A3Com-Llc-r1-MIB

File: A3Com-Llc-r1-MIB.mib (94612 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC1213-MIB
RFC-1212

Imported symbols

enterprises Counter Gauge
TimeTicks IpAddress Integer32
DisplayString ifIndex OBJECT-TYPE

Defined Objects

a3com 1.3.6.1.4.1.43
OBJECT IDENTIFIER    

brouterMIB 1.3.6.1.4.1.43.2
OBJECT IDENTIFIER    

llc 1.3.6.1.4.1.43.2.26
OBJECT IDENTIFIER    

llcPortGroup 1.3.6.1.4.1.43.2.26.1
OBJECT IDENTIFIER    

llcPortAdminTable 1.3.6.1.4.1.43.2.26.1.1
This table contains objects that can be changed to manage an LLC port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. The operating values may be different from these configured values if a configured parameter was changed after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcPortAdminEntry

llcPortAdminEntry 1.3.6.1.4.1.43.2.26.1.1.1
A list of configured values for an LLC port.
OBJECT-TYPE    
  LlcPortAdminEntry  

llcPortAdminName 1.3.6.1.4.1.43.2.26.1.1.1.1
An octet string that defines the physical port to which this interface is assigned. It has implementation-specific significance. Its value shall be unique within the administered system. It must contain only ASCII printable characters.
OBJECT-TYPE    
  DisplayString SIZE(1..10)  

llcPortAdminMaxSaps 1.3.6.1.4.1.43.2.26.1.1.1.2
This parameter specifies the maximum number of SAPs that can be defined for this port.
OBJECT-TYPE    
  Gauge  

llcPortAdminMaxCcs 1.3.6.1.4.1.43.2.26.1.1.1.3
This parameter specifies the maximum number of connection components that can be administratively defined for this port.
OBJECT-TYPE    
  Gauge  

llcPortAdminMaxPDUOctets 1.3.6.1.4.1.43.2.26.1.1.1.4
This object denotes the default maximum I PDU size, in octets, that LLCs on this port may send to and receive from their remote LLC partners. This count is referred to as 'N1' in the IEEE 802.2 specification [5]. This size includes I-Frames, UI-Frames, XIDs, and TEST frames. The I PDU size includes all octets in a frame, excluding framing characters, the MAC header, and the LLC header.
OBJECT-TYPE    
  Integer32  

llcPortAdminMaxUnackedIPDUsSend 1.3.6.1.4.1.43.2.26.1.1.1.5
This object denotes the default maximum consecutive unacknowledged I PDU frames that LLCs on this port may send to their remote LLC partners. This count is referred to as 'k' in the IEEE 802.2 specification [5]. At connection setup, the remote LLC may send, using an XID frame, the maximum number of unacknowledged I PDUs which it is prepared to receive. If so, an implementation may choose to override the administered maximum number of unacknowledged PDUs with the dynamically learned value and should reflect this in the llcCcOperMaxUnackedIPDUsSend object for the connection component.
OBJECT-TYPE    
  INTEGER 1..127  

llcPortAdminMaxUnackedIPDUsRcv 1.3.6.1.4.1.43.2.26.1.1.1.6
This object denotes the default maximum number of unacknowledged I PDUs that LLCs on this port can expect to receive from their remote LLC partners. This count is referred to as 'k' in the IEEE 802.2 specification [5]. At connection setup, an implementation may choose to send this value to the remote LLC, using an XID frame.
OBJECT-TYPE    
  INTEGER 1..127  

llcPortAdminMaxRetransmits 1.3.6.1.4.1.43.2.26.1.1.1.7
This object denotes the default value for the maximum number of times which LLCs on this port shall retry a PDU following the expiration of the acknowledgement timer, the P-bit timer or the reject timer. When these retries are exhausted, the link shall be declared inactive. This count is referred to as 'N2' in the IEEE 802.2 specification [5].
OBJECT-TYPE    
  Integer32  

llcPortAdminAckTimer 1.3.6.1.4.1.43.2.26.1.1.1.8
This object denotes the default value for the time interval during which the LLCs on this port shall expect to receive either: 1) an acknowledgement to one or more outstanding I PDUs. or 2) a response PDU to an unnumbered command PDU. The expiration of this timer shall cause the unacknowledged frames to be retransmitted (up to N2 times). For Implementations that only use a single 'T1' Value (ref. IBM Token-Ring Network technical reference Chapter 11). This object will be used to control/read the value.
OBJECT-TYPE    
  TimeTicks  

llcPortAdminPbitTimer 1.3.6.1.4.1.43.2.26.1.1.1.9
This object denotes the default value for the time interval during which the LLCs on this port shall expect to receive a PDU with the F bit set to '1' in response to a Type 2 command with the P bit set to '1'. The expiration of this timer shall cause the command with the poll bit to be retransmitted (up to N2 times).
OBJECT-TYPE    
  TimeTicks  

llcPortAdminRejTimer 1.3.6.1.4.1.43.2.26.1.1.1.10
This object denotes the default value for the time interval during which the LLCs on this port shall expect to receive a reply to a REJ PDU. The expiration of this timer shall cause the REJ PDU to be retransmitted (up to N2 times).
OBJECT-TYPE    
  TimeTicks  

llcPortAdminBusyTimer 1.3.6.1.4.1.43.2.26.1.1.1.11
This object denotes the default value for the time interval during which the LLCs on this port shall expect to receive an indication that a busy condition at the remote LLC has cleared. The expiration of this timer causes the adjacent connection component to be polled.
OBJECT-TYPE    
  TimeTicks  

llcPortAdminInactTimer 1.3.6.1.4.1.43.2.26.1.1.1.12
This object denotes the default value for the time interval during which the LLCs on this port shall expect to receive any PDU from the remote LLC. This function is not described in the IEEE 802.2 specification [5]. It is listed in the IBM Token-Ring Network Architecture [6] Reference as the Ti parameter and is widely implemented. The expiration of this timer shall cause the local LLC to send a PDU to the remote LLC with the P bit set to '1'. Any value for this object less than or equal to the acknowledgement timer shall mean that the timer is not used.
OBJECT-TYPE    
  TimeTicks  

llcPortAdminDelayAckCount 1.3.6.1.4.1.43.2.26.1.1.1.13
This object denotes the default value for the maximum number of consecutive I PDUs which the LLCs on this port shall receive during the interval defined by llcCcOperDelayTimer without sending an immediate acknowledgement. This must be less than or equal to the value of llcCcOperMaxUnackIPDUsRcv. This function is not described in the IEEE 802.2 specification [5]. It is listed in the IBM Token-Ring Network Architecture Reference [6] as the N3 parameter and is widely implemented. A value of one indicates that acknowledgments will be sent immediately and that the value of llcPortAdminDelayAckTimer shall be ignored.
OBJECT-TYPE    
  Integer32  

llcPortAdminDelayAckTimer 1.3.6.1.4.1.43.2.26.1.1.1.14
This object denotes the default value for the time interval during which the LLCs on this port shall delay acknowledgment of one or more I PDUs (up to the value of llcCcOperDelayAckCount). This function is not described in the IEEE 802.2 specification [5]. It is listed in the IBM Token-Ring Network Architecture Reference [6] as the T2 parameter and is widely implemented. The expiration of this timer shall cause the local LLC to acknowledge all unacknowledged I PDUs. A value of 0 means that an acknowledgement will be sent immediately. This object is associated with the llcPortAdminDelayAckCount object and is only defined if that object has a value greater than one.
OBJECT-TYPE    
  TimeTicks  

llcPortAdminNw 1.3.6.1.4.1.43.2.26.1.1.1.15
This object denotes the default value for the number of IPDUs that must be acknowledged before the working window size (Ww) can be incremented by 1 when the working window is not equal to the maximum transmit window size (TW). It controls the gradual incrementing of Ww in congestion situations. This function is not described in the IEEE 802.2 specification [5]. However, it is listed in the IBM Token-Ring Network Architecture Reference [6] as the Nw parameter and is widely implemented.
OBJECT-TYPE    
  Integer32  

llcPortOperTable 1.3.6.1.4.1.43.2.26.1.2
This table contains current LLC port parameters. Many of these objects have corresponding objects in the llcPortAdminTable.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcPortOperEntry

llcPortOperEntry 1.3.6.1.4.1.43.2.26.1.2.1
Currently set parameters for a specific LLC port.
OBJECT-TYPE    
  LlcPortOperEntry  

llcPortOperNumSaps 1.3.6.1.4.1.43.2.26.1.2.1.1
This object defines the number of SAPs on this port that are currently enabled. In other words, this object is a count of the number of instances of llcSapOperEntry that have a llcSapOperStatus value of 'active(2)'.
OBJECT-TYPE    
  Gauge  

llcPortOperSimRim 1.3.6.1.4.1.43.2.26.1.2.1.2
This object reflects support for transmission and receipt of SIM and RIM control frames for this port. SIM and RIM are not defined in the ANSI/IEEE 802.2 specification [5] nor in the IBM Token Ring Architecture Reference [6]. These control frames are used for the remote program load of IBM communications processors.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

llcPortOperLastModifyTime 1.3.6.1.4.1.43.2.26.1.2.1.3
This object describes the value of sysUpTime when this port definition was last modified. If the port has not been modified, then this value shall be zero.
OBJECT-TYPE    
  TimeTicks  

llcSapGroup 1.3.6.1.4.1.43.2.26.2
OBJECT IDENTIFIER    

llcSapAdminTable 1.3.6.1.4.1.43.2.26.2.1
This table contains objects that can be changed to manage a local SAP. Changing one of these parameters may take effect in the operating SAP immediately or may wait until the interface is restarted depending on the details of the implementation. The operating values may be different from these configured values if a configured parameter was changed after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcSapAdminEntry

llcSapAdminEntry 1.3.6.1.4.1.43.2.26.2.1.1
A list of configured values for a local SAP.
OBJECT-TYPE    
  LlcSapAdminEntry  

llcSapNumber 1.3.6.1.4.1.43.2.26.2.1.1.1
The address of this local SAP.
OBJECT-TYPE    
  INTEGER 1..254  

llcSapOperTable 1.3.6.1.4.1.43.2.26.2.2
This table contains objects that reflect the current operational parameters of a local SAP.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcSapOperEntry

llcSapOperEntry 1.3.6.1.4.1.43.2.26.2.2.1
A list of configured values for a local SAP.
OBJECT-TYPE    
  LlcSapOperEntry  

llcSapOperStatus 1.3.6.1.4.1.43.2.26.2.2.1.1
This parameter describes the actual state of this local SAP.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

llcSapOperNumCcs 1.3.6.1.4.1.43.2.26.2.2.1.2
This object defines the number of connection components on this SAP that are currently in one of the 'connected' states. In other words, this object is a count of the number of instances of llcCcOperEntry that have a llcCcOperState value greater than or equal to 'normal(3)'.
OBJECT-TYPE    
  Integer32  

llcSapOperLlc2Support 1.3.6.1.4.1.43.2.26.2.2.1.3
This parameter describes whether or not the LLC implementation supports LLC2 connection components.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

llcSapStatsTable 1.3.6.1.4.1.43.2.26.2.3
This table contains objects that reflect the current operational statistics of a local SAP.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcSapStatsEntry

llcSapStatsEntry 1.3.6.1.4.1.43.2.26.2.3.1
A list of configured values for a local SAP.
OBJECT-TYPE    
  LlcSapStatsEntry  

llcSapStatsLocalBusies 1.3.6.1.4.1.43.2.26.2.3.1.1
This object reflects the total number of times that the local connection components on this SAP have entered a busy state (RNR). This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsRemoteBusies 1.3.6.1.4.1.43.2.26.2.3.1.2
This object reflects the total number of times that the adjacent (i.e. remote) connection components on this SAP have entered a busy state (RNR). This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsIFramesIn 1.3.6.1.4.1.43.2.26.2.3.1.3
This object reflects the total number of I-Frames that have been received by connection components on this SAP. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsIFramesOut 1.3.6.1.4.1.43.2.26.2.3.1.4
This object reflects the total number of I-Frames that have been transmitted by connection components on this SAP. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsIOctetsIn 1.3.6.1.4.1.43.2.26.2.3.1.5
This object reflects the total octets received from adjacent connection components on this SAP. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsIOctetsOut 1.3.6.1.4.1.43.2.26.2.3.1.6
This object reflects the total octets transmitted to adjacent connection components on this SAP. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsSFramesIn 1.3.6.1.4.1.43.2.26.2.3.1.7
This object reflects the total number of S-Frames that have been received by connection components on this SAP. This object is initialized to zero when the SAP is created. Note - the ratio of the number of I-Frames to S-Frames might serve as a measure of link efficiency and, for instance, could be used to tune the acknowledgement timer.
OBJECT-TYPE    
  Counter  

llcSapStatsSFramesOut 1.3.6.1.4.1.43.2.26.2.3.1.8
This object reflects the total number of S-Frames that have been transmitted by connection components on this SAP. This object is initialized to zero when the SAP is created. Note - the ratio of the number of I-Frames to S-Frames might serve as a measure of link efficiency and, for instance, could be used to tune the acknowledgement timer.
OBJECT-TYPE    
  Counter  

llcSapStatsRetransmitsOut 1.3.6.1.4.1.43.2.26.2.3.1.9
This object reflects the total number of I-Frames retransmitted by all local connection components on this SAP. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsREJsIn 1.3.6.1.4.1.43.2.26.2.3.1.10
This object reflects the total REJ frames received from all adjacent LLC connection components on this SAP since it was created.
OBJECT-TYPE    
  Counter  

llcSapStatsREJsOut 1.3.6.1.4.1.43.2.26.2.3.1.11
This object reflects the total REJ frames transmitted to an adjacent LLC connection components on this SAP since it was created.
OBJECT-TYPE    
  Counter  

llcSapStatsWwCount 1.3.6.1.4.1.43.2.26.2.3.1.12
This object reflects the total number of times, since this SAP was created, that the dynamic window algorithm has been invoked to reduce the value of Ww on any of the connection components of this SAP. This object is initialized to zero when the SAP is created. This function is not described in the IEEE 802.2 specification [5], but is widely implemented.
OBJECT-TYPE    
  Counter  

llcSapStatsTESTCommandsIn 1.3.6.1.4.1.43.2.26.2.3.1.13
This object denotes the number of TEST commands this SAP has received and is a measure of the number of stations in the network trying to connect up. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsTESTCommandsOut 1.3.6.1.4.1.43.2.26.2.3.1.14
This object denotes the number of TEST commands this SAP has sent and is a measure of the number of other stations we are trying to connect to. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsTESTResponsesIn 1.3.6.1.4.1.43.2.26.2.3.1.15
This object denotes the number of TEST responses this SAP has received and is a measure of the number of stations in the network responding to TEST commands this SAP has sent. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsTESTResponsesOut 1.3.6.1.4.1.43.2.26.2.3.1.16
This object denotes the number of TEST responses this SAP has sent and is a measure of the number of other stations trying to connect to this SAP. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsXIDCommandsIn 1.3.6.1.4.1.43.2.26.2.3.1.17
This object denotes the number of XID commands this SAP has received and is a measure of the number of stations in the network trying to connect to this SAP. This object is a count of all XIDs, including SNA XID, IEEE XID, null XID, and non-activation XIDs. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsXIDCommandsOut 1.3.6.1.4.1.43.2.26.2.3.1.18
This object denotes the number of XID commands this SAP has sent and is a measure of the number of other stations this SAP is trying to connect to. This object is a count of all XIDs, including SNA XID, IEEE XID, null XID, and non-activation XIDs. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsXIDResponsesIn 1.3.6.1.4.1.43.2.26.2.3.1.19
This object denotes the number of XID responses this SAP has received and is a measure of the number of stations in the network responding to TEST commands this SAP has sent. This object is a count of all XIDs, including SNA XID, IEEE XID, null XID, and non-activation XIDs. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsXIDResponsesOut 1.3.6.1.4.1.43.2.26.2.3.1.20
This object denotes the number of XID responses this SAP has sent and is a measure of the number of other stations trying to connect to this SAP. This object is a count of all XIDs, including SNA XID, IEEE XID, null XID, and non-activation XIDs. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsUIFramesIn 1.3.6.1.4.1.43.2.26.2.3.1.21
This object reflects the total number of unnumbered information (UI) frames received on a local SAP.
OBJECT-TYPE    
  Counter  

llcSapStatsUIFramesOut 1.3.6.1.4.1.43.2.26.2.3.1.22
This object reflects the total number of unnumbered information (UI) frames sent on a local SAP.
OBJECT-TYPE    
  Counter  

llcSapStatsUIOctetsIn 1.3.6.1.4.1.43.2.26.2.3.1.23
This object reflects the total octets received from adjacent connection components on this SAP. This object covers the address, control, and information field of UI-Frames only. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsUIOctetsOut 1.3.6.1.4.1.43.2.26.2.3.1.24
This object reflects the total octets transmitted to adjacent connection components on this SAP. This object covers the address, control, and information field of UI-Frames only. This object is initialized to zero when the SAP is created.
OBJECT-TYPE    
  Counter  

llcSapStatsConnectOk 1.3.6.1.4.1.43.2.26.2.3.1.25
This object reflects the total number of successful connections that have been established on this SAP since the SAP was created. A successful connection is indicated by a successful SABME/UA exchange.
OBJECT-TYPE    
  Counter  

llcSapStatsConnectFail 1.3.6.1.4.1.43.2.26.2.3.1.26
This object reflects the total number of unsuccessful connections that have been attempted on this SAP since the SAP was created. An unsuccessful connection attempt is indicated by a SABME/DM exchange or a SABME/timeout.
OBJECT-TYPE    
  Counter  

llcSapStatsDisconnect 1.3.6.1.4.1.43.2.26.2.3.1.27
This object reflects the total number of normal disconnections that have been performed on this SAP since the SAP was created. A normal disconnection is indicated by a successful DISC/UA exchange or merely a DISC sent or received.
OBJECT-TYPE    
  Counter  

llcSapStatsDisconnectFRMRSend 1.3.6.1.4.1.43.2.26.2.3.1.28
This object reflects the total number of abnormal disconnections (resulting from a FRMR being sent) that have been performed on this SAP since the SAP was created.
OBJECT-TYPE    
  Counter  

llcSapStatsDisconnectFRMRRcv 1.3.6.1.4.1.43.2.26.2.3.1.29
This object reflects the total number of abnormal disconnections (resulting from a FRMR being received) that have been performed on this SAP since the SAP was created.
OBJECT-TYPE    
  Counter  

llcSapStatsDisconnectTimer 1.3.6.1.4.1.43.2.26.2.3.1.30
This object reflects the total number of abnormal disconnections (resulting from a timer expiration) that have been performed on this SAP since the SAP was created.
OBJECT-TYPE    
  Counter  

llcSapStatsReset 1.3.6.1.4.1.43.2.26.2.3.1.31
This object reflects the total number of resets that have been performed on this SAP since the SAP was created. A reset is ...
OBJECT-TYPE    
  Counter  

llcCcGroup 1.3.6.1.4.1.43.2.26.3
OBJECT IDENTIFIER    

llcCcAdminTable 1.3.6.1.4.1.43.2.26.3.1
This table contains objects that can be changed to manage an LLC connection component. Changing one of these parameters may take effect in the operating link immediately or may wait until the link is restarted depending on the details of the implementation. The operating values may be different from these configured values if changed by XID negotiation or if a configured parameter was changed after the link was started.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcCcAdminEntry

llcCcAdminEntry 1.3.6.1.4.1.43.2.26.3.1.1
A list of configured values for an LLC connection component.
OBJECT-TYPE    
  LlcCcAdminEntry  

llcCcLSap 1.3.6.1.4.1.43.2.26.3.1.1.1
This value is the address of the local SAP for this Connection Component.
OBJECT-TYPE    
  INTEGER 1..254  

llcCcRSap 1.3.6.1.4.1.43.2.26.3.1.1.2
This value is the address of the remote SAP for this Connection Component.
OBJECT-TYPE    
  INTEGER 1..254  

llcCcLMac 1.3.6.1.4.1.43.2.26.3.1.1.3
This value is the local MAC address for this Connection Component.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

llcCcRMac 1.3.6.1.4.1.43.2.26.3.1.1.4
This value is the remote MAC address for this Connection Component.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

llcCcOperTable 1.3.6.1.4.1.43.2.26.3.2
This table contains current LLC link parameters. Many of these objects have corresponding objects in the llcCcAdminTable.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcCcOperEntry

llcCcOperEntry 1.3.6.1.4.1.43.2.26.3.2.1
A list of status and control values for an LLC connection component.
OBJECT-TYPE    
  LlcCcOperEntry  

llcCcOperState 1.3.6.1.4.1.43.2.26.3.2.1.1
This object describes the operational state of the LLC connection. If the connection component is disabled, llcCcOperState will be allowed to transition to aDM(1). If the connection component is enabled, llcCcOperState will be allowed to transition to normal(3).
OBJECT-TYPE    
  INTEGER aDM(1), setup(2), normal(3), busy(4), reject(5), await(6), awaitBusy(7), awaitReject(8), dConn(9), reset(10), error(11), conn(12), resetCheck(13), resetWait(14)  

llcCcOperMaxIPDUOctetsSend 1.3.6.1.4.1.43.2.26.3.2.1.2
This object denotes the maximum I PDU size, in octets, that this LLC SAP may send to its remote connection component partner. This count is referred to as 'N1' in the IEEE 802.2 specification [5]. At connection setup, the remote LLC may send, using an XID frame, the maximum I PDU size which it is prepared to receive. If so, an implementation may choose to override the administered maximum PDU size with the dynamically learned value and should reflect that in this object. The I PDU size includes all octets in a frame, excluding framing characters, the MAC header and link header.
OBJECT-TYPE    
  Integer32  

llcCcOperMaxIPDUOctetsRcv 1.3.6.1.4.1.43.2.26.3.2.1.3
This object denotes the maximum I PDU size,in octets, that this LLC can expect to receive from its remote LLC partner. This count is referred to as 'N1' in the IEEE 802.2 specification [5] The I PDU size includes all octets in a frame with the exception of the framing characters, the MAC header and the link header.
OBJECT-TYPE    
  Integer32  

llcCcOperMaxUnackedIPDUsSend 1.3.6.1.4.1.43.2.26.3.2.1.4
This object denotes the maximum consecutive unacknowledged I PDU frames that this LLC may send to its remote LLC partner. This count is referred to as 'k' in the IEEE 802.2 specification [5]. At connection setup, the remote LLC may send, using an XID frame, the maximum number of unacknowledged I PDUs which it is prepared to receive. If so, an implementation may choose to override the administered maximum number of unacknowledged PDUs with the dynamically learned value and should reflect that in this object.
OBJECT-TYPE    
  INTEGER 1..127  

llcCcOperMaxUnackedIPDUsRcv 1.3.6.1.4.1.43.2.26.3.2.1.5
This object denotes the maximum number of unacknowledged I PDUs that this LLC can expect to receive from its remote LLC partner. This count is referred to as 'k' in the IEEE 802.2 specification [5].
OBJECT-TYPE    
  INTEGER 1..127  

llcCcOperMaxRetransmits 1.3.6.1.4.1.43.2.26.3.2.1.6
This object denotes the value for the maximum number of times that this LLC shall retry PDUs following the expiration of the acknowledgement timer, the P-bit timer or the reject timer. When these retries are exhausted, the link shall be declared inactive. This count is referred to as 'N2' in the IEEE 802.2 specification [5].
OBJECT-TYPE    
  Integer32  

llcCcOperAckTimer 1.3.6.1.4.1.43.2.26.3.2.1.7
This object denotes the value for the time interval during which this LLC shall expect to receive either: 1) an acknowledgement to one or more outstanding I PDUs. or 2) a response PDU to an unnumbered command PDU. The expiration of this timer shall cause the frame unacknowledged frames to be retransmitted (up to N2 times).
OBJECT-TYPE    
  TimeTicks  

llcCcOperPbitTimer 1.3.6.1.4.1.43.2.26.3.2.1.8
This object denotes the value for the time interval during which this LLC shall expect to receive a PDU with the F bit set to '1' in response to a Type 2 command with the P bit set to '1'. The expiration of this timer shall cause the REJ PDU to be retransmitted (up to N2 times).
OBJECT-TYPE    
  TimeTicks  

llcCcOperRejTimer 1.3.6.1.4.1.43.2.26.3.2.1.9
This object denotes the value for the time interval during which this LLC shall expect to receive a reply to a REJ PDU. The expiration of this timer shall cause the REJ PDU to be retransmitted (up to N2 times).
OBJECT-TYPE    
  TimeTicks  

llcCcOperBusyTimer 1.3.6.1.4.1.43.2.26.3.2.1.10
This object denotes the value for the time interval during which this LLC shall expect to receive an indication that a busy condition at the remote LLC has cleared.
OBJECT-TYPE    
  TimeTicks  

llcCcOperInactTimer 1.3.6.1.4.1.43.2.26.3.2.1.11
This object denotes the value for the time interval during which this LLC shall expect to receive any PDU from the remote LLC. This function is not described in the IEEE 802.2 specification [5] but is widely implemented. The expiration of this timer shall cause the local LLC to send a PDU to the remote LLC with the P bit set to '1'. Any value for this object less than or equal to the acknowledgement timer shall mean that the timer is not used.
OBJECT-TYPE    
  TimeTicks  

llcCcOperDelayAckCount 1.3.6.1.4.1.43.2.26.3.2.1.12
This object denotes the value for the maximum number of consecutive I PDUs which this LLC shall receive during the interval defined by llcCcOperDelayTimer without sending an immediate acknowledgement. This must be less than or equal to the value of llcCcOperMaxUnackIPDUsRcv. This function is not described in the IEEE 802.2 specification [5] but is widely implemented. A value of one indicates that acknowledgments will be sent immediately and that the value of llcCcOperDelayAckTimer should be ignored.
OBJECT-TYPE    
  Integer32  

llcCcOperDelayAckTimer 1.3.6.1.4.1.43.2.26.3.2.1.13
This object denotes the value for the time interval during which this LLC shall delay acknowledgment of one or more I PDUs (up to the value of llcCcOperDelayAckCount). This function is not described in the IEEE 802.2 specification [5] but is widely implemented. The expiration of this timer shall cause the local LLC to acknowledge all unacknowledged I PDUs. This object is associated with the llcCcOperDelayAckCount object and only has meaning if that object has a value greater than one.
OBJECT-TYPE    
  TimeTicks  

llcCcOperNw 1.3.6.1.4.1.43.2.26.3.2.1.14
This object denotes the value for the number of IPDUs that must be acknowledged before the working window size (Ww) can be incremented by 1 when the working window is not equal to the maximum transmit window size (TW). It controls the gradual incrementing of Ww in congestion situations. This function is not described in the IEEE 802.2 specification [5], but is widely implemented.
OBJECT-TYPE    
  Integer32  

llcCcOperWw 1.3.6.1.4.1.43.2.26.3.2.1.15
Maximum number of sequentially numbered IPDUs that the connection component may have outstanding (unacknowledged) at any given time. Ww is initialized to the value of llcCcOperMaxUnackedIPDUsSend when the link is established. When the dynamic window algorithm is invoked, Ww varies from 1 up to llcCcOperMaxUnackedIPDUsSend. Each time the llcCcOperWw value is decreased, the reason is recorded in llcCcOperLastWwCause, and llcCcStatWwCount is incremented by 1. This function is not described in the IEEE 802.2 specification [5], but is widely implemented.
OBJECT-TYPE    
  INTEGER 1..127  

llcCcOperCreateTime 1.3.6.1.4.1.43.2.26.3.2.1.16
This object describes the value of sysUpTime when this row was created.
OBJECT-TYPE    
  TimeTicks  

llcCcOperLastModifyTime 1.3.6.1.4.1.43.2.26.3.2.1.17
For administered connection components, this object describes the value of sysUpTime the last time this row was modified. If the row has not been modified, then this value shall be zero. For dynamic connection components, this object identifies the time this connection component was created.
OBJECT-TYPE    
  TimeTicks  

llcCcOperLastFailTime 1.3.6.1.4.1.43.2.26.3.2.1.18
This object describes the value of sysUpTime the last time this connection component failed. Connection component failure is defined as a transition to an llcCcOperState value of aDM(1). If the connection component has not failed, then this value shall be zero.
OBJECT-TYPE    
  TimeTicks  

llcCcOperLastFailCause 1.3.6.1.4.1.43.2.26.3.2.1.19
This enumerated object reflects the cause of the last failure of this LLC connection component. If the connection component has not failed, then this object will have a value of undefined(1).
OBJECT-TYPE    
  INTEGER undefined(1), rxFRMR(2), txFRMR(3), discReceived(4), discSent(5), retriesExpired(6), forcedShutdown(7)  

llcCcOperLastFailFRMRInfo 1.3.6.1.4.1.43.2.26.3.2.1.20
This object reflects the information field of the FRMR frame if the last failure for this LLC connection component was a result of an invalid frame. Otherwise, this field has no meaning.
OBJECT-TYPE    
  OCTET STRING SIZE(5)  

llcCcOperLastWwCause 1.3.6.1.4.1.43.2.26.3.2.1.21
This object indicates the reason that the llcCcOperWw was reduced the last time this occurred.
OBJECT-TYPE    
  INTEGER neverInvoked(1), lostData(2), macLayerCongestion(3), other(4)  

llcCcStatsTable 1.3.6.1.4.1.43.2.26.3.3
Each entry in this table contains statistics for a specific LLC connection component.
OBJECT-TYPE    
  SEQUENCE OF  
    LlcCcStatsEntry

llcCcStatsEntry 1.3.6.1.4.1.43.2.26.3.3.1
A list of statistics for an LLC connection component.
OBJECT-TYPE    
  LlcCcStatsEntry  

llcCcStatsLocalBusies 1.3.6.1.4.1.43.2.26.3.3.1.1
This object reflects the total number of times that the local connection component has entered a busy state (RNR). This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsRemoteBusies 1.3.6.1.4.1.43.2.26.3.3.1.2
This object reflects the total number of times that the adjacent (i.e. remote) connection component has entered a busy state (RNR). This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsIFramesIn 1.3.6.1.4.1.43.2.26.3.3.1.3
This object reflects the total number of I-Frames that have been received by the connection component. This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsIFramesOut 1.3.6.1.4.1.43.2.26.3.3.1.4
This object reflects the total number of I-Frames that have been transmitted by this connection component. This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsIOctetsIn 1.3.6.1.4.1.43.2.26.3.3.1.5
This object reflects the total octets received from the adjacent connection component. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsIOctetsOut 1.3.6.1.4.1.43.2.26.3.3.1.6
This object reflects the total octets transmitted to the adjacent connection component. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsSFramesIn 1.3.6.1.4.1.43.2.26.3.3.1.7
This object reflects the total number of S-Frames that have been received by this connection component. This object is initialized to zero when the connection component is created. Note - the ratio of the number of I-Frames to S-Frames might serve as a measure of link efficiency and, for instance, could be used to tune the acknowledgement timer.
OBJECT-TYPE    
  Counter  

llcCcStatsSFramesOut 1.3.6.1.4.1.43.2.26.3.3.1.8
This object reflects the total number of S-Frames that have been transmitted by this connection component. This object is initialized to zero when the connection component is created. Note - the ratio of the number of I-Frames to S-Frames might serve as a measure of link efficiency and, for instance, could be used to tune the acknowledgement timer.
OBJECT-TYPE    
  Counter  

llcCcStatsRetransmitsOut 1.3.6.1.4.1.43.2.26.3.3.1.9
This object reflects the total number of I-Frames retransmitted by the local connection component. This object is initialized to zero when the connection component is created.
OBJECT-TYPE    
  Counter  

llcCcStatsREJsIn 1.3.6.1.4.1.43.2.26.3.3.1.10
This object reflects the total REJ frames received from an adjacent LLC connection component since connection component startup.
OBJECT-TYPE    
  Counter  

llcCcStatsREJsOut 1.3.6.1.4.1.43.2.26.3.3.1.11
This object reflects the total REJ frames transmitted to an adjacent LLC connection component since connection component startup.
OBJECT-TYPE    
  Counter  

llcCcStatsWwCount 1.3.6.1.4.1.43.2.26.3.3.1.12
This object reflects the total number of times, since connection component startup, that the dynamic window algorithm has been invoked to reduce the value of Ww. At connection component startup, this object must be initialized to zero. This function is not described in the IEEE 802.2 specification [5], but is widely implemented.
OBJECT-TYPE    
  Counter  

llcTunnelGroup 1.3.6.1.4.1.43.2.26.4
OBJECT IDENTIFIER    

ccsLlcTunnelInfo 1.3.6.1.4.1.43.2.26.4.1
OBJECT IDENTIFIER    

ccsLlcTunnelVirtualRing 1.3.6.1.4.1.43.2.26.4.1.1
This defines the number of the virtual token ring used by Logical Link Control. Changing this parameter may take effect for the tunnel immediately or may wait until the tunnel is restarted depending on the details of the implementation.
OBJECT-TYPE    
  INTEGER 1..4095  

ccsLlcTunnelMode 1.3.6.1.4.1.43.2.26.4.1.2
This allows one to enable tunneling on the box and describe the mode of operation i.e. Secure or NonSecure. Secure mode means that this box will only accept connection from partners listed in the tunnel peer list. In the non- Secure mode any incoming IP address is accepted. This parameter may combine one of qTunnelEnable and qTunnelDisable (Enable/Disable set) with one of qTunnelSecure and qTunnelNonSecure (Secure/Nonsecure set); e.g. qTunnelEnable and qTunnelSecure is a legal combination. If a member of one set is not supplied on a 'write' operation, the value for that set remains unchanged. Changing this parameter may take effect for the tunnel immediately or may wait until the tunnel is restarted depending on the details of the implementation.
OBJECT-TYPE    
  INTEGER qTunnelEnable(4), qTunnelDisable(8), qTunnelSecure(16), qTunnelEnableSecure(20), qTunnelDisableSecure(24), qTunnelNonSecure(32), qTunnelEnableNonSecure(36), qTunnelDisableNonSecure(40)  

ccsLlcTunnelSNAPriority 1.3.6.1.4.1.43.2.26.4.1.3
This determines the priority of the tunnel traffic on the Logical Link Control link. Changing this parameter may take effect for the tunnel immediately or may wait until the tunnel is restarted depending on the details of the implementation.
OBJECT-TYPE    
  INTEGER qPrioDefault(1), qPrioHigh(2), qPrioMedium(3), qPrioLow(4)  

ccsLlcTunnelRouterTable 1.3.6.1.4.1.43.2.26.4.2
A table of information regarding all routers participating in Logical Link Control 2. Changing one of these parameters may take effect for the tunnel immediately or may wait until the tunnel is restarted depending on the details of the implementation.
OBJECT-TYPE    
  SEQUENCE OF  
    CcsLlcTunnelRouterEntry

ccsLlcTunnelRouterEntry 1.3.6.1.4.1.43.2.26.4.2.1
Information for a single participating router.
OBJECT-TYPE    
  CcsLlcTunnelRouterEntry  

ccsLlcPeerAddress 1.3.6.1.4.1.43.2.26.4.2.1.1
The IP address of the Logical Link Control node's peer. The peer is at the remote end of the tunnel.
OBJECT-TYPE    
  IpAddress  

ccsLlcLocalAddress 1.3.6.1.4.1.43.2.26.4.2.1.2
The IP address of the Logical Link Control node at the local end of the tunnel.
OBJECT-TYPE    
  IpAddress  

ccsLlcTunnelId 1.3.6.1.4.1.43.2.26.4.2.1.3
The tunnel index. This is a unique identifier for the tunnel.
OBJECT-TYPE    
  INTEGER 0..63  

ccsLlcRouterEnable 1.3.6.1.4.1.43.2.26.4.2.1.4
Allows tunnel peer to be enabled.
OBJECT-TYPE    
  INTEGER qTunEnable(1), qtunDisable(2)  

ccsLlcRouterMode 1.3.6.1.4.1.43.2.26.4.2.1.5
Mode of the peer.
OBJECT-TYPE    
  INTEGER qTransparent(1), qSpecificTerm(2), qLocalTerm(3)  

ccsLlcRouterTunnelTransport 1.3.6.1.4.1.43.2.26.4.2.1.6
Type of transport protocol used for tunnelling.
OBJECT-TYPE    
  INTEGER qTcp(2)  

ccsLlcRouterTunnelPort 1.3.6.1.4.1.43.2.26.4.2.1.7
Port number if TCP is used for tunnelling.
OBJECT-TYPE    
  INTEGER 0..32767  

ccsLlcRouterPeerString 1.3.6.1.4.1.43.2.26.4.2.1.8
The name of Logical Link Control node's peer.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ccsLlcTunnelDefaultDestTable 1.3.6.1.4.1.43.2.26.4.3
Table of default routes for frames that arrive at this router. The route on which a particular frame is sent is determined from the frames's destination MAC address. Changing one of these parameters may take effect for the tunnel immediately or may wait until the tunnel is restarted depending on the details of the implementation.
OBJECT-TYPE    
  SEQUENCE OF  
    CcsLlcTunnelDefaultDestEntry

ccsLlcTunnelDefaultDestEntry 1.3.6.1.4.1.43.2.26.4.3.1
Mapping of a MAC address to a destination router.
OBJECT-TYPE    
  CcsLlcTunnelDefaultDestEntry  

ccsLlcDestTunnelId 1.3.6.1.4.1.43.2.26.4.3.1.1
The destination's llcTunnelId for it's associated ccsLlcTunnelRouterTable entry.
OBJECT-TYPE    
  INTEGER 0..63  

ccsLlcRemoteMacAddress 1.3.6.1.4.1.43.2.26.4.3.1.2
The MAC address used for reaching the remote router.
OBJECT-TYPE    
  MacAddress  

ccsLlcRemoteSap 1.3.6.1.4.1.43.2.26.4.3.1.3
The current Service Access Port used for reaching the destination address.
OBJECT-TYPE    
  INTEGER 0..255  

ccsLlcRemoteSapLowRange 1.3.6.1.4.1.43.2.26.4.3.1.4
The lowest Service Access Port that can be used to reach the destination address.
OBJECT-TYPE    
  INTEGER 0..255  

ccsLlcRemoteSapHighRange 1.3.6.1.4.1.43.2.26.4.3.1.5
The highest Service Access Port that can be used to reach the destination address.
OBJECT-TYPE    
  INTEGER 0..255  

Defined Objects

MacAddress  
OCTET STRING SIZE(6)    

LlcPortAdminEntry  
SEQUENCE    
  DisplayString as llcPortAdminName  
  Gauge as llcPortAdminMaxSaps  
  Gauge as llcPortAdminMaxCcs  
  Integer32 as llcPortAdminMaxPDUOctets  
  INTEGER as llcPortAdminMaxUnackedIPDUsSend  
  INTEGER as llcPortAdminMaxUnackedIPDUsRcv  
  Integer32 as llcPortAdminMaxRetransmits  
  TimeTicks as llcPortAdminAckTimer  
  TimeTicks as llcPortAdminPbitTimer  
  TimeTicks as llcPortAdminRejTimer  
  TimeTicks as llcPortAdminBusyTimer  
  TimeTicks as llcPortAdminInactTimer  
  Integer32 as llcPortAdminDelayAckCount  
  TimeTicks as llcPortAdminDelayAckTimer  
  Integer32 as llcPortAdminNw  

LlcPortOperEntry  
SEQUENCE    
  Gauge as llcPortOperNumSaps  
  INTEGER as llcPortOperSimRim  
  TimeTicks as llcPortOperLastModifyTime  

LlcSapAdminEntry  
SEQUENCE    
  INTEGER as llcSapNumber  

LlcSapOperEntry  
SEQUENCE    
  INTEGER as llcSapOperStatus  
  Integer32 as llcSapOperNumCcs  
  INTEGER as llcSapOperLlc2Support  

LlcSapStatsEntry  
SEQUENCE    
  Counter as llcSapStatsLocalBusies  
  Counter as llcSapStatsRemoteBusies  
  Counter as llcSapStatsIFramesIn  
  Counter as llcSapStatsIFramesOut  
  Counter as llcSapStatsIOctetsIn  
  Counter as llcSapStatsIOctetsOut  
  Counter as llcSapStatsSFramesIn  
  Counter as llcSapStatsSFramesOut  
  Counter as llcSapStatsRetransmitsOut  
  Counter as llcSapStatsREJsIn  
  Counter as llcSapStatsREJsOut  
  Counter as llcSapStatsWwCount  
  Counter as llcSapStatsTESTCommandsIn  
  Counter as llcSapStatsTESTCommandsOut  
  Counter as llcSapStatsTESTResponsesIn  
  Counter as llcSapStatsTESTResponsesOut  
  Counter as llcSapStatsXIDCommandsIn  
  Counter as llcSapStatsXIDCommandsOut  
  Counter as llcSapStatsXIDResponsesIn  
  Counter as llcSapStatsXIDResponsesOut  
  Counter as llcSapStatsUIFramesIn  
  Counter as llcSapStatsUIFramesOut  
  Counter as llcSapStatsUIOctetsIn  
  Counter as llcSapStatsUIOctetsOut  
  Counter as llcSapStatsConnectOk  
  Counter as llcSapStatsConnectFail  
  Counter as llcSapStatsDisconnect  
  Counter as llcSapStatsDisconnectFRMRSend  
  Counter as llcSapStatsDisconnectFRMRRcv  
  Counter as llcSapStatsDisconnectTimer  
  Counter as llcSapStatsReset  

LlcCcAdminEntry  
SEQUENCE    
  INTEGER as llcCcLSap  
  INTEGER as llcCcRSap  
  OCTET STRING as llcCcLMac  
  OCTET STRING as llcCcRMac  

LlcCcOperEntry  
SEQUENCE    
  INTEGER as llcCcOperState  
  Integer32 as llcCcOperMaxIPDUOctetsSend  
  Integer32 as llcCcOperMaxIPDUOctetsRcv  
  INTEGER as llcCcOperMaxUnackedIPDUsSend  
  INTEGER as llcCcOperMaxUnackedIPDUsRcv  
  Integer32 as llcCcOperMaxRetransmits  
  TimeTicks as llcCcOperAckTimer  
  TimeTicks as llcCcOperPbitTimer  
  TimeTicks as llcCcOperRejTimer  
  TimeTicks as llcCcOperBusyTimer  
  TimeTicks as llcCcOperInactTimer  
  Integer32 as llcCcOperDelayAckCount  
  TimeTicks as llcCcOperDelayAckTimer  
  Integer32 as llcCcOperNw  
  INTEGER as llcCcOperWw  
  TimeTicks as llcCcOperCreateTime  
  TimeTicks as llcCcOperLastModifyTime  
  TimeTicks as llcCcOperLastFailTime  
  INTEGER as llcCcOperLastFailCause  
  OCTET STRING as llcCcOperLastFailFRMRInfo  
  INTEGER as llcCcOperLastWwCause  

LlcCcStatsEntry  
SEQUENCE    
  Counter as llcCcStatsLocalBusies  
  Counter as llcCcStatsRemoteBusies  
  Counter as llcCcStatsIFramesIn  
  Counter as llcCcStatsIFramesOut  
  Counter as llcCcStatsIOctetsIn  
  Counter as llcCcStatsIOctetsOut  
  Counter as llcCcStatsSFramesIn  
  Counter as llcCcStatsSFramesOut  
  Counter as llcCcStatsRetransmitsOut  
  Counter as llcCcStatsREJsIn  
  Counter as llcCcStatsREJsOut  
  Counter as llcCcStatsWwCount  

CcsLlcTunnelRouterEntry  
SEQUENCE    
  IpAddress as ccsLlcPeerAddress  
  IpAddress as ccsLlcLocalAddress  
  INTEGER as ccsLlcTunnelId  
  INTEGER as ccsLlcRouterEnable  
  INTEGER as ccsLlcRouterMode  
  INTEGER as ccsLlcRouterTunnelTransport  
  INTEGER as ccsLlcRouterTunnelPort  
  DisplayString as ccsLlcRouterPeerString  

CcsLlcTunnelDefaultDestEntry  
SEQUENCE    
  INTEGER as ccsLlcDestTunnelId  
  MacAddress as ccsLlcRemoteMacAddress  
  INTEGER as ccsLlcRemoteSap  
  INTEGER as ccsLlcRemoteSapLowRange  
  INTEGER as ccsLlcRemoteSapHighRange