WLSX-TRAP-MIB

File: WLSX-TRAP-MIB.mib (143148 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
ARUBA-MIB ARUBA-TC

Imported symbols

TEXTUAL-CONVENTION MODULE-IDENTITY OBJECT-TYPE
snmpModules Integer32 Counter32
IpAddress NOTIFICATION-TYPE TDomain
DisplayString PhysAddress TAddress
TimeInterval RowStatus StorageType
TestAndIncr MacAddress DateAndTime
TruthValue OBJECT-GROUP wlsrEnterpriseMibModules
ArubaFrameType ArubaAddressType ArubaEnableValue
ArubaOperStateValue ArubaBlackListReason ArubaDBType
ArubaVrrpState ArubaSwitchRole ArubaAuthenticationMethods
ArubaConfigurationState ArubaConfigurationChangeType ArubaHTExtChannel
ArubaAccessPointMode ArubaARMChangeReason ArubaAPMasterStatus
ArubaStationType ArubaThresholdResourceType ArubaStackState
ArubaStackChangeEvent ArubaStackIfTopoJoined InterfaceIndex
ArubaIfState ArubaIfStateChangeReason ArubaAPUplinkType
TimeTicks ArubaAPUplinkChangeReason

Defined Values

wlsrTrapMIB 1.3.6.1.4.1.14823.2.3.1.11
This MIB defines the Traps generated by the switch.
MODULE-IDENTITY    

wlsxTrapsGroup 1.3.6.1.4.1.14823.2.3.1.11.1
OBJECT IDENTIFIER    

wlsxTrapObjectsGroup 1.3.6.1.4.1.14823.2.3.1.11.1.1
OBJECT IDENTIFIER    

wlsxTrapDefinitionsGroup 1.3.6.1.4.1.14823.2.3.1.11.1.2
OBJECT IDENTIFIER    

wlsxTrapAPMacAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.1
This object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapAPIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.2
This object is used in the traps to indicate the IP address of an access point, for which the trap is being raised.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapAPBSSID 1.3.6.1.4.1.14823.2.3.1.11.1.1.3
This object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapEssid 1.3.6.1.4.1.14823.2.3.1.11.1.1.4
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTargetAPBSSID 1.3.6.1.4.1.14823.2.3.1.11.1.1.5
This object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapTargetAPSSID 1.3.6.1.4.1.14823.2.3.1.11.1.1.6
This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTargetAPChannel 1.3.6.1.4.1.14823.2.3.1.11.1.1.7
This object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an air monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapNodeMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.8
This object is used in the traps to indicate the MAC address of a node.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapSourceMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.9
This object is used in the traps to indicate the MAC address of the source.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxReceiverMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.10
This object is used in the traps to indicate the MAC address of the receiver.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapTransmitterMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.11
This object is used in the traps to indicate the MAC address of the transmitter.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapReceiverMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.12
This object is used in the traps to indicate the MAC address of the receiver.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapSnr 1.3.6.1.4.1.14823.2.3.1.11.1.1.13
This object is used in the traps to indicate the Signal to Noise ratio.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapSignatureName 1.3.6.1.4.1.14823.2.3.1.11.1.1.14
This object is used in the traps to indicate the Signature Name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapFrameType 1.3.6.1.4.1.14823.2.3.1.11.1.1.15
This object is used in the traps to indicate the Frame Type
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaFrameType  

wlsxTrapAddressType 1.3.6.1.4.1.14823.2.3.1.11.1.1.16
This object is used in the traps to indicate the Address type.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAddressType  

wlsxTrapAPLocation 1.3.6.1.4.1.14823.2.3.1.11.1.1.17
This object is used in the traps to indicate the Location of the AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapAPChannel 1.3.6.1.4.1.14823.2.3.1.11.1.1.18
This object is used in the traps to indicate the Current Channel.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAPTxPower 1.3.6.1.4.1.14823.2.3.1.11.1.1.19
This object is used in the traps to indicate the AP Transmit Power.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapMatchedMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.20
This object is used in the traps to indicate the MAC address
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapMatchedIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.21
This object is used in the traps to indicate the IP address
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapRogueIfoURL 1.3.6.1.4.1.14823.2.3.1.11.1.1.22
This object is used to point to the WEBUI Rogue AP information URL.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapVlanId 1.3.6.1.4.1.14823.2.3.1.11.1.1.23
This object is used in the traps to indicate the VLAN Id.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAdminStatus 1.3.6.1.4.1.14823.2.3.1.11.1.1.24
This object is used in the traps to indicate the admin status of VLAN.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaEnableValue  

wlsxTrapOperStatus 1.3.6.1.4.1.14823.2.3.1.11.1.1.25
This object is used in the traps to indicate the admin status of VLAN.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaOperStateValue  

wlsxTrapAuthServerName 1.3.6.1.4.1.14823.2.3.1.11.1.1.26
This object is used in the traps to indicate the Authentication Server used for Authentication.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapAuthServerTimeout 1.3.6.1.4.1.14823.2.3.1.11.1.1.27
This object is used in the traps to indicate the Authentication Server Timeout.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapCardSlot 1.3.6.1.4.1.14823.2.3.1.11.1.1.28
This object is used in the traps to indicate the Slot in which this card is present.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapTemperatureValue 1.3.6.1.4.1.14823.2.3.1.11.1.1.29
This object is used in the traps to indicate the Temperature Value.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapProcessName 1.3.6.1.4.1.14823.2.3.1.11.1.1.30
This object is used in the traps to indicate the Process name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapFanNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.31
This object is used in the traps to indicate the Fan Number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapVoltageType 1.3.6.1.4.1.14823.2.3.1.11.1.1.32
This object is used in the traps to indicate the type of Voltage.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapVoltageValue 1.3.6.1.4.1.14823.2.3.1.11.1.1.33
This object is used in the traps to indicate the voltage value in Float.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapStationBlackListReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.34
The Reason for which a station is black listed.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaBlackListReason  

wlsxTrapSpoofedIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.35
This object is used in a trap to identify a spoofed IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapSpoofedOldPhyAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.36
This object is used in a trap to identify an old MAC address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapSpoofedNewPhyAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.37
This object is used in a trap to identify a New MAC address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapDBName 1.3.6.1.4.1.14823.2.3.1.11.1.1.38
This object is used in a trap to identify name of the database.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapDBUserName 1.3.6.1.4.1.14823.2.3.1.11.1.1.39
This object is used in a trap to identify name of the database user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapDBIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.40
This object is used in a trap to identify the IpAddress of the Database.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapDBType 1.3.6.1.4.1.14823.2.3.1.11.1.1.41
This object is used in a trap to identify the port of the user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaDBType  

wlsxTrapVrrpID 1.3.6.1.4.1.14823.2.3.1.11.1.1.42
This object contains the Virtual Router Identifier.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapVrrpMasterIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.43
This object contains the Master IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapVrrpOperState 1.3.6.1.4.1.14823.2.3.1.11.1.1.44
This object represents the VRRP Operational state.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaVrrpState  

wlsxTrapESIServerGrpName 1.3.6.1.4.1.14823.2.3.1.11.1.1.45
This object represents the External Services Interface (ESI) Server Group name
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapESIServerName 1.3.6.1.4.1.14823.2.3.1.11.1.1.46
This object represents the External Services Interface (ESI) Server Name
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapESIServerIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.47
This object represents the External Services Interface (ESI) Server IP address
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapLicenseDaysRemaining 1.3.6.1.4.1.14823.2.3.1.11.1.1.48
This object represents number of the days remaining prior to a license expiry.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapSwitchIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.49
This object represents the controller IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapSwitchRole 1.3.6.1.4.1.14823.2.3.1.11.1.1.50
This object represents the Role of the controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaSwitchRole  

wlsxTrapUserIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.51
This object represents IP address of the User.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapUserPhyAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.52
This object represents MAC address of the User.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapUserName 1.3.6.1.4.1.14823.2.3.1.11.1.1.53
This object represents the user name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapUserRole 1.3.6.1.4.1.14823.2.3.1.11.1.1.54
This object represents the Authentication method of the user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapUserAuthenticationMethod 1.3.6.1.4.1.14823.2.3.1.11.1.1.55
This object represents the Authentication method of the user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAuthenticationMethods  

wlsxTrapAPRadioNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.56
This object represents the radio number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapRogueInfoURL 1.3.6.1.4.1.14823.2.3.1.11.1.1.57
This object is used to point to the WEBGUI Rogue AP information URL.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapInterferingAPInfoURL 1.3.6.1.4.1.14823.2.3.1.11.1.1.58
This object is used to point to the WEBGUI Rogue interfering AP information URL.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapPortNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.59
This object is used in the traps to indicate the port number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapTime 1.3.6.1.4.1.14823.2.3.1.11.1.1.60
This object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DateAndTime  

wlsxTrapHostIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.61
This object represents the Trap host.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapHostPort 1.3.6.1.4.1.14823.2.3.1.11.1.1.62
This object represents the Trap host port.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapConfigurationId 1.3.6.1.4.1.14823.2.3.1.11.1.1.63
This object represents the ID of the configuration, to be used in traps.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapCTSURL 1.3.6.1.4.1.14823.2.3.1.11.1.1.64
This object represents the URL from which the transfer should happen.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapCTSTransferType 1.3.6.1.4.1.14823.2.3.1.11.1.1.65
This object represents the transfer type, upload or download.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapConfigurationState 1.3.6.1.4.1.14823.2.3.1.11.1.1.66
This object represents state of the configuration transfer.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaConfigurationState  

wlsxTrapUpdateFailureReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.67
This object represents the reason for the update failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapUpdateFailedObj 1.3.6.1.4.1.14823.2.3.1.11.1.1.68
This variable represents the AMAPI object which is the reason for the the update failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTableEntryChangeType 1.3.6.1.4.1.14823.2.3.1.11.1.1.69
This object represents type of the configuration change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaConfigurationChangeType  

wlsxTrapGlobalConfigObj 1.3.6.1.4.1.14823.2.3.1.11.1.1.70
This variable represents the AMAPI object corresponding to the global configuration change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTableGenNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.71
This object represents generation number of a table. Used in the MMS, to keep track of the table content changes.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapLicenseId 1.3.6.1.4.1.14823.2.3.1.11.1.1.72
This object is used in the traps to indicate the license ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapConfidenceLevel 1.3.6.1.4.1.14823.2.3.1.11.1.1.73
This object is used in the traps to indicate the Confidence Level as a percentage
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapMissingLicenses 1.3.6.1.4.1.14823.2.3.1.11.1.1.74
This variable indicates any licenses that are not present during a configuration update
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxVoiceCurrentNumCdr 1.3.6.1.4.1.14823.2.3.1.11.1.1.75
This object represents the number of CDRs in buffer.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapTunnelId 1.3.6.1.4.1.14823.2.3.1.11.1.1.76
This Object represents the tunnel ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapTunnelStatus 1.3.6.1.4.1.14823.2.3.1.11.1.1.77
This Object represents the tunnel Status.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapTunnelUpReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.78
This Object represents the tunnel up reason.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTunnelDownReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.79
This Object represents the tunnel down reason.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapApSerialNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.80
This object represents the AP Serial Number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapTimeStr 1.3.6.1.4.1.14823.2.3.1.11.1.1.81
This object represents the Time in String format.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapMasterIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.82
This object represents the master IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapLocalIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.83
This object represents the Local IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapMasterName 1.3.6.1.4.1.14823.2.3.1.11.1.1.84
This object represents the master controller name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapLocalName 1.3.6.1.4.1.14823.2.3.1.11.1.1.85
This object represents the local controller name.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapPrimaryControllerIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.86
This object represents the IP address of the AP's primary controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapBackupControllerIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.87
This object represents the IP address of the AP's backup controller.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapSpoofedFrameType 1.3.6.1.4.1.14823.2.3.1.11.1.1.88
This object is used in the traps to indicate the Spoofed Frame Type
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapAssociationType 1.3.6.1.4.1.14823.2.3.1.11.1.1.89
This object is used in the traps to indicate the type of association
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapDeviceIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.90
This object represents the IP address of a device seen by an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapDeviceMac 1.3.6.1.4.1.14823.2.3.1.11.1.1.91
This object represents the MAC address of a device seen by an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapVcIpAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.92
This object represents the Ip Address of a Voice client.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapVcMacAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.93
This object represents the MAC address of a Voice client.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxTrapAPName 1.3.6.1.4.1.14823.2.3.1.11.1.1.94
This object is used in the traps to indicate the Name of the AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapApMode 1.3.6.1.4.1.14823.2.3.1.11.1.1.95
This Object represents the AP Mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAPPrevChannel 1.3.6.1.4.1.14823.2.3.1.11.1.1.96
This object is used in the traps to indicate the Previous Channel.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAPPrevChannelSec 1.3.6.1.4.1.14823.2.3.1.11.1.1.97
This object is used in the traps to indicate the Previous Secondary Channel.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaHTExtChannel  

wlsxTrapAPPrevTxPower 1.3.6.1.4.1.14823.2.3.1.11.1.1.98
This object is used in the traps to indicate previous AP Transmit Power.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAPCurMode 1.3.6.1.4.1.14823.2.3.1.11.1.1.99
This Object represents the APs Current Mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAccessPointMode  

wlsxTrapAPPrevMode 1.3.6.1.4.1.14823.2.3.1.11.1.1.100
This Object represents the APs Previous Mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAccessPointMode  

wlsxTrapAPARMChangeReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.101
This Object represents the APs Previous Mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaARMChangeReason  

wlsxTrapAPChannelSec 1.3.6.1.4.1.14823.2.3.1.11.1.1.102
This object is used in the traps to indicate the Current Secondary Channel.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaHTExtChannel  

wlsxTrapUserAttributeChangeType 1.3.6.1.4.1.14823.2.3.1.11.1.1.103
This object represents type of the configuration change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaConfigurationChangeType  

wlsxTrapApControllerIp 1.3.6.1.4.1.14823.2.3.1.11.1.1.104
IP address of the controller to which the AP is (or was most recently) registered.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxTrapApMasterStatus 1.3.6.1.4.1.14823.2.3.1.11.1.1.105
Status of the AP as seen by the master when the status changes.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAPMasterStatus  

wlsxTrapCaName 1.3.6.1.4.1.14823.2.3.1.11.1.1.106
This object is used in the traps to indicate the name of the trustpoint.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapCrlName 1.3.6.1.4.1.14823.2.3.1.11.1.1.107
This object is used in the traps to indicate the name of the crl.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapCount 1.3.6.1.4.1.14823.2.3.1.11.1.1.108
This object represents the number of occurrence of this trap.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapPowerSupplyNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.109
This object represents the power supply number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapFanTrayNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.110
This object represents the Fan Tray number.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapClientClassification 1.3.6.1.4.1.14823.2.3.1.11.1.1.111
This object is used in the traps to indicate the classification of the client.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaStationType  

wlsxThresholdResourceType 1.3.6.1.4.1.14823.2.3.1.11.1.1.112
This object represents the Threshold alert's Resource Type .
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaThresholdResourceType  

wlsxThresholdResourceName 1.3.6.1.4.1.14823.2.3.1.11.1.1.113
This object represents the Threshold alert's Resource Name .
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxThresholdValue 1.3.6.1.4.1.14823.2.3.1.11.1.1.114
This object represents the Threshold alert's set threshold value.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxResourceValue 1.3.6.1.4.1.14823.2.3.1.11.1.1.115
This object represents the Threshold alert's actual value.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxStackPrevSlot 1.3.6.1.4.1.14823.2.3.1.11.1.1.116
This object specifies the slot number of this stack element prior to topology change in stack. A value of -1 indicates that this slot was not in Active state of stack prior to topology change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxStackCurrentSlot 1.3.6.1.4.1.14823.2.3.1.11.1.1.117
This object specifies the slot number of this stack element after the topology change in stack. A value of -1 indicates that this slot is not in Active state of stack after the topology change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxStackPrevState 1.3.6.1.4.1.14823.2.3.1.11.1.1.118
This object specifies the state of this stack element prior to topology change in stack.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaStackState  

wlsxStackCurrentState 1.3.6.1.4.1.14823.2.3.1.11.1.1.119
This object specifies the state of this stack element after topology change in stack.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaStackState  

wlsxStackChangeEvent 1.3.6.1.4.1.14823.2.3.1.11.1.1.120
This object specifies the event which caused change in topology in stack.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaStackChangeEvent  

wlsxStackProtoIfTopoJoined 1.3.6.1.4.1.14823.2.3.1.11.1.1.121
This object specifies whether an interface has joined the stacking topology or left the topology.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaStackIfTopoJoined  

wlsxStackMemberMacAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.122
This object specifies mac-address of this stack element.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

wlsxStackMemberSlotNumber 1.3.6.1.4.1.14823.2.3.1.11.1.1.123
This object specifies the slot number of this element in stack.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxStackIfName 1.3.6.1.4.1.14823.2.3.1.11.1.1.124
This object specifies the interface name which is part of stacking link connected to other stacking element.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapLicenseServerDaysRemaining 1.3.6.1.4.1.14823.2.3.1.11.1.1.125
This object represents number of the days remaining prior to expiry of license limits sent by the server.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapLicenseClientDaysRemaining 1.3.6.1.4.1.14823.2.3.1.11.1.1.126
This object represents number of the days remaining prior to expiry of licenses contributed by a license client.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxIfIndex 1.3.6.1.4.1.14823.2.3.1.11.1.1.127
This object specifies the ifIndex.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

wlsxIfState 1.3.6.1.4.1.14823.2.3.1.11.1.1.128
This object specifies the state of an interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaIfState  

wlsxIfStateChangeReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.129
This object specifies the reason for interface state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaIfStateChangeReason  

wlsxTrapAPPreviousUplinkType 1.3.6.1.4.1.14823.2.3.1.11.1.1.130
This object specifies the up link type for an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAPUplinkType  

wlsxTrapAPPreviousUplinkActiveTime 1.3.6.1.4.1.14823.2.3.1.11.1.1.131
This object specifies the up link type for an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TimeTicks  

wlsxTrapAPActiveUplinkType 1.3.6.1.4.1.14823.2.3.1.11.1.1.132
This object specifies the up link type for an AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAPUplinkType  

wlsxTrapAPUplinkChangeReason 1.3.6.1.4.1.14823.2.3.1.11.1.1.133
This object specifies the up link change reason.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  ArubaAPUplinkChangeReason  

wlsxTrapExpiringCertName 1.3.6.1.4.1.14823.2.3.1.11.1.1.134
This object is used in the traps to indicate the name of the certificate that is expiring in less than 60 days.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapExpiredCertName 1.3.6.1.4.1.14823.2.3.1.11.1.1.135
This object is used in the traps to indicate the name of the certificate that has expired.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapHTMode 1.3.6.1.4.1.14823.2.3.1.11.1.1.136
This object represents HT Mode.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapPhyType 1.3.6.1.4.1.14823.2.3.1.11.1.1.137
This object represents Physical Type.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

wlsxTrapAPManagedModeConfigFailure 1.3.6.1.4.1.14823.2.3.1.11.1.1.138
This object indicates the error for the failure of config apply on IAP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

wlsxTrapAuthServerAddress 1.3.6.1.4.1.14823.2.3.1.11.1.1.139
This object is used in the traps to indicate the Authentication Server IP used for Authentication.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

wlsxVlanLinkUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1000
This trap indicates that a VLAN interface is up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxVlanLinkDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1001
This trap indicates that a VLAN interface is down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignatureMatch 1.3.6.1.4.1.14823.2.3.1.11.1.2.1002
This trap indicates that a signature match was detected.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNodeRateAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1003
This trap indicates that a node is exceeding the threshold set for the frame type.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNormalTemperature 1.3.6.1.4.1.14823.2.3.1.11.1.2.1004
This trap indicates that the Temperature has returned to an acceptable range.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxProcessRestart 1.3.6.1.4.1.14823.2.3.1.11.1.2.1005
This trap indicates that the named process has been restarted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFlashSpaceOK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1006
This trap which indicates that the system flash space is back to a sufficient level.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMemoryUsageOK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1007
This trap which indicates that the free memory usage is back to a sufficient level.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPowerSupplyOK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1008
This trap indicates that the system power supply condition have returned to normal operation status.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFanOK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1009
This trap indicates that the fan has returned to normal.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInRangeVoltage 1.3.6.1.4.1.14823.2.3.1.11.1.2.1010
This trap indicates that the controller Voltage is back within range.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCoverageHoleResolved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1011
This trap indicates that a coverage hole at location wlsxTrapAPLocation has been resolved.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSwitchIPChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1012
This trap indicates that the controller IP address has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSwitchRoleChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1013
This trap indicates that the role of the controller IP address has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNUserEntryCreated 1.3.6.1.4.1.14823.2.3.1.11.1.2.1014
This trap indicates that a new user was created.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNUserEntryDeleted 1.3.6.1.4.1.14823.2.3.1.11.1.2.1015
This trap indicates that a user was deleted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNUserEntryAuthenticated 1.3.6.1.4.1.14823.2.3.1.11.1.2.1016
This trap indicates that a user is Authenticated.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNUserEntryDeAuthenticated 1.3.6.1.4.1.14823.2.3.1.11.1.2.1017
This trap indicates that a user is Deauthenticated.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNUserAuthenticationFailed 1.3.6.1.4.1.14823.2.3.1.11.1.2.1018
This trap indicates that a user authentication has failed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthServerReqTimedOut 1.3.6.1.4.1.14823.2.3.1.11.1.2.1019
This trap indicates that the authentication server request timed out.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthServerTimedOut 1.3.6.1.4.1.14823.2.3.1.11.1.2.1020
This trap indicates that the authentication server timed out.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthServerIsUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1021
This trap indicates that an authentication server is up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthMaxUserEntries 1.3.6.1.4.1.14823.2.3.1.11.1.2.1022
A trap which indicates that the user entries table is full and cannot add any more entries.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthMaxAclEntries 1.3.6.1.4.1.14823.2.3.1.11.1.2.1023
A trap which indicates that the ACL Entries table is full and cannot add any more entries.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthMaxBWContracts 1.3.6.1.4.1.14823.2.3.1.11.1.2.1024
A trap which indicates that the controller reached the maximum number of configurable Bandwidth contracts.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNPowerSupplyFailure 1.3.6.1.4.1.14823.2.3.1.11.1.2.1025
A trap which indicates that the power supply has failed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNFanFailure 1.3.6.1.4.1.14823.2.3.1.11.1.2.1026
A trap which indicates that the fan has failed or is missing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNOutOfRangeVoltage 1.3.6.1.4.1.14823.2.3.1.11.1.2.1027
A trap which indicates that the controller voltage is out of range.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNOutOfRangeTemperature 1.3.6.1.4.1.14823.2.3.1.11.1.2.1028
A trap which indicates that the controller internal temperature is out of range.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNLCInserted 1.3.6.1.4.1.14823.2.3.1.11.1.2.1029
A Trap which indicates that a line card is inserted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSCInserted 1.3.6.1.4.1.14823.2.3.1.11.1.2.1030
a Trap which indicates that a supervisor card is inserted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNGBICInserted 1.3.6.1.4.1.14823.2.3.1.11.1.2.1031
A Trap which indicates that a GBIC is inserted in a Line Card.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNProcessDied 1.3.6.1.4.1.14823.2.3.1.11.1.2.1032
A Trap which indicates that a process has died.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNProcessExceedsMemoryLimits 1.3.6.1.4.1.14823.2.3.1.11.1.2.1033
A Trap which indicates that a process is consuming Large amounts of memory.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNLowOnFlashSpace 1.3.6.1.4.1.14823.2.3.1.11.1.2.1034
A Trap which indicates that the controller is running low on flash space.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNLowMemory 1.3.6.1.4.1.14823.2.3.1.11.1.2.1035
A Trap which indicates that the system free memory is low.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNFanTrayRemoved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1036
A Trap which indicates that a fan tray is removed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNFanTrayInserted 1.3.6.1.4.1.14823.2.3.1.11.1.2.1037
A Trap which indicates that a fan tray is inserted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNLCRemoved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1038
A Trap which indicates that a Line card is removed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNPowerSupplyMissing 1.3.6.1.4.1.14823.2.3.1.11.1.2.1039
A Trap which indicates that the power supply is missing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAccessPointIsUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1040
A Trap which indicates that an access point up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAccessPointIsDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1041
A Trap which indicates that an access point down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNCoverageHoleDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1042
This trap indicates that an access point at Location wlsxTrapAPLocation has detected a Coverage Hole.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNChannelChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1043
This trap indicates that an access point at Location wlsxTrapAPLocation has changed the channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNStationAddedToBlackList 1.3.6.1.4.1.14823.2.3.1.11.1.2.1044
This trap indicates that the station is black listed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNStationRemovedFromBlackList 1.3.6.1.4.1.14823.2.3.1.11.1.2.1045
This trap indicates that the station is removed from the black list.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNIpSpoofingDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1046
A trap indicating that the controller detected IP Spoofing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNDBCommunicationFailure 1.3.6.1.4.1.14823.2.3.1.11.1.2.1047
This trap indicates that communication with Database failed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNVrrpStateChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1048
This trap indicates that VRRP state has changed on the controller.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNRadioAttributesChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1049
A Trap which indicates changes in the Radio attributes of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNESIServerUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1050
A Trap which indicates that a ESI server is up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNESIServerDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1051
A Trap which indicates that a ESI server is down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNLicenseExpiry 1.3.6.1.4.1.14823.2.3.1.11.1.2.1052
A Trap which indicates that one or more licenses on the controller will expire in wlsxTrapLicenseDaysRemaining days.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxUnsecureAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1053
This trap indicates that an unauthorized access point is connected to the wired network. The access point is declared Rogue because it was matched to a MAC address.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxUnsecureAPResolved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1054
This trap indicates that a previously detected access point, classified as Rogue, is no longer present in the network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaImpersonation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1055
This trap indicates that an AM detected Station Impersonation.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxReservedChannelViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1056
This trap indicates that an AM detected an access point which is violating the Reserved Channel configuration.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxValidSSIDViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1057
This trap indicates that an AP has detected an access point is violating Valid SSID configuration by using an SSID that is reserved for use by a valid AP only.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1058
This trap indicates that an AP detected an access point that has a channel misconfiguration because it is using a channel that is not valid.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxOUIMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1059
This trap indicates that an AP detected an access point that has an OUI misconfiguration because it is using an OUI that is not valid.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSSIDMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1060
This trap indicates that an AP detected an access point that has an SSID misconfiguration because it is using an SSID that is not valid.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxShortPreableMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1061
This trap indicates that an access point has bad Short preamble configuration.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWPAMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1062
This trap indicates that an AP detected an access point that is misconfigured because it is not using WPA.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetworkDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1063
This trap indicates that an AM has detected an Ad hoc network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetworkRemoved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1064
This trap indicates that a previously detected Ad hoc Network is no longer present in the network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaPolicyViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1065
This trap indicates that Protection was enforced because a valid station's association to a non-valid access point violated Valid Station policy. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0019
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxRepeatWEPIVViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1066
This trap indicates that an AP detected that a valid access point is using the same WEP initialization vector in consecutive packets.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWeakWEPIVViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1067
This trap indicates that an AP detected that a valid access point is using a Weak WEP initialization vector. For more info check: http://www.wve.org/entries/show/WVE-2005-0021
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelInterferenceDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1068
This trap indicates that an AP has detected channel interference.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelInterferenceCleared 1.3.6.1.4.1.14823.2.3.1.11.1.2.1069
This trap indicates that a previously detected channel interference is no longer present.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPInterferenceDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1070
This trap indicates that an AP has detected interference for an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPInterferenceCleared 1.3.6.1.4.1.14823.2.3.1.11.1.2.1071
This trap indicates that the previously detected interference for an access point is no longer present.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaInterferenceDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1072
This trap indicates that an AP has detected interference for a station.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaInterferenceCleared 1.3.6.1.4.1.14823.2.3.1.11.1.2.1073
This trap indicates that the previously detected interference for a station is no longer present.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameRetryRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1074
This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Retry Rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameReceiveErrorRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1075
This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Receive Error Rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameFragmentationRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1076
This trap indicates that an AP detected that an access point exceeded the configured upper threshold for Frame Fragmentation Rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameBandWidthRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1077
This trap indicates that an AP detected that a station or access point has exceeded the configured upper threshold for Bandwidth rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameLowSpeedRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1078
This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Low speed rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFrameNonUnicastRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1079
This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Non Unicast traffic rate.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxLoadbalancingEnabled 1.3.6.1.4.1.14823.2.3.1.11.1.2.1080
This trap indicates that an AM is reporting that an AP has enabled Load balancing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxLoadbalancingDisabled 1.3.6.1.4.1.14823.2.3.1.11.1.2.1081
This trap indicates that an AM is reporting that an AP has enabled Load balancing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelFrameRetryRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1082
This trap indicates that an AP has detected that the configured upper threshold for Frame Retry Rate was exceeded on a channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelFrameFragmentationRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1083
This trap indicates that an AP has detected that the configured upper threshold for Frame Fragmentation Rate was exceeded on a channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelFrameErrorRateExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1084
This trap indicates that an AP has detected that the configured upper threshold for Frame Receive Error Rate was exceeded on a channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignatureMatchAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1085
This trap indicates that an AP detected a signature match in a frame from an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignatureMatchSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1086
This trap indicates that an AP detected a signature match in a frame from a Station.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChannelRateAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1087
This trap indicates that an AP detected frames on a channel which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNodeRateAnomalyAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1088
This trap indicates that an AP detected frames transmitted or received by an access point, which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNodeRateAnomalySta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1089
This trap indicates that an AP detected frames transmitted or received by a node, which exceed the configured IDS rate threshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxEAPRateAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1090
This trap indicates that the rate of EAP Handshake packets received by an AP has exceeded the configured IDS EAP Handshake rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0049
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignalAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1091
This trap indicates that an AM detected a Signal Anomaly.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSequenceNumberAnomalyAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1092
This trap indicates that an AM received packets from an AP which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSequenceNumberAnomalySta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1093
This trap indicates that an AM received packets from a Node which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxDisconnectStationAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1094
This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxApFloodAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1095
This trap indicates that the number of potential fake APs detected by an AP has exceeded the configured IDS threshold. This is the total number of fake APs observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetwork 1.3.6.1.4.1.14823.2.3.1.11.1.2.1096
This trap indicates that an AM detected an Ad hoc Network. An Station is connected to an ad hoc AP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWirelessBridge 1.3.6.1.4.1.14823.2.3.1.11.1.2.1097
This trap indicates that an AP detected a Wireless Bridge when a WDS frame was seen between the transmitter and receiver addresses.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInvalidMacOUIAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1098
This trap indicates that an AP detected an invalid MAC OUI in the BSSID of a frame. An invalid MAC OUI suggests that the frame may be spoofed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInvalidMacOUISta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1099
This trap indicates that an AP detected an invalid MAC OUI in the SRC or DST address of a frame. An invalid MAC OUI suggests that the frame may be spoofed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWEPMisconfiguration 1.3.6.1.4.1.14823.2.3.1.11.1.2.1100
This trap indicates that an AP detected an access point that is misconfigured because it does not have Privacy enabled.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaRepeatWEPIVViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1101
This trap indicates that an AP detected that a valid station is using the same WEP initialization vector in consecutive packets.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaWeakWEPIVViolation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1102
This trap indicates that an AP detected that a valid station is using a Weak WEP initialization vector.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaAssociatedToUnsecureAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1103
This trap indicates that an AM detected a client associated with a Rogue access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStaUnAssociatedFromUnsecureAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1104
This trap indicates that a previously detected rogue access point association is no longer present.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetworkBridgeDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1105
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInterferingApDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1106
This trap indicates that an AP detected an access point classified as Interfering. The access point is declared Interfering because it is neither authorized or classified as Rogue.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPortUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1107
This trap indicates that a Physical port is up.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPortDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1108
This trap indicates that a Physical port is Down.
Status: deprecated Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxBSSIDIsUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1109
A Trap which indicates that an access point BSSID is up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxBSSIDIsDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1110
A Trap which indicates that an access point BSSID is down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxColdStart 1.3.6.1.4.1.14823.2.3.1.11.1.2.1111
An enterprise version of cold start trap, which contains the controller time stamp.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWarmStart 1.3.6.1.4.1.14823.2.3.1.11.1.2.1112
An enterprise version of warm start trap, which contains the controller time stamp.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPImpersonation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1113
This trap indicates that an AP detected AP Impersonation because the number of beacons seen has exceeded the expected number by the configured percentage threshold. The expected number is calculated based on the Beacon Interval Field in the Beacon frame.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInformQueueOverFlow 1.3.6.1.4.1.14823.2.3.1.11.1.2.1114
This trap indicates that an Inform queue overflow condition occurred.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthServerIsDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1115
This trap indicates that an authentication server is down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCTSTransferError 1.3.6.1.4.1.14823.2.3.1.11.1.2.1116
This trap indicates the status of the configuration transfer from the management station.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCTSTransferSucceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1117
This trap indicates the status of the configuration transfer from the management station.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxConfigurationUpdateError 1.3.6.1.4.1.14823.2.3.1.11.1.2.1118
This trap indicates the configuration update status.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxConfigurationUpdateSucceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1119
This trap indicates the configuration update status.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxGlobalConfigurationChangeNotification 1.3.6.1.4.1.14823.2.3.1.11.1.2.1120
This trap indicates that global configuration was modified on the controller.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxUserEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1121
This trap indicates that the user configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPBssidEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1122
This trap indicates that the BSSID configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPRadioEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1123
This trap indicates that the Radio configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1124
This trap indicates that the AP configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSwitchListEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1125
This trap indicates that the controller list has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPortEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1126
This trap indicates that the port configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxVlanEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1127
This trap indicates that the VLAN configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxVlanInterfaceEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1128
This trap indicates that the VLAN Interface configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWindowsBridgeDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1129
This trap indicates that an AM has detected a station that is bridging from a wireless network to a wired network
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxLicenseEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1130
This trap indicates that the license table has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxEsiServerChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1131
This trap indicates that the ESI server table has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMonAPEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1132
This trap indicates that a monitored AP entry changed
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMonStationEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1133
This trap indicates that a monitored station entry changed
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignAPNetstumbler 1.3.6.1.4.1.14823.2.3.1.11.1.2.1134
This trap indicates that an AP detected a signature match for Netstumbler from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignStaNetstumbler 1.3.6.1.4.1.14823.2.3.1.11.1.2.1135
This trap indicates that an AP detected a signature match for Netstumbler from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignAPAsleap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1136
This trap indicates that an AP detected a signature match for ASLEAP from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignStaAsleap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1137
This trap indicates that an AP detected a signature match for ASLEAP from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignAPAirjack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1138
This trap indicates that an AP detected a signature match for AirJack from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignStaAirjack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1139
This trap indicates that an AP detected a signature match for AirJack from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignAPNullProbeResp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1140
This trap indicates that an AP detected a signature match for Null-Probe-Response from an access point. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignStaNullProbeResp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1141
This trap indicates that an AP detected a signature match for Null-Probe-Response from a Station. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignAPDeauthBcast 1.3.6.1.4.1.14823.2.3.1.11.1.2.1142
This trap indicates that an AP detected a signature match for Deauth-Broadcast from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSignStaDeauthBcast 1.3.6.1.4.1.14823.2.3.1.11.1.2.1143
This trap indicates that an AP detected a signature match for Deauth-Broadcast from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWindowsBridgeDetectedAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1144
This trap indicates that an AP is detecting an access point that is bridging from a wireless network to a wired network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWindowsBridgeDetectedSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1145
This trap indicates that an AP is detecting a station that is bridging from a wireless network to a wired network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetworkBridgeDetectedAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1146
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocNetworkBridgeDetectedSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1147
This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxDisconnectStationAttackAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1148
This trap indicates that an AM detected a station disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxDisconnectStationAttackSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1149
This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSuspectUnsecureAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1150
This trap indicates that an access point, classified as Suspected Rogue, has been detected by a Controller. The AP is suspected to be rogue, with the supplied confidence level, because it was matched to the wired MAC address.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxSuspectUnsecureAPResolved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1151
This trap indicates that a previously detected access point, classified Suspected Rogue, is either no longer present in the network or has changed its state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxConfigurationLicenseMismatch 1.3.6.1.4.1.14823.2.3.1.11.1.2.1152
This trap indicates the configuration update status in the case where some configuration could not be applied due to missing licenses.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxVoiceCdrBufferThresholdReached 1.3.6.1.4.1.14823.2.3.1.11.1.2.1153
This trap indicates that the CDR buffer threshold has been reached
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxTunnelUp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1154
This trap indicates that a tunnel interface is up.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxTunnelDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1155
This trap indicates that a tunnel interface is down.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMeshNodeEntryChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1156
This trap indicates that the mesh node configuration has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxHtGreenfieldSupported 1.3.6.1.4.1.14823.2.3.1.11.1.2.1157
This trap indicates that an AP detected an access point that supports HT Greenfield mode. For more info check: http://www.wve.org/entries/show/WVE-2008-0005
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxHT40MHzIntoleranceAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1158
This trap indicates that an AP is detecting an access point with the HT 40MHz intolerance setting. For more info check: http://www.wve.org/entries/show/WVE-2008-0004
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxHT40MHzIntoleranceSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1159
This trap indicates that the system is detecting an HT 40MHz Intolerance setting from a Station. For more info check: http://www.wve.org/entries/show/WVE-2008-0004
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthServerAllInService 1.3.6.1.4.1.14823.2.3.1.11.1.2.1160
This trap indicates that all authentication servers is a server group are brought back in service.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAdhocNetwork 1.3.6.1.4.1.14823.2.3.1.11.1.2.1161
This trap indicates that an AP detected an ad hoc network where a station is connected to an ad hoc access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAdhocNetworkBridgeDetectedAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1162
This trap indicates that an AP detected an ad hoc network that is bridging to a wired network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAdhocNetworkBridgeDetectedSta 1.3.6.1.4.1.14823.2.3.1.11.1.2.1163
This trap indicates that an AP detected an ad hoc network that is bridging to a wired network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAuthMaxXsecUserEntries 1.3.6.1.4.1.14823.2.3.1.11.1.2.1164
A trap which indicates that the xSec user limit is reached.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNVpnMaxSessions 1.3.6.1.4.1.14823.2.3.1.11.1.2.1165
A trap which indicates that the VPN session limit is reached.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNRapExpiredPSK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1166
A trap which indicates that the RAP is using the Expired PSK.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNRapWarnExpiredPSK 1.3.6.1.4.1.14823.2.3.1.11.1.2.1167
A trap which indicates that the Cached IKE PSK for RAPs will expire soon.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNConnectionResetWithLocal 1.3.6.1.4.1.14823.2.3.1.11.1.2.1168
A trap which indicates that tcp connection between master controller and local controller has been lost.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNApOnBackupController 1.3.6.1.4.1.14823.2.3.1.11.1.2.1169
A trap which indicates that the AP has registered with the backup controller.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientFloodAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1170
This trap indicates that the number of potential fake clients detected by an AP has exceeded the configured IDS threshold. This is the total number of fake clients observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxValidClientNotUsingEncryption 1.3.6.1.4.1.14823.2.3.1.11.1.2.1171
This trap indicates that an AP detected an unencrypted data frame between a valid client and an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAdhocUsingValidSSID 1.3.6.1.4.1.14823.2.3.1.11.1.2.1172
This trap indicates that an AP detected an ad hoc network using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPSpoofingDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1173
This trap indicates that an AP detected that one of its virtual APs is being spoofed using MAC spoofing. For more info check: http://www.wve.org/entries/show/WVE-2005-0019
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientAssociatingOnWrongChannel 1.3.6.1.4.1.14823.2.3.1.11.1.2.1174
This trap indicates that an AP detected a client trying to associate to one of its BSSIDs on the wrong channel. This can be a sign that the BSSID is being spoofed in order to fool the client into thinking the AP is operating on another channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNDisconnectStationAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1175
This trap indicates that an AP has determined that a client is under Disconnect Attack because the rate of Assoc/Reassoc Response packets received by that client exceeds the configured threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNStaUnAssociatedFromUnsecureAP 1.3.6.1.4.1.14823.2.3.1.11.1.2.1176
This trap indicates that an AP that had previously detected a client association to a Rogue access point is no longer detecting that association.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxOmertaAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1177
This trap indicates that an AP detected an Omerta attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0053
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxTKIPReplayAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1178
This trap indicates that an AP detected a possible TKIP replay attack. If successful this could be the precursor to more advanced attacks. For more info check: http://www.wve.org/entries/show/WVE-2008-0013
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxChopChopAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1179
This trap indicates that an AP detected a ChopChop attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0038
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFataJackAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1180
This trap indicates that an AP detected a FATA-Jack attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0057
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxInvalidAddressCombination 1.3.6.1.4.1.14823.2.3.1.11.1.2.1181
This trap indicates that an AP detected an invalid source and destination combination. For more info check: http://www.wve.org/entries/show/WVE-2008-0011
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxValidClientMisassociation 1.3.6.1.4.1.14823.2.3.1.11.1.2.1182
This trap indicates that an AP detected a misassociation between a valid client and an unsafe AP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMalformedHTIEDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1183
This trap indicates that an AP detected a malformed HT Information Element. This can be the result of a misbehaving wireless driver or it may be an indication of a new wireless attack.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMalformedAssocReqDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1184
This trap indicates that an AP detected a malformed association request with a NULL SSID. For more info check: http://www.wve.org/entries/show/WVE-2008-0010
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxOverflowIEDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1185
This trap indicates that an AP detected a management frame with a malformed information element. The declared length of the element is larger than the entire frame containing the element. This may be used to corrupt or crash wireless drivers. For more info check: http://www.wve.org/entries/show/WVE-2008-0008
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxOverflowEAPOLKeyDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1186
This trap indicates that an AP detected a key in an EAPOL Key message with a specified length greater than the length of the entire message. For more info check: http://www.wve.org/entries/show/WVE-2008-0009
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMalformedFrameLargeDurationDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1187
This trap indicates that an AP detected an unusually large duration in a wireless frame. This may be an attempt to block other devices from transmitting. For more info check: http://www.wve.org/entries/show/WVE-2005-0051
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMalformedFrameWrongChannelDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1188
This trap indicates that an AP detected a beacon on one channel advertising another channel. This could be an attempt to lure clients away from a valid AP. For more info check: http://www.wve.org/entries/show/WVE-2006-0050
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMalformedAuthFrame 1.3.6.1.4.1.14823.2.3.1.11.1.2.1189
This trap indicates that an AP detected an authentication frame with either a bad algorithm (similar to Fata-Jack) or a bad transaction. For more info check: http://www.wve.org/entries/show/WVE-2006-0057
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCTSRateAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1190
This trap indicates that the rate of CTS packets received by an AP exceeds the configured IDS threshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxRTSRateAnomaly 1.3.6.1.4.1.14823.2.3.1.11.1.2.1191
This trap indicates that the rate of RTS packets received by an AP exceeds the configured IDS threshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNRogueAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1192
This trap indicates that an unauthorized access point is connected to the wired network. The access point is classified as Rogue by the system.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNRogueAPResolved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1193
This trap indicates that a previously detected access point, classified as Rogue, is either no longer present in the network or it changed its state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNeighborAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1194
This trap indicates that an access point has been classified as a Neighbor by the system.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNInterferingAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1195
This trap indicates that an access point has been classified as Interfering by the system. The access point is declared Interfering because it is not authorized, nor has it been classified as a Rogue.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSuspectRogueAPDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1196
This trap indicates that an access point, classified as Suspected Rogue, is detected by the system. The AP is suspected to be rogue with the supplied confidence level.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSuspectRogueAPResolved 1.3.6.1.4.1.14823.2.3.1.11.1.2.1197
This trap indicates that a previously detected access point, classified as Suspected Rogue, is either no longer present in the network or has changed its state.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxBlockAckAttackDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1198
This trap indicates that an attempt has been made to deny service to the source address by spoofing a block ACK add request that sets a sequence number window outside the currently used window. For more info check: http://www.wve.org/entries/show/WVE-2008-0006
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxHotspotterAttackDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1199
This trap indicates that a new AP has appeared immediately following a client probe request. This is indicative of the Hotspotter tool or similar that attempts to trap clients with a fake hotspot or other wireless network. For more info check: http://www.wve.org/entries/show/WVE-2005-0054
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatch 1.3.6.1.4.1.14823.2.3.1.11.1.2.1200
This trap indicates that an AP detected a signature match in a frame.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchNetstumbler 1.3.6.1.4.1.14823.2.3.1.11.1.2.1201
This trap indicates that an AP detected a signature match for Netstumbler in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0025
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchAsleap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1202
This trap indicates that an AP detected a signature match for ASLEAP in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0027
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchAirjack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1203
This trap indicates that an AP detected a signature match for Airjack in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0018
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchNullProbeResp 1.3.6.1.4.1.14823.2.3.1.11.1.2.1204
This trap indicates that an AP detected a signature match for Null-Probe-Response in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0064
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchDeauthBcast 1.3.6.1.4.1.14823.2.3.1.11.1.2.1205
This trap indicates that an AP detected a signature match for Deauth-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchDisassocBcast 1.3.6.1.4.1.14823.2.3.1.11.1.2.1206
This trap indicates that an AP detected a signature match for Disassoc-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0046
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNSignatureMatchWellenreiter 1.3.6.1.4.1.14823.2.3.1.11.1.2.1207
This trap indicates that an AP detected a signature match for Wellenreiter in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0058
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPDeauthContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1208
This trap indicates that an AP has attempted to contain an access point by disconnecting its client.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientDeauthContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1209
This trap indicates that an AP has attempted to contain a client by disconnecting it from the AP that it is associated with.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPWiredContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1210
This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientWiredContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1211
This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPTaggedWiredContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1212
This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientTaggedWiredContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1213
This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxTarpitContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1214
This trap indicates that an AP has attempted to contain an access point by moving a client that is attempting to associate to it to a tarpit.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxVoiceClientLocationUpdate 1.3.6.1.4.1.14823.2.3.1.11.1.2.1215
This trap indicates that the location of voice client has been changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPChannelChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1216
This trap indicates that an AP changed its channel.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPPowerChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1217
This trap indicates that an AP changed its transmit power level.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPModeChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1218
This trap indicates that an AP changed its mode from AP to APMonitor or vice versa.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxUserEntryAttributesChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1219
This trap indicates that the user entry attributes have changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPowerSaveDosAttack 1.3.6.1.4.1.14823.2.3.1.11.1.2.1220
This trap indicates that an AP detected a Power Save DoS attack.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAPMasterStatusChange 1.3.6.1.4.1.14823.2.3.1.11.1.2.1221
This trap indicates that the status of the AP as seen by the master controller has changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNAdhocUsingValidSSID 1.3.6.1.4.1.14823.2.3.1.11.1.2.1222
This trap indicates that an AP detected an ad hoc network node using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCRLExpired 1.3.6.1.4.1.14823.2.3.1.11.1.2.1223
This trap indicates that the CRL associated with the particular Trustpoint is expired.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxMgmtUserAuthenticationFailed 1.3.6.1.4.1.14823.2.3.1.11.1.2.1224
This trap indicates that a management user authentication has failed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNConnectionBackfromLocal 1.3.6.1.4.1.14823.2.3.1.11.1.2.1225
A trap which indicates that tcp connection between master controller and local controller is back.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPNumUpgradeFailure 1.3.6.1.4.1.14823.2.3.1.11.1.2.1226
A trap which indicates the number of upgrade failure of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPNumWarmStarts 1.3.6.1.4.1.14823.2.3.1.11.1.2.1227
A trap which indicates the number of warm starts of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPNumColdStarts 1.3.6.1.4.1.14823.2.3.1.11.1.2.1228
A trap which indicates the number of cold starts of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPNumDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1229
A trap which indicates the number of down alarms of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPNumRadioDown 1.3.6.1.4.1.14823.2.3.1.11.1.2.1230
A trap which indicates the number of radio down alarms of an access point.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNumClockSyncErrors 1.3.6.1.4.1.14823.2.3.1.11.1.2.1231
A trap which indicates the total number of clock sync errors between the switch and access points.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNumColdStart 1.3.6.1.4.1.14823.2.3.1.11.1.2.1232
A trap which indicates the number of cold-starts of the switch.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxNumWarmStart 1.3.6.1.4.1.14823.2.3.1.11.1.2.1233
A trap which indicates the number of warm-starts of the switch.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWirelessHostedNetworkDetected 1.3.6.1.4.1.14823.2.3.1.11.1.2.1234
This trap indicates that an AP detected a wireless client that is hosting a softAP. The softAP could be used to share the hosting client's wired or wireless network connection with other wireless users.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxClientAssociatedToHostedNetwork 1.3.6.1.4.1.14823.2.3.1.11.1.2.1235
This trap indicates that an AP detected that a wireless client associated to an access point that is hosted by another wireless client.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxThresholdExceeded 1.3.6.1.4.1.14823.2.3.1.11.1.2.1236
A trap indicates a particular resource under monitoring has gone above the threshold specified.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxThresholdCleared 1.3.6.1.4.1.14823.2.3.1.11.1.2.1237
A trap indicates a particular resource under monitoring has come below the threshold specified.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWirelessHostedNetworkContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1238
This trap indicates that containment is being enforced on a client associated to a hosted network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxHostOfWirelessNetworkContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1239
This trap indicates that containment is being enforced on a client that is hosting a wireless hosted network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxEnhancedAdhocContainment 1.3.6.1.4.1.14823.2.3.1.11.1.2.1240
This trap indicates that an AP has attempted to contain an adhoc node by disconnecting it from other members of the adhoc network.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPowerSupplyOKTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1241
This trap indicates that the system power supply condition have returned to normal operation status.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPowerSupplyFailureTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1242
A trap which indicates that the power supply has failed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFanTrayRemovedTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1243
A Trap which indicates that a fan tray is removed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxFanTrayInsertedTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1244
A Trap which indicates that a fan tray is inserted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxPowerSupplyMissingTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1245
A Trap which indicates that the power supply is missing.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStackTopologyChangeTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1246
When change happens in any topology of the stack element in the stack, then a notification is sent to the Management Entity.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxStackIfStateChangeTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1247
When any stacking interface in any stack element joins or leaves stacking topology, then a notification is sent to the Management Entity with slot and interface information.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxLicenseServerExpiry 1.3.6.1.4.1.14823.2.3.1.11.1.2.1248
A Trap which indicates that licenses sent from the license server will expire in wlsxTrapLicenseServerDaysRemaining days.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxLicenseClientExpiry 1.3.6.1.4.1.14823.2.3.1.11.1.2.1249
A Trap which indicates that licenses contributed by a license client will expire in wlsxTrapLicenseClientDaysRemaining days.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxIfStateChangeTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1250
When the link state of an interface changes due to reason specified by wlsxIfStateChangeReason object, a notification is sent to the Management Entity with reason for this state change and interface information.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxWMSOffloadRecommended 1.3.6.1.4.1.14823.2.3.1.11.1.2.1251
This trap indicates that current state in the WMS module shows that WMS is reaching capacity, and so it is recommended to enable WMS-Offload.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPActiveUplinkChanged 1.3.6.1.4.1.14823.2.3.1.11.1.2.1252
When the active uplink of an AP changes, a notification is sent to the Management Entity with the new uplink type
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCertExpiringSoon 1.3.6.1.4.1.14823.2.3.1.11.1.2.1253
This trap indicates that a particular Certificate is going to expire in less than 60 days.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxCertExpired 1.3.6.1.4.1.14823.2.3.1.11.1.2.1254
This trap indicates that a particular Certificate has expired and is no longer valid.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

wlsxAPManagedModeConfigFailureTrap 1.3.6.1.4.1.14823.2.3.1.11.1.2.1255
This trap indicates that config apply has failed on the IAP.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor