CISCO-LWAPP-MESH-MIB

File: CISCO-LWAPP-MESH-MIB.mib (70718 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB CISCO-LWAPP-AP-MIB CISCO-LWAPP-TC-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 Gauge32 NOTIFICATION-TYPE
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
TruthValue TimeStamp MacAddress
TimeInterval SnmpAdminString cLApSysMacAddress
cLApName CLDot11Channel ciscoMgmt

Defined Types

ClMeshNodeEntry  
SEQUENCE    
  clMeshNodeRole INTEGER
  clMeshNodeGroupName SnmpAdminString
  clMeshNodeBackhaul INTEGER
  clMeshNodeBackhaulDataRate Unsigned32
  clMeshNodeEthernetBridge TruthValue
  clMeshNodeEthernetLinkStatus INTEGER
  clMeshNodePublicSafetyBackhaul TruthValue
  clMeshNodeParentMacAddress MacAddress
  clMeshNodeHeaterStatus INTEGER
  clMeshNodeInternalTemp Integer32
  clMeshNodeType INTEGER
  clMeshNodeHops Gauge32
  clMeshNodeChildCount Gauge32
  clMeshNodeBackhaulRadio INTEGER
  clMeshNodeBHDataRate INTEGER

ClMeshNeighborEntry  
SEQUENCE    
  clMeshNeighborMacAddress MacAddress
  clMeshNeighborType BITS
  clMeshNeighborLinkSnr Integer32
  clMeshNeighborChannel CLDot11Channel
  clMeshNeighborUpdate TimeStamp

Defined Values

ciscoLwappMeshMIB 1.3.6.1.4.1.9.9.616
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol (LWAPP) tunnel from Light-weight Access Points. This MIB represents information used in Wireless Mesh Network. MAP APs associates directly with RAP APs or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP) with another AP forms parent-child relationship. The deployment of the controller (referred to as CC in the diagram), mesh nodes (RAP and MAP) LWAPP APs, client(MS) and NMS appear as follows. +.......+ +.......+ + + + + + NMS + + NMS + + + + + +.......+ +.......+ . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + RAP + + RAP + + RAP + + RAP + + RAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MAP + + MS + + MAP + + MAP + + MAP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . .. . . . . .. . . . . .. . . . . . . +......+ +......+ +......+ +......+. +......+ + + + + + + + + + + + MAP + + MAP + + MAP + + MAP + + MS + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters to the LWAPP APs. The APs encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Station ( MS ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Station and client are used interchangeably. Network Management System ( NMS ) The station from which the administrator manages the wired and wireless networks. Mesh Node A mesh node is defined as a physical or logical entity in the mesh network participating in forming the mesh backhaul. RAP and MAP are two types of mesh nodes supported in mesh network. Root AP (RAP) The AP forming the bridge between a wired and a mesh network with an Ethernet interface to the wired network and a 802.11 radio interface to the mesh network Mesh AP (MAP). The AP extending wireless coverage similar to a repeater in a mesh network and consists of a 802.11 uplink and a 802.11 downlink. On a single-radio backhaul, both uplink and downlink exist on the same radio and are logical links only. On a multi-radio backhaul, they may exist on different radios. Mesh Network Network starting with the wireless backhaul downlink of the RAP and all the entities below except any attached network to the Ethernet link of MAPs. A mesh network below a single RAP is also referred to as a 'Mesh Sector'.A mesh network consists of mesh nodes. A single mesh network is always augmented to a single wired network. Mesh Link A logical 802.11 link between two mesh nodes. A single link is point-to-point. All point-to-multipoint links are considered as multiple mesh links. Often referred to as mesh backhaul link. Mesh Backhaul A mesh backhaul consists of mesh nodes and mesh links terminating at a RAP. This necessarily creates a one- to-one relationship between a 'mesh network', 'mesh sector' and a 'mesh backhaul' where these terms can be used interchangeably. SNR Signal to Noise ratio on the 802.11 radio. Bridged network The bridged network is defined as the network(s) attached to the Ethernet port of any MAP. There can be multiple such networks attached to a single mesh network. Mesh Node Roaming A mesh node may change its parent mesh node naturally when the RF/network condition changes. Child Mesh node will re-associate and re-authenticate to new parent mesh node. Mesh Security supports two types of mesh node roaming. Intra-controller - LWAPP session is not lost. Inter-controller - LWAPP session is lost. AMSDU Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU. IDS Intrusion Detection Sysytem. A software to detect unwanted attempts at accessing,manipulating, and or disabling of WLC. ExtendedUA For 1524 APs, it has two 802.11a radios (slot1, slot2) and one 802.11b/g radio (slot0). This will enable the client access on 802.11a (slot1) for 152x series mesh access points with two 802.11a radios, where the wireless client association can be done over the 802.11a radio (slot1). With this feature we are providing an option to enable/disable backhaul client on another 802.11a radio (slot2) as well. This implies that a 152x series mesh access points with two 802.11a radios can carry both backhaul traffic and 802.11a (slot1, slot2) client traffic over the same radios. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
MODULE-IDENTITY    

ciscoLwappMeshMIBNotifs 1.3.6.1.4.1.9.9.616.0
OBJECT IDENTIFIER    

ciscoLwappMeshMIBObjects 1.3.6.1.4.1.9.9.616.1
OBJECT IDENTIFIER    

ciscoLwappMeshMIBConform 1.3.6.1.4.1.9.9.616.2
OBJECT IDENTIFIER    

ciscoLwappMeshConfig 1.3.6.1.4.1.9.9.616.1.1
OBJECT IDENTIFIER    

ciscoLwappMeshGlobalConfig 1.3.6.1.4.1.9.9.616.1.2
OBJECT IDENTIFIER    

ciscoLwappMeshNeighborsStatus 1.3.6.1.4.1.9.9.616.1.3
OBJECT IDENTIFIER    

ciscoLwappMeshNotifControlConfig 1.3.6.1.4.1.9.9.616.1.4
OBJECT IDENTIFIER    

ciscoLwappMeshMIBNotifObjects 1.3.6.1.4.1.9.9.616.1.5
OBJECT IDENTIFIER    

clMeshNodeTable 1.3.6.1.4.1.9.9.616.1.1.1
This table represents information about the 802.11 LWAPP Access Points that have joined the controller as part of a mesh network.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClMeshNodeEntry

clMeshNodeEntry 1.3.6.1.4.1.9.9.616.1.1.1.1
Each entry represents a conceptual row in this table. An entry is created when MAP joins the controller. The entry is removed when the mesh node lose their association with the controller due to loss of communication with controller or when a mesh node is reset.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClMeshNodeEntry  

clMeshNodeRole 1.3.6.1.4.1.9.9.616.1.1.1.1.1
This object represents the role of mesh AP which has joined the controller. See glossary section above for detail about MAP and RAP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER map(1), rap(2)  

clMeshNodeGroupName 1.3.6.1.4.1.9.9.616.1.1.1.1.2
This object represents the group name of the mesh sector. MAP AP will join the mesh sector which has the same group name configured on RAP AP.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..10)  

clMeshNodeBackhaul 1.3.6.1.4.1.9.9.616.1.1.1.1.3
This object represents 802.11 interface type of the backhaul link. See Mesh Link in glossary section for more detail on backhaul link. dot11a - 802.11a radio is used as backhaul link. dot11b - 802.11b radio is used as backhaul link. dot11g - 802.11g radio is used as backhaul link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot11a(1), dot11b(2), dot11g(3)  

clMeshNodeBackhaulDataRate 1.3.6.1.4.1.9.9.616.1.1.1.1.4
This object represents the rate at which packets are sent on the backhaul link. This object has been deprecated for clMeshNodeBHDataRate.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Unsigned32  

clMeshNodeEthernetBridge 1.3.6.1.4.1.9.9.616.1.1.1.1.5
A value of 'true' indicates ethernet bridging is enable on this mesh node. A value of 'false indicates ethernet bridging is not enable on this mesh node. Ethernet bridging can be enabled on RAP or MAP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshNodeEthernetLinkStatus 1.3.6.1.4.1.9.9.616.1.1.1.1.6
This object represents if the link is up or down on the ethernet port of the RAP or MAP. up - ethernet link is up. down - ethernet link is down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

clMeshNodePublicSafetyBackhaul 1.3.6.1.4.1.9.9.616.1.1.1.1.7
4.9Ghz considered to be public safety band and is limited to some service providers. A value of true indicates that 4.9 Ghz can be used on backhaul link by selecting channel on the 802.11a backhaul radio. Since public safety is now set at the controller level rather then at the AP level, use of this variable is deprecated, and the global setting clMeshPublicSafetyBackhaulGlobal should be used instead.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshNodeParentMacAddress 1.3.6.1.4.1.9.9.616.1.1.1.1.8
This object represents the MAC address of a parent mesh node. In case of RAP this object will return 0000000000000.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

clMeshNodeHeaterStatus 1.3.6.1.4.1.9.9.616.1.1.1.1.9
This object represents the heater status of the mesh node. on - heater is in operation off - heater is not operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

clMeshNodeInternalTemp 1.3.6.1.4.1.9.9.616.1.1.1.1.10
This object represents the internal temperature of mesh node in celsius.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

clMeshNodeType 1.3.6.1.4.1.9.9.616.1.1.1.1.11
This object represents the type of mesh node. indoor - Mesh node which is manufactured to be used inside the building. outdoor - Mesh node which can be used outside building in open environment.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER indoor(1), outdoor(2)  

clMeshNodeHops 1.3.6.1.4.1.9.9.616.1.1.1.1.12
This object represents the number of hops a MAP mesh node is from RAP. When the clMeshNodeRole is set to 'RAP' this object will return a value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

clMeshNodeChildCount 1.3.6.1.4.1.9.9.616.1.1.1.1.13
This object represents the number of children MAPs of a RAP or a MAP.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

clMeshNodeBackhaulRadio 1.3.6.1.4.1.9.9.616.1.1.1.1.14
This object specifies the type of radio used for backhaul access. unknown (1) unsupported APs dot11bg (2) The value dot11b sets the 802.11b radio as backhaul radio dot11a (3) The value dot11a sets the 802.11a radio as backhaul radio
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), dot11bg(2), dot11a(3)  

clMeshNodeBHDataRate 1.3.6.1.4.1.9.9.616.1.1.1.1.15
This object represents the rate at which packets are sent on the backhaul link. Depending on the backhaul radio type, denoted by clMeshNodeBackhaul object, data rate will vary. If the value of clMeshNodeBackhaul object is 'dot11a', data rates can be one of the following possible values. mbps6(4) mbps9(5) mbps12(7) mbps18(8) mbps24(9) mbps36(10) mbps48(11) mbps54(12) auto(13) Additionally following data rates are supported if 802.11a supports 11n. htMcs0(14) htMcs1(15) htMcs2(16) htMcs3(17) htMcs4(18) htMcs5(19) htMcs6(20) htMcs7(21) htMcs8(22) htMcs9(23) htMcs10(24) htMcs11(25) htMcs12(26) htMcs13(27) htMcs14(28) htMcs15(29) If the value of clMeshNodeBackhaul object is 'dot11b', then data rate can be one of the following possible values. mbps1(1) mbps2(2) mbps5point5(3) mbps11(6) auto(13) IIf the value of clMeshNodeBackhaul object is 'dot11g', then data rate can be one of the following possible values. mbps1(1) mbps2(2) mbps5point5(3) mbps6(4) mbps9(5) mbps11(6) mbps12(7) mbps18(8) mbps24(9) mbps36(10) mbps48(11) mbps54(12) auto(13)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mbps1(1), mbps2(2), mbps5point5(3), mbps6(4), mbps9(5), mbps11(6), mbps12(7), mbps18(8), mbps24(9), mbps36(10), mbps48(11), mbps54(12), auto(13), htMcs0(14), htMcs1(15), htMcs2(16), htMcs3(17), htMcs4(18), htMcs5(19), htMcs6(20), htMcs7(21), htMcs8(22), htMcs9(23), htMcs10(24), htMcs11(25), htMcs12(26), htMcs13(27), htMcs14(28), htMcs15(29)  

clMeshNodeRange 1.3.6.1.4.1.9.9.616.1.2.1
This object represents the optimal distance in feet between RAP and MAP for backhaul link without degrading SNR value.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 150..132000  

clMeshBackhaulClientAccess 1.3.6.1.4.1.9.9.616.1.2.2
This object represents if client access is to be enable on backhaul link. If AP has two radios,802.11a and 802.11bg, then radio which is used as backhaul link does not have client access. A value of 'true' indicates client access is present on backhaul link. If AP has only one radio then same radio is used for backhaul and client access.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshMacFilterList 1.3.6.1.4.1.9.9.616.1.2.3
If this object is 'true' then any mesh node joining controller will be authenticated against this list. If this object is 'false' then mesh node can join controller even if mesh node MAC address is not in MAC filter list.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshMeshNodeAuthFailureThreshold 1.3.6.1.4.1.9.9.616.1.2.4
This object represents the authorization failure threshold value. When the number of failures exceeds this value then 'ciscoLwappMeshAuthFailure' notification is raised.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..30  

clMeshMeshChildAssociationFailuresThreshold 1.3.6.1.4.1.9.9.616.1.2.5
This object represents the number of failed association to controller occurred through a parent mesh node. When this values exceeds then 'ciscoLwappMeshChildExcludedParent' notification is raised.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..30  

clMeshMeshChildExcludedParentInterval 1.3.6.1.4.1.9.9.616.1.2.6
This object represents the time interval during which a child mesh node will exclude a parent mesh node. During this interval child will not try to associate the controller through the parent mesh node.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 18000..96000  

clMeshSNRThresholdAbate 1.3.6.1.4.1.9.9.616.1.2.7
This object represents the abate threshold value of SNR. This threshold value is use to determine if the SNR value seen by the child mesh node has reached acceptable level and is use to trigger the 'ciscoLwappMeshAbateSNR' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 3..50  

clMeshSNRThresholdOnset 1.3.6.1.4.1.9.9.616.1.2.8
This object represents the onset threshold value of SNR. This threshold value is use to determine if the SNR value seen by the child mesh node has reached below unacceptable level and is use to trigger the 'ciscoLwappMeshOnsetSNR' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 3..50  

clMeshSNRCheckTimeInterval 1.3.6.1.4.1.9.9.616.1.2.9
This object represents the time interval after which SNR value is checked by child mesh node.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 18000..96000  

clMeshExcessiveParentChangeThreshold 1.3.6.1.4.1.9.9.616.1.2.10
This object represents the threshold for the number of times a child mesh node changes its parent. If number of parent change exceeds this value with in the time interval defined by object 'clMeshExcessiveParentChangeInterval' then the 'ciscoLwappMeshExcessiveParentChange' notification is raised.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

clMeshExcessiveParentChangeInterval 1.3.6.1.4.1.9.9.616.1.2.11
This object represents the time interval during which number of times a child mesh node changes its parent change is counted. If number of parent change exceeds the value defined by the object 'clMeshExcessiveParentChangeThreshold' with in this time interval then the 'ciscoLwappMeshExcessiveParentChange' notification is raised.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval 180000..360000  

clMeshBackgroundScan 1.3.6.1.4.1.9.9.616.1.2.12
A value of 'true' indicates the MAP mesh node scans its neighbors on different channel other than only its current channel on backhaul link. This scanning helps MAP mesh node to quickly determine its new parent on different channels.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshAuthenticationMode 1.3.6.1.4.1.9.9.616.1.2.13
This object represents authentication mode of RAP and MAP mesh nodes in controller. none - no authentication is done. psk - pre shared key. Keys provided during manufacturing will be used for authentication of mesh node. eap - extensible authentication protocol is used to authenticate mesh node. A value of 'eap' indicates, authentication can happen by local-auth in controller or by RADIUS server configured in controller.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), eap(2), psk(3)  

clMeshExcessiveHopCountThreshold 1.3.6.1.4.1.9.9.616.1.2.14
This object represents threshold number of hops from the MAP node to the RAP. Crossing this value will raise the 'ciscoLwappMeshExcessiveHopCount' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

clMeshExcessiveRapChildThreshold 1.3.6.1.4.1.9.9.616.1.2.15
This object represents threshold number of children MAPs attached to a parent RAP. Crossing this value will raise the 'ciscoLwappMeshExcessiveChildren' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

clMeshExcessiveMapChildThreshold 1.3.6.1.4.1.9.9.616.1.2.16
This object represents threshold number of children MAPs attached to a parent MAP. Crossing this value will raise the 'ciscoLwappMeshExcessiveChildren' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

clMeshHighSNRThresholdAbate 1.3.6.1.4.1.9.9.616.1.2.17
This object represents the abate threshold value of SNR. This threshold value is used to determine if the SNR value seen by the child mesh node has reached below this level and is use to trigger the 'ciscoLwappMeshAbateHighSNR' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 50..80  

clMeshHighSNRThresholdOnset 1.3.6.1.4.1.9.9.616.1.2.18
This object represents the onset threshold value of SNR. This threshold value is use to determine if the SNR value seen by the child mesh node has reached above this level and is use to trigger the 'ciscoLwappMeshOnsetHighSNR' notification.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 50..80  

clMeshPublicSafetyBackhaulGlobal 1.3.6.1.4.1.9.9.616.1.2.19
4.9Ghz considered to be public safety band and is limited to some service providers. A value of true indicates that 4.9 Ghz can be used on backhaul link by selecting channel on the 802.11a backhaul radio. This setting applies at the controller level. The prior per AP setting clMeshNodePublicSafetyBackhaul is deprecated as a result.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshisAMSDUEnable 1.3.6.1.4.1.9.9.616.1.2.20
This object represents the AMSDU status. true : Turns on AMSDU. false : Turns off AMSDU.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshIsIdsEnable 1.3.6.1.4.1.9.9.616.1.2.21
This object represents the IDS status. true : Turns on IDS feature. false : Turns off IDS feature.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshIsDCAChannelsEnable 1.3.6.1.4.1.9.9.616.1.2.22
This object represents the DCA Channel status. true : Turns on DCA feature for AP1524SB. false : Turns off DCA feature for AP1524SB. This is not implies for non-1524SB APs. Error will return if it is set for non-1524SB APs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshIsExtendedUAEnable 1.3.6.1.4.1.9.9.616.1.2.23
This object represents the ExtendedUA status. true : Turns on ExtendedUA feature. false : Turns off ExtendedUA feature.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshNeighborTable 1.3.6.1.4.1.9.9.616.1.3.1
This table represents information about neighbors of any mesh node. Neighbor AP can be on same or different mesh sector. Any mesh node is neighbor of a mesh node, if it can detect 802.11 signals on any channels. Child or parent mesh node also considers as neighbors.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClMeshNeighborEntry

clMeshNeighborEntry 1.3.6.1.4.1.9.9.616.1.3.1.1
An (conceptual) entry in this table is created when mesh node detects neighbor mesh nodes. Entries are removed when the mesh node does not detect AP as neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClMeshNeighborEntry  

clMeshNeighborMacAddress 1.3.6.1.4.1.9.9.616.1.3.1.1.1
This object represents MAC address of neighbor mesh node.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

clMeshNeighborType 1.3.6.1.4.1.9.9.616.1.3.1.1.2
This object represents type of neighbor mesh node. parent - Neighbor mesh node is a parent mesh node of this mesh node. neighbor - Its a neighbor mesh node. It can be on same or different mesh-sector. excluded - Neighbor mesh node is excluded by this mesh node. child - Neighbor mesh node is child of this mesh node. beacon - Neighbor mesh node found by passive scanning. Default - Neighbor mesh node connected using a mismatched bridge group name
Status: current Access: read-only
OBJECT-TYPE    
  BITS parent(0), neighbor(1), excluded(2), child(3), beacon(4), default(5)  

clMeshNeighborLinkSnr 1.3.6.1.4.1.9.9.616.1.3.1.1.3
This object represents the SNR value seen by this mesh node from neighbor mesh node.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

clMeshNeighborChannel 1.3.6.1.4.1.9.9.616.1.3.1.1.4
This object represents the channel on which neighbor mesh node is operating.
Status: current Access: read-only
OBJECT-TYPE    
  CLDot11Channel  

clMeshNeighborUpdate 1.3.6.1.4.1.9.9.616.1.3.1.1.5
This object represents when the neighbor table was last updated. This value is represented as a instance of sysUp time.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

clMeshAuthFailureNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.1
This object controls the generation of 'ciscoLwappMeshAuthFailure' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshChildExcludedParentNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.2
This object controls the generation of 'ciscoLwappMeshChildExcludedParent' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshParentChangeNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.3
This object controls the generation of 'ciscoLwappMeshParentChange' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshChildMovedNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.4
This object controls the generation of 'ciscoLwappMeshChildMoved' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshExcessiveParentChangeNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.5
This object controls the generation of 'ciscoLwappMeshExcessiveParentChange' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshPoorSNRNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.6
This object controls the generation of 'ciscoLwappMeshOnsetSNR' and 'ciscoLwappMeshAbateSNR' notifications. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will be not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshConsoleLoginNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.7
This object controls the generation of 'ciscoLwappMeshConsoleLogin' notification. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshDefaultBridgeGroupNameNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.8
This object controls the generation of 'ciscoLwappMeshDefaultBridgeGroupName' notification. A value of 'true' indicates this notification will be generated. A value of 'false' indicates this notification will not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshExcessiveHopCountNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.9
This object controls the generation of 'ciscoLwappMeshExcessiveHopCount' notification. A value of 'true' indicates this notification will be generated. A value of 'false' indicates this notification will not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshExcessiveChildrenNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.10
This object controls the generation of 'ciscoLwappMeshExcessiveChildren' notification. A value of 'true' indicates this notification will be generated. A value of 'false' indicates this notification will not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshHighSNRNotifEnabled 1.3.6.1.4.1.9.9.616.1.4.11
This object controls the generation of 'ciscoLwappMeshOnsetHighSNR' and 'ciscoLwappMeshAbateHighSNR' notifications. A value of 'true' indicates notification will be generated. A value of 'false' indicates notification will not be generated.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

clMeshNodeMacAddress 1.3.6.1.4.1.9.9.616.1.5.1
This object specifies the MAC address of a LWAPP AP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

clMeshAuthFailureReason 1.3.6.1.4.1.9.9.616.1.5.2
This object specifies the failure reason when a mesh node failed to authenticate through a controller to an Authentication Server. notInMacFilterList - MAC address of a mesh node is not configured in MAC filter list. securityFailure - Authentication server sent rejection for the mesh node.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER notInMacFilterList(1), securityFailure(2)  

clMeshPreviousParentMacAddress 1.3.6.1.4.1.9.9.616.1.5.3
This object specifies the MAC address of previous parent Mesh Node.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

clMeshConsoleLoginStatus 1.3.6.1.4.1.9.9.616.1.5.4
This object specifies the status of console login at MAP mesh node.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER success(1), failure(2)  

ciscoLwappMeshAuthFailure 1.3.6.1.4.1.9.9.616.0.1
A mesh node can fail to authorize if the MAC address of mesh node is not in the MAC filter list or security failure by authentication server. Reason is specified by 'clMeshAuthFailureReason'. This notification is sent by the agent when number of failures exceeds threshold defined by object 'clMeshMeshNodeAuthFailureThreshold'. Object 'clMeshAuthFailureNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshChildExcludedParent 1.3.6.1.4.1.9.9.616.0.2
This notification will be sent by agent when child mesh node exceeds threshold limit of number of discovery response timeouts defined by object 'clMeshMeshChildAssociationFailuresThreshold'. The child mesh node will not try to associate excluded parent mesh node for the interval defined by object 'clMeshMeshChildExcludedParentInterval'. The child mesh node will remember the excluded parent MAC address and when it joins the network it will inform the controller. 'cLApName' specifies child mesh node name. Child MAC address is sent as part of index. Object 'clMeshChildExcludedParentNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshParentChange 1.3.6.1.4.1.9.9.616.0.3
This notification is sent by the agent when a child mesh node changes its parent. Child mesh node will remember its previous parent and when it joins the network it will inform controller about change of its parent. 'cLApName' specifies child mesh node name. Child mesh node MAC address is sent as part of index. Object 'clMeshParentChangeNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshChildMoved 1.3.6.1.4.1.9.9.616.0.4
This notification is sent by the agent when a parent mesh node loses connection with its child mesh node. 'cLApName' specifies parent mesh node name. Parent and child MAC address are sent as part of index. Object 'clMeshChildMovedNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshExcessiveParentChange 1.3.6.1.4.1.9.9.616.0.5
This notification is sent by the agent when child mesh node changes its parent frequently. Each mesh node keeps count of number of parent changes in fixed time. If it exceeds the threshold defined by 'clMeshExcessiveParentChangeThreshold' then child mesh node informs the controller. 'cLApName' specifies child mesh node name. Child and Parent MAC address are sent as part of index. Object 'clMeshExcessiveParentChangeNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshOnsetSNR 1.3.6.1.4.1.9.9.616.0.6
This notification is sent by the agent when child mesh node detects lower SNR on backhaul link then defined by object 'clMeshSNRThresholdOnset'. SNR value is checked after interval defined by object 'clMeshSNRCheckTimeInterval'. 'ciscoLwappMeshAbateSNR' notification will be sent to clear this notification. 'cLApName' specifies child mesh node name. Child and parent MAC address are sent as part of index. Object 'clMeshPoorSNRNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshAbateSNR 1.3.6.1.4.1.9.9.616.0.7
This notification is sent by the agent to clear 'ciscoLwappMeshOnsetSNR' notification when child mesh node detects SNR on backhaul link is higher then the object defined by 'clMeshSNRThresholdAbate'. SNR value is checked after interval defined by object 'clMeshSNRCheckTimeInterval'. 'cLApName' specifies child mesh node name. Child and parent MAC address are sent as part of index. Object 'clMeshPoorSNRNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshConsoleLogin 1.3.6.1.4.1.9.9.616.0.8
This notification is sent by the agent when login on MAP console is successful or failure after three attempts. 'cLApName' specifies mesh node name. Object 'clMeshConsoleLoginNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshDefaultBridgeGroupName 1.3.6.1.4.1.9.9.616.0.9
This notification is sent by the agent when MAP mesh node joins parent using 'default' bridge group name. The child node mac address is sent as the index of cLApName.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshExcessiveHopCount 1.3.6.1.4.1.9.9.616.0.10
This notification is sent by the agent when the number of hops from the MAP node to the RAP exceeds the threshold defined by 'clMeshExcessiveHopCountThreshold'. The MAP MAC address is sent as part of the index. These alarms are raised once in three minutes, the periodicity of AP sending the statistics to WLC.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshExcessiveChildren 1.3.6.1.4.1.9.9.616.0.11
This notification is sent by the agent when the child count exceeds clMeshExcessiveRapChildThreshold for a RAP and clMeshExcessiveMapChildThreshold for a MAP. The node MAC address is sent as a part of the index. These alarms are raised once in three minutes, the periodicity of AP sending the statistics to WLC.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshOnsetHighSNR 1.3.6.1.4.1.9.9.616.0.12
This notification is sent by the agent when child mesh node detects higher SNR on backhaul link then defined by object 'clMeshHighSNRThresholdOnset'. SNR value is checked after interval defined by object 'clMeshSNRCheckTimeInterval'. 'ciscoLwappMeshAbateHighSNR' notification will be sent to clear this notification. 'cLApName' specifies child mesh node name. Child and parent MAC address are sent as part of index. Object 'clMeshHighSNRNotifEnabled' controls the generation of this notification. These alarms are raised once in three minutes, the periodicity of AP sending the statistics to WLC.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshAbateHighSNR 1.3.6.1.4.1.9.9.616.0.13
This notification is sent by the agent to clear 'ciscoLwappMeshOnsetSNR' notification when child mesh node detects SNR on backhaul link, which is lower than the object defined by 'clMeshHighSNRThresholdAbate'. SNR value is checked after interval defined by object 'clMeshSNRCheckTimeInterval'. 'clMeshNeighborLinkSnr' represents the SNR value seen by this mesh node from neighbor mesh node. 'cLApName' specifies child mesh node name. Child and parent MAC address are sent as part of index. Object 'clMeshHighSNRNotifEnabled' controls the generation of this notification.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

ciscoLwappMeshMIBCompliances 1.3.6.1.4.1.9.9.616.2.1
OBJECT IDENTIFIER    

ciscoLwappMeshMIBGroups 1.3.6.1.4.1.9.9.616.2.2
OBJECT IDENTIFIER    

ciscoLwappMeshMIBCompliance 1.3.6.1.4.1.9.9.616.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappMeshMIB module.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

ciscoLwappMeshMIBComplianceR01 1.3.6.1.4.1.9.9.616.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappMeshMIB module.This deprecates ciscoLwappMeshMIBCompliance
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

ciscoLwappMeshMIBComplianceR02 1.3.6.1.4.1.9.9.616.2.1.3
The compliance statement for the SNMP entities that implement the ciscoLwappMeshMIB module.This deprecates ciscoLwappMeshMIBComplianceR01
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

ciscoLwappMeshConfigGroup 1.3.6.1.4.1.9.9.616.2.2.1
This collection of objects represent the global and mesh node specific configuration and monitor parameters.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNeighborStatusGroup 1.3.6.1.4.1.9.9.616.2.2.2
This collection of objects represent the neighbor status of any mesh node.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNotifControlGroup 1.3.6.1.4.1.9.9.616.2.2.3
This collection of objects represent the flags to control the generation of notification.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNotifObjsGroup 1.3.6.1.4.1.9.9.616.2.2.4
This collection of objects represent the information carried by the mesh network related notifications sent by the agent to a network management station.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNotifsGroup 1.3.6.1.4.1.9.9.616.2.2.5
This collection of objects represent the mesh network related notifications sent by the agent to a network management station.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

ciscoLwappMeshConfigGroupSup1 1.3.6.1.4.1.9.9.616.2.2.6
This collection of objects represent the global and mesh node specific configuration and monitor parameters.
Status: deprecated Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNotifControlGroupSup1 1.3.6.1.4.1.9.9.616.2.2.7
This collection of objects represent the flags to control the generation of notification.This deprecates ciscoLwappMeshNotifControlGroup.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

ciscoLwappMeshNotifsGroupSup1 1.3.6.1.4.1.9.9.616.2.2.8
This collection of objects represent the mesh network related notifications sent by the agent to a network management station.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

ciscoLwappMeshConfigGroupSup2 1.3.6.1.4.1.9.9.616.2.2.9
This collection of objects represent the global and mesh node specific configuration and monitor parameters.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor