ZHONE-INTERFACE-TRANSLATION-MIB

File: ZHONE-INTERFACE-TRANSLATION-MIB.mib (47048 bytes)

Imported modules

IANAifType-MIB IF-MIB SNMPv2-SMI
SNMPv2-TC Zhone Zhone-TC

Imported symbols

IANAifType ifEntry InterfaceIndex
Integer32 Unsigned32 OBJECT-TYPE
MODULE-IDENTITY OBJECT-IDENTITY NOTIFICATION-TYPE
TruthValue zhoneInterfaceTranslation zhoneShelfIndex
zhoneSlotIndex zhoneModules ZhoneShelfValue
ZhoneSlotValue ZhoneRowStatus ZhoneIfType

Defined Types

PhysicalToIfIndexEntry  
SEQUENCE    
  pportIndex Integer32
  subPortIndex Integer32
  zhoneIfIndex InterfaceIndex
  xxxifTypexxx IANAifType

IfIndexToPhysicalEntry  
SEQUENCE    
  zhoneShelfNumber ZhoneShelfValue
  zhoneSlotNumber ZhoneSlotValue
  pportNumber Integer32
  subPortNumber Integer32
  ifaceType IANAifType
  ifaceTypeExtension ZhoneIfType

IfStackDefaultEntry  
SEQUENCE    
  ifStkDefCardType Integer32
  ifStkDefUpperType IANAifType
  ifStkDefLowerType IANAifType
  ifStkDefUnits Integer32
  ifStkDefAdminStatus INTEGER
  ifStkDefRowStatus ZhoneRowStatus

IfInverseStackEntry  
SEQUENCE    
  ifInverseStackLowerLayer InterfaceIndex
  ifInverseStackHigherLayer InterfaceIndex
  ifInverseStackStatus INTEGER

ZhoneIfXEntry  
SEQUENCE    
  physicalFlag TruthValue
  ifTypeExtension ZhoneIfType
  redundancyParam1 Integer32
  zhoneIfXEntryIfTypeAlias IANAifType
  zhoneIfXEntryRowStatus ZhoneRowStatus
  zhoneIfXEntryShelfAlias Integer32
  zhoneIfXEntrySlotAlias Integer32
  zhoneIfXEntryPortAlias Integer32
  zhoneIfXEntrySubportAlias Integer32
  zhoneIfXDescriptionIndex Integer32

ZhonePhysicalToIfIndexEntry  
SEQUENCE    
  zhonePortIndex Integer32
  zhoneSubPortIndex Integer32
  zhoneIfType IANAifType
  zhoneIfTypeExtension ZhoneIfType
  zhonePhysicalIfIndex InterfaceIndex

ZhoneDescriptionEntry  
SEQUENCE    
  zhoneDescriptionRowStatus ZhoneRowStatus
  zhoneDescriptionText OCTET STRING

ZhoneLineRedStatusEntry  
SEQUENCE    
  zhoneLineRedStatusFunction INTEGER
  zhoneLineRedOpStatus INTEGER

Defined Values

zhoneInterfaceTrans 1.3.6.1.4.1.5504.6.6
Defines translation tables that provide the translation to and from shelf/slot/port/subport <-> interface number. Both table are created whenever an ifIndex is created. The ifStackDefaultTable is used to provide a roadmap of stack bindings, and to supply default ifAdminStatus values for new rows of the ifTable.
MODULE-IDENTITY    

ifIndexNext 1.3.6.1.4.1.5504.3.5.1
Contains the next available ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

physicalToIfIndexTable 1.3.6.1.4.1.5504.3.5.2
Table to translate from shelf/slot/physical port/subport to the interface number (zhoneIfIndex). The physical port is the port number on the card selected by shelf/slot. The role of subport may vary depending on the card type, but is included to allow maximum flexibility and future exhancements. This table has been replaced by a zhonePhysicalToIfIndexTable. The objects in this table have been replaced by zhonePortIndex, zhoneSubPortIndex, zhonePhysicalIfIndex, zhoneIfType, and zhoneIfTypeExtension.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PhysicalToIfIndexEntry

physicalToIfIndexEntry 1.3.6.1.4.1.5504.3.5.2.1
The physical table is indexed by shelf/slot/physical port /subport. In instances where there is no subport the value of subport should be set to zero. This entry has been replaced by zhonePhysicalToIfIndexEntry.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  PhysicalToIfIndexEntry  

pportIndex 1.3.6.1.4.1.5504.3.5.2.1.1
The port number of the physical port on the card or device. The numbering should start at 1 for the first port on the device and proceed sequentially. This object has been replaced by zhonePortIndex.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

subPortIndex 1.3.6.1.4.1.5504.3.5.2.1.2
This entry provides flexibility to define more than one interface on a port. The most common use of subport will be to handle structured TDM lines allowing for example an interface number to be assign to each DS1 in a DS3. Subport may also be used to handle other situations where a physical port contains more than one inetrface. This object has replaced by zhoneSubPortIndex.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

zhoneIfIndex 1.3.6.1.4.1.5504.3.5.2.1.3
The interface number of the pport or pport/subport that uniquely identifies the interface across the system. This object has been replaced by zhonePhysicalIfIndex.
Status: deprecated Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

xxxifTypexxx 1.3.6.1.4.1.5504.3.5.2.1.4
The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention. This object has replaced by zhoneIfType.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IANAifType  

ifIndexToPhysicalTable 1.3.6.1.4.1.5504.3.5.3
Table to translate from interface number (zhoneIfIndex) to the physical location and port (including subport where defined). zhoneShelfNumber is the number of the shelf on which the port is located and can have a value from 1-255, zhoneSlotNumber is the card slot on which card with the physical port is located and currently has a value of 1-18. The pportNumber identifies the specific physical port on the card beginning with port 1. subPortNumber issued to define multiple interfaces on a port as required, if the identified port has a single interface number, subport will be set to zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfIndexToPhysicalEntry

ifIndexToPhysicalEntry 1.3.6.1.4.1.5504.3.5.3.1
The table is indexed by the zhoneIfidndex of the desired interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfIndexToPhysicalEntry  

zhoneShelfNumber 1.3.6.1.4.1.5504.3.5.3.1.1
The zhoneShelfNumber is the physical address or number of the shelf for the desired interface. A Zhone system is limited to a maximum of 255 shelves. The first shelf in a system is shelf 1,
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneShelfValue  

zhoneSlotNumber 1.3.6.1.4.1.5504.3.5.3.1.2
The zhoneSlotNumber is the physical slot number on which the card containing the port or interface is located. Zhone shelves are currently limited to 30 slots numbered 1-30. Note that daughter boards do not have slot numbers.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneSlotValue  

pportNumber 1.3.6.1.4.1.5504.3.5.3.1.3
The pportNumber defines the phyiscal port number on the selected shelf/slot (card). Port numbering begins with port 1 and ports are numbered sequentially. pportNumber 0 is invalid unless the ifIndex is for an interface that is not bound to a physical port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

subPortNumber 1.3.6.1.4.1.5504.3.5.3.1.4
The subPortNumber is used to identify multiple logical ports on a physical that require their own interface number, e.g. DS1s on a DS3 port. Note that multiple protocol layers such as IP over ATM do not require unique interface numbers and are handled by the standard ifStackTable mechanism. Subport 0 is reserved to designate that a physical port has no subport and hence a single interface number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

ifaceType 1.3.6.1.4.1.5504.3.5.3.1.5
The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.
Status: current Access: read-only
OBJECT-TYPE    
  IANAifType  

ifaceTypeExtension 1.3.6.1.4.1.5504.3.5.3.1.6
This field is used to specify the zhone-proprietary interface type when necessary. For example, if the interface is a line-group, iftype is set to 'IANAIFTYPE_OTHER' and ifTypeExtension is set to 'ZHONEIFTYPE_LINEGROUP'. By default ifTypeExtension is set to 'ZHONEIFTYPE_NONE(0)'.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneIfType  

ifStackDefaultTable 1.3.6.1.4.1.5504.3.5.4
This table defines the default ifTable vales and stack arrangements (bindings) and unit numbers based on types of cards and ifTypes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfStackDefaultEntry

ifStackDefaultEntry 1.3.6.1.4.1.5504.3.5.4.1
This table contains the unit/card type, the ifType of the 'from' layer (ifStkDefUpperIfType) and the ifType of the 'to' layer (ifStkDefLowerIfType) and the number of units for each association. Also the Default value ifAdminStatus in ifTable. A value must be supplied for all fields except ifStkDefAdminStatus to create a new row.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfStackDefaultEntry  

ifStkDefCardType 1.3.6.1.4.1.5504.3.5.4.1.1
The numerical representation of unit/card type as specified in zhoneCardResourcesModule where cardZhoneType has the following defined values: unknownType(1), interShelf(2), infoServices(3), hdsl2(10),sechtor100(1001),zedge64(2001), and zplex10(3001). Other values may be used.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

ifStkDefUpperType 1.3.6.1.4.1.5504.3.5.4.1.2
The value of ifType corresponding to the higher sublayer of the relationship, i.e., the sublayer that runs on top of the sublayer identified by the corresponding instance of ifStkDefLowerType.
Status: current Access: not-accessible
OBJECT-TYPE    
  IANAifType  

ifStkDefLowerType 1.3.6.1.4.1.5504.3.5.4.1.3
The value of ifType corresponding to the default lower sublayer of the relationship, i.e., the sublayer that runs under the sublayer identified by the corresponding instance of ifStkDefUpperType.
Status: current Access: not-accessible
OBJECT-TYPE    
  IANAifType  

ifStkDefUnits 1.3.6.1.4.1.5504.3.5.4.1.4
Number of units for this association which indicates the number of ifindexes created for this particular iftype pair on this card type such as 48 creations for the initial version of the HDSL2 card.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

ifStkDefAdminStatus 1.3.6.1.4.1.5504.3.5.4.1.5
Default value for ifAdminStatus in ifTable for the UPPPER ifindex associated with the ifStkDefUpperType.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

ifStkDefRowStatus 1.3.6.1.4.1.5504.3.5.4.1.6
Row status used to create and/or remove rows from this table.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

ifInverseStackTable 1.3.6.1.4.1.5504.3.5.5
This is the inverse ifstacktable in that the index scheme is lower.higher as opposed to higher.lower as defined in rfc2233. Comments and information is copied here for clarity. Information on a particular relationship between two sub-layers, specifying that one sub-layer runs on 'top' of the other sub-layer. Each sub-layer corresponds to a conceptual row in the ifTable. Use of this table is solely for management stations to walk the table (getnext) from the lower physical port (ifindex) up the stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfInverseStackEntry

ifInverseStackEntry 1.3.6.1.4.1.5504.3.5.5.1
The table containing information on the relationships between the multiple sub-layers of network interfaces. In particular, it contains information on which sub- layers run 'on top of' which other sub-layers, where each sub-layer corresponds to a conceptual row in the ifTable. For example, when the sub-layer with ifIndex value x runs over the sub-layer with ifIndex value y, then this table contains: ifStackStatus.y.x=active For each ifIndex value, I, which identifies an active interface, there are always at least two instantiated rows in this table associated with I. For one of these rows, I is the value of ifStackHigherLayer; for the other, I is the value of ifStackLowerLayer. (If I is not involved in multiplexing, then these are the only two rows associated with I.) For example, two rows exist even for an interface which has no others stacked on top or below it: ifStackStatus.0.x=active ifStackStatus.x.0=active A corresponding entry in this mib is made whenever an entry is made in the standard ifStackTable. Thus, deletion, creation, and modification is not possible on this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfInverseStackEntry  

ifInverseStackLowerLayer 1.3.6.1.4.1.5504.3.5.5.1.1
The value of ifIndex corresponding to the lower sub- layer of the relationship, i.e., the sub-layer which runs 'below' the sub-layer identified by the corresponding instance of ifInverseStackHigherLayer. If there is no lower sub-layer, then this object has the value 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ifInverseStackHigherLayer 1.3.6.1.4.1.5504.3.5.5.1.2
The value of ifIndex corresponding to the higher sub-layer of the relationship, i.e., the sub-layer which runs on 'top' of the sub-layer identified by the corresponding instance of ifStackLowerLayer. If there is no higher sub-layer (below the internetwork layer), then this object has the value 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ifInverseStackStatus 1.3.6.1.4.1.5504.3.5.5.1.3
Status of this entry. If the entry exists, this value must be 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1)  

zhoneIfXTable 1.3.6.1.4.1.5504.3.5.6
This table contains additional objects for the interface table. Each row corresponds to a conceptual row in the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZhoneIfXEntry

zhoneIfXEntry 1.3.6.1.4.1.5504.3.5.6.1
An entry containing additional management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZhoneIfXEntry  

physicalFlag 1.3.6.1.4.1.5504.3.5.6.1.1
The flag is set to 'true(1)' if the ifIndex represents the physical layer. Otherwise the flag is set to 'false(2)'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

ifTypeExtension 1.3.6.1.4.1.5504.3.5.6.1.2
This field is used to specify the zhone-proprietary interface type when necessary. For example, if the interface is a line-group, iftype is set to 'IANAIFTYPE_OTHER' and ifTypeExtension is set to 'ZHONEIFTYPE_LINEGROUP'. By default ifTypeExtension is set to 'ZHONEIFTYPE_NONE(0)'.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneIfType  

redundancyParam1 1.3.6.1.4.1.5504.3.5.6.1.3
For linegroups, this value contains information about line redundancy as follows: 0x8000 bit set => switchover on failure 0x7FFF number of seconds to wait before switchover 0x40000000 bit set => revert after switchover 0x3FFF0000 these 4 bits contains the number of seconds to wait before reverting 0x80000000 bit set => disable transmit on standby For physical interfaces: 0x00000001 bit set => secondary member of a protection pair bit clear => primary member, or standalone
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -2147483648..2147483647  

zhoneIfXEntryIfTypeAlias 1.3.6.1.4.1.5504.3.5.6.1.4
This object maps to ifType object within the ifEntry table. This object is used when creating a new row in the ifEntry table since ifType is read-only.
Status: current Access: read-create
OBJECT-TYPE    
  IANAifType  

zhoneIfXEntryRowStatus 1.3.6.1.4.1.5504.3.5.6.1.5
This object is used to create and delete rows within the ifEntry table since ifEntry is standard and does not have a Row Status object. Currently, only ifType value of 'other' is allowed to be created via SNMP.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

zhoneIfXEntryShelfAlias 1.3.6.1.4.1.5504.3.5.6.1.6
Writeable shelf number. This object maps to the read-only object zhoneShelfNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..1  

zhoneIfXEntrySlotAlias 1.3.6.1.4.1.5504.3.5.6.1.7
Writeable slot number. This object maps to the read-only object zhoneSlotNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..33  

zhoneIfXEntryPortAlias 1.3.6.1.4.1.5504.3.5.6.1.8
Writeable port number. This object maps to the read-only object zhonePortNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

zhoneIfXEntrySubportAlias 1.3.6.1.4.1.5504.3.5.6.1.9
Writeable subport number. This object maps to the read-only object zhoneSubPortNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

zhoneIfXDescriptionIndex 1.3.6.1.4.1.5504.3.5.6.1.10
Index value of a zhoneDescriptionEntry. Zero indicates no reference to zhoneDescriptionEntry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

zhonePhysicalToIfIndexTable 1.3.6.1.4.1.5504.3.5.7
Table to translate from shelf/slot/physical port/subport/ iftype/iftype-extension to the interface number (zhonePhysicalIfIndex). The physical port is the port number on the card selected by shelf/slot. The role of subport may vary depending on the card type, but is included to allow maximum flexibility and future exhancements. Iftype-extension is searched when iftype is set to 'ZHONEIFTYPE_NONE(0)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZhonePhysicalToIfIndexEntry

zhonePhysicalToIfIndexEntry 1.3.6.1.4.1.5504.3.5.7.1
The physical table is indexed by shelf/slot/physical port /subport/iftype/iftype-extension. In instances where there is no subport the value of subport should be set to zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZhonePhysicalToIfIndexEntry  

zhonePortIndex 1.3.6.1.4.1.5504.3.5.7.1.1
The port number of the physical port on the card or device. The numbering should start at 1 for the first port on the device and proceed sequentially.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

zhoneSubPortIndex 1.3.6.1.4.1.5504.3.5.7.1.2
This entry provides flexibility to define more than one interface on a port. The most common use of subport will be to handle structured TDM lines allowing for example an interface number to be assign to each DS1 in a DS3. Subport may also be used to handle other situations where a physical port contains more than one inetrface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

zhoneIfType 1.3.6.1.4.1.5504.3.5.7.1.4
The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.
Status: current Access: not-accessible
OBJECT-TYPE    
  IANAifType  

zhoneIfTypeExtension 1.3.6.1.4.1.5504.3.5.7.1.5
This field is used to specify the zhone-proprietary interface type when necessary. For example, if the interface is a line-group, iftype is set to 'IANAIFTYPE_OTHER' and ifTypeExtension is set to 'ZHONEIFTYPE_LINEGROUP'. By default ifTypeExtension is set to 'ZHONEIFTYPE_NONE(0)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZhoneIfType  

zhonePhysicalIfIndex 1.3.6.1.4.1.5504.3.5.7.1.6
The interface number of the pport or pport/subport that uniquely identifies the interface across the system.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

zhoneDescriptionTable 1.3.6.1.4.1.5504.3.5.8
Table of description entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZhoneDescriptionEntry

zhoneDescriptionEntry 1.3.6.1.4.1.5504.3.5.8.1
Descritpion entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZhoneDescriptionEntry  

zhoneDescriptionRowStatus 1.3.6.1.4.1.5504.3.5.8.1.1
Row status object.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

zhoneDescriptionText 1.3.6.1.4.1.5504.3.5.8.1.2
Description object used as free format text description. Contains readable characters, with the following exclusions: 1. Double quotes 2. Carriage Returns 3. Line Feeds 4. Carat Maximum number of characters is 64, including any NULL terminator.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

zhoneIfXDescriptionIndexNext 1.3.6.1.4.1.5504.3.5.9
Returns the next available zhoneIfXDescriptionIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

zhoneLineRedStatusTable 1.3.6.1.4.1.5504.3.5.10
Line redundancy information
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZhoneLineRedStatusEntry

zhoneLineRedStatusEntry 1.3.6.1.4.1.5504.3.5.10.1
Line redundancy information for on line
Status: current Access: not-accessible
OBJECT-TYPE    
  ZhoneLineRedStatusEntry  

zhoneLineRedStatusFunction 1.3.6.1.4.1.5504.3.5.10.1.1
Current redundancy function as returned from LineRR. . inactive means registered but neither active nor standby . standby means this is the protection line in a pair. . active means either standalone or the working line in a protection pair. . unavailable means not registered with LineRR
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), standby(2), active(3), unavailable(4)  

zhoneLineRedOpStatus 1.3.6.1.4.1.5504.3.5.10.1.2
Line status . active means line is up as standalone or the working line in a redundant pair. . oos means line is down . trafficDisabled means up as standby . unavailable means not registered with LineRR
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), oos(2), trafficDisabled(3), unavailable(4)  

zhoneLineRedTraps 1.3.6.1.4.1.5504.3.5.11
Traps for facility redundancy
Status: current Access: read-only
OBJECT-IDENTITY    

zhoneLineRedTrapsPrefix 1.3.6.1.4.1.5504.3.5.11.0
Add zero in OID for traps.
Status: current Access: read-only
OBJECT-IDENTITY    

zhoneLineRedundancyUnsafe 1.3.6.1.4.1.5504.3.5.11.0.1
Sent when configured peer is not traffic-disabled
Status: current Access: read-only
NOTIFICATION-TYPE    

zhoneLineRedundancySafe 1.3.6.1.4.1.5504.3.5.11.0.2
Sent when both lines in a facility-redundant pair have become redundancy ready.
Status: current Access: read-only
NOTIFICATION-TYPE