Wellfleet-CONSOLE-MIB

File: Wellfleet-CONSOLE-MIB.mib (23645 bytes)

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

Counter	OBJECT-TYPE	DisplayString
wfSerialPortGroup	wfServices

Defined Types

WfSerialPortEntry
SEQUENCE
	wfSerialPortDelete	INTEGER
	wfSerialPortDisable	INTEGER
	wfSerialPortState	INTEGER
	wfSerialPortNumber	INTEGER
	wfSerialPortName	DisplayString
	wfSerialPortSlot	INTEGER
	wfSerialPortType	INTEGER
	wfSerialPortBaudRate	INTEGER
	wfSerialPortDataBits	INTEGER
	wfSerialPortParity	INTEGER
	wfSerialPortStopBits	INTEGER
	wfSerialPortModemEnable	INTEGER
	wfSerialPortLinesPerScreen	INTEGER
	wfSerialPortMoreEnable	INTEGER
	wfSerialPortPrompt	DisplayString
	wfSerialPortLoginTimeOut	INTEGER
	wfSerialPortPasswordTimeOut	INTEGER
	wfSerialPortCommandTimeOut	INTEGER
	wfSerialPortLoginRetries	INTEGER
	wfSerialPortTotalLogins	Counter
	wfSerialPortUserLoginErrors	Counter
	wfSerialPortManagerLoginErrors	Counter
	wfSerialPortOtherLoginErrors	Counter
	wfSerialPortTtyFrameErrors	Counter
	wfSerialPortTtyOverrunErrors	Counter
	wfSerialPortTtyParityErrors	Counter
	wfSerialPortTtyInfifoErrors	Counter
	wfSerialPortInitialSearchPath	DisplayString
	wfSerialPortManagerAutoScript	DisplayString
	wfSerialPortUserAutoScript	DisplayString
	wfSerialPortUserAbortLogoutDisable	INTEGER
	wfSerialPortHistoryDepth	INTEGER
	wfSerialPortAutoSaveNumFiles	INTEGER
	wfSerialPortAutoSaveVolume	DisplayString
	wfSerialPortModemIdSwRev	DisplayString
	wfSerialPortModemIdHwRev	DisplayString
	wfSerialPortModemLineState	INTEGER
	wfSerialPortModemCfgFactoryDefaults	INTEGER
	wfSerialPortModemCfgInitString	DisplayString
	wfSerialPortModemCfgDefaultString	DisplayString
	wfSerialPortModemCfgResultCodeString	DisplayString
	wfSerialPortModemCfgState	INTEGER
	wfSerialPortModemCfgCountry	INTEGER
	wfSerialPortModemInitState	INTEGER

Defined Values

wfConsole		1.3.6.1.4.1.18.3.3.2.1
OBJECT IDENTIFIER

wfBaudRate		1.3.6.1.4.1.18.3.3.2.1.1
Baud rate configured on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER

wfDataBits		1.3.6.1.4.1.18.3.3.2.1.2
Number of data bits configured on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER

wfParity		1.3.6.1.4.1.18.3.3.2.1.3
Type of parity configured on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), odd(2), even(3)

wfStopBits		1.3.6.1.4.1.18.3.3.2.1.4
Number of stop bits configured on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	s1bit(1), s15bit(2), s2bit(3)

wfModemEnable		1.3.6.1.4.1.18.3.3.2.1.5
Enable the Technician Interface console to run over a modem
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfLinesPerScreen		1.3.6.1.4.1.18.3.3.2.1.6
Number of lines which can be displayed in one screen on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER

wfMoreEnable		1.3.6.1.4.1.18.3.3.2.1.7
Enable the 'more' feature on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfPrompt		1.3.6.1.4.1.18.3.3.2.1.8
Character string which will be used as the system prompt on the Technician Interface console
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString

wfLoginTimeOut		1.3.6.1.4.1.18.3.3.2.1.9
IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfPasswordTimeOut		1.3.6.1.4.1.18.3.3.2.1.10
Timout on Password entry
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfCommandTimeOut		1.3.6.1.4.1.18.3.3.2.1.11
IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfLoginRetries		1.3.6.1.4.1.18.3.3.2.1.12
IF MODEM_ENABLED then limit # of login attempts then HUP
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfTotalLogins		1.3.6.1.4.1.18.3.3.2.1.13
Total number of TI login attempts
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfUserLoginErrors		1.3.6.1.4.1.18.3.3.2.1.14
Total number of FAILED User login attempts
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfManagerLoginErrors		1.3.6.1.4.1.18.3.3.2.1.15
Total number of FAILED Manager login attempts
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfOtherLoginErrors		1.3.6.1.4.1.18.3.3.2.1.16
Total number of FAILED Other login attempts
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfTtyFrameErrors		1.3.6.1.4.1.18.3.3.2.1.17
Count of TTY Frame errors
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfTtyOverrunErrors		1.3.6.1.4.1.18.3.3.2.1.18
Count of TTY Overrun errors
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfTtyParityErrors		1.3.6.1.4.1.18.3.3.2.1.19
Count of TTY Parity errors
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfTtyInfifoErrors		1.3.6.1.4.1.18.3.3.2.1.20
Count of TTY Input Fifo errors
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortTable		1.3.6.1.4.1.18.3.3.2.11.1
Configuration of system serial port(s)
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfSerialPortEntry

wfSerialPortEntry		1.3.6.1.4.1.18.3.3.2.11.1.1
Information for each serial port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfSerialPortEntry

wfSerialPortDelete		1.3.6.1.4.1.18.3.3.2.11.1.1.1
Flag to indicate Serial Port instance deletion
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfSerialPortDisable		1.3.6.1.4.1.18.3.3.2.11.1.1.2
Enable or disable this Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfSerialPortState		1.3.6.1.4.1.18.3.3.2.11.1.1.3
The state of this Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), notpresent(4)

wfSerialPortNumber		1.3.6.1.4.1.18.3.3.2.11.1.1.4
Serial Port number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfSerialPortName		1.3.6.1.4.1.18.3.3.2.11.1.1.5
Serial Port name
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

wfSerialPortSlot		1.3.6.1.4.1.18.3.3.2.11.1.1.6
Slot number of Serial Port session
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfSerialPortType		1.3.6.1.4.1.18.3.3.2.11.1.1.7
Type of Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ti(1), printer(2), rtelnet(3)

wfSerialPortBaudRate		1.3.6.1.4.1.18.3.3.2.11.1.1.8
Baud rate configured on this Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfSerialPortDataBits		1.3.6.1.4.1.18.3.3.2.11.1.1.9
Number of data bits configured on this Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfSerialPortParity		1.3.6.1.4.1.18.3.3.2.11.1.1.10
Type of parity configured on this Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), odd(2), even(3)

wfSerialPortStopBits		1.3.6.1.4.1.18.3.3.2.11.1.1.11
Number of stop bits configured on this Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	s1bit(1), s15bit(2), s2bit(3)

wfSerialPortModemEnable		1.3.6.1.4.1.18.3.3.2.11.1.1.12
Enable the Serial Port to run with modem leads enabled
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfSerialPortLinesPerScreen		1.3.6.1.4.1.18.3.3.2.11.1.1.13
Number of lines which can be displayed in one screen on the Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfSerialPortMoreEnable		1.3.6.1.4.1.18.3.3.2.11.1.1.14
Enable the 'more' feature on the Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfSerialPortPrompt		1.3.6.1.4.1.18.3.3.2.11.1.1.15
Character string which will be used as the system prompt on the Serial Port
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortLoginTimeOut		1.3.6.1.4.1.18.3.3.2.11.1.1.16
IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfSerialPortPasswordTimeOut		1.3.6.1.4.1.18.3.3.2.11.1.1.17
Timout on Password entry
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfSerialPortCommandTimeOut		1.3.6.1.4.1.18.3.3.2.11.1.1.18
IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfSerialPortLoginRetries		1.3.6.1.4.1.18.3.3.2.11.1.1.19
IF MODEM_ENABLED then limit # of login attempts then HUP
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..99

wfSerialPortTotalLogins		1.3.6.1.4.1.18.3.3.2.11.1.1.20
Total number of TI login attempts on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortUserLoginErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.21
Total number of FAILED User login attempts on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortManagerLoginErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.22
Total number of FAILED Manager login attempts on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortOtherLoginErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.23
Total number of FAILED Other login attempts on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortTtyFrameErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.24
Count of TTY Frame errors on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortTtyOverrunErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.25
Count of TTY Overrun errors on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortTtyParityErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.26
Count of TTY Parity errors on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortTtyInfifoErrors		1.3.6.1.4.1.18.3.3.2.11.1.1.27
Count of TTY Input Fifo errors on Serial Port
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfSerialPortInitialSearchPath		1.3.6.1.4.1.18.3.3.2.11.1.1.28
Example: 'A:;1:;2:' or '2:;4:6:;9:
Status: obsolete	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortManagerAutoScript		1.3.6.1.4.1.18.3.3.2.11.1.1.29
for each login.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortUserAutoScript		1.3.6.1.4.1.18.3.3.2.11.1.1.30
for each login.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortUserAbortLogoutDisable		1.3.6.1.4.1.18.3.3.2.11.1.1.31
a USER from escaping out of the User Autoscript
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfSerialPortHistoryDepth		1.3.6.1.4.1.18.3.3.2.11.1.1.32
TI command history table size
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..40

wfSerialPortAutoSaveNumFiles		1.3.6.1.4.1.18.3.3.2.11.1.1.33
Number of times AutoSave will save the log 0 - disable the AutoSave log
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..99

wfSerialPortAutoSaveVolume		1.3.6.1.4.1.18.3.3.2.11.1.1.34
Volume, to which AutoSave will save logs Example: 'A:' or '2:'
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortModemIdSwRev		1.3.6.1.4.1.18.3.3.2.11.1.1.35
A textual description of the modem's firmware version number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..79)

wfSerialPortModemIdHwRev		1.3.6.1.4.1.18.3.3.2.11.1.1.36
A textual description of the revision number of the modem daughter card.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..79)

wfSerialPortModemLineState		1.3.6.1.4.1.18.3.3.2.11.1.1.37
Indicates the state of the modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), onHook(2), offHook(3), connected(4), busiedOut(5), reset(6)

wfSerialPortModemCfgFactoryDefaults		1.3.6.1.4.1.18.3.3.2.11.1.1.38
This object indicates if factory defaults are to be loaded. If set to enabled(1), factory defaults are loaded. If set to disabled(2), the initialization string in wfModemCfgInitString is not sent to the modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfSerialPortModemCfgInitString		1.3.6.1.4.1.18.3.3.2.11.1.1.39
An initialization string that will be sent to the modem each time the modem is rebooted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfSerialPortModemCfgDefaultString		1.3.6.1.4.1.18.3.3.2.11.1.1.40
The string contains AT comands for initializing the modem every time the modem comes up, regardless of configuration.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

wfSerialPortModemCfgResultCodeString		1.3.6.1.4.1.18.3.3.2.11.1.1.41
The ASCII response string returned by the modem. Response strings will be returned in response to last command to the modem and in response to activity on the line.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

wfSerialPortModemCfgState		1.3.6.1.4.1.18.3.3.2.11.1.1.42
Indicates the state of AT command processing. When a new initialization string is to be sent to the modem, the sender sets the state to cfgInProgress(2). After the command has been sent to the modem, and a result code has been returned, the state is set to cfgResponseReturned(3). Once the sender has received the return code, the sender sets the state to cfgIdle(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	cfgIdle(1), cfgInProgress(2), cfgResponseReturned(3)

wfSerialPortModemCfgCountry		1.3.6.1.4.1.18.3.3.2.11.1.1.43
Identifies the country the modem is designed to operate in. This object is not read from the modem directly. It must be entered manually when configuring the modem.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	northAmerica(1), japan(2), uk(3), germany(4)

wfSerialPortModemInitState		1.3.6.1.4.1.18.3.3.2.11.1.1.44
Indictes the state of the modem initialization sequence. The state will freeze in the state that fails when a failure is detected. Otherwise, the state will be set to initComplete when initialization completes successfully. The state number correspond to those for the COM port modems. Some of the states are not valid for the console modem.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	startup(1), getInfo(3), setDefaults(4), initialization(5), initComplete(8)