ZTE-AN-PORT-IDENTIFICATION-PROFILE-MIB

File: ZTE-AN-PORT-IDENTIFICATION-PROFILE-MIB.mib (42331 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	ZTE-AN-SMI	ZTE-AN-IF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	MODULE-COMPLIANCE	OBJECT-GROUP
NOTIFICATION-GROUP	RowStatus	TruthValue
DisplayString	TEXTUAL-CONVENTION	ifIndex
zxAnServiceSecurity	zxAnSubIfIndex

Defined Types

ZxAnAccessLoopTagType
A set of access loop characteristics defined in TR-101 about DSL line, each bit refers to a suboption: Bit 00 : Suboption81, actual data rate upstream. Bit 01 : Suboption82, actual data rate downstream. Bit 02 : Suboption83, minimum data rate upstream. Bit 03 : Suboption84, minimum data rate downstream. Bit 04 : Suboption85, attainable data rate upstream. Bit 05 : Suboption86, attainable data rate downstream. Bit 06 : Suboption87, maximum data rate upstream. Bit 07 : Suboption88, maximum data rate downstream. Bit 08 : Suboption89, minimum data rate upstream in low power state. Bit 09 : Suboption8A, minimum data rate downstream in low power state. Bit 10 : Suboption8B, maximum interleaving delay upstream. Bit 11 : Suboption8C, actual interleaving delay upstream. Bit 12 : Suboption8D, maximum interleaving delay downstream. Bit 13 : Suboption8E, actual interleaving delay downstream. Bit 14 : Suboption90, data link type protocol.
TEXTUAL-CONVENTION
	BITS	suboption81(0), suboption82(1), suboption83(2), suboption84(3), suboption85(4), suboption86(5), suboption87(6), suboption88(7), suboption89(8), suboption8A(9), suboption8B(10), suboption8C(11), suboption8D(12), suboption8E(13), suboption90(14)

ZxAnPortIdFormatPrfEntry
SEQUENCE
	zxAnPortIdFormatPrfName	DisplayString
	zxAnPortIdFormatPrfRowStatus	RowStatus

ZxAnPortIdCircuitIdSyntaxEntry
SEQUENCE
	zxAnPortIdCidComponentIndex	Integer32
	zxAnPortIdCidComponentType	INTEGER
	zxAnPortIdCidComponentId	Integer32
	zxAnPortIdCidComponentWidth	Integer32
	zxAnPortIdCidComponentString	DisplayString
	zxAnPortIdCidComponentProfile	DisplayString
	zxAnPortIdCidComponentRowStatus	RowStatus

ZxAnPortIdOperatorPrfEntry
SEQUENCE
	zxAnPortIdOperPrfName	DisplayString
	zxAnPortIdOperPonFormatPrf	DisplayString
	zxAnPortIdOperLanFormatPrf	DisplayString
	zxAnPortIdOperDhcpV4L2RAEnable	INTEGER
	zxAnPortIdOperDhcpV4L2RATrust	TruthValue
	zxAnPortIdOperDhcpV4L2RAPolicy	INTEGER
	zxAnPortIdOperDhcpV4AlcTag	ZxAnAccessLoopTagType
	zxAnPortIdOperDhcpV6L2RAEnable	INTEGER
	zxAnPortIdOperDhcpV6L2RATrust	TruthValue
	zxAnPortIdOperDhcpV6L2RAPolicy	INTEGER
	zxAnPortIdOperDhcpV6AlcTag	ZxAnAccessLoopTagType
	zxAnPortIdOperPppoeIAEnable	INTEGER
	zxAnPortIdOperPppoeIATrust	TruthValue
	zxAnPortIdOperPppoeIAPolicy	INTEGER
	zxAnPortIdOperPppoeAlcTag	ZxAnAccessLoopTagType
	zxAnPortIdOperDhcpV6L2RAWorkMode	INTEGER
	zxAnPortIdOperDhcpV4RidEnable	INTEGER
	zxAnPortIdOperDhcpV4RidFormatPrf	DisplayString
	zxAnPortIdOperDhcpV6RidEnable	INTEGER
	zxAnPortIdOperDhcpV6RidFormatPrf	DisplayString
	zxAnPortIdOperPppoeRidEnable	INTEGER
	zxAnPortIdOperPppoeRidFormatPrf	DisplayString
	zxAnPortIdOperPrfRowStatus	RowStatus

ZxAnPortIdVlanOperPrfConfEntry
SEQUENCE
	zxAnPortIdVid	Integer32
	zxAnPortIdVlanOperPrf	DisplayString
	zxAnPortIdVlanOperPrfRowStatus	RowStatus

ZxAnPortIdIfOperPrfConfEntry
SEQUENCE
	zxAnPortIdIfOperPrf	DisplayString
	zxAnPortIdIfOperPrfRowStatus	RowStatus

Defined Values

zxAnPortIdentificationProfileMib		1.3.6.1.4.1.3902.1082.70.67
The MIB module for the management of port identification profile configuration.
MODULE-IDENTITY

zxAnPortIdPrfGlobalObjects		1.3.6.1.4.1.3902.1082.70.67.1
OBJECT IDENTIFIER

zxAnPortIdPrfObjects		1.3.6.1.4.1.3902.1082.70.67.2
OBJECT IDENTIFIER

zxAnPortIdSystemConfMode		1.3.6.1.4.1.3902.1082.70.67.1.1
The port identification configuration mode of the system. The following is the explanation of each value of variable zxAnPortIdSystemConfMode. - normal(1): the efficient configuration of port identification operation is which configured under the interface mode, not by profile. - profile(2): the efficient configuration of port identification operation is which configured by operator profile. The operator profile is global applied, or applied in the interface, or applied in the VLAN. The default value of variable zxAnPortIdSystemConfMode in each project maybe different. C6XX only support profile(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), profile(2)

zxAnPortIdGlobalOperatorPrf		1.3.6.1.4.1.3902.1082.70.67.1.2
The operator profile name of port identification which is global configured. Size of the attribute is zero means not configured.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnPortIdCapabilities		1.3.6.1.4.1.3902.1082.70.67.1.3
The port identifacation capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. - dhcpV6L2RAWorkMode(0): value 1 means supporting zxAnPortIdOperDhcpV6L2RAWorkMode. - portIdOperLanFormatPrf(1): value 1 means supporting zxAnPortIdOperLanFormatPrf. - portIdOperDslDeprecated(2): value 1 means unsupporting zxAnPortIdOperAtmFormatPrf, zxAnPortIdOperPtmEtherFormatPrf, zxAnPortIdOperDhcpV4AlcTag, zxAnPortIdOperPppoeAlcTag, zxAnPortIdOperRelaySessionId, zxAnPortIdOperPppMaxPayLoad, zxAnPortIdOperDslfIwfPppoe, zxAnPortIdIfConfAlcEnable. - portIdOperRidConf(3): value 1 means supporting zxAnPortIdOperDhcpV4RidEnable, zxAnPortIdOperDhcpV4RidFormatPrf, zxAnPortIdOperDhcpV6RidEnable, zxAnPortIdOperDhcpV6RidFormatPrf, zxAnPortIdOperPppoeRidEnable, zxAnPortIdOperPppoeRidFormatPrf. - portIdOperAlcTagConf(4): value 1 means supporting zxAnPortIdOperDhcpV4AlcTag, zxAnPortIdOperPppoeAlcTag, zxAnPortIdOperDhcpV6AlcTag, regardless of portIdOperDslDeprecated.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	dhcpV6L2RAWorkMode(0), portIdOperLanFormatPrf(1), portIdOperDslDeprecated(2), portIdOperRidConf(3), portIdOperAlcTagConf(4)

zxAnPortIdFormatPrfTable		1.3.6.1.4.1.3902.1082.70.67.2.2
This table contains information of the port identification format profile configuration. One entry in this table reflects a format profile defined by a manager.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnPortIdFormatPrfEntry

zxAnPortIdFormatPrfEntry		1.3.6.1.4.1.3902.1082.70.67.2.2.1
An entry in zxAnPortIdFormatPrfTable, which is indexed by the zxAnPortIdFormatPrfName. To create a format profile, variable zxAnPortIdFormatPrfRowStatus must be included in one SNMP set operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnPortIdFormatPrfEntry

zxAnPortIdFormatPrfName		1.3.6.1.4.1.3902.1082.70.67.2.2.1.1
A port identification format profile name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdFormatPrfRowStatus		1.3.6.1.4.1.3902.1082.70.67.2.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnPortIdFormatPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnPortIdCircuitIdSyntaxTable		1.3.6.1.4.1.3902.1082.70.67.2.3
This table is to provide circuit ID syntax configuration. One entry in this table reflects a syntax item define by a manager, which is a component of a port identification format profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnPortIdCircuitIdSyntaxEntry

zxAnPortIdCircuitIdSyntaxEntry		1.3.6.1.4.1.3902.1082.70.67.2.3.1
An entry in zxAnPortIdCircuitIdSyntaxTable, which is index by the zxAnPortIdFormatPrfName and zxAnPortIdCidComponentIndex. If zxAnPortIdCidComponentType is standardVar(1) or extendedVar(2), zxAnPortIdCidComponentString can not be configured. If zxAnPortIdCidComponentType is separator(3), zxAnPortIdCidComponentWidth and zxAnPortIdCidComponentString can not be configured. If zxAnPortIdCidComponentType is userDefinedString(4), zxAnPortIdCidComponentId,zxAnPortIdCidComponentWidth can not be configured. After an entry is created, all variables can not be modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnPortIdCircuitIdSyntaxEntry

zxAnPortIdCidComponentIndex		1.3.6.1.4.1.3902.1082.70.67.2.3.1.1
A key that identifies a component in the circuit ID syntax of a port identification format profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..30

zxAnPortIdCidComponentType		1.3.6.1.4.1.3902.1082.70.67.2.3.1.2
An attribute that identifies the type of this component. The following types are possible: standardVar - A TR-101 based variable(1: access node id, 2: chassis, 3: rack, 4: frame, 5: slot, 6: sub-slot, 7: port, 8: vpi, 9: vci, 10: q-vid, 11: ethernet-priority) extendedVar - A proprietary variable(1: onu id, 2: gemPort, 3: cvlan, 4: svlan, 5: sn, 6: loid, 7: loidpw, 8: onu-number, 9: onu-info, 10: access-mode, 11: access-node-type, 12: xpi, 13: xci, 14: vport, 15: user-defined-cid, 16:src-mac, 17: onu-name, 18: user-defined-rid) separator - A delimiter (6: space) userDefinedString - Information configured by the network operator.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	standardVar(1), extendedVar(2), separator(3), userDefinedString(4)

zxAnPortIdCidComponentId		1.3.6.1.4.1.3902.1082.70.67.2.3.1.3
A unique and content sensitive identifier for the specific definition of this component. The following identifiers are expected: - A row number in table 2 of TR-101 (R-126). - An index into a proprietary managed entity that specifies possible proprietary variables. - An index into a proprietary managed entity that specifies possible constant character strings.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

zxAnPortIdCidComponentWidth		1.3.6.1.4.1.3902.1082.70.67.2.3.1.4
The width of the port identification circuit ID syntax component. If the length of component is less than the width then fill zero in front of the component. Value 0 means unconfigured.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..5

zxAnPortIdCidComponentString		1.3.6.1.4.1.3902.1082.70.67.2.3.1.5
Information configured by the network operator.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..50)

zxAnPortIdCidComponentProfile		1.3.6.1.4.1.3902.1082.70.67.2.3.1.6
At present, this object is the syntax profile of the ONU information. It is supported when the component is onu-info (when zxAnPortIdCidComponentType is extendedVar(2) and zxAnPortIdCidComponentType is onu-info(9)). The profile is also defined in zxAnPortIdFormatPrfTable.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnPortIdCidComponentRowStatus		1.3.6.1.4.1.3902.1082.70.67.2.3.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnPortIdCircuitIdSyntaxEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnPortIdOperatorPrfTable		1.3.6.1.4.1.3902.1082.70.67.2.4
This table contains information of the port identification operator profile configuration. One entry in this table reflects a operator profile defined by a manager.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnPortIdOperatorPrfEntry

zxAnPortIdOperatorPrfEntry		1.3.6.1.4.1.3902.1082.70.67.2.4.1
An entry in zxAnPortIdOperatorPrfTable, which is indexed by the zxAnPortIdOperPrfName. To create an operator profile, variable zxAnPortIdOperPrfRowStatus must be included in one SNMP set operation. After an entry is created, other variables in the table can be modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnPortIdOperatorPrfEntry

zxAnPortIdOperPrfName		1.3.6.1.4.1.3902.1082.70.67.2.4.1.1
A port identification operator profile name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdOperPonFormatPrf		1.3.6.1.4.1.3902.1082.70.67.2.4.1.4
Format profile of port identification applied while the access node type is pon.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdOperLanFormatPrf		1.3.6.1.4.1.3902.1082.70.67.2.4.1.5
Format profile of port identification applied while the access node type is PTP.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdOperDhcpV4L2RAEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.11
The operator profile switch used to activate or deactivate interface DHCPv4 layer-2 relay agent. There are two states: - enabled: the DHCPv4 layer-2 relay agent is activated. - disabled: the DHCPv4 layer-2 relay agent is deactivated.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperDhcpV4L2RATrust		1.3.6.1.4.1.3902.1082.70.67.2.4.1.12
DHCPv4 layer-2 relay agent trust flag of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperDhcpV4L2RAPolicy.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

zxAnPortIdOperDhcpV4L2RAPolicy		1.3.6.1.4.1.3902.1082.70.67.2.4.1.13
DHCPv4 layer-2 relay agent trust policy of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperDhcpV4L2RATrust. In addition, a manager must comply with the following rules: - when trust flag is true, policy can be set to keep or replace, - when trust flag is false, policy can be set to discard or add.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	keep(1), replace(2), discard(3), add(4)

zxAnPortIdOperDhcpV4AlcTag		1.3.6.1.4.1.3902.1082.70.67.2.4.1.14
Access loop characteristics of DHCPv4 supported by this operator profile. The bit value 1 means the suboption represented by this bit is supported. It used only by DHCPv4.
Status: current	Access: read-create
OBJECT-TYPE
	ZxAnAccessLoopTagType

zxAnPortIdOperDhcpV6L2RAEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.21
The operator profile switch used to activate or deactivate interface DHCPv6 layer-2 relay agent. There are two states: - enabled: the DHCPv6 layer-2 relay agent is activated. - disabled: the DHCPv6 layer-2 relay agent is deactivated.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperDhcpV6L2RATrust		1.3.6.1.4.1.3902.1082.70.67.2.4.1.22
DHCPv6 layer-2 relay agent trust flag of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperDhcpV6L2RAPolicy.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

zxAnPortIdOperDhcpV6L2RAPolicy		1.3.6.1.4.1.3902.1082.70.67.2.4.1.23
DHCPv6 layer-2 relay agent trust policy of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperDhcpV6L2RATrust. In addition, a manager must comply with the following rules: - when trust flag is true, policy can be set to keep or replace, - when trust flag is false, policy can be set to discard or add.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	keep(1), replace(2), discard(3), add(4)

zxAnPortIdOperDhcpV6AlcTag		1.3.6.1.4.1.3902.1082.70.67.2.4.1.24
Access loop characteristics of DHCPv6 supported by this operator profile. The bit value 1 means the suboption represented by this bit is supported. It used by DHCPv6 at relay mode.
Status: current	Access: read-create
OBJECT-TYPE
	ZxAnAccessLoopTagType

zxAnPortIdOperPppoeIAEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.31
The operator profile switch used to activate or deactivate interface PPPoE intermediate agent. There are two states: - enabled: the PPPoE intermediate agent is activated. - disabled: the PPPoE intermediate agent is deactivated.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperPppoeIATrust		1.3.6.1.4.1.3902.1082.70.67.2.4.1.32
PPPoE intermediate agent trust flag of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperPppoeIAPolicy.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

zxAnPortIdOperPppoeIAPolicy		1.3.6.1.4.1.3902.1082.70.67.2.4.1.33
PPPoE intermediate agent trust policy of the operator profile. To set this variable, it must be in one SNMP set operation together with variable zxAnPortIdOperPppoeIATrust. In addition, a manager must comply with the following rules: - when trust flag is true, policy can be set to keep or replace, - when trust flag is false, policy can be set to discard or add.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	keep(1), replace(2), discard(3), add(4)

zxAnPortIdOperPppoeAlcTag		1.3.6.1.4.1.3902.1082.70.67.2.4.1.34
Access loop characteristics of PPPoE supported by this operator profile. The bit value 1 means the suboption represented by this bit is supported.It used by PPPoE and PPPoA.
Status: current	Access: read-create
OBJECT-TYPE
	ZxAnAccessLoopTagType

zxAnPortIdOperDhcpV6L2RAWorkMode		1.3.6.1.4.1.3902.1082.70.67.2.4.1.38
DHCPv6 layer 2 relay agent work mode of the profile. LDRA means the protocol RFC6221(Lightweight DHCPv6 Relay Agent). noLdra: The format of the relay messages do not meet RFC6221 standards. ldra: The format of the relay messages meet RFC6221 standards. invalid: The format of the relay message is configured by zxAnDhcpV6L2RAWorkMode.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	noLdra(1), ldra(2), invalid(255)

zxAnPortIdOperDhcpV4RidEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.40
The operator profile switch used to enable or disable remote ID while the protocol type is DHCPv4.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperDhcpV4RidFormatPrf		1.3.6.1.4.1.3902.1082.70.67.2.4.1.41
Format profile of remote ID applied while the protocol type is DHCPv4.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnPortIdOperDhcpV6RidEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.42
The operator profile switch used to enable or disable remote ID while the protocol type is DHCPv6.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperDhcpV6RidFormatPrf		1.3.6.1.4.1.3902.1082.70.67.2.4.1.43
Format profile of remote ID applied while the protocol type is DHCPv6.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnPortIdOperPppoeRidEnable		1.3.6.1.4.1.3902.1082.70.67.2.4.1.44
The operator profile switch used to enable or disable remote ID while the protocol type is PPPoE.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

zxAnPortIdOperPppoeRidFormatPrf		1.3.6.1.4.1.3902.1082.70.67.2.4.1.45
Format profile of remote ID applied while the protocol type is PPPoE.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

zxAnPortIdOperPrfRowStatus		1.3.6.1.4.1.3902.1082.70.67.2.4.1.100
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnPortIdOperatorPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnPortIdVlanOperPrfConfTable		1.3.6.1.4.1.3902.1082.70.67.2.5
This table is to provide the VLAN operator profile configuration. One entry in this table reflects an operator profile has been applied to one VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnPortIdVlanOperPrfConfEntry

zxAnPortIdVlanOperPrfConfEntry		1.3.6.1.4.1.3902.1082.70.67.2.5.1
An entry in zxAnPortIdVlanOperPrfConfTable, which is indexed by the zxAnPortIdVid. To create an entry, variables zxAnPortIdVlanOperPrf and zxAnPortIdVlanOperPrfRowStatus must be included in one SNMP set operation. After an entry is created, variable zxAnPortIdVlanOperPrf can be modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnPortIdVlanOperPrfConfEntry

zxAnPortIdVid		1.3.6.1.4.1.3902.1082.70.67.2.5.1.1
The VLAN to which an operator profile of port identification can be applied.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

zxAnPortIdVlanOperPrf		1.3.6.1.4.1.3902.1082.70.67.2.5.1.2
A port identification operator profile name.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdVlanOperPrfRowStatus		1.3.6.1.4.1.3902.1082.70.67.2.5.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnPortIdVlanOperPrfConfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnPortIdIfOperPrfConfTable		1.3.6.1.4.1.3902.1082.70.67.2.6
This table is to provide the interface operator profile configuration. One entry in this table reflects an operator profile has been applied to an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZxAnPortIdIfOperPrfConfEntry

zxAnPortIdIfOperPrfConfEntry		1.3.6.1.4.1.3902.1082.70.67.2.6.1
An entry in zxAnPortIdIfOperPrfConfTable, which is indexed by the ifindex and zxAnSubIfIndex. To create an entry, variables zxAnPortIdIfOperPrf and zxAnPortIdIfOperPrfRowStatus must be included in one SNMP set operation. After an entry is created, variable zxAnPortIdIfOperPrf can be modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZxAnPortIdIfOperPrfConfEntry

zxAnPortIdIfOperPrf		1.3.6.1.4.1.3902.1082.70.67.2.6.1.1
A port identification operator profile name.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..32)

zxAnPortIdIfOperPrfRowStatus		1.3.6.1.4.1.3902.1082.70.67.2.6.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnPortIdIfOperPrfConfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zxAnPortIdPrfConformance		1.3.6.1.4.1.3902.1082.70.67.4
OBJECT IDENTIFIER

zxAnPortIdPrfCompliances		1.3.6.1.4.1.3902.1082.70.67.4.1
OBJECT IDENTIFIER

zxAnPortIdPrfGroups		1.3.6.1.4.1.3902.1082.70.67.4.2
OBJECT IDENTIFIER

zxAnPortIdPrfCompliance		1.3.6.1.4.1.3902.1082.70.67.4.1.1
The compliance statement for entities which implement the ZTE-AN-PORT-IDENTIFICATION-PROFILE-MIB.
Status: current	Access: read-create
MODULE-COMPLIANCE

zxAnPortIdSystemConfModeGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.1
A collection of objects providing information of port identification configuration mode in the system.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdGlobalOperatorPrfGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.2
A collection of objects providing information of the port identification operator profile which is global applied.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdFormatPrfGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.3
A collection of objects providing information of the port identifiction format profile.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdCircuitIdSyntaxGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.4
A collection of objects providing information of the circuit ID syntax item of each format profile.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdOperatorPrfGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.5
A collection of objects providing information of the port identifiction operator profile.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdVlanOperPrfConfGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.6
A collection of objects providing the operator profile information of the VLAN.
Status: current	Access: read-create
OBJECT-GROUP

zxAnPortIdIfOperPrfConfGroup		1.3.6.1.4.1.3902.1082.70.67.4.2.7
A collection of objects providing the operator profile information of the interface.
Status: current	Access: read-create
OBJECT-GROUP