2.2.2
A collection of objects providing management of major MPLS interfaces in a Unisphere product.
Status: current Access: read-create
OBJECT-GROUP    

usdMplsMinorLayerConfGroup 1.3.6.1.4.1.4874.2.2.54.2.2.3
Obsolete collection of objects providing management of minor MPLS (tunnel) in a Unisphere product. This group became obsolete when the usdMplsIfMinorPathOptionRowStatus object was added.
Status: obsolete Access: read-create
OBJECT-GROUP    

usdMplsTunnelProfileConfGroup 1.3.6.1.4.1.4874.2.2.54.2.2.4
Obsolete collection of objects providing management of MPLS tunnel profiles in a Unisphere product. This group became obsolete when the objects usdMplsTunnelProfilePathOptionRowStatus, usdMplsTunnelProfileDynamicEndpointRowStatus and usdMplsTunnelProfileTunnelEndpointRowStatus were added.
Status: obsolete Access: read-create
OBJECT-GROUP    

usdMplsExplicitPathConfGroup 1.3.6.1.4.1.4874.2.2.54.2.2.5
A collection of objects providing management of MPLS explicit paths in a Unisphere product.
Status: current Access: read-create
OBJECT-GROUP    

usdMplsMinorLayerConfGroup2 1.3.6.1.4.1.4874.2.2.54.2.2.6
A collection of objects providing management of minor MPLS (tunnel) interfaces in a Unisphere product.
Status: current Access: read-create
OBJECT-GROUP    

usdMplsTunnelProfileConfGroup2 1.3.6.1.4.1.4874.2.2.54.2.2.7
A collection of objects providing management of MPLS tunnel profiles in a Unisphere product.
Status: current Access: read-create
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor