Wellfleet-MCT1-MIB

File: Wellfleet-MCT1-MIB.mib (60203 bytes)

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

Counter	Gauge	OBJECT-TYPE
DisplayString	wfMcT1Group

Defined Types

WfMcT1ModEntry
SEQUENCE
	wfMcT1ModDelete	INTEGER
	wfMcT1ModDisable	INTEGER
	wfMcT1ModSlot	INTEGER
	wfMcT1ModPrimaryClock	INTEGER
	wfMcT1ModSecondaryClock	INTEGER
	wfMcT1ModCurrentClock	INTEGER
	wfMcT1ModExtClockOperational	INTEGER
	wfMcT1ModLoop0ClockOperational	INTEGER
	wfMcT1ModLoop1ClockOperational	INTEGER
	wfMcT1ModRestart	INTEGER

WfMcT1Entry
SEQUENCE
	wfMcT1Delete	INTEGER
	wfMcT1Disable	INTEGER
	wfMcT1State	INTEGER
	wfMcT1Slot	INTEGER
	wfMcT1Connector	INTEGER
	wfMcT1OperationMode	INTEGER
	wfMcT1Mtu	INTEGER
	wfMcT1MunichVersion	INTEGER
	wfMcT1Dsx1LineType	INTEGER
	wfMcT1Dsx1ZeroCoding	INTEGER
	wfMcT1Dsx1LoopbackConfig	INTEGER
	wfMcT1Dsx1LineStatus	INTEGER
	wfMcT1Dsx1SetupAlarmThreshold	INTEGER
	wfMcT1Dsx1ClearAlarmThreshold	INTEGER
	wfMcT1Dsx1SignalLevel	INTEGER
	wfMcT1LoopbackDisable	INTEGER
	wfMcT1Dsx1FDLOperationMode	INTEGER
	wfMcT1BertTxOutputLevel	INTEGER
	wfMcT1BertTestMode	INTEGER
	wfMcT1BertLineCode	INTEGER
	wfMcT1BertTestPattern	INTEGER
	wfMcT1BertSendAlarm	INTEGER
	wfMcT1DS2282Version	INTEGER
	wfMcT1Restart	INTEGER
	wfMcT1Loopback	INTEGER
	wfMcT1FDLTargetAddress	INTEGER

WfMcT1ConfigEntry
SEQUENCE
	wfMcT1ConfigSlot	INTEGER
	wfMcT1ConfigConnector	INTEGER
	wfMcT1BertRestart	INTEGER
	wfMcT1BertPayldLb	INTEGER
	wfMcT1BertLineLb	INTEGER
	wfMcT1BertErrorInsert	INTEGER
	wfMcT1Dsx1SendLoopCode	INTEGER
	wfMcT1Dsx1SendFDLCode	INTEGER

WfMcT1LineEntry
SEQUENCE
	wfMcT1LineDelete	INTEGER
	wfMcT1LineDisable	INTEGER
	wfMcT1LineState	INTEGER
	wfMcT1LineSlot	INTEGER
	wfMcT1LineConnector	INTEGER
	wfMcT1LineLine	INTEGER
	wfMcT1LineCct	INTEGER
	wfMcT1LineBofl	INTEGER
	wfMcT1LineBoflTmo	INTEGER
	wfMcT1LineFractionalLpbk	INTEGER
	wfMcT1LineChannelAssignment	DisplayString
	wfMcT1LineMadr	OCTET STRING
	wfMcT1LineWanProtocol	INTEGER
	wfMcT1LineService	INTEGER
	wfMcT1LineRateAdaption	INTEGER
	wfMcT1LineIFTF	INTEGER
	wfMcT1LineCRCSize	INTEGER
	wfMcT1LineRxOctets	Counter
	wfMcT1LineRxFrames	Counter
	wfMcT1LineTxOctets	Counter
	wfMcT1LineTxFrames	Counter
	wfMcT1LineRxErrors	Counter
	wfMcT1LineTxErrors	Counter
	wfMcT1LineLackRxResources	Counter
	wfMcT1LineLackTxResources	Counter
	wfMcT1LineTxUnderflows	Counter
	wfMcT1LineRxOverflows	Counter
	wfMcT1LineRxNullFrames	Counter
	wfMcT1LineRxShortFrames	Counter
	wfMcT1LineRxLossSyncs	Counter
	wfMcT1LineRxCRCErrors	Counter
	wfMcT1LineRxNonOctetBits	Counter
	wfMcT1LineRxLongFrames	Counter
	wfMcT1LineRxAbortFrames	Counter
	wfMcT1LineRxDescOverflows	Counter
	wfMcT1LineTurboBofl	INTEGER
	wfMcT1LineBoflNum	INTEGER
	wfMcT1LineBoflLen	INTEGER
	wfMcT1LineRxIntProcs	Counter
	wfMcT1LineTxIntProcs	Counter
	wfMcT1LineRxPktCorruptions	Counter
	wfMcT1LineRxReplenMisses	Counter
	wfMcT1LineRxIFCs	Counter
	wfMcT1LineCfgTxQueueLength	INTEGER
	wfMcT1LineCfgRxQueueLength	INTEGER
	wfMcT1LineTxQueueLength	INTEGER
	wfMcT1LineRxQueueLength	INTEGER
	wfMcT1LineTxQueueEmpty	INTEGER
	wfMcT1LineMtu	INTEGER
	wfMcT1LineRestart	INTEGER
	wfMcT1LineLineNumber	INTEGER

WfMcT1Dsx1CurrentEntry
SEQUENCE
	wfMcT1Dsx1CurrentSlot	INTEGER
	wfMcT1Dsx1CurrentConnector	INTEGER
	wfMcT1Dsx1CurrentIntervalTimer	Gauge
	wfMcT1Dsx1CurrentESs	Gauge
	wfMcT1Dsx1CurrentSESs	Gauge
	wfMcT1Dsx1CurrentBESs	Gauge
	wfMcT1Dsx1CurrentUASs	Gauge
	wfMcT1Dsx1CurrentCSSs	Gauge
	wfMcT1Dsx1CurrentBPVs	Gauge

WfMcT1Dsx1IntervalEntry
SEQUENCE
	wfMcT1Dsx1IntervalSlot	INTEGER
	wfMcT1Dsx1IntervalConnector	INTEGER
	wfMcT1Dsx1IntervalNumber	INTEGER
	wfMcT1Dsx1IntervalESs	Gauge
	wfMcT1Dsx1IntervalSESs	Gauge
	wfMcT1Dsx1IntervalBESs	Gauge
	wfMcT1Dsx1IntervalUASs	Gauge
	wfMcT1Dsx1IntervalCSSs	Gauge
	wfMcT1Dsx1IntervalBPVs	Gauge

WfMcT1Dsx1TotalEntry
SEQUENCE
	wfMcT1Dsx1TotalSlot	INTEGER
	wfMcT1Dsx1TotalConnector	INTEGER
	wfMcT1Dsx1TotalVITR	Gauge
	wfMcT1Dsx1TotalESs	Gauge
	wfMcT1Dsx1TotalSESs	Gauge
	wfMcT1Dsx1TotalBESs	Gauge
	wfMcT1Dsx1TotalUASs	Gauge
	wfMcT1Dsx1TotalCSSs	Gauge
	wfMcT1Dsx1TotalBPVs	Gauge

WfMcT1AnsiEntry
SEQUENCE
	wfMcT1AnsiSlot	INTEGER
	wfMcT1AnsiConnector	INTEGER
	wfMcT1AnsiCRCCounts	Counter
	wfMcT1AnsiBPVCounts	Counter
	wfMcT1AnsiOOFCounts	Counter
	wfMcT1AnsiFECounts	Counter
	wfMcT1AnsiESCounts	Counter
	wfMcT1AnsiSESCounts	Counter
	wfMcT1AnsiUASCounts	Counter
	wfMcT1AnsiPRMR0Counts	Counter
	wfMcT1AnsiPRMR1Counts	Counter
	wfMcT1AnsiPRMR2Counts	Counter
	wfMcT1AnsiPRMR3Counts	Counter
	wfMcT1AnsiPRMESCounts	Counter
	wfMcT1AnsiPRMSESCounts	Counter
	wfMcT1AnsiPRMECounts	Counter

WfMcT1BertStatsEntry
SEQUENCE
	wfMcT1BertStatsSlot	INTEGER
	wfMcT1BertStatsConnector	INTEGER
	wfMcT1BertStatsBitErrors	Counter
	wfMcT1BertStatsBits	Counter

Defined Values

wfMcT1ModTable		1.3.6.1.4.1.18.3.4.8.1
MCT1 MOD record - Contains MCT1 module Configuration parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1ModEntry

wfMcT1ModEntry		1.3.6.1.4.1.18.3.4.8.1.1
An entry in the MCT1 Base table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1ModEntry

wfMcT1ModDelete		1.3.6.1.4.1.18.3.4.8.1.1.1
Create/Delete parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfMcT1ModDisable		1.3.6.1.4.1.18.3.4.8.1.1.2
Enable/Disable parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1ModSlot		1.3.6.1.4.1.18.3.4.8.1.1.3
Instance ID slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1ModPrimaryClock		1.3.6.1.4.1.18.3.4.8.1.1.4
Specifies the primary source for T1 transmit timing. Both T1 ports use the same T1 transmit timing source. The options for T1 timing source are internal timing source, loop timing from either T1 port and an external timing source.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	external(1), loop0(2), loop1(3), int(4)

wfMcT1ModSecondaryClock		1.3.6.1.4.1.18.3.4.8.1.1.5
Specifies the secondary source for T1 transmit timing. During normal operation T1 transmit timing is derived from the primary timing source. If the primary timing source fails, the software switches to secondary timing source.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	external(1), loop0(2), loop1(3), int(4)

wfMcT1ModCurrentClock		1.3.6.1.4.1.18.3.4.8.1.1.6
Indicates the clock source currently in use
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), secondary(2), int(3)

wfMcT1ModExtClockOperational		1.3.6.1.4.1.18.3.4.8.1.1.7
Indicates whether the External clock is operational
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	oper(1), unoper(2)

wfMcT1ModLoop0ClockOperational		1.3.6.1.4.1.18.3.4.8.1.1.8
Indicates whether the timing source from port 1 is operational
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	oper(1), unoper(2)

wfMcT1ModLoop1ClockOperational		1.3.6.1.4.1.18.3.4.8.1.1.9
Indicates whether the timing source from port 2 is operational
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	oper(1), unoper(2)

wfMcT1ModRestart		1.3.6.1.4.1.18.3.4.8.1.1.10
Indicates Module gate should be restarted to read new configuration
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfMcT1Table		1.3.6.1.4.1.18.3.4.8.2
MCT1 line record - Contains MUNICH32 Configuration parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1Entry

wfMcT1Entry		1.3.6.1.4.1.18.3.4.8.2.1
An entry in the MCT1 table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1Entry

wfMcT1Delete		1.3.6.1.4.1.18.3.4.8.2.1.1
Create/Delete parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfMcT1Disable		1.3.6.1.4.1.18.3.4.8.2.1.2
Enable/Disable parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1State		1.3.6.1.4.1.18.3.4.8.2.1.3
Line Driver state variable
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	init(1), up(2), bert(3), loopback(4), redalarm(5), yelalarm(6), bluealarm(7), notpresent(8)

wfMcT1Slot		1.3.6.1.4.1.18.3.4.8.2.1.4
Instance ID Slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1Connector		1.3.6.1.4.1.18.3.4.8.2.1.5
Instance ID Connector, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1OperationMode		1.3.6.1.4.1.18.3.4.8.2.1.6
An option to generate and analyze specific test patterns is provided in BERT mode of operation. Only one T1 port can be in BERT mode at a time. This attribute selects normal or BERT mode of operation
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	default(1), bert(2)

wfMcT1Mtu		1.3.6.1.4.1.18.3.4.8.2.1.7
MTU parameter. Specifies the largest frame size that can be received by the MCT1 link module. Any received frame which is larger than the MTU will be discarded.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	3..4608

wfMcT1MunichVersion		1.3.6.1.4.1.18.3.4.8.2.1.8
Specifies version number of the MUNICH chip used
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	v1(1), v2(2)

wfMcT1Dsx1LineType		1.3.6.1.4.1.18.3.4.8.2.1.9
Selects between the two framing formats supported - D4 and ESF. The sailent differences between the two formats are the number of frames per superframe and the use of F-bit position.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	esf(2), d4(3)

wfMcT1Dsx1ZeroCoding		1.3.6.1.4.1.18.3.4.8.2.1.10
Selects between the two Zero Code Suppression formats used on the link. In B8ZS coding, any outgoing stream of eight consecutive zeroes is replaced with a B8ZS code word. Any received B8ZS code is replaced with all zeroes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b8zs(2), ami(5)

wfMcT1Dsx1LoopbackConfig		1.3.6.1.4.1.18.3.4.8.2.1.11
Indicates the loopback configuration of the T1 interface. The interface can be in the following loopback states: Payload loopback and Line loopback or no loopback. The loopbacks can be initiated by the manager of this device or by the far end. The loopbacks initiated by the far end are NETREQPAYLOADLOOP and NETREQLINELOOP.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noloop(1), mgrpayloadloop(2), mgrlineloop(3), netreqpayloadloop(4), netreqlineloop(5), otherloop(6)

wfMcT1Dsx1LineStatus		1.3.6.1.4.1.18.3.4.8.2.1.12
Indicates the line status of the T1 interface. It contains loopback state and alarm state information. The Dsx1LineStatus is a bit map therefore it can represent multiple loopback and alarm states simultaneously.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noalarm(1), farendalarm(2), alarmindicationsignal(4), lossofframe(8), lossofsignal(16), loopbackstate(32)

wfMcT1Dsx1SetupAlarmThreshold		1.3.6.1.4.1.18.3.4.8.2.1.13
Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the time specified by this parameter a performance failure is registered and a message is logged.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	threshold2(2), threshold4(4), threshold6(6), threshold8(8), threshold10(10)

wfMcT1Dsx1ClearAlarmThreshold		1.3.6.1.4.1.18.3.4.8.2.1.14
Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for greater than the time specified by this parameter then the failure cleared condition is registered and a message is logged.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	threshold2(2), threshold4(4), threshold6(6), threshold8(8), threshold10(10)

wfMcT1Dsx1SignalLevel		1.3.6.1.4.1.18.3.4.8.2.1.15
Specifies T1 transmit power level, in terms of DB. They translate into cable length as follows: 0.0dB -> 0-133 ft 0.5dB -> 133-266 ft 0.8dB -> 266-399 ft 1.1dB -> 399-533 ft 1.5dB -> 533-655 ft
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	minus15(1), minus7point5(2), minus0(3), pluspoint5(4), pluspoint8(5), plus1point1(6), plus1point5(7)

wfMcT1LoopbackDisable		1.3.6.1.4.1.18.3.4.8.2.1.16
The MCT1 link module is capable of detecting loop up and loop down codes received from the far end. This parameter enables or disbales loop up/down code detection circuitry
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1Dsx1FDLOperationMode		1.3.6.1.4.1.18.3.4.8.2.1.17
Select between the two FDL modes of operation. The AT&T mode, 54016 is based on AT&T publication 54015-1989. The ANSI mode, T1403 is based on ANSI publication T1.403-1989
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	oper54016(1), opert1403(2)

wfMcT1BertTxOutputLevel		1.3.6.1.4.1.18.3.4.8.2.1.18
Specifies T1 transmit power level, in terms of DB while the T1 port is in BERT mode. The power levels translate into cable length as follows: 0.0dB -> 0-133 ft 0.5dB -> 133-266 ft 0.8dB -> 266-399 ft 1.1dB -> 399-533 ft 1.5dB -> 533-655 ft
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	minus15(1), minus7point5(2), minus0(3), pluspoint5(4), pluspoint8(5), plus1point1(6), plus1point5(7)

wfMcT1BertTestMode		1.3.6.1.4.1.18.3.4.8.2.1.19
Selects between the framing formats while in bert mode of operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1(1), sf(2), esf(3)

wfMcT1BertLineCode		1.3.6.1.4.1.18.3.4.8.2.1.20
Selects between the two Zero Code Suppression formats used on the link while in BERT mode. In B8ZS coding, any outgoing stream of eight consecutive zeroes is replaced with a B8ZS code word. Any received B8ZS code is replaced with all zeroes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ami(1), b8zs(2)

wfMcT1BertTestPattern		1.3.6.1.4.1.18.3.4.8.2.1.21
When a T1 port is in BERT mode, it is capable of generating a set of known patterns. This paramater selects between those patterns
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	zeros(1), ones(2), qrss(3), fifteen(4), fifteeninv(5), twenty(6), twentythree(7), twentythreeinv(8)

wfMcT1BertSendAlarm		1.3.6.1.4.1.18.3.4.8.2.1.22
Specifies a blue or yellow alarm to be transmitted while in BERT mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	blue(1), yellow(2), disabled(3)

wfMcT1DS2282Version		1.3.6.1.4.1.18.3.4.8.2.1.23
Specifies version number of DS2282 chip
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfMcT1Restart		1.3.6.1.4.1.18.3.4.8.2.1.24
Indicates Port gate should be restarted to read new configuration
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfMcT1Loopback		1.3.6.1.4.1.18.3.4.8.2.1.25
Selects line or payload loopback to be activated locally
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	linelb(1), payldlb(2), deactivate(3)

wfMcT1FDLTargetAddress		1.3.6.1.4.1.18.3.4.8.2.1.26
Selects between the two FDL target address modes
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	az(1), by(2)

wfMcT1ConfigTable		1.3.6.1.4.1.18.3.4.8.3
MCT1 configuration record - Contains MUNICH32 and Framer write only Configuration parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1ConfigEntry

wfMcT1ConfigEntry		1.3.6.1.4.1.18.3.4.8.3.1
An entry in the MCT1 Config table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1ConfigEntry

wfMcT1ConfigSlot		1.3.6.1.4.1.18.3.4.8.3.1.1
Instance ID Slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1ConfigConnector		1.3.6.1.4.1.18.3.4.8.3.1.2
Instance ID Connector, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1BertRestart		1.3.6.1.4.1.18.3.4.8.3.1.3
Reset counters on BERT device
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), noaction(10)

wfMcT1BertPayldLb		1.3.6.1.4.1.18.3.4.8.3.1.4
Selects a payload loopback code to be sent to the far end by the FDL while in BERT mode. It can be a payload loopback activate or deactivate code.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	act(1), deact(2), noaction(10)

wfMcT1BertLineLb		1.3.6.1.4.1.18.3.4.8.3.1.5
Selects a line loopback code to be sent to the far end while in BERT mode. It can be a line loopback activate or deactivate code using the hardware on the MCT1 board or it can be a code sent by the FDL.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lpup(1), lpdn(2), fdlact(3), fdldeact(4), noaction(10)

wfMcT1BertErrorInsert		1.3.6.1.4.1.18.3.4.8.3.1.6
Indicates that an error be injected into the transmitted data stream while in BERT mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	config(1), thousandconfig(2), millionconfig(3), disable(4), noaction(10)

wfMcT1Dsx1SendLoopCode		1.3.6.1.4.1.18.3.4.8.3.1.7
Selects a Loop Up/Down code to be sent to the remote end
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	loopup(1), loopdn(2), noaction(10)

wfMcT1Dsx1SendFDLCode		1.3.6.1.4.1.18.3.4.8.3.1.8
Selects an FDL code to be sent to the remote end
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ci(1), univlbdeact(2), ia(3), linelbdeact(4), pyldlbact(5), pyldlbdeact(6), ib(7), noaction(10)

wfMcT1LineTable		1.3.6.1.4.1.18.3.4.8.4
MCT1 Channel record - Contains configuration parameters and statistics for MUNICH32 which are channel specific.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1LineEntry

wfMcT1LineEntry		1.3.6.1.4.1.18.3.4.8.4.1
An entry in the MCT1CHANNEL table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1LineEntry

wfMcT1LineDelete		1.3.6.1.4.1.18.3.4.8.4.1.1
Create/Delete parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfMcT1LineDisable		1.3.6.1.4.1.18.3.4.8.4.1.2
Enable/Disable parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1LineState		1.3.6.1.4.1.18.3.4.8.4.1.3
Line Driver state variable
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), loopback(4), wait(5), channel(6), stop(7), notpresent(8)

wfMcT1LineSlot		1.3.6.1.4.1.18.3.4.8.4.1.4
Instance ID Slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1LineConnector		1.3.6.1.4.1.18.3.4.8.4.1.5
Instance ID Connector, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1LineLine		1.3.6.1.4.1.18.3.4.8.4.1.6
Line number for this line instance, filled in by driver. The line number corresponds to the position of the circuit, from 1 to 24, on the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..24

wfMcT1LineCct		1.3.6.1.4.1.18.3.4.8.4.1.7
Circuit number for this line instance
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1023

wfMcT1LineBofl		1.3.6.1.4.1.18.3.4.8.4.1.8
Selects Breath of Life (BOFL) parameter. If selected, a BOFL packet is sent out on the wire as often as specifies by the wfMcT1LineBoflTmo parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1LineBoflTmo		1.3.6.1.4.1.18.3.4.8.4.1.9
Indicates the time-period between BOFL packets
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..60

wfMcT1LineFractionalLpbk		1.3.6.1.4.1.18.3.4.8.4.1.10
Any circuit on this T1 port is capable of being put into loopback, i.e. data coming into that circuit from the wire is mirrorred back onto the wire. This parameter enables or disables this loopback feature on any circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1LineChannelAssignment		1.3.6.1.4.1.18.3.4.8.4.1.11
Lists the time-slots which constitute this channel. User types in a list of time-slots from 1 to 24 separated by commas
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfMcT1LineMadr		1.3.6.1.4.1.18.3.4.8.4.1.12
Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfMcT1LineWanProtocol		1.3.6.1.4.1.18.3.4.8.4.1.13
WAN protocol selection is provided via this parameter. The supported protocols can be selected per circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), ppp(2), smds(3), framerelay(4), switch(5), sw(6)

wfMcT1LineService		1.3.6.1.4.1.18.3.4.8.4.1.14
Service type for this circuit. Supports raw HDLC mode. Does not support LLC1 at this time. LLC1 mode will prefix the HDLC address and control fields to the frame. May support LLC1 mode in the future
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	hdlc(1), llc1(2)

wfMcT1LineRateAdaption		1.3.6.1.4.1.18.3.4.8.4.1.15
Determines the number of bits and their bit positions within the time-slot. 64k selection uses all 8 bits in the time-slot. The two 56k selections use 7 of the 8 bits in the time-slot. 56k_MSB does not use the most significant bit and 56k_LSB does not use the least significant bit in the time-slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	adaption64k(1), msb(2), lsb(3)

wfMcT1LineIFTF		1.3.6.1.4.1.18.3.4.8.4.1.16
Determines the Interframe time fill character to be transmitted by the MUNICH. In case of IFTF_FLAGS, 0x7E is sent and in case of IFTF_IDLES 0xff is sent as the interframe timefill characters.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	flags(1), idles(2)

wfMcT1LineCRCSize		1.3.6.1.4.1.18.3.4.8.4.1.17
Determines the CRC Size. When CRC32 is selected a 32 bit CRC is appended to the frame being transmitted and a 32 bit CRC check is performed on the received frame. When CRC16 is selected, a 16 bit CRC is appended to the transmitted frame and a 16 bit CRC is performed. on the received frame.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	crc32(1), crc16(2)

wfMcT1LineRxOctets		1.3.6.1.4.1.18.3.4.8.4.1.18
Number of octets received without error
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxFrames		1.3.6.1.4.1.18.3.4.8.4.1.19
Number of frames received without error
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTxOctets		1.3.6.1.4.1.18.3.4.8.4.1.20
Number of octets transmitted without error
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTxFrames		1.3.6.1.4.1.18.3.4.8.4.1.21
Number of frames transmitted without error
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxErrors		1.3.6.1.4.1.18.3.4.8.4.1.22
Number of receive errors
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTxErrors		1.3.6.1.4.1.18.3.4.8.4.1.23
Number of transmission errors
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineLackRxResources		1.3.6.1.4.1.18.3.4.8.4.1.24
Number of Rx frames dropped due to lack of buffer resources
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineLackTxResources		1.3.6.1.4.1.18.3.4.8.4.1.25
Number of Tx frames dropped due to lack of buffer resources
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTxUnderflows		1.3.6.1.4.1.18.3.4.8.4.1.26
Number of Tx frames dropped due to Transmit underflow
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxOverflows		1.3.6.1.4.1.18.3.4.8.4.1.27
Number of Rx frames dropped due to Receive overflow
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxNullFrames		1.3.6.1.4.1.18.3.4.8.4.1.28
Number of short frames received (with no data bytes)
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxShortFrames		1.3.6.1.4.1.18.3.4.8.4.1.29
Number of short frames received (less than or equal to two data bytes)
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxLossSyncs		1.3.6.1.4.1.18.3.4.8.4.1.30
Loss of synchronization on receiver
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxCRCErrors		1.3.6.1.4.1.18.3.4.8.4.1.31
CRC error received
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxNonOctetBits		1.3.6.1.4.1.18.3.4.8.4.1.32
Non-Octet bits received in frame
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxLongFrames		1.3.6.1.4.1.18.3.4.8.4.1.33
Frame longer than MFL received
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxAbortFrames		1.3.6.1.4.1.18.3.4.8.4.1.34
Aborted frame received
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxDescOverflows		1.3.6.1.4.1.18.3.4.8.4.1.35
Receive overflow on chip buffer
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTurboBofl		1.3.6.1.4.1.18.3.4.8.4.1.36
DEBUG parameter - Turbo bofl enabled or disabled
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfMcT1LineBoflNum		1.3.6.1.4.1.18.3.4.8.4.1.37
DEBUG parameter - Number of breath of life packets per breath of life
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..127

wfMcT1LineBoflLen		1.3.6.1.4.1.18.3.4.8.4.1.38
DEBUG parameter - breath of life packet length
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	22..4450

wfMcT1LineRxIntProcs		1.3.6.1.4.1.18.3.4.8.4.1.39
Receive Interrupt processing count
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineTxIntProcs		1.3.6.1.4.1.18.3.4.8.4.1.40
Tx interrupt processing count
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxPktCorruptions		1.3.6.1.4.1.18.3.4.8.4.1.41
Corruption check on receive
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxReplenMisses		1.3.6.1.4.1.18.3.4.8.4.1.42
Count of number of packet buffer misses while attempting to replenish driver receive ring
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineRxIFCs		1.3.6.1.4.1.18.3.4.8.4.1.43
Number of times the device changes its interframe time-fill
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1LineCfgTxQueueLength		1.3.6.1.4.1.18.3.4.8.4.1.44
Configured transmit queue length
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..336

wfMcT1LineCfgRxQueueLength		1.3.6.1.4.1.18.3.4.8.4.1.45
Configured receive queue length
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..336

wfMcT1LineTxQueueLength		1.3.6.1.4.1.18.3.4.8.4.1.46
Current transmit queue length
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfMcT1LineRxQueueLength		1.3.6.1.4.1.18.3.4.8.4.1.47
Current Receive queue length
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfMcT1LineTxQueueEmpty		1.3.6.1.4.1.18.3.4.8.4.1.48
The number of times the transmit ring is found empty when transmitting packets
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfMcT1LineMtu		1.3.6.1.4.1.18.3.4.8.4.1.49
MTU read-only parameter. Specifies the largest frame size that can be received by the MCT1 link module. Any received frame which is larger than the MTU will be discarded. Can be set in MCT1Entry TABLE by the user
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfMcT1LineRestart		1.3.6.1.4.1.18.3.4.8.4.1.50
Indicates channel gate should be restarted to read new configuration
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfMcT1LineLineNumber		1.3.6.1.4.1.18.3.4.8.4.1.51
line number for this line instance
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfMcT1Dsx1CurrentTable		1.3.6.1.4.1.18.3.4.8.5
The MCT1_DSX1 Current table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1Dsx1CurrentEntry

wfMcT1Dsx1CurrentEntry		1.3.6.1.4.1.18.3.4.8.5.1
per circuit MCT1_DSX1 current objects - wfMcT1Dsx1CurrentIndex corresponds to Wellfleet circuit number
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1Dsx1CurrentEntry

wfMcT1Dsx1CurrentSlot		1.3.6.1.4.1.18.3.4.8.5.1.1
this corresponds to the Wellfleet Slot number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1Dsx1CurrentConnector		1.3.6.1.4.1.18.3.4.8.5.1.2
this corresponds to the Wellfleet Connector number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1Dsx1CurrentIntervalTimer		1.3.6.1.4.1.18.3.4.8.5.1.3
the number of seconds in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentESs		1.3.6.1.4.1.18.3.4.8.5.1.4
the number of errored seconds encountered by a DS1 interface in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentSESs		1.3.6.1.4.1.18.3.4.8.5.1.5
the number of severely errored seconds in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentBESs		1.3.6.1.4.1.18.3.4.8.5.1.6
the number of bursty errored seconds in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentUASs		1.3.6.1.4.1.18.3.4.8.5.1.7
the number of unavailable seconds in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentCSSs		1.3.6.1.4.1.18.3.4.8.5.1.8
the number of Controlled Slip seconds in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1CurrentBPVs		1.3.6.1.4.1.18.3.4.8.5.1.9
the number of bipolar violations in the current 15 minute interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalTable		1.3.6.1.4.1.18.3.4.8.6
The MCT1_DSX1 Interval table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1Dsx1IntervalEntry

wfMcT1Dsx1IntervalEntry		1.3.6.1.4.1.18.3.4.8.6.1
per circuit MCT1_DSX1 interval objects - wfMcT1Dsx1IntervalIndex corresponds to Wellfleet circuit number, wfMcT1Dsx1IntervalNumber is the numbered previous 15-minute interval
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1Dsx1IntervalEntry

wfMcT1Dsx1IntervalSlot		1.3.6.1.4.1.18.3.4.8.6.1.1
this corresponds to the Wellfleet Slot number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1Dsx1IntervalConnector		1.3.6.1.4.1.18.3.4.8.6.1.2
this corresponds to the Wellfleet Connector number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1Dsx1IntervalNumber		1.3.6.1.4.1.18.3.4.8.6.1.3
1..96 where 1 is the most recent 15-minute interval and 96 is the least
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..96

wfMcT1Dsx1IntervalESs		1.3.6.1.4.1.18.3.4.8.6.1.4
the number of errored seconds in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalSESs		1.3.6.1.4.1.18.3.4.8.6.1.5
the number of severely errored seconds in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalBESs		1.3.6.1.4.1.18.3.4.8.6.1.6
the number of bursty errored seconds in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalUASs		1.3.6.1.4.1.18.3.4.8.6.1.7
the number of unavailable seconds in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalCSSs		1.3.6.1.4.1.18.3.4.8.6.1.8
the number of controlled slip seconds in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1IntervalBPVs		1.3.6.1.4.1.18.3.4.8.6.1.9
the number of bipolar violations in the specified interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalTable		1.3.6.1.4.1.18.3.4.8.7
The MCT1_DSX1 Total table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1Dsx1TotalEntry

wfMcT1Dsx1TotalEntry		1.3.6.1.4.1.18.3.4.8.7.1
per circuit MCT1_DSX1 total objects - wfMcT1Dsx1TotalIndex corresponds to Wellfleet circuit number
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1Dsx1TotalEntry

wfMcT1Dsx1TotalSlot		1.3.6.1.4.1.18.3.4.8.7.1.1
this corresponds to the Wellfleet Slot number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1Dsx1TotalConnector		1.3.6.1.4.1.18.3.4.8.7.1.2
this corresponds to the Wellfleet Connector number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1Dsx1TotalVITR		1.3.6.1.4.1.18.3.4.8.7.1.3
Indicates the number of valid 15 minute intervals in the previous 24 hour period
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalESs		1.3.6.1.4.1.18.3.4.8.7.1.4
The number of errored seconds encountered by the DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalSESs		1.3.6.1.4.1.18.3.4.8.7.1.5
The number of severely errored seconds encountered by a DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalBESs		1.3.6.1.4.1.18.3.4.8.7.1.6
The number of bursty errored seconds encountered by a DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalUASs		1.3.6.1.4.1.18.3.4.8.7.1.7
The number of unavailable seconds encountered by by a DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalCSSs		1.3.6.1.4.1.18.3.4.8.7.1.8
The number of controlled slip seconds encountered by a DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1Dsx1TotalBPVs		1.3.6.1.4.1.18.3.4.8.7.1.9
The number of bipolar violations encountered by a DS1 interface in the previous 24 hour interval
Status: mandatory	Access: read-only
OBJECT-TYPE
	Gauge

wfMcT1AnsiTable		1.3.6.1.4.1.18.3.4.8.8
ANSI Statistics line record - This table contains the performance parameters for the ANSI register set
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1AnsiEntry

wfMcT1AnsiEntry		1.3.6.1.4.1.18.3.4.8.8.1
An entry in the MCT1 Ansi table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1AnsiEntry

wfMcT1AnsiSlot		1.3.6.1.4.1.18.3.4.8.8.1.1
Instance ID Slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1AnsiConnector		1.3.6.1.4.1.18.3.4.8.8.1.2
Instance ID Connector, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1AnsiCRCCounts		1.3.6.1.4.1.18.3.4.8.8.1.3
Counts CRC-6 error events
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiBPVCounts		1.3.6.1.4.1.18.3.4.8.8.1.4
Counts bipolar violations
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiOOFCounts		1.3.6.1.4.1.18.3.4.8.8.1.5
Counts out-of-frame error events
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiFECounts		1.3.6.1.4.1.18.3.4.8.8.1.6
Counts errors in the FPS framing pattern
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiESCounts		1.3.6.1.4.1.18.3.4.8.8.1.7
Counts errorred seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiSESCounts		1.3.6.1.4.1.18.3.4.8.8.1.8
Counts severly errorred seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiUASCounts		1.3.6.1.4.1.18.3.4.8.8.1.9
counts unavailable seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMR0Counts		1.3.6.1.4.1.18.3.4.8.8.1.10
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMR1Counts		1.3.6.1.4.1.18.3.4.8.8.1.11
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMR2Counts		1.3.6.1.4.1.18.3.4.8.8.1.12
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMR3Counts		1.3.6.1.4.1.18.3.4.8.8.1.13
Counts PRMs that ewre received in the FDL in the last four seconds
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMESCounts		1.3.6.1.4.1.18.3.4.8.8.1.14
Counts errorred seconds as reported in the Performance report messages
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMSESCounts		1.3.6.1.4.1.18.3.4.8.8.1.15
Counts severely errorred seconds as reported in the Performance report messages
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1AnsiPRMECounts		1.3.6.1.4.1.18.3.4.8.8.1.16
Counts Performance report messages that are received in error
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1BertStatsTable		1.3.6.1.4.1.18.3.4.8.9
BERT Counter line record - This table contains the statistics for the BERT tester.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfMcT1BertStatsEntry

wfMcT1BertStatsEntry		1.3.6.1.4.1.18.3.4.8.9.1
An entry in the MCT1 Bert Stats table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfMcT1BertStatsEntry

wfMcT1BertStatsSlot		1.3.6.1.4.1.18.3.4.8.9.1.1
Instance ID Slot, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..14

wfMcT1BertStatsConnector		1.3.6.1.4.1.18.3.4.8.9.1.2
Instance ID Connector, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	one(1), two(2)

wfMcT1BertStatsBitErrors		1.3.6.1.4.1.18.3.4.8.9.1.3
Bit error counter
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfMcT1BertStatsBits		1.3.6.1.4.1.18.3.4.8.9.1.4
Bit counter
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter