Nortel-MsCarrier-MscPassport-X25DteMIB

File: Nortel-MsCarrier-MscPassport-X25DteMIB.mib (155287 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs mscComponents
Counter32 DisplayString StorageType
RowStatus InterfaceIndex Gauge32
Integer32 Unsigned32 AsciiString
NonReplicated DigitString HexString
PassportCounter64 Link

Defined Types

MscX25DteRowStatusEntry  
SEQUENCE    
  mscX25DteRowStatus RowStatus
  mscX25DteComponentName DisplayString
  mscX25DteStorageType StorageType
  mscX25DteIndex Integer32

MscX25DteCidDataEntry  
SEQUENCE    
  mscX25DteCustomerIdentifier Unsigned32

MscX25DteIfEntry  
SEQUENCE    
  mscX25DteInterfaceMode INTEGER
  mscX25DteMaxActiveChannels Unsigned32
  mscX25DteNumberOfPLcn Unsigned32
  mscX25DtePacketSequencing INTEGER
  mscX25DteT20RestartTimer Unsigned32
  mscX25DteT21CallTimer Unsigned32
  mscX25DteT22ResetTimer Unsigned32
  mscX25DteT23ClearTimer Unsigned32

MscX25DteLcnCEntry  
SEQUENCE    
  mscX25DteLowestILChannelNumber Unsigned32
  mscX25DteHighestILChannelNumber Unsigned32
  mscX25DteLowestTLChannelNumber Unsigned32
  mscX25DteHighestTLChannelNumber Unsigned32
  mscX25DteLowestOLChannelNumber Unsigned32
  mscX25DteHighestOLChannelNumber Unsigned32

MscX25DteDcpEntry  
SEQUENCE    
  mscX25DteInPacketSize Unsigned32
  mscX25DteOutPacketSize Unsigned32
  mscX25DteInWindowSize Unsigned32
  mscX25DteOutWindowSize Unsigned32
  mscX25DteAcceptReverseCharging INTEGER
  mscX25DteProposeReverseCharging INTEGER
  mscX25DteOutThroughputClassSize INTEGER
  mscX25DteInThroughputClassSize INTEGER
  mscX25DteCugIndex AsciiString
  mscX25DteCugoaIndex AsciiString
  mscX25DteChargingInformation INTEGER
  mscX25DteRpoa AsciiString
  mscX25DteTrnstDlySlctnAInd Unsigned32
  mscX25DteCallingNetworkFax HexString
  mscX25DteCalledNetworkFax HexString
  mscX25DteCallUserData HexString

MscX25DteIfEntryEntry  
SEQUENCE    
  mscX25DteIfAdminStatus INTEGER
  mscX25DteIfIndex InterfaceIndex

MscX25DteStateEntry  
SEQUENCE    
  mscX25DteAdminState INTEGER
  mscX25DteOperationalState INTEGER
  mscX25DteUsageState INTEGER

MscX25DteOperStatusEntry  
SEQUENCE    
  mscX25DteSnmpOperStatus INTEGER

MscX25DteOpEntry  
SEQUENCE    
  mscX25DteInterfaceState INTEGER

MscX25DteStatsEntry  
SEQUENCE    
  mscX25DteInCalls Counter32
  mscX25DteInCallRefusals Counter32
  mscX25DteInPrvdrInitiatedClrs Counter32
  mscX25DteInRmtInitiatedRsts Counter32
  mscX25DteInPrvdrInitiatedRsts Counter32
  mscX25DteInRestarts Counter32
  mscX25DteInDataPackets Counter32
  mscX25DteInPktsAcusdOfPrtclErr Counter32
  mscX25DteInInterruptPackets Counter32
  mscX25DteOutCallAttempts Counter32
  mscX25DteOutCallFailures Counter32
  mscX25DteOutInterruptPackets Counter32
  mscX25DteOutDataPackets Counter32
  mscX25DteOutActiveChannels Counter32
  mscX25DteInActiveChannels Counter32
  mscX25DteTwowayActiveChannels Counter32
  mscX25DteT20RestartTimeouts Counter32
  mscX25DteT21CallTimeouts Counter32
  mscX25DteT22ResetTimeouts Counter32
  mscX25DteT23ClearTimeouts Counter32

MscX25DtePeerRowStatusEntry  
SEQUENCE    
  mscX25DtePeerRowStatus RowStatus
  mscX25DtePeerComponentName DisplayString
  mscX25DtePeerStorageType StorageType
  mscX25DtePeerIndex Integer32

MscX25DtePeerIfEntry  
SEQUENCE    
  mscX25DtePeerEncAddressType INTEGER
  mscX25DtePeerEncAddress AsciiString
  mscX25DtePeerX25Address DigitString
  mscX25DtePeerLinkToRemoteGroup Link

MscX25DtePeerCpEntry  
SEQUENCE    
  mscX25DtePeerInPacketSize Unsigned32
  mscX25DtePeerOutPacketSize Unsigned32
  mscX25DtePeerInWindowSize Unsigned32
  mscX25DtePeerOutWindowSize Unsigned32
  mscX25DtePeerAcceptReverseCharging INTEGER
  mscX25DtePeerProposeReverseCharging INTEGER
  mscX25DtePeerOutThroughputClassSize INTEGER
  mscX25DtePeerInThroughputClassSize INTEGER
  mscX25DtePeerCugIndex AsciiString
  mscX25DtePeerCugoaIndex AsciiString
  mscX25DtePeerNetworkUserIdentifier HexString
  mscX25DtePeerChargingInformation INTEGER
  mscX25DtePeerRpoa AsciiString
  mscX25DtePeerTrnstDlySlctnAInd Unsigned32
  mscX25DtePeerCallingNetworkFax HexString
  mscX25DtePeerCalledNetworkFax HexString
  mscX25DtePeerCallUserData HexString

MscX25DtePeerPEncEntry  
SEQUENCE    
  mscX25DtePeerPEncIndex Integer32
  mscX25DtePeerPEncValue INTEGER
  mscX25DtePeerPEncRowStatus RowStatus

MscX25DtePeerLcnEntry  
SEQUENCE    
  mscX25DtePeerLcnValue Integer32

MscX25DtePLcnRowStatusEntry  
SEQUENCE    
  mscX25DtePLcnRowStatus RowStatus
  mscX25DtePLcnComponentName DisplayString
  mscX25DtePLcnStorageType StorageType
  mscX25DtePLcnIndex Integer32

MscX25DtePLcnProvEntry  
SEQUENCE    
  mscX25DtePLcnEncAddressType INTEGER
  mscX25DtePLcnEncAddress AsciiString
  mscX25DtePLcnProtocolEncType INTEGER
  mscX25DtePLcnLinkToRemoteGroup Link
  mscX25DtePLcnInPacketSize Unsigned32
  mscX25DtePLcnOutPacketSize Unsigned32
  mscX25DtePLcnInWindowSize Unsigned32
  mscX25DtePLcnOutWindowSize Unsigned32

MscX25DteLcnRowStatusEntry  
SEQUENCE    
  mscX25DteLcnRowStatus RowStatus
  mscX25DteLcnComponentName DisplayString
  mscX25DteLcnStorageType StorageType
  mscX25DteLcnIndex Integer32

MscX25DteLcnStateEntry  
SEQUENCE    
  mscX25DteLcnAdminState INTEGER
  mscX25DteLcnOperationalState INTEGER
  mscX25DteLcnUsageState INTEGER

MscX25DteLcnCpEntry  
SEQUENCE    
  mscX25DteLcnInPacketSize Unsigned32
  mscX25DteLcnOutPacketSize Unsigned32
  mscX25DteLcnInWindowSize Unsigned32
  mscX25DteLcnOutWindowSize Unsigned32
  mscX25DteLcnProposeReverseCharging INTEGER
  mscX25DteLcnFastSelect INTEGER
  mscX25DteLcnOutThroughputClassSize INTEGER
  mscX25DteLcnInThroughputClassSize INTEGER
  mscX25DteLcnCugIndex AsciiString
  mscX25DteLcnCugoaIndex AsciiString
  mscX25DteLcnNetworkUserIdentifier HexString
  mscX25DteLcnChargingInformation INTEGER
  mscX25DteLcnRpoa AsciiString
  mscX25DteLcnTrnstDlySlctnAInd Unsigned32
  mscX25DteLcnCallingNetworkFax HexString
  mscX25DteLcnCalledNetworkFax HexString
  mscX25DteLcnCallUserData HexString

MscX25DteLcnLcnStatusEntry  
SEQUENCE    
  mscX25DteLcnStatus INTEGER
  mscX25DteLcnCallDirection INTEGER
  mscX25DteLcnCalledAddress DigitString
  mscX25DteLcnCallingAddress DigitString
  mscX25DteLcnOriginalCalledAddress DigitString

MscX25DteLcnStatsEntry  
SEQUENCE    
  mscX25DteLcnInUknownProtocols Counter32
  mscX25DteLcnInDataOctets Counter32
  mscX25DteLcnInDataPackets Counter32
  mscX25DteLcnInRmtInitiatedRsts Counter32
  mscX25DteLcnInPrvdrInitiatedRsts Counter32
  mscX25DteLcnInInterruptPackets Counter32
  mscX25DteLcnOutDataOctets Counter32
  mscX25DteLcnOutDataPackets Counter32
  mscX25DteLcnOutInterruptPackets Counter32
  mscX25DteLcnT22ResetTimeouts Counter32

MscX25DteLapbRowStatusEntry  
SEQUENCE    
  mscX25DteLapbRowStatus RowStatus
  mscX25DteLapbComponentName DisplayString
  mscX25DteLapbStorageType StorageType
  mscX25DteLapbIndex NonReplicated

MscX25DteLapbCpEntry  
SEQUENCE    
  mscX25DteLapbStationType INTEGER
  mscX25DteLapbFrameSequencing INTEGER
  mscX25DteLapbN1FrameSize Unsigned32
  mscX25DteLapbKWindowSize Unsigned32
  mscX25DteLapbN2TransmitLimit Unsigned32
  mscX25DteLapbT1AckTimer Unsigned32
  mscX25DteLapbT2AckDelayTimer Unsigned32
  mscX25DteLapbT4IdleProbeTimer Unsigned32
  mscX25DteLapbActionInitiate INTEGER
  mscX25DteLapbActionRecvDM INTEGER
  mscX25DteLapbTxQDegradeThreshold Unsigned32
  mscX25DteLapbTxQResetThreshold Unsigned32

MscX25DteLapbStateEntry  
SEQUENCE    
  mscX25DteLapbAdminState INTEGER
  mscX25DteLapbOperationalState INTEGER
  mscX25DteLapbUsageState INTEGER

MscX25DteLapbStatusEntry  
SEQUENCE    
  mscX25DteLapbCurrentState INTEGER
  mscX25DteLapbLastStateChangeReason INTEGER
  mscX25DteLapbFrmrTransmit HexString
  mscX25DteLapbFrmrReceive HexString
  mscX25DteLapbCurrentQueueSize Unsigned32

MscX25DteLapbStatsEntry  
SEQUENCE    
  mscX25DteLapbStateChanges Counter32
  mscX25DteLapbRemoteBusy Counter32
  mscX25DteLapbTransmitRejectFrames Counter32
  mscX25DteLapbReceiveRejectFrames Counter32
  mscX25DteLapbT1AckTimeout Counter32

MscX25DteLapbFramerRowStatusEntry  
SEQUENCE    
  mscX25DteLapbFramerRowStatus RowStatus
  mscX25DteLapbFramerComponentName DisplayString
  mscX25DteLapbFramerStorageType StorageType
  mscX25DteLapbFramerIndex NonReplicated

MscX25DteLapbFramerProvEntry  
SEQUENCE    
  mscX25DteLapbFramerInterfaceName Link

MscX25DteLapbFramerLinkEntry  
SEQUENCE    
  mscX25DteLapbFramerFlagsBetweenFrames Unsigned32

MscX25DteLapbFramerStateEntry  
SEQUENCE    
  mscX25DteLapbFramerAdminState INTEGER
  mscX25DteLapbFramerOperationalState INTEGER
  mscX25DteLapbFramerUsageState INTEGER

MscX25DteLapbFramerStatsEntry  
SEQUENCE    
  mscX25DteLapbFramerFrmToIf Counter32
  mscX25DteLapbFramerFrmFromIf Counter32
  mscX25DteLapbFramerOctetFromIf Counter32
  mscX25DteLapbFramerAborts Counter32
  mscX25DteLapbFramerCrcErrors Counter32
  mscX25DteLapbFramerLrcErrors Counter32
  mscX25DteLapbFramerNonOctetErrors Counter32
  mscX25DteLapbFramerOverruns Counter32
  mscX25DteLapbFramerUnderruns Counter32
  mscX25DteLapbFramerFrmToIf64 PassportCounter64
  mscX25DteLapbFramerFrmFromIf64 PassportCounter64
  mscX25DteLapbFramerOctetFromIf64 PassportCounter64

MscX25DteLapbFramerUtilEntry  
SEQUENCE    
  mscX25DteLapbFramerNormPrioLinkUtilToIf Gauge32
  mscX25DteLapbFramerNormPrioLinkUtilFromIf Gauge32

MscX25DtePleRowStatusEntry  
SEQUENCE    
  mscX25DtePleRowStatus RowStatus
  mscX25DtePleComponentName DisplayString
  mscX25DtePleStorageType StorageType
  mscX25DtePleIndex NonReplicated

MscX25DtePleProvEntry  
SEQUENCE    
  mscX25DtePleInactivityTimer Unsigned32

MscX25DtePleOpEntry  
SEQUENCE    
  mscX25DtePleEncAddrToX25LkupFlrs Unsigned32
  mscX25DtePleLastFailedEncAddr HexString
  mscX25DtePleX25AddrToEncLkupFlrs Unsigned32
  mscX25DtePleLastFailedX25Addr DigitString

MscX25DteRgRowStatusEntry  
SEQUENCE    
  mscX25DteRgRowStatus RowStatus
  mscX25DteRgComponentName DisplayString
  mscX25DteRgStorageType StorageType
  mscX25DteRgIndex Integer32

MscX25DteRgIfEntryEntry  
SEQUENCE    
  mscX25DteRgIfAdminStatus INTEGER
  mscX25DteRgIfIndex InterfaceIndex

MscX25DteRgProvEntry  
SEQUENCE    
  mscX25DteRgLinkToProtocolPort Link
  mscX25DteRgLocalAddress DigitString
  mscX25DteRgMtuSize Unsigned32

MscX25DteRgStateEntry  
SEQUENCE    
  mscX25DteRgAdminState INTEGER
  mscX25DteRgOperationalState INTEGER
  mscX25DteRgUsageState INTEGER

MscX25DteRgOperStatusEntry  
SEQUENCE    
  mscX25DteRgSnmpOperStatus INTEGER

MscX25DteRgLTPlcnEntry  
SEQUENCE    
  mscX25DteRgLTPlcnValue Link
  mscX25DteRgLTPlcnRowStatus RowStatus

MscX25DteRgLtPeerEntry  
SEQUENCE    
  mscX25DteRgLtPeerValue Link
  mscX25DteRgLtPeerRowStatus RowStatus

MscX25DteRgLcnEntry  
SEQUENCE    
  mscX25DteRgLcnValue Integer32

Defined Values

x25DteMIB 1.3.6.1.4.1.562.36.2.2.48
OBJECT IDENTIFIER    

mscX25Dte 1.3.6.1.4.1.562.36.2.1.90
OBJECT IDENTIFIER    

mscX25DteRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.1
This entry controls the addition and deletion of mscX25Dte components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRowStatusEntry

mscX25DteRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.1.1
A single entry in the table represents a single mscX25Dte component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRowStatusEntry  

mscX25DteRowStatus 1.3.6.1.4.1.562.36.2.1.90.1.1.1
This variable is used as the basis for SNMP naming of mscX25Dte components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscX25DteComponentName 1.3.6.1.4.1.562.36.2.1.90.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DteStorageType 1.3.6.1.4.1.562.36.2.1.90.1.1.4
This variable represents the storage type value for the mscX25Dte tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DteIndex 1.3.6.1.4.1.562.36.2.1.90.1.1.10
This variable represents the index for the mscX25Dte tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

mscX25DteCidDataTable 1.3.6.1.4.1.562.36.2.1.90.20
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteCidDataEntry

mscX25DteCidDataEntry 1.3.6.1.4.1.562.36.2.1.90.20.1
An entry in the mscX25DteCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteCidDataEntry  

mscX25DteCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.90.20.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscX25DteIfTable 1.3.6.1.4.1.562.36.2.1.90.21
This group provides the administrative set of parameters for the X.25 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteIfEntry

mscX25DteIfEntry 1.3.6.1.4.1.562.36.2.1.90.21.1
An entry in the mscX25DteIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteIfEntry  

mscX25DteInterfaceMode 1.3.6.1.4.1.562.36.2.1.90.21.1.1
This attribute specifies the packet mode in which the X.25 interface operates. When this attribute is set to dte, interface on the other side of the physical link must be configured as a dce.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dte(1), dce(2)  

mscX25DteMaxActiveChannels 1.3.6.1.4.1.562.36.2.1.90.21.1.2
This attribute specifies the maximum number of channels that can be active on this interface including the Permanent Lcns and the Switched Lcns. In total maxActiveChannel will determine the maximum number of Lcn components which may exist at a given time. This should be set to a value greater or equal to the numberOfPLcn provisioned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteNumberOfPLcn 1.3.6.1.4.1.562.36.2.1.90.21.1.3
This attribute specifies the number of Permanent Logical Channels that are supported on this X.25 interface (that is, the number of PermLcn components that may be provisioned at this interface). The PermLcn components use channel numbers starting from 1 and up to lowestILChannelNumber. A value of 0 for this attribute indicates that no Permanent Logical channels are supported on this X.25 interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DtePacketSequencing 1.3.6.1.4.1.562.36.2.1.90.21.1.4
This attribute specifies the sequence numbering of packets for the X.25 interface. The value of this attribute must be the same as the packet sequencing configured at the X.25 interface on the other side of the physical link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER modulo8(1), modulo128(2)  

mscX25DteT20RestartTimer 1.3.6.1.4.1.562.36.2.1.90.21.1.5
This attribute provides the period in milliseconds within which a restart request packet should be confirmed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65536000  

mscX25DteT21CallTimer 1.3.6.1.4.1.562.36.2.1.90.21.1.6
This attribute provides the period in milliseconds within which a call request packet should be confirmed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65536000  

mscX25DteT22ResetTimer 1.3.6.1.4.1.562.36.2.1.90.21.1.7
This attribute provides the period in milliseconds within which a reset request packet should be confirmed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65536000  

mscX25DteT23ClearTimer 1.3.6.1.4.1.562.36.2.1.90.21.1.8
This attribute provides the period in milliseconds within which a clear request packet should be confirmed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65536000  

mscX25DteLcnCTable 1.3.6.1.4.1.562.36.2.1.90.22
This group contains the provisionable attributes for the Logical Channel configuration of the X.25 Interface. The logical channel range table is ordered as follows: Permanent Logical Channels(PLC), One-way Incoming Channels (IC), Two-way Channels(TC) and One-way Outgoing Channels (OC), in a consecutive manner.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnCEntry

mscX25DteLcnCEntry 1.3.6.1.4.1.562.36.2.1.90.22.1
An entry in the mscX25DteLcnCTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnCEntry  

mscX25DteLowestILChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.1
This attribute specifies the lowest Lcn number of the One-way Incoming Channel range for this X.25 interface. The value for this attribute must be greater than the numberOfPLcn attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteHighestILChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.2
This attribute specifies the highest Lcn number of the One-way Incoming Channel range for this X.25 interface. A value of 0 indicates that there are no channels in this range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteLowestTLChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.3
This attribute specifies the lowest Lcn number of the Two-way Channel range for this X.25 interface. The value for this attribute must be greater than the highestILChannelNumber attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteHighestTLChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.4
This attribute specifies the highest Lcn number of the Two-way Channel range for this X.25 interface. A value of 0 indicates that there are no channels in this range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteLowestOLChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.5
This attribute specifies the lowest Lcn number of the One-way Outgoing Channel range for this X.25 interface. The value for this attribute must be greater than the highestTLChannelNumber attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteHighestOLChannelNumber 1.3.6.1.4.1.562.36.2.1.90.22.1.6
This attribute specifies the highest Lcn number of the One-way Outgoing Channel range for this X.25 interface. A value of 0 indicates that there are no channels in this range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

mscX25DteDcpTable 1.3.6.1.4.1.562.36.2.1.90.23
This group contains the provisionable attributes giving the default call parameters used by all the logical channels during call setup. It is possible that different default call parameters will be used for a particular call, based on the Peer component for the given call. The actual call parameters operational for a given call are found in the Lcn component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteDcpEntry

mscX25DteDcpEntry 1.3.6.1.4.1.562.36.2.1.90.23.1
An entry in the mscX25DteDcpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteDcpEntry  

mscX25DteInPacketSize 1.3.6.1.4.1.562.36.2.1.90.23.1.1
This attribute specifies the maximum receive packet size in octets for the X.25 interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DteOutPacketSize 1.3.6.1.4.1.562.36.2.1.90.23.1.2
This attribute specifies the maximum transmit packet size in octets for the X.25 interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DteInWindowSize 1.3.6.1.4.1.562.36.2.1.90.23.1.3
This attribute specifies the maximum receive window size for the X.25 interface. A window size greater than 7 is only valid when the packetSequencing attribute is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteOutWindowSize 1.3.6.1.4.1.562.36.2.1.90.23.1.4
This attribute specifies the maximum transmit window size for the X.25 interface. A window size greater than 7 is only valid when the packetSequencing is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteAcceptReverseCharging 1.3.6.1.4.1.562.36.2.1.90.23.1.5
This attribute specifies whether local end will accept or refuse charges for a call. A value of neverAccept is only used at the X.25 interface level and indicates that this interface will never accept reverse charging (that is no Peer component can override this parameter, allowing reverse charged calls to be accepted).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER accept(2), refuse(3), neverAccept(4)  

mscX25DteProposeReverseCharging 1.3.6.1.4.1.562.36.2.1.90.23.1.6
This attribute specifies whether local/reverse charging is signalled in the call request packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reverse(2), local(3)  

mscX25DteOutThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.23.1.8
This attribute specifies the value of the transmit throughput class to be negotiated. A value of notSpecified means the facility is not signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17)  

mscX25DteInThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.23.1.9
This attribute specifies the value of the receive throughput class to be negotiated. A value of notSpecified means the facility is not signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17)  

mscX25DteCugIndex 1.3.6.1.4.1.562.36.2.1.90.23.1.10
This attribute specifies the index of the Closed User Group facility to signal. The index consists of two or four octets each representing a digit in the range of 0 to 9. A value of null (empty string) at the X.25 interface means no CUG facility is signalled. If a cugIndex is provisioned to be signalled, the cugoaIndex attribute must be null.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DteCugoaIndex 1.3.6.1.4.1.562.36.2.1.90.23.1.11
This attribute specifies the index of the Close User Group with Outgoing Access facility to signal. The index consists of two or four octets each representing a digit in the range of 0 to 9. A value of null (empty string) at the X.25 interface means no CUGOA facility is signalled. If a cugoaIndex is provisioned to be signalled, the cugIndex attribute must be null.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DteChargingInformation 1.3.6.1.4.1.562.36.2.1.90.23.1.13
This attribute specifies whether the charging information facility is to be signalled in a call request packet. A value of notSpecified means the facility is not signalled. A value of notRequested means the facility is signalled but charging information is not requested (that is, the charging info field of the facility is set Off). A value of requested means the facility is signalled to explicitly request charging information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notSpecified(2), notRequested(3), requested(4)  

mscX25DteRpoa 1.3.6.1.4.1.562.36.2.1.90.23.1.14
This attribute specifies the value of the RPOA facility to signal in a call request packet. The value of null (empty string) at the X.25 interface means no RPOA facility is signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..108)  

mscX25DteTrnstDlySlctnAInd 1.3.6.1.4.1.562.36.2.1.90.23.1.15
This attribute specifies the value of the Transit Delay Selection and Indication facility to signal in a call request packet. A value of 65536 at the X.25 interface level means no TDSAI facility is signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65536  

mscX25DteCallingNetworkFax 1.3.6.1.4.1.562.36.2.1.90.23.1.24
This attribute specifies the Calling Network facilities to be signalled in a call request packet. A value of null (empty string) at the X.25 interface means no facilities are signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DteCalledNetworkFax 1.3.6.1.4.1.562.36.2.1.90.23.1.25
This attribute specifies the called network facilities to be signalled in a call request packet. A value of null (empty string) at the X.25 interface means no facilities are signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DteCallUserData 1.3.6.1.4.1.562.36.2.1.90.23.1.26
This attribute specifies the user data to be signalled in the call request packet. A value of null (empty string) means no user data is signalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..128)  

mscX25DteIfEntryTable 1.3.6.1.4.1.562.36.2.1.90.24
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteIfEntryEntry

mscX25DteIfEntryEntry 1.3.6.1.4.1.562.36.2.1.90.24.1
An entry in the mscX25DteIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteIfEntryEntry  

mscX25DteIfAdminStatus 1.3.6.1.4.1.562.36.2.1.90.24.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscX25DteIfIndex 1.3.6.1.4.1.562.36.2.1.90.24.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscX25DteStateTable 1.3.6.1.4.1.562.36.2.1.90.25
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteStateEntry

mscX25DteStateEntry 1.3.6.1.4.1.562.36.2.1.90.25.1
An entry in the mscX25DteStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteStateEntry  

mscX25DteAdminState 1.3.6.1.4.1.562.36.2.1.90.25.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscX25DteOperationalState 1.3.6.1.4.1.562.36.2.1.90.25.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscX25DteUsageState 1.3.6.1.4.1.562.36.2.1.90.25.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscX25DteOperStatusTable 1.3.6.1.4.1.562.36.2.1.90.26
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteOperStatusEntry

mscX25DteOperStatusEntry 1.3.6.1.4.1.562.36.2.1.90.26.1
An entry in the mscX25DteOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteOperStatusEntry  

mscX25DteSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.90.26.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscX25DteOpTable 1.3.6.1.4.1.562.36.2.1.90.27
This group contains the operational status of the X.25 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteOpEntry

mscX25DteOpEntry 1.3.6.1.4.1.562.36.2.1.90.27.1
An entry in the mscX25DteOpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteOpEntry  

mscX25DteInterfaceState 1.3.6.1.4.1.562.36.2.1.90.27.1.1
This attribute specifies the state of the interface. The notReady state, is the initial state of the service, when it is being initialized. The localRestarting state is entered when a Restart packet is sent to the link and the interface is waiting for a response. The remoteRestarting state is entered when a Restart packet is received from the link, and is being processed. In ready state, the service is operational and ready to provide service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notReady(0), localRestarting(1), remoteRestarting(2), ready(3)  

mscX25DteStatsTable 1.3.6.1.4.1.562.36.2.1.90.28
This component contains the statistics for the X.25 interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteStatsEntry

mscX25DteStatsEntry 1.3.6.1.4.1.562.36.2.1.90.28.1
An entry in the mscX25DteStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteStatsEntry  

mscX25DteInCalls 1.3.6.1.4.1.562.36.2.1.90.28.1.1
This attribute counts the number of call packets received from link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInCallRefusals 1.3.6.1.4.1.562.36.2.1.90.28.1.2
This attribute counts the number of calls received from the link which have been cleared. This includes calls cleared by the X.25 interface and calls cleared by the higher level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInPrvdrInitiatedClrs 1.3.6.1.4.1.562.36.2.1.90.28.1.3
This attribute counts the number of clear packets received from the link with a cause code other than DTE initiated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInRmtInitiatedRsts 1.3.6.1.4.1.562.36.2.1.90.28.1.4
This attribute counts the number of reset packets received from the link with the cause code DTE initiated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInPrvdrInitiatedRsts 1.3.6.1.4.1.562.36.2.1.90.28.1.5
This attribute counts the number of reset packets received from the link with the cause code other than DTE initiated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInRestarts 1.3.6.1.4.1.562.36.2.1.90.28.1.6
This attribute counts the number of restart packets received from the link while the service is in ready state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInDataPackets 1.3.6.1.4.1.562.36.2.1.90.28.1.7
This attribute counts the number of data packets received from link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInPktsAcusdOfPrtclErr 1.3.6.1.4.1.562.36.2.1.90.28.1.8
This attribute counts the number of clear, reset, restart and diagnostic packets received from link containing a procedure error cause code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInInterruptPackets 1.3.6.1.4.1.562.36.2.1.90.28.1.9
This attributes counts the number of interrupt packets received from link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteOutCallAttempts 1.3.6.1.4.1.562.36.2.1.90.28.1.10
This attribute counts the number of call packets sent from this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteOutCallFailures 1.3.6.1.4.1.562.36.2.1.90.28.1.11
This attribute counts the number of call attempts from this interface that failed. This includes calls that were cleared because of restrictive fast select.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteOutInterruptPackets 1.3.6.1.4.1.562.36.2.1.90.28.1.12
This attribute counts the number of interrupt packets sent to the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteOutDataPackets 1.3.6.1.4.1.562.36.2.1.90.28.1.13
This attribute counts the number of data packets sent to the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteOutActiveChannels 1.3.6.1.4.1.562.36.2.1.90.28.1.14
This attribute indicates the number of One-way Outgoing Channels that are currently in use. This counter includes the call requests that have not been accepted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteInActiveChannels 1.3.6.1.4.1.562.36.2.1.90.28.1.15
This attribute indicates number of One-way Incoming Channels that are currently active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteTwowayActiveChannels 1.3.6.1.4.1.562.36.2.1.90.28.1.16
This attribute indicates the number of Two-way Channels that are in use. This includes call requests sent but not yet accepted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteT20RestartTimeouts 1.3.6.1.4.1.562.36.2.1.90.28.1.17
This attribute counts the number of times the T20 restart timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteT21CallTimeouts 1.3.6.1.4.1.562.36.2.1.90.28.1.18
This attribute counts the number of times the T21 call timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteT22ResetTimeouts 1.3.6.1.4.1.562.36.2.1.90.28.1.19
This attribute counts the number of times the T22 reset timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteT23ClearTimeouts 1.3.6.1.4.1.562.36.2.1.90.28.1.20
This attribute counts the number of times the T23 clear timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DtePeer 1.3.6.1.4.1.562.36.2.1.90.2
OBJECT IDENTIFIER    

mscX25DtePeerRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.2.1
This entry controls the addition and deletion of mscX25DtePeer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePeerRowStatusEntry

mscX25DtePeerRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.2.1.1
A single entry in the table represents a single mscX25DtePeer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePeerRowStatusEntry  

mscX25DtePeerRowStatus 1.3.6.1.4.1.562.36.2.1.90.2.1.1.1
This variable is used as the basis for SNMP naming of mscX25DtePeer components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscX25DtePeerComponentName 1.3.6.1.4.1.562.36.2.1.90.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DtePeerStorageType 1.3.6.1.4.1.562.36.2.1.90.2.1.1.4
This variable represents the storage type value for the mscX25DtePeer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DtePeerIndex 1.3.6.1.4.1.562.36.2.1.90.2.1.1.10
This variable represents the index for the mscX25DtePeer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4095  

mscX25DtePeerIfTable 1.3.6.1.4.1.562.36.2.1.90.2.10
This group provides the administrative set of parameters for the Peer interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePeerIfEntry

mscX25DtePeerIfEntry 1.3.6.1.4.1.562.36.2.1.90.2.10.1
An entry in the mscX25DtePeerIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePeerIfEntry  

mscX25DtePeerEncAddressType 1.3.6.1.4.1.562.36.2.1.90.2.10.1.1
This attribute specifies the encapsulation type for the address of the remote host with which this Peer component allows communication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(204)  

mscX25DtePeerEncAddress 1.3.6.1.4.1.562.36.2.1.90.2.10.1.2
This attribute specifies the encapsulation address of the remote host with which this Peer component allows communication. This address must correspond with the encapsulation address type. Thus in the case of IP, it will contain a IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..128)  

mscX25DtePeerX25Address 1.3.6.1.4.1.562.36.2.1.90.2.10.1.3
This attribute specifies the X.25 address that identifies the remote host with which this Peer component allows communication. The remote X.25 interface could be subdivided through the use of RemoteGroup components; in which case this x25Address is the X.25 address of the destination's RemoteGroup (not to be confused with the RemoteGroup indicated by the linkToRemoteGroup attribute of THIS Peer component).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(1..15)  

mscX25DtePeerLinkToRemoteGroup 1.3.6.1.4.1.562.36.2.1.90.2.10.1.4
This is a link to a RemoteGroup component. The RemoteGroup components logically divide up the X.25 Interface such that a number of Protocol Ports (and consequently a number of Virtual Routers) may share the same X.25 Interface into a Wide Area Network. In particular, the remote host identified by this Peer component is designated as belonging to the RemoteGroup linked by this attribute. The set of all Peer components and PermLcn components which link to a given RemoteGroup determine the subset of remote hosts which are accessible to a particular Protocol Port (and ultimately a Virtual Router).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DtePeerCpTable 1.3.6.1.4.1.562.36.2.1.90.2.12
This group contains the call parameters used to establish a call to/ from the remote host identified by this Peer component
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePeerCpEntry

mscX25DtePeerCpEntry 1.3.6.1.4.1.562.36.2.1.90.2.12.1
An entry in the mscX25DtePeerCpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePeerCpEntry  

mscX25DtePeerInPacketSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.1
This attribute specifies the default maximum receive packet size in octets. A setting of 0 indicates the inPacketSize setting for the X.25 interface (in X25Dte component) is used during call setup to the remote host identified by this Peer component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DtePeerOutPacketSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.2
This attribute specifies the default maximum transmit packet size in octets. A setting of 0 indicates the outPacketSize setting for the X.25 interface (in the X25Dte component) is used during call setup to the remote host identified by this Peer component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DtePeerInWindowSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.3
This attribute specifies the default receive window size. A window size of 0 indicates the inWindowSize setting for the X.25 interface (in the X25Dte component) is used during call setup to the remote host identified by this Peer component. A window size greater than 7 is only valid when the packetSequencing attribute of the X25Dte component is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..127  

mscX25DtePeerOutWindowSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.4
This attribute specifies the default transmit window size. A window size of 0 indicates the outWindowSize setting for the X.25 interface is used during call setup to the Peer identified by this component. A window size greater than 7 is only valid when the packetSequencing attribute of the X25Dte component is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..127  

mscX25DtePeerAcceptReverseCharging 1.3.6.1.4.1.562.36.2.1.90.2.12.1.5
This attribute specifies whether the local end will accept or refuse charges for a call from the remote host identified by this Peer component. A value of default indicates the use of the acceptReverseCharging value from the X25Dte component. If the value at the X25Dte level is neverAccept, a value of accept in this Peer component will be ignored because no reverse charge calls are to be accepted by this X.25 Dte.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), accept(2), refuse(3)  

mscX25DtePeerProposeReverseCharging 1.3.6.1.4.1.562.36.2.1.90.2.12.1.6
This attribute specifies whether local/reverse charging is signalled in a call request packet. A value of default indicates the use of the value from the proposeReverseCharging attribute of the X25Dte component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), reverse(2), local(3)  

mscX25DtePeerOutThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.8
This attribute specifies the value of the transmit throughput class to be negotiated. A value of default indicates the use of the value from the outThroughputClassSize attribute of the X25Dte component. A value of notSpecified means the facility is not signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17), default(18)  

mscX25DtePeerInThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.2.12.1.9
This attribute specifies the value of the receive throughput class to be negotiated. A value of default indicates the use of the value from the inThroughputClassSize attribute of the X25Dte component. A value of notSpecified means the facility is not signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17), default(18)  

mscX25DtePeerCugIndex 1.3.6.1.4.1.562.36.2.1.90.2.12.1.10
This attribute specifies the index of the Closed User Group facility to signal. A value of 'DEF' indicates the use of the value from the cugIndex attribute of the X25Dte component. A value of null (empty string) indicates no CUG facility is to be signalled. If a cugIndex is provisioned to be signalled, the cugoaIndex attribute must be null.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DtePeerCugoaIndex 1.3.6.1.4.1.562.36.2.1.90.2.12.1.11
This attribute specifies the index of the Closed User Group with Outgoing Access facility to signal. A value of 'DEF' indicates the use of the value from the cugoaIndex attribute of the X25Dte component. A value of null (empty string) indicates no CUGOA facility is to be signalled. If a cugoaIndex is provisioned to be signalled, the cugIndex attribute must be null.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DtePeerNetworkUserIdentifier 1.3.6.1.4.1.562.36.2.1.90.2.12.1.12
This attribute specifies the Network User Identifier facility to signal. A value of null (empty string) indicates no NUI facility is to be signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DtePeerChargingInformation 1.3.6.1.4.1.562.36.2.1.90.2.12.1.13
This attribute specifies whether the charging information facility is signalled in the call request packet. A value of default indicates the use of the value from the chargingInformation attribute of the X25Dte component. A value of notSpecified means the facility is not signalled. A value of notRequested means the facility is signalled but charging information is not requested (that is, the charging info field of the facility is set Off). A value of requested means the facility is signalled to explicitly request charging information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), notSpecified(2), notRequested(3), requested(4)  

mscX25DtePeerRpoa 1.3.6.1.4.1.562.36.2.1.90.2.12.1.14
This attribute specifies the RPOA facility to signal in a call request packet. A value of 'DEF' indicates the use of the value from the rpoa attribute of the X25Dte component. A value of null (empty string) indicates no RPOA facility is to be signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..108)  

mscX25DtePeerTrnstDlySlctnAInd 1.3.6.1.4.1.562.36.2.1.90.2.12.1.15
This attribute specifies the value of the Transit Delay Selection and Indication facility to signal in a call request packet. A value of 65536 indicates no facility is signalled. A value of 65537 indicates the use of the value from the trnstDlySlctnAInd attribute of the X25Dte component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65537  

mscX25DtePeerCallingNetworkFax 1.3.6.1.4.1.562.36.2.1.90.2.12.1.24
This attribute specifies the Calling Network facilities to signal in a call request packet. The facilities are encoded here exactly as they are encoded in the call packet. These facilities do not include the marker facility code. A value of null (empty string) indicates the callingNetworkFax from the X25Dte are to be signalled. If that value is also null, no Calling Network Facilities are signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DtePeerCalledNetworkFax 1.3.6.1.4.1.562.36.2.1.90.2.12.1.25
This attribute specifies the Called Network facilities to signal in a call request packet. The facilities are encoded here exactly as they are encoded in the call packet. These facilities do not include the marker facility code. A value of null (empty string) indicates the calledNetworkFax from the X25Dte are to be signalled. If that value is also null, no Called Network Facilities are signalled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DtePeerCallUserData 1.3.6.1.4.1.562.36.2.1.90.2.12.1.26
This attribute specifies the user data to signal in a call request packet. A value of null (empty string) indicates that the callUserData from the X25Dte is to be signalled. If callUserData of the X25Dte component is also null and protocolEncType of this Peer has the value IP, H.CC will be signalled as the call user data of a call request packet. Thus for IP encapsulation according to RFC1356, both the callUserData from the Peer and X25Dte components must be null and the protocolEncType set to IP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..128)  

mscX25DtePeerPEncTable 1.3.6.1.4.1.562.36.2.1.90.2.208
Each instance of this replicated attribute describes an encapsulation method permitted for encapsulating the protocol data units (PDUs) of an upper layer protocol when communicating with the remote host identified by this Peer component. The index of a given replicated instance of this attribute represents the relative priority of the encapsulation method specified by the given attribute instance. An attribute with index '1' has the highest priority, so the encapsulation method described by it will be the first one attempted when signalling a call to the link. If the protocolEncType is set to IP to encapsulate IP traffic according to RFC1356, the callUserData for this Peer component and the X25Dte component must both be null, so that H.CC will be signalled as the call user data of the call request. This indicates that the protocol encapsulation type of IP is to be used for the channel. A call received from the link will be accepted as long as the encapsulation method indicated in the call user data of the incoming call packet is included in one of these replicated attributes. (This presupposes that the incoming call has been directed to the RemoteGroup to which this Peer is linked through the linkToRemoteGroup attribute.)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePeerPEncEntry

mscX25DtePeerPEncEntry 1.3.6.1.4.1.562.36.2.1.90.2.208.1
An entry in the mscX25DtePeerPEncTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePeerPEncEntry  

mscX25DtePeerPEncIndex 1.3.6.1.4.1.562.36.2.1.90.2.208.1.1
This variable represents the index for the mscX25DtePeerPEncTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1  

mscX25DtePeerPEncValue 1.3.6.1.4.1.562.36.2.1.90.2.208.1.2
This variable represents an individual value for the mscX25DtePeerPEncTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(204)  

mscX25DtePeerPEncRowStatus 1.3.6.1.4.1.562.36.2.1.90.2.208.1.3
This variable is used to control the addition and deletion of individual values of the mscX25DtePeerPEncTable.
Status: mandatory Access: write-only
OBJECT-TYPE    
  RowStatus  

mscX25DtePeerLcnTable 1.3.6.1.4.1.562.36.2.1.90.2.209
This attribute specifies the local logical channel numbers (Lcn) in use for the X.25 calls to the remote host identified by this Peer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePeerLcnEntry

mscX25DtePeerLcnEntry 1.3.6.1.4.1.562.36.2.1.90.2.209.1
An entry in the mscX25DtePeerLcnTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePeerLcnEntry  

mscX25DtePeerLcnValue 1.3.6.1.4.1.562.36.2.1.90.2.209.1.1
This variable represents both the value and the index for the mscX25DtePeerLcnTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32 1..4095  

mscX25DtePLcn 1.3.6.1.4.1.562.36.2.1.90.3
OBJECT IDENTIFIER    

mscX25DtePLcnRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.3.1
This entry controls the addition and deletion of mscX25DtePLcn components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePLcnRowStatusEntry

mscX25DtePLcnRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.3.1.1
A single entry in the table represents a single mscX25DtePLcn component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePLcnRowStatusEntry  

mscX25DtePLcnRowStatus 1.3.6.1.4.1.562.36.2.1.90.3.1.1.1
This variable is used as the basis for SNMP naming of mscX25DtePLcn components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscX25DtePLcnComponentName 1.3.6.1.4.1.562.36.2.1.90.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DtePLcnStorageType 1.3.6.1.4.1.562.36.2.1.90.3.1.1.4
This variable represents the storage type value for the mscX25DtePLcn tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DtePLcnIndex 1.3.6.1.4.1.562.36.2.1.90.3.1.1.10
This variable represents the index for the mscX25DtePLcn tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4095  

mscX25DtePLcnProvTable 1.3.6.1.4.1.562.36.2.1.90.3.10
This group contains the provisionable parameters for the permanent logical channels (PLcns) on the X.25 interface (corresponding to Permanent Virtual Circuits (PVCs) provisioned on the Wide Area Network).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePLcnProvEntry

mscX25DtePLcnProvEntry 1.3.6.1.4.1.562.36.2.1.90.3.10.1
An entry in the mscX25DtePLcnProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePLcnProvEntry  

mscX25DtePLcnEncAddressType 1.3.6.1.4.1.562.36.2.1.90.3.10.1.1
This attribute specifies the encapsulation type for the address of the remote host with which this Peer component allows communication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), ip(204)  

mscX25DtePLcnEncAddress 1.3.6.1.4.1.562.36.2.1.90.3.10.1.2
This attribute specifies the encapsulation address of the remote host with which this PermLcn component defines a connection
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..128)  

mscX25DtePLcnProtocolEncType 1.3.6.1.4.1.562.36.2.1.90.3.10.1.3
This attribute specifies the encapsulation method to use when exchanging protocol data units (PDUs) over this channel. IP and Null protocolEncTypes are as defined in RFC1356. NscNull is an encapsulation method for carrying IP datagrams which requires removing 3 padding octets of zeroes and the protocol identifier H.CC from the front of each data packet received from the link in order to obtain the PDU. PDUs sent to the link are propounded by a the protocol identifier H.CC. NscNull should only be set when the remote host is following this same encapsulation method.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER null(0), ip(204), nscNull(257)  

mscX25DtePLcnLinkToRemoteGroup 1.3.6.1.4.1.562.36.2.1.90.3.10.1.4
This attribute specifies the link to the RemoteGroup, indicating the RemoteGroup component with which this PermLcn component is associated. The RemoteGroup components logically divide up the X.25 Interface such that a number of Protocol Ports (and consequently a number of Virtual Routers) may share the same X.25 Interface into a Wide Area Network. In particular, the remote host identified by this PermLcn component is designated as belonging to the RemoteGroup linked by this attribute. The set of all PermLcn and Peer components which link to a given RemoteGroup determine the subset of remote hosts which are accessible to a particular Protocol Port (and ultimately a Virtual Router).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DtePLcnInPacketSize 1.3.6.1.4.1.562.36.2.1.90.3.10.1.5
This attribute specifies the maximum receive packet size in octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DtePLcnOutPacketSize 1.3.6.1.4.1.562.36.2.1.90.3.10.1.6
This attribute specifies the maximum transmit packet size in octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DtePLcnInWindowSize 1.3.6.1.4.1.562.36.2.1.90.3.10.1.7
This attribute specifies the maximum receive window size. A inWindowSize greater than 7 is only valid when the packetSequencing attribute of the X25Dte component is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DtePLcnOutWindowSize 1.3.6.1.4.1.562.36.2.1.90.3.10.1.8
This attribute specifies the maximum transmit window size. A outWindowSize greater than 7 is only valid when the packetSequencing attribute of the X25Dte component is set to modulo128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteLcn 1.3.6.1.4.1.562.36.2.1.90.4
OBJECT IDENTIFIER    

mscX25DteLcnRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.4.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mscX25DteLcn components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnRowStatusEntry

mscX25DteLcnRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.4.1.1
A single entry in the table represents a single mscX25DteLcn component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnRowStatusEntry  

mscX25DteLcnRowStatus 1.3.6.1.4.1.562.36.2.1.90.4.1.1.1
This variable is used as the basis for SNMP naming of mscX25DteLcn components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscX25DteLcnComponentName 1.3.6.1.4.1.562.36.2.1.90.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DteLcnStorageType 1.3.6.1.4.1.562.36.2.1.90.4.1.1.4
This variable represents the storage type value for the mscX25DteLcn tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DteLcnIndex 1.3.6.1.4.1.562.36.2.1.90.4.1.1.10
This variable represents the index for the mscX25DteLcn tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4095  

mscX25DteLcnStateTable 1.3.6.1.4.1.562.36.2.1.90.4.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnStateEntry

mscX25DteLcnStateEntry 1.3.6.1.4.1.562.36.2.1.90.4.10.1
An entry in the mscX25DteLcnStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnStateEntry  

mscX25DteLcnAdminState 1.3.6.1.4.1.562.36.2.1.90.4.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscX25DteLcnOperationalState 1.3.6.1.4.1.562.36.2.1.90.4.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscX25DteLcnUsageState 1.3.6.1.4.1.562.36.2.1.90.4.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscX25DteLcnCpTable 1.3.6.1.4.1.562.36.2.1.90.4.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the call parameters that are in use for this logical channel. For a PVC only the packet size and the window size attributes are meaningful.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnCpEntry

mscX25DteLcnCpEntry 1.3.6.1.4.1.562.36.2.1.90.4.11.1
An entry in the mscX25DteLcnCpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnCpEntry  

mscX25DteLcnInPacketSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.1
This attribute indicates the maximum receive packet size in octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DteLcnOutPacketSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.2
This attribute indicates the maximum transmit packet size in octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 16 | 32 | 64 | 128 | 256 | 512 | 1024 | 2048 | 4096  

mscX25DteLcnInWindowSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.3
This attribute indicates the receive window size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteLcnOutWindowSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.4
This attribute indicates the transmit window size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteLcnProposeReverseCharging 1.3.6.1.4.1.562.36.2.1.90.4.11.1.5
Specifies whether local/reverse charging was negotiated for this logical channel. To determine which end of the channel is paying for the call, this attribute must be examined in combination with the callDirection attribute. For example, if this attribute is set to reverse and the callDirection attribute indicates incoming, it means the incoming call signalled reverse charging, so the local end of the channel is being charged. On the other, if the value of this attribute is reverse and the callDirection is outgoing, it means that the call request sent to the link signalled reverse charging; so the remote end is charged. Similarly, a value of local must also be interpreted in combination with the callDirection to determine which end is being charged. If the value of the callDirection attribute is plcn, the proposeReverseCharging attribute is meaningless.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER reverse(2), local(3)  

mscX25DteLcnFastSelect 1.3.6.1.4.1.562.36.2.1.90.4.11.1.6
This attribute indicates whether the fast select was used in establishing this logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unrestricted(3), restricted(4), no(5)  

mscX25DteLcnOutThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.7
This attribute specifies the transmit throughput class.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17)  

mscX25DteLcnInThroughputClassSize 1.3.6.1.4.1.562.36.2.1.90.4.11.1.8
This attribute specifies the receive throughput class.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER n75(3), n150(4), n300(5), n600(6), n1200(7), n2400(8), n4800(9), n9600(10), n19200(11), n48000(12), n64000(13), notSpecified(17)  

mscX25DteLcnCugIndex 1.3.6.1.4.1.562.36.2.1.90.4.11.1.9
This attribute indicates the index of the Closed User Group facility used in establishing this logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DteLcnCugoaIndex 1.3.6.1.4.1.562.36.2.1.90.4.11.1.10
This attribute indicates the index of the Closed User Group with Outgoing Access facility used in establishing this logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..4)  

mscX25DteLcnNetworkUserIdentifier 1.3.6.1.4.1.562.36.2.1.90.4.11.1.11
Specifies the Network User Identifier used for this logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DteLcnChargingInformation 1.3.6.1.4.1.562.36.2.1.90.4.11.1.12
This attribute indicates whether or not the charging information facility was used in establishing this logical channel. A value of notSpecified means the facility was not signalled. A value of notRequested means the facility was signalled but charging information was not requested (that is, the charging info field of the facility was set Off). A value of requested means the facility was signalled to explicitly request charging information. DESCRIPTION
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSpecified(2), notRequested(3), requested(4)  

mscX25DteLcnRpoa 1.3.6.1.4.1.562.36.2.1.90.4.11.1.13
This attribute indicates the RPOA facility which was signalled in establishing this logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..108)  

mscX25DteLcnTrnstDlySlctnAInd 1.3.6.1.4.1.562.36.2.1.90.4.11.1.14
This attribute indicates the Transit Delay Selection and Indication value used for this logical channel. A value of 65536 means no facility was signalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65536  

mscX25DteLcnCallingNetworkFax 1.3.6.1.4.1.562.36.2.1.90.4.11.1.23
This attribute indicates the Calling Network facilities which were signalled in the call packet. A value of null (empty string) means no calling network facilities were signalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DteLcnCalledNetworkFax 1.3.6.1.4.1.562.36.2.1.90.4.11.1.24
This attribute indicates the called network facilities which were signalled in the call packet. A value of null (empty string) means no called network facilities were signalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..108)  

mscX25DteLcnCallUserData 1.3.6.1.4.1.562.36.2.1.90.4.11.1.25
This attribute indicates the user data which was signalled in the call packet. A value of null (empty string) means no user data was signalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..128)  

mscX25DteLcnLcnStatusTable 1.3.6.1.4.1.562.36.2.1.90.4.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the status for an X.25 Logical Channel.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnLcnStatusEntry

mscX25DteLcnLcnStatusEntry 1.3.6.1.4.1.562.36.2.1.90.4.12.1
An entry in the mscX25DteLcnLcnStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnLcnStatusEntry  

mscX25DteLcnStatus 1.3.6.1.4.1.562.36.2.1.90.4.12.1.1
This attribute indicates the current state of the logical channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER closed(2), calling(3), dataTransfer(4), clearing(5), resetting(7)  

mscX25DteLcnCallDirection 1.3.6.1.4.1.562.36.2.1.90.4.12.1.3
This attribute indicates the direction of the call that caused the establishment of this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER incoming(1), outgoing(2), permanentLcn(3)  

mscX25DteLcnCalledAddress 1.3.6.1.4.1.562.36.2.1.90.4.12.1.4
This attribute indicates the called X.25 address to which the call is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mscX25DteLcnCallingAddress 1.3.6.1.4.1.562.36.2.1.90.4.12.1.5
This attribute indicates the calling X.25 address from which the call originated
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mscX25DteLcnOriginalCalledAddress 1.3.6.1.4.1.562.36.2.1.90.4.12.1.6
This attribute indicates the X.25 address of the originally called DTE to which the call was attempted. This could be different from the value of the calledAddress attribute in the case where the original call was redirected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mscX25DteLcnStatsTable 1.3.6.1.4.1.562.36.2.1.90.4.13
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational statistics for an X.25 Logical Channel.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLcnStatsEntry

mscX25DteLcnStatsEntry 1.3.6.1.4.1.562.36.2.1.90.4.13.1
An entry in the mscX25DteLcnStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLcnStatsEntry  

mscX25DteLcnInUknownProtocols 1.3.6.1.4.1.562.36.2.1.90.4.13.1.1
This attribute counts the number packets received from link which were discareded because of an unkown or unsupported protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnInDataOctets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.2
This attribute counts the number of octets of user data received from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnInDataPackets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.3
This attribute counts the number of data packets received from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnInRmtInitiatedRsts 1.3.6.1.4.1.562.36.2.1.90.4.13.1.4
This attribute counts the number of reset packets, with a cause code of 'DTE initiated', which were received from the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnInPrvdrInitiatedRsts 1.3.6.1.4.1.562.36.2.1.90.4.13.1.5
This attribute counts the number of reset packets, with a cause code other than 'DTE initiated', which were received from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnInInterruptPackets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.6
This attribute counts the number of interrupt packets received from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnOutDataOctets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.7
This attribute counts the number of octets of user data sent to the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnOutDataPackets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.8
This attribute counts the number of data packets sent to link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnOutInterruptPackets 1.3.6.1.4.1.562.36.2.1.90.4.13.1.9
This attribute counts the number of interrupt packets sent to link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLcnT22ResetTimeouts 1.3.6.1.4.1.562.36.2.1.90.4.13.1.10
This attribute counts the number of times the t22 reset timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapb 1.3.6.1.4.1.562.36.2.1.90.5
OBJECT IDENTIFIER    

mscX25DteLapbRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.5.1
This entry controls the addition and deletion of mscX25DteLapb components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbRowStatusEntry

mscX25DteLapbRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.5.1.1
A single entry in the table represents a single mscX25DteLapb component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbRowStatusEntry  

mscX25DteLapbRowStatus 1.3.6.1.4.1.562.36.2.1.90.5.1.1.1
This variable is used as the basis for SNMP naming of mscX25DteLapb components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscX25DteLapbComponentName 1.3.6.1.4.1.562.36.2.1.90.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DteLapbStorageType 1.3.6.1.4.1.562.36.2.1.90.5.1.1.4
This variable represents the storage type value for the mscX25DteLapb tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DteLapbIndex 1.3.6.1.4.1.562.36.2.1.90.5.1.1.10
This variable represents the index for the mscX25DteLapb tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscX25DteLapbCpTable 1.3.6.1.4.1.562.36.2.1.90.5.10
X25Dte/n Lapb This group contains the set of configuration parameters for the LAPB interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbCpEntry

mscX25DteLapbCpEntry 1.3.6.1.4.1.562.36.2.1.90.5.10.1
An entry in the mscX25DteLapbCpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbCpEntry  

mscX25DteLapbStationType 1.3.6.1.4.1.562.36.2.1.90.5.10.1.1
This attribute specifies the DCE or the DTE role of operation for the LAPB interface. Changing this attribute will cause the lapb link to Reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dte(1), dce(2)  

mscX25DteLapbFrameSequencing 1.3.6.1.4.1.562.36.2.1.90.5.10.1.2
This attribute specifies the modulo of the frame sequence numbering of the LAPB interface. Changing this attribute will cause the lapb link to Reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER modulo8(1), modulo128(2)  

mscX25DteLapbN1FrameSize 1.3.6.1.4.1.562.36.2.1.90.5.10.1.3
This attribute specifies the maximum frame size in bits that can be transmitted or received. This value must be greater than or equal to the maximum packet size across the interface(in bits)+ max level 3 header size(in bits)+ max level 2 header size(in bits)+ crc in bits. (max Pkt size + -------------> 4096*8 max level 3 header size + ---> 4*8 level 2 header size + --------> 5*8 crc -------------------> 2*8)
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 40..32856  

mscX25DteLapbKWindowSize 1.3.6.1.4.1.562.36.2.1.90.5.10.1.4
This attribute specifies the window size. This is the maximum number of unacknowledged sequenced frames that may be outstanding from or to this interface at any one time. A window size of greater than 7 is only valid when the sequence numbering of frames is modulo 128.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..127  

mscX25DteLapbN2TransmitLimit 1.3.6.1.4.1.562.36.2.1.90.5.10.1.5
This attribute specifies the maximum number of times a frame can be transmitted before appropriate recovery action is taken.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..20  

mscX25DteLapbT1AckTimer 1.3.6.1.4.1.562.36.2.1.90.5.10.1.6
This attribute specifies the period in milliseconds within which an acknowledgment of a sent frame must be received. The value set for t1 ack timer must be less than the value set for the t4 idle probe timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..10000  

mscX25DteLapbT2AckDelayTimer 1.3.6.1.4.1.562.36.2.1.90.5.10.1.7
This attribute specifies the maximum period in milliseconds permissible to wait before sending an acknowledgment for a received in sequenced I-frame. A value of 0 means there will be no delay in acknowledgment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000  

mscX25DteLapbT4IdleProbeTimer 1.3.6.1.4.1.562.36.2.1.90.5.10.1.8
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, LAPB will poll its peer for status. The value set for t4 idle probe timer must be greater than the value set for the t1 ack timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1000..65535000  

mscX25DteLapbActionInitiate 1.3.6.1.4.1.562.36.2.1.90.5.10.1.9
This attribute specifies the action to be taken by the LAPB interface to initiate link setup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sendSABM(1), sendDM(3), none(4)  

mscX25DteLapbActionRecvDM 1.3.6.1.4.1.562.36.2.1.90.5.10.1.10
This attribute specifies the action to be taken by the LAPB interface when it receives a DM response.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sendSABM(1)  

mscX25DteLapbTxQDegradeThreshold 1.3.6.1.4.1.562.36.2.1.90.5.10.1.11
This attribute specifies the threshold of the number of higher layer packets queued, beyond which LAPB should initiate a service degrade alarm. A value of 65536 means no threshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..65536  

mscX25DteLapbTxQResetThreshold 1.3.6.1.4.1.562.36.2.1.90.5.10.1.12
This attribute specifies the threshold of the number of higher layer packets queued, beyond which LAPB should initiate an overload alarm and reset the link. A value of 65536 means no threshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..65536  

mscX25DteLapbStateTable 1.3.6.1.4.1.562.36.2.1.90.5.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbStateEntry

mscX25DteLapbStateEntry 1.3.6.1.4.1.562.36.2.1.90.5.11.1
An entry in the mscX25DteLapbStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbStateEntry  

mscX25DteLapbAdminState 1.3.6.1.4.1.562.36.2.1.90.5.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscX25DteLapbOperationalState 1.3.6.1.4.1.562.36.2.1.90.5.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscX25DteLapbUsageState 1.3.6.1.4.1.562.36.2.1.90.5.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscX25DteLapbStatusTable 1.3.6.1.4.1.562.36.2.1.90.5.12
This group contains the status for the LAPB interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbStatusEntry

mscX25DteLapbStatusEntry 1.3.6.1.4.1.562.36.2.1.90.5.12.1
An entry in the mscX25DteLapbStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbStatusEntry  

mscX25DteLapbCurrentState 1.3.6.1.4.1.562.36.2.1.90.5.12.1.1
This attribute specifies the current state of the LAPB interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), frameReject(3), disconnectRequest(4), informationTransfer(5), waitingAck(7)  

mscX25DteLapbLastStateChangeReason 1.3.6.1.4.1.562.36.2.1.90.5.12.1.2
This attribute specifies the reason for the most recent state change.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), abmEntered(2), abmeEntered(3), abmReset(4), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), frmrSent(11), n2TimeOut(12), other(13)  

mscX25DteLapbFrmrTransmit 1.3.6.1.4.1.562.36.2.1.90.5.12.1.3
This attribute specifies the Information field of the FRMR most recently sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..7)  

mscX25DteLapbFrmrReceive 1.3.6.1.4.1.562.36.2.1.90.5.12.1.4
This attribute specifies the Information field of the FRMR most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(0..7)  

mscX25DteLapbCurrentQueueSize 1.3.6.1.4.1.562.36.2.1.90.5.12.1.5
This attribute specifies the number of packets on the lapb transmit queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscX25DteLapbStatsTable 1.3.6.1.4.1.562.36.2.1.90.5.13
This group contains the statistics for the LAPB interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbStatsEntry

mscX25DteLapbStatsEntry 1.3.6.1.4.1.562.36.2.1.90.5.13.1
An entry in the mscX25DteLapbStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbStatsEntry  

mscX25DteLapbStateChanges 1.3.6.1.4.1.562.36.2.1.90.5.13.1.1
This attribute counts the number of times LAPB state has changed. Refer to the attribute 'linkState' for the set of possible states.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbRemoteBusy 1.3.6.1.4.1.562.36.2.1.90.5.13.1.2
This attribute counts the number of times transmission of an I-frame was un-successful due to a perceived remote busy condition (window closed or remote busy).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbTransmitRejectFrames 1.3.6.1.4.1.562.36.2.1.90.5.13.1.3
This attribute counts the number of REJ frames sent by the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbReceiveRejectFrames 1.3.6.1.4.1.562.36.2.1.90.5.13.1.4
This attribute counts the number of REJ frames received by the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbT1AckTimeout 1.3.6.1.4.1.562.36.2.1.90.5.13.1.5
This attribute counts the number of times the T1 timer has expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramer 1.3.6.1.4.1.562.36.2.1.90.5.2
OBJECT IDENTIFIER    

mscX25DteLapbFramerRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.5.2.1
This entry controls the addition and deletion of mscX25DteLapbFramer components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerRowStatusEntry

mscX25DteLapbFramerRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.1.1
A single entry in the table represents a single mscX25DteLapbFramer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerRowStatusEntry  

mscX25DteLapbFramerRowStatus 1.3.6.1.4.1.562.36.2.1.90.5.2.1.1.1
This variable is used as the basis for SNMP naming of mscX25DteLapbFramer components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscX25DteLapbFramerComponentName 1.3.6.1.4.1.562.36.2.1.90.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DteLapbFramerStorageType 1.3.6.1.4.1.562.36.2.1.90.5.2.1.1.4
This variable represents the storage type value for the mscX25DteLapbFramer tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DteLapbFramerIndex 1.3.6.1.4.1.562.36.2.1.90.5.2.1.1.10
This variable represents the index for the mscX25DteLapbFramer tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscX25DteLapbFramerProvTable 1.3.6.1.4.1.562.36.2.1.90.5.2.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerProvEntry

mscX25DteLapbFramerProvEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.10.1
An entry in the mscX25DteLapbFramerProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerProvEntry  

mscX25DteLapbFramerInterfaceName 1.3.6.1.4.1.562.36.2.1.90.5.2.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DteLapbFramerLinkTable 1.3.6.1.4.1.562.36.2.1.90.5.2.11
This group contains attributes defining the framing of data on the link interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerLinkEntry

mscX25DteLapbFramerLinkEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.11.1
An entry in the mscX25DteLapbFramerLinkTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerLinkEntry  

mscX25DteLapbFramerFlagsBetweenFrames 1.3.6.1.4.1.562.36.2.1.90.5.2.11.1.4
This attribute defines the number of flags that are inserted between frames sent to the link interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..16  

mscX25DteLapbFramerStateTable 1.3.6.1.4.1.562.36.2.1.90.5.2.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerStateEntry

mscX25DteLapbFramerStateEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.12.1
An entry in the mscX25DteLapbFramerStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerStateEntry  

mscX25DteLapbFramerAdminState 1.3.6.1.4.1.562.36.2.1.90.5.2.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscX25DteLapbFramerOperationalState 1.3.6.1.4.1.562.36.2.1.90.5.2.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscX25DteLapbFramerUsageState 1.3.6.1.4.1.562.36.2.1.90.5.2.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscX25DteLapbFramerStatsTable 1.3.6.1.4.1.562.36.2.1.90.5.2.13
This group contains the operational statistics data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerStatsEntry

mscX25DteLapbFramerStatsEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1
An entry in the mscX25DteLapbFramerStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerStatsEntry  

mscX25DteLapbFramerFrmToIf 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.1
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerFrmFromIf 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.2
The number of frames received from the link interface by Framer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerOctetFromIf 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.3
The number of bytes received from the link interface by Framer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerAborts 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.4
This attribute is the total number of aborts received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerCrcErrors 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.5
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerLrcErrors 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.6
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerNonOctetErrors 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.7
This attribute is the total number of frames that were non octet aligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerOverruns 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.8
This attribute is the total number of frames received from the link for which overruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerUnderruns 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.9
This attribute is the total number of frames transmitted to the link for which underruns occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mscX25DteLapbFramerFrmToIf64 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.14
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscX25DteLapbFramerFrmFromIf64 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.15
The number of frames received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscX25DteLapbFramerOctetFromIf64 1.3.6.1.4.1.562.36.2.1.90.5.2.13.1.16
The number of bytes received from the link interface by Framer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PassportCounter64  

mscX25DteLapbFramerUtilTable 1.3.6.1.4.1.562.36.2.1.90.5.2.14
This group contains the link utilizaiton operational data for a Framer component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteLapbFramerUtilEntry

mscX25DteLapbFramerUtilEntry 1.3.6.1.4.1.562.36.2.1.90.5.2.14.1
An entry in the mscX25DteLapbFramerUtilTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteLapbFramerUtilEntry  

mscX25DteLapbFramerNormPrioLinkUtilToIf 1.3.6.1.4.1.562.36.2.1.90.5.2.14.1.1
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

mscX25DteLapbFramerNormPrioLinkUtilFromIf 1.3.6.1.4.1.562.36.2.1.90.5.2.14.1.3
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32 0..100  

mscX25DtePle 1.3.6.1.4.1.562.36.2.1.90.6
OBJECT IDENTIFIER    

mscX25DtePleRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.6.1
This entry controls the addition and deletion of mscX25DtePle components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePleRowStatusEntry

mscX25DtePleRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.6.1.1
A single entry in the table represents a single mscX25DtePle component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePleRowStatusEntry  

mscX25DtePleRowStatus 1.3.6.1.4.1.562.36.2.1.90.6.1.1.1
This variable is used as the basis for SNMP naming of mscX25DtePle components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mscX25DtePleComponentName 1.3.6.1.4.1.562.36.2.1.90.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DtePleStorageType 1.3.6.1.4.1.562.36.2.1.90.6.1.1.4
This variable represents the storage type value for the mscX25DtePle tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DtePleIndex 1.3.6.1.4.1.562.36.2.1.90.6.1.1.10
This variable represents the index for the mscX25DtePle tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mscX25DtePleProvTable 1.3.6.1.4.1.562.36.2.1.90.6.10
This group contains the provisionable attributes relevant to an interface used to carry Multiprotocol Interconnect traffic over X.25.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePleProvEntry

mscX25DtePleProvEntry 1.3.6.1.4.1.562.36.2.1.90.6.10.1
An entry in the mscX25DtePleProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePleProvEntry  

mscX25DtePleInactivityTimer 1.3.6.1.4.1.562.36.2.1.90.6.10.1.1
This attribute specifies the period in milliseconds this interface will keep an idle connection open before closing it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65536000  

mscX25DtePleOpTable 1.3.6.1.4.1.562.36.2.1.90.6.11
This group contains the Operational attributes relevant to an interface used to carry Multiprotocol Interconnect traffic over X.25.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DtePleOpEntry

mscX25DtePleOpEntry 1.3.6.1.4.1.562.36.2.1.90.6.11.1
An entry in the mscX25DtePleOpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DtePleOpEntry  

mscX25DtePleEncAddrToX25LkupFlrs 1.3.6.1.4.1.562.36.2.1.90.6.11.1.1
This attribute indicates the number of times a translation attempt from an Encapsulation address to an X.25 address failed to find a corresponding X.25 address. Such a failure could occur when a Protocol Port, linked to a RemoteGroup via the linkToProtocolPort attribute of the RemoteGroup, requests through the software that a X.25 call be established to a particular Encapsulation address. If the RemoteGroup does not have a Peer component linked in its linkToPeer attribute list, with the encAddress attribute equal to the Encapsulation address specified, this counter will be incremented, because the corresponding Peer component needed to establish an X.25 connection was not found.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscX25DtePleLastFailedEncAddr 1.3.6.1.4.1.562.36.2.1.90.6.11.1.2
This attribute indicates the last Encapsulation address for which no corresponding X.25 address was found and thus caused encAddressToX25LkupFlrs to be incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(2..128)  

mscX25DtePleX25AddrToEncLkupFlrs 1.3.6.1.4.1.562.36.2.1.90.6.11.1.4
This attribute indicates the number of times a translation attempt from an X.25 address to an Encapsulation address failed to find a corresponding Encapsulation address. Such a failure could occur when a incoming call received from the link by the X.25 DTE is directed to a specific RemoteGroup because the called address matches the localAddress attribute of the RemoteGroup component. If the RemoteGroup component does not have a Peer component linked in its linkToPeer attribute list, with the x25Address attribute equal to the calling address from the incoming call packet, there is no appropriate Peer component, so the call is cleared and this counter is incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscX25DtePleLastFailedX25Addr 1.3.6.1.4.1.562.36.2.1.90.6.11.1.5
This field specifies the last X.25 address that caused x25AddressToEncLkupFlrs to be incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DigitString Size(0..15)  

mscX25DteRg 1.3.6.1.4.1.562.36.2.1.90.7
OBJECT IDENTIFIER    

mscX25DteRgRowStatusTable 1.3.6.1.4.1.562.36.2.1.90.7.1
This entry controls the addition and deletion of mscX25DteRg components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgRowStatusEntry

mscX25DteRgRowStatusEntry 1.3.6.1.4.1.562.36.2.1.90.7.1.1
A single entry in the table represents a single mscX25DteRg component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgRowStatusEntry  

mscX25DteRgRowStatus 1.3.6.1.4.1.562.36.2.1.90.7.1.1.1
This variable is used as the basis for SNMP naming of mscX25DteRg components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mscX25DteRgComponentName 1.3.6.1.4.1.562.36.2.1.90.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mscX25DteRgStorageType 1.3.6.1.4.1.562.36.2.1.90.7.1.1.4
This variable represents the storage type value for the mscX25DteRg tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mscX25DteRgIndex 1.3.6.1.4.1.562.36.2.1.90.7.1.1.10
This variable represents the index for the mscX25DteRg tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1023  

mscX25DteRgIfEntryTable 1.3.6.1.4.1.562.36.2.1.90.7.10
This group contains the provisionable attributes for the ifEntry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgIfEntryEntry

mscX25DteRgIfEntryEntry 1.3.6.1.4.1.562.36.2.1.90.7.10.1
An entry in the mscX25DteRgIfEntryTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgIfEntryEntry  

mscX25DteRgIfAdminStatus 1.3.6.1.4.1.562.36.2.1.90.7.10.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscX25DteRgIfIndex 1.3.6.1.4.1.562.36.2.1.90.7.10.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscX25DteRgProvTable 1.3.6.1.4.1.562.36.2.1.90.7.11
This group contains the provisionable attributes of the RemoteGroup component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgProvEntry

mscX25DteRgProvEntry 1.3.6.1.4.1.562.36.2.1.90.7.11.1
An entry in the mscX25DteRgProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgProvEntry  

mscX25DteRgLinkToProtocolPort 1.3.6.1.4.1.562.36.2.1.90.7.11.1.1
This attribute contains a protocol port component name. The attribute associates the application with a protocol port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DteRgLocalAddress 1.3.6.1.4.1.562.36.2.1.90.7.11.1.2
This attribute contains the unique X.25 address which identifies this RemoteGroup. It should correspond to the called address in X.25 incoming call packets which are to be directed to this RemoteGroup. This allows calls received from the link to be directed to the appropriate RemoteGroup based on the called address in the X.25 call packet. The RemoteGroup components allow the X.25 interface to be shared amongst a number of Protocol Ports (and ultimately Virtual Routers) because each RemoteGroup is coupled with a specific ProtocolPort through its linkToProtocolPort attribute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DigitString Size(1..15)  

mscX25DteRgMtuSize 1.3.6.1.4.1.562.36.2.1.90.7.11.1.3
This attribute specifies the Maximum Transmit Unit (MTU); that is, the size of the largest datagram (in octets) which can be sent/ received on the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 576..9188  

mscX25DteRgStateTable 1.3.6.1.4.1.562.36.2.1.90.7.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgStateEntry

mscX25DteRgStateEntry 1.3.6.1.4.1.562.36.2.1.90.7.12.1
An entry in the mscX25DteRgStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgStateEntry  

mscX25DteRgAdminState 1.3.6.1.4.1.562.36.2.1.90.7.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscX25DteRgOperationalState 1.3.6.1.4.1.562.36.2.1.90.7.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscX25DteRgUsageState 1.3.6.1.4.1.562.36.2.1.90.7.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscX25DteRgOperStatusTable 1.3.6.1.4.1.562.36.2.1.90.7.13
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgOperStatusEntry

mscX25DteRgOperStatusEntry 1.3.6.1.4.1.562.36.2.1.90.7.13.1
An entry in the mscX25DteRgOperStatusTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgOperStatusEntry  

mscX25DteRgSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.90.7.13.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscX25DteRgLTPlcnTable 1.3.6.1.4.1.562.36.2.1.90.7.210
This attribute is a list of links to PermLcn components. The set of all Peer and PermLcn components which link to a given RemoteGroup determine the subset of remote hosts which are accessible to a particular Protocol Port (and ultimately a Virtual Router).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgLTPlcnEntry

mscX25DteRgLTPlcnEntry 1.3.6.1.4.1.562.36.2.1.90.7.210.1
An entry in the mscX25DteRgLTPlcnTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgLTPlcnEntry  

mscX25DteRgLTPlcnValue 1.3.6.1.4.1.562.36.2.1.90.7.210.1.1
This variable represents both the value and the index for the mscX25DteRgLTPlcnTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DteRgLTPlcnRowStatus 1.3.6.1.4.1.562.36.2.1.90.7.210.1.2
This variable is used to control the addition and deletion of individual values of the mscX25DteRgLTPlcnTable.
Status: mandatory Access: write-only
OBJECT-TYPE    
  RowStatus  

mscX25DteRgLtPeerTable 1.3.6.1.4.1.562.36.2.1.90.7.211
This attribute gives a list of links to Peer components. The set of all Peer and PermLcn components which link to a given RemoteGroup determine the subset of remote hosts which are accessible to a particular Protocol Port (and ultimately a Virtual Router).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgLtPeerEntry

mscX25DteRgLtPeerEntry 1.3.6.1.4.1.562.36.2.1.90.7.211.1
An entry in the mscX25DteRgLtPeerTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgLtPeerEntry  

mscX25DteRgLtPeerValue 1.3.6.1.4.1.562.36.2.1.90.7.211.1.1
This variable represents both the value and the index for the mscX25DteRgLtPeerTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Link  

mscX25DteRgLtPeerRowStatus 1.3.6.1.4.1.562.36.2.1.90.7.211.1.2
This variable is used to control the addition and deletion of individual values of the mscX25DteRgLtPeerTable.
Status: mandatory Access: write-only
OBJECT-TYPE    
  RowStatus  

mscX25DteRgLcnTable 1.3.6.1.4.1.562.36.2.1.90.7.212
This attribute lists the Lcn components for the X25Dte, which belong to this RemoteGroup. There is an Lcn component listed here for every lcn connection belonging to this RemoteGroup. The lcns were established using either a Peer component linked to this RemoteGroup (in response to a switched call) or using a PermLcn component linked to this RemoteGroup (a permanent connection).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscX25DteRgLcnEntry

mscX25DteRgLcnEntry 1.3.6.1.4.1.562.36.2.1.90.7.212.1
An entry in the mscX25DteRgLcnTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MscX25DteRgLcnEntry  

mscX25DteRgLcnValue 1.3.6.1.4.1.562.36.2.1.90.7.212.1.1
This variable represents both the value and the index for the mscX25DteRgLcnTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32 1..4095  

x25DteGroup 1.3.6.1.4.1.562.36.2.2.48.1
OBJECT IDENTIFIER    

x25DteGroupCA 1.3.6.1.4.1.562.36.2.2.48.1.1
OBJECT IDENTIFIER    

x25DteGroupCA02 1.3.6.1.4.1.562.36.2.2.48.1.1.3
OBJECT IDENTIFIER    

x25DteGroupCA02A 1.3.6.1.4.1.562.36.2.2.48.1.1.3.2
OBJECT IDENTIFIER    

x25DteCapabilities 1.3.6.1.4.1.562.36.2.2.48.3
OBJECT IDENTIFIER    

x25DteCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.48.3.1
OBJECT IDENTIFIER    

x25DteCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.48.3.1.3
OBJECT IDENTIFIER    

x25DteCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.48.3.1.3.2
OBJECT IDENTIFIER    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor