WWP-LEOS-PORT-MIB

File: WWP-LEOS-PORT-MIB.mib (56001 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	RFC1213-MIB
WWP-SMI	IEEE8023-LAG-MIB

Imported symbols

Integer32	Unsigned32	Counter32
Gauge32	TimeTicks	OBJECT-TYPE
NOTIFICATION-TYPE	MODULE-IDENTITY	DisplayString
MacAddress	TEXTUAL-CONVENTION	TruthValue
RowStatus	sysName	sysLocation
wwpModules	wwpModulesLeos	dot3adAggPortActorAdminKey
dot3adAggPortListPorts

Defined Types

PortList
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..255)

PortEgressFrameCosPolicy
Egress cos policy to use on this port ignore means leave egress map disabled
TEXTUAL-CONVENTION
	INTEGER	ingore(1), rcosToL2OuterPcpMap(2)

PortIngressFixedColor
Egress cos policy to use on this port ignore means leave egress map disabled
TEXTUAL-CONVENTION
	INTEGER	green(1), yellow(2)

WwpLeosEtherPortEntry
SEQUENCE
	wwpLeosEtherPortId	INTEGER
	wwpLeosEtherPortName	DisplayString
	wwpLeosEtherPortDesc	DisplayString
	wwpLeosEtherPortType	INTEGER
	wwpLeosEtherPortPhysAddr	MacAddress
	wwpLeosEtherPortAutoNeg	TruthValue
	wwpLeosEtherPortAdminStatus	INTEGER
	wwpLeosEtherPortOperStatus	INTEGER
	wwpLeosEtherPortAdminSpeed	INTEGER
	wwpLeosEtherPortOperSpeed	INTEGER
	wwpLeosEtherPortAdminDuplex	INTEGER
	wwpLeosEtherPortOperDuplex	INTEGER
	wwpLeosEtherPortAdminFlowCtrl	INTEGER
	wwpLeosEtherPortOperFlowCtrl	INTEGER
	wwpLeosEtherIngressPvid	INTEGER
	wwpLeosEtherUntagEgressVlanId	INTEGER
	wwpLeosEtherPortAcceptableFrameTypes	INTEGER
	wwpLeosEtherPortUntaggedPriority	INTEGER
	wwpLeosEtherPortMaxFrameSize	INTEGER
	wwpLeosEtherPortVlanIngressFiltering	TruthValue
	wwpLeosEtherPortAdminAdvertisedFlowCtrl	INTEGER
	wwpLeosEtherPortVplsPortType	INTEGER
	wwpLeosEtherPortIngressCosPolicy	INTEGER
	wwpLeosEtherPortIngressFixedDot1dPri	INTEGER
	wwpLeosEtherPortUntagDataVsi	INTEGER
	wwpLeosEtherPortOperationalSpeed	Gauge32
	wwpLeosEtherPortUntagCtrlVsi	INTEGER
	wwpLeosEtherPortMirrorPort	TruthValue
	wwpLeosEtherPortMirrorEncap	INTEGER
	wwpLeosEtherPortMirrorEncapVid	INTEGER
	wwpLeosEtherPortMirrorEncapTpid	INTEGER
	wwpLeosEtherPortMirrorIngress	INTEGER
	wwpLeosEtherPortMirrorEgress	INTEGER
	wwpLeosEtherPortUntagDataVsiType	INTEGER
	wwpLeosEtherPortUntagCtrlVsiType	INTEGER
	wwpLeosEtherPortVsIngressFiltering	TruthValue
	wwpLeosEtherPortOperAutoNeg	INTEGER
	wwpLeosEtherPortUpTime	TimeTicks
	wwpLeosEtherPortUntagDataVid	INTEGER
	wwpLeosEtherPortPhyLoopback	TruthValue
	wwpLeosEtherPortVlanIngressFilterStrict	TruthValue
	wwpLeosEtherPortMacSaDaSwap	TruthValue
	wwpLeosEtherPortMacSaDaSwapVlan	INTEGER
	wwpLeosEtherPortResolvedCosPolicy	INTEGER
	wwpLeosEtherPortMode	INTEGER
	wwpLeosEtherFixedRcos	INTEGER
	wwpLeosEtherPortEgressPortQueueMapId	INTEGER
	wwpLeosEtherPortResolvedCosMapId	INTEGER
	wwpLeosEtherPortResolvedCosRemarkL2	TruthValue
	wwpLeosEtherPortL2TransformMode	INTEGER
	wwpLeosEtherPortLinkFlapDetection	TruthValue
	wwpLeosEtherPortLinkFlapCount	INTEGER
	wwpLeosEtherPortLinkFlapDetectTime	INTEGER
	wwpLeosEtherPortLinkFlapHoldTime	INTEGER
	wwpLeosEtherFixedRColor	PortIngressFixedColor
	wwpLeosEtherPortFrameCosMapId	INTEGER
	wwpLeosEtherPortEgressCosPolicy	PortEgressFrameCosPolicy
	wwpLeosEtherPortEgressSpeed	Gauge32
	wwpLeosEtherPortAdaptiveRateSpeed	Gauge32
	wwpLeosEtherPortIfgDecrease	Integer32
	wwpLeosEtherPortAdvertSpeed	INTEGER
	wwpLeosEtherPortAdvertDuplex	INTEGER

WwpLeosEtherPortFlushEntry
SEQUENCE
	wwpLeosEtherPortFlushActivate	TruthValue

WwpLeosEtherPortTrapsEntry
SEQUENCE
	wwpLeosEtherPortTrapsState	INTEGER

WwpLeosEtherPortStateMirrorGroupEntry
SEQUENCE
	wwpLeosEtherPortStateMirrorGroupId	INTEGER
	wwpLeosEtherPortStateMirrorGroupName	DisplayString
	wwpLeosEtherPortStateMirrorGroupOperStatus	INTEGER
	wwpLeosEtherPortStateMirrorGroupNumSrcPorts	Counter32
	wwpLeosEtherPortStateMirrorGroupNumDstPorts	Counter32
	wwpLeosEtherPortStateMirrorGroupOperStatus	INTEGER
	wwpLeosEtherPortStateMirrorGroupStatus	RowStatus
	wwpLeosEtherPortStateMirrorGroupType	INTEGER

WwpLeosEtherPortStateMirrorGroupMemEntry
SEQUENCE
	wwpLeosEtherPortStateMirrorGroupMemType	INTEGER
	wwpLeosEtherPortStateMirrorGroupMemOperState	INTEGER
	wwpLeosEtherPortStateMirrorGroupMemStatus	RowStatus

Defined Values

wwpLeosPortMIB		1.3.6.1.4.1.6141.2.60.2
This MIB defines the managed objects for Ethernet ports.
MODULE-IDENTITY

wwpLeosPortMIBObjects		1.3.6.1.4.1.6141.2.60.2.1
OBJECT IDENTIFIER

wwpLeosEtherPort		1.3.6.1.4.1.6141.2.60.2.1.1
OBJECT IDENTIFIER

wwpLeosEtherPortNotif		1.3.6.1.4.1.6141.2.60.2.1.2
OBJECT IDENTIFIER

wwpLeosPortMIBNotificationPrefix		1.3.6.1.4.1.6141.2.60.2.2
OBJECT IDENTIFIER

wwpLeosPortMIBNotifications		1.3.6.1.4.1.6141.2.60.2.2.0
OBJECT IDENTIFIER

wwpLeosPortMIBConformance		1.3.6.1.4.1.6141.2.60.2.3
OBJECT IDENTIFIER

wwpLeosPortMIBCompliances		1.3.6.1.4.1.6141.2.60.2.3.1
OBJECT IDENTIFIER

wwpLeosPortMIBGroups		1.3.6.1.4.1.6141.2.60.2.3.2
OBJECT IDENTIFIER

wwpLeosEtherPortTable		1.3.6.1.4.1.6141.2.60.2.1.1.1
Table of Ethernet Ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WwpLeosEtherPortEntry

wwpLeosEtherPortEntry		1.3.6.1.4.1.6141.2.60.2.1.1.1.1
Port Entry in the Ethernet Port Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	WwpLeosEtherPortEntry

wwpLeosEtherPortId		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.1
Port ID for the instance. Port ID's start at 1, and may not be consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

wwpLeosEtherPortName		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.2
A textual string containing information about the port. This string should indicate about the physical location of the port as well.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

wwpLeosEtherPortDesc		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.3
A textual string containing port description.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

wwpLeosEtherPortType		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.4
The port type for the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ethernet(1), fastEthernet(2), hundredFx(3), gigEthernet(4), lagPort(5), unknown(6), gigHundredFx(7), tripleSpeed(8), tenGigEthernet(9), gigTenGigEthernet(10)

wwpLeosEtherPortPhysAddr		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.5
The ethernet MAC address for the port. This information can also be achieved via dot1dTpFdbTable
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

wwpLeosEtherPortAutoNeg		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.6
The object sets the port to AUTO NEG MOde and vice versa. Specific platforms may have requirements of configuring speed before moving the port to out of AUTO-NEG mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortAdminStatus		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.7
The desired state of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

wwpLeosEtherPortOperStatus		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.8
The current operational state of Port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), notauth(3), lbtx(4), lbrx(5), linkflap(6)

wwpLeosEtherPortAdminSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.9
Desired speed of the port. Set the port speed to be either 10MB, 100MB, or gig. Set the port speed to auto to enable automatic port speed detection. The default value for this object depends upon the platform.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenMb(1), hundredMb(2), gig(3), auto(4), tenGig(5)

wwpLeosEtherPortOperSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.10
The current operational speed of the port.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), tenMb(1), hundredMb(2), gig(3), tenGig(4)

wwpLeosEtherPortAdminDuplex		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.11
The desired mode for the port. It can be set to either half or full duplex operation. The default value for this object depends upon the platform.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	half(1), full(2)

wwpLeosEtherPortOperDuplex		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.12
The current duplex mode of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	half(1), full(2)

wwpLeosEtherPortAdminFlowCtrl		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.13
Configures the ports flow control operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), off(2), asymTx(3), asymRx(4), sym(5)

wwpLeosEtherPortOperFlowCtrl		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.14
Shows ports flow control configuration.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), off(2), asymTx(3), asymRx(4), sym(5)

wwpLeosEtherIngressPvid		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.15
The Ingress PVID, the VLAN ID associated with untagged frames ingressing the port or if tunnel is enabled on this port. The max value for this object is platform dependent. Refer to architecture document for details of platform dependency.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..24576

wwpLeosEtherUntagEgressVlanId		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.16
All the egress frames whose VLAN id matches the wwpLeosEtherUntagEgressVlanId, will egress the port as untagged. To egress the frames tagged set wwpLeosEtherUntagEgressVlanId to 0. The max value for this object is platform dependent. Refer to architecture document for details of platform dependency.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..24576

wwpLeosEtherPortAcceptableFrameTypes		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.17
When this is admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged frames received on this port. When admitOnlyUntagged(3) is set, the device will discard VLAN tagged frames received on this port. With admitOnlyUntagged(3) and admitAll(1), untagged frames or Priority-Tagged frames received on this port will be accepted and assigned to the PVID for this port. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	admitAll(1), admitOnlyVlanTagged(2), admitOnlyUntagged(3)

wwpLeosEtherPortUntaggedPriority		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.18
The 802.1p packet priority to be assigned to packets ingressing this port that do not have an 802.1Q VLAN header. This priority is also assigned to ingress frame if tunnel is enabled on this port.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7)

wwpLeosEtherPortMaxFrameSize		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.19
Setting this object will set the max frame size allowed on a port. The max frame size can vary from 1522 bytes to 9216 bytes. Default value is 1526 bytes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1522..9216

wwpLeosEtherPortVlanIngressFiltering		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.20
When this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortAdminAdvertisedFlowCtrl		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.21
This object specifies the advertised flow control for given port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), off(2), asymTx(3), sym(4), symAsymRx(5)

wwpLeosEtherPortVplsPortType		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.22
This object specifies whether port is in subscriber type, network facing side or both.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notDefined(1), subscriber(2), networkFacing(3)

wwpLeosEtherPortIngressCosPolicy		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.23
This object specifies the ingress cos policy to be applied to all frames coming in on the given port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	leave(1), fixed(2), ippInherit(3), phbgInherit(4)

wwpLeosEtherPortIngressFixedDot1dPri		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.24
The 802.1p packet priority to be assigned to packets ingressing this port that do not have an 802.1Q VLAN header. This priority is also assigned to ingress untagged frame if the virtual switch cos policy is set to 'fix' for a given port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

wwpLeosEtherPortUntagDataVsi		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.25
This object specifies the virtual switch to be used for this port if data frame is untagged. If this object is set to 0 then device will unset this object. When setting this object to Mpls Vsi Index then wwpLeosEtherPortUntagDataVsiType must also be set to mpls (Use multiple set operation)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

wwpLeosEtherPortOperationalSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.26
An estimate of the port's current bandwidth in k-bits per second for given port.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

wwpLeosEtherPortUntagCtrlVsi		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.27
This object specifies the virtual switch to be used for this port if control frame is untagged. If this object is set to 0 then device will unset this object. When setting this object to Mpls Vsi Index then wwpLeosEtherPortUntagCtrlVsiType must also be set to mpls (Use multiple set operation)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

wwpLeosEtherPortMirrorPort		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.28
This object defines whether the port will allow traffic from other ports to be mirrored to this port. To allow traffic from other ports to be sent to this port, set this object to True(1). This port is known as a mirror port. If set to true, then other ports may set the values of their wwpLeosEtherPortMirrorIngress or wwpLeosEtherPortMirrorEgress objects to the port index of this port. Setting this object to false(2) disables this port as a mirror port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortMirrorIngress		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.29
The value of this object is the port index of a mirror port. The ingress traffic of this port can be mirrored by setting the destination port's wwpLeosEtherPortMirrorPort object to true. If the value of this object is set to zero this port's ingress traffic will not be mirrored.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

wwpLeosEtherPortMirrorEgress		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.30
The value of this object is the port index of a mirror port. The egress traffic of this port can be mirrored by setting the destination port's wwpLeosEtherPortMirrorPort object to true. If the value of this object is set to zero this port's egress traffic will not be mirrored.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

wwpLeosEtherPortUntagDataVsiType		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.31
This object specifies the virtual switch instance type associated with this port. This object defaults to ethernet and specifies if wwpLeosEtherPortUntagDataVsi belongs to ethernet virtual switch table (wwpLeosVplsVirtualSwitchEthTable in WWP-LEOS-VPLS-MIB) or mpls virtual switch table (wwpLeosVplsVirtualSwitchMplsTable in WWP-LEOS-VPLS-MIB). When setting wwpLeosEtherPortUntagDataVsi to MPLS Vsi Index then this object must also be set to mpls (Use mutliple set operation).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), mpls(2)

wwpLeosEtherPortUntagCtrlVsiType		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.32
This object specifies the virtual switch instance type associated with this port. This object defaults to ethernet and specifies if wwpLeosEtherPortUntagCtrlVsi belongs to ethernet virtual switch table (wwpLeosVplsVirtualSwitchEthTable) or mpls virtual switch table (wwpLeosVplsVirtualSwitchMplsTable). When setting wwpLeosEtherPortUntagCtrlVsi to MPLS Vsi Index then this object must also be set to mpls (Use mutliple set operation)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), mpls(2)

wwpLeosEtherPortVsIngressFiltering		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.33
This item is applicable to this port when the port is added as a per-port member to a virtual switch. If true(1) the device will discard incoming tagged frames. If false(2) the device will forwared incoming tagged frames so long as those customer tagged frames do not match another virtual switch with this port included as a per-port-per-vlan member.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortOperAutoNeg		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.34
The object specifies the operational auto neg state.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortUpTime		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.35
The object specifies the port up time in hundredths of a second.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

wwpLeosEtherPortUntagDataVid		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.36
The Ingress Untagged Data Vid, the VLAN ID stamped on untagged frames ingressing the port or if tunnel is enabled on this port. To disable tagging of untagged data on ingress write a value of 0. The max value for this object is platform dependent. Refer to architecture document for details of platform dependency.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..24576

wwpLeosEtherPortPhyLoopback		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.37
This object defines whether the phy has been placed in loopback mode, which causes frames egressing the port to be looped back to the port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortVlanIngressFilterStrict		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.38
This item is applicable to this port when the port is added as a to a virtual switch. If true(1) the legacy ingress filter behavior will be enforced at member addition (drop bit will be set to drop untagged traffic). If false, the splat bit will not be changed. Note that external VLAN associations are also maintained when strict is false.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortMacSaDaSwap		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.39
This object defines whether the MAC SA and DA will be swapped on frames egressing the port. This only works on a 311V.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortMacSaDaSwapVlan		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.40
This object defines whether the MAC SA and DA will be swapped on specific VLAN frames egressing the port. This only works on a 311V.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..24576

wwpLeosEtherPortResolvedCosPolicy		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.41
The Resolved Cost Policy. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dot1d(1), l3DscpCos(2), fixedCos(3), unknown(99)

wwpLeosEtherPortMode		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.42
The mode of the port Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rj45(1), sfp(2), default(3), unknown(99)

wwpLeosEtherFixedRcos		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.43
The fixed Resolve Cost value. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

wwpLeosEtherPortEgressPortQueueMapId		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.44
The Egress-port-Queue associated with this port. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

wwpLeosEtherPortResolvedCosMapId		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.45
RCOS map id for the port. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

wwpLeosEtherPortResolvedCosRemarkL2		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.46
The object specifies whether to remark L2 based on L3. This applies when the resolved cos policy is either l3-dscp-cos or dot1d-tag1-cos but not when it is fixed-cos policy. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortL2TransformMode		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.47
L2 transform action for port. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), iPush-e-Pop(1), iStamp-Push-e-QualifiedPopStamp(2), iPush-e-PopStamp(3)

wwpLeosEtherPortLinkFlapDetection		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.48
This object defines whether link flap detection will be enabled on the port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortLinkFlapCount		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.49
This object defines how many link down events are required to trigger a link flap event.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..64

wwpLeosEtherPortLinkFlapDetectTime		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.50
This object defines the time in seconds during which link down events are accumlated to trigger a link flap event.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..600

wwpLeosEtherPortLinkFlapHoldTime		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.51
This object defines the time in seconds that a port will be operationally disabled after a link flap event, before it is re-enabled. A value of zero causes the port to remain disabled until manually enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..600

wwpLeosEtherFixedRColor		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.52
This sets the fixed color to green (default) or yellow. Setting this attribute is not supported in saos version 4
Status: current	Access: read-write
OBJECT-TYPE
	PortIngressFixedColor

wwpLeosEtherPortFrameCosMapId		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.53
Frame COS map id for the port. Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

wwpLeosEtherPortEgressCosPolicy		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.54
Sets the egress frame cos policy Setting this attribute is not supported in leos version 4
Status: current	Access: read-write
OBJECT-TYPE
	PortEgressFrameCosPolicy

wwpLeosEtherPortEgressSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.55
An estimate of the port's current egress bandwidth restriction in k-bits per second for given port. A value of 0 means there is no active restriction. This attribute not supported in leos version 6
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

wwpLeosEtherPortAdaptiveRateSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.56
An estimate of the port's current adaptive-rate bandwidth restriction in k-bits per second for given port. A value of 0 means there is no active restriction. This attribute not supported in leos version 6
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

wwpLeosEtherPortMirrorEncap		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.57
This object defines whether the port will encapsulate mirrored frames by adding a vlan-tag. (Or, in the case where a mirrored frame is already tagged, by adding a further vlan-tag to the frame) To allow mirrored traffic to be encapsulated, set this object to vlan-tag(1). If set to vlan-tag, then the values of wwpLeosEtherPortMirrorEncapVid and wwpLeosEtherPortMirrorEncapTpid will be used to populate tag added to each mirrored frame. Setting this object to none(0) indicates no tag is to be added to the mirrored frames.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), vlanTag(1)

wwpLeosEtherPortMirrorEncapVid		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.58
This object defines the VID that will be added to mirrored frames when the mirroring encapsulation mode is vlan-tag
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..24576

wwpLeosEtherPortMirrorEncapTpid		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.59
This object defines the tpid used in the tag that is added to mirrored frames, when the mirroring encapsulation mode is vlan-tag
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tpid8100(1), tpid9100(2), tpid88A8(3)

wwpLeosEtherPortIfgDecrease		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.60
This object defines the number of bytes that will be subtracted from the minimum standard IFG of 12 bytes as defined in IEEE 802.3. SAOS 6.x only supports a value of 0 or 4.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..5

wwpLeosEtherPortAdvertSpeed		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.61
This object defines the speed capabilities that will be advertised during the auto-negotiation process.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	not-applicable(1), ten(2), hundred(3), gigabit(4), ten-hundred-gigabit(5)

wwpLeosEtherPortAdvertDuplex		1.3.6.1.4.1.6141.2.60.2.1.1.1.1.62
This object defines the duplex capabilities that will be advertised during the auto-negotiation process.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	not-applicable(1), half(2), full(3), half-full(4)

wwpLeosEtherPortFlushTable		1.3.6.1.4.1.6141.2.60.2.1.1.2
Table of port flush entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WwpLeosEtherPortFlushEntry

wwpLeosEtherPortFlushEntry		1.3.6.1.4.1.6141.2.60.2.1.1.2.1
Broadcast containment port entry in the Ethernet Port Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	WwpLeosEtherPortFlushEntry

wwpLeosEtherPortFlushActivate		1.3.6.1.4.1.6141.2.60.2.1.1.2.1.1
Setting this object to 'true' will cause the Macs to be flushed for the port specified by wwpLeosEtherPortId.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortTrapsTable		1.3.6.1.4.1.6141.2.60.2.1.1.3
Table of Ethernet Ports Traps.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WwpLeosEtherPortTrapsEntry

wwpLeosEtherPortTrapsEntry		1.3.6.1.4.1.6141.2.60.2.1.1.3.1
Port Traps Entry in the Ethernet Port Trap Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	WwpLeosEtherPortTrapsEntry

wwpLeosEtherPortTrapsState		1.3.6.1.4.1.6141.2.60.2.1.1.3.1.1
Setting this object will enable or disable all traps on given port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

wwpLeosEtherPortStateMirrorGroupTable		1.3.6.1.4.1.6141.2.60.2.1.1.4
This table can be used to keep track of all the port state mirror groups. To create entry in this table along with indexes following mib objects must be set using multiple set operation wwpLeosEtherPortStateMirrorGroupName must be valid string. wwpLeosEtherPortStateMirrorGroupStatus must be set.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WwpLeosEtherPortStateMirrorGroupEntry

wwpLeosEtherPortStateMirrorGroupEntry		1.3.6.1.4.1.6141.2.60.2.1.1.4.1
Each entry in this table will define the port state mirror group.
Status: current	Access: not-accessible
OBJECT-TYPE
	WwpLeosEtherPortStateMirrorGroupEntry

wwpLeosEtherPortStateMirrorGroupId		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.1
This mib object is used as index in the table and is used to identify the unique group id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

wwpLeosEtherPortStateMirrorGroupName		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.2
This mib object is used to specify the name of the group.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..15)

wwpLeosEtherPortStateMirrorGroupOperStatus		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.3
This mib object is used to specify the operational status of the group.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

wwpLeosEtherPortStateMirrorGroupNumSrcPorts		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.4
This mib object is used to specify the total number of source ports that exists in the group.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

wwpLeosEtherPortStateMirrorGroupNumDstPorts		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.5
This mib object is used to specify the total number of destination ports that exists in the group.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

wwpLeosEtherPortStateMirrorGroupStatus		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.6
Used to manage the creation and deletion of the conceptual rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wwpLeosEtherPortStateMirrorGroupType		1.3.6.1.4.1.6141.2.60.2.1.1.4.1.7
This mib object is used to specify the directional mode type for the port state mirror group. A uni-directional(1) mirror group type will only mirror the port state of the source port(s) to the destination port(s). The bi-directional(2) mirror group type will mirror state of either the source port(s) to the destination port(s) or the state of the destination port(s) will be mirrored to the source port(s). Where there are more than one source or destination ports the combined state of the source or destination group will be the combined 'OR'ed status of all the ports in either the source or destination groups. In other words, if one or more source ports is 'UP' then the source group is 'UP' and the mirrored destination state may be 'UP'. The default for this object type is uni-directional.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unidirectional(1), bidirectional(2)

wwpLeosEtherPortStateMirrorGroupMemTable		1.3.6.1.4.1.6141.2.60.2.1.1.5
This table is used to keep track of port group membership.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WwpLeosEtherPortStateMirrorGroupMemEntry

wwpLeosEtherPortStateMirrorGroupMemEntry		1.3.6.1.4.1.6141.2.60.2.1.1.5.1
Each entry in this table is used to represent the membership of port to a given group and group type.
Status: current	Access: not-accessible
OBJECT-TYPE
	WwpLeosEtherPortStateMirrorGroupMemEntry

wwpLeosEtherPortStateMirrorGroupMemType		1.3.6.1.4.1.6141.2.60.2.1.1.5.1.1
Setting this object will specify the type of group this port is member of for a given port state mirror group. This object can only be set while creating the entry. This object cannot be modified once entry is created.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	srcPort(1), dstPort(2)

wwpLeosEtherPortStateMirrorGroupMemOperState		1.3.6.1.4.1.6141.2.60.2.1.1.5.1.2
This mib object is used to specify the operational status of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

wwpLeosEtherPortStateMirrorGroupMemStatus		1.3.6.1.4.1.6141.2.60.2.1.1.5.1.3
Used to manage the creation and deletion of the conceptual rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wwpLeosEtherStndLinkUpDownTrapsEnable		1.3.6.1.4.1.6141.2.60.2.1.2.1
Setting this object to 'false(2)' will cause standard Link Up Down Traps to be suppressed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherPortLinkUpDownTrapsEnable		1.3.6.1.4.1.6141.2.60.2.1.2.2
Setting this object to 'true(1)' will cause wwp specific port up down trap to be generated.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEtherAggPortLinkUpDownTrapsEnable		1.3.6.1.4.1.6141.2.60.2.1.2.3
Setting this object to 'true(1)' will cause wwp specific agg port up down trap to be generated for a link state change on a physical port that is a member of a agg.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

wwpLeosEthLinkUp		1.3.6.1.4.1.6141.2.60.2.2.0.3
A wwpLeosEthLinkUp trap signifies that the SNMP entity, acting in an agent role, has detected that the ifOperStatus object for one of its communication links has entered the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

wwpLeosEthLinkDown		1.3.6.1.4.1.6141.2.60.2.2.0.4
A wwpLeosEthLinkDown trap signifies that the SNMP entity, acting in an agent role, has detected that the ifOperStatus object for one of its communication links has entered the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

wwpLeosEthAdminSpeedIncompatible		1.3.6.1.4.1.6141.2.60.2.2.0.5
A wwpLeosEthAdminSpeedIncompatible trap is generated when the port administrative speed doesn't match the speed of the SFP transceiver installed.
Status: current	Access: read-write
NOTIFICATION-TYPE

wwpLeosEthLinkFlap		1.3.6.1.4.1.6141.2.60.2.2.0.6
A wwpLeosEthLinkFlap trap signifies that the SNMP entity, acting in an agent role, has detected that the ifOperStatus object for one of its communication links has been changed due to link flap detection.
Status: current	Access: read-write
NOTIFICATION-TYPE

wwpLeosAggLinkUpDown		1.3.6.1.4.1.6141.2.60.2.2.0.7
A wwpLeosAggLinkUpDown trap signifies that the SNMP entity, acting in an agent role, has detected that the ifOperStatus object for one of its communication links has changed state.
Status: current	Access: read-write
NOTIFICATION-TYPE