VERILINK-ENTERPRISE-NCMQUAD-MIB

File: VERILINK-ENTERPRISE-NCMQUAD-MIB.mib (43044 bytes)

Imported modules

RFC1155-SMI

Imported symbols

OBJECT-TYPE enterprises Gauge

Defined Types

NcmCSUConfigEntry  
SEQUENCE    
  ncmquadLineIndex INTEGER
  ncmquadIfIndex INTEGER
  ncmquadEndId INTEGER
  ncmquadPort INTEGER
  ncmquadLineType INTEGER
  ncmquadLineCoding INTEGER
  ncmquadFDL INTEGER
  ncmquadDensityPattern INTEGER
  ncmquadNetworkLineBuildOut INTEGER
  ncmquadNetworkLoopConfig INTEGER
  ncmquadLineStatus INTEGER
  ncmquadLoopbackConfig INTEGER
  ncmquadSendCode INTEGER
  ncmquadResetPerfReg INTEGER
  ncmquadValidIntervals INTEGER
  ncmquadTimeElapsed INTEGER
  ncmquadResetT1Error INTEGER

NcmCsuLossCurrentEntry  
SEQUENCE    
  ncmquadLCurrentIndex INTEGER
  ncmquadCurrentEndId INTEGER
  ncmquadLCurrentASs Gauge
  ncmquadLCurrentLOSs Gauge
  ncmquadLCurrentAISs Gauge
  ncmquadLCurrentLOFs Gauge
  ncmquadLCurrentOFs Gauge
  ncmquadLCurrentESs Gauge
  ncmquadLCurrentSESs Gauge
  ncmquadLCurrentSEFs Gauge
  ncmquadLCurrentUASs Gauge
  ncmquadLCurrentBESs Gauge
  ncmquadLCurrentESAs Gauge
  ncmquadLCurrentSASs Gauge
  ncmquadLCurrentCSSs Gauge
  ncmquadLCurrentLOFCs Gauge

NcmCsuLossIntervalEntry  
SEQUENCE    
  ncmquadLIntervalIndex INTEGER
  ncmquadLIntervalEndId INTEGER
  ncmquadLIntervalNumber INTEGER
  ncmquadLIntervalASs Gauge
  ncmquadLIntervalLOSs Gauge
  ncmquadLIntervalAISs Gauge
  ncmquadLIntervalLOFs Gauge
  ncmquadLIntervalOFs Gauge
  ncmquadLIntervalESs Gauge
  ncmquadLIntervalSESs Gauge
  ncmquadLIntervalSEFs Gauge
  ncmquadLIntervalUASs Gauge
  ncmquadLIntervalBESs Gauge
  ncmquadLIntervalESAs Gauge
  ncmquadLIntervalSASs Gauge
  ncmquadLIntervalCSSs Gauge
  ncmquadLIntervalLOFCs Gauge

NcmCsuLossTotalEntry  
SEQUENCE    
  ncmquadLTotalIndex INTEGER
  ncmquadTotalEndId INTEGER
  ncmquadLTotalASs Gauge
  ncmquadLTotalLOSs Gauge
  ncmquadLTotalAISs Gauge
  ncmquadLTotalLOFs Gauge
  ncmquadLTotalOFs Gauge
  ncmquadLTotalESs Gauge
  ncmquadLTotalSESs Gauge
  ncmquadLTotalSEFs Gauge
  ncmquadLTotalUASs Gauge
  ncmquadLTotalBESs Gauge
  ncmquadLTotalESAs Gauge
  ncmquadLTotalSASs Gauge
  ncmquadLTotalCSSs Gauge
  ncmquadLTotalLOFCs Gauge

NcmAdvancedT1ConfigEntry  
SEQUENCE    
  ncmadvancedT1LineIndex INTEGER
  ncmportIdentifier INTEGER
  ncmfdlMode INTEGER
  ncmfdlStandard INTEGER
  ncmfdlPerformanceReport INTEGER
  ncmfdlLBEnableDisable INTEGER
  ncmfdlLLBT1BOPMsg INTEGER
  ncmfdlPLBT1BOPMsg INTEGER
  ncmfdlIdlePattern INTEGER
  ncmfdlMonitoringCsuType INTEGER

NcmCSUSyncEntry  
SEQUENCE    
  ncmquadSyncIndex INTEGER
  ncmquadSyncEndId INTEGER
  ncmquadClkSyncSource INTEGER
  ncmquadClkCardPrim INTEGER
  ncmquadClkSyncPrimary INTEGER
  ncmquadAutoRestorePrim INTEGER
  ncmquadClkCardAlt1 INTEGER
  ncmquadClkSyncAlt1 INTEGER
  ncmquadAutoRestore1 INTEGER
  ncmquadClkCardAlt2 INTEGER
  ncmquadClkSyncAlt2 INTEGER
  ncmquadAutoRestore2 INTEGER

Defined Values


as2000 1.3.6.1.4.1.321.1
OBJECT IDENTIFIER    

ncm-quad 1.3.6.1.4.1.321.1.3009
OBJECT IDENTIFIER    

ncmquadConfigTable 1.3.6.1.4.1.321.1.3009.11000
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmCSUConfigEntry

ncmquadConfigEntry 1.3.6.1.4.1.321.1.3009.11000.1
An entry in the QUAD Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmCSUConfigEntry  

ncmquadLineIndex 1.3.6.1.4.1.321.1.3009.11000.1.1
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this and only this DS1 interface, it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadIfIndex 1.3.6.1.4.1.321.1.3009.11000.1.2
This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadEndId 1.3.6.1.4.1.321.1.3009.11000.1.3
This value for this object indicates which end of the equipment it is configuring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER near-End(0), far-End(1)  

ncmquadPort 1.3.6.1.4.1.321.1.3009.11000.1.4
This variable indicates Whether the port is in service or out of service
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ncmquadLineType 1.3.6.1.4.1.321.1.3009.11000.1.5
This variable indicates the variety of Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: ESF Extended SuperFrame DS1 D4 AT&T D4 format DS1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), eSF(2), d4(3)  

ncmquadLineCoding 1.3.6.1.4.1.321.1.3009.11000.1.6
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. B8ZS refers to the use of a specified pat- tern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(6), b8ZS(2), aMI(5)  

ncmquadFDL 1.3.6.1.4.1.321.1.3009.11000.1.7
The variable specifies the Disable/Enable of the ncmfdl State.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

ncmquadDensityPattern 1.3.6.1.4.1.321.1.3009.11000.1.8
This variable indicates what type of density network is being sent on the port or line by the device. The values mean : 'Disabled' refers to no network ones density exist. 'D80Zeros' refers to send a request for network one's density of 80 zeroes density pattern. 'D15Zeros' refers to send a request for network one's density of 15 zeroes density pattern. 'D12d5c80Zero'refers to send a request for 12.5% and 80 zeroes network one's density pattern. 'TR_62411' refers to sending a request for TR6241 network density pattern. 'Other' refers to sending a network's density pattern other than those described by this object[pvt]**.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER d80Zeros(1), d15Zeros(2), d12d5c80Zero(3), tR-62411(4), other(5), disabled(6)  

ncmquadNetworkLineBuildOut 1.3.6.1.4.1.321.1.3009.11000.1.9
This variable indicates the db rate at which the line or port using, i.e., is 0 , -7.5db, -15db or -22.5db.[pvt]
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bldLn-0db(1), bldLnNeg7d5db(2), bldLnNeg15db(3), bldLnNeg22d5(4)  

ncmquadNetworkLoopConfig 1.3.6.1.4.1.321.1.3009.11000.1.10
This variable represents whether the device can be configured throught the network for loopback. Here values mean : Disabled: This device cannot be loopbacked throught network. Enabled: This device can be loopbacked throught the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ncmquadLineStatus 1.3.6.1.4.1.321.1.3009.11000.1.11
This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. NoAlarms This variables indicates their is no alarms on this port or this line. Alarms This variables indicates their is alarms on line with any of the following bit map : The ncmquadLineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. If the ncmquadLoopbackState bit is set, the loopback in ef- fect can be determined from the ncmquadLoopbackConfig object. The various bit positions are: 0 Reserved 1 quadCRC6error (1 = yes, 0 = no) 2 Reserved 3 FramingSlip (1 = yes, 0 = no) 4 quadRAI (1 = yes, 0 = no) 5 quadLOF LOF (1 = yes, 0 = no) 6 quadAIS AIS (1 = yes, 0 = no) 7 quadLOS LOS (1 = yes, 0 = no) 8~15 ReservedForOtherFailure
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noAlarms(1), alarms(2)  

ncmquadLoopbackConfig 1.3.6.1.4.1.321.1.3009.11000.1.12
This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: quadNoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. quadPayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function. quadLineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out. quadLocalLoopbk This variable indicates whether the local loopback is enabled or disabled on the port or line by the device. quadOtherLoop Loopbacks that are not defined here.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noLoop(1), quadActPayloadLoop(2), quadDeactPayloadLoop(9), quadActLineLoop(3), quadDeactLineLoop(10), quadActLocalLoopbk(5), quadDeactLocalLoopbk(11), quadActLLBBOP(7), quadDeactLLBBOP(13), quadActPLBBOP(8), quadDeactPLBBOP(14)  

ncmquadSendCode 1.3.6.1.4.1.321.1.3009.11000.1.13
This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: NoCode sending looped or normal data QRSS sending a Quasi-Random Signal (QRSS) test pattern 3in24type sending a fixed test pattern of 3 bits set in 24 Other sending a test pattern other than those described by this object
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noCode(1), qRSS(5), three-in-24type(7), other(8)  

ncmquadResetPerfReg 1.3.6.1.4.1.321.1.3009.11000.1.14
Reset Performance Monitoring registers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ncmquadValidIntervals 1.3.6.1.4.1.321.1.3009.11000.1.15
The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

ncmquadTimeElapsed 1.3.6.1.4.1.321.1.3009.11000.1.16
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..899  

ncmquadResetT1Error 1.3.6.1.4.1.321.1.3009.11000.1.17
This variable indicates the option for reseting the T1 error counters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

ncmquadLossCurrentTable 1.3.6.1.4.1.321.1.3009.11001
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmCsuLossCurrentEntry

ncmquadLCurrentEntry 1.3.6.1.4.1.321.1.3009.11001.1
An entry in the Loss Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmCsuLossCurrentEntry  

ncmquadLCurrentIndex 1.3.6.1.4.1.321.1.3009.11001.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a ncmquadLineIndex object instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadCurrentEndId 1.3.6.1.4.1.321.1.3009.11001.1.2
This value for this object indicates which end of the equipment it is acessing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER near-End(0), far-End(1)  

ncmquadLCurrentASs 1.3.6.1.4.1.321.1.3009.11001.1.3
The number of Availabe Seconds, encountered by a DS1 interface in the current 15 minute inter- val. Remark: Available Seconds does not support for QUAD 2164.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentLOSs 1.3.6.1.4.1.321.1.3009.11001.1.4
The number of Loss Of Signal Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentAISs 1.3.6.1.4.1.321.1.3009.11001.1.5
The number of Alarm indication Signal Seconds encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentLOFs 1.3.6.1.4.1.321.1.3009.11001.1.6
The number of Loss of Frame Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentOFs 1.3.6.1.4.1.321.1.3009.11001.1.7
The number of Out of Frame Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentESs 1.3.6.1.4.1.321.1.3009.11001.1.8
The number of Errored Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentSESs 1.3.6.1.4.1.321.1.3009.11001.1.9
The number of Severely Errored Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentSEFs 1.3.6.1.4.1.321.1.3009.11001.1.10
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentUASs 1.3.6.1.4.1.321.1.3009.11001.1.11
The number of Out of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentBESs 1.3.6.1.4.1.321.1.3009.11001.1.12
The number of Bursty Errored Seconds encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentESAs 1.3.6.1.4.1.321.1.3009.11001.1.13
The number of ESAs encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentSASs 1.3.6.1.4.1.321.1.3009.11001.1.14
The number of SASs encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentCSSs 1.3.6.1.4.1.321.1.3009.11001.1.15
The number of CSSs encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLCurrentLOFCs 1.3.6.1.4.1.321.1.3009.11001.1.16
The number of LOFCs encountered by a DS1 interface in the current 15 minute in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLossIntervalTable 1.3.6.1.4.1.321.1.3009.11002
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmCsuLossIntervalEntry

ncmquadLIntervalEntry 1.3.6.1.4.1.321.1.3009.11002.1
An entry in the Loss Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmCsuLossIntervalEntry  

ncmquadLIntervalIndex 1.3.6.1.4.1.321.1.3009.11002.1.1
The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a ncmquadLineIndex object instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadLIntervalEndId 1.3.6.1.4.1.321.1.3009.11002.1.2
This value for this object indicates which end of the equipment it is accessing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER near-End(0), far-End(1)  

ncmquadLIntervalNumber 1.3.6.1.4.1.321.1.3009.11002.1.3
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

ncmquadLIntervalASs 1.3.6.1.4.1.321.1.3009.11002.1.4
The number of Available Seconds encountered by a DS1 interface in one of the previous 96, indi- vidual 15 minute, intervals. Remark: Available Seconds does not support for QUAD 2164.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalLOSs 1.3.6.1.4.1.321.1.3009.11002.1.5
The number of Loss of Signal Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalAISs 1.3.6.1.4.1.321.1.3009.11002.1.6
The number of Alarm Indication Signal Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalLOFs 1.3.6.1.4.1.321.1.3009.11002.1.7
The number of Loss Of Frame Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalOFs 1.3.6.1.4.1.321.1.3009.11002.1.8
The number of Out Of Frame Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalESs 1.3.6.1.4.1.321.1.3009.11002.1.9
The number of Error Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalSESs 1.3.6.1.4.1.321.1.3009.11002.1.10
The number of Severe Error Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalSEFs 1.3.6.1.4.1.321.1.3009.11002.1.11
The number of Severly Errored Frame Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalUASs 1.3.6.1.4.1.321.1.3009.11002.1.12
The number of Unavailable Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalBESs 1.3.6.1.4.1.321.1.3009.11002.1.13
The number of Bursty Error Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalESAs 1.3.6.1.4.1.321.1.3009.11002.1.14
The number of ESAs Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalSASs 1.3.6.1.4.1.321.1.3009.11002.1.15
The number of SASs encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalCSSs 1.3.6.1.4.1.321.1.3009.11002.1.16
The number of CSSs encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLIntervalLOFCs 1.3.6.1.4.1.321.1.3009.11002.1.17
The number of LOFCs encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLossTotalTable 1.3.6.1.4.1.321.1.3009.11003
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmCsuLossTotalEntry

ncmquadLTotalEntry 1.3.6.1.4.1.321.1.3009.11003.1
An entry in the DS1 Total Loss table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmCsuLossTotalEntry  

ncmquadLTotalIndex 1.3.6.1.4.1.321.1.3009.11003.1.1
The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a ncmquadLineIndex object instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadTotalEndId 1.3.6.1.4.1.321.1.3009.11003.1.2
This value for this object indicates which end of the equipment it is accessing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER near-End(0), far-End(1)  

ncmquadLTotalASs 1.3.6.1.4.1.321.1.3009.11003.1.3
The number of Available Seconds encountered by a DS1 interface in the previous 24 hour interval. Remark: Available Seconds does not support for QUAD 2164.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalLOSs 1.3.6.1.4.1.321.1.3009.11003.1.4
The number of Loss Of Signal Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalAISs 1.3.6.1.4.1.321.1.3009.11003.1.5
The number of Alarm Indication Signal Seconds encountered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalLOFs 1.3.6.1.4.1.321.1.3009.11003.1.6
The number of Loss Of Frame Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalOFs 1.3.6.1.4.1.321.1.3009.11003.1.7
The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalESs 1.3.6.1.4.1.321.1.3009.11003.1.8
The number of Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalSESs 1.3.6.1.4.1.321.1.3009.11003.1.9
The number of Severly Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalSEFs 1.3.6.1.4.1.321.1.3009.11003.1.10
The number of Severly Errored Frame Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalUASs 1.3.6.1.4.1.321.1.3009.11003.1.11
The number of Unavailable Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalBESs 1.3.6.1.4.1.321.1.3009.11003.1.12
The number of Bursty Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalESAs 1.3.6.1.4.1.321.1.3009.11003.1.13
The number of ESAs Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalSASs 1.3.6.1.4.1.321.1.3009.11003.1.14
The number of SASs encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalCSSs 1.3.6.1.4.1.321.1.3009.11003.1.15
The number of CSSs Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmquadLTotalLOFCs 1.3.6.1.4.1.321.1.3009.11003.1.16
The number of LOFCs Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ncmadvancedT1ConfigTable 1.3.6.1.4.1.321.1.3009.11004
The ncmadvanced T1 Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmAdvancedT1ConfigEntry

ncmadvancedT1ConfigEntry 1.3.6.1.4.1.321.1.3009.11004.1
An entry in the ncmadvanced T1 Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmAdvancedT1ConfigEntry  

ncmadvancedT1LineIndex 1.3.6.1.4.1.321.1.3009.11004.1.1
The index value which uniquely identifies the interface to which this entry is applicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmportIdentifier 1.3.6.1.4.1.321.1.3009.11004.1.2
The variable specifies the port identifier and port_3 and port_4 are for Quad T1 only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER port-1(0), port-2(1), port-3(2), port-4(3)  

ncmfdlMode 1.3.6.1.4.1.321.1.3009.11004.1.3
The variable specifies the ncmfdl mode which is bit 0 of ncmfdl Parameter1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER terminated(0), pass(1)  

ncmfdlStandard 1.3.6.1.4.1.321.1.3009.11004.1.4
The variable specifies the ncmfdl standard which is bits 1 and bit 2 of ncmfdl Parameter1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reserved(0), type-54016(4), type-T1-403(8), type-both(12)  

ncmfdlPerformanceReport 1.3.6.1.4.1.321.1.3009.11004.1.5
The variable specifies the ncmfdl standard which is bits 3 and bit 4 of ncmfdl Parameter1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), user(32), telco(64)  

ncmfdlLBEnableDisable 1.3.6.1.4.1.321.1.3009.11004.1.6
The variable specifies the Disable/Enable of the ncmfdl Loopback which is bit 0 of the ncmfdl_loop
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

ncmfdlLLBT1BOPMsg 1.3.6.1.4.1.321.1.3009.11004.1.7
The variable specifies the Disable/Enable of the send/receive of the LLB T1.403 BOP Messages. It is the bit 1 of the ncmfdl_loop
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(2)  

ncmfdlPLBT1BOPMsg 1.3.6.1.4.1.321.1.3009.11004.1.8
The variable specifies the Disable/Enable of the send/receive of the PLB T1.403 BOP Messages. It is the bit 2 of the ncmfdl_loop
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(4)  

ncmfdlIdlePattern 1.3.6.1.4.1.321.1.3009.11004.1.9
The variable specifies the ncmfdl idle pattern which is bit 0 of ncmfdl Parameter2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all-ones(0), flags(1)  

ncmfdlMonitoringCsuType 1.3.6.1.4.1.321.1.3009.11004.1.10
The variable specifies the ncmfdl standard which is bits 1 and bit 2 of ncmfdl Parameter2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER polling(0), no-polling(4), unsolicited-messages(8)  

ncmquadSyncTable 1.3.6.1.4.1.321.1.3009.11005
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NcmCSUSyncEntry

ncmquadSyncEntry 1.3.6.1.4.1.321.1.3009.11005.1
An entry in the QUAD Sync Time table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NcmCSUSyncEntry  

ncmquadSyncIndex 1.3.6.1.4.1.321.1.3009.11005.1.1
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this and only this DS1 interface, it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ncmquadSyncEndId 1.3.6.1.4.1.321.1.3009.11005.1.2
This value for this object indicates which end of the equipment it is configuring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER near-End(0), far-End(1)  

ncmquadClkSyncSource 1.3.6.1.4.1.321.1.3009.11005.1.3
This variable indicates Current Clk Source Active i.e., primary, Alt_1 or Alt_2 source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER primary(0), alt-1(1), alt-2(2)  

ncmquadClkCardPrim 1.3.6.1.4.1.321.1.3009.11005.1.4
This variable indicates the primary clock source from which card of the that shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER c-1(0), c-2(1), c-3(2), c-4(3), c-5(4), c-6(5), c-7(6), c-8(7), c-9(8), c-10(9), c-11(10), c-12(11), c-13(12)  

ncmquadClkSyncPrimary 1.3.6.1.4.1.321.1.3009.11005.1.5
This variable indicates the Clock source internal, external or network port. Setting Auto restore one can have auto restore Capability.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(0), external(1), masterNet1(2), masterNet2(3), masterNet3(4), masterNet4(5)  

ncmquadAutoRestorePrim 1.3.6.1.4.1.321.1.3009.11005.1.6
This variable indicates the Clock source auto restore or not for Internal, external or network clocks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ncmquadClkCardAlt1 1.3.6.1.4.1.321.1.3009.11005.1.7
This variable indicates the primary clock source from which card of the that shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER c-1(0), c-2(1), c-3(2), c-4(3), c-5(4), c-6(5), c-7(6), c-8(7), c-9(8), c-10(9), c-11(10), c-12(11), c-13(12)  

ncmquadClkSyncAlt1 1.3.6.1.4.1.321.1.3009.11005.1.8
This variable indicates the Clock source internal, external or network port. Setting Auto restore one can have auto restore Capability.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(0), external(1), masterNet1(2), masterNet2(3), masterNet3(4), masterNet4(5)  

ncmquadAutoRestore1 1.3.6.1.4.1.321.1.3009.11005.1.9
This variable indicates the Clock source auto restore or not for Internal, external or network clocks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ncmquadClkCardAlt2 1.3.6.1.4.1.321.1.3009.11005.1.10
This variable indicates the primary clock source from which card of the that shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER c-1(0), c-2(1), c-3(2), c-4(3), c-5(4), c-6(5), c-7(6), c-8(7), c-9(8), c-10(9), c-11(10), c-12(11), c-13(12)  

ncmquadClkSyncAlt2 1.3.6.1.4.1.321.1.3009.11005.1.11
This variable indicates the Clock source internal, external or network port. Setting Auto restore one can have auto restore Capability.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(0), external(1), masterNet1(2), masterNet2(3), masterNet3(4), masterNet4(5)  

ncmquadAutoRestore2 1.3.6.1.4.1.321.1.3009.11005.1.12
This variable indicates the Clock source auto restore or not for Internal, external or network clocks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor