ZTE-AN-OPTICAL-MODULE-MIB

File: ZTE-AN-OPTICAL-MODULE-MIB.mib (53214 bytes)

Imported modules

SNMPv2-TC	SNMPv2-SMI	IF-MIB
ZTE-AN-SMI

Imported symbols

TEXTUAL-CONVENTION	RowStatus	DisplayString
MODULE-IDENTITY	OBJECT-TYPE	Integer32
NOTIFICATION-TYPE	ifIndex	ifAdminStatus
ifOperStatus	ifType	zxAnInterface

Defined Types

ZxAnOpticalModuleAlmPrfEntry
SEQUENCE
	zxAnOpticalModuleAlmPrfName	DisplayString
	zxAnOpticalRxPwrLowerThresh	Integer32
	zxAnOpticalRxPwrUpperThresh	Integer32
	zxAnOpticalTxPwrLowerThresh	Integer32
	zxAnOpticalTxPwrUpperThresh	Integer32
	zxAnOpticalBiasCurrLowerThresh	Integer32
	zxAnOpticalBiasCurrUpperThresh	Integer32
	zxAnOpticalVoltageLowerThresh	Integer32
	zxAnOpticalVoltageUpperThresh	Integer32
	zxAnOpticalTempLowerThresh	Integer32
	zxAnOpticalTempUpperThresh	Integer32
	zxAnOpticalOfflineTrapEnable	INTEGER
	zxAnOpticalModuleConfClass	DisplayString
	zxAnOpticalModuleAlmPrfRowStatus	RowStatus

ZxAnOpticalAlmPrfIfConfEntry
SEQUENCE
	zxAnOpticalIfAlmPrf	DisplayString

ZxAnOpticalModuleInfoEntry
SEQUENCE
	zxAnOpticalIfRxPwrCurrValue	Integer32
	zxAnOpticalIfTxPwrCurrValue	Integer32
	zxAnOpticalIfRate	Integer32
	zxAnOpticalBiasCurrent	Integer32
	zxAnOpticalSupplyVoltage	Integer32
	zxAnOpticalWavelength	Integer32
	zxAnOpticalTemperature	Integer32
	zxAnOpticalFiberType	INTEGER
	zxAnOpticalVersionLevel	DisplayString
	zxAnOpticalVendorPn	DisplayString
	zxAnOpticalVendorName	DisplayString
	zxAnOpticalVendorSn	DisplayString
	zxAnOpticalProductionDate	DisplayString
	zxAnOpticalModuleType	DisplayString
	zxAnOpticalFiberInterfaceType	DisplayString
	zxAnOpticalMaterialNumber	OCTET STRING
	zxAnOpticalRegisterData	OCTET STRING
	zxAnOpticalOtdrSupport	INTEGER
	zxAnOpticalModuleActualClass	DisplayString
	zxAnOpticalOtdrVersion	DisplayString
	zxAnOpticalTransDistanceSmLongR	Integer32
	zxAnOpticalTransDistanceSmShortR	Integer32
	zxAnOpticalTransDistanceOm1	Integer32
	zxAnOpticalTransDistanceOm2	Integer32
	zxAnOpticalTransDistanceOm3	Integer32
	zxAnOpticalTransDistanceCopper	Integer32
	zxAnOpticalPartNumber	DisplayString

ZxAnOpticalAlsIfConfEntry
SEQUENCE
	zxAnOptAlsEnable	INTEGER
	zxAnOptAlsLaserLosDuration	Integer32
	zxAnOptAlsLaserShutdownDuration	Integer32
	zxAnOptAlsLaserStartUpDuration	Integer32

ZxAnOpticalModuleConfEntry
SEQUENCE
	zxAnOpticalModuleConfVendorName	DisplayString
	zxAnOpticalModuleConfVendorPn	DisplayString
	zxAnOpticalModuleConfiguredClass	DisplayString
	zxAnOpticalModuleConfProperty	INTEGER
	zxAnOpticalModuleConfTechNorms	DisplayString
	zxAnOpticalModuleConfRowStatus	RowStatus

ZxAnOpticalModuleChanInfoEntry
SEQUENCE
	zxAnOpticalChanLaserSwitch	INTEGER
	zxAnOpticalChanWavelength	Integer32
	zxAnOpticalChanCurrTxPwr	Integer32
	zxAnOpticalChanBiasCurrent	Integer32

ZxAnOpticalModuleClassValueEntry
SEQUENCE
	zxAnOpticalModuleClassId	Integer32
	zxAnOpticalModuleClassValue	DisplayString

Defined Values

zxAnOpticalModuleMib		1.3.6.1.4.1.3902.1082.30.40
This MIB defines zte Access Node managed objects.
MODULE-IDENTITY

zxAnOpticalModuleGlobalObjects		1.3.6.1.4.1.3902.1082.30.40.1
OBJECT IDENTIFIER

zxAnOpticalModuleObjects		1.3.6.1.4.1.3902.1082.30.40.2
OBJECT IDENTIFIER

zxAnOpticalModuleNotifications		1.3.6.1.4.1.3902.1082.30.40.3
OBJECT IDENTIFIER

zxAnOpticalModuleConformance		1.3.6.1.4.1.3902.1082.30.40.4
OBJECT IDENTIFIER

zxAnOpticalModuleCapabilities		1.3.6.1.4.1.3902.1082.30.40.1.1
The optical module management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. opticalModuleConfClass (0): value 1 means zxAnOpticalModuleConfClass is supported. opticalAlarmPrfUnit(1): value 1 means some objects in the zxAnOpticalModuleAlmPrfTable will use the new unit, for more information, please see the description of the object in the zxAnOpticalModuleAlmPrfTable. opticalModuleConfTechNorms(2): value 1 means zxAnOpticalModuleConfTechNorms is supported. NOTE: No recommended to display it in NMS.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	opticalModuleConfClass(0), opticalAlarmPrfUnit(1), opticalModuleConfTechNorms(2)

zxAnOptModuleIfShutdownUnplugEn		1.3.6.1.4.1.3902.1082.30.40.1.2
Indicates whether the zxAnOpticalModuleUnpluggedAlm should be generated when the port the optical module plugged in has been shutdown. enabled(1) : The zxAnOpticalOfflineTrapEnable indicates whether the zxAnOpticalModuleUnpluggedAlm should be generated or not. disabled(2): The zxAnOpticalModuleUnpluggedAlm should not be generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnOptModuleFstUnpluggedRptEn		1.3.6.1.4.1.3902.1082.30.40.1.3
Indicates whether the zxAnOpticalModuleUnpluggedAlm should be generated when the agent has detected the optical module is offline for the first time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnOpticalModuleAlmPrfTable		1.3.6.1.4.1.3902.1082.30.40.2.2
This table includes the optical module threshold profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalModuleAlmPrfEntry

zxAnOpticalModuleAlmPrfEntry		1.3.6.1.4.1.3902.1082.30.40.2.2.1
An entry in zxAnOpticalModuleAlmPrfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalModuleAlmPrfEntry

zxAnOpticalModuleAlmPrfName		1.3.6.1.4.1.3902.1082.30.40.2.2.1.1
A textual string containing information about the optical module alarm threshold profile name .
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnOpticalRxPwrLowerThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.2
The lower limit threshold on input optical power. The alarm should be generated when zxAnOpticalIfRxPwrCurrValue is lower than this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

zxAnOpticalRxPwrUpperThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.3
The upper limit threshold on input optical power. The alarm should be generated when zxAnOpticalIfRxPwrCurrValue exceeds this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

zxAnOpticalTxPwrLowerThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.4
The lower limit threshold on output optical power. The alarm should be generated when zxAnOpticalIfTxPwrCurrValue is lower than this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

zxAnOpticalTxPwrUpperThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.5
The upper limit threshold on output optical power. The alarm should be generated when zxAnOpticalIfTxPwrCurrValue exceeds this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

zxAnOpticalBiasCurrLowerThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.6
The lower limit threshold on optical modules bias current.The alarm should be generated when zxAnOpticalBiasCurrent is lower than this threshold. The unit is 1mA when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1mA.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..1500

zxAnOpticalBiasCurrUpperThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.7
The upper limit threshold on optical modules bias current. The alarm should be generated when zxAnOpticalBiasCurrent exceeds this threshold. The unit is 1mA when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1mA.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..1500

zxAnOpticalVoltageLowerThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.8
The lower limit threshold on optical modules supply voltage. The alarm should be generated when zxAnOpticalSupplyVoltage is lower than this threshold. The unit is 1 Volt when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1 Volt.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

zxAnOpticalVoltageUpperThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.9
The upper limit threshold on optical modules supply voltage. The alarm should be generated when zxAnOpticalSupplyVoltage exceeds this threshold. The unit is 1 Volt when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1 Volt.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

zxAnOpticalTempLowerThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.10
The lower limit threshold on optical modules temperature. The alarm should be generated when zxAnOpticalTemperature is lower than this threshold.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-50..100

zxAnOpticalTempUpperThresh		1.3.6.1.4.1.3902.1082.30.40.2.2.1.11
The upper limit threshold on optical modules temperature. The alarm should be generated when zxAnOpticalTemperature exceeds this threshold.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-50..100

zxAnOpticalOfflineTrapEnable		1.3.6.1.4.1.3902.1082.30.40.2.2.1.12
Indicates whether optical module is online/offline traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnOpticalModuleConfClass		1.3.6.1.4.1.3902.1082.30.40.2.2.1.13
The optical module configured class.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnOpticalModuleAlmPrfRowStatus		1.3.6.1.4.1.3902.1082.30.40.2.2.1.50
The row status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnOpticalAlmPrfIfConfTable		1.3.6.1.4.1.3902.1082.30.40.2.3
This table includes the optical module profile configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalAlmPrfIfConfEntry

zxAnOpticalAlmPrfIfConfEntry		1.3.6.1.4.1.3902.1082.30.40.2.3.1
An entry in zxAnOpticalAlmPrfIfConfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalAlmPrfIfConfEntry

zxAnOpticalIfAlmPrf		1.3.6.1.4.1.3902.1082.30.40.2.3.1.2
A textual string containing information about the optical module alarm threshold profile name .
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnOpticalModuleInfoTable		1.3.6.1.4.1.3902.1082.30.40.2.4
This table includes the optical module information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalModuleInfoEntry

zxAnOpticalModuleInfoEntry		1.3.6.1.4.1.3902.1082.30.40.2.4.1
An entry in zxAnOpticalModuleInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalModuleInfoEntry

zxAnOpticalIfRxPwrCurrValue		1.3.6.1.4.1.3902.1082.30.40.2.4.1.2
The optical power monitored at the input.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalIfTxPwrCurrValue		1.3.6.1.4.1.3902.1082.30.40.2.4.1.3
The optical power monitored at the output.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalIfRate		1.3.6.1.4.1.3902.1082.30.40.2.4.1.4
The optical module interface rate.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalBiasCurrent		1.3.6.1.4.1.3902.1082.30.40.2.4.1.5
The optical module bias current .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalSupplyVoltage		1.3.6.1.4.1.3902.1082.30.40.2.4.1.6
The optical module supply voltage.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalWavelength		1.3.6.1.4.1.3902.1082.30.40.2.4.1.7
The optical module wavelength.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTemperature		1.3.6.1.4.1.3902.1082.30.40.2.4.1.8
The optical module temperature .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalFiberType		1.3.6.1.4.1.3902.1082.30.40.2.4.1.9
The optical module Fiber Type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singleMode(1), multiMode(2), unknown(3)

zxAnOpticalVersionLevel		1.3.6.1.4.1.3902.1082.30.40.2.4.1.10
The optical module vendor Level.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

zxAnOpticalVendorPn		1.3.6.1.4.1.3902.1082.30.40.2.4.1.11
The optical module vendor P/N.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

zxAnOpticalVendorName		1.3.6.1.4.1.3902.1082.30.40.2.4.1.12
The optical module vendor name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnOpticalVendorSn		1.3.6.1.4.1.3902.1082.30.40.2.4.1.13
The optical module vendor sn.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

zxAnOpticalProductionDate		1.3.6.1.4.1.3902.1082.30.40.2.4.1.14
The optical module production date.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

zxAnOpticalModuleType		1.3.6.1.4.1.3902.1082.30.40.2.4.1.15
The optical module type.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

zxAnOpticalFiberInterfaceType		1.3.6.1.4.1.3902.1082.30.40.2.4.1.16
The optical fiber interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

zxAnOpticalMaterialNumber		1.3.6.1.4.1.3902.1082.30.40.2.4.1.17
The material number of pin(A2).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..20)

zxAnOpticalRegisterData		1.3.6.1.4.1.3902.1082.30.40.2.4.1.18
The optical module data is from register.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..128)

zxAnOpticalOtdrSupport		1.3.6.1.4.1.3902.1082.30.40.2.4.1.19
The OTDR is supported by the optical module or not. supported(1): The optical module supports OTDR. unsupported(2): The optical module doesn't support OTDR. unknown(255): Whether the optical module supports OTDR is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	supported(1), unsupported(2), unknown(255)

zxAnOpticalModuleActualClass		1.3.6.1.4.1.3902.1082.30.40.2.4.1.20
The optical module actual class.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnOpticalOtdrVersion		1.3.6.1.4.1.3902.1082.30.40.2.4.1.21
The optical module OTDR software version. If the optical module doesn't support OTDR or the OTDR has no software version, this object will be set to an empty string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

zxAnOpticalTransDistanceSmLongR		1.3.6.1.4.1.3902.1082.30.40.2.4.1.40
This value specifies the transfer distance that is supported by the transceiver while operating in compliance with the applicable standards using single mode based long reach fiber. The value is in units of kilometers. A value of 255 means the transceiver supports a transfer distance greater than 254 km. A value of zero means the transceiver does not support single mode fiber or that the transfer distance information must be determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTransDistanceSmShortR		1.3.6.1.4.1.3902.1082.30.40.2.4.1.41
This value specifies the transfer distance that is supported by the transceiver while operating in compliance with the applicable standards using single mode based short reach fiber. The value is in units of 100 meters. A value of 255 means the transceiver supports a transfer distance greater than 25.4 km. A value of zero means the transceiver does not support single mode fiber or that the transfer distance information must be determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTransDistanceOm1		1.3.6.1.4.1.3902.1082.30.40.2.4.1.42
This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 62.5 micron multimode OM1(200 MHzkm at 850nm, 500MHzkm at 1310mm) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the transfer distance must determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTransDistanceOm2		1.3.6.1.4.1.3902.1082.30.40.2.4.1.43
This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 50 micron multimode OM2(500 MHz*km at 850nm) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support OM2 fiber or the transfer distance must determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTransDistanceOm3		1.3.6.1.4.1.3902.1082.30.40.2.4.1.44
This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 50 micron multimode OM3(2000 MHz*km) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support OM3 fiber or the transfer distance must determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalTransDistanceCopper		1.3.6.1.4.1.3902.1082.30.40.2.4.1.45
This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using copper cable. For active cable, this value represents actual length. The value is in units of 1 meter. A value of 255 means that the transceiver supports a transfer distance greater than 254m. A value of zero means that the transceiver does not support copper or active cables or the transfer distance must determined from the transceiver technology.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalPartNumber		1.3.6.1.4.1.3902.1082.30.40.2.4.1.48
The optical module part number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnOpticalAlsIfConfTable		1.3.6.1.4.1.3902.1082.30.40.2.5
This table includes the ALS configuration of the optical module.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalAlsIfConfEntry

zxAnOpticalAlsIfConfEntry		1.3.6.1.4.1.3902.1082.30.40.2.5.1
An entry in zxAnOpticalAlsIfConfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalAlsIfConfEntry

zxAnOptAlsEnable		1.3.6.1.4.1.3902.1082.30.40.2.5.1.1
Enable or disable the ALS function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnOptAlsLaserLosDuration		1.3.6.1.4.1.3902.1082.30.40.2.5.1.2
This attribute specifies the value of the LOS duration. The laser will be shutdown when detected the LOS duration longer than zxAnOptAlsLaserLosDuration value. Setting this object will enable the ALS function. For C300 Series NE, the default value is 5. For C600 Series NE, the default value is 50.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..200000

zxAnOptAlsLaserShutdownDuration		1.3.6.1.4.1.3902.1082.30.40.2.5.1.3
This attribute specifies the value of the laser shutdown duration. Setting this object will enable the ALS function.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..200000

zxAnOptAlsLaserStartUpDuration		1.3.6.1.4.1.3902.1082.30.40.2.5.1.4
This attribute specifies the value of the laser re-open duration. Setting this object will enable the ALS function.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..200000

zxAnOpticalModuleConfTable		1.3.6.1.4.1.3902.1082.30.40.2.6
This table includes the optical module configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalModuleConfEntry

zxAnOpticalModuleConfEntry		1.3.6.1.4.1.3902.1082.30.40.2.6.1
An entry in zxAnOpticalModuleConfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalModuleConfEntry

zxAnOpticalModuleConfVendorName		1.3.6.1.4.1.3902.1082.30.40.2.6.1.1
The optical module vendor name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnOpticalModuleConfVendorPn		1.3.6.1.4.1.3902.1082.30.40.2.6.1.2
The optical module vendor P/N.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..64)

zxAnOpticalModuleConfiguredClass		1.3.6.1.4.1.3902.1082.30.40.2.6.1.3
The optical module configured class. Includes the following: GPON/B+, GPON/C+, GPON/EC+, XGPON1/N1, XGPON1/N2a, EPON/PX20+, 10G-EPON/PRX30, 10G-EPON/PR30, GPON/D, XGS-PON/N1, XGS-PON/N2, XG-PON&GPON_COMBO/N1-B+, XG-PON&GPON_COMB0/N2-C+, GPON-OTDR/C+.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnOpticalModuleConfProperty		1.3.6.1.4.1.3902.1082.30.40.2.6.1.4
The property of the table record. default: the default record, it can't be modified or deleted by the user. userDefined: the user-defined record.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	default(1), userDefined(2)

zxAnOpticalModuleConfTechNorms		1.3.6.1.4.1.3902.1082.30.40.2.6.1.11
The optical module configured technical norms.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnOpticalModuleConfRowStatus		1.3.6.1.4.1.3902.1082.30.40.2.6.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnLacpAggEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnOpticalModuleChanInfoTable		1.3.6.1.4.1.3902.1082.30.40.2.10
This table includes the optical module channel information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalModuleChanInfoEntry

zxAnOpticalModuleChanInfoEntry		1.3.6.1.4.1.3902.1082.30.40.2.10.1
An entry in zxAnOpticalModuleChanInfoTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalModuleChanInfoEntry

zxAnOpticalChanLaserSwitch		1.3.6.1.4.1.3902.1082.30.40.2.10.1.1
Enables or disables the laser function of the optical module channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	open(1), close(2)

zxAnOpticalChanWavelength		1.3.6.1.4.1.3902.1082.30.40.2.10.1.2
The wavelength of the optical module channel.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalChanCurrTxPwr		1.3.6.1.4.1.3902.1082.30.40.2.10.1.3
The transmitted power of the optical module channel.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalChanBiasCurrent		1.3.6.1.4.1.3902.1082.30.40.2.10.1.4
The bias current of the optical module channel.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxAnOpticalModuleClassValueTable		1.3.6.1.4.1.3902.1082.30.40.2.20
This table includes the optical module class value. NOTE: No recommended to develop this function in EMS.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnOpticalModuleClassValueEntry

zxAnOpticalModuleClassValueEntry		1.3.6.1.4.1.3902.1082.30.40.2.20.1
An entry in zxAnOpticalModuleClassValueTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnOpticalModuleClassValueEntry

zxAnOpticalModuleClassId		1.3.6.1.4.1.3902.1082.30.40.2.20.1.1
The optical module class id.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..256

zxAnOpticalModuleClassValue		1.3.6.1.4.1.3902.1082.30.40.2.20.1.2
The optical module class value.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..64)

zxAnOptRxPwrUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.1
It indicates that zxAnOpticalIfRxPwrCurrValue is below the zxAnOpticalRxPwrLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptRxPwrUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.2
zxAnOptRxPwrUnderThreshAlm clear
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptRxPwrOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.3
It indicates that zxAnOpticalIfRxPwrCurrValue is exceeds the zxAnOpticalRxPwrUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptRxPwrOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.4
zxAnOptPwrRxOverThreshAlarm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTxPwrUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.5
It indicates that zxAnOpticalIfTxPwrCurrValue is below the zxAnOpticalTxPwrLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTxPwrUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.6
zxAnOptPwrTxUnderThreshAlarm clear
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTxPwrOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.7
It indicates that zxAnOpticalIfTxPwrCurrValue is exceeds the zxAnOpticalTxPwrUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTxPwrOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.8
zxAnOptPwrTxOverThreshAlarm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptBiasCurrUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.9
It indicates that zxAnOpticalBiasCurrent is below the zxAnOpticalBiasCurrLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptBiasCurrUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.10
zxAnOptBiasCurrUnderThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptBiasCurrOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.11
It indicates that zxAnOpticalBiasCurrent is over the zxAnOpticalBiasCurrUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptBiasCurrOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.12
zxAnOptBiasCurrOverThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptVoltageUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.13
It indicates that zxAnOpticalSupplyVoltage is below the zxAnOpticalVoltageLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptVoltageUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.14
zxAnOptVoltageUnderThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptVoltageOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.15
It indicates that zxAnOpticalSupplyVoltage is over the zxAnOpticalVoltageUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptVoltageOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.16
zxAnOptVoltageOverThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTempUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.17
It indicates that zxAnOpticalTemperature is below the zxAnOpticalTempLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTempUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.18
zxAnOptTempUnderThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTempOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.19
It indicates that zxAnOpticalTemperature is over the zxAnOpticalTempUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptTempOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.20
zxAnOptTempOverThreshAlm clear.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOpticalModuleUnpluggedAlm		1.3.6.1.4.1.3902.1082.30.40.3.21
The alarm occurred when optical module is not online.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOpticalModuleUnpluggedClr		1.3.6.1.4.1.3902.1082.30.40.3.22
The alarm restore when optical module is online.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptModuleClassMismatchAlm		1.3.6.1.4.1.3902.1082.30.40.3.23
A zxAnOptModuleClassMismatchAlm trap is sent when the agent has detected that the optical module has plugged in, but zxAnOpticalModuleConfClass is not same as zxAnOpticalModuleActualClass.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptModuleClassMismatchClr		1.3.6.1.4.1.3902.1082.30.40.3.24
A zxAnOptModuleClassMismatchClr trap is sent when the agent has detected that the optical module has plugged in, and zxAnOpticalModuleConfClass is same as zxAnOpticalModuleActualClass.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanTxPwrUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.51
A zxAnOptChanTxPwrUnderThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanCurrTxPwr has been less than the zxAnOpticalTxPwrLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanTxPwrUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.52
A zxAnOptChanTxPwrUnderThreshClr trap is sent when the zxAnOptChanTxPwrUnderThreshAlm is cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanTxPwrOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.53
A zxAnOptChanTxPwrOverThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanCurrTxPwr has been exceeded the zxAnOpticalTxPwrUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanTxPwrOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.54
A zxAnOptChanTxPwrOverThreshClr trap is sent when the zxAnOptChanTxPwrOverThreshAlm is cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanBiasUnderThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.55
A zxAnOptChanBiasUnderThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanBiasCurrent has been less than the zxAnOpticalBiasCurrLowerThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanBiasUnderThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.56
A zxAnOptChanBiasCurrUnderThreshClr trap is sent when the zxAnOptChanBiasUnderThreshAlm is cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanBiasOverThreshAlm		1.3.6.1.4.1.3902.1082.30.40.3.57
A zxAnOptChanBiasOverThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanBiasCurrent has been exceeded the zxAnOpticalBiasCurrUpperThresh.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptChanBiasOverThreshClr		1.3.6.1.4.1.3902.1082.30.40.3.58
A zxAnOptChanBiasOverThreshClr trap is sent when the zxAnOptChanBiasOverThreshAlm is cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptEponGponMismatchAlm		1.3.6.1.4.1.3902.1082.30.40.3.59
A zxAnOptEponGponMismatchAlm trap is sent when the agent has detected that the GPON optical module is plugged in the EPON port or the EPON optical module is plugged in the GPON port.
Status: current	Access: read-only
NOTIFICATION-TYPE

zxAnOptEponGponMismatchClr		1.3.6.1.4.1.3902.1082.30.40.3.60
A zxAnOptEponGponMismatchClr trap is sent when the zxAnOptEponGponMismatchAlm is cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE