XEROX-PRINTER-EXT-MIB

File: XEROX-PRINTER-EXT-MIB.mib (102646 bytes)

Imported modules

RFC1213-MIB SNMPv2-SMI SNMPv2-TC
SNMPv2-CONF HOST-RESOURCES-MIB Printer-MIB
XEROX-COMMON-MIB XEROX-GENERAL-TC XEROX-PRINTER-EXT-TC

Imported symbols

DisplayString MODULE-IDENTITY OBJECT-TYPE
Integer32 RowStatus MODULE-COMPLIANCE
OBJECT-GROUP hrDeviceIndex PresentOnOff
prtGeneralEntry prtInputEntry prtOutputEntry
prtChannelEntry prtInterpreterEntry prtInterpreterIndex
xeroxCommonMIB Cardinal32 Ordinal32
XcmFixedLocaleDisplayString XcmGenRowPersistence XcmPrtAuxSheetContent
XcmPrtAuxSheetType XcmPrtGroupSupport XcmPrtIETFPrintMIBGroupSupport
XcmPrtMediaTypeErrorPolicy XcmPrtMediumClassType XcmPrtMediumSize
XcmPrtOutputOffsetStackingType XcmPrtPageSizeErrorPolicy XcmPrtPCLFontSource
XcmPrtPlex XcmPrtPrintQuality XcmPrtPrintScreen
XcmPrtTraySwitch

Defined Types

XcmPrtBaseEntry  
SEQUENCE    
  xcmPrtBaseIndex Ordinal32
  xcmPrtBaseRowStatus RowStatus
  xcmPrtBaseGroupSupport XcmPrtGroupSupport
  xcmPrtBaseUpdateSupport XcmPrtGroupSupport
  xcmPrtBaseCreateSupport XcmPrtGroupSupport
  xcmPrtBaseIETFMIBGroupSupport XcmPrtIETFPrintMIBGroupSupport
  xcmPrtBaseIETFMIBUpdateSupport XcmPrtIETFPrintMIBGroupSupport
  xcmPrtBaseIETFMIBCreateSupport XcmPrtIETFPrintMIBGroupSupport

XcmPrtGeneralEntry  
SEQUENCE    
  xcmPrtGeneralRowStatus RowStatus
  xcmPrtGeneralAuxSheetPackage Cardinal32
  xcmPrtGeneralManualFeedTimeout Integer32
  xcmPrtGeneralInputAutoSwitch PresentOnOff
  xcmPrtGeneralOutputAutoSwitch PresentOnOff
  xcmPrtGeneralMediumClassDefault XcmPrtMediumClassType
  xcmPrtGeneralDarknessLevels Cardinal32
  xcmPrtGeneralDarknessLevelNorm Cardinal32
  xcmPrtGeneralDarknessLevelDflt Integer32
  xcmPrtGeneralHexDumpEnable PresentOnOff
  xcmPrtGeneralStartupPage PresentOnOff
  xcmPrtGeneralBannerPage PresentOnOff
  xcmPrtGeneralScanlineCompaction PresentOnOff

XcmPrtInputEntry  
SEQUENCE    
  xcmPrtInputRowStatus RowStatus
  xcmPrtInputNextPrtInputIndex Integer32

XcmPrtOutputEntry  
SEQUENCE    
  xcmPrtOutputRowStatus RowStatus
  xcmPrtOutputNextIndex Integer32
  xcmPrtOutputPassword OCTET STRING Size(0..255)
  xcmPrtOutputOffsetStackingType XcmPrtOutputOffsetStackingType
  xcmPrtOutputTrayTimeoutSupport PresentOnOff
  xcmPrtOutputTrayTimeout Cardinal32

XcmPrtChannelEntry  
SEQUENCE    
  xcmPrtChannelRowStatus RowStatus
  xcmPrtChannelEOJTimeout Cardinal32
  xcmPrtChannelAuxSheetPackage Cardinal32
  xcmPrtChannelSpoolingEnable PresentOnOff
  xcmPrtChannelLangSensing PresentOnOff
  xcmPrtChannelAutoJobEnd PresentOnOff

XcmPrtInterpreterEntry  
SEQUENCE    
  xcmPrtInterpRowStatus RowStatus
  xcmPrtInterpAuxSheetPackage Cardinal32
  xcmPrtInterpContextSaving PresentOnOff
  xcmPrtInterpEdgeEnhancement PresentOnOff
  xcmPrtInterpFontIndexDefault Integer32
  xcmPrtInterpGrayLevels Cardinal32
  xcmPrtInterpGrayLevelDefault Cardinal32
  xcmPrtInterpJamRecovery PresentOnOff
  xcmPrtInterpJobCopiesDefault Ordinal32
  xcmPrtInterpLineWrap PresentOnOff
  xcmPrtInterpMediumSizeDefault XcmPrtMediumSize
  xcmPrtInterpPageProtect PresentOnOff
  xcmPrtInterpPageProtectSize XcmPrtMediumSize
  xcmPrtInterpPageSizeErrorPolicy XcmPrtPageSizeErrorPolicy
  xcmPrtInterpPlexSupported XcmPrtPlex
  xcmPrtInterpPlexDefault XcmPrtPlex
  xcmPrtInterpPrintEdgeToEdge PresentOnOff
  xcmPrtInterpPrintQuality XcmPrtPrintQuality
  xcmPrtInterpPrtInputIndexDflt Cardinal32
  xcmPrtInterpPrtOutputIndexDflt Cardinal32
  xcmPrtInterpResFeedDirDefault Cardinal32
  xcmPrtInterpResXFeedDirDefault Cardinal32
  xcmPrtInterpResIPResIndex Cardinal32
  xcmPrtInterpResIPResIndexDflt Cardinal32
  xcmPrtInterpTextFormLength Cardinal32
  xcmPrtInterpTimeoutJob Cardinal32
  xcmPrtInterpTimeoutPage Cardinal32
  xcmPrtInterpInputAliasIndexDflt Cardinal32
  xcmPrtInterpTraySwitch XcmPrtTraySwitch
  xcmPrtInterpMediumTypeDefault XcmFixedLocaleDisplayString Size(0..255)
  xcmPrtInterpMediaTypeErrPolicy XcmPrtMediaTypeErrorPolicy
  xcmPrtInterpErrorPolicyTimeout Cardinal32
  xcmPrtInterpLineTerm PresentOnOff
  xcmPrtInterpAutoContinue PresentOnOff
  xcmPrtInterpEnvFeederSize XcmPrtMediumSize
  xcmPrtInterpManualFeedPgSize XcmPrtMediumSize
  xcmPrtInterpOffsetStackingType XcmPrtOutputOffsetStackingType

XcmPrtInputAliasEntry  
SEQUENCE    
  xcmPrtInputAliasIndex Cardinal32
  xcmPrtInputAliasRowStatus RowStatus
  xcmPrtInputAliasName XcmFixedLocaleDisplayString Size(0..63)
  xcmPrtInputAliasSwitchProgram DisplayString Size(0..255)

XcmPrtInterpPCLEntry  
SEQUENCE    
  xcmPrtInterpPCLRowStatus RowStatus
  xcmPrtInterpPCLFontSourceDflt XcmPrtPCLFontSource
  xcmPrtInterpPCLFontNumberDflt Cardinal32
  xcmPrtInterpPCLPitchNumerator Cardinal32
  xcmPrtInterpPCLPitchDenominator Cardinal32
  xcmPrtInterpPCLPtSizeNumerator Cardinal32
  xcmPrtInterpPCLPtSizeDenominatr Cardinal32
  xcmPrtInterpPCLPrintScreen XcmPrtPrintScreen

XcmPrtAuxPackageEntry  
SEQUENCE    
  xcmPrtAuxPackageIndex Cardinal32
  xcmPrtAuxPackageRowStatus RowStatus
  xcmPrtAuxPackageType XcmPrtAuxSheetType
  xcmPrtAuxPackageContent XcmPrtAuxSheetContent
  xcmPrtAuxPackagePrtInputIndex Cardinal32
  xcmPrtAuxPackageNext Cardinal32

XcmPrtMedmTypeSupEntry  
SEQUENCE    
  xcmPrtMedmTypeSupIndex Ordinal32
  xcmPrtMedmTypeSupRowStatus RowStatus
  xcmPrtMedmTypeSupRowPersistence XcmGenRowPersistence
  xcmPrtMedmTypeSupName XcmFixedLocaleDisplayString Size(0..255)

Defined Values

xcmPrintMIB 1.3.6.1.4.1.253.8.55
Version: 2.36.pub Xerox Printer MIB Extensions Module. This Module provides extension to the IETF Printer MIB. Copyright (C) 1997 Xerox Corporation. All Rights Reserved.
MODULE-IDENTITY    

xcmPrtBase 1.3.6.1.4.1.253.8.55.1
OBJECT IDENTIFIER    

xcmPrtGeneral 1.3.6.1.4.1.253.8.55.5
OBJECT IDENTIFIER    

xcmPrtInput 1.3.6.1.4.1.253.8.55.8
OBJECT IDENTIFIER    

xcmPrtOutput 1.3.6.1.4.1.253.8.55.9
OBJECT IDENTIFIER    

xcmPrtChannel 1.3.6.1.4.1.253.8.55.14
OBJECT IDENTIFIER    

xcmPrtInterpreter 1.3.6.1.4.1.253.8.55.15
OBJECT IDENTIFIER    

xcmPrtInputAlias 1.3.6.1.4.1.253.8.55.50
OBJECT IDENTIFIER    

xcmPrtAuxSheet 1.3.6.1.4.1.253.8.55.52
OBJECT IDENTIFIER    

xcmPrtAuxPackage 1.3.6.1.4.1.253.8.55.60
OBJECT IDENTIFIER    

xcmPrtMediumTypeSupported 1.3.6.1.4.1.253.8.55.75
OBJECT IDENTIFIER    

xcmPrtInterpPCL 1.3.6.1.4.1.253.8.55.70
OBJECT IDENTIFIER    

xcmPrtBaseTable 1.3.6.1.4.1.253.8.55.1.2
A table of general counters and information for ease of use of the XCMI Printer MIB Extensions Module and the IETF Printer MIB (RFC 1759) on this host system. Usage: The ONLY valid row in the 'xcmPrtBaseTable' shall ALWAYS have an 'xcmPrtBaseIndex' of one ('1').
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtBaseEntry

xcmPrtBaseEntry 1.3.6.1.4.1.253.8.55.1.2.1
An entry of general counters and information for ease of use of the XCMI Printer MIB Extensions Module and the IETF Printer MIB (RFC 1759) on this host system. Usage: The ONLY valid row in the 'xcmPrtBaseTable' shall ALWAYS have an 'xcmPrtBaseIndex' of one ('1').
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtBaseEntry  

xcmPrtBaseIndex 1.3.6.1.4.1.253.8.55.1.2.1.1
A unique value used by this host system to identify this conceptual row in the 'xcmPrtBaseTable'. Usage: The ONLY valid row in the 'xcmPrtBaseTable' shall ALWAYS have an 'xcmPrtBaseIndex' of one ('1').
Status: current Access: not-accessible
OBJECT-TYPE    
  Ordinal32  

xcmPrtBaseRowStatus 1.3.6.1.4.1.253.8.55.1.2.1.2
This object is used to display status of the ONLY valid conceptual row in the 'xcmPrtBaseTable'. Usage: 'xcmPrtBaseRowStatus' is 'read-only' because the ONLY valid conceptual row shall NOT be deleted.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

xcmPrtBaseGroupSupport 1.3.6.1.4.1.253.8.55.1.2.1.3
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects which are supported by this management agent implementation (ie, version) on this host system, specified in a bit-mask.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtGroupSupport  

xcmPrtBaseUpdateSupport 1.3.6.1.4.1.253.8.55.1.2.1.4
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects which are supported for existing row update (via SNMP Set-Request PDUs) by this management agent implementation (ie, version) on this host system, specified in a bit-mask.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtGroupSupport  

xcmPrtBaseCreateSupport 1.3.6.1.4.1.253.8.55.1.2.1.5
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects which are supported for dynamic row creation (via '...RowStatus') by this management agent implementation (ie, version) on this host system, specified in a bit-mask.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtGroupSupport  

xcmPrtBaseIETFMIBGroupSupport 1.3.6.1.4.1.253.8.55.1.2.1.6
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects in the IETF Printer MIB which are supported by this management agent implementation (ie, version) on this host system, specified in a bit-mask.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtIETFPrintMIBGroupSupport  

xcmPrtBaseIETFMIBUpdateSupport 1.3.6.1.4.1.253.8.55.1.2.1.7
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects in the IETF Printer MIB supported for existing row update (via SNMP Set-Request PDUs) by this management agent implementation (ie, version) on this host system, specified in a bit-mask.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtIETFPrintMIBGroupSupport  

xcmPrtBaseIETFMIBCreateSupport 1.3.6.1.4.1.253.8.55.1.2.1.8
The terse conformance statement of ALL mandatory, conditionally mandatory, and optional module objects in the IETF Printer MIB supported for dynamic row creation (via '...RowStatus') by this management agent implementation (ie, version) on this host system, specified in a bit-mask. Currently there are no groups within the IETF Printer MIB which provide for dynamic row creation, and this object shall always return '0'. Dynamic row creation is provided to these groups through the XCMI Printer MIB Extensions Module, but CreateSupport should be reflected in xcmPrtBaseCreateSupport. This object is included for completeness.
Status: current Access: read-only
OBJECT-TYPE    
  XcmPrtIETFPrintMIBGroupSupport  

xcmPrtGeneralTable 1.3.6.1.4.1.253.8.55.5.1
A table of general information per printer. This table augments the prtGeneralTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtGeneralEntry

xcmPrtGeneralEntry 1.3.6.1.4.1.253.8.55.5.1.1
An entry exists in this table for each device entry in the hostmib device table whose type is printer.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtGeneralEntry  

xcmPrtGeneralRowStatus 1.3.6.1.4.1.253.8.55.5.1.1.1
Manages the status of this conceptual row in the xcmPrtGeneralTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtGeneralAuxSheetPackage 1.3.6.1.4.1.253.8.55.5.1.1.2
This object is an index into the xcmPrtAuxPackageTable. This table is used to enable or disable printing of auxiliary sheets at the printer box level. The value zero shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtGeneralManualFeedTimeout 1.3.6.1.4.1.253.8.55.5.1.1.3
The duration in seconds after which the printer shall either: (a) switch to another input subunit, if the value of prtInputNextIndex is non-zero and prtGeneralAutoSwitch is on or (b) abort any job waiting for manually fed input, if the value value of prtInputNextIndex is zero or prtGeneralAutoSwitch is off or notPresent. The event which causes the printer to enter the waiting state is product specific. A value of (-1) implies 'other' or 'infinite' which translates to 'this input subunit doesn't support manual feed'. A value of (-2) implies 'unknown'.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xcmPrtGeneralInputAutoSwitch 1.3.6.1.4.1.253.8.55.5.1.1.4
Indicates the state of the auto input switching feature. The value notPresent indicates the feature is not currently supported. Exact behavior of this feature is product specific.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtGeneralOutputAutoSwitch 1.3.6.1.4.1.253.8.55.5.1.1.5
Indicates the state of the auto output tray switching feature. The value notPresent indicates the feature is not currently supported. Exact behavior of this feature is product specific.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtGeneralMediumClassDefault 1.3.6.1.4.1.253.8.55.5.1.1.6
This object sets the default medium size class for the printer. This object sets the medium size for printer management functions such as printing the configuration sheet. It may affect any media related object, such as form length.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediumClassType  

xcmPrtGeneralDarknessLevels 1.3.6.1.4.1.253.8.55.5.1.1.7
This value indicates the maximum number of darkness levels supported by this printer. The level settings range from 1 to xcmPrtGeneralDarknessLevels where 1 represents the lightest level and xcmPrtGeneralDarknessLevels represents the darkest level. The value 1 implies no user settables. The value 0 means unspecified. The selection of a darkness levels specifies that the printer shall process the page images so that they appear either 'lighter' or 'darker'.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtGeneralDarknessLevelNorm 1.3.6.1.4.1.253.8.55.5.1.1.8
The normal setting for the darkness printing object. The value 0 means unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtGeneralDarknessLevelDflt 1.3.6.1.4.1.253.8.55.5.1.1.9
The default setting for the density printing option. The value (-2) indicates unknown. The value (-4) indicates the auto setting.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xcmPrtGeneralHexDumpEnable 1.3.6.1.4.1.253.8.55.5.1.1.10
This object controls whether the printer is in a special diagnostic mode wherein all received print data is printed in hexadecimal format. Whether a reset or power-cycles turns xcmPrtGeneralHexDumpEnable to Off is product dependent.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtGeneralStartupPage 1.3.6.1.4.1.253.8.55.5.1.1.11
Used to enable or disable printing a startup page. If enabled, a startup page will be printed shortly after power-up, when the device is ready. Typical startup pages include test patterns and/or printer configuration information.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtGeneralBannerPage 1.3.6.1.4.1.253.8.55.5.1.1.12
Used to enable or disable printing banner pages at the beginning of jobs. This is a master switch which applies to all jobs, regardless of interpreter.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtGeneralScanlineCompaction 1.3.6.1.4.1.253.8.55.5.1.1.50
This object enables a printing mode wherein the printer compresses selected scanlines of raster image data as they are received and holds them in compressed form until they are to be printed. This allows particular jobs to be processed with less memory, but often reduced performance as well. On some Printers, turning this feature Off is referred to as 'PerformanceEnhancement'. When xcmInterpPageProtect is set to Off, some complex jobs may not print successfully with minimum memory. The ScanlineCompaction feature enables printing some complex jobs without resorting to reserving additional memory by turning on the PageProtect option or installing additional memory.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInputTable 1.3.6.1.4.1.253.8.55.8.1
This table logically augments the Printer MIB's prtInputTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtInputEntry

xcmPrtInputEntry 1.3.6.1.4.1.253.8.55.8.1.1
Entries may exist for each entry in the prtInputTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtInputEntry  

xcmPrtInputRowStatus 1.3.6.1.4.1.253.8.55.8.1.1.1
Manages the status of this conceptual row in the xcmPrtInputTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtInputNextPrtInputIndex 1.3.6.1.4.1.253.8.55.8.1.1.2
The value of prtInputIndex corresponding to the input subunit which will be used when this input subunit is emptied. The value of zero indicates that auto input switching will not occur when this input subunit is emptied. Two different mechanisms for input tray switching, xcmPrtNextPrtInputIndex and xcmPrtInputAliasGroup, are provided. A device agent may make use of one or the other, none, or both. Use the model that fits best for the given application.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xcmPrtOutputTable 1.3.6.1.4.1.253.8.55.9.1
This table logically augments the prtOutputTable in the Printer MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtOutputEntry

xcmPrtOutputEntry 1.3.6.1.4.1.253.8.55.9.1.1
Entries may exist for each entry in the prtOutputTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtOutputEntry  

xcmPrtOutputRowStatus 1.3.6.1.4.1.253.8.55.9.1.1.1
Manages the status of this conceptual row in the xcmPrtOutputTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtOutputNextIndex 1.3.6.1.4.1.253.8.55.9.1.1.2
The value of prtOutputIndex corresponding to the output subunit which will be used when this output subunit is filled. A value of zero(0) indicates that auto output switching will not occur when this output subunit is filled.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xcmPrtOutputPassword 1.3.6.1.4.1.253.8.55.9.1.1.3
This object is used as the password for an Output Tray, e.g. an output mailbox. It is the value that must be entered to open the output tray.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

xcmPrtOutputOffsetStackingType 1.3.6.1.4.1.253.8.55.9.1.1.4
This object further refines the type of offset stacking from that specified by the object prtOutputOffsetStacking in the Printer MIB.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtOutputOffsetStackingType  

xcmPrtOutputTrayTimeoutSupport 1.3.6.1.4.1.253.8.55.9.1.1.5
Determines whether the printer should wait before sending the printed output to another output destination when the selected or default destination is full. 'On' indicates that would should wait as specified by xcmPrtOutputTrayTimeout. 'Off' indicates this feature is off and should immediately seek to send the printed output to another destination. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtOutputTrayTimeout 1.3.6.1.4.1.253.8.55.9.1.1.6
Determines how long the printer should wait before sending the printed output to another output destination when the selected or default destination is full. A value of (0) implies 'other' or 'infinite' which translates to this input subunit does not support this feature.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtChannelTable 1.3.6.1.4.1.253.8.55.14.1
This table logically augments Printer MIB's prtChannelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtChannelEntry

xcmPrtChannelEntry 1.3.6.1.4.1.253.8.55.14.1.1
An entry exists corresponding to each entry in the prtChannelTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtChannelEntry  

xcmPrtChannelRowStatus 1.3.6.1.4.1.253.8.55.14.1.1.1
Manages the status of this conceptual row in the xcmPrtChannelTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtChannelEOJTimeout 1.3.6.1.4.1.253.8.55.14.1.1.2
Defines the number of seconds that the channel waits before timing out. For example, this may be used for the parallel channel. The value zero means infinite or no timeout on the channel.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtChannelAuxSheetPackage 1.3.6.1.4.1.253.8.55.14.1.1.3
This object is an index into the xcmPrtAuxPackageTable. This table is used to enable or disable printing of auxiliary sheets by this channel. The value zero shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtChannelSpoolingEnable 1.3.6.1.4.1.253.8.55.14.1.1.4
This object controls spooling to a large data store such as a hard disk. When set to On, data received and waiting to be processed from any port is spooled onto the large data store and later retrieved for processing. This allows the printer to receive the data more rapidly, thus freeing the data source sooner. It may also increase throughput by having the next job's print data already local for processing. When set to Off, the spooling feature is disabled. Data received is not spooled to the large data store, and is accepted by the printer only as needed for printing. You may want to disable this spooling feature if spooling is already done outside the printer; having the spooling done on the printer as well, may not add value, and may create error recovery and queue monitoring difficulties. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtChannelLangSensing 1.3.6.1.4.1.253.8.55.14.1.1.5
This object indicates whether the channel supports detection of the input PDL language type, and if so, whether the feature is enabled. Currently, the prtChannelDefaultPageDescLangIndex points to the Page Description Language Interpreter for this channel. One of the PDL types enumerated in the prtInterpreterLangFamily object is langAutomatic(37), to be used for automatic PDL sensing; however, if the language sensing fails there is no fallback language for the channel. Conforming implementations shall use xcmPrtChannelLangSensing for each channel and deprecate use of the langAutomatic(37) enum in favor of the literal default language in the prtInterpreterLangFamily object. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtChannelAutoJobEnd 1.3.6.1.4.1.253.8.55.14.1.1.80
Controls automatic ending of a print job that does not finish printing. When 'On', after the current print job has paused long enough to exceed the xcmPrtChannelEOJTimeout interval, the current print job will be stopped. When 'Off', the print job does not end after the timeout interval. Instead, the printer waits to continue until another print job is received on any port. A partial page will remain unprinted until the next print job is received. The current job will then be stopped. The value 'other' shall indicate not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpreterTable 1.3.6.1.4.1.253.8.55.15.1
This table logically augments the Printer MIB's prtInterpreterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtInterpreterEntry

xcmPrtInterpreterEntry 1.3.6.1.4.1.253.8.55.15.1.1
An entry exists corresponding to each entry in the prtInterpreterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtInterpreterEntry  

xcmPrtInterpRowStatus 1.3.6.1.4.1.253.8.55.15.1.1.1
Manages the status of this conceptual row in the xcmPrtInterpreterTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtInterpAuxSheetPackage 1.3.6.1.4.1.253.8.55.15.1.1.2
This object is an index into the xcmPrtAuxPackageTable. This table is used to enable or disable printing of auxiliary sheets by this interpreter. The value zero shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpContextSaving 1.3.6.1.4.1.253.8.55.15.1.1.3
Enables reserving memory for saving permanently downloaded fonts and macros, when the printer switches between this and another interpreter. The effect is to save the memory for a subsequent job using this interpreter. When set to Off, all permanently downloaded fonts and macros are cleared from memory when switching PDLs. They must be downloaded again when the printer switches back to using the current PDL. When set to On, permanently downloaded fonts and macros are stored in printer memory. You eliminate the time to download them again when the printer switches back to the current PDL. In PCL, this is referred to as Resource Savings. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpEdgeEnhancement 1.3.6.1.4.1.253.8.55.15.1.1.4
Specifies whether the printer should perform EdgeEnhancement of the image of the printed document for this interpreter. interpreter. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpFontIndexDefault 1.3.6.1.4.1.253.8.55.15.1.1.5
The value of xcmFontIndex corresponding to the xcmFontEntry which represents the default font for this Interpreter. A value of (-1) means 'other'. A value of (-2) means 'unknown'. A value of (-3) means 'notPresent'. A value of 'other' (-3) should be used for those interpreters which have no default font (e.g. PostScript). For agents that choose not to implement the Resources MIB, this object specifies the ID of the default font. This use of this object is significant only to the specific product.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

xcmPrtInterpGrayLevels 1.3.6.1.4.1.253.8.55.15.1.1.6
This object describes the gray levels supported by this interpreter. This may represent gray levels within a color plane. The value zero means not specified for this interpreter.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpGrayLevelDefault 1.3.6.1.4.1.253.8.55.15.1.1.7
This object controls the number of gray scales for this interpreter. The value zero means not specified for this interpreter.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpJamRecovery 1.3.6.1.4.1.253.8.55.15.1.1.8
This object controls how the printer recovers from a paper jam. When set to On, the printer reprints any pages in the printer at the time of the jam, after the jam has been cleared. The printer does this by using a portion of memory to store print data. This may slow throughput. When set to Off, some pages may be lost after the jam has been cleared. The print job must be re-sent, specifying those pages that did not print as a result of the paper jam. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpJobCopiesDefault 1.3.6.1.4.1.253.8.55.15.1.1.9
This defines the default number of job copies to be printed by this interpreter. If set incorrectly, this object may cause difficulties at customer sites. Agent developers should consider making this object read-only, permanently set to one copy.
Status: current Access: read-create
OBJECT-TYPE    
  Ordinal32  

xcmPrtInterpLineWrap 1.3.6.1.4.1.253.8.55.15.1.1.10
This object controls whether long lines are wrapped or truncated. If On, long lines wrap to the next line. If Off, long lines are truncated. Note the meaning of 'long' depends on the orientation and the current page size. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpMediumSizeDefault 1.3.6.1.4.1.253.8.55.15.1.1.11
This object specifies the default medium size for an interpreter. It is used if no medium size is specified. For PCL, this object sets the General PJL Environment variable 'Paper'. The xcmPrtInterpMediumSizeDefault object may be affected by setting the xcmPrtGeneralMediumClassDefault object.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediumSize  

xcmPrtInterpPageProtect 1.3.6.1.4.1.253.8.55.15.1.1.12
This object enables reserving sufficient memory for printing complex pages, thus avoiding Page Too Complex errors. The amount of memory reserved is implementation specific. When this feature is turned on, printer performance may be slowed. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpPageProtectSize 1.3.6.1.4.1.253.8.55.15.1.1.13
This object sets the PageSize to be used by this interpreter in reserving sufficient memory for printing complex pages, thus avoiding Page Too Complex Errors. The actual amount of memory to be reserved as a function of the specified page size is implementation specific. When this feature is turned on, printer performance may be slowed. In PCL, this object supports the General PJL Environment Variable 'PAGEPROTECT'. This object the sets the page protection configuration. The page protection feature reserves a block of printer memory to prevent printer overrun errors when formatting very dense or complex images. This variable may be set to any legal value at any time, regardless of the current amount of free memory or the currently set resolution. When a job is sent, if there is not enough memory to print correctly with the current resolution and page protection configuration, the system temporarily overrides the resolution and/or page protect values to run the job. When the page protection status is changed, memory may be reconfigured, and all downloaded fonts, PCL macros, and PostScript dictionaries may be lost. The value notSpecified shall also mean Off.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediumSize  

xcmPrtInterpPageSizeErrorPolicy 1.3.6.1.4.1.253.8.55.15.1.1.14
Controls interpreter behavior when the requested Page Size is not currently available.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPageSizeErrorPolicy  

xcmPrtInterpPlexSupported 1.3.6.1.4.1.253.8.55.15.1.1.15
This object specifies the Plex modes supported by this interpreter. These Plex modes specify the relative orientations between consecutive pages, and capabilities of printing one-side, two-sided or both.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPlex  

xcmPrtInterpPlexDefault 1.3.6.1.4.1.253.8.55.15.1.1.16
This object specifies the default plex for this interpreter. The device shall set no more than one bit. The value zero shall indicate not specified.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPlex  

xcmPrtInterpPrintEdgeToEdge 1.3.6.1.4.1.253.8.55.15.1.1.17
Enables edge to edge printing for interpreters that try to enforce a coordinate system that is offset from the edge of the paper, e.g., PCL. When On, jobs are printed to the edge of the paper. When Off, jobs are printed in normal printable area of page. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpPrintQuality 1.3.6.1.4.1.253.8.55.15.1.1.18
Sets the default output quality of the printed document for this interpreter. Some printers have programmatically controlled output quality.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPrintQuality  

xcmPrtInterpPrtInputIndexDflt 1.3.6.1.4.1.253.8.55.15.1.1.19
Sets the default input source for the interpreter. It is the index to the prtInputGroup. The value zero means not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPrtOutputIndexDflt 1.3.6.1.4.1.253.8.55.15.1.1.20
The value of the index of the default Output bin for this interpreter. If specified, this object overrides the box level object prtOutputDefaultIndex. The value zero means unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpResFeedDirDefault 1.3.6.1.4.1.253.8.55.15.1.1.21
This object specifies for this interpreter, the default resolution in the Feed direction in 10000 units of measure specified by prtMarkerAddressabilityUnit for this interpreter. A related object is the Printer MIB prtInterpreterFeedAddressability object which describes the maximum interpreter addressability in the feed direction. The value zero shall mean not specified. If this object has a value other than unspecified, this object takes precedence over xcmPrtInterpFeedResIndexDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpResXFeedDirDefault 1.3.6.1.4.1.253.8.55.15.1.1.22
This object specifies for this interpreter, the default resolution in the Cross Feed direction in 10000 units of measure specified by prtMarkerAddressabilityUnit for this interpreter. A related object is the Printer MIB prtInterpreterFeedAddressability object which describes the maximum interpreter addressability in the cross feed direction. The value zero means unspecified. If this object has a value other than unspecified, this object takes precedence over xcmPrtInterpFeedResIndexDefault.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpResIPResIndex 1.3.6.1.4.1.253.8.55.15.1.1.23
This object shall provide an index into the xcmIPResTable. The xcmIPResTable shall be used to list available resolutions supported by this interpreter. Each row includes objects for Feed Resolution (pixels per inch), XFeed Resolution (pixels per inch), Bits Per Pixel Supported, and Number of Color Planes Supported. The value zero means unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpResIPResIndexDflt 1.3.6.1.4.1.253.8.55.15.1.1.24
This object which is a pointer into the xcmIPResTable sets the print resolution for this interpreter. The value zero means unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpTextFormLength 1.3.6.1.4.1.253.8.55.15.1.1.25
This object sets the maximum number of lines per page for a text file that is being printed using this interpreter. For PCL Interpreters, this object provides the General PJL Environment Variable FORMLINES. This variable is tied to both the PJL Environment Variables PAPER and ORIENTATION. If the value of either of those variables is changed, then the FORMLINES variable automatically is updated to maintain the same line spacing. The value zero means not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpTimeoutJob 1.3.6.1.4.1.253.8.55.15.1.1.26
This object sets how long printer will wait for correct end of job from the interpreter. This setting lets you adjust how long the printer will wait to receive the data it needs to complete a job before terminating it prematurely. The value zero means infinite.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpTimeoutPage 1.3.6.1.4.1.253.8.55.15.1.1.27
This object sets how long printer will wait for correct end of page from the interpreter. If, for example, a print job contains a page without the correct end of page code, the job will stall. This setting lets you adjust how long the printer will wait to receive the data it needs to complete a page before terminating it prematurely. The value zero means infinite.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpInputAliasIndexDflt 1.3.6.1.4.1.253.8.55.15.1.1.28
Sets the default input tray alias for this interpreter. It is the xcmPrtInputAliasIndex to the xcmPrtInputAlias table. The value zero means 'not specified'.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpTraySwitch 1.3.6.1.4.1.253.8.55.15.1.1.29
This object declares for this interpreter the tray switching declaration mechanism used. Note: The tray switching declaration mechanisms do not specify how or when or whether a printer switches back to using an earlier emptied tray after that tray is refilled. For example, assume a printer is set up to first use Tray 1, then when emptied Tray 2, then Tray 3. If just after tray 1 becomes empty and the printer switches to Tray 2, the operator refills Tray 1; the printer may select which tray to pull the next sheet from using a variety of algorithms: - The printer may switch back immediately to use tray 1. This may be particularly appropriate if tray 1 is the high capacity feeder. - The printer may pull sheets from tray 2 until it is empty and then switch back to tray 1. - The printer may pull sheets from tray 2 until it is empty and then continue to tray 3, before switching back to tray 1. Again, implementation of how the input tray switching programs behave when empty trays are refilled is considered printer specific.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtTraySwitch  

xcmPrtInterpMediumTypeDefault 1.3.6.1.4.1.253.8.55.15.1.1.30
Specifies the paper type used to print a page if no paper type is specified by the software application Typical paper types could include Plain, Preprinted, etc.
Status: current Access: read-create
OBJECT-TYPE    
  XcmFixedLocaleDisplayString Size(0..255)  

xcmPrtInterpMediaTypeErrPolicy 1.3.6.1.4.1.253.8.55.15.1.1.31
Controls interpreter behavior when the requested Media Type is not currently available.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediaTypeErrorPolicy  

xcmPrtInterpErrorPolicyTimeout 1.3.6.1.4.1.253.8.55.15.1.1.32
Provides the timeout for ErrorPolicy enumerations requiring one, e.g. 'ignoreAfterTimeout' The value zero shall mean infinite or not supported.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpLineTerm 1.3.6.1.4.1.253.8.55.15.1.1.33
Enables adding a Carriage Return after every Line Feed. The value 'On' indicates that a Carriage Return will be added after every Line Feed. Usage example: This is a useful feature when printing text jobs via PCL through a standard queue in UNIX. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpAutoContinue 1.3.6.1.4.1.253.8.55.15.1.1.50
This object controls whether the printer resumes printing after a system error occurs. When set to Off, the printer does not automatically resume. Manual intervention must occur for the printer to resume. When set to On, the printer automatically resumes operation after certain system errors. The On setting is useful in a networked environment. The value 'other' shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  PresentOnOff  

xcmPrtInterpEnvFeederSize 1.3.6.1.4.1.253.8.55.15.1.1.51
This object informs the printer what size of envelope is currently loaded in the envelope feeder. Because the input tray feeding envelopes may not have a size sensor, this setting is required so that the printer is able to know when the size of envelope requested for printing is different than that loaded. When the sizes do not match, and xcmPrtInterpPageSizeErrorPolicy is set to Off, the printer displays a message asking for a change of envelope size. The XcmPrtPaperSize selected should be that of an envelope.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediumSize  

xcmPrtInterpManualFeedPgSize 1.3.6.1.4.1.253.8.55.15.1.1.52
This object sets the default medium size of the manual input tray for this interpreter.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtMediumSize  

xcmPrtInterpOffsetStackingType 1.3.6.1.4.1.253.8.55.15.1.1.53
This object further refines the type of offset stacking from that specified by the object prtOutputOffsetStacking in the Printer MIB. Printers who need to specify OffsetStackingType by interpreter shall set this object to 'other'. To specify OffsetStackingType by interpreter, use the object xcmPrtOutputOffsetStackingType.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtOutputOffsetStackingType  

xcmPrtInputAliasTable 1.3.6.1.4.1.253.8.55.50.1
This table defines one or more aliases for input sub-units defined in the Input Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtInputAliasEntry

xcmPrtInputAliasEntry 1.3.6.1.4.1.253.8.55.50.1.1
One or more entries may exist corresponding to each entry in the prtInputTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtInputAliasEntry  

xcmPrtInputAliasIndex 1.3.6.1.4.1.253.8.55.50.1.1.1
A unique value used to identify this row in the xcmPrtInputAliasTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Cardinal32  

xcmPrtInputAliasRowStatus 1.3.6.1.4.1.253.8.55.50.1.1.2
Manages the status of this conceptual row in the xcmPrtInputAliasTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtInputAliasName 1.3.6.1.4.1.253.8.55.50.1.1.3
Defines an alternate name for the input source. This is in addition to the prtInputName from the Input Group. Typical usage is to map an interpreter specific name to the sub-unit name in the Input Group, e.g., PCL's 'upper' to the device input name 'main'.
Status: current Access: read-create
OBJECT-TYPE    
  XcmFixedLocaleDisplayString Size(0..63)  

xcmPrtInputAliasSwitchProgram 1.3.6.1.4.1.253.8.55.50.1.1.4
The input tray switching program for this 'InputAliasName' presented in a '.' separated list of prtInputIndex values. For example, the string '1.4.3' indicates start with the input tray represented by prtInputIndex 1, if it becomes empty switch to prtInputIndex 4, when it becomes empty switch to prtInputIndex 3, if it becomes empty then wait for operator intervention. An empty string shall indicate unspecified.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..255)  

xcmPrtInterpPCLTable 1.3.6.1.4.1.253.8.55.70.1
This table is an extension to the prtInterpPCLTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtInterpPCLEntry

xcmPrtInterpPCLEntry 1.3.6.1.4.1.253.8.55.70.1.1
An entry exists corresponding to each entry in the xcmPrtInterpPCLTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtInterpPCLEntry  

xcmPrtInterpPCLRowStatus 1.3.6.1.4.1.253.8.55.70.1.1.1
Manages the status of this conceptual row in the xcmPrtInterpPCLTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtInterpPCLFontSourceDflt 1.3.6.1.4.1.253.8.55.70.1.1.2
This object provides the PCL-specific PJL variable 'FONTSOURCE'. 'FONTSOURCE' specifies the device location of the default font in PCL.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPCLFontSource  

xcmPrtInterpPCLFontNumberDflt 1.3.6.1.4.1.253.8.55.70.1.1.3
This object provides the PCL-specific PJL variable 'FONTNUMBER'. In PCL, 'FONTNUMBER' specifies the ID of the default font within the default FONTSOURCE.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPCLPitchNumerator 1.3.6.1.4.1.253.8.55.70.1.1.4
This object along with xcmPrtInterpPCLPitchDenominator sets the default for the PCL-specific PJL variable 'PITCH. These two object sets the default pitch size for the PCL default font defined in xcmPrtInterpreterPCLFontNumberDflt. This variable only applies when the default font specified is a scalable fixed pitch font. A value of zero shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPCLPitchDenominator 1.3.6.1.4.1.253.8.55.70.1.1.5
This object along with xcmPrtInterpPCLPitchNumerator sets the default for the PCL-specific PJL variable 'PITCH'. These two object sets the default pitch size for the PCL default font defined in xcmPrtInterpreterPCLFontNumberDflt. The PITCH variable only applies when the default font specified is a scalable fixed pitch font. A value of zero shall mean not specified. It is expected that a typical application will set xcmPrtInterpPCLPitchDenominator to 100.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPCLPtSizeNumerator 1.3.6.1.4.1.253.8.55.70.1.1.6
This object along with xcmPrtInterpPCLPtSizeDenominatr sets the default for the PCL-specific PJL variable 'PTSIZE'. The PTSIZE variable only applies when the FONTNUMBER setting specifies a scalable proportionally-spaced font. The size is in units of printer's points, which units are here considered to be exactly 1/72 of an inch. The value zero shall mean not specified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPCLPtSizeDenominatr 1.3.6.1.4.1.253.8.55.70.1.1.7
This object along with xcmPrtInterpPCLPtSizeNumerator sets the default for the PCL-specific PJL variable 'PTSIZE'. The PTSIZE variable only applies when the FONTNUMBER setting specifies a scalable proportionally-spaced font. The value zero shall mean not specified. It is expected that a typical application will set this object to the value 4. For example, if the denominator is set to 4, describe a PtSize of 8.5, xcmPrtInterpPCLPtSizeNominator must be set to 34.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtInterpPCLPrintScreen 1.3.6.1.4.1.253.8.55.70.1.1.50
This object sets a special mode for 80 character screen dumps.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtPrintScreen  

xcmPrtAuxPackageTable 1.3.6.1.4.1.253.8.55.60.1
This table lists Auxiliary Sheets enabled for this printer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtAuxPackageEntry

xcmPrtAuxPackageEntry 1.3.6.1.4.1.253.8.55.60.1.1
An entry exists corresponding to each entry in the xcmPrtAuxPackageTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtAuxPackageEntry  

xcmPrtAuxPackageIndex 1.3.6.1.4.1.253.8.55.60.1.1.1
A unique value used by the printer to identify this Auxiliary Sheet.
Status: current Access: not-accessible
OBJECT-TYPE    
  Cardinal32  

xcmPrtAuxPackageRowStatus 1.3.6.1.4.1.253.8.55.60.1.1.2
Manages the status of this conceptual row in the xcmPrtAuxPackageTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtAuxPackageType 1.3.6.1.4.1.253.8.55.60.1.1.3
Specifies the Auxiliary Sheet type associated with this row.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtAuxSheetType  

xcmPrtAuxPackageContent 1.3.6.1.4.1.253.8.55.60.1.1.4
Specifies the information content of this auxiliary sheet. The value zero shall mean notSpecified.
Status: current Access: read-create
OBJECT-TYPE    
  XcmPrtAuxSheetContent  

xcmPrtAuxPackagePrtInputIndex 1.3.6.1.4.1.253.8.55.60.1.1.5
Specifies the input tray the printer shall use in printing this auxiliary sheet. The value zero shall mean notSpecified.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtAuxPackageNext 1.3.6.1.4.1.253.8.55.60.1.1.6
Provides the index of the next Auxiliary Sheet declared for this printer. This provides a linking mechanism to group auxiliary pages. The last auxiliary page to be declared will set this xcmPrtAuxPackageNext object to zero, meaning no further sheets. The value zero shall mean notPresent.
Status: current Access: read-create
OBJECT-TYPE    
  Cardinal32  

xcmPrtMedmTypeSupTable 1.3.6.1.4.1.253.8.55.75.2
A table of specific and general medium 'types' which are associated with this host system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XcmPrtMedmTypeSupEntry

xcmPrtMedmTypeSupEntry 1.3.6.1.4.1.253.8.55.75.2.1
An entry for a specific or general medium 'types' which is associated with this host system.
Status: current Access: not-accessible
OBJECT-TYPE    
  XcmPrtMedmTypeSupEntry  

xcmPrtMedmTypeSupIndex 1.3.6.1.4.1.253.8.55.75.2.1.1
A unique value used to identify this medium type supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  Ordinal32  

xcmPrtMedmTypeSupRowStatus 1.3.6.1.4.1.253.8.55.75.2.1.2
Manages the status of this conceptual row in the 'xcmPrtMedmTypeSupTable'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xcmPrtMedmTypeSupRowPersistence 1.3.6.1.4.1.253.8.55.75.2.1.3
Indicates persistence of this row, from the given enumeration.
Status: current Access: read-create
OBJECT-TYPE    
  XcmGenRowPersistence  

xcmPrtMedmTypeSupName 1.3.6.1.4.1.253.8.55.75.2.1.4
Named 'type' of this medium instance.
Status: current Access: read-create
OBJECT-TYPE    
  XcmFixedLocaleDisplayString Size(0..255)  

xcmPrtMIBConformance 1.3.6.1.4.1.253.8.55.2
OBJECT IDENTIFIER    

xcmPrtMIBCompliance 1.3.6.1.4.1.253.8.55.2.1
The compliance statement for agents that implement the printer MIB extension module.
Status: current Access: read-only
MODULE-COMPLIANCE    

xcmPrtMIBGroups 1.3.6.1.4.1.253.8.55.2.2
OBJECT IDENTIFIER    

xcmPrtBaseGroup 1.3.6.1.4.1.253.8.55.2.2.1
The general printer group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtGeneralGroup 1.3.6.1.4.1.253.8.55.2.2.5
The general printer group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInputGroup 1.3.6.1.4.1.253.8.55.2.2.8
The input group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtOutputGroup 1.3.6.1.4.1.253.8.55.2.2.9
The output group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtChannelGroup 1.3.6.1.4.1.253.8.55.2.2.14
The Channel group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInterpreterGroup 1.3.6.1.4.1.253.8.55.2.2.15
The interpreter group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInputAliasGroup 1.3.6.1.4.1.253.8.55.2.2.50
The Input Alias group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtGeneralAuxSheetGroup 1.3.6.1.4.1.253.8.55.2.2.52
The General Auxiliary Sheet group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtGeneralProdSpecificGroup 1.3.6.1.4.1.253.8.55.2.2.55
The general printer product specific group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtAuxPackageGroup 1.3.6.1.4.1.253.8.55.2.2.60
The Auxiliary Package group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtChannelProdSpecificGroup 1.3.6.1.4.1.253.8.55.2.2.64
The Channel group extension for prod specific objects.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInterpProdSpecificGroup 1.3.6.1.4.1.253.8.55.2.2.65
The interpreter group extension.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInterpPCLGroup 1.3.6.1.4.1.253.8.55.2.2.70
The Interpreter PCL group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtInterpPCLProdSpecificGroup 1.3.6.1.4.1.253.8.55.2.2.71
The Interpreter PCL Product Specific group.
Status: current Access: read-only
OBJECT-GROUP    

xcmPrtMediumTypeSupportedGroup 1.3.6.1.4.1.253.8.55.2.2.75
The Medium Type Supported group.
Status: current Access: read-only
OBJECT-GROUP