WHISP-SM-MIB

File: WHISP-SM-MIB.mib (111345 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
WHISP-TCV2-MIB WHISP-GLOBAL-REG-MIB WHISP-BOX-MIBV2-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Counter64 Gauge32 TimeTicks
IpAddress Unsigned32 DisplayString
PhysAddress MacAddress OBJECT-GROUP
WhispLUID WhispMACAddress whispModules
whispBox whispAps whispSm
dhcpRfPublicIp whispBoxEsn

Defined Types

RfScanListEntry  
SEQUENCE    
  rfScanListFrequency INTEGER

CertEntry  
SEQUENCE    
  certIndex INTEGER
  cert INTEGER
  action INTEGER
  certificateDN DisplayString

DhcpServerEntry  
SEQUENCE    
  hostIp IpAddress
  hostMacAddress PhysAddress
  hostLease TimeTicks

WhispMappingEntry  
SEQUENCE    
  tableIndex INTEGER
  protocol INTEGER
  port INTEGER
  localIp IpAddress

WhispSmTranslationTableEntry  
SEQUENCE    
  whispTranslationTableIndex INTEGER
  whispTranslationTableMacAddr MacAddress
  whispTranslationTableIpAddr IpAddress
  whispTranslationTableAge Counter32

WhispSmColorCodeEntry  
SEQUENCE    
  entryColorCode INTEGER
  entryColorCodePriority INTEGER

WhispSmAPEvalEntry  
SEQUENCE    
  evalIndex INTEGER
  evalFrequency INTEGER
  evalChannelBandwidth INTEGER
  evalCyclicPrefix INTEGER
  evalESN PhysAddress
  evalRegion DisplayString
  evalBeaconReceivePowerCombined INTEGER
  evalBeaconReceivePowerH INTEGER
  evalBeaconReceivePowerV INTEGER
  evalFECEnable INTEGER
  evalType INTEGER
  evalAvail INTEGER
  evalAge INTEGER
  evalLockout INTEGER
  evalRegFail INTEGER
  evalRange INTEGER
  evalMaxRange INTEGER
  evalTxBER INTEGER
  evalEBCast INTEGER
  evalSessionCount INTEGER
  evalNoLuid INTEGER
  evalOutOfRange INTEGER
  evalAuthFail INTEGER
  evalEncryptFail INTEGER
  evalReScanReq INTEGER
  evalLimitReached INTEGER
  evalNoVCs INTEGER
  evalVCReserveFail INTEGER
  evalVCActFail INTEGER
  evalTxPower INTEGER
  evalReceiveTargetLevel INTEGER
  evalColorCode INTEGER
  evalBeaconVersion INTEGER
  evalSectorUserCount INTEGER
  evalSyncSrc INTEGER
  evalNumULSlots INTEGER
  evalNumDLSlots INTEGER
  evalNumULContSlots INTEGER
  evalICC INTEGER
  evalAuthentication INTEGER
  evalSMPPPoE INTEGER
  evalPToPVLAN INTEGER
  evalFramePeriod INTEGER

Defined Values

whispSmMibModule 1.3.6.1.4.1.161.19.1.1.13
This module contains MIB definitions for Subscriber Modem.
MODULE-IDENTITY    

whispSmConfig 1.3.6.1.4.1.161.19.3.2.1
OBJECT IDENTIFIER    

whispSmSecurity 1.3.6.1.4.1.161.19.3.2.7
OBJECT IDENTIFIER    

whispSmStatus 1.3.6.1.4.1.161.19.3.2.2
OBJECT IDENTIFIER    

whispSmGroups 1.3.6.1.4.1.161.19.3.2.3
OBJECT IDENTIFIER    

whispSmEvent 1.3.6.1.4.1.161.19.3.2.4
OBJECT IDENTIFIER    

whispSmDfsEvent 1.3.6.1.4.1.161.19.3.2.4.1
OBJECT IDENTIFIER    

whispSmSpAnEvent 1.3.6.1.4.1.161.19.3.2.4.2
OBJECT IDENTIFIER    

whispSmDHCPClientEvent 1.3.6.1.4.1.161.19.3.2.4.3
OBJECT IDENTIFIER    

whispSmControls 1.3.6.1.4.1.161.19.3.2.8
OBJECT IDENTIFIER    

rfScanList 1.3.6.1.4.1.161.19.3.2.1.1
RF scan list string. The frequencies vary by product and region. If the list is too long an SNMP error will be returned. If this occurs please refer to OID rfScanListTable, which will allow user to enter the full range of available frequencies. Special settings: 0: none. all: All frequencies in the band(s) supported by the radio will be selected. all49, all51, all52: Available only for 450i 5 GHz wideband radio. all54, all57: Available only for 450 and 450i 5 GHz radios. When doing a set, separate values with comma with no white space between values.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

powerUpMode 1.3.6.1.4.1.161.19.3.2.1.2
SM Power Up Mode With No 802.3 Link. 1 -- Power up in Aim mode 2 -- Power up in Operational mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER operational(0), aim(1)  

lanIpSm 1.3.6.1.4.1.161.19.3.2.1.3
LAN IP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanMaskSm 1.3.6.1.4.1.161.19.3.2.1.4
LAN subnet mask.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

defaultGwSm 1.3.6.1.4.1.161.19.3.2.1.5
Default gateway.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

networkAccess 1.3.6.1.4.1.161.19.3.2.1.6
Network accessibility. Public or local IP. For multipoint only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER localIP(0), publicIP(1)  

authKeySm 1.3.6.1.4.1.161.19.3.2.1.7
Authentication key. It should be equal or less than 32 characters long.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  


authKeyOption 1.3.6.1.4.1.161.19.3.2.1.9
This option is for SMs only. Backhaul timing slave always uses the set key. 0 - Use default key. 1 - Use set key.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER useDefault(0), useKeySet(1)  

timingPulseGated 1.3.6.1.4.1.161.19.3.2.1.10
0 - Disable (Always propagate the frame timing pulse). 1 - Enable (If SM out of sync then dont propagate the frame timing pulse).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

naptPrivateIP 1.3.6.1.4.1.161.19.3.2.1.11
NAPT private IP address. Only the first three bytes can be changed when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptPrivateSubnetMask 1.3.6.1.4.1.161.19.3.2.1.12
NAPT private subnet mask. Only the last byte can be changed when NAPT is enabled. The address will always be: 255.255.255.x.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptPublicIP 1.3.6.1.4.1.161.19.3.2.1.13
IP Address of NAPT Public Interface. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptPublicSubnetMask 1.3.6.1.4.1.161.19.3.2.1.14
Subnet mask for NAPT Public Interface. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptPublicGatewayIP 1.3.6.1.4.1.161.19.3.2.1.15
IP Address of NAPT Public Interface Gateway. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptRFPublicIP 1.3.6.1.4.1.161.19.3.2.1.16
IP Address of RF Public Interface. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptRFPublicSubnetMask 1.3.6.1.4.1.161.19.3.2.1.17
Subnet mask of RF Public Interface. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptRFPublicGateway 1.3.6.1.4.1.161.19.3.2.1.18
IP Address of RF Public Interface Gateway. The variable is available only when NAPT is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

naptEnable 1.3.6.1.4.1.161.19.3.2.1.19
To enable or disable NAPT. For multipoint only. 1=Enable NAPT, 0=Disable NAPT.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

arpCacheTimeout 1.3.6.1.4.1.161.19.3.2.1.20
ARP cache time out in unit of minutes. For multipoint only. Range from 1-30.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tcpGarbageCollectTmout 1.3.6.1.4.1.161.19.3.2.1.21
Units of minutes for TCP garbage collection. For multipoint only. Range 4-1440.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

udpGarbageCollectTmout 1.3.6.1.4.1.161.19.3.2.1.22
Units of minutes for UDP garbage collection. For multipoint only. Range 1-1440.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpClientEnable 1.3.6.1.4.1.161.19.3.2.1.23
To enable or disable DHCP client. For multipoint SM's with NAPT enabled.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpServerEnable 1.3.6.1.4.1.161.19.3.2.1.24
To enable or disable DHCP server. For multipoint SM's with NAPT enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpServerLeaseTime 1.3.6.1.4.1.161.19.3.2.1.25
Units of days for DHCP server lease time. For multipoint SM's with NAPT enabled. Range from 1-30.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpIPStart 1.3.6.1.4.1.161.19.3.2.1.26
The last byte will be set for the starting IP that our DHCP server gives away. The first 3 bytes of the starting IP are the same as those of NAPT private IP
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsAutomatic 1.3.6.1.4.1.161.19.3.2.1.27
To have DHCP Server obtain DNS information automatically or manually.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manually(0), automatically(1)  

prefferedDNSIP 1.3.6.1.4.1.161.19.3.2.1.28
The preferred DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

alternateDNSIP 1.3.6.1.4.1.161.19.3.2.1.29
The alternate DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dmzIP 1.3.6.1.4.1.161.19.3.2.1.30
Only the last byte of DMZ Host IP will be set. The first 3 bytes of DMZ IP are the same as those of NAPT private IP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dmzEnable 1.3.6.1.4.1.161.19.3.2.1.31
To enable or disable DMZ host functionality.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpNumIPsToLease 1.3.6.1.4.1.161.19.3.2.1.32
Number of IP addresses that our DHCP server can give away.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pppoeFilter 1.3.6.1.4.1.161.19.3.2.1.33
To set PPPoE packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

smbFilter 1.3.6.1.4.1.161.19.3.2.1.34
To set SMB packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

snmpFilter 1.3.6.1.4.1.161.19.3.2.1.35
To set SNMP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP1Filter 1.3.6.1.4.1.161.19.3.2.1.36
To set user defined port 1 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP2Filter 1.3.6.1.4.1.161.19.3.2.1.37
To set user defined port 2 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userP3Filter 1.3.6.1.4.1.161.19.3.2.1.38
To set user defined port 3 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allOtherIpFilter 1.3.6.1.4.1.161.19.3.2.1.39
To set all other IPv4 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

upLinkBCastFilter 1.3.6.1.4.1.161.19.3.2.1.40
This variable is currently obsolete.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

arpFilter 1.3.6.1.4.1.161.19.3.2.1.41
To set ARP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

allOthersFilter 1.3.6.1.4.1.161.19.3.2.1.42
To set all other packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort1 1.3.6.1.4.1.161.19.3.2.1.43
An integer value of number one user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

port1TCPFilter 1.3.6.1.4.1.161.19.3.2.1.44
To set user defined port 1 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port1UDPFilter 1.3.6.1.4.1.161.19.3.2.1.45
To set user defined port 1 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort2 1.3.6.1.4.1.161.19.3.2.1.46
An integer value of number two user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

port2TCPFilter 1.3.6.1.4.1.161.19.3.2.1.47
To set user defined port 2 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port2UDPFilter 1.3.6.1.4.1.161.19.3.2.1.48
To set user defined port 2 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

userDefinedPort3 1.3.6.1.4.1.161.19.3.2.1.49
An integer value of number three user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

port3TCPFilter 1.3.6.1.4.1.161.19.3.2.1.50
To set user defined port 3 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

port3UDPFilter 1.3.6.1.4.1.161.19.3.2.1.51
To set user defined port 3 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

bootpcFilter 1.3.6.1.4.1.161.19.3.2.1.52
To set bootp client sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

bootpsFilter 1.3.6.1.4.1.161.19.3.2.1.53
To set bootp server sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ip4MultFilter 1.3.6.1.4.1.161.19.3.2.1.54
To set IPv4 MultiCast packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

ingressVID 1.3.6.1.4.1.161.19.3.2.1.55
Untagged ingress VID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

lowPriorityUplinkCIR 1.3.6.1.4.1.161.19.3.2.1.56
Low priority uplink CIR.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

lowPriorityDownlinkCIR 1.3.6.1.4.1.161.19.3.2.1.57
Low priority downlink CIR.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hiPriorityChannel 1.3.6.1.4.1.161.19.3.2.1.58
To enable or disable high priority channel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enable(1)  

hiPriorityUplinkCIR 1.3.6.1.4.1.161.19.3.2.1.59
High priority uplink CIR.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hiPriorityDownlinkCIR 1.3.6.1.4.1.161.19.3.2.1.60
High priority downlink CIR.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

smRateAdapt 1.3.6.1.4.1.161.19.3.2.1.61
Rate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x,2x and 3x adaptation.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER onex(0), onextwox(1), onextwoxthreex(2)  

upLnkDataRate 1.3.6.1.4.1.161.19.3.2.1.62
Sustained uplink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

upLnkLimit 1.3.6.1.4.1.161.19.3.2.1.63
Burst uplink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkDataRate 1.3.6.1.4.1.161.19.3.2.1.64
Sustained downlink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkLimit 1.3.6.1.4.1.161.19.3.2.1.65
Burst downlink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dfsConfig 1.3.6.1.4.1.161.19.3.2.1.66
To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ethAccessFilterEnable 1.3.6.1.4.1.161.19.3.2.1.67
To enable or disable Ethernet Port access filtering to SM Management Functions. (0) - Ethernet access to SM Management allowed. (1) - Ethernet access to SM Management blocked.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

ipAccessFilterEnable 1.3.6.1.4.1.161.19.3.2.1.68
To enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

allowedIPAccess1 1.3.6.1.4.1.161.19.3.2.1.69
Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

allowedIPAccess2 1.3.6.1.4.1.161.19.3.2.1.70
Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

allowedIPAccess3 1.3.6.1.4.1.161.19.3.2.1.71
Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

rfDhcpState 1.3.6.1.4.1.161.19.3.2.1.72
To enable or disable RF Interface DHCP feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bCastMIR 1.3.6.1.4.1.161.19.3.2.1.73
To enable and set Broadcast/ Multicast MIR feature. Use value of 0 to disable. Units are as per bCastMIRUnits variable. Set the units first and then set this value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0)  

bhsReReg 1.3.6.1.4.1.161.19.3.2.1.74
Allows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

smLEDModeFlag 1.3.6.1.4.1.161.19.3.2.1.75
To set LED Panel Operation to Revised Mode(1) or to Legacy Mode(0)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER legacy(0), revised(1)  

ethAccessEnable 1.3.6.1.4.1.161.19.3.2.1.76
To enable or disable Ethernet Port access to SM Management Functions. (1) - Ethernet access to SM Management allowed. (0) - Ethernet access to SM Management blocked.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pppoeEnable 1.3.6.1.4.1.161.19.3.2.1.77
Enable or disable PPPoE on the SM. NAT MUST be enabled prior and Translation Bridging MUST be DISABLED on the AP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pppoeAuthenticationType 1.3.6.1.4.1.161.19.3.2.1.78
Set the PPPoE Authentication Type to either None or CHAP/pap
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), chap-pap(1)  

pppoeAccessConcentrator 1.3.6.1.4.1.161.19.3.2.1.79
Set the PPPoE Access Concentrator Name. Less than or equal to 32 characters
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

pppoeServiceName 1.3.6.1.4.1.161.19.3.2.1.80
Set the PPPoE Service Name. Less than or equal to 32 characters
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

pppoeUserName 1.3.6.1.4.1.161.19.3.2.1.81
Set the PPPoE Username. Less than or equal to 32 characters
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

pppoePassword 1.3.6.1.4.1.161.19.3.2.1.82
Set the PPPoE Password. Less than or equal to 32 characters
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

pppoeTCPMSSClampEnable 1.3.6.1.4.1.161.19.3.2.1.83
Enable or disable TCP MSS Clamping. Enabling this will cause the SM to edit the TCP MSS in TCP SYN and SYN-ACK packets. This will allow for a workaround for MTU issues so that the TCP session will only go up to the clamped MSS. If you are using PMTUD reliably, this should not be needed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pppoeMTUOverrideEnable 1.3.6.1.4.1.161.19.3.2.1.84
Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pppoeMTUOverrideValue 1.3.6.1.4.1.161.19.3.2.1.85
Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used. Max MTU of a PPPoE link is 1492.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1492  

pppoeTimerType 1.3.6.1.4.1.161.19.3.2.1.86
Set the PPPoE Timer type. Can be a Keep Alive timer where the link will be checked periodically and automatically redialed if the link is down. Also could be an Idle Timeout where the link will be automatically dropped after an idle period and redialed if user data is present. Keep Alive timers are in seconds while Idle Timeout timers are in minutes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER keepAlive(1), idleTimeout(2)  

pppoeTimeoutPeriod 1.3.6.1.4.1.161.19.3.2.1.87
The Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes. Minimum values are 20 seconds for KeepAlive timer, and 5 minutes for Idle Timeout.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

timedSpectrumAnalysisDuration 1.3.6.1.4.1.161.19.3.2.1.88
As of release 13.0.2 this value is depricated. Please use the OID in whispBoxConfig. Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 10..1000  

spectrumAnalysisOnBoot 1.3.6.1.4.1.161.19.3.2.1.89
To enable or disable Spectrum Analysis on boot up for one scan through the band. (0) - Disabled (1) - Enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

spectrumAnalysisAction 1.3.6.1.4.1.161.19.3.2.1.90
As of release 13.0.2, this OID has been deprecated. Please use the OID in whispBoxConfig. Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER stopSpectrumAnalysis(0), startTimedSpectrumAnalysis(1), startContinuousSpectrumAnalysis(2), idleNoSpectrumAnalysis(3), idleCompleteSpectrumAnalysis(4), inProgressTimedSpectrumAnalysis(5), inProgressContinuousSpectrumAnalysis(6)  

pppoeConnectOD 1.3.6.1.4.1.161.19.3.2.1.91
Force a manual PPPoE connection attempt.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER connectOnDemand(1)  

pppoeDisconnectOD 1.3.6.1.4.1.161.19.3.2.1.92
Force a manual PPPoE disconnection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disconnectOnDemand(1)  

smAntennaType 1.3.6.1.4.1.161.19.3.2.1.93
Deprecated. See whispBoxStatus.antType for antenna type information.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER integrated(0), external(1)  

natConnectionType 1.3.6.1.4.1.161.19.3.2.1.94
To configure the SM NAT connection type. Options are Static IP, DHCP, or PPPoE.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER staticIP(0), dhcp(1), pppoe(2)  

wanPingReplyEnable 1.3.6.1.4.1.161.19.3.2.1.95
Allow Ping replies from SM WAN interface. Applies to both NAT and PPPoE WAN interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

packetFilterDirection 1.3.6.1.4.1.161.19.3.2.1.96
To packet filter direction when NAT is disabled. Upstream is default. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

colorCode2 1.3.6.1.4.1.161.19.3.2.1.97
Second Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority2 1.3.6.1.4.1.161.19.3.2.1.98
Priority setting for the second color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode3 1.3.6.1.4.1.161.19.3.2.1.99
Third Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority3 1.3.6.1.4.1.161.19.3.2.1.100
Priority setting for the third color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode4 1.3.6.1.4.1.161.19.3.2.1.101
Fourth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority4 1.3.6.1.4.1.161.19.3.2.1.102
Priority setting for the fourth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode5 1.3.6.1.4.1.161.19.3.2.1.103
Fifth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority5 1.3.6.1.4.1.161.19.3.2.1.104
Priority setting for the fifth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode6 1.3.6.1.4.1.161.19.3.2.1.105
Sixth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority6 1.3.6.1.4.1.161.19.3.2.1.106
Priority setting for the sixth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode7 1.3.6.1.4.1.161.19.3.2.1.107
Seventh Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority7 1.3.6.1.4.1.161.19.3.2.1.108
Priority setting for the seventh color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode8 1.3.6.1.4.1.161.19.3.2.1.109
Eighth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority8 1.3.6.1.4.1.161.19.3.2.1.110
Priority setting for the eighth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode9 1.3.6.1.4.1.161.19.3.2.1.111
Ninth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority9 1.3.6.1.4.1.161.19.3.2.1.112
Priority setting for the ninth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

colorCode10 1.3.6.1.4.1.161.19.3.2.1.113
Tenth Color code. The variable is deprecated. See additionalColorCode in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

colorCodepriority10 1.3.6.1.4.1.161.19.3.2.1.114
Priority setting for the tenth color code. The variable is deprecated. See additionalColorCodePriority in whispSmConfig.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3), disable(0)  

natDNSProxyEnable 1.3.6.1.4.1.161.19.3.2.1.115
If enabled, the SM will advertise itself as the DNS server when it sends out DHCP client leases and forward DNS queries automatically. If disabled, the SM will forward on upstream DNS server information when it sends out DHCP client leases.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

allIpv4Filter 1.3.6.1.4.1.161.19.3.2.1.116
To set all IPv4 packet filter when NAT is disabled. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4). Obsolete - Use corresponding OID in whipsBoxConfig MIB.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER filterOff(0), filterOn(1)  

spectrumAnalysisDisplay 1.3.6.1.4.1.161.19.3.2.1.117
The display for Spectrum Analyzer: (0) - Averaging over entire period (1) - Instantaneous showing the last reading
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER averaging(0), instantaneous(1)  

syslogSMXmitSetting 1.3.6.1.4.1.161.19.3.2.1.118
Obtains Syslog transmit configuration from AP/BHM if set to 0, overrides if 1 or 2. Transmits syslog data to Syslog server if enabled(1), stops if disabled (2).
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER obtain-from-AP(0), enable(1), disable(2)  

syslogServerApPreferred 1.3.6.1.4.1.161.19.3.2.1.119
Uses Syslog server configuration from AP/BHM if enabled and available, otherwise uses local configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER use-local(0), use-AP-preferred(1)  

syslogMinLevelApPreferred 1.3.6.1.4.1.161.19.3.2.1.120
Uses Syslog minimum transmit level configuration from AP/BHM if available, otherwise uses local configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER use-local(0), use-AP-preferred(1)  

syslogSMXmitControl 1.3.6.1.4.1.161.19.3.2.1.121
Obtains Syslog transmit configuration from AP/BHM if available, or specifies the local transmit state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER obtain-from-AP-default-disabled(0), obtain-from-AP-default-enabled(1), disable(2), enable(3)  

eapPeerAAAServerCommonName 1.3.6.1.4.1.161.19.3.2.1.126
THIS OID IS CURRENTLY UNUSED: EAP Peer Server Common Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

rfScanListBandFilter 1.3.6.1.4.1.161.19.3.2.1.127
This element is obsolete.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER band5400(8), band5700(9)  

upLnkMaxBurstDataRate 1.3.6.1.4.1.161.19.3.2.1.128
Maximum burst uplink rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkMaxBurstDataRate 1.3.6.1.4.1.161.19.3.2.1.129
Maximum burst downlink rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

cyclicPrefixScan 1.3.6.1.4.1.161.19.3.2.1.130
Cyclic Prefix value for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of cyclic prefixes with no spaces. For example: 1/8,1/16
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

bandwidthScan 1.3.6.1.4.1.161.19.3.2.1.131
Bandwidth values for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of bandwidths. For example: 10, 20
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

apSelection 1.3.6.1.4.1.161.19.3.2.1.132
This OID affects what AP to attempt to register to when Canopy SMs scan see more than one AP that are valid in it's configuration. (0) - Default, Canopy radios after scanning select the best AP that will optimize for estimated throughput. (1) - Select the AP with the best receive power level. Note this is only if multiple APs fit the current scan configuration, and will be overriden by color codes, RADIUS, etc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER powerLevel(1), optimizeForThroughput(0)  

radioBandscanConfig 1.3.6.1.4.1.161.19.3.2.1.133
Used to determine when frequency, cyclic prefix and bandwidth settings take effect for band scanning MIMO SMs. 0 - Instant 1 - Delayed 2 - Apply changes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER instant(0), delayed(1), apply(2)  

forcepoweradjust 1.3.6.1.4.1.161.19.3.2.1.134
This will force a multipoint SM to initiate an asynchronous power adjust sequence. This is done automatically every 2 minutes.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

clearBerrResults 1.3.6.1.4.1.161.19.3.2.1.135
This will clear the BER results.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

berrautoupdateflag 1.3.6.1.4.1.161.19.3.2.1.136
This indicates if the once a second BERR updating of counters is enabled. 1 = enabled 0 = disabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

testSMBER 1.3.6.1.4.1.161.19.3.2.1.137
0 - Disable (Return the SM to a normal operation state). 1 - Enable (Set SM into a BER test state).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

allowedIPAccessNMLength1 1.3.6.1.4.1.161.19.3.2.1.138
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

allowedIPAccessNMLength2 1.3.6.1.4.1.161.19.3.2.1.139
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

allowedIPAccessNMLength3 1.3.6.1.4.1.161.19.3.2.1.140
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

naptRemoteManage 1.3.6.1.4.1.161.19.3.2.1.141
To enable or disable Remote Management. For multipoint only. 0=Disable Remote Management, 1=Enable - Standalone Config, 2=Enable - Use WAN Interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable-standalone(1), enable-wan(2)  

spectrumAnalysisScanBandwidth 1.3.6.1.4.1.161.19.3.2.1.142
Scanning Bandwidth used for the Spectrum Analyzer. Only available on PMP 450.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bandwidth5MHz(0), bandwidth10MHz(1), bandwidth20MHz(2)  

berDeModSelect 1.3.6.1.4.1.161.19.3.2.1.143
The BER demodulation level the SM is set. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER qpsk(0), qam-16(1), qam-64(2), qam-256(3)  

multicastVCRcvRate 1.3.6.1.4.1.161.19.3.2.1.144
Multicast VC Receive Rate
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pmp430ApRegistrationOptions 1.3.6.1.4.1.161.19.3.2.1.145
Selects AP types (PMP 430 and/or PMP 450/450i) that are available for the PMP 430 SM. When both AP types are selected, if the SM does not register to an AP after 10 minutes, it will reboot to scan the other AP type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pmp430(1), pmp450(2), both(3)  

switchRadioModeAndReboot 1.3.6.1.4.1.161.19.3.2.1.146
Setting this to 1 will force switch the SM to the other radio mode and immediately reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Only will be allowed to be set if both registration options are configured. PMP 430 SM only. Introduced in release 12.2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER finishedReboot(0), switchRadioModeAndReboot(1)  

natTslTableSize 1.3.6.1.4.1.161.19.3.2.1.147
NAT Translation Table Size. Range 1024-8192.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1024..8192  

ingressVIDPriority 1.3.6.1.4.1.161.19.3.2.1.148
ingress VID VLAN Priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

ingressVIDPriorityMode 1.3.6.1.4.1.161.19.3.2.1.149
ingress VID VLAN Priority Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1)  

providerVIDPriority 1.3.6.1.4.1.161.19.3.2.1.150
Provider VID VLAN Priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

providerVIDPriorityMode 1.3.6.1.4.1.161.19.3.2.1.151
Provider VID VLAN Priority Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER promote-IP-priority(0), define-priority(1), copy-inner-tag-priority(2)  

additionalColorCode 1.3.6.1.4.1.161.19.3.2.1.152
Add an additional color code. Setting additionalColorCode and additionalColorCodePriority adds an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

additionalColorCodePriority 1.3.6.1.4.1.161.19.3.2.1.153
Add an additional color code priority. Setting additionalColorCode and additionalColorCodePriority adds an entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3)  

deleteAdditionalColorCode 1.3.6.1.4.1.161.19.3.2.1.154
Delete an additional color code.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

bCastMIRUnits 1.3.6.1.4.1.161.19.3.2.1.155
Units of Broadcast/ Multicast MIR value. Set units first and then bCastMIR
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER kbps(0), pps(1)  

rfScanListTable 1.3.6.1.4.1.161.19.3.2.1.156
The list of configured scanning frequencies on the SM or BHS.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RfScanListEntry

rfScanListEntry 1.3.6.1.4.1.161.19.3.2.1.156.1
Entry of configured scanning frequencies on the SM or BHS.
Status: current Access: not-accessible
OBJECT-TYPE    
  RfScanListEntry  

rfScanListFrequency 1.3.6.1.4.1.161.19.3.2.1.156.1.1
RF scan list. The frequencies vary by product and region.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..9000000  

numAuthCerts 1.3.6.1.4.1.161.19.3.2.7.2
can have a max value of 2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

authenticationEnforce 1.3.6.1.4.1.161.19.3.2.7.3
enforce SM to register with specifed Auth Enabled AP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), aaa(1), presharedkey(2)  

phase1 1.3.6.1.4.1.161.19.3.2.7.4
Select the outer method for EAP Authentication. Note: PEAP is not supported for MPC860 platform.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER eapttls(0), eapMSChapV2(1), eappeap(2)  

phase2 1.3.6.1.4.1.161.19.3.2.7.5
Select the outer method for EAP Authentication
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pap(0), chap(1), mschapv2(2)  

authOuterId 1.3.6.1.4.1.161.19.3.2.7.6
EAP Peer Username
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..253)  

authPassword 1.3.6.1.4.1.161.19.3.2.7.7
EAP Peer password
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authUsername 1.3.6.1.4.1.161.19.3.2.7.8
EAP Peer Identity
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

useRealm 1.3.6.1.4.1.161.19.3.2.7.9
Enable or disable the use of realm option.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

realm 1.3.6.1.4.1.161.19.3.2.7.10
EAP Peer Realm
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

certTable 1.3.6.1.4.1.161.19.3.2.7.1
The table of CA Certificates on SM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CertEntry

certEntry 1.3.6.1.4.1.161.19.3.2.7.1.1
Entry of Certifcates.
Status: current Access: not-accessible
OBJECT-TYPE    
  CertEntry  

certIndex 1.3.6.1.4.1.161.19.3.2.7.1.1.1
User information table index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

cert 1.3.6.1.4.1.161.19.3.2.7.1.1.2
0: Inactive 1: Active
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

action 1.3.6.1.4.1.161.19.3.2.7.1.1.3
0: No Operation 1: Delete Certificate
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noop(0), delete(1)  

certificateDN 1.3.6.1.4.1.161.19.3.2.7.1.1.4
Distinguished Name of Certificate 2
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sessionStatus 1.3.6.1.4.1.161.19.3.2.2.1
SM registered or not.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rssi 1.3.6.1.4.1.161.19.3.2.2.2
Radio signal strength index. FSK only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

jitter 1.3.6.1.4.1.161.19.3.2.2.3
A measure of multipath interference. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..15  

airDelay 1.3.6.1.4.1.161.19.3.2.2.4
Round trip delay in bits.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

radioSlicingSm 1.3.6.1.4.1.161.19.3.2.2.5
This variable is deprecated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

radioTxGainSm 1.3.6.1.4.1.161.19.3.2.2.6
Radio transmission gain setting. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

calibrationStatus 1.3.6.1.4.1.161.19.3.2.2.7
Varible deprecated. Please use calibrationStatusBox.
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

radioDbm 1.3.6.1.4.1.161.19.3.2.2.8
Rx Power level. For MIMO this is the combined power of the horizontal and vertical paths.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

registeredToAp 1.3.6.1.4.1.161.19.3.2.2.9
AP MAC address that the SM registered to.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dhcpCip 1.3.6.1.4.1.161.19.3.2.2.10
Assigned IP address to DHCP client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpSip 1.3.6.1.4.1.161.19.3.2.2.11
Public DHCP server IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpClientLease 1.3.6.1.4.1.161.19.3.2.2.12
DHCP client lease time.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

dhcpCSMask 1.3.6.1.4.1.161.19.3.2.2.13
Public DHCP server subnet mask.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpDfltRterIP 1.3.6.1.4.1.161.19.3.2.2.14
Public default router IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpcdns1 1.3.6.1.4.1.161.19.3.2.2.15
Primary public domain name server.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpcdns2 1.3.6.1.4.1.161.19.3.2.2.16
Secondary public domain name server.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpcdns3 1.3.6.1.4.1.161.19.3.2.2.17
Third public domain name server.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpDomName 1.3.6.1.4.1.161.19.3.2.2.18
Public domain name server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

adaptRate 1.3.6.1.4.1.161.19.3.2.2.20
VC adapt rate.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioDbmInt 1.3.6.1.4.1.161.19.3.2.2.21
Radio power level(integer). For MIMO radios this is the combined power of the horiztontal and vertical paths.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dfsStatus 1.3.6.1.4.1.161.19.3.2.2.22
Dynamic frequency shifting status. For DFS Radio only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioTxPwr 1.3.6.1.4.1.161.19.3.2.2.23
Tx Power level. Valid for FSK and OFDM SMs.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

activeRegion 1.3.6.1.4.1.161.19.3.2.2.24
The active region of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

snmpBerLevel 1.3.6.1.4.1.161.19.3.2.2.25
BER level. For PMP 450 systems: 2=MIMO QPSK, 4=MIMO 16-QAM, 6=MIMO64-QAM, 8=256-QAM For non PMP 450: 2=2 level BER, 4=4 level BER.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twoLevelOrMimoQPSK(2), fourLevelOrMimo16QAM(4), mimo64QAM(6), mimo256QAM(8)  

nbBitsRcvd 1.3.6.1.4.1.161.19.3.2.2.26
Number of BER bits received (non MIMO platforms only).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

nbPriBitsErr 1.3.6.1.4.1.161.19.3.2.2.27
Number of Primary bit errors (non MIMO platforms only).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nbSndBitsErr 1.3.6.1.4.1.161.19.3.2.2.28
Number of secondary bit errors (non MIMO platforms only).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

primaryBER 1.3.6.1.4.1.161.19.3.2.2.29
Obsoleted, invalid type to represent this data. Measured Primary Bit Error Rate.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

secondaryBER 1.3.6.1.4.1.161.19.3.2.2.30
Obsoleted, invalid type to represent this data. Measured Secondary Bit Error Rate.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

totalBER 1.3.6.1.4.1.161.19.3.2.2.31
Obsoleted, invalid type to represent this data. Measured Total Bit Error Rate.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

minRSSI 1.3.6.1.4.1.161.19.3.2.2.32
Measured Min. RSSI. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxRSSI 1.3.6.1.4.1.161.19.3.2.2.33
Measured Max. RSSI. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

minJitter 1.3.6.1.4.1.161.19.3.2.2.34
Measured Min. Jitter. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..15  

maxJitter 1.3.6.1.4.1.161.19.3.2.2.35
Measured Max. Jitter. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..15  

smSessionTimer 1.3.6.1.4.1.161.19.3.2.2.36
SM current session timer.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

pppoeSessionStatus 1.3.6.1.4.1.161.19.3.2.2.37
Current PPPoE Session Status
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pppoeSessionID 1.3.6.1.4.1.161.19.3.2.2.38
Current PPPoE Session ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pppoeIPCPAddress 1.3.6.1.4.1.161.19.3.2.2.39
Current PPPoE IPCP IP Address
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

pppoeMTUOverrideEn 1.3.6.1.4.1.161.19.3.2.2.40
Current PPPoE MTU Override Setting
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pppoeMTUValue 1.3.6.1.4.1.161.19.3.2.2.41
Current PPPoE MTU Value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pppoeTimerTypeValue 1.3.6.1.4.1.161.19.3.2.2.42
Current PPPoE Timer Type. 0 is disabled, 1 is Keep Alive timer, and 2 is Idle Timeout timer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), keepAlive(1), idleTimeout(2)  

pppoeTimeoutValue 1.3.6.1.4.1.161.19.3.2.2.43
Current PPPoE Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pppoeDNSServer1 1.3.6.1.4.1.161.19.3.2.2.44
PPPoE DNS Server 1
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

pppoeDNSServer2 1.3.6.1.4.1.161.19.3.2.2.45
PPPoE DNS Server 2
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

pppoeControlBytesSent 1.3.6.1.4.1.161.19.3.2.2.46
PPPoE Control Bytes Sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pppoeControlBytesReceived 1.3.6.1.4.1.161.19.3.2.2.47
PPPoE Control Bytes Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pppoeDataBytesSent 1.3.6.1.4.1.161.19.3.2.2.48
PPPoE Data Bytes Sent
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pppoeDataBytesReceived 1.3.6.1.4.1.161.19.3.2.2.49
PPPoE Data Bytes Received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pppoeEnabledStatus 1.3.6.1.4.1.161.19.3.2.2.50
PPPoE Enabled
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pppoeTCPMSSClampEnableStatus 1.3.6.1.4.1.161.19.3.2.2.51
PPPoE TCP MSS Clamping Enable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pppoeACNameStatus 1.3.6.1.4.1.161.19.3.2.2.52
Current PPPoE Access Concentrator In Use
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pppoeSvcNameStatus 1.3.6.1.4.1.161.19.3.2.2.53
Current PPPoE Service Name In Use
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

pppoeSessUptime 1.3.6.1.4.1.161.19.3.2.2.54
Uptime of current PPPoE Session in ticks
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

primaryBERDisplay 1.3.6.1.4.1.161.19.3.2.2.55
Measured Primary Bit Error Rate. Non MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

secondaryBERDisplay 1.3.6.1.4.1.161.19.3.2.2.56
Measured Secondary Bit Error Rate. FSK platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

totalBERDisplay 1.3.6.1.4.1.161.19.3.2.2.57
Measured Total Bit Error Rate. For MIMO this is combined both paths.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

minRadioDbm 1.3.6.1.4.1.161.19.3.2.2.58
Maximum receive power of beacon in dBm. For MIMO radios, this is only available in the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxRadioDbm 1.3.6.1.4.1.161.19.3.2.2.59
Maximum receive power in dBm (rounded to nearest integer).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pppoeSessIdleTime 1.3.6.1.4.1.161.19.3.2.2.60
Idle Time of current PPPoE Session in ticks
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

radioDbmAvg 1.3.6.1.4.1.161.19.3.2.2.61
Average Receive Power of the AP's beacon in dBm. OFDM Radios only. For MIMO this is only the verical path, as the beacon is not transmitted on horizontal.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

zoltarFPGAFreqOffset 1.3.6.1.4.1.161.19.3.2.2.62
FPGA peek of 70001088
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

zoltarSWFreqOffset 1.3.6.1.4.1.161.19.3.2.2.63
FPGA peek of 7000108C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

airDelayns 1.3.6.1.4.1.161.19.3.2.2.64
Round trip delay in nanoseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

currentColorCode 1.3.6.1.4.1.161.19.3.2.2.65
The current Color Code of the Registered AP/BHM. A value of -1 is return when the device is not registered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

currentColorCodePri 1.3.6.1.4.1.161.19.3.2.2.66
The current priority of the Registered color code
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), primary(1), secondary(2), tertiary(3)  

currentChanFreq 1.3.6.1.4.1.161.19.3.2.2.67
The Current Channel Frequency of the AP/BHM when in session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

linkQualityBeacon 1.3.6.1.4.1.161.19.3.2.2.68
Engineering only. Link Quality for incoming beacons. For Gen II OFDM radios and forward. For PMP 450 and forward this is vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dhcpServerPktXmt 1.3.6.1.4.1.161.19.3.2.2.72
Number of packets transmitted by SM DHCP Server
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpServerPktRcv 1.3.6.1.4.1.161.19.3.2.2.73
Number of packets received by SM DHCP Server
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpServerPktToss 1.3.6.1.4.1.161.19.3.2.2.74
Number of packets tossed by SM DHCP Server
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

receiveFragmentsModulationPercentage 1.3.6.1.4.1.161.19.3.2.2.86
Engineering use only. The percentage of recent fragments received at which modulation. For Gen II OFDM only and forward.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fragmentsReceived1XVertical 1.3.6.1.4.1.161.19.3.2.2.87
Engineering use only. Number of fragments received in 1x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived2XVertical 1.3.6.1.4.1.161.19.3.2.2.88
Engineering use only. Number of fragments received in 2x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived3XVertical 1.3.6.1.4.1.161.19.3.2.2.89
Engineering use only. Number of fragments received in 3x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived4XVertical 1.3.6.1.4.1.161.19.3.2.2.90
Engineering use only. Number of fragments received in 4x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkQualityData1XVertical 1.3.6.1.4.1.161.19.3.2.2.91
Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData2XVertical 1.3.6.1.4.1.161.19.3.2.2.92
Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData3XVertical 1.3.6.1.4.1.161.19.3.2.2.93
Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData4XVertical 1.3.6.1.4.1.161.19.3.2.2.94
Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioSMVertical 1.3.6.1.4.1.161.19.3.2.2.95
An estimated signal to noise ratio based on the last received data. For GenII OFDM only and forward. For MIMO this is the vertical antenna. Will return zero if Signal to Noise Ratio Calculation is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rfStatTxSuppressionCount 1.3.6.1.4.1.161.19.3.2.2.96
RF Scheduler Stats DFS TX Suppression Count
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

bridgecbUplinkCreditRate 1.3.6.1.4.1.161.19.3.2.2.97
Sustained uplink data rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgecbUplinkCreditLimit 1.3.6.1.4.1.161.19.3.2.2.98
Uplink Burst Allocation.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgecbDownlinkCreditRate 1.3.6.1.4.1.161.19.3.2.2.99
Sustained uplink data rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgecbDownlinkCreditLimit 1.3.6.1.4.1.161.19.3.2.2.100
Uplink Burst Allocation.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

mimoQpskBerDisplay 1.3.6.1.4.1.161.19.3.2.2.101
QPSK BER statistics. MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

mimo16QamBerDisplay 1.3.6.1.4.1.161.19.3.2.2.102
16-QAM BER statistics MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

mimo64QamBerDisplay 1.3.6.1.4.1.161.19.3.2.2.103
64-QAM BER statistics MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

mimo256QamBerDisplay 1.3.6.1.4.1.161.19.3.2.2.104
256-QAM BER statistics MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

mimoBerRcvModulationType 1.3.6.1.4.1.161.19.3.2.2.105
Receive modulation type. MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioSMHorizontal 1.3.6.1.4.1.161.19.3.2.2.106
An estimated signal to noise ratio based on the last received data for horizontal antenna. MIMO radios only. Will return zero if Signal to Noise Ratio Calculation is disabled. When operating in MIMO-A will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxRadioDbmDeprecated 1.3.6.1.4.1.161.19.3.2.2.107
This OID was inadvertently moved in 12.0.2. Please use maxRadioDbm. This OID is deprecated and kept for backwards compatibility.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

signalStrengthRatio 1.3.6.1.4.1.161.19.3.2.2.108
Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fragmentsReceived1XHorizontal 1.3.6.1.4.1.161.19.3.2.2.109
Engineering use only. Number of fragments received in 1x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived2XHorizontal 1.3.6.1.4.1.161.19.3.2.2.110
Engineering use only. Number of fragments received in 2x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived3XHorizontal 1.3.6.1.4.1.161.19.3.2.2.111
Engineering use only. Number of fragments received in 3x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

fragmentsReceived4XHorizontal 1.3.6.1.4.1.161.19.3.2.2.112
Engineering use only. Number of fragments received in 4x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkQualityData1XHorizontal 1.3.6.1.4.1.161.19.3.2.2.113
Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData2XHorizontal 1.3.6.1.4.1.161.19.3.2.2.114
Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData3XHorizontal 1.3.6.1.4.1.161.19.3.2.2.115
Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkQualityData4XHorizontal 1.3.6.1.4.1.161.19.3.2.2.116
Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioDbmHorizontal 1.3.6.1.4.1.161.19.3.2.2.117
Receive power level of the horizontal antenna in dBm. MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioDbmVertical 1.3.6.1.4.1.161.19.3.2.2.118
Receive power level of the vertical antenna in dBm. MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

bridgecbDownlinkMaxBurstBitRate 1.3.6.1.4.1.161.19.3.2.2.119
Maximum burst downlink rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgecbUplinkMaxBurstBitRate 1.3.6.1.4.1.161.19.3.2.2.120
Maximum burst uplink Rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

currentCyclicPrefix 1.3.6.1.4.1.161.19.3.2.2.121
The Current Cyclic Prefix of the AP/BHM when in session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one-quarter(0), one-eighth(1), one-sixteenth(2)  

currentBandwidth 1.3.6.1.4.1.161.19.3.2.2.122
The Current Bandwidth of the AP/BHM when in session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bandwidth5mhz(1), bandwidth10mhz(3), bandwidth20mhz(5)  

berPwrRxFPGAPathA 1.3.6.1.4.1.161.19.3.2.2.123
BER power level on FPGA Rx Path A of SM. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

berPwrRxFPGAPathB 1.3.6.1.4.1.161.19.3.2.2.124
BER power level on FPGA Rx Path B of SM. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rawBERPwrRxPathA 1.3.6.1.4.1.161.19.3.2.2.125
Raw unadjusted BER power level on FPGA Rx Path A of SM. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rawBERPwrRxPathB 1.3.6.1.4.1.161.19.3.2.2.126
Raw unadjusted BER power level on FPGA Rx Path B of SM. Engineering Use Only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radioModeStatus 1.3.6.1.4.1.161.19.3.2.2.127
The current radio mode that SM is operating in. PMP 430 SMs only. Introduced in release 12.2.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(0), pmp430(1), pmp450Interoperability(2)  

adaptRateLowPri 1.3.6.1.4.1.161.19.3.2.2.128
The current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSession(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)  

adaptRateHighPri 1.3.6.1.4.1.161.19.3.2.2.129
The current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noHighPriorityChannel(-1), noSession(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)  

bitErrorsQSPKpathA 1.3.6.1.4.1.161.19.3.2.2.130
Number of bit errors received from BER packet at QPSK path A. Valid MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrorsQSPKpathB 1.3.6.1.4.1.161.19.3.2.2.131
Number of bit errors received from BER packet at QPSK path B. Valid MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors16QAMpathA 1.3.6.1.4.1.161.19.3.2.2.132
Number of bit errors received from BER packet at 16-QAM path A. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors16QAMpathB 1.3.6.1.4.1.161.19.3.2.2.133
Number of bit errors received from BER packet at 16-QAM path B. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors64QAMpathA 1.3.6.1.4.1.161.19.3.2.2.134
Number of bit errors received from BER packet at 64-QAM path A. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors64QAMpathB 1.3.6.1.4.1.161.19.3.2.2.135
Number of bit errors received from BER packet at 64-QAM path B. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors256QAMpathA 1.3.6.1.4.1.161.19.3.2.2.136
Number of bit errors received from BER packet at 256-QAM path A. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitErrors256QAMpathB 1.3.6.1.4.1.161.19.3.2.2.137
Number of bit errors received from BER packet at 256-QAM path B. Valid MIMO platforms only. Engineering use only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bitsReceivedPerPathModulation 1.3.6.1.4.1.161.19.3.2.2.138
Number of bit received from BER. To calculate Bit Error Rate, take bit errors at a modulation and path and divide by this OID. To get combined BER add errors and divide by this multiplied by each path and modulation. i.e. MIMO QPSK combined BER = ((errors on path A) + (errors on path B))/(bits recieved per path modulation * 2) Valid MIMO platforms only.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

beaconsPercentReceived 1.3.6.1.4.1.161.19.3.2.2.139
The current percentage of beacons that the SM/BHS successfully receiving.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

mapsPercentReceived 1.3.6.1.4.1.161.19.3.2.2.140
PMP 450 only. The current percentage of scheduling maps that the SM/BHS successfully receiving.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

natTslTableEntries 1.3.6.1.4.1.161.19.3.2.2.141
Number of Entries in NAT Translation Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxReceivePower 1.3.6.1.4.1.161.19.3.2.2.142
Maximum receive power level for this session. MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

beaconsPercentMinReceived 1.3.6.1.4.1.161.19.3.2.2.143
The percentage of the least number of beacons that the SM/BHS successfully received in a 16 second window for the last 15 minutes. This will be updated only once in 15 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

beaconsPercentMaxReceived 1.3.6.1.4.1.161.19.3.2.2.144
The percentage of the maximum number of beacons that the SM/BHS successfully received in a 16 second window for the last 15 minutes. This will be updated only once in 15 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

beaconsPercentReceivedSnapshot 1.3.6.1.4.1.161.19.3.2.2.145
The percentage of beacons that the SM/BHS successfully received for the last 15 minutes. This will be updated only once in 15 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

dhcpServerTable 1.3.6.1.4.1.161.19.3.2.2.19
The table of DHCP server hosts.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpServerEntry

dhcpServerEntry 1.3.6.1.4.1.161.19.3.2.2.19.1
Entry of DHCP server hosts.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpServerEntry  

hostIp 1.3.6.1.4.1.161.19.3.2.2.19.1.1
DHCP server IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hostMacAddress 1.3.6.1.4.1.161.19.3.2.2.19.1.2
Private host MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

hostLease 1.3.6.1.4.1.161.19.3.2.2.19.1.3
Lease time assigned by DHCP server host.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

whispSmConfigGroup 1.3.6.1.4.1.161.19.3.2.3.1
Canopy Subscriber Module configuration group.
Status: current Access: read-only
OBJECT-GROUP    

whispSmStatusGroup 1.3.6.1.4.1.161.19.3.2.3.2
Canopy Subscriber Module status group.
Status: current Access: read-only
OBJECT-GROUP    

whispSmNotifGroup 1.3.6.1.4.1.161.19.3.2.3.3
WHiSP SMs notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

whispMappingTableGroup 1.3.6.1.4.1.161.19.3.2.3.4
Canopy SM NAT port mapping Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispRadarDetected 1.3.6.1.4.1.161.19.3.2.4.1.1
Radar detected transmit stopped.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispRadarEnd 1.3.6.1.4.1.161.19.3.2.4.1.2
Radar ended back to normal transmit.
Status: current Access: read-only
NOTIFICATION-TYPE    

enterSpectrumAnalysis 1.3.6.1.4.1.161.19.3.2.4.2.1
Entering spectrum analysis. physAddress - MAC address of the SM
Status: current Access: read-only
NOTIFICATION-TYPE    

availableSpectrumAnalysis 1.3.6.1.4.1.161.19.3.2.4.2.2
Spectrum analysis is complete, SM is re-registered with AP and results are available. physAddress - MAC address of the SM
Status: current Access: read-only
NOTIFICATION-TYPE    

smNatWanDHCPClientEvent 1.3.6.1.4.1.161.19.3.2.4.3.1
NAT WAN DHCP Client has received a new address via DHCP.
Status: current Access: read-only
NOTIFICATION-TYPE    

smNatRFPubDHCPClientEvent 1.3.6.1.4.1.161.19.3.2.4.3.2
NAT RF Public DHCP Client has received a new address via DHCP.
Status: current Access: read-only
NOTIFICATION-TYPE    

clearLinkStats 1.3.6.1.4.1.161.19.3.2.8.1
Setting this to a nonzero value will clear the link stats.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rescan 1.3.6.1.4.1.161.19.3.2.8.2
Setting this to a nonzero value will start the rescan. Warning: If currently connected, this will cause the SM/BHS to drop session
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

whispMappingTable 1.3.6.1.4.1.161.19.3.2.5
NAT port mapping information table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispMappingEntry

whispMappingEntry 1.3.6.1.4.1.161.19.3.2.5.1
Mapping table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispMappingEntry  

tableIndex 1.3.6.1.4.1.161.19.3.2.5.1.1
User information table index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

protocol 1.3.6.1.4.1.161.19.3.2.5.1.2
Protocol type: 0:both UDP and TCP, 1:UDP, 2:TCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

port 1.3.6.1.4.1.161.19.3.2.5.1.3
Application port number. e.g. 23=telnet, 21=ftp etc. Should be a positive integer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

localIp 1.3.6.1.4.1.161.19.3.2.5.1.4
IP of local host to which the incoming packet mapped to an application should be forwarded.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

whispSmTranslationTable 1.3.6.1.4.1.161.19.3.2.6
Translation Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispSmTranslationTableEntry

whispSmTranslationTableEntry 1.3.6.1.4.1.161.19.3.2.6.1
Translation Table Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispSmTranslationTableEntry  

whispTranslationTableIndex 1.3.6.1.4.1.161.19.3.2.6.1.1
Index into translation table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..127  

whispTranslationTableMacAddr 1.3.6.1.4.1.161.19.3.2.6.1.2
MAC Address of the registered enity.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

whispTranslationTableIpAddr 1.3.6.1.4.1.161.19.3.2.6.1.3
Ip Address of the registered entity.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

whispTranslationTableAge 1.3.6.1.4.1.161.19.3.2.6.1.4
Age of the registered entity.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

whispSmColorCodeTable 1.3.6.1.4.1.161.19.3.2.9
Additional color code Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispSmColorCodeEntry

whispSmColorCodeEntry 1.3.6.1.4.1.161.19.3.2.9.1
Additional Color code Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispSmColorCodeEntry  

entryColorCode 1.3.6.1.4.1.161.19.3.2.9.1.1
color code.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..254  

entryColorCodePriority 1.3.6.1.4.1.161.19.3.2.9.1.2
color code priority.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), tertiary(3)  

whispSmAPEvalTable 1.3.6.1.4.1.161.19.3.2.10
AP Eval List.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispSmAPEvalEntry

whispSmAPEvalEntry 1.3.6.1.4.1.161.19.3.2.10.1
Evaluation of AP and BHM Entries
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispSmAPEvalEntry  

evalIndex 1.3.6.1.4.1.161.19.3.2.10.1.1
Index of the radio seen in the scan
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

evalFrequency 1.3.6.1.4.1.161.19.3.2.10.1.2
Transmit Frequency in KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalChannelBandwidth 1.3.6.1.4.1.161.19.3.2.10.1.3
Channel Bandwidth
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bandwidth3Point5MHz(0), bandwidth5MHz(1), bandwidth7MHz(2), bandwidth10MHz(3), bandwidth15MHz(4), bandwidth20MHz(5), bandwidth30MHz(6), bandwidth40MHz(7)  

evalCyclicPrefix 1.3.6.1.4.1.161.19.3.2.10.1.4
Cyclic Prefix value, for OFDM Radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one-quarter(0), one-eighth(1), one-sixteenth(2)  

evalESN 1.3.6.1.4.1.161.19.3.2.10.1.5
Radio ESN
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

evalRegion 1.3.6.1.4.1.161.19.3.2.10.1.6
Region
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

evalBeaconReceivePowerCombined 1.3.6.1.4.1.161.19.3.2.10.1.7
Beacon Receive Power Combined in dBm(rounded to nearest integer)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalBeaconReceivePowerH 1.3.6.1.4.1.161.19.3.2.10.1.8
Beacon Receive Power in dBm(rounded to nearest integer) for Path H(MIMO Radios only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalBeaconReceivePowerV 1.3.6.1.4.1.161.19.3.2.10.1.9
Beacon Receive Power in dBm(rounded to nearest integer) for Path V(MIMO Radios only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalFECEnable 1.3.6.1.4.1.161.19.3.2.10.1.10
Forward Error Correction Enabled Status. Note, this is always enabled on 450 and forward.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

evalType 1.3.6.1.4.1.161.19.3.2.10.1.11
Radio Type (Point-to-Point or Multipoint)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER multipoint(0), point-to-point(1)  

evalAvail 1.3.6.1.4.1.161.19.3.2.10.1.12
Returns True if seen on the previous SM's scan
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

evalAge 1.3.6.1.4.1.161.19.3.2.10.1.13
Number of minutes since index was last seen
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalLockout 1.3.6.1.4.1.161.19.3.2.10.1.14
Number of minutes radio is currently locked out
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalRegFail 1.3.6.1.4.1.161.19.3.2.10.1.15
Registration Fail Count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalRange 1.3.6.1.4.1.161.19.3.2.10.1.16
Range in feet
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalMaxRange 1.3.6.1.4.1.161.19.3.2.10.1.17
Max Range is in miles
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalTxBER 1.3.6.1.4.1.161.19.3.2.10.1.18
Radio is transmitting Bit Error Rate symbol or not Note: This is always enabled on 450 and forward
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

evalEBCast 1.3.6.1.4.1.161.19.3.2.10.1.19
Broadcast Encryption status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

evalSessionCount 1.3.6.1.4.1.161.19.3.2.10.1.20
Session Count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalNoLuid 1.3.6.1.4.1.161.19.3.2.10.1.21
Number of times the registration request has been rejected due to No Luid
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalOutOfRange 1.3.6.1.4.1.161.19.3.2.10.1.22
Number of times the registration request has been rejected due to out of range
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalAuthFail 1.3.6.1.4.1.161.19.3.2.10.1.23
Number of times the registration request has been rejected due to authentication failure
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalEncryptFail 1.3.6.1.4.1.161.19.3.2.10.1.24
Number of times the registration request has been rejected due to encrypt fail
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalReScanReq 1.3.6.1.4.1.161.19.3.2.10.1.25
Rescan request count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalLimitReached 1.3.6.1.4.1.161.19.3.2.10.1.26
Number of times failed when trying to register with an limited AP maxed out
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalNoVCs 1.3.6.1.4.1.161.19.3.2.10.1.27
Number of times the registration request has been rejected due to No VCs
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalVCReserveFail 1.3.6.1.4.1.161.19.3.2.10.1.28
Number of times the registration request has been rejected due to VC reserve fail
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalVCActFail 1.3.6.1.4.1.161.19.3.2.10.1.29
Number of times the registration request has been rejected due to VC activate fail
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalTxPower 1.3.6.1.4.1.161.19.3.2.10.1.30
Transmit Power in dBm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalReceiveTargetLevel 1.3.6.1.4.1.161.19.3.2.10.1.31
Receive Target Level(in dBm)(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalColorCode 1.3.6.1.4.1.161.19.3.2.10.1.32
Color Code
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalBeaconVersion 1.3.6.1.4.1.161.19.3.2.10.1.33
Beacon Version
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalSectorUserCount 1.3.6.1.4.1.161.19.3.2.10.1.34
Sector User Count(AP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalSyncSrc 1.3.6.1.4.1.161.19.3.2.10.1.35
Sync Source(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER generate-sync(0), gps-sync(1)  

evalNumULSlots 1.3.6.1.4.1.161.19.3.2.10.1.36
Number of uplink slots
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalNumDLSlots 1.3.6.1.4.1.161.19.3.2.10.1.37
Number of downlink slots
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalNumULContSlots 1.3.6.1.4.1.161.19.3.2.10.1.38
Number of uplink contention slots(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

evalICC 1.3.6.1.4.1.161.19.3.2.10.1.39
Instalaton Color Code(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

evalAuthentication 1.3.6.1.4.1.161.19.3.2.10.1.40
Authentication Setting(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

evalSMPPPoE 1.3.6.1.4.1.161.19.3.2.10.1.41
SM PPPoE status(PMP only)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-supported(0), suported(1)  

evalPToPVLAN 1.3.6.1.4.1.161.19.3.2.10.1.42
PToP VLAN
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-supported(0), suported(1)  

evalFramePeriod 1.3.6.1.4.1.161.19.3.2.10.1.43
Frame Period
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twoPointFiveMs(0), fiveMs(1)