WHISP-BOX-MIBV2-MIB

File: WHISP-BOX-MIBV2-MIB.mib (168222 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
WHISP-TCV2-MIB WHISP-GLOBAL-REG-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Counter64 Gauge32 IpAddress
NOTIFICATION-TYPE Unsigned32 DisplayString
MacAddress OBJECT-GROUP WhispLUID
WhispMACAddress EventString whispModules
whispBox

Defined Types

WhispBoxRFPhysicalRadioEntry  
SEQUENCE    
  radioIndex INTEGER
  radioType INTEGER
  radioPaths INTEGER

WhispBoxRFPhysicalRadioPathEntry  
SEQUENCE    
  pathIndex INTEGER

WhispBoxRFPhysicalRadioFrequencyEntry  
SEQUENCE    
  frequency INTEGER

WhispBoxRFConfigRadioEntry  
SEQUENCE    
  radioConfigIndex INTEGER
  radioFrequencyBand INTEGER

WhispBoxBridgeEntry  
SEQUENCE    
  whispBridgeMacAddr MacAddress
  whispBridgeDesLuid WhispLUID
  whispBridgeAge INTEGER
  whispBridgeExt INTEGER
  whispBridgeHash INTEGER
  whispBridgeCAM INTEGER

WhispVLANEntry  
SEQUENCE    
  whispVID INTEGER
  whispVType DisplayString
  whispVAge INTEGER

WhispVLANRemarkEntry  
SEQUENCE    
  sourceVID INTEGER
  remarkVIDState DisplayString
  remarkVID INTEGER
  remarkPriorityState DisplayString
  remarkPriority INTEGER

WhispUserEntry  
SEQUENCE    
  entryIndex INTEGER
  userLoginName DisplayString
  userPswd DisplayString
  accessLevel INTEGER
  loginStatus INTEGER
  loginMethod INTEGER
  sessionTime INTEGER

WhispLayer2NeighborEntry  
SEQUENCE    
  entryL2Index INTEGER
  neighborMAC DisplayString
  neighborIP DisplayString
  neighborSiteName DisplayString

Defined Values

whispBoxLevelMibModule 1.3.6.1.4.1.161.19.1.1.8
This module contains generic Box-Level MIB definitions for Canopy Radios.
MODULE-IDENTITY    

whispBoxStatus 1.3.6.1.4.1.161.19.3.3.1
OBJECT IDENTIFIER    

whispBoxConfig 1.3.6.1.4.1.161.19.3.3.2
OBJECT IDENTIFIER    

whispBoxControls 1.3.6.1.4.1.161.19.3.3.3
OBJECT IDENTIFIER    

whispBoxEventLog 1.3.6.1.4.1.161.19.3.3.5
OBJECT IDENTIFIER    

whispBoxConf 1.3.6.1.4.1.161.19.3.3.6
OBJECT IDENTIFIER    

whispBoxGroups 1.3.6.1.4.1.161.19.3.3.6.1
OBJECT IDENTIFIER    

whispBoxBridgeVar 1.3.6.1.4.1.161.19.3.3.7
OBJECT IDENTIFIER    

whispBoxCPVar 1.3.6.1.4.1.161.19.3.3.9
OBJECT IDENTIFIER    

whispBoxEvent 1.3.6.1.4.1.161.19.3.3.12
OBJECT IDENTIFIER    

whispBoxDHCPClientEvent 1.3.6.1.4.1.161.19.3.3.12.1
OBJECT IDENTIFIER    

whispBoxDNS 1.3.6.1.4.1.161.19.3.3.13
OBJECT IDENTIFIER    

whispBoxSNMPv3 1.3.6.1.4.1.161.19.3.3.14
OBJECT IDENTIFIER    


whispBoxLinkTestConfig 1.3.6.1.4.1.161.19.3.3.18.1
OBJECT IDENTIFIER    

whispBoxLinkTestResult 1.3.6.1.4.1.161.19.3.3.18.2
OBJECT IDENTIFIER    

whispBoxRFPhysical 1.3.6.1.4.1.161.19.3.3.15
OBJECT IDENTIFIER    

whispBoxRFConfig 1.3.6.1.4.1.161.19.3.3.16
OBJECT IDENTIFIER    

whispBoxSoftwareVer 1.3.6.1.4.1.161.19.3.3.1.1
Version of software. Should be noted in the event customer has technical difficulties and need to contact technical support.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxFPGAVer 1.3.6.1.4.1.161.19.3.3.1.2
Version of FPGA.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxEsn 1.3.6.1.4.1.161.19.3.3.1.3
Electronic serial number(MAC address) assigned to Radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxBoot 1.3.6.1.4.1.161.19.3.3.1.4
Software boot version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

boxTemperature 1.3.6.1.4.1.161.19.3.3.1.5
Radio temperature.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

boxDeviceType 1.3.6.1.4.1.161.19.3.3.1.6
The type of the device.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

boxDeviceTypeID 1.3.6.1.4.1.161.19.3.3.1.7
Device type ID.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

boxEncryption 1.3.6.1.4.1.161.19.3.3.1.8
Device encryption type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

etherLinkStatus 1.3.6.1.4.1.161.19.3.3.1.9
Ethernet link status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

boxFrequency 1.3.6.1.4.1.161.19.3.3.1.10
Frequency band of the device.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

platformVer 1.3.6.1.4.1.161.19.3.3.1.11
Hardware platform version. For internal use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

platformType 1.3.6.1.4.1.161.19.3.3.1.12
Platform type: Canopy, Canopy Lite, Canopy Lite - Advantage, Advantage, Russian, Russian - Advantage.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dhcpLanIp 1.3.6.1.4.1.161.19.3.3.1.13
LAN interface IP obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpLanSubnetMask 1.3.6.1.4.1.161.19.3.3.1.14
LAN interface Subnet Mask obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpLanGateway 1.3.6.1.4.1.161.19.3.3.1.15
LAN interface Gateway obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRfPublicIp 1.3.6.1.4.1.161.19.3.3.1.16
RF Public interface IP obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRfPublicSubnetMask 1.3.6.1.4.1.161.19.3.3.1.17
RF Public interface Subnet Mask obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRfPublicGateway 1.3.6.1.4.1.161.19.3.3.1.18
RF Public interface Gateway obtained through DHCP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

lanDhcpStatus 1.3.6.1.4.1.161.19.3.3.1.19
Display LAN interface current DHPC status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rfPublicDhcpStatus 1.3.6.1.4.1.161.19.3.3.1.20
Display RF Public interface current DHPC status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

inSyncCount 1.3.6.1.4.1.161.19.3.3.1.21
Counter for number of In Synchronization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

outSyncCount 1.3.6.1.4.1.161.19.3.3.1.22
Counter for number of Out of Synchronization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pllOutLockCount 1.3.6.1.4.1.161.19.3.3.1.23
Counter for number of PLL out of Lock.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

txCalFailure 1.3.6.1.4.1.161.19.3.3.1.24
Counter for number of TX Calibration failure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swVersion 1.3.6.1.4.1.161.19.3.3.1.25
Software version information.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pldVersion 1.3.6.1.4.1.161.19.3.3.1.26
PLD version information.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

platformInfo 1.3.6.1.4.1.161.19.3.3.1.27
Platform information.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

antPolarization 1.3.6.1.4.1.161.19.3.3.1.28
Antenna polarization for FSK radios.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

packetOverloadCounter 1.3.6.1.4.1.161.19.3.3.1.29
Total packet overload count.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

whispBoxP11Personality 1.3.6.1.4.1.161.19.3.3.1.30
Board Personality Configuration of P11 and P12 radios.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxP11FPGAType 1.3.6.1.4.1.161.19.3.3.1.31
FPGA Type on P11 and P12 radios.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxP11BstrapFPGAVer 1.3.6.1.4.1.161.19.3.3.1.32
P11 Bootstrap FPGA Version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

numDFSDetections 1.3.6.1.4.1.161.19.3.3.1.33
Number of DFS Detections since last boot.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rxOverrunPkts 1.3.6.1.4.1.161.19.3.3.1.34
Counter for number of received overrun packets error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

boxTemperatureC 1.3.6.1.4.1.161.19.3.3.1.35
Radio temperature in Celsius.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

boxTemperatureF 1.3.6.1.4.1.161.19.3.3.1.36
Radio temperature in Fahrenheit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

bridgeCbFecStatbin 1.3.6.1.4.1.161.19.3.3.1.37
Bridge CB FEC Stats bin
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatbout 1.3.6.1.4.1.161.19.3.3.1.38
Bridge CB FEC Stats bout
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatbtoss 1.3.6.1.4.1.161.19.3.3.1.39
Bridge CB FEC Stats btoss
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatbtosscap 1.3.6.1.4.1.161.19.3.3.1.40
Bridge CB FEC Stats btosscap
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatuin 1.3.6.1.4.1.161.19.3.3.1.41
Bridge CB FEC Stats uin
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatuout 1.3.6.1.4.1.161.19.3.3.1.42
Bridge CB FEC Stats uout
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatutoss 1.3.6.1.4.1.161.19.3.3.1.43
Bridge CB FEC Stats utoss
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbFecStatutosscap 1.3.6.1.4.1.161.19.3.3.1.44
Bridge CB FEC Stats utosscap
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatbin 1.3.6.1.4.1.161.19.3.3.1.45
Bridge CB RF Stats bin
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatbout 1.3.6.1.4.1.161.19.3.3.1.46
Bridge CB RF Stats bout
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatbtoss 1.3.6.1.4.1.161.19.3.3.1.47
Bridge CB RF Stats btoss
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatbtosscap 1.3.6.1.4.1.161.19.3.3.1.48
Bridge CB RF Stats btosscap
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatuin 1.3.6.1.4.1.161.19.3.3.1.49
Bridge CB RF Stats uin
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatuout 1.3.6.1.4.1.161.19.3.3.1.50
Bridge CB RF Stats uout
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatutoss 1.3.6.1.4.1.161.19.3.3.1.51
Bridge CB RF Stats utoss
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatutosscap 1.3.6.1.4.1.161.19.3.3.1.52
Bridge CB RF Stats utosscap
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatNI1QSend 1.3.6.1.4.1.161.19.3.3.1.53
Bridge CB Error Stats ErrNI1QSend
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatNI2QSend 1.3.6.1.4.1.161.19.3.3.1.54
Bridge CB Error Stats ErrNI2QSend
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatBridgeFull 1.3.6.1.4.1.161.19.3.3.1.55
Bridge CB Error Stats BridgeFull
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatSendMsg 1.3.6.1.4.1.161.19.3.3.1.56
Bridge CB Error Stats SendMsg
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatAPFecQSend 1.3.6.1.4.1.161.19.3.3.1.57
Bridge CB Error Stats APFecQSend
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbErrStatApRfQSend 1.3.6.1.4.1.161.19.3.3.1.58
Bridge CB Error Stats ApRfQSend
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatXmtUDataCnt 1.3.6.1.4.1.161.19.3.3.1.59
RF Scheduler Stats Transmit Unicast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatXmtBDataCnt 1.3.6.1.4.1.161.19.3.3.1.60
RF Scheduler Stats Transmit Broadcast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvUDataCnt 1.3.6.1.4.1.161.19.3.3.1.61
RF Scheduler Stats Receive Unicast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvBDataCnt 1.3.6.1.4.1.161.19.3.3.1.62
RF Scheduler Stats Receive Broadcast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatXmtCntlCnt 1.3.6.1.4.1.161.19.3.3.1.63
RF Scheduler Stats Transmit Control Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvCntlCnt 1.3.6.1.4.1.161.19.3.3.1.64
RF Scheduler Stats Receive Control Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatInSyncCount 1.3.6.1.4.1.161.19.3.3.1.65
RF Scheduler Stats In Sync Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatOutSyncCount 1.3.6.1.4.1.161.19.3.3.1.66
RF Scheduler Stats Out Sync Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatOverrunCount 1.3.6.1.4.1.161.19.3.3.1.67
RF Scheduler Stats Overrun Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatUnderrunCount 1.3.6.1.4.1.161.19.3.3.1.68
RF Scheduler Stats Underrun Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvCorruptDataCount 1.3.6.1.4.1.161.19.3.3.1.69
RF Scheduler Stats Receive Corrupt Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatBadBcastCtlCnt 1.3.6.1.4.1.161.19.3.3.1.70
RF Scheduler Stats Bad Broadcast Control Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatPLLOutOfLockCnt 1.3.6.1.4.1.161.19.3.3.1.71
RF Scheduler Stats PLL Out of Lock Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatBeaconVerMismatchCnt 1.3.6.1.4.1.161.19.3.3.1.72
RF Scheduler Stats Beacon version Mismatch Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatBadFreqBcnRcvCnt 1.3.6.1.4.1.161.19.3.3.1.73
RF Scheduler Stats Wrong Frequency Beacon Received Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatnonLiteBcnRcvCnt 1.3.6.1.4.1.161.19.3.3.1.74
RF Scheduler Stats Non Lite Beacon Received Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatUnsupFeatBcnRcvCnt 1.3.6.1.4.1.161.19.3.3.1.75
RF Scheduler Stats Unsupported Feature Beacon Received Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatUnkwnFeatBcnRcvCnt 1.3.6.1.4.1.161.19.3.3.1.76
RF Scheduler Stats Unknown Feature Beacon Received Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatTxCalFailCnt 1.3.6.1.4.1.161.19.3.3.1.77
RF Scheduler Stats TX Calibration Failures Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatBadInSyncIDRcv 1.3.6.1.4.1.161.19.3.3.1.78
RF Scheduler Stats Bad In Sync ID Received Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatTempOutOfRange 1.3.6.1.4.1.161.19.3.3.1.79
RF Scheduler Stats Temperature Out of Range Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRSSIOutOfRange 1.3.6.1.4.1.161.19.3.3.1.80
RF Scheduler Stats RSSI Out of Range Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRangeCapEnf 1.3.6.1.4.1.161.19.3.3.1.81
RF Scheduler Stats Range Cap Enforced Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvLTStart 1.3.6.1.4.1.161.19.3.3.1.82
RF Scheduler Stats Rcv LT Start Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvLTStartHS 1.3.6.1.4.1.161.19.3.3.1.83
RF Scheduler Stats Rcv LT Start HS Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvLTResult 1.3.6.1.4.1.161.19.3.3.1.84
RF Scheduler Stats Rcv LT Result Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatXmtLTResult 1.3.6.1.4.1.161.19.3.3.1.85
RF Scheduler Stats Xmt LT Result Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

whispFeatureKeyOrigin 1.3.6.1.4.1.161.19.3.3.1.86
Origin of Feature Key which includes GMT time and location of the Key programming (if time is 0 the key was converted locally)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioMSN 1.3.6.1.4.1.161.19.3.3.1.87
MSN of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

updateStatus 1.3.6.1.4.1.161.19.3.3.1.88
Current Status of Device Update
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

syslogStatTxSuccesses 1.3.6.1.4.1.161.19.3.3.1.89
The count of Syslog messages sent to UDP layer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

syslogStatDropped 1.3.6.1.4.1.161.19.3.3.1.90
Number of dropped syslog messages due to device overload and/or resource limitations.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fecStatLinkLost 1.3.6.1.4.1.161.19.3.3.1.91
Ethernet link lost count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecStatLinkDetected 1.3.6.1.4.1.161.19.3.3.1.92
Ethernet link detected count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

natDhcpStatus 1.3.6.1.4.1.161.19.3.3.1.93
Display NAT Public interface current DHPC status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fecInDiscardsCount 1.3.6.1.4.1.161.19.3.3.1.94
Ethernet in discards count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

fecInErrorsCount 1.3.6.1.4.1.161.19.3.3.1.95
Ethernet in errors count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

fecOutDiscardsCount 1.3.6.1.4.1.161.19.3.3.1.96
Ethernet out discards count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

fecOutErrorsCount 1.3.6.1.4.1.161.19.3.3.1.97
Ethernet out errors count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

rfInDiscardsCount 1.3.6.1.4.1.161.19.3.3.1.98
RF in discards count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

rfInErrorsCount 1.3.6.1.4.1.161.19.3.3.1.99
RF in errors count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

rfOutDiscardsCount 1.3.6.1.4.1.161.19.3.3.1.100
RF out discards count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

rfOutErrorsCount 1.3.6.1.4.1.161.19.3.3.1.101
RF out errors count.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

fecInDiscardsOverloadCount 1.3.6.1.4.1.161.19.3.3.1.102
Ethernet in discards overload.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecOutDiscardsOverloadCount 1.3.6.1.4.1.161.19.3.3.1.103
Ethernet out discards overload.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfInDiscardsOverloadCount 1.3.6.1.4.1.161.19.3.3.1.104
Rf in discards overload.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfOutDiscardsOverloadCount 1.3.6.1.4.1.161.19.3.3.1.105
Rf out discards overload.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fpgaCompileInfo 1.3.6.1.4.1.161.19.3.3.1.106
Display the fpga compiled attributes. (Engineering Only)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fpgaBuildDate 1.3.6.1.4.1.161.19.3.3.1.107
Display the entire fpga build date string. (Engineering Only)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

aggregateBandwidthCap 1.3.6.1.4.1.161.19.3.3.1.108
The maximum aggregate (uplink + downlink) the radio is capable of.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

calibrationStatusBool 1.3.6.1.4.1.161.19.3.3.1.109
Boolean OID to show if device is calibrated. Applicable to FSK and MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notCalibrated(0), calibrated(1)  

calibrationStatusBox 1.3.6.1.4.1.161.19.3.3.1.110
String to show if radio is calibrated. Applicable to FSK and MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioEngKeyed 1.3.6.1.4.1.161.19.3.3.1.111
This will be set either as 0 if the engineering key patch is not applied to the radio or 1 if it is applied.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

bridgeCbFecStatfloods 1.3.6.1.4.1.161.19.3.3.1.112
Bridge CB RF Stats Floods (Multipoint AP only)
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgeCbRFStatfloods 1.3.6.1.4.1.161.19.3.3.1.113
Bridge CB RF Stats Floods (Multipoint AP only)
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

catalinaGainRxCH1 1.3.6.1.4.1.161.19.3.3.1.114
Rcv Gain on Catalina Rx CH1. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaGainRxCH2 1.3.6.1.4.1.161.19.3.3.1.115
Rcv Gain on Catalina Rx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

antType 1.3.6.1.4.1.161.19.3.3.1.116
Indicates whether the antenna is integrated or external (connectorized).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER integrated(0), external(1)  

rfStatRcvCorruptControlCount 1.3.6.1.4.1.161.19.3.3.1.117
RF Scheduler Stats Receive Corrupt Control Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

numLBTDetections 1.3.6.1.4.1.161.19.3.3.1.118
Number of LBT Detections since last boot.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

catalinaAttenTxCH1 1.3.6.1.4.1.161.19.3.3.1.121
Attenuation on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaAttenTxCH2 1.3.6.1.4.1.161.19.3.3.1.122
Attenuation on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetSetpointTxCH1 1.3.6.1.4.1.161.19.3.3.1.123
Current Detector Setpoint on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetSetpointTxCH2 1.3.6.1.4.1.161.19.3.3.1.124
Current Detector Setpoint on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetReadRefTxCH1 1.3.6.1.4.1.161.19.3.3.1.125
Current Detector Reference on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetReadRefTxCH2 1.3.6.1.4.1.161.19.3.3.1.126
Current Detector Reference on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetReadPowerOnTxCH1 1.3.6.1.4.1.161.19.3.3.1.127
Current Detector PowerOn on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaCurrDetReadPowerOnTxCH2 1.3.6.1.4.1.161.19.3.3.1.128
Current Detector PowerOn on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaOpenLoopAttenTxCH1 1.3.6.1.4.1.161.19.3.3.1.129
Open Loop Attenuation on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaOpenLoopAttenTxCH2 1.3.6.1.4.1.161.19.3.3.1.130
Open Loop Attenuation on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaTargetDetSetpointTxCH1 1.3.6.1.4.1.161.19.3.3.1.131
Target Detector Setpoint on Catalina Tx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaTargetDetSetpointTxCH2 1.3.6.1.4.1.161.19.3.3.1.132
Target Detector Setpoint on Catalina Tx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaGainReductionRxCH1 1.3.6.1.4.1.161.19.3.3.1.133
Gain Reduction on Catalina Rx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaGainReductionRxCH2 1.3.6.1.4.1.161.19.3.3.1.134
Gain Reduction on Catalina Rx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaLoAttenRxCH1 1.3.6.1.4.1.161.19.3.3.1.135
Lo Attenuation on Catalina Rx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaLoAttenRxCH2 1.3.6.1.4.1.161.19.3.3.1.136
Lo Attenuation on Catalina Rx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaTargetGainRxCH1 1.3.6.1.4.1.161.19.3.3.1.137
Target Gain on Catalina Rx CH1. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

catalinaTargetGainRxCH2 1.3.6.1.4.1.161.19.3.3.1.138
Target Gain on Catalina Rx CH2. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radioWatchDogLogged 1.3.6.1.4.1.161.19.3.3.1.147
This will be set either as 0 if there is no watchdog event logged or 1 if there is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radioFatalErrorLogged 1.3.6.1.4.1.161.19.3.3.1.148
This will be set either as 0 if there is no fatalerror event logged or 1 if there is.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rfStatXmtMDataCnt 1.3.6.1.4.1.161.19.3.3.1.217
RF Scheduler Stats Transmit Multicast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

rfStatRcvMDataCnt 1.3.6.1.4.1.161.19.3.3.1.218
RF Scheduler Stats Receive Multicast Data Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecStatUnderSizedToss 1.3.6.1.4.1.161.19.3.3.1.219
Undersized Toss Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecRxBabErr 1.3.6.1.4.1.161.19.3.3.1.220
Error count in Babble Receiver.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecTxHbErr 1.3.6.1.4.1.161.19.3.3.1.221
Number of packets having Transmit heartbeat error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecEthBusErr 1.3.6.1.4.1.161.19.3.3.1.222
Ethernet Busy Error Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecCRCError 1.3.6.1.4.1.161.19.3.3.1.223
Number of packets having CRC Error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecRxFifoNoBuf 1.3.6.1.4.1.161.19.3.3.1.224
Number of times could not get a buffer from Rx Fifo.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecRxOverrun 1.3.6.1.4.1.161.19.3.3.1.225
Number of times Rx Fifo Overrun.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecLateCollision 1.3.6.1.4.1.161.19.3.3.1.226
Number of packets having late collision.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecRetransLimitExp 1.3.6.1.4.1.161.19.3.3.1.227
Number of packets whose retransmision limit expired.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecTxUnderrun 1.3.6.1.4.1.161.19.3.3.1.228
Number of times Tx queue underrun.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecCarSenseLost 1.3.6.1.4.1.161.19.3.3.1.229
Carrier Sense Lost count.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fecNoCarrier 1.3.6.1.4.1.161.19.3.3.1.230
No carrier asserted by external transciever during transmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

framePeriodCurrent 1.3.6.1.4.1.161.19.3.3.1.231
Current frame period of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twoPointFiveMs(0), fiveMs(1), scanning(2)  

activeTxPowerStr 1.3.6.1.4.1.161.19.3.3.1.232
Current transmit power level, including potential power backoff information.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

activeTxPowerHdths 1.3.6.1.4.1.161.19.3.3.1.233
Current transmit power level, in hundredths of dBm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkNegoSpeed 1.3.6.1.4.1.161.19.3.3.2.1
Link negotiation speeds. H10BT -- 10 Base T Half Duplex, F10BT -- 10 Base T Full Duplex, H100BT -- 100 Base T Half Duplex, F100BT -- 100 Base T Full Duplex. Separate the values with comma when doing a set. e.g. H10BT,F10BT,H100BT,F100BT
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

colorCode 1.3.6.1.4.1.161.19.3.3.2.2
Color code.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

displayOnlyAccess 1.3.6.1.4.1.161.19.3.3.2.3
This variable is deprecated.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

fullAccess 1.3.6.1.4.1.161.19.3.3.2.4
Full access password.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

webAutoUpdate 1.3.6.1.4.1.161.19.3.3.2.5
Web page auto update in seconds. 0 means disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pass1Status 1.3.6.1.4.1.161.19.3.3.2.6
Password 1(display only) status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pass2Status 1.3.6.1.4.1.161.19.3.3.2.7
Password 2(full access) status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bridgeEntryTimeout 1.3.6.1.4.1.161.19.3.3.2.8
Bridge table time out Range : 25 -- 1440 Minutes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 25..1440  

snmpMibPerm 1.3.6.1.4.1.161.19.3.3.2.9
Read/Write permission for MIB groups.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER readWrite(0), readOnly(1)  

bhTimingMode 1.3.6.1.4.1.161.19.3.3.2.10
Variable to switch between Timing Master and Timing Slave. For Backhaul units only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER timingMaster(1), timeingSlave(0)  

bhModulation 1.3.6.1.4.1.161.19.3.3.2.11
Modulation scheme. For Backhaul units only. Only level 4 backhaul can be changed to 20Mbits/Second.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER tenMbitsPerSecond(0), twentyMbitsPerSecond(1)  

powerControl 1.3.6.1.4.1.161.19.3.3.2.12
Power control. FSK Only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER low(0), normal(1)  

extFilterDelay 1.3.6.1.4.1.161.19.3.3.2.13
Obsoleted. External Filters Delay. For 900MHz FSK radios only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

antennaGain 1.3.6.1.4.1.161.19.3.3.2.14
External Antenna Gain. For radios that uses an external antenna or the DFS feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

eirp 1.3.6.1.4.1.161.19.3.3.2.15
This variable is deprecated.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

dynamicLearning 1.3.6.1.4.1.161.19.3.3.2.16
To enable VLAN dynamic learning.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

managementVID 1.3.6.1.4.1.161.19.3.3.2.17
Management VLAN VID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

agingTimeout 1.3.6.1.4.1.161.19.3.3.2.18
Aging timeout.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

frameType 1.3.6.1.4.1.161.19.3.3.2.19
Allow only tagged frame.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allframes(0), taggedonly(1), untaggedonly(2)  

addVlanMember 1.3.6.1.4.1.161.19.3.3.2.20
Write-Only OID,Add VLAN number which needs to be added.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

removeVlanMember 1.3.6.1.4.1.161.19.3.3.2.21
Write-only OID,Enter VLAN ID which needs to deleted. If Vlan doesnot exist an error will be returned.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

scheduling 1.3.6.1.4.1.161.19.3.3.2.22
To use hardware or software scheduling
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hardware(1)  

transmitterOP 1.3.6.1.4.1.161.19.3.3.2.23
Transmitter output power. This is not available on OFDM SMs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

bridgeEnable 1.3.6.1.4.1.161.19.3.3.2.24
Disable or enable bridging functionality for a BH unit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(0), disable(1)  

fecEnable 1.3.6.1.4.1.161.19.3.3.2.25
Disable or enable FEC error correction functionality for multipoint units.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

trapIP1 1.3.6.1.4.1.161.19.3.3.2.26
Obsoleted. Configure with whispBoxDNS.trap1.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP2 1.3.6.1.4.1.161.19.3.3.2.27
Obsoleted. Configure with whispBoxDNS.trap2.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP3 1.3.6.1.4.1.161.19.3.3.2.28
Obsoleted. Configure with whispBoxDNS.trap3.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP4 1.3.6.1.4.1.161.19.3.3.2.29
Obsoleted. Configure with whispBoxDNS.trap4.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP5 1.3.6.1.4.1.161.19.3.3.2.30
Obsoleted. Configure with whispBoxDNS.trap5.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP6 1.3.6.1.4.1.161.19.3.3.2.31
Obsoleted. Configure with whispBoxDNS.trap6.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP7 1.3.6.1.4.1.161.19.3.3.2.32
Obsoleted. Configure with whispBoxDNS.trap7.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP8 1.3.6.1.4.1.161.19.3.3.2.33
Obsoleted. Configure with whispBoxDNS.trap8.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP9 1.3.6.1.4.1.161.19.3.3.2.34
Obsoleted. Configure with whispBoxDNS.trap9.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

trapIP10 1.3.6.1.4.1.161.19.3.3.2.35
Obsoleted. Configure with whispBoxDNS.trap10.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

commStringRWrite 1.3.6.1.4.1.161.19.3.3.2.36
Read/Write Community string. This is a write-only OID.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

subnetMask 1.3.6.1.4.1.161.19.3.3.2.37
Subnet mask for the management IP 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP 1.3.6.1.4.1.161.19.3.3.2.38
Management IP address 1.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

allowVIDAccess 1.3.6.1.4.1.161.19.3.3.2.39
Allow or disallow local SM management VID access.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(0), disable(1)  

setDefaultPlug 1.3.6.1.4.1.161.19.3.3.2.40
If enabled parameters are set to Factory Defaults upon default plug mode detection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hwsCompatibility 1.3.6.1.4.1.161.19.3.3.2.41
If enable, it ensures 6.0 compatibility with HWS.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enable(0), disable(1)  

gpsInput 1.3.6.1.4.1.161.19.3.3.2.42
Values 1, 2, 3 have been deprecated. (0) Generate AP sync signal. (1) Deprecated. Sync AP to received signal (Timing Port/UGPS). It will set AutoSync. (2) Deprecated. Sync AP to received signal (Power Port). It will set AutoSync plus Free Run. (3) Deprecated. Sync AP using iGPS (Only on devices which support it). It will set AutoSync plus Free Run. (4) AutoSync. (5) AutoSync plus Free Run.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER generateSyncSignal(0), syncToReceivedSignalTimingPort(1), syncToReceivedSignalPowerPort(2), syncToiGPS(3), autoSync(4), autoSyncFreeRun(5)  

ism 1.3.6.1.4.1.161.19.3.3.2.43
Enable ISM on 5.7GHz frequency band radios.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

hiPriority 1.3.6.1.4.1.161.19.3.3.2.44
Enable Hi Priority Data Queue on BH radios.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

userName 1.3.6.1.4.1.161.19.3.3.2.45
User name.To create read-only user set userMode OID first. Maximum of 4 users can exist in system.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

userPassword 1.3.6.1.4.1.161.19.3.3.2.46
User password.To create read-only user set userMode OID first.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

userAccessLevel 1.3.6.1.4.1.161.19.3.3.2.47
User access level.To create read-only user set userMode OID first. 1=TECH 2=INSTALL 3=ADMIN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

deleteUser 1.3.6.1.4.1.161.19.3.3.2.48
User name to remove.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

twoXRate 1.3.6.1.4.1.161.19.3.3.2.49
To enable or disable double rate.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

lanDhcpState 1.3.6.1.4.1.161.19.3.3.2.50
To enable or disable LAN Interface DHCP feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sessionTimeout 1.3.6.1.4.1.161.19.3.3.2.51
Timer for Telnet, Web and FTP sessions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vlanMemberSource 1.3.6.1.4.1.161.19.3.3.2.52
Specified the VLAN member source to display. 0=configured, 1=active configuration. Note that this OID is internal to SNMP and is not available at the Web Interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER configured(0), active(1)  

addCustomFreqList 1.3.6.1.4.1.161.19.3.3.2.53
Add Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be added in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequency list. Max string length entered cannot exceed 128 character. Note if there is not enough room for all the frequencies none will be added. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

removeCustomFreqList 1.3.6.1.4.1.161.19.3.3.2.54
Remove Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be removed in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequencies. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

allowColocation 1.3.6.1.4.1.161.19.3.3.2.55
Allow or disallow Colocation for software scheduling Backhaul Timing Masters with hardware scheduling Backhaul Timing Masters.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

changeUsrPwd 1.3.6.1.4.1.161.19.3.3.2.56
Allow to change the password of a given user of a given user. Usage: userName,password.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

mngtIP2 1.3.6.1.4.1.161.19.3.3.2.57
Management IP address 2.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask2 1.3.6.1.4.1.161.19.3.3.2.58
Subnet mask for the management IP 2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP3 1.3.6.1.4.1.161.19.3.3.2.59
Management IP address 3.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask3 1.3.6.1.4.1.161.19.3.3.2.60
Subnet mask for the management IP 3.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP4 1.3.6.1.4.1.161.19.3.3.2.61
Management IP address 4.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask4 1.3.6.1.4.1.161.19.3.3.2.62
Subnet mask for the management IP 4.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP5 1.3.6.1.4.1.161.19.3.3.2.63
Management IP address 5.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask5 1.3.6.1.4.1.161.19.3.3.2.64
Subnet mask for the management IP 5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP6 1.3.6.1.4.1.161.19.3.3.2.65
Management IP address 6.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask6 1.3.6.1.4.1.161.19.3.3.2.66
Subnet mask for the management IP 6.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP7 1.3.6.1.4.1.161.19.3.3.2.67
Management IP address 7.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask7 1.3.6.1.4.1.161.19.3.3.2.68
Subnet mask for the management IP 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP8 1.3.6.1.4.1.161.19.3.3.2.69
Management IP address 8.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask8 1.3.6.1.4.1.161.19.3.3.2.70
Subnet mask for the management IP 8.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP9 1.3.6.1.4.1.161.19.3.3.2.71
Management IP address 9.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask9 1.3.6.1.4.1.161.19.3.3.2.72
Subnet mask for the management IP 9.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mngtIP10 1.3.6.1.4.1.161.19.3.3.2.73
Management IP address 10.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask10 1.3.6.1.4.1.161.19.3.3.2.74
Subnet mask for the management IP 10.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

bhvlanEnable 1.3.6.1.4.1.161.19.3.3.2.75
To enable or disable VLAN for Backhaul Master/Slave.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpBroadcastEnable 1.3.6.1.4.1.161.19.3.3.2.76
To enable Broadcast of LLDP message, if disabled LLDP uses multicast
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

regionCode 1.3.6.1.4.1.161.19.3.3.2.77
Set Region Code for the Unit. Used the individual region[Region] OIDs instead.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER none(0), australia(6), brazil(5), canada(3), india(8), indonesia(10), ireland(11), russia(7), spain(9), us(2), other(1), europe(4)  

russiaRegion 1.3.6.1.4.1.161.19.3.3.2.78
Set Category Region for Russian 5.9/6.05 GHz Radio Only. Use setting under regionAsia now.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER category1(1), category2(2), category3(3), category4(4)  

commStringROnly 1.3.6.1.4.1.161.19.3.3.2.79
Set Read Only commnunity string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

ethernetLinkSpeed 1.3.6.1.4.1.161.19.3.3.2.80
Set/Get Ethernet link speed and duplex settings. Note that the Gigabit options are only valid for boards that support Gigabit speeds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forced10H(1), forced10F(2), forced100H(4), forced100F(8), auto10F-10H(3), auto100H-10H(5), auto100H-10F-10H(7), auto100F-100H(12), auto100F-100H-10H(13), auto100F-100H-10F-10H(15), auto1000F-100F-100H-10F-10H(63)  

cyclicPrefix 1.3.6.1.4.1.161.19.3.3.2.81
Cyclic Prefix value, for OFDM Radios only. Deprecated for MIMO SMs. For PMP 430 SMs, this value is only used while in PMP 430 mode (1/16 is forced in PMP 450 mode).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER one-quarter(0), one-eighth(1), one-sixteenth(2), one-quarter-one-eighth(3), one-quarter-one-sixteenth(4), one-eighth-one-sixteenth(5), one-quarter-one-eighth-one-sixteenth(6)  

numberCustomFreq 1.3.6.1.4.1.161.19.3.3.2.82
Number of custom frequencies added. There is a maximum of 100. For use on 3.5 GHz OFDM Radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

channelBandwidth 1.3.6.1.4.1.161.19.3.3.2.83
The current channel bandwidth in MHz. For use on OFDM Radios only. Obsoleted for MIMO SMs.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

setDefaults 1.3.6.1.4.1.161.19.3.3.2.84
Setting this to 1 will set the radio to Factory Defaults after the next reboot. Setting this to 0 will undo Factory Defaults if and only if Factory Defaults have been set previously without rebooting. Reading this OID will return 0 if Factory Defaults are not set, or a 2 if Factory Defaults are set and we are now awaiting a reboot. NOTE: this operation is reversible as long as you write a 0 to this OID prior to reboot. As a security measure, this OID is only valid when the radio was booted in default plug mode. If the radio is not currently in default plug mode, then attempting to set this OID will fail.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noChangeOrUndoFactoryDefaults(0), setToFactoryDefaults(1), factoryDefaultsSet-AwaitingReboot(2)  

radioRateAdapt 1.3.6.1.4.1.161.19.3.3.2.85
Rate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Downlink Rate Adapt only. Use radioRateAdaptUL for setting uplink rate adapt on PMP 430 radios. For PMP 450 radios, write access for engineering use only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER onex(0), onexmimo(4), onextwox(1), onextwoxmimo(5), onextwoxthreex(2), onextwoxthreexfourx(3), onextwoxfourx(7), onextwoxfourxsixx(8), onextwoxfourxsixxeightx(9), onextwoxmimoa(10), onextwoxthreexmimoa(11), onextwoxthreexfourxmimoa(12)  

siteInfoViewable 1.3.6.1.4.1.161.19.3.3.2.86
Enable non login users the ability to view Site Information
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

largeVCQ 1.3.6.1.4.1.161.19.3.3.2.87
Enable or disable Large VC Qs for SM or PTP radios. Enable when Uplink is being used for camera video feed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

latitude 1.3.6.1.4.1.161.19.3.3.2.88
The latitude setting of this unit in decimal degrees.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

longitude 1.3.6.1.4.1.161.19.3.3.2.89
The longitude setting of this unit in decimal degrees.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

height 1.3.6.1.4.1.161.19.3.3.2.90
The height setting of this unit in meters.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -2147483647..2147483647  

bandwidth 1.3.6.1.4.1.161.19.3.3.2.91
Radio bandwidth setting. Deprecated for MIMO SMs. Instead use bandwidthScan.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bandwidth5mhz(1), bandwidth7mhz(2), bandwidth10mhz(3), bandwidth20mhz(5), bandwidth5-10mhz(8), bandwidth5-20mhz(9), bandwidth10-20mhz(10), bandwidth5-10-20mhz(11), bandwidth5-7mhz(12), bandwidth7-10mhz(13), bandwidth7-20mhz(14), bandwidth7-10-20mhz(15), bandwidth5-7-10mhz(16), bandwidth5-7-20mhz(17), bandwidth5-7-10-20mhz(18)  

dataScramblingMethod 1.3.6.1.4.1.161.19.3.3.2.92
This OID is for OFDM only and is obsolete.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER legacyDataScrambling(0), r10DataScrambling(1)  

portVID 1.3.6.1.4.1.161.19.3.3.2.93
Backhaul Port VID (PVID).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radioRateAdaptUL 1.3.6.1.4.1.161.19.3.3.2.94
Uplink Rate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Uplink Rate Adapt only. Use radioRateAdapt for setting downlink rate adapt on PMP 430 radios. For PMP 450 radios, engineering use only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER onex(0), onexmimo(4), onextwox(1), onextwoxmimo(5), onextwoxthreex(2), onextwoxthreexfourx(3), onextwoxfourx(7), onextwoxfourxsixx(8), onextwoxfourxsixxeightx(9), onextwoxmimoa(10), onextwoxthreexmimoa(11), onextwoxthreexfourxmimoa(12)  

providerVID 1.3.6.1.4.1.161.19.3.3.2.95
Provider VID for QinQ VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mac1VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.96
MAC Address for Entry 1 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac1VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.97
VID for Entry 1 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac2VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.98
MAC Address for Entry 2 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac2VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.99
VID for Entry 2 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac3VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.100
MAC Address for Entry 3 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac3VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.101
VID for Entry 3 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac4VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.102
MAC Address for Entry 4 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac4VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.103
VID for Entry 4 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac5VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.104
MAC Address for Entry 5 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac5VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.105
VID for Entry 5 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac6VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.106
MAC Address for Entry 6 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac6VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.107
VID for Entry 6 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac7VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.108
MAC Address for Entry 7 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac7VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.109
VID for Entry 7 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac8VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.110
MAC Address for Entry 8 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac8VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.111
VID for Entry 8 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac9VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.112
MAC Address for Entry 9 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac9VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.113
VID for Entry 9 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mac10VIDMapAddr 1.3.6.1.4.1.161.19.3.3.2.114
MAC Address for Entry 10 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

mac10VIDMapVid 1.3.6.1.4.1.161.19.3.3.2.115
VID for Entry 10 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

vlanPortType 1.3.6.1.4.1.161.19.3.3.2.116
VLAN Port Type for VLAN interface. Default is Q.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q(0), qinq(1)  

vlanAcceptQinQFrames 1.3.6.1.4.1.161.19.3.3.2.117
Allow/Disallow packets already doubly-tagged (QinQ) to ingress the FEC of BHM, BHS, or MP SM. Not configurable on MP AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

whispWebUserAccessMode 1.3.6.1.4.1.161.19.3.3.2.118
This variable selects if web page users for the radio should be authenticated locally or via a centralised remote Radius server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(0), remote(1), remotethenlocal(2)  

usrAccountEnableAccounting 1.3.6.1.4.1.161.19.3.3.2.119
Select the level of accounting information to be reported to the server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), deviceAccess(1), dataUsage(2), all(3)  

allowRejectThenLocal 1.3.6.1.4.1.161.19.3.3.2.120
Control for allowing local authenication if the AAA remote server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER doNotAllowLocalAuthifAAAReject(0), allowLocalAuthIfAAAReject(1)  

snrCalculation 1.3.6.1.4.1.161.19.3.3.2.121
This OID is deprecated. Receive quality calulation is always on since it no longer affects packet per second performance.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

priorityPrecedence 1.3.6.1.4.1.161.19.3.3.2.122
Allows user to decide if 802.1p or DiffServ priority bits should be used first when making priority decisions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER eight021pThenDiffServ(0), diffservThenEight021p(1)  

installationColorCode 1.3.6.1.4.1.161.19.3.3.2.123
Installation Color Code. Allows non-configured SMs to register to an AP with UCC enabled in order to facilitate remote provisioning.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

apSmMode 1.3.6.1.4.1.161.19.3.3.2.124
Set AP to SM or SM to AP. Useful for facillitating scripting of running Spectrum Analyzer on an AP. Radio must have AP Feature Key. 1 - Set to SM, 0 - Set to AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sm(1), ap(0)  

pppoeFilter 1.3.6.1.4.1.161.19.3.3.2.125
To set PPPoE packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

smbFilter 1.3.6.1.4.1.161.19.3.3.2.126
To set SMB packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

snmpFilter 1.3.6.1.4.1.161.19.3.3.2.127
To set SNMP packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP1Filter 1.3.6.1.4.1.161.19.3.3.2.128
To set user defined port 1 packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP2Filter 1.3.6.1.4.1.161.19.3.3.2.129
To set user defined port 2 packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP3Filter 1.3.6.1.4.1.161.19.3.3.2.130
To set user defined port 3 packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allOtherIpFilter 1.3.6.1.4.1.161.19.3.3.2.131
To set all other IPv4 packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allIpv4Filter 1.3.6.1.4.1.161.19.3.3.2.132
To set all IPv4 packet filter. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

arpFilter 1.3.6.1.4.1.161.19.3.3.2.133
To set ARP packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allOthersFilter 1.3.6.1.4.1.161.19.3.3.2.134
To set all other packet filter when.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort1 1.3.6.1.4.1.161.19.3.3.2.135
An integer value of number one user defined port. Range:0-65535
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

port1TCPFilter 1.3.6.1.4.1.161.19.3.3.2.136
To set user defined port 1 TCP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port1UDPFilter 1.3.6.1.4.1.161.19.3.3.2.137
To set user defined port 1 UDP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort2 1.3.6.1.4.1.161.19.3.3.2.138
An integer value of number two user defined port. Range:0-65535
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

port2TCPFilter 1.3.6.1.4.1.161.19.3.3.2.139
To set user defined port 2 TCP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port2UDPFilter 1.3.6.1.4.1.161.19.3.3.2.140
To set user defined port 2 UDP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort3 1.3.6.1.4.1.161.19.3.3.2.141
An integer value of number three user defined port. Range:0-65535
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

port3TCPFilter 1.3.6.1.4.1.161.19.3.3.2.142
To set user defined port 3 TCP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port3UDPFilter 1.3.6.1.4.1.161.19.3.3.2.143
To set user defined port 3 UDP traffic filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

bootpcFilter 1.3.6.1.4.1.161.19.3.3.2.144
To set bootp client sourced packets filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

bootpsFilter 1.3.6.1.4.1.161.19.3.3.2.145
To set bootp server sourced packets filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ip4MultFilter 1.3.6.1.4.1.161.19.3.3.2.146
To set IPv4 MultiCast packets filter when NAT is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

packetFilterDirection 1.3.6.1.4.1.161.19.3.3.2.147
To set packet filter direction. Upstream is default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

encryptionConfig 1.3.6.1.4.1.161.19.3.3.2.148
For supported radio, set the encryption algorithm to use. DES by default. Cannot be set if encryption is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER des(0), aes(1)  

pppoeCtlPriority 1.3.6.1.4.1.161.19.3.3.2.149
Prioritization of PPPoE Control packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

ftpPort 1.3.6.1.4.1.161.19.3.3.2.150
Port used to for FTP. Default is 21.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

httpPort 1.3.6.1.4.1.161.19.3.3.2.151
Port used to for HTTP. Default is 80.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

httpsPort 1.3.6.1.4.1.161.19.3.3.2.152
Port used to for HTTPs. Default is 443.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

snmpPort 1.3.6.1.4.1.161.19.3.3.2.153
Port used to for SNMP. Default is 161.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

snmpTrapPort 1.3.6.1.4.1.161.19.3.3.2.154
Port used to for SNMP Traps. Default is 162.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

webAccess 1.3.6.1.4.1.161.19.3.3.2.155
This variable determines if only HTTP or HTTPs connection are allowed. 0: HTTP Only 1: HTTPs Only 2: HTTP and HTTPs Both
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER http(0), https(1), http-and-https(2)  

syslogDomainNameAppend 1.3.6.1.4.1.161.19.3.3.2.156
Select whether to append the configured management domain name to the Syslog server name. For example, if dnsMgmtDomainName is set to 'example.com', syslogServerAddr is set to 'syslog1', and syslogDomainNameAppend is set to appendDomain, the Syslog Server name used would be 'syslog1.example.com'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

syslogServerAddr 1.3.6.1.4.1.161.19.3.3.2.157
Syslog server address either in dotted decimal notation or a Fully Qualified Domain Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

syslogServerPort 1.3.6.1.4.1.161.19.3.3.2.158
Listening port on the Syslog server. Default is 514.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

syslogMinLevel 1.3.6.1.4.1.161.19.3.3.2.159
Sets the minimum syslog severity to transmit. Messages with a lower severity value (i.e. numerically higher) than this will not be transmitted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fatal(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

allIpv6Filter 1.3.6.1.4.1.161.19.3.3.2.160
To set all IPv6 packet filter. Enabling this will automatically enable all of the known IPv6 filters (SMB, SNMP, Bootp, IPv6 Mcast, User Defined Ports, and All Other IPv6).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ipv6smbFilter 1.3.6.1.4.1.161.19.3.3.2.161
To set IPv6 SMB packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ipv6snmpFilter 1.3.6.1.4.1.161.19.3.3.2.162
To set IPv6 SNMP packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ipv6bootpcFilter 1.3.6.1.4.1.161.19.3.3.2.163
To set IPv6 bootp client sourced packets filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ipv6bootpsFilter 1.3.6.1.4.1.161.19.3.3.2.164
To set IPv6 bootp server sourced packets filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ipv6MultFilter 1.3.6.1.4.1.161.19.3.3.2.165
To set IPv6 MultiCast packets filter when NAT is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allOtherIpv6Filter 1.3.6.1.4.1.161.19.3.3.2.166
To set all other IPv6 packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

snmpStatus 1.3.6.1.4.1.161.19.3.3.2.167
This variable determines SNMP operation mode. 1: Enable SNMPv2c only 2: Enable SNMPv3 only 3: Enable SNMPv2c and SNMPv3
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER snmpv2only(1), snmpv3only(2), snmpv2-and-snmpv3(3)  

telnetStatus 1.3.6.1.4.1.161.19.3.3.2.168
This variable determines if Telnet to enabled or not. 0: Disable Telnet 1: Enable Telnet
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabletelnet(0), enabletelnet(1)  

ftpStatus 1.3.6.1.4.1.161.19.3.3.2.169
This variable determines if FTP to enabled or not. 0: Disable FTP 1: Enable FTP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableftp(0), enableftp(1)  

tftpStatus 1.3.6.1.4.1.161.19.3.3.2.170
This variable determines if TFTP is enabled or not. 0: Disable TFTP 1: Enable TFTP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabletftp(0), enabletftp(1)  

userMode 1.3.6.1.4.1.161.19.3.3.2.171
User Mode 1=Read-Only 0=Read-Write(default).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tcpAckPriority 1.3.6.1.4.1.161.19.3.3.2.172
Prioritize TCP ACK that are 64 bytes or less.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

codePointSelect 1.3.6.1.4.1.161.19.3.3.2.173
Codepoint Select.This represents the CodePoint Selection to be modified via Priority Select
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cp1(1), cp2(2), cp3(3), cp4(4), cp5(5), cp6(6), cp7(7), cp8(8), cp9(9), cp10(10), cp11(11), cp12(12), cp13(13), cp14(14), cp15(15), cp16(16), cp17(17), cp18(18), cp19(19), cp20(20), cp21(21), cp22(22), cp23(23), cp24(24), cp25(25), cp26(26), cp27(27), cp28(28), cp29(29), cp30(30), cp31(31), cp32(32), cp33(33), cp34(34), cp35(35), cp36(36), cp37(37), cp38(38), cp39(39), cp40(40), cp41(41), cp42(42), cp43(43), cp44(44), cp45(45), cp46(46), cp47(47), cp49(49), cp50(50), cp51(51), cp52(52), cp53(53), cp54(54), cp55(55), cp57(57), cp58(58), cp59(59), cp60(60), cp61(61), cp62(62), cp63(63)  

prioritySelect 1.3.6.1.4.1.161.19.3.3.2.174
Priority Select.The priority setting input for the CodePoint selected in CodePoint Select.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7)  

lan1DhcpRelease 1.3.6.1.4.1.161.19.3.3.2.201
Setting the variable to '1' will release LAN1's IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER releaseIP(1)  

lan1DhcpRenew 1.3.6.1.4.1.161.19.3.3.2.202
Setting the variable to '1' will renew LAN1's lease time for its current IP address. Applicable only when NAT is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER renewIP(1)  

lan3DhcpRelease 1.3.6.1.4.1.161.19.3.3.2.203
Setting the variable to '1' will release LAN3's (RF Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER releaseIP(1)  

lan3DhcpRenew 1.3.6.1.4.1.161.19.3.3.2.204
Setting the variable to '1' will renew LAN3's (RF Public) lease time for its current IP address. Applicable only when NAT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER renewIP(1)  

natDhcpRelease 1.3.6.1.4.1.161.19.3.3.2.205
Setting the variable to '1' will release WAN's (NAT Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER releaseIP(1)  

natDhcpRenew 1.3.6.1.4.1.161.19.3.3.2.206
Setting the variable to '1' will renew WAN's (NAT Public) lease time for its current IP address. Applicable only when NAT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER renewIP(1)  

region 1.3.6.1.4.1.161.19.3.3.2.207
Set Region Code for the Unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), otherRegulatory(1), asia(6), europe(3), northAmerica(2), oceania(5), southAmerica(4), africa(7)  

regionAsia 1.3.6.1.4.1.161.19.3.3.2.208
Country Code for Asia.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), india(2), indonesia(3), russiacategory1(4), russiacategory2(5), russiacategory3(6), russiacategory4(7), vietnam(8), malaysia(10)  

regionEurope 1.3.6.1.4.1.161.19.3.3.2.209
Country Code for Europe.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), spain(2), ireland(3), denmark(4), finland(5), germany(6), greece(7), iceland(8), liechtenstein(9), norway(10), portugal(11), switzerland(12), serbia(13), unitedkingdom(14)  

regionNorthAmerica 1.3.6.1.4.1.161.19.3.3.2.210
Country Code for North America.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), canada(3), unitedStates(2), mexico(4), puertoRico(5)  

regionOceania 1.3.6.1.4.1.161.19.3.3.2.211
Country Code for Oceania.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), australia(2), newZealand(3)  

regionSouthAmerica 1.3.6.1.4.1.161.19.3.3.2.212
Country Code for South America.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), brazil(2), ecuador(3), colombia(4), venezuela(5)  

regionOtherRegulatory 1.3.6.1.4.1.161.19.3.3.2.213
Regulatory setting for governing regulatory body.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), other(1), fcc(2), etsi(3), etsilbt(4)  

interleave 1.3.6.1.4.1.161.19.3.3.2.214
Engineering use only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), disabled(1), enabled(2)  

receiveQualityDebug 1.3.6.1.4.1.161.19.3.3.2.215
Enable or disable receive quality calculations for every packet. Enabling(1) will calulate receive quality on all receiving packets. Due to load on CPU, will slightly packet per second capabilities on AP/BH. Default to disabled for all radios. Only applicable to GenII OFDM products and up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

apType 1.3.6.1.4.1.161.19.3.3.2.216
In standard mode, all possible sync sources will be made availble and usedfor autoSync operation. In remote mode, sync over power port will not be available as a sync source. Remote Device mode is where the AP or BHM timing port is connected to an SM or BHS timing port via a sync cable. In this mode, GPS data is unavailable and sync over power port shouldn't be used. If sync over power is desired, and a CMM or other sync over power device is in use, then select standard mode. This should really be named deviceType because this applies to both AP and BHM, but left this as apType for legacy purposes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER standard(0), remote(1)  

regionAfrica 1.3.6.1.4.1.161.19.3.3.2.217
Country Code for Africa.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), algeria(2)  

addCustomFreqMimo 1.3.6.1.4.1.161.19.3.3.2.218
Frequency input ie) 3700.50. Deprecated, please use 'addCustomFreqList'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

removeCustomFreqMimo 1.3.6.1.4.1.161.19.3.3.2.219
Frequency input ie) 3700.50. Deprecated, please use 'removeCustomFreqList'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

timedSpectrumAnalysisDurationBox 1.3.6.1.4.1.161.19.3.3.2.220
Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..1000  

spectrumAnalysisActionBox 1.3.6.1.4.1.161.19.3.3.2.221
Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis Note: AP/BHM will run Spectrum Analysis for the sector. (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours. (7) - Spectrum Analyzer not ready.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stopSpectrumAnalysis(0), startTimedSpectrumAnalysis(1), startContinuousSpectrumAnalysis(2), idleNoSpectrumAnalysis(3), idleCompleteSpectrumAnalysis(4), inProgressTimedSpectrumAnalysis(5), inProgressContinuousSpectrumAnalysis(6), notReady(7)  

mac1VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.222
VID priority for Entry 1 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac1VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.223
VID priority Mode for Entry 1 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac2VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.224
VID priority for Entry 2 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac2VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.225
VID priority Mode for Entry 2 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac3VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.226
VID priority for Entry 3 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac3VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.227
VID priority Mode for Entry 3 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac4VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.228
VID priority for Entry 4 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac4VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.229
VID priority Mode for Entry 4 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac5VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.230
VID priority for Entry 5 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac5VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.231
VID priority Mode for Entry 5 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac6VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.232
VID priority for Entry 6 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac6VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.233
VID priority Mode for Entry 6 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac7VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.234
VID priority for Entry 7 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac7VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.235
VID priority Mode for Entry 7 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac8VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.236
VID priority for Entry 8 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac8VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.237
VID priority Mode for Entry 8 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac9VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.238
VID priority for Entry 9 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac9VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.239
VID priority Mode for Entry 9 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

mac10VIDMapPriority 1.3.6.1.4.1.161.19.3.3.2.240
VID priority for Entry 10 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mac10VIDMapPriorityMode 1.3.6.1.4.1.161.19.3.3.2.241
VID priority Mode for Entry 10 in MAC Address VID Mapping Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

managementVIDPriority 1.3.6.1.4.1.161.19.3.3.2.242
management VID VID VLAN Priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

managementVIDPriorityMode 1.3.6.1.4.1.161.19.3.3.2.243
management VID VLAN Priority Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

remarkSrcVID 1.3.6.1.4.1.161.19.3.3.2.244
Source VID to apply remarking on.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

addRemarkVID 1.3.6.1.4.1.161.19.3.3.2.245
Add VLAN ID re-marking entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

addRemarkPriority 1.3.6.1.4.1.161.19.3.3.2.246
Add 802.1p re-mark entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

deleteRemarkVID 1.3.6.1.4.1.161.19.3.3.2.247
Remove the VID re-marking for this source VID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

deleteRemarkPriority 1.3.6.1.4.1.161.19.3.3.2.248
Remove the priority re-marking for this source VID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

mimoRateAdaptAlgorithm 1.3.6.1.4.1.161.19.3.3.2.249
Engineering use only. Control MIMO Rate Adapt Algorithm 0 = MIMO-A/B This chooses MIMO-A or MIMO-B dynamically to maximize throughput 1 = MIMO-B only 2 = MIMO-A only 3 = SISO only
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mimobmimoa(0), mimobonly(1), mimoaonly(2), siso(3)  

controlMessages 1.3.6.1.4.1.161.19.3.3.2.250
Control Messages (Beacon/Scheduling Map/Acknowledgements/Broadcast) 0 = MIMO-A 1 = SISO MIMO Control Messages is the recommended and default setting. However, SISO Control Messages can be helpful in talking to subscribers on releases previous to 13.2, which operated in this mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER siso(1), mimoa(0)  

enableSecurityBanner 1.3.6.1.4.1.161.19.3.3.2.251
Shows Security Banner at the time of login
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

vcDepth 1.3.6.1.4.1.161.19.3.3.2.252
VC Depth of radio. Engineering use only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), eight(8), sixteen(16), thirty-two(32), sixty-four(64)  

textSecurityBanner 1.3.6.1.4.1.161.19.3.3.2.253
Security Banner to be dispalyed on login page. Length should be maximum 1200 characters.Configuration from web UI can enter upto 1499 characters. Only ASCII characters(0-9a-zA-Z,CR,LF) supported.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

acceptSecurityBanner 1.3.6.1.4.1.161.19.3.3.2.254
1: User must accept and acknowledge security banner before login. 0: Accepting security banner is not mandatory and user can login without it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

simulatedAirDelay 1.3.6.1.4.1.161.19.3.3.2.256
Simulated Air Delay. Engineering use only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

saveFlash 1.3.6.1.4.1.161.19.3.3.3.1
This variable is currently deprecated.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER doNotSaveToFlash(0), saveToFlash(1)  

reboot 1.3.6.1.4.1.161.19.3.3.3.2
Setting the variable to 1 will reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Setting the variable to 2 will perform a full reboot of a 450i radio, while performing a normal reboot on other radios.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER finishedReboot(0), reboot(1), fullReboot(2)  

clearEventLog 1.3.6.1.4.1.161.19.3.3.3.3
Setting the variable to 1 will clear the event log.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notClear(0), clear(1)  

rebootIfRequired 1.3.6.1.4.1.161.19.3.3.3.4
Setting the variable to 1 will reboot the unit if reboot is required.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rebootNotRequired(0), rebootRequired(1)  

clearBERStats 1.3.6.1.4.1.161.19.3.3.3.5
Set to clear the BER statistics by sending a 'clearBERStats'. Value is set back to 'doNotClearBERStats' When action is complete.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER doNotClearBERStats(0), clearBERStats(1)  

updateDevice 1.3.6.1.4.1.161.19.3.3.3.6
Use to update the software on the device
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

importConfigFile 1.3.6.1.4.1.161.19.3.3.3.7
Set to URL to immediately download and apply configuration file
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

exportConfigFile 1.3.6.1.4.1.161.19.3.3.3.8
Set to URL to immediately export and upload configuration file
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

undoUnitWideSavedChanges 1.3.6.1.4.1.161.19.3.3.3.9
Setting to 1 will undo unit wide saved changes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER undoUnitWideSavedChanges(1)  

whispBoxEvntLog 1.3.6.1.4.1.161.19.3.3.5.1
Event log for AP and SM.
Status: current Access: read-only
OBJECT-TYPE    
  EventString  

whispBoxAttributesGroup 1.3.6.1.4.1.161.19.3.3.6.1.1
Canopy Box Level Attributes group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxControlGroup 1.3.6.1.4.1.161.19.3.3.6.1.2
Canopy Box Level control group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxBTGroup 1.3.6.1.4.1.161.19.3.3.6.1.3
Canopy Box Bridging Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxVLANTableGroup 1.3.6.1.4.1.161.19.3.3.6.1.4
Canopy Box VLAN member Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxCPTableGroup 1.3.6.1.4.1.161.19.3.3.6.1.5
Code Point Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxUserTableGroup 1.3.6.1.4.1.161.19.3.3.6.1.6
Canopy Box User Information Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispLayer2NeighborTableGroup 1.3.6.1.4.1.161.19.3.3.6.1.7
Canopy Box Layer 2 Neighbor information.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxNotifGroup 1.3.6.1.4.1.161.19.3.3.6.1.8
Canopy Box Notification Group.
Status: current Access: read-only
NOTIFICATION-GROUP    

whispBoxVLANRemarkTableGroup 1.3.6.1.4.1.161.19.3.3.6.1.9
Canopy Box VLAN Remarking Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxSNMPv3Group 1.3.6.1.4.1.161.19.3.3.6.1.10
Canopy Box SNMPv3 Group.
Status: current Access: read-only
OBJECT-GROUP    

whispBoxLinkTestGroup 1.3.6.1.4.1.161.19.3.3.6.1.11
Canopy Box Link Test group.
Status: current Access: read-only
OBJECT-GROUP    

whispBridgeTbUsed 1.3.6.1.4.1.161.19.3.3.7.1
Number of used entries in bridging table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispBridgeTbFree 1.3.6.1.4.1.161.19.3.3.7.2
Number of free entries in bridging table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispBridgeTbErr 1.3.6.1.4.1.161.19.3.3.7.3
Bridging table errors.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

codePoint0 1.3.6.1.4.1.161.19.3.3.9.1
Code Point 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

codePoint1 1.3.6.1.4.1.161.19.3.3.9.2
Code Point 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint2 1.3.6.1.4.1.161.19.3.3.9.3
Code Point 2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint3 1.3.6.1.4.1.161.19.3.3.9.4
Code Point 3.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint4 1.3.6.1.4.1.161.19.3.3.9.5
Code Point 4.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint5 1.3.6.1.4.1.161.19.3.3.9.6
Code Point 5.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint6 1.3.6.1.4.1.161.19.3.3.9.7
Code Point 6.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint7 1.3.6.1.4.1.161.19.3.3.9.8
Code Point 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint8 1.3.6.1.4.1.161.19.3.3.9.9
Code Point 8.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint9 1.3.6.1.4.1.161.19.3.3.9.10
Code Point 9.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint10 1.3.6.1.4.1.161.19.3.3.9.11
Code Point 10.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint11 1.3.6.1.4.1.161.19.3.3.9.12
Code Point 11.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint12 1.3.6.1.4.1.161.19.3.3.9.13
Code Point 12.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint13 1.3.6.1.4.1.161.19.3.3.9.14
Code Point 13.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint14 1.3.6.1.4.1.161.19.3.3.9.15
Code Point 14.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint15 1.3.6.1.4.1.161.19.3.3.9.16
Code Point 15.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint16 1.3.6.1.4.1.161.19.3.3.9.17
Code Point 16.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint17 1.3.6.1.4.1.161.19.3.3.9.18
Code Point 17.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint18 1.3.6.1.4.1.161.19.3.3.9.19
Code Point 18.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint19 1.3.6.1.4.1.161.19.3.3.9.20
Code Point 19.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint20 1.3.6.1.4.1.161.19.3.3.9.21
Code Point 20.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint21 1.3.6.1.4.1.161.19.3.3.9.22
Code Point 21.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint22 1.3.6.1.4.1.161.19.3.3.9.23
Code Point 22.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint23 1.3.6.1.4.1.161.19.3.3.9.24
Code Point 23.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint24 1.3.6.1.4.1.161.19.3.3.9.25
Code Point 24.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint25 1.3.6.1.4.1.161.19.3.3.9.26
Code Point 25.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint26 1.3.6.1.4.1.161.19.3.3.9.27
Code Point 26.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint27 1.3.6.1.4.1.161.19.3.3.9.28
Code Point 27.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint28 1.3.6.1.4.1.161.19.3.3.9.29
Code Point 28.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint29 1.3.6.1.4.1.161.19.3.3.9.30
Code Point 29.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint30 1.3.6.1.4.1.161.19.3.3.9.31
Code Point 30.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint31 1.3.6.1.4.1.161.19.3.3.9.32
Code Point 31.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint32 1.3.6.1.4.1.161.19.3.3.9.33
Code Point 32.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint33 1.3.6.1.4.1.161.19.3.3.9.34
Code Point 33.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint34 1.3.6.1.4.1.161.19.3.3.9.35
Code Point 34.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint35 1.3.6.1.4.1.161.19.3.3.9.36
Code Point 35.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint36 1.3.6.1.4.1.161.19.3.3.9.37
Code Point 36.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint37 1.3.6.1.4.1.161.19.3.3.9.38
Code Point 37.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint38 1.3.6.1.4.1.161.19.3.3.9.39
Code Point 38.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint39 1.3.6.1.4.1.161.19.3.3.9.40
Code Point 39.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint40 1.3.6.1.4.1.161.19.3.3.9.41
Code Point 40.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint41 1.3.6.1.4.1.161.19.3.3.9.42
Code Point 41.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint42 1.3.6.1.4.1.161.19.3.3.9.43
Code Point 42.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint43 1.3.6.1.4.1.161.19.3.3.9.44
Code Point 43.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint44 1.3.6.1.4.1.161.19.3.3.9.45
Code Point 44.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint45 1.3.6.1.4.1.161.19.3.3.9.46
Code Point 45.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint46 1.3.6.1.4.1.161.19.3.3.9.47
Code Point 46.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint47 1.3.6.1.4.1.161.19.3.3.9.48
Code Point 47.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint48 1.3.6.1.4.1.161.19.3.3.9.49
Code Point 48.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

codePoint49 1.3.6.1.4.1.161.19.3.3.9.50
Code Point 49.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint50 1.3.6.1.4.1.161.19.3.3.9.51
Code Point 50.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint51 1.3.6.1.4.1.161.19.3.3.9.52
Code Point 51.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint52 1.3.6.1.4.1.161.19.3.3.9.53
Code Point 52.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint53 1.3.6.1.4.1.161.19.3.3.9.54
Code Point 53.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint54 1.3.6.1.4.1.161.19.3.3.9.55
Code Point 54.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint55 1.3.6.1.4.1.161.19.3.3.9.56
Code Point 55.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint56 1.3.6.1.4.1.161.19.3.3.9.57
Code Point 56.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

codePoint57 1.3.6.1.4.1.161.19.3.3.9.58
Code Point 57.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint58 1.3.6.1.4.1.161.19.3.3.9.59
Code Point 58.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint59 1.3.6.1.4.1.161.19.3.3.9.60
Code Point 59.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint60 1.3.6.1.4.1.161.19.3.3.9.61
Code Point 60.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint61 1.3.6.1.4.1.161.19.3.3.9.62
Code Point 61.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint62 1.3.6.1.4.1.161.19.3.3.9.63
Code Point 62.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

codePoint63 1.3.6.1.4.1.161.19.3.3.9.64
Code Point 63.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

boxLan1DHCPClientEvent 1.3.6.1.4.1.161.19.3.3.12.1.1
Lan1 DHCP Client has received a new address via DHCP
Status: current Access: read-write
NOTIFICATION-TYPE    

dnsIpState 1.3.6.1.4.1.161.19.3.3.13.1
Configuration for DNS server IP addresses of the management interface are learned: 0 : Manual, must configure dnsPrimaryMgmtIP and dnsAlternateMgmtIP 1 : Automatic, DNS servers IP addresses are learned from DHCP response of the interface
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(0), automatic(1)  

dnsPrimaryMgmtIP 1.3.6.1.4.1.161.19.3.3.13.2
Primary DNS IP address for the management interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsAlternateMgmtIP 1.3.6.1.4.1.161.19.3.3.13.3
Secondary DNS IP address for the management interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsMgmtDomainName 1.3.6.1.4.1.161.19.3.3.13.4
Domain Name to use for management DNS configuration. This domain name may be concatonated to DNS names used configured for the management interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trapDomainNameAppend 1.3.6.1.4.1.161.19.3.3.13.5
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', trap1 is set to 'trap1', and trapDomainNameAppend is set to appendDomain, the trap1 name used would be 'trap1.example.com'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

trap1 1.3.6.1.4.1.161.19.3.3.13.6
SNMP Trap IP Address 1. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap2 1.3.6.1.4.1.161.19.3.3.13.7
SNMP Trap IP Address 2. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap3 1.3.6.1.4.1.161.19.3.3.13.8
SNMP Trap IP Address 3. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap4 1.3.6.1.4.1.161.19.3.3.13.9
SNMP Trap IP Address 4. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap5 1.3.6.1.4.1.161.19.3.3.13.10
SNMP Trap IP Address 5. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap6 1.3.6.1.4.1.161.19.3.3.13.11
SNMP Trap IP Address 6. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap7 1.3.6.1.4.1.161.19.3.3.13.12
SNMP Trap IP Address 7. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap8 1.3.6.1.4.1.161.19.3.3.13.13
SNMP Trap IP Address 8. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap9 1.3.6.1.4.1.161.19.3.3.13.14
SNMP Trap IP Address 9. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trap10 1.3.6.1.4.1.161.19.3.3.13.15
SNMP Trap IP Address 10. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

snmpv2cEnable 1.3.6.1.4.1.161.19.3.3.14.1
Enable(1) or Disable(0) SNMPv2c access
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

snmpv3EngineId 1.3.6.1.4.1.161.19.3.3.14.2
The SNMPv3 engine administratively-unique identifier. Length of the identifier should be 5-32 octets which is 10-64 hexadecimal characters and even.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(10..64)  

snmpv3SecLvl 1.3.6.1.4.1.161.19.3.3.14.3
The security level of the SNMPv3 Engine.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAuth-noPriv(0), auth-noPriv(1), auth-priv(2)  

snmpv3AuthProt 1.3.6.1.4.1.161.19.3.3.14.4
The SNMPv3 message authentication protocol to use. Currently only MD5 is supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER md5(0)  

snmpv3PrivProt 1.3.6.1.4.1.161.19.3.3.14.5
The SNMPv3 message privacy/encryption protocol to use. Currently only CBC-DES is supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cbc-des(0)  

roUserName 1.3.6.1.4.1.161.19.3.3.14.6
SNMPv3 Read-Only username.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

roAuthPassword 1.3.6.1.4.1.161.19.3.3.14.7
SNMPv3 Read-Only message authentication password.Minimum 8 and maximum 32 characters long.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

roPrivPassword 1.3.6.1.4.1.161.19.3.3.14.8
SNMPv3 Read-Only message privacy/encryption password.Minimum 8 and maximum 32 characters long.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

rwUserEnable 1.3.6.1.4.1.161.19.3.3.14.9
SNMPv3 Read-Write User Enable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

rwUserName 1.3.6.1.4.1.161.19.3.3.14.10
SNMPv3 Read-Write Username.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

rwAuthPassword 1.3.6.1.4.1.161.19.3.3.14.11
SNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

rwPrivPassword 1.3.6.1.4.1.161.19.3.3.14.12
SNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

snmpv3TrapEnable 1.3.6.1.4.1.161.19.3.3.14.13
SNMPv3 Trap enable option: (0) Disable - No SNMPv3 Traps Sent (1) Enable Traps to be sent for SNMPv3 Read-Only User (2) Enable Traps to be sent for SNMPv3 Read-Write User NOTE: When disabled SNMPv2c Trap configuration is used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), roUserTrapEnable(1), rwUserTrapEnable(2)  

whispRegStatusBox 1.3.6.1.4.1.161.19.3.3.18.4
This shows the registration status of a link.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

linkTestLUIDBox 1.3.6.1.4.1.161.19.3.3.18.1.1
LUID selection for Link Test. Valid range: 2-255. Read-Only for SM or Backhaul slave, Read/Write for AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestDurationBox 1.3.6.1.4.1.161.19.3.3.18.1.2
Duration for the Link Test. Valid range: 2-10 seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestActionBox 1.3.6.1.4.1.161.19.3.3.18.1.3
Setting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stopped(0), start(1)  

linkTestPktLengthBox 1.3.6.1.4.1.161.19.3.3.18.1.4
Packet length for Link Test. Valid range: 64-1714 bytes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestModeBox 1.3.6.1.4.1.161.19.3.3.18.1.5
Link Test Mode 0 = RF Link Test (traffic doesn't go through bridge, highest throughput) 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rflinktest(0), linktestwithbridging(1), linktestwithbridgingandmir(2), extrapolatedlinktest(3)  

linkTestSNRCalculationBox 1.3.6.1.4.1.161.19.3.3.18.1.6
Enable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

linkTestWithDualPathBox 1.3.6.1.4.1.161.19.3.3.18.1.7
Link Test with: 0 = Low Priority VC only 1 = High and Low Priority VCs
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lowpriorityvconly(0), highandlowpriorityvcs(1)  

linkTestNumPktBox 1.3.6.1.4.1.161.19.3.3.18.1.8
Number of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestForceModulationBox 1.3.6.1.4.1.161.19.3.3.18.1.9
Engineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithm
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normalRateAdapt(0), forceMaxModulation(1)  

linkTestDirectionBox 1.3.6.1.4.1.161.19.3.3.18.1.10
Link Test Direction - Engineering Use Only 0 = default (will do bidirectional) 1 = Uplink Only 2 = Downlink Only 3 = Bi-Directional (same as 0, setting to 3 will result in setting it to 0)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bidirectional(0), uplinkonly(1), downlinkonly(2)  

testLUIDBox 1.3.6.1.4.1.161.19.3.3.18.2.1
LUID number of selected unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkTestStatusBox 1.3.6.1.4.1.161.19.3.3.18.2.2
Status for Link Test.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkTestErrorBox 1.3.6.1.4.1.161.19.3.3.18.2.3
Error status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

testDurationBox 1.3.6.1.4.1.161.19.3.3.18.2.4
Duration of link test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkRateBox 1.3.6.1.4.1.161.19.3.3.18.2.5
Downlink Rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

upLinkRateBox 1.3.6.1.4.1.161.19.3.3.18.2.6
Uplink Rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkEffBox 1.3.6.1.4.1.161.19.3.3.18.2.7
Down Link Efficiency.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxDwnLinkIndexBox 1.3.6.1.4.1.161.19.3.3.18.2.8
For link test results, the maximum possible downlink efficiency percentage (always 100%).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

actDwnLinkIndexBox 1.3.6.1.4.1.161.19.3.3.18.2.9
Actual down link index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

expDwnFragCountBox 1.3.6.1.4.1.161.19.3.3.18.2.10
Expected Fragment Count.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

actDwnFragCountBox 1.3.6.1.4.1.161.19.3.3.18.2.11
Actual Fragment Count
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

upLinkEffBox 1.3.6.1.4.1.161.19.3.3.18.2.12
Up link efficiency.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

expUpFragCountBox 1.3.6.1.4.1.161.19.3.3.18.2.13
Uplink expected Fragment Count.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

actUpFragCountBox 1.3.6.1.4.1.161.19.3.3.18.2.14
Actual uplink Fragment Count.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

maxUpLinkIndexBox 1.3.6.1.4.1.161.19.3.3.18.2.15
For link test results, the maximum possible uplink efficiency percentage (always 100%).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

actUpLinkIndexBox 1.3.6.1.4.1.161.19.3.3.18.2.16
Actual Up link index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.17
Number of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.18
Number of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.19
Number of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.20
Number of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.21
Number of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.22
Number of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.23
Number of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.24
Number of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

bitErrorsCorrected1xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.25
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.26
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.27
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xDwnLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.28
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected1xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.29
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.30
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.31
Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.32
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioDownLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.33
Estimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

signalToNoiseRatioUpLinkVerticalBox 1.3.6.1.4.1.161.19.3.3.18.2.34
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.35
Number of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.36
Number of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.37
Number of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.38
Number of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.39
Number of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.40
Number of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.41
Number of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.42
Number of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

bitErrorsCorrected1xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.43
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.44
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.45
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xDwnLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.46
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected1xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.47
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.48
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.49
Engineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.50
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioDownLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.51
Estimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

signalToNoiseRatioUpLinkHorizontalBox 1.3.6.1.4.1.161.19.3.3.18.2.52
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkRateExtrapolatedBox 1.3.6.1.4.1.161.19.3.3.18.2.53
Extrapolated Downlink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

upLinkRateExtrapolatedBox 1.3.6.1.4.1.161.19.3.3.18.2.54
Extrapolated Uplink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkTestLastRunTime 1.3.6.1.4.1.161.19.3.3.18.2.55
Time and Date when last link test ran.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispBoxRFPhysicalRadios 1.3.6.1.4.1.161.19.3.3.15.1
Radio information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispBoxRFPhysicalRadioEntry

whispBoxRFPhysicalRadioEntry 1.3.6.1.4.1.161.19.3.3.15.1.1
Radio information table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispBoxRFPhysicalRadioEntry  

radioIndex 1.3.6.1.4.1.161.19.3.3.15.1.1.1
Radio Index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

radioType 1.3.6.1.4.1.161.19.3.3.15.1.1.2
Indicates if the radio is FSK or OFDM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fsk(0), ofdm(1)  

radioPaths 1.3.6.1.4.1.161.19.3.3.15.1.1.3
Indicates number of paths. For FSK or OFDM (non-MIMO), this is 1. For MIMO, it can be greater (with a current maximum of 2).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

whispBoxRFPhysicalRadioPaths 1.3.6.1.4.1.161.19.3.3.15.2
Radio path information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispBoxRFPhysicalRadioPathEntry

whispBoxRFPhysicalRadioPathEntry 1.3.6.1.4.1.161.19.3.3.15.2.1
Radio path table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispBoxRFPhysicalRadioPathEntry  

pathIndex 1.3.6.1.4.1.161.19.3.3.15.2.1.1
Path Index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

whispBoxRFPhysicalRadioFrequencies 1.3.6.1.4.1.161.19.3.3.15.3
Available frequency information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispBoxRFPhysicalRadioFrequencyEntry

whispBoxRFPhysicalRadioFrequencyEntry 1.3.6.1.4.1.161.19.3.3.15.3.1
Available frequency table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispBoxRFPhysicalRadioFrequencyEntry  

frequency 1.3.6.1.4.1.161.19.3.3.15.3.1.1
Frequency.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..9000000  

whispBoxRFConfigRadios 1.3.6.1.4.1.161.19.3.3.16.1
Radio configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispBoxRFConfigRadioEntry

whispBoxRFConfigRadioEntry 1.3.6.1.4.1.161.19.3.3.16.1.1
Radio config table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispBoxRFConfigRadioEntry  

radioConfigIndex 1.3.6.1.4.1.161.19.3.3.16.1.1.1
Radio Config Index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

radioFrequencyBand 1.3.6.1.4.1.161.19.3.3.16.1.1.2
Currently configured radio band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER band700(0), band900(1), band2400(2), band3500(3), band3700(4), band4900(5), band5100(6), band5200(7), band5400(8), band5700(9), band5800(10), band5900(11), band6050(12)  

whispBoxBridgeTable 1.3.6.1.4.1.161.19.3.3.4
Bridge table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispBoxBridgeEntry

whispBoxBridgeEntry 1.3.6.1.4.1.161.19.3.3.4.1
Bridge entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispBoxBridgeEntry  

whispBridgeMacAddr 1.3.6.1.4.1.161.19.3.3.4.1.1
MAC Address of the registered enity.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

whispBridgeDesLuid 1.3.6.1.4.1.161.19.3.3.4.1.2
This is the Local Unit Identifier assigned to Subscriber Modems.
Status: current Access: read-only
OBJECT-TYPE    
  WhispLUID  

whispBridgeAge 1.3.6.1.4.1.161.19.3.3.4.1.3
Table entry last access age in minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispBridgeExt 1.3.6.1.4.1.161.19.3.3.4.1.4
Timeout extension flag for entries which also reside in the PNA APR cache.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispBridgeHash 1.3.6.1.4.1.161.19.3.3.4.1.5
Hash table array index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispBridgeCAM 1.3.6.1.4.1.161.19.3.3.4.1.6
This entry is deprecated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

whispVLANTable 1.3.6.1.4.1.161.19.3.3.8
VLAN member table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispVLANEntry

whispVLANEntry 1.3.6.1.4.1.161.19.3.3.8.1
VLAN entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispVLANEntry  

whispVID 1.3.6.1.4.1.161.19.3.3.8.1.1
VLAN member ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

whispVType 1.3.6.1.4.1.161.19.3.3.8.1.2
VLAN member type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispVAge 1.3.6.1.4.1.161.19.3.3.8.1.3
VLAN member age.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispVLANRemarkTable 1.3.6.1.4.1.161.19.3.3.17
Active VLAN Remarking table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispVLANRemarkEntry

whispVLANRemarkEntry 1.3.6.1.4.1.161.19.3.3.17.1
Remarking VLAN entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispVLANRemarkEntry  

sourceVID 1.3.6.1.4.1.161.19.3.3.17.1.1
Source VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

remarkVIDState 1.3.6.1.4.1.161.19.3.3.17.1.2
Remark VID State.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remarkVID 1.3.6.1.4.1.161.19.3.3.17.1.3
Remark VID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4094  

remarkPriorityState 1.3.6.1.4.1.161.19.3.3.17.1.4
Remark Priority State.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

remarkPriority 1.3.6.1.4.1.161.19.3.3.17.1.5
Remark Priority.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

whispUserTable 1.3.6.1.4.1.161.19.3.3.10
User information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispUserEntry

whispUserEntry 1.3.6.1.4.1.161.19.3.3.10.1
User entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispUserEntry  

entryIndex 1.3.6.1.4.1.161.19.3.3.10.1.1
User information table index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

userLoginName 1.3.6.1.4.1.161.19.3.3.10.1.2
User name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

userPswd 1.3.6.1.4.1.161.19.3.3.10.1.3
User password.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

accessLevel 1.3.6.1.4.1.161.19.3.3.10.1.4
User access level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loginStatus 1.3.6.1.4.1.161.19.3.3.10.1.5
User current status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loginMethod 1.3.6.1.4.1.161.19.3.3.10.1.6
User login method.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sessionTime 1.3.6.1.4.1.161.19.3.3.10.1.7
Users logged in session time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispLayer2NeighborTable 1.3.6.1.4.1.161.19.3.3.11
Neighbor information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispLayer2NeighborEntry

whispLayer2NeighborEntry 1.3.6.1.4.1.161.19.3.3.11.1
Neighbor Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispLayer2NeighborEntry  

entryL2Index 1.3.6.1.4.1.161.19.3.3.11.1.1
Neighbor information table index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..20  

neighborMAC 1.3.6.1.4.1.161.19.3.3.11.1.2
Neighbor MAC.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

neighborIP 1.3.6.1.4.1.161.19.3.3.11.1.3
Neighbor IP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

neighborSiteName 1.3.6.1.4.1.161.19.3.3.11.1.4
Neighbor Site Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString