XSWITCH-MIB

File: XSWITCH-MIB.mib (118411 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
GEN-MIB

Imported symbols

Counter TimeTicks IpAddress
OBJECT-TYPE DisplayString lannet

Defined Types

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

ScGenMonEntry  
SEQUENCE    
  scGenMonSwitchId INTEGER
  scGenMonDropEvents Counter
  scGenMonOctets Counter
  scGenMonPkts Counter
  scGenMonGoodBroadcastPkts Counter
  scGenMonGoodMulticastPkts Counter
  scGenMonGoodPkts Counter
  scGenMonBadPkts Counter
  scGenMonGoodOctets Counter
  scGenMonBadOctets Counter
  scGenMonSmonCapability OCTET STRING
  scGenMonMIBCtrMode INTEGER
  scGenMonSwitchVLANList OCTET STRING
  scGenMonMIBCtrList OCTET STRING
  scGenMonTimeStamp TimeTicks
  scGenMonVlanTimeStamp TimeTicks

ScGenMonPriorityEntry  
SEQUENCE    
  scGenMonPrioritySwitchId INTEGER
  scGenMonPriorityId INTEGER
  scGenMonPriorityGoodPkts Counter
  scGenMonPriorityGoodOctets Counter

ScGenMonVLANEntry  
SEQUENCE    
  scGenMonVLANSwitchId INTEGER
  scGenMonVLANId INTEGER
  scGenMonVLANGoodPkts Counter
  scGenMonVLANGoodOctets Counter
  scGenMonVLANStatsUcastPkts Counter
  scGenMonVLANStatsMcastPkts Counter
  scGenMonVLANStatsBcastPkts Counter

ScHostTimePortCorrEntry  
SEQUENCE    
  scHostTimeAddress OCTET STRING
  scHostTimeCreationOrder INTEGER 1..65535
  scHostTimeIndex INTEGER 1..65535
  scHostTimePortConnection INTEGER

ScGenGroupEntry  
SEQUENCE    
  scGenGroupId INTEGER
  scGenGroupUseSwitches INTEGER
  scGenGroupCopyPortSupport INTEGER
  scGenGroupXswitchConnection INTEGER
  scGenGroupStatus INTEGER
  scGenGroupSwitchType INTEGER
  scGenGroupNumberOfLoads INTEGER
  scGenGroupSetDefaults INTEGER
  scGenGroupSupportCopyPortList OCTET STRING
  scGenGroupSupportPortCountersList OCTET STRING
  scGenGroupSupportSegCountersList OCTET STRING
  scGenGroupUpLinkType INTEGER
  scGenGroupPlugInType INTEGER
  scGenGroupPlugInDescr DisplayString
  scGenGroupPlugInCS DisplayString
  scGenGroupDefaultVLAN INTEGER
  scGenGroupCascadingType INTEGER
  scGenGroupCascadingDescr DisplayString
  scGenGroupCascadingCS DisplayString
  scGenGroupSupportDstCopyPortList OCTET STRING
  scGenGroupBUPSType INTEGER
  scGenGroupBUPSCS DisplayString
  scGenGroupBUPSFansStatus INTEGER
  scGenGroupFansStatus INTEGER
  scGenGroupInternalBuffering INTEGER
  scGenGroupMcFilterBoxSupport INTEGER
  scGenGroupMcFilterPersonalitySupport INTEGER
  scGenGroupMcFilterStackingSupport INTEGER
  scGenGroupLACPMode INTEGER
  scGenGroupSecurityMode INTEGER
  scGenGroupBroadcastStormControl INTEGER
  scGenGroupBroadcastThreshold INTEGER
  scGenGroupPriorityQueuesScheduling INTEGER
  scGenGroupBoundedDelay INTEGER
  scGenGroupSLDAdminStatus INTEGER

ScGenGroupSmonEntry  
SEQUENCE    
  scGenGroupSmonGroupId INTEGER
  scGenGroupSmonCapability OCTET STRING
  scGenGroupSmonVlanList OCTET STRING
  scGenGroupSmonDropEvents Counter
  scGenGroupSmonGoodBroadcastPkts Counter
  scGenGroupSmonGoodMulticastPkts Counter
  scGenGroupSmonGoodPkts Counter
  scGenGroupSmonBadPkts Counter
  scGenGroupSmonGoodOctets Counter
  scGenGroupSmonBadOctets Counter
  scGenGroupSmonPkts Counter
  scGenGroupSmonOctets Counter
  scGenGroupSmonMIBCtrMode INTEGER

ScGenGroupVlanEntry  
SEQUENCE    
  scGenGroupVlanGroupId INTEGER
  scGenGroupVlanId INTEGER
  scGenGroupVlanUcastPkts Counter
  scGenGroupVlanMcastPkts Counter
  scGenGroupVlanBcastPkts Counter
  scGenGroupVlanGoodPkts Counter
  scGenGroupVlanGoodOctets Counter
  scGenGroupVlanUcastOctets Counter
  scGenGroupVlanMcastOctets Counter
  scGenGroupVlanBcastOctets Counter
  scGenGroupVlanCurrentEgressPorts OCTET STRING
  scGenGroupVlanCurrentUntaggedPorts OCTET STRING
  scGenGroupVlanStaticEgressPorts OCTET STRING
  scGenGroupVlanStaticUntaggedPorts OCTET STRING

ScGenGroupRspEntry  
SEQUENCE    
  scGenGroupRspGroupId INTEGER
  scGenGroupRspHelloInterval INTEGER
  scGenGroupRspDevicePollingInterval INTEGER
  scGenGroupRspDeviceNotRespondingTimeout INTEGER
  scGenGroupRspSwitchNotRespondingTimeout INTEGER
  scGenGroupRspMoveToForwardingInterval INTEGER
  scGenGroupRspBroadcastArpShortInterval INTEGER
  scGenGroupRspBroadcastArpShortIntervalNumber INTEGER
  scGenGroupRspBroadcastArpLongInterval INTEGER
  scGenGroupRspPeriodicPingsBoxIpAddress IpAddress
  scGenGroupRspPeriodicPingsDestinationIpAddress IpAddress
  scGenGroupRspMode INTEGER

ScGenPortEntry  
SEQUENCE    
  scGenPortGroupId INTEGER
  scGenPortId INTEGER
  scGenPortVLAN INTEGER
  scGenPortPriority INTEGER
  scGenPortSetDefaults INTEGER
  scGenPortBackbone INTEGER
  scGenPortCopyMode INTEGER
  scGenPortCopyDestination INTEGER
  scGenPortLinkAggregationNumber INTEGER
  scGenPortSendBridgedPackets INTEGER
  scGenPortVLANEgressStaticConfiguration OCTET STRING
  scGenPortStaticVLANBinding INTEGER
  scGenPortSecId INTEGER
  scGenPortMaxLagsOnSec INTEGER
  scGenPortGenericTrap INTEGER
  scGenPortLACPMode INTEGER
  scGenPortLastIntruderSourceAddr OCTET STRING
  scGenPortSecurityMode INTEGER
  scGenPortSTA INTEGER
  scGenPortLagCapability OCTET STRING
  scGenPortCapability OCTET STRING
  scGenPortSLDAdminStatus INTEGER
  scGenPortSLDStatus INTEGER

ScGenPortRspEntry  
SEQUENCE    
  scGenPortRspGroupId INTEGER
  scGenPortRspId INTEGER
  scGenPortRspMode INTEGER

ScGenSwitchEntry  
SEQUENCE    
  scGenSwitchId INTEGER
  scGenSwitchCopyMode INTEGER
  scGenSwitchCopySource INTEGER
  scGenSwitchCopyDestination INTEGER
  scGenSwitchSetDefaults INTEGER
  scGenSwitchVIDP INTEGER
  scGenSwitchType INTEGER
  scGenSwitchMasterId INTEGER
  scGenSwitchReset INTEGER
  scGenSwitchNumberOfLoads INTEGER
  scGenSwitchAgVLAN INTEGER
  scGenSwitchVLANList OCTET STRING
  scGenSwitchSTA INTEGER
  scGenSwitchSecurityMode INTEGER
  scGenSwitchFindQuery OCTET STRING
  scGenSwitchFindResult OCTET STRING
  scGenSwitchSWRdChange OCTET STRING
  scGenSwitchDefaultVLAN INTEGER
  scGenSwitchVLANBridging INTEGER
  scGenSwitchOldVersionModules DisplayString
  scGenSwitchVIDPNonSupportedModules DisplayString
  scGenSwitchSTANonSupportedModules DisplayString
  scGenSwitchIDSNonSupportedModules DisplayString
  scGenSwitchMcFilter INTEGER
  scGenSwitchMcFilterHostAgingTime INTEGER
  scGenSwitchMcFilterRouterAgingTime INTEGER
  scGenSwitchMcFilterDelayTime INTEGER
  scGenSwitchLACPMode INTEGER
  scGenSwitchSecurityModePermit INTEGER
  scGenSwitchFastAgingOnRemoteTopChg INTEGER
  scGenSwitchGigaMode INTEGER
  scGenSwitchCAMClear INTEGER

ScGenLinkAggregationEntry  
SEQUENCE    
  scGenLinkAggregationId INTEGER
  scGenLinkAggregationName DisplayString
  scGenLinkAggregationBasePortGroupId INTEGER
  scGenLinkAggregationBasePortId INTEGER
  scGenLinkAggregationNumberOfPorts INTEGER
  scGenLinkAggregationLogicalPortGroupId INTEGER
  scGenLinkAggregationLogicalPortId INTEGER
  scGenLinkAggregationFunctionalStatus INTEGER
  scGenLinkAggregationAutoNegResults INTEGER
  scGenLinkAggregationFaultMask OCTET STRING
  scGenLinkAggregationStatus RowStatus

ScGenPortIPAddressRspEntry  
SEQUENCE    
  scGenPortIPAddressRspGroupId INTEGER
  scGenPortIPAddressRspPortId INTEGER
  scGenPortIPAddressRspIpAddressIndex INTEGER
  scGenPortIPAddressRspIpAddress IpAddress

ScEthPortEntry  
SEQUENCE    
  scEthPortGroupId INTEGER
  scEthPortId INTEGER
  scEthPortOctetsRec Counter
  scEthPortPktsRec Counter
  scEthPortGoodBroadcastPktsRec Counter
  scEthPortGoodMulticastPktsRec Counter
  scEthPortCRCAlignErrors Counter
  scEthPortOversizePkts Counter
  scEthPortFragments Counter
  scEthPortJabber Counter
  scEthPortCollisions Counter
  scEthPortPkts64Octets Counter
  scEthPortPkts65to127Octets Counter
  scEthPortPkts128to255Octets Counter
  scEthPortPkts256to511Octets Counter
  scEthPortPkts512to1023Octets Counter
  scEthPortPkts1024to1518Octets Counter
  scEthPortGoodPktsRec Counter
  scEthPortBadPkts Counter
  scEthPortGoodOctetsRec Counter
  scEthPortBadOctets Counter
  scEthPortGoodBroadcastOctetsRec Counter
  scEthPortGoodMulticastOctetsRec Counter
  scEthPortGoodOctetsSent Counter
  scEthPortGoodPktsSent Counter
  scEthPortLateCollisions Counter
  scEthPortFunctionalStatus INTEGER
  scEthPortMode INTEGER
  scEthPortSpeed INTEGER
  scEthPortAutoNegotiation INTEGER
  scEthPortAutoNegotiationStatus INTEGER
  scEthPortTotalOctets Counter
  scEthPortTotalPkts Counter
  scEthPortDropEvents Counter
  scEthPortGigaPauseStatus INTEGER
  scEthPortLower32OctetsRec Counter
  scEthPortUpper32OctetsRec Counter
  scEthPortLower32OctetsSent Counter
  scEthPortUpper32OctetsSent Counter
  scEthPortGoodUnicastPktsRec Counter
  scEthPortDiscardPktsRec Counter
  scEthPortUnicastPktsSent Counter
  scEthPortDiscardPktsSent Counter
  scEthPortPauseCapabilities INTEGER
  scEthPortMulticastPktsSent Counter
  scEthPortUndersizePktsRec Counter
  scEthPortFlowControl INTEGER

ScEthGroupEntry  
SEQUENCE    
  scEthGroupId INTEGER
  scEthGroupAutoPartitionEnable INTEGER
  scEthGroupFefiEnable INTEGER

Defined Values

switchChip 1.3.6.1.4.1.81.28
OBJECT IDENTIFIER    

scGen 1.3.6.1.4.1.81.28.1
OBJECT IDENTIFIER    

scGenChassis 1.3.6.1.4.1.81.28.1.1
OBJECT IDENTIFIER    

scGenChMainAgPosition 1.3.6.1.4.1.81.28.1.1.1
This attribute defines the position in the chassis where the Main Agent resides.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..4  

scGenChRedunAgPosition 1.3.6.1.4.1.81.28.1.1.2
This attribute defines the position in the chassis where the Redundant Agent resides. 0 means Redundant Agent not present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..4  

scGenChRedunAgActivityStatus 1.3.6.1.4.1.81.28.1.1.3
This attribute defines the status of the Redundant Agent. notPresent(1) - indicates that no redundant Agent exists. dormant(2) - indicates that the redundant Agent is ok and may at any moment become the Agent of the system. active(3) - indicates that the redundant Agent is acting as the Agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notPresent(1), dormant(2), active(3), notSupported(255)  

scGenChAgVLAN 1.3.6.1.4.1.81.28.1.1.4
The Virtual LAN number of the Agent's internal interface. The value 0 means Generic ( But can communicate with Global !). The values '255' mean Global.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

scGenMon 1.3.6.1.4.1.81.28.1.2
OBJECT IDENTIFIER    

scGenMonTable 1.3.6.1.4.1.81.28.1.2.1
Table of attributes which define Monitoring information about a single XSwitch in SC based devices.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenMonEntry

scGenMonEntry 1.3.6.1.4.1.81.28.1.2.1.1
An entry in the table, containing data about a single XSwitch.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenMonEntry  

scGenMonSwitchId 1.3.6.1.4.1.81.28.1.2.1.1.1
Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenMonDropEvents 1.3.6.1.4.1.81.28.1.2.1.1.2
The total number of events in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonOctets 1.3.6.1.4.1.81.28.1.2.1.1.3
The total number of good octets switched and error octets filtered by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonPkts 1.3.6.1.4.1.81.28.1.2.1.1.4
The total number of good packets switched and error packets filtered by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonGoodBroadcastPkts 1.3.6.1.4.1.81.28.1.2.1.1.5
The total number of good packets switched by this XSwitch that were directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonGoodMulticastPkts 1.3.6.1.4.1.81.28.1.2.1.1.6
The total number of good packets switched by this XSwitch that were directed to the multicast address. Note that this number does not include packets directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonGoodPkts 1.3.6.1.4.1.81.28.1.2.1.1.7
The total number of good packets switched by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonBadPkts 1.3.6.1.4.1.81.28.1.2.1.1.8
The total number of bad packets filtered by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonGoodOctets 1.3.6.1.4.1.81.28.1.2.1.1.9
The total number of good octets switched by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonBadOctets 1.3.6.1.4.1.81.28.1.2.1.1.10
The total number of bad octets filtered by this XSwitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonSmonCapability 1.3.6.1.4.1.81.28.1.2.1.1.11
This item is used to define which smon's application are implemented in the agent. When the console first performs smon application it should read this item in order to know which of the smon's applications are available in this agent's version. When there is a value of 0 (zero) in the relevant bit it means that the assosiated application is not supported, When there is a value of 1 (one) in the relevant bit it means that the assosiated application is supported. D0 - Statistics. D1 - History. D2 - Alarms. D3 - Host. D4 - HostTopN. D5 - Metrix. D6 - Filter. D7 - Capture. D8 - Event. D9 - TokenRing. D10 - ProtocolDir. D11 - ProtocolDist. D12 - AddressMap. D13 - NlHost. D14 - NlMatrix. D15 - AlHost. D16 - AlMatrix. D17 - UsrHistory. D18 - ProbConfig. D19 - Port. D20 - PortTopN. D21 - Subnet. D22 - SubnetMatrix. D23 - Vlan. D24 - VlanMatrix. D25 - nlHostTopN D26 - portHistory
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

scGenMonMIBCtrMode 1.3.6.1.4.1.81.28.1.2.1.1.12
This object defines for switch ports to include/exclude local segment traffic in their port counters
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenMonSwitchVLANList 1.3.6.1.4.1.81.28.1.2.1.1.13
A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

scGenMonMIBCtrList 1.3.6.1.4.1.81.28.1.2.1.1.14
A bitmap defining the status of the MIBCtrMode for every group in the switch. The MSB (Most significant bit) representing the status of group #1. If MIBCtrMode on a group is enable(1) the bit is set to 1, otherwise 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

scGenMonTimeStamp 1.3.6.1.4.1.81.28.1.2.1.1.15
This attribute contains the value of sysUpTime at the time switch counters were calculated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

scGenMonVlanTimeStamp 1.3.6.1.4.1.81.28.1.2.1.1.16
This attribute contains the value of sysUpTime at the time VLAN counters were calculated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

scGenMonPriorityTable 1.3.6.1.4.1.81.28.1.2.2
A list of priority count entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenMonPriorityEntry

scGenMonPriorityEntry 1.3.6.1.4.1.81.28.1.2.2.1
A list of statistics related to a specific priority level on a single XSwitch in SC based devices.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenMonPriorityEntry  

scGenMonPrioritySwitchId 1.3.6.1.4.1.81.28.1.2.2.1.1
Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenMonPriorityId 1.3.6.1.4.1.81.28.1.2.2.1.2
The priority for which this entry reports statistics. 1=regular. 2=high.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

scGenMonPriorityGoodPkts 1.3.6.1.4.1.81.28.1.2.2.1.3
The total number of good packets switched by this XSwitch using this packet priority level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonPriorityGoodOctets 1.3.6.1.4.1.81.28.1.2.2.1.4
The total number of good octets switched by this XSwitch using this packet priority level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonVLANList 1.3.6.1.4.1.81.28.1.2.3
A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

scGenMonVLANTable 1.3.6.1.4.1.81.28.1.2.4
A list of virtual LAN statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenMonVLANEntry

scGenMonVLANEntry 1.3.6.1.4.1.81.28.1.2.4.1
A list of statistics related to a specific Virtual LAN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenMonVLANEntry  

scGenMonVLANSwitchId 1.3.6.1.4.1.81.28.1.2.4.1.1
Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenMonVLANId 1.3.6.1.4.1.81.28.1.2.4.1.2
The Virtual LAN for which this entry contains information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenMonVLANGoodPkts 1.3.6.1.4.1.81.28.1.2.4.1.3
The total number of good packets switched by the XSwitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonVLANGoodOctets 1.3.6.1.4.1.81.28.1.2.4.1.4
The total number of good octets switched by the XSwitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonVLANStatsUcastPkts 1.3.6.1.4.1.81.28.1.2.4.1.5
The total number of good unicast packets switched by the XSwitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonVLANStatsMcastPkts 1.3.6.1.4.1.81.28.1.2.4.1.6
The total number of good multicast packets switched by the XSwitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonVLANStatsBcastPkts 1.3.6.1.4.1.81.28.1.2.4.1.7
The total number of good broadcast packets switched by the XSwitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenMonSwitches 1.3.6.1.4.1.81.28.1.2.5
A bitmap defining the switch status, whether it is functional or not. The list should start with the MSB. Value of each bit: 0 - the switch is not functional 1 - the switch is functional The mapping is: Bit 0 : Left DomainX Bit 1 : Right DomainX
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

scHostTimePortCorrTable 1.3.6.1.4.1.81.28.1.2.6
An addition to the RMON MIB's hostTimeTable. This table contains a list of MAC addresses that were monitored on the switch and the ports to which they are connected. The index of this table is the same as for the standard RMON hostTimeTable. Indexes are scHostTimeCreationOrder and scHostTimeIndex. The MAC address is stored in scHostTimeAddress. The port to which the MAC address is connected is defined in scHostTimePortConnection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScHostTimePortCorrEntry

scHostTimePortCorrEntry 1.3.6.1.4.1.81.28.1.2.6.1
An entry in the MAC to port correlation table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScHostTimePortCorrEntry  

scHostTimeAddress 1.3.6.1.4.1.81.28.1.2.6.1.1
The physical address of this host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scHostTimeCreationOrder 1.3.6.1.4.1.81.28.1.2.6.1.2
An index that uniquely identifies an entry in the hostTime table among those entries associated with the same hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes is based on the order of each entry's insertion into the table, in which entries added earlier have a lower index value than entries added later. Thus the management station has the ability to learn of new entries added to this table without downloading the entire table. It is important to note that the index for a particular entry may change as an (earlier) entry is deleted from the table. Because this order may change, management stations should make use of the hostControlLastDeleteTime variable in the hostControlEntry associated with the relevant portion of the hostTimeTable. By observing this variable, the management station may detect the circumstances where a download of the table may have missed entries, and where a previous association between a value of hostTimeCreationOrder and a hostTimeEntry may no longer hold.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

scHostTimeIndex 1.3.6.1.4.1.81.28.1.2.6.1.3
The set of collected RMON host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

scHostTimePortConnection 1.3.6.1.4.1.81.28.1.2.6.1.4
The switch port to which this scHostTimeAddress is connected. The coding of the port number for Visage switches is: 32*(H-1)+P, where H is the number of the hub in the stack and P the port in the hub (1.. 32). For hosts whose port connection is not identified by the agent, the value of this item will be 65,535
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroup 1.3.6.1.4.1.81.28.1.3
OBJECT IDENTIFIER    

scGenGroupTable 1.3.6.1.4.1.81.28.1.3.1
Table of attributes which define general configuration information about a single SC based group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenGroupEntry

scGenGroupEntry 1.3.6.1.4.1.81.28.1.3.1.1
An entry in the table, containing data about a single Group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenGroupEntry  

scGenGroupId 1.3.6.1.4.1.81.28.1.3.1.1.1
Unique Id of the group in the scGenGroupTable. Equals the number of the slot by which the group is accessed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroupUseSwitches 1.3.6.1.4.1.81.28.1.3.1.1.2
This attribute reflects the status of the `Use Switches' switch which defines the working mode of the module. on - The module works according to the switches. No Set commands may be performed on attributes related to the switches. off - Ignore Dip Switches, use stored parameters and accept all Set commands.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenGroupCopyPortSupport 1.3.6.1.4.1.81.28.1.3.1.1.3
Indication whether a module supports Copy-Port [on(1)], or does not support Copy-Port [off(2)].
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenGroupXswitchConnection 1.3.6.1.4.1.81.28.1.3.1.1.4
This attribute identifies the Xswitch number (1..4) to which the module is connected to. In non-bridged configuration, there are potentialy up to 4 Xswitches - 1&2 for left&right Ethernet Xswitches and 3&4 for left&right TR Xswitches. In bridged configuration, there are potentialy 2 Xswitches - 1 for Ethernet Xswitch and 2 for TR Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenGroupStatus 1.3.6.1.4.1.81.28.1.3.1.1.5
This attributes defines the status of the Xswitch module. The value 'loadsBudgetProblem' indicates that the module cannot be connected to the Xswitch because it exceeds the maximum number of loads allowed in the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), loadsBudgetProblem(2), notSupported(255)  

scGenGroupSwitchType 1.3.6.1.4.1.81.28.1.3.1.1.6
This attribute defines the Xswitch type of the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), token-ring(2), notSupported(255)  

scGenGroupNumberOfLoads 1.3.6.1.4.1.81.28.1.3.1.1.7
This attribute identifies the number of loads which that Xswitch module represents.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenGroupSetDefaults 1.3.6.1.4.1.81.28.1.3.1.1.8
Set all module and ports parameters in the XSwitch module, to their default values. This item will always return a value of off(2), since it acts like a toggle switch. Set of layer2Only(3) value, will cause partial setting, to layer2 parameters only
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), layer2Only(3), notSupported(255)  

scGenGroupSupportCopyPortList 1.3.6.1.4.1.81.28.1.3.1.1.9
A bitmap defining the status of each port of the hub\module whether it support copy port or not, 0 - the port does not support copy port 1 - the port support the copy port the list should start with the MSB indicates port number 1 (one) and the LSB indicates the highest number of the ports in the hub\module. For Example: if a module\hub has 8 ports and ports number 1,3,4 support copy port while the other don't, the bitmap will be: 10110000.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupSupportPortCountersList 1.3.6.1.4.1.81.28.1.3.1.1.10
A bitmap defining the status of each port of the hub\module whether it supports the port's counters, 0 - the port does not support port's counters 1 - the port support the port's counters the list should start with the MSB indicates port number 1 (one) and the LSB indicates the highest number of the ports in the hub\module. For Example: if a module\hub has 8 ports and ports number 1,3,4 support port's counters while the other don't, the bitmap will be: 10110000.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupSupportSegCountersList 1.3.6.1.4.1.81.28.1.3.1.1.11
A bitmap defining the status of each port of the hub\module whether it supports the segment counters on port, 0 - the port does not support segment's counters 1 - the port support the segment's counters the list should start with the MSB indicates port number 1 (one) and the LSB indicates the highest number of the ports in the hub\module. For Example: if a module\hub has 8 ports and ports number 1,3,4 support segment's counters while the other don't, the bitmap will be: 10110000.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupUpLinkType 1.3.6.1.4.1.81.28.1.3.1.1.12
The type of the Up Link port Relevant only for the 25th port of Visage 2500: Fiber (1) - 100BaseFX, Copper (2) -100BaseTX.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fiber(1), copper(2), notSupported(255)  

scGenGroupPlugInType 1.3.6.1.4.1.81.28.1.3.1.1.13
Attribute describing the type of the plug-in module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cajunX120T8(1), cajunX120F2(2), cajunX120S1(3), cajunX120S2(4), cajunX120L1(5), cajunX120L2(6), cajunX120T16(7), cajunX120F4(8), cajunX120G2(9), cajunX120GT2(10), cajunX330T16(11), cajunX330F4(12), cajunX330F2(13), cajunX330L2(14), cajunX330S2(15), cajunX330L1(16), cajunX330S1(17), cajunX330-OC12F1(18), cajunX330-OC12F2(19), cajunX330-OC3F1(20), cajunX330-OC3F2(21), cajunX330-OC12S1(22), cajunX330-OC12S2(23), cajunX330GT4(24), cajunX330GT2(25), cajunX330G2(26), cajunX330SSM(27), cajunX130F2(31), cajunX130G2(32), cajunX130GT2(33), unknown(254), none(255)  

scGenGroupPlugInDescr 1.3.6.1.4.1.81.28.1.3.1.1.14
Descriptor of the plug-in in ASCII (readable) format, mainly for use with Generic management applications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenGroupPlugInCS 1.3.6.1.4.1.81.28.1.3.1.1.15
ASCII string for description and display of the plug-in module configuration symbol. The format of the number is XXXX.YY
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

scGenGroupDefaultVLAN 1.3.6.1.4.1.81.28.1.3.1.1.16
Attribute describing the Default VLAN configuration on the switch ports of the module. It is determined according to scGenSwitchDefaultVLAN parameter of the agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER vlan0(1), vlan1(2), notSupported(255)  

scGenGroupCascadingType 1.3.6.1.4.1.81.28.1.3.1.1.17
Attribute describing the type of the cascding module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cajunX330STK(1), cajunX330MLSTK(2), unknown(254), none(255)  

scGenGroupCascadingDescr 1.3.6.1.4.1.81.28.1.3.1.1.18
Descriptor of the cascading module in ASCII (readable) format, mainly for use with Generic management applications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenGroupCascadingCS 1.3.6.1.4.1.81.28.1.3.1.1.19
ASCII string for description and display of the cascading module configuration symbol. The format of the number is XXX.YYY
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

scGenGroupSupportDstCopyPortList 1.3.6.1.4.1.81.28.1.3.1.1.20
A bitmap defining the status of each port of the hub\module whether it supports the capability of being a destination copy-port . 1 - the port has the capability of being a destination copy-port 0 - the port does not have the capability of being a destination copy-port The list should start with the MSB indicating port number 1 (one) and the LSB indicating the highest number of the ports in the hub\module. For Example: if a module\hub has 8 ports and ports number 1,3,4 can be destination copy ports, while the others cannot, then the bitmap will be: 10110000.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupBUPSType 1.3.6.1.4.1.81.28.1.3.1.1.21
Attribute describing the type of the BUPS module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ac(1), dc(2), none(255)  

scGenGroupBUPSCS 1.3.6.1.4.1.81.28.1.3.1.1.22
ASCII string for description and display of the BUPS module configuration symbol. The format of the number is X.Y
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

scGenGroupBUPSFansStatus 1.3.6.1.4.1.81.28.1.3.1.1.23
The operational status of the fans included in the BUPS module: allFansOK(1) - all BUPS module's fans are operational. oneFanFailed(2) - at least one of the BUPS module's fan is failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER allFansOK(1), oneFanFailed(2), notSupported(255)  

scGenGroupFansStatus 1.3.6.1.4.1.81.28.1.3.1.1.24
The operational status of the fans included in the module: allFansOK(1) - all module's fans are operational. oneFanFailed(2) - at least one of the module's fan is failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER allFansOK(1), oneFanFailed(2), notSupported(255)  

scGenGroupInternalBuffering 1.3.6.1.4.1.81.28.1.3.1.1.25
Control the internal buffering capacity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER min(1), max(2), med(3), notSupported(255)  

scGenGroupMcFilterBoxSupport 1.3.6.1.4.1.81.28.1.3.1.1.26
Tells whether the box hardware supports filtering or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filteringSupported(1), filterNotSupport(2), notSupported(255)  

scGenGroupMcFilterPersonalitySupport 1.3.6.1.4.1.81.28.1.3.1.1.27
Tells whether the personality hardware supports filtering or not. The value PersonalityNotInstalld means that the a personality Extention was not installed in the specific box
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filteringSupported(1), filterNotSupport(2), personalityNotInstalled(3), notSupported(255)  

scGenGroupMcFilterStackingSupport 1.3.6.1.4.1.81.28.1.3.1.1.28
Tells whether the stacking hardware supports filtering or not The value StackingNotInstalld means that the a stacking daughter board was not installed in the specific box
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filteringSupported(1), filterNotSupport(2), stackingNotInstalled(3), notSupported(255)  

scGenGroupLACPMode 1.3.6.1.4.1.81.28.1.3.1.1.29
The value of this attribute determines whether LACPDU messages can be exchanged by the module's ports. If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB. If disabled, every port of the module will not exchange LACPDU messages - regardless of there scGenPortLACPMode MIB. This MIB is required for internal communication between the agent and its sub-agents, in order to distribute throughout the switch's modules the setting made on the scGenSwitchLACPMode MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scGenGroupSecurityMode 1.3.6.1.4.1.81.28.1.3.1.1.30
Group intrusion security mode assigned to this module. securityMode - all ports in this module are secure according to their scGenPortSecurityMode MIB's value. nonSecurityMode - all ports in this module are not secure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonSecurityMode(1), securityMode(2), notSupported(255)  

scGenGroupBroadcastStormControl 1.3.6.1.4.1.81.28.1.3.1.1.31
Set the Broadcast Storm Control function on all switch ports. On means that Broadcast, Multicast or Unknown packets are discarded on an ingress port, when the rate of those packets, received on the port, is above the scGenGroupBroadcastThreshold, as set by the user.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenGroupBroadcastThreshold 1.3.6.1.4.1.81.28.1.3.1.1.32
Set the Rate Threshold, in packets per second, above which Broadcast, Multicast or Unknown packets are discarded on ingress port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..144000  

scGenGroupPriorityQueuesScheduling 1.3.6.1.4.1.81.28.1.3.1.1.33
Set the Priority Queues Scheduling scheme for packets transmission from egress ports. Strict - will serve higher priority queue before lower priority queue, as long as the higher queue has packets. Weighted - will serve higher priority queue before lower priority queue, but will save specific bandwidth for each queue in order to avoid starvation of lower priority queues.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER strict(1), weighted(2), notSupported(255)  

scGenGroupBoundedDelay 1.3.6.1.4.1.81.28.1.3.1.1.34
Set the Bounded Delay function in the switch. On will ensure that time-sensitive packets will be forwarded through the switch in no more than a maximum delay.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenGroupSLDAdminStatus 1.3.6.1.4.1.81.28.1.3.1.1.35
set the Self Loop Discovery application to enable/disable. This works with the scGenPortSLDAdminStatus
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenGroupSmonTable 1.3.6.1.4.1.81.28.1.3.2
Table of smon capabilities in a single group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenGroupSmonEntry

scGenGroupSmonEntry 1.3.6.1.4.1.81.28.1.3.2.1
An entry in the table, containing data about a single Group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenGroupSmonEntry  

scGenGroupSmonGroupId 1.3.6.1.4.1.81.28.1.3.2.1.1
Unique Id of the group in the scGenGroupSmonTable. Equals the number of the slot by which the group is accessed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroupSmonCapability 1.3.6.1.4.1.81.28.1.3.2.1.2
This item is used to define which smon's application are implemented in the group. When there is a value of 0 (zero) in the relevant bit it means that the assosiated application is not supported. When there is a value of 1 (one) in the relevant bit it means that the assosiated application is supported. D0 - Statistics. D1 - History. D2 - Alarms. D3 - Host. D4 - HostTopN. D5 - Metrix. D6 - Filter. D7 - Capture. D8 - Event. D9 - TokenRing. D10 - ProtocolDir. D11 - ProtocolDist. D12 - AddressMap. D13 - NlHost. D14 - NlMatrix. D15 - AlHost. D16 - AlMatrix. D17 - UsrHistory. D18 - ProbConfig. D19 - Port. D20 - PortTopN. D21 - Subnet. D22 - SubnetMatrix. D23 - Vlan. D24 - VlanMatrix.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

scGenGroupSmonVlanList 1.3.6.1.4.1.81.28.1.3.2.1.3
A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

scGenGroupSmonDropEvents 1.3.6.1.4.1.81.28.1.3.2.1.4
The total number of events ,in this group, in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonGoodBroadcastPkts 1.3.6.1.4.1.81.28.1.3.2.1.5
The total number of good broadcast packets in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonGoodMulticastPkts 1.3.6.1.4.1.81.28.1.3.2.1.6
The total number of good multicast packets, in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonGoodPkts 1.3.6.1.4.1.81.28.1.3.2.1.7
The total number of good packets, in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonBadPkts 1.3.6.1.4.1.81.28.1.3.2.1.8
The total number of bad packets , in this group, filtered by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonGoodOctets 1.3.6.1.4.1.81.28.1.3.2.1.9
The total number of good octets, in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonBadOctets 1.3.6.1.4.1.81.28.1.3.2.1.10
The total number of bad octets, in this group, filtered by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonPkts 1.3.6.1.4.1.81.28.1.3.2.1.11
The total number of packets, good and bad, in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonOctets 1.3.6.1.4.1.81.28.1.3.2.1.12
The total number of octets, good and bad, in this group, switched by the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupSmonMIBCtrMode 1.3.6.1.4.1.81.28.1.3.2.1.13
This object defines for group ports to include/exclude local segment traffic in their port counters
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenGroupVlanTable 1.3.6.1.4.1.81.28.1.3.3
Table of attributes which define general VLAN counters of a single SC based group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenGroupVlanEntry

scGenGroupVlanEntry 1.3.6.1.4.1.81.28.1.3.3.1
An entry in the table, containing VLAN counters in a single Group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenGroupVlanEntry  

scGenGroupVlanGroupId 1.3.6.1.4.1.81.28.1.3.3.1.1
Unique Id of the group in the scGenGroupVlanTable. Equals the number of the slot by which the group is accessed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroupVlanId 1.3.6.1.4.1.81.28.1.3.3.1.2
The Virtual LAN for which this entry contains information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroupVlanUcastPkts 1.3.6.1.4.1.81.28.1.3.3.1.3
The total number of good unicast packets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanMcastPkts 1.3.6.1.4.1.81.28.1.3.3.1.4
The total number of good multicast packets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanBcastPkts 1.3.6.1.4.1.81.28.1.3.3.1.5
The total number of good broadcast packets in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanGoodPkts 1.3.6.1.4.1.81.28.1.3.3.1.6
The total number of good packets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanGoodOctets 1.3.6.1.4.1.81.28.1.3.3.1.7
The total number of good octets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanUcastOctets 1.3.6.1.4.1.81.28.1.3.3.1.8
The total number of good unicast octets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanMcastOctets 1.3.6.1.4.1.81.28.1.3.3.1.9
The total number of good multicast octets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanBcastOctets 1.3.6.1.4.1.81.28.1.3.3.1.10
The total number of good broadcast octets ,in this group, switched by the Xswitch on this Virtual LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scGenGroupVlanCurrentEgressPorts 1.3.6.1.4.1.81.28.1.3.3.1.11
The set of ports in this module which are transmitting traffic for this vlan as either tagged or untagged frames. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. This MIB is for internal agent sub-agent communication, it is aimed to distribute the standard dot1qVlanCurrentEgressPorts among the modules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupVlanCurrentUntaggedPorts 1.3.6.1.4.1.81.28.1.3.3.1.12
The set of ports which are transmitting traffic for this VLAN as untagged frames. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. This MIB is for internal agent sub-agent communication, it is aimed to distribute the standard dot1qVlanCurrentUntaggedPorts among the modules. It is updated together with genPortVLANMode MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenGroupVlanStaticEgressPorts 1.3.6.1.4.1.81.28.1.3.3.1.13
The set of ports in this module which are permanently assigned to the egress list for this VLAN by management. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object is a string of zeros long by 128 bits, indicating not fixed. This MIB is for internal agent sub-agent communication, it is aimed to distribute the standard dot1qVlanStaticEgressPorts among the modules.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

scGenGroupVlanStaticUntaggedPorts 1.3.6.1.4.1.81.28.1.3.3.1.14
The set of ports which should transmit egress packets for this VLAN as untagged. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option. It is updated together with genPortVLANMode MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

scGenGroupRspTable 1.3.6.1.4.1.81.28.1.3.4
.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenGroupRspEntry

scGenGroupRspEntry 1.3.6.1.4.1.81.28.1.3.4.1
.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenGroupRspEntry  

scGenGroupRspGroupId 1.3.6.1.4.1.81.28.1.3.4.1.1
Unique Id of the group in the scGenGroupRspTable. Equals the number of the slot by which the group is accessed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenGroupRspHelloInterval 1.3.6.1.4.1.81.28.1.3.4.1.2
The interval between transmissions of hello-messages, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspDevicePollingInterval 1.3.6.1.4.1.81.28.1.3.4.1.3
The interval between transmissions of ARP queries for polling connectivity to the device, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspDeviceNotRespondingTimeout 1.3.6.1.4.1.81.28.1.3.4.1.4
Amount of time in which no ARP-replies are received from the device, which cause the RSP to assume no connection to that device, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspSwitchNotRespondingTimeout 1.3.6.1.4.1.81.28.1.3.4.1.5
Amount of time in which no hello-messages with acknowledge are received from the other switch, which cause the RSP to assume no connection to that switch, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspMoveToForwardingInterval 1.3.6.1.4.1.81.28.1.3.4.1.6
Amount of time the port waits upon deciding to move to forwarding mode, until it moves to that mode, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspBroadcastArpShortInterval 1.3.6.1.4.1.81.28.1.3.4.1.7
The interval in which the switch should send broadcast ARPs to the device when not knowing the MAC-address of the device, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspBroadcastArpShortIntervalNumber 1.3.6.1.4.1.81.28.1.3.4.1.8
The number of broadcast ARPs the switch should send in short interval time, when not knowing the MAC address of the device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspBroadcastArpLongInterval 1.3.6.1.4.1.81.28.1.3.4.1.9
The interval in which the switch should send broadcast ARPs to the device when the device does not respond to unicast ARPs, in 100mSec units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenGroupRspPeriodicPingsBoxIpAddress 1.3.6.1.4.1.81.28.1.3.4.1.10
This MIB-item is the IP-address that the P330 box uses in order to periodically ping to devices Default value for IP Address is 0.0.0.0
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

scGenGroupRspPeriodicPingsDestinationIpAddress 1.3.6.1.4.1.81.28.1.3.4.1.11
This MIB-item sets an IpAddress that the devices will be configured to periodically ping to. The switch will be responsible to reply to ARP-queries concerning this IP-address, and which were issued by devices directly attached to it. A value of 0.0.0.0 in this Mib Item means that it does not describe an existing IpAddress. Default value for IP Address is 0.0.0.0
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

scGenGroupRspMode 1.3.6.1.4.1.81.28.1.3.4.1.12
Sets the mode of the module from the RSP-application prespective. Possible modes are: RSP-module-mode-role-A - means that the ports of this module perform the RSP scheme for a device connected through a repeater, in role A (primary role). RSP-module-mode-role-B - means that the ports of this module perform the RSP scheme for a device connected through a repeater, in role B (secondary role).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rsp-module-mode-role-A(1), rsp-modue-mode-role-B(2), notSupported(255)  

scGenPort 1.3.6.1.4.1.81.28.1.4
OBJECT IDENTIFIER    

scGenPortTable 1.3.6.1.4.1.81.28.1.4.1
Table of attributes which define general configuration information about a single SC based port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenPortEntry

scGenPortEntry 1.3.6.1.4.1.81.28.1.4.1.1
An entry in the table, containing data about a single Port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenPortEntry  

scGenPortGroupId 1.3.6.1.4.1.81.28.1.4.1.1.1
Id of the group to which the port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortId 1.3.6.1.4.1.81.28.1.4.1.1.2
Unique Id of the port in the scEthPortTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortVLAN 1.3.6.1.4.1.81.28.1.4.1.1.3
The Virtual LAN number of the Port. The value 0 means Generic ( But can communicate with Global !). The value '255' means Global.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4095  

scGenPortPriority 1.3.6.1.4.1.81.28.1.4.1.1.4
The priority level of the packets send by the Port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER regular(1), high(2), userPriority1(3), userPriority2(4), userPriority3(5), userPriority4(6), userPriority5(7), userPriority6(8), userPriority7(9), userPriority8(10), notSupported(255)  

scGenPortSetDefaults 1.3.6.1.4.1.81.28.1.4.1.1.5
Set all port parameters in the XSwitch module, to their default values. This item is used for ports that are managed by Sub-agents. This item will always return a value of off(2), since it acts like a toggle switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenPortBackbone 1.3.6.1.4.1.81.28.1.4.1.1.6
The type of the Xswitch port. 'on' indicates that the port was discovered by VIDP as backbone port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenPortCopyMode 1.3.6.1.4.1.81.28.1.4.1.1.7
Enable /Disable the Copy Port mode in the Sub-Agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenPortCopyDestination 1.3.6.1.4.1.81.28.1.4.1.1.8
The destination of the copied information. The destination can be another port or the Agent acting as an RMON probe. The value of this item is: LSB Byte= sniffer channel number, Next Byte= sniffer device number. When sniffer device number=31, the destination is the Agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..8092  

scGenPortLinkAggregationNumber 1.3.6.1.4.1.81.28.1.4.1.1.9
The Link Aggregation Group (LAG) number, to which the Port belongs. The value 0 means that this port is not part of a LAG. This is also the default.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

scGenPortSendBridgedPackets 1.3.6.1.4.1.81.28.1.4.1.1.10
When set to on(1), the port will transmit to the line bridged frames (for which their secondary VLAN was 0xFFE internally). This is the case for ports connected to a station or to another switch that has no bridging capabilities. When set to off(2), the port will reject the bridged frames, by not sending them to the line. This is the case for ports connected to another switch that has its own bridging capabilities. Default value is on(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenPortVLANEgressStaticConfiguration 1.3.6.1.4.1.81.28.1.4.1.1.11
A bitmap defining the VLANs, for which the port is member in their Egress Tables. The first bit is for VLAN 0, the second bit for VLAN 1, and so on. If the port is member in the Egress Table of a specified VLAN, then the value of the associated bit is 1, otherwise 0. The actual VLAN Table configuration, according to this item, is done only when scGenPortStaticVLANBinding is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

scGenPortStaticVLANBinding 1.3.6.1.4.1.81.28.1.4.1.1.12
This object defines whether Static VLAN Binding is enabled or disabled on the port. If enabled, the port is member in the Egress List of the VLANs, as specified in scGenPortVLANEgressStaticConfiguration, in addition to its Port VLAN. If disabled, the port is member in the Egress List of the VLANs, according to the VLAN Tagging mode of the port - i.e. if VLAN Tagging mode is Clear, then the Port is member in the Egress List of only the Port VLAN. If VLAN Tagging mode is 802.1Qtagging, then the Port is member in the Egress List of all VLANs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenPortSecId 1.3.6.1.4.1.81.28.1.4.1.1.13
The identification number (per module) of the switching chip to which the port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenPortMaxLagsOnSec 1.3.6.1.4.1.81.28.1.4.1.1.14
The theoretic maximum number of LAGs that can be defined over the switching chip to which the port belongs. The value is fixed according to the switching chip type: For the Timpani chip, the value is 1. For the Guitar chip, the value is 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

scGenPortGenericTrap 1.3.6.1.4.1.81.28.1.4.1.1.15
The value of this attribute determines whether or not the agent sends the snmp generic traps 2 and 3, for link down/up events on this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scGenPortLACPMode 1.3.6.1.4.1.81.28.1.4.1.1.16
The value of this attribute determines whether the port exchanges LACPDU messages, in agreement with the scGenGroupLACPMode MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scGenPortLastIntruderSourceAddr 1.3.6.1.4.1.81.28.1.4.1.1.17
Ethernet source address of the last intrusion attempt at this port. The value of this item will be 000000 (a string of 6 zeros) if security mode is disable or no security violation at this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenPortSecurityMode 1.3.6.1.4.1.81.28.1.4.1.1.18
Security mode assigned to this port. nonSecurityMode - do not perform intrusion control security mechanism on this port. securityMode - perform intrusion control security mechanism and trap the console in case of security violation, if both scGenGroupSecurityMode and scGenSwitchSecurityMode are in this mode too.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonSecurityMode(1), securityMode(2), notSupported(255)  

scGenPortSTA 1.3.6.1.4.1.81.28.1.4.1.1.19
Enable /Disable the Spanning Tree protocol for this port, meaningless when disabled at the switch level via the scGenSwitchSTA MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenPortLagCapability 1.3.6.1.4.1.81.28.1.4.1.1.20
An octet string with the size of the maximum number of LAGs on the device. Each bit represents a LAG which the port may be associated with (a member of).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenPortCapability 1.3.6.1.4.1.81.28.1.4.1.1.21
Port capability bit mask, where each bit represent the capability of the port: Bit #1 - 10Mbps speed support Bit #2 - 100Mbps speed support Bit #3 - 1000Mbps speed support Bit #4 - 10000Mbps speed support Bit #9 - 2 queues support Bit #10 - 4 queues support Bit #11 - 8 queue support Bit #17 - CopyPort Tx support Bit #18 - CopyPort Rx support Bit #19 - CopyPort Tx&Rx support Bit #20 - CopyPort filtering support Bit #25 - Symmetric FC support Bit #26 - AsymmetricTx FC support Bit #27 - AsymmetricRx FC support
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenPortSLDAdminStatus 1.3.6.1.4.1.81.28.1.4.1.1.22
Sets the admin status of each port in the Self Loop Discovery application A port which is disbaled does not send LDDU . A port which is enabled sends LDDU and migth turn to blocking if a SLD is discovered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

scGenPortSLDStatus 1.3.6.1.4.1.81.28.1.4.1.1.23
A port which is SLDEnabled can be in SelfLoop or NoSelfLoop mode . if the port is SLD disabled it will return notSupported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER selfLoop(1), noSelfLoop(2), notSupported(255)  

scGenPortRspTable 1.3.6.1.4.1.81.28.1.4.2
Table of attributes which define general configuration information about a single SC based port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenPortRspEntry

scGenPortRspEntry 1.3.6.1.4.1.81.28.1.4.2.1
An entry in the table, containing data about a single Port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenPortRspEntry  

scGenPortRspGroupId 1.3.6.1.4.1.81.28.1.4.2.1.1
Id of the group to which the port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortRspId 1.3.6.1.4.1.81.28.1.4.2.1.2
Unique Id of the port in the scGenPortRspTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortRspMode 1.3.6.1.4.1.81.28.1.4.2.1.3
Sets the mode of the port from the RSP-application perspective. Possible modes are: Regular - means that this is a regular port that does not participate in the RSP scheme, RSP-mode-role-A - means that this port performs the RSP scheme for a device connected through a repeater, in role A (primary role). RSP-mode-role-B - means that this port performs the RSP scheme for a device connected through a repeater, in role B (secondary role). device-mode - means that this port performs the RSP scheme for a device with two interfaces.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER regular(1), rsp-mode-role-A(2), rsp-mode-role-B(3), device-mode(4), notSupported(255)  

scGenSwitch 1.3.6.1.4.1.81.28.1.5
OBJECT IDENTIFIER    

scGenSwitchTable 1.3.6.1.4.1.81.28.1.5.1
Table of attributes which define information about a single XSwitch in SC based devices.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenSwitchEntry

scGenSwitchEntry 1.3.6.1.4.1.81.28.1.5.1.1
An entry in the table, containing data about a single XSwitch.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenSwitchEntry  

scGenSwitchId 1.3.6.1.4.1.81.28.1.5.1.1.1
Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenSwitchCopyMode 1.3.6.1.4.1.81.28.1.5.1.1.2
Enable /Disable the Copy Port mode in the XSwitch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenSwitchCopySource 1.3.6.1.4.1.81.28.1.5.1.1.3
The port in the switch that is being copied. All received and transmit packets on the port( including local traffic ) are copied to the defined destination, besides their normal destination. The value of this item is: 1024*S+P, where S is the slot number in the hub and P the port within the slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchCopyDestination 1.3.6.1.4.1.81.28.1.5.1.1.4
The destination of the copied information. The destination can be another port or the Agent acting as an RMON probe. The value of this item is: 1024*S+P, where S is the slot number in the hub and P is the port within the slot. Value 1023 means that the destination is the Agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchSetDefaults 1.3.6.1.4.1.81.28.1.5.1.1.5
Set all port parameters in the XSwitch, to their default values. This item will always return a value of off(2), since it acts like a toggle switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenSwitchVIDP 1.3.6.1.4.1.81.28.1.5.1.1.6
Enable /Disable the VIDP protocol supported in the XSwitch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenSwitchType 1.3.6.1.4.1.81.28.1.5.1.1.7
This attribute defines the type of the Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), token-ring(2), notSupported(255)  

scGenSwitchMasterId 1.3.6.1.4.1.81.28.1.5.1.1.8
This attribute defines which module in the Xswitch take the role of the Master. It is equal to the slot number of the Xswitch Master.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenSwitchReset 1.3.6.1.4.1.81.28.1.5.1.1.9
Setting this attribute to `on' will cause a reset to the Xswitch. Default value is 'off'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenSwitchNumberOfLoads 1.3.6.1.4.1.81.28.1.5.1.1.10
This attribute identifies the total number of loads of that Xswitch. There is a maximum budget of 30 loads on an single Xswitch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

scGenSwitchAgVLAN 1.3.6.1.4.1.81.28.1.5.1.1.11
The Virtual LAN number of the Agent's internal interface in the switch. The value 0 means Generic (But can communicate with Global !). The value '255' means Global.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4095  

scGenSwitchVLANList 1.3.6.1.4.1.81.28.1.5.1.1.12
A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

scGenSwitchSTA 1.3.6.1.4.1.81.28.1.5.1.1.13
Enable /Disable the Spanning Tree protocol support in the switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenSwitchSecurityMode 1.3.6.1.4.1.81.28.1.5.1.1.14
This item defines the Security mode per stack. nonSecurityMode - all ports in the stack are not secure. securityMode - all ports in the stack are secure according to their scGenPortSecurityMode MIB's value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonSecurityMode(1), securityMode(2), notSupported(255)  

scGenSwitchFindQuery 1.3.6.1.4.1.81.28.1.5.1.1.15
An address to be searched for by the Agent. The Agent will start look for the address when the value is different than Null. The string format is: 1st byte: address type - 0=MAC, 1=IP Next bytes: the address. (for MAC: next 6 bytes, for IP: next 4 bytes).
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

scGenSwitchFindResult 1.3.6.1.4.1.81.28.1.5.1.1.16
The search result. The result string format is: 1st byte: address type - 0=MAC, 1=IP. Next bytes: the address. (for MAC: next 6 bytes, for IP: next 4 bytes) 7-th byte (for MAC) or 5-th byte (for IP): number of ports with the specified address. Every next two bytes will indicate the slot and port number. 8-th byte (for MAC) or 6-th byte (for IP): slot number. 9-th byte (for MAC) or 7-th byte (for IP): port number. Etc. If the specified address was NOT found, the result will be with the 7-th byte (for MAC) or 5-th byte (for IP): byte equal to _0_.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenSwitchSWRdChange 1.3.6.1.4.1.81.28.1.5.1.1.17
A 4-byte octet-string indicating a change performed by the SW Redundancy task. The string will include: Byte 1: Group1 (module number). Byte 2 : Port1 Byte 3 : Group2 Byte 4 : port2 Where group2 port2 are the new enabled port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

scGenSwitchDefaultVLAN 1.3.6.1.4.1.81.28.1.5.1.1.18
Attribute describing the Default VLAN configuration on the switch ports. The user may change the value of this parameter through the setup terminal. Vlan1 is the standard default VLAN for port configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER vlan0(1), vlan1(2), notSupported(255)  

scGenSwitchVLANBridging 1.3.6.1.4.1.81.28.1.5.1.1.19
VLAN Bridging mode should be enabled in all Xswitches in the network, when the user wants to support network-wide VLAN Bridging. VLAN Bridging should also be enabled in one M-MLS, and PLS-Tagging mode should be set on the backbone ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenSwitchOldVersionModules 1.3.6.1.4.1.81.28.1.5.1.1.20
A list of modules, in ASCII format, that have older software versions than necessary in the switch. Module numbers are separated by a comma and a space. It is used to inform the user on version inconsistency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenSwitchVIDPNonSupportedModules 1.3.6.1.4.1.81.28.1.5.1.1.21
A list of modules, in ASCII format, that do not support the VIDP function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in VIDP function, as not all modules in the switch support VIDP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenSwitchSTANonSupportedModules 1.3.6.1.4.1.81.28.1.5.1.1.22
A list of modules, in ASCII format, that do not support the STA function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in STA function, as not all modules in the switch support STA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenSwitchIDSNonSupportedModules 1.3.6.1.4.1.81.28.1.5.1.1.23
A list of modules, in ASCII format, that do not support the IDS function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in IDS function, as not all modules in the switch support IDS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenSwitchMcFilter 1.3.6.1.4.1.81.28.1.5.1.1.24
Enable/disable the multicast filtering mechanism supported in the switch
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scGenSwitchMcFilterHostAgingTime 1.3.6.1.4.1.81.28.1.5.1.1.25
The Value of the Host-Aging-Time parameter used by the multicast filtering mechanism for aging learned multicast filtering information
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchMcFilterRouterAgingTime 1.3.6.1.4.1.81.28.1.5.1.1.26
The Value of the Router-Aging-Time parameter used by the multicast filtering mechanism for aging learned router-ports information
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchMcFilterDelayTime 1.3.6.1.4.1.81.28.1.5.1.1.27
The Value of the Delay-Time parameter used by the multicast filtering mechanism for waiting to all registration requests before applying a filter on a specific group
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchLACPMode 1.3.6.1.4.1.81.28.1.5.1.1.28
The value of this attribute determines whether LACPDU messages can be exchanged by the switch's ports. If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB. If disabled, every port of the switch will not exchange LACPDU messages - regardless of their scGenPortLACPMode MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

scGenSwitchSecurityModePermit 1.3.6.1.4.1.81.28.1.5.1.1.29
This item defines the Security mode per switch. This MIB is encoded in Lucent specific security mechanism.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenSwitchFastAgingOnRemoteTopChg 1.3.6.1.4.1.81.28.1.5.1.1.30
This item defines if the switch performs fast aging on the MAC address forwarding database (or reset the cam contents) upon reception of Topology Change BPDU from the STA root, indicating that a remote topology change has occurred. Local topology changes that occur on valuable ports always generate a fast aging anyway.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(255)  

scGenSwitchGigaMode 1.3.6.1.4.1.81.28.1.5.1.1.31
The value of this attribute determines the setting for the two Giga links of a P130 stack.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER regular(1), link-load-sharing(2), primary-bottom(3), primary-top(4)  

scGenSwitchCAMClear 1.3.6.1.4.1.81.28.1.5.1.1.32
When value sets to on(1), the switch clears its CAM table. This item will always return a value of off(2), since it acts like a toggle switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(255)  

scGenLinkAggregation 1.3.6.1.4.1.81.28.1.6
OBJECT IDENTIFIER    

scGenLinkAggregationTable 1.3.6.1.4.1.81.28.1.6.1
Table of attributes which define Link Aggregation Group in a single switch.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenLinkAggregationEntry

scGenLinkAggregationEntry 1.3.6.1.4.1.81.28.1.6.1.1
An entry in the table, containing LAG information in a single switch.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenLinkAggregationEntry  

scGenLinkAggregationId 1.3.6.1.4.1.81.28.1.6.1.1.1
The Link Aggregation number for which this entry contains information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

scGenLinkAggregationName 1.3.6.1.4.1.81.28.1.6.1.1.2
The Link Aggregation name, given by the user.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

scGenLinkAggregationBasePortGroupId 1.3.6.1.4.1.81.28.1.6.1.1.3
The slot/unit number of the Base Port for this Link Aggregation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenLinkAggregationBasePortId 1.3.6.1.4.1.81.28.1.6.1.1.4
The port number in the slot/unit of the Base Port for this Link Aggregation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scGenLinkAggregationNumberOfPorts 1.3.6.1.4.1.81.28.1.6.1.1.5
The current number of ports that belong to this Link Aggregation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenLinkAggregationLogicalPortGroupId 1.3.6.1.4.1.81.28.1.6.1.1.6
The slot number of the logical port, representing this Link Aggregation. All parameters for the LAG are managed through that logical port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenLinkAggregationLogicalPortId 1.3.6.1.4.1.81.28.1.6.1.1.7
The logical port number in the slot, representing this Link Aggregation. All parameters for the LAG are managed through that logical port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenLinkAggregationFunctionalStatus 1.3.6.1.4.1.81.28.1.6.1.1.8
The functional status of the LAG: ok(1) - fully functional LAG, transmitting and receiving packets on all its ports. fail(2) - all ports in the LAG are not in ok status. partialFail(3) - some of the ports in the LAG are not in ok status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), partialFail(3), notSupported(255)  

scGenLinkAggregationAutoNegResults 1.3.6.1.4.1.81.28.1.6.1.1.9
The auto-negotiation results for speed and duplex for the LAG ports: ok(1) - all ports resolved the same speed and duplex mode after auto-negotiation process. autoNegInconsistantResults(2) - not all ports resolved the same speed and duplex mode after auto-negotiation process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), autoNegInconsistantResults(2), notSupported(255)  

scGenLinkAggregationFaultMask 1.3.6.1.4.1.81.28.1.6.1.1.10
Each bit of this item describes the situation of the LAG regarding specific fault: bit 1: on indicates 'LAG connection lost' when scGenLinkAggregationFunctionalStatus=fail(2) bit 2: on indicates 'LAG partial connection' when scGenLinkAggregationFunctionalStatus=partailFail(3) bit 3: on indicates 'LAG auto-neg inconsistant results' when scGenLinkAggregationAutoNegResults= autoNegInconsistantResults(2)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

scGenLinkAggregationStatus 1.3.6.1.4.1.81.28.1.6.1.1.11
The status of this scGenLinkAggregation entry. According to RMON-2 standard (RFC 2021).
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

scGenPortIPAddressRsp 1.3.6.1.4.1.81.28.1.7
OBJECT IDENTIFIER    

scGenPortIPAddressRspTable 1.3.6.1.4.1.81.28.1.7.1
Table of attributes which define general configuration information about a single SC based port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScGenPortIPAddressRspEntry

scGenPortIPAddressRspEntry 1.3.6.1.4.1.81.28.1.7.1.1
An entry in the table, containing data about a single Port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScGenPortIPAddressRspEntry  

scGenPortIPAddressRspGroupId 1.3.6.1.4.1.81.28.1.7.1.1.1
Id of the group to which the port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortIPAddressRspPortId 1.3.6.1.4.1.81.28.1.7.1.1.2
Unique Id of the port in the scGenPortRspTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortIPAddressRspIpAddressIndex 1.3.6.1.4.1.81.28.1.7.1.1.3
Unique Id of the port in the scGenPortRspTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scGenPortIPAddressRspIpAddress 1.3.6.1.4.1.81.28.1.7.1.1.4
This MIB-item sets an IpAddress of a station that is connected to a port that performs RSP. A value of 0.0.0.0 in this Mib Item means that it does not describe an existing IpAddress. Default value is 0.0.0.0
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

scEth 1.3.6.1.4.1.81.28.2
OBJECT IDENTIFIER    

scEthPort 1.3.6.1.4.1.81.28.2.1
OBJECT IDENTIFIER    

scEthPortTable 1.3.6.1.4.1.81.28.2.1.1
Table of attributes which define configuration, performance and error information about ethernet ports based on the switchChip.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScEthPortEntry

scEthPortEntry 1.3.6.1.4.1.81.28.2.1.1.1
An entry in the table, containing data about a single port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScEthPortEntry  

scEthPortGroupId 1.3.6.1.4.1.81.28.2.1.1.1.1
Id of the group to which the port belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scEthPortId 1.3.6.1.4.1.81.28.2.1.1.1.2
Unique Id of the port in the scEthPortTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scEthPortOctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.3
The total number of good octets received and bad octets filtered by the port (excluding framing bits but including FCS octets). This item is the summation of scEthPortGoodOctetsRec and scEthPortBadOctets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.4
The total number of good packets received and bad packets filtered by the port. This item is the summation of scEthPortGoodPktsRec and scEthPortBadPkts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodBroadcastPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.5
The total number of good packets received that were directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodMulticastPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.6
The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortCRCAlignErrors 1.3.6.1.4.1.81.28.2.1.1.1.7
The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but were not an integral number of octets in length or had a bad Frame Check Sequence (FCS).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortOversizePkts 1.3.6.1.4.1.81.28.2.1.1.1.8
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortFragments 1.3.6.1.4.1.81.28.2.1.1.1.9
The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortJabber 1.3.6.1.4.1.81.28.2.1.1.1.10
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and were not an integral number of octets in length or had a bad Frame Check Sequence (FCS).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortCollisions 1.3.6.1.4.1.81.28.2.1.1.1.11
The best estimate of the total number of collisions on this Ethernet segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts64Octets 1.3.6.1.4.1.81.28.2.1.1.1.12
The total number of packets (including error packets) that were 64 octets in length (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts65to127Octets 1.3.6.1.4.1.81.28.2.1.1.1.13
The total number of packets (including error packets) that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts128to255Octets 1.3.6.1.4.1.81.28.2.1.1.1.14
The total number of packets (including error packets) that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts256to511Octets 1.3.6.1.4.1.81.28.2.1.1.1.15
The total number of packets (including error packets) that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts512to1023Octets 1.3.6.1.4.1.81.28.2.1.1.1.16
The total number of packets (including error packets) that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPkts1024to1518Octets 1.3.6.1.4.1.81.28.2.1.1.1.17
The total number of packets (including error packets) that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.18
The total number of good packets received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortBadPkts 1.3.6.1.4.1.81.28.2.1.1.1.19
The total number of bad packets filtered by the port. This item is the summation of: scEthPortCRCAlignErrors, scEthPortOversizePkts, scEthPortFragments and scEthPortJabber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodOctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.20
The total number of good octets of data received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortBadOctets 1.3.6.1.4.1.81.28.2.1.1.1.21
The total number of bad octets of data filtered by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodBroadcastOctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.22
The total number of good octets received that were directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodMulticastOctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.23
The total number of good octets received that were directed to a multicast address. Note that this number does not include octets directed to the broadcast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodOctetsSent 1.3.6.1.4.1.81.28.2.1.1.1.24
The total number of good octets of data sent by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodPktsSent 1.3.6.1.4.1.81.28.2.1.1.1.25
The total number of good packets sent by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortLateCollisions 1.3.6.1.4.1.81.28.2.1.1.1.26
The best estimate of the total number of late collisions on this Ethernet segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortFunctionalStatus 1.3.6.1.4.1.81.28.2.1.1.1.27
The functional status of the port: ok(1) - fully functional port, transmitting and receiving packets. rld(2) - receive link down condition on the port - Indicates a cable or connector failure detected by the port H/W. partition(8) - the port is in partition state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), rld(2), rxJabber(3), partition(8), remoteFault(10), rspError(11), notSupported(255)  

scEthPortMode 1.3.6.1.4.1.81.28.2.1.1.1.28
The flow control mode of the port when operated in full duplex: halfDuplex(1) - Half duplex connection, standard mode for segment fullDuplexNoPause(2) - Full duplex connection without exchanging flow control packets fullDuplexProprietaryFC(3) - Full duplex connection with Lucent's proprietary flow control frames exchanged fullDuplexISL(4) - Full duplex connection with ISL proprietary protocol control words for VLAN & priority exchanged, ISL = Inter-Switch-Link fullDuplexFlowControlISL(5) - Full duplex connection with both ISL proprietary protocol control words and flow control frames exchanged fullDuplexAsymTxPause(6) - Full duplex connection with STD 802.3x flow control frames sent from this port, but flow control packets received on it are not processed fullDuplexSymPause(7) - Full duplex connection with STD 802.3x flow control frames exchanged fullDuplexAsymRxPause(8) - Full duplex connection with no flow control frames sent from this port, but STD 802.3x flow control 0frames received on it are processed. For Giga ports, when auto-negotiation is enabled, the flow control mode is set internally according to auto-negotiation resolution; and access to this item is read-only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER halfDuplex(1), fullDuplexNoPause(2), fullDuplexProprietaryFC(3), fullDuplexISL(4), fullDuplexFlowControlISL(5), fullDuplexAsymTxPause(6), fullDuplexSymPause(7), fullDuplexAsymRxPause(8), notSupported(255)  

scEthPortSpeed 1.3.6.1.4.1.81.28.2.1.1.1.29
This parameter defines the port speed: ethernet(1) and fastEthernet(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(1), fastEthernet(2), gigabitEthernet(3), a155Mbps(4), a622Mbps(5), notSupported(255)  

scEthPortAutoNegotiation 1.3.6.1.4.1.81.28.2.1.1.1.30
This object define if the Auto Sense /Auto Negotiation process is enable(1) or disable (2) for modules that don't support the Auto Snese mode please define the notSupported option..
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scEthPortAutoNegotiationStatus 1.3.6.1.4.1.81.28.2.1.1.1.31
This object define the status of the Auto Negotiation process: pass: The Auto negotiation process was completed and succeeded . fail: The Auto Negotiation process failed . disable: The Auto Negotiation process is not enabled . notSupported: The Auto Negotiation feature is not available in this module .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pass(1), fail(2), disable(3), inProgress(4), notSupported(255)  

scEthPortTotalOctets 1.3.6.1.4.1.81.28.2.1.1.1.32
The total number of octets received and transmitted on the port (including all good and bad). This item is the summation of scEthPortOctetsRec and scEthPortGoodOctetsSent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortTotalPkts 1.3.6.1.4.1.81.28.2.1.1.1.33
The total number of packets received and transmitted on the port (including all good and bad). This item is the summation of scEthPortPktsRec and scEthPortGoodPktsSent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortDropEvents 1.3.6.1.4.1.81.28.2.1.1.1.34
The total number of events in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGigaPauseStatus 1.3.6.1.4.1.81.28.2.1.1.1.35
Indicates the status of the Flow Control as determined in the Auto Negotiation process on the Gigabit ports: noPause(1) indicates that there is no Flow Control. symmetricPause(2) indicates that both sides are working in Tx&Rx Flow Control. asymmetricPauseRx(3) indicates that both sides agreed on working in asynnetric Flow Control - TxOnly against RxOnly. If Giga Auto Neg is disabled, then noPause(1) is indicated when Flow Control is disabled, while symmetricPause(2) is indicated when Flow Control is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noPause(1), symmetricPause(2), asymmetricPauseRx(3), notSupported(255)  

scEthPortLower32OctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.36
Lower 32 bit conter of the total number of octets of data received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortUpper32OctetsRec 1.3.6.1.4.1.81.28.2.1.1.1.37
Upper 32 bit conter of the total number of octets of data received by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortLower32OctetsSent 1.3.6.1.4.1.81.28.2.1.1.1.38
Lower 32 bit conter of the total number of octets of data sent by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortUpper32OctetsSent 1.3.6.1.4.1.81.28.2.1.1.1.39
Upper 32 bit conter of the total number of octets of data sent by the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortGoodUnicastPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.40
The total number of good packets received that were directed to a unicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortDiscardPktsRec 1.3.6.1.4.1.81.28.2.1.1.1.41
The total number of packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortUnicastPktsSent 1.3.6.1.4.1.81.28.2.1.1.1.42
The total number of good packets sent by the port that were directed to a unicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortDiscardPktsSent 1.3.6.1.4.1.81.28.2.1.1.1.43
The total number of packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortPauseCapabilities 1.3.6.1.4.1.81.28.2.1.1.1.44
The Pause capabilities of a Giga port that should be advertised to the link partner when performing auto-negotiation: noFlowControl (1) - no flow control support in any direction asymTxFlowControlOnly (2) - STD 802.3x flow control frames can be sent from this port, but flow control packets received on it can not be processed. symFlowControlOnly (3) - STD 802.3x flow control frames must be supported in both directions symAndAsymRxFlowControl (4) - STD 802.3x flow control frames must be supported in both directions or at least received flowcontrol frames on this port can be processed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noFlowControl(1), asymTxFlowControlOnly(2), symFlowControlOnly(3), symAndAsymRxFlowControl(4), notSupported(255)  

scEthPortMulticastPktsSent 1.3.6.1.4.1.81.28.2.1.1.1.45
The total number of good packets sent by the port that were directed to a multicast address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortUndersizePktsRec 1.3.6.1.4.1.81.28.2.1.1.1.46
The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

scEthPortFlowControl 1.3.6.1.4.1.81.28.2.1.1.1.47
The flow control mode of the port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noFlowControl(1), asymTxFlowControl(2), symFlowControl(3), asymRxFlowControl(4), proprietaryFlowControl(5), notSupported(255)  

scEthGroup 1.3.6.1.4.1.81.28.2.2
OBJECT IDENTIFIER    

scEthGroupTable 1.3.6.1.4.1.81.28.2.2.1
Table of attributes which define ethernet configuration information about a single SC based group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScEthGroupEntry

scEthGroupEntry 1.3.6.1.4.1.81.28.2.2.1.1
An entry in the table, containing data about a single Group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScEthGroupEntry  

scEthGroupId 1.3.6.1.4.1.81.28.2.2.1.1.1
Unique Id of the group in the scEthGroupTable. Equals the number of the slot by which the group is accessed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scEthGroupAutoPartitionEnable 1.3.6.1.4.1.81.28.2.2.1.1.2
Enables/Disables the Auto-Partition mechanism in all ports of this module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

scEthGroupFefiEnable 1.3.6.1.4.1.81.28.2.2.1.1.3
This item enables\disables the FEFI mechanism of all Fast-Ethernet PHY's in the module. It enables\disables both the transmission and the recognition of FEFI signals.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), notSupported(255)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor