TIMETRA-SDP-MIB

File: TIMETRA-SDP-MIB.mib (401579 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB INET-ADDRESS-MIB TIMETRA-TC-MIB
TIMETRA-SERV-MIB TIMETRA-GLOBAL-MIB TIMETRA-FILTER-MIB
TIMETRA-CHASSIS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Gauge32 Integer32 Unsigned32
IpAddress Counter64 Counter32
OBJECT-GROUP NOTIFICATION-GROUP MODULE-COMPLIANCE
RowStatus MacAddress TimeStamp
DisplayString TruthValue InterfaceIndexOrZero
InetAddressType InetAddress ServiceAdminStatus
TmnxActionType TmnxAdminState TmnxServId
TmnxCustId TNamedItem SdpBindId
TNamedItemOrEmpty TmnxVRtrMplsLspID TmnxOperState
TmnxIgmpVersion TmnxEnabledDisabled TItemDescription
TPolicyStatementNameOrEmpty TCpmProtPolicyID TmnxVPNRouteDistinguisher
TmnxPwGlobalId TmnxSpokeSdpId TmnxPwGlobalIdOrZero
TmnxBsxTransitIpPolicyIdOrZero TmnxBsxTransPrefPolicyIdOrZero TmnxBsxAarpIdOrZero
TmnxBsxAarpServiceRefType TmnxPortID TmnxVcId
TSdpIngressPolicyID TSdpEgressPolicyID TQosQGrpInstanceIDorZero
TmnxMplsTpGlobalID TmnxMplsTpNodeID tmnxServObjs
tmnxServConformance tmnxServNotifications tmnxSvcObjs
custId svcId svcVpnId
tstpTraps tmnxOtherBridgeId tmnxCustomerBridgeId
tmnxCustomerRootBridgeId tmnxOldSdpBindTlsStpPortState svcTlsStpDesignatedRoot
tlsDhcpPacketProblem svcDhcpLseStateNewCiAddr svcDhcpLseStateNewChAddr
svcDhcpLseStateOldCiAddr svcDhcpLseStateOldChAddr svcDhcpClientLease
svcDhcpLseStatePopulateError svcTlsMacMoveMaxRate svcDhcpProxyError
svcDhcpCoAError svcDhcpPacketProblem svcDhcpSubAuthError
ServObjName ServObjDesc VpnId
SdpId PWTemplateId TlsBpduTranslation
TlsLimitMacMoveLevel TlsLimitMacMove SdpBindVcType
StpExceptionCondition LspIdList BridgeId
TStpPortState StpPortRole StpProtocol
MvplsPruneState TdmOptionsSigPkts TdmOptionsCasTrunkFraming
SdpBFHundredthsOfPercent SdpBindBandwidth L2ptProtocols
L2RouteOrigin ConfigStatus TmnxSiteId
protectedMacForNotify timetraSRMIBModules TFilterID
tmnxChassisIndex tmnxCardSlotNum tmnxMDASlotNum

Defined Types

SdpInfoEntry  
SEQUENCE    
  sdpId SdpId
  sdpRowStatus RowStatus
  sdpDelivery INTEGER
  sdpFarEndIpAddress IpAddress
  sdpLspList LspIdList
  sdpDescription ServObjDesc
  sdpLabelSignaling INTEGER
  sdpAdminStatus ServiceAdminStatus
  sdpOperStatus INTEGER
  sdpAdminPathMtu INTEGER
  sdpOperPathMtu Integer32
  sdpKeepAliveAdminStatus INTEGER
  sdpKeepAliveOperStatus INTEGER
  sdpKeepAliveHelloTime INTEGER
  sdpKeepAliveMaxDropCount INTEGER
  sdpKeepAliveHoldDownTime INTEGER
  sdpLastMgmtChange TimeStamp
  sdpKeepAliveHelloMessageLength INTEGER
  sdpKeepAliveNumHelloRequestMessages Unsigned32
  sdpKeepAliveNumHelloResponseMessages Unsigned32
  sdpKeepAliveNumLateHelloResponseMessages Unsigned32
  sdpKeepAliveHelloRequestTimeout INTEGER
  sdpLdpEnabled TruthValue
  sdpVlanVcEtype Unsigned32
  sdpAdvertisedVllMtuOverride TruthValue
  sdpOperFlags BITS
  sdpLastStatusChange TimeStamp
  sdpMvplsMgmtService TmnxServId
  sdpMvplsMgmtSdpBndId SdpBindId
  sdpCollectAcctStats TruthValue
  sdpAccountingPolicyId Unsigned32
  sdpClassFwdingEnabled TruthValue
  sdpClassFwdingDefaultLsp TmnxVRtrMplsLspID
  sdpClassFwdingMcLsp TmnxVRtrMplsLspID
  sdpMetric Unsigned32
  sdpAutoSdp TruthValue
  sdpSnmpAllowed TruthValue
  sdpPBBEtype Unsigned32
  sdpBandwidthBookingFactor Unsigned32
  sdpOperBandwidth Unsigned32
  sdpAvailableBandwidth Unsigned32
  sdpMaxBookableBandwidth Unsigned32
  sdpBookedBandwidth Unsigned32
  sdpCreationOrigin L2RouteOrigin
  sdpEnforceDiffServLspFc TruthValue
  sdpMixedLspModeEnabled TruthValue
  sdpLspRevertTime Integer32
  sdpLspRevertTimeCountDown Integer32
  sdpLdpLspId Unsigned32
  sdpLdpActive TruthValue
  sdpNetDomainName TNamedItemOrEmpty
  sdpEgressIfsNetDomainConsistent INTEGER
  sdpBgpTunnelEnabled TruthValue
  sdpBgpTunnelLspId Unsigned32
  sdpTunnelFarEndIpAddress IpAddress
  sdpActiveLspType INTEGER
  sdpBindingPort TmnxPortID
  sdpFarEndNodeId TmnxMplsTpNodeID
  sdpFarEndGlobalId TmnxMplsTpGlobalID

SdpBindEntry  
SEQUENCE    
  sdpBindId SdpBindId
  sdpBindRowStatus RowStatus
  sdpBindAdminIngressLabel Unsigned32
  sdpBindAdminEgressLabel Unsigned32
  sdpBindOperIngressLabel Unsigned32
  sdpBindOperEgressLabel Unsigned32
  sdpBindAdminStatus ServiceAdminStatus
  sdpBindOperStatus INTEGER
  sdpBindLastMgmtChange TimeStamp
  sdpBindType INTEGER
  sdpBindIngressMacFilterId TFilterID
  sdpBindIngressIpFilterId TFilterID
  sdpBindEgressMacFilterId TFilterID
  sdpBindEgressIpFilterId TFilterID
  sdpBindVpnId VpnId
  sdpBindCustId TmnxCustId
  sdpBindVcType SdpBindVcType
  sdpBindVlanVcTag Unsigned32
  sdpBindSplitHorizonGrp ServObjName
  sdpBindOperFlags BITS
  sdpBindLastStatusChange TimeStamp
  sdpBindIesIfIndex InterfaceIndexOrZero
  sdpBindMacPinning TmnxEnabledDisabled
  sdpBindIngressIpv6FilterId TFilterID
  sdpBindEgressIpv6FilterId TFilterID
  sdpBindCollectAcctStats TruthValue
  sdpBindAccountingPolicyId Unsigned32
  sdpBindPwPeerStatusBits BITS
  sdpBindPeerVccvCvBits BITS
  sdpBindPeerVccvCcBits BITS
  sdpBindControlWordBit TruthValue
  sdpBindOperControlWord TruthValue
  sdpBindEndPoint ServObjName
  sdpBindEndPointPrecedence Unsigned32
  sdpBindIsICB TruthValue
  sdpBindPwFaultInetAddressType InetAddressType
  sdpBindPwFaultInetAddress InetAddress
  sdpBindClassFwdingOperState TmnxOperState
  sdpBindForceVlanVcForwarding TruthValue
  sdpBindAdminBandwidth SdpBindBandwidth
  sdpBindOperBandwidth SdpBindBandwidth
  sdpBindCreationOrigin L2RouteOrigin
  sdpBindDescription TItemDescription
  sdpBindSiteName TNamedItemOrEmpty
  sdpBindHashLabel TruthValue
  sdpBindIsaAaApplicationProfile ServObjName
  sdpBindStandbySigSlave TruthValue
  sdpBindHashLabelSignalCapability TruthValue
  sdpBindIngressFlowspec TruthValue
  sdpBindCpmProtPolicyId TCpmProtPolicyID
  sdpBindCpmProtMonitorMac TruthValue
  sdpBindCpmProtEthCfmMonitorFlags BITS
  sdpBindTransitIpPolicyId TmnxBsxTransitIpPolicyIdOrZero
  sdpBindPwStatusSignaling TruthValue
  sdpBindOperGrp TNamedItemOrEmpty
  sdpBindMonitorOperGrp TNamedItemOrEmpty
  sdpBindOperHashLabel TruthValue
  sdpBindTransitPrefixPolicyId TmnxBsxTransPrefPolicyIdOrZero
  sdpBindAarpId TmnxBsxAarpIdOrZero
  sdpBindIngressQoSNetworkPlcyId TSdpIngressPolicyID
  sdpBindEgressQoSNetworkPlcyId TSdpEgressPolicyID
  sdpBindIngressQoSFpRedirectQGrp TNamedItemOrEmpty
  sdpBindEgressQoSPortRedirectQGrp TNamedItemOrEmpty
  sdpBindIngressQoSInstanceId TQosQGrpInstanceIDorZero
  sdpBindEgressQoSInstanceId TQosQGrpInstanceIDorZero
  sdpBindAarpServRefType TmnxBsxAarpServiceRefType
  sdpBindPwLocalStatusBits BITS
  sdpBindBlockOnPeerFault TruthValue

SdpBindBaseStatsEntry  
SEQUENCE    
  sdpBindBaseStatsIngressForwardedPackets Counter64
  sdpBindBaseStatsIngressDroppedPackets Counter64
  sdpBindBaseStatsEgressForwardedPackets Counter64
  sdpBindBaseStatsEgressForwardedOctets Counter64
  sdpBindBaseStatsCustId TmnxCustId
  sdpBindBaseStatsIngFwdOctets Counter64
  sdpBindBaseStatsIngDropOctets Counter64

SdpBindTlsEntry  
SEQUENCE    
  sdpBindTlsStpAdminStatus TmnxEnabledDisabled
  sdpBindTlsStpPriority INTEGER
  sdpBindTlsStpPortNum INTEGER
  sdpBindTlsStpPathCost INTEGER
  sdpBindTlsStpRapidStart TmnxEnabledDisabled
  sdpBindTlsStpBpduEncap INTEGER
  sdpBindTlsStpPortState TStpPortState
  sdpBindTlsStpDesignatedBridge BridgeId
  sdpBindTlsStpDesignatedPort Integer32
  sdpBindTlsStpForwardTransitions Gauge32
  sdpBindTlsStpInConfigBpdus Gauge32
  sdpBindTlsStpInTcnBpdus Gauge32
  sdpBindTlsStpInBadBpdus Gauge32
  sdpBindTlsStpOutConfigBpdus Gauge32
  sdpBindTlsStpOutTcnBpdus Gauge32
  sdpBindTlsStpOperBpduEncap INTEGER
  sdpBindTlsStpVpnId VpnId
  sdpBindTlsStpCustId TmnxCustId
  sdpBindTlsMacAddressLimit Integer32
  sdpBindTlsNumMacAddresses Integer32
  sdpBindTlsNumStaticMacAddresses Integer32
  sdpBindTlsMacLearning TmnxEnabledDisabled
  sdpBindTlsMacAgeing TmnxEnabledDisabled
  sdpBindTlsStpOperEdge TruthValue
  sdpBindTlsStpAdminPointToPoint INTEGER
  sdpBindTlsStpPortRole StpPortRole
  sdpBindTlsStpAutoEdge TmnxEnabledDisabled
  sdpBindTlsStpOperProtocol StpProtocol
  sdpBindTlsStpInRstBpdus Gauge32
  sdpBindTlsStpOutRstBpdus Gauge32
  sdpBindTlsLimitMacMove TlsLimitMacMove
  sdpBindTlsDiscardUnknownSource TmnxEnabledDisabled
  sdpBindTlsMvplsPruneState MvplsPruneState
  sdpBindTlsMvplsMgmtService TmnxServId
  sdpBindTlsMvplsMgmtSdpBndId SdpBindId
  sdpBindTlsStpException StpExceptionCondition
  sdpBindTlsL2ptTermination TmnxEnabledDisabled
  sdpBindTlsBpduTranslation TlsBpduTranslation
  sdpBindTlsStpRootGuard TruthValue
  sdpBindTlsStpInMstBpdus Gauge32
  sdpBindTlsStpOutMstBpdus Gauge32
  sdpBindTlsStpRxdDesigBridge BridgeId
  sdpBindTlsMacMoveNextUpTime Unsigned32
  sdpBindTlsMacMoveRateExcdLeft Unsigned32
  sdpBindTlsLimitMacMoveLevel TlsLimitMacMoveLevel
  sdpBindTlsBpduTransOper INTEGER
  sdpBindTlsL2ptProtocols L2ptProtocols
  sdpBindTlsIgnoreStandbySig TruthValue
  sdpBindTlsBlockOnMeshFail TruthValue
  sdpBindTlsInTcBitBpdus Counter32
  sdpBindTlsOutTcBitBpdus Counter32
  sdpBindTlsRestProtSrcMac TruthValue
  sdpBindTlsRestProtSrcMacAction INTEGER
  sdpBindTlsAutoLearnMacProtect TruthValue

SdpBindMeshTlsEntry  
SEQUENCE    
  sdpBindMeshTlsPortState TStpPortState
  sdpBindMeshTlsHoldDownTimer INTEGER
  sdpBindMeshTlsTransitionState INTEGER
  sdpBindMeshTlsNotInMstRegion TruthValue
  sdpBindMeshTlsRestProtSrcMac TruthValue
  sdpBindMeshTlsRestProtSrcMacAct INTEGER
  sdpBindMeshTlsAutoLearnMacProt TruthValue

SdpBindApipeEntry  
SEQUENCE    
  sdpBindApipeAdminConcatCellCount Integer32
  sdpBindApipeSigConcatCellCount Integer32
  sdpBindApipeOperConcatCellCount Integer32
  sdpBindApipeConcatMaxDelay Integer32
  sdpBindApipeConcatCellClp TruthValue
  sdpBindApipeConcatCellAal5Fr TruthValue

SdpBindDhcpInfoEntry  
SEQUENCE    
  sdpBindDhcpDescription ServObjDesc
  sdpBindDhcpSnoop TmnxEnabledDisabled

SdpBindDhcpStatsEntry  
SEQUENCE    
  sdpBindDhcpStatsClntSnoopdPckts Counter32
  sdpBindDhcpStatsSrvrSnoopdPckts Counter32
  sdpBindDhcpStatsClntForwdPckts Counter32
  sdpBindDhcpStatsSrvrForwdPckts Counter32
  sdpBindDhcpStatsClntDropdPckts Counter32
  sdpBindDhcpStatsSrvrDropdPckts Counter32
  sdpBindDhcpStatsClntProxRadPckts Counter32
  sdpBindDhcpStatsClntProxLSPckts Counter32
  sdpBindDhcpStatsGenReleasePckts Counter32
  sdpBindDhcpStatsGenForceRenPckts Counter32

SdpBindIpipeEntry  
SEQUENCE    
  sdpBindIpipeCeInetAddressType InetAddressType
  sdpBindIpipeCeInetAddress InetAddress
  sdpBindIpipePeerCeInetAddrType InetAddressType
  sdpBindIpipePeerCeInetAddr InetAddress
  sdpBindIpipePeerIpv6Capability TruthValue
  sdpBindIpipePeerLLCeInetAddr InetAddress
  sdpBindIpipePeerGlobalCeInetAddr InetAddress

SdpFCMappingEntry  
SEQUENCE    
  sdpFCMappingFCName TNamedItem
  sdpFCMappingRowStatus RowStatus
  sdpFCMappingLspId TmnxVRtrMplsLspID

SdpBindCpipeEntry  
SEQUENCE    
  sdpBindCpipeLocalPayloadSize Unsigned32
  sdpBindCpipePeerPayloadSize Unsigned32
  sdpBindCpipeLocalBitrate Unsigned32
  sdpBindCpipePeerBitrate Unsigned32
  sdpBindCpipeLocalSigPkts TdmOptionsSigPkts
  sdpBindCpipePeerSigPkts TdmOptionsSigPkts
  sdpBindCpipeLocalCasTrunkFraming TdmOptionsCasTrunkFraming
  sdpBindCpipePeerCasTrunkFraming TdmOptionsCasTrunkFraming
  sdpBindCpipeLocalUseRtpHeader TruthValue
  sdpBindCpipePeerUseRtpHeader TruthValue
  sdpBindCpipeLocalDifferential TruthValue
  sdpBindCpipePeerDifferential TruthValue
  sdpBindCpipeLocalTimestampFreq Unsigned32
  sdpBindCpipePeerTimestampFreq Unsigned32

SdpBindTlsMfibAllowedMdaEntry  
SEQUENCE    
  sdpBindTlsMfibMdaRowStatus RowStatus

SdpBindTlsL2ptStatsEntry  
SEQUENCE    
  sdpBindTlsL2ptStatsLastClearedTime TimeStamp
  sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusTx Counter32
  sdpBindTlsL2ptStatsStpConfigBpdusRx Counter32
  sdpBindTlsL2ptStatsStpConfigBpdusTx Counter32
  sdpBindTlsL2ptStatsStpRstBpdusRx Counter32
  sdpBindTlsL2ptStatsStpRstBpdusTx Counter32
  sdpBindTlsL2ptStatsStpTcnBpdusRx Counter32
  sdpBindTlsL2ptStatsStpTcnBpdusTx Counter32
  sdpBindTlsL2ptStatsPvstConfigBpdusRx Counter32
  sdpBindTlsL2ptStatsPvstConfigBpdusTx Counter32
  sdpBindTlsL2ptStatsPvstRstBpdusRx Counter32
  sdpBindTlsL2ptStatsPvstRstBpdusTx Counter32
  sdpBindTlsL2ptStatsPvstTcnBpdusRx Counter32
  sdpBindTlsL2ptStatsPvstTcnBpdusTx Counter32
  sdpBindTlsL2ptStatsOtherBpdusRx Counter32
  sdpBindTlsL2ptStatsOtherBpdusTx Counter32
  sdpBindTlsL2ptStatsOtherL2ptBpdusRx Counter32
  sdpBindTlsL2ptStatsOtherL2ptBpdusTx Counter32
  sdpBindTlsL2ptStatsOtherInvalidBpdusRx Counter32
  sdpBindTlsL2ptStatsOtherInvalidBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapCdpBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapCdpBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapVtpBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapVtpBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapDtpBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapDtpBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPagpBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapPagpBpdusTx Counter32
  sdpBindTlsL2ptStatsL2ptEncapUdldBpdusRx Counter32
  sdpBindTlsL2ptStatsL2ptEncapUdldBpdusTx Counter32
  sdpBindTlsL2ptStatsCdpBpdusRx Counter32
  sdpBindTlsL2ptStatsCdpBpdusTx Counter32
  sdpBindTlsL2ptStatsVtpBpdusRx Counter32
  sdpBindTlsL2ptStatsVtpBpdusTx Counter32
  sdpBindTlsL2ptStatsDtpBpdusRx Counter32
  sdpBindTlsL2ptStatsDtpBpdusTx Counter32
  sdpBindTlsL2ptStatsPagpBpdusRx Counter32
  sdpBindTlsL2ptStatsPagpBpdusTx Counter32
  sdpBindTlsL2ptStatsUdldBpdusRx Counter32
  sdpBindTlsL2ptStatsUdldBpdusTx Counter32

PwTemplateEntry  
SEQUENCE    
  pwTemplateId PWTemplateId
  pwTemplateRowStatus RowStatus
  pwTemplateLastChanged TimeStamp
  pwTemplateUseProvisionedSdp TruthValue
  pwTemplateVcType SdpBindVcType
  pwTemplateAccountingPolicyId Unsigned32
  pwTemplateCollectAcctStats TruthValue
  pwTemplateMacLearning TmnxEnabledDisabled
  pwTemplateMacAgeing TmnxEnabledDisabled
  pwTemplateDiscardUnknownSource TmnxEnabledDisabled
  pwTemplateLimitMacMove TlsLimitMacMove
  pwTemplateMacPinning TmnxEnabledDisabled
  pwTemplateVlanVcTag Unsigned32
  pwTemplateMacAddressLimit Unsigned32
  pwTemplateShgName TNamedItemOrEmpty
  pwTemplateShgDescription TItemDescription
  pwTemplateShgRestProtSrcMac TruthValue
  pwTemplateShgRestUnprotDstMac TruthValue
  pwTemplateEgressMacFilterId TFilterID
  pwTemplateEgressIpFilterId TFilterID
  pwTemplateEgressIpv6FilterId TFilterID
  pwTemplateIngressMacFilterId TFilterID
  pwTemplateIngressIpFilterId TFilterID
  pwTemplateIngressIpv6FilterId TFilterID
  pwTemplateIgmpFastLeave TmnxEnabledDisabled
  pwTemplateIgmpImportPlcy TNamedItemOrEmpty
  pwTemplateIgmpLastMembIntvl Unsigned32
  pwTemplateIgmpMaxNbrGrps Unsigned32
  pwTemplateIgmpGenQueryIntvl Unsigned32
  pwTemplateIgmpQueryRespIntvl Unsigned32
  pwTemplateIgmpRobustCount Unsigned32
  pwTemplateIgmpSendQueries TmnxEnabledDisabled
  pwTemplateIgmpMcacPolicyName TPolicyStatementNameOrEmpty
  pwTemplateIgmpMcacUnconstBW Integer32
  pwTemplateIgmpMcacPrRsvMndBW Integer32
  pwTemplateIgmpVersion TmnxIgmpVersion
  pwTemplateForceVlanVcForwarding TruthValue
  pwTemplateHashLabel TruthValue
  pwTemplateControlWord TruthValue
  pwTemplateHashLabelSignalCap TruthValue
  pwTemplateRestProtSrcMac TruthValue
  pwTemplateRestProtSrcMacAction INTEGER
  pwTemplateAutoLearnMacProtect TruthValue
  pwTemplateShgRestProtSrcMacAct INTEGER
  pwTemplateShgAutoLearnMacProtect TruthValue
  pwTemplateIngQoSNetworkPlcyId TSdpIngressPolicyID
  pwTemplateEgrQoSNetworkPlcyId TSdpEgressPolicyID
  pwTemplateIngQoSFpRedirectQGrp TNamedItemOrEmpty
  pwTemplateEgrQoSPortRedirectQGrp TNamedItemOrEmpty
  pwTemplateIngQoSInstanceId TQosQGrpInstanceIDorZero
  pwTemplateEgrQoSInstanceId TQosQGrpInstanceIDorZero
  pwTemplateBlockOnPeerFault TruthValue

PwTemplateIgmpSnpgGrpSrcEntry  
SEQUENCE    
  pwTemplateIgmpSnpgGrpAddrType InetAddressType
  pwTemplateIgmpSnpgGrpAddr InetAddress
  pwTemplateIgmpSnpgSrcAddrType InetAddressType
  pwTemplateIgmpSnpgSrcAddr InetAddress
  pwTemplateIgmpSnpgRowStatus RowStatus
  pwTemplateIgmpSnpgLastChngd TimeStamp

PwTemplateMfibAllowedMdaEntry  
SEQUENCE    
  pwTemplateMfibMdaRowStatus RowStatus

SdpBindTlsMrpEntry  
SEQUENCE    
  sdpBindTlsMrpLastChngd TimeStamp
  sdpBindTlsMrpJoinTime Unsigned32
  sdpBindTlsMrpLeaveTime Unsigned32
  sdpBindTlsMrpLeaveAllTime Unsigned32
  sdpBindTlsMrpPeriodicTime Unsigned32
  sdpBindTlsMrpPeriodicEnabled TruthValue
  sdpBindTlsMrpRxPdus Counter32
  sdpBindTlsMrpDroppedPdus Counter32
  sdpBindTlsMrpTxPdus Counter32
  sdpBindTlsMrpRxNewEvent Counter32
  sdpBindTlsMrpRxJoinInEvent Counter32
  sdpBindTlsMrpRxInEvent Counter32
  sdpBindTlsMrpRxJoinEmptyEvent Counter32
  sdpBindTlsMrpRxEmptyEvent Counter32
  sdpBindTlsMrpRxLeaveEvent Counter32
  sdpBindTlsMrpTxNewEvent Counter32
  sdpBindTlsMrpTxJoinInEvent Counter32
  sdpBindTlsMrpTxInEvent Counter32
  sdpBindTlsMrpTxJoinEmptyEvent Counter32
  sdpBindTlsMrpTxEmptyEvent Counter32
  sdpBindTlsMrpTxLeaveEvent Counter32
  sdpBindTlsMrpPolicy TNamedItemOrEmpty

SdpBindTlsMmrpEntry  
SEQUENCE    
  sdpBindTlsMmrpMacAddr MacAddress
  sdpBindTlsMmrpDeclared TruthValue
  sdpBindTlsMmrpRegistered TruthValue
  sdpBindTlsMmrpEndStation TruthValue

SdpAutoBindBgpInfoEntry  
SEQUENCE    
  sdpAutoBindBgpInfoTemplateId PWTemplateId
  sdpAutoBindBgpInfoAGI TmnxVPNRouteDistinguisher
  sdpAutoBindBgpInfoSAII Unsigned32
  sdpAutoBindBgpInfoTAII Unsigned32

SvcTlsBgpADAutoBindPlcyEntry  
SEQUENCE    
  svcTlsBgpADPWTempBindRowStatus RowStatus
  svcTlsBgpADPWTempBindLastChngd TimeStamp
  svcTlsBgpADPWTempBindSHG TNamedItemOrEmpty
  svcTlsBgpADPWTempBindOperGrp TNamedItemOrEmpty

SvcTlsBgpADAutoBindPlcyRTEntry  
SEQUENCE    
  svcTlsBgpADPWTempBindRT TNamedItem
  svcTlsBgpADPWTempBindRTRowStat RowStatus

SvcL2RteEntry  
SEQUENCE    
  svcL2RteVsiPrefix Unsigned32
  svcL2RteRouteDistinguisher TmnxVPNRouteDistinguisher
  svcL2RteNextHopType InetAddressType
  svcL2RteNextHop InetAddress
  svcL2RteSdpBindId SdpBindId
  svcL2RtePwTemplateId PWTemplateId
  svcL2RteError DisplayString
  svcL2RteLastErrorTime TimeStamp
  svcL2RteStatus INTEGER

SvcL2BgpVplsRteEntry  
SEQUENCE    
  svcL2BgpVplsRteVeId TmnxSiteId
  svcL2BgpVplsRteRD TmnxVPNRouteDistinguisher
  svcL2BgpVplsRteNextHopType InetAddressType
  svcL2BgpVplsRteNextHop InetAddress
  svcL2BgpVplsRteSdpBindId SdpBindId
  svcL2BgpVplsRtePwTemplateId PWTemplateId
  svcL2BgpVplsRteError DisplayString
  svcL2BgpVplsRteLastErrorTime TimeStamp
  svcL2BgpVplsRteControlWord Unsigned32
  svcL2BgpVplsRtePathMtu Integer32
  svcL2BgpVplsRteState INTEGER
  svcL2BgpVplsRteSeqDelivery Unsigned32
  svcL2BgpVplsRteDF TruthValue
  svcL2BgpVplsRteStatus INTEGER

SdpBindPbbEntry  
SEQUENCE    
  sdpBindPbbSvcIdIVpls TmnxServId
  sdpBindPbbSvcIdBVpls TmnxServId
  sdpBindPbbId SdpBindId
  sdpBindPbbRowStatus RowStatus
  sdpBindPbbLastMgmtChange TimeStamp
  sdpBindPbbIgmpSnpgMRouter TruthValue

SdpBindFPropBMacAddrEntry  
SEQUENCE    
  sdpBindFPropBMacAddrOrMacNameTag INTEGER
  sdpBindFPropBMacAddrOrMacName TNamedItem
  sdpBindFPropBMacAddrRowStatus RowStatus

SdpAutoBindBgpVplsEntry  
SEQUENCE    
  sdpAutoBindBgpVplsTemplateId PWTemplateId

SdpAtBndBgp129Type2Entry  
SEQUENCE    
  sdpAtBndBgp129Type2TemplateId PWTemplateId
  sdpAtBndBgp129Type2SaiiGlobalId TmnxPwGlobalId
  sdpAtBndBgp129Type2SaiiPrefix Unsigned32
  sdpAtBndBgp129Type2SaiiAcId Unsigned32
  sdpAtBndBgp129Type2TaiiGlobalId TmnxPwGlobalId
  sdpAtBndBgp129Type2TaiiPrefix Unsigned32
  sdpAtBndBgp129Type2TaiiAcId Unsigned32

SdpBindEthCfmEntry  
SEQUENCE    
  sdpBindEthCfmRowLastChanged TimeStamp
  sdpBindEthCfmVMepFilter TruthValue

SdpBindTlsSpbEntry  
SEQUENCE    
  sdpBindTlsSpbRowStatus RowStatus
  sdpBindTlsSpbLastChgd TimeStamp
  sdpBindTlsSpbIfIndex InterfaceIndexOrZero
  sdpBindTlsSpbAdminState TmnxAdminState

SdpPwPortEntry  
SEQUENCE    
  sdpPwPortId Unsigned32
  sdpPwPortRowStatus RowStatus
  sdpPwPortLastChgd TimeStamp
  sdpPwPortAdminStatus ServiceAdminStatus
  sdpPwPortVcId TmnxVcId
  sdpPwPortEncapType INTEGER
  sdpPwPortOperStatus INTEGER
  sdpPwPortOperFlags BITS
  sdpPwPortVcType SdpBindVcType
  sdpPwPortVlanVcTag Unsigned32
  sdpPwPortEgrShapVPort TNamedItemOrEmpty
  sdpPwPortEgrShapDefIntDestId TNamedItemOrEmpty

SdpBindPwPathEntry  
SEQUENCE    
  sdpBindPwPathRowStatus RowStatus
  sdpBindPwPathLastChanged TimeStamp
  sdpBindPwPathAgi TmnxVPNRouteDistinguisher
  sdpBindPwPathSaiiGlobalId TmnxMplsTpGlobalID
  sdpBindPwPathSaiiNodeId TmnxMplsTpNodeID
  sdpBindPwPathSaiiAcId Unsigned32
  sdpBindPwPathTaiiGlobalId TmnxMplsTpGlobalID
  sdpBindPwPathTaiiNodeId TmnxMplsTpNodeID
  sdpBindPwPathTaiiAcId Unsigned32

SdpBindCtrlChanPwEntry  
SEQUENCE    
  sdpBindCtrlChanPwLastChanged TimeStamp
  sdpBindCtrlChanPwStatus TmnxEnabledDisabled
  sdpBindCtrlChanPwRefreshTimer Unsigned32
  sdpBindCtrlChanPwPeerExpired TruthValue
  sdpBindCtrlChanPwRequestTimer Unsigned32
  sdpBindCtrlChanPwRetryTimer Unsigned32
  sdpBindCtrlChanPwTimeoutMult Unsigned32
  sdpBindCtrlChanPwAck TruthValue

Defined Values

timetraServicesSdpMIBModule 1.3.6.1.4.1.6527.1.1.3.56
This document is the SNMP MIB module to manage and provision the various services of the Alcatel-Lucent SROS system. Copyright 2003-2013 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxSdpObjs 1.3.6.1.4.1.6527.3.1.2.4.4
OBJECT IDENTIFIER    

tmnxSdpNotifyObjs 1.3.6.1.4.1.6527.3.1.2.4.4.100
OBJECT IDENTIFIER    

tmnxSdpConformance 1.3.6.1.4.1.6527.3.1.1.4.4
OBJECT IDENTIFIER    

sdpTrapsPrefix 1.3.6.1.4.1.6527.3.1.3.4.4
OBJECT IDENTIFIER    

sdpTraps 1.3.6.1.4.1.6527.3.1.3.4.4.0
OBJECT IDENTIFIER    

sdpNumEntries 1.3.6.1.4.1.6527.3.1.2.4.4.1
The current number of SDPs configured in this device.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdpNextFreeId 1.3.6.1.4.1.6527.3.1.2.4.4.2
The next available value for sdpId.
Status: current Access: read-only
OBJECT-TYPE    
  SdpId  

sdpInfoTable 1.3.6.1.4.1.6527.3.1.2.4.4.3
A table that contains SDP information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpInfoEntry

sdpInfoEntry 1.3.6.1.4.1.6527.3.1.2.4.4.3.1
Information about a specific SDP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpInfoEntry  

sdpId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.1
SDP identifier.
Status: current Access: read-only
OBJECT-TYPE    
  SdpId  

sdpRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.2
This object indicates the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'. To delete an entry from this table, the corresponding SDP must be administratively down, not bound to any service, and not in use as a mirror destination.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpDelivery 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.3
This object specifies the type of delivery used by this SDP. The value of this object must be specified when the row is created and cannot be changed while the row status is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER gre(1), mpls(2)  

sdpFarEndIpAddress 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.4
This object specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. If sdpTunnelFarEndIpAddress is not set, then sdpFarEndIpAddress also specifies the remote end of the TLDP session. The value of this object must be set to a non-default value when the sdpDelivery is set to 'gre' or 'mpls' for the row to become 'active', and can only be changed while the admin status of the SDP is 'down'.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

sdpLspList 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.5
When the SDP delivery specified by sdpDelivery is 'mpls', this object specifies the list of LSPs used to reach the far-end ESR device. All the LSPs in this list must terminate at the IP address specified by sdpFarEndIpAddress or sdpFarEndNodeId (for sdpDelivery of 'mpls'). This object is otherwise insignificant and should contain a value of 0. When this list has more than one element, the Alcatel-Lucent SROS router will use all of the LSPs for load balancing purposes. Each LSP ID in the list corresponds to the vRtrMplsLspIndex of the given MPLS LSP.
Status: current Access: read-create
OBJECT-TYPE    
  LspIdList  

sdpDescription 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.6
Generic information about this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  ServObjDesc  

sdpLabelSignaling 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.7
This object specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. When the value of this object is 'none' then the labels are manually assigned at the time the SDP is bound to a service. The value of this object can only be changed while the admin status of the SDP is 'down'. An 'inconsistentValue' error is returned if this object is not set to 'none' when sdpDelivery is set to 'mpls'. Default value of this object is set to 'none' when sdpDelivery is set to 'mpls' otherwise default value for this object is set to 'tldp'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), tldp(2), bgp(3)  

sdpAdminStatus 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.8
The desired state of this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  ServiceAdminStatus  

sdpOperStatus 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.9
The operating state of this SDP. The value 'notAlive' is valid only when keep-alive is enabled, and it means that the keep-alive operating status is not alive. The value 'notReady' is valid only when this SDP uses a label signaling protocol (e.g. TLDP) and it means that the signaling session with the far-end peer has not been established. The value 'invalidEgressInterface' indicates that the IOM's have detected that the egress interface towards the far-end device is not a network port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), notAlive(2), notReady(3), invalidEgressInterface(4), transportTunnelDown(5), down(6)  

sdpAdminPathMtu 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.10
This object specifies the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. The default value of zero indicates that the path MTU should be computed dynamically from the corresponding MTU of the tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0 | 576..9194  

sdpOperPathMtu 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.11
This object specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. In order to be able to bind this SDP to a given service, the value of this object minus the control word size (if applicable) must be equal to or larger than the MTU of the service, as defined by its svcMtu.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdpKeepAliveAdminStatus 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.12
This object is used to enable or disable the keep-alive protocol used to determine the operating status of this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sdpKeepAliveOperStatus 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.13
The current status of the keep-alive protocol. The value 'alive' indicates that the far-end ESR is replying the SDP Echo Requests messages sent by this device indicating no error condition. The value 'noResponse' indicates that the number of consecutive SDP Echo Request messages unack- nowledged by the far-end ESR exceeded the limit defined by sdpKeepAliveMaxDropCount. The values 'senderIdInvalid' and 'responderIdError' are two error conditions detected by the far-end ESR. The value 'disabled' indicates that the keep-alive protocol is not enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER alive(1), noResponse(2), senderIdInvalid(3), responderIdError(4), disabled(5)  

sdpKeepAliveHelloTime 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.14
This object specifies how often the SDP Echo Request messages are transmitted on this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..3600  

sdpKeepAliveMaxDropCount 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.15
This object specifies the maximum number of consecutive SDP Echo Request messages that can be unacknowledged before the keep-alive protocol reports a fault.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..5  

sdpKeepAliveHoldDownTime 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.16
This object specifies the amount of time to wait before the keep-alive operating status is eligible to enter the 'alive' state.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..3600  

sdpLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.17
The value of sysUpTime at the time of the most recent management-initiated change to this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpKeepAliveHelloMessageLength 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.18
This object specifies the length of the SDP Echo Request messages transmitted on this SDP. The default value of zero indicates that the message length should be equal to the SDP's operating path MTU, as specified by sdpOperPathMtu. When the default value is overridden, the message length is sdpKeepAliveHelloMessageLength.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0 | 40..9198  

sdpKeepAliveNumHelloRequestMessages 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.19
The number of SDP Echo Request messages transmitted since the keep-alive was administratively enabled or the counter was cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpKeepAliveNumHelloResponseMessages 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.20
The number of SDP Echo Response messages received since the keep-alive was administratively enabled or the counter was cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpKeepAliveNumLateHelloResponseMessages 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.21
The number of SDP Echo Response messages received after the corresponding Request timeout timer expired.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpKeepAliveHelloRequestTimeout 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.22
The number of seconds to wait for an SDP Echo Response message before declaring a timeout.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..10  

sdpLdpEnabled 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.23
When the value of this object is 'true' the transport LSP's are signalled by LDP, as opposed to being provisioned static or RSVP-signalled LSP's. This object applies only to MPLS SDP's.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpVlanVcEtype 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.24
This object specifies the Ethertype used in frames sent out this SDP, when the VC type is vlan.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 600..ffff  

sdpAdvertisedVllMtuOverride 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.25
When the value of this object is 'true' the advertised MTU of a VLL spoke SDP bind includes the 14-byte L2 header, so that it is backward compatible with pre-2.0 software.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpOperFlags 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.26
This object specifies all the conditions that affect the operating status of this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  BITS sdpAdminDown(0), signalingSessionDown(1), transportTunnelDown(2), keepaliveFailure(3), invalidEgressInterface(4), noSystemIpAddress(5), transportTunnelUnstable(6), notOnBindingPort(7)  

sdpLastStatusChange 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.27
The value of sysUpTime at the time of the most recent operating status change to this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpMvplsMgmtService 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.28
The value of sdpMvplsMgmtService indicates the service Id of the service where the STP instance is running that is managing this SDP. This object is only valid if sdpMvplsMgmtService is different from 0.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxServId  

sdpMvplsMgmtSdpBndId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.29
The value of sdpMvplsMgmtSdpBndId indicates which SDP bind in the mVPLS instance specified in sdpMvplsMgmtService is controlling this SDP. This object is only valid if sdpMvplsMgmtService is different from 0.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindId  

sdpCollectAcctStats 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.30
The value of the object sdpCollectAcctStats specifies whether the agent collects accounting statistics for this SDP. When the value is 'true' the agent collects accounting statistics on this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpAccountingPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.31
The value of sdpAccountingPolicyId specifies the policy to use to collect accounting statistics on this SDP. The value zero indicates that the agent should use the default accounting policy, if one exists.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

sdpClassFwdingEnabled 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.32
The value of sdpClassFwdingEnabled specifies the admin state of class-based forwarding on this SDP. When the value is 'true', class-based forwarding is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpClassFwdingDefaultLsp 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.33
The value of sdpClassFwdingDefaultLsp specifies the LSP ID that is used as a default when class-based forwarding is enabled on this SDP. This object must be set when enabling class-based forwarding.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxVRtrMplsLspID  

sdpClassFwdingMcLsp 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.34
The value of sdpClassFwdingMcLsp specifies the LSP ID that all multicast traffic will be forwarded on when class-based forwarding is enabled on this SDP. When this object has its default value, multicast traffic will be forwarded on an LSP according to its forwarding class mapping.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxVRtrMplsLspID  

sdpMetric 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.35
The value of sdpMetric specifies the metric to be used within the Tunnel Table Manager for decision making purposes. When multiple SDPs going to the same destination exist, this value is used as a tie-breaker by Tunnel Table Manager users like MP-BGP to select route with lower value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

sdpAutoSdp 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.36
The value of sdpAutoSdp indicates whether this is an Auto generated SDP from RADIUS discovery or BGP auto-discovery.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpSnmpAllowed 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.37
The value of sdpSnmpAllowed indicates if SNMP sets are allowed on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpPBBEtype 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.38
This object specifies the Ethertype used in frames sent out on this SDP when sdpBindVcType is 'vlan' for Provider Backbone Bridging frames.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 600..ffff  

sdpBandwidthBookingFactor 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.39
sdpBandwidthBookingFactor is used to calculate the max SDP available bandwidth. The value of sdpBandwidthBookingFactor specifies the percentage of the SDP max available bandwidth for VLL call admission. When the value of sdpBandwidthBookingFactor is set to zero (0), no new VLL spoke-sdp bindings with non-zero bandwidth are permitted with this SDP. Overbooking, >100% is allowed.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1000  

sdpOperBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.40
The value of sdpOperBandwidth indicates the operational Bandwidth in kilo-bits per seconds (Kbps) available for this SDP. The value sdpOperBandwidth is determined by the sum of the bandwidth of all the RSVP LSPs used by the SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpAvailableBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.41
The value of sdpAvailableBandwidth indicates the Bandwidth that is still free for booking by the SDP bindings on the SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpMaxBookableBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.42
The value of sdpMaxBookableBandwidth indicates the max Bandwidth that the SDP has for booking by the SDP bindings. The value of sdpMaxBookableBandwidth is calculated as follow: sdpMaxBookableBandwidth = sdpOperBandwidth * sdpBandwidthBookingFactor
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

sdpBookedBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.43
The value of sdpBookedBandwidth indicates the SDP Bandwidth that has been booked by the SDP bindings.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

sdpCreationOrigin 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.44
The value of sdpCreationOrigin indicates the protocol or mechanism which created this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  L2RouteOrigin  

sdpEnforceDiffServLspFc 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.45
The value of sdpEnforceDiffServLspFc specifies whether service manager must validate with RSVP the support of the FC by the LSP. By default, the SDP uses the direct configuration without validation with RSVP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpMixedLspModeEnabled 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.46
The value of sdpMixedLspModeEnabled specifies whether mixed mode LSPs is enabled on this SDP. Setting the value to 'true' allows LDP to be enabled and LSPs to be configured at the same time on this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpLspRevertTime 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.47
The value of sdpLspRevertTime specifies the time to wait before reverting back from LDP to the configured LSPs, after having failed over to LDP. When the value is -1, the sdp will never revert back.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -1 | 0..600  

sdpLspRevertTimeCountDown 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.48
The value of sdpLspRevertTimeCountDown indicated the timer countdown before reverting back from LDP on this SDP. The timer countdown begins after the first configured LSP becomes active. The value of -1 indicates when the revert time countdown is not applicable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..600  

sdpLdpLspId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.49
The value of sdpLdpLspId indicates the Id for the LDP LSP if sdpLdpEnabled is set to 'true' and there is a valid LDP route to the sdpFarEndIpAddress or sdpFarEndNodeId.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpLdpActive 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.50
The value of sdpLdpActive indicates whether LDP is active for the current SDP.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpNetDomainName 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.51
The value of sdpNetDomainName specifies the network-domain name configured on this SDP. The dafault value of this object is the 'default' network-domain.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpEgressIfsNetDomainConsistent 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.52
The value of sdpEgressIfsNetDomainConsistent indicates whether all the egress network interfaces that can carry traffic on this SDP are associated with the network-domain configured on this SDP. A value of 'notApplicable' indicates that there is no egress network interface that can carry traffic on this SDP. A value of 'consistent' indicates that the network-domains for all the egress network interfaces that can carry traffic on this SDP are consistent. A value of 'inconsistent' indicates that the network-domain for one or more egress network interfaces that can carry traffic on this SDP are inconsistent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), consistent(2), inconsistent(3)  

sdpBgpTunnelEnabled 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.53
The value of sdpBgpTunnelEnabled specifies whether the transport tunnel is BGP as opposed to LDP or RSVP signalled LSPs. This value cannot be set to 'true' if sdpLdpEnabled is 'true' or if there is at least one RSVP or static LSP provisioned. This object applies to MPLS SDPs.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBgpTunnelLspId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.54
The value of sdpBgpTunnelLspId indicates the Id for the BGP Tunnel LSP if sdpBgpTunnelEnabled is set to 'true' and there is a valid LDP route to the sdpFarEndIpAddress.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpTunnelFarEndIpAddress 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.55
The value of sdpTunnelFarEndIpAddress specifies the IP address of the remote end of the tranport tunnel for this SDP. The value can only be changed while the admin status of the SDP is 'down'.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

sdpActiveLspType 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.56
The value of sdpActiveLspType indicates the type of LSP that is currently active on this SDP. For sdpDelivery 'gre', the value is always 'not-applicable'. For sdpDelivery 'mpls', the values can be 'rsvp', 'ldp', 'bgp' or 'none'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(0), rsvp(1), ldp(2), bgp(3), none(4)  

sdpBindingPort 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.57
The value of sdpBindingPort specifies the port id for the binding on this SDP. The value of sdpPwPortOperStatus will be set to 'down' of all the related SDP pseudo-wire ports, if the SDP resolves to another port than the one specified here. An 'inconsistentValue' error is returned when this object is set to a non-default value when sdpDelivery is set to 'gre'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxPortID  

sdpFarEndNodeId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.58
The value of sdpFarEndNodeId specifies the node identifier of the far-end for this sdp. The value of this object must be set to a non-default value when the sdpDelivery is set to 'mpls' for the row to become 'active', and can only be changed while the admin status of the SDP is 'down'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxMplsTpNodeID  

sdpFarEndGlobalId 1.3.6.1.4.1.6527.3.1.2.4.4.3.1.59
The value of sdpFarEndGlobalId specifies the global identifier of the far-end for this sdp.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxMplsTpGlobalID  

sdpBindTable 1.3.6.1.4.1.6527.3.1.2.4.4.4
A table that contains SDP binding information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindEntry

sdpBindEntry 1.3.6.1.4.1.6527.3.1.2.4.4.4.1
Information about a specific SDP binding.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindEntry  

sdpBindId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.1
SDP Binding identifier.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindId  

sdpBindRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.2
This object indicates the status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpBindAdminIngressLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.3
The static MPLS VC label used by the far-end device to send packets to this device in this service via this SDP. The value of sdpBindAdminIngressLabel is 1 when it is used by a mirror service. All mirror SDPs use this label to avoid the unnecessary use of additional labels.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 1 | 2048..18431  

sdpBindAdminEgressLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.4
The static MPLS VC label used by this device to send packets to the far-end device in this service via this SDP.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 16..1048575  

sdpBindOperIngressLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.5
The MPLS label used by the far-end device to send packets to this device in this service via this SDP. This label is either sdpBindAdminIngressLabel, if not null, or the one obtained via the SDP's signaling protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..1048575  

sdpBindOperEgressLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.6
The MPLS label used by this device to send packets to the far-end device in this service via this SDP. This label is either sdpBindAdminEgressLabel, if not null, or the one obtained via the SDP's signaling protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..1048575  

sdpBindAdminStatus 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.7
The desired state of this Service-SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  ServiceAdminStatus  

sdpBindOperStatus 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.8
The value of sdpBindOperStatus indicates the operating status of this Service-SDP binding. 'up' The Service-SDP binding is operational. 'noEgressLabel' The ingress label is available but the egress one is missing. 'noIngressLabel' The egress label is available but the ingress one is not. 'noLabels' Both the ingress and the egress labels are missing. 'down' The binding is administratively down. 'svcMtuMismatch' Both labels are available, but a service MTU mismatch was detected between the local and the far-end devices. 'sdpPathMtuTooSmall' The operating path MTU of the corresponding SDP minus the size of the SDP Bind control word (if applicable) is smaller than the service MTU. 'sdpNotReady' The SDP's signaling session is down. 'sdpDown' The SDP is not operationally up. 'sapDown' The SAP associated with the service is down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), noEgressLabel(2), noIngressLabel(3), noLabels(4), down(5), svcMtuMismatch(6), sdpPathMtuTooSmall(7), sdpNotReady(8), sdpDown(9), sapDown(10)  

sdpBindLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.9
The value of sysUpTime at the time of the most recent management-initiated change to this Service-SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindType 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.10
This object indicates whether this Service SDP binding is a spoke or a mesh. The value of this object must be specified when the row is created and cannot be changed while the row status is 'active'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER spoke(1), mesh(2)  

sdpBindIngressMacFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.11
The row index in the tMacFilterTable corresponding to this ingress filter, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindIngressIpFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.12
The row index in the tIPFilterTable corresponding to this ingress filter, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindEgressMacFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.13
The row index in the tMacFilterTable corresponding to this egress filter, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindEgressIpFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.14
The row index in the tIPFilterTable corresponding to this egress filter, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindVpnId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.15
The VPN ID of the associated service.
Status: current Access: read-only
OBJECT-TYPE    
  VpnId  

sdpBindCustId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.16
The Customer ID of the associated service.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxCustId  

sdpBindVcType 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.17
The value of sdpBindVcType is an enumerated integer that specifies the type of virtual circuit (VC) associated with the SDP binding. The value 'vpls' is no longer supported.
Status: current Access: read-create
OBJECT-TYPE    
  SdpBindVcType  

sdpBindVlanVcTag 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.18
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0000..0fff  

sdpBindSplitHorizonGrp 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.19
This value of the object sdpBindSplitHorizonGrp specifies the name of the split-horizon group where the spoke SDP Bind belongs to. This object can be set only at the time the row is created. Per default a spoke SDP Bind does not belong to any split-horizon group. The name specified must correspond to an existing split-horizon group in the TLS service where this spoke SDP Bind is defined.
Status: current Access: read-create
OBJECT-TYPE    
  ServObjName  

sdpBindOperFlags 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.20
This object specifies all the conditions that affect the operating status of this SDP Bind. The bit values are as follows: sdpBindAdminDown (0) - SDP Bind is admin down. svcAdminDown (1) - Service is admin down. sapOperDown (2) - SAP is oper down (VLL's only). sdpOperDown (3) - SDP is oper down. sdpPathMtuTooSmall (4) - SDP's path MTU minus SDP Bind control word size is less than Service MTU. noIngressVcLabel (5) - No ingress VC label. noEgressVcLabel (6) - No egress VC label. svcMtuMismatch (7) - Service MTU mismatch with the remote PE. vcTypeMismatch (8) - VC type mismatch with the remote PE. relearnLimitExceeded (9) - MAC relearn limit was exceeded (TLS only). iesIfAdminDown (10) - IP interface is admin down (IES and VPRN only). releasedIngressVcLabel (11) - Peer released our ingress VC label. labelsExhausted (12) - Label Manager has ran out of labels. svcParamMismatch (13) - Service-specific parameter mismatch. insufficientBandwidth (14) - Insufficient bandwidth to allocate to SDP binding. pwPeerFaultStatusBits (15) - Received PW fault status bits from peer. meshSdpDown (16) - Mesh SDP Down. notManagedByMcRing (17) - Not managed by mc-ring. outOfResource (18) - Such as memory. mhStandby (19) - Standby due to BGP. - multi-home protocol. oamDownMepFault (20) - ETH-CFM down MEP fault detected. oamUpMepFault (21) - ETH-CFM up MEP fault detected. standbySigSlaveTxDown (22) - Transmit is down for - standby-sig-spoke. operGrpDown (23) - Operational group is down. withdrawnIngressVcLabel(24) - Withdrawn due to Incompatiblity. vplsPmsiDown (25),- provider-tunnel down. recProtSrcMac (26) - Received a packet with a - protected source MAC. peerFaultStatusTxDown (27) - Transmit is down because - block-on-peer-fault is - enabled and received PW - faults status from peer
Status: current Access: read-only
OBJECT-TYPE    
  BITS sdpBindAdminDown(0), svcAdminDown(1), sapOperDown(2), sdpOperDown(3), sdpPathMtuTooSmall(4), noIngressVcLabel(5), noEgressVcLabel(6), svcMtuMismatch(7), vcTypeMismatch(8), relearnLimitExceeded(9), iesIfAdminDown(10), releasedIngressVcLabel(11), labelsExhausted(12), svcParamMismatch(13), insufficientBandwidth(14), pwPeerFaultStatusBits(15), meshSdpDown(16), notManagedByMcRing(17), outOfResource(18), mhStandby(19), oamDownMepFault(20), oamUpMepFault(21), standbySigSlaveTxDown(22), operGrpDown(23), withdrawnIngressVcLabel(24), vplsPmsiDown(25), recProtSrcMac(26), peerFaultStatusTxDown(27)  

sdpBindLastStatusChange 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.21
The value of the object sdpBindLastStatusChange specifies the value of sysUpTime at the time of the most recent operating status change to this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindIesIfIndex 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.22
When this SDP Bind is defined on an IES service and the value of sdpBindType is 'spoke', this object specifies the index of the associated IES interface. The value of this object can be set only when the row is created and cannot be changed while the row status is 'active'. This object is otherwise not significant and should have the value zero.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

sdpBindMacPinning 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.23
The value of the object sdpBindMacPinning specifies whether or not MAC address pinning is active on this SDP bind (mesh or spoke). Setting the value to enable disables re-learning of MAC addresses on other SAPs or SDPs within the same VPLS; the MAC address will hence remain attached to the SDP Bind for the duration of its age-timer. This object has effect only for MAC addresses learned via the normal MAC learning process, and not for entries learned via DHCP. The value will be set by default to disabled. However for a spoke SDP that belongs to a residential SHG, the value is set to enabled by the system, and cannot be altered by the operator. This object applies to spoke-SDP associated with the service with svcType set to 'tls'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindIngressIpv6FilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.24
The value of the object sdpBindIngressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this ingress ipv6 filter, or zero if no ipv6 filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindEgressIpv6FilterId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.25
The value of the object sdpBindEgressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this egress ipv6 filter, or zero if no ipv6 filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

sdpBindCollectAcctStats 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.26
The value of the object sdpBindCollectAcctStats specifies whether the agent collects accounting statistics for this SDP bind. When the value is 'true' the agent collects accounting statistics on this SDP bind.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindAccountingPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.27
The value of sdpBindAccountingPolicyId specifies the policy to use to collect accounting statistics on this SDP bind. The value zero indicates that the agent should use the default accounting policy, if one exists.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

sdpBindPwPeerStatusBits 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.28
sdpBindPwPeerStatusBits indicates the bits set by the LDP peer when there is a fault on its side of the pseudowire. LAC failures occur on the SAP that has been configured on the PIPE service, PSN bits are set by SDP-binding failures on the PIPE service. The pwNotForwarding bit is set when none of the above failures apply, such as an MTU mismatch failure. This value is only applicable if the peer is using the pseudowire status signalling method to indicate faults.
Status: current Access: read-only
OBJECT-TYPE    
  BITS pwNotForwarding(0), lacIngressFault(1), lacEgresssFault(2), psnIngressFault(3), psnEgressFault(4), pwFwdingStandby(5)  

sdpBindPeerVccvCvBits 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.29
sdpBindPeerVccvCvBits indicates the CV type bits set by the LDP peer if it supports VCCV (Virtual Circuit Connection Verification) on a pseudowire. If the peer does not send VCCV information, or does not support it, the bits will be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  BITS icmpPing(0), lspPing(1), bfdFaultDetection(2), bfdFaultDetectionAndSignalling(3)  

sdpBindPeerVccvCcBits 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.30
sdpBindPeerVccvCcBits indicates the CC type bits set by the LDP peer if it supports VCCV (Virtual Circuit Connection Verification) on a pseudowire. If the peer does not send VCCV information, or does not support it, the bits will all be 0.
Status: current Access: read-only
OBJECT-TYPE    
  BITS pwe3ControlWord(0), mplsRouterAlertLabel(1), mplsPwDemultiplexorLabel(2)  

sdpBindControlWordBit 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.31
sdpBindControlWordBit specifies whether the use of the 'ControlWord' is preferred or not. The value of sdpBindControlWordBit is exchanged with LDP peer during pseudowire negotiation time. The default value is determined by sdpBindVcType. sdpBindVcType of atmSdu and frDlci must have default value of 'true'. Other values of sdpBindVcType must have default value of 'false'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindOperControlWord 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.32
sdpBindOperControlWord indicates whether the 'ControlWord' is used or not. The value of sdpBindOperControlWord is negotiated with the LDP peer. When both the local and the peer prefer the use of the 'ControlWord', sdpBindOperControlWord has the value of 'true'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindEndPoint 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.33
sdpBindEndPoint specifies the service endpoint to which this SDP bind is attached. The svcId of the SDP bind MUST match the svcId of the service endpoint.
Status: current Access: read-create
OBJECT-TYPE    
  ServObjName  

sdpBindEndPointPrecedence 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.34
sdpBindEndPointPrecedence specifies the precedence of this SDP bind when there are multiple SDP binds attached to one service endpoint. The value 0 can only be assigned to one SDP bind, making it the primary SDP bind. When an SDP bind goes down, the next highest precedence SDP bind begins forwarding traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4  

sdpBindIsICB 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.35
sdpBindIsICB specifies whether this sdpBind is an inter-chassis backup SDP bind.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindPwFaultInetAddressType 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.36
The value of the object sdpBindPwFaultInetAddressType indicates the address type of sdpBindPwFaultInetAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

sdpBindPwFaultInetAddress 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.37
The value of sdpBindPwFaultInetAddress indicates the IP address that was included in the pseudowire status message sent by the LDP peer. This value is only applicable if the peer is using the pseudowire status signalling method to indicate faults.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

sdpBindClassFwdingOperState 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.38
The value of sdpBindClassFwdingOperState indicates the operational state of forwarding-class based forwarding on this sdpBind. When the SDP this sdpBind is bound to has sdpClassFwdingEnabled set to 'false', the value of sdpBindClassFwdingOperState is 'outOfService'. When the SDP this sdpBind is bound to has sdpClassFwdingEnabled set to 'true' and the svcType of the service this sdpBind is defined on is 'tls', 'vprn', or 'ies', the value of sdpBindClassFwdingOperState is 'inService'. If the service has svcVcSwitching set to 'true', the value of sdpBindClassFwdingOperState is 'inService' When the SDP this sdpBind is bound to has sdpClassFwdingEnabled set to 'true' and the svcType of the service this sdpBind is defined on is 'epipe', 'apipe', 'fpipe', or 'ipipe' with no SAP defined on the service, the value of sdpBindClassFwdingOperState is 'unknown'. If the service has a SAP with a NULL sapIngressSharedQueuePolicy, the value of sdpBindClassFwdingOperState is 'outOfService'. If the service has a SAP with a non-NULL sapIngressSharedQueuePolicy, the value of sdpBindClassFwdingOperState is 'inService'.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

sdpBindForceVlanVcForwarding 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.39
The value of sdpBindForceVlanVcForwarding specifies whether or not vc-vlan-type forwarding is forced in the data-path for the sdp which have sdpBindVcType set to 'ether'. When set to 'true' vc-vlan-type forwarding is forced. An 'inconsistentValue' error is returned when an attempt is made to set the value of sdpBindForceVlanVcForwarding to 'true' and sdpBindVcType is not set to 'ether'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindAdminBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.40
The value of the object sdpBindAdminBandwidth specifies the bandwidth that needs to be reserved for this SDP binding in kilo-bits per second. The SdpBindBandwidth object only applies to the SDP bindings under the epipe(1), apipe(7), fpipe(8), ipipe(9) and cpipe(10) services.
Status: current Access: read-create
OBJECT-TYPE    
  SdpBindBandwidth  

sdpBindOperBandwidth 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.41
The value of the object sdpBindOperBandwidth indicates the bandwidth that has been reserved for this SDP binding in kilo-bits per second. The value 0 indicates that SDP doesn't have bandwidth to satisfy the bandwidth requirement of this SDP binding. The sdpBindOperBandwidth object only applies to the SDP bindings under the epipe(1), apipe(7), fpipe(8), ipipe(9) and cpipe(10) services.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindBandwidth  

sdpBindCreationOrigin 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.42
The value of sdpBindCreationOrigin indicates the protocol or mechanism which created this SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  L2RouteOrigin  

sdpBindDescription 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.43
The value of sdpBindDescription specifies a user-provided description for the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

sdpBindSiteName 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.44
The value of sdpBindSiteName indicates the site-name associated with this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindHashLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.45
The value of sdpBindHashLabel specifies whether the use of hash-label is enabled or not on this SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindIsaAaApplicationProfile 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.46
The value of sdpBindIsaAaApplicationProfile specifies the ISA-AA application profile for this sdp. The specified application profile needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxAppProfTable.
Status: current Access: read-create
OBJECT-TYPE    
  ServObjName  

sdpBindStandbySigSlave 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.47
The value of sdpBindStandbySigSlave specifies whether transmission of the spoke will be blocked when the spoke receives standby status notification from its peer.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindHashLabelSignalCapability 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.48
The value of sdpBindHashLabel specifies whether to signal the hash label capability to the remote PE. The default value is 'false' and cannot be changed unless sdpBindHashLabel is set to 'true'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindIngressFlowspec 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.49
The value of sdpBindIngressFlowspec specifies whether ingress Flowspec is enabled for this sdp.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindCpmProtPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.50
The value of sdpBindCpmProtPolicyId specifies the CPM protection policy for this SDP binding. Zero specifies that no CPM protection policy is associated with this SDP binding. A non-zero value must be the index of an active tmnxCpmProtPolTable row. If the SDP binding can support Eth-CFM MEPs or MIPs, the default CPM protection policy is 255 (which is the default CPU protection policy for a network interface). Zero is not supported in this case. If the SDP binding cannot support Eth-CFM MEPs or MIPs, the default CPM protection policy is zero. Changing the CPM protection policy value is not supported in this case.
Status: current Access: read-create
OBJECT-TYPE    
  TCpmProtPolicyID  

sdpBindCpmProtMonitorMac 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.51
The value of sdpBindCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM protection policy (as specified by sdpBindCpmProtPolicyId) must be applied. If the value of sdpBindCpmProtMonitorMac is 'true', the per-source rate limit must be applied. If the value of sdpBindCpmProtPolicyId is zero, the value of sdpBindCpmProtMonitorMac is irrelevant and will be ignored. At most one of sdpBindCpmProtMonitorMac and the sdpBindCpmProtEthCfmMonitorFlags option 'ethCfmMonitor(0)' can be enabled for this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindCpmProtEthCfmMonitorFlags 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.52
The value of sdpBindCpmProtEthCfmMonitorFlags specifies whether or not to apply rate limiting (using the tmnxCpmProtEthCfmPolTable configuration) to Ethernet Connectivity Fault Management (Eth-CFM) packets served by the SDP binding. Two associated options are also specified. Five combinations of flag values are supported, as shown in the following table. Flag Value (0=Disabled, 1=Enabled) ------------------------------------- ----------------------------- 'ethCfmMonitor(0)' 0 0 0 0 1 1 1 1 'ethCfmMonitorAggregate(1)' 0 0 1 1 0 0 1 1 'ethCfmMonitorCommittedAccessRate(2)' 0 1 0 1 0 1 0 1 ------------------------------------- ----------------------------- Supported Combination? Y N N N Y Y Y Y If 'ethCfmMonitor(0)' is disabled, Eth-CFM rate limiting is disabled on this SDP binding. If 'ethCfmMonitor(0)' is enabled, Eth-CFM rate limiting is enabled on this SDP binding. Excess packets are discarded. The configured information used to perform the Eth-CFM rate limiting (e.g. the rate limit(s)) resides in the tmnxCpmProtEthCfmPolTable row(s) indexed by the SDP binding's sdpBindCpmProtPolicyId. At most one of 'ethCfmMonitor(0)' and sdpBindCpmProtMonitorMac can be enabled for this SDP binding. The flags 'ethCfmMonitorAggregate(1)' and 'ethCfmMonitorCommittedAccessRate(2)' adjust the behavior of Eth-CFM rate limiting. Therefore, they are only significant if Eth-CFM rate limiting is enabled (i.e. when 'ethCfmMonitor(0)' is enabled). The remainder of this DESCRIPTION assumes 'ethCfmMonitor(0)' is enabled. If 'ethCfmMonitorAggregate(1)' is disabled, the applicable Eth-CFM packet rate limit (tmnxCpmProtEthCfmPolRateLimit) applies per peer (i.e. on a source MAC address basis). For example, if the SDP binding's rate limit for all Eth-CFM packets is 100 packets/sec, and two peers are served by the SDP binding, then 100 Eth-CFM packets/sec from each peer is within the limit. If 'ethCfmMonitorAggregate(1)' is enabled, the applicable Eth-CFM packet rate limit (tmnxCpmProtEthCfmPolRateLimit) applies to the aggregated traffic flow. For example, if the SDP binding's rate limit for all Eth-CFM packets is 100 packets/sec, and two peers are served by this SDP binding, then the combined rate of the two peers cannot exceed 100 packets/sec. 'ethCfmMonitorCommittedAccessRate(2)' controls the interaction between two features: Eth-CFM rate limiting, and overall rate limiting (as configured using tmnxCpmProtPolOverallRateLimit). If 'ethCfmMonitorCommittedAccessRate(2)' is disabled, an Eth-CFM packet is subjected to two rate limits, in the following order. a) The applicable tmnxCpmProtEthCfmPolRateLimit is applied, as described above. If the packet exceeds the limit, it is discarded. Otherwise... b) The SDP binding's tmnxCpmProtPolOverallRateLimit (which is applied to Eth-CFM packets, and the other rate limited packet types) is applied. If 'ethCfmMonitorCommittedAccessRate(2)' is enabled, an Eth-CFM packet is subjected to one rate limit: the applicable tmnxCpmProtEthCfmPolRateLimit, as described above. Eth-CFM packets are neither counted nor discarded when performing the tmnxCpmProtPolOverallRateLimit rate limiting.
Status: current Access: read-create
OBJECT-TYPE    
  BITS ethCfmMonitor(0), ethCfmMonitorAggregate(1), ethCfmMonitorCommittedAccessRate(2)  

sdpBindTransitIpPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.53
The value of sdpBindTransitIpPolicyId specifies the transit IP policy to be associated with this SDP binding. The value must either be '0' indicating an invalid transit IP policy or the specified transit IP policy needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxTransitIpPolicyTable. At most one of sdpBindTransitIpPolicyId and sdpBindTransitPrefixPolicyId can be non-zero.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxBsxTransitIpPolicyIdOrZero  

sdpBindPwStatusSignaling 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.54
The value of sdpBindPwStatusSignaling specified whether this SDP binding supports pseudowire status signaling. Default value depends on the type of service: - For VPLS services it is 'true' and configurable. - For EPIPE services it is 'true' and configurable. - For all other VLL services it is 'true' but not configurable. - For Mirror services it is 'true' but not configurable. - For IES/VPRN services it is 'true' but not configurable. - For all other services it is 'false' and not configurable. An 'inconsistentValue' error is returned when an attempt is made to change this value for a SDP binding that is not configurable.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindOperGrp 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.55
The value of the sdpBindOperGrp specifies the Operational-Group identifier associated with this SDP Bind. An 'inconsistentValue' error is returned when both sdpBindOperGrp and sdpBindMonitorOperGrp are set together and atleast one of them to a non-default value.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindMonitorOperGrp 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.56
The value of the sdpBindMonitorOperGrp specifies the Operational-Group identifier which will affect the state of this SDP Bind. An 'inconsistentValue' error is returned when both sdpBindOperGrp and sdpBindMonitorOperGrp are set together and atleast one of them to a non-default value.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindOperHashLabel 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.57
The value of sdpBindOperHashLabel indicates the negotiated value of hash label that is used on this SDP binding. If the value of sdpBindHashLabel is set to 'true' but the value of sdpBindHashLabelSignalCapability is set to 'false' then sdpBindOperHashLabel will be 'true'. If the value of sdpBindHashLabelSignalCapability set to 'true' then the value of sdpBindOperHashLabel is 'true' if peer capability is 'true' and the 7xxx SR router hardware supports this capability. If the service has svcVcSwitching set to 'true', the value of sdpBindOperHashLabel will be 'true' if peer capability is 'true' and the 7xxx SR router hardware supports this capability.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindTransitPrefixPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.58
The value of sdpBindTransitPrefixPolicyId specifies the transit prefix policy to be associated with this SDP binding. The value must either be '0' indicating an invalid transit prefix policy or the specified transit prefix policy needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxTransPrefPolicyTable. At most one of sdpBindTransitIpPolicyId and sdpBindTransitPrefixPolicyId can be non-zero.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxBsxTransPrefPolicyIdOrZero  

sdpBindAarpId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.59
The value of sdpBindAarpId specifies the AA Redundancy Protocol (AARP) instance associated with this SDP binding. If set to 0, no AARP instance is associated with this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxBsxAarpIdOrZero  

sdpBindIngressQoSNetworkPlcyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.60
The value of the sdpBindIngressQoSNetworkPlcyId specifies the ingress QoS network policy applied to this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TSdpIngressPolicyID  

sdpBindEgressQoSNetworkPlcyId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.61
The value of the sdpBindEgressQoSNetworkPlcyId specifies the egress QoS network policy applied to this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TSdpEgressPolicyID  

sdpBindIngressQoSFpRedirectQGrp 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.62
The value of sdpBindIngressQoSFpRedirectQGrp specifies the forwarding-plane queue group Policy for this SDP binding. This object must be set along with sdpBindIngressQoSNetworkPlcyId object.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindEgressQoSPortRedirectQGrp 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.63
The value of sdpBindEgressQoSPortRedirectQGrp specifies the forwarding-plane queue group Policy for this SDP binding. This object must be set along with sdpBindEgressQoSNetworkPlcyId object.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindIngressQoSInstanceId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.64
The value of sdpBindIngressQoSInstanceId specifies the instance of the forwarding-plane ingress Queue Group for this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TQosQGrpInstanceIDorZero  

sdpBindEgressQoSInstanceId 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.65
The value of sdpBindEgressQoSInstanceId specifies the instance of the forwarding-plane egress Queue Group for this SDP binding.
Status: current Access: read-create
OBJECT-TYPE    
  TQosQGrpInstanceIDorZero  

sdpBindAarpServRefType 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.66
The value of sdpBindAarpServRefType specifies the role of the Spoke SDP referenced by the Redundancy Protocol (AARP) instance identified by sdpBindAarpId. If sdpBindAarpId is the invalid AARP instance '0', then the service reference type is 'none(0)'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxBsxAarpServiceRefType  

sdpBindPwLocalStatusBits 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.67
sdpBindPwLocalStatusBits indicates the bits set locally when there is a fault. LAC failures occur on the SAP that has been configured on the PIPE service, PSN bits are set by SDP-binding failures on the PIPE service. The pwNotForwarding bit is set when none of the above failures apply, such as an MTU mismatch failure. This value is sent to the peer via pseudowire status signalling method to indicate faults only if sdpBindPwStatusSignaling is set to true.
Status: current Access: read-only
OBJECT-TYPE    
  BITS pwNotForwarding(0), lacIngressFault(1), lacEgresssFault(2), psnIngressFault(3), psnEgressFault(4), pwFwdingStandby(5)  

sdpBindBlockOnPeerFault 1.3.6.1.4.1.6527.3.1.2.4.4.4.1.68
The sdpBindBlockOnPeerFault specifies whether to block the user traffic on this SDP bind when peer pw status has fault bits set.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindBaseStatsTable 1.3.6.1.4.1.6527.3.1.2.4.4.5
A table that contains basic SDP Binding statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindBaseStatsEntry

sdpBindBaseStatsEntry 1.3.6.1.4.1.6527.3.1.2.4.4.5.1
Basic statistics about a specific SDP Binding.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindBaseStatsEntry  

sdpBindBaseStatsIngressForwardedPackets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindBaseStatsIngressDroppedPackets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindBaseStatsEgressForwardedPackets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindBaseStatsEgressForwardedOctets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindBaseStatsCustId 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.5
The Customer ID of the associated service.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxCustId  

sdpBindBaseStatsIngFwdOctets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindBaseStatsIngDropOctets 1.3.6.1.4.1.6527.3.1.2.4.4.5.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

sdpBindTlsTable 1.3.6.1.4.1.6527.3.1.2.4.4.6
A table that contains TLS spoke SDP Bind information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindTlsEntry

sdpBindTlsEntry 1.3.6.1.4.1.6527.3.1.2.4.4.6.1
TLS specific information about an SDP Bind.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindTlsEntry  

sdpBindTlsStpAdminStatus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.1
The value of the object sdpBindTlsStpAdminStatus specifies whether this SDP Bind participates in the TLS's Spanning Tree Protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsStpPriority 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.2
The value of the object sdpBindTlsStpPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SDP Bind. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

sdpBindTlsStpPortNum 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.3
The value of the object sdpBindTlsStpPortNum specifies the value of the port number field which is contained in the least significant 12 bits of the 16-bit Port ID associated with this SDP Bind. Values in the range 2048..4094 are automatically assigned by the agent when the SDP Bind is created or when the value of this object is set to zero via management. Values in the range 1..2047 can be set via management, to allow this object to have a deterministic value across system reboots.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

sdpBindTlsStpPathCost 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.4
The value of the object sdpBindTlsStpPathCost specifies the contribution of this port to the path cost of paths towards the spanning tree root which include this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..200000000  

sdpBindTlsStpRapidStart 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.5
The value of the object sdpBindTlsStpRapidStart specifies whether Rapid Start is enabled on this SDP Bind. When the value is 'enabled' the Spanning Tree Protocol state transitions on this SDP Bind are driven by the value of the 'HelloTime', instead of the value of 'ForwardDelay', thus allowing a faster transition into the forwarding state.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsStpBpduEncap 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.6
The value of the object sdpBindTlsStpBpduEncap specifies the type of encapsulation used on BPDUs sent out and received on this SDP Bind.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(1), dot1d(2), pvst(3)  

sdpBindTlsStpPortState 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.7
The value of the object sdpBindTlsStpPortState indicates the port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the 'broken' state. All possible states are: learning, forwarding, broken, and discarding.
Status: current Access: read-only
OBJECT-TYPE    
  TStpPortState  

sdpBindTlsStpDesignatedBridge 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.8
The value of the object sdpBindTlsStpDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

sdpBindTlsStpDesignatedPort 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.9
The value of the object sdpBindTlsStpDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdpBindTlsStpForwardTransitions 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.10
The value of the object sdpBindTlsStpForwardTransitions indicates the number of times this port has transitioned from the Learning state to the Forwarding state.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpInConfigBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.11
The value of the object sdpBindTlsStpInConfigBpdus indicates the number of Configuration BPDUs received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpInTcnBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.12
The value of the object sdpBindTlsStpInTcnBpdus indicates the number of Topology Change Notification BPDUs received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpInBadBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.13
The value of the object sdpBindTlsStpInBadBpdus indicates the number of bad BPDUs received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpOutConfigBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.14
The value of the object sdpBindTlsStpOutConfigBpdus indicates the number of Configuration BPDUs sent out this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpOutTcnBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.15
The value of the object sdpBindTlsStpOutTcnBpdus indicates the number of Topology Change Notification BPDUs sent out this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpOperBpduEncap 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.16
The value of the object sdpBindTlsStpOperBpduEncap indicates the operating encapsulation type used on BPDUs sent out and received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot1d(2), pvst(3)  

sdpBindTlsStpVpnId 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.17
The value of the object sdpBindTlsStpVpnId indicates the VPN ID of the associated service.
Status: current Access: read-only
OBJECT-TYPE    
  VpnId  

sdpBindTlsStpCustId 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.18
The value of the object sdpBindTlsStpCustId indicates the Customer ID of the associated service.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxCustId  

sdpBindTlsMacAddressLimit 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.19
The value of the object sdpBindTlsMacAddressLimit specifies the maximum number of learned and static entries allowed in the FDB for this SDP Bind. The value 0 means: no limit for this SDP Bind. The command is valid only for spoke SDPs. The maximum value of sdpBindTlsMacAddressLimit is '511999', when the the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is 'd'. The maximum value of sdpBindTlsMacAddressLimit is '196607', when the the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is 'c'. In other cases, the maximum value of sdpBindTlsMacAddressLimit is '131071'.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..511999  

sdpBindTlsNumMacAddresses 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.20
The value of the object sdpBindTlsNumMacAddresses indicates the number of MAC addresses currently present in the FDB that belong to this SDP Bind (Both learned and static MAC addresses are counted).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdpBindTlsNumStaticMacAddresses 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.21
The value of the object sdpBindTlsNumStaticMacAddresses indicates the number of static MAC addresses currently present in the FDB that belong to this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdpBindTlsMacLearning 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.22
The value of the object sdpBindTlsMacLearning specifies whether the MAC learning process is enabled for this SDP Bind. The value is ignored if MAC learning is disabled on service level.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsMacAgeing 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.23
The value of the object sdpBindTlsMacAgeing specifies whether the MAC aging process is enabled for this SDP Bind. the value is ignored if MAC aging is disabled on service level.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsStpOperEdge 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.24
The value of the object sdpBindTlsStpOperEdge indicates the operational value of the Edge Port parameter. The object is initialized to the value of sdpBindTlsStpRapidStart and is set FALSE on reception of a BPDU.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindTlsStpAdminPointToPoint 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.25
The value of the object xx sdpBindTlsStpAdminPointToPoint specifies the administrative point-to-point status of the LAN segment attached to this sdp. A value of 'forceTrue' indicates that this port should always be treated as if it is connected to a point-to-point link. A value of 'forceFalse' indicates that this port should be treated as having a shared media connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1)  

sdpBindTlsStpPortRole 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.26
The value of the object sdpBindTlsStpPortRole indicates the current role of the sdp as defined by the Rapid Spanning Tree Protocol.
Status: current Access: read-only
OBJECT-TYPE    
  StpPortRole  

sdpBindTlsStpAutoEdge 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.27
The value of the object sdpBindTlsStpAutoEdge specifies whether this SDP is enabled for auto-edge detection as defined by Rapid Spanning Tree Protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsStpOperProtocol 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.28
The value of the object sdpBindTlsStpOperProtocol indicates whether stp, rstp or mstp is running on this spoke sdp. If the protocol is not enabled on this spoke-sdp the value notApplicable is returned.
Status: current Access: read-only
OBJECT-TYPE    
  StpProtocol  

sdpBindTlsStpInRstBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.29
The value of the object sdpBindTlsStpInRstBpdus indicates the number of Rapid Spanning Tree (Rst) BPDUs received on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpOutRstBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.30
The value of the object sdpBindTlsStpOutRstBpdus indicates the number of Rapid Spanning Tree (Rstp) BPDUs sent out on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsLimitMacMove 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.31
When sdpBindTlsLimitMacMove value is set to blockable (1) the agent will monitor the MAC relearn rate on this SDP Bind, and it will block it when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When the value is 'nonBlockable' this SDP binding will not be blocked, and another blockable SDP binding will be blocked instead.
Status: current Access: read-write
OBJECT-TYPE    
  TlsLimitMacMove  

sdpBindTlsDiscardUnknownSource 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.32
With the object sdpBindTlsMacAddressLimit a limit can be configured for the max number of MAC addresses that will be learned on this SDP Bind (only for spoke SDPs). When this limit is reached, packets with unknown source MAC address are forwarded by default. By setting sdpBindTlsDiscardUnknownSource to enabled, packets with unknown source MAC will be dropped in stead.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsMvplsPruneState 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.33
The value of the object sdpBindTlsMvplsPruneState indicates the mVPLS prune state of the spoke SDP. The object will be set to notApplicable if the spoke SDP is not managed by a mVPLS. If the SDP is managed the state reflects whether or not it is pruned by the STP instance running in the mVPLS instance.
Status: current Access: read-only
OBJECT-TYPE    
  MvplsPruneState  

sdpBindTlsMvplsMgmtService 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.34
The value of the object sdpBindTlsMvplsMgmtService indicates the service Id of the service where the STP instance is running that is managing this spoke SDP. This object is only valid if sdpBindTlsMvplsPruneState is different from notApplicable.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxServId  

sdpBindTlsMvplsMgmtSdpBndId 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.35
The value of the object sdpBindTlsMvplsMgmtSdpBndId indicates the SDP bind id in the mVPLS instance specified in sdpBindTlsMvplsMgmtService that is controlling this SDP. This object is only valid if sdpBindTlsMvplsPruneState is different from notApplicable.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindId  

sdpBindTlsStpException 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.36
The value of the object sdpBindTlsStpException indicates whether an STP exception condition is present on this Spoke Sdp. - none : no exception condition found. - oneWayCommuniation : The neighbor RSTP peer on this link is not able to detect our presence. - downstreamLoopDetected :A loop is detected on this link.
Status: current Access: read-only
OBJECT-TYPE    
  StpExceptionCondition  

sdpBindTlsL2ptTermination 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.37
The value of the object sdpBindTlsL2ptTermination specifies whether received L2 Protocol Tunnel pdu's are terminated on this port or sdp
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindTlsBpduTranslation 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.38
The value of the object sdpBindTlsBpduTranslation specifies whether received L2 Protocol Tunnel pdu's are translated before being sent out on this port or sap
Status: current Access: read-write
OBJECT-TYPE    
  TlsBpduTranslation  

sdpBindTlsStpRootGuard 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.39
The value of the object sdpBindTlsStpRootGuard specifies whether this port is allowed to become STP root port. It corresponds to the parameter 'restrictedRole' in 802.1Q. If set, it can cause lack of spanning tree connectivity.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindTlsStpInMstBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.40
The value of the object sdpBindTlsStpInMstBpdus indicates the number of Multiple Spanning Tree (Mst) BPDUs received on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpOutMstBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.41
The value of the object sdpBindTlsStpOutMstBpdus indicates the number of Multiple Spanning Tree (Mst) BPDUs sent out on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

sdpBindTlsStpRxdDesigBridge 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.42
The value of the object sdpBindTlsStpRxdDesigBridge indicates the designated Bridge Identifier in the last BPDU which was received on this SDP.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

sdpBindTlsMacMoveNextUpTime 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.43
The value of the object sdpBindTlsMacMoveNextUpTime counts down the time in seconds until a SDP bind that has been brought down due to exceeding the TLS svcTlsMacMoveMaxRate, sdpBindOperFlags 'relearnLimitExceeded', is automatically brought up again. When this value is 0xffff, the SDP bind will never be automatically brought up. When sdpBindOperStatus is 'up', this object counts down the time in seconds until the value of sdpBindTlsMacMoveRateExcdLeft is reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindTlsMacMoveRateExcdLeft 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.44
The value of the object sapTlsMacMoveRateExcdLeft counts down the number of times this SDP bind can exceed the TLS svcTlsMacMoveMaxRate and still be automatically brought up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindTlsLimitMacMoveLevel 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.45
The value of the object sdpBindTlsLimitMacMoveLevel specifies the hierarchy in which spoke-SDPs are blocked when a MAC-move limit is exceeded. When a MAC is moving among multiple SAPs or spoke-SDPs, the SAP bind or spoke-SDP bind with the lower level is blocked first. (tertiary is the lowest)
Status: current Access: read-write
OBJECT-TYPE    
  TlsLimitMacMoveLevel  

sdpBindTlsBpduTransOper 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.46
The value of the object sdpBindTlsBpduTransOper indicates the operational BPDU encapsulation used for BPDU translated frames.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), disabled(2), pvst(3), stp(4), pvst-rw(5)  

sdpBindTlsL2ptProtocols 4.1.3.6.1.4.1.6527.3.1.2.4.4.6.1.47
The value of the object sdpBindTlsL2ptProtocols specifies which L2 Protocol Tunnel pdu's are terminated on this port or sdp
Status: current Access: read-write
OBJECT-TYPE    
  L2ptProtocols  

sdpBindTlsIgnoreStandbySig 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.48
The value of sdpBindTlsIgnoreStandbySig specifies whether the local internal tasks will take into account the 'pseudo-wire forwarding standby' bit received from the LDP peer which is normally ignored. When set to 'true', this bit is not considered in the internal tasks. A similar object svcEndPointIgnoreStandbySig is present at the endpoint level. If this spoke-SDP is part of that explicit endpoint, this object will be set to the value of svcEndPointIgnoreStandbySig and its value will not allowed to be changed. This spoke-SDP can be made part of an explicit-endpoint only if the setting of this object is not conflicting with the setting of svcEndPointIgnoreStandbySig object.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindTlsBlockOnMeshFail 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.49
The value of sdpBindTlsBlockOnMeshFail specifies that the operational status of this spoke SDP will consider operational status of associated mesh SDPs in this service. If there are no mesh SDPs in the service, value of this object is ignored. When this object is set to 'true', then the operational status of this spoke SDP will be 'down' until the operational status of atleast one mesh SDP in this service is 'up'. When set to 'false', the operational status of this spoke SDP does not consider the operational status of any mesh SDPs in the service.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindTlsInTcBitBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.50
The value of the object sdpBindTlsInTcBitBpdus indicates the number BPDUs received on this SDP Bind with the Topology Change bit set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsOutTcBitBpdus 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.51
The value of the object sdpBindTlsOutTcBitBpdus indicates the number BPDUs sent out this SDP Bind with the Topology Change bit set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsRestProtSrcMac 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.52
The value of the object sdpBindTlsRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored. In addition, if the value of sdpBindTlsRestProtSrcMacAction is 'disable', then the SDP-BIND where the protected source MAC was seen will be brought operationally down.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindTlsRestProtSrcMacAction 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.53
The value of the object sdpBindTlsRestProtSrcMacAction indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is 'disable' the SAP will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarmOnly', the SDP-BIND will be left up and only a notification, sdpBindReceivedProtSrcMac, will be generated. When the value of this object is 'discardFrame', the SDP-BIND will start discarding the frame in addition to generating sdpBindReceivedProtSrcMac notification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), alarmOnly(2), discardFrame(3)  

sdpBindTlsAutoLearnMacProtect 1.3.6.1.4.1.6527.3.1.2.4.4.6.1.54
The value of sdpBindTlsAutoLearnMacProtect specifies whether to enable automatic population of the MAC protect list with source MAC addresses learned on the associated SDP binding.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindMeshTlsTable 1.3.6.1.4.1.6527.3.1.2.4.4.7
A table that contains TLS Mesh SDP Bind information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindMeshTlsEntry

sdpBindMeshTlsEntry 1.3.6.1.4.1.6527.3.1.2.4.4.7.1
TLS specific information about an Mesh SDP Bind.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindMeshTlsEntry  

sdpBindMeshTlsPortState 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.1
This object indicates the actual state of the Mesh SDP. If the sdp is operationally down, the port will be in the 'disabled' state. If the sdp is operationally up, the state will be 'forwarding' unless the hold-down timer is active in which case the state will be 'discarding'.
Status: current Access: read-only
OBJECT-TYPE    
  TStpPortState  

sdpBindMeshTlsHoldDownTimer 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.2
When the hold-down timer is active, all traffic coming from this mesh sdp will be blocked. This timer will be activated for any of the following cases: 1. when a mesh SDP becomes operational; 2. when a 'disputed' BPDU is received over this mesh sdp; This is typically a symptom of one way communication (the peer at the other side of the mesh sdp does not receive our BPDUs). 3. when a MSTP BPDU from outside the region is received over this mesh SDP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-active(1), active(2)  

sdpBindMeshTlsTransitionState 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.3
This object indicates whether we already received an agreement from the peer connected via this mesh sdp. RSTP expects an agreement from every peer after sending a proposal over the VCP when it wants to transition the latter to the forwarding state. This object is only relevant when the role of the VCP is 'designated'. Not receiving an agreement is typically caused by an improperly configured sdp or by a non rstp enabled peer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-applicable(1), waiting-for-agreement(2), agreement-received(3)  

sdpBindMeshTlsNotInMstRegion 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.4
This object sdpBindMeshTlsNotInMstRegion indicates whether we received a BPDU from another MST-region on this mesh SDP. If set to 'true' then the object sdpBindMeshTlsHoldDownTimer will have the value 'active'. It is up to the operator to make sure bridges connected via mesh SDPs are in the same MST-region. If not the mesh will NOT become operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindMeshTlsRestProtSrcMac 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.5
The value of the object sdpBindMeshTlsRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored. In addition, if the value of sdpBindMeshTlsRestProtSrcMacAct is 'disable', then the SDP-BIND where the protected source MAC was seen will be brought operationally down.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindMeshTlsRestProtSrcMacAct 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.6
The value of the object sdpBindMeshTlsRestProtSrcMacAct indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is 'disable' the SAP will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarmOnly', the SDP-BIND will be left up and only a notification, sdpBindReceivedProtSrcMac, will be generated. When the value of this object is 'discardFrame', the SDP-BIND will start discarding the frame in addition to generating sdpBindReceivedProtSrcMac notification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), alarmOnly(2), discardFrame(3)  

sdpBindMeshTlsAutoLearnMacProt 1.3.6.1.4.1.6527.3.1.2.4.4.7.1.7
The value of sdpBindMeshTlsAutoLearnMacProt specifies whether to enable automatic population of the MAC protect list with source MAC addresses learned on the associated SDP binding.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindApipeTable 1.3.6.1.4.1.6527.3.1.2.4.4.8
The sdpBindApipeTable has an entry for each apipe sdpBind configured on this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindApipeEntry

sdpBindApipeEntry 1.3.6.1.4.1.6527.3.1.2.4.4.8.1
Each row entry represents a particular sdpBind related to a particular Apipe service entry. Entries are created/deleted by the user.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindApipeEntry  

sdpBindApipeAdminConcatCellCount 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.1
The value of sdpBindApipeAdminConcatCellCount specifies the maximum number of ATM cells to accumulate into an MPLS packet. The remote peer will also signal the maximum number of concatenated cells it is willing to accept in an MPLS packet. When the lesser of (the configured value and the signaled value) number of cells is reached, the MPLS packet is queued for transmission onto the pseudowire.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..128  

sdpBindApipeSigConcatCellCount 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.2
The value of sdpBindApipeSigConcatCellCount indicates the maximum number of concatenated ATM cells the remote peer is willing to accept. If there is no remote peer, or if the label mapping has not been received, this object will be zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..128  

sdpBindApipeOperConcatCellCount 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.3
The value of sdpBindApipeOperConcatCellCount indicates the maximum number of concatenated ATM cells that will be sent on this SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..128  

sdpBindApipeConcatMaxDelay 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.4
The value of sdpBindApipeConcatMaxDelay object specifies the maximum amount of time to wait while performing ATM cell concatenation into an MPLS packet before transmitting the MPLS packet. This places an upper bound on the amount of delay introduced by the concatenation process. When this amount of time is reached from when the first ATM cell for this MPLS packet was received, the MPLS packet is queued for transmission onto the pseudowire.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..400  

sdpBindApipeConcatCellClp 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.5
The value of sdpBindApipeConcatCellClp specifies whether a CLP change should be used as an indication to complete the cell concatenation operation. When the value is 'true', CLP is used to indicate that cell concatenation should be completed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindApipeConcatCellAal5Fr 1.3.6.1.4.1.6527.3.1.2.4.4.8.1.6
The value of sdpBindApipeConcatCellAal5Fr specifies whether the AAL5 EOP (end of packet) should be used as an indication to complete the cell concatenation operation. When the value is 'true', EOP is used to indicate that cell concatenation should be completed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindDhcpInfoTable 1.3.6.1.4.1.6527.3.1.2.4.4.9
A table that contains DHCP information related to a SDP Bind. A row will exist in this table for each spoke or mesh SDP in a Tls Service. Rows are created and deleted automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindDhcpInfoEntry

sdpBindDhcpInfoEntry 1.3.6.1.4.1.6527.3.1.2.4.4.9.1
DHCP specific information about an SDP Bind.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindDhcpInfoEntry  

sdpBindDhcpDescription 1.3.6.1.4.1.6527.3.1.2.4.4.9.1.1
The value of the object sdpBindDhcpDescription specifies a user provided description for DHCP on this Sdp Bind.
Status: current Access: read-write
OBJECT-TYPE    
  ServObjDesc  

sdpBindDhcpSnoop 1.3.6.1.4.1.6527.3.1.2.4.4.9.1.2
The value of the object sdpBindDhcpSnoop specifies whether or not DHCP snooping is enabled on the Sdp Bind.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxEnabledDisabled  

sdpBindDhcpStatsTable 1.3.6.1.4.1.6527.3.1.2.4.4.10
sdpBindDhcpStatsTable contains DHCP statistics related to a TLS SDP Bind. A row will exist in this table for each spoke or mesh SDP in a Tls Service. Rows are created and deleted automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindDhcpStatsEntry

sdpBindDhcpStatsEntry 1.3.6.1.4.1.6527.3.1.2.4.4.10.1
DHCP statistics for a TLS spoke SDP or mesh SDP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindDhcpStatsEntry  

sdpBindDhcpStatsClntSnoopdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.1
The value of the object sdpBindDhcpStatsClntSnoopdPckts indicates the number of DHCP client packets that have been snooped on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsSrvrSnoopdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.2
The value of the object sdpBindDhcpStatsSrvrSnoopdPckts indicates the number of DHCP server packets that have been snooped on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsClntForwdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.3
The value of the object sdpBindDhcpStatsClntForwdPckts indicates the number of DHCP client packets that have been forwarded on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsSrvrForwdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.4
The value of the object sdpBindDhcpStatsSrvrForwdPckts indicates the number of DHCP server packets that have been forwarded on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsClntDropdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.5
The value of the object sdpBindDhcpStatsClntDropdPckts indicates the number of DHCP client packets that have been dropped on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsSrvrDropdPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.6
The value of the object sdpBindDhcpStatsSrvrDropdPckts indicates the number of DHCP server packets that have been dropped on this SDP bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsClntProxRadPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.7
The value of the object sdpBindDhcpStatsClntProxRadPckts indicates the number of DHCP client packets that have been proxied on this SDP bind based on data received from a RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsClntProxLSPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.8
The value of the object sdpBindDhcpStatsClntProxLSPckts indicates the number of DHCP client packets that have been proxied on this SDP bind based on a lease state. The lease itself can have been obtained from a DHCP or RADIUS server. This is the so called lease split functionality.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsGenReleasePckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.9
The value of the object sdpBindDhcpStatsGenReleasePckts indicates the number of DHCP RELEASE messages spoofed on this SDP bind to the DHCP server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindDhcpStatsGenForceRenPckts 1.3.6.1.4.1.6527.3.1.2.4.4.10.1.10
The value of the object sdpBindDhcpStatsGenForceRenPckts indicates the number of DHCP FORCERENEW messages spoofed on this SDP bind to the DHCP clients.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindIpipeTable 1.3.6.1.4.1.6527.3.1.2.4.4.11
The sdpBindIpipeTable has an entry for each IPIPE sdpBind configured on this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindIpipeEntry

sdpBindIpipeEntry 1.3.6.1.4.1.6527.3.1.2.4.4.11.1
Each row entry represents a particular sdpBind related to a particular IPIPE service entry. Entries are created/deleted by the user.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindIpipeEntry  

sdpBindIpipeCeInetAddressType 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.1
The value of the object sdpBindIpipeCeInetAddressType specifies the address type of the IP address of the CE device reachable throught this IPIPE SDP binding. This object is only configurable if the value of 'svcIpipeCeAddressDiscovery' is 'disabled.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

sdpBindIpipeCeInetAddress 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.2
The type of this address is determined by the value of the sdpBindIpipeCeInetAddressType object. This object specifies the IPv4 address of the CE device reachable through this SDP binding. This object is only configurable if the value of 'svcIpipeCeAddressDiscovery' is 'disabled.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress Size(0|4)  

sdpBindIpipePeerCeInetAddrType 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.3
If the value of 'svcIpipeCeAddressDiscovery' is enabled, the value of the object sdpBindIpipeCeInetAddressType indicates the address type of the IP address of the CE device that is learnt via LDP on this IPIPE SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

sdpBindIpipePeerCeInetAddr 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.4
If the value of 'svcIpipeCeAddressDiscovery' is enabled, the type of this address is determined by the value of the sdpBindIpipeCeInetAddressType object. This object indicates the IPv4 address of the CE device that is learnt via LDP on this SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

sdpBindIpipePeerIpv6Capability 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.5
The value of sdpBindIpipePeerIpv6Capability indicates whether the far end sent us the IPv6 Stack capability TLV.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindIpipePeerLLCeInetAddr 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.6
If the value of svcIpipeIpv6CeAddressDiscovery is 'enabled (1)', this object indicates the discovered link local IPv6 address of the far end CE device that is learnt via NS/NA messages received on this SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

sdpBindIpipePeerGlobalCeInetAddr 1.3.6.1.4.1.6527.3.1.2.4.4.11.1.7
If the value of svcIpipeIpv6CeAddressDiscovery is 'enabled (1)', this object indicates the discovered global IPv6 address of the far end CE device that is learnt via NS/NA messages received on this SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

sdpFCMappingTable 1.3.6.1.4.1.6527.3.1.2.4.4.12
The sdpFCMappingTable has an entry for each FC mapping on an SDP configured on this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpFCMappingEntry

sdpFCMappingEntry 1.3.6.1.4.1.6527.3.1.2.4.4.12.1
Each row entry represents a particular FC to LSP ID mapping on an SDP. Entries are created/deleted by the user.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpFCMappingEntry  

sdpFCMappingFCName 1.3.6.1.4.1.6527.3.1.2.4.4.12.1.1
The value of sdpFCMappingFCName specifies the forwarding class for which this mapping is defined, in the SDP indexed by 'sdpId'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TNamedItem  

sdpFCMappingRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.12.1.2
The value of sdpFCMappingRowStatus is used for the creation and deletion of forwarding class to LSP mappings.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpFCMappingLspId 1.3.6.1.4.1.6527.3.1.2.4.4.12.1.3
The value of sdpFCMappingLspId specifies the LSP ID that traffic corresponding to the class specified in sdpFCMappingFCName will be forwarded on. This object MUST be specified at row creation time.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxVRtrMplsLspID  

sdpBindCpipeTable 1.3.6.1.4.1.6527.3.1.2.4.4.15
The sdpBindCpipeTable has an entry for each cpipe sdpBind configured on this system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindCpipeEntry

sdpBindCpipeEntry 1.3.6.1.4.1.6527.3.1.2.4.4.15.1
Each row entry represents a particular sdpBind related to a particular Cpipe service entry. Entries are created/deleted by the user.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindCpipeEntry  

sdpBindCpipeLocalPayloadSize 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.1
This object indicates the local payload size (in bytes).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindCpipePeerPayloadSize 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.2
This object indicates the remote payload size (in bytes). If there is no remote peer, or if the label mapping has not been received, or if this value has not been received from the remote peer then this object will be zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindCpipeLocalBitrate 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.3
This object indicates the local bit-rate in multiples of 64 Kbit/s.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindCpipePeerBitrate 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.4
This object indicates the remote bit-rate in multiples of 64 Kbit/s. If there is no remote peer, or if the label mapping has not been received, or if this value has not been received from the remote peer then this object will be zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindCpipeLocalSigPkts 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.5
This object indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

sdpBindCpipePeerSigPkts 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.6
This object indicates the remote CE application signalling packets mode. If there is no remote peer, or if the label mapping has not been received, or if the remote peer does not support signalling packets then this object will be zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

sdpBindCpipeLocalCasTrunkFraming 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.7
This object indicates the local CAS trunk framing mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

sdpBindCpipePeerCasTrunkFraming 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.8
This object indicates the remote CAS trunk framing mode. If there is no remote peer, or if the label mapping has not been received, or if the remote peer does not support CAS trunk framing then this object will be zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

sdpBindCpipeLocalUseRtpHeader 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.9
This object indicates whether a RTP header is used when packets are transmitted to the remote peer, and the local peer expects a RTP header when packets are received from the remote peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindCpipePeerUseRtpHeader 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.10
This object indicates whether a RTP header is used when packets are transmitted by the remote peer, and the remote peer expects a RTP header when packets are received from the local peer. If there is no remote peer, or if the label mapping has not been received, or if the remote peer does not support RTP headers then this object will be 'false'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindCpipeLocalDifferential 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.11
This object indicates whether differential timestamp mode is used in the RTP header when packets are transmitted to the remote peer, and the local peer expects differential timestamps in the RTP header when packets are received from the remote peer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindCpipePeerDifferential 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.12
This object indicates whether differential timestamp mode is used in the RTP header when packets are transmitted by the remote peer, and the remote peer expects differential timestamps in the RTP header when packets are received from the local peer. If there is no remote peer, or if the label mapping has not been received, or if the remote peer does not support differential timestamp mode then this object will be 'false'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindCpipeLocalTimestampFreq 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.13
This object indicates the timestamp frequency used in the RTP header when packets are transmitted to the remote peer, and the local peer expects same timestamp frequency in the RTP header when packets are received from the remote peer. This value is in multiples of 8 KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindCpipePeerTimestampFreq 1.3.6.1.4.1.6527.3.1.2.4.4.15.1.14
This object indicates the timestamp frequency used in the RTP header when packets are transmitted by the remote peer, and the remote peer expects the same timestamp frequency in the RTP header when packets are received from the local peer. If there is no remote peer, or if the label mapping has not been received, or if the remote peer does not support support RTP headers then this object will be zero (0). This value is in multiples of 8 KHz.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpBindTlsMfibAllowedMdaTable 1.3.6.1.4.1.6527.3.1.2.4.4.13
The sdpBindTlsMfibAllowedMdaTable has an entry for each MFIB allowed MDA destination for an SDP Binding configured in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindTlsMfibAllowedMdaEntry

sdpBindTlsMfibAllowedMdaEntry 1.3.6.1.4.1.6527.3.1.2.4.4.13.1
Each row entry represents an MFIB allowed MDA destination for an SDP Binding configured in the system. Entries can be created and deleted via SNMP SET operations on the object sdpBindTlsMfibMdaRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindTlsMfibAllowedMdaEntry  

sdpBindTlsMfibMdaRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.13.1.1
The value of sdpBindTlsMfibMdaRowStatus controls the creation and deletion of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpBindTlsL2ptStatsTable 1.3.6.1.4.1.6527.3.1.2.4.4.16
A table that contains TLS spoke SDP Bind Layer 2 Protocol Tunneling Statistics. This table complements the sdpBindTlsTable. Rows in this table are created and deleted automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindTlsL2ptStatsEntry

sdpBindTlsL2ptStatsEntry 1.3.6.1.4.1.6527.3.1.2.4.4.16.1
TLS specific information about an SDP Bind.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindTlsL2ptStatsEntry  

sdpBindTlsL2ptStatsLastClearedTime 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.1
The value of sdpBindTlsL2ptStatsLastClearedTime indicates the last time that these stats were cleared. The value zero indicates that they have not been cleared yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.2
The value of sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusRx indicates the number of L2PT encapsulated STP config bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.3
The value of sdpBindTlsL2ptStatsL2ptEncapStpConfigBpdusTx indicates the number of L2PT encapsulated STP config bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.4
The value of sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusRx indicates the number of L2PT encapsulated STP rst bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.5
The value of sdpBindTlsL2ptStatsL2ptEncapStpRstBpdusTx indicates the number of L2PT encapsulated STP rst bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.6
The value of sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusRx indicates the number of L2PT encapsulated STP tcn bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.7
The value of sdpBindTlsL2ptStatsL2ptEncapStpTcnBpdusTx indicates the number of L2PT encapsulated STP tcn bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.8
The value of sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusRx indicates the number of L2PT encapsulated PVST config bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.9
The value of sdpBindTlsL2ptStatsL2ptEncapPvstConfigBpdusTx indicates the number of L2PT encapsulated PVST config bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.10
The value of sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusRx indicates the number of L2PT encapsulated PVST rst bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.11
The value of sdpBindTlsL2ptStatsL2ptEncapPvstRstBpdusTx indicates the number of L2PT encapsulated PVST rst bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.12
The value of sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusRx indicates the number of L2PT encapsulated PVST tcn bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.13
The value of sdpBindTlsL2ptStatsL2ptEncapPvstTcnBpdusTx indicates the number of L2PT encapsulated PVST tcn bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpConfigBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.14
The value of sdpBindTlsL2ptStatsStpConfigBpdusRx indicates the number of STP config bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpConfigBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.15
The value of sdpBindTlsL2ptStatsStpConfigBpdusTx indicates the number of STP config bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpRstBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.16
The value of sdpBindTlsL2ptStatsStpRstBpdusRx indicates the number of STP rst bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpRstBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.17
The value of sdpBindTlsL2ptStatsStpRstBpdusTx indicates the number of STP rst bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpTcnBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.18
The value of sdpBindTlsL2ptStatsStpTcnBpdusRx indicates the number of STP tcn bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsStpTcnBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.19
The value of sdpBindTlsL2ptStatsStpTcnBpdusTx indicates the number of STP tcn bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstConfigBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.20
The value of sdpBindTlsL2ptStatsPvstConfigBpdusRx indicates the number of PVST config bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstConfigBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.21
The value of sdpBindTlsL2ptStatsPvstConfigBpdusTx indicates the number of PVST config bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstRstBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.22
The value of sdpBindTlsL2ptStatsPvstRstBpdusRx indicates the number of PVST rst bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstRstBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.23
The value of sdpBindTlsL2ptStatsPvstRstBpdusTx indicates the number of PVST rst bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstTcnBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.24
The value of sdpBindTlsL2ptStatsPvstTcnBpdusRx indicates the number of PVST tcn bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPvstTcnBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.25
The value of sdpBindTlsL2ptStatsPvstTcnBpdusTx indicates the number of PVST tcn bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.26
The value of sdpBindTlsL2ptStatsOtherBpdusRx indicates the number of other bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.27
The value of sdpBindTlsL2ptStatsOtherBpdusTx indicates the number of other bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherL2ptBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.28
The value of sdpBindTlsL2ptStatsOtherL2ptBpdusRx indicates the number of other L2PT bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherL2ptBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.29
The value of sdpBindTlsL2ptStatsOtherL2ptBpdusTx indicates the number of other L2PT bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherInvalidBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.30
The value of sdpBindTlsL2ptStatsOtherInvalidBpdusRx indicates the number of other invalid bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsOtherInvalidBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.31
The value of sdpBindTlsL2ptStatsOtherInvalidBpdusTx indicates the number of other invalid bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapCdpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.32
The value of sdpBindTlsL2ptStatsL2ptEncapCdpBpdusRx indicates the number of L2PT encapsulated CDP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapCdpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.33
The value of sdpBindTlsL2ptStatsL2ptEncapCdpBpdusTx indicates the number of L2PT encapsulated CDP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapVtpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.34
The value of sdpBindTlsL2ptStatsL2ptEncapVtpBpdusRx indicates the number of L2PT encapsulated VTP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapVtpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.35
The value of sdpBindTlsL2ptStatsL2ptEncapVtpBpdusTx indicates the number of L2PT encapsulated VTP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapDtpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.36
The value of sdpBindTlsL2ptStatsL2ptEncapDtpBpdusRx indicates the number of L2PT encapsulated DTP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapDtpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.37
The value of sdpBindTlsL2ptStatsL2ptEncapDtpBpdusTx indicates the number of L2PT encapsulated DTP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPagpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.38
The value of sdpBindTlsL2ptStatsL2ptEncapPagpBpdusRx indicates the number of L2PT encapsulated PAGP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapPagpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.39
The value of sdpBindTlsL2ptStatsL2ptEncapPagpBpdusTx indicates the number of L2PT encapsulated PAGP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapUdldBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.40
The value of sdpBindTlsL2ptStatsL2ptEncapUdldBpdusRx indicates the number of L2PT encapsulated UDLD bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsL2ptEncapUdldBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.41
The value of sdpBindTlsL2ptStatsL2ptEncapUdldBpdusTx indicates the number of L2PT encapsulated UDLD bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsCdpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.42
The value of sdpBindTlsL2ptStatsCdpBpdusRx indicates the number of CDP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsCdpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.43
The value of sdpBindTlsL2ptStatsCdpBpdusTx indicates the number of CDP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsVtpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.44
The value of sdpBindTlsL2ptStatsVtpBpdusRx indicates the number of VTP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsVtpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.45
The value of sdpBindTlsL2ptStatsVtpBpdusTx indicates the number of VTP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsDtpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.46
The value of sdpBindTlsL2ptStatsDtpBpdusRx indicates the number of DTP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsDtpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.47
The value of sdpBindTlsL2ptStatsDtpBpdusTx indicates the number of DTP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPagpBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.48
The value of sdpBindTlsL2ptStatsPagpBpdusRx indicates the number of PAGP bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsPagpBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.49
The value of sdpBindTlsL2ptStatsPagpBpdusTx indicates the number of PAGP bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsUdldBpdusRx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.50
The value of sdpBindTlsL2ptStatsUdldBpdusRx indicates the number of UDLD bpdus received on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsL2ptStatsUdldBpdusTx 1.3.6.1.4.1.6527.3.1.2.4.4.16.1.51
The value of sdpBindTlsL2ptStatsUdldBpdusTx indicates the number of UDLD bpdus transmitted on this spoke SDP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwTemplateTableLastChanged 1.3.6.1.4.1.6527.3.1.2.4.4.17
The value of pwTemplateTableLastChanged indicates the sysUpTime at the time of the last modification of pwTemplateTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwTemplateTable 1.3.6.1.4.1.6527.3.1.2.4.4.18
A table that contains entries for pseudowire (PW) templates specifying SDP auto-binding.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwTemplateEntry

pwTemplateEntry 1.3.6.1.4.1.6527.3.1.2.4.4.18.1
Information about a specific PW template.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwTemplateEntry  

pwTemplateId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.1
The PW template identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  PWTemplateId  

pwTemplateRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.2
The value of pwTemplateRowStatus is used for the creation and deletion of PW templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwTemplateLastChanged 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.3
The value of pwTemplateLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwTemplateUseProvisionedSdp 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.4
The value of pwTemplateUseProvisionedSdp specifies whether the to use an already provisioned SDP. A value of 'true' specifies that the tunnel manager will be consulted for an existing active SDP. Otherwise, a value of 'false' specifies that the default SDP template will be used to use for instantiation of the SDP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateVcType 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.5
The value of pwTemplateVcType specifies the type of virtual circuit (VC) associated with the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  SdpBindVcType  

pwTemplateAccountingPolicyId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.6
The value of pwTemplateAccountingPolicyId specifies the policy to use to collect accounting statistics on the SDP Bind. The value zero indicates that the agent should use the default accounting policy, if one exists.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

pwTemplateCollectAcctStats 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.7
The value of pwTemplateCollectAcctStats specifies whether the agent collects accounting statistics for the SDP Bind. When the value is 'true' the agent collects accounting statistics on the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateMacLearning 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.8
The value of pwTemplateMacLearning specifies whether the MAC learning process is enabled for the SDP Bind. The value is ignored if MAC learning is disabled at service level.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateMacAgeing 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.9
The value of pwTemplateMacAgeing specifies whether the MAC aging process is enabled for the SDP Bind. The value is ignored if MAC aging is disabled at the service level.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateDiscardUnknownSource 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.10
With the object pwTemplateMacAddressLimit a limit can be configured for the max number of MAC addresses that will be learned on the SDP Bind (only for spoke SDPs). When the limit is reached, packets with unknown source MAC address are forwarded by default. By setting sdpBindTlsDiscardUnknownSource to 'enabled', packets with unknown source MAC will be dropped instead.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateLimitMacMove 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.11
The value of pwTemplateLimitMacMove specifies the behavior for when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When pwTemplateLimitMacMove value is set to 'blockable' the agent will monitor the MAC relearn rate on the SDP Bind, and it will block it when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When the value is 'nonBlockable' the SDP Bind will not be blocked, and another blockable SDP Bind will be blocked instead.
Status: current Access: read-create
OBJECT-TYPE    
  TlsLimitMacMove  

pwTemplateMacPinning 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.12
The value of pwTemplateMacPinning specifies whether or not MAC address pinning is active on the SDP Bind (mesh or spoke). Setting the value to 'enabled' disables re-learning of MAC addresses on other SAPs or SDPs within the same VPLS; the MAC address will hence remain attached to the SDP Bind for the duration of its age-timer. This object has effect only for MAC addresses learned via the normal MAC learning process, and not for entries learned via DHCP. The value will be set by default to 'disabled'. However for a spoke SDP that belongs to a residential SHG, the value is set to enabled by the system, and cannot be altered by the operator.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateVlanVcTag 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.13
The value of pwTemplateVlanVcTag specifies the VLAN VC tag for the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0000..0fff  

pwTemplateMacAddressLimit 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.14
The value of pwTemplateMacAddressLimit specifies the maximum number of learned and static entries allowed in the FDB for the SDP Bind. The value 0 specifies no limit for the SDP Bind. The command is valid only for spoke SDPs. When the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is 'a' or 'b', the maximum value of this object is '131071'. When the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is 'c', the maximum value of this object is '196607'. When the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is 'd', the maximum value of this object is '524287'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..524287  

pwTemplateShgName 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.15
The value of pwTemplateShgName specifies the name of the split-horizon group where the spoke SDP Bind belongs to. By default a spoke SDP Bind does not belong to any split-horizon group. The name specified must correspond to an existing split-horizon group in the TLS service where the spoke SDP Bind is defined.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

pwTemplateShgDescription 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.16
The value of pwTemplateShgDescription specifies a user-provided description for split-horizon group on the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

pwTemplateShgRestProtSrcMac 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.17
The value of pwTemplateShgRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateShgRestUnprotDstMac 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.18
The value of pwTemplateShgRestUnprotDstMac specifies how the system will forward packets destined to an unprotected MAC address. When the value of this object is 'true' packets destined to an unprotected MAC address will be dropped.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateEgressMacFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.19
The value of pwTemplateEgressMacFilterId specifies the tMacFilterId which indexes an egress filter entry in TIMETRA-FILTER-MIB::tMacFilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateEgressIpFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.20
The value of pwTemplateEgressIpFilterId specifies the tIPFilterId which indexes an egress filter entry in TIMETRA-FILTER-MIB::tIPFilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateEgressIpv6FilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.21
The value of pwTemplateEgressIpv6FilterId specifies the tIPv6FilterId which indexes an egress filter entry in TIMETRA-FILTER-MIB::tIPv6FilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateIngressMacFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.22
The value of pwTemplateIngressMacFilterId specifies the tMacFilterId which indexes an ingress filter entry in TIMETRA-FILTER-MIB::tMacFilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateIngressIpFilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.23
The value of pwTemplateIngressIpFilterId specifies the tIPFilterId which indexes an ingress filter entry in TIMETRA-FILTER-MIB::tIPFilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateIngressIpv6FilterId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.24
The value of pwTemplateIngressIpv6FilterId specifies the tIPv6FilterId which indexes an ingress filter entry in TIMETRA-FILTER-MIB::tIPv6FilterTable, or zero if no filter is specified.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterID  

pwTemplateIgmpFastLeave 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.25
The value of pwTemplateIgmpFastLeave specifies whether or not fastleave is allowed on the SDP Bind. If set to 'enabled', the system prunes the port on which an IGMP 'leave' message has been received without waiting for the Group Specific Query to timeout.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateIgmpImportPlcy 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.26
The value of pwTemplateIgmpImportPlcy specifies a policy statement that must be applied to all incoming IGMP messages on the SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

pwTemplateIgmpLastMembIntvl 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.27
The value of pwTemplateIgmpLastMembIntvl specifies the Max Response Time (in tenths of a second) used in Group-Specific and Group-Source-Specific Queries sent in response to 'leave' messages. This is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..50  

pwTemplateIgmpMaxNbrGrps 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.28
The value of pwTemplateIgmpMaxNbrGrps specifies how many group addresses are allowed for the SDP Bind. The value 0 means that no limit is imposed.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1000  

pwTemplateIgmpGenQueryIntvl 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.29
The value of pwTemplateIgmpGenQueryIntvl specifies the interval (in seconds) between two consecutive general queries sent by the system on the SDP. The value of this object is only meaningful when the value of pwTemplateIgmpSendQueries is 'enabled'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..1024  

pwTemplateIgmpQueryRespIntvl 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.30
The value of pwTemplateIgmpQueryRespIntvl specifies the maximum response time (in seconds) advertised in IGMPv2/v3 queries. The value of this object is only meaningful when the value of pwTemplateIgmpSendQueries is 'enabled'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..1023  

pwTemplateIgmpRobustCount 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.31
The value of pwTemplateIgmpRobustCount specifies the value of the Robust count. This object allows tuning for the expected packet loss on the SDP. If an SDP is expected to be lossy, the Robustness Variable may be increased. IGMP snooping is robust to (Robustness Variable-1) packet losses. The value of this object is only meaningful when the value of pwTemplateIgmpSendQueries is 'enabled'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..7  

pwTemplateIgmpSendQueries 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.32
The value of pwTemplateIgmpSendQueries specifies whether the system generates General Queries by itself on the SDP.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

pwTemplateIgmpMcacPolicyName 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.33
The value of pwTemplateIgmpMcacPolicyName indicates the name of the multicast CAC policy.
Status: obsolete Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

pwTemplateIgmpMcacUnconstBW 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.34
The value of pwTemplateIgmpMcacUnconstBW specifies the bandwidth assigned for interface's multicast CAC policy traffic in kilo-bits per second(kbps). If the default value of '-1' is set, there is no constraint on bandwidth allocated at the interface. If the value of pwTemplateIgmpMcacUnconstBW is set to '0' and if a multicast CAC policy is assigned on the interface, then no group (channel) from that policy is allowed on that interface.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 -1 | 0..2147483647  

pwTemplateIgmpMcacPrRsvMndBW 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.35
The value of pwTemplateIgmpMcacPrRsvMndBW specifies the bandwidth pre-reserved for all the mandatory channels on a given interface in kilo-bits per second(kbps). If the value of pwTemplateIgmpMcacUnconstBW is '0', no mandatory channels are allowed. If the value of pwTemplateIgmpMcacUnconstBW is '-1', then all mandatory and optional channels are allowed. If the value of pwTemplateIgmpMcacPrRsvMndBW is equal to the value of pwTemplateIgmpMcacUnconstBW, then all the unconstrained bandwidth on a given interface is allocated to mandatory channels configured through multicast CAC policy on that interface and no optional groups (channels) are allowed. The value of pwTemplateIgmpMcacPrRsvMndBW should always be less than or equal to that of pwTemplateIgmpMcacUnconstBW. An attempt to set the value of pwTemplateIgmpMcacPrRsvMndBW greater than that of pwTemplateIgmpMcacUnconstBW will result in 'inconsistentValue' error.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 -1 | 0..2147483647  

pwTemplateIgmpVersion 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.36
The value of pwTemplateIgmpVersion specifies the version of IGMP for the PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxIgmpVersion  

pwTemplateForceVlanVcForwarding 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.37
The value of pwTemplateForceVlanVcForwarding specifies whether or not vc-vlan-type forwarding is forced in the data-path when pwTemplateVcType is set to 'ether'. When pwTemplateForceVlanVcForwarding is set to 'true', vc-vlan-type forwarding is forced. An 'inconsistentValue' error is returned when an attempt is made to set the value of pwTemplateForceVlanVcForwarding to 'true' and pwTemplateVcType is not set to 'ether'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateHashLabel 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.38
The value of pwTemplateHashLabel specifies whether the use of hash-label is enabled or not for the PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateControlWord 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.39
The value of pwTemplateControlWord specifies whether the use of 'ControlWord' is enabled on pseudowire packets or not. When the value of the object is set to 'true', all VPLS packets are encapsulated with the control word when sent over the pseudowire. When the value of the object is set to 'false', the use of 'ControlWord' is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateHashLabelSignalCap 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.40
The value of pwTemplateHashLabelSignalCap specifies whether to signal the hash label capability to the remote PE. The default value is 'false' and cannot be changed unless pwTemplateHashLabel is set to 'true'.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateRestProtSrcMac 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.52
The value of the object pwTemplateRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is 'true' requests to relearn a protected MAC address will be ignored. In addition, if the value of pwTemplateRestProtSrcMacAction is 'disable', then the SAP or SDP-BIND where the protected source MAC was seen will be brought operationally down.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateRestProtSrcMacAction 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.53
The value of the object pwTemplateRestProtSrcMacAction indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is 'disable' the SAP will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarmOnly', the SAP or SDP-BIND which sets the restricted MAC will be left up and only a notification, sapReceivedProtSrcMac or sdpBindReceivedProtSrcMac, will be generated. When the value of this object is 'discardFrame', the SAP or SDP-BIND which sees the restricted MAC will start discarding the frame in addition to generating sapReceivedProtSrcMac or sdpBindReceivedProtSrcMac notification.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), alarmOnly(2), discardFrame(3)  

pwTemplateAutoLearnMacProtect 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.54
The value of pwTemplateAutoLearnMacProtect specifies whether to enable automatic population of the MAC protect list with source MAC addresses learned on the SAP belonging to this template.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateShgRestProtSrcMacAct 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.55
The value of the object pwTemplateShgRestProtSrcMacAct indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP or SDP-BIND belonging to pwTemplateShgName. When the value of this object is 'disable' the SAP or SDP-BIND belonging to pwTemplateShgName will be placed in the operational down state, with the operating flag 'recProtSrcMac' set. When the value of this object is 'alarmOnly', the SAP belonging to pwTemplateShgName will be left up and only a notification, sapReceivedProtSrcMac or sdpBindReceivedProtSrcMac, will be generated. When the value of this object is 'discardFrame', the SAP or SDP-BIND belonging to pwTemplateShgName will start discarding the frame in addition to generating sapReceivedProtSrcMac or sdpBindReceivedProtSrcMac notification.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(1), alarmOnly(2), discardFrame(3)  

pwTemplateShgAutoLearnMacProtect 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.56
The value of pwTemplateShgAutoLearnMacProtect specifies whether to enable automatic population of the MAC protect list with source MAC addresses learned on the SAP or SDP-BIND belonging to pwTemplateShgName.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateIngQoSNetworkPlcyId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.57
The value of the pwTemplateIngQoSNetworkPlcyId specifies the ingress QoS network policy applied to this PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TSdpIngressPolicyID  

pwTemplateEgrQoSNetworkPlcyId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.58
The value of the pwTemplateEgrQoSNetworkPlcyId specifies the egress QoS network policy applied to this PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TSdpEgressPolicyID  

pwTemplateIngQoSFpRedirectQGrp 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.59
The value of pwTemplateIngQoSFpRedirectQGrp specifies the forwarding-plane queue group Policy for this PW template. This object must be set along with pwTemplateIngQoSNetworkPlcyId object. An 'inconsistentValue' error is returned if pwTemplateIngQoSFpRedirectQGrp is set to a non-default value and an entry corresponding to tmnxFPNum to which this PW template belongs does not exist in tmnxFPAccIngQGrpTable.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

pwTemplateEgrQoSPortRedirectQGrp 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.60
The value of pwTemplateEgrQoSPortRedirectQGrp specifies the forwarding-plane queue group Policy for this PW template. This object must be set along with pwTemplateEgrQoSNetworkPlcyId object. An 'inconsistentValue' error is returned if pwTemplateEgrQoSPortRedirectQGrp is set to a non-default value and an entry corresponding to tmnxFPNum to which this PW template belongs does not exist in tmnxFPAccIngQGrpTable.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

pwTemplateIngQoSInstanceId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.61
The value of pwTemplateIngQoSInstanceId specifies the instance of the forwarding-plane ingress Queue Group for this PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TQosQGrpInstanceIDorZero  

pwTemplateEgrQoSInstanceId 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.62
The value of pwTemplateEgrQoSInstanceId specifies the instance of the forwarding-plane egress Queue Group for this PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TQosQGrpInstanceIDorZero  

pwTemplateBlockOnPeerFault 1.3.6.1.4.1.6527.3.1.2.4.4.18.1.63
The value of pwTemplateBlockOnPeerFault specifies whether to block user traffic being forwarded when peer pw status bits have faults for this PW template.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

pwTemplateIgmpSnpgGrpSrcTblLC 1.3.6.1.4.1.6527.3.1.2.4.4.19
The value of pwTemplateIgmpSnpgGrpSrcTblLC indicates the sysUpTime at the time of the last modification of pwTemplateIgmpSnpgGrpSrcTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwTemplateIgmpSnpgGrpSrcTable 1.3.6.1.4.1.6527.3.1.2.4.4.20
A table that contains entries for static IGMP Snooping groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwTemplateIgmpSnpgGrpSrcEntry

pwTemplateIgmpSnpgGrpSrcEntry 1.3.6.1.4.1.6527.3.1.2.4.4.20.1
Information about a specific static IGMP Snooping groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwTemplateIgmpSnpgGrpSrcEntry  

pwTemplateIgmpSnpgGrpAddrType 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.1
The IP multicast group address type for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

pwTemplateIgmpSnpgGrpAddr 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.2
The IP multicast group address for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(0|4)  

pwTemplateIgmpSnpgSrcAddrType 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.3
The source address type for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

pwTemplateIgmpSnpgSrcAddr 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.4
The source address for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(0|4)  

pwTemplateIgmpSnpgRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.5
The value of pwTemplateIgmpSnpgRowStatus is used for the creation and deletion of static IGMP snooping entries.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwTemplateIgmpSnpgLastChngd 1.3.6.1.4.1.6527.3.1.2.4.4.20.1.6
The value of pwTemplateIgmpSnpgLastChngd indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwTemplateMfibAllowedMdaTblLC 1.3.6.1.4.1.6527.3.1.2.4.4.21
The value of pwTemplateMfibAllowedMdaTblLC indicates the sysUpTime at the time of the last modification of pwTemplateMfibAllowedMdaTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

pwTemplateMfibAllowedMdaTable 1.3.6.1.4.1.6527.3.1.2.4.4.22
The pwTemplateMfibAllowedMdaTable has an entry for each MFIB allowed MDA destination for an PW template.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwTemplateMfibAllowedMdaEntry

pwTemplateMfibAllowedMdaEntry 1.3.6.1.4.1.6527.3.1.2.4.4.22.1
Each row entry represents an MFIB allowed MDA destination for an PW template configured in the system. Entries can be created and deleted via SNMP SET operations on the object pwTemplateMfibMdaRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwTemplateMfibAllowedMdaEntry  

pwTemplateMfibMdaRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.22.1.1
The value of pwTemplateMfibMdaRowStatus controls the creation and deletion of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpBindTlsMrpTableLastChanged 1.3.6.1.4.1.6527.3.1.2.4.4.23
The value of sdpBindTlsMrpTableLastChanged indicates the sysUpTime at the time of the last modification of sdpBindTlsMrpTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindTlsMrpTable 1.3.6.1.4.1.6527.3.1.2.4.4.24
The sdpBindTlsMrpTable allows the operator to modify attributes of the Multiple Registration Protocol (MRP) feature for the TLS SDP Bind. This table contains an entry for each TLS SDP Bind created by the user using either sdpBindTlsTable or sdpBindMeshTlsTable. Rows in this table are created and deleted automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindTlsMrpEntry

sdpBindTlsMrpEntry 1.3.6.1.4.1.6527.3.1.2.4.4.24.1
Each row entry contains objects that allows the modification of the Multiple Registration Protocol feature for a specific SDP-Binding in a TLS service.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindTlsMrpEntry  

sdpBindTlsMrpLastChngd 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.1
The value of sdpBindTlsMrpLastChngd indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindTlsMrpJoinTime 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.2
The value of sdpBindTlsMrpJoinTime specifies a timer value in 10ths of seconds which determines the maximum rate at which attribute join messages can be sent on the SDP.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

sdpBindTlsMrpLeaveTime 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.3
The value of sdpBindTlsMrpLeaveTime specifies a timer value in 10ths of seconds which determines the amount of time a registered attribute is held in leave state before the registration is removed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 30..60  

sdpBindTlsMrpLeaveAllTime 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.4
The value of sdpBindTlsMrpLeaveAllTime specifies a timer value in 10ths of seconds which determines the frequency where all attribute declarations on the SDP are all refreshed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..300  

sdpBindTlsMrpPeriodicTime 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.5
The value of sdpBindTlsMrpPeriodicTime specifies a timer value in 10ths of seconds which determines the frequency of re-transmission of attribute declarations.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..100  

sdpBindTlsMrpPeriodicEnabled 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.6
The value of sdpBindTlsMrpPeriodicEnabled specifies whether re-transmission of attribute declarations is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sdpBindTlsMrpRxPdus 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.7
The value of sdpBindTlsMrpRxPdus indicates the number of MRP packets received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpDroppedPdus 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.8
The value of sdpBindTlsMrpDroppedPdus indicates the number of dropped MRP packets on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxPdus 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.9
The value of sdpBindTlsMrpTxPdus indicates the number of MRP packets transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxNewEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.10
The value of sdpBindTlsMrpRxNewEvent indicates the number of 'New' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxJoinInEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.11
The value of sdpBindTlsMrpRxJoinInEvent indicates the number of 'Join-In' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxInEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.12
The value of sdpBindTlsMrpRxInEvent indicates the number of 'In' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxJoinEmptyEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.13
The value of sdpBindTlsMrpRxJoinEmptyEvent indicates the number of 'Join Empty' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxEmptyEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.14
The value of sdpBindTlsMrpRxEmptyEvent indicates the number of 'Empty' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpRxLeaveEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.15
The value of sdpBindTlsMrpRxLeaveEvent indicates the number of 'Leave' MRP events received on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxNewEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.16
The value of sdpBindTlsMrpTxNewEvent indicates the number of 'New' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxJoinInEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.17
The value of sdpBindTlsMrpTxJoinInEvent indicates the number of 'Join-In' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxInEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.18
The value of sdpBindTlsMrpTxInEvent indicates the number of 'In' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxJoinEmptyEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.19
The value of sdpBindTlsMrpTxJoinEmptyEvent indicates the number of 'Join Empty' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxEmptyEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.20
The value of sdpBindTlsMrpTxEmptyEvent indicates the number of 'Empty' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpTxLeaveEvent 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.21
The value of sdpBindTlsMrpTxLeaveEvent indicates the number of 'Leave' MRP events transmitted on this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdpBindTlsMrpPolicy 1.3.6.1.4.1.6527.3.1.2.4.4.24.1.22
The value of sdpBindTlsMrpPolicy specifies the mrp policy to control which Group BMAC attributes will advertise on the egress SDP Bind.
Status: current Access: read-write
OBJECT-TYPE    
  TNamedItemOrEmpty  

sdpBindTlsMmrpTable 1.3.6.1.4.1.6527.3.1.2.4.4.25
This table contains an entry for each MAC address managed by Multiple MAC Registration Protocol (MMRP) on the SDP Bind for the TLS. Entries are dynamically created and destroyed by the system as the MAC Addresses are registered or declared in MMRP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindTlsMmrpEntry

sdpBindTlsMmrpEntry 1.3.6.1.4.1.6527.3.1.2.4.4.25.1
MMRP specific information about a MAC address managed by MMRP on a SDP Bind in a TLS.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindTlsMmrpEntry  

sdpBindTlsMmrpMacAddr 1.3.6.1.4.1.6527.3.1.2.4.4.25.1.1
The value of sdpBindTlsMmrpMacAddr indicates an ethernet MAC address which is being managed by MMRP on this SAP.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

sdpBindTlsMmrpDeclared 1.3.6.1.4.1.6527.3.1.2.4.4.25.1.2
The value of sdpBindTlsMmrpDeclared indicates whether the MRP applicant on this SAP is declaring this MAC address on behalf of MMRP.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindTlsMmrpRegistered 1.3.6.1.4.1.6527.3.1.2.4.4.25.1.3
The value of sdpBindTlsMmrpRegistered indicates whether the MRP registrant on this SAP has notified MMRP of a registration of this MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpBindTlsMmrpEndStation 1.3.6.1.4.1.6527.3.1.2.4.4.25.1.4
The value of sdpBindTlsMmrpEndStation indicates whether the MRP registrant on this SAP originated per end-station.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

sdpAutoBindBgpInfoTableLC 1.3.6.1.4.1.6527.3.1.2.4.4.26
The value of sdpAutoBindBgpInfoTableLC indicates the sysUpTime at the time of the last modification of sdpAutoBindBgpInfoTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpAutoBindBgpInfoTable 1.3.6.1.4.1.6527.3.1.2.4.4.27
The sdpAutoBindBgpInfoTable has an entry for each SDP Bind entry from sdpBindTable which was created as a result of BGP Auto-discovery.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpAutoBindBgpInfoEntry

sdpAutoBindBgpInfoEntry 1.3.6.1.4.1.6527.3.1.2.4.4.27.1
Each row entry contains BGP-related information for an SDP Bind entry created as a result of BGP Auto-discovery.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpAutoBindBgpInfoEntry  

sdpAutoBindBgpInfoTemplateId 1.3.6.1.4.1.6527.3.1.2.4.4.27.1.1
The value of sdpAutoBindBgpInfoTemplateId indicates the the value of the pwTemplateId object for the PW template entry used to create this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  PWTemplateId  

sdpAutoBindBgpInfoAGI 1.3.6.1.4.1.6527.3.1.2.4.4.27.1.2
The value of sdpAutoBindBgpInfoAGI indicates the Attachment Group Identifier (AGI) portion of the Generalized Id FEC element from the pseudowire setup for this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxVPNRouteDistinguisher  

sdpAutoBindBgpInfoSAII 1.3.6.1.4.1.6527.3.1.2.4.4.27.1.3
The value of sdpAutoBindBgpInfoSAII indicates the Source Attachment Individual Identifier (SAII) portion of the Generalized Id FEC element from the pseudowire setup for this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sdpAutoBindBgpInfoTAII 1.3.6.1.4.1.6527.3.1.2.4.4.27.1.4
The value of sdpAutoBindBgpInfoTAII indicates the Target Attachment Individual Identifier (TAII) portion of the Generalized Id FEC element from the pseudowire setup for this SDP Bind.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

svcTlsBgpADPWTempBindTblLC 1.3.6.1.4.1.6527.3.1.2.4.2.32
The value of svcTlsBgpADPWTempBindTblLC indicates the sysUpTime at the time of the last modification of svcTlsBgpADPWTempBindTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcTlsBgpADPWTempBindTable 1.3.6.1.4.1.6527.3.1.2.4.2.33
svcTlsBgpADPWTempBindTable contains entries for the associations between SDP Auto-Bind policies and a BGP Auto-Discovery context for a VPLS service.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SvcTlsBgpADAutoBindPlcyEntry

svcTlsBgpADPWTempBindEntry 1.3.6.1.4.1.6527.3.1.2.4.2.33.1
A SDP Auto-Bind Policy entry in the svcTlsBgpADPWTempBindTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SvcTlsBgpADAutoBindPlcyEntry  

svcTlsBgpADPWTempBindRowStatus 1.3.6.1.4.1.6527.3.1.2.4.2.33.1.1
The value of svcTlsBgpADPWTempBindRowStatus is used for the creation and deletion of associations between SDP Auto-Bind policies and a BGP Auto-Discovery context for a VPLS service.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

svcTlsBgpADPWTempBindLastChngd 1.3.6.1.4.1.6527.3.1.2.4.2.33.1.2
The value of svcTlsBgpADPWTempBindLastChngd indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcTlsBgpADPWTempBindSHG 1.3.6.1.4.1.6527.3.1.2.4.2.33.1.3
The value of svcTlsBgpADPWTempBindSHG specifies the split-horizon group to associate with the SDP Auto-Bind policy in this BGP Auto-Discovery context in a VPLS service. When this Auto-Bind policy is used to create an SDP, this split-horizon group will be associated with the SDP. The name specified must correspond to an existing split-horizon group in the VPLS service, otherwise an 'inconsistentValue' error will be returned.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

svcTlsBgpADPWTempBindOperGrp 1.3.6.1.4.1.6527.3.1.2.4.2.33.1.4
The value of the svcTlsBgpADPWTempBindOperGrp specifies the Operational-Group identifier associated with this pseudo-wire template binding.
Status: current Access: read-write
OBJECT-TYPE    
  TNamedItemOrEmpty  

svcTlsBgpADPWTempBindRTTblLC 1.3.6.1.4.1.6527.3.1.2.4.2.34
The value of svcTlsBgpADPWTempBindRTTblLC indicates the sysUpTime at the time of the last modification of svcTlsBgpADPWTempBindRTTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcTlsBgpADPWTempBindRTTable 1.3.6.1.4.1.6527.3.1.2.4.2.35
svcTlsBgpADPWTempBindTable contains entries for Route Targets associated with a SDP Auto-Bind policy and a BGP Auto-Discovery context for a VPLS service.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SvcTlsBgpADAutoBindPlcyRTEntry

svcTlsBgpADPWTempBindRTEntry 1.3.6.1.4.1.6527.3.1.2.4.2.35.1
A SDP Auto-Bind Policy Route Target entry in the svcTlsBgpADPWTempBindRTTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SvcTlsBgpADAutoBindPlcyRTEntry  

svcTlsBgpADPWTempBindRT 1.3.6.1.4.1.6527.3.1.2.4.2.35.1.1
The value of svcTlsBgpADPWTempBindRT is the Route Target associated with a PW template and a BGP Auto-Discovery context for a VPLS service. When advertisements are received with this Route Target, the PW template specified by the index, pwTemplateId, will be used to create the SDP.
Status: current Access: not-accessible
OBJECT-TYPE    
  TNamedItem  

svcTlsBgpADPWTempBindRTRowStat 1.3.6.1.4.1.6527.3.1.2.4.2.35.1.2
The value of svcTlsBgpADPWTempBindRTRowStat is used for the association of Route Targets with a SDP Auto-Bind policy and a BGP Auto-Discovery context for a VPLS service.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

svcL2RteTableLastChanged 1.3.6.1.4.1.6527.3.1.2.4.2.38
The value of svcL2RteTableLastChanged indicates the sysUpTime at the time of the last modification of svcL2RteTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcL2RteTable 1.3.6.1.4.1.6527.3.1.2.4.2.39
svcL2RteTable contains entries for L2 routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SvcL2RteEntry

svcL2RteEntry 1.3.6.1.4.1.6527.3.1.2.4.2.39.1
An L2 route entry in the svcL2RteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SvcL2RteEntry  

svcL2RteVsiPrefix 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.1
The value of svcL2RteVsiPrefix is the low-order 4 bytes of the Virtual Switch Instance idendifier (VSI-id) of the remote VSI for this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

svcL2RteRouteDistinguisher 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.2
The value of svcL2RteRouteDistinguisher is the high-order 6 bytes of the Virtual Switch Instance idendifier (VSI-id) of the remote VSI for this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxVPNRouteDistinguisher  

svcL2RteNextHopType 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.3
The value of svcL2RteNextHopType indicates the address type of svcL2RteNextHop.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

svcL2RteNextHop 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.4
The value of svcL2RteNextHop indicates the IP next hop for this L2 route. This value is equivilant to the IP address of the Far End of this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

svcL2RteSdpBindId 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.5
The value of svcL2RteSdpBindId indicates the SDP bind ID of the SDP bind that binds this VPLS context to the VSI indicated by svcL2RteRouteDistinguisher, svcL2RteVsiPrefix, and svcL2RteNextHop. The value of svcL2RteSdpBindId will be '0000000000000000'H if there was an error in creating the L2 route and the svcL2RteError will contain a string describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindId  

svcL2RtePwTemplateId 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.6
The value of svcL2RtePwTemplateId indicates the PW template associated with the SDP bind that binds this VPLS context to the VSI indicated by svcL2RteRouteDistinguisher, svcL2RteVsiPrefix, and svcL2RteNextHop.
Status: current Access: read-only
OBJECT-TYPE    
  PWTemplateId  

svcL2RteError 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.7
The value of svcL2RteError indicates an error message describing an error encountered when establishing this L2 route entry. The value of svcL2RteError will be a zero-length string when the L2 route is successfully established.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

svcL2RteLastErrorTime 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.8
The value of svcL2RteLastErrorTime indicates the sysUpTime at the time of the last error for this L2 route entry. If no errors were encountered for this entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcL2RteStatus 1.3.6.1.4.1.6527.3.1.2.4.2.39.1.9
The value of svcL2RteStatus indicates the status of the this L2 Route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

svcL2BgpVplsRteTable 1.3.6.1.4.1.6527.3.1.2.4.2.84
svcL2BgpVplsRteTable contains entries for L2 routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SvcL2BgpVplsRteEntry

svcL2BgpVplsRteEntry 1.3.6.1.4.1.6527.3.1.2.4.2.84.1
An L2 route entry in the svcL2BgpVplsRteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SvcL2BgpVplsRteEntry  

svcL2BgpVplsRteVeId 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.1
The value of svcL2BgpVplsRteVeId is the low-order 4 bytes of the Virtual Switch Instance idendifier (VSI-id) of the remote VSI for this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxSiteId  

svcL2BgpVplsRteRD 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.2
The value of svcL2BgpVplsRteRD is the high-order 6 bytes of the Virtual Switch Instance idendifier (VSI-id) of the remote VSI for this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxVPNRouteDistinguisher  

svcL2BgpVplsRteNextHopType 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.3
The value of svcL2BgpVplsRteNextHopType indicates the address type of svcL2BgpVplsRteNextHop.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

svcL2BgpVplsRteNextHop 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.4
The value of svcL2BgpVplsRteNextHop indicates the IP next hop for this L2 route. This value is equivilant to the IP address of the Far End of this L2 route.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

svcL2BgpVplsRteSdpBindId 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.5
The value of svcL2BgpVplsRteSdpBindId indicates the SDP bind ID of the SDP bind that binds this VPLS context to the VSI indicated by svcL2BgpVplsRteRD, svcL2BgpVplsRteVeId, and svcL2BgpVplsRteNextHop. The value of svcL2BgpVplsRteSdpBindId will be '0000000000000000'H if there was an error in creating the L2 route and the svcL2BgpVplsRteError will contain a string describing the error.
Status: current Access: read-only
OBJECT-TYPE    
  SdpBindId  

svcL2BgpVplsRtePwTemplateId 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.6
The value of svcL2BgpVplsRtePwTemplateId indicates the PW template associated with the SDP bind that binds this VPLS context to the VSI indicated by svcL2BgpVplsRteRD, svcL2BgpVplsRteVeId, and svcL2BgpVplsRteNextHop.
Status: current Access: read-only
OBJECT-TYPE    
  PWTemplateId  

svcL2BgpVplsRteError 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.7
The value of svcL2BgpVplsRteError indicates an error message describing an error encountered when establishing this L2 route entry. The value of svcL2BgpVplsRteError will be a zero-length string when the L2 route is successfully established.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

svcL2BgpVplsRteLastErrorTime 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.8
The value of svcL2BgpVplsRteLastErrorTime indicates the sysUpTime at the time of the last error for this L2 route entry. If no errors were encountered for this entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

svcL2BgpVplsRteControlWord 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.9
The value of svcL2BgpVplsRteControlWord indicates the control word advertised for this route.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

svcL2BgpVplsRtePathMtu 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.10
The value of svcL2BgpVplsRtePathMtu indicates the layer-2 path MTU for the pseudo-wire to the PE for this route.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

svcL2BgpVplsRteState 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.11
The value of svcL2BgpVplsRteState indicates state of the object for this route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

svcL2BgpVplsRteSeqDelivery 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.12
The value of svcL2BgpVplsRteSeqDelivery indicates the sequenced delivery flag advertiesed for this route.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

svcL2BgpVplsRteDF 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.13
The value of svcL2BgpVplsRteDF indicates the value of DF bit associated with this BGP VPLS L2 route entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

svcL2BgpVplsRteStatus 1.3.6.1.4.1.6527.3.1.2.4.2.84.1.14
The value of svcL2BgpVplsRteStatus indicates the status of the this BGP VPLS L2 Route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

svcApplyEvalPwTemplate 1.3.6.1.4.1.6527.3.1.2.4.4.28
OBJECT IDENTIFIER    

svcApplyEvalPwTemplateSvcId 1.3.6.1.4.1.6527.3.1.2.4.4.28.1
The value of the object svcApplyEvalPwTemplateSvcId specifies the service identifier to which this action applies.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxServId  

svcApplyEvalPwTemplateId 1.3.6.1.4.1.6527.3.1.2.4.4.28.2
The value of the object svcApplyEvalPwTemplateId specifies the pwTemplateId to apply on the service 'svcApplyEvalPwTemplateSvcId'.
Status: current Access: read-write
OBJECT-TYPE    
  PWTemplateId  

svcApplyEvalPwTemplateAction 1.3.6.1.4.1.6527.3.1.2.4.4.28.3
The value of svcApplyEvalPwTemplateAction when set to 'doAction' triggers the action to re-evaluate pseduo-wire template policy 'svcApplyEvalPwTemplateId' on the 'svcApplyEvalPwTemplateSvcId' service. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxActionType  

svcApplyEvalPwTemplateSuccess 1.3.6.1.4.1.6527.3.1.2.4.4.28.4
The value of the object svcApplyEvalPwTemplateSuccess indicates whether the action was successful. If the value of the object equals 'false', then the value of svcApplyEvalPwTemplateErrorMsg indicates the reason of the failure.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

svcApplyEvalPwTemplateErrorMsg 1.3.6.1.4.1.6527.3.1.2.4.4.28.5
The value of the object svcApplyEvalPwTemplateErrorMsg indicates the reason of failure, in case the value of the object svcApplyEvalPwTemplateSuccess is equal to 'false'. If the value of the object svcApplyEvalPwTemplateSuccess is equal to 'true', this object contains an empty string.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

svcApplyEvalPwTemplateTime 1.3.6.1.4.1.6527.3.1.2.4.4.28.6
The value of the object svcApplyEvalPwTemplateTime indicates the value of sysUpTime at the last time that the object svcApplyEvalPwTemplateSuccess was written by the system.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindPbbTable 1.3.6.1.4.1.6527.3.1.2.4.4.29
A table that contains Provider Backbone Bridging (PBB/IEEE 802.1ah) spoke SDP Bind information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindPbbEntry

sdpBindPbbEntry 1.3.6.1.4.1.6527.3.1.2.4.4.29.1
PBB I-Component instance-specific information about an SDP Bind in the B-Component instance. Entries in this table can be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindPbbEntry  

sdpBindPbbSvcIdIVpls 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.1
The value of the object sdpBindPbbSvcIdIVpls specifies the Service identifier of the I-Component instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxServId  

sdpBindPbbSvcIdBVpls 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.2
The value of the object sdpBindPbbSvcIdBVpls specifies the Service identifier of the B-Component instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxServId  

sdpBindPbbId 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.3
The value of the object sdpBindPbbId specifies the identifier of the SDP Binding in the B-Component instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdpBindId  

sdpBindPbbRowStatus 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.4
The value of sdpBindPbbRowStatus specifies the row status of this row. The only values supported during a set operation are 'createAndGo' and 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdpBindPbbLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.5
The value of sdpBindPbbLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindPbbIgmpSnpgMRouter 1.3.6.1.4.1.6527.3.1.2.4.4.29.1.6
The value of the object sdpBindPbbIgmpSnpgMRouter specifies if a multicast router is attached behind this SDP Bind.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

sdpBindFPropBMacAddrTblLastChgd 1.3.6.1.4.1.6527.3.1.2.4.4.30
The value of sdpBindFPropBMacAddrTblLastChgd indicates the sysUpTime at the last modification of sdpBindFPropBMacAddrTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

sdpBindFPropBMacAddrTable 1.3.6.1.4.1.6527.3.1.2.4.4.31
sdpBindFPropBMacAddrTable contains the optional configured backbone MAC (BMac) addresses (or MAC names) for each SDP binding. This table extends the information in sdpBindTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdpBindFPropBMacAddrEntry

sdpBindFPropBMacAddrEntry