WWP-LEOS-VPLS-MIB

File: WWP-LEOS-VPLS-MIB.mib (160020 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC WWP-SMI

Imported symbols

Integer32 Unsigned32 Counter32
IpAddress OBJECT-TYPE MODULE-IDENTITY
TruthValue DisplayString MacAddress
TEXTUAL-CONVENTION RowStatus wwpModulesLeos

Defined Types

VlanId  
A Vlan Id represents a Broadcast Domain.
TEXTUAL-CONVENTION    
  INTEGER 1..24576  

EtherType  
Ethernet v2 framing identifies upper layer protocol.
TEXTUAL-CONVENTION    
  Integer32 2048..65535  

WwpLeosVplsVirtualCircuitEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitIndex INTEGER
  wwpLeosVplsVirtualCircuitProviderVlanId VlanId
  wwpLeosVplsVirtualCircuitType INTEGER
  wwpLeosVplsVirtualCircuitName DisplayString
  wwpLeosVplsVirtualCircuitIngressVcLabel INTEGER
  wwpLeosVplsVirtualCircuitEgressVcLabel INTEGER
  wwpLeosVplsVirtualCircuitTunnelIndx INTEGER
  wwpLeosVplsVirtualCircuitStatus RowStatus

WwpLeosVplsVirtualSwitchEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchIndx INTEGER
  wwpLeosVplsVirtualSwitchName OCTET STRING
  wwpLeosVplsVirtualSwitchPriVc INTEGER
  wwpLeosVplsVirtualSwitchSecVc INTEGER
  wwpLeosVplsVirtualSwitchActiveVc INTEGER
  wwpLeosVplsVirtualSwitchEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchEncapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchDecapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchDecapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchSubscriberVlan INTEGER
  wwpLeosVplsVirtualSwitchCtrlProtocolTunnelState INTEGER
  wwpLeosVplsVirtualSwitchType INTEGER
  wwpLeosVplsVirtualSwitchStatus RowStatus

WwpLeosVplsVirtualSwitchMemberEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMemberPortId INTEGER
  wwpLeosVplsVirtualSwitchMemberStatus RowStatus

WwpLeosVplsSwitchCtrlProtocolEntry  
SEQUENCE    
  wwpLeosVplsSwitchCtrlProtocolNum INTEGER
  wwpLeosVplsSwitchCtrlType INTEGER

WwpLeosVplsSwitchReservedVlanEntry  
SEQUENCE    
  wwpLeosVplsSwitchReservedVlanId INTEGER
  wwpLeosVplsSwitchReservedVlanStatus RowStatus

WwpLeosVplsMplsPathEntry  
SEQUENCE    
  wwpLeosVplsMplsPathIndex INTEGER
  wwpLeosVplsMplsPathName DisplayString
  wwpLeosVplsMplsPathRowStatus RowStatus

WwpLeosVplsMplsPathMemberEntry  
SEQUENCE    
  wwpLeosVplsMplsPathOptionIndex INTEGER
  wwpLeosVplsMplsPathMemberIpIndex INTEGER
  wwpLeosVplsMplsPathMemberIp IpAddress
  wwpLeosVplsMplsPathMemberRowStatus RowStatus

WwpLeosVplsRsvpAttrEntry  
SEQUENCE    
  wwpLeosVplsRsvpAttrIndex INTEGER
  wwpLeosVplsRsvpAttrHoldPri INTEGER
  wwpLeosVplsRsvpAttrSetupPri INTEGER
  wwpLeosVplsRsvpAttrRecordRoute TruthValue

WwpLeosVplsEncapTunnelEntry  
SEQUENCE    
  wwpLeosVplsEncapTunnelId INTEGER
  wwpLeosVplsEncapTunnelName DisplayString
  wwpLeosVplsEncapTunnelType INTEGER
  wwpLeosVplsEncapTunnelDestAddr IpAddress
  wwpLeosVplsEncapTunnelPathIndex Integer32
  wwpLeosVplsEncapTunnelEncapCosPolicy INTEGER
  wwpLeosVplsEncapTunnelEncapFixedExp INTEGER
  wwpLeosVplsEncapTunnelTTLPolicy INTEGER
  wwpLeosVplsEncapTunnelEncapLabel Unsigned32
  wwpLeosVplsEncapTunnelProtType INTEGER
  wwpLeosVplsEncapTunnelDestResolvedMac MacAddress
  wwpLeosVplsEncapTunnelOperStatus INTEGER
  wwpLeosVplsEncapTunnelAdminStatus INTEGER
  wwpLeosVplsEncapTunnelDestResolvedPort INTEGER
  wwpLeosVplsEncapTunnelDestResolvedVlan INTEGER
  wwpLeosVplsEncapTunnelRowStatus RowStatus
  wwpLeosVplsEncapTunnelFastReroute INTEGER
  wwpLeosVplsEncapTunnelLspType INTEGER
  wwpLeosVplsEncapTunnelPartnerTunnelId INTEGER
  wwpLeosVplsEncapTunnelBVID VlanId
  wwpLeosVplsEncapTunnelDestBridgeIndex Integer32
  wwpLeosVplsEncapTunnelEgressPort Integer32
  wwpLeosVplsEncapTunnelEncapFixedPCP INTEGER
  wwpLeosVplsEncapTunnelActive INTEGER

WwpLeosVplsDecapTunnelEntry  
SEQUENCE    
  wwpLeosVplsDecapTunnelId INTEGER
  wwpLeosVplsDecapTunnelName DisplayString
  wwpLeosVplsDecapTunnelLabel Unsigned32
  wwpLeosVplsDecapTunnelType INTEGER
  wwpLeosVplsDecapTunnelRowStatus RowStatus
  wwpLeosVplsDecapTunnelBVID Integer32
  wwpLeosVplsDecapTunnelBridgeIndex Integer32
  wwpLeosVplsDecapTunnelPort Integer32
  wwpLeosVplsDecapTunnelMac MacAddress
  wwpLeosVplsDecapTunnelOperStatus INTEGER

WwpLeosVplsVirtualCircuitMplsEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitMplsIndex INTEGER
  wwpLeosVplsVirtualCircuitMplsName DisplayString
  wwpLeosVplsVirtualCircuitMplsType INTEGER
  wwpLeosVplsVirtualCircuitMplsDestAddr IpAddress
  wwpLeosVplsVirtualCircuitMplsTunnelPolicy INTEGER
  wwpLeosVplsVirtualCircuitMplsFixedTunnelId INTEGER
  wwpLeosVplsVirtualCircuitMplsActiveTunnelId INTEGER
  wwpLeosVplsVirtualCircuitMplsOperStatus INTEGER
  wwpLeosVplsVirtualCircuitMplsEncapLabel Unsigned32
  wwpLeosVplsVirtualCircuitMplsDecapLabel Unsigned32
  wwpLeosVplsVirtualCircuitMplsGroupId Unsigned32
  wwpLeosVplsVirtualCircuitMplsProtectionType INTEGER
  wwpLeosVplsVirtualCircuitMplsStatusTlv INTEGER
  wwpLeosVplsVirtualCircuitMplsMtu INTEGER
  wwpLeosVplsVirtualCircuitMplsStatus RowStatus

WwpLeosVplsVirtualCircuitMplsStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitMplsTxBytesHi Counter32
  wwpLeosVplsVirtualCircuitMplsTxBytesLo Counter32
  wwpLeosVplsVirtualCircuitMplsRxBytesHi Counter32
  wwpLeosVplsVirtualCircuitMplsRxBytesLo Counter32

WwpLeosVplsVirtualCircuitEthEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitEthIndex INTEGER
  wwpLeosVplsVirtualCircuitEthName DisplayString
  wwpLeosVplsVirtualCircuitEthProviderVlanId VlanId
  wwpLeosVplsVirtualCircuitEthRowStatus RowStatus
  wwpLeosVplsVirtualCircuitEthStatsMonitor INTEGER

WwpLeosVplsVirtualCircuitEtherTypeEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitPortId INTEGER
  wwpLeosVplsVirtualCircuitEtherType INTEGER
  wwpLeosVplsVirtualCircuitEtherTypePolicy INTEGER

WwpLeosVplsVirtualCircuitEthStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitEthTxBytesHi Counter32
  wwpLeosVplsVirtualCircuitEthTxBytesLo Counter32
  wwpLeosVplsVirtualCircuitEthRxBytesHi Counter32
  wwpLeosVplsVirtualCircuitEthRxBytesLo Counter32
  wwpLeosVirtualCircuitEthStatsClear INTEGER

WwpLeosVplsVirtualSwitchMplsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsIndx INTEGER
  wwpLeosVplsVirtualSwitchMplsName DisplayString
  wwpLeosVplsVirtualSwitchMplsVpnId Unsigned32
  wwpLeosVplsVirtualSwitchMplsEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsEncapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchMplsDecapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsDecapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchMplsCtrlProtocolTunnelState INTEGER
  wwpLeosVplsVirtualSwitchMplsDecapTTLPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsType INTEGER
  wwpLeosVplsVirtualSwitchMplsRowStatus RowStatus
  wwpLeosVplsVirtualSwitchMplsMacLrnState INTEGER
  wwpLeosVplsVirtualSwitchMplsTunnelMethod INTEGER
  wwpLeosVplsVirtualSwitchMplsCtrlProtocolDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchMplsSubscriberDot1dPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsCtrlProtTransFrameValidate INTEGER
  wwpLeosVplsVirtualSwitchMplsHonorPriority INTEGER

WwpLeosVplsVirtualSwitchMplsMemberEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsMemberPortId INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberVlanId INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberRowStatus RowStatus
  wwpLeosVplsVirtualSwitchMplsMemberEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberEncapCosFixedDot1DPri INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberSubscriberDot1dPolicy INTEGER

WwpLeosVplsVirtualSwitchMplsMemberStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsMemberRxBytesHi Counter32
  wwpLeosVplsVirtualSwitchMplsMemberRxBytesLo Counter32

WwpLeosVplsVirtualSwitchMplsMemberMeshVcEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsMemberMeshVcMeshVc INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberMeshVcRowStatus RowStatus

WwpLeosVplsVirtualSwitchMplsMemberAcVcEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsMemberAcVcAcVc INTEGER
  wwpLeosVplsVirtualSwitchMplsMemberAcVcRowStatus RowStatus

WwpLeosVplsSwitchMplsCtrlProtocolEntry  
SEQUENCE    
  wwpLeosVplsSwitchMplsCtrlProtocolNum INTEGER
  wwpLeosVplsSwitchMplsCtrlType INTEGER

WwpLeosVplsVirtualSwitchEthEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthIndx INTEGER
  wwpLeosVplsVirtualSwitchEthName DisplayString
  wwpLeosVplsVirtualSwitchEthVc INTEGER
  wwpLeosVplsVirtualSwitchEthEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthEncapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchEthDecapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthDecapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchEthCtrlProtocolTunnelState INTEGER
  wwpLeosVplsVirtualSwitchEthRowStatus RowStatus
  wwpLeosVplsVirtualSwitchEthMacLrnState INTEGER
  wwpLeosVplsVirtualSwitchEthTunnelMethod INTEGER
  wwpLeosVplsVirtualSwitchEthCtrlProtocolDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchEthSubscriberDot1dPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthCtrlProtTransFrameValidate INTEGER
  wwpLeosVplsVirtualSwitchEthVcType INTEGER
  wwpLeosVplsVirtualSwitchEthHonorPriority INTEGER
  wwpLeosVplsVirtualSwitchEthDescription OCTET STRING
  wwpLeosVplsVirtualSwitchEthReservedVlan INTEGER

WwpLeosVplsVirtualSwitchEthMemberEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthMemberPortId INTEGER
  wwpLeosVplsVirtualSwitchEthMemberVlan INTEGER
  wwpLeosVplsVirtualSwitchEthMemberRowStatus RowStatus
  wwpLeosVplsVirtualSwitchEthMemberEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthMemberEncapCosFixedDot1DPri INTEGER
  wwpLeosVplsVirtualSwitchEthMemberSubscriberDot1dPolicy INTEGER

WwpLeosVplsVirtualSwitchEthMemberStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthMemberRxBytesHi Counter32
  wwpLeosVplsVirtualSwitchEthMemberRxBytesLo Counter32

WwpLeosVplsSwitchEthCtrlProtocolEntry  
SEQUENCE    
  wwpLeosVplsSwitchEthCtrlProtocolNum INTEGER
  wwpLeosVplsSwitchEthCtrlType INTEGER

WwpLeosVplsVirtualSwitchEtypeTranslationEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEtypeTranslationOriginalEtype EtherType
  wwpLeosVplsVirtualSwitchEtypeTranslationMappedEtype EtherType
  wwpLeosVplsVirtualSwitchEtypeTranslationRowStatus RowStatus

WwpLeosVplsTunnelPairEntry  
SEQUENCE    
  wwpLeosVplsTunnelPairIndx INTEGER
  wwpLeosVplsTunnelPairName DisplayString
  wwpLeosVplsTunnelPairEncapTunnelIndx Integer32
  wwpLeosVplsTunnelPairDecapTunnelIndx Integer32
  wwpLeosVplsTunnelPairRowStatus RowStatus

WwpLeosVplsVirtualSwitchMplsEvplMemberEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsEvplMemberPortId INTEGER
  wwpLeosVplsVirtualSwitchMplsEvplMemberVlanId INTEGER
  wwpLeosVplsVirtualSwitchMplsEvplMemberRowStatus RowStatus
  wwpLeosVplsVirtualSwitchMplsEvplMemberEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchMplsEvplMemberEncapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchMplsEvplMemberSubscriberDot1dPolicy INTEGER

WwpLeosVplsVirtualSwitchMplsEvplMemberStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesHi Counter32
  wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesLo Counter32

WwpLeosVplsVirtualSwitchEthEvplMemberEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthEvplMemberPortId INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberVlan INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberRowStatus RowStatus
  wwpLeosVplsVirtualSwitchEthEvplMemberEncapCosPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberEncapFixedDot1dPri INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberSubscriberDot1dPolicy INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberTranslateTag INTEGER
  wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid INTEGER

WwpLeosVplsVirtualSwitchEthEvplMemberStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesHi Counter32
  wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesLo Counter32

WwpLeosVplsVirtualCircuitEthTotalStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitEthTotalTxBytesHi Counter32
  wwpLeosVplsVirtualCircuitEthTotalTxBytesLo Counter32
  wwpLeosVplsVirtualCircuitEthTotalRxBytesHi Counter32
  wwpLeosVplsVirtualCircuitEthTotalRxBytesLo Counter32

WwpLeosVplsVirtualCircuitMplsTotalStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualCircuitMplsTotalTxBytesHi Counter32
  wwpLeosVplsVirtualCircuitMplsTotalTxBytesLo Counter32
  wwpLeosVplsVirtualCircuitMplsTotalRxBytesHi Counter32
  wwpLeosVplsVirtualCircuitMplsTotalRxBytesLo Counter32

WwpLeosVplsVirtualSwitchEthL2CftProtocolEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchEthL2CftProtocolType INTEGER
  wwpLeosVplsVirtualSwitchEthL2CftProtocolDisposition INTEGER
  wwpLeosVplsVirtualSwitchEthL2CftProtocolRowStatus RowStatus

WwpLeosVplsVirtualSwitchCFTProtoStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchCFTProtoStatsEntryVirtualSwitchIndx INTEGER
  wwpLeosVplsVirtualSwitchCFTProtol2RxPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2TunneledPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2PeerPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2DiscardedPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2DecodedPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2DecodedFailures Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2TunneledSubcriberPortPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtol2ProtocolNum INTEGER

WwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntry  
SEQUENCE    
  wwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntryVirtualSwitchIndx INTEGER
  wwpLeosVplsVirtualSwitchCFTProtoTotall2RxPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2PeerPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2DiscardedPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedFailures Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledSubcriberPortPkts Counter32
  wwpLeosVplsVirtualSwitchCFTProtoTotall2ProtocolNum INTEGER

Defined Values

wwpLeosVplsMIB 1.3.6.1.4.1.6141.2.60.28
Added a new object wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid.
MODULE-IDENTITY    

wwpLeosVplsMIBObjects 1.3.6.1.4.1.6141.2.60.28.1
OBJECT IDENTIFIER    

wwpLeosVpls 1.3.6.1.4.1.6141.2.60.28.1.1
OBJECT IDENTIFIER    

wwpLeosVplsMIBNotificationPrefix 1.3.6.1.4.1.6141.2.60.28.2
OBJECT IDENTIFIER    

wwpLeosVplsMIBNotifications 1.3.6.1.4.1.6141.2.60.28.2.0
OBJECT IDENTIFIER    

wwpLeosVplsMIBConformance 1.3.6.1.4.1.6141.2.60.28.3
OBJECT IDENTIFIER    

wwpLeosVplsMIBCompliances 1.3.6.1.4.1.6141.2.60.28.3.1
OBJECT IDENTIFIER    

wwpLeosVplsMIBGroups 1.3.6.1.4.1.6141.2.60.28.3.2
OBJECT IDENTIFIER    

wwpLeosVplsVirtualCircuitTable 1.3.6.1.4.1.6141.2.60.28.1.1.1
The (conceptual) table listing the virtual circuit table. To create entry use SNMP, multiple set operation must be used because following MIB objects needs to be set while creating entry in the table. - wwpLeosVplsVirtualCircuitIndex - wwpLeosVplsVirtualCircuitProviderVlanId (should exist on the device) - wwpLeosVplsVirtualCircuitType - wwpLeosVplsVirtualCircuitStatus. - wwpLeosVplsVirtualCircuitName.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitEntry

wwpLeosVplsVirtualCircuitEntry 1.3.6.1.4.1.6141.2.60.28.1.1.1.1
The virtual circuit table entry index by wwpLeosVplsVirtualCircuitIndex.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitEntry  

wwpLeosVplsVirtualCircuitIndex 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.1
This represents the virtual circuit index in the table. This number should be unique in the table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualCircuitProviderVlanId 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.2
This represents the provider vlan id associated with the virtual circuit for a given wwpLeosVplsVirtualCircuitIndex.
Status: deprecated Access: read-write
OBJECT-TYPE    
  VlanId  

wwpLeosVplsVirtualCircuitType 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.3
This represents the type of virtual circuit associated with the given virtual circuit.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER ethernet(1), mpls(2)  

wwpLeosVplsVirtualCircuitName 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.4
This represents the name of the virtual circuit associated with the given virtual circuit.
Status: deprecated Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsVirtualCircuitIngressVcLabel 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.5
This represents the vc label to be used for given virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 16..1048575  

wwpLeosVplsVirtualCircuitEgressVcLabel 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.6
This represents the vc label to be used for given virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 16..1048575  

wwpLeosVplsVirtualCircuitTunnelIndx 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.7
This represents the tunnel associated with this virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualCircuitStatus 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.8
Setting this object to 'createAndGo' will create the entry and by default will enable control frame and data frame tunnel . Setting this object to 'destroy' will delete the entry from the table for given vlan.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchTable 1.3.6.1.4.1.6141.2.60.28.1.1.5
This table is used to manage virtual switch entries on the device.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEntry

wwpLeosVplsVirtualSwitchEntry 1.3.6.1.4.1.6141.2.60.28.1.1.5.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchTable table. To create an entry in the table following criteria must be met. - wwpLeosVplsVirtualSwitchIndx must be specified. - wwpLeosVplsVirtualSwitchStatus must be specified. - wwpLeosVplsVirtualSwitchType must be specified. - wwpLeosVplsVirtualSwitchName must be specified
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEntry  

wwpLeosVplsVirtualSwitchIndx 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.1
This object specifies the virtual switch index which is used as unique index in the table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchName 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.2
This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later.
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..31)  

wwpLeosVplsVirtualSwitchPriVc 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.3
This object specifies the primary virtual circuit ID associated with this virtual switch. To unset it set this to 0.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsVirtualSwitchSecVc 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.4
This object specifies the secondary virtual circuit ID associated with this virtual switch. To unset it set this to 0. This object is applicable if wwpLeosVplsVirtualSwitchType = mpls.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsVirtualSwitchActiveVc 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.5
This object specifies the virtual circuit which is currently used by this virtual switch instance.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER none(1), primVc(2), secVc(3)  

wwpLeosVplsVirtualSwitchEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.6
This object specifies the ingress cos policy for given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4)  

wwpLeosVplsVirtualSwitchEncapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.7
This object specifies the ingress fixed cos attributes for given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchDecapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.8
This object specifies the egress cos policy for given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritVc(2), inheritTunnel(3), leave(4)  

wwpLeosVplsVirtualSwitchDecapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.9
This object specifies the egress cos attributes for given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchSubscriberVlan 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.10
This object specifies the subscriber vlan Id for given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

wwpLeosVplsVirtualSwitchCtrlProtocolTunnelState 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.11
This object enables or disables control protocol tunneling for a given virtual switch.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchType 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.12
This object specifies the type of virtual witch.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER ethernet(1), mpls(2)  

wwpLeosVplsVirtualSwitchStatus 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.13
This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.6
This table is used to create virtual switch membership entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMemberEntry

wwpLeosVplsVirtualSwitchMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.6.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchMemberTable table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMemberEntry  

wwpLeosVplsVirtualSwitchMemberPortId 1.3.6.1.4.1.6141.2.60.28.1.1.6.1.1
This object specifies the port id associated with wwpLeosVplsVirtualSwitchIndx.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMemberStatus 1.3.6.1.4.1.6141.2.60.28.1.1.6.1.2
This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table.
Status: deprecated Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsSwitchCtrlProtocolTable 1.3.6.1.4.1.6141.2.60.28.1.1.7
The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsSwitchCtrlProtocolEntry

wwpLeosVplsSwitchCtrlProtocolEntry 1.3.6.1.4.1.6141.2.60.28.1.1.7.1
The layer 2 virtual switch control frame protocol tunnel entry for the Vpls.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsSwitchCtrlProtocolEntry  

wwpLeosVplsSwitchCtrlProtocolNum 1.3.6.1.4.1.6141.2.60.28.1.1.7.1.1
This object represent the list of protocols the device can support.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER l28021x(1), rstp(2), ciscoCdp(3), ciscoDtp(4), ciscoPagp(5), ciscoPvst(6), ciscoUplinkFast(7), ciscoUdlp(8), ciscoVtp(9), gvrp(10), lacp(11), lacpMarker(12), oam(13), lldp(14), vlanBridge(15)  

wwpLeosVplsSwitchCtrlType 1.3.6.1.4.1.6141.2.60.28.1.1.7.1.2
Setting this object to 'discard' will cause wwpLeosVplsSwitchCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchCtrlProtocolNum frame to be tunneled.
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER discard(1), peer(2), tunnel(3)  

wwpLeosVplsSwitchReservedVlanTable 1.3.6.1.4.1.6141.2.60.28.1.1.8
The (conceptual) table listing the reserved Vlans used for virtual switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsSwitchReservedVlanEntry

wwpLeosVplsSwitchReservedVlanEntry 1.3.6.1.4.1.6141.2.60.28.1.1.8.1
The entry to reserve vlans for vlan switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsSwitchReservedVlanEntry  

wwpLeosVplsSwitchReservedVlanId 1.3.6.1.4.1.6141.2.60.28.1.1.8.1.1
This object is used to specify the vlan ID to be reserved for virtual switch. Reserved vlans are used when virtual switch is created.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..24576  

wwpLeosVplsSwitchReservedVlanStatus 1.3.6.1.4.1.6141.2.60.28.1.1.8.1.2
Setting this object to 'createandgo' will reserve the vlan for virtual switch. Setting this object to 'destroy will no longer be reserved for virtual switch.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsGlobalAttrs 1.3.6.1.4.1.6141.2.60.28.1.1.9
OBJECT IDENTIFIER    

wwpLeosVplsTunnelFixedTTL 1.3.6.1.4.1.6141.2.60.28.1.1.9.1
This object specifies the fixed TTL value for all tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 2..255  

wwpLeosVplsResolverTimeout 1.3.6.1.4.1.6141.2.60.28.1.1.9.2
Setting this object will set the PE resolver timeout. This timeout value decides how frequently PE resolver will arp for the destination IP specified by wwpLeosVplsEncapTunnelDestAddr.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..255  

wwpLeosVplsStaticLabelRangeStart 1.3.6.1.4.1.6141.2.60.28.1.1.9.3
Setting this object will set the lowest label that can be assigned to static encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsStaticLabelRangeStart and wwpLeosVplsStaticLabelRangeEnd. wwpLeosVplsStaticLabelRangeStart must always be less than wwpLeosVplsStaticLabelRangeEnd. The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16..1048575  

wwpLeosVplsStaticLabelRangeEnd 1.3.6.1.4.1.6141.2.60.28.1.1.9.4
Setting this object will set the maximum label that can be assigned to static encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsStaticLabelRangeStart and wwpLeosVplsStaticLabelRangeEnd. wwpLeosVplsStaticLabelRangeStart must always be less than wwpLeosVplsStaticLabelRangeEnd.The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16..1048575  

wwpLeosVplsDynamicLabelRangeStart 1.3.6.1.4.1.6141.2.60.28.1.1.9.5
Setting this object will set the lowest label that can be assigned to dynamic encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsDynamicLabelRangeStart and wwpLeosVplsDynamicLabelRangeEnd. wwpLeosVplsDynamicLabelRangeStart must always be less than wwpLeosVplsDynamicLabelRangeEnd.The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16..1048575  

wwpLeosVplsDynamicLabelRangeEnd 1.3.6.1.4.1.6141.2.60.28.1.1.9.6
Setting this object will set the maximum label that will be assigned to encap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsDynamicLabelRangeStart and wwpLeosVplsDynamicLabelRangeEnd. wwpLeosVplsDynamicLabelRangeStart must always be less than wwpLeosVplsDynamicLabelRangeEnd. The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16..1048575  

wwpLeosVplsVirtualCircuitStatsClear 1.3.6.1.4.1.6141.2.60.28.1.1.9.7
Setting this object to clear will reset statistics for all virtual circuits
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), none(2)  

wwpLeosVplsMplsPathTable 1.3.6.1.4.1.6141.2.60.28.1.1.10
Mpls Path table used to represent the explicit path for RSVP tunnels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsMplsPathEntry

wwpLeosVplsMplsPathEntry 1.3.6.1.4.1.6141.2.60.28.1.1.10.1
Entry in the MPLS Path table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsMplsPathEntry  

wwpLeosVplsMplsPathIndex 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.1
This mib specifies the unique entry in the Mpls path table. This is the primary index into this table identifying a particular explicit route object
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

wwpLeosVplsMplsPathName 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.2
This mib specifies the name for the path.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsMplsPathRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.3
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsMplsPathMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.11
Table specifies the list of IP addresses (Hops) to get to the destination PE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsMplsPathMemberEntry

wwpLeosVplsMplsPathMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.11.1
Represents the entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsMplsPathMemberEntry  

wwpLeosVplsMplsPathOptionIndex 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.1
Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

wwpLeosVplsMplsPathMemberIpIndex 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.2
Unique index to identify the IP address within the path specifies by wwpLeosVplsMplsPathIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

wwpLeosVplsMplsPathMemberIp 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.3
Specifies the IP address of the Hop that the tunnel the tunnel should traverse.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

wwpLeosVplsMplsPathMemberRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.4
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsRsvpAttrTable 1.3.6.1.4.1.6141.2.60.28.1.1.12
RSVP Attr Table used by MPLS wwpLeosVplsEncapTunnelTable Tunnels when wwpLeosVplsEncapTunnelProtType = rsvp. Whenever entry is created in the wwpLeosVplsEncapTunnelTable table with wwpLeosVplsEncapTunnelProtType = rsvp and wwpLeosVplsEncapTunnelType = dynamic then corresponding entry will be created in this table with the same index as wwpLeosVplsEncapTunnelId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsRsvpAttrEntry

wwpLeosVplsRsvpAttrEntry 1.3.6.1.4.1.6141.2.60.28.1.1.12.1
Entry in wwpLeosVplsRsvpAttrTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsRsvpAttrEntry  

wwpLeosVplsRsvpAttrIndex 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.1
Unique index into the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsRsvpAttrHoldPri 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.2
The Hold priority used by RSVP protocol when signaling for tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsRsvpAttrSetupPri 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.3
The setup priority used by RSVP protocol when signaling for tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsRsvpAttrRecordRoute 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.4
The object specifies if record route feature is enabled when RSVP protocol is used to signal tunnel LSP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wwpLeosVplsEncapTunnelTable 1.3.6.1.4.1.6141.2.60.28.1.1.13
This table represents the encap tunnels for VPLS. To create STATIC encap tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsEncapTunnelName must be specified. wwpLeosVplsEncapTunnelEncapLabel must be specified (0, 32..1023) wwpLeosVplsEncapTunnelType must be set to static wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo To create DYNAMIC encap tunnel following objects must be set wwpLeosVplsEncapTunnelName must be specified wwpLeosVplsEncapTunnelType must be set to dynamic wwpLeosVplsEncapTunnelProtType must be set to rsvp wwpLeosVplsEncapTunnelPathName must be specified, this path must exist in wwpLeosVplsMplsPathTable wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. wwpLeosVplsEncapTunnelFastReroute must be set if wanted to use fast reroute wwpLeosVplsEncapTunnelLspType must be specified, if not specified then it will be assumed primary To create DYNAMIC encap backup tunnel following objects must be set wwpLeosVplsEncapTunnelName must be set to primary tunnel name that this tunnel is backing up. wwpLeosVplsEncapTunnelType must be set to dynamic wwpLeosVplsEncapTunnelProtType must be set to rsvp wwpLeosVplsEncapTunnelPathName must be specified, this path must exist in wwpLeosVplsMplsPathTable wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. To create static PBT encap tunnel following objects must be set wwpLeosVplsEncapTunnelName must be specified wwpLeosVplsEncapTunnelType must be set to staticPbt wwpLeosVplsEncapTunnelBVID must be specified wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. wwpLeosVplsEncapTunnelDestBridgeIndex must be set wwpLeosVplsEncapTunnelEgressPort must be specified
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsEncapTunnelEntry

wwpLeosVplsEncapTunnelEntry 1.3.6.1.4.1.6141.2.60.28.1.1.13.1
Represents each entry in wwpLeosVplsEncapTunnelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsEncapTunnelEntry  

wwpLeosVplsEncapTunnelId 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.1
This object specifies the unique index used in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsEncapTunnelName 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.2
This object specfies the name assigned to this tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created. Encap and Decap Tunnel name cannot be same but indexes can be. When creating backup tunnel this name should be set to same name that is also used by primary tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsEncapTunnelType 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.3
This object specifies the type of tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), staticPbt(3)  

wwpLeosVplsEncapTunnelDestAddr 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.4
This object specifies the IP address used to resolve this tunnel. This object is only applicable if wwpLeosVplsEncapTunnelType not equal to staticPbt.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

wwpLeosVplsEncapTunnelPathIndex 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.5
This object specifies the path that this tunnel is supposed to use signal labels for this tunnel. This object is only used if wwpLeosVplsEncapTunnelType is set to dynamic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsEncapTunnelEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.6
This object specifies the PBT encapsulated cos policy assigned to this tunnel. inheritVC and inheritVs options are deprecated and should not be used. rcos-mapped option should be used in place of inheritVc
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritVc(2), inheritVs(3), rcosMapped(4)  

wwpLeosVplsEncapTunnelEncapFixedExp 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.7
This object specifies the encap fixed EXP assigned to this tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsEncapTunnelTTLPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.8
This object specifies the TTL policy for given tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pipe(1), uniform(2)  

wwpLeosVplsEncapTunnelEncapLabel 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.9
This mib object specifies the encap label assigned to this tunnel. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..1048576  

wwpLeosVplsEncapTunnelProtType 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.10
Setting this object at the time of entry creation will specify the type of Protocol to be used for this tunnel. This object is only used if wwpLeosVplsEncapTunnelType is set to dynamic. This object cannot be modified after the entry has been created.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), rsvp(2)  

wwpLeosVplsEncapTunnelDestResolvedMac 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.11
This object specifies the resolved mac address for given destination IP (wwpLeosVplsEncapTunnelDestIp).
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wwpLeosVplsEncapTunnelOperStatus 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.12
This mib object represents the operational status of tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsEncapTunnelAdminStatus 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.13
This mib object represents the administrative status of tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsEncapTunnelDestResolvedPort 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.14
This mib object represents the resolved port number to destination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsEncapTunnelDestResolvedVlan 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.15
This mib object represents the resolved transport vlan to destination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4094  

wwpLeosVplsEncapTunnelRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.16
Setting this object to 'createAndGo' will create the entry in the table. Setting this object to 'destroy' will delete the entry from the table. Refer to description of wwpLeosVplsEncapTunnelTable for details of creating and deleting entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsEncapTunnelFastReroute 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.17
This object specifies if the backup tunnel should provide link or node protection. This object should only be specified if wwpLeosVplsEncapTunnelType = dynamic and wwpLeosVplsEncapTunnelLspType = backup. This object cannot be modified once created.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER linkProtect(1), nodeProtect(2)  

wwpLeosVplsEncapTunnelLspType 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.18
This object specifies if the tunnel lsp is primary or backup tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER primary(1), backup(2)  

wwpLeosVplsEncapTunnelPartnerTunnelId 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.19
This object specifies if the partner tunnel ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsEncapTunnelBVID 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.20
This object specifies the provider backbone bridge vlan. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

wwpLeosVplsEncapTunnelDestBridgeIndex 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.21
This object specifies the provider backbone bridge index. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored. This object must be set to one of the values specified by wwpLeosPbtBridgeNameMacMapIndex. If this object is set to 0 then this value will be ignored.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..64  

wwpLeosVplsEncapTunnelEgressPort 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.22
This object specifies the provider backbone bridge port. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsEncapTunnelEncapFixedPCP 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.23
This object specifies the encap fixed PCP assigned to this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsEncapTunnelActive 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.24
This object specifes if the tunnel is active, and it is only valid if TunnelType is staticPbt.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wwpLeosVplsDecapTunnelTable 1.3.6.1.4.1.6141.2.60.28.1.1.14
This table represents the Decap tunnels for VPLS wwpLeosVplsDecapTunnelType If not set will default to static To create STATIC Decap tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsDecapTunnelName must be specified wwpLeosVplsDecapTunnelLabel must be specified (0, 32..1023) wwpLeosVplsDecapTunnelRowStatus must be set to createAndGo. To create STATIC Decap PBT tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsDecapTunnelType must be set to staticPbt wwpLeosVplsDecapTunnelName must be specified wwpLeosVplsDecapTunnelBVID must be specified wwpLeosVplsDecapTunnelBridgeIndex must be specified wwpLeosVplsDecapTunnelPort must be specified wwpLeosVplsDecapTunnelRowStatus must be set to createAndGo.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsDecapTunnelEntry

wwpLeosVplsDecapTunnelEntry 1.3.6.1.4.1.6141.2.60.28.1.1.14.1
represents each entry in wwpLeosVplsDecapTunnelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsDecapTunnelEntry  

wwpLeosVplsDecapTunnelId 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.1
This object specifies the unique index used in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsDecapTunnelName 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.2
This object specfies the name assigned to the tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsDecapTunnelLabel 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.3
This mib object specifies the Decap label assigned to this tunnel. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..1048576  

wwpLeosVplsDecapTunnelType 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.4
This object specifies if the tunnel is created because of remote PE request (dynamic tunnel) or it is created by the user on the device (Decap tunnel). This object cannot be set to dynamic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), staticPbt(3)  

wwpLeosVplsDecapTunnelRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.5
Setting this object to 'createAndGo' will create the entry in the table. Setting this object to 'destroy' will delete the entry from the table. Refer to description of wwpLeosVplsDecapTunnelTable for details of creating and deleting entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsDecapTunnelBVID 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.6
This object specifies the provider bridge vlan ID expected in the mac in mac frames ingressing the device from provider bridge facing side.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsDecapTunnelBridgeIndex 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.7
This object specifies the provider bridge host index which will be used to query wwpLeosPbtHostNameMacMapTable to find out corresponding mac address expected in the pbt frames ingressing the device from provider bridge facing side.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..64  

wwpLeosVplsDecapTunnelPort 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.8
This object specifies the incoming port on which the pbt frames are expected.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsDecapTunnelMac 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.9
This object specifies the source mac address expected in the pbt frames coming from provider network facing side. This mac address is derived from wwpLeosPbtHostNameMacMapTable table using the value specified by wwpLeosVplsDecapTunnelBridgeName.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wwpLeosVplsDecapTunnelOperStatus 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.10
This object represents the operational status of tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualCircuitMplsTable 1.3.6.1.4.1.6141.2.60.28.1.1.15
The (conceptual) table listing the mpls virtual circuit table. To create entry use SNMP, multiple set operation must be used. Following Mib objects must be specified while creating MPLS virtual circuit Mpls and Ethernet virtual circuit name cannot be same but indexes can be - wwpLeosVplsVirtualCircuitMplsType must be set to dynamic - wwpLeosVplsVirtualCircuitMplsStatus must be set to createAndGo - wwpLeosVplsVirtualCircuitMplsName must be specified - wwpLeosVplsVirtualCircuitMplsDestAddr must be specified Following MIB objects must be specified while creating static MPLS virtual circuit - wwpLeosVplsVirtualCircuitMplsType must be set to static - wwpLeosVplsVirtualCircuitMplsStatus must be set to createAndGo - wwpLeosVplsVirtualCircuitMplsName must be specified - wwpLeosVplsVirtualCircuitMplsDestAddr must be specified - wwpLeosVplsVirtualCircuitMplsEncapLabel must be specified (2048..18431) - wwpLeosVplsVirtualCircuitMplsDecapLabel must be specified (2048..18431)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitMplsEntry

wwpLeosVplsVirtualCircuitMplsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.15.1
The virtual circuit table entry index by wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitMplsEntry  

wwpLeosVplsVirtualCircuitMplsIndex 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.1
This represents the virtual circuit index in the table. This number should be unique in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualCircuitMplsName 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.2
This represents the name of the virtual circuit associated with the given virtual circuit. Mpls and Ethernet virtual circuit name cannot be same but indexes can be.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsVirtualCircuitMplsType 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.3
This represents the type of the virtual circuit.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dynamic(1), static(2)  

wwpLeosVplsVirtualCircuitMplsDestAddr 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.4
This represents the destination address used by the signaling protocol if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. This object cannot be modified once entry is created.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

wwpLeosVplsVirtualCircuitMplsTunnelPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.5
This object represents that this virtual circuit should select the tunnel as fixed or use the first active tunnel available on the outgoing port. If this object is set to fixed then wwpLeosVplsVirtualCircuitMplsTunnelIndx must be specified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER fixed(1), firstAvailable(2)  

wwpLeosVplsVirtualCircuitMplsFixedTunnelId 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.6
This represents the tunnel that this virtual circuit should be mapped to. This object is only used if wwpLeosVplsVirtualCircuitMplsTunnelPolicy is set to fixed.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsVirtualCircuitMplsActiveTunnelId 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.7
This represents the tunnel that this virtual circuit is currently using. This object is equal to wwpLeosVplsVirtualCircuitMplsFixedTunnelId if wwpLeosVplsVirtualCircuitMplsTunnelPolicy is set to fixed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsVirtualCircuitMplsOperStatus 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.8
This represents the operational status of the virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualCircuitMplsEncapLabel 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.9
If wwpLeosVplsVirtualCircuitMplsType is set to static then this object specifies the encap label the should be used for this virtual circuit. Label should be in the range 2048..18431. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1048576  

wwpLeosVplsVirtualCircuitMplsDecapLabel 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.10
If wwpLeosVplsVirtualCircuitMplsType is set to static then this object specifies the decap label the should be used for this virtual circuit. Label should be in the range 2048..18431. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1048576  

wwpLeosVplsVirtualCircuitMplsGroupId 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.11
This represents the group ID advertised in the LDP signaling if wwpLeosVplsVirtualCircuitMplsType is set to dynamic.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

wwpLeosVplsVirtualCircuitMplsProtectionType 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.12
This represents that this virtual circuit is primary or secondary virtual circuit. If primary virtual circuit goes down that secondary virtual circuit will be used.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

wwpLeosVplsVirtualCircuitMplsStatusTlv 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.13
Specifies whether the Status TLV in LDP signaling should be advertised or not. This mib object is only used if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. This field cannot be modified while wwpLeosVplsVirtualCircuitMplsStatus is active
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

wwpLeosVplsVirtualCircuitMplsMtu 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.14
Setting this object will set the MTU for this VC. This MTU is advertised to the peer if wwpLeosVplsVirtualCircuitMplsType is set to dynamic.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1500..9216  

wwpLeosVplsVirtualCircuitMplsStatus 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.15
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualCircuitMplsStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.16
The (conceptual) table listing the mpls virtual circuit stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitMplsStatsEntry

wwpLeosVplsVirtualCircuitMplsStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.16.1
The mpls virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitMplsStatsEntry  

wwpLeosVplsVirtualCircuitMplsTxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.1
This represents the total number of higher 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsTxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.2
This represents the total number of lower 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.3
This represents the total number of higher 32 bits received for given mpls virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.4
This represents the total number of lower 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTable 1.3.6.1.4.1.6141.2.60.28.1.1.17
The (conceptual) table listing the virtual circuit table. To create entry use SNMP, multiple set operation must be usedd because following mib objects needs to be set while creating entry in the table. Mpls and Ethernet virtual circuit name cannot be same but indexes can be - wwpLeosVplsVirtualCircuitEthName must be specified - wwpLeosVplsVirtualCircuitEthProviderVlanId must be specified and must exist on the device. - wwpLeosVplsVirtualCircuitEthStatus must be specified.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitEthEntry

wwpLeosVplsVirtualCircuitEthEntry 1.3.6.1.4.1.6141.2.60.28.1.1.17.1
The virtual circuit table entry index by wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitEthEntry  

wwpLeosVplsVirtualCircuitEthIndex 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.1
This represents the virtual circuit index in the table. This number should be unique in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualCircuitEthName 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.2
This represents the name of the virtual circuit associated with the given virtual circuit. Mpls and Ethernet virtual circuit name cannot be same but indexes can be
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsVirtualCircuitEthProviderVlanId 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.3
This represents the provider vlan id associated with the virtual circuit for a given wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

wwpLeosVplsVirtualCircuitEthRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.4
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy' If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualCircuitEthStatsMonitor 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.5
To disable stats collection, set this object to off(2). To enable stats collection, set this object to on(1).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wwpLeosVplsVirtualCircuitEtherTypeTable 1.3.6.1.4.1.6141.2.60.28.1.1.18
The (conceptual) table listing the ether type to be used for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitEtherTypeEntry

wwpLeosVplsVirtualCircuitEtherTypeEntry 1.3.6.1.4.1.6141.2.60.28.1.1.18.1
The entry to assign ether type for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitEtherTypeEntry  

wwpLeosVplsVirtualCircuitPortId 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.1
This object specifies the port number used as index in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualCircuitEtherType 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.2
This object specifies the ethertype of the outer VLAN tag for given port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER type8100(1), type9100(2), type88A8(3)  

wwpLeosVplsVirtualCircuitEtherTypePolicy 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.3
This object specifies the policy for the ethertype of the outer VLAN tag for given port. All means all frames will have the type set in wwpLeosVplsVirtualCircuitEtherType. encapOnly means only Q-in-Q encapsulated frames will use that value. If wwpLeosVplsVirtualCircuitEtherType is set to type 8100 then ALL will always be the operational value for this item. vlanTpid means that the port will use the TPID configured for the vlan at egress.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), encapOnly(2), vlanTpid(3)  

wwpLeosVplsVirtualCircuitEthStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.19
The (conceptual) table listing the virtual circuit stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitEthStatsEntry

wwpLeosVplsVirtualCircuitEthStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.19.1
The ethernet virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitEthStatsEntry  

wwpLeosVplsVirtualCircuitEthTxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.1
This represents the total number of higher 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.2
This represents the total number of lower 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.3
This represents the total number of higher 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.4
This represents the total number of lower 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVirtualCircuitEthStatsClear 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.5
To clear the statistics for the given virtual circuit, set this object to clear(1)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), none(2)  

wwpLeosVplsVirtualSwitchMplsTable 1.3.6.1.4.1.6141.2.60.28.1.1.20
This table is used to manage virtual switch entries on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsEntry

wwpLeosVplsVirtualSwitchMplsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.20.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchMplsTable table. To create an entry in the table following criteria must be met. Mpls and Ethernet virtual switch name cannot be same but indexes can be - wwpLeosVplsVirtualSwitchMplsVpnId must be specified. - wwpLeosVplsVirtualSwitchMplsType must be specified. - wwpLeosVplsVirtualSwitchMplsName must be specified. - wwpLeosVplsVirtualSwitchMplsStatus must be specified.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsEntry  

wwpLeosVplsVirtualSwitchMplsIndx 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.1
This object specifies the virtual switch index which is used as unique index in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMplsName 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.2
This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later. Mpls and Ethernet virtual switch name cannot be same but indexes can be.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsVirtualSwitchMplsVpnId 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.3
This object specifies the subscriber vlan Id for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

wwpLeosVplsVirtualSwitchMplsEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.4
This object specifies the ingress cos policy for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4)  

wwpLeosVplsVirtualSwitchMplsEncapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.5
This object specifies the ingress fixed cos attributes for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchMplsDecapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.6
This object specifies the egress cos policy for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritVc(2), inheritTunnel(3), leave(4)  

wwpLeosVplsVirtualSwitchMplsDecapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.7
This object specifies the egress cos attributes for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchMplsCtrlProtocolTunnelState 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.8
This object enables or disables control protocol tunneling for a given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchMplsDecapTTLPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.9
This object specifies the TTL policy for a given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pipe(1), uniform(2)  

wwpLeosVplsVirtualSwitchMplsType 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.10
This object specifies the type of virtual switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

wwpLeosVplsVirtualSwitchMplsRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.11
This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMplsMacLrnState 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.12
Setting this object will set the Mac learning state for a given mpls virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchMplsTunnelMethod 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.13
Setting this object will set the tunneling method for a given mpls virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER l2pt(1), transparent(2)  

wwpLeosVplsVirtualSwitchMplsCtrlProtocolDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.14
This object specifies the .1d priority to use when encapsulation control frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchMplsSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.15
Setting this object will configure the policy used to decide whether or not the subscriber frame .1d priorty should be left alone, or remarked to the computed provider priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2)  

wwpLeosVplsVirtualSwitchMplsCtrlProtTransFrameValidate 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.16
Setting this object will set the transparent-mode validate for a given mpls virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchMplsHonorPriority 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.17
Setting this object will select either the c-vlan or s-vlan priority to use through the Virtual Switch and it's associated MPLS Tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER c-vlan(1), s-vlan(2)  

wwpLeosVplsVirtualSwitchMplsMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.21
This table is used to create mpls virtual switch subscriber port-vlan membership entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsMemberEntry

wwpLeosVplsVirtualSwitchMplsMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.21.1
This entry corresponds to single port-vlan subscriber entry in wwpLeosVplsVirtualSwitchMplsMemberTable table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsMemberEntry  

wwpLeosVplsVirtualSwitchMplsMemberPortId 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.1
This object specifies the port number which is to be added as a customer facing port for the mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMplsMemberVlanId 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.2
This object specifies the subscriber vlan attached to this mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. This object cannot be modified one entry is created in this table. This object can only be specified when creating entries in this table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4094  

wwpLeosVplsVirtualSwitchMplsMemberRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.3
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMplsMemberEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.4
This object specifies the ingress cos policy for given member entry. By default 'inheritVs' the encap CoS policy is inherited from the parent virtual-switch settings
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4), inheritVs(5), port-inherit(6)  

wwpLeosVplsVirtualSwitchMplsMemberEncapCosFixedDot1DPri 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.5
This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the member EncapCosPolicy is set to 'fixed'
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchMplsMemberSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.6
This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2), inheritVs(3)  

wwpLeosVplsVirtualSwitchMplsMemberStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.22
The (conceptual) table listing the virtual switch member stats table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsMemberStatsEntry

wwpLeosVplsVirtualSwitchMplsMemberStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.22.1
The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchMplsIndx and wwpLeosVplsVirtualSwitchMplsMemberPortId.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsMemberStatsEntry  

wwpLeosVplsVirtualSwitchMplsMemberRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.22.1.1
This represents the total number of higher 32 bits received for given mpls virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchMplsMemberRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.22.1.2
This represents the total number of lower 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchMplsMemberMeshVcTable 1.3.6.1.4.1.6141.2.60.28.1.1.23
This table is used to create mpls virtual switch mesh-vc membership entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsMemberMeshVcEntry

wwpLeosVplsVirtualSwitchMplsMemberMeshVcEntry 1.3.6.1.4.1.6141.2.60.28.1.1.23.1
This entry corresponds to single mesh-vc entry in wwpLeosVplsVirtualSwitchMplsMemberMeshVcTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsMemberMeshVcEntry  

wwpLeosVplsVirtualSwitchMplsMemberMeshVcMeshVc 1.3.6.1.4.1.6141.2.60.28.1.1.23.1.1
This object specifies the mesh virtual circuit for this mpls virtual switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMplsMemberMeshVcRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.23.1.2
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMplsMemberAcVcTable 1.3.6.1.4.1.6141.2.60.28.1.1.24
This table is used to create mpls virtual switch mesh-vc membership entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsMemberAcVcEntry

wwpLeosVplsVirtualSwitchMplsMemberAcVcEntry 1.3.6.1.4.1.6141.2.60.28.1.1.24.1
This entry corresponds to single mesh-vc entry in wwpLeosVplsVirtualSwitchMplsMemberAcVcTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsMemberAcVcEntry  

wwpLeosVplsVirtualSwitchMplsMemberAcVcAcVc 1.3.6.1.4.1.6141.2.60.28.1.1.24.1.1
This object specifies the attachment virtual circuit for this mpls virtual switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMplsMemberAcVcRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.24.1.2
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsSwitchMplsCtrlProtocolTable 1.3.6.1.4.1.6141.2.60.28.1.1.25
The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsSwitchMplsCtrlProtocolEntry

wwpLeosVplsSwitchMplsCtrlProtocolEntry 1.3.6.1.4.1.6141.2.60.28.1.1.25.1
The layer 2 virtual switch control frame protocol tunnel entry for the Vpls.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsSwitchMplsCtrlProtocolEntry  

wwpLeosVplsSwitchMplsCtrlProtocolNum 1.3.6.1.4.1.6141.2.60.28.1.1.25.1.1
This object represent the list of protocols the device can support.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER l28021x(1), rstp(2), ciscoCdp(3), ciscoDtp(4), ciscoPagp(5), ciscoPvst(6), ciscoUplinkFast(7), ciscoUdlp(8), ciscoVtp(9), gvrp(10), lacp(11), lacpMarker(12), oam(13), lldp(14), vlanBridge(15)  

wwpLeosVplsSwitchMplsCtrlType 1.3.6.1.4.1.6141.2.60.28.1.1.25.1.2
Setting this object to 'discard' will cause wwpLeosVplsSwitchMplsCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchMplsCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchMplsCtrlProtocolNum frame to be tunneled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER discard(1), peer(2), tunnel(3)  

wwpLeosVplsVirtualSwitchEthTable 1.3.6.1.4.1.6141.2.60.28.1.1.26
This table is used to manage virtual switch entries on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthEntry

wwpLeosVplsVirtualSwitchEthEntry 1.3.6.1.4.1.6141.2.60.28.1.1.26.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetTable table. To create an entry in the table following criteria must be met. - wwpLeosVplsVirtualSwitchEthRowStatus must be specified. - wwpLeosVplsVirtualSwitchEthernetName must be specified
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthEntry  

wwpLeosVplsVirtualSwitchEthIndx 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.1
This object specifies the virtual switch index which is used as unique index in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchEthName 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.2
This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later. Mpls and Ethernet virtual switch name cannot be same but indexes can be.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsVirtualSwitchEthVc 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.3
This object specifies the primary virtual circuit ID associated with this virtual switch. To unset it set this to 0. If this object represents PBT virtual circuit then wwpLeosVplsVirtualSwitchEthVcType must also be set to pbt.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

wwpLeosVplsVirtualSwitchEthEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.4
This object specifies the ingress cos policy for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4), port-inherit(5)  

wwpLeosVplsVirtualSwitchEthEncapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.5
This object specifies the ingress fixed cos attributes for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchEthDecapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.6
This object specifies the egress cos policy for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritVc(2), inheritTunnel(3), leave(4)  

wwpLeosVplsVirtualSwitchEthDecapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.7
This object specifies the egress cos attributes for given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchEthCtrlProtocolTunnelState 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.8
This object enables or disables control protocol tunneling for a given virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchEthRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.9
This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchEthMacLrnState 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.10
Setting this object will set the Mac learning state for each ethernet virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchEthTunnelMethod 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.11
Setting this object will set the tunneling method for each ethernet virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER l2pt(1), transparent(2)  

wwpLeosVplsVirtualSwitchEthCtrlProtocolDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.12
This object specifies the .1d priority to use when encapsulation control frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchEthSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.13
Setting this object will configure the policy used to decide whether or not the subscriber frame .1d priorty should be left alone, or remarked to the computed provider priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2)  

wwpLeosVplsVirtualSwitchEthCtrlProtTransFrameValidate 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.14
Setting this object will set the transparent-mode validate for a given eth virtual switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wwpLeosVplsVirtualSwitchEthVcType 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.15
This object specifies the type of vc to be attached to this virtual switch. This object must be set (using SNMP multiple set operation) to pbt type if wwpLeosVplsVirtualSwitchEthVc specifies the pbt vc. Setting only wwpLeosVplsVirtualSwitchEthVcType will return error. Also setting wwpLeosVplsVirtualSwitchEthVcType to none will return error.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), ethernet(2), pbt(3)  

wwpLeosVplsVirtualSwitchEthHonorPriority 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.16
This object specifies which Vlan priority to use on a Virtual Switch. Honor either the c-vlan or the s-vlan priority through the Virtual Switch and it's associated VC or Tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER c-vlan(1), s-vlan(2)  

wwpLeosVplsVirtualSwitchEthDescription 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.17
This object specifies the virtual switch description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

wwpLeosVplsVirtualSwitchEthReservedVlan 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.18
Reserved vlan for the virtual-switch.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..4094  

wwpLeosVplsVirtualSwitchEthMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.27
This table is used to create virtual switch membership entry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthMemberEntry

wwpLeosVplsVirtualSwitchEthMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.27.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetMemberTable table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthMemberEntry  

wwpLeosVplsVirtualSwitchEthMemberPortId 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.1
This object specifies the port id associated with wwpLeosVplsVirtualSwitchEthIndx.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchEthMemberVlan 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.2
This object specifies the subscriber vlan attached to this eth virtual switch index wwpLeosVplsVirtualSwitchEthIndx. This object cannot be modified one entry is created. This object can only be specified when entry is created in this table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4094  

wwpLeosVplsVirtualSwitchEthMemberRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.3
This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchEthMemberEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.4
This object specifies the ingress cos policy for given member entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4), inheritVs(5), port-inherit(6)  

wwpLeosVplsVirtualSwitchEthMemberEncapCosFixedDot1DPri 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.5
This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed'
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchEthMemberSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.6
This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2), inheritVs(3)  

wwpLeosVplsVirtualSwitchEthMemberStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.28
The (conceptual) table listing the virtual switch member stats table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthMemberStatsEntry

wwpLeosVplsVirtualSwitchEthMemberStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.28.1
The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchEthIndx and wwpLeosVplsVirtualSwitchEthMemberPortId.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthMemberStatsEntry  

wwpLeosVplsVirtualSwitchEthMemberRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.28.1.1
This represents the total number of higher 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchEthMemberRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.28.1.2
This represents the total number of lower 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsSwitchEthCtrlProtocolTable 1.3.6.1.4.1.6141.2.60.28.1.1.29
The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsSwitchEthCtrlProtocolEntry

wwpLeosVplsSwitchEthCtrlProtocolEntry 1.3.6.1.4.1.6141.2.60.28.1.1.29.1
The layer 2 virtual switch control frame protocol tunnel entry for the Vpls.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsSwitchEthCtrlProtocolEntry  

wwpLeosVplsSwitchEthCtrlProtocolNum 1.3.6.1.4.1.6141.2.60.28.1.1.29.1.1
This object represent the list of protocols the device can support.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER l28021x(1), rstp(2), ciscoCdp(3), ciscoDtp(4), ciscoPagp(5), ciscoPvst(6), ciscoUplinkFast(7), ciscoUdlp(8), ciscoVtp(9), gvrp(10), lacp(11), lacpMarker(12), oam(13), lldp(14), vlanBridge(15)  

wwpLeosVplsSwitchEthCtrlType 1.3.6.1.4.1.6141.2.60.28.1.1.29.1.2
Setting this object to 'discard' will cause wwpLeosVplsSwitchEthCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchEthCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchEthCtrlProtocolNum frame to be tunneled.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER discard(1), peer(2), tunnel(3)  

wwpLeosVplsVirtualSwitchEtypeTranslationTable 1.3.6.1.4.1.6141.2.60.28.1.1.30
This table controls the global Ethertype translation functions. Only two entries are allowed. Creating more than two entries will return an error. The control is bi-directional. Creating one entry will enable translation as the packet egresses the NNI and as it egresses the UNI port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEtypeTranslationEntry

wwpLeosVplsVirtualSwitchEtypeTranslationEntry 1.3.6.1.4.1.6141.2.60.28.1.1.30.1
Each entry contains the Ethertype being translated and the new Ethertype that will be copied over the old Ethertype.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEtypeTranslationEntry  

wwpLeosVplsVirtualSwitchEtypeTranslationOriginalEtype 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.1
This object represent the original Ethertype of the frame.
Status: current Access: read-only
OBJECT-TYPE    
  EtherType  

wwpLeosVplsVirtualSwitchEtypeTranslationMappedEtype 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.2
This object represent the Ethertype that will be stamped on the frame on egress and removed on ingress.
Status: current Access: read-create
OBJECT-TYPE    
  EtherType  

wwpLeosVplsVirtualSwitchEtypeTranslationRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.3
This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsTunnelPairTable 1.3.6.1.4.1.6141.2.60.28.1.1.31
This table allows creating tunnel pairs. Having a tunnel pair will force the device to accept pbt encapsulated frames on given pair of tunnels ports and not on any port. This table is only accessible in PBT mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsTunnelPairEntry

wwpLeosVplsTunnelPairEntry 1.3.6.1.4.1.6141.2.60.28.1.1.31.1
Each entry contains the tunnel pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsTunnelPairEntry  

wwpLeosVplsTunnelPairIndx 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.1
This object represent the index in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsTunnelPairName 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.2
This object represent the name of the pair and must be unique. This object cannot be modified once entry is created.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

wwpLeosVplsTunnelPairEncapTunnelIndx 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.3
This object represent the encap tunnel that is part of this tunnel pair. This tunnel index should be valid and must exist in wwpLeosVplsEncapTunnelTable. This object cannot be modified once entry is created.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsTunnelPairDecapTunnelIndx 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.4
This object represent the decap tunnel that is part of this tunnel pair. This tunnel index should be valid and must exist in wwpLeosVplsDecapTunnelTable. This object cannot be modified once entry is created.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

wwpLeosVplsTunnelPairRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.5
This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMplsEvplMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.32
This table is used to create mpls virtual switch subscriber port-vlan membership entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsEvplMemberEntry

wwpLeosVplsVirtualSwitchMplsEvplMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.32.1
This entry corresponds to single port-vlan subscriber entry in wwpLeosVplsVirtualSwitchMplsEvplMemberTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsEvplMemberEntry  

wwpLeosVplsVirtualSwitchMplsEvplMemberPortId 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.1
This object specifies the port number which is to be added as a customer facing port for the mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchMplsEvplMemberVlanId 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.2
This object specifies the subscriber vlan attached to this mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. This object cannot be modified once entry is created in this table. This object can only be specified when creating entries in this table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4094  

wwpLeosVplsVirtualSwitchMplsEvplMemberRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.3
Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchMplsEvplMemberEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.4
This object specifies the ingress cos policy for given EVPL entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4), inheritVs(5), port-inherit(6)  

wwpLeosVplsVirtualSwitchMplsEvplMemberEncapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.5
This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed'
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchMplsEvplMemberSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.6
This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2), inheritVs(3)  

wwpLeosVplsVirtualSwitchMplsEvplMemberStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.33
The (conceptual) table listing the virtual switch member stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchMplsEvplMemberStatsEntry

wwpLeosVplsVirtualSwitchMplsEvplMemberStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.33.1
The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchMplsIndx, wwpLeosVplsVirtualSwitchMplsMemberPortId and VlanId.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchMplsEvplMemberStatsEntry  

wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.33.1.1
This represents the total number of higher 32 bits received for given mpls virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.33.1.2
This represents the total number of lower 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchEthEvplMemberTable 1.3.6.1.4.1.6141.2.60.28.1.1.34
This table is used to create virtual switch membership entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthEvplMemberEntry

wwpLeosVplsVirtualSwitchEthEvplMemberEntry 1.3.6.1.4.1.6141.2.60.28.1.1.34.1
This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetEvplMemberTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthEvplMemberEntry  

wwpLeosVplsVirtualSwitchEthEvplMemberPortId 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.1
This object specifies the port id associated with wwpLeosVplsVirtualSwitchEthIndx.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchEthEvplMemberVlan 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.2
This object specifies the subscriber vlan attached to this eth virtual switch index wwpLeosVplsVirtualSwitchEthIndx. This object cannot be modified one entry is created. This object can only be specified when entry is created in this table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..4095  

wwpLeosVplsVirtualSwitchEthEvplMemberRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.3
This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchEthEvplMemberEncapCosPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.4
This object specifies the ingress cos policy for given EVPL entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), inheritDot1dPri(2), inheritIpPrec(3), inheritPhbg(4), inheritVs(5), port-inherit(6)  

wwpLeosVplsVirtualSwitchEthEvplMemberEncapFixedDot1dPri 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.5
This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed'
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

wwpLeosVplsVirtualSwitchEthEvplMemberSubscriberDot1dPolicy 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.6
This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leave(1), provider-inherit(2), inheritVs(3)  

wwpLeosVplsVirtualSwitchEthEvplMemberTranslateTag 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.7
Subscriber VLAN translate stamp.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..4094  

wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.8
This object specifies the service VLAN TPID.It is currently only applicable for VS instances associated with an MPLS enabled VS
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tpid8100(1), tpid9100(2), tpid88A8(3), none(99)  

wwpLeosVplsVirtualSwitchEthEvplMemberStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.35
The (conceptual) table listing the virtual switch member stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthEvplMemberStatsEntry

wwpLeosVplsVirtualSwitchEthEvplMemberStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.35.1
The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchEthIndx, wwpLeosVplsVirtualSwitchEthMemberPortId and VlanId.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthEvplMemberStatsEntry  

wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.35.1.1
This represents the total number of higher 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.35.1.2
This represents the total number of lower 32 bits received for given virtual switch member port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTotalStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.36
The (conceptual) table listing the virtual circuit stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitEthTotalStatsEntry

wwpLeosVplsVirtualCircuitEthTotalStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.36.1
The ethernet virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitEthTotalStatsEntry  

wwpLeosVplsVirtualCircuitEthTotalTxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.1
This represents the total number of higher 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTotalTxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.2
This represents the total number of lower 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTotalRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.3
This represents the total number of higher 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitEthTotalRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.4
This represents the total number of lower 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsTotalStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.37
The (conceptual) table listing the mpls virtual circuit stats table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualCircuitMplsTotalStatsEntry

wwpLeosVplsVirtualCircuitMplsTotalStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.37.1
The mpls virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsTotalIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualCircuitMplsTotalStatsEntry  

wwpLeosVplsVirtualCircuitMplsTotalTxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.1
This represents the total number of higher 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsTotalTxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.2
This represents the total number of lower 32 bits transmitted for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsTotalRxBytesHi 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.3
This represents the total number of higher 32 bits received for given mpls virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualCircuitMplsTotalRxBytesLo 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.4
This represents the total number of lower 32 bits received for given virtual circuit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchEthL2CftProtocolTable 1.3.6.1.4.1.6141.2.60.28.1.1.49
Table of Virtual Switch L2 CFT protocols.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchEthL2CftProtocolEntry

wwpLeosVplsVirtualSwitchEthL2CftProtocolEntry 1.3.6.1.4.1.6141.2.60.28.1.1.49.1
Virtual Switch L2CFT protocol entry in the Virtual Switch L2CFT Protocol Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchEthL2CftProtocolEntry  

wwpLeosVplsVirtualSwitchEthL2CftProtocolType 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.1
This object specifies a unique protocol type-index into the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER ciscoCdp(1), ciscoDtp(2), ciscoPagp(3), ciscoUdld(4), ciscoVtp(5), ciscoPvst(6), ciscoStpUplinkFast(7), vlanBridge(8), rstp(9), lacp(10), lacpMarker(11), oam(12), lldp(13), i8021x(14), gmrp(15), gvrp(16), brigeBlock(32), allBridgesBlock(33), garpBlock(34), unknown(99)  

wwpLeosVplsVirtualSwitchEthL2CftProtocolDisposition 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.2
This object specifies the virtual switch L2 CFT protocol action. May forward or drop frames that match this protocol at the virtual switch + RLAN layer
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER forward(1), discard(2)  

wwpLeosVplsVirtualSwitchEthL2CftProtocolRowStatus 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.64
To create a row in this table, a manager must set this object to 'createAndGo'. To delete the entry set this to destroy. To update this entry this object may not be set.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wwpLeosVplsVirtualSwitchCFTProtoStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.50
The (conceptual) table listing the l2 control frame protocol stats for a given vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchCFTProtoStatsEntry

wwpLeosVplsVirtualSwitchCFTProtoStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.50.1
The layer 2 control frame protocol stats entry for the vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchCFTProtoStatsEntry  

wwpLeosVplsVirtualSwitchCFTProtoStatsEntryVirtualSwitchIndx 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.1
This object specifies the virtual switch index which is used as unique index in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchCFTProtol2RxPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.2
Specifies number of packets ingressed matching protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2TunneledPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.3
Specifies the number of packets that were made tunneled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2PeerPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.4
Specifies the number of peered packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2DiscardedPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.5
Specifies the number of discarded packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2DecodedPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.6
Specifies the number of packets that came in tunneled and then restored.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2DecodedFailures 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.7
Specifies the number of packets that failed to 'untunnel'.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2TunneledSubcriberPortPkts 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.8
Specifies the number of tunneled packets received on subscriber port..
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtol2ProtocolNum 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.9
This object represent the list of protocols supported by the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER l28021x(1), rstp(2), ciscoCdp(3), ciscoDtp(4), ciscoPagp(5), ciscoPvst(6), ciscoUplinkFast(7), ciscoUdlp(8), ciscoVtp(9), gvrp(10), lacp(11), lacpMarker(12), lldp(13), oam(14), vlanBridge(15)  

wwpLeosVplsVirtualSwitchCFTProtoTotalStatsTable 1.3.6.1.4.1.6141.2.60.28.1.1.51
The (conceptual) table listing the l2 control frame protocol stats for a given vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntry

wwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntry 1.3.6.1.4.1.6141.2.60.28.1.1.51.1
The layer 2 control frame protocol stats entry for the vlan.
Status: current Access: not-accessible
OBJECT-TYPE    
  WwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntry  

wwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntryVirtualSwitchIndx 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.1
This object specifies the virtual switch index which is used as unique index in the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wwpLeosVplsVirtualSwitchCFTProtoTotall2RxPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.2
Specifies number of packets ingressed matching protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.3
Specifies the number of packets that were made tunneled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2PeerPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.4
Specifies the number of peered packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2DiscardedPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.5
Specifies the number of discarded packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.6
Specifies the number of packets that came in tunneled and then restored.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedFailures 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.7
Specifies the number of packets that failed to 'untunnel'.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledSubcriberPortPkts 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.8
Specifies the number of tunneled packets received on subscriber port..
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wwpLeosVplsVirtualSwitchCFTProtoTotall2ProtocolNum 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.9
This object represent the list of protocols supported by the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER l28021x(1), rstp(2), ciscoCdp(3), ciscoDtp(4), ciscoPagp(5), ciscoPvst(6), ciscoUplinkFast(7), ciscoUdlp(8), ciscoVtp(9), gvrp(10), lacp(11), lacpMarker(12), lldp(13), oam(14), vlanBridge(15)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor