Nortel-Magellan-Passport-MpaNetworkLinkMIB

File: Nortel-Magellan-Passport-MpaNetworkLinkMIB.mib (291357 bytes)

Imported modules

RFC-1212 Nortel-Magellan-Passport-UsefulDefinitionsMIB Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE components passportMIBs
Counter32 RowPointer DisplayString
StorageType RowStatus PassportCounter64
InterfaceIndex Gauge32 Integer32
Unsigned32 AsciiString Hex
NonReplicated HexString EnterpriseDateAndTime
Link DigitString Unsigned64

Defined Types

MpanlRowStatusEntry  
SEQUENCE    
  mpanlRowStatus RowStatus
  mpanlComponentName DisplayString
  mpanlStorageType StorageType
  mpanlIndex Integer32

MpanlCidDataEntry  
SEQUENCE    
  mpanlCustomerIdentifier Unsigned32

MpanlProvEntry  
SEQUENCE    
  mpanlCommentText AsciiString

MpanlEmissionPriorityQsEntry  
SEQUENCE    
  mpanlNumberOfEmissionQs Unsigned32

MpanlStateEntry  
SEQUENCE    
  mpanlAdminState INTEGER
  mpanlOperationalState INTEGER
  mpanlUsageState INTEGER
  mpanlAvailabilityStatus OCTET STRING
  mpanlProceduralStatus OCTET STRING
  mpanlControlStatus OCTET STRING
  mpanlAlarmStatus OCTET STRING
  mpanlStandbyStatus INTEGER
  mpanlUnknownStatus INTEGER

MpanlStatsEntry  
SEQUENCE    
  mpanlLastUnknownDlci Unsigned32
  mpanlUnknownDlciFramesFromIf Counter32
  mpanlInvalidHeaderFramesFromIf Counter32

MpanlTrafficStatsEntry  
SEQUENCE    
  mpanlFrmToIf Unsigned32
  mpanlOctetToIf Unsigned32
  mpanlFrmFromIf Unsigned32
  mpanlOctetFromIf Unsigned32

MpanlIfEntryEntry  
SEQUENCE    
  mpanlIfAdminStatus INTEGER
  mpanlIfIndex InterfaceIndex

MpanlOperStatusEntry  
SEQUENCE    
  mpanlSnmpOperStatus INTEGER

MpanlOperEntry  
SEQUENCE    
  mpanlRoundTripDelay Unsigned32

MpanlFrmToIfByQueueEntry  
SEQUENCE    
  mpanlFrmToIfByQueueIndex Integer32
  mpanlFrmToIfByQueueValue Unsigned32

MpanlOctetToIfByQueueEntry  
SEQUENCE    
  mpanlOctetToIfByQueueIndex Integer32
  mpanlOctetToIfByQueueValue Unsigned32

MpanlDnaRowStatusEntry  
SEQUENCE    
  mpanlDnaRowStatus RowStatus
  mpanlDnaComponentName DisplayString
  mpanlDnaStorageType StorageType
  mpanlDnaIndex NonReplicated

MpanlDnaOutgoingOptionsEntry  
SEQUENCE    
  mpanlDnaDefaultTransferPriority INTEGER

MpanlDnaCallOptionsEntry  
SEQUENCE    
  mpanlDnaAccountClass Unsigned32
  mpanlDnaAccountCollection OCTET STRING
  mpanlDnaServiceExchange Unsigned32
  mpanlDnaEgressAccounting INTEGER

MpanlFramerRowStatusEntry  
SEQUENCE    
  mpanlFramerRowStatus RowStatus
  mpanlFramerComponentName DisplayString
  mpanlFramerStorageType StorageType
  mpanlFramerIndex NonReplicated

MpanlFramerProvEntry  
SEQUENCE    
  mpanlFramerInterfaceName Link

MpanlFramerLinkEntry  
SEQUENCE    
  mpanlFramerFlagsBetweenFrames Unsigned32

MpanlFramerStateEntry  
SEQUENCE    
  mpanlFramerAdminState INTEGER
  mpanlFramerOperationalState INTEGER
  mpanlFramerUsageState INTEGER

MpanlFramerStatsEntry  
SEQUENCE    
  mpanlFramerFrmToIf Counter32
  mpanlFramerFrmFromIf Counter32
  mpanlFramerOctetFromIf Counter32
  mpanlFramerAborts Counter32
  mpanlFramerCrcErrors Counter32
  mpanlFramerLrcErrors Counter32
  mpanlFramerNonOctetErrors Counter32
  mpanlFramerOverruns Counter32
  mpanlFramerUnderruns Counter32
  mpanlFramerLargeFrmErrors Counter32
  mpanlFramerFrmModeErrors Counter32

MpanlFramerUtilEntry  
SEQUENCE    
  mpanlFramerNormPrioLinkUtilToIf Gauge32
  mpanlFramerNormPrioLinkUtilFromIf Gauge32

MpanlPrefixDnaRowStatusEntry  
SEQUENCE    
  mpanlPrefixDnaRowStatus RowStatus
  mpanlPrefixDnaComponentName DisplayString
  mpanlPrefixDnaStorageType StorageType
  mpanlPrefixDnaNumberingPlanIndicatorIndex INTEGER
  mpanlPrefixDnaDataNetworkAddressIndex DigitString

MpanlDlciRowStatusEntry  
SEQUENCE    
  mpanlDlciRowStatus RowStatus
  mpanlDlciComponentName DisplayString
  mpanlDlciStorageType StorageType
  mpanlDlciIndex Integer32

MpanlDlciStateEntry  
SEQUENCE    
  mpanlDlciAdminState INTEGER
  mpanlDlciOperationalState INTEGER
  mpanlDlciUsageState INTEGER
  mpanlDlciAvailabilityStatus OCTET STRING
  mpanlDlciProceduralStatus OCTET STRING
  mpanlDlciControlStatus OCTET STRING
  mpanlDlciAlarmStatus OCTET STRING
  mpanlDlciStandbyStatus INTEGER
  mpanlDlciUnknownStatus INTEGER

MpanlDlciCalldEntry  
SEQUENCE    
  mpanlDlciQ933CallState INTEGER
  mpanlDlciQ933CallReference Unsigned32

MpanlDlciSpOpEntry  
SEQUENCE    
  mpanlDlciMaximumFrameSize Unsigned32
  mpanlDlciCommittedBurstSize Unsigned32
  mpanlDlciExcessBurstSize Unsigned32
  mpanlDlciAccounting INTEGER
  mpanlDlciEmissionPriorityToIf INTEGER
  mpanlDlciTransferPriToNwk Unsigned32
  mpanlDlciTransferPriFromNwk Unsigned32

MpanlDlciStatsEntry  
SEQUENCE    
  mpanlDlciFrmToIf Unsigned32
  mpanlDlciFecnFrmToIf Unsigned32
  mpanlDlciBecnFrmToIf Unsigned32
  mpanlDlciBciToSubnet Unsigned32
  mpanlDlciDeFrmToIf Unsigned32
  mpanlDlciDiscCongestedToIf Unsigned32
  mpanlDlciDiscDeCongestedToIf Unsigned32
  mpanlDlciFrmFromIf Unsigned32
  mpanlDlciFecnFrmFromIf Unsigned32
  mpanlDlciBecnFrmFromIf Unsigned32
  mpanlDlciFciFromSubnet Unsigned32
  mpanlDlciBciFromSubnet Unsigned32
  mpanlDlciDeFrmFromIf Unsigned32
  mpanlDlciExcessFrmFromIf Unsigned32
  mpanlDlciDiscExcessFromIf Unsigned32
  mpanlDlciDiscFrameAbit Unsigned32
  mpanlDlciDiscCongestedFromIf Unsigned32
  mpanlDlciDiscDeCongestedFromIf Unsigned32
  mpanlDlciErrorShortFrmFromIf Unsigned32
  mpanlDlciErrorLongFrmFromIf Unsigned32
  mpanlDlciBecnFrmSetByService Unsigned32
  mpanlDlciBytesToIf Unsigned32
  mpanlDlciDeBytesToIf Unsigned32
  mpanlDlciDiscCongestedToIfBytes Unsigned32
  mpanlDlciDiscDeCongestedToIfBytes Unsigned32
  mpanlDlciBytesFromIf Unsigned32
  mpanlDlciDeBytesFromIf Unsigned32
  mpanlDlciExcessBytesFromIf Unsigned32
  mpanlDlciDiscExcessFromIfBytes Unsigned32
  mpanlDlciDiscByteAbit Unsigned32
  mpanlDlciDiscCongestedFromIfBytes Unsigned32
  mpanlDlciDiscDeCongestedFromIfBytes Unsigned32
  mpanlDlciErrorLongBytesFromIf Unsigned32
  mpanlDlciTransferPriorityToNetwork INTEGER
  mpanlDlciTransferPriorityFromNetwork INTEGER

MpanlDlciIntEntry  
SEQUENCE    
  mpanlDlciStartTime EnterpriseDateAndTime
  mpanlDlciTotalIngressBytes Unsigned64
  mpanlDlciTotalEgressBytes Unsigned64
  mpanlDlciEirIngressBytes Unsigned64
  mpanlDlciEirEgressBytes Unsigned64
  mpanlDlciDiscardedBytes Unsigned64
  mpanlDlciTotalIngressSegFrm Unsigned32
  mpanlDlciTotalEgressSegFrm Unsigned32
  mpanlDlciEirIngressSegFrm Unsigned32
  mpanlDlciEirEgressSegFrm Unsigned32
  mpanlDlciDiscardedSegFrm Unsigned32
  mpanlDlciCallReferenceNumber Unsigned32
  mpanlDlciElapsedDifference Unsigned32

MpanlDlciAbitEntry  
SEQUENCE    
  mpanlDlciABitStatusToIf INTEGER
  mpanlDlciABitReasonToIf INTEGER
  mpanlDlciABitStatusFromIf INTEGER
  mpanlDlciABitReasonFromIf INTEGER
  mpanlDlciLoopbackState INTEGER

MpanlDlciLbRowStatusEntry  
SEQUENCE    
  mpanlDlciLbRowStatus RowStatus
  mpanlDlciLbComponentName DisplayString
  mpanlDlciLbStorageType StorageType
  mpanlDlciLbIndex NonReplicated

MpanlDlciLbStatsEntry  
SEQUENCE    
  mpanlDlciLbLocalTotalFrm Unsigned32
  mpanlDlciLbLocalTotalBytes Unsigned32
  mpanlDlciLbLocalFecnFrm Unsigned32
  mpanlDlciLbLocalBecnFrm Unsigned32
  mpanlDlciLbLocalDeFrm Unsigned32
  mpanlDlciLbLocalDeBytes Unsigned32
  mpanlDlciLbRemoteTotalFrm Unsigned32
  mpanlDlciLbRemoteTotalBytes Unsigned32
  mpanlDlciLbRemoteFecnFrm Unsigned32
  mpanlDlciLbRemoteBecnFrm Unsigned32
  mpanlDlciLbRemoteDeFrm Unsigned32
  mpanlDlciLbRemoteDeBytes Unsigned32

MpanlDlciVcRowStatusEntry  
SEQUENCE    
  mpanlDlciVcRowStatus RowStatus
  mpanlDlciVcComponentName DisplayString
  mpanlDlciVcStorageType StorageType
  mpanlDlciVcIndex NonReplicated

MpanlDlciVcCadEntry  
SEQUENCE    
  mpanlDlciVcType INTEGER
  mpanlDlciVcState INTEGER
  mpanlDlciVcPreviousState INTEGER
  mpanlDlciVcDiagnosticCode Unsigned32
  mpanlDlciVcPreviousDiagnosticCode Unsigned32
  mpanlDlciVcCalledNpi INTEGER
  mpanlDlciVcCalledDna DigitString
  mpanlDlciVcCalledLcn Unsigned32
  mpanlDlciVcCallingNpi INTEGER
  mpanlDlciVcCallingDna DigitString
  mpanlDlciVcCallingLcn Unsigned32
  mpanlDlciVcAccountingEnabled INTEGER
  mpanlDlciVcFastSelectCall INTEGER
  mpanlDlciVcPathReliability INTEGER
  mpanlDlciVcAccountingEnd INTEGER
  mpanlDlciVcPriority INTEGER
  mpanlDlciVcSegmentSize Unsigned32
  mpanlDlciVcMaxSubnetPktSize Unsigned32
  mpanlDlciVcRcosToNetwork INTEGER
  mpanlDlciVcRcosFromNetwork INTEGER
  mpanlDlciVcEmissionPriorityToNetwork INTEGER
  mpanlDlciVcEmissionPriorityFromNetwork INTEGER
  mpanlDlciVcDataPath AsciiString

MpanlDlciVcIntdEntry  
SEQUENCE    
  mpanlDlciVcCallReferenceNumber Hex
  mpanlDlciVcElapsedTimeTillNow Unsigned32
  mpanlDlciVcSegmentsRx Unsigned32
  mpanlDlciVcSegmentsSent Unsigned32
  mpanlDlciVcStartTime EnterpriseDateAndTime

MpanlDlciVcFrdEntry  
SEQUENCE    
  mpanlDlciVcFrmCongestedToSubnet Unsigned32
  mpanlDlciVcCannotForwardToSubnet Unsigned32
  mpanlDlciVcNotDataXferToSubnet Unsigned32
  mpanlDlciVcOutOfRangeFrmFromSubnet Unsigned32
  mpanlDlciVcCombErrorsFromSubnet Unsigned32
  mpanlDlciVcDuplicatesFromSubnet Unsigned32
  mpanlDlciVcNotDataXferFromSubnet Unsigned32
  mpanlDlciVcFrmLossTimeouts Unsigned32
  mpanlDlciVcOoSeqByteCntExceeded Unsigned32
  mpanlDlciVcPeakOoSeqPktCount Unsigned32
  mpanlDlciVcPeakOoSeqFrmForwarded Unsigned32
  mpanlDlciVcSendSequenceNumber Unsigned32
  mpanlDlciVcPktRetryTimeouts Unsigned32
  mpanlDlciVcPeakRetryQueueSize Unsigned32
  mpanlDlciVcSubnetRecoveries Unsigned32
  mpanlDlciVcOoSeqPktCntExceeded Unsigned32
  mpanlDlciVcPeakOoSeqByteCount Unsigned32

MpanlDlciVcDmepEntry  
SEQUENCE    
  mpanlDlciVcDmepValue RowPointer

MpanlDlciLCoRowStatusEntry  
SEQUENCE    
  mpanlDlciLCoRowStatus RowStatus
  mpanlDlciLCoComponentName DisplayString
  mpanlDlciLCoStorageType StorageType
  mpanlDlciLCoIndex NonReplicated

MpanlDlciLCoPathDataEntry  
SEQUENCE    
  mpanlDlciLCoState INTEGER
  mpanlDlciLCoEnd INTEGER
  mpanlDlciLCoCostMetric Unsigned32
  mpanlDlciLCoDelayMetric Unsigned32
  mpanlDlciLCoRoundTripDelay Unsigned32
  mpanlDlciLCoSetupPriority Unsigned32
  mpanlDlciLCoHoldingPriority Unsigned32
  mpanlDlciLCoRequiredTxBandwidth Gauge32
  mpanlDlciLCoRequiredRxBandwidth Gauge32
  mpanlDlciLCoRequiredTrafficType INTEGER
  mpanlDlciLCoPermittedTrunkTypes OCTET STRING
  mpanlDlciLCoRequiredSecurity Unsigned32
  mpanlDlciLCoRequiredCustomerParameter Unsigned32
  mpanlDlciLCoEmissionPriority Unsigned32
  mpanlDlciLCoDiscardPriority Unsigned32
  mpanlDlciLCoRetryCount Unsigned32
  mpanlDlciLCoPathFailureCount Unsigned32
  mpanlDlciLCoReasonForNoRoute INTEGER
  mpanlDlciLCoLastTearDownReason INTEGER
  mpanlDlciLCoPathFailureAction INTEGER
  mpanlDlciLCoBumpPreference INTEGER
  mpanlDlciLCoOptimization INTEGER
  mpanlDlciLCoPathUpDateTime EnterpriseDateAndTime

MpanlDlciLCoStatsEntry  
SEQUENCE    
  mpanlDlciLCoPktsToNetwork PassportCounter64
  mpanlDlciLCoBytesToNetwork PassportCounter64
  mpanlDlciLCoPktsFromNetwork PassportCounter64
  mpanlDlciLCoBytesFromNetwork PassportCounter64

MpanlDlciLCoCallDataEntry  
SEQUENCE    
  mpanlDlciLCoCallingNpi INTEGER
  mpanlDlciLCoCallingDna DigitString
  mpanlDlciLCoElapsedTimeTillNow Unsigned32
  mpanlDlciLCoCallReferenceNumber Hex
  mpanlDlciLCoCalledNpi INTEGER
  mpanlDlciLCoCalledDna DigitString

MpanlDlciLCoPathEntry  
SEQUENCE    
  mpanlDlciLCoPathValue AsciiString

MpanlDlciJvcRowStatusEntry  
SEQUENCE    
  mpanlDlciJvcRowStatus RowStatus
  mpanlDlciJvcComponentName DisplayString
  mpanlDlciJvcStorageType StorageType
  mpanlDlciJvcIndex NonReplicated

MpanlDlciJvcOperEntry  
SEQUENCE    
  mpanlDlciJvcCurrentState INTEGER
  mpanlDlciJvcPreviousState INTEGER
  mpanlDlciJvcCallingNpi INTEGER
  mpanlDlciJvcCallingAddress DigitString
  mpanlDlciJvcCallingLcn Unsigned32
  mpanlDlciJvcCalledNpi INTEGER
  mpanlDlciJvcCalledAddress DigitString
  mpanlDlciJvcCalledLcn Unsigned32

MpanlDlciJvcStatEntry  
SEQUENCE    
  mpanlDlciJvcPacketsFromSubnet Unsigned32
  mpanlDlciJvcPacketsToSubnet Unsigned32
  mpanlDlciJvcPacketsDiscarded Unsigned32
  mpanlDlciJvcProtocolErrors Unsigned32

MpanlSigRowStatusEntry  
SEQUENCE    
  mpanlSigRowStatus RowStatus
  mpanlSigComponentName DisplayString
  mpanlSigStorageType StorageType
  mpanlSigIndex NonReplicated

MpanlSigSysParmsEntry  
SEQUENCE    
  mpanlSigCallSetupTimer Unsigned32
  mpanlSigDisconnectTimer Unsigned32
  mpanlSigReleaseTimer Unsigned32
  mpanlSigCallProceedingTimer Unsigned32
  mpanlSigNetworkType INTEGER

MpanlSigLapfSysEntry  
SEQUENCE    
  mpanlSigWindowSize Unsigned32
  mpanlSigRetransmitLimit Unsigned32
  mpanlSigAckTimer Unsigned32
  mpanlSigAckDelayTimer Unsigned32
  mpanlSigIdleProbeTimer Unsigned32

MpanlSigSvcaccEntry  
SEQUENCE    
  mpanlSigDefaultAccounting INTEGER

MpanlSigStateEntry  
SEQUENCE    
  mpanlSigAdminState INTEGER
  mpanlSigOperationalState INTEGER
  mpanlSigUsageState INTEGER

MpanlSigStatsEntry  
SEQUENCE    
  mpanlSigCurrentNumberOfSvcCalls Unsigned32
  mpanlSigInCalls Counter32
  mpanlSigInCallsRefused Counter32
  mpanlSigOutCalls Counter32
  mpanlSigOutCallsFailed Counter32
  mpanlSigProtocolErrors Counter32
  mpanlSigQualityOfServiceNotAvailable Counter32
  mpanlSigSetupTimeout Counter32
  mpanlSigLastCauseInStatusMsgReceived Unsigned32
  mpanlSigLastStateInStatusMsgReceived INTEGER
  mpanlSigLastDlciReceivedStatus Unsigned32
  mpanlSigLastQ933StateReceivedStatus INTEGER
  mpanlSigLastTimeMsgBlockCongested EnterpriseDateAndTime
  mpanlSigLastDlciWithMsgBlockCongestion Unsigned32

MpanlSigLapfStatusEntry  
SEQUENCE    
  mpanlSigCurrentState INTEGER
  mpanlSigLastStateChangeReason INTEGER
  mpanlSigFrmrReceive HexString
  mpanlSigCurrentQueueSize Counter32

MpanlSigLapfStatsEntry  
SEQUENCE    
  mpanlSigStateChange Counter32
  mpanlSigRemoteBusy Counter32
  mpanlSigReceiveRejectFrame Counter32
  mpanlSigAckTimeout Counter32
  mpanlSigIFramesTransmitted Counter32
  mpanlSigIFramesTxDiscarded Counter32
  mpanlSigIFramesReceived Counter32
  mpanlSigIFramesRcvdDiscarded Counter32

MpanlSigMpanlRowStatusEntry  
SEQUENCE    
  mpanlSigMpanlRowStatus RowStatus
  mpanlSigMpanlComponentName DisplayString
  mpanlSigMpanlStorageType StorageType
  mpanlSigMpanlIndex NonReplicated

MpanlSigMpanlStateEntry  
SEQUENCE    
  mpanlSigMpanlAdminState INTEGER
  mpanlSigMpanlOperationalState INTEGER
  mpanlSigMpanlUsageState INTEGER

MpanlSigMpanlProfileEntry  
SEQUENCE    
  mpanlSigMpanlDteCustomerId Unsigned32
  mpanlSigMpanlDteNodeId Unsigned32
  mpanlSigMpanlDteComponentName AsciiString
  mpanlSigMpanlHighestDlci Unsigned32

MpanlSigMpanlStatsEntry  
SEQUENCE    
  mpanlSigMpanlProtocolErrors Counter32
  mpanlSigMpanlSap0CommandsRx Counter32
  mpanlSigMpanlSap0CommandsTx Counter32
  mpanlSigMpanlSapXCommandsRx Counter32
  mpanlSigMpanlSapXCommandsTx Counter32

MpanlSigMpanlLapfStatusEntry  
SEQUENCE    
  mpanlSigMpanlCurrentState INTEGER
  mpanlSigMpanlLastStateChangeReason INTEGER
  mpanlSigMpanlFrmrReceive HexString
  mpanlSigMpanlCurrentQueueSize Counter32

MpanlSigMpanlLapfStatsEntry  
SEQUENCE    
  mpanlSigMpanlStateChange Counter32
  mpanlSigMpanlRemoteBusy Counter32
  mpanlSigMpanlReceiveRejectFrame Counter32
  mpanlSigMpanlAckTimeout Counter32
  mpanlSigMpanlIFramesTransmitted Counter32
  mpanlSigMpanlIFramesTxDiscarded Counter32
  mpanlSigMpanlIFramesReceived Counter32
  mpanlSigMpanlIFramesRcvdDiscarded Counter32

MpanlLmiRowStatusEntry  
SEQUENCE    
  mpanlLmiRowStatus RowStatus
  mpanlLmiComponentName DisplayString
  mpanlLmiStorageType StorageType
  mpanlLmiIndex NonReplicated

MpanlLmiParmsEntry  
SEQUENCE    
  mpanlLmiProcedures INTEGER

MpanlLmiStateEntry  
SEQUENCE    
  mpanlLmiAdminState INTEGER
  mpanlLmiOperationalState INTEGER
  mpanlLmiUsageState INTEGER

MpanlVoFrRowStatusEntry  
SEQUENCE    
  mpanlVoFrRowStatus RowStatus
  mpanlVoFrComponentName DisplayString
  mpanlVoFrStorageType StorageType
  mpanlVoFrIndex NonReplicated

MpanlVoFrOperEntry  
SEQUENCE    
  mpanlVoFrMaximumFrameSize Counter32
  mpanlVoFrTransmitInformationRate Counter32

MpanlVoFrStatsEntry  
SEQUENCE    
  mpanlVoFrFragmentedHighestPriorityFrames Counter32
  mpanlVoFrLostFragmentsFromIf Counter32
  mpanlVoFrProtocolViolationsFromIf Counter32

MpanlFrMuxSetupRowStatusEntry  
SEQUENCE    
  mpanlFrMuxSetupRowStatus RowStatus
  mpanlFrMuxSetupComponentName DisplayString
  mpanlFrMuxSetupStorageType StorageType
  mpanlFrMuxSetupIndex NonReplicated

MpanlFrMuxSetupOpEntry  
SEQUENCE    
  mpanlFrMuxSetupCommittedInformationRate Unsigned32
  mpanlFrMuxSetupDlciCompName RowPointer

MpanlFrMuxSetupPvcSetupRowStatusEntry  
SEQUENCE    
  mpanlFrMuxSetupPvcSetupRowStatus RowStatus
  mpanlFrMuxSetupPvcSetupComponentName DisplayString
  mpanlFrMuxSetupPvcSetupStorageType StorageType
  mpanlFrMuxSetupPvcSetupIndex NonReplicated

MpanlFrMuxSetupPvcSetupProvEntry  
SEQUENCE    
  mpanlFrMuxSetupPvcSetupDlciName Link

MpanlIsdnRowStatusEntry  
SEQUENCE    
  mpanlIsdnRowStatus RowStatus
  mpanlIsdnComponentName DisplayString
  mpanlIsdnStorageType StorageType
  mpanlIsdnIndex NonReplicated

MpanlIsdnProvEntry  
SEQUENCE    
  mpanlIsdnT320 Unsigned32
  mpanlIsdnAddressSignalling INTEGER

MpanlIsdnOperEntry  
SEQUENCE    
  mpanlIsdnDataSigChan INTEGER
  mpanlIsdnBChannelState INTEGER
  mpanlIsdnLastUsedCgpn DigitString
  mpanlIsdnBChanIntState INTEGER
  mpanlIsdnActiveVirtualCircuitsCount Counter32

Defined Values

mpaNetworkLinkMIB 1.1.562.2.4.2.119
OBJECT IDENTIFIER    

mpanl 1.1.562.2.4.1.123
OBJECT IDENTIFIER    

mpanlRowStatusTable 1.1.562.2.4.1.123.1
This entry controls the addition and deletion of mpanl components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlRowStatusEntry

mpanlRowStatusEntry 1.1.562.2.4.1.123.1.1
A single entry in the table represents a single mpanl component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlRowStatusEntry  

mpanlRowStatus 1.1.562.2.4.1.123.1.1.1
This variable is used as the basis for SNMP naming of mpanl components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mpanlComponentName 1.1.562.2.4.1.123.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlStorageType 1.1.562.2.4.1.123.1.1.4
This variable represents the storage type value for the mpanl tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlIndex 1.1.562.2.4.1.123.1.1.10
This variable represents the index for the mpanl tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

mpanlCidDataTable 1.1.562.2.4.1.123.10
This group contains the attribute for the MPANL component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlCidDataEntry

mpanlCidDataEntry 1.1.562.2.4.1.123.10.1
An entry in the mpanlCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlCidDataEntry  

mpanlCustomerIdentifier 1.1.562.2.4.1.123.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mpanlProvTable 1.1.562.2.4.1.123.12
This group contains provisionable attributes of the MPANL service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlProvEntry

mpanlProvEntry 1.1.562.2.4.1.123.12.1
An entry in the mpanlProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlProvEntry  

mpanlCommentText 1.1.562.2.4.1.123.12.1.1
This attribute specifies the name the customer wishes to associate with this MPANL interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..40)  

mpanlEmissionPriorityQsTable 1.1.562.2.4.1.123.13
This group contains the provisionable attribute to specifie the number of Frame Relay egress emission priority queues to be used on that Frame Relay Interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlEmissionPriorityQsEntry

mpanlEmissionPriorityQsEntry 1.1.562.2.4.1.123.13.1
An entry in the mpanlEmissionPriorityQsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlEmissionPriorityQsEntry  

mpanlNumberOfEmissionQs 1.1.562.2.4.1.123.13.1.1
This attribute specifies the number of egress emission priority queues that will be used for that Frame Relay interface. The possible values of this attribute are 2 or 4: For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible values are: 2 (in which case they are hardware queues), or 4 (in which case they are software queues). For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases they are software queues).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 2 | 4  

mpanlStateTable 1.1.562.2.4.1.123.14
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlStateEntry

mpanlStateEntry 1.1.562.2.4.1.123.14.1
An entry in the mpanlStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlStateEntry  

mpanlAdminState 1.1.562.2.4.1.123.14.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mpanlOperationalState 1.1.562.2.4.1.123.14.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlUsageState 1.1.562.2.4.1.123.14.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mpanlAvailabilityStatus 1.1.562.2.4.1.123.14.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mpanlProceduralStatus 1.1.562.2.4.1.123.14.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlControlStatus 1.1.562.2.4.1.123.14.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlAlarmStatus 1.1.562.2.4.1.123.14.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlStandbyStatus 1.1.562.2.4.1.123.14.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mpanlUnknownStatus 1.1.562.2.4.1.123.14.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mpanlStatsTable 1.1.562.2.4.1.123.16
FrUni/n Statistics This group contains the statistics about the operational behavior of the service at the interface level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlStatsEntry

mpanlStatsEntry 1.1.562.2.4.1.123.16.1
An entry in the mpanlStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlStatsEntry  

mpanlLastUnknownDlci 1.1.562.2.4.1.123.16.1.1
This attribute identifies the most recent DLCI which user frames were received on for which a DLCI has not been provisioned on the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..1023  

mpanlUnknownDlciFramesFromIf 1.1.562.2.4.1.123.16.1.2
This attribute contains a count of the number of frames received from the interface with an unknown DLCI (DLCI which is not provisioned). When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlInvalidHeaderFramesFromIf 1.1.562.2.4.1.123.16.1.3
This attribute counts the number of frames received from the interface with an invalid header format. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlTrafficStatsTable 1.1.562.2.4.1.123.17
This operational group provides the traffic statistics of the service at the interface level. Each attribute type is a non-negative integer which monotonically increases until it reaches a maximum value, at which point it wraps around and starts increasing again from zero.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlTrafficStatsEntry

mpanlTrafficStatsEntry 1.1.562.2.4.1.123.17.1
An entry in the mpanlTrafficStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlTrafficStatsEntry  

mpanlFrmToIf 1.1.562.2.4.1.123.17.1.1
This attribute counts frames transmitted to the interface. This count may differ from its framer couterpart because Voice over Frame Relay function may fragment and pack the Frame Relay frames before transmission. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlOctetToIf 1.1.562.2.4.1.123.17.1.2
This attribute counts octets transmitted to the interface. This count may differ from its framer couterpart because Voice over Frame Relay function may fragment and pack the Frame Relay frames before transmission. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlFrmFromIf 1.1.562.2.4.1.123.17.1.3
This attribute counts frames received from the interface. This count may differ from its framer couterpart because Voice over Frame Relay function may fragment and pack the Frame Relay frames before transmission. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlOctetFromIf 1.1.562.2.4.1.123.17.1.4
This attribute counts octets received from the interface. This count may differ from its framer couterpart because Voice over Frame Relay function may fragment and pack the Frame Relay frames before transmission. When the maximum is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlIfEntryTable 1.1.562.2.4.1.123.23
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlIfEntryEntry

mpanlIfEntryEntry 1.1.562.2.4.1.123.23.1
An entry in the mpanlIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlIfEntryEntry  

mpanlIfAdminStatus 1.1.562.2.4.1.123.23.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mpanlIfIndex 1.1.562.2.4.1.123.23.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mpanlOperStatusTable 1.1.562.2.4.1.123.24
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlOperStatusEntry

mpanlOperStatusEntry 1.1.562.2.4.1.123.24.1
An entry in the mpanlOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlOperStatusEntry  

mpanlSnmpOperStatus 1.1.562.2.4.1.123.24.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mpanlOperTable 1.1.562.2.4.1.123.25
This group contains miscelleneous operational attributes of the MPANL service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlOperEntry

mpanlOperEntry 1.1.562.2.4.1.123.25.1
An entry in the mpanlOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlOperEntry  

mpanlRoundTripDelay 1.1.562.2.4.1.123.25.1.1
This attribute indicates the round trip delay of the MPANL interface. The round trip delay measurement is only made when this attribute is displayed. The measured value is rounded up to the next millisecond. This attribute has the value 0, if the delay measurement cannot be made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..10000  

mpanlFrmToIfByQueueTable 1.1.562.2.4.1.123.350
This attribute counts the total number of frames transmitted to the interface per egress emission priority queue since the component has been activated. There is potentially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFrmToIfByQueueEntry

mpanlFrmToIfByQueueEntry 1.1.562.2.4.1.123.350.1
An entry in the mpanlFrmToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFrmToIfByQueueEntry  

mpanlFrmToIfByQueueIndex 1.1.562.2.4.1.123.350.1.1
This variable represents the index for the mpanlFrmToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..3  

mpanlFrmToIfByQueueValue 1.1.562.2.4.1.123.350.1.2
This variable represents an individual value for the mpanlFrmToIfByQueueTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlOctetToIfByQueueTable 1.1.562.2.4.1.123.351
This attribute counts the total number of octets transmitted from the service to the interface per emission priority queue since the component has been activated. There is potentially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlOctetToIfByQueueEntry

mpanlOctetToIfByQueueEntry 1.1.562.2.4.1.123.351.1
An entry in the mpanlOctetToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlOctetToIfByQueueEntry  

mpanlOctetToIfByQueueIndex 1.1.562.2.4.1.123.351.1.1
This variable represents the index for the mpanlOctetToIfByQueueTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..3  

mpanlOctetToIfByQueueValue 1.1.562.2.4.1.123.351.1.2
This variable represents an individual value for the mpanlOctetToIfByQueueTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDna 1.1.562.2.4.1.123.2
OBJECT IDENTIFIER    

mpanlDnaRowStatusTable 1.1.562.2.4.1.123.2.1
This entry controls the addition and deletion of mpanlDna components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDnaRowStatusEntry

mpanlDnaRowStatusEntry 1.1.562.2.4.1.123.2.1.1
A single entry in the table represents a single mpanlDna component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDnaRowStatusEntry  

mpanlDnaRowStatus 1.1.562.2.4.1.123.2.1.1.1
This variable is used as the basis for SNMP naming of mpanlDna components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDnaComponentName 1.1.562.2.4.1.123.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDnaStorageType 1.1.562.2.4.1.123.2.1.1.4
This variable represents the storage type value for the mpanlDna tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDnaIndex 1.1.562.2.4.1.123.2.1.1.10
This variable represents the index for the mpanlDna tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlDnaOutgoingOptionsTable 1.1.562.2.4.1.123.2.11
DnaOutOptionsProv group defines call options of a Dna for calls which are made out of the interface represented by Dna. All these options are not used for calls arriving to the interface represented by Dna.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDnaOutgoingOptionsEntry

mpanlDnaOutgoingOptionsEntry 1.1.562.2.4.1.123.2.11.1
An entry in the mpanlDnaOutgoingOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDnaOutgoingOptionsEntry  

mpanlDnaDefaultTransferPriority 1.1.562.2.4.1.123.2.11.1.18
This attribute specifies the default transfer priority to network for all outgoing calls using this particular Dna. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default defaultTransferPriority is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

mpanlDnaCallOptionsTable 1.1.562.2.4.1.123.2.13
DnaCallOptions group defines additional options for calls not related directly to direction of a call.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDnaCallOptionsEntry

mpanlDnaCallOptionsEntry 1.1.562.2.4.1.123.2.13.1
An entry in the mpanlDnaCallOptionsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDnaCallOptionsEntry  

mpanlDnaAccountClass 1.1.562.2.4.1.123.2.13.1.10
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator. This attribute is returned by the local VC in the accounting record for all calls setup using this particular DNA.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDnaAccountCollection 1.1.562.2.4.1.123.2.13.1.11
This set attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. The force option is available for X.75 Gateways only. If none of these reasons are set, then accounting will be suppressed. To set a specific accounting collection reason, the reason is entered and the corresponding bit in the structure is set to a value of 1. To turn off a specific accounting collection reason, the reason is entered preceeded with the '^' character, and the corresponding bit in the structure is set to a value of 0. The bit placement for the accounting collection reasons is as follows: Bit 0 - Bill Bit 1 - Test Bit 2 - Study Bit 3 - Audit Bit 4 - Force Description of bits: bill(0) test(1) study(2) audit(3) force(4)
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlDnaServiceExchange 1.1.562.2.4.1.123.2.13.1.12
This attribute is an arbitrary number, Data Service Exchange, as entered by the network operator and reported in accounting record. It is converted into an internal 8-bit integer value for use in the accounting record as well as in various X.25 and X.75 Tariff utilities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDnaEgressAccounting 1.1.562.2.4.1.123.2.13.1.13
This attribute specifies if Egress accounting is enabled by the MPANL service. Disabling of Egress accounting means that only segment counts are collected by VC and there are no frame relay counts in accounting records for the MPANL service. Enabling of Egress accounting means that the accounting records for MPANL contain frame relay specific counts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mpanlFramer 1.1.562.2.4.1.123.3
OBJECT IDENTIFIER    

mpanlFramerRowStatusTable 1.1.562.2.4.1.123.3.1
This entry controls the addition and deletion of mpanlFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerRowStatusEntry

mpanlFramerRowStatusEntry 1.1.562.2.4.1.123.3.1.1
A single entry in the table represents a single mpanlFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerRowStatusEntry  

mpanlFramerRowStatus 1.1.562.2.4.1.123.3.1.1.1
This variable is used as the basis for SNMP naming of mpanlFramer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mpanlFramerComponentName 1.1.562.2.4.1.123.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlFramerStorageType 1.1.562.2.4.1.123.3.1.1.4
This variable represents the storage type value for the mpanlFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlFramerIndex 1.1.562.2.4.1.123.3.1.1.10
This variable represents the index for the mpanlFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlFramerProvTable 1.1.562.2.4.1.123.3.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerProvEntry

mpanlFramerProvEntry 1.1.562.2.4.1.123.3.10.1
An entry in the mpanlFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerProvEntry  

mpanlFramerInterfaceName 1.1.562.2.4.1.123.3.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mpanlFramerLinkTable 1.1.562.2.4.1.123.3.11
This group contains attributes defining the framing of data on the link interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerLinkEntry

mpanlFramerLinkEntry 1.1.562.2.4.1.123.3.11.1
An entry in the mpanlFramerLinkTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerLinkEntry  

mpanlFramerFlagsBetweenFrames 1.1.562.2.4.1.123.3.11.1.4
This attribute defines the number of flags that are inserted between frames sent to the link interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..16  

mpanlFramerStateTable 1.1.562.2.4.1.123.3.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerStateEntry

mpanlFramerStateEntry 1.1.562.2.4.1.123.3.12.1
An entry in the mpanlFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerStateEntry  

mpanlFramerAdminState 1.1.562.2.4.1.123.3.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mpanlFramerOperationalState 1.1.562.2.4.1.123.3.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlFramerUsageState 1.1.562.2.4.1.123.3.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mpanlFramerStatsTable 1.1.562.2.4.1.123.3.13
This group contains the operational statistics data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerStatsEntry

mpanlFramerStatsEntry 1.1.562.2.4.1.123.3.13.1
An entry in the mpanlFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerStatsEntry  

mpanlFramerFrmToIf 1.1.562.2.4.1.123.3.13.1.1
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerFrmFromIf 1.1.562.2.4.1.123.3.13.1.2
The number of frames received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerOctetFromIf 1.1.562.2.4.1.123.3.13.1.3
The number of bytes received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerAborts 1.1.562.2.4.1.123.3.13.1.4
This attribute is the total number of aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerCrcErrors 1.1.562.2.4.1.123.3.13.1.5
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerLrcErrors 1.1.562.2.4.1.123.3.13.1.6
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerNonOctetErrors 1.1.562.2.4.1.123.3.13.1.7
This attribute is the total number of frames that were non octet aligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerOverruns 1.1.562.2.4.1.123.3.13.1.8
This attribute is the total number of frames received from the link for which overruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerUnderruns 1.1.562.2.4.1.123.3.13.1.9
This attribute is the total number of frames transmitted to the link for which underruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerLargeFrmErrors 1.1.562.2.4.1.123.3.13.1.10
This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerFrmModeErrors 1.1.562.2.4.1.123.3.13.1.11
This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlFramerUtilTable 1.1.562.2.4.1.123.3.14
This group contains the link utilizaiton operational data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlFramerUtilEntry

mpanlFramerUtilEntry 1.1.562.2.4.1.123.3.14.1
An entry in the mpanlFramerUtilTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlFramerUtilEntry  

mpanlFramerNormPrioLinkUtilToIf 1.1.562.2.4.1.123.3.14.1.1
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

mpanlFramerNormPrioLinkUtilFromIf 1.1.562.2.4.1.123.3.14.1.3
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

mpanlPrefixDna 1.1.562.2.4.1.123.4
OBJECT IDENTIFIER    

mpanlPrefixDnaRowStatusTable 1.1.562.2.4.1.123.4.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlPrefixDna components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlPrefixDnaRowStatusEntry

mpanlPrefixDnaRowStatusEntry 1.1.562.2.4.1.123.4.1.1
A single entry in the table represents a single mpanlPrefixDna component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlPrefixDnaRowStatusEntry  

mpanlPrefixDnaRowStatus 1.1.562.2.4.1.123.4.1.1.1
This variable is used as the basis for SNMP naming of mpanlPrefixDna components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlPrefixDnaComponentName 1.1.562.2.4.1.123.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlPrefixDnaStorageType 1.1.562.2.4.1.123.4.1.1.4
This variable represents the storage type value for the mpanlPrefixDna tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlPrefixDnaNumberingPlanIndicatorIndex 1.1.562.2.4.1.123.4.1.1.10
This variable represents an index for the mpanlPrefixDna tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlPrefixDnaDataNetworkAddressIndex 1.1.562.2.4.1.123.4.1.1.11
This variable represents an index for the mpanlPrefixDna tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DigitString Size(1..15)  

mpanlDlci 1.1.562.2.4.1.123.5
OBJECT IDENTIFIER    

mpanlDlciRowStatusTable 1.1.562.2.4.1.123.5.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlDlci components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciRowStatusEntry

mpanlDlciRowStatusEntry 1.1.562.2.4.1.123.5.1.1
A single entry in the table represents a single mpanlDlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciRowStatusEntry  

mpanlDlciRowStatus 1.1.562.2.4.1.123.5.1.1.1
This variable is used as the basis for SNMP naming of mpanlDlci components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDlciComponentName 1.1.562.2.4.1.123.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDlciStorageType 1.1.562.2.4.1.123.5.1.1.4
This variable represents the storage type value for the mpanlDlci tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDlciIndex 1.1.562.2.4.1.123.5.1.1.10
This variable represents the index for the mpanlDlci tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 17..1007  

mpanlDlciStateTable 1.1.562.2.4.1.123.5.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciStateEntry

mpanlDlciStateEntry 1.1.562.2.4.1.123.5.10.1
An entry in the mpanlDlciStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciStateEntry  

mpanlDlciAdminState 1.1.562.2.4.1.123.5.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mpanlDlciOperationalState 1.1.562.2.4.1.123.5.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlDlciUsageState 1.1.562.2.4.1.123.5.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mpanlDlciAvailabilityStatus 1.1.562.2.4.1.123.5.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mpanlDlciProceduralStatus 1.1.562.2.4.1.123.5.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlDlciControlStatus 1.1.562.2.4.1.123.5.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlDlciAlarmStatus 1.1.562.2.4.1.123.5.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlDlciStandbyStatus 1.1.562.2.4.1.123.5.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mpanlDlciUnknownStatus 1.1.562.2.4.1.123.5.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mpanlDlciCalldTable 1.1.562.2.4.1.123.5.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group of attributes describes the characteristics of the call such as call type and call state.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciCalldEntry

mpanlDlciCalldEntry 1.1.562.2.4.1.123.5.11.1
An entry in the mpanlDlciCalldTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciCalldEntry  

mpanlDlciQ933CallState 1.1.562.2.4.1.123.5.11.1.2
This attribute indicates the Q.933 state of an SVC call. In the description that follows, 'local' refers to the user who has initiated the SETUP request, and 'remote' refers to the user to whom the local user wishes to connect. State description: In the null state, the network has neither received nor sent call setup requests for this DLCI. In the callInitiated state, the network has received a SETUP message from the local user. In the outgoingCallProceeding state, the network has sent a CALL PROCEEDING message to the local user in response to the SETUP message. In the callPresent state, the network has sent a SETUP message to the remote user. In the incomingCallProceeding state, the network has received a CALL PROCEEDING message from the remote user in response to a SETUP message. In the active state, either the network has sent a CONNECT message to the local user, or the network has received a CONNECT from the remote user. In the disconnectRequest state, the network has received a DISCONNECT message from the local user. In the disconnectIndication state, the network has sent a DISCONNECT to the local user. In the releaseRequest state, the network has sent out a RELEASE message to the local user. The notApplicable state indicates that this attribute is meaningless because the DLCI is a PVC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), outgoingCallProceeding(3), callPresent(6), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20)  

mpanlDlciQ933CallReference 1.1.562.2.4.1.123.5.11.1.3
This attribute indicates the Q.933 call reference number associated with this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..32767  

mpanlDlciSpOpTable 1.1.562.2.4.1.123.5.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the service parameters specific to this instance of Dlci.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciSpOpEntry

mpanlDlciSpOpEntry 1.1.562.2.4.1.123.5.12.1
An entry in the mpanlDlciSpOpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciSpOpEntry  

mpanlDlciMaximumFrameSize 1.1.562.2.4.1.123.5.12.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Frame Relay Vendor Forum Specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4096  

mpanlDlciCommittedBurstSize 1.1.562.2.4.1.123.5.12.1.4
This attribute indicates the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000000  

mpanlDlciExcessBurstSize 1.1.562.2.4.1.123.5.12.1.5
This attribute indicates the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000000  

mpanlDlciAccounting 1.1.562.2.4.1.123.5.12.1.8
This attribute indicates whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be occur, the accountingOn attribute must be on and at least one of the accountCollection options in the DataNetworkAddress component must be selected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mpanlDlciEmissionPriorityToIf 1.1.562.2.4.1.123.5.12.1.9
This attribute indicates the emission priority of frames sent to the interface. A larger value denotes a higher priority.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 1 | 2 | 3  

mpanlDlciTransferPriToNwk 1.1.562.2.4.1.123.5.12.1.10
This attribute indicates the priority at which data is transferred to the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

mpanlDlciTransferPriFromNwk 1.1.562.2.4.1.123.5.12.1.11
This attribute indicates the priority at which data is transferred from the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

mpanlDlciStatsTable 1.1.562.2.4.1.123.5.13
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational statistics for the MPANL Data Link Connection Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciStatsEntry

mpanlDlciStatsEntry 1.1.562.2.4.1.123.5.13.1
An entry in the mpanlDlciStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciStatsEntry  

mpanlDlciFrmToIf 1.1.562.2.4.1.123.5.13.1.1
This attribute counts the frames sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciFecnFrmToIf 1.1.562.2.4.1.123.5.13.1.2
This attribute counts the frames sent to the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBecnFrmToIf 1.1.562.2.4.1.123.5.13.1.3
This attribute counts the frames sent to the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBciToSubnet 1.1.562.2.4.1.123.5.13.1.4
This attribute counts the frames sent into the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDeFrmToIf 1.1.562.2.4.1.123.5.13.1.5
This attribute counts the frames sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscCongestedToIf 1.1.562.2.4.1.123.5.13.1.6
This attribute counts the number of frame discards at the MPANL service due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscDeCongestedToIf 1.1.562.2.4.1.123.5.13.1.7
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the MPANL service, due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciFrmFromIf 1.1.562.2.4.1.123.5.13.1.8
This attribute counts the frames received from the interface. Frames that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciFecnFrmFromIf 1.1.562.2.4.1.123.5.13.1.9
This attribute counts the frames received from the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBecnFrmFromIf 1.1.562.2.4.1.123.5.13.1.10
This attribute counts the frames received from the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciFciFromSubnet 1.1.562.2.4.1.123.5.13.1.11
This attribute counts the frames received from the network with the Forward Congestion Indication (FCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBciFromSubnet 1.1.562.2.4.1.123.5.13.1.12
This attribute counts the frames received from the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDeFrmFromIf 1.1.562.2.4.1.123.5.13.1.13
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciExcessFrmFromIf 1.1.562.2.4.1.123.5.13.1.14
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscExcessFromIf 1.1.562.2.4.1.123.5.13.1.15
This attribute counts the frames which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscFrameAbit 1.1.562.2.4.1.123.5.13.1.16
This attribute counts the number of frame discards at the MPANL Service, due to an inactive PVC status, in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscCongestedFromIf 1.1.562.2.4.1.123.5.13.1.17
This attribute counts the number of frame discards at the MPANL service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscDeCongestedFromIf 1.1.562.2.4.1.123.5.13.1.18
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the MPANL service, due to local congestion, in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciErrorShortFrmFromIf 1.1.562.2.4.1.123.5.13.1.19
This attribute counts the frames received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciErrorLongFrmFromIf 1.1.562.2.4.1.123.5.13.1.20
This attribute counts the frames received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Frames whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBecnFrmSetByService 1.1.562.2.4.1.123.5.13.1.21
This attribute counts the number of frames with BECN set by the MPANL service. It is incremented whenever the MPANL service sets BECN on a frame upon detecting local congestion. This count is incremented regardless of whether the frame already bears a set BECN bit since its use is to determine the place of congestion. When the count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBytesToIf 1.1.562.2.4.1.123.5.13.1.22
This attribute counts the bytes sent out the interface. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDeBytesToIf 1.1.562.2.4.1.123.5.13.1.23
This attribute counts the bytes sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscCongestedToIfBytes 1.1.562.2.4.1.123.5.13.1.24
This attribute counts the number of byte discards at the MPANL service due to local congestion in the direction toward the link. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscDeCongestedToIfBytes 1.1.562.2.4.1.123.5.13.1.25
This attribute counts the number of discard eligible (DE=1) byte discards at the MPANL service due to local congestion in the direction toward the link. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciBytesFromIf 1.1.562.2.4.1.123.5.13.1.26
This attribute counts the bytes received from the interface. Bytes that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDeBytesFromIf 1.1.562.2.4.1.123.5.13.1.27
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciExcessBytesFromIf 1.1.562.2.4.1.123.5.13.1.28
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscExcessFromIfBytes 1.1.562.2.4.1.123.5.13.1.29
This attribute counts the bytes which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscByteAbit 1.1.562.2.4.1.123.5.13.1.30
This attribute counts the bytes which were discarded due to aBit turned off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscCongestedFromIfBytes 1.1.562.2.4.1.123.5.13.1.31
This attribute counts the number of byte discards at the MPANL service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscDeCongestedFromIfBytes 1.1.562.2.4.1.123.5.13.1.32
This attribute counts the number of discard eligible (DE=1) byte discards at the MPANL service due to local congestion in the direction toward the network. When the maximum count is reached the count wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciErrorLongBytesFromIf 1.1.562.2.4.1.123.5.13.1.34
This attribute counts the bytes received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Bytes whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciTransferPriorityToNetwork 1.1.562.2.4.1.123.5.13.1.37
This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

mpanlDlciTransferPriorityFromNetwork 1.1.562.2.4.1.123.5.13.1.38
This attribute is obsolete. It is replaced by attribute transferPriorityFromNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

mpanlDlciIntTable 1.1.562.2.4.1.123.5.14
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational statistics for the MPANL Data Link Connection Identifier interval data.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciIntEntry

mpanlDlciIntEntry 1.1.562.2.4.1.123.5.14.1
An entry in the mpanlDlciIntTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciIntEntry  

mpanlDlciStartTime 1.1.562.2.4.1.123.5.14.1.1
This attribute indicates the start time of this interval period. If the Vc spans 12 hour time or time of day change, startTime reflects new time as recorded at 12 hour periods or time of day changes. A new interval period is started each time an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

mpanlDlciTotalIngressBytes 1.1.562.2.4.1.123.5.14.1.2
This attribute counts the total bytes received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

mpanlDlciTotalEgressBytes 1.1.562.2.4.1.123.5.14.1.3
This attribute counts the total bytes sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

mpanlDlciEirIngressBytes 1.1.562.2.4.1.123.5.14.1.4
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

mpanlDlciEirEgressBytes 1.1.562.2.4.1.123.5.14.1.5
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

mpanlDlciDiscardedBytes 1.1.562.2.4.1.123.5.14.1.6
This attribute counts the total bytes in invalid frames received from the interface and discarded at the DLCI since the start of the interval period. This count is a sum of octets in frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned64 Size(8)  

mpanlDlciTotalIngressSegFrm 1.1.562.2.4.1.123.5.14.1.7
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames received from the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciTotalEgressSegFrm 1.1.562.2.4.1.123.5.14.1.8
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciEirIngressSegFrm 1.1.562.2.4.1.123.5.14.1.9
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciEirEgressSegFrm 1.1.562.2.4.1.123.5.14.1.10
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciDiscardedSegFrm 1.1.562.2.4.1.123.5.14.1.11
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in invalid frames received from the interface and discarded at the DLCI. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of invalid frames received from the interface and discarded at the DLCI. Segments of frames are counted since the start of the interval period. The count is reset to zero when an accounting record is generated. The count is a sum of segments in frames or frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciCallReferenceNumber 1.1.562.2.4.1.123.5.14.1.17
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciElapsedDifference 1.1.562.2.4.1.123.5.14.1.18
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since the call started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciAbitTable 1.1.562.2.4.1.123.5.15
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the A-Bit status information for this Data Link Connection Identifier. A-Bit status information is only applicable for SPVCs. For SVCs, the values of attributes under this group are all notApplicable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciAbitEntry

mpanlDlciAbitEntry 1.1.562.2.4.1.123.5.15.1
An entry in the mpanlDlciAbitTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciAbitEntry  

mpanlDlciABitStatusToIf 1.1.562.2.4.1.123.5.15.1.1
This attribute is the most recent A-Bit status sent to the interface. The A-Bit status is originated from the SPVC end point at the remote end of the Passport subnet and it is relayed to the interface by Mpanl. When an inactive setting is sent out, Mpanl will discard any data offered from the interface. When an active setting is sent out, Mpanl will try to relay all data offered from the interface to the other end of the SPVC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

mpanlDlciABitReasonToIf 1.1.562.2.4.1.123.5.15.1.2
This attribute provides the reason (if any) for an inactive status to be sent to the interface. This reason is not applicable for an active status. A-Bit status reason description: The A-Bit status reason is notApplicable when the A-Bit status is active. The A-Bit status reason is remoteUserSignaled if the SPVC end point originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The SPVC end point must be running network site LMI protocol for this A-Bit status reason to be sent. The A-Bit status reason is remoteLmiError if the LMI protocol is down at the SPVC end point originating this A-Bit status reason. The A-Bit status reason is remoteLinkDown if the physical interface is disabled at the SPVC end point originating this A-Bit status reason. The A-Bit reason is vcDown if no A-Bit status has been sent to the interface (i.e., no A-Bit status has been relayed).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), remoteLmiError(3), remoteLinkDown(5), vcDown(6)  

mpanlDlciABitStatusFromIf 1.1.562.2.4.1.123.5.15.1.3
This attribute is the most recent A-Bit status received from the interface. It is an indication from the equipment attached to the interface on whether it is ready to accept data. Mpanl relays the A- Bit status from interface to the other end of the SPVC. When an inactive setting is received, Mpanl will discard any data offered from the subnet. When an active setting is received, Mpanl will try to relay all data offered from the subnet to the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

mpanlDlciABitReasonFromIf 1.1.562.2.4.1.123.5.15.1.4
This attribute provides the reason (if any) for an inactive status to be sent to the subnet. This reason is not applicable for an active status. A-Bit status reason description: The A-Bit status reason is notApplicable when the A-Bit status is active. The A-Bit status reason is remoteUserSignaled if the SPVC end point originating the A-Bit status has detected that the DLCI is inactive at the remote network through the LMI protocol. The SPVC end point must be running network site LMI protocol for this A-Bit status reason to be sent. The A-Bit status reason is remoteLmiError if the LMI protocol is down at the SPVC end point originating this A-Bit status reason. The A-Bit status reason is remoteLinkDown if the physical interface is disabled at the SPVC end point originating this A-Bit status reason. The A-Bit reason is vcDown if no A-Bit status has been received from the interface (i.e., no A-Bit status has been relayed).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), remoteLmiError(3), remoteLinkDown(5), vcDown(6)  

mpanlDlciLoopbackState 1.1.562.2.4.1.123.5.15.1.5
This attribute has the value on when the DLCI is in loopback mode and off otherwise. This loopback command verbs start and stop are used to initiate and terminate the loopback mode for a DLCI. While loopbackState is on, an active A-bit signal will be reliably propagated across the subnet to the remote DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mpanlDlciLb 1.1.562.2.4.1.123.5.2
OBJECT IDENTIFIER    

mpanlDlciLbRowStatusTable 1.1.562.2.4.1.123.5.2.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlDlciLb components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLbRowStatusEntry

mpanlDlciLbRowStatusEntry 1.1.562.2.4.1.123.5.2.1.1
A single entry in the table represents a single mpanlDlciLb component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLbRowStatusEntry  

mpanlDlciLbRowStatus 1.1.562.2.4.1.123.5.2.1.1.1
This variable is used as the basis for SNMP naming of mpanlDlciLb components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDlciLbComponentName 1.1.562.2.4.1.123.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDlciLbStorageType 1.1.562.2.4.1.123.5.2.1.1.4
This variable represents the storage type value for the mpanlDlciLb tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDlciLbIndex 1.1.562.2.4.1.123.5.2.1.1.10
This variable represents the index for the mpanlDlciLb tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlDlciLbStatsTable 1.1.562.2.4.1.123.5.2.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains all the statistics for the data loopback tool.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLbStatsEntry

mpanlDlciLbStatsEntry 1.1.562.2.4.1.123.5.2.10.1
An entry in the mpanlDlciLbStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLbStatsEntry  

mpanlDlciLbLocalTotalFrm 1.1.562.2.4.1.123.5.2.10.1.1
This attribute records the number of frames looped back to the link since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbLocalTotalBytes 1.1.562.2.4.1.123.5.2.10.1.2
This attribute records the number of bytes looped back to the link since loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbLocalFecnFrm 1.1.562.2.4.1.123.5.2.10.1.3
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbLocalBecnFrm 1.1.562.2.4.1.123.5.2.10.1.4
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbLocalDeFrm 1.1.562.2.4.1.123.5.2.10.1.5
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbLocalDeBytes 1.1.562.2.4.1.123.5.2.10.1.6
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteTotalFrm 1.1.562.2.4.1.123.5.2.10.1.7
This attribute records the number of frames looped back to the subnet since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteTotalBytes 1.1.562.2.4.1.123.5.2.10.1.8
This attribute records the number of bytes looped back to the subnet since loopback was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteFecnFrm 1.1.562.2.4.1.123.5.2.10.1.9
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteBecnFrm 1.1.562.2.4.1.123.5.2.10.1.10
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteDeFrm 1.1.562.2.4.1.123.5.2.10.1.13
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciLbRemoteDeBytes 1.1.562.2.4.1.123.5.2.10.1.14
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciVc 1.1.562.2.4.1.123.5.3
OBJECT IDENTIFIER    

mpanlDlciVcRowStatusTable 1.1.562.2.4.1.123.5.3.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlDlciVc components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciVcRowStatusEntry

mpanlDlciVcRowStatusEntry 1.1.562.2.4.1.123.5.3.1.1
A single entry in the table represents a single mpanlDlciVc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciVcRowStatusEntry  

mpanlDlciVcRowStatus 1.1.562.2.4.1.123.5.3.1.1.1
This variable is used as the basis for SNMP naming of mpanlDlciVc components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDlciVcComponentName 1.1.562.2.4.1.123.5.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDlciVcStorageType 1.1.562.2.4.1.123.5.3.1.1.4
This variable represents the storage type value for the mpanlDlciVc tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDlciVcIndex 1.1.562.2.4.1.123.5.3.1.1.10
This variable represents the index for the mpanlDlciVc tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlDlciVcCadTable 1.1.562.2.4.1.123.5.3.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciVcCadEntry

mpanlDlciVcCadEntry 1.1.562.2.4.1.123.5.3.10.1
An entry in the mpanlDlciVcCadTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciVcCadEntry  

mpanlDlciVcType 1.1.562.2.4.1.123.5.3.10.1.1
This attribute displays the type of call, pvc,svc or spvc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER svc(0), pvc(1), spvc(2)  

mpanlDlciVcState 1.1.562.2.4.1.123.5.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

mpanlDlciVcPreviousState 1.1.562.2.4.1.123.5.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

mpanlDlciVcDiagnosticCode 1.1.562.2.4.1.123.5.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDlciVcPreviousDiagnosticCode 1.1.562.2.4.1.123.5.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDlciVcCalledNpi 1.1.562.2.4.1.123.5.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciVcCalledDna 1.1.562.2.4.1.123.5.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

mpanlDlciVcCalledLcn 1.1.562.2.4.1.123.5.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

mpanlDlciVcCallingNpi 1.1.562.2.4.1.123.5.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciVcCallingDna 1.1.562.2.4.1.123.5.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

mpanlDlciVcCallingLcn 1.1.562.2.4.1.123.5.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

mpanlDlciVcAccountingEnabled 1.1.562.2.4.1.123.5.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

mpanlDlciVcFastSelectCall 1.1.562.2.4.1.123.5.3.10.1.13
This attribute displays that this is a fast select call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mpanlDlciVcPathReliability 1.1.562.2.4.1.123.5.3.10.1.19
This attribute displays the path reliability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

mpanlDlciVcAccountingEnd 1.1.562.2.4.1.123.5.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER callingEnd(0), calledEnd(1)  

mpanlDlciVcPriority 1.1.562.2.4.1.123.5.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

mpanlDlciVcSegmentSize 1.1.562.2.4.1.123.5.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4096  

mpanlDlciVcMaxSubnetPktSize 1.1.562.2.4.1.123.5.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4096  

mpanlDlciVcRcosToNetwork 1.1.562.2.4.1.123.5.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

mpanlDlciVcRcosFromNetwork 1.1.562.2.4.1.123.5.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

mpanlDlciVcEmissionPriorityToNetwork 1.1.562.2.4.1.123.5.3.10.1.30
This attribute displays the network internal emission priotity to the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

mpanlDlciVcEmissionPriorityFromNetwork 1.1.562.2.4.1.123.5.3.10.1.31
This attribute displays the network internal emission priotity from the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

mpanlDlciVcDataPath 1.1.562.2.4.1.123.5.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..32)  

mpanlDlciVcIntdTable 1.1.562.2.4.1.123.5.3.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciVcIntdEntry

mpanlDlciVcIntdEntry 1.1.562.2.4.1.123.5.3.11.1
An entry in the mpanlDlciVcIntdTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciVcIntdEntry  

mpanlDlciVcCallReferenceNumber 1.1.562.2.4.1.123.5.3.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Hex 0..16777215  

mpanlDlciVcElapsedTimeTillNow 1.1.562.2.4.1.123.5.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

mpanlDlciVcSegmentsRx 1.1.562.2.4.1.123.5.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

mpanlDlciVcSegmentsSent 1.1.562.2.4.1.123.5.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

mpanlDlciVcStartTime 1.1.562.2.4.1.123.5.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

mpanlDlciVcFrdTable 1.1.562.2.4.1.123.5.3.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciVcFrdEntry

mpanlDlciVcFrdEntry 1.1.562.2.4.1.123.5.3.12.1
An entry in the mpanlDlciVcFrdTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciVcFrdEntry  

mpanlDlciVcFrmCongestedToSubnet 1.1.562.2.4.1.123.5.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcCannotForwardToSubnet 1.1.562.2.4.1.123.5.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcNotDataXferToSubnet 1.1.562.2.4.1.123.5.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcOutOfRangeFrmFromSubnet 1.1.562.2.4.1.123.5.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcCombErrorsFromSubnet 1.1.562.2.4.1.123.5.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcDuplicatesFromSubnet 1.1.562.2.4.1.123.5.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcNotDataXferFromSubnet 1.1.562.2.4.1.123.5.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcFrmLossTimeouts 1.1.562.2.4.1.123.5.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcOoSeqByteCntExceeded 1.1.562.2.4.1.123.5.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcPeakOoSeqPktCount 1.1.562.2.4.1.123.5.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcPeakOoSeqFrmForwarded 1.1.562.2.4.1.123.5.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcSendSequenceNumber 1.1.562.2.4.1.123.5.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcPktRetryTimeouts 1.1.562.2.4.1.123.5.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcPeakRetryQueueSize 1.1.562.2.4.1.123.5.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcSubnetRecoveries 1.1.562.2.4.1.123.5.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

mpanlDlciVcOoSeqPktCntExceeded 1.1.562.2.4.1.123.5.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDlciVcPeakOoSeqByteCount 1.1.562.2.4.1.123.5.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..50000  

mpanlDlciVcDmepTable 1.1.562.2.4.1.123.5.3.417
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciVcDmepEntry

mpanlDlciVcDmepEntry 1.1.562.2.4.1.123.5.3.417.1
An entry in the mpanlDlciVcDmepTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciVcDmepEntry  

mpanlDlciVcDmepValue 1.1.562.2.4.1.123.5.3.417.1.1
This variable represents both the value and the index for the mpanlDlciVcDmepTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowPointer  

mpanlDlciLCo 1.1.562.2.4.1.123.5.4
OBJECT IDENTIFIER    

mpanlDlciLCoRowStatusTable 1.1.562.2.4.1.123.5.4.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlDlciLCo components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLCoRowStatusEntry

mpanlDlciLCoRowStatusEntry 1.1.562.2.4.1.123.5.4.1.1
A single entry in the table represents a single mpanlDlciLCo component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLCoRowStatusEntry  

mpanlDlciLCoRowStatus 1.1.562.2.4.1.123.5.4.1.1.1
This variable is used as the basis for SNMP naming of mpanlDlciLCo components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDlciLCoComponentName 1.1.562.2.4.1.123.5.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDlciLCoStorageType 1.1.562.2.4.1.123.5.4.1.1.4
This variable represents the storage type value for the mpanlDlciLCo tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDlciLCoIndex 1.1.562.2.4.1.123.5.4.1.1.10
This variable represents the index for the mpanlDlciLCo tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlDlciLCoPathDataTable 1.1.562.2.4.1.123.5.4.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains all operational attributes for the path oriented LCo.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLCoPathDataEntry

mpanlDlciLCoPathDataEntry 1.1.562.2.4.1.123.5.4.10.1
An entry in the mpanlDlciLCoPathDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLCoPathDataEntry  

mpanlDlciLCoState 1.1.562.2.4.1.123.5.4.10.1.1
This attribute reflects the current state of the connection. The pathDown state indicates that the application has not yet signalled for a path. The selectingRoute state occurs when a request has been sent to the route selector and it has not yet responded. The connectingState occurs while a path is being established. The pathUp state is the normal operational state of a path. The pathDownRetrying state indicates a path that attempted route selection but received no route and is now waiting to retry route selection again.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pathDown(0), selectingRoute(1), connecting(2), pathUp(3), pathDownRetrying(4)  

mpanlDlciLCoEnd 1.1.562.2.4.1.123.5.4.10.1.3
This attribute identifies whether this is the calling or called end of the path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER calling(0), called(1)  

mpanlDlciLCoCostMetric 1.1.562.2.4.1.123.5.4.10.1.4
This attribute gives the route's total cost metric. It is calculated as the sum of the cost metric of all trunks in the path at the time the connection was established. The cost metric of a trunk is defined by the trunkCost attribute of the Trunk component. The costMetric for an LCo that is originated and terminated on the same module is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

mpanlDlciLCoDelayMetric 1.1.562.2.4.1.123.5.4.10.1.5
This attribute gives the total delay of the route as the one way delay for a 512 byte packet. It is calculated as the sum of the delays of all trunks in the path stored in topology at the time the connection was established. The delay for an LCo that is originated and terminated on the same module is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

mpanlDlciLCoRoundTripDelay 1.1.562.2.4.1.123.5.4.10.1.6
This attribute contains the time taken for a packet (cell) of 44 bytes to be transmitted to the remote LCo and return to this LCo. The number reported is given in milliseconds to the nearest millisecond. A value of one millisecond is reported if the time is less than 1 millisecond even though the delay may be less than 1 millisecond when the LCo is originated and terminated on the same module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..200000  

mpanlDlciLCoSetupPriority 1.1.562.2.4.1.123.5.4.10.1.7
This attribute gives the priority at which the current path is established. Zero is the highest priority and four is the lowest. The holdingPriority, a complementary attribute of this component, indicates the priority a path maintains once it is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4  

mpanlDlciLCoHoldingPriority 1.1.562.2.4.1.123.5.4.10.1.8
This attribute gives the priority at which a path holds its current path once the path is established. Zero is the highest priority and four is the lowest. The setupPriority, a complementary attribute, indicates the priority of a path at establishment time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4  

mpanlDlciLCoRequiredTxBandwidth 1.1.562.2.4.1.123.5.4.10.1.9
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of the trunks of its route. This attribute represents the bandwidth for traffic outgoing to the remote end point. The originating end of the connection determines this value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..2048000  

mpanlDlciLCoRequiredRxBandwidth 1.1.562.2.4.1.123.5.4.10.1.10
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of trunks of its route. This attribute represents the bandwidth for traffic incoming from the remote end point. The originating end of the connection determines this value
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..2048000  

mpanlDlciLCoRequiredTrafficType 1.1.562.2.4.1.123.5.4.10.1.11
This operational attribute indicates the type of traffic transmitted over the path. There are eight possible traffic types, and the path can transmit only one of them. The originating end of the connection determines the type. These are arbitrary designations for traffic type. The voice, data and video traffic types are defined, and five other arbitrary traffic types can be defined by the network administration. This attribute is used in the route selection process to restrict the route to trunks that support this traffic type. The supportedTrafficType trunk attribute lists all the types of traffic allowed on the trunk. For example, if requiredTrafficType is specified as trafficType1 then only trunks that include trafficType1 in supportedTrafficType, will be candidates for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER voice(0), data(1), video(2), trafficType1(3), trafficType2(4), trafficType3(5), trafficType4(6), trafficType5(7)  

mpanlDlciLCoPermittedTrunkTypes 1.1.562.2.4.1.123.5.4.10.1.12
This operational attribute lists up to eight types of trunk that can be used on the route. The originating end of the connection determines the types. The terrestrial and satellite trunk types have been defined, leaving six remaining arbitrary types that can be defined by the network administration. The trunk's type is indicated in the trunkType attribute of the Trunk component. When selecting a route, PORS only chooses trunks whose trunkType are in the permittedTrunkTypes for the path. Description of bits: terrestrial(0) satellite(1) trunkType1(2) trunkType2(3) trunkType3(4) trunkType4(5) trunkType5(6) trunkType6(7)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mpanlDlciLCoRequiredSecurity 1.1.562.2.4.1.123.5.4.10.1.13
This attribute indicates the required minimum level of security of the trunks on the route. Zero represents the most secure and seven represents the least secure. The trunk's security is indicated by the trunkSecurity attribute of the Trunk component, and has values identical in range and meaning to the requiredSecurity attribute. PORS ensures that any route selected does not contain a trunk whose trunkSecurity attribute is numerically greater than the requiredSecurity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

mpanlDlciLCoRequiredCustomerParameter 1.1.562.2.4.1.123.5.4.10.1.14
This attribute indicates the allowed customer defined parameter of the trunks on the route.The originating end of the connection determines the customer defined parameter. Its value, a number from zero to seven, is chosen by a network administration to have a meaning specific to their network, thus allowing them to customize the use of their trunks. A complementary trunk attribute, customerParameter, also has a value from zero to seven. The route selection process does not consider trunks whose customerParameter is greater than the requiredCustomerParameter of the path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

mpanlDlciLCoEmissionPriority 1.1.562.2.4.1.123.5.4.10.1.15
This attribute indicates the urgency with which packets on the path are emitted by the trunks on the route. The originating end of the connection selects the emissionPriority. EmissionPriority of zero indicates the highest emission priority, while two indicates the lowest emission priority. Packets with a higher emissionPriority (or numerically less) are serviced and sent out before the packets of lower emissionPriority (or numerically higher).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2  

mpanlDlciLCoDiscardPriority 1.1.562.2.4.1.123.5.4.10.1.16
This attribute indicates the importance of the packets on the path.The originating end of the connection sets discardPriority. One is used for paths carrying the most important traffic, and three is used for paths carrying the least important traffic. Packets with lower discardPriority(numerically lower) are discarded after packets with a higher discardPriority(numerically higher).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..3  

mpanlDlciLCoRetryCount 1.1.562.2.4.1.123.5.4.10.1.18
This attribute is the count of the number of times the path chosen during route selection could not be instantiated. This count should be three or below if the network is performing adequately. A high value indicates that the route selection is often performed using an out-of-date view of available network bandwidth and/or topology. This attribute will only increase at the calling end of the connection. This attribute is reset each time a path reconnects and stops counting when it reaches its maximum value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlDlciLCoPathFailureCount 1.1.562.2.4.1.123.5.4.10.1.19
This attribute is the count of the number of times the path has successfully reconnected. It is set to zero the first time the path is up. If a path fails anytime after connecting, this count will be incremented when the path is up again. Failed route requests do not count in this statistic. See retryCount(rcount) - page 78. This attribute stops counting at its maximum value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

mpanlDlciLCoReasonForNoRoute 1.1.562.2.4.1.123.5.4.10.1.20
This attribute is the route selection's reasonForNoRoute and provides a brief reason for which a route was not selected. The reasons are essentially self-explanatory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), destinationNameTooLong(1), destinationNotSpecified(2), unknownDestinationName(3), incorrectDestination(4), incorrectDestinationEndPoint(5), unknownSource(6), unknownDestination(7), sameNode(8), routeCostTooMuch(9), routesDelayTooLong(10), attributesNotMet(11), anError(12), attributeProfileProblem(13), manualPathIndexProblem(14)  

mpanlDlciLCoLastTearDownReason 1.1.562.2.4.1.123.5.4.10.1.21
This attribute reflects the last tear down reason for a connection (LCo). In many cases this displays the reason for a momentary service interruption. This attribute applies to the last path failure only. If a path is no longer up, this may indicate why the path has failed. In many cases an alarm will also be generated with more specific information. The following is a brief description of the reasons: none - This path has no information for the teardown. normalShutDown - This path has gone down due to normal call termination. insufficientTxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the transmit direction. insufficientRxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the receive direction. trunkFailure- A trunk on the path has failed or has gone down due to a provisioning change of a critical attribute. trunkCardFailure- A trunk FP card has failed along the path. accessCardFailure- The FP on which the peer access service was running has failed. operatorForced- The path has terminated due to the operator locking a trunk along the path. lostLcnClash- The path has terminated because the PAs at both ends of an intermediate trunk have allocated the same LC to different calls. When this happens both calls must go down and then try to come up again a fraction of a second later (effectively ensuring that they will now be assigned different LCs). It is normal to get the odd clash especially when the PA's usedLC is approaching the PA's maxLC. networkCongestion - The path has failed due to control information being lost and not recoverable. trunkNotFound - Occurs on a manual path usually. Check for trunks not up or names provisioned incorrectly. farEndNotFound - The far end is not provisioned or is not up. Check remote Name. wrongModuleReached - This may occur on a manual path. Check provisioning for correct trunk and service names. For a normal path, the network Topology may be changing. Check remote provisioned DNA. farEndBusy - The far end has been reached but it is busy. Check remote provisioned DNA and remote end provisioning. unknownReason - The failure was not resolved. farEndNotReady - The remote end was reached but the connection was refused due to the remote end not being enabled. serviceTypeMismatch - The remote service type does not match this service type. Check provisioning. reconnectFromFarEnd - The remote end re-established this connection. Check the remote end lastTearDownReason to determine the real reason. bumped - Another call bumped this path from a trunk to get bandwidth (or an LC) which it required to come up. This other path had a higher setupPriority than this path's holdingPriority, hence it was allowed to steal the bandwidth (or LC) from this path. optimized - This call has been rerouted due to the optimization feature. The call is still active; this just indicates why the path changed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), normalShutDown(1), insufficientTxLcOrBandwidth(2), insufficientRxLcOrBandwidth(3), trunkFailure(4), trunkCardFailure(5), operatorForced(6), lostLcnClash(7), networkCongestion(8), trunkNotFound(9), farEndNotFound(10), wrongModuleReached(11), farEndBusy(12), callLoopedBack(13), unknownReason(14), farEndNotReady(15), remoteNameMismatch(16), serviceTypeMismatch(17), reconnectFromFarEnd(18), bumped(19), accessCardFailure(20), optimized(21), overrideRemoteName(22)  

mpanlDlciLCoPathFailureAction 1.1.562.2.4.1.123.5.4.10.1.22
This attribute displays whether the application is set to tolerate a momentary interruption of a path while a new path is selected. If disconnectConnection is displayed, the application is informed as soon as possible about a failure by disconnection. If the attribute displays reRoutePath, the path may attempt an immediate reroute, provided the failure is a recoverable failure. If rerouting fails the application is informed of the failure. With this option set to reRoutePath the LCo may wait up to 30 seconds before informing the service of complete disconnection in order to allow both ends to attempt to reconnect. All pathTypes respect this attribute. Also, on a manualPath with both ends provisioned with independent paths (at least with respect to the failure) this option will have the desired effect that the path is rerouted without complete disconnection at both ends.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnectConnection(0), reRoutePath(1)  

mpanlDlciLCoBumpPreference 1.1.562.2.4.1.123.5.4.10.1.23
This attribute specifies when bumping will occur during the route selection process. Bumping may occur when necessary or always. It will be necessary for a connection to bump if there is not enough resources for the connection to be established and these resources are occupied by a connection whose holdingPriority is lower (numerically higher) than the connection's setupPriority. A connection may also always bump in order to obtain the best route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bumpWhenNecessary(0), bumpToObtainBestRoute(1)  

mpanlDlciLCoOptimization 1.1.562.2.4.1.123.5.4.10.1.24
This attribute is used to specify whether this connection should attempt to optimize its path when requested by the routing PORS component. Every path is as optimal as it can be when it is established, but as network traffic patterns and configurations change this path may no longer be as optimal as it could be. The PORS connection manager on a module requests circuits to optimize at the optimization interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlDlciLCoPathUpDateTime 1.1.562.2.4.1.123.5.4.10.1.25
This is the time stamp when the current path was established or reestablished.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|19)  

mpanlDlciLCoStatsTable 1.1.562.2.4.1.123.5.4.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational statistics attributes for the path oriented LCo.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLCoStatsEntry

mpanlDlciLCoStatsEntry 1.1.562.2.4.1.123.5.4.11.1
An entry in the mpanlDlciLCoStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLCoStatsEntry  

mpanlDlciLCoPktsToNetwork 1.1.562.2.4.1.123.5.4.11.1.1
This attribute counts the number of packets transmitted to the network over this Logical Connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mpanlDlciLCoBytesToNetwork 1.1.562.2.4.1.123.5.4.11.1.2
This attribute counts the number of bytes sent to the network over this Logical Connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mpanlDlciLCoPktsFromNetwork 1.1.562.2.4.1.123.5.4.11.1.3
This attribute counts the number of packets received from the remote LCo via the network. This attribute wraps to 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mpanlDlciLCoBytesFromNetwork 1.1.562.2.4.1.123.5.4.11.1.4
This attribute counts the number of bytes received from the remote LCo via the network. This attribute wraps to 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mpanlDlciLCoCallDataTable 1.1.562.2.4.1.123.5.4.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains all operational attributes for the path oriented LCo.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLCoCallDataEntry

mpanlDlciLCoCallDataEntry 1.1.562.2.4.1.123.5.4.12.1
An entry in the mpanlDlciLCoCallDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLCoCallDataEntry  

mpanlDlciLCoCallingNpi 1.1.562.2.4.1.123.5.4.12.1.27
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciLCoCallingDna 1.1.562.2.4.1.123.5.4.12.1.28
This attribute displays the Data Network Address (DNA) of the calling end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mpanlDlciLCoElapsedTimeTillNow 1.1.562.2.4.1.123.5.4.12.1.30
This attribute displays the total duration in tenths of miliseconds that a connection has been up for a call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16777215  

mpanlDlciLCoCallReferenceNumber 1.1.562.2.4.1.123.5.4.12.1.31
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Hex 0..16777215  

mpanlDlciLCoCalledNpi 1.1.562.2.4.1.123.5.4.12.1.33
This attribute indicates the Numbering Plan Indicator (NPI) of the called end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciLCoCalledDna 1.1.562.2.4.1.123.5.4.12.1.34
This attribute indicates the Data Network Address (DNA) of the called (destination) DTE to which this call is sent. This address if defined at the receiving end will complete the logical connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mpanlDlciLCoPathTable 1.1.562.2.4.1.123.5.4.401
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This attribute contains the trunk component names over which the path has been instantiated and the remote end point name terminating the path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciLCoPathEntry

mpanlDlciLCoPathEntry 1.1.562.2.4.1.123.5.4.401.1
An entry in the mpanlDlciLCoPathTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciLCoPathEntry  

mpanlDlciLCoPathValue 1.1.562.2.4.1.123.5.4.401.1.1
This variable represents both the value and the index for the mpanlDlciLCoPathTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..40)  

mpanlDlciJvc 1.1.562.2.4.1.123.5.5
OBJECT IDENTIFIER    

mpanlDlciJvcRowStatusTable 1.1.562.2.4.1.123.5.5.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mpanlDlciJvc components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciJvcRowStatusEntry

mpanlDlciJvcRowStatusEntry 1.1.562.2.4.1.123.5.5.1.1
A single entry in the table represents a single mpanlDlciJvc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciJvcRowStatusEntry  

mpanlDlciJvcRowStatus 1.1.562.2.4.1.123.5.5.1.1.1
This variable is used as the basis for SNMP naming of mpanlDlciJvc components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlDlciJvcComponentName 1.1.562.2.4.1.123.5.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlDlciJvcStorageType 1.1.562.2.4.1.123.5.5.1.1.4
This variable represents the storage type value for the mpanlDlciJvc tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlDlciJvcIndex 1.1.562.2.4.1.123.5.5.1.1.10
This variable represents the index for the mpanlDlciJvc tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlDlciJvcOperTable 1.1.562.2.4.1.123.5.5.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes of the Jvc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciJvcOperEntry

mpanlDlciJvcOperEntry 1.1.562.2.4.1.123.5.5.10.1
An entry in the mpanlDlciJvcOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciJvcOperEntry  

mpanlDlciJvcCurrentState 1.1.562.2.4.1.123.5.5.10.1.1
This attribute indicates the current state of the JVC process. The state can be one of: null: waiting for an incoming call or a call request from MPANL, callRequest: waiting for the call connected from MPANL, callIndication: waiting for the call packet from MPANL, callBlockPresent: waiting for the Raccept packet from the subnet, active: relaying packets between the subnet and MPANL, discInitiated: not used by the DCE JVC, discPktPresent: not used by the DCE JVC, callDisconnected: waiting for the termination request from MPANL, callTerminated: waiting for the termination by MPANL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callRequest(1), callIndication(2), callBlockPresent(3), active(4), discInitiated(5), discPktPresent(6), callDisconnected(7), callTerminated(8)  

mpanlDlciJvcPreviousState 1.1.562.2.4.1.123.5.5.10.1.2
This attribute indicates the previous state of the JVC process. The state can be one of: null: waiting for an incoming call or a call request from MPANL, callRequest: waiting for the call connected from MPANL, callIndication: waiting for the call packet from MPANL, callBlockPresent: waiting for the Raccept packet from the subnet, active: relaying packets between the subnet and MPANL, discInitiated: not used by the DCE JVC, discPktPresent: not used by the DCE JVC, callDisconnected: waiting for the termination request from MPANL, callTerminated: waiting for the termination by MPANL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callRequest(1), callIndication(2), callBlockPresent(3), active(4), discInitiated(5), discPktPresent(6), callDisconnected(7), callTerminated(8)  

mpanlDlciJvcCallingNpi 1.1.562.2.4.1.123.5.5.10.1.6
This attribute contains the numbering plan indicator of the calling address. This attribute value is retrieved from the call packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciJvcCallingAddress 1.1.562.2.4.1.123.5.5.10.1.7
This attribute contains the calling DataNetworkAddress of the interface. It includes the DNIC (first 4 digits) for X.121, and the CC (Country Code) for the E.164 address of the calling end. The maximum length of this attribute is 15 digits. This attribute value is retrieved from the call packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

mpanlDlciJvcCallingLcn 1.1.562.2.4.1.123.5.5.10.1.8
This attribute contains the calling LCN (logical channel number) of the interface. This number is assigned to the call request at the calling end. This attribute value is retrieved from the call packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4095  

mpanlDlciJvcCalledNpi 1.1.562.2.4.1.123.5.5.10.1.9
This attribute contains the numbering plan indicator of the called address. This attribute value is retrieved from the call packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mpanlDlciJvcCalledAddress 1.1.562.2.4.1.123.5.5.10.1.10
This attribute contains the called DataNetworkAddress of the interface. It includes the DNIC (first 4 digits) for X.121, and the CC (Country Code) for the E.164 address of the called end. The maximum length of this attribute is 15 digits. This attribute value is retrieved from the Raccept packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(1..15)  

mpanlDlciJvcCalledLcn 1.1.562.2.4.1.123.5.5.10.1.11
This attribute contains the called LCN (logical channel number) of the interface. This number is assigned to the call request at the called end. This attribute value is retrieved from the Raccept packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4095  

mpanlDlciJvcStatTable 1.1.562.2.4.1.123.5.5.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the statistics collected by the Jvc component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlDlciJvcStatEntry

mpanlDlciJvcStatEntry 1.1.562.2.4.1.123.5.5.11.1
An entry in the mpanlDlciJvcStatTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlDlciJvcStatEntry  

mpanlDlciJvcPacketsFromSubnet 1.1.562.2.4.1.123.5.5.11.1.1
This attribute counts all packets including control packets received from the subnet. This number reflects also the packets sent to the MPANL process since the JVC does not drop or generate packets in this direction.The value of this attribute wraps to 0 when the maximum value is reached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciJvcPacketsToSubnet 1.1.562.2.4.1.123.5.5.11.1.2
This attribute counts all packets including control packets sent into the subnet. This number includes Renew Call Timer Packets that are generated by the JVC. The value of this attribute wraps to 0 when the maximum value is reached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciJvcPacketsDiscarded 1.1.562.2.4.1.123.5.5.11.1.3
This attribute counts discarded packets that can not be forwarded into the subnet because of subnet congestion. This attribute is increased when packet forwarding fails to forward a packet into the subnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlDlciJvcProtocolErrors 1.1.562.2.4.1.123.5.5.11.1.4
This attribute counts the number of protocol errors detected by the JVC in both the MPANL and the subnet directions. A protocol error is counted in the following cases: - reception of a packet from MPANL while waiting for a Raccept packet from the subnet, - reception of a packet from the subnet following a call packet and before the callAccepted is received from MPANL, - reception of a packet from the subnet or from MPANL that is shorter than the subnet header. The value of this attribute wraps to 0 when the maximum value is reached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mpanlSig 1.1.562.2.4.1.123.6
OBJECT IDENTIFIER    

mpanlSigRowStatusTable 1.1.562.2.4.1.123.6.1
This entry controls the addition and deletion of mpanlSig components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigRowStatusEntry

mpanlSigRowStatusEntry 1.1.562.2.4.1.123.6.1.1
A single entry in the table represents a single mpanlSig component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigRowStatusEntry  

mpanlSigRowStatus 1.1.562.2.4.1.123.6.1.1.1
This variable is used as the basis for SNMP naming of mpanlSig components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlSigComponentName 1.1.562.2.4.1.123.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlSigStorageType 1.1.562.2.4.1.123.6.1.1.4
This variable represents the storage type value for the mpanlSig tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlSigIndex 1.1.562.2.4.1.123.6.1.1.10
This variable represents the index for the mpanlSig tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlSigSysParmsTable 1.1.562.2.4.1.123.6.13
This group contains the provisionable Q.933 system parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigSysParmsEntry

mpanlSigSysParmsEntry 1.1.562.2.4.1.123.6.13.1
An entry in the mpanlSigSysParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigSysParmsEntry  

mpanlSigCallSetupTimer 1.1.562.2.4.1.123.6.13.1.1
This attribute specifies the time the network will wait for a response to the SETUP message sent to the called user. Upon timer expiry, the SETUP message is retransmitted. The second expiry of this timer causes the call to be cleared. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

mpanlSigDisconnectTimer 1.1.562.2.4.1.123.6.13.1.2
This attribute specifies the time the network will wait for a response to the DISCONNECT message sent to the user. Upon timer expiry, the RELEASE message is sent. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

mpanlSigReleaseTimer 1.1.562.2.4.1.123.6.13.1.3
This attribute specifies the time the network will wait for a response to the RELEASE message sent to the user. Upon timer expiry, the RELEASE message is retransmitted. The second expiry of the timer causes the call to be released. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

mpanlSigCallProceedingTimer 1.1.562.2.4.1.123.6.13.1.4
This attribute specifies the time the network will wait for the CONNECT message from the called user after the network has received the optional CALL PROCEEDING message from the called user. Upon timer expiry, the call is cleared. This value is specified in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

mpanlSigNetworkType 1.1.562.2.4.1.123.6.13.1.5
This attribute specifies whether this Frame Relay service is running on a public or a private network. This value is used solely in populating applicable information elements within those Q.933 messages that require a public or private network indication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER private(1), public(2)  

mpanlSigLapfSysTable 1.1.562.2.4.1.123.6.14
This group contains the provisionable attributes for the SVC data link layer. The data link layer is governed primarily through ITU specification Q.922, and operates over DLCI 0..
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigLapfSysEntry

mpanlSigLapfSysEntry 1.1.562.2.4.1.123.6.14.1
An entry in the mpanlSigLapfSysTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigLapfSysEntry  

mpanlSigWindowSize 1.1.562.2.4.1.123.6.14.1.2
This attribute specifies the window size. This is the maximum number of unacknowledged sequenced frames that may be outstanding from or to this interface at any one time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mpanlSigRetransmitLimit 1.1.562.2.4.1.123.6.14.1.3
This attribute specifies the number of times a frame can be retransmitted by the SVC data link layer before appropriate recovery action is taken.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..20  

mpanlSigAckTimer 1.1.562.2.4.1.123.6.14.1.4
This attribute specifies the period in milliseconds that the network will wait for an acknowledgment to a sent frame. The value set for ackTimer must be less than the value set for idleProbeTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..10000  

mpanlSigAckDelayTimer 1.1.562.2.4.1.123.6.14.1.5
This attribute specifies the maximum period in milliseconds that the network will wait before sending an acknowledgment for a received in-sequence I-frame. A value of 0 means there will be no delay in acknowledgment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

mpanlSigIdleProbeTimer 1.1.562.2.4.1.123.6.14.1.6
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network's side link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65535000  

mpanlSigSvcaccTable 1.1.562.2.4.1.123.6.15
This group contains the provisionable attribute to define the defaultAccounting attribute..
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigSvcaccEntry

mpanlSigSvcaccEntry 1.1.562.2.4.1.123.6.15.1
An entry in the mpanlSigSvcaccTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigSvcaccEntry  

mpanlSigDefaultAccounting 1.1.562.2.4.1.123.6.15.1.1
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the defaultAccounting bit and at least one of the accountCollection bits in the FrsDataNetworkAddress component must be set to on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mpanlSigStateTable 1.1.562.2.4.1.123.6.16
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigStateEntry

mpanlSigStateEntry 1.1.562.2.4.1.123.6.16.1
An entry in the mpanlSigStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigStateEntry  

mpanlSigAdminState 1.1.562.2.4.1.123.6.16.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mpanlSigOperationalState 1.1.562.2.4.1.123.6.16.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlSigUsageState 1.1.562.2.4.1.123.6.16.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mpanlSigStatsTable 1.1.562.2.4.1.123.6.17
This group contains the statistics related to the SVC signaling layer at the interface level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigStatsEntry

mpanlSigStatsEntry 1.1.562.2.4.1.123.6.17.1
An entry in the mpanlSigStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigStatsEntry  

mpanlSigCurrentNumberOfSvcCalls 1.1.562.2.4.1.123.6.17.1.1
This attribute shows the number of Frame Relay SVCs currently existing on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..991  

mpanlSigInCalls 1.1.562.2.4.1.123.6.17.1.4
This attribute indicates the current number of incoming SVCs on this interface (that is, the number of SVCs for which this interface represents the destination end of the call).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigInCallsRefused 1.1.562.2.4.1.123.6.17.1.5
This attribute counts the number of incoming SVC call requests that are rejected by either this interface or by the called user. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigOutCalls 1.1.562.2.4.1.123.6.17.1.6
This attribute shows the current number of outgoing SVCs on this interface (that is, the number of SVCs for which this interface represents the source end of the call).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigOutCallsFailed 1.1.562.2.4.1.123.6.17.1.7
This attribute counts the number of outgoing SVC call requests that are rejected by either this interface, or by the network side of the destination end, or by the called user. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigProtocolErrors 1.1.562.2.4.1.123.6.17.1.8
This attribute counts the number of times a Q.933 protocol error has occurred. Any one of the following events constitutes a protocol error: 1. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir, Bc and Be are all zero; 2. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir is zero but Bc is non-zero, or Bc is zero but Cir is non-zero; 3. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, the minimum acceptable Cir is greater than Cir; 4. At the destination end, any of the destination to source direction link layer core parameters has been increased in the CONNECT message from the called user; 5. At the destination end, the destination to source direction Cir in the CONNECT message is smaller than the corresponding minimum acceptable Cir signaled to the called user; 6. At the source end, any of the source to destination direction link layer core parameters in the CONNECT message from the destination end has been increased; 7. At the source end, the source to destination direction Cir, after negotiation, is smaller than the corresponding minimum acceptable Cir; 8. The network has received a STATUS message from the user with an incompatible Q.933 state. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigQualityOfServiceNotAvailable 1.1.562.2.4.1.123.6.17.1.9
This attribute counts the number of incoming and outgoing SVCs that are rejected because the quality of service requested cannot be met by the network. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigSetupTimeout 1.1.562.2.4.1.123.6.17.1.10
This attribute counts the number of times the T303 setup timer has expired. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigLastCauseInStatusMsgReceived 1.1.562.2.4.1.123.6.17.1.11
This attribute shows the cause value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is 0 which means that no STATUS message has been received for an existing call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mpanlSigLastStateInStatusMsgReceived 1.1.562.2.4.1.123.6.17.1.12
This attribute shows the state value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), n2(2), outgoingCallProceeding(3), n4(4), n5(5), callPresent(6), n7(7), n8(8), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), n13(13), n14(14), n15(15), n16(16), n17(17), n18(18), releaseRequest(19), notApplicable(20), n21(21), n22(22), n23(23), n24(24), n25(25), n26(26), n27(27), n28(28), n29(29), n30(30), n31(31), n32(32), n33(33), n34(34), n35(35), n36(36), n37(37), n38(38), n39(39), n40(40), n41(41), n42(42), n43(43), n44(44), n45(45), n46(46), n47(47), n48(48), n49(49), n50(50), n51(51), n52(52), n53(53), n54(54), n55(55), n56(56), n57(57), n58(58), n59(59), n60(60), n61(61), n62(62), n63(63)  

mpanlSigLastDlciReceivedStatus 1.1.562.2.4.1.123.6.17.1.13
This attribute shows the value of the DLCI that has most recently received a STATUS message from the user. The initial value of this attribute is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 17..1007  

mpanlSigLastQ933StateReceivedStatus 1.1.562.2.4.1.123.6.17.1.14
This attribute shows the network Q.933 state of the DLCI that has most recently received a STATUS message from the user. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), outgoingCallProceeding(3), callPresent(6), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20)  

mpanlSigLastTimeMsgBlockCongested 1.1.562.2.4.1.123.6.17.1.15
This attribute displays the most recent time that an SVC DLCI has failed to get a message block due to message block congestion. Exceptional behavior can occur due to this. The DLCI that has most recently encountered this is indicated by the lastDlciWithMsgBlockCongestion attribute. However, all SVC DLCIs may be affected. The initial value of this attribute is 0000-00-00 00:00.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnterpriseDateAndTime Size(0|16)  

mpanlSigLastDlciWithMsgBlockCongestion 1.1.562.2.4.1.123.6.17.1.16
This attribute shows the value of the DLCI that has most recently failed to get a message block due to message block congestion. The initial value of this attribute is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mpanlSigLapfStatusTable 1.1.562.2.4.1.123.6.18
This group contains the Q.922 SVC data link layer status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigLapfStatusEntry

mpanlSigLapfStatusEntry 1.1.562.2.4.1.123.6.18.1
An entry in the mpanlSigLapfStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigLapfStatusEntry  

mpanlSigCurrentState 1.1.562.2.4.1.123.6.18.1.1
This attribute shows the current state of the SVC data link layer interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), disconnectRequest(4), informationTransfer(5), waitingAck(7)  

mpanlSigLastStateChangeReason 1.1.562.2.4.1.123.6.18.1.2
This attribute shows the reason for the most recent state change. notStarted - this is the default state after SVC data link has just been created. abmeEntered - SVC data link has entered Asynchronous Balanced Mode after SABME or UA has been received. abmeReset - the data link has been reset. dmReceived - DM response received. dmSent - DM sent. discReceived - DISC response received. discSent - DISC sent. frmrReceived - FRMR received. n200RetranTimeOut - retransmitLimit has been exceeded. other - unspecified state change reasons. The most likely reason for this is the transition from state waitingAck to state informationTransfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), abmeEntered(3), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), n200RetranTimeOut(12), other(13)  

mpanlSigFrmrReceive 1.1.562.2.4.1.123.6.18.1.3
This attribute shows the information field of the FRMR most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..8)  

mpanlSigCurrentQueueSize 1.1.562.2.4.1.123.6.18.1.4
This attribute shows the current number of frames in the SVC data link layer transmit queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigLapfStatsTable 1.1.562.2.4.1.123.6.19
This group contains the statistics for the SVC data link layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigLapfStatsEntry

mpanlSigLapfStatsEntry 1.1.562.2.4.1.123.6.19.1
An entry in the mpanlSigLapfStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigLapfStatsEntry  

mpanlSigStateChange 1.1.562.2.4.1.123.6.19.1.1
This attribute counts the number of times the SVC data link layer interface has changed state. Frequent state changes may indicate a problem with the line quality. While the data link layer is in informationTransfer state, this counter will increment on each expiry of idleProbeTimer as its state goes from informationTransfer to waitingAck and back. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigRemoteBusy 1.1.562.2.4.1.123.6.19.1.2
This attribute counts the number of times transmission of an I-frame was unsuccessful due to a perceived remote busy condition (window closed or remote busy). When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigReceiveRejectFrame 1.1.562.2.4.1.123.6.19.1.3
This attribute counts the number of REJ frames received by the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigAckTimeout 1.1.562.2.4.1.123.6.19.1.4
This attribute counts the number of times the ackTimer has expired. Frequent increments of this counter indicate a problem at the link or improper values have been chosen for ackTimer and ackDelayTimer between the local and remote sides. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigIFramesTransmitted 1.1.562.2.4.1.123.6.19.1.5
This attribute counts the number of SVC I-frames transmitted to the interface on DLCI 0. An I-frame may be counted more than once if there are retransmissions at the SVC data link layer. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigIFramesTxDiscarded 1.1.562.2.4.1.123.6.19.1.6
This attribute counts the number of SVC I-frames that are bound for the link but have been discarded. Discard reasons may be one of the following: 1. the frame length is beyond allow limit. 2. the SVC data link layer is in disconnected state. 3. the transmit queue has been purged because the queue length has reached the reset threshold. 4. the transmit queue or the queue waiting for acknowledgment has been purged because the link cannot be re-established. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigIFramesReceived 1.1.562.2.4.1.123.6.19.1.7
This attribute counts the number of SVC I-frames received from the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigIFramesRcvdDiscarded 1.1.562.2.4.1.123.6.19.1.8
This attribute counts the number of SVC I-frames received but have been discarded. The discard reasons are: 1. incorrect frame size 2. frame is out of sequence 3. frame received while the network side of the SVC data link layer is not in the informationTransfer or waitingAck state. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanl 1.1.562.2.4.1.123.7
OBJECT IDENTIFIER    

mpanlSigMpanlRowStatusTable 1.1.562.2.4.1.123.7.1
This entry controls the addition and deletion of mpanlSigMpanl components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlRowStatusEntry

mpanlSigMpanlRowStatusEntry 1.1.562.2.4.1.123.7.1.1
A single entry in the table represents a single mpanlSigMpanl component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlRowStatusEntry  

mpanlSigMpanlRowStatus 1.1.562.2.4.1.123.7.1.1.1
This variable is used as the basis for SNMP naming of mpanlSigMpanl components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlSigMpanlComponentName 1.1.562.2.4.1.123.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlSigMpanlStorageType 1.1.562.2.4.1.123.7.1.1.4
This variable represents the storage type value for the mpanlSigMpanl tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlSigMpanlIndex 1.1.562.2.4.1.123.7.1.1.10
This variable represents the index for the mpanlSigMpanl tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlSigMpanlStateTable 1.1.562.2.4.1.123.7.10
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlStateEntry

mpanlSigMpanlStateEntry 1.1.562.2.4.1.123.7.10.1
An entry in the mpanlSigMpanlStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlStateEntry  

mpanlSigMpanlAdminState 1.1.562.2.4.1.123.7.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mpanlSigMpanlOperationalState 1.1.562.2.4.1.123.7.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mpanlSigMpanlUsageState 1.1.562.2.4.1.123.7.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mpanlSigMpanlProfileTable 1.1.562.2.4.1.123.7.11
This group contains attributes which are populated by the information received from the MPA in the Profile Association command of the MPANL protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlProfileEntry

mpanlSigMpanlProfileEntry 1.1.562.2.4.1.123.7.11.1
An entry in the mpanlSigMpanlProfileTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlProfileEntry  

mpanlSigMpanlDteCustomerId 1.1.562.2.4.1.123.7.11.1.1
This attribute indicates the Customer ID of the MPA connected to this Mpanl interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mpanlSigMpanlDteNodeId 1.1.562.2.4.1.123.7.11.1.2
This attribute indicates the nodeId that uniquely identifies the MPA connected to this Mpanl interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4095  

mpanlSigMpanlDteComponentName 1.1.562.2.4.1.123.7.11.1.3
This attribute indicates the component name provided by the MPA connected to this MPANL interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(1..255)  

mpanlSigMpanlHighestDlci 1.1.562.2.4.1.123.7.11.1.4
This gives the highest DLCI that the Mpanl interface will assign to an SVC. This value is populated by information provided in the DLCI Range Information Element of the MPANL Profile Association command received from the MPA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 17..1007  

mpanlSigMpanlStatsTable 1.1.562.2.4.1.123.7.12
This group contains the statistics related to the Mpanl signaling layer at the interface level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlStatsEntry

mpanlSigMpanlStatsEntry 1.1.562.2.4.1.123.7.12.1
An entry in the mpanlSigMpanlStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlStatsEntry  

mpanlSigMpanlProtocolErrors 1.1.562.2.4.1.123.7.12.1.1
This attribute counts the number of times an Mpanl protocol error has occurred. Any one of the following events constitutes a protocol error: 1. DNA association before profile association. 2. Mandatory IE absent in SAPcommands. 3. Invalid length of IE/sub-info fields in SAP command. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlSap0CommandsRx 1.1.562.2.4.1.123.7.12.1.2
This attribute counts the number of SAP-0 commands received on the MPANL DLCI 16. This counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlSap0CommandsTx 1.1.562.2.4.1.123.7.12.1.3
This attribute counts the number of SAP-0 commands sent on the MPANL DLCI 16. This counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlSapXCommandsRx 1.1.562.2.4.1.123.7.12.1.4
This attribute counts the number of SAP-X commands received on the MPANL DLCI 16. This counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlSapXCommandsTx 1.1.562.2.4.1.123.7.12.1.5
This attribute counts the number of SAP-X commands sent on the MPANL DLCI 16. This counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlLapfStatusTable 1.1.562.2.4.1.123.7.13
This group contains the Q.922 SVC data link layer status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlLapfStatusEntry

mpanlSigMpanlLapfStatusEntry 1.1.562.2.4.1.123.7.13.1
An entry in the mpanlSigMpanlLapfStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlLapfStatusEntry  

mpanlSigMpanlCurrentState 1.1.562.2.4.1.123.7.13.1.1
This attribute shows the current state of the SVC data link layer interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), disconnectRequest(4), informationTransfer(5), waitingAck(7)  

mpanlSigMpanlLastStateChangeReason 1.1.562.2.4.1.123.7.13.1.2
This attribute shows the reason for the most recent state change. notStarted - this is the default state after SVC data link has just been created. abmeEntered - SVC data link has entered Asynchronous Balanced Mode after SABME or UA has been received. abmeReset - the data link has been reset. dmReceived - DM response received. dmSent - DM sent. discReceived - DISC response received. discSent - DISC sent. frmrReceived - FRMR received. n200RetranTimeOut - retransmitLimit has been exceeded. other - unspecified state change reasons. The most likely reason for this is the transition from state waitingAck to state informationTransfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), abmeEntered(3), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), n200RetranTimeOut(12), other(13)  

mpanlSigMpanlFrmrReceive 1.1.562.2.4.1.123.7.13.1.3
This attribute shows the information field of the FRMR most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..8)  

mpanlSigMpanlCurrentQueueSize 1.1.562.2.4.1.123.7.13.1.4
This attribute shows the current number of frames in the SVC data link layer transmit queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlLapfStatsTable 1.1.562.2.4.1.123.7.14
This group contains the statistics for the SVC data link layer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlSigMpanlLapfStatsEntry

mpanlSigMpanlLapfStatsEntry 1.1.562.2.4.1.123.7.14.1
An entry in the mpanlSigMpanlLapfStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlSigMpanlLapfStatsEntry  

mpanlSigMpanlStateChange 1.1.562.2.4.1.123.7.14.1.1
This attribute counts the number of times the SVC data link layer interface has changed state. Frequent state changes may indicate a problem with the line quality. While the data link layer is in informationTransfer state, this counter will increment on each expiry of idleProbeTimer as its state goes from informationTransfer to waitingAck and back. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlRemoteBusy 1.1.562.2.4.1.123.7.14.1.2
This attribute counts the number of times transmission of an I-frame was unsuccessful due to a perceived remote busy condition (window closed or remote busy). When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlReceiveRejectFrame 1.1.562.2.4.1.123.7.14.1.3
This attribute counts the number of REJ frames received by the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlAckTimeout 1.1.562.2.4.1.123.7.14.1.4
This attribute counts the number of times the ackTimer has expired. Frequent increments of this counter indicate a problem at the link or improper values have been chosen for ackTimer and ackDelayTimer between the local and remote sides. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlIFramesTransmitted 1.1.562.2.4.1.123.7.14.1.5
This attribute counts the number of SVC I-frames transmitted to the interface on DLCI 0. An I-frame may be counted more than once if there are retransmissions at the SVC data link layer. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlIFramesTxDiscarded 1.1.562.2.4.1.123.7.14.1.6
This attribute counts the number of SVC I-frames that are bound for the link but have been discarded. Discard reasons may be one of the following: 1. the frame length is beyond allow limit. 2. the SVC data link layer is in disconnected state. 3. the transmit queue has been purged because the queue length has reached the reset threshold. 4. the transmit queue or the queue waiting for acknowledgment has been purged because the link cannot be re-established. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlIFramesReceived 1.1.562.2.4.1.123.7.14.1.7
This attribute counts the number of SVC I-frames received from the interface. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlSigMpanlIFramesRcvdDiscarded 1.1.562.2.4.1.123.7.14.1.8
This attribute counts the number of SVC I-frames received but have been discarded. The discard reasons are: 1. incorrect frame size 2. frame is out of sequence 3. frame received while the network side of the SVC data link layer is not in the informationTransfer or waitingAck state. When this count reaches maximum, it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mpanlLmi 1.1.562.2.4.1.123.8
OBJECT IDENTIFIER    

mpanlLmiRowStatusTable 1.1.562.2.4.1.123.8.1
This entry controls the addition and deletion of mpanlLmi components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlLmiRowStatusEntry

mpanlLmiRowStatusEntry 1.1.562.2.4.1.123.8.1.1
A single entry in the table represents a single mpanlLmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlLmiRowStatusEntry  

mpanlLmiRowStatus 1.1.562.2.4.1.123.8.1.1.1
This variable is used as the basis for SNMP naming of mpanlLmi components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mpanlLmiComponentName 1.1.562.2.4.1.123.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mpanlLmiStorageType 1.1.562.2.4.1.123.8.1.1.4
This variable represents the storage type value for the mpanlLmi tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mpanlLmiIndex 1.1.562.2.4.1.123.8.1.1.10
This variable represents the index for the mpanlLmi tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mpanlLmiParmsTable 1.1.562.2.4.1.123.8.10
This group contains the provisionable attributes of the Local Management Interface component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpanlLmiParmsEntry

mpanlLmiParmsEntry 1.1.562.2.4.1.123.8.10.1
An entry in the mpanlLmiParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MpanlLmiParmsEntry  

mpanlLmiProcedures 1.1.562.2.4.1.123.8.10.1.1
This attribute selects the procedures to be used for the Local Management Interface. For the MPANL service this attribute is always set to none. none : no Local Management Interface procedures are running on this interface. This accomodates MPANL user equipment that have not implemented any LMI procedures. The remaining attributes of this group will be ignored. vendorForum : Local Management Interface procedures from the Vendor Forum specification are supported on this interface. DLCI 1023 is used for the LMI protocol. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol. ccitt: Local Management Interface procedures from the CCITT specification are supported. DLCI 0 is used for the LMI protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), vendorForum(1), ansi(2), ccitt(3)  

mpanlLmiStateTable 1.1.562.2.4.1.123.8.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF