ZHONE-COM-VOICE-SIG-MIB
File:
ZHONE-COM-VOICE-SIG-MIB.mib (14991 bytes)
Imported modules
Imported symbols
Defined Values
zhoneVoiceSignalingMib |
1.3.6.1.4.1.5504.4.3.7 |
The Zhone Voice Signaling MIB defines Zhone Voice Signaling specfic
information.
This MIB contains system side voice specific info, like the
hookflash timers.
User will not create this profile, but when system comes up, it checks
to see if the scalar info exists. If not, it creates one with
default values. |
MODULE-IDENTITY |
|
|
|
zhoneVoiceSignalingTimers |
1.3.6.1.4.1.5504.4.3.7.1 |
This is a place holder to contain all the system wide voice specific
timers.
'hookFlashTimerMin' field is read/write field so a user can set this
field to a particular value. It specifies the minimum timer for
hookflash.
'hookFlashTimerMax' field is a read/write field to a user can set this
field to a particular value. It specifies the maximum timer for
hookflash. |
Status: current |
Access: read-only |
OBJECT-IDENTITY |
|
|
|
hookFlashTimerMin |
1.3.6.1.4.1.5504.4.3.7.1.1 |
The Hookflash specifies the minimum timer that qualifies for a
hookflash. Any loopopen below this time will be ignored as a
glitch. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..2147483647 |
|
hookFlashTimerMax |
1.3.6.1.4.1.5504.4.3.7.1.2 |
The Hookflash specifies the maximum timer that qualifies for a
hookflash. Any loopopen more than this timer will be considered
as a onhook. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..2147483647 |
|
sysPartialDialTo |
1.3.6.1.4.1.5504.4.3.7.1.3 |
This object contains the maximum value of the partial dial
time out. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysCriticalDialTo |
1.3.6.1.4.1.5504.4.3.7.1.4 |
This object contains the maximum value of the critical \
dial time out. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysBusyToneTo |
1.3.6.1.4.1.5504.4.3.7.1.5 |
This object contains the default timeout value for
busy tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysDialToneTo |
1.3.6.1.4.1.5504.4.3.7.1.6 |
This object contains the default timeout value for
dial tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysMsgWaitToneTo |
1.3.6.1.4.1.5504.4.3.7.1.7 |
This object contains the default timeout value for
message wait tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysOffhookWarnToneTo |
1.3.6.1.4.1.5504.4.3.7.1.8 |
This object contains the default timeout value for
offhook warn tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysRingingTo |
1.3.6.1.4.1.5504.4.3.7.1.9 |
This object contains the default timeout value for
ringing. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysRingbackTo |
1.3.6.1.4.1.5504.4.3.7.1.10 |
This object contains the default timeout value for
ringback tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysReorderToneTo |
1.3.6.1.4.1.5504.4.3.7.1.11 |
This object contains the default timeout value for
reorder tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysStutterToneTo |
1.3.6.1.4.1.5504.4.3.7.1.12 |
This object contains the default timeout value for
stutter tone. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysServerMaxTimer |
1.3.6.1.4.1.5504.4.3.7.1.13 |
This object is used as part of a retransmission
algorithm when communicating with a call agent.
This object contains the maximum time in seconds
since the sending of the initial datagram to a
call agent. If more than pktcNcsEndPntConfigTSMax
time has elapsed, the endpoint becomes disconnected. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysConfigMax1 |
1.3.6.1.4.1.5504.4.3.7.1.14 |
This object contains the suspicious error threshold
for signaling messages. The configMax1 object
indicates the retransmission threshold at which
the gateway MAY actively query the domain name server
(DNS) in order to detect the possible change of
call agent interfaces. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysConfigMax2 |
1.3.6.1.4.1.5504.4.3.7.1.15 |
This object contains the disconnect error threshold
for signaling messages. The configMax2 object
indicates the retransmission threshold at which
the gateway SHOULD contact the DNS one more time
to see if any other interfaces to the call agent
have become available. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysMax1Enable |
1.3.6.1.4.1.5504.4.3.7.1.16 |
This object enables/disables the Max1 domain name
server (DNS) query operation when the configMax1
threshold has been reached. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
sysMax2Enable |
1.3.6.1.4.1.5504.4.3.7.1.17 |
This object enables/disables the Max2 domain name
server (DNS) query operation when the configMax2
threshold has been reached. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
sysMaxWaitingDelay |
1.3.6.1.4.1.5504.4.3.7.1.18 |
Maximum Waiting Delay (MWD) contains the maximum
number of seconds a Gateway waits after powering
on, before initiating the restart procedure with
the call agent. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysDisconnectWaitTimer |
1.3.6.1.4.1.5504.4.3.7.1.19 |
This object contains the initial number of seconds
the gateway waits after a disconnect, before
initiating the disconnected procedure with the
call agent. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysDisconnectMinTimer |
1.3.6.1.4.1.5504.4.3.7.1.20 |
This object contains the minimum number of seconds
the gatway waits after a disconnect, before
initiating the disconnected procedure with the
call agent. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysDisconnectMaxTimer |
1.3.6.1.4.1.5504.4.3.7.1.21 |
This object contains the maximum number of seconds
the gatway waits after a disconnect, before
initiating the disconnected procedure with the
call agent. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysMaxRetransmitTimer |
1.3.6.1.4.1.5504.4.3.7.1.22 |
This object contains the maximum number of seconds
for the retransmission timer. When this timer
expires the gateway retransmits the message. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysInitRetransmitTimer |
1.3.6.1.4.1.5504.4.3.7.1.23 |
This object contains the initial number of seconds
for the retransmission timer. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysKeepAliveTimer |
1.3.6.1.4.1.5504.4.3.7.1.24 |
Specifies a timeout value in minutes for sending
long duration call notification message. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysNoResponseTimer |
1.3.6.1.4.1.5504.4.3.7.1.25 |
Timeout period in seconds before no response is declared. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysCallWaitMaxRepeat |
1.3.6.1.4.1.5504.4.3.7.1.26 |
This object contains the default value of the
maximum number of repetitions of the call waiting
tone that the gateway will play. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysCallWaitDelay |
1.3.6.1.4.1.5504.4.3.7.1.27 |
This object contains the delay between repetitions
of the call waiting tone that the gateway will play. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
sysMinMakePulseWidth |
1.3.6.1.4.1.5504.4.3.7.1.29 |
This is the minimum make pulse width for the dial pulse. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
20..200 |
|
sysMaxMakePulseWidth |
1.3.6.1.4.1.5504.4.3.7.1.30 |
This is the maximum make pulse width for the dial pulse. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
20..200 |
|
sysMinBreakPulseWidth |
1.3.6.1.4.1.5504.4.3.7.1.31 |
This is the minimum break pulse width for the dial pulse. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
20..200 |
|
sysMaxBreakPulseWidth |
1.3.6.1.4.1.5504.4.3.7.1.32 |
This is the maximum break pulse width for the dial pulse. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
20..200 |
|