Wellfleet-DS1E1-MIB

File: Wellfleet-DS1E1-MIB.mib (229460 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

Counter Gauge TimeTicks
OBJECT-TYPE DisplayString wfMcT1Group
wfDs1E1Group

Defined Types

WfDs1E1ModuleEntry  
SEQUENCE    
  wfDs1E1ModuleDelete INTEGER
  wfDs1E1ModuleSlot INTEGER
  wfDs1E1ModuleModule INTEGER
  wfDs1E1ModulePrimaryClock INTEGER
  wfDs1E1ModuleSecondaryClock INTEGER
  wfDs1E1ModuleCurrentClock INTEGER
  wfDs1E1ModuleExtClockOperational INTEGER
  wfDs1E1ModuleLoop1ClockOperational INTEGER
  wfDs1E1ModuleLoop2ClockOperational INTEGER
  wfDs1E1ModuleLoop3ClockOperational INTEGER
  wfDs1E1ModuleLoop4ClockOperational INTEGER
  wfDs1E1ModuleCfgTxBufferUseCredits INTEGER
  wfDs1E1ModuleCfgRxBufferUseCredits INTEGER
  wfDs1E1ModuleTxBufferUseCredits INTEGER
  wfDs1E1ModuleRxBufferUseCredits INTEGER

WfDs1E1PortMapEntry  
SEQUENCE    
  wfDs1E1PortMapDelete INTEGER
  wfDs1E1PortMapSlot INTEGER
  wfDs1E1PortMapConnector INTEGER
  wfDs1E1PortMapLineNumber INTEGER
  wfDs1E1PortMapDslId INTEGER

WfDs1E1PortEntry  
SEQUENCE    
  wfDs1E1PortDelete INTEGER
  wfDs1E1PortDisable INTEGER
  wfDs1E1PortState INTEGER
  wfDs1E1PortLineNumber INTEGER
  wfDs1E1PortMtu INTEGER
  wfDs1E1PortSignalLevel INTEGER
  wfDs1E1PortSetupAlarmThreshold INTEGER
  wfDs1E1PortClearAlarmThreshold INTEGER
  wfDs1E1PortFdlTargetHdlcAddress INTEGER
  wfDs1E1PortAcceptLoopbackRequest INTEGER
  wfDs1E1PortLoopbackState INTEGER
  wfDs1E1PortBertMode INTEGER
  wfDs1E1PortBertTestPattern INTEGER
  wfDs1E1PortBertSendAlarm INTEGER
  wfDs1E1PortInternationalBit INTEGER
  wfDs1E1PortLineApplication INTEGER
  wfDs1E1PortLoggingEnableMask INTEGER
  wfDs1E1PortSendPrmCrAddressBit INTEGER
  wfDs1E1PortAcceptPrmCrAddressBit INTEGER
  wfDs1E1PortLineImpedanceOption INTEGER
  wfDs1E1PortFdlLoopInterframeFill INTEGER
  wfDs1E1PortRelayCtrl INTEGER
  wfDs1E1PortRelayStatus INTEGER
  wfDs1E1PortPrimaryClockSource INTEGER
  wfDs1E1PortSecondaryClockSource INTEGER
  wfDs1E1PortCurrentClock INTEGER
  wfDs1E1PortExtClockOperational INTEGER
  wfDs1E1PortTransmitWaveform INTEGER

WfDs1E1ConfigEntry  
SEQUENCE    
  wfDs1E1ConfigDelete INTEGER
  wfDs1E1ConfigPortLineNumber INTEGER
  wfDs1E1ConfigIfIndex INTEGER
  wfDs1E1ConfigTimeElapsed INTEGER
  wfDs1E1ConfigValidIntervals INTEGER
  wfDs1E1ConfigLineType INTEGER
  wfDs1E1ConfigLineCoding INTEGER
  wfDs1E1ConfigSendCode INTEGER
  wfDs1E1ConfigCircuitIdentifier DisplayString
  wfDs1E1ConfigLoopbackConfig INTEGER
  wfDs1E1ConfigLineStatus INTEGER
  wfDs1E1ConfigSignalMode INTEGER
  wfDs1E1ConfigTransmitClockSource INTEGER
  wfDs1E1ConfigFdl INTEGER

WfDs1E1ActionEntry  
SEQUENCE    
  wfDs1E1ActionPortLineNumber INTEGER
  wfDs1E1ActionBertReset INTEGER
  wfDs1E1ActionBertErrorInsert INTEGER
  wfDs1E1ActionSendLoopCode INTEGER
  wfDs1E1ActionSendFdlLoopbackCode INTEGER
  wfDs1E1ActionSendLoopUpFractionalCode INTEGER
  wfDs1E1ActionSendLoopDownFractionalCode INTEGER
  wfDs1E1ActionClearFractionalLoopState INTEGER
  wfDs1E1ActionClearFdlStats INTEGER
  wfDs1E1ActionClearCurrentStats INTEGER
  wfDs1E1ActionClearFarEndCurrentStats INTEGER
  wfDs1E1ActionClearDayCurrentStats INTEGER
  wfDs1E1ActionClearFarEndDayCurrentStats INTEGER
  wfDs1E1ActionClearIntervalStats INTEGER
  wfDs1E1ActionClearFarEndIntervalStats INTEGER

WfLogicalLineEntry  
SEQUENCE    
  wfLogicalLineDelete INTEGER
  wfLogicalLineDisable INTEGER
  wfLogicalLineState INTEGER
  wfLogicalLinePortLineNumber INTEGER
  wfLogicalLineIndex INTEGER
  wfLogicalLineCct INTEGER
  wfLogicalLineLineNumber INTEGER
  wfLogicalLineBofl INTEGER
  wfLogicalLineBoflTmo INTEGER
  wfLogicalLineFractionalLoopback INTEGER
  wfLogicalLineTimeSlotAssignment DisplayString
  wfLogicalLineMtu INTEGER
  wfLogicalLineMadr OCTET STRING
  wfLogicalLineWanProtocol INTEGER
  wfLogicalLineHdlcService INTEGER
  wfLogicalLineLocalHdlcAddress INTEGER
  wfLogicalLineRemoteHdlcAddress INTEGER
  wfLogicalLineRateAdaption INTEGER
  wfLogicalLineIFTF INTEGER
  wfLogicalLineCRCSize INTEGER
  wfLogicalLineRxOctets Counter
  wfLogicalLineRxFrames Counter
  wfLogicalLineTxOctets Counter
  wfLogicalLineTxFrames Counter
  wfLogicalLineRxErrors Counter
  wfLogicalLineTxErrors Counter
  wfLogicalLineLackRxResources Counter
  wfLogicalLineLackTxResources Counter
  wfLogicalLineTxUnderflows Counter
  wfLogicalLineRxOverflows Counter
  wfLogicalLineRxNullFrames Counter
  wfLogicalLineRxShortFrames Counter
  wfLogicalLineRxLossSyncs Counter
  wfLogicalLineRxCRCErrors Counter
  wfLogicalLineRxNonOctetBits Counter
  wfLogicalLineRxLongFrames Counter
  wfLogicalLineRxAbortFrames Counter
  wfLogicalLineRxDescOverflows Counter
  wfLogicalLineRxReplenMisses Counter
  wfLogicalLineRxIFCs Counter
  wfLogicalLineRxDropPackets Counter
  wfLogicalLineCfgTxQueueLength INTEGER
  wfLogicalLineCfgRxQueueLength INTEGER
  wfLogicalLineTxQueueLength INTEGER
  wfLogicalLineRxQueueLength INTEGER
  wfLogicalLineTxQueueEmpties Counter
  wfLogicalLineRxIntProcs Counter
  wfLogicalLineTxIntProcs Counter
  wfLogicalLineRxPktCorruptions Counter
  wfLogicalLineTurboBofl INTEGER
  wfLogicalLineBoflNum INTEGER
  wfLogicalLineBoflLen INTEGER
  wfLogicalLineOutQLen Gauge
  wfLogicalLineLastChange TimeTicks
  wfLogicalLineCfgMtu INTEGER
  wfLogicalLineRemoteLpbkDetection INTEGER
  wfLogicalLineLastState INTEGER
  wfLogicalLineRxIdles Counter
  wfLogicalLineRole INTEGER
  wfLogicalLineActiveCct INTEGER
  wfLogicalLineActualRateAdaption INTEGER
  wfLogicalLineBertMode INTEGER
  wfLogicalLineBertTestPattern INTEGER
  wfLogicalLineAcceptFracLoopCode INTEGER
  wfLogicalLineDS0AStatus INTEGER
  wfLogicalLineNRZIEnable INTEGER
  wfLogicalLineNRZIType INTEGER

WfDs1E1FracEntry  
SEQUENCE    
  wfDs1E1FracDelete INTEGER
  wfDs1E1FracPortLineNumber INTEGER
  wfDs1E1FracNumber INTEGER
  wfDs1E1FracLogicalLineIndex INTEGER
  wfDs1E1FracActualLogicalLineIndex INTEGER

WfDs1E1CurrentEntry  
SEQUENCE    
  wfDs1E1CurrentPortLineNumber INTEGER
  wfDs1E1CurrentESs Gauge
  wfDs1E1CurrentSESs Gauge
  wfDs1E1CurrentSEFSs Gauge
  wfDs1E1CurrentUASs Gauge
  wfDs1E1CurrentCSSs Gauge
  wfDs1E1CurrentPCVs Gauge
  wfDs1E1CurrentLESs Gauge
  wfDs1E1CurrentBESs Gauge
  wfDs1E1CurrentDMs Gauge
  wfDs1E1CurrentLCVs Gauge
  wfDs1E1CurrentSASs Gauge
  wfDs1E1CurrentAISSs Gauge
  wfDs1E1CurrentFCs Gauge
  wfDs1E1CurrentTimeElapsed INTEGER
  wfDs1E1CurrentValidIntervals INTEGER
  wfDs1E1CurrentValidFlag INTEGER

WfDs1E1IntervalEntry  
SEQUENCE    
  wfDs1E1IntervalPortLineNumber INTEGER
  wfDs1E1IntervalNumber INTEGER
  wfDs1E1IntervalESs Gauge
  wfDs1E1IntervalSESs Gauge
  wfDs1E1IntervalSEFSs Gauge
  wfDs1E1IntervalUASs Gauge
  wfDs1E1IntervalCSSs Gauge
  wfDs1E1IntervalPCVs Gauge
  wfDs1E1IntervalLESs Gauge
  wfDs1E1IntervalBESs Gauge
  wfDs1E1IntervalDMs Gauge
  wfDs1E1IntervalLCVs Gauge
  wfDs1E1IntervalSASs Gauge
  wfDs1E1IntervalAISSs Gauge
  wfDs1E1IntervalFCs Gauge
  wfDs1E1IntervalValidFlag INTEGER

WfDs1E1TotalEntry  
SEQUENCE    
  wfDs1E1TotalPortLineNumber INTEGER
  wfDs1E1TotalESs Gauge
  wfDs1E1TotalSESs Gauge
  wfDs1E1TotalSEFSs Gauge
  wfDs1E1TotalUASs Gauge
  wfDs1E1TotalCSSs Gauge
  wfDs1E1TotalPCVs Gauge
  wfDs1E1TotalLESs Gauge
  wfDs1E1TotalBESs Gauge
  wfDs1E1TotalDMs Gauge
  wfDs1E1TotalLCVs Gauge
  wfDs1E1TotalSASs Gauge
  wfDs1E1TotalAISSs Gauge
  wfDs1E1TotalFCs Gauge
  wfDs1E1TotalValidFlag INTEGER

WfDs1E1AnsiEntry  
SEQUENCE    
  wfDs1E1AnsiPortLineNumber INTEGER
  wfDs1E1AnsiCRCCounts Counter
  wfDs1E1AnsiBPVCounts Counter
  wfDs1E1AnsiOOFCounts Counter
  wfDs1E1AnsiFECounts Counter
  wfDs1E1AnsiESCounts Counter
  wfDs1E1AnsiSESCounts Counter
  wfDs1E1AnsiUASCounts Counter
  wfDs1E1AnsiPRMR0Counts Counter
  wfDs1E1AnsiPRMR1Counts Counter
  wfDs1E1AnsiPRMR2Counts Counter
  wfDs1E1AnsiPRMR3Counts Counter
  wfDs1E1AnsiPRMESCounts Counter
  wfDs1E1AnsiPRMSESCounts Counter
  wfDs1E1AnsiPRMECounts Counter

WfDs1E1BertStatsEntry  
SEQUENCE    
  wfDs1E1BertStatsPortLineNumber INTEGER
  wfDs1E1BertStatsBitErrors Counter
  wfDs1E1BertStatsBits Counter

WfDs1E1CurrentFramerStatsEntry  
SEQUENCE    
  wfDs1E1CurrentFramerStatsPortLineNumber INTEGER
  wfDs1E1CurrentFramerStatsMediaType INTEGER
  wfDs1E1CurrentFramerStatsBpvCounts Gauge
  wfDs1E1CurrentFramerStatsCrc4Counts Gauge
  wfDs1E1CurrentFramerStatsFebeCounts Gauge
  wfDs1E1CurrentFramerStatsOofCounts Gauge
  wfDs1E1CurrentFramerStatsFeCounts Gauge
  wfDs1E1CurrentFramerStatsLossFrameFailures Gauge
  wfDs1E1CurrentFramerStatsLossSignalFailures Gauge
  wfDs1E1CurrentFramerStatsAlarmIndicationFailures Gauge
  wfDs1E1CurrentFramerStatsRemoteAlarmFailures Gauge

WfDs1E1TotalFramerStatsEntry  
SEQUENCE    
  wfDs1E1TotalFramerStatsPortLineNumber INTEGER
  wfDs1E1TotalFramerStatsMediaType INTEGER
  wfDs1E1TotalFramerStatsValidIntervals Gauge
  wfDs1E1TotalFramerStatsBpvCounts Gauge
  wfDs1E1TotalFramerStatsCrc4Counts Gauge
  wfDs1E1TotalFramerStatsFebeCounts Gauge
  wfDs1E1TotalFramerStatsOofCounts Gauge
  wfDs1E1TotalFramerStatsFeCounts Gauge
  wfDs1E1TotalFramerStatsLossFrameFailures Gauge
  wfDs1E1TotalFramerStatsLossSignalFailures Gauge
  wfDs1E1TotalFramerStatsAlarmIndicationFailures Gauge
  wfDs1E1TotalFramerStatsRemoteAlarmFailures Gauge

WfDs1E1IntervalFramerStatsEntry  
SEQUENCE    
  wfDs1E1IntervalFramerStatsPortLineNumber INTEGER
  wfDs1E1IntervalFramerStatsIntervalNumber INTEGER
  wfDs1E1IntervalFramerStatsMediaType INTEGER
  wfDs1E1IntervalFramerStatsBpvCounts Gauge
  wfDs1E1IntervalFramerStatsCrc4Counts Gauge
  wfDs1E1IntervalFramerStatsFebeCounts Gauge
  wfDs1E1IntervalFramerStatsOofCounts Gauge
  wfDs1E1IntervalFramerStatsFeCounts Gauge
  wfDs1E1IntervalFramerStatsLossFrameFailures Gauge
  wfDs1E1IntervalFramerStatsLossSignalFailures Gauge
  wfDs1E1IntervalFramerStatsAlarmIndicationFailures Gauge
  wfDs1E1IntervalFramerStatsRemoteAlarmFailures Gauge

WfDs1E1ClockEntry  
SEQUENCE    
  wfDs1E1ClockDelete INTEGER
  wfDs1E1ClockPortLineNumber INTEGER
  wfDs1E1ClockPrimaryClock INTEGER
  wfDs1E1ClockSecondaryClock INTEGER
  wfDs1E1ClockCurrentClock INTEGER
  wfDs1E1ClockLoopClockOperational INTEGER
  wfDs1E1ClockExtClockOperational INTEGER

WfDs1E1LineCfgEntry  
SEQUENCE    
  wfDs1E1LineCfgDelete INTEGER
  wfDs1E1LineCfgDisable INTEGER
  wfDs1E1LineCfgState INTEGER
  wfDs1E1LineLastChange TimeTicks
  wfDs1E1LineCfgPortLineNumber INTEGER
  wfDs1E1LineCfgIndex INTEGER
  wfDs1E1LineCfgIfIndex INTEGER
  wfDs1E1LineCfgCct INTEGER
  wfDs1E1LineCfgLineNumber INTEGER
  wfDs1E1LineCfgQosServicePkg INTEGER
  wfDs1E1LineCfgTimeSlotAssign INTEGER
  wfDs1E1LineCfgActualTimeSlotAssign DisplayString
  wfDs1E1LineCfgWanProtocol INTEGER
  wfDs1E1LineCfgRateAdaption INTEGER
  wfDs1E1LineCfgIFTF INTEGER
  wfDs1E1LineCfgCRCSize INTEGER
  wfDs1E1LineCfgMtu INTEGER
  wfDs1E1LineCfgBertMode INTEGER
  wfDs1E1LineCfgBertTestPattern INTEGER
  wfDs1E1LineCfgFractionalLoopback INTEGER
  wfDs1E1LineCfgAcceptFracLoopCode INTEGER
  wfDs1E1LineCfgManagerMethod INTEGER

WfDs1E1LineStatEntry  
SEQUENCE    
  wfDs1E1LineStatPortLineNumber INTEGER
  wfDs1E1LineStatIndex INTEGER
  wfDs1E1LineStatRxOctets Counter
  wfDs1E1LineStatTxOctets Counter
  wfDs1E1LineStatRxFrames Counter
  wfDs1E1LineStatTxFrames Counter
  wfDs1E1LineStatRxErrors Counter
  wfDs1E1LineStatTxErrors Counter
  wfDs1E1LineStatRxDropPackets Counter
  wfDs1E1LineStatTxDropPackets Counter
  wfDs1E1LineStatTxUnderflows Counter
  wfDs1E1LineStatRxOverflows Counter
  wfDs1E1LineStatRxShortFrames Counter
  wfDs1E1LineStatRxCRCErrors Counter
  wfDs1E1LineStatRxNonOctetBits Counter
  wfDs1E1LineStatRxLongFrames Counter
  wfDs1E1LineStatRxAbortFrames Counter

WfDs1E1DayCurrentEntry  
SEQUENCE    
  wfDs1E1DayCurrentPortLineNumber INTEGER
  wfDs1E1DayCurrentESs Gauge
  wfDs1E1DayCurrentSESs Gauge
  wfDs1E1DayCurrentSEFSs Gauge
  wfDs1E1DayCurrentUASs Gauge
  wfDs1E1DayCurrentCSSs Gauge
  wfDs1E1DayCurrentPCVs Gauge
  wfDs1E1DayCurrentLESs Gauge
  wfDs1E1DayCurrentBESs Gauge
  wfDs1E1DayCurrentDMs Gauge
  wfDs1E1DayCurrentLCVs Gauge
  wfDs1E1DayCurrentSASs Gauge
  wfDs1E1DayCurrentAISSs Gauge
  wfDs1E1DayCurrentFCs Gauge
  wfDs1E1DayCurrentTimeElapsed INTEGER
  wfDs1E1DayCurrentValidIntervals INTEGER
  wfDs1E1DayCurrentValidFlag INTEGER

WfDs1E1DayIntervalEntry  
SEQUENCE    
  wfDs1E1DayIntervalPortLineNumber INTEGER
  wfDs1E1DayIntervalNumber INTEGER
  wfDs1E1DayIntervalESs Gauge
  wfDs1E1DayIntervalSESs Gauge
  wfDs1E1DayIntervalSEFSs Gauge
  wfDs1E1DayIntervalUASs Gauge
  wfDs1E1DayIntervalCSSs Gauge
  wfDs1E1DayIntervalPCVs Gauge
  wfDs1E1DayIntervalLESs Gauge
  wfDs1E1DayIntervalBESs Gauge
  wfDs1E1DayIntervalDMs Gauge
  wfDs1E1DayIntervalLCVs Gauge
  wfDs1E1DayIntervalSASs Gauge
  wfDs1E1DayIntervalAISSs Gauge
  wfDs1E1DayIntervalFCs Gauge
  wfDs1E1DayIntervalValidFlag INTEGER

WfDs1E1DayTotalEntry  
SEQUENCE    
  wfDs1E1DayTotalPortLineNumber INTEGER
  wfDs1E1DayTotalESs Gauge
  wfDs1E1DayTotalSESs Gauge
  wfDs1E1DayTotalSEFSs Gauge
  wfDs1E1DayTotalUASs Gauge
  wfDs1E1DayTotalCSSs Gauge
  wfDs1E1DayTotalPCVs Gauge
  wfDs1E1DayTotalLESs Gauge
  wfDs1E1DayTotalBESs Gauge
  wfDs1E1DayTotalDMs Gauge
  wfDs1E1DayTotalLCVs Gauge
  wfDs1E1DayTotalSASs Gauge
  wfDs1E1DayTotalAISSs Gauge
  wfDs1E1DayTotalFCs Gauge
  wfDs1E1DayTotalValidFlag INTEGER

WfDs1E1FarEndCurrentEntry  
SEQUENCE    
  wfDs1E1FarEndCurrentPortLineNumber INTEGER
  wfDs1E1FarEndCurrentESs Gauge
  wfDs1E1FarEndCurrentSESs Gauge
  wfDs1E1FarEndCurrentSEFSs Gauge
  wfDs1E1FarEndCurrentUASs Gauge
  wfDs1E1FarEndCurrentCSSs Gauge
  wfDs1E1FarEndCurrentPCVs Gauge
  wfDs1E1FarEndCurrentLESs Gauge
  wfDs1E1FarEndCurrentBESs Gauge
  wfDs1E1FarEndCurrentDMs Gauge
  wfDs1E1FarEndCurrentLCVs Gauge
  wfDs1E1FarEndCurrentSASs Gauge
  wfDs1E1FarEndCurrentAISSs Gauge
  wfDs1E1FarEndCurrentFCs Gauge
  wfDs1E1FarEndCurrentTimeElapsed INTEGER
  wfDs1E1FarEndCurrentValidIntervals INTEGER
  wfDs1E1FarEndCurrentValidFlag INTEGER

WfDs1E1FarEndIntervalEntry  
SEQUENCE    
  wfDs1E1FarEndIntervalPortLineNumber INTEGER
  wfDs1E1FarEndIntervalNumber INTEGER
  wfDs1E1FarEndIntervalESs Gauge
  wfDs1E1FarEndIntervalSESs Gauge
  wfDs1E1FarEndIntervalSEFSs Gauge
  wfDs1E1FarEndIntervalUASs Gauge
  wfDs1E1FarEndIntervalCSSs Gauge
  wfDs1E1FarEndIntervalPCVs Gauge
  wfDs1E1FarEndIntervalLESs Gauge
  wfDs1E1FarEndIntervalBESs Gauge
  wfDs1E1FarEndIntervalDMs Gauge
  wfDs1E1FarEndIntervalLCVs Gauge
  wfDs1E1FarEndIntervalSASs Gauge
  wfDs1E1FarEndIntervalAISSs Gauge
  wfDs1E1FarEndIntervalFCs Gauge
  wfDs1E1FarEndIntervalValidFlag INTEGER

WfDs1E1FarEndTotalEntry  
SEQUENCE    
  wfDs1E1FarEndTotalPortLineNumber INTEGER
  wfDs1E1FarEndTotalESs Gauge
  wfDs1E1FarEndTotalSESs Gauge
  wfDs1E1FarEndTotalSEFSs Gauge
  wfDs1E1FarEndTotalUASs Gauge
  wfDs1E1FarEndTotalCSSs Gauge
  wfDs1E1FarEndTotalPCVs Gauge
  wfDs1E1FarEndTotalLESs Gauge
  wfDs1E1FarEndTotalBESs Gauge
  wfDs1E1FarEndTotalDMs Gauge
  wfDs1E1FarEndTotalLCVs Gauge
  wfDs1E1FarEndTotalSASs Gauge
  wfDs1E1FarEndTotalAISSs Gauge
  wfDs1E1FarEndTotalFCs Gauge
  wfDs1E1FarEndTotalValidFlag INTEGER

WfDs1E1FarEndDayCurrentEntry  
SEQUENCE    
  wfDs1E1FarEndDayCurrentPortLineNumber INTEGER
  wfDs1E1FarEndDayCurrentESs Gauge
  wfDs1E1FarEndDayCurrentSESs Gauge
  wfDs1E1FarEndDayCurrentSEFSs Gauge
  wfDs1E1FarEndDayCurrentUASs Gauge
  wfDs1E1FarEndDayCurrentCSSs Gauge
  wfDs1E1FarEndDayCurrentPCVs Gauge
  wfDs1E1FarEndDayCurrentLESs Gauge
  wfDs1E1FarEndDayCurrentBESs Gauge
  wfDs1E1FarEndDayCurrentDMs Gauge
  wfDs1E1FarEndDayCurrentLCVs Gauge
  wfDs1E1FarEndDayCurrentSASs Gauge
  wfDs1E1FarEndDayCurrentAISSs Gauge
  wfDs1E1FarEndDayCurrentFCs Gauge
  wfDs1E1FarEndDayCurrentTimeElapsed INTEGER
  wfDs1E1FarEndDayCurrentValidIntervals INTEGER
  wfDs1E1FarEndDayCurrentValidFlag INTEGER

WfDs1E1FarEndDayIntervalEntry  
SEQUENCE    
  wfDs1E1FarEndDayIntervalPortLineNumber INTEGER
  wfDs1E1FarEndDayIntervalNumber INTEGER
  wfDs1E1FarEndDayIntervalESs Gauge
  wfDs1E1FarEndDayIntervalSESs Gauge
  wfDs1E1FarEndDayIntervalSEFSs Gauge
  wfDs1E1FarEndDayIntervalUASs Gauge
  wfDs1E1FarEndDayIntervalCSSs Gauge
  wfDs1E1FarEndDayIntervalPCVs Gauge
  wfDs1E1FarEndDayIntervalLESs Gauge
  wfDs1E1FarEndDayIntervalBESs Gauge
  wfDs1E1FarEndDayIntervalDMs Gauge
  wfDs1E1FarEndDayIntervalLCVs Gauge
  wfDs1E1FarEndDayIntervalSASs Gauge
  wfDs1E1FarEndDayIntervalAISSs Gauge
  wfDs1E1FarEndDayIntervalFCs Gauge
  wfDs1E1FarEndDayIntervalValidFlag INTEGER

WfDs1E1FarEndDayTotalEntry  
SEQUENCE    
  wfDs1E1FarEndDayTotalPortLineNumber INTEGER
  wfDs1E1FarEndDayTotalESs Gauge
  wfDs1E1FarEndDayTotalSESs Gauge
  wfDs1E1FarEndDayTotalSEFSs Gauge
  wfDs1E1FarEndDayTotalUASs Gauge
  wfDs1E1FarEndDayTotalCSSs Gauge
  wfDs1E1FarEndDayTotalPCVs Gauge
  wfDs1E1FarEndDayTotalLESs Gauge
  wfDs1E1FarEndDayTotalBESs Gauge
  wfDs1E1FarEndDayTotalDMs Gauge
  wfDs1E1FarEndDayTotalLCVs Gauge
  wfDs1E1FarEndDayTotalSASs Gauge
  wfDs1E1FarEndDayTotalAISSs Gauge
  wfDs1E1FarEndDayTotalFCs Gauge
  wfDs1E1FarEndDayTotalValidFlag INTEGER

WfDs1E1ThrAlrtEntry  
SEQUENCE    
  wfDs1E1ThrAlrtDelete INTEGER
  wfDs1E1ThrAlrtPortLineNumber INTEGER
  wfDs1E1ThrAlrtESs Gauge
  wfDs1E1ThrAlrtSESs Gauge
  wfDs1E1ThrAlrtSEFSs Gauge
  wfDs1E1ThrAlrtUASs Gauge
  wfDs1E1ThrAlrtCSSs Gauge
  wfDs1E1ThrAlrtPCVs Gauge
  wfDs1E1ThrAlrtLESs Gauge
  wfDs1E1ThrAlrtBESs Gauge
  wfDs1E1ThrAlrtDMs Gauge
  wfDs1E1ThrAlrtLCVs Gauge
  wfDs1E1ThrAlrtSASs Gauge
  wfDs1E1ThrAlrtAISSs Gauge
  wfDs1E1ThrAlrtFCs Gauge

WfDs1E1DayThrAlrtEntry  
SEQUENCE    
  wfDs1E1DayThrAlrtDelete INTEGER
  wfDs1E1DayThrAlrtPortLineNumber INTEGER
  wfDs1E1DayThrAlrtESs Gauge
  wfDs1E1DayThrAlrtSESs Gauge
  wfDs1E1DayThrAlrtSEFSs Gauge
  wfDs1E1DayThrAlrtUASs Gauge
  wfDs1E1DayThrAlrtCSSs Gauge
  wfDs1E1DayThrAlrtPCVs Gauge
  wfDs1E1DayThrAlrtLESs Gauge
  wfDs1E1DayThrAlrtBESs Gauge
  wfDs1E1DayThrAlrtDMs Gauge
  wfDs1E1DayThrAlrtLCVs Gauge
  wfDs1E1DayThrAlrtSASs Gauge
  wfDs1E1DayThrAlrtAISSs Gauge
  wfDs1E1DayThrAlrtFCs Gauge

WfDs1E1FarEndThrAlrtEntry  
SEQUENCE    
  wfDs1E1FarEndThrAlrtDelete INTEGER
  wfDs1E1FarEndThrAlrtPortLineNumber INTEGER
  wfDs1E1FarEndThrAlrtESs Gauge
  wfDs1E1FarEndThrAlrtSESs Gauge
  wfDs1E1FarEndThrAlrtSEFSs Gauge
  wfDs1E1FarEndThrAlrtUASs Gauge
  wfDs1E1FarEndThrAlrtCSSs Gauge
  wfDs1E1FarEndThrAlrtPCVs Gauge
  wfDs1E1FarEndThrAlrtLESs Gauge
  wfDs1E1FarEndThrAlrtBESs Gauge
  wfDs1E1FarEndThrAlrtDMs Gauge
  wfDs1E1FarEndThrAlrtLCVs Gauge
  wfDs1E1FarEndThrAlrtSASs Gauge
  wfDs1E1FarEndThrAlrtAISSs Gauge
  wfDs1E1FarEndThrAlrtFCs Gauge

WfDs1E1FarEndDayThrAlrtEntry  
SEQUENCE    
  wfDs1E1FarEndDayThrAlrtDelete INTEGER
  wfDs1E1FarEndDayThrAlrtPortLineNumber INTEGER
  wfDs1E1FarEndDayThrAlrtESs Gauge
  wfDs1E1FarEndDayThrAlrtSESs Gauge
  wfDs1E1FarEndDayThrAlrtSEFSs Gauge
  wfDs1E1FarEndDayThrAlrtUASs Gauge
  wfDs1E1FarEndDayThrAlrtCSSs Gauge
  wfDs1E1FarEndDayThrAlrtPCVs Gauge
  wfDs1E1FarEndDayThrAlrtLESs Gauge
  wfDs1E1FarEndDayThrAlrtBESs Gauge
  wfDs1E1FarEndDayThrAlrtDMs Gauge
  wfDs1E1FarEndDayThrAlrtLCVs Gauge
  wfDs1E1FarEndDayThrAlrtSASs Gauge
  wfDs1E1FarEndDayThrAlrtAISSs Gauge
  wfDs1E1FarEndDayThrAlrtFCs Gauge

WfDs1E1LineQueStatEntry  
SEQUENCE    
  wfDs1E1LineQueStatPortLineNumber INTEGER
  wfDs1E1LineQueStatLineIndex INTEGER
  wfDs1E1LineQueStatQueueIndex INTEGER
  wfDs1E1LineQueStatTxOctets Counter
  wfDs1E1LineQueStatTxPackets Counter
  wfDs1E1LineQueStatTxDrops Counter

Defined Values

wfDs1E1ModuleTable 1.3.6.1.4.1.18.3.4.9.1
This file describes the MIBS for managing the Multichannel T1 and E1 link modules. DS1E1 MOD record - Contains DS1E1 module Configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1ModuleEntry

wfDs1E1ModuleEntry 1.3.6.1.4.1.18.3.4.9.1.1
An entry in the DS1E1 Base table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1ModuleEntry  

wfDs1E1ModuleDelete 1.3.6.1.4.1.18.3.4.9.1.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1ModuleSlot 1.3.6.1.4.1.18.3.4.9.1.1.2
Instance ID slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ModuleModule 1.3.6.1.4.1.18.3.4.9.1.1.3
Instance ID slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ModulePrimaryClock 1.3.6.1.4.1.18.3.4.9.1.1.4
Specifies the primary source for transmit timing. Both ports use the same transmit timing source. The options for timing source are internal timing source, loop timing from either port and an external timing source.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER external(1), loop1(2), loop2(3), internal(4), loop3(5), loop4(6)  

wfDs1E1ModuleSecondaryClock 1.3.6.1.4.1.18.3.4.9.1.1.5
Specifies the secondary source for transmit timing. During normal operation transmit timing is derived from the primary timing source. If the primary timing source fails, the software switches to secondary timing source.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER external(1), loop1(2), loop2(3), internal(4), loop3(5), loop4(6)  

wfDs1E1ModuleCurrentClock 1.3.6.1.4.1.18.3.4.9.1.1.6
Indicates the clock source currently in use
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER external(1), loop1(2), loop2(3), internal(4), loop3(5), loop4(6)  

wfDs1E1ModuleExtClockOperational 1.3.6.1.4.1.18.3.4.9.1.1.7
Indicates whether the External clock is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ModuleLoop1ClockOperational 1.3.6.1.4.1.18.3.4.9.1.1.8
Indicates whether the timing source from port 1 is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ModuleLoop2ClockOperational 1.3.6.1.4.1.18.3.4.9.1.1.9
Indicates whether the timing source from port 2 is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ModuleLoop3ClockOperational 1.3.6.1.4.1.18.3.4.9.1.1.10
Indicates whether the timing source from port 3 is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ModuleLoop4ClockOperational 1.3.6.1.4.1.18.3.4.9.1.1.11
Indicates whether the timing source from port 4 is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ModuleCfgTxBufferUseCredits 1.3.6.1.4.1.18.3.4.9.1.1.12
Configured Transmit Buffer Credits. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. All values are accepted. Care should be taken not to set this to a value which is much greater than the default. The default can be read out of the wfDs1E1ModuleTxBufferUseCredits attribute when the router is running with this attribute set to zero. Sets to this attribute may take up to one minute to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..512  

wfDs1E1ModuleCfgRxBufferUseCredits 1.3.6.1.4.1.18.3.4.9.1.1.13
Configured Receive Buffer Credits. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero cuases router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. Sets to this attribute may take up to one minute to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..512  

wfDs1E1ModuleTxBufferUseCredits 1.3.6.1.4.1.18.3.4.9.1.1.14
Current Transmit Buffers available for use by module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ModuleRxBufferUseCredits 1.3.6.1.4.1.18.3.4.9.1.1.15
Current Receive Buffers available for use by module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortMapTable 1.3.6.1.4.1.18.3.4.9.2
DS1E1 port map record - Used by the driver to identify the LineNumber for the Port. The only table indexed by slot.connector. Its purpose is to map slot.connector to a PortLineNumber.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1PortMapEntry

wfDs1E1PortMapEntry 1.3.6.1.4.1.18.3.4.9.2.1
An entry in the DS1E1 port table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1PortMapEntry  

wfDs1E1PortMapDelete 1.3.6.1.4.1.18.3.4.9.2.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1PortMapSlot 1.3.6.1.4.1.18.3.4.9.2.1.2
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortMapConnector 1.3.6.1.4.1.18.3.4.9.2.1.3
Instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortMapLineNumber 1.3.6.1.4.1.18.3.4.9.2.1.4
LineNumber off of which all other MIB instances are indexed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortMapDslId 1.3.6.1.4.1.18.3.4.9.2.1.5
When this T1/E1 interface is configured for Primary Rate ISDN (PRI) this attribute provides the ID of this Digital Subscriber Loop (DSL) interface. Each T1 or E1 PRI interface on a particular slot is assigned a unique DSL ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortTable 1.3.6.1.4.1.18.3.4.9.3
DS1E1 port record - Contains MUNICH32 Configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1PortEntry

wfDs1E1PortEntry 1.3.6.1.4.1.18.3.4.9.3.1
An entry in the DS1E1 port table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1PortEntry  

wfDs1E1PortDelete 1.3.6.1.4.1.18.3.4.9.3.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1PortDisable 1.3.6.1.4.1.18.3.4.9.3.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1PortState 1.3.6.1.4.1.18.3.4.9.3.1.3
Line Driver state variable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), yelalarm(2), aisalarm(3), redalarm(4), loopback(10), bert(11), init(15), notpresent(20)  

wfDs1E1PortLineNumber 1.3.6.1.4.1.18.3.4.9.3.1.4
LineNumber for this port. This value is assigned at configuration time and uniquely identifies this interface. This LineNumber not equal to any of the LineNumbers assigned to the LogicalLines configured through this Port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortMtu 1.3.6.1.4.1.18.3.4.9.3.1.5
MTU parameter. Obsoleted, it is no longer referenced.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..4608  

wfDs1E1PortSignalLevel 1.3.6.1.4.1.18.3.4.9.3.1.6
Specifies T1 transmit power level, in terms of DB. They translate into cable length as follows: 0.0dB -> 0-133 ft 0.5dB -> 133-266 ft 0.8dB -> 266-399 ft 1.1dB -> 399-533 ft 1.5dB -> 533-655 ft
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ds1-minus-15(1), ds1-minus-7point5(2), zero-point0(3), dsx1-plus-point5(4), dsx1-plus-point8(5), dsx1-plus-1point1(6), dsx1-plus-1point5(7)  

wfDs1E1PortSetupAlarmThreshold 1.3.6.1.4.1.18.3.4.9.3.1.7
Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the time specified by this parameter a performance failure is registered and a message is logged.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..10  

wfDs1E1PortClearAlarmThreshold 1.3.6.1.4.1.18.3.4.9.3.1.8
Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for greater than the time specified by this parameter then the failure cleared condition is registered and a message is logged.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..10  

wfDs1E1PortFdlTargetHdlcAddress 1.3.6.1.4.1.18.3.4.9.3.1.9
Selects between the two FDL target address modes. This determines whether the near-end FDL will respond to HDLC address AZ or BY in the FDL messages received from the far-end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER az(1), by(2)  

wfDs1E1PortAcceptLoopbackRequest 1.3.6.1.4.1.18.3.4.9.3.1.10
The DS1E1 link module is capable of detecting loop up and loop down codes received from the far end. This parameter enables and disables loop up/down code detection circuitry. If enabled, this interface will accept and comply with a request to go into loopback mode from a far end device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1PortLoopbackState 1.3.6.1.4.1.18.3.4.9.3.1.11
Indicates the current loopback state of this interface. The interface can be in one the following states: Payload Loopback Line Loopback no loopback Payload or Line loopback modes can be initiated by either of two methods: Manager requested Loopback (MGRREQPAYLOADLOOP or MGRREQLINELOOP) is initiated by the Manager of this device. Network requested Loopback (NETREQPAYLOADLOOP or NETREQLINELOOP) is initiated by this interface receiving an in-band request on the network from the far end device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noloop(1), mgrreqpayloadloop(2), mgrreqlineloop(3), netreqpayloadloop(4), netreqlineloop(5), otherloop(6)  

wfDs1E1PortBertMode 1.3.6.1.4.1.18.3.4.9.3.1.12
An option to generate and analyze specific test patterns is provided in BERT mode of operation. Only one port can be in BERT mode at a time. This attribute selects normal or BERT mode of operation
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1PortBertTestPattern 1.3.6.1.4.1.18.3.4.9.3.1.13
When a port is in BERT mode, it is capable of generating a set of known patterns. This paramater selects between those patterns
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zeros(1), ones(2), qrss(3), two15(4), two15-inv(5), two20(6), two23(7), two23-inv(8)  

wfDs1E1PortBertSendAlarm 1.3.6.1.4.1.18.3.4.9.3.1.14
Specifies a Alarm Indication Signal (AIS) (Blue Alarm) or yellow alarm to be transmitted while in BERT mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ais-alarm(1), yellow-alarm(2), disabled(3)  

wfDs1E1PortInternationalBit 1.3.6.1.4.1.18.3.4.9.3.1.15
Specifies if the International bit should be set in the E1 frame
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1PortLineApplication 1.3.6.1.4.1.18.3.4.9.3.1.16
Specifies the application that the LogicalLines of this Port will provide. NONPRI indicates that all of the LogicalLines will have a permanent Cct number and will not be used to dial to varying destinations. PRI indicates that some or all of the ds0s of this port will be used for switched Ccts using ISDN. MIXED indicates that some of the ds0s are being used for switched Ccts using ISDN and some are being used for non PRI permanent connections for other applications such as leased lines or Frame Relay.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonpri(1), pri(2), mixed(3), frswpri(4)  

wfDs1E1PortLoggingEnableMask 1.3.6.1.4.1.18.3.4.9.3.1.17
Specifies which catagories of extended event log messages are enabled for logging. Current bit definitions are: bit 31 bit 0 +--------------------------------+ | | +--------------------------------+ bit0 ISDN PRI debug messages bit1-31 reserved
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1PortSendPrmCrAddressBit 1.3.6.1.4.1.18.3.4.9.3.1.18
Specifies the Performance message as originating from either a Carrier or Customer Installation (CI). As the performance message is sent out the FDL, the PRM Opening Address C/R bit is either set (Carrier) or cleared (CI). This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER prm-ci(1), prm-carrier(2)  

wfDs1E1PortAcceptPrmCrAddressBit 1.3.6.1.4.1.18.3.4.9.3.1.19
Accepts only Performance messages originating from either a Carrier or Customer Installation (CI), as determined below. The PRM Opening Address C/R bit is read upon receiving a performance message. If the Performance message does not originate from the expected source, it is discarded. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER prm-ci(1), prm-carrier(2)  

wfDs1E1PortLineImpedanceOption 1.3.6.1.4.1.18.3.4.9.3.1.20
Supports user selectible Line Impedance option for ASN MCE1 Net Modules.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rj45-120-ohms(1), bnc-75-ohms(2)  

wfDs1E1PortFdlLoopInterframeFill 1.3.6.1.4.1.18.3.4.9.3.1.21
Enables the Loop Retention Interframe Time Fill for the FDL after sending Loop Up Code. Also enables the detection of the Loop Retention Code when placed into Line or Payload loopback by the remote end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mark(1), loop-retention(2)  

wfDs1E1PortRelayCtrl 1.3.6.1.4.1.18.3.4.9.3.1.22
The Relay on the QMCT1 will always be placed into loopback for the following conditions: 1. Power Up 2. Reboot 3. Hardware Reset Button 4. System CRASH However, when altering QMCT1 Port or Module MIBs' attributes with a restart characteristic, the state of the Relay will be controlled by this MIB attribute. When set to loop (1), the Relay will go into loopback as the Port/Module is re-initialized. The Relay will come out of loopback as the Port/Module re-initialization is complete. When set to noLoop (2), the Relay will remain in its present state as the Port/Module is re-initialized.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loop(1), no-loop(2)  

wfDs1E1PortRelayStatus 1.3.6.1.4.1.18.3.4.9.3.1.23
This attribute indicates the current state of the Relay on the QMCT1. When set to loop (1), the Relay is currently looping data from the Rx path onto the Tx path. When set to noLoop (2), the Rx path and Tx path are connected to the Framer. Note that the Framer may be placed into loopback without affecting this attribute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER loop(1), noLoop(2)  

wfDs1E1PortPrimaryClockSource 1.3.6.1.4.1.18.3.4.9.3.1.24
Selects the Primary source of the Tx Clock for the DS1/E1 interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop(3)  

wfDs1E1PortSecondaryClockSource 1.3.6.1.4.1.18.3.4.9.3.1.25
Selects the Secondary source of the Tx Clock for the DS1/E1 interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop(3)  

wfDs1E1PortCurrentClock 1.3.6.1.4.1.18.3.4.9.3.1.26
Indicates the clock source currently in use by the DS1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop(3)  

wfDs1E1PortExtClockOperational 1.3.6.1.4.1.18.3.4.9.3.1.27
Indicates whether the External clock is operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1PortTransmitWaveform 1.3.6.1.4.1.18.3.4.9.3.1.28
Specifies T1 transmit waveform settings. Legal values are: long haul (LBO 0.0dB) long haul (LBO 7.5dB) long haul (LBO 15.0dB) long haul (LBO 22.5dB) short haul (0-110 ft) short haul (110-220 ft) short haul (220-330 ft) short haul (330-440 ft) short haul (440-550 ft) short haul (550-660 ft) Note that this attribute is not supported by all T1 interfaces. For those interfaces that DO NOT support this attribute, the wfDs1E1PortSignalLevel attribute is used instead.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER long-haul-0point0(1), long-haul-7point5(2), long-haul-15point0(3), long-haul-22point5(4), short-haul-0to110(5), short-haul-110to220(6), short-haul-220to330(7), short-haul-330to440(8), short-haul-440to550(9), short-haul-550to660(10)  

wfDs1E1ConfigTable 1.3.6.1.4.1.18.3.4.9.4
DS1E1 Configuration Table. This is a copy of the dsx1ConfigTable found in RFC1406. The table is indexed with PortLineNumber instead of ifIndex, however.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1ConfigEntry

wfDs1E1ConfigEntry 1.3.6.1.4.1.18.3.4.9.4.1
An entry in the DS1E1 config table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1ConfigEntry  

wfDs1E1ConfigDelete 1.3.6.1.4.1.18.3.4.9.4.1.1
Create/Delete attribute
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1ConfigPortLineNumber 1.3.6.1.4.1.18.3.4.9.4.1.2
The index ID for this record. It is the line number assigned to a port in the wfDs1E1PortMapEntry for a port.connector pair. Its channel field should be 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ConfigIfIndex 1.3.6.1.4.1.18.3.4.9.4.1.3
Currently this is the sames as wfDs1E1LinePortIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ConfigTimeElapsed 1.3.6.1.4.1.18.3.4.9.4.1.4
The number of seconds that have elapsed since the beginning of the current error-measurement period. Only relevant when the wfDs1E1ConfigLineType is ESF and the wfDs1E1ConfigFdl is AT&T 54016.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ConfigValidIntervals 1.3.6.1.4.1.18.3.4.9.4.1.5
The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online. Only relevant when the wfDs1E1ConfigLineType is ESF and the wfDs1E1ConfigFdl is AT&T 54016.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ConfigLineType 1.3.6.1.4.1.18.3.4.9.4.1.6
This attribute is used to configure the line framing type to match the carrier's framing. SF and ESF are T1 framing types and the main differences between the two are the number of frames in a superframe and the use of the f-bit. The E1, E1CRC, E1MF, and E1CRCMF are used for E1 lines.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unframedt1(1), esf(2), sf(3), e1(4), e1crc(5), e1mf(6), e1crcmf(7), unframede1(8)  

wfDs1E1ConfigLineCoding 1.3.6.1.4.1.18.3.4.9.4.1.7
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. It should be set to match the carrier. AMI (alternate mark inversion) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density requirements, such as inverting HDLC data. This could be used for T1 or E1 lines. B8ZS refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. This can be used on T1 lines while HDB3 provides similar functionality for E1 links.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER jbzs(1), b8zs(2), hdb3(3), zbtsi(4), ami(5)  

wfDs1E1ConfigSendCode 1.3.6.1.4.1.18.3.4.9.4.1.8
This variable is currently read-only and it indicates what type of code is being sent across the DS1 interface by the device. The values mean: SENDNOCODE - sending looped or normal data SENDLINECODE - sending a request for a line loopback SENDPAYLOADCODE - sending a request for a payload loopback SENDRESETCODE - sending a loopback termination request SENDQRS - sending a Quasi-Random Signal (QRS) test pattern SEND511PATTERN - sending a 511 bit fixed test pattern SEND3IN24PATTERN - sending a fixed test pattern of 3 bits set in 24 SENDOTHERTESTPATTERN - sending a test pattern other than those described by this object
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sendnocode(1), sendlinecode(2), sendpayloadcode(3), sendresetcode(4), sendqrs(5), send511pattern(6), send3in24pattern(7), sendothertestpattern(8)  

wfDs1E1ConfigCircuitIdentifier 1.3.6.1.4.1.18.3.4.9.4.1.9
This attribute is not used and appears here as a place holder only. If it was implemented then it would contain the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs1E1ConfigLoopbackConfig 1.3.6.1.4.1.18.3.4.9.4.1.10
This variable represents the loopback configuration of the DS1 interface. The value NOLOOP indicates the port is not in loopback. The value PAYLOADLOOP indicates the port is in payload loopback which means that data is looped back after it goes through the framer. The value LINELOOP indicates the port is in line loopback which means that data is looped back before the framer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noloop(1), payloadloop(2), lineloop(3)  

wfDs1E1ConfigLineStatus 1.3.6.1.4.1.18.3.4.9.4.1.11
This variable is a bit-map which indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarm' information. The bit definition as as follows with bit #0 being the LSB. bit 0 NOALARM - No alarm present, set only when none of the other bits are. 1 RCVFARENDLOF - Far end LOF (a.k.a., Yellow Alarm) 2 XMTFARENDLOF - Near end sending LOF Indication 3 RCVAIS - Far end sending AIS 4 XMTAIS - Near end sending AIS 5 LOSSOFFRAME - Near end LOF (a.k.a., Red Alarm) 6 LOSSOFSIGNAL - Near end Loss Of Signal 7 LOOPBACKSTATE - Near end is looped 8 T16AIS - E1 only, TS16 AIS 9 RCVFARENDLOMF - E1 only, Far End Sending TS16 LOMF 10 XMTFARENDLOMF - E1 only, Near End Sending TS16 LOMF 11 RCVTESTCODE - Near End detects a test code 12 OTHERFAILURE - any line status not defined here'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noalarm(1), rcvfarendlof(2), xmtfarendlof(4), rcvais(8), xmtais(16), lossofframe(32), lossofsignal(64), loopbackstate(128), t16ais(256), rcvfarendlomf(512), xmtfarendlomf(1024), rcvtestcode(2048), otherfailure(4096)  

wfDs1E1ConfigSignalMode 1.3.6.1.4.1.18.3.4.9.4.1.12
This attribute is not implemented and exists here only as a place holder.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), robbedbit(2), bitoriented(3), messageoriented(4)  

wfDs1E1ConfigTransmitClockSource 1.3.6.1.4.1.18.3.4.9.4.1.13
The source of Tranmit Clock. LOOPTIMING indicates that the recovered receive clock is used as the transmit clock. LOCALTIMING indicates that a local clock source is used. Either the internal clock or the external clock through the extra connector on the board. THROUGHTIMING indicates that recovered receive clock from another interface is used as the transmit clock.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER looptiming(1), localtiming(2), throughtiming(3)  

wfDs1E1ConfigFdl 1.3.6.1.4.1.18.3.4.9.4.1.14
This attribute is used to configure the type facilities data link (FDL). The ANSI403 configures the port to use the FDL exchange described in the ANSI T1 403 specification. ATT54016 is used to configure the port for the for the FDL exchange listed in the AT&T 54016 document. NONE is used when no FDL is desired. The FDL can only be used when the line type is ESF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ansi403(2), att54016(4), none(8)  

wfDs1E1ActionTable 1.3.6.1.4.1.18.3.4.9.5
DS1E1 configuration Action record - Contains MUNICH32 and Framer write only Configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1ActionEntry

wfDs1E1ActionEntry 1.3.6.1.4.1.18.3.4.9.5.1
An entry in the DS1E1 Config table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1ActionEntry  

wfDs1E1ActionPortLineNumber 1.3.6.1.4.1.18.3.4.9.5.1.1
Instance ID LineNumber, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ActionBertReset 1.3.6.1.4.1.18.3.4.9.5.1.2
Reset counters on BERT device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), noaction(21)  

wfDs1E1ActionBertErrorInsert 1.3.6.1.4.1.18.3.4.9.5.1.3
Indicates that an error be injected into the transmitted data stream while in BERT mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER oneerror(1), errorperthousand(2), errorpermillion(3), disable(4), noaction(21)  

wfDs1E1ActionSendLoopCode 1.3.6.1.4.1.18.3.4.9.5.1.4
Selects a Loop Up/Down code to be sent to the remote end
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loopup(1), loopdown(2), noaction(21)  

wfDs1E1ActionSendFdlLoopbackCode 1.3.6.1.4.1.18.3.4.9.5.1.5
Selects an FDL code to be sent to the remote end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lineloopci(1), lineloopia(2), lineloopib(3), deactivatell(4), payloadloop(5), deactivatepl(6), deactivateall(7), noaction(21)  

wfDs1E1ActionSendLoopUpFractionalCode 1.3.6.1.4.1.18.3.4.9.5.1.6
Selects Fractional Loop Up code to be sent to the remote end. Value passed through this attribute is the Logical Line number (1 through 24). This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noaction(33)  

wfDs1E1ActionSendLoopDownFractionalCode 1.3.6.1.4.1.18.3.4.9.5.1.7
Selects Fractional Loop Down code to be sent to the remote end. Value passed through this attribute is the Logical Line number (1 through 24). This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noaction(33)  

wfDs1E1ActionClearFractionalLoopState 1.3.6.1.4.1.18.3.4.9.5.1.8
Removes any Logical Line left in hardware Fractional T1 loopback state. The Logical Line number is passed as an argument. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noaction(33)  

wfDs1E1ActionClearFdlStats 1.3.6.1.4.1.18.3.4.9.5.1.9
Clears this port's FDL Statistics. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearCurrentStats 1.3.6.1.4.1.18.3.4.9.5.1.10
Clears this port's Current 15 minute Statistics.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearFarEndCurrentStats 1.3.6.1.4.1.18.3.4.9.5.1.11
Clears this port's Far End, Current 15 minute Statistics.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearDayCurrentStats 1.3.6.1.4.1.18.3.4.9.5.1.12
Clears this port's Current Day Statistics.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearFarEndDayCurrentStats 1.3.6.1.4.1.18.3.4.9.5.1.13
Clears this port's Far End, Current Day Statistics.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearIntervalStats 1.3.6.1.4.1.18.3.4.9.5.1.14
Clears All Interval Statistics (15 minute and day) of this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfDs1E1ActionClearFarEndIntervalStats 1.3.6.1.4.1.18.3.4.9.5.1.15
Clears All Far End Interval Statistics (15 minute and day) of this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), noaction(2)  

wfLogicalLineTable 1.3.6.1.4.1.18.3.4.9.6
LogicalLine record - Contains configuration parameters and statistics for MUNICH32 which are LogicalLine specific.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfLogicalLineEntry

wfLogicalLineEntry 1.3.6.1.4.1.18.3.4.9.6.1
An entry in the LOGICAL_LINE table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfLogicalLineEntry  

wfLogicalLineDelete 1.3.6.1.4.1.18.3.4.9.6.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfLogicalLineDisable 1.3.6.1.4.1.18.3.4.9.6.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineState 1.3.6.1.4.1.18.3.4.9.6.1.3
Line Driver state variable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), lmiwait(4), loopback(5), linedieing(6), linedead(7), remoteloop(8), remotedeaf(9), bert(10), hwfrac(11), priWait(12), lineloopbofltest(19), notpresent(20)  

wfLogicalLinePortLineNumber 1.3.6.1.4.1.18.3.4.9.6.1.4
Instance ID PortLineNumber, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineIndex 1.3.6.1.4.1.18.3.4.9.6.1.5
Index for this line instance, filled in by driver. The index corresponds to the position of the circuit, from 1 to 31, on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineCct 1.3.6.1.4.1.18.3.4.9.6.1.6
Circuit number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfLogicalLineLineNumber 1.3.6.1.4.1.18.3.4.9.6.1.7
LineNumber for this logical line instance. This is the same line number contained in the PORT_TABLE with the channel field nonzero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfLogicalLineBofl 1.3.6.1.4.1.18.3.4.9.6.1.8
Selects Breath of Life (BOFL) parameter. If selected, a BOFL packet is sent out on the wire as often as specifies by the wfLogicalLineBoflTmo parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineBoflTmo 1.3.6.1.4.1.18.3.4.9.6.1.9
Indicates the time-period between BOFL packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

wfLogicalLineFractionalLoopback 1.3.6.1.4.1.18.3.4.9.6.1.10
Any Logical Line on this T1/E1 port is capable of being put into loopback, i.e. data coming into that circuit from the wire is mirrorred back onto the wire. This parameter enables or disables this loopback feature on any circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineTimeSlotAssignment 1.3.6.1.4.1.18.3.4.9.6.1.11
Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 31 used by the channel
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfLogicalLineMtu 1.3.6.1.4.1.18.3.4.9.6.1.12
Contains the largest frame size that can be received by the logical line. Anything larger than the MTU will be discarded. In all cases except when the wfLogicalLineWanProtocol is LAPB, this value will be the same as wfLogicalLineCfgMtu. In the LAPB case it will be twice wfLogicalLineCfgMtu with a maximum of 4608.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineMadr 1.3.6.1.4.1.18.3.4.9.6.1.13
Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfLogicalLineWanProtocol 1.3.6.1.4.1.18.3.4.9.6.1.14
WAN protocol selection is provided via this parameter. The supported protocols can be selected per circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), passthru(2), ppp(3), smds(4), framerelay(5), x25(6), switch(7), sw(8), atm(9), lapb(10), sdlc(11)  

wfLogicalLineHdlcService 1.3.6.1.4.1.18.3.4.9.6.1.15
HDLC Service type for this line. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER transparent(1), llc1(2)  

wfLogicalLineLocalHdlcAddress 1.3.6.1.4.1.18.3.4.9.6.1.16
This attribute is only used if the Wan protocol is Wellfleet Standard Proprietary Point to Point. This attribute is unused for other Wan protocols. The local HDLC address can take on values between 1 and 7. The default is 7. 1 is refered to as DCE. 3 is refered to DTE. All others are refered to as EXPLICIT. EXPLICIT indicates that the user has explicitely selected the address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dce(1), dte(3), seven(7)  

wfLogicalLineRemoteHdlcAddress 1.3.6.1.4.1.18.3.4.9.6.1.17
This attribute is only used if the Wan protocol is Wellfleet Standard Proprietary Point to Point. This attribute is unused for other Wan protocols. The remote HDLC address can take on values between 1 and 7. The default is 7. 1 is refered to as DCE. 3 is refered to DTE. All others are refered to as EXPLICIT. EXPLICIT indicates that the user has explicitely selected the address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dce(1), dte(3), seven(7)  

wfLogicalLineRateAdaption 1.3.6.1.4.1.18.3.4.9.6.1.18
Determines the number of bits and their bit positions within the time-slot. 64k selection uses all 8 bits in the time-slot. The two 56k selections use 7 of the 8 bits in the time-slot. 56k_MSB does not use the most significant bit and 56k_LSB does not use the least significant bit in the time-slot. If the logical line is configured for DS0-A operation, rate adaptions of 9.6 Kbps and 19.2 Kbps may be configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adaption-64k(1), adaption-56kmsb(2), adaption-56klsb(3), adaption-9dot6k(4), adaption-19dot2k(5)  

wfLogicalLineIFTF 1.3.6.1.4.1.18.3.4.9.6.1.19
Determines the Interframe time fill character to be transmitted by the MUNICH. In case of IFTF_FLAGS, 0x7E is sent and in case of IFTF_IDLES 0xff is sent as the interframe timefill characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER flags(1), idles(2)  

wfLogicalLineCRCSize 1.3.6.1.4.1.18.3.4.9.6.1.20
Determines the CRC Size. When CRC32 is selected a 32 bit CRC is appended to the frame being transmitted and a 32 bit CRC check is performed on the received frame. When CRC16 is selected, a 16 bit CRC is appended to the transmitted frame and a 16 bit CRC is performed. on the received frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crc-32(1), crc-16(2)  

wfLogicalLineRxOctets 1.3.6.1.4.1.18.3.4.9.6.1.21
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxFrames 1.3.6.1.4.1.18.3.4.9.6.1.22
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTxOctets 1.3.6.1.4.1.18.3.4.9.6.1.23
Number of octets transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTxFrames 1.3.6.1.4.1.18.3.4.9.6.1.24
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxErrors 1.3.6.1.4.1.18.3.4.9.6.1.25
Number of receive errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTxErrors 1.3.6.1.4.1.18.3.4.9.6.1.26
Number of transmission errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineLackRxResources 1.3.6.1.4.1.18.3.4.9.6.1.27
Number of Rx frames dropped due to lack of buffer resources
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineLackTxResources 1.3.6.1.4.1.18.3.4.9.6.1.28
Number of Tx frames dropped due to lack of system resources
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTxUnderflows 1.3.6.1.4.1.18.3.4.9.6.1.29
Number of Tx frames dropped due to Transmit underflow
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxOverflows 1.3.6.1.4.1.18.3.4.9.6.1.30
Number of Rx frames dropped due to Receive overflow
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxNullFrames 1.3.6.1.4.1.18.3.4.9.6.1.31
Number of short frames received (with no data bytes)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxShortFrames 1.3.6.1.4.1.18.3.4.9.6.1.32
Number of short frames received whose length is either 1 or 2 data bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxLossSyncs 1.3.6.1.4.1.18.3.4.9.6.1.33
Loss of synchronization on receiver
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxCRCErrors 1.3.6.1.4.1.18.3.4.9.6.1.34
CRC error received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxNonOctetBits 1.3.6.1.4.1.18.3.4.9.6.1.35
Non-Octet bits received in frame
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxLongFrames 1.3.6.1.4.1.18.3.4.9.6.1.36
Frame longer than MFL received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxAbortFrames 1.3.6.1.4.1.18.3.4.9.6.1.37
Aborted frame received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxDescOverflows 1.3.6.1.4.1.18.3.4.9.6.1.38
Receive overflow on chip buffer
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxReplenMisses 1.3.6.1.4.1.18.3.4.9.6.1.39
Count of number of packet buffer misses while attempting to replenish driver receive ring
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxIFCs 1.3.6.1.4.1.18.3.4.9.6.1.40
Number of times the device detects a change of interframe time-fill between incomming frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxDropPackets 1.3.6.1.4.1.18.3.4.9.6.1.41
Number of packets dropped after reception
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineCfgTxQueueLength 1.3.6.1.4.1.18.3.4.9.6.1.42
Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. All values are accepted. Care should be taken not to set this to a value which is much greater than the default. The default can be read out of the wfLoigcalLineTxQueueLength attribute when the router is running with this attribute set to zero. Sets to this attribute may take up to one minute to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..512  

wfLogicalLineCfgRxQueueLength 1.3.6.1.4.1.18.3.4.9.6.1.43
Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero cuases router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. Sets to this attribute may take up to one minute to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..512  

wfLogicalLineTxQueueLength 1.3.6.1.4.1.18.3.4.9.6.1.44
Current hardware transmit queue length
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineRxQueueLength 1.3.6.1.4.1.18.3.4.9.6.1.45
Current Receive queue length
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineTxQueueEmpties 1.3.6.1.4.1.18.3.4.9.6.1.46
The number of times the transmit ring is found empty when transmitting packets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxIntProcs 1.3.6.1.4.1.18.3.4.9.6.1.47
DEBUG paramete - Receive Interrupt processing count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTxIntProcs 1.3.6.1.4.1.18.3.4.9.6.1.48
DEBUG parameter - Tx interrupt processing count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRxPktCorruptions 1.3.6.1.4.1.18.3.4.9.6.1.49
DEBUG parameter - Corruption check on receive
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineTurboBofl 1.3.6.1.4.1.18.3.4.9.6.1.50
DEBUG parameter - Turbo bofl enabled or disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineBoflNum 1.3.6.1.4.1.18.3.4.9.6.1.51
DEBUG parameter - Number of breath of life packets per breath of life
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..127  

wfLogicalLineBoflLen 1.3.6.1.4.1.18.3.4.9.6.1.52
DEBUG parameter - breath of life packet length
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 22..4450  

wfLogicalLineOutQLen 1.3.6.1.4.1.18.3.4.9.6.1.53
The instantaneous current length of the output packet queue (in packets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfLogicalLineLastChange 1.3.6.1.4.1.18.3.4.9.6.1.54
The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second) since the network management portion of the system was last re-initialized. Usually the time since boot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfLogicalLineCfgMtu 1.3.6.1.4.1.18.3.4.9.6.1.55
Specifies the largest frame size that can be received by the logical line. Anything larger than the MTU will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..4608  

wfLogicalLineRemoteLpbkDetection 1.3.6.1.4.1.18.3.4.9.6.1.56
This attribute enables Remote Loopback Detection. When enabled along with wfLogicalLineBofl, the device driver will detect when it is receiving its own BOFL packets and will bring the interface down assuming that somewhere down stream the link has been put into loopback.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineLastState 1.3.6.1.4.1.18.3.4.9.6.1.57
The state which the Logical Line driver was in prior to the most recent re-initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), lmiwait(4), loopback(5), linedieing(6), linedead(7), remoteloop(8), remotedeaf(9), bert(10), hwfrac(11), priWait(12), notpresent(20)  

wfLogicalLineRxIdles 1.3.6.1.4.1.18.3.4.9.6.1.58
Number of received frames followed by ShortFrame errors reported by the hardware. ShortFrame errors imediately after received frames actually indicates an Idle (all 1s) interframe time fill. One ShortFrame is allowed per received frame without incrementing wfLogicalLineRxErrors or wfLogicalLineRxShortFrames. Additional ShortFrames will not increment wfLogicalLineRxIdles but will increment both wfLogicalLineRxErrors and wfLogicalLineRxShortFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLogicalLineRole 1.3.6.1.4.1.18.3.4.9.6.1.59
Specifies the role of this Logical Line. This attribute directs the Logical Line to be either a normal permanent synchronous connection, a Primary Rate ISDN 'D' channel or a Primary Rate ISDN 'B' channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER syncconnect(1), dchannel(2), bchannel(3)  

wfLogicalLineActiveCct 1.3.6.1.4.1.18.3.4.9.6.1.60
Active CCT number for this LogicalLine. Used in ISDN PRI to indicate the CCT of the current call in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLogicalLineActualRateAdaption 1.3.6.1.4.1.18.3.4.9.6.1.61
Indicates the current Rate Adaption in use. This may differ from the configured Rate Adaption in ISDN PRI applications. This attribute indicates the number of bits and their bit positions within the time-slot. 64k selection uses all 8 bits in the time-slot. The two 56k selections use 7 of the 8 bits in the time-slot. 56k_MSB does not use the most significant bit and 56k_LSB does not use the least significant bit in the time-slot. If the logical line is configured for DS0-A operation, rate adaptions of 9.6 Kbps and 19.2 Kbps may be configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER adaption64k(1), adaption56kmsb(2), adaption56klsb(3), adaption9dot6k(4), adaption19dot2k(5)  

wfLogicalLineBertMode 1.3.6.1.4.1.18.3.4.9.6.1.62
Enables BERT testing on a logical line level. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineBertTestPattern 1.3.6.1.4.1.18.3.4.9.6.1.63
Test pattern for BERT. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zeros(1), ones(2), qrss(3), two15(4), two15-inv(5), two20(6), two23(7), two23-inv(8)  

wfLogicalLineAcceptFracLoopCode 1.3.6.1.4.1.18.3.4.9.6.1.64
Allows logical line to accept Fractional T1 Loop Code. This feature is only supported by the QMCT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineDS0AStatus 1.3.6.1.4.1.18.3.4.9.6.1.65
Indicates logical line set to T1 DS0-A Subrates. This feature is only supported by the QMCT1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineNRZIEnable 1.3.6.1.4.1.18.3.4.9.6.1.66
Allows logical line to accept T1 NRZI encoding on logical Line. This feature is only supported by the QMRT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLogicalLineNRZIType 1.3.6.1.4.1.18.3.4.9.6.1.67
Defines logical line to T1 NRZI encoding as either Mark or Space on logical Line. This feature is only supported by the QMRT1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER space(1), mark(2)  

wfDs1E1FracTable 1.3.6.1.4.1.18.3.4.9.7
The DS1E1 fractional table identifies for each time-slot, the Logical Line to which the time-slot is currently bound.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FracEntry

wfDs1E1FracEntry 1.3.6.1.4.1.18.3.4.9.7.1
An entry in the DS1E1 Fractional Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FracEntry  

wfDs1E1FracDelete 1.3.6.1.4.1.18.3.4.9.7.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1FracPortLineNumber 1.3.6.1.4.1.18.3.4.9.7.1.2
Line number with a zero channel number field. Identifies the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FracNumber 1.3.6.1.4.1.18.3.4.9.7.1.3
The time slot to be assigned
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FracLogicalLineIndex 1.3.6.1.4.1.18.3.4.9.7.1.4
This time slot is assigned to the Logical Line identified by this attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1FracActualLogicalLineIndex 1.3.6.1.4.1.18.3.4.9.7.1.5
This time slot can be manipulated by ISDN PRI Multi-Rate service. This is the logical line to which the time slot is currently allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1CurrentTable 1.3.6.1.4.1.18.3.4.9.10
Current AT&T FDL stats table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1CurrentEntry

wfDs1E1CurrentEntry 1.3.6.1.4.1.18.3.4.9.10.1
An entry in the DS1E1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1CurrentEntry  

wfDs1E1CurrentPortLineNumber 1.3.6.1.4.1.18.3.4.9.10.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1CurrentESs 1.3.6.1.4.1.18.3.4.9.10.1.2
The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentSESs 1.3.6.1.4.1.18.3.4.9.10.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the current 15 minute interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentSEFSs 1.3.6.1.4.1.18.3.4.9.10.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentUASs 1.3.6.1.4.1.18.3.4.9.10.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentCSSs 1.3.6.1.4.1.18.3.4.9.10.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentPCVs 1.3.6.1.4.1.18.3.4.9.10.1.7
The number of Path Coding Violations encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentLESs 1.3.6.1.4.1.18.3.4.9.10.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the current 15 minute interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentBESs 1.3.6.1.4.1.18.3.4.9.10.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentDMs 1.3.6.1.4.1.18.3.4.9.10.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the current 15 minute interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentLCVs 1.3.6.1.4.1.18.3.4.9.10.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the current 15 minute interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentSASs 1.3.6.1.4.1.18.3.4.9.10.1.12
The number of seconds, within the current 15 minute interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentAISSs 1.3.6.1.4.1.18.3.4.9.10.1.13
The number of seconds, within the current 15 minute interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFCs 1.3.6.1.4.1.18.3.4.9.10.1.14
The number of Path Failure Count error events detected in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentTimeElapsed 1.3.6.1.4.1.18.3.4.9.10.1.15
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1CurrentValidIntervals 1.3.6.1.4.1.18.3.4.9.10.1.16
The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1CurrentValidFlag 1.3.6.1.4.1.18.3.4.9.10.1.17
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1IntervalTable 1.3.6.1.4.1.18.3.4.9.11
AT&T Interval stats
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1IntervalEntry

wfDs1E1IntervalEntry 1.3.6.1.4.1.18.3.4.9.11.1
An entry in the DS1E1 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1IntervalEntry  

wfDs1E1IntervalPortLineNumber 1.3.6.1.4.1.18.3.4.9.11.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1IntervalNumber 1.3.6.1.4.1.18.3.4.9.11.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1IntervalESs 1.3.6.1.4.1.18.3.4.9.11.1.3
The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalSESs 1.3.6.1.4.1.18.3.4.9.11.1.4
The number of Severely Errored Seconds encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalSEFSs 1.3.6.1.4.1.18.3.4.9.11.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalUASs 1.3.6.1.4.1.18.3.4.9.11.1.6
The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalCSSs 1.3.6.1.4.1.18.3.4.9.11.1.7
The number of Controlled Slip Seconds encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalPCVs 1.3.6.1.4.1.18.3.4.9.11.1.8
The number of Path Coding Violations encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalLESs 1.3.6.1.4.1.18.3.4.9.11.1.9
The number of Line Errored Seconds encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalBESs 1.3.6.1.4.1.18.3.4.9.11.1.10
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalDMs 1.3.6.1.4.1.18.3.4.9.11.1.11
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalLCVs 1.3.6.1.4.1.18.3.4.9.11.1.12
The number of Line Code Violations (LCVs) encountered by a DS1 interface in one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalSASs 1.3.6.1.4.1.18.3.4.9.11.1.13
The number of seconds, in one of the previous 15 minute intervals, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalAISSs 1.3.6.1.4.1.18.3.4.9.11.1.14
The number of seconds, in one of the previous 15 minute intervals, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFCs 1.3.6.1.4.1.18.3.4.9.11.1.15
The number of Path Failure Count error events detected one of the previous 15 minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalValidFlag 1.3.6.1.4.1.18.3.4.9.11.1.16
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1TotalTable 1.3.6.1.4.1.18.3.4.9.12
AT&T Total stats Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1TotalEntry

wfDs1E1TotalEntry 1.3.6.1.4.1.18.3.4.9.12.1
An entry in the DS1E1 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1TotalEntry  

wfDs1E1TotalPortLineNumber 1.3.6.1.4.1.18.3.4.9.12.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1TotalESs 1.3.6.1.4.1.18.3.4.9.12.1.2
The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalSESs 1.3.6.1.4.1.18.3.4.9.12.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalSEFSs 1.3.6.1.4.1.18.3.4.9.12.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalUASs 1.3.6.1.4.1.18.3.4.9.12.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalCSSs 1.3.6.1.4.1.18.3.4.9.12.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalPCVs 1.3.6.1.4.1.18.3.4.9.12.1.7
The number of Path Coding Violations encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalLESs 1.3.6.1.4.1.18.3.4.9.12.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalBESs 1.3.6.1.4.1.18.3.4.9.12.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalDMs 1.3.6.1.4.1.18.3.4.9.12.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalLCVs 1.3.6.1.4.1.18.3.4.9.12.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalSASs 1.3.6.1.4.1.18.3.4.9.12.1.12
The number of seconds, in the previous 24-hour interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalAISSs 1.3.6.1.4.1.18.3.4.9.12.1.13
The number of seconds, in the previous 24-hour interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFCs 1.3.6.1.4.1.18.3.4.9.12.1.14
The number of Path Failure Count error events detected in the previous 24-hour interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalValidFlag 1.3.6.1.4.1.18.3.4.9.12.1.15
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1AnsiTable 1.3.6.1.4.1.18.3.4.8.13
ANSI Statistics line record - This table contains the performance parameters for the ANSI register set
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1AnsiEntry

wfDs1E1AnsiEntry 1.3.6.1.4.1.18.3.4.8.13.1
An entry in the DS1E1 Ansi table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1AnsiEntry  

wfDs1E1AnsiPortLineNumber 1.3.6.1.4.1.18.3.4.8.13.1.1
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1AnsiCRCCounts 1.3.6.1.4.1.18.3.4.8.13.1.2
Counts CRC-6 error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiBPVCounts 1.3.6.1.4.1.18.3.4.8.13.1.3
Counts bipolar violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiOOFCounts 1.3.6.1.4.1.18.3.4.8.13.1.4
Counts out-of-frame error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiFECounts 1.3.6.1.4.1.18.3.4.8.13.1.5
Counts errors in the FPS framing pattern
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiESCounts 1.3.6.1.4.1.18.3.4.8.13.1.6
Counts errorred seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiSESCounts 1.3.6.1.4.1.18.3.4.8.13.1.7
Counts severly errorred seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiUASCounts 1.3.6.1.4.1.18.3.4.8.13.1.8
counts unavailable seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMR0Counts 1.3.6.1.4.1.18.3.4.8.13.1.9
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMR1Counts 1.3.6.1.4.1.18.3.4.8.13.1.10
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMR2Counts 1.3.6.1.4.1.18.3.4.8.13.1.11
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMR3Counts 1.3.6.1.4.1.18.3.4.8.13.1.12
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMESCounts 1.3.6.1.4.1.18.3.4.8.13.1.13
Counts errorred seconds as reported in the Performance report messages
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMSESCounts 1.3.6.1.4.1.18.3.4.8.13.1.14
Counts severely errorred seconds as reported in the Performance report messages
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1AnsiPRMECounts 1.3.6.1.4.1.18.3.4.8.13.1.15
Counts Performance report messages that are received in error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1BertStatsTable 1.3.6.1.4.1.18.3.4.9.14
BERT Counter line record - This table contains the statistics for the BERT tester.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1BertStatsEntry

wfDs1E1BertStatsEntry 1.3.6.1.4.1.18.3.4.9.14.1
An entry in the DS1E1 Bert Stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1BertStatsEntry  

wfDs1E1BertStatsPortLineNumber 1.3.6.1.4.1.18.3.4.9.14.1.1
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1BertStatsBitErrors 1.3.6.1.4.1.18.3.4.9.14.1.2
Bit error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1BertStatsBits 1.3.6.1.4.1.18.3.4.9.14.1.3
Bit counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1CurrentFramerStatsTable 1.3.6.1.4.1.18.3.4.9.15
Framer stats line record - This table contains the statistics for the Framer tester.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1CurrentFramerStatsEntry

wfDs1E1CurrentFramerStatsEntry 1.3.6.1.4.1.18.3.4.9.15.1
An entry in the DS1E1 CurrentFramer Stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1CurrentFramerStatsEntry  

wfDs1E1CurrentFramerStatsPortLineNumber 1.3.6.1.4.1.18.3.4.9.15.1.1
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1CurrentFramerStatsMediaType 1.3.6.1.4.1.18.3.4.9.15.1.2
The media type is either T1 or E1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

wfDs1E1CurrentFramerStatsBpvCounts 1.3.6.1.4.1.18.3.4.9.15.1.3
bipolar violations counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsCrc4Counts 1.3.6.1.4.1.18.3.4.9.15.1.4
CRC4 error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsFebeCounts 1.3.6.1.4.1.18.3.4.9.15.1.5
Far End Block Error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsOofCounts 1.3.6.1.4.1.18.3.4.9.15.1.6
Out of frame error counts. Out of frame is declared when at least two of four (or five) consecutive framing bits are in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsFeCounts 1.3.6.1.4.1.18.3.4.9.15.1.7
Framing error counts. In ESF mode this is the number of errored superframes while in SF mode it is the number of incorrect framing bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsLossFrameFailures 1.3.6.1.4.1.18.3.4.9.15.1.8
Loss of frame failures. These occur when an out of frame event or carrier loss happens
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsLossSignalFailures 1.3.6.1.4.1.18.3.4.9.15.1.9
Loss of Signal failure happen when receive carrier is lost
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsAlarmIndicationFailures 1.3.6.1.4.1.18.3.4.9.15.1.10
Alarm Indication signal Failures occur when 2 consecutive frames have less than 3 zeros (total) in the data stream.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1CurrentFramerStatsRemoteAlarmFailures 1.3.6.1.4.1.18.3.4.9.15.1.11
Remote alarm failure happen when the yellow alarm is detected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsTable 1.3.6.1.4.1.18.3.4.9.16
Total framer stats line record - This table contains the statistics for the Framer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1TotalFramerStatsEntry

wfDs1E1TotalFramerStatsEntry 1.3.6.1.4.1.18.3.4.9.16.1
An entry in the DS1E1 TotalFramer Stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1TotalFramerStatsEntry  

wfDs1E1TotalFramerStatsPortLineNumber 1.3.6.1.4.1.18.3.4.9.16.1.1
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1TotalFramerStatsMediaType 1.3.6.1.4.1.18.3.4.9.16.1.2
bipolar violations counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

wfDs1E1TotalFramerStatsValidIntervals 1.3.6.1.4.1.18.3.4.9.16.1.3
The number of valid 15 minutes intervals in the last 24-hour period
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsBpvCounts 1.3.6.1.4.1.18.3.4.9.16.1.4
bipolar violations counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsCrc4Counts 1.3.6.1.4.1.18.3.4.9.16.1.5
CRC4 error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsFebeCounts 1.3.6.1.4.1.18.3.4.9.16.1.6
Far End Block Error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsOofCounts 1.3.6.1.4.1.18.3.4.9.16.1.7
Out of frame error counts. Out of frame is declared when at least two of four (or five) consecutive framing bits are in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsFeCounts 1.3.6.1.4.1.18.3.4.9.16.1.8
Framing error counts. In ESF mode this is the number of errored superframes while in SF mode it is the number of incorrect framing bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsLossFrameFailures 1.3.6.1.4.1.18.3.4.9.16.1.9
Loss of frame failures. These occur when an out of frame event or carrier loss happens
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsLossSignalFailures 1.3.6.1.4.1.18.3.4.9.16.1.10
Loss of Signal failure happen when receive carrier is lost
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsAlarmIndicationFailures 1.3.6.1.4.1.18.3.4.9.16.1.11
Alarm Indication signal Failures occur when 2 consecutive frames have less than 3 zeros (total) in the data stream.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1TotalFramerStatsRemoteAlarmFailures 1.3.6.1.4.1.18.3.4.9.16.1.12
Remote alarm failure happen when the yellow alarm is detected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsTable 1.3.6.1.4.1.18.3.4.9.17
Interval Framer stats line record - This table contains the statistics for the Framer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1IntervalFramerStatsEntry

wfDs1E1IntervalFramerStatsEntry 1.3.6.1.4.1.18.3.4.9.17.1
An entry in the DS1E1 IntervalFramer Stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1IntervalFramerStatsEntry  

wfDs1E1IntervalFramerStatsPortLineNumber 1.3.6.1.4.1.18.3.4.9.17.1.1
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1IntervalFramerStatsIntervalNumber 1.3.6.1.4.1.18.3.4.9.17.1.2
Instance ID interval number, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1IntervalFramerStatsMediaType 1.3.6.1.4.1.18.3.4.9.17.1.3
Media Type, T1 or E1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

wfDs1E1IntervalFramerStatsBpvCounts 1.3.6.1.4.1.18.3.4.9.17.1.4
bipolar violations counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsCrc4Counts 1.3.6.1.4.1.18.3.4.9.17.1.5
CRC4 error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsFebeCounts 1.3.6.1.4.1.18.3.4.9.17.1.6
Far End Block Error counter
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsOofCounts 1.3.6.1.4.1.18.3.4.9.17.1.7
Out of frame error counts. Out of frame is declared when at least two of four (or five) consecutive framing bits are in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsFeCounts 1.3.6.1.4.1.18.3.4.9.17.1.8
Framing error counts. In ESF mode this is the number of errored superframes while in SF mode it is the number of incorrect framing bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsLossFrameFailures 1.3.6.1.4.1.18.3.4.9.17.1.9
Loss of frame failures. These occur when an out of frame event or carrier loss happens
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsLossSignalFailures 1.3.6.1.4.1.18.3.4.9.17.1.10
Loss of Signal failure happen when receive carrier is lost
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsAlarmIndicationFailures 1.3.6.1.4.1.18.3.4.9.17.1.11
Alarm Indication signal Failures occur when 2 consecutive frames have less than 3 zeros (total) in the data stream.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1IntervalFramerStatsRemoteAlarmFailures 1.3.6.1.4.1.18.3.4.9.17.1.12
Remote alarm failure happen when the yellow alarm is detected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1ClockTable 1.3.6.1.4.1.18.3.4.9.18
DS1E1 clock record - Contains Clock parameters supporting the QMCT1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1ClockEntry

wfDs1E1ClockEntry 1.3.6.1.4.1.18.3.4.9.18.1
An entry in the DS1E1 clock table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1ClockEntry  

wfDs1E1ClockDelete 1.3.6.1.4.1.18.3.4.9.18.1.1
Create/Delete attribute
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1ClockPortLineNumber 1.3.6.1.4.1.18.3.4.9.18.1.2
The index ID for this record. It is the line number assigned to a port in the wfDs1E1PortMapEntry for a port.connector pair. Its channel field should be 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ClockPrimaryClock 1.3.6.1.4.1.18.3.4.9.18.1.3
Specifies the primary source for transmit timing for this port. The options for timing source are internal timing source, loop timing from either port and an external timing source. Note that the bit defines are equal to the Timing Register bit definitions plus 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop1(3), loop2(4), loop3(5), loop4(6)  

wfDs1E1ClockSecondaryClock 1.3.6.1.4.1.18.3.4.9.18.1.4
Specifies the secondary source for transmit timing for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop1(3), loop2(4), loop3(5), loop4(6)  

wfDs1E1ClockCurrentClock 1.3.6.1.4.1.18.3.4.9.18.1.5
Specifies the current source for transmit timing for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internal(1), external(2), loop1(3), loop2(4), loop3(5), loop4(6)  

wfDs1E1ClockLoopClockOperational 1.3.6.1.4.1.18.3.4.9.18.1.6
Specifies this ports Loop Clock Status, PRESENT (UP) or NOTPRESENT (DOWN).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1ClockExtClockOperational 1.3.6.1.4.1.18.3.4.9.18.1.7
Indicates whether the External clock is operational.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), notpresent(2)  

wfDs1E1LineCfgTable 1.3.6.1.4.1.18.3.4.9.21
Contains configuration parameters for Channel specific Fractional T1/E1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1LineCfgEntry

wfDs1E1LineCfgEntry 1.3.6.1.4.1.18.3.4.9.21.1
An entry in the LOGICAL_LINE table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1LineCfgEntry  

wfDs1E1LineCfgDelete 1.3.6.1.4.1.18.3.4.9.21.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1LineCfgDisable 1.3.6.1.4.1.18.3.4.9.21.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1LineCfgState 1.3.6.1.4.1.18.3.4.9.21.1.3
Line Driver state variable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), lmiwait(4), loopback(5), linedieing(6), linedead(7), remoteloop(8), remotedeaf(9), bert(10), hwfrac(11), priWait(12), quePkgWait(13), queMisCfg(14), notpresent(20)  

wfDs1E1LineLastChange 1.3.6.1.4.1.18.3.4.9.21.1.4
The value of sysUpTime at the time the interface entered its current operational state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfDs1E1LineCfgPortLineNumber 1.3.6.1.4.1.18.3.4.9.21.1.5
Instance ID PortLineNumber, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgIndex 1.3.6.1.4.1.18.3.4.9.21.1.6
Index for this line instance, filled in by driver. The index corresponds to the position of the circuit on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgIfIndex 1.3.6.1.4.1.18.3.4.9.21.1.7
IfTable Index for this line instance, filled in by driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgCct 1.3.6.1.4.1.18.3.4.9.21.1.8
Circuit number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgLineNumber 1.3.6.1.4.1.18.3.4.9.21.1.9
LineNumber for this logical line instance. This is the same line number contained in the PORT_TABLE with the channel field nonzero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgQosServicePkg 1.3.6.1.4.1.18.3.4.9.21.1.10
Queue Service Package to be used for this line
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgTimeSlotAssign 1.3.6.1.4.1.18.3.4.9.21.1.11
Bitmask of timeslot(s) assigned to this line MSB == Bit 31, LSB == Bit 0 TimeSlot 1 == Bit 1 TimeSlot 24 == Bit 24 (T1) TimeSlot 31 == Bit 31 (E1)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineCfgActualTimeSlotAssign 1.3.6.1.4.1.18.3.4.9.21.1.12
Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 31 used by the channel
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfDs1E1LineCfgWanProtocol 1.3.6.1.4.1.18.3.4.9.21.1.13
WAN protocol selection is provided via this parameter. The supported protocols can be selected per circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), passthru(2), ppp(3), smds(4), framerelay(5), x25(6), switch(7), sw(8), atm(9), lapb(10), sdlc(11)  

wfDs1E1LineCfgRateAdaption 1.3.6.1.4.1.18.3.4.9.21.1.14
Determines the number of bits and their bit positions within the time-slot. 64k selection uses all 8 bits in the time-slot. The two 56k selections use 7 of the 8 bits in the time-slot. 56k_MSB does not use the most significant bit and 56k_LSB does not use the least significant bit in the time-slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adaption64k(1), adaption56klsb(3)  

wfDs1E1LineCfgIFTF 1.3.6.1.4.1.18.3.4.9.21.1.15
Determines the Interframe time fill character to be transmitted by the HDLC Controller. In case of IFTF_FLAGS, 0x7E is sent and in case of IFTF_IDLES 0xff is sent as the interframe timefill characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER flags(1), idles(2)  

wfDs1E1LineCfgCRCSize 1.3.6.1.4.1.18.3.4.9.21.1.16
Determines the CRC Size. When CRC32 is selected a 32 bit CRC is appended to the frame being transmitted and a 32 bit CRC check is performed on the received frame. When CRC16 is selected, a 16 bit CRC is appended to the transmitted frame and a 16 bit CRC is performed. on the received frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crc32(1), crc16(2)  

wfDs1E1LineCfgMtu 1.3.6.1.4.1.18.3.4.9.21.1.17
Specifies the largest frame size that can be received by the logical line. Anything larger than the MTU will be discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..4608  

wfDs1E1LineCfgBertMode 1.3.6.1.4.1.18.3.4.9.21.1.18
Enables Bit Error Rate Testing (BERT) on a logical line level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1LineCfgBertTestPattern 1.3.6.1.4.1.18.3.4.9.21.1.19
When a line is in BERT mode, it is capable of generating a set of known patterns. This paramater selects between those patterns
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zeros(1), ones(2), qrss(3), two15(4), two15-inv(5), two20(6), two23(7), two23-inv(8)  

wfDs1E1LineCfgFractionalLoopback 1.3.6.1.4.1.18.3.4.9.21.1.20
Any Ds1E1 Line on this T1/E1 port is capable of being put into loopback through hardware, i.e. data coming into that circuit from the wire is mirrorred back onto the wire. This parameter enables or disables this loopback feature on any circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1LineCfgAcceptFracLoopCode 1.3.6.1.4.1.18.3.4.9.21.1.21
Allows logical line to accept Fractional T1 Loop Code sent from a Remote Device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDs1E1LineCfgManagerMethod 1.3.6.1.4.1.18.3.4.9.21.1.22
This attribute has no affect on the Hardware configuration. This attribute is purely for any Network Management Tool to determine whether it configured the Logical Line as a Clear Channel T1 or as a Fractional T1 with Timeslots.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER timeslots(1), t1(2)  

wfDs1E1LineStatTable 1.3.6.1.4.1.18.3.4.9.22
Contains statistics for Channel specific Fractional T1/E1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1LineStatEntry

wfDs1E1LineStatEntry 1.3.6.1.4.1.18.3.4.9.22.1
An entry in the LOGICAL_LINE table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1LineStatEntry  

wfDs1E1LineStatPortLineNumber 1.3.6.1.4.1.18.3.4.9.22.1.1
Instance ID PortLineNumber, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineStatIndex 1.3.6.1.4.1.18.3.4.9.22.1.2
Index for this line instance, filled in by driver. The index corresponds to the position of the circuit, from 1 to 31, on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineStatRxOctets 1.3.6.1.4.1.18.3.4.9.22.1.3
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatTxOctets 1.3.6.1.4.1.18.3.4.9.22.1.4
Number of octets transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxFrames 1.3.6.1.4.1.18.3.4.9.22.1.5
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatTxFrames 1.3.6.1.4.1.18.3.4.9.22.1.6
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxErrors 1.3.6.1.4.1.18.3.4.9.22.1.7
Number of receive errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatTxErrors 1.3.6.1.4.1.18.3.4.9.22.1.8
Number of transmission errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxDropPackets 1.3.6.1.4.1.18.3.4.9.22.1.9
Number of Rx frames dropped
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatTxDropPackets 1.3.6.1.4.1.18.3.4.9.22.1.10
Number of Tx frames dropped
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatTxUnderflows 1.3.6.1.4.1.18.3.4.9.22.1.11
Number of Tx frames dropped due to Transmit underflow
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxOverflows 1.3.6.1.4.1.18.3.4.9.22.1.12
Number of Rx frames dropped due to Receive overflow
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxShortFrames 1.3.6.1.4.1.18.3.4.9.22.1.13
Number of short frames received whose length is either 1 or 2 data bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxCRCErrors 1.3.6.1.4.1.18.3.4.9.22.1.14
CRC error received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxNonOctetBits 1.3.6.1.4.1.18.3.4.9.22.1.15
Non-Octet bits received in frame
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxLongFrames 1.3.6.1.4.1.18.3.4.9.22.1.16
Frame longer than MFL received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineStatRxAbortFrames 1.3.6.1.4.1.18.3.4.9.22.1.17
Aborted frame received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1DayCurrentTable 1.3.6.1.4.1.18.3.4.9.24
Current AT&T FDL stats table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1DayCurrentEntry

wfDs1E1DayCurrentEntry 1.3.6.1.4.1.18.3.4.9.24.1
An entry in the DS1E1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1DayCurrentEntry  

wfDs1E1DayCurrentPortLineNumber 1.3.6.1.4.1.18.3.4.9.24.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayCurrentESs 1.3.6.1.4.1.18.3.4.9.24.1.2
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentSESs 1.3.6.1.4.1.18.3.4.9.24.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentSEFSs 1.3.6.1.4.1.18.3.4.9.24.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentUASs 1.3.6.1.4.1.18.3.4.9.24.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentCSSs 1.3.6.1.4.1.18.3.4.9.24.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentPCVs 1.3.6.1.4.1.18.3.4.9.24.1.7
The number of Path Coding Violations encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentLESs 1.3.6.1.4.1.18.3.4.9.24.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentBESs 1.3.6.1.4.1.18.3.4.9.24.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentDMs 1.3.6.1.4.1.18.3.4.9.24.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentLCVs 1.3.6.1.4.1.18.3.4.9.24.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentSASs 1.3.6.1.4.1.18.3.4.9.24.1.12
The number of seconds, within the current day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentAISSs 1.3.6.1.4.1.18.3.4.9.24.1.13
The number of seconds, within the current day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentFCs 1.3.6.1.4.1.18.3.4.9.24.1.14
The number of Path Failure Count error events detected in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayCurrentTimeElapsed 1.3.6.1.4.1.18.3.4.9.24.1.15
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayCurrentValidIntervals 1.3.6.1.4.1.18.3.4.9.24.1.16
The number of previous intervals for which valid data was collected. The value will be 8 unless the interface was brought on-line within the last 8 days, in which case the value will be the number of complete day intervals the since interface has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayCurrentValidFlag 1.3.6.1.4.1.18.3.4.9.24.1.17
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1DayIntervalTable 1.3.6.1.4.1.18.3.4.9.25
AT&T Interval stats
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1DayIntervalEntry

wfDs1E1DayIntervalEntry 1.3.6.1.4.1.18.3.4.9.25.1
An entry in the DS1E1 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1DayIntervalEntry  

wfDs1E1DayIntervalPortLineNumber 1.3.6.1.4.1.18.3.4.9.25.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayIntervalNumber 1.3.6.1.4.1.18.3.4.9.25.1.2
A number between 1 and 8, where 1 is the most recently completed day interval and 8 is the least recently completed day interval (assuming that all 8 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayIntervalESs 1.3.6.1.4.1.18.3.4.9.25.1.3
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalSESs 1.3.6.1.4.1.18.3.4.9.25.1.4
The number of Severely Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalSEFSs 1.3.6.1.4.1.18.3.4.9.25.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalUASs 1.3.6.1.4.1.18.3.4.9.25.1.6
The number of Unavailable Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalCSSs 1.3.6.1.4.1.18.3.4.9.25.1.7
The number of Controlled Slip Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalPCVs 1.3.6.1.4.1.18.3.4.9.25.1.8
The number of Path Coding Violations encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalLESs 1.3.6.1.4.1.18.3.4.9.25.1.9
The number of Line Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalBESs 1.3.6.1.4.1.18.3.4.9.25.1.10
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalDMs 1.3.6.1.4.1.18.3.4.9.25.1.11
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalLCVs 1.3.6.1.4.1.18.3.4.9.25.1.12
The number of Line Code Violations (LCVs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalSASs 1.3.6.1.4.1.18.3.4.9.25.1.13
The number of seconds, in one of the previous day intervals, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalAISSs 1.3.6.1.4.1.18.3.4.9.25.1.14
The number of seconds, in one of the previous day intervals, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalFCs 1.3.6.1.4.1.18.3.4.9.25.1.15
The number of Path Failure Count error events detected one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayIntervalValidFlag 1.3.6.1.4.1.18.3.4.9.25.1.16
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1DayTotalTable 1.3.6.1.4.1.18.3.4.9.26
AT&T Total stats Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1DayTotalEntry

wfDs1E1DayTotalEntry 1.3.6.1.4.1.18.3.4.9.26.1
An entry in the DS1E1 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1DayTotalEntry  

wfDs1E1DayTotalPortLineNumber 1.3.6.1.4.1.18.3.4.9.26.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayTotalESs 1.3.6.1.4.1.18.3.4.9.26.1.2
The number of Errored Seconds, encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalSESs 1.3.6.1.4.1.18.3.4.9.26.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalSEFSs 1.3.6.1.4.1.18.3.4.9.26.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalUASs 1.3.6.1.4.1.18.3.4.9.26.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalCSSs 1.3.6.1.4.1.18.3.4.9.26.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalPCVs 1.3.6.1.4.1.18.3.4.9.26.1.7
The number of Path Coding Violations encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalLESs 1.3.6.1.4.1.18.3.4.9.26.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalBESs 1.3.6.1.4.1.18.3.4.9.26.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalDMs 1.3.6.1.4.1.18.3.4.9.26.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalLCVs 1.3.6.1.4.1.18.3.4.9.26.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalSASs 1.3.6.1.4.1.18.3.4.9.26.1.12
The number of seconds, in the previous 8 day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalAISSs 1.3.6.1.4.1.18.3.4.9.26.1.13
The number of seconds, in the previous 8 day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalFCs 1.3.6.1.4.1.18.3.4.9.26.1.14
The number of Path Failure Count error events detected in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1DayTotalValidFlag 1.3.6.1.4.1.18.3.4.9.26.1.15
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndCurrentTable 1.3.6.1.4.1.18.3.4.9.27
Current AT&T FDL stats table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndCurrentEntry

wfDs1E1FarEndCurrentEntry 1.3.6.1.4.1.18.3.4.9.27.1
An entry in the DS1E1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndCurrentEntry  

wfDs1E1FarEndCurrentPortLineNumber 1.3.6.1.4.1.18.3.4.9.27.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndCurrentESs 1.3.6.1.4.1.18.3.4.9.27.1.2
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentSESs 1.3.6.1.4.1.18.3.4.9.27.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentSEFSs 1.3.6.1.4.1.18.3.4.9.27.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentUASs 1.3.6.1.4.1.18.3.4.9.27.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentCSSs 1.3.6.1.4.1.18.3.4.9.27.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentPCVs 1.3.6.1.4.1.18.3.4.9.27.1.7
The number of Path Coding Violations encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentLESs 1.3.6.1.4.1.18.3.4.9.27.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentBESs 1.3.6.1.4.1.18.3.4.9.27.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentDMs 1.3.6.1.4.1.18.3.4.9.27.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentLCVs 1.3.6.1.4.1.18.3.4.9.27.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentSASs 1.3.6.1.4.1.18.3.4.9.27.1.12
The number of seconds, within the current day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentAISSs 1.3.6.1.4.1.18.3.4.9.27.1.13
The number of seconds, within the current day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentFCs 1.3.6.1.4.1.18.3.4.9.27.1.14
The number of Path Failure Count error events detected in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndCurrentTimeElapsed 1.3.6.1.4.1.18.3.4.9.27.1.15
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndCurrentValidIntervals 1.3.6.1.4.1.18.3.4.9.27.1.16
The number of previous intervals for which valid data was collected. The value will be 8 unless the interface was brought on-line within the last 8 days, in which case the value will be the number of complete day intervals the since interface has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndCurrentValidFlag 1.3.6.1.4.1.18.3.4.9.27.1.17
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndIntervalTable 1.3.6.1.4.1.18.3.4.9.28
AT&T Interval stats
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndIntervalEntry

wfDs1E1FarEndIntervalEntry 1.3.6.1.4.1.18.3.4.9.28.1
An entry in the DS1E1 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndIntervalEntry  

wfDs1E1FarEndIntervalPortLineNumber 1.3.6.1.4.1.18.3.4.9.28.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndIntervalNumber 1.3.6.1.4.1.18.3.4.9.28.1.2
A number between 1 and 8, where 1 is the most recently completed day interval and 8 is the least recently completed day interval (assuming that all 8 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndIntervalESs 1.3.6.1.4.1.18.3.4.9.28.1.3
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalSESs 1.3.6.1.4.1.18.3.4.9.28.1.4
The number of Severely Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalSEFSs 1.3.6.1.4.1.18.3.4.9.28.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalUASs 1.3.6.1.4.1.18.3.4.9.28.1.6
The number of Unavailable Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalCSSs 1.3.6.1.4.1.18.3.4.9.28.1.7
The number of Controlled Slip Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalPCVs 1.3.6.1.4.1.18.3.4.9.28.1.8
The number of Path Coding Violations encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalLESs 1.3.6.1.4.1.18.3.4.9.28.1.9
The number of Line Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalBESs 1.3.6.1.4.1.18.3.4.9.28.1.10
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalDMs 1.3.6.1.4.1.18.3.4.9.28.1.11
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalLCVs 1.3.6.1.4.1.18.3.4.9.28.1.12
The number of Line Code Violations (LCVs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalSASs 1.3.6.1.4.1.18.3.4.9.28.1.13
The number of seconds, in one of the previous day intervals, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalAISSs 1.3.6.1.4.1.18.3.4.9.28.1.14
The number of seconds, in one of the previous day intervals, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalFCs 1.3.6.1.4.1.18.3.4.9.28.1.15
The number of Path Failure Count error events detected one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndIntervalValidFlag 1.3.6.1.4.1.18.3.4.9.28.1.16
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndTotalTable 1.3.6.1.4.1.18.3.4.9.29
AT&T Total stats Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndTotalEntry

wfDs1E1FarEndTotalEntry 1.3.6.1.4.1.18.3.4.9.29.1
An entry in the DS1E1 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndTotalEntry  

wfDs1E1FarEndTotalPortLineNumber 1.3.6.1.4.1.18.3.4.9.29.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndTotalESs 1.3.6.1.4.1.18.3.4.9.29.1.2
The number of Errored Seconds, encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalSESs 1.3.6.1.4.1.18.3.4.9.29.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalSEFSs 1.3.6.1.4.1.18.3.4.9.29.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalUASs 1.3.6.1.4.1.18.3.4.9.29.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalCSSs 1.3.6.1.4.1.18.3.4.9.29.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalPCVs 1.3.6.1.4.1.18.3.4.9.29.1.7
The number of Path Coding Violations encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalLESs 1.3.6.1.4.1.18.3.4.9.29.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalBESs 1.3.6.1.4.1.18.3.4.9.29.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalDMs 1.3.6.1.4.1.18.3.4.9.29.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalLCVs 1.3.6.1.4.1.18.3.4.9.29.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalSASs 1.3.6.1.4.1.18.3.4.9.29.1.12
The number of seconds, in the previous 8 day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalAISSs 1.3.6.1.4.1.18.3.4.9.29.1.13
The number of seconds, in the previous 8 day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalFCs 1.3.6.1.4.1.18.3.4.9.29.1.14
The number of Path Failure Count error events detected in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndTotalValidFlag 1.3.6.1.4.1.18.3.4.9.29.1.15
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndDayCurrentTable 1.3.6.1.4.1.18.3.4.9.30
Current AT&T FDL stats table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndDayCurrentEntry

wfDs1E1FarEndDayCurrentEntry 1.3.6.1.4.1.18.3.4.9.30.1
An entry in the DS1E1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndDayCurrentEntry  

wfDs1E1FarEndDayCurrentPortLineNumber 1.3.6.1.4.1.18.3.4.9.30.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayCurrentESs 1.3.6.1.4.1.18.3.4.9.30.1.2
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentSESs 1.3.6.1.4.1.18.3.4.9.30.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentSEFSs 1.3.6.1.4.1.18.3.4.9.30.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentUASs 1.3.6.1.4.1.18.3.4.9.30.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentCSSs 1.3.6.1.4.1.18.3.4.9.30.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentPCVs 1.3.6.1.4.1.18.3.4.9.30.1.7
The number of Path Coding Violations encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentLESs 1.3.6.1.4.1.18.3.4.9.30.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentBESs 1.3.6.1.4.1.18.3.4.9.30.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentDMs 1.3.6.1.4.1.18.3.4.9.30.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentLCVs 1.3.6.1.4.1.18.3.4.9.30.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the current day interval.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentSASs 1.3.6.1.4.1.18.3.4.9.30.1.12
The number of seconds, within the current day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentAISSs 1.3.6.1.4.1.18.3.4.9.30.1.13
The number of seconds, within the current day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentFCs 1.3.6.1.4.1.18.3.4.9.30.1.14
The number of Path Failure Count error events detected in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayCurrentTimeElapsed 1.3.6.1.4.1.18.3.4.9.30.1.15
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayCurrentValidIntervals 1.3.6.1.4.1.18.3.4.9.30.1.16
The number of previous intervals for which valid data was collected. The value will be 8 unless the interface was brought on-line within the last 8 days, in which case the value will be the number of complete day intervals the since interface has been online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayCurrentValidFlag 1.3.6.1.4.1.18.3.4.9.30.1.17
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndDayIntervalTable 1.3.6.1.4.1.18.3.4.9.31
AT&T Interval stats
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndDayIntervalEntry

wfDs1E1FarEndDayIntervalEntry 1.3.6.1.4.1.18.3.4.9.31.1
An entry in the DS1E1 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndDayIntervalEntry  

wfDs1E1FarEndDayIntervalPortLineNumber 1.3.6.1.4.1.18.3.4.9.31.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayIntervalNumber 1.3.6.1.4.1.18.3.4.9.31.1.2
A number between 1 and 8, where 1 is the most recently completed day interval and 8 is the least recently completed day interval (assuming that all 8 intervals are valid).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayIntervalESs 1.3.6.1.4.1.18.3.4.9.31.1.3
The number of Errored Seconds, encountered by a DS1 interface in the current day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalSESs 1.3.6.1.4.1.18.3.4.9.31.1.4
The number of Severely Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalSEFSs 1.3.6.1.4.1.18.3.4.9.31.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalUASs 1.3.6.1.4.1.18.3.4.9.31.1.6
The number of Unavailable Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalCSSs 1.3.6.1.4.1.18.3.4.9.31.1.7
The number of Controlled Slip Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalPCVs 1.3.6.1.4.1.18.3.4.9.31.1.8
The number of Path Coding Violations encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalLESs 1.3.6.1.4.1.18.3.4.9.31.1.9
The number of Line Errored Seconds encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalBESs 1.3.6.1.4.1.18.3.4.9.31.1.10
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalDMs 1.3.6.1.4.1.18.3.4.9.31.1.11
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalLCVs 1.3.6.1.4.1.18.3.4.9.31.1.12
The number of Line Code Violations (LCVs) encountered by a DS1 interface in one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalSASs 1.3.6.1.4.1.18.3.4.9.31.1.13
The number of seconds, in one of the previous day intervals, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalAISSs 1.3.6.1.4.1.18.3.4.9.31.1.14
The number of seconds, in one of the previous day intervals, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalFCs 1.3.6.1.4.1.18.3.4.9.31.1.15
The number of Path Failure Count error events detected one of the previous day intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayIntervalValidFlag 1.3.6.1.4.1.18.3.4.9.31.1.16
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1FarEndDayTotalTable 1.3.6.1.4.1.18.3.4.9.32
AT&T Total stats Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndDayTotalEntry

wfDs1E1FarEndDayTotalEntry 1.3.6.1.4.1.18.3.4.9.32.1
An entry in the DS1E1 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndDayTotalEntry  

wfDs1E1FarEndDayTotalPortLineNumber 1.3.6.1.4.1.18.3.4.9.32.1.1
The instance ID that identifies the port. The port line number with a zero channel number field as found in the port map table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayTotalESs 1.3.6.1.4.1.18.3.4.9.32.1.2
The number of Errored Seconds, encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalSESs 1.3.6.1.4.1.18.3.4.9.32.1.3
The number of Severely Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalSEFSs 1.3.6.1.4.1.18.3.4.9.32.1.4
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalUASs 1.3.6.1.4.1.18.3.4.9.32.1.5
The number of Unavailable Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalCSSs 1.3.6.1.4.1.18.3.4.9.32.1.6
The number of Controlled Slip Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalPCVs 1.3.6.1.4.1.18.3.4.9.32.1.7
The number of Path Coding Violations encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalLESs 1.3.6.1.4.1.18.3.4.9.32.1.8
The number of Line Errored Seconds encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalBESs 1.3.6.1.4.1.18.3.4.9.32.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalDMs 1.3.6.1.4.1.18.3.4.9.32.1.10
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalLCVs 1.3.6.1.4.1.18.3.4.9.32.1.11
The number of Line Code Violations (LCVs) encountered by a DS1 interface in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalSASs 1.3.6.1.4.1.18.3.4.9.32.1.12
The number of seconds, in the previous 8 day interval, containing one or more SEFs or AIS defects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalAISSs 1.3.6.1.4.1.18.3.4.9.32.1.13
The number of seconds, in the previous 8 day interval, containing one or more AIS defect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalFCs 1.3.6.1.4.1.18.3.4.9.32.1.14
The number of Path Failure Count error events detected in the previous 8 day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayTotalValidFlag 1.3.6.1.4.1.18.3.4.9.32.1.15
Indicates whether this interval reported by the Mib Table is valid or invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfDs1E1ThrAlrtTable 1.3.6.1.4.1.18.3.4.9.33
Current statistics Alarm Threshold Crossing table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1ThrAlrtEntry

wfDs1E1ThrAlrtEntry 1.3.6.1.4.1.18.3.4.9.33.1
An entry in the DS1E1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1ThrAlrtEntry  

wfDs1E1ThrAlrtDelete 1.3.6.1.4.1.18.3.4.9.33.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1ThrAlrtPortLineNumber 1.3.6.1.4.1.18.3.4.9.33.1.2
The instance ID that identifies the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1ThrAlrtESs 1.3.6.1.4.1.18.3.4.9.33.1.3
The number of Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtSESs 1.3.6.1.4.1.18.3.4.9.33.1.4
The number of Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtSEFSs 1.3.6.1.4.1.18.3.4.9.33.1.5
The number of Severely Errored Framing Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtUASs 1.3.6.1.4.1.18.3.4.9.33.1.6
The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtCSSs 1.3.6.1.4.1.18.3.4.9.33.1.7
The number of Controlled Slip Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtPCVs 1.3.6.1.4.1.18.3.4.9.33.1.8
The number of Path Coding Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtLESs 1.3.6.1.4.1.18.3.4.9.33.1.9
The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtBESs 1.3.6.1.4.1.18.3.4.9.33.1.10
The number of Bursty Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtDMs 1.3.6.1.4.1.18.3.4.9.33.1.11
The number of Degraded Minutes which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtLCVs 1.3.6.1.4.1.18.3.4.9.33.1.12
The number of Line Code Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtSASs 1.3.6.1.4.1.18.3.4.9.33.1.13
The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtAISSs 1.3.6.1.4.1.18.3.4.9.33.1.14
The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1ThrAlrtFCs 1.3.6.1.4.1.18.3.4.9.33.1.15
The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtTable 1.3.6.1.4.1.18.3.4.9.34
Current Day statistics Alarm Threshold Crossing table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1DayThrAlrtEntry

wfDs1E1DayThrAlrtEntry 1.3.6.1.4.1.18.3.4.9.34.1
An entry in the DS1E1 ThrAlrt table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1DayThrAlrtEntry  

wfDs1E1DayThrAlrtDelete 1.3.6.1.4.1.18.3.4.9.34.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1DayThrAlrtPortLineNumber 1.3.6.1.4.1.18.3.4.9.34.1.2
The instance ID that identifies the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1DayThrAlrtESs 1.3.6.1.4.1.18.3.4.9.34.1.3
The number of Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtSESs 1.3.6.1.4.1.18.3.4.9.34.1.4
The number of Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtSEFSs 1.3.6.1.4.1.18.3.4.9.34.1.5
The number of Severely Errored Framing Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtUASs 1.3.6.1.4.1.18.3.4.9.34.1.6
The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtCSSs 1.3.6.1.4.1.18.3.4.9.34.1.7
The number of Controlled Slip Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtPCVs 1.3.6.1.4.1.18.3.4.9.34.1.8
The number of Path Coding Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtLESs 1.3.6.1.4.1.18.3.4.9.34.1.9
The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtBESs 1.3.6.1.4.1.18.3.4.9.34.1.10
The number of Bursty Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtDMs 1.3.6.1.4.1.18.3.4.9.34.1.11
The number of Degraded Minutes which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtLCVs 1.3.6.1.4.1.18.3.4.9.34.1.12
The number of Line Code Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtSASs 1.3.6.1.4.1.18.3.4.9.34.1.13
The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtAISSs 1.3.6.1.4.1.18.3.4.9.34.1.14
The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1DayThrAlrtFCs 1.3.6.1.4.1.18.3.4.9.34.1.15
The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtTable 1.3.6.1.4.1.18.3.4.9.35
Current Far End statistics Alarm Threshold Crossing table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndThrAlrtEntry

wfDs1E1FarEndThrAlrtEntry 1.3.6.1.4.1.18.3.4.9.35.1
An entry in the DS1E1 ThrAlrt table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndThrAlrtEntry  

wfDs1E1FarEndThrAlrtDelete 1.3.6.1.4.1.18.3.4.9.35.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1FarEndThrAlrtPortLineNumber 1.3.6.1.4.1.18.3.4.9.35.1.2
The instance ID that identifies the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndThrAlrtESs 1.3.6.1.4.1.18.3.4.9.35.1.3
The number of Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtSESs 1.3.6.1.4.1.18.3.4.9.35.1.4
The number of Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtSEFSs 1.3.6.1.4.1.18.3.4.9.35.1.5
The number of Severely Errored Framing Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtUASs 1.3.6.1.4.1.18.3.4.9.35.1.6
The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtCSSs 1.3.6.1.4.1.18.3.4.9.35.1.7
The number of Controlled Slip Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtPCVs 1.3.6.1.4.1.18.3.4.9.35.1.8
The number of Path Coding Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtLESs 1.3.6.1.4.1.18.3.4.9.35.1.9
The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtBESs 1.3.6.1.4.1.18.3.4.9.35.1.10
The number of Bursty Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtDMs 1.3.6.1.4.1.18.3.4.9.35.1.11
The number of Degraded Minutes which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtLCVs 1.3.6.1.4.1.18.3.4.9.35.1.12
The number of Line Code Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtSASs 1.3.6.1.4.1.18.3.4.9.35.1.13
The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtAISSs 1.3.6.1.4.1.18.3.4.9.35.1.14
The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndThrAlrtFCs 1.3.6.1.4.1.18.3.4.9.35.1.15
The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtTable 1.3.6.1.4.1.18.3.4.9.36
Current Far End Day statistics Alarm Threshold Crossing table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1FarEndDayThrAlrtEntry

wfDs1E1FarEndDayThrAlrtEntry 1.3.6.1.4.1.18.3.4.9.36.1
An entry in the DS1E1 ThrAlrt table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1FarEndDayThrAlrtEntry  

wfDs1E1FarEndDayThrAlrtDelete 1.3.6.1.4.1.18.3.4.9.36.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDs1E1FarEndDayThrAlrtPortLineNumber 1.3.6.1.4.1.18.3.4.9.36.1.2
The instance ID that identifies the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1FarEndDayThrAlrtESs 1.3.6.1.4.1.18.3.4.9.36.1.3
The number of Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtSESs 1.3.6.1.4.1.18.3.4.9.36.1.4
The number of Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtSEFSs 1.3.6.1.4.1.18.3.4.9.36.1.5
The number of Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtUASs 1.3.6.1.4.1.18.3.4.9.36.1.6
The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtCSSs 1.3.6.1.4.1.18.3.4.9.36.1.7
The number of Controlled Slip Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtPCVs 1.3.6.1.4.1.18.3.4.9.36.1.8
The number of Path Coding Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtLESs 1.3.6.1.4.1.18.3.4.9.36.1.9
The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtBESs 1.3.6.1.4.1.18.3.4.9.36.1.10
The number of Bursty Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtDMs 1.3.6.1.4.1.18.3.4.9.36.1.11
The number of Degraded Minutes which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtLCVs 1.3.6.1.4.1.18.3.4.9.36.1.12
The number of Line Code Violations which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtSASs 1.3.6.1.4.1.18.3.4.9.36.1.13
The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtAISSs 1.3.6.1.4.1.18.3.4.9.36.1.14
The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1FarEndDayThrAlrtFCs 1.3.6.1.4.1.18.3.4.9.36.1.15
The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfDs1E1LineQueStatTable 1.3.6.1.4.1.18.3.4.9.20
This file describes the MIBS for getting Line Queue Stats
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1E1LineQueStatEntry

wfDs1E1LineQueStatEntry 1.3.6.1.4.1.18.3.4.9.20.1
An entry in the Queue Base table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1E1LineQueStatEntry  

wfDs1E1LineQueStatPortLineNumber 1.3.6.1.4.1.18.3.4.9.20.1.1
Instance ID PortLineNumber
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineQueStatLineIndex 1.3.6.1.4.1.18.3.4.9.20.1.2
Instance Line Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineQueStatQueueIndex 1.3.6.1.4.1.18.3.4.9.20.1.3
Queue Index, matches that of wfQosServPkgQueCfgQueueIndex or one for best effort.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1E1LineQueStatTxOctets 1.3.6.1.4.1.18.3.4.9.20.1.4
Number of Transmit Octets received by the Queue without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineQueStatTxPackets 1.3.6.1.4.1.18.3.4.9.20.1.5
Number of Transmit Packets received by the Queue without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1E1LineQueStatTxDrops 1.3.6.1.4.1.18.3.4.9.20.1.6
Number of Transmit Packets Dropped by the Queue
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter