File: CISCO-IPSLA-TC-MIB.mib (7335 bytes)

Imported modules


Imported symbols


Defined Types

Specifies the type of IP SLA operation to be performed. icmpEcho(1) - The value 'icmpEcho' will cause the IP SLA application to perform a timed ICMP echo request/response operation. udpEcho(2) - The value 'udpEcho' will cause the IP SLA application to perform a timed udp packet send/receive operation. tcpConnect(3) - The value 'tcpConnect' will cause the IP SLA application to perform a timed TCP connect operation. udpJitter(4) - The value 'udpjitter' will cause the IP SLA application to perform delay variance analysis using UDP timestamp packets. icmpjitter(5) - The value 'icmpjitter' will cause the IP SLA application to perform delay variance analysis using ICMP timestamp packets.
  INTEGER icmpEcho(1), udpEcho(2), tcpConnect(3), udpJitter(4), icmpJitter(5)  

Specifies the IP SLA codec type to be used with the UDP jitter operation. The following codec types are defined: notApplicable(0) - no CodecType is defined g711ulaw(1) - uses G.711 U Law 64000 bps g711alaw(2) - uses G.711 A Law 64000 bps g729a(3) - uses G.729 8000 bps
  INTEGER notApplicable(0), g711ulaw(1), g711alaw(2), g729a(3)  

The following are specific reaction variables for an IP SLA operation to react upon: rtt(1) - Round Trip Time jitterSDAvg(2) - Jitter average from source to destination jitterDSAvg(3) - Jitter average from destination to source packetLossSD(4) - Packet loss from source to destination packetLossDS(5) - Packet loss from destination to source mos(6) - Mean Opinion Score timeout(7) - Timeout of the operation connectionLoss(8) - Connection failed to the destination verifyError(9) - Data corruption occurs jitterAvg(10) - Jitter average in both directions icpif(11) - Calculated Planning Impairment Factor packetMIA(12) - Missed packets in operation packetLateArrival(13) - Packets arriving late packetOutOfSequence(14) - Packets arriving out of sequence maxOfPositiveSD(15) - Maximum positive jitter from source to destination maxOfNegativeSD(16) - Maximum negative jitter from source to destination maxOfPositiveDS(17) - Maximum positive jitter from destination to source maxOfNegativeDS(18) - Maximum negative jitter from destination to source. successivePacketLoss(19)- Successive packet dropped maxOfLatencyDS(20) - Maximum Latency from Destination to Source maxOfLatencySD(21) - Maximum Latency from Source to Destination latencyDSAvg(22) - Latency average from Destination to Source latencySDAvg(23) - Latency average from Source to Destination packetLoss(24) - Packets loss in both directions
  INTEGER rtt(1), jitterSDAvg(2), jitterDSAvg(3), packetLossSD(4), packetLossDS(5), mos(6), timeout(7), connectionLoss(8), verifyError(9), jitterAvg(10), icpif(11), packetMIA(12), packetLateArrival(13), packetOutOfSequence(14), maxOfPositiveSD(15), maxOfNegativeSD(16), maxOfPositiveDS(17), maxOfNegativeDS(18), successivePacketLoss(19), maxOfLatencyDS(20), maxOfLatencySD(21), latencyDSAvg(22), latencySDAvg(23), packetLoss(24)  

Defined Values

This MIB contains textual conventions used by CISCO IPSLA MIBs. Acronyms: FEC: Forward Equivalence Class LPD: Label Path Discovery LSP: Label Switched Path MPLS: Multi Protocol Label Switching RTT: Round Trip Time SAA: Service Assurance Agent SLA: Service Level Agreement VPN: Virtual Private Network ICPIF: Calculated Planning Impairment Factor