WS-SW-IGMP-SNOOP-MIB

File: WS-SW-IGMP-SNOOP-MIB.mib (15762 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
WS-SW-SMI

Imported symbols

OBJECT-GROUP MODULE-COMPLIANCE IpAddress
Integer32 OBJECT-TYPE MODULE-IDENTITY
TruthValue wsSwIgmpSnoop

Defined Types

WsSwIgmpSnoopVlanConfigEntry  
SEQUENCE    
  wsSwIgmpSnoopVlanIndex Integer32
  wsSwIgmpSnoopEnable TruthValue
  wsSwIgmpSnoopUnknownMcastFwd TruthValue
  wsSwIgmpSnoopLearningMode INTEGER
  wsSwIgmpSnoopMrouterSetStaticPort OCTET STRING

WsSwIgmpSnoopQuerierEntry  
SEQUENCE    
  wsSwIgmpSnoopQuerierVlanIndex Integer32
  wsSwIgmpSnoopQuerierEnable TruthValue
  wsSwIgmpSnoopQuerierVersion INTEGER
  wsSwIgmpSnoopQuerierMaxResponseTime INTEGER
  wsSwIgmpSnoopQuerierPresentTimeout INTEGER
  wsSwIgmpSnoopQuerierIPAddress IpAddress
  wsSwIgmpSnoopQuerierOperationalState INTEGER

Defined Values

wsSwIgmpSnoopMibModule 1.3.6.1.4.1.388.14.2.17.1
IGMP SNOOP MIB module defines the configuration parameters for the IGMP Snoop feature which is used to optimize the multicast traffic using IGMP protocol.
MODULE-IDENTITY    

wsSwIgmpSnoopMIB 1.3.6.1.4.1.388.14.2.17.1.1
OBJECT IDENTIFIER    

wsSwIgmpSnoopScalars 1.3.6.1.4.1.388.14.2.17.1.1.1
OBJECT IDENTIFIER    

wsSwIgmpSnoopEnableDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.1
By Default IGMP Snooping is enabled. The default value is TRUE.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopUnknownMcastFwdDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.2
This configures the default behaviour for unknown multicast forward for all Vlans. Enabling unknown multicast packets will cause flooding of multicast packets which fall outside the range of 224.0.0.X and have not been joined by any host. Disabling will cause forwarding of such packets only to multicast router ports. The default value is FALSE.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopQuerierEnableDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.3
Enable/Disable IGMP Snooping Querier at global level. The default value is disabled(FALSE).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopQuerierVersionDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.4
The default IGMP Version for the queries to be generated by the querier. The default value is igmpv3(3) version.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER igmpv1(1), igmpv2(2), igmpv3(3)  

wsSwIgmpSnoopQuerierMaxResponseTimeDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.5
The default IGMP Querier maximum response time used in building IGMP V2/V3 queries, indicating the maximum time in seconds in which the interested hosts should respond back with a report. The default value is 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..25  

wsSwIgmpSnoopQuerierPresentTimeoutDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.6
The default timeout value for the external IGMP querier connected to the switch. This value is used to start of the local Querier to send the locally generated IGMP query based on the Querier configuration when ever the Multicast router goes away and a Query loss is detected. The default value is 60 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..300  

wsSwIgmpSnoopQuerierQueryIntervalDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.7
The default query interval which will be used by the IGMP querier to build and send the locally generated IGMP queries periodically. The configured query interval will be common across all VLAN. The default value is 60 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..18000  

wsSwIgmpSnoopQuerierIPAddressDefault 1.3.6.1.4.1.388.14.2.17.1.1.1.8
The Default source IP Address used by the querier as source IP while generating the IGMP queries. The default value is 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wsSwIgmpSnoopVlanConfigTable 1.3.6.1.4.1.388.14.2.17.1.1.2
Configures IGMP Snooping configuration per Vlan. User can provide static multicast router ports for each vlan and needs to configure the learning mode to be static in case he is configuring static entries else write will fail.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwIgmpSnoopVlanConfigEntry

wsSwIgmpSnoopVlanConfigEntry 1.3.6.1.4.1.388.14.2.17.1.1.2.1
An entry in wsSwIgmpSnoopingVlanConfigTable
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwIgmpSnoopVlanConfigEntry  

wsSwIgmpSnoopVlanIndex 1.3.6.1.4.1.388.14.2.17.1.1.2.1.1
The Index for the current table and is the actual VLAN's configured on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4094  

wsSwIgmpSnoopEnable 1.3.6.1.4.1.388.14.2.17.1.1.2.1.2
Enable/Disable IGMP Snooping on this Vlan. By Default IGMP Snooping is enabled. The default value is TRUE.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopUnknownMcastFwd 1.3.6.1.4.1.388.14.2.17.1.1.2.1.3
Enabling unknown multicast packets will cause flooding of multicast packets which fall outside the range of 224.0.0.X and have not been joined by any host. Disabling will cause forwarding of such packets only to multicast router ports. The Default value if False.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopLearningMode 1.3.6.1.4.1.388.14.2.17.1.1.2.1.4
This object specifies the multicast router port learning method for IGMP Snooping as described below: pimDvmrp(1) : Protocol Independent Multicast and Distance Vector static(2) : Static entry The Default value is pimDvmrp(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pimDvmrp(1), static(2)  

wsSwIgmpSnoopMrouterSetStaticPort 1.3.6.1.4.1.388.14.2.17.1.1.2.1.5
In case if the learning of multicast router ports is static then one can do a set operation over this OID to configure the set of physical ports for this vlan where the Multicast routers are connected. If learn mode is pim-dvmrp the set over this OID will give a commit fail as an error condition. For multiple ports to be configured user can give comma separated port names Eg. ge1,ge3.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wsSwIgmpSnoopQuerierTable 1.3.6.1.4.1.388.14.2.17.1.1.3
This table provides the configuration for the IGMP Querier which is used to send out the IGMP general queries locally in the absence of any external Querier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwIgmpSnoopQuerierEntry

wsSwIgmpSnoopQuerierEntry 1.3.6.1.4.1.388.14.2.17.1.1.3.1
An entry in the wsSwIgmpSnoopQuerierTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwIgmpSnoopQuerierEntry  

wsSwIgmpSnoopQuerierVlanIndex 1.3.6.1.4.1.388.14.2.17.1.1.3.1.1
The Index for the current table and is the actual VLAN's configured on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4094  

wsSwIgmpSnoopQuerierEnable 1.3.6.1.4.1.388.14.2.17.1.1.3.1.2
Enable/Disable IGMP Snooping Querier on this Vlan. By Default IGMP Snooping Querier is disabled. The default value is FALSE.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwIgmpSnoopQuerierVersion 1.3.6.1.4.1.388.14.2.17.1.1.3.1.3
The IGMP Version for the queries to be generated by the querier. The Default value is igmpv3(3) version.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER igmpv1(1), igmpv2(2), igmpv3(3)  

wsSwIgmpSnoopQuerierMaxResponseTime 1.3.6.1.4.1.388.14.2.17.1.1.3.1.4
The IGMP Querier maximum response time used in building IGMP V2/V3 queries, indicating the maximum time in seconds in which the interested hosts should resond back with a report.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

wsSwIgmpSnoopQuerierPresentTimeout 1.3.6.1.4.1.388.14.2.17.1.1.3.1.5
The timeout value for the external IGMP querier connected to the switch. This value is used to start of the local Querier to send the locally generated IGMP query based on the Querier configuration when ever the Multicast router goes away and a Query loss is detected.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..300  

wsSwIgmpSnoopQuerierIPAddress 1.3.6.1.4.1.388.14.2.17.1.1.3.1.6
The source IP Address used by the querier while generating the IGMP queries. By default this is zero. If the querier is enabled and it's IP address is not configured then switch will try to the following IP address in the given prefrence: 1. Use the Querier global default IP address. 2. use the corresponding SVI IP. 3. Try to use the first occurring IP address among all the interfaces. If none of the above has been configured for an IP address then it will not send send out the query.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wsSwIgmpSnoopQuerierOperationalState 1.3.6.1.4.1.388.14.2.17.1.1.3.1.7
This OID shows the operational status of the Querier. The Querier goes to non-querier state when ever wireless switch detects a query coming from a Multicast router or any other querier from an external network. In the absence of a multicast router or a query loss is detected and if the IGMP Querier is enabled globally and on this vlan then it will move to querier state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER querier(1), nonquerier(2), disabled(3)  

wsSwIgmpSnoopConf 1.3.6.1.4.1.388.14.2.17.1.1.20
OBJECT IDENTIFIER    

wsSwIgmpSnoopGroups 1.3.6.1.4.1.388.14.2.17.1.1.20.1
OBJECT IDENTIFIER    

wsSwIgmpSnoopObjectGroup 1.3.6.1.4.1.388.14.2.17.1.1.20.1.1
Description.
Status: current Access: read-only
OBJECT-GROUP    

wsSwIgmpSnoopCompliances 1.3.6.1.4.1.388.14.2.17.1.1.20.2
OBJECT IDENTIFIER    

wsSwIgmpSnoopCompliance 1.3.6.1.4.1.388.14.2.17.1.1.20.2.1
Description.
Status: current Access: read-only
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor