ALTEON-TS-LAYER4-MIB

File: ALTEON-TS-LAYER4-MIB.mib (262636 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
SNMPv2-SMI ALTEON-ROOT-MIB ALTEON-TIGON-SWITCH-MIB

Imported symbols

IpAddress Counter Gauge
OBJECT-TYPE PhysAddress DisplayString
Counter64 switch stats
information operCmds

Defined Types

SlbCurCfgRealServerEntry  
SEQUENCE    
  slbCurCfgRealServerIndex INTEGER
  slbCurCfgRealServerIpAddr IpAddress
  slbCurCfgRealServerWeight INTEGER
  slbCurCfgRealServerMaxConns INTEGER
  slbCurCfgRealServerTimeOut INTEGER
  slbCurCfgRealServerBackUp INTEGER
  slbCurCfgRealServerPingInterval INTEGER
  slbCurCfgRealServerFailRetry INTEGER
  slbCurCfgRealServerSuccRetry INTEGER
  slbCurCfgRealServerState INTEGER
  slbCurCfgRealServerType INTEGER
  slbCurCfgRealServerName DisplayString
  slbCurCfgRealServerUrlBmap OCTET STRING
  slbCurCfgRealServerCookie INTEGER
  slbCurCfgRealServerExcludeStr INTEGER
  slbCurCfgRealServerSubmac INTEGER
  slbCurCfgRealServerProxy INTEGER

SlbNewCfgRealServerEntry  
SEQUENCE    
  slbNewCfgRealServerIndex INTEGER
  slbNewCfgRealServerIpAddr IpAddress
  slbNewCfgRealServerWeight INTEGER
  slbNewCfgRealServerMaxConns INTEGER
  slbNewCfgRealServerTimeOut INTEGER
  slbNewCfgRealServerBackUp INTEGER
  slbNewCfgRealServerPingInterval INTEGER
  slbNewCfgRealServerFailRetry INTEGER
  slbNewCfgRealServerSuccRetry INTEGER
  slbNewCfgRealServerState INTEGER
  slbNewCfgRealServerDelete INTEGER
  slbNewCfgRealServerType INTEGER
  slbNewCfgRealServerName DisplayString
  slbNewCfgRealServerUrlBmap OCTET STRING
  slbNewCfgRealServerAddUrl INTEGER
  slbNewCfgRealServerRemUrl INTEGER
  slbNewCfgRealServerCookie INTEGER
  slbNewCfgRealServerExcludeStr INTEGER
  slbNewCfgRealServerSubmac INTEGER
  slbNewCfgRealServerProxy INTEGER

SlbCurCfgRealServPortEntry  
SEQUENCE    
  slbCurCfgRealServIndex INTEGER
  slbCurCfgRealServPortIndex INTEGER
  slbCurCfgRealServRealPort INTEGER

SlbNewCfgRealServPortEntry  
SEQUENCE    
  slbNewCfgRealServIndex INTEGER
  slbNewCfgRealServPortIndex INTEGER
  slbNewCfgRealServRealPort INTEGER
  slbNewCfgRealServPortDelete INTEGER

SlbCurCfgVirtualServerEntry  
SEQUENCE    
  slbCurCfgVirtServerIndex INTEGER
  slbCurCfgVirtServerIpAddress IpAddress
  slbCurCfgVirtServerLayer3Only INTEGER
  slbCurCfgVirtServerState INTEGER
  slbCurCfgVirtServerDname DisplayString
  slbCurCfgVirtServerCname DisplayString
  slbCurCfgVirtServerCoffset INTEGER
  slbCurCfgVirtServerClength INTEGER
  slbCurCfgVirtServerUriCookie INTEGER
  slbCurCfgVirtServerFtpParsing INTEGER
  slbCurCfgVirtServerUrlHashLen INTEGER
  slbCurCfgVirtServerHttpHdrName DisplayString
  slbCurCfgVirtServerBwmContract INTEGER
  slbCurCfgVirtServerResponseCount INTEGER
  slbCurCfgVirtServerCExpire DisplayString

SlbNewCfgVirtualServerEntry  
SEQUENCE    
  slbNewCfgVirtServerIndex INTEGER
  slbNewCfgVirtServerIpAddress IpAddress
  slbNewCfgVirtServerLayer3Only INTEGER
  slbNewCfgVirtServerState INTEGER
  slbNewCfgVirtServerDelete INTEGER
  slbNewCfgVirtServerDname DisplayString
  slbNewCfgVirtServerCname DisplayString
  slbNewCfgVirtServerCoffset INTEGER
  slbNewCfgVirtServerClength INTEGER
  slbNewCfgVirtServerUriCookie INTEGER
  slbNewCfgVirtServerFtpParsing INTEGER
  slbNewCfgVirtServerUrlHashLen INTEGER
  slbNewCfgVirtServerHttpHdrName DisplayString
  slbNewCfgVirtServerBwmContract INTEGER
  slbNewCfgVirtServerResponseCount INTEGER
  slbNewCfgVirtServerCExpire DisplayString

SlbCurCfgVirtServicesEntry  
SEQUENCE    
  slbCurCfgVirtServIndex INTEGER
  slbCurCfgVirtServiceIndex INTEGER
  slbCurCfgVirtServiceVirtPort INTEGER
  slbCurCfgVirtServiceRealGroup INTEGER
  slbCurCfgVirtServiceRealPort INTEGER
  slbCurCfgVirtServiceUDPBalance INTEGER
  slbCurCfgVirtServiceCookieMode INTEGER
  slbCurCfgVirtServicePBind INTEGER
  slbCurCfgVirtServiceHname DisplayString
  slbCurCfgVirtServiceHttpSlb INTEGER
  slbCurCfgVirtServiceHttpSlbOption INTEGER
  slbCurCfgVirtServiceHttpSlb2 INTEGER
  slbCurCfgVirtServiceBwmContract INTEGER
  slbCurCfgVirtServiceDirServerRtn INTEGER
  slbCurCfgVirtServiceRtspUrlParse INTEGER
  slbCurCfgVirtServiceDBind INTEGER
  slbCurCfgVirtServiceFtpParsing INTEGER
  slbCurCfgVirtServiceRemapUDPFrags INTEGER
  slbCurCfgVirtServiceDnsSlb INTEGER

SlbNewCfgVirtServicesEntry  
SEQUENCE    
  slbNewCfgVirtServIndex INTEGER
  slbNewCfgVirtServiceIndex INTEGER
  slbNewCfgVirtServiceVirtPort INTEGER
  slbNewCfgVirtServiceRealGroup INTEGER
  slbNewCfgVirtServiceRealPort INTEGER
  slbNewCfgVirtServiceUDPBalance INTEGER
  slbNewCfgVirtServicePBind INTEGER
  slbNewCfgVirtServiceCookieMode INTEGER
  slbNewCfgVirtServiceHname DisplayString
  slbNewCfgVirtServiceHttpSlb INTEGER
  slbNewCfgVirtServiceHttpSlbOption INTEGER
  slbNewCfgVirtServiceHttpSlb2 INTEGER
  slbNewCfgVirtServiceBwmContract INTEGER
  slbNewCfgVirtServiceDirServerRtn INTEGER
  slbNewCfgVirtServiceDelete INTEGER
  slbNewCfgVirtServiceRtspUrlParse INTEGER
  slbNewCfgVirtServiceDBind INTEGER
  slbNewCfgVirtServiceFtpParsing INTEGER
  slbNewCfgVirtServiceRemapUDPFrags INTEGER
  slbNewCfgVirtServiceDnsSlb INTEGER

SlbCurCfgUrlBwmEntry  
SEQUENCE    
  slbCurCfgUrlBwmVirtServIndex INTEGER
  slbCurCfgUrlBwmVirtServiceIndex INTEGER
  slbCurCfgUrlBwmUrlId INTEGER
  slbCurCfgUrlBwmContract INTEGER

SlbNewCfgUrlBwmEntry  
SEQUENCE    
  slbNewCfgUrlBwmVirtServIndex INTEGER
  slbNewCfgUrlBwmVirtServiceIndex INTEGER
  slbNewCfgUrlBwmUrlId INTEGER
  slbNewCfgUrlBwmContract INTEGER
  slbNewCfgUrlBwmDelete INTEGER

SlbCurCfgGroupEntry  
SEQUENCE    
  slbCurCfgGroupIndex INTEGER
  slbCurCfgGroupRealServers OCTET STRING
  slbCurCfgGroupMetric INTEGER
  slbCurCfgGroupBackupServer INTEGER
  slbCurCfgGroupHealthCheckUrl DisplayString
  slbCurCfgGroupHealthCheckLayer INTEGER
  slbCurCfgGroupName DisplayString
  slbCurCfgGroupRealThreshold INTEGER
  slbCurCfgGroupBackupGroup INTEGER
  slbCurCfgGroupVipHealthCheck INTEGER

SlbNewCfgGroupEntry  
SEQUENCE    
  slbNewCfgGroupIndex INTEGER
  slbNewCfgGroupRealServers OCTET STRING
  slbNewCfgGroupAddServer INTEGER
  slbNewCfgGroupRemoveServer INTEGER
  slbNewCfgGroupMetric INTEGER
  slbNewCfgGroupBackupServer INTEGER
  slbNewCfgGroupDelete INTEGER
  slbNewCfgGroupHealthCheckUrl DisplayString
  slbNewCfgGroupHealthCheckLayer INTEGER
  slbNewCfgGroupName DisplayString
  slbNewCfgGroupRealThreshold INTEGER
  slbNewCfgGroupBackupGroup INTEGER
  slbNewCfgGroupVipHealthCheck INTEGER

SlbCurCfgPortEntry  
SEQUENCE    
  slbCurCfgPortIndex INTEGER
  slbCurCfgPortProxyIpAddr IpAddress
  slbCurCfgPortSlbState INTEGER
  slbCurCfgPortSlbHotStandby INTEGER
  slbCurCfgPortSlbInterSwitch INTEGER
  slbCurCfgPortSlbPipState INTEGER
  slbCurCfgPortSlbRtsState INTEGER
  slbCurCfgPortSlbIdslbState INTEGER
  slbCurCfgPortSlbNasaState INTEGER

SlbNewCfgPortEntry  
SEQUENCE    
  slbNewCfgPortIndex INTEGER
  slbNewCfgPortProxyIpAddr IpAddress
  slbNewCfgPortSlbState INTEGER
  slbNewCfgPortSlbHotStandby INTEGER
  slbNewCfgPortSlbInterSwitch INTEGER
  slbNewCfgPortSlbPipState INTEGER
  slbNewCfgPortSlbRtsState INTEGER
  slbNewCfgPortDelete INTEGER
  slbNewCfgPortSlbIdslbState INTEGER
  slbNewCfgPortSlbNasaState INTEGER

SlbCurCfgPeerEntry  
SEQUENCE    
  slbCurCfgPeerIndex INTEGER
  slbCurCfgPeerIpAddr IpAddress
  slbCurCfgPeerState INTEGER

SlbNewCfgPeerEntry  
SEQUENCE    
  slbNewCfgPeerIndex INTEGER
  slbNewCfgPeerIpAddr IpAddress
  slbNewCfgPeerState INTEGER
  slbNewCfgPeerDelete INTEGER

SlbCurCfgFailOverTblEntry  
SEQUENCE    
  slbCurCfgFailOverIndex INTEGER
  slbCurCfgFailOverPrimaryIp IpAddress
  slbCurCfgFailOverSecondaryIp IpAddress
  slbCurCfgFailOverSilenceInterval INTEGER
  slbCurCfgFailOverState INTEGER
  slbCurCfgFailOverRouteSupply INTEGER

SlbNewCfgFailOverTblEntry  
SEQUENCE    
  slbNewCfgFailOverIndex INTEGER
  slbNewCfgFailOverPrimaryIp IpAddress
  slbNewCfgFailOverSecondaryIp IpAddress
  slbNewCfgFailOverSilenceInterval INTEGER
  slbNewCfgFailOverState INTEGER
  slbNewCfgFailOverRouteSupply INTEGER

SlbCurCfgUrlExpTableEntry  
SEQUENCE    
  slbCurCfgUrlExpIndex INTEGER
  slbCurCfgUrlExpression DisplayString

SlbNewCfgUrlExpTableEntry  
SEQUENCE    
  slbNewCfgUrlExpIndex INTEGER
  slbNewCfgUrlExpression DisplayString
  slbNewCfgUrlExpDelete INTEGER

SlbCurCfgUrlLbPathTableEntry  
SEQUENCE    
  slbCurCfgUrlLbPathIndex INTEGER
  slbCurCfgUrlLbPathString DisplayString
  slbCurCfgUrlLbBwmContract INTEGER

SlbNewCfgUrlLbPathTableEntry  
SEQUENCE    
  slbNewCfgUrlLbPathIndex INTEGER
  slbNewCfgUrlLbPathString DisplayString
  slbNewCfgUrlLbBwmContract INTEGER
  slbNewCfgUrlLbPathDelete INTEGER

RtspCurCfgUrlExpTableEntry  
SEQUENCE    
  rtspCurCfgUrlExpIndex INTEGER
  rtspCurCfgUrlExpression DisplayString

RtspNewCfgUrlExpTableEntry  
SEQUENCE    
  rtspNewCfgUrlExpIndex INTEGER
  rtspNewCfgUrlExpression DisplayString
  rtspNewCfgUrlExpDelete INTEGER

SlbCurCfgRurlDportTableEntry  
SEQUENCE    
  slbCurCfgRurlDportIndex INTEGER
  slbCurCfgRurlDportLowPort INTEGER
  slbCurCfgRurlDportHighPort INTEGER

SlbNewCfgRurlDportTableEntry  
SEQUENCE    
  slbNewCfgRurlDportIndex INTEGER
  slbNewCfgRurlDportLowPort INTEGER
  slbNewCfgRurlDportHighPort INTEGER
  slbNewCfgRurlDportDelete INTEGER

FltCurCfgTableEntry  
SEQUENCE    
  fltCurCfgIndx INTEGER
  fltCurCfgSrcIpMac INTEGER
  fltCurCfgSrcIp IpAddress
  fltCurCfgSrcIpMask IpAddress
  fltCurCfgDstIpMac INTEGER
  fltCurCfgDstIp IpAddress
  fltCurCfgDstIpMask IpAddress
  fltCurCfgProtocol INTEGER
  fltCurCfgRangeLowSrcPort INTEGER
  fltCurCfgRangeHighSrcPort INTEGER
  fltCurCfgRangeLowDstPort INTEGER
  fltCurCfgRangeHighDstPort INTEGER
  fltCurCfgAction INTEGER
  fltCurCfgRedirPort INTEGER
  fltCurCfgRedirGroup INTEGER
  fltCurCfgLog INTEGER
  fltCurCfgState INTEGER
  fltCurCfgNat INTEGER
  fltCurCfgCache INTEGER
  fltCurCfgInvert INTEGER
  fltCurCfgClientProxy INTEGER
  fltCurCfgTcpAck INTEGER
  fltCurCfgUrlRedir INTEGER
  fltCurCfgSrcMac PhysAddress
  fltCurCfgDstMac PhysAddress
  fltCurCfgFtpNatActive INTEGER
  fltCurCfgAclTcpUrg INTEGER
  fltCurCfgAclTcpAck INTEGER
  fltCurCfgAclTcpPsh INTEGER
  fltCurCfgAclTcpRst INTEGER
  fltCurCfgAclTcpSyn INTEGER
  fltCurCfgAclTcpFin INTEGER
  fltCurCfgAclIcmp INTEGER
  fltCurCfgAclIpOption INTEGER
  fltCurCfgBwmContract INTEGER
  fltCurCfgAclIpTos INTEGER
  fltCurCfgAclIpTosMask INTEGER
  fltCurCfgAclIpTosNew INTEGER
  fltCurCfgFwlb INTEGER
  fltCurCfgNatTimeout INTEGER
  fltCurCfgRurl INTEGER
  fltCurCfgLinklb INTEGER
  fltCurCfgWapRadiusSnoop INTEGER
  fltCurCfgIdslbHash INTEGER
  fltCurCfgVlan INTEGER
  fltCurCfgName DisplayString
  fltCurCfgTcpRateLimit INTEGER
  fltCurCfgTcpRateMaxConn INTEGER
  fltCurCfgHash INTEGER
  fltCurCfgNasa INTEGER
  fltCurCfgLayer7DenyState INTEGER
  fltCurCfgLayer7DenyUrlBmap OCTET STRING

FltNewCfgTableEntry  
SEQUENCE    
  fltNewCfgIndx INTEGER
  fltNewCfgSrcIpMac INTEGER
  fltNewCfgSrcIp IpAddress
  fltNewCfgSrcIpMask IpAddress
  fltNewCfgDstIpMac INTEGER
  fltNewCfgDstIp IpAddress
  fltNewCfgDstIpMask IpAddress
  fltNewCfgProtocol INTEGER
  fltNewCfgRangeLowSrcPort INTEGER
  fltNewCfgRangeHighSrcPort INTEGER
  fltNewCfgRangeLowDstPort INTEGER
  fltNewCfgRangeHighDstPort INTEGER
  fltNewCfgAction INTEGER
  fltNewCfgRedirPort INTEGER
  fltNewCfgRedirGroup INTEGER
  fltNewCfgLog INTEGER
  fltNewCfgState INTEGER
  fltNewCfgDelete INTEGER
  fltNewCfgNat INTEGER
  fltNewCfgCache INTEGER
  fltNewCfgInvert INTEGER
  fltNewCfgClientProxy INTEGER
  fltNewCfgTcpAck INTEGER
  fltNewCfgUrlRedir INTEGER
  fltNewCfgSrcMac PhysAddress
  fltNewCfgDstMac PhysAddress
  fltNewCfgFtpNatActive INTEGER
  fltNewCfgAclTcpUrg INTEGER
  fltNewCfgAclTcpAck INTEGER
  fltNewCfgAclTcpPsh INTEGER
  fltNewCfgAclTcpRst INTEGER
  fltNewCfgAclTcpSyn INTEGER
  fltNewCfgAclTcpFin INTEGER
  fltNewCfgAclIcmp INTEGER
  fltNewCfgAclIpOption INTEGER
  fltNewCfgBwmContract INTEGER
  fltNewCfgAclIpTos INTEGER
  fltNewCfgAclIpTosMask INTEGER
  fltNewCfgAclIpTosNew INTEGER
  fltNewCfgFwlb INTEGER
  fltNewCfgNatTimeout INTEGER
  fltNewCfgRurl INTEGER
  fltNewCfgLinklb INTEGER
  fltNewCfgWapRadiusSnoop INTEGER
  fltNewCfgIdslbHash INTEGER
  fltNewCfgVlan INTEGER
  fltNewCfgName DisplayString
  fltNewCfgTcpRateLimit INTEGER
  fltNewCfgTcpRateMaxConn INTEGER
  fltNewCfgHash INTEGER
  fltNewCfgNasa INTEGER
  fltNewCfgLayer7DenyState INTEGER
  fltNewCfgLayer7DenyUrlBmap OCTET STRING
  fltNewCfgLayer7DenyAddUrl INTEGER
  fltNewCfgLayer7DenyRemUrl INTEGER

FltCurCfgPortTableEntry  
SEQUENCE    
  fltCurCfgPortIndx INTEGER
  fltCurCfgPortState INTEGER
  fltCurCfgPortFiltBmap OCTET STRING

FltNewCfgPortTableEntry  
SEQUENCE    
  fltNewCfgPortIndx INTEGER
  fltNewCfgPortState INTEGER
  fltNewCfgPortFiltBmap OCTET STRING
  fltNewCfgPortAddFiltRule INTEGER
  fltNewCfgPortRemFiltRule INTEGER

FltCurCfgUrlBwmEntry  
SEQUENCE    
  fltCurCfgUrlBwmFltIndex INTEGER
  fltCurCfgUrlBwmUrlId INTEGER
  fltCurCfgUrlBwmContract INTEGER

FltNewCfgUrlBwmEntry  
SEQUENCE    
  fltNewCfgUrlBwmFltIndex INTEGER
  fltNewCfgUrlBwmUrlId INTEGER
  fltNewCfgUrlBwmContract INTEGER
  fltNewCfgUrlBwmDelete INTEGER

GslbCurCfgNetworkTableEntry  
SEQUENCE    
  gslbCurCfgNetworkIndx INTEGER
  gslbCurCfgNetworkSourceIp IpAddress
  gslbCurCfgNetworkNetMask IpAddress
  gslbCurCfgNetworkVip1 IpAddress
  gslbCurCfgNetworkVip2 IpAddress

GslbNewCfgNetworkTableEntry  
SEQUENCE    
  gslbNewCfgNetworkIndx INTEGER
  gslbNewCfgNetworkSourceIp IpAddress
  gslbNewCfgNetworkNetMask IpAddress
  gslbNewCfgNetworkVip1 IpAddress
  gslbNewCfgNetworkVip2 IpAddress
  gslbNewCfgNetworkDelete INTEGER

GslbCurCfgRemSiteTableEntry  
SEQUENCE    
  gslbCurCfgRemSiteIndx INTEGER
  gslbCurCfgRemSitePrimaryIp IpAddress
  gslbCurCfgRemSiteSecondaryIp IpAddress
  gslbCurCfgRemSiteState INTEGER
  gslbCurCfgRemSiteUpdate INTEGER
  gslbCurCfgRemSiteName DisplayString

GslbNewCfgRemSiteTableEntry  
SEQUENCE    
  gslbNewCfgRemSiteIndx INTEGER
  gslbNewCfgRemSitePrimaryIp IpAddress
  gslbNewCfgRemSiteSecondaryIp IpAddress
  gslbNewCfgRemSiteState INTEGER
  gslbNewCfgRemSiteUpdate INTEGER
  gslbNewCfgRemSiteDelete INTEGER
  gslbNewCfgRemSiteName DisplayString

DynSLBRealServerEntry  
SEQUENCE    
  dynSLBRealServerIpAddr IpAddress
  dynSLBRealServerPortNum INTEGER
  dynSLBRealServerWeight INTEGER

SlbStatRServerEntry  
SEQUENCE    
  slbStatRServerIndex INTEGER
  slbStatRServerCurrSessions Gauge
  slbStatRServerTotalSessions Counter
  slbStatRServerFailures Counter
  slbStatRServerHighestSessions Counter
  slbStatRServerHCOctets Counter64
  slbStatRServerHCOctetsLow32 Counter
  slbStatRServerHCOctetsHigh32 Counter

SlbStatGroupEntry  
SEQUENCE    
  slbStatGroupIndex INTEGER
  slbStatGroupCurrSessions Gauge
  slbStatGroupTotalSessions Counter
  slbStatGroupHighestSessions Counter
  slbStatGroupHCOctets Counter64
  slbStatGroupHCOctetsLow32 Counter
  slbStatGroupHCOctetsHigh32 Counter

SlbStatVServerEntry  
SEQUENCE    
  slbStatVServerIndex INTEGER
  slbStatVServerCurrSessions Gauge
  slbStatVServerTotalSessions Counter
  slbStatVServerHighestSessions Counter
  slbStatVServerHCOctets Counter64
  slbStatVServerHCOctetsLow32 Counter
  slbStatVServerHCOctetsHigh32 Counter
  slbStatVServerHeaderHits Counter
  slbStatVServerHeaderMisses Counter
  slbStatVServerHeaderTotalSessions Counter
  slbStatVServerCookieRewrites Counter
  slbStatVServerCookieInserts Counter

SlbStatPortMaintEntry  
SEQUENCE    
  slbStatPortMaintPortIndex INTEGER
  slbStatPortMaintCurBindings Gauge
  slbStatPortMaintBindingFails Counter
  slbStatPortMaintNonTcpFrames Counter
  slbStatPortMaintTcpFragments Counter
  slbStatPortMaintUdpDatagrams Counter
  slbStatPortMaintIncorrectVIPs Counter
  slbStatPortMaintIncorrectVports Counter
  slbStatPortMaintRealServerNoAvails Counter
  slbStatPortMaintFilteredDeniedFrames Counter
  slbStatPortMaintCurBindings4Seconds Gauge
  slbStatPortMaintCurBindings64Seconds Gauge
  slbStatPortMaintVMAdiscards Counter

SlbStatPortRealServerEntry  
SEQUENCE    
  slbStatPortRealServerPortIndex INTEGER
  slbStatPortRealServerServerIndex INTEGER
  slbStatPortRealServerCurrSessions Gauge
  slbStatPortRealServerTotalSessions Counter
  slbStatPortRealServerHCOctets Counter64
  slbStatPortRealServerHCOctetsLow32 Counter
  slbStatPortRealServerHCOctetsHigh32 Counter

FltStatTableEntry  
SEQUENCE    
  fltStatFltIndex INTEGER
  fltStatFltFirings Counter

GslbStatRemRealServerEntry  
SEQUENCE    
  gslbStatRemRealServerIndex INTEGER
  gslbStatRemRealServerDnsHandoffs Counter
  gslbStatRemRealServerHttpRedirs Counter

UrlStatSlbPathTableEntry  
SEQUENCE    
  urlStatSlbPathIndex INTEGER
  urlStatSlbPathHits Counter

NasaStatSpEntry  
SEQUENCE    
  nasaStatSpPortIndex INTEGER
  nasaStatSpCtlTunnelIn Counter
  nasaStatSpCtlTunnelInvalidPkt Counter
  nasaStatSpReqSessCnt Counter
  nasaStatSpSessAddCnt Counter
  nasaStatSpSessDelCnt Counter
  nasaStatSpSessUpdCnt Counter
  nasaStatSpSessRdCnt Counter
  nasaStatSpSessCharCnt Counter
  nasaStatSpReqSessNoIsd Counter
  nasaStatSpCtlTunnelToMp Counter
  nasaStatSpBcastTunnelCnt Counter
  nasaStatSpBcastTunnelToMp Counter
  nasaStatSpBcastTunnelToIsd Counter
  nasaStatSpRurlTunnelCnt Counter
  nasaStatSpIpDatagramCnt Counter
  nasaStatSpCliRedirectCnt Counter
  nasaStatSpInvalidVersion Counter
  nasaStatSpAckTx Counter
  nasaStatSpAckRx Counter
  nasaStatSpAckAlloc Counter
  nasaStatSpAckFree Counter
  nasaStatSpAllocAckFail Counter
  nasaStatSpAllocFrmFail Counter
  nasaStatSpRexmitFail Counter
  nasaStatSpInvalidIsd Counter
  nasaStatSpInvalidPkts Counter

SlbFailOverInfoEntry  
SEQUENCE    
  slbFailOverInfoIndex INTEGER
  slbFailOverInfoPrimaryIp IpAddress
  slbFailOverInfoPrimaryStatus INTEGER
  slbFailOverInfoPrimaryState INTEGER
  slbFailOverInfoSecondaryIp IpAddress
  slbFailOverInfoSecondaryStatus INTEGER
  slbFailOverInfoSecondaryState INTEGER

SlbRealServerInfoEntry  
SEQUENCE    
  slbRealServerInfoIndex INTEGER
  slbRealServerInfoIpAddr IpAddress
  slbRealServerMacAddr PhysAddress
  slbRealServerInfoSwitchPort INTEGER
  slbRealServerInfoHealthLayer INTEGER
  slbRealServerInfoOverflow INTEGER
  slbRealServerInfoState INTEGER

NasaIsdInfoEntry  
SEQUENCE    
  nasaIsdInfoIndex INTEGER
  nasaIsdInfoIpAddr IpAddress
  nasaIsdMacAddr PhysAddress
  nasaIsdInfoSwitchPort INTEGER
  nasaIsdInfoGdi INTEGER
  nasaIsdInfoState INTEGER
  nasaIsdInfoStateChange INTEGER

OperSlbPortEntry  
SEQUENCE    
  operSlbPortIndex INTEGER
  operSlbPortClrSessionTab INTEGER

SlbOperRealServerEntry  
SEQUENCE    
  slbOperRealServerIndex INTEGER
  slbOperRealServerStatus INTEGER

Defined Values

serverloadbalance 1.3.6.1.4.1.1872.2.1.5
OBJECT IDENTIFIER    

filtering 1.3.6.1.4.1.1872.2.1.10
OBJECT IDENTIFIER    

globalSLB 1.3.6.1.4.1.1872.2.1.11
OBJECT IDENTIFIER    

dynamicSLB 1.3.6.1.4.1.1872.2.1.12
OBJECT IDENTIFIER    

slbfailover 1.3.6.1.4.1.1872.2.1.5.16
OBJECT IDENTIFIER    

slbUrl 1.3.6.1.4.1.1872.2.1.5.27
OBJECT IDENTIFIER    

slbUrlRedir 1.3.6.1.4.1.1872.2.1.5.27.1
OBJECT IDENTIFIER    

slbUrlBalance 1.3.6.1.4.1.1872.2.1.5.27.2
OBJECT IDENTIFIER    

rtspUrlRedir 1.3.6.1.4.1.1872.2.1.5.27.3
OBJECT IDENTIFIER    

slbRurl 1.3.6.1.4.1.1872.2.1.5.52
OBJECT IDENTIFIER    

slbRurlGeneral 1.3.6.1.4.1.1872.2.1.5.52.1
OBJECT IDENTIFIER    

slbWaphc 1.3.6.1.4.1.1872.2.1.5.62
OBJECT IDENTIFIER    

slbWap 1.3.6.1.4.1.1872.2.1.5.63
OBJECT IDENTIFIER    

synAttackDetCfg 1.3.6.1.4.1.1872.2.1.5.82
OBJECT IDENTIFIER    

gslbGeneral 1.3.6.1.4.1.1872.2.1.11.1
OBJECT IDENTIFIER    

gslbDNS 1.3.6.1.4.1.1872.2.1.11.2
OBJECT IDENTIFIER    

gslbSites 1.3.6.1.4.1.1872.2.1.11.3
OBJECT IDENTIFIER    

gslbLookup 1.3.6.1.4.1.1872.2.1.11.4
OBJECT IDENTIFIER    

slbStats 1.3.6.1.4.1.1872.2.1.8.2
OBJECT IDENTIFIER    

filterStats 1.3.6.1.4.1.1872.2.1.8.6
OBJECT IDENTIFIER    

gslbStats 1.3.6.1.4.1.1872.2.1.8.7
OBJECT IDENTIFIER    

gslbMaintStats 1.3.6.1.4.1.1872.2.1.8.8
OBJECT IDENTIFIER    

urlStats 1.3.6.1.4.1.1872.2.1.8.10
OBJECT IDENTIFIER    

tcpStats 1.3.6.1.4.1.1872.2.1.8.11
OBJECT IDENTIFIER    

ftpStats 1.3.6.1.4.1.1872.2.1.8.14
OBJECT IDENTIFIER    

rurlStats 1.3.6.1.4.1.1872.2.1.8.18
OBJECT IDENTIFIER    

rtspStats 1.3.6.1.4.1.1872.2.1.8.19
OBJECT IDENTIFIER    

tcpLimitStats 1.3.6.1.4.1.1872.2.1.8.23
OBJECT IDENTIFIER    

nasaStats 1.3.6.1.4.1.1872.2.1.8.24
OBJECT IDENTIFIER    

dnsSlbStats 1.3.6.1.4.1.1872.2.1.8.25
OBJECT IDENTIFIER    

slb-info 1.3.6.1.4.1.1872.2.1.9.2
OBJECT IDENTIFIER    

slbOper 1.3.6.1.4.1.1872.2.1.14.4
OBJECT IDENTIFIER    

slbRealServerMaxSize 1.3.6.1.4.1.1872.2.1.5.1
The maximum number of entries in SLB RealServerTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServerTable 1.3.6.1.4.1.1872.2.1.5.2
The table of Real Server configuration in the current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgRealServerEntry

slbCurCfgRealServerEntry 1.3.6.1.4.1.1872.2.1.5.2.1
Information about a particular Real Server configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgRealServerEntry  

slbCurCfgRealServerIndex 1.3.6.1.4.1.1872.2.1.5.2.1.1
The real server number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServerIpAddr 1.3.6.1.4.1.1872.2.1.5.2.1.2
IP address of the real server identified by the instance of the slbRealServerIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgRealServerWeight 1.3.6.1.4.1.1872.2.1.5.2.1.3
The server weight.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..48  

slbCurCfgRealServerMaxConns 1.3.6.1.4.1.1872.2.1.5.2.1.4
The maximum number of connections that are allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..200000  

slbCurCfgRealServerTimeOut 1.3.6.1.4.1.1872.2.1.5.2.1.5
The maximum number of minutes an inactive connection remains open.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..30  

slbCurCfgRealServerBackUp 1.3.6.1.4.1.1872.2.1.5.2.1.6
The backup server number for this server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServerPingInterval 1.3.6.1.4.1.1872.2.1.5.2.1.7
The interval between keep-alive (ping) attempts in number of seconds. Zero means disabling ping attempt.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..60  

slbCurCfgRealServerFailRetry 1.3.6.1.4.1.1872.2.1.5.2.1.8
The number of failed attempts to declare this server DOWN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

slbCurCfgRealServerSuccRetry 1.3.6.1.4.1.1872.2.1.5.2.1.9
The number of successful attempts to declare a server UP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

slbCurCfgRealServerState 1.3.6.1.4.1.1872.2.1.5.2.1.10
Enable or disable this server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbCurCfgRealServerType 1.3.6.1.4.1.1872.2.1.5.2.1.11
The server type. It participates in global server load balancing when it is configured as remote-server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local-server(1), remote-server(2)  

slbCurCfgRealServerName 1.3.6.1.4.1.1872.2.1.5.2.1.12
The name of the real server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbCurCfgRealServerUrlBmap 1.3.6.1.4.1.1872.2.1.5.2.1.13
The URL Pathes selected for URL load balancing for by the real server. The selected URL Pathes are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ URL Path 9 || || || ||___ URL Path 8 || |____ URL Path 7 || . . . ||_________ URL Path 2 |__________ URL Path 1 where x : 1 - The represented URL Path is selected 0 - The represented URL Path is not selected
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

slbCurCfgRealServerCookie 1.3.6.1.4.1.1872.2.1.5.2.1.14
The real server that will handle client requests that doesn't contain an URL cookie if Cookie loadbalance is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgRealServerExcludeStr 1.3.6.1.4.1.1872.2.1.5.2.1.15
The real server will handle requests that don't match the loadbalance string if it is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgRealServerSubmac 1.3.6.1.4.1.1872.2.1.5.2.1.16
The real server config to enable/disable MAC SA substitution for L4 traffic. If disabled (the default) we will NOT substitute the MAC SA of client-to-server frames. If enabled, we will substitute the MAC SA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgRealServerProxy 1.3.6.1.4.1.1872.2.1.5.2.1.17
The real server config to enable/disable client proxy operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgRealServerTable 1.3.6.1.4.1.1872.2.1.5.3
The table of Real Server configuration in the new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgRealServerEntry

slbNewCfgRealServerEntry 1.3.6.1.4.1.1872.2.1.5.3.1
Information about a particular Real Server configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgRealServerEntry  

slbNewCfgRealServerIndex 1.3.6.1.4.1.1872.2.1.5.3.1.1
The real server number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServerIpAddr 1.3.6.1.4.1.1872.2.1.5.3.1.2
IP address of the real server identified by the instance of slbRealServerIndex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgRealServerWeight 1.3.6.1.4.1.1872.2.1.5.3.1.3
The server weight.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..48  

slbNewCfgRealServerMaxConns 1.3.6.1.4.1.1872.2.1.5.3.1.4
The maximum number of connections that are allowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..200000  

slbNewCfgRealServerTimeOut 1.3.6.1.4.1.1872.2.1.5.3.1.5
The maximum number of minutes an inactive connection remains open.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..30  

slbNewCfgRealServerBackUp 1.3.6.1.4.1.1872.2.1.5.3.1.6
The backup server number for this server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServerPingInterval 1.3.6.1.4.1.1872.2.1.5.3.1.7
The interval between keep-alive (ping) attempts in number of seconds. Zero means disabling ping attempt.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..60  

slbNewCfgRealServerFailRetry 1.3.6.1.4.1.1872.2.1.5.3.1.8
The number of failed attempts to declare this server DOWN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..63  

slbNewCfgRealServerSuccRetry 1.3.6.1.4.1.1872.2.1.5.3.1.9
The number of successful attempts to declare a server UP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..63  

slbNewCfgRealServerState 1.3.6.1.4.1.1872.2.1.5.3.1.10
Enable or disable this server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbNewCfgRealServerDelete 1.3.6.1.4.1.1872.2.1.5.3.1.11
By setting the value to delete(2), the entire row is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbNewCfgRealServerType 1.3.6.1.4.1.1872.2.1.5.3.1.12
The server type. It participates in global server load balancing when it is configured as remote-server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local-server(1), remote-server(2)  

slbNewCfgRealServerName 1.3.6.1.4.1.1872.2.1.5.3.1.13
The name of the real server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbNewCfgRealServerUrlBmap 1.3.6.1.4.1.1872.2.1.5.3.1.14
The URL Pathes selected for URL load balancing for by the real server. The selected URL Pathes are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ URL Path 9 || || || ||___ URL Path 8 || |____ URL Path 7 || . . . ||_________ URL Path 2 |__________ URL Path 1 where x : 1 - The represented URL Path is selected 0 - The represented URL Path is not selected
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

slbNewCfgRealServerAddUrl 1.3.6.1.4.1.1872.2.1.5.3.1.15
The URL Path (slbCurCfgUrlLbPathIndex) to be added to the real server. A zero is returned when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServerRemUrl 1.3.6.1.4.1.1872.2.1.5.3.1.16
The URL Path (slbCurCfgUrlLbPathIndex) to be removed from the real server. A zero is returned when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServerCookie 1.3.6.1.4.1.1872.2.1.5.3.1.17
Enable or disable real server to handle client requests that don't contain a cookie if cookie loadbalance is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgRealServerExcludeStr 1.3.6.1.4.1.1872.2.1.5.3.1.18
Enable or disable exclusionary matching string on real server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgRealServerSubmac 1.3.6.1.4.1.1872.2.1.5.3.1.19
The real server config to enable/disable MAC SA substitution for L4 traffic. If disabled (the default) we will NOT substitute the MAC SA of client-to-server frames. If enabled, we will substitute the MAC SA.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgRealServerProxy 1.3.6.1.4.1.1872.2.1.5.3.1.20
The real server config to enable/disable client proxy operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbRealServPortTableMaxSize 1.3.6.1.4.1.1872.2.1.5.53
The maximum number of entries in SLB RealServPortTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServPortTable 1.3.6.1.4.1.1872.2.1.5.48
The table of real server service ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgRealServPortEntry

slbCurCfgRealServPortEntry 1.3.6.1.4.1.1872.2.1.5.48.1
A row in the real server service ports table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgRealServPortEntry  

slbCurCfgRealServIndex 1.3.6.1.4.1.1872.2.1.5.48.1.1
The number of the real server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServPortIndex 1.3.6.1.4.1.1872.2.1.5.48.1.2
The port index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRealServRealPort 1.3.6.1.4.1.1872.2.1.5.48.1.3
The layer4 real service port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..65534  

slbNewCfgRealServPortTable 1.3.6.1.4.1.1872.2.1.5.49
The table of real server service ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgRealServPortEntry

slbNewCfgRealServPortEntry 1.3.6.1.4.1.1872.2.1.5.49.1
A row in the real server service ports table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgRealServPortEntry  

slbNewCfgRealServIndex 1.3.6.1.4.1.1872.2.1.5.49.1.1
The number of the real server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServPortIndex 1.3.6.1.4.1.1872.2.1.5.49.1.2
The port index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgRealServRealPort 1.3.6.1.4.1.1872.2.1.5.49.1.3
The layer4 real service port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..65534  

slbNewCfgRealServPortDelete 1.3.6.1.4.1.1872.2.1.5.49.1.4
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbVirtServerTableMaxSize 1.3.6.1.4.1.1872.2.1.5.4
The maximum number of entries in SLB VirtServerTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServerTable 1.3.6.1.4.1.1872.2.1.5.5
The table of virtual Servers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgVirtualServerEntry

slbCurCfgVirtualServerEntry 1.3.6.1.4.1.1872.2.1.5.5.1
A row in the virtual server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgVirtualServerEntry  

slbCurCfgVirtServerIndex 1.3.6.1.4.1.1872.2.1.5.5.1.1
Virtual Server Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServerIpAddress 1.3.6.1.4.1.1872.2.1.5.5.1.2
IP address of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgVirtServerLayer3Only 1.3.6.1.4.1.1872.2.1.5.5.1.3
Enable or disable layer3 only balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER layer3Only(1), disabled(2)  

slbCurCfgVirtServerState 1.3.6.1.4.1.1872.2.1.5.5.1.4
Enable or disable the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbCurCfgVirtServerDname 1.3.6.1.4.1.1872.2.1.5.5.1.5
The domain name of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..34)  

slbCurCfgVirtServerCname 1.3.6.1.4.1.1872.2.1.5.5.1.6
The cookie name of the virtual server used for cookie load balance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbCurCfgVirtServerCoffset 1.3.6.1.4.1.1872.2.1.5.5.1.7
The starting byte offset of the cookie value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..64  

slbCurCfgVirtServerClength 1.3.6.1.4.1.1872.2.1.5.5.1.8
The number of bytes to extract from the cookie value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..64  

slbCurCfgVirtServerUriCookie 1.3.6.1.4.1.1872.2.1.5.5.1.9
Enable or disable cookie search in URI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServerFtpParsing 1.3.6.1.4.1.1872.2.1.5.5.1.10
Enable or Disable the ftp parsing for the virtual server.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServerUrlHashLen 1.3.6.1.4.1.1872.2.1.5.5.1.11
The number of bytes used to hash onto server. A zero means URL hashing disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

slbCurCfgVirtServerHttpHdrName 1.3.6.1.4.1.1872.2.1.5.5.1.12
The HTTP header name of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbCurCfgVirtServerBwmContract 1.3.6.1.4.1.1872.2.1.5.5.1.13
The default BW contract of virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServerResponseCount 1.3.6.1.4.1.1872.2.1.5.5.1.14
The number of cookie search response count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

slbCurCfgVirtServerCExpire 1.3.6.1.4.1.1872.2.1.5.5.1.15
The cookie expire of the virtual server used for insert cookie load balance depending on the mode it has the following format absolute mode or for relative mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbNewCfgVirtServerTable 1.3.6.1.4.1.1872.2.1.5.6
The table of virtual Servers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgVirtualServerEntry

slbNewCfgVirtualServerEntry 1.3.6.1.4.1.1872.2.1.5.6.1
A row in the virtual server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgVirtualServerEntry  

slbNewCfgVirtServerIndex 1.3.6.1.4.1.1872.2.1.5.6.1.1
The Virtual Server Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServerIpAddress 1.3.6.1.4.1.1872.2.1.5.6.1.2
IP address of the virtual server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgVirtServerLayer3Only 1.3.6.1.4.1.1872.2.1.5.6.1.3
Enable or disable layer3 only balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER layer3Only(1), disabled(2)  

slbNewCfgVirtServerState 1.3.6.1.4.1.1872.2.1.5.6.1.4
Enable or disable the virtual server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbNewCfgVirtServerDelete 1.3.6.1.4.1.1872.2.1.5.6.1.5
By setting the value to delete(2), the entire row is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbNewCfgVirtServerDname 1.3.6.1.4.1.1872.2.1.5.6.1.6
The domain name of the virtual server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..34)  

slbNewCfgVirtServerCname 1.3.6.1.4.1.1872.2.1.5.6.1.7
The cookie name of the virtual server used for cookie load balance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbNewCfgVirtServerCoffset 1.3.6.1.4.1.1872.2.1.5.6.1.8
The starting byte offset of the cookie value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..64  

slbNewCfgVirtServerClength 1.3.6.1.4.1.1872.2.1.5.6.1.9
The number of bytes to extract from the cookie value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..64  

slbNewCfgVirtServerUriCookie 1.3.6.1.4.1.1872.2.1.5.6.1.10
Enable or disable cookie search in URI
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServerFtpParsing 1.3.6.1.4.1.1872.2.1.5.6.1.11
Enable or Disable the ftp parsing for the virtual server.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServerUrlHashLen 1.3.6.1.4.1.1872.2.1.5.6.1.12
The number of bytes used to hash onto server, A zero means URL hashing disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

slbNewCfgVirtServerHttpHdrName 1.3.6.1.4.1.1872.2.1.5.6.1.13
The HTTP header name of the virtual server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbNewCfgVirtServerBwmContract 1.3.6.1.4.1.1872.2.1.5.6.1.14
The default BW contract number of the virtual server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServerResponseCount 1.3.6.1.4.1.1872.2.1.5.6.1.15
The number of cookie search response count.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

slbNewCfgVirtServerCExpire 1.3.6.1.4.1.1872.2.1.5.6.1.16
The cookie expire of the virtual server used for insert cookie load balance depending on the mode it has the following format absolute mode or for relative mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbVirtServicesTableMaxSize 1.3.6.1.4.1.1872.2.1.5.55
The maximum number of entries in SLB Virtual Services Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServicesTable 1.3.6.1.4.1.1872.2.1.5.7
The table of virtual services.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgVirtServicesEntry

slbCurCfgVirtServicesEntry 1.3.6.1.4.1.1872.2.1.5.7.1
A row in the virtual services table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgVirtServicesEntry  

slbCurCfgVirtServIndex 1.3.6.1.4.1.1872.2.1.5.7.1.1
The number of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServiceIndex 1.3.6.1.4.1.1872.2.1.5.7.1.2
The service index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServiceVirtPort 1.3.6.1.4.1.1872.2.1.5.7.1.3
The layer4 virtual port number of the service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..65534  

slbCurCfgVirtServiceRealGroup 1.3.6.1.4.1.1872.2.1.5.7.1.4
The real server group number for this service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServiceRealPort 1.3.6.1.4.1.1872.2.1.5.7.1.5
The layer4 real port number of the service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

slbCurCfgVirtServiceUDPBalance 1.3.6.1.4.1.1872.2.1.5.7.1.6
Enable, disable or stateless the UDP balancing for the virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3), stateless(4)  

slbCurCfgVirtServicePBind 1.3.6.1.4.1.1872.2.1.5.7.1.7
Enable or disable persistent bindings for the virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3), sessid(4), cookie(5)  

slbCurCfgVirtServiceHname 1.3.6.1.4.1.1872.2.1.5.7.1.8
The host name of the virtual service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..9)  

slbCurCfgVirtServiceHttpSlb 1.3.6.1.4.1.1872.2.1.5.7.1.9
Select HTTP server loadbalancing for the virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), urlslb(2), urlhash(3), cookie(4), host(5), browser(6), others(7), headerhash(8)  

slbCurCfgVirtServiceHttpSlbOption 1.3.6.1.4.1.1872.2.1.5.7.1.16
Select HTTP server loadbalancing option for the virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER and(1), or(2), none(3)  

slbCurCfgVirtServiceHttpSlb2 1.3.6.1.4.1.1872.2.1.5.7.1.17
Select HTTP server loadbalancing for the virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), urlslb(2), urlhash(3), cookie(4), host(5), browser(6), others(7), headerhash(8)  

slbCurCfgVirtServiceBwmContract 1.3.6.1.4.1.1872.2.1.5.7.1.10
The BWM contract number for this service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgVirtServiceDirServerRtn 1.3.6.1.4.1.1872.2.1.5.7.1.11
Enable or disable direct server return feature. To translate only MAC addresses in performing server load balancing when enabled. This allow servers to return directly to client since IP addresses have not been changed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServiceRtspUrlParse 1.3.6.1.4.1.1872.2.1.5.7.1.12
Enable or disable RTSP URL hashing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(2), hash(3), patternMatch(4)  

slbCurCfgVirtServiceDBind 1.3.6.1.4.1.1872.2.1.5.7.1.14
Enable or disable Delayed Binding.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServiceCookieMode 1.3.6.1.4.1.1872.2.1.5.7.1.13
Select cookie persistance mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rewrite(1), passive(2), insert(3), disabled(4)  

slbCurCfgVirtServiceFtpParsing 1.3.6.1.4.1.1872.2.1.5.7.1.15
Enable or Disable the ftp parsing for the virtual service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServiceRemapUDPFrags 1.3.6.1.4.1.1872.2.1.5.7.1.18
Enable or disable remapping UDP server fragments
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtServiceDnsSlb 1.3.6.1.4.1.1872.2.1.5.7.1.19
Enable or disable DNS query load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServicesTable 1.3.6.1.4.1.1872.2.1.5.8
The table of virtual Services.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgVirtServicesEntry

slbNewCfgVirtServicesEntry 1.3.6.1.4.1.1872.2.1.5.8.1
A row in the virtual services table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgVirtServicesEntry  

slbNewCfgVirtServIndex 1.3.6.1.4.1.1872.2.1.5.8.1.1
The number of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServiceIndex 1.3.6.1.4.1.1872.2.1.5.8.1.2
The service index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServiceVirtPort 1.3.6.1.4.1.1872.2.1.5.8.1.3
The layer4 virtual port number of the service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..65534  

slbNewCfgVirtServiceRealGroup 1.3.6.1.4.1.1872.2.1.5.8.1.4
The real server group number for this service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServiceRealPort 1.3.6.1.4.1.1872.2.1.5.8.1.5
The layer4 real port number of the service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgVirtServiceUDPBalance 1.3.6.1.4.1.1872.2.1.5.8.1.6
Enable, disable or stateless the UDP balancing for the virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3), stateless(4)  

slbNewCfgVirtServicePBind 1.3.6.1.4.1.1872.2.1.5.8.1.7
Enable or disable persistent bindings for the virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3), sessid(4), cookie(5)  

slbNewCfgVirtServiceHname 1.3.6.1.4.1.1872.2.1.5.8.1.8
The host name of the virtual service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..9)  

slbNewCfgVirtServiceHttpSlb 1.3.6.1.4.1.1872.2.1.5.8.1.9
Select HTTP server loadbalancing for the virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), urlslb(2), urlhash(3), cookie(4), host(5), browser(6), others(7), headerhash(8)  

slbNewCfgVirtServiceHttpSlbOption 1.3.6.1.4.1.1872.2.1.5.8.1.17
Select HTTP server loadbalancing for the virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER and(1), or(2), none(3)  

slbNewCfgVirtServiceHttpSlb2 1.3.6.1.4.1.1872.2.1.5.8.1.18
Select HTTP server loadbalancing for the virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), urlslb(2), urlhash(3), cookie(4), host(5), browser(6), others(7), headerhash(8)  

slbNewCfgVirtServiceBwmContract 1.3.6.1.4.1.1872.2.1.5.8.1.10
The BWM contract number for this service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgVirtServiceDirServerRtn 1.3.6.1.4.1.1872.2.1.5.8.1.11
Enable or disable direct server return feature. To translate only MAC addresses in performing server load balancing when enabled. This allow servers to return directly to client since IP addresses have not been changed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServiceDelete 1.3.6.1.4.1.1872.2.1.5.8.1.12
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbNewCfgVirtServiceRtspUrlParse 1.3.6.1.4.1.1872.2.1.5.8.1.13
Enable or disable RTSP URL hashing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(2), hash(3), patternMatch(4)  

slbNewCfgVirtServiceDBind 1.3.6.1.4.1.1872.2.1.5.8.1.15
Enable or disable Delayed Binding.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServiceCookieMode 1.3.6.1.4.1.1872.2.1.5.8.1.14
Select cookie persistance mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rewrite(1), passive(2), insert(3), disabled(4)  

slbNewCfgVirtServiceFtpParsing 1.3.6.1.4.1.1872.2.1.5.8.1.16
Enable or Disable the ftp parsing for the virtual service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServiceRemapUDPFrags 1.3.6.1.4.1.1872.2.1.5.8.1.19
Enable or disable remapping UDP server fragments
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtServiceDnsSlb 1.3.6.1.4.1.1872.2.1.5.8.1.20
Enable or disable DNS query load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbUrlBwmTableMaxSize 1.3.6.1.4.1.1872.2.1.5.56
The maximum number of entries in SLB URL BWM Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlBwmTable 1.3.6.1.4.1.1872.2.1.5.50
The table of URL based BWM for Virtual Services.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgUrlBwmEntry

slbCurCfgUrlBwmEntry 1.3.6.1.4.1.1872.2.1.5.50.1
A row in the URL based BWM virtual services table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgUrlBwmEntry  

slbCurCfgUrlBwmVirtServIndex 1.3.6.1.4.1.1872.2.1.5.50.1.1
The number of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlBwmVirtServiceIndex 1.3.6.1.4.1.1872.2.1.5.50.1.2
The service index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlBwmUrlId 1.3.6.1.4.1.1872.2.1.5.50.1.3
The URL Path Identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlBwmContract 1.3.6.1.4.1.1872.2.1.5.50.1.4
The BW contract number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlBwmTable 1.3.6.1.4.1.1872.2.1.5.51
The table of URL based BWM for Virtual Services.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgUrlBwmEntry

slbNewCfgUrlBwmEntry 1.3.6.1.4.1.1872.2.1.5.51.1
A row in the URL based BWM virtual services table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgUrlBwmEntry  

slbNewCfgUrlBwmVirtServIndex 1.3.6.1.4.1.1872.2.1.5.51.1.1
The number of the virtual server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlBwmVirtServiceIndex 1.3.6.1.4.1.1872.2.1.5.51.1.2
The service index. This has no external meaning
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlBwmUrlId 1.3.6.1.4.1.1872.2.1.5.51.1.3
The URL Path Identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlBwmContract 1.3.6.1.4.1.1872.2.1.5.51.1.4
The BW contract number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlBwmDelete 1.3.6.1.4.1.1872.2.1.5.51.1.5
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbGroupTableMaxSize 1.3.6.1.4.1.1872.2.1.5.9
The maximum number of entries in slbCurCfgGroupTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgGroupTable 1.3.6.1.4.1.1872.2.1.5.10
The table of groups
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgGroupEntry

slbCurCfgGroupEntry 1.3.6.1.4.1.1872.2.1.5.10.1
A row in the slbCurCfgGroupTable
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgGroupEntry  

slbCurCfgGroupIndex 1.3.6.1.4.1.1872.2.1.5.10.1.1
The group number for which the information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgGroupRealServers 1.3.6.1.4.1.1872.2.1.5.10.1.2
The Real servers in the group. The servers are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... | || |_ server 9 | || | ||___ server 8 | |____ server 7 | . . . |__________ server 1 where x : 1 - The represented server belongs to the group 0 - The represented server does not belong to the group
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

slbCurCfgGroupMetric 1.3.6.1.4.1.1872.2.1.5.10.1.3
The metric used to select next server in group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER roundRobin(1), leastConnections(2), minMisses(3), hash(4), response(5), bandwidth(6)  

slbCurCfgGroupBackupServer 1.3.6.1.4.1.1872.2.1.5.10.1.4
The backup real server for this group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgGroupHealthCheckUrl 1.3.6.1.4.1.1872.2.1.5.10.1.5
The specific content which is examined during health checks. The content depends on the type of health check.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbCurCfgGroupHealthCheckLayer 1.3.6.1.4.1.1872.2.1.5.10.1.6
The OSI layer at which servers are health checked.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER icmp(1), tcp(2), http(3), dns(4), smtp(5), pop3(6), nntp(7), ftp(8), imap(9), radius(10), sslh(11), script1(12), script2(13), script3(14), script4(15), script5(16), script6(17), script7(18), script8(19), script9(20), script10(21), script11(22), script12(23), script13(24), script14(25), script15(26), script16(27), link(28), wsp(29), wtls(30), ldap(31), udpdns(32), arp(33)  

slbCurCfgGroupName 1.3.6.1.4.1.1872.2.1.5.10.1.7
The name of the real server group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbCurCfgGroupRealThreshold 1.3.6.1.4.1.1872.2.1.5.10.1.8
The server failure syslog threshold of the real server group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

slbCurCfgGroupBackupGroup 1.3.6.1.4.1.1872.2.1.5.10.1.9
The backup real server group for this group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgGroupVipHealthCheck 1.3.6.1.4.1.1872.2.1.5.10.1.10
Enable or disable VIP health checking in DSR mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgGroupTable 1.3.6.1.4.1.1872.2.1.5.11
The table of groups
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgGroupEntry

slbNewCfgGroupEntry 1.3.6.1.4.1.1872.2.1.5.11.1
A row in the slbNewCfgGroupTable
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgGroupEntry  

slbNewCfgGroupIndex 1.3.6.1.4.1.1872.2.1.5.11.1.1
The group number for which the information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgGroupRealServers 1.3.6.1.4.1.1872.2.1.5.11.1.2
The Real servers in the group. The servers are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... | || |_ server 9 | || | ||___ server 8 | |____ server 7 | . . . |__________ server 1 where x : 1 - The represented server belongs to the group 0 - The represented server does not belong to the group
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

slbNewCfgGroupAddServer 1.3.6.1.4.1.1872.2.1.5.11.1.3
The real server to be added to the group. When read, 0 is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgGroupRemoveServer 1.3.6.1.4.1.1872.2.1.5.11.1.4
The real server to be removed from the group. When read, 0 is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgGroupMetric 1.3.6.1.4.1.1872.2.1.5.11.1.5
The metric used to select next server in group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER roundRobin(1), leastConnections(2), minMisses(3), hash(4), response(5), bandwidth(6)  

slbNewCfgGroupBackupServer 1.3.6.1.4.1.1872.2.1.5.11.1.6
The backup real server for this group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgGroupDelete 1.3.6.1.4.1.1872.2.1.5.11.1.7
By setting the value to delete(2), the entire group is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbNewCfgGroupHealthCheckUrl 1.3.6.1.4.1.1872.2.1.5.11.1.8
The specific content which is examined during health checks. The content depends on the type of health check.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbNewCfgGroupHealthCheckLayer 1.3.6.1.4.1.1872.2.1.5.11.1.9
The OSI layer at which servers are health checked.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER icmp(1), tcp(2), http(3), dns(4), smtp(5), pop3(6), nntp(7), ftp(8), imap(9), radius(10), sslh(11), script1(12), script2(13), script3(14), script4(15), script5(16), script6(17), script7(18), script8(19), script9(20), script10(21), script11(22), script12(23), script13(24), script14(25), script15(26), script16(27), link(28), wsp(29), wtls(30), ldap(31), udpdns(32), arp(33)  

slbNewCfgGroupName 1.3.6.1.4.1.1872.2.1.5.11.1.10
The name of the real server group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

slbNewCfgGroupRealThreshold 1.3.6.1.4.1.1872.2.1.5.11.1.11
The server failure syslog threshold of the real server group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

slbNewCfgGroupBackupGroup 1.3.6.1.4.1.1872.2.1.5.11.1.12
The backup real server group for this group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgGroupVipHealthCheck 1.3.6.1.4.1.1872.2.1.5.11.1.13
Enable or disable VIP health checking in DSR mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbPortTableMaxSize 1.3.6.1.4.1.1872.2.1.5.54
The maximum number of entries in SLB Port Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgPortTable 1.3.6.1.4.1.1872.2.1.5.12
The table of ports and their SLB states
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgPortEntry

slbCurCfgPortEntry 1.3.6.1.4.1.1872.2.1.5.12.1
A row in the slbPortTable
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgPortEntry  

slbCurCfgPortIndex 1.3.6.1.4.1.1872.2.1.5.12.1.1
The port number for which the SLB information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgPortProxyIpAddr 1.3.6.1.4.1.1872.2.1.5.12.1.2
The proxy IP address of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgPortSlbState 1.3.6.1.4.1.1872.2.1.5.12.1.3
The SLB state of the port. none(1) - not SLB port client(2) - SLB client port server(3) - SLB server port client-server(4) - SLB client and server port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), client(2), server(3), client-server(4)  

slbCurCfgPortSlbHotStandby 1.3.6.1.4.1.1872.2.1.5.12.1.4
Enable or disable hot standby processing on the switch port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPortSlbInterSwitch 1.3.6.1.4.1.1872.2.1.5.12.1.5
Enable or disable inter-switch processing on the switch port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPortSlbPipState 1.3.6.1.4.1.1872.2.1.5.12.1.6
Enable or disable use of proxy IP address on the switch port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPortSlbRtsState 1.3.6.1.4.1.1872.2.1.5.12.1.7
Enable or disable RTS processing on the switch port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPortSlbIdslbState 1.3.6.1.4.1.1872.2.1.5.12.1.8
Enable or disable Intrusion Detection server load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPortSlbNasaState 1.3.6.1.4.1.1872.2.1.5.12.1.9
Enable or disable NASA base processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortTable 1.3.6.1.4.1.1872.2.1.5.13
The table of ports and their SLB states
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgPortEntry

slbNewCfgPortEntry 1.3.6.1.4.1.1872.2.1.5.13.1
A row in the slbPortTable
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgPortEntry  

slbNewCfgPortIndex 1.3.6.1.4.1.1872.2.1.5.13.1.1
The port number for which the SLB information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgPortProxyIpAddr 1.3.6.1.4.1.1872.2.1.5.13.1.2
The proxy IP address of the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgPortSlbState 1.3.6.1.4.1.1872.2.1.5.13.1.3
The SLB state of the port. none(1) - not SLB port client(2) - SLB client port server(3) - SLB server port client-server(4) - SLB client and server port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), client(2), server(3), client-server(4)  

slbNewCfgPortSlbHotStandby 1.3.6.1.4.1.1872.2.1.5.13.1.4
Enable or disable hot standby processing on the switch port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortSlbInterSwitch 1.3.6.1.4.1.1872.2.1.5.13.1.5
Enable or disable inter-switch processing on the switch port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortSlbPipState 1.3.6.1.4.1.1872.2.1.5.13.1.6
Enable or disable use of proxy IP address on the switch port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortSlbRtsState 1.3.6.1.4.1.1872.2.1.5.13.1.7
Enable or disable RTS processing on the switch port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortDelete 1.3.6.1.4.1.1872.2.1.5.13.1.8
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbNewCfgPortSlbIdslbState 1.3.6.1.4.1.1872.2.1.5.13.1.9
Enable or disable Intrusion Detection server load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgPortSlbNasaState 1.3.6.1.4.1.1872.2.1.5.13.1.10
Enable or disable NASA base processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgImask 1.3.6.1.4.1.1872.2.1.5.14
The virtual and real IP address mask - corresponding to the imask command of the slb configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbNewCfgImask 1.3.6.1.4.1.1872.2.1.5.15
The virtual and real IP address mask - corresponding to the imask command of the slb configuration menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbCurCfgMnet 1.3.6.1.4.1.1872.2.1.5.19
The management network - corresponding to the mnet command of the slb configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbNewCfgMnet 1.3.6.1.4.1.1872.2.1.5.20
The management network - corresponding to the mnet command of the slb configuration menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbCurCfgMmask 1.3.6.1.4.1.1872.2.1.5.21
The management subnet mask - corresponding to the mmask command of the slb configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbNewCfgMmask 1.3.6.1.4.1.1872.2.1.5.22
The management subnet mask - corresponding to the mmask command of the slb configuration menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbCurCfgRadiusAuthenString 1.3.6.1.4.1.1872.2.1.5.23
The RADIUS authentication string. The string is used for generating encrypted authentication string for RADIUS health check.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbNewCfgRadiusAuthenString 1.3.6.1.4.1.1872.2.1.5.24
The RADIUS authentication string. The string is used for generating encrypted authentication string for RADIUS health check.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbCurCfgDirectMode 1.3.6.1.4.1.1872.2.1.5.25
Enable or disable direct access mode. It allows direct access to real servers and any combination of virtual and real servers when set to enabled(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgDirectMode 1.3.6.1.4.1.1872.2.1.5.26
Enable or disable direct access mode. It allows direct access to real servers and any combination of virtual and real servers when set to enabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgPmask 1.3.6.1.4.1.1872.2.1.5.28
The persistent mask - corresponding to the pmask command of the slb configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbNewCfgPmask 1.3.6.1.4.1.1872.2.1.5.29
The persistent mask - corresponding to the pmask command of the slb configuration menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbCurCfgGrace 1.3.6.1.4.1.1872.2.1.5.30
Enable or disable graceful server failure. It allows to keep the connection to the failure real servers when set to enabled(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgGrace 1.3.6.1.4.1.1872.2.1.5.31
Enable or disable graceful server failure. It allows to keep the connection to the failure real servers when set to enabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgWapTpcp 1.3.6.1.4.1.1872.2.1.5.63.1
Enable or disable WAP load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgWapTpcp 1.3.6.1.4.1.1872.2.1.5.63.2
Enable or disable WAP load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgWapDebug 1.3.6.1.4.1.1872.2.1.5.63.3
WAP Debug level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..10  

slbNewCfgWapDebug 1.3.6.1.4.1.1872.2.1.5.63.4
WAP Debug level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

slbPeerTableMaxSize 1.3.6.1.4.1.1872.2.1.5.57
The maximum number of entries in SLB Peer Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgPeerTable 1.3.6.1.4.1.1872.2.1.5.32
The table of Synch Peer Switch configuration in the current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgPeerEntry

slbCurCfgPeerEntry 1.3.6.1.4.1.1872.2.1.5.32.1
Information about Synch Peer Switch configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgPeerEntry  

slbCurCfgPeerIndex 1.3.6.1.4.1.1872.2.1.5.32.1.1
The index for synch peer switchs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgPeerIpAddr 1.3.6.1.4.1.1872.2.1.5.32.1.2
The IP address of the peer switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgPeerState 1.3.6.1.4.1.1872.2.1.5.32.1.3
Enable or disable the peer switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

slbNewCfgPeerTable 1.3.6.1.4.1.1872.2.1.5.33
The table of Synch Peer Switch configuration in the new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgPeerEntry

slbNewCfgPeerEntry 1.3.6.1.4.1.1872.2.1.5.33.1
Information about synch peer switch configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgPeerEntry  

slbNewCfgPeerIndex 1.3.6.1.4.1.1872.2.1.5.33.1.1
The index number for synch peer switchs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgPeerIpAddr 1.3.6.1.4.1.1872.2.1.5.33.1.2
The IP address of the peer switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgPeerState 1.3.6.1.4.1.1872.2.1.5.33.1.3
Enable or disable the peer switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

slbNewCfgPeerDelete 1.3.6.1.4.1.1872.2.1.5.33.1.4
By setting the value to delete(2), the entire row is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbCurCfgSyncFilt 1.3.6.1.4.1.1872.2.1.5.34
Enable or disable synch filter configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncFilt 1.3.6.1.4.1.1872.2.1.5.35
Enable or disable synch filter configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgSyncPort 1.3.6.1.4.1.1872.2.1.5.36
Enable or disable synch port configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncPort 1.3.6.1.4.1.1872.2.1.5.37
Enable or disable synch port configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgSyncVrrp 1.3.6.1.4.1.1872.2.1.5.38
Enable or disable synch VRRP Priorities.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncVrrp 1.3.6.1.4.1.1872.2.1.5.39
Enable or disable synch VRRP Priorities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgSyncPip 1.3.6.1.4.1.1872.2.1.5.40
Enable or disable synch proxy IP addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncPip 1.3.6.1.4.1.1872.2.1.5.41
Enable or disable synch proxy IP addresses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgSyncSfo 1.3.6.1.4.1.1872.2.1.5.44
Enable or disable synch stateful failover.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncSfo 1.3.6.1.4.1.1872.2.1.5.45
Enable or disable synch stateful failover.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgSyncSfoUpdatePeriod 1.3.6.1.4.1.1872.2.1.5.46
The stateful failover update period in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..60  

slbNewCfgSyncSfoUpdatePeriod 1.3.6.1.4.1.1872.2.1.5.47
The stateful failover update period in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

slbCurCfgSyncBwm 1.3.6.1.4.1.1872.2.1.5.64
Enable or disable syncing BWM configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgSyncBwm 1.3.6.1.4.1.1872.2.1.5.65
Enable or disable syncing BWM configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgVirtMatrixArch 1.3.6.1.4.1.1872.2.1.5.42
Enable or disable Virtual Matrix Architecture.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgVirtMatrixArch 1.3.6.1.4.1.1872.2.1.5.43
Enable or disable Virtual Matrix Architecture.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgFastage 1.3.6.1.4.1.1872.2.1.5.58
Session table fast-age (1 sec) period bit shift.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

slbNewCfgFastage 1.3.6.1.4.1.1872.2.1.5.59
Session table fast-age (1 sec) period bit shift.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

slbCurCfgSlowage 1.3.6.1.4.1.1872.2.1.5.60
Session table slow-age (2 min) period bit shift.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

slbNewCfgSlowage 1.3.6.1.4.1.1872.2.1.5.61
Session table slow-age (2 min) period bit shift.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

slbCurCfgTpcp 1.3.6.1.4.1.1872.2.1.5.66
Enable or disable Transparent Proxy Cache Protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgTpcp 1.3.6.1.4.1.1872.2.1.5.67
Enable or disable Transparent Proxy Cache Protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgMetricInterval 1.3.6.1.4.1.1872.2.1.5.68
The interval of response and bandwidth metric updates.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

slbNewCfgMetricInterval 1.3.6.1.4.1.1872.2.1.5.69
The interval of response and bandwidth metric updates.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..256  

slbCurCfgRealGroupIdslb 1.3.6.1.4.1.1872.2.1.5.70
The real server group number for IDSLB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

slbNewCfgRealGroupIdslb 1.3.6.1.4.1.1872.2.1.5.71
The real server group number for IDSLB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..256  

slbCurCfgLdapVersion 1.3.6.1.4.1.1872.2.1.5.72
The version number for LDAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER version2(1), version3(2)  

slbNewCfgLdapVersion 1.3.6.1.4.1.1872.2.1.5.73
The Version number of LDAP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER version2(1), version3(2)  

slbCurCfgIsdInterval 1.3.6.1.4.1.1872.2.1.5.74
The interval of ISD health checks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..60  

slbNewCfgIsdInterval 1.3.6.1.4.1.1872.2.1.5.75
The interval of ISD health checks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

slbCurCfgIsdRetry 1.3.6.1.4.1.1872.2.1.5.76
The number of failed attemps to declare ISD down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

slbNewCfgIsdRetry 1.3.6.1.4.1.1872.2.1.5.77
The number of failed attemps to declare ISD down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..63  

slbCurCfgIsdRestr 1.3.6.1.4.1.1872.2.1.5.78
The number of successful attemps to declare ISD up.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

slbNewCfgIsdRestr 1.3.6.1.4.1.1872.2.1.5.79
The number of successful attemps to declare ISD up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..63  

slbCurCfgIsdNumber 1.3.6.1.4.1.1872.2.1.5.80
The number of real servers used for ISDs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

slbNewCfgIsdNumber 1.3.6.1.4.1.1872.2.1.5.81
The number of real servers used for ISDs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

slbCurCfgTcpTimeWindow 1.3.6.1.4.1.1872.2.1.5.83
The time window for TCP rate limiting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

slbNewCfgTcpTimeWindow 1.3.6.1.4.1.1872.2.1.5.84
The time window for TCP rate limiting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

slbCurCfgTcpHoldDuration 1.3.6.1.4.1.1872.2.1.5.85
The hold down duration for TCP rate limiting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

slbNewCfgTcpHoldDuration 1.3.6.1.4.1.1872.2.1.5.86
The hold down duration for TCP rate limiting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

slbCurCfgAllowHttpHc 1.3.6.1.4.1.1872.2.1.5.87
Enable or disable allow HTTP health check on any port. If disabled the non-HTTP virtual services will use TCP Health Checks, if enabled the HTTP Content Health Check will be sent to any port except HTTPS (443) if properly configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgAllowHttpHc 1.3.6.1.4.1.1872.2.1.5.88
Enable or disable allow HTTP health check on any port. If disabled the non-HTTP virtual services will use TCP Health Checks, if enabled the HTTP Content Health Check will be sent to any port except HTTPS (443) if properly configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgFailOverTable 1.3.6.1.4.1.1872.2.1.5.16.1
The table of current switch fail-over configuration.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgFailOverTblEntry

slbCurCfgFailOverTblEntry 1.3.6.1.4.1.1872.2.1.5.16.1.1
A row in the current switch fail-over configuration table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgFailOverTblEntry  

slbCurCfgFailOverIndex 1.3.6.1.4.1.1872.2.1.5.16.1.1.1
The index of current switch fail-over configuration table.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgFailOverPrimaryIp 1.3.6.1.4.1.1872.2.1.5.16.1.1.2
The IP address of the Primary switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgFailOverSecondaryIp 1.3.6.1.4.1.1872.2.1.5.16.1.1.3
The IP address of the Secondary switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

slbCurCfgFailOverSilenceInterval 1.3.6.1.4.1.1872.2.1.5.16.1.1.4
Number of seconds before a silent peer is assumed down.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 2..120  

slbCurCfgFailOverState 1.3.6.1.4.1.1872.2.1.5.16.1.1.5
Enable or disable slb switch failover feature.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbCurCfgFailOverRouteSupply 1.3.6.1.4.1.1872.2.1.5.16.1.1.6
Enable or disable to supply network routes update when switch is a standby switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgFailOverTable 1.3.6.1.4.1.1872.2.1.5.16.2
The table of new switch fail-over configuration.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgFailOverTblEntry

slbNewCfgFailOverTblEntry 1.3.6.1.4.1.1872.2.1.5.16.2.1
A row in the new switch fail-over configuration table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgFailOverTblEntry  

slbNewCfgFailOverIndex 1.3.6.1.4.1.1872.2.1.5.16.2.1.1
The index of new switch fail-over configuration table.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgFailOverPrimaryIp 1.3.6.1.4.1.1872.2.1.5.16.2.1.2
The IP address of the Primary switch.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgFailOverSecondaryIp 1.3.6.1.4.1.1872.2.1.5.16.2.1.3
The IP address of the Secondary switch.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

slbNewCfgFailOverSilenceInterval 1.3.6.1.4.1.1872.2.1.5.16.2.1.4
Number of seconds before a silent peer is assumed down.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 2..120  

slbNewCfgFailOverState 1.3.6.1.4.1.1872.2.1.5.16.2.1.5
Enable or disable slb switch failover feature.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbNewCfgFailOverRouteSupply 1.3.6.1.4.1.1872.2.1.5.16.2.1.6
Enable or disable to supply network routes update when switch is a standby switch.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgGlobalControl 1.3.6.1.4.1.1872.2.1.5.17
The global state of Server Load Balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbNewCfgGlobalControl 1.3.6.1.4.1.1872.2.1.5.18
The global state of Server Load Balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

slbCurCfgUrlExpTable 1.3.6.1.4.1.1872.2.1.5.27.1.1
The table of URL expressions in the current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgUrlExpTableEntry

slbCurCfgUrlExpTableEntry 1.3.6.1.4.1.1872.2.1.5.27.1.1.1
Information about a expression for URL parsing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgUrlExpTableEntry  

slbCurCfgUrlExpIndex 1.3.6.1.4.1.1872.2.1.5.27.1.1.1.1
The URL expressions table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlExpression 1.3.6.1.4.1.1872.2.1.5.27.1.1.1.2
The expressions for URL parsing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbNewCfgUrlExpTable 1.3.6.1.4.1.1872.2.1.5.27.1.2
The table of URL expressions in the new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgUrlExpTableEntry

slbNewCfgUrlExpTableEntry 1.3.6.1.4.1.1872.2.1.5.27.1.2.1
Information about a expression for URL parsing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgUrlExpTableEntry  

slbNewCfgUrlExpIndex 1.3.6.1.4.1.1872.2.1.5.27.1.2.1.1
The URL expressions table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlExpression 1.3.6.1.4.1.1872.2.1.5.27.1.2.1.2
The expressions for URL parsing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

slbNewCfgUrlExpDelete 1.3.6.1.4.1.1872.2.1.5.27.1.2.1.3
Action object to delete an URL expression. When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbCurCfgUrlRedirNonGetOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.3
This is for controlling if the switch should redirect packet to the origin server when HTTP non-GETs are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgUrlRedirNonGetOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.4
This is for controlling if the switch should redirect packet to the origin server when HTTP non-GETs are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgUrlRedirCookieOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.5
This is for controlling if the switch should redirect packet to the origin server when user cookies are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgUrlRedirCookieOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.6
This is for controlling if the switch should redirect packet to the origin server when user cookies are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgUrlRedirNoCacheOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.7
This is for controlling if the switch should redirect packet to the origin server when no-cache header are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgUrlRedirNoCacheOrigSrv 1.3.6.1.4.1.1872.2.1.5.27.1.8
This is for controlling if the switch should redirect packet to the origin server when no-cache header are detected. enabled(1) - Allow redirect traffic to the origin server disabled(2)- redirect to a group of servers
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgUrlRedirUriHashLength 1.3.6.1.4.1.1872.2.1.5.27.1.9
Specify the number of bytes in the URI will be used to hash onto server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

slbNewCfgUrlRedirUriHashLength 1.3.6.1.4.1.1872.2.1.5.27.1.10
Specify the number of bytes in the URI will be used to hash onto server
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

slbCurCfgUrlRedirHeader 1.3.6.1.4.1.1872.2.1.5.27.1.11
This is for controlling if the switch should redirect packet to the cache server based on HTTP header. enabled(1) - Redirect web traffic based on HTTP header disabled(2)- Redirect web traffic based on URI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgUrlRedirHeader 1.3.6.1.4.1.1872.2.1.5.27.1.12
This is for controlling if the switch should redirect packet to the cache server based on HTTP header. enabled(1) - Redirect web traffic based on HTTP header disabled(2)- Redirect web traffic based on URI
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbCurCfgUrlRedirHeaderName 1.3.6.1.4.1.1872.2.1.5.27.1.13
The HTTP header name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbNewCfgUrlRedirHeaderName 1.3.6.1.4.1.1872.2.1.5.27.1.14
The HTTP header name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

slbUrlExpTableMaxSize 1.3.6.1.4.1.1872.2.1.5.27.1.15
The maximum number of entries in SLB Url Expression table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlLbPathTable 1.3.6.1.4.1.1872.2.1.5.27.2.1
The table of URL path for URL load balancing in the current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgUrlLbPathTableEntry

slbCurCfgUrlLbPathTableEntry 1.3.6.1.4.1.1872.2.1.5.27.2.1.1
Information about an URL path for URL load balancing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgUrlLbPathTableEntry  

slbCurCfgUrlLbPathIndex 1.3.6.1.4.1.1872.2.1.5.27.2.1.1.1
The URL path table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgUrlLbPathString 1.3.6.1.4.1.1872.2.1.5.27.2.1.1.2
The URL path for URL load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..40)  

slbCurCfgUrlLbBwmContract 1.3.6.1.4.1.1872.2.1.5.27.2.1.1.3
The BW contract for the path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlLbPathTable 1.3.6.1.4.1.1872.2.1.5.27.2.2
The table of URL path for URL load balancing in the new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgUrlLbPathTableEntry

slbNewCfgUrlLbPathTableEntry 1.3.6.1.4.1.1872.2.1.5.27.2.2.1
Information about an URL path for URL load balancing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgUrlLbPathTableEntry  

slbNewCfgUrlLbPathIndex 1.3.6.1.4.1.1872.2.1.5.27.2.2.1.1
The URL path table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlLbPathString 1.3.6.1.4.1.1872.2.1.5.27.2.2.1.2
The URL path for URL load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..40)  

slbNewCfgUrlLbBwmContract 1.3.6.1.4.1.1872.2.1.5.27.2.2.1.4
The BW contract for the load path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgUrlLbPathDelete 1.3.6.1.4.1.1872.2.1.5.27.2.2.1.3
Action object to delete an URL Path. When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbCurCfgUrlLbErrorMsg 1.3.6.1.4.1.1872.2.1.5.27.2.3
Customize error message to send back to client when switch cannot bind client's request to servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

slbNewCfgUrlLbErrorMsg 1.3.6.1.4.1.1872.2.1.5.27.2.4
Customize error message to send back to client when switch cannot bind client's request to servers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

slbUrlLbPathTableMaxSize 1.3.6.1.4.1.1872.2.1.5.27.2.5
The maximum number of entries in SLB URL load balance table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rtspUrlExpTableMaxSize 1.3.6.1.4.1.1872.2.1.5.27.3.1
The maximum number of entries in RTSP URL expression table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rtspCurCfgUrlExpTable 1.3.6.1.4.1.1872.2.1.5.27.3.2
The table of RTSP URL expressions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtspCurCfgUrlExpTableEntry

rtspCurCfgUrlExpTableEntry 1.3.6.1.4.1.1872.2.1.5.27.3.2.1
Information about a expression in the RTSP URL Redirection table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RtspCurCfgUrlExpTableEntry  

rtspCurCfgUrlExpIndex 1.3.6.1.4.1.1872.2.1.5.27.3.2.1.1
The RTSP URL expression table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rtspCurCfgUrlExpression 1.3.6.1.4.1.1872.2.1.5.27.3.2.1.2
The expressions for RTSP URL redirection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

rtspNewCfgUrlExpTable 1.3.6.1.4.1.1872.2.1.5.27.3.3
The table of RTSP URL expressions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RtspNewCfgUrlExpTableEntry

rtspNewCfgUrlExpTableEntry 1.3.6.1.4.1.1872.2.1.5.27.3.3.1
Information about a expression in the RTSP URL Redirection table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RtspNewCfgUrlExpTableEntry  

rtspNewCfgUrlExpIndex 1.3.6.1.4.1.1872.2.1.5.27.3.3.1.1
The RTSP URL expression table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rtspNewCfgUrlExpression 1.3.6.1.4.1.1872.2.1.5.27.3.3.1.2
The expression for RTSP URL redirection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

rtspNewCfgUrlExpDelete 1.3.6.1.4.1.1872.2.1.5.27.3.3.1.3
Action object to delete an RTSP URL expression. When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbCurCfgRurlGenDeny 1.3.6.1.4.1.1872.2.1.5.52.1.1
This is for controlling if the switch should deny packets from passing through to L2 in the event that the switch runs out of buffer resources.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbNewCfgRurlGenDeny 1.3.6.1.4.1.1872.2.1.5.52.1.2
This is for controlling if the switch should deny packets from passing through to L2 in the event that the switch runs out of buffer resources.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

slbRurlDportTableMaxSize 1.3.6.1.4.1.1872.2.1.5.52.2
The maximum number of entries in RURL destination port table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRurlDportTable 1.3.6.1.4.1.1872.2.1.5.52.3
The table of RURL destination port ranges in current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbCurCfgRurlDportTableEntry

slbCurCfgRurlDportTableEntry 1.3.6.1.4.1.1872.2.1.5.52.3.1
Information about a destination port range for RURL parsing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbCurCfgRurlDportTableEntry  

slbCurCfgRurlDportIndex 1.3.6.1.4.1.1872.2.1.5.52.3.1.1
The RURL destination port table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

slbCurCfgRurlDportLowPort 1.3.6.1.4.1.1872.2.1.5.52.3.1.2
The first destination port in the port range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

slbCurCfgRurlDportHighPort 1.3.6.1.4.1.1872.2.1.5.52.3.1.3
The last destination port in the port range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgRurlDportTable 1.3.6.1.4.1.1872.2.1.5.52.4
The table of RURL destination port ranges in new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlbNewCfgRurlDportTableEntry

slbNewCfgRurlDportTableEntry 1.3.6.1.4.1.1872.2.1.5.52.4.1
Information about a destination port range for RURL parsing.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SlbNewCfgRurlDportTableEntry  

slbNewCfgRurlDportIndex 1.3.6.1.4.1.1872.2.1.5.52.4.1.1
The RURL destination port table index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

slbNewCfgRurlDportLowPort 1.3.6.1.4.1.1872.2.1.5.52.4.1.2
The first destination port in the port range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgRurlDportHighPort 1.3.6.1.4.1.1872.2.1.5.52.4.1.3
The last destination port in the port range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgRurlDportDelete 1.3.6.1.4.1.1872.2.1.5.52.4.1.4
Action object to delete an destination port/range. When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

slbCurCfgWaphcWSPPort 1.3.6.1.4.1.1872.2.1.5.62.1
The WSP port number to health check.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgWaphcWSPPort 1.3.6.1.4.1.1872.2.1.5.62.2
The WSP port number to health check.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

slbCurCfgWaphcOffset 1.3.6.1.4.1.1872.2.1.5.62.3
The offset in received WSP packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

slbNewCfgWaphcOffset 1.3.6.1.4.1.1872.2.1.5.62.4
The offset in received WSP packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..256  

slbCurCfgWaphcSndContent 1.3.6.1.4.1.1872.2.1.5.62.5
The content to be sent to the WAP gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

slbNewCfgWaphcSndContent 1.3.6.1.4.1.1872.2.1.5.62.6
The content to be sent to the WAP gateway.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

slbCurCfgWaphcRcvContent 1.3.6.1.4.1.1872.2.1.5.62.7
The content to be received from the WAP gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

slbNewCfgWaphcRcvContent 1.3.6.1.4.1.1872.2.1.5.62.8
The content to be received from the WAP gateway.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

slbCurCfgWaphcWTLSPort 1.3.6.1.4.1.1872.2.1.5.62.9
The WTLS port number to health check.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

slbNewCfgWaphcWTLSPort 1.3.6.1.4.1.1872.2.1.5.62.10
The WTLS port number to health check.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

synAttackCurCfgInterval 1.3.6.1.4.1.1872.2.1.5.82.1
The interval specified in seconds determines how frequently the switch checks for SYN attacks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..3600  

synAttackNewCfgInterval 1.3.6.1.4.1.1872.2.1.5.82.2
The interval specified in seconds determines how frequently the switch checks for SYN attacks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..3600  

synAttackCurCfgThreshhold 1.3.6.1.4.1.1872.2.1.5.82.3
The threshhold indicating the number of new half-open sessions per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100000  

synAttackNewCfgThreshhold 1.3.6.1.4.1.1872.2.1.5.82.4
The threshhold indicating the number of new half-open sessions per second.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100000  

fltCfgTableMaxSize 1.3.6.1.4.1.1872.2.1.10.1
The maximum number of filtering table entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgTable 1.3.6.1.4.1.1872.2.1.10.2
The filtering table in the current configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltCurCfgTableEntry

fltCurCfgTableEntry 1.3.6.1.4.1.1872.2.1.10.2.1
A row in the filtering table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltCurCfgTableEntry  

fltCurCfgIndx 1.3.6.1.4.1.1872.2.1.10.2.1.1
The filteriang table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgSrcIp 1.3.6.1.4.1.1872.2.1.10.2.1.2
The source IP address to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

fltCurCfgSrcIpMask 1.3.6.1.4.1.1872.2.1.10.2.1.3
The source IP sub-net mask for filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

fltCurCfgDstIp 1.3.6.1.4.1.1872.2.1.10.2.1.4
The destination IP address to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

fltCurCfgDstIpMask 1.3.6.1.4.1.1872.2.1.10.2.1.5
The destination IP sub-net mask for filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

fltCurCfgProtocol 1.3.6.1.4.1.1872.2.1.10.2.1.6
The protocol to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgRangeHighSrcPort 1.3.6.1.4.1.1872.2.1.10.2.1.7
The higher source TCP/UDP port number to be filtered. It applies only when protocol defined in fltCurCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

fltCurCfgRangeLowSrcPort 1.3.6.1.4.1.1872.2.1.10.2.1.8
The lower source TCP/UDP port number to be filtered. It applies only when protocol defined in fltCurCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

fltCurCfgRangeLowDstPort 1.3.6.1.4.1.1872.2.1.10.2.1.9
The lower destination TCP/UDP port number to be filtered. It applies only when protocol defined in fltCurCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

fltCurCfgRangeHighDstPort 1.3.6.1.4.1.1872.2.1.10.2.1.10
The higher destination TCP/UDP port number to be filtered. It applies only when protocol defined in fltCurCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

fltCurCfgAction 1.3.6.1.4.1.1872.2.1.10.2.1.11
The action for the filtering rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER allow(1), deny(2), redirect(3), nat(4)  

fltCurCfgRedirPort 1.3.6.1.4.1.1872.2.1.10.2.1.12
The real server port number used for redirection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

fltCurCfgRedirGroup 1.3.6.1.4.1.1872.2.1.10.2.1.13
The real server group to be redirected to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgLog 1.3.6.1.4.1.1872.2.1.10.2.1.14
Enable or disable logging.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgState 1.3.6.1.4.1.1872.2.1.10.2.1.15
The state of this filtering rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgNat 1.3.6.1.4.1.1872.2.1.10.2.1.16
The selection of destination or source for network address translation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER destination-address(1), source-address(2)  

fltCurCfgCache 1.3.6.1.4.1.1872.2.1.10.2.1.17
Enable or disable caching sessions that match filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgInvert 1.3.6.1.4.1.1872.2.1.10.2.1.18
Turn the invert logic on or off for the filter entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invert-on(1), invert-off(2)  

fltCurCfgClientProxy 1.3.6.1.4.1.1872.2.1.10.2.1.19
Enable or disable client proxy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgTcpAck 1.3.6.1.4.1.1872.2.1.10.2.1.20
Enable or disable filtering on matching TCP ACK and RST flag.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgUrlRedir 1.3.6.1.4.1.1872.2.1.10.2.1.21
Enable or disable URL redirection. The URL expressions are defined in slbCurCfgUrlTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgSrcMac 1.3.6.1.4.1.1872.2.1.10.2.1.22
The source MAC address to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

fltCurCfgDstMac 1.3.6.1.4.1.1872.2.1.10.2.1.23
The Destination MAC address to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

fltCurCfgFtpNatActive 1.3.6.1.4.1.1872.2.1.10.2.1.24
Enable or disable FTP NAT for active ftp only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgAclTcpUrg 1.3.6.1.4.1.1872.2.1.10.2.1.25
Enable or disable TCP URG packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclTcpAck 1.3.6.1.4.1.1872.2.1.10.2.1.26
Enable or disable TCP ACK packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclTcpPsh 1.3.6.1.4.1.1872.2.1.10.2.1.27
Enable or disable TCP PSH packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclTcpRst 1.3.6.1.4.1.1872.2.1.10.2.1.28
Enable or disable TCP RST packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclTcpSyn 1.3.6.1.4.1.1872.2.1.10.2.1.29
Enable or disable TCP SYN packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclTcpFin 1.3.6.1.4.1.1872.2.1.10.2.1.30
Enable or disable TCP FIN packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgAclIcmp 1.3.6.1.4.1.1872.2.1.10.2.1.31
ICMP type to be filtered. A ICMP type of 255 indicates 'any'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

fltCurCfgAclIpOption 1.3.6.1.4.1.1872.2.1.10.2.1.32
Enable or disable IP option matching.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltCurCfgBwmContract 1.3.6.1.4.1.1872.2.1.10.2.1.33
Filt default BW contract number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgAclIpTos 1.3.6.1.4.1.1872.2.1.10.2.1.34
The IP TOS value to be filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

fltCurCfgAclIpTosMask 1.3.6.1.4.1.1872.2.1.10.2.1.35
The IP TOS mask for filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

fltCurCfgAclIpTosNew 1.3.6.1.4.1.1872.2.1.10.2.1.36
The new IP TOS value to over-write when filtering fired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

fltCurCfgFwlb 1.3.6.1.4.1.1872.2.1.10.2.1.37
Enable or disable filtering on firewall redirect hash method.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgNatTimeout 1.3.6.1.4.1.1872.2.1.10.2.1.38
The NAT session timeout. The timeout value should be an even number between (4..30)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 4..30  

fltCurCfgRurl 1.3.6.1.4.1.1872.2.1.10.2.1.39
Enable or disable RURL parsing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgLinklb 1.3.6.1.4.1.1872.2.1.10.2.1.40
Enable or disable WAN link load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgWapRadiusSnoop 1.3.6.1.4.1.1872.2.1.10.2.1.41
Enable or disable WAP RADIUS snooping.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgSrcIpMac 1.3.6.1.4.1.1872.2.1.10.2.1.42
Set a flag indicating whether filtering should be based on the source IP address or the source MAC address field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), mac(2)  

fltCurCfgDstIpMac 1.3.6.1.4.1.1872.2.1.10.2.1.43
Set a flag indicating whether filtering should be based on the destination IP address or the destination MAC address field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), mac(2)  

fltCurCfgIdslbHash 1.3.6.1.4.1.1872.2.1.10.2.1.44
Set hash parameter for intrusion detection server load balancing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sip(1), dip(2), both(3)  

fltCurCfgVlan 1.3.6.1.4.1.1872.2.1.10.2.1.45
Set the VLAN assoicated with the filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..4094  

fltCurCfgName 1.3.6.1.4.1.1872.2.1.10.2.1.46
The name of the filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

fltCurCfgTcpRateLimit 1.3.6.1.4.1.1872.2.1.10.2.1.47
Enable or disable TCP connection rate limiting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgTcpRateMaxConn 1.3.6.1.4.1.1872.2.1.10.2.1.48
Set maximum connections (number of connections in units of 10) for TCP connection rate limiting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

fltCurCfgHash 1.3.6.1.4.1.1872.2.1.10.2.1.49
Set hash parameter for the filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), sip(2), dip(3), both(4), sipsport(5)  

fltCurCfgNasa 1.3.6.1.4.1.1872.2.1.10.2.1.50
Enable or disable NASA redirect to ISD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgLayer7DenyState 1.3.6.1.4.1.1872.2.1.10.2.1.51
Enable or disable layer 7 deny filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgLayer7DenyUrlBmap 1.3.6.1.4.1.1872.2.1.10.2.1.52
The URL strings selected for Layer 7 deny filters. The selected URL strings are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ URL Path 9 || || || ||___ URL Path 8 || |____ URL Path 7 || . . . ||_________ URL Path 2 |__________ URL Path 1 where x : 1 - The represented URL string is selected 0 - The represented URL string is not selected
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

fltNewCfgTable 1.3.6.1.4.1.1872.2.1.10.3
The filtering table in the new configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltNewCfgTableEntry

fltNewCfgTableEntry 1.3.6.1.4.1.1872.2.1.10.3.1
A row in the filtering table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltNewCfgTableEntry  

fltNewCfgIndx 1.3.6.1.4.1.1872.2.1.10.3.1.1
The filtering table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltNewCfgSrcIp 1.3.6.1.4.1.1872.2.1.10.3.1.2
The source IP address to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

fltNewCfgSrcIpMask 1.3.6.1.4.1.1872.2.1.10.3.1.3
The source IP sub-net mask for filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

fltNewCfgDstIp 1.3.6.1.4.1.1872.2.1.10.3.1.4
The destination IP address to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

fltNewCfgDstIpMask 1.3.6.1.4.1.1872.2.1.10.3.1.5
The destination IP sub-net mask for filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

fltNewCfgProtocol 1.3.6.1.4.1.1872.2.1.10.3.1.6
The protocol to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgRangeHighSrcPort 1.3.6.1.4.1.1872.2.1.10.3.1.7
The higher source TCP/UDP port number to be filtered. It applies only when protocol defined in fltNewCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

fltNewCfgRangeLowSrcPort 1.3.6.1.4.1.1872.2.1.10.3.1.8
The lower source TCP/UDP port number to be filtered. It applies only when protocol defined in fltNewCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

fltNewCfgRangeLowDstPort 1.3.6.1.4.1.1872.2.1.10.3.1.9
The lower destination TCP/UDP port number to be filtered. It applies only when protocol defined in fltNewCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

fltNewCfgRangeHighDstPort 1.3.6.1.4.1.1872.2.1.10.3.1.10
The higher destination TCP/UDP port number to be filtered. It applies only when protocol defined in fltNewCfgProtocol is UDP or TCP. '0' means no filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

fltNewCfgAction 1.3.6.1.4.1.1872.2.1.10.3.1.11
The action for the filtering rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), deny(2), redirect(3), nat(4)  

fltNewCfgRedirPort 1.3.6.1.4.1.1872.2.1.10.3.1.12
The real server port number used for redirection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65534  

fltNewCfgRedirGroup 1.3.6.1.4.1.1872.2.1.10.3.1.13
The real server group to be redirected to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgLog 1.3.6.1.4.1.1872.2.1.10.3.1.14
Enable or disable logging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgState 1.3.6.1.4.1.1872.2.1.10.3.1.15
The state of this filtering rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgDelete 1.3.6.1.4.1.1872.2.1.10.3.1.16
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

fltNewCfgNat 1.3.6.1.4.1.1872.2.1.10.3.1.17
The selection of destination or source for network address translation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER destination-address(1), source-address(2)  

fltNewCfgCache 1.3.6.1.4.1.1872.2.1.10.3.1.18
Enable or disable caching sessions that match filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgInvert 1.3.6.1.4.1.1872.2.1.10.3.1.19
Turn the invert logic on or off for the filter entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invert-on(1), invert-off(2)  

fltNewCfgClientProxy 1.3.6.1.4.1.1872.2.1.10.3.1.20
Enable or disable client proxy.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgTcpAck 1.3.6.1.4.1.1872.2.1.10.3.1.21
Enable or disable filtering on matching TCP ACK and RST flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgUrlRedir 1.3.6.1.4.1.1872.2.1.10.3.1.22
Enable or disable URL redirection. The URL expressions are defined in slbNewCfgUrlTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgSrcMac 1.3.6.1.4.1.1872.2.1.10.3.1.23
The source MAC address to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

fltNewCfgDstMac 1.3.6.1.4.1.1872.2.1.10.3.1.24
The Destination MAC address to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

fltNewCfgFtpNatActive 1.3.6.1.4.1.1872.2.1.10.3.1.25
Enable or disable FTP NAT for active ftp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgAclTcpUrg 1.3.6.1.4.1.1872.2.1.10.3.1.26
Enable or disable TCP URG packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclTcpAck 1.3.6.1.4.1.1872.2.1.10.3.1.27
Enable or disable TCP ACK packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclTcpPsh 1.3.6.1.4.1.1872.2.1.10.3.1.28
Enable or disable TCP PSH packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclTcpRst 1.3.6.1.4.1.1872.2.1.10.3.1.29
Enable or disable TCP RST packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclTcpSyn 1.3.6.1.4.1.1872.2.1.10.3.1.30
Enable or disable TCP SYN packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclTcpFin 1.3.6.1.4.1.1872.2.1.10.3.1.31
Enable or disable TCP FIN packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgAclIcmp 1.3.6.1.4.1.1872.2.1.10.3.1.32
ICMP type to be filtered. A ICMP type of 255 indicates 'any'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fltNewCfgAclIpOption 1.3.6.1.4.1.1872.2.1.10.3.1.33
Enable or disable IP option matching.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fltNewCfgBwmContract 1.3.6.1.4.1.1872.2.1.10.3.1.34
Filt default BW contract number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgAclIpTos 1.3.6.1.4.1.1872.2.1.10.3.1.35
The IP TOS value to be filtered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fltNewCfgAclIpTosMask 1.3.6.1.4.1.1872.2.1.10.3.1.36
The IP TOS mask for filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fltNewCfgAclIpTosNew 1.3.6.1.4.1.1872.2.1.10.3.1.37
The new IP TOS value to over-write when filtering fired.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fltNewCfgFwlb 1.3.6.1.4.1.1872.2.1.10.3.1.38
Enable or disable filtering on firewall redirect hash method.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgNatTimeout 1.3.6.1.4.1.1872.2.1.10.3.1.39
The NAT session timeout. The timeout value should be an even number between (4..30)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 4..30  

fltNewCfgRurl 1.3.6.1.4.1.1872.2.1.10.3.1.40
Enable or disable RURL parsing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgLinklb 1.3.6.1.4.1.1872.2.1.10.3.1.41
Enable or disable WAN link load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgWapRadiusSnoop 1.3.6.1.4.1.1872.2.1.10.3.1.42
Enable or disable WAP RADIUS snooping.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgSrcIpMac 1.3.6.1.4.1.1872.2.1.10.3.1.43
Set a flag indicating whether filtering should be based on the source IP address or the source MAC address field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(1), mac(2)  

fltNewCfgDstIpMac 1.3.6.1.4.1.1872.2.1.10.3.1.44
Set a flag indicating whether filtering should be based on the destination IP address or the destination MAC address field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(1), mac(2)  

fltNewCfgIdslbHash 1.3.6.1.4.1.1872.2.1.10.3.1.45
Set hash parameter for intrusion detection server load balancing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sip(1), dip(2), both(3)  

fltNewCfgVlan 1.3.6.1.4.1.1872.2.1.10.3.1.46
Set the VLAN assoicated with the filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

fltNewCfgName 1.3.6.1.4.1.1872.2.1.10.3.1.47
The name of the filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

fltNewCfgTcpRateLimit 1.3.6.1.4.1.1872.2.1.10.3.1.48
Enable or disable TCP connection rate limiting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgTcpRateMaxConn 1.3.6.1.4.1.1872.2.1.10.3.1.49
Set maximum connections (number of connections in units of 10) for TCP connection rate limiting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

fltNewCfgHash 1.3.6.1.4.1.1872.2.1.10.3.1.50
Set hash parameter for the filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), sip(2), dip(3), both(4), sipsport(5)  

fltNewCfgNasa 1.3.6.1.4.1.1872.2.1.10.3.1.51
Enable or disable NASA redirect to ISD.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgLayer7DenyState 1.3.6.1.4.1.1872.2.1.10.3.1.52
Enable or disable layer 7 deny filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgLayer7DenyUrlBmap 1.3.6.1.4.1.1872.2.1.10.3.1.53
The URL strings selected for Layer 7 deny filters. The selected URL strings are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ URL Path 9 || || || ||___ URL Path 8 || |____ URL Path 7 || . . . ||_________ URL Path 2 |__________ URL Path 1 where x : 1 - The represented URL string is selected 0 - The represented URL string is not selected
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

fltNewCfgLayer7DenyAddUrl 1.3.6.1.4.1.1872.2.1.10.3.1.54
The URL Path (slbCurCfgUrlLbPathIndex) to be added to the Layer 7 deny filter. A zero is returned when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgLayer7DenyRemUrl 1.3.6.1.4.1.1872.2.1.10.3.1.55
The URL Path (slbCurCfgUrlLbPathIndex) to be removed from the Layer 7 deny filter. A zero is returned when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltCurCfgPortTable 1.3.6.1.4.1.1872.2.1.10.4
The filtering port table in the current configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltCurCfgPortTableEntry

fltCurCfgPortTableEntry 1.3.6.1.4.1.1872.2.1.10.4.1
A row in the filtering port table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltCurCfgPortTableEntry  

fltCurCfgPortIndx 1.3.6.1.4.1.1872.2.1.10.4.1.1
The port index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgPortState 1.3.6.1.4.1.1872.2.1.10.4.1.2
Enable or disable filtering.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltCurCfgPortFiltBmap 1.3.6.1.4.1.1872.2.1.10.4.1.3
The filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ filter 9 || || || ||___ filter 8 || |____ filter 7 || . . . ||_________ filter 2 |__________ filter 1 (as index to fltCurCfgTable) where x : 1 - The represented filter rule applied to the port 0 - The represented filter rule not applied to the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

fltNewCfgPortTable 1.3.6.1.4.1.1872.2.1.10.5
The filtering port table in the new configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltNewCfgPortTableEntry

fltNewCfgPortTableEntry 1.3.6.1.4.1.1872.2.1.10.5.1
A row in the filtering port table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltNewCfgPortTableEntry  

fltNewCfgPortIndx 1.3.6.1.4.1.1872.2.1.10.5.1.1
The port index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltNewCfgPortState 1.3.6.1.4.1.1872.2.1.10.5.1.2
Enable or disable filtering.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fltNewCfgPortFiltBmap 1.3.6.1.4.1.1872.2.1.10.5.1.3
The filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ filter 9 || || || ||___ filter 8 || |____ filter 7 || . . . ||_________ filter 2 |__________ filter 1 (as index to fltNewCfgTable) where x : 1 - The represented filter rule applied to the port 0 - The represented filter rule not applied to the port
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

fltNewCfgPortAddFiltRule 1.3.6.1.4.1.1872.2.1.10.5.1.4
This is an action object to add filtering rule to a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule to be added to the port. The range of the valid index is between 1 and fltCurCfgTableMaxSize. When read, the value '0' is returned always.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgPortRemFiltRule 1.3.6.1.4.1.1872.2.1.10.5.1.5
This is an action object to remove filtering rule from a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule to be removed from the port. The range of the valid index is between 1 and fltCurCfgTableMaxSize. When read, the value '0' is returned always.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltCurCfgUrlBwmTable 1.3.6.1.4.1.1872.2.1.10.6
The table of URL based BWM for filtering.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltCurCfgUrlBwmEntry

fltCurCfgUrlBwmEntry 1.3.6.1.4.1.1872.2.1.10.6.1
A row in the URL based BWM filtering table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltCurCfgUrlBwmEntry  

fltCurCfgUrlBwmFltIndex 1.3.6.1.4.1.1872.2.1.10.6.1.1
The number of the filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgUrlBwmUrlId 1.3.6.1.4.1.1872.2.1.10.6.1.2
The URL Path Identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltCurCfgUrlBwmContract 1.3.6.1.4.1.1872.2.1.10.6.1.3
The BW contract.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltNewCfgUrlBwmTable 1.3.6.1.4.1.1872.2.1.10.7
The table of URL based BWM for filtering.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FltNewCfgUrlBwmEntry

fltNewCfgUrlBwmEntry 1.3.6.1.4.1.1872.2.1.10.7.1
A row in the URL based BWM filtering table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FltNewCfgUrlBwmEntry  

fltNewCfgUrlBwmFltIndex 1.3.6.1.4.1.1872.2.1.10.7.1.1
The number of the filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltNewCfgUrlBwmUrlId 1.3.6.1.4.1.1872.2.1.10.7.1.2
The URL Path Identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fltNewCfgUrlBwmContract 1.3.6.1.4.1.1872.2.1.10.7.1.3
The BW traffic contract.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fltNewCfgUrlBwmDelete 1.3.6.1.4.1.1872.2.1.10.7.1.4
When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

fltUrlBwmTableMaxSize 1.3.6.1.4.1.1872.2.1.10.8
The maximum number of URL based BWM entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

gslbCurCfgGenState 1.3.6.1.4.1.1872.2.1.11.1.1
Turn on or off Distributed Server Load Balance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

gslbNewCfgGenState 1.3.6.1.4.1.1872.2.1.11.1.2
Turn on or off Distributed Server Load Balance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

gslbCurCfgGenDnsHandoff 1.3.6.1.4.1.1872.2.1.11.1.3
Enable/Disable DNS handoffs in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenDnsHandoff 1.3.6.1.4.1.1872.2.1.11.1.4
Enable/Disable DNS handoffs in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenDnsTTL 1.3.6.1.4.1.1872.2.1.11.1.5
Time to live value in minute of DNS resource records in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

gslbNewCfgGenDnsTTL 1.3.6.1.4.1.1872.2.1.11.1.6
Time to live value in minute of DNS resource records in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

gslbCurCfgGenHttpRedirect 1.3.6.1.4.1.1872.2.1.11.1.7
Enable/Disable DNS handoffs in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenHttpRedirect 1.3.6.1.4.1.1872.2.1.11.1.8
Enable/Disable DNS handoffs in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenRemSiteUpdateInterval 1.3.6.1.4.1.1872.2.1.11.1.9
The time interval in minute for updating remote site status in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..120  

gslbNewCfgGenRemSiteUpdateInterval 1.3.6.1.4.1.1872.2.1.11.1.10
The time interval in minute for updating remote site status in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..120  

gslbCurCfgGenDnsLocalPref 1.3.6.1.4.1.1872.2.1.11.1.11
Enable/Disable DNS responses with only local addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenDnsLocalPref 1.3.6.1.4.1.1872.2.1.11.1.12
Enable/Disable DNS responses with only local addresses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenMinco 1.3.6.1.4.1.1872.2.1.11.1.13
Minmum number of site connections in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

gslbNewCfgGenMinco 1.3.6.1.4.1.1872.2.1.11.1.14
Minmum number of site connections in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

gslbCurCfgGenOne 1.3.6.1.4.1.1872.2.1.11.1.15
Enable/Disable DNS responses with only one address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenOne 1.3.6.1.4.1.1872.2.1.11.1.16
Enable/Disable DNS responses with only one address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenUsern 1.3.6.1.4.1.1872.2.1.11.1.17
Enable/Disable HTTP redirect to real server name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenUsern 1.3.6.1.4.1.1872.2.1.11.1.18
Enable/Disable HTTP redirect to real server name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenGeo 1.3.6.1.4.1.1872.2.1.11.1.19
Enable/Disable geographic awareness.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenGeo 1.3.6.1.4.1.1872.2.1.11.1.20
Enable/Disable geographic awareness.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenAlways 1.3.6.1.4.1.1872.2.1.11.1.21
Enable/Disable DNS responses with at least one address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenAlways 1.3.6.1.4.1.1872.2.1.11.1.22
Enable/Disable DNS responses with at least one address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenWeight 1.3.6.1.4.1.1872.2.1.11.1.23
Sets the local weight. The higher the weight value, the more connections that will be directed to the local site.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..48  

gslbNewCfgGenWeight 1.3.6.1.4.1.1872.2.1.11.1.24
Sets the local weight. The higher the weight value, the more connections that will be directed to the local site.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..48  

gslbCurCfgGenLookups 1.3.6.1.4.1.1872.2.1.11.4.1
Enable or disable network preference lookups.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenLookups 1.3.6.1.4.1.1872.2.1.11.4.2
Enable or disable network preference lookups.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenLookupDname 1.3.6.1.4.1.1872.2.1.11.4.3
Domain name for internal lookup table
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..34)  

gslbNewCfgGenLookupDname 1.3.6.1.4.1.1872.2.1.11.4.4
Domain name for internal lookup table
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..34)  

gslbNetwork 1.3.6.1.4.1.1872.2.1.11.4.5
OBJECT IDENTIFIER    

gslbCurCfgGenExternal 1.3.6.1.4.1.1872.2.1.11.4.6
Enable or disable external lookups.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbNewCfgGenExternal 1.3.6.1.4.1.1872.2.1.11.4.7
Enable or disable external lookups.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

gslbCurCfgGenEip 1.3.6.1.4.1.1872.2.1.11.4.8
External lookup IP address
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

gslbNewCfgGenEip 1.3.6.1.4.1.1872.2.1.11.4.9
External lookup IP address
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

gslbCurCfgGenLookupPort 1.3.6.1.4.1.1872.2.1.11.4.10
External lookup UDP port number
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 8100..9999  

gslbNewCfgGenLookupPort 1.3.6.1.4.1.1872.2.1.11.4.11
External lookup UDP port number
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 8100..9999  

gslbCurCfgGenLookupTimeout 1.3.6.1.4.1.1872.2.1.11.4.12
External lookup Timeout Interval
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

gslbNewCfgGenLookupTimeout 1.3.6.1.4.1.1872.2.1.11.4.13
External lookup Timeout Interval
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

gslbNetworkTableMaxSize 1.3.6.1.4.1.1872.2.1.11.4.5.1
The maximum number of GSLB Internet network preference entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

gslbCurCfgNetworkTable 1.3.6.1.4.1.1872.2.1.11.4.5.2
The table of Internet network preference in the current_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GslbCurCfgNetworkTableEntry

gslbCurCfgNetworkTableEntry 1.3.6.1.4.1.1872.2.1.11.4.5.2.1
The table about a network preference entry configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GslbCurCfgNetworkTableEntry  

gslbCurCfgNetworkIndx 1.3.6.1.4.1.1872.2.1.11.4.5.2.1.1
The current Internet network preference table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

gslbCurCfgNetworkSourceIp 1.3.6.1.4.1.1872.2.1.11.4.5.2.1.2
The Source IP address of the network table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

gslbCurCfgNetworkNetMask 1.3.6.1.4.1.1872.2.1.11.4.5.2.1.3
The Net mask of the network table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

gslbCurCfgNetworkVip1 1.3.6.1.4.1.1872.2.1.11.4.5.2.1.4
The Vip1 of the network table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

gslbCurCfgNetworkVip2 1.3.6.1.4.1.1872.2.1.11.4.5.2.1.5
The Vip2 of the network table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

gslbNewCfgNetworkTable 1.3.6.1.4.1.1872.2.1.11.4.5.3
The table of Internet network preference in the new_config.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GslbNewCfgNetworkTableEntry

gslbNewCfgNetworkTableEntry 1.3.6.1.4.1.1872.2.1.11.4.5.3.1
The table about a network preference entry configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GslbNewCfgNetworkTableEntry  

gslbNewCfgNetworkIndx 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.1
The new Internet network preference table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

gslbNewCfgNetworkSourceIp 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.2
The Source IP address of the network table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

gslbNewCfgNetworkNetMask 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.3
The Net mask of the network table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

gslbNewCfgNetworkVip1 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.4
The Vip1 of the network table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

gslbNewCfgNetworkVip2 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.5
The Vip2 of the network table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

gslbNewCfgNetworkDelete 1.3.6.1.4.1.1872.2.1.11.4.5.3.1.12
By setting the value to delete(2), the entire row is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2)  

dnsCurCfgPrimaryIpAddr 1.3.6.1.4.1.1872.2.1.11.2.1
The DNS primary IP address in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dnsNewCfgPrimaryIpAddr 1.3.6.1.4.1.1872.2.1.11.2.2
The DNS primary IP address in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE