XLDV20PM-MIB

File: XLDV20PM-MIB.mib (263799 bytes)

Imported modules

RFC-1212 RFC-1215 RFC1155-SMI
AN-MIB XLDV20-MIB SNMPv2-SMI

Imported symbols

OBJECT-TYPE TRAP-TYPE Counter
TimeTicks Gauge onu
Xldv20ControlStatus Xldv20AdminState Xldv20FlowDirection
Unsigned16 xldv20IfIndex xldv20TvTimeAndDate
xldv20Traps Unsigned32

Defined Types

Xldv20pmIntervalType  
INTEGER min15(1), day(2)    

Xldv20pmControlReq  
INTEGER noRequest(1), resetIndividCurrent(2), setNrHistEntriesSize(3), paramFaulty(4), nrHistEntriesSizeNotAcceptable(5), dataDaseMemoryNotAvailable(6), create(7), delete(8), addEndpoint(9), removeEndpoint(10), indexLimitExceeded(11), atmPmObjectActive(12), atmPmObjectNotExists(13), endpointExistsAlready(14), requestBusy(15), setDataFailed(16), aswTimeout(17), commandFailed(18), commandSucceeded(19)    

Xldv20pmCounterName  
INTEGER noPmCounter(0), neBackgroundBlockErrors(1), neCodeViolations(2), neCodeViolationsCP(3), neCodeViolationsP(4), neCodeViolationsPLCP(5), neErroredSeconds(6), neErroredSecondsCP(7), neErroredSecondsPLCP(8), neSas(9), neSeverelyErroredFrameSeconds(10), neSeverelyErroredSeconds(11), neSeverelyErroredSecondsCP(12), neSeverelyErroredSecondsPLCP(13), neUnavailableSeconds(14), neUnavailableSecondsPLCP(15), neAisSeconds(16), neOfsSeconds(17), neLosSeconds(18), feBackgroundBlockErrors(19), feCodeViolations(20), feCodeViolationsCP(21), feCodeViolationsPLCP(22), feErroredSeconds(23), feErroredSecondsCP(24), feErroredSecondsPLCP(25), feSas(26), feSeverelyErroredSeconds(27), feSeverelyErroredSecondsCP(28), feSeverelyErroredSecondsPLCP(29), feUnavailableSeconds(30), feUnavailableSecondsPLCP(31), discardedCells(32), imaGroupUnavailSecs(33), imaGroupNeNumFailures(34), imaLinkImaViolations(35), imaLinkOifAnomalies(36), imaLinkNeSevErroredSecs(37), imaLinkFeSevErroredSecs(38), imaLinkNeUnavailSecs(39), imaLinkFeUnavailSecs(40), imaLinkNeTxUnusableSecs(41), imaLinkNeRxUnusableSecs(42), imaLinkFeTxUnusableSecs(43), imaLinkFeRxUnusableSecs(44), imaLinkNeTxNumFailures(45), imaLinkNeRxNumFailures(46), maxPmCounter(47)    

Xldv20pmType  
INTEGER pmTypeUnknown(0), s1F1PMo(1), s1F2PMo(2), s1F3PMo(3), s3F1PMo(4), s3F2PMo(5), s3F3PMo(6), d3F2PMo(7), d3F3PMo(8), e3F3PMo(9), adcF3PMo(10), s1PrM(11), s3PrM(12), e3PrM(13), d3PrM(14), adcPrM(15), e1ImaPrM(16), d1ImaPrM(17), e1ImaPMo(18), d1ImaPMo(19), atmImaPMo(20), maxPmType(21)    

Xldv20pmFlowType  
INTEGER undefined(0), f4Segment(1), f4EndToEnd(2), f5Segment(3), f5EndToEnd(4)    

Xldv20pmSuspectType  
INTEGER undefined(0), reliable(1), suspect(2)    

Xldv20pmConnectionIndexType  
INTEGER undefined(0), vplUni(1), vplNni(2), vclUni(3), vclNni(4)    

Xldv20pmRoleType  
INTEGER undefined(0), analyseWithBackwardReporting(1), analyseWithoutBackwardReporting(2), generateWithCollect(3), generateWithoutCollect(4)    

Xldv20pmEndpointType  
INTEGER source(1), sink(2)    

Xldv20pmBlockSizeType  
INTEGER undefined(0), blockSize128(128), blockSize256(256), blockSize512(512), blockSize1024(1024)    

Xldv20pmAtmCounterType  
INTEGER transmittedUserCells(1), lostUserCells(2), misinsertedUserCells(3)    

Xldv20pmCommonCurrentEntry  
SEQUENCE    
  xldv20pmCcIntervalType Xldv20pmIntervalType
  xldv20pmCcOAMLevel INTEGER
  xldv20pmCcAdminState Xldv20AdminState
  xldv20pmCcSuspectFlag Xldv20pmSuspectType
  xldv20pmCcHistEntrySize INTEGER
  xldv20pmCcNrHistEntriesAvailable INTEGER
  xldv20pmCcElapsedTime INTEGER
  xldv20pmCcThresholdLimitIndex INTEGER
  xldv20pmCcNeErroredSeconds Counter
  xldv20pmCcFeErroredSeconds Counter
  xldv20pmCcNeSeverelyErroredSeconds Counter
  xldv20pmCcFeSeverelyErroredSeconds Counter
  xldv20pmCcNeBackgroundBlockErrors Counter
  xldv20pmCcFeBackgroundBlockErrors Counter
  xldv20pmCcNeUnavailableSeconds Counter
  xldv20pmCcFeUnavailableSeconds Counter

Xldv20pmCommonHistoryEntry  
SEQUENCE    
  xldv20pmChIntervalType Xldv20pmIntervalType
  xldv20pmChOAMLevel INTEGER
  xldv20pmChHistEntryNr INTEGER
  xldv20pmChSuspectFlag Xldv20pmSuspectType
  xldv20pmChPeriodEndTime INTEGER
  xldv20pmChNeErroredSeconds Counter
  xldv20pmChFeErroredSeconds Counter
  xldv20pmChNeSeverelyErroredSeconds Counter
  xldv20pmChFeSeverelyErroredSeconds Counter
  xldv20pmChNeBackgroundBlockErrors Counter
  xldv20pmChFeBackgroundBlockErrors Counter
  xldv20pmChNeUnavailableSeconds Counter
  xldv20pmChFeUnavailableSeconds Counter

Xldv20pmS3CurrentEntry  
SEQUENCE    
  xldv20pmS3cIntervalType Xldv20pmIntervalType
  xldv20pmS3cOAMLevel INTEGER
  xldv20pmS3cAdminState Xldv20AdminState
  xldv20pmS3cSuspectFlag Xldv20pmSuspectType
  xldv20pmS3cHistEntrySize INTEGER
  xldv20pmS3cNrHistEntriesAvailable INTEGER
  xldv20pmS3cElapsedTime INTEGER
  xldv20pmS3cThresholdLimitIndex INTEGER
  xldv20pmS3cNeErroredSeconds Counter
  xldv20pmS3cFeErroredSeconds Counter
  xldv20pmS3cNeSeverelyErroredSeconds Counter
  xldv20pmS3cFeSeverelyErroredSeconds Counter
  xldv20pmS3cNeCodeViolations Counter
  xldv20pmS3cFeCodeViolations Counter
  xldv20pmS3cNeUnavailableSeconds Counter
  xldv20pmS3cFeUnavailableSeconds Counter
  xldv20pmS3cNeSeverelyErroredFrameSeconds Counter

Xldv20pmS3HistoryEntry  
SEQUENCE    
  xldv20pmS3hIntervalType Xldv20pmIntervalType
  xldv20pmS3hOAMLevel INTEGER
  xldv20pmS3hHistEntryNr INTEGER
  xldv20pmS3hSuspectFlag Xldv20pmSuspectType
  xldv20pmS3hPeriodEndTime INTEGER
  xldv20pmS3hNeErroredSeconds Counter
  xldv20pmS3hFeErroredSeconds Counter
  xldv20pmS3hNeSeverelyErroredSeconds Counter
  xldv20pmS3hFeSeverelyErroredSeconds Counter
  xldv20pmS3hNeCodeViolations Counter
  xldv20pmS3hFeCodeViolations Counter
  xldv20pmS3hNeUnavailableSeconds Counter
  xldv20pmS3hFeUnavailableSeconds Counter
  xldv20pmS3hNeSeverelyErroredFrameSeconds Counter

Xldv20pmD3CurrentEntry  
SEQUENCE    
  xldv20pmD3cIntervalType Xldv20pmIntervalType
  xldv20pmD3cOAMLevel INTEGER
  xldv20pmD3cAdminState Xldv20AdminState
  xldv20pmD3cSuspectFlag Xldv20pmSuspectType
  xldv20pmD3cHistEntrySize INTEGER
  xldv20pmD3cNrHistEntriesAvailable INTEGER
  xldv20pmD3cElapsedTime INTEGER
  xldv20pmD3cThresholdLimitIndex INTEGER
  xldv20pmD3cNeErroredSecondsCP Counter
  xldv20pmD3cFeErroredSecondsCP Counter
  xldv20pmD3cNeErroredSecondsPLCP Counter
  xldv20pmD3cFeErroredSecondsPLCP Counter
  xldv20pmD3cNeSeverelyErroredSecondsCP Counter
  xldv20pmD3cFeSeverelyErroredSecondsCP Counter
  xldv20pmD3cNeSeverelyErroredSecondsPLCP Counter
  xldv20pmD3cFeSeverelyErroredSecondsPLCP Counter
  xldv20pmD3cNeCodeViolationsP Counter
  xldv20pmD3cNeCodeViolationsCP Counter
  xldv20pmD3cFeCodeViolationsCP Counter
  xldv20pmD3cNeCodeViolationsPLCP Counter
  xldv20pmD3cFeCodeViolationsPLCP Counter
  xldv20pmD3cNeUnavailableSeconds Counter
  xldv20pmD3cFeUnavailableSeconds Counter
  xldv20pmD3cNeUnavailableSecondsPLCP Counter
  xldv20pmD3cFeUnavailableSecondsPLCP Counter
  xldv20pmD3cNeSas Counter
  xldv20pmD3cFeSas Counter

Xldv20pmD3HistoryEntry  
SEQUENCE    
  xldv20pmD3hIntervalType Xldv20pmIntervalType
  xldv20pmD3hOAMLevel INTEGER
  xldv20pmD3hHistEntryNr INTEGER
  xldv20pmD3hSuspectFlag Xldv20pmSuspectType
  xldv20pmD3hPeriodEndTime INTEGER
  xldv20pmD3hNeErroredSecondsCP Counter
  xldv20pmD3hFeErroredSecondsCP Counter
  xldv20pmD3hNeErroredSecondsPLCP Counter
  xldv20pmD3hFeErroredSecondsPLCP Counter
  xldv20pmD3hNeSeverelyErroredSecondsCP Counter
  xldv20pmD3hFeSeverelyErroredSecondsCP Counter
  xldv20pmD3hNeSeverelyErroredSecondsPLCP Counter
  xldv20pmD3hFeSeverelyErroredSecondsPLCP Counter
  xldv20pmD3hNeCodeViolationsP Counter
  xldv20pmD3hNeCodeViolationsCP Counter
  xldv20pmD3hFeCodeViolationsCP Counter
  xldv20pmD3hNeCodeViolationsPLCP Counter
  xldv20pmD3hFeCodeViolationsPLCP Counter
  xldv20pmD3hNeUnavailableSeconds Counter
  xldv20pmD3hFeUnavailableSeconds Counter
  xldv20pmD3hNeUnavailableSecondsPLCP Counter
  xldv20pmD3hFeUnavailableSecondsPLCP Counter
  xldv20pmD3hNeSas Counter
  xldv20pmD3hFeSas Counter

Xldv20pmS1CurrentEntry  
SEQUENCE    
  xldv20pmS1cIntervalType Xldv20pmIntervalType
  xldv20pmS1cOAMLevel INTEGER
  xldv20pmS1cAdminState Xldv20AdminState
  xldv20pmS1cSuspectFlag Xldv20pmSuspectType
  xldv20pmS1cHistEntrySize INTEGER
  xldv20pmS1cNrHistEntriesAvailable INTEGER
  xldv20pmS1cElapsedTime INTEGER
  xldv20pmS1cThresholdLimitIndex INTEGER
  xldv20pmS1cNeErroredSeconds Counter
  xldv20pmS1cFeErroredSeconds Counter
  xldv20pmS1cNeSeverelyErroredSeconds Counter
  xldv20pmS1cFeSeverelyErroredSeconds Counter
  xldv20pmS1cNeBackgroundBlockErrors Counter
  xldv20pmS1cFeBackgroundBlockErrors Counter
  xldv20pmS1cNeUnavailableSeconds Counter
  xldv20pmS1cFeUnavailableSeconds Counter
  xldv20pmS1cNeOfsSeconds Counter
  xldv20pmS1cNeAisSeconds Counter
  xldv20pmS1cNeLosSeconds Counter

Xldv20pmS1HistoryEntry  
SEQUENCE    
  xldv20pmS1hIntervalType Xldv20pmIntervalType
  xldv20pmS1hOAMLevel INTEGER
  xldv20pmS1hHistEntryNr INTEGER
  xldv20pmS1hSuspectFlag Xldv20pmSuspectType
  xldv20pmS1hPeriodEndTime INTEGER
  xldv20pmS1hNeErroredSeconds Counter
  xldv20pmS1hFeErroredSeconds Counter
  xldv20pmS1hNeSeverelyErroredSeconds Counter
  xldv20pmS1hFeSeverelyErroredSeconds Counter
  xldv20pmS1hNeBackgroundBlockErrors Counter
  xldv20pmS1hFeBackgroundBlockErrors Counter
  xldv20pmS1hNeUnavailableSeconds Counter
  xldv20pmS1hFeUnavailableSeconds Counter
  xldv20pmS1hNeOfsSeconds Counter
  xldv20pmS1hNeAisSeconds Counter
  xldv20pmS1hNeLosSeconds Counter

Xldv20pmAtmObjectsEntry  
SEQUENCE    
  xldv20pmAoIndex INTEGER
  xldv20pmAoFlowType Xldv20pmFlowType
  xldv20pmAoAdminState Xldv20AdminState
  xldv20pmAoBlockSize Xldv20pmBlockSizeType

Xldv20pmAtmEndpointsEntry  
SEQUENCE    
  xldv20pmAeEndpointType Xldv20pmEndpointType
  xldv20pmAeConnectionIndex INTEGER
  xldv20pmAeConnectionIndexType Xldv20pmConnectionIndexType
  xldv20pmAeRole Xldv20pmRoleType
  xldv20pmAeFlowDirection Xldv20FlowDirection

Xldv20pmAtmCurrentEntry  
SEQUENCE    
  xldv20pmAcIntervalType Xldv20pmIntervalType
  xldv20pmAcAdminState Xldv20AdminState
  xldv20pmAcSuspectFlag Xldv20pmSuspectType
  xldv20pmAcHistEntrySize INTEGER
  xldv20pmAcNrHistEntriesAvailable INTEGER
  xldv20pmAcElapsedTime INTEGER
  xldv20pmAcThresholdLimitIndex INTEGER
  xldv20pmAcTransmittedUserCells Counter
  xldv20pmAcLostUserCells Counter
  xldv20pmAcMisinsertedUserCells Counter

Xldv20pmAtmHistoryEntry  
SEQUENCE    
  xldv20pmAhIntervalType Xldv20pmIntervalType
  xldv20pmAhHistEntryNr INTEGER
  xldv20pmAhSuspectFlag Xldv20pmSuspectType
  xldv20pmAhPeriodEndTime INTEGER
  xldv20pmAhTransmittedUserCells Counter
  xldv20pmAhLostUserCells Counter
  xldv20pmAhMisinsertedUserCells Counter

Xldv20pmImaGroupCurrentEntry  
SEQUENCE    
  xldv20pmImaGroupCurrentIntervalType Xldv20pmIntervalType
  xldv20pmImaGroupCurrentAdminState Xldv20AdminState
  xldv20pmImaGroupCurrentSuspectFlag Xldv20pmSuspectType
  xldv20pmImaGroupCurrentHistEntrySize INTEGER
  xldv20pmImaGroupCurrentNrHistEntriesAvailable INTEGER
  xldv20pmImaGroupCurrentElapsedTime INTEGER
  xldv20pmImaGroupCurrentThresholdLimitIndex INTEGER
  xldv20pmImaGroupCurrentUnavailSecs Gauge
  xldv20pmImaGroupCurrentNeNumFailures Gauge

Xldv20pmImaGroupHistoryEntry  
SEQUENCE    
  xldv20pmImaGroupHistoryIntervalType Xldv20pmIntervalType
  xldv20pmImaGroupHistoryHistEntryNr INTEGER
  xldv20pmImaGroupHistorySuspectFlag Xldv20pmSuspectType
  xldv20pmImaGroupHistoryPeriodEndTime INTEGER
  xldv20pmImaGroupHistoryUnavailSecs Gauge
  xldv20pmImaGroupHistoryNeNumFailures Gauge

Xldv20pmImaLinkCurrentEntry  
SEQUENCE    
  xldv20pmImaLinkCurrentIntervalType Xldv20pmIntervalType
  xldv20pmImaLinkCurrentAdminState Xldv20AdminState
  xldv20pmImaLinkCurrentSuspectFlag Xldv20pmSuspectType
  xldv20pmImaLinkCurrentHistEntrySize INTEGER
  xldv20pmImaLinkCurrentNrHistEntriesAvailable INTEGER
  xldv20pmImaLinkCurrentElapsedTime INTEGER
  xldv20pmImaLinkCurrentThresholdLimitIndex INTEGER
  xldv20pmImaLinkCurrentImaViolations Gauge
  xldv20pmImaLinkCurrentOifAnomalies Gauge
  xldv20pmImaLinkCurrentNeSevErroredSecs Gauge
  xldv20pmImaLinkCurrentFeSevErroredSecs Gauge
  xldv20pmImaLinkCurrentNeUnavailSecs Gauge
  xldv20pmImaLinkCurrentFeUnavailSecs Gauge
  xldv20pmImaLinkCurrentNeTxUnusableSecs Gauge
  xldv20pmImaLinkCurrentNeRxUnusableSecs Gauge
  xldv20pmImaLinkCurrentFeTxUnusableSecs Gauge
  xldv20pmImaLinkCurrentFeRxUnusableSecs Gauge
  xldv20pmImaLinkCurrentNeTxNumFailures Gauge
  xldv20pmImaLinkCurrentNeRxNumFailures Gauge

Xldv20pmImaLinkHistoryEntry  
SEQUENCE    
  xldv20pmImaLinkHistoryIntervalType Xldv20pmIntervalType
  xldv20pmImaLinkHistoryHistEntryNr INTEGER
  xldv20pmImaLinkHistorySuspectFlag Xldv20pmSuspectType
  xldv20pmImaLinkHistoryPeriodEndTime INTEGER
  xldv20pmImaLinkHistoryImaViolations Gauge
  xldv20pmImaLinkHistoryOifAnomalies Gauge
  xldv20pmImaLinkHistoryNeSevErroredSecs Gauge
  xldv20pmImaLinkHistoryFeSevErroredSecs Gauge
  xldv20pmImaLinkHistoryNeUnavailSecs Gauge
  xldv20pmImaLinkHistoryFeUnavailSecs Gauge
  xldv20pmImaLinkHistoryNeTxUnusableSecs Gauge
  xldv20pmImaLinkHistoryNeRxUnusableSecs Gauge
  xldv20pmImaLinkHistoryFeTxUnusableSecs Gauge
  xldv20pmImaLinkHistoryFeRxUnusableSecs Gauge
  xldv20pmImaLinkHistoryNeTxNumFailures Gauge
  xldv20pmImaLinkHistoryNeRxNumFailures Gauge

Xldv20pmTcaPrMCurrentEntry  
SEQUENCE    
  xldv20pmTcIntervalType Xldv20pmIntervalType
  xldv20pmTcAdminState Xldv20AdminState
  xldv20pmTcSuspectFlag Xldv20pmSuspectType
  xldv20pmTcHistEntrySize INTEGER
  xldv20pmTcNrHistEntriesAvailable INTEGER
  xldv20pmTcElapsedTime INTEGER
  xldv20pmTcThresholdLimitIndex INTEGER
  xldv20pmTcDiscardedCells Counter

Xldv20pmTcaPrMHistoryEntry  
SEQUENCE    
  xldv20pmThIntervalType Xldv20pmIntervalType
  xldv20pmThHistEntryNr INTEGER
  xldv20pmThSuspectFlag Xldv20pmSuspectType
  xldv20pmThPeriodEndTime INTEGER
  xldv20pmThDiscardedCells Counter

Xldv20pmThresholdLimitEntry  
SEQUENCE    
  xldv20pmThlThresholdLimitIndex INTEGER
  xldv20pmThlNeBackgroundBlockErrors INTEGER
  xldv20pmThlNeCodeViolations INTEGER
  xldv20pmThlNeCodeViolationsCP INTEGER
  xldv20pmThlNeCodeViolationsP INTEGER
  xldv20pmThlNeCodeViolationsPLCP INTEGER
  xldv20pmThlNeErroredSeconds INTEGER
  xldv20pmThlNeErroredSecondsCP INTEGER
  xldv20pmThlNeErroredSecondsPLCP INTEGER
  xldv20pmThlNeSas INTEGER
  xldv20pmThlNeSeverelyErroredFrameSeconds INTEGER
  xldv20pmThlNeSeverelyErroredSeconds INTEGER
  xldv20pmThlNeSeverelyErroredSecondsCP INTEGER
  xldv20pmThlNeSeverelyErroredSecondsPLCP INTEGER
  xldv20pmThlNeUnavailableSeconds INTEGER
  xldv20pmThlNeUnavailableSecondsPLCP INTEGER
  xldv20pmThlNeAisSeconds INTEGER
  xldv20pmThlNeOfsSeconds INTEGER
  xldv20pmThlNeLosSeconds INTEGER
  xldv20pmThlFeBackgroundBlockErrors INTEGER
  xldv20pmThlFeCodeViolations INTEGER
  xldv20pmThlFeCodeViolationsCP INTEGER
  xldv20pmThlFeCodeViolationsPLCP INTEGER
  xldv20pmThlFeErroredSeconds INTEGER
  xldv20pmThlFeErroredSecondsCP INTEGER
  xldv20pmThlFeErroredSecondsPLCP INTEGER
  xldv20pmThlFeSas INTEGER
  xldv20pmThlFeSeverelyErroredSeconds INTEGER
  xldv20pmThlFeSeverelyErroredSecondsCP INTEGER
  xldv20pmThlFeSeverelyErroredSecondsPLCP INTEGER
  xldv20pmThlFeUnavailableSeconds INTEGER
  xldv20pmThlFeUnavailableSecondsPLCP INTEGER
  xldv20pmThlDiscardedCells INTEGER
  xldv20pmThlImaGroupUnavailSecs INTEGER
  xldv20pmThlImaGroupNeNumFailures INTEGER
  xldv20pmThlImaLinkImaViolations INTEGER
  xldv20pmThlImaLinkOifAnomalies INTEGER
  xldv20pmThlImaLinkNeSevErroredSecs INTEGER
  xldv20pmThlImaLinkFeSevErroredSecs INTEGER
  xldv20pmThlImaLinkNeUnavailSecs INTEGER
  xldv20pmThlImaLinkFeUnavailSecs INTEGER
  xldv20pmThlImaLinkNeTxUnusableSecs INTEGER
  xldv20pmThlImaLinkNeRxUnusableSecs INTEGER
  xldv20pmThlImaLinkFeTxUnusableSecs INTEGER
  xldv20pmThlImaLinkFeRxUnusableSecs INTEGER
  xldv20pmThlImaLinkNeTxNumFailures INTEGER
  xldv20pmThlImaLinkNeRxNumFailures INTEGER

Xldv20pmAtmThresholdLimitEntry  
SEQUENCE    
  xldv20pmAtlThresholdLimitIndex INTEGER
  xldv20pmAtlTransmittedUserCells Unsigned32
  xldv20pmAtlLostUserCells Unsigned32
  xldv20pmAtlMisinsertedUserCells Unsigned32

Defined Values

xldv20Pm 1.3.6.1.4.1.231.7.1.2.1.1.5
OBJECT IDENTIFIER    

xldv20pmPerformanceManagementControl 1.3.6.1.4.1.231.7.1.2.1.1.5.1
OBJECT IDENTIFIER    

xldv20pmPerformanceMonitoring 1.3.6.1.4.1.231.7.1.2.1.1.5.2
OBJECT IDENTIFIER    

xldv20pmProtocolMonitoring 1.3.6.1.4.1.231.7.1.2.1.1.5.3
OBJECT IDENTIFIER    

xldv20pmThresholding 1.3.6.1.4.1.231.7.1.2.1.1.5.4
OBJECT IDENTIFIER    

xldv20pmTraps 1.3.6.1.4.1.231.7.1.2.1.1.5.5
OBJECT IDENTIFIER    

xldv20pmControl 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1
OBJECT IDENTIFIER    

xldv20pmCoIfIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.1
This attribute provides the interface index of the PM object for which PM parameters are configured .
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned16  

xldv20pmCoNrHistEntriesSize 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.2
This attribute is used to set the number of 15 minutes history entries which should be stored for history collection. Default value is 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmCoIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.3
This attribute identifies whether a 15 minutes interval or a day interval is selected in case of a resetIndividCurrent command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmCoControlReq 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.4
This attribute identifies a control command given by the SNMP agent. A reset for any individual PM object is possible via command resetIndividCurrent. The command setNrHistEntriesSize is used to set the number of 15 minutes history entries for history collection at a particular interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmControlReq  

xldv20pmCoControlStatus 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.5
The status of a control request.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20ControlStatus  

xldv20pmCoRemainingHistoryEntriesSize 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.6
This attribute indicates the number of remaining history entries which are available for the 15 minutes history collection wthin the ONU. PM on physical and ATM layer use the same history memory which is limited in total to 2000 entries. The manager can read this attribute after the execution of the setNrHistEntriesSize command .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2000  

xldv20pmCoOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.7
This attribute selects the OAM level f1 (1), f2 (2), f3 (3) .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmCoControlReqResult 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.8
The result of the last user command.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmControlReq  

xldv20pmCoControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.9
The time stamp of the last command (end of command).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

xldv20pmAtmControl 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2
OBJECT IDENTIFIER    

xldv20pmAcoIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.1
This attribute provides the index of the AtmPm object for which PM parameters shall be configured .
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned16  

xldv20pmAcoNrHistEntriesSize 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.2
This attribute is used to set the number of 15 minutes history entries which should be stored for history collection. The set HistEntrySize value is found in the xldv20pmAcHistEntrySize.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmAcoIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.3
This attribute identifies whether a 15 minutes interval or a day interval is selected in case of a resetIndividCurrent command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmAcoControlReq 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.4
This attribute identifies a control command given by the SNMP agent. A reset for any individual PM object is possible via command resetIndividCurrent. The command setNrHistEntriesSize is used to set the number of 15 minutes history entries for history collection at a particular interface. The commands create/delete are used to create/delete AtmPm monitoring objectes (entry in table xldv20pmAtmObjectsTable). The commands addEndpoint/deleteEndpoint are used to add or delete AtmPm endpoints to/from an PMo monitoring object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmControlReq  

xldv20pmAcoControlStatus 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.5
The status of a control request.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20ControlStatus  

xldv20pmAcoRemainingHistoryEntriesSize 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.6
This attribute indicates the number of remaining history entries which are available for the 15 minutes history collection within the ONU. PM on physical and ATM layer use the same history memory which is limited in total to 2000 entries. Commonly used by PM on physical and ATM layer The manager can read this attribute after the execution of the setNrHistEntriesSize command .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2000  

xldv20pmAcoFlowType 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.7
This attribute identifies the flow type : F4 (VP) or F5 (VC) segment or endToEnd flow.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmFlowType  

xldv20pmAcoFlowDirection 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.8
The flow direction of OAM cells. 'inwards' means flow direction from outside (external interface) to cross connection. 'outwards' means flow direction from inside to external interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20FlowDirection  

xldv20pmAcoConnectionIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.9
This attribute identifies the index of a Vpl or Vcl cross connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2048  

xldv20pmAcoConnectionIndexType 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.10
This attribute identifies the type of connection index and the termination point. It is in case of vplUni/vplNni : index of Vpl CC (xldv20AccVpiNniIndex) vclUni/vplNni : index of Vcl CC (xldv20VcxIndex).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmConnectionIndexType  

xldv20pmAcoRole 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.12
The role of endpoint. 'analyseWithBackwardReporting' (sink) means extracting forward monitoring (FM) OAM cells, sending back backward reporting OAM cells and no data collection for current and history table. 'analyseWithoutBackwardReporting' (sink) means extracting FM cells without any other OAM handling and also collecting data. 'generateWithCollect' (source) means inserting FM cells, extracting backward reporting cells if they arrive and collect data for current and history table. 'generateWithoutCollect' (source) means inserting FM cells but without collecting data. The CMU, the Ethernet part of the Twin NT s capable of operating as inserting or extracting point.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmRoleType  

xldv20pmAcoEndpointType 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.13
Identifies the type of endpoint.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmEndpointType  

xldv20pmAcoControlReqResult 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.14
The result of the last user command.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmControlReq  

xldv20pmAcoControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.15
The time stamp of the last command (end of command).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

xldv20pmCommonCurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2
This table contains the entries for the current 15 minute interval or the current day of PMo objects of the common group. (adc, adr, e3n and e3f) .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmCommonCurrentEntry

xldv20pmCommonCurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1
An entry describing the Common Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmCommonCurrentEntry  

xldv20pmCcIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.1
This attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmCcOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmCcAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.3
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmCcSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmCcHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.5
The number of 15min history entries configured at the particular interface. This attribute is used for history data collection. The default value is 1 and means at least one history entry is desired .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmCcNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.6
This read-only attribute indicates how many HistEntries are already available. The range of values is between 0 and xldv20pmCcHistEntrySize, thereby 0 means that this entry is not valid .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmCcElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.7
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmCcThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.8
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmCcNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.9
A near end counter of Errored Seconds (ES) over a 15 min/day interval. Counter appearence depends on interface type and OAM level : - adc, e3n: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.10
A far end counter of Errored Seconds (ES) over a 15 min /day interval. Counter appearence depends on interface type and OAM level : - adr, e3f: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.11
Represents a near end counter of Severely Errored Seconds (SES) over a 15 min /day interval. Counter appearence depends on interface type and OAM level : - adc, e3n: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.12
This read-only attribute represents a far end counter of Severely Errored Seconds (SES) over a 15 min /day interval. Counter appearence depends on interface type and OAM level : - adr, e3f: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcNeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.13
This read-only attribute represents a near end counter for Background Block Errors (BBE) over a 15 min /day interval. Counter appearence depends on interface type and OAM level : - adc, e3n: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcFeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.14
This read-only attribute represents a far end counter for Background Block Errors (BBE) over a 15 min /day interval. Counter appearence depends on interface type and OAM level : - adr, e3f: valid for F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.15
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : adc, e3n and f3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCcFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.16
This read-only attribute represents a far end counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : adr, e3f and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmCommonHistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3
This table contains the entries for the PMo objects of the 15 min /one day-history data collection results at the respective adc, adr drop area interfaces .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmCommonHistoryEntry

xldv20pmCommonHistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1
An entry describing the Common History Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmCommonHistoryEntry  

xldv20pmChIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmChOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmChHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.3
This attribute is an index used to address the PM history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmCcHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmChSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.4
Will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmChPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.5
Date/time at the end of the selected interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmChNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.6
This read-only attribute represents a near end counter of Errored Seconds (ES) over a 15 min /day interval. Counter applicable for : adc, e3n and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.7
This read-only attribute represents a far end counter of Errored Seconds (ES) within the current 15 minute interval or current day. Counter applicable for : adr, e3f and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.8
This read-only attribute represents a near end counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day. Counter applicable for : adc, e3n and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.9
This read-only attribute represents a far end counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day. Counter applicable for : adr, e3f and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChNeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.10
This read-only attribute represents a near end counter for Background Block Errors (BBE) over a 15 min /day interval. Counter applicable for : adc, e3n and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChFeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.11
This read-only attribute represents a far end counter for Background Block Errors (BBE) over a 15 min /day interval. Counter applicable for : adr, e3n and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.12
This read-only attribute represents a near end counter of Unavailable Seconds (UAS) for a 15 min /day interval. Counter applicable for : adc, e3n and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmChFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.13
This read-only attribute represents a far end counter of Unavailable Seconds (UAS) for a 15 min /day interval. Counter applicable for : adr, e3f and F3 level .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3CurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4
This table contains the entries for the current 15 minute interval or the current day for STS3c near-end and far-end PPTPs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmS3CurrentEntry

xldv20pmS3CurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1
An entry describing the STS3 near-end and far-end Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmS3CurrentEntry  

xldv20pmS3cIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmS3cOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmS3cAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.3
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmS3cSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmS3cHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.5
This read-only attribute indicates the number of 15min history entries configured at the particular interface. The default value is 1 and means that at least one history entry is provided .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmS3cNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.6
This read-only attribute indicates how many history entries are already available. The range of values is between 0 and xldv20S3cHistEntrySize, thereby 0 means that this entry is not valid .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmS3cElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.7
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmS3cThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.8
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used The range of values is [1,30].
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmS3cNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.9
This read-only attribute represents a counter of Errored Seconds (ES) within the current 15min interval or current day. Counter applicable for : s3n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.10
This read-only attribute represents a counter of Errored Seconds (ES) within the current 15min interval or current day. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.11
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15min interval or current day. Counter applicable for : s3n and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.12
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15min interval or current day. Counter applicable for : s3f and for F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cNeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.13
This read-only attribute represents a counter of Code Violations Errors within the current 15min interval or current day. Counter applicable for : s3n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cFeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.14
This read-only attribute represents a counter of Code Violations Errors within the current 15min interval or current day. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.15
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15min interval or current day. Counter applicable for : s3n and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.16
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15min interval or current day. Counter applicable for : s3f and level F2 and F3 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3cNeSeverelyErroredFrameSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.17
This read-only attribute represents a counter of Severely Errored Frame Seconds within the current 15min interval or current day. Counter applicable for : s3n and F1 level only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3HistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5
This table contains the entries for the PMo history objects at the near-end and far-end STS3c interfaces. It contains results that are overtaken from the s3CurrentTable PM-object at the end of a 15 min /day interval .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmS3HistoryEntry

xldv20pmS3HistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1
An entry describing the STS3 near-end and far-end History Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmS3HistoryEntry  

xldv20pmS3hIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmS3hOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmS3hHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.3
This attribute is used as index to address the history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20S3cHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmS3hSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmS3hPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.5
This read-only attribute is a record of date/time at the end of an interval .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmS3hNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.6
This read-only attribute represents a set of history counter for Errored Seconds (ES) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.7
This read-only attribute represents a set of history counter for Errored Seconds (ES) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.8
This read-only attribute represents a set of history counter for Severely Errored Seconds (SES) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3n and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.9
This read-only attribute represents a set of history counter for Severely Errored Seconds (SES) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hNeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.10
This read-only attribute represents a set of history counter for Code Violations Errors for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hFeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.11
This read-only attribute represents a set of history counter for Code Violations Errors for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.12
This read-only attribute represents a set of history counter for Unavailable Seconds (UAS) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3n and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.13
This read-only attribute represents a set of history counter for Unavailable Seconds (UAS) for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS3hNeSeverelyErroredFrameSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.14
This read-only attribute represents a set of history counter for Severely Errored Frame Seconds for the passed up to 96 periods of 15 minutes and the passed day interval. Counter applicable for : s3n and F1 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3CurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6
This table contains the entries for the current 15 minute interval or the current day for DS3 near-end and far-end PPTPs. Note: Day PM collection uses the 15min interval results .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmD3CurrentEntry

xldv20pmD3CurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1
An entry describing the DS3 near-end and far-end Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmD3CurrentEntry  

xldv20pmD3cIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmD3cOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmD3cAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.3
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmD3cSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmD3cHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.5
This read-only attribute indicates the configured history size. The default value is 1 and means that at least one history entry is provided.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmD3cNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.6
This read-only attribute indicates how many history entries are already available. The range of values is between 0 and xldv20pmD3cHistEntrySize, thereby 0 means that this entry is not valid .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmD3cElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.7
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmD3cThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.8
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used. These default values are not part of the threshold limit table but are hard coded in the application SW of PM. The range of values is [1,30].
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmD3cNeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.9
This read-only attribute represents a counter of Errored Seconds (ES) within the current interval or current day, the generation thereof is based on CP-bit parity. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.10
This read-only attribute represents a counter of Errored Seconds (ES) within the current 15 minute interval or current day, the generation thereof is based on CP-bit parity . Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.11
This read-only attribute represents a counter of Errored Seconds on PLCP-bit parity within the current 15 minute interval or current day. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.12
This read-only attribute represents a counter of Errored Seconds on PLCP-bit parity within the current 15 minute interval or current day. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.13
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day based on CP-bit parity, the generation thereof is based on CP-bit parity. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.14
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day, the generation thereof is based on CP-bit parity . Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.15
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day, the generation thereof is based on PLCP-bit parity . Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.16
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day, the generation thereof is based on PLCP-bit parity . Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeCodeViolationsP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.17
This read-only attribute represents a counter of Code Violations Errors (Count of P-bit parity errors) within the current 15 minute interval or current day. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.18
This read-only attribute represents a counter of Code Violations Errors (Count of CP-bit parity errors) within the current 15 minute interval or current day. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.19
This read-only attribute represents a counter of Code Violations Errors (Count of CP-bit parity errors) within the current 15 minute interval or current day. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.20
This read-only attribute represents a counter of Code Violations Errors (Count of PLCP frame Bit Interleaved Parity errors) within the current 15 minute interval or current day. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.21
This read-only attribute represents a counter of Code Violations Errors (Count of PLCP frame Bit Interleaved Parity errors) within the current 15 minute interval or current day. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.22
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : d3n and F2 level only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.23
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.24
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. The generation is based on PLCP-bit parity. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.25
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. The generation is based on PLCP-bit parity. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cNeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.26
This read-only attribute represents a counter of one second intervals containing one ore more Severely Errored Frame (SEF) defects or one or more Alarm Indication Signal (AIS) defects within the current 15 minute interval or current day. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3cFeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.27
This read-only attribute represents a counter of one second intervals containing one ore more Severely Errored Frame (SEF) defects or one or more Alarm Indication Signal (AIS) defects within the current 15 minute interval or current day. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3HistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7
This table contains the entries for the PMo history objects at the near-end and far-end DS3 interfaces. It contains results that are overtaken from the D3CurrentTable PM-object at the end of a 15 min /day interval .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmD3HistoryEntry

xldv20pmD3HistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1
An entry describing the DS3 near-end and far-end History Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmD3HistoryEntry  

xldv20pmD3hIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmD3hOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmD3hHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.3
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmD3cHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmD3hSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmD3hPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.5
This read-only attribute is a record of date/time at the end of an interval .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmD3hNeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.6
This read-only attribute represents a set of history counter of Errored Seconds (ES), the generation thereof is based on CP-bit parity for a 15min /day interval. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.7
This read-only attribute represents a set of history counter of Errored Seconds (ES), the generation thereof is based on CP-bit parity for a 15min /day interval. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.8
This read-only attribute represents a set of history counter of Errored Seconds (ES) (One second interval in which Code Violations errors occure) for a 15min /day interval. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.9
This read-only attribute represents a set of history counter of Errored Seconds (ES) (One second interval in which Code Violations errors occure) for a 15min /day interval. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.10
This read-only attribute represents a set of history counter of Severely Errored Seconds (ES), the generation thereof is based on CP-bit parity for a 15min /day interval. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.11
This read-only attribute represents a set of history counter of Severely Errored Seconds (ES), the generation thereof is based on CP-bit parity for a 15min /day interval. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.12
This read-only attribute represents a set of history counter of Severely Errored Seconds (SES) for a 15min / day interval. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.13
This read-only attribute represents a set of history counter of Severely Errored Seconds (SES) for a 15min / day interval. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeCodeViolationsP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.14
This read-only attribute represents a counter of Code Violations Errors (Count of P-bit parity errors) for a 15 min /day interval. Counter applicable for : d3n and F2 level only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.15
This read-only attribute represents a set of history counter of Code Violations Errors (Count of CP-bit parity errors) for a 15min /day interval. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.16
This read-only attribute represents a set of history counter of Code Violations Errors (Count of CP-bit parity errors) for a 15min /day interval. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.17
This read-only attribute represents a set of history counter of Code Violations Errors (Count of PLCP frame Bit Interleaved Parity errors) for a 15min /day interval. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.18
This read-only attribute represents a set of history counter of Code Violations Errors (Count of PLCP frame Bit Interleaved Parity errors) for a 15min /day interval. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.19
This read-only attribute represents a set of history counter of Unavailable Seconds (UAS) for a 15min /day interval. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.20
This read-only attribute represents a set of history counter of Unavailable Seconds (UAS) for a 15min /day interval. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.21
This read-only attribute represents a set of history counter of Unavailable Seconds (UAS) for a 15min /day interval. Counter applicable for : d3n and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.22
This read-only attribute represents a set of history counter of Unavailable Seconds (UAS) for a 15min /day interval. Counter applicable for : d3f and F3 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hNeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.23
This read-only attribute represents a set of history counter of one second intervals containing one ore more Severely Errored Frame (SEF) defects or one or more Alarm Indication Signal (AIS) defects for a 15min /day interval. Counter applicable for : d3n and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmD3hFeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.24
This read-only attribute represents a set of history counter of one second intervals containing one ore more Severely Errored Frame (SEF) defects or one or more Alarm Indication Signal (AIS) defects for a 15min /day interval. Counter applicable for : d3f and F2 level only .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1CurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8
This table contains the entries for the current 15 minute interval or the current day for STM1 near-end and far-end PPTPs. Note: Day PM collection uses the 15min interval results .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmS1CurrentEntry

xldv20pmS1CurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1
An entry describing the Stm1 Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmS1CurrentEntry  

xldv20pmS1cIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmS1cOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmS1cAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.3
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmS1cSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmS1cHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.5
This read-only attribute indicates the configured history size. The default value is 1 and means that at least one history entry is provided.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmS1cNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.6
This read-only attribute indicates how many history entries are already available. The range of values is between 0 and xldv20pmS1cHistEntrySize, thereby 0 means that this entry is not valid .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmS1cElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.7
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmS1cThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.8
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used. These default values are not part of the threshold limit table but are hard coded in the application SW of PM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmS1cNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.9
This read-only attribute represents a counter of Errored Seconds (ES) within the current 15 minute interval or current day. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.10
This read-only attribute represents a counter of Errored Seconds (ES) within the current 15 minute interval or current day. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.11
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.12
This read-only attribute represents a counter of Severely Errored Seconds (SES) within the current 15 minute interval or current day. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.13
This read-only attribute represents a counter for Background Block Errors (BBE) within the current 15 minute interval or current day. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cFeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.14
This read-only attribute represents a counter for Background Block Errors (BBE) within the current 15 minute interval or current day. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.15
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.16
This read-only attribute represents a counter of Unavailable Seconds (UAS) within the current 15 minute interval or current day. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeOfsSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.17
This read-only attribute represents a counter of Errored Seconds on defect OFS within the current 15 minute interval or current day. Counter applicable for : s1n and level F1 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeAisSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.18
This read-only attribute represents a counter of errored Seconds on defect alarm indicatin signal AIS for a 15 min /day interval. Counter applicable for : s1n and F2 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1cNeLosSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.19
This read-only attribute represents a counter of errored Seconds on defect LOS within the current 15 minute interval or current day. Counter applicable for : s1n and level F1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1HistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9
This table contains the entries for the PMo objects of the 15 min /one day-history data collection results at the respective stm1 (s1n, s1f) drop area interfaces .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmS1HistoryEntry

xldv20pmS1HistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1
An entry describing the S1 History Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmS1HistoryEntry  

xldv20pmS1hIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmS1hOAMLevel 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.2
This attribute is used to select between the 3 OAM levels f1 (1), f2 (2) and f3 (3) .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

xldv20pmS1hHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.3
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmCcHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmS1hSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.4
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmS1hPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.5
Date/time at the end of the selected interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmS1hNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.6
This read-only attribute represents a counter of Errored Seconds (ES) over a 15 min /day interval. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.7
This read-only attribute represents a counter of Errored Seconds (ES) over a 15 min /day interval. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.8
This read-only attribute represents a counter of Severely Errored Seconds (SES) over a 15 min /day interval. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.9
This read-only attribute represents a counter of Severely Errored Seconds (SES) over a 15 min /day interval. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.10
This read-only attribute represents a counter for Background Block Errors (BBE) over a 15 min /day interval. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hFeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.11
This read-only attribute represents a counter for Background Block Errors (BBE) over a 15 min /day interval. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.12
This read-only attribute represents a counter of Unavailable Seconds (UAS) for a 15 min /day interval. Counter applicable for : s1n and F1, F2, F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.13
This read-only attribute represents a counter of Unavailable Seconds (UAS) for a 15 min /day interval. Counter applicable for : s1f and F2 and F3 levels .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeOfsSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.14
This read-only attribute represents a counter of Errored Seconds on defect OFS for a 15 min /day interval. Counter applicable for : s1n and level F1 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeAisSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.15
This read-only attribute represents a counter of errored Seconds on defect alarm indicatin signal AIS for a 15 min /day interval. Counter applicable for : s1n and level F2 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmS1hNeLosSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.16
This read-only attribute represents a counter of errored Seconds on defect LOS for a 15 min /day interval. Counter applicable for : s1n and F1 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAtmObjectsTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10
This table contains the entries for the PMo objects on ATM layer. Maximum of monitored connections is 128.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmAtmObjectsEntry

xldv20pmAtmObjectsEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1
An entry of the xldv20pmAtmObjectsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmObjectsEntry  

xldv20pmAoIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.1
Identifies an entry of the xldv20pmAtmObjectsTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

xldv20pmAoFlowType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.2
This attribute identifies the flow type : F4 (VP) or F5 (VC) segment or endToEnd flow.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmFlowType  

xldv20pmAoAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.3
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmAoBlockSize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.4
This is the number of user cells after which PMo cell is inserted. Default is 128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20pmBlockSizeType  

xldv20pmAtmEndpointsTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11
This table contains the enpoints for PMo on Atm layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmAtmEndpointsEntry

xldv20pmAtmEndpointsEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1
An entry of xldv20pmAtmEndpointsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmEndpointsEntry  

xldv20pmAeEndpointType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.1
Identifies the type of endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmEndpointType  

xldv20pmAeConnectionIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.2
This attribute identifies the Vpl or Vcl cross connection where an endpoint object should be added.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2048  

xldv20pmAeConnectionIndexType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.3
This attribute identifies the type of connection index and the termination point where an endpoint should be added.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmConnectionIndexType  

xldv20pmAeRole 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.4
The role of endpoint. 'analyseWithBackwardReporting' (sink) means extracting forward monitoring (FM) OAM cells, sending back backward reporting OAM cells and no data collection for current and history table. 'analyseWithoutBackwardReporting' (sink) means extracting FM cells and also collecting data. 'generateWithCollect' (source) means inserting FM cells, extracting backward reporting cells if they arrive and collect data for current and history table. 'generateWithoutCollect' (source) means inserting FM cells but without collecting data. The CMU, the Ethernet part of the Twin NT can be inserting and extracting points.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmRoleType  

xldv20pmAeFlowDirection 1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.5
This attribute identifies the flow direction. inwards means flow direction from outside (external interface) to cross connection. outwards means flow direction from inside to external interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20FlowDirection  

xldv20pmAtmCurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12
This table contains the entries for the the PMo objects for the current data of Pmo monitoring objects on ATM layer. It includes attributes for performance parameters, collection interval is 15 minutes and one day .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmAtmCurrentEntry

xldv20pmAtmCurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1
An entry describing the Atm Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmCurrentEntry  

xldv20pmAcIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmAcAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.2
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmAcSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmAcHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.4
This is the configured size of history.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmAcNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.5
This is the number of history entries which are available in the history table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmAcElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.6
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmAcThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.7
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmAcTransmittedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.8
This read-only attribute represents a counter of transmitted user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAcLostUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.9
This read-only attribute represents a counter of lost user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAcMisinsertedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.10
This read-only attribute represents a counter of Misinserted user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAtmHistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13
This table contains the entries for the 15 min /one day-history data collection results for PMo objects of ATM layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmAtmHistoryEntry

xldv20pmAtmHistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1
An entry describing the History Data Table for PMo on ATM layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmHistoryEntry  

xldv20pmAhIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmAhHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.2
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmAcHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmAhSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmAhPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.4
Date/time at the end of the selected interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmAhTransmittedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.5
This read-only attribute represents a counter of transmitted user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAhLostUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.6
This read-only attribute represents a counter of lost user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmAhMisinsertedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.7
This read-only attribute represents a counter of Misinserted user cells for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmImaGroupCurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14
This table contains the entries for the PMo objects for the current data of Pmo monitoring objects for IMA groups . Collection interval is the current 15 minute and one the current day .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmImaGroupCurrentEntry

xldv20pmImaGroupCurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1
An entry describing the current PMo data for ImaGroups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmImaGroupCurrentEntry  

xldv20pmImaGroupCurrentIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmImaGroupCurrentAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.2
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmImaGroupCurrentSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmImaGroupCurrentHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.4
This is the configured size of history.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmImaGroupCurrentNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.5
This is the number of history entries which are available in the history table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmImaGroupCurrentElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.6
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmImaGroupCurrentThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.7
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmImaGroupCurrentUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.8
The counts of second intervals where the IMA group traffic state machine is down in the current for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaGroupCurrentNeNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.9
The number of times a near-end group failure (config-Aborted, unsufficient-Links) has been reported for a 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaGroupHistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15
This table contains the entries for the 15 min /one day-history data collection results for PMo objects of IMA Group interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmImaGroupHistoryEntry

xldv20pmImaGroupHistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1
An entry describing the History Data Table for PMo IMA groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmImaGroupHistoryEntry  

xldv20pmImaGroupHistoryIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmImaGroupHistoryHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.2
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmImaGroupCurrentHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmImaGroupHistorySuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmImaGroupHistoryPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.4
Date/time at the end of the selected interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmImaGroupHistoryUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.5
The counts of second intervals where the IMA group traffic state machine is down in the current 15 min /day interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaGroupHistoryNeNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.6
The number of times a near-end group failure (config-Aborted, unsufficient-Links) has been reported for a previous 15 min interval or the previous day.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16
This table contains the entries for the the PMo objects for the current data of Pmo monitoring objects for IMA groups . It includes attributes for performance parameters, collection interval is 15 minutes and one day .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmImaLinkCurrentEntry

xldv20pmImaLinkCurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1
An entry describing the current PMo data for ImaLinks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmImaLinkCurrentEntry  

xldv20pmImaLinkCurrentIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmImaLinkCurrentAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.2
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmImaLinkCurrentSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmImaLinkCurrentHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.4
This is the configured size of history.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmImaLinkCurrentNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.5
This is the number of history entries which are available in the history table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmImaLinkCurrentElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.6
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmImaLinkCurrentThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.7
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmImaLinkCurrentImaViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.8
ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions, in the current 15 minute interval. ATM Forum IMA v1.1, (R-125) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentOifAnomalies 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.9
The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end in the current 15 minute interval. This is an optional attribute. ATM Forum IMA v1.1, (O-20) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.10
Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition, in the current 15 minute interval. ATM Forum IMA v1.1, (R-126) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentFeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.11
Count of unavailable seconds at near-end in the current 15 minute interval: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. ATM Forum IMA v1.1, (R-128) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.12
Count of unavailable seconds at near-end in the current 15 minute interval: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2 on page 77 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentFeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.13
Count of unavailable seconds at far-end in the current 15 minute interval: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2 on page 77 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.14
Tx Unusable seconds: count of Unusable seconds at the near-end Tx LSM in the current 15 minute interval. ATM Forum IMA v1.1, (R-130) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.15
Rx Unusable seconds: count of Unusable seconds at the near-end Rx LSM in the current 15 minute interval. ATM Forum IMA v1.1, (R-131) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentFeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.16
Tx Unusable seconds: count of Unusable seconds at the far-end Tx LSM in the current 15 minute interval. ATM Forum IMA v1.1, (R-132) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentFeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.17
Rx Unusable seconds: count of Unusable seconds at the far-end Rx LSM in the current 15 minute interval. ATM Forum IMA v1.1, (R-133) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeTxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.18
The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault) in the current 15 minute interval. ATM Forum IMA v1.1, (R-134) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkCurrentNeRxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.19
The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected, or some form of implementation specific receive fault) in the current 15 minute interval. ATM Forum IMA v1.1, (R-135) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17
This table contains the entries for the 15 min /one day-history data collection results for PMo objects of IMA Link interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmImaLinkHistoryEntry

xldv20pmImaLinkHistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1
An entry describing the History Data Table for PMo IMA groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmImaLinkHistoryEntry  

xldv20pmImaLinkHistoryIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmImaLinkHistoryHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.2
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmImaLinkCurrentHistEntrySize .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmImaLinkHistorySuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmImaLinkHistoryPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.4
Date/time at the end of the selected interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmImaLinkHistoryImaViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.5
ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions, in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-125) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryOifAnomalies 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.6
The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end in one of the previous 96, individual 15 minute, intervals or the previous day. This is an optional attribute. ATM Forum IMA v1.1, (O-20) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.7
Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition, in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-126) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryFeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.8
Count of unavailable seconds at near-end in one of the previous 96, individual 15 minute, intervals or the previous day. Unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. ATM Forum IMA v1.1, (R-127) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.9
Count of unavailable seconds at near-end in one of the previous 96, individual 15 minute, intervals or the previous day. Unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. ATM Forum IMA v1.1, (R-128) and (O-26) in Section 12.2.2.2 on page 77 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryFeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.10
Count of unavailable seconds at far-end in one of the previous 96, individual 15 minute, intervals or the previous day. Unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2 on page 77 .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.11
Tx Unusable seconds: count of Unusable seconds at the near-end Tx LSM in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-130) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.12
Rx Unusable seconds: count of Unusable seconds at the near-end Rx LSM in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-131) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryFeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.13
Tx Unusable seconds: count of Unusable seconds at the far-end Tx LSM in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-132) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryFeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.14
Rx Unusable seconds: count of Unusable seconds at the far-end Rx LSM in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-133) and (O-26) in Section 12.2.2.2 on page 77.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeTxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.15
The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault) in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-134) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmImaLinkHistoryNeRxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.16
The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected, or some form of implementation specific receive fault) in one of the previous 96, individual 15 minute, intervals or the previous day. ATM Forum IMA v1.1, (R-135) and (O-26) in Section 12.2.2.2 on page 77
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

xldv20pmTcaPrMCurrentTable 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1
This table contains the entries for the PrM object at the following tca layer locations: - STM1 interface (in downstream direction) - STS3-c interface (in downstream direction) - E3 interface (in downstream direction) - DS3 interface (in downstream direction) - SU_AD16 interfaces (in upstream stream direction). PrM also possible at IMA groups. It includes attributes for performance parameters, collection interval is 15 min /one day .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmTcaPrMCurrentEntry

xldv20pmTcaPrMCurrentEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1
An entry describing the TC-Adaptor Current Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmTcaPrMCurrentEntry  

xldv20pmTcIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.1
This nac type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmTcAdminState 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.2
This read-write attribute is used to activate (unlock) and deactivate (lock) the functions (incl. collection) performed by this managed entity. Note: the 15min collection object must be activated, before day collection can operate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Xldv20AdminState  

xldv20pmTcSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmTcHistEntrySize 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.4
This read-only attribute indicates the number of 15min history entries configured for the particular interface. The default value is 1 and means that at least one history entry is provided.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmTcNrHistEntriesAvailable 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.5
This read-only attribute indicates how many HistEntries are already available. The range of values is between 0 and xldv20pmTcHistEntrySize, thereby 0 means that this entry is not valid .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..96  

xldv20pmTcElapsedTime 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.6
This read-only attribute represents the difference between the current time and the start of the present summary interval. Units are seconds when 15 minute interval is selected or minutes for day interval. (Note: accurate to the sample time interval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1440  

xldv20pmTcThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.7
This read-write attribute provides an index to the ThresholdLimitTable managed entity that contains the threshold limits for the performance parameters reported by this managed entity. When the value of this attribute is set to 1, default threshold limits shall be used. These default values are not part of the threshold limit table but are hard coded in the application SW of PM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmTcDiscardedCells 1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.8
This read-only attribute represents a counter of the number of ATM cells discarded at this interface, due to a HEC violation, since the start of this interval .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmTcaPrMHistoryTable 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2
This table contains the entries for the PrM history object at the different tca layer locations. It contains results that are overtaken from the TcaPrMCurrentTable PM-object at the end of a 15 min /day interval .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmTcaPrMHistoryEntry

xldv20pmTcaPrMHistoryEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1
An entry describing the TC-Adaptor History Data Table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmTcaPrMHistoryEntry  

xldv20pmThIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.1
This type attribute is used to select between the 15 min or the day accumulation types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmThHistEntryNr 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.2
This attribute is used as index to address a history entry. Entry 1 is the most recent, entry 96 is 24 hours ago. The range of values is between 1 and xldv20pmTcHistEntrySize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..96  

xldv20pmThSuspectFlag 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.3
This read-only attribute will be set to indicate that troubles arose during an interval and that the counter values are suspect and incomplete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Xldv20pmSuspectType  

xldv20pmThPeriodEndTime 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.4
This read-only attribute is a record of date/time at the end of an interval .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThDiscardedCells 1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.5
This read-only attribute represents a set of history counter of the number of ATM cells discarded at this interface, due to a HEC violation, since the start of this interval .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

xldv20pmThresholdLimitTable 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1
The threshold limit table for all interface. This table associates threshold limit index/PM counter pairs with threshold limit values for a 15 minutes interval. Entries with same threshold limit index belong to the same threshold limit profile. Each of the following TC-adaptor types are available and can be configured: adc, s1n, s3n, d3n, e3n. A crossing of a threshold limit leads to a threshold crossing alert.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmThresholdLimitEntry

xldv20pmThresholdLimitEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1
An entry describing the threshold limit information .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmThresholdLimitEntry  

xldv20pmThlThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.1
This read-only attribute selects a profile out of the threshold limit table .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmThlNeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.2
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlNeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.3
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlNeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.4
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlNeCodeViolationsP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.5
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlNeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.6
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlNeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.7
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.8
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.9
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.10
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeSeverelyErroredFrameSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.11
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.12
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.13
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.14
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.15
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.16
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeAisSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.17
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeOfsSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.18
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlNeLosSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.19
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeBackgroundBlockErrors 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.20
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlFeCodeViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.21
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlFeCodeViolationsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.22
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlFeCodeViolationsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.23
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlFeErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.24
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.25
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.26
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeSas 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.27
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeSeverelyErroredSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.28
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeSeverelyErroredSecondsCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.29
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeSeverelyErroredSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.30
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeUnavailableSeconds 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.31
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlFeUnavailableSecondsPLCP 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.32
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

xldv20pmThlDiscardedCells 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.33
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaGroupUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.34
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaGroupNeNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.35
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkImaViolations 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.36
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkOifAnomalies 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.37
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.38
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkFeSevErroredSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.39
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.40
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkFeUnavailSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.41
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.42
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.43
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkFeTxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.44
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkFeRxUnusableSecs 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.45
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeTxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.46
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmThlImaLinkNeRxNumFailures 1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.47
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xldv20pmAtmThresholdLimitTable 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2
The threshold limit table for all interface. This table associates threshold limit index/PM counter pairs with threshold limit values for a 15 minutes interval. Entries with same threshold limit index belong to the same threshold limit profile. A crossing of a threshold limit leads to a threshold crossing alert.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xldv20pmAtmThresholdLimitEntry

xldv20pmAtmThresholdLimitEntry 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1
An entry describing the threshold limit information .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmThresholdLimitEntry  

xldv20pmAtlThresholdLimitIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.1
This read-only attribute selects a profile out of the threshold limit table of PM on ATM layer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

xldv20pmAtlTransmittedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.2
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32  

xldv20pmAtlLostUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.3
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32  

xldv20pmAtlMisinsertedUserCells 1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.4
This read-write attribute selects the threshold limit value of the counter in the current threshold limit profile.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32  

xldv20pmTrapVars 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1
OBJECT IDENTIFIER    

xldv20pmTvIfIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.1
The interface index of the reporting PM object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Unsigned16  

xldv20pmTvPmType 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.2
Specifies the reporting PM object and OAM level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmType  

xldv20pmTvPmCounter 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.3
Identifies the PM counter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmCounterName  

xldv20pmTvCurrentCounterValue 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.4
The actual counter value at detection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Counter  

xldv20pmTvCurrentCounterLimit 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.5
The current value of threshold limit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Counter  

xldv20pmTvAtmPmCounter 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.6
Identifies the performance parameter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmAtmCounterType  

xldv20pmTvAtmObjectIndex 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.7
Identifies the AtmPm object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Unsigned16  

xldv20pmTvEndpointType 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.8
Identifies the type of endpoint.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmEndpointType  

xldv20pmTvIntervalType 1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.9
Identifies the type of interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Xldv20pmIntervalType  

xldv20pmTrapTypes 1.3.6.1.4.1.231.7.1.2.1.1.5.5.2
OBJECT IDENTIFIER    

xldv20pmTrThresholdCrossingAlert 200
Threshold crossing alert for PM on physical layer.
TRAP-TYPE    

xldv20pmTrAtmThresholdCrossingAlert 300
Threshold crossing alert for PM on ATM layer .
TRAP-TYPE    

xldv20pmTrAtmObjectCreation 302
An Atm object is created.
TRAP-TYPE    

xldv20pmTrAtmObjectDeletion 303
An Atm object is deleted.
TRAP-TYPE    

xldv20pmTrAtmEndpointObjectCreation 304
An Atm endpoint object is created.
TRAP-TYPE    

xldv20pmTrAtmEndpointObjectDeletion 305
An Atm endpoint object is deleted.
TRAP-TYPE