
| RFC1155-SMI | ACC-SYSTEM | ACC-MIB |
| OBJECT-TYPE | accTrapLogSeqNum | accBRG |
| DisplayString | RowStatus | IfIndex |
| SmdsAddress |
| accDs1ExtTable | 1.3.6.1.4.1.5.1.1.42 | ||
| The DS1 extension table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AccDs1ExtEntry | |||
| accDs1ExtEntry | 1.3.6.1.4.1.5.1.1.42.1 | ||
| An entry in the DS1 extension table. | |||
| OBJECT-TYPE | |||
| AccDs1ExtEntry | |||
| accDs1ExtLineIndex | 1.3.6.1.4.1.5.1.1.42.1.1 | ||
| This object is the identifier of a DS1 Interface on a managed device. It has the same value as dsx1LineIndex. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1ExtLineLength | 1.3.6.1.4.1.5.1.1.42.1.2 | ||
| The approximate line length. When equipped with a DSX1 line interface module, this object selects the transmit equalization. When equipped with a CSU interface module, this object selects the line build out (LBO). | |||
| OBJECT-TYPE | |||
| INTEGER | short(1), medium(2), long(3) | ||
| accDS1ExtNfasGroup | 1.3.6.1.4.1.5.1.1.42.1.3 | ||
| The ifIndex of another DS1 interface whose common signaling channel (e.g., ISDN D channel) carries signaling information for this DS1 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1ExtInterfaceId | 1.3.6.1.4.1.5.1.1.42.1.4 | ||
| The internal interface on which signalling is received. 0 indicates the D-channel. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..31 | ||
| accDs1ExtE1Type | 1.3.6.1.4.1.5.1.1.42.1.5 | ||
| The type of E1 equipment to which the device is connected. Only used to work around Nordic type switch anomolies. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), nordic(2) | ||
| accDs1ExtXcvr | 1.3.6.1.4.1.5.1.1.42.1.6 | ||
| The type of transceiver installed. | |||
| OBJECT-TYPE | |||
| INTEGER | dsx1(1), csu2(2), hdsl-master(3), hdsl-slave(4), e1-120ohm(5), hdsl(6), e1-75ohm(7) | ||
| accDs1ExtPrecedence | 1.3.6.1.4.1.5.1.1.42.1.7 | ||
| When the interface is provisioned as a PRI interface with D-channel backup, this object determines whether the D channel on this interface is the primary or secondary D channel. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| accDs1ExtSignalGroup | 1.3.6.1.4.1.5.1.1.42.1.8 | ||
| The index of the Signal group assigned to this interface. The value of the trunk group index is limited to the maximum number of PRI interfaces that can be installed on a given platform (3 for Amazon, 28 for Tigris). A trunk group value of 0 indicates that the interface does not belong to a PRI trunk group. Replaces accDs1ExtNfasGroup which has been deprecated. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..127 | ||
| accDs1ExtNumberGroup | 1.3.6.1.4.1.5.1.1.42.1.9 | ||
| The index of the called number group assigned to this interface. Number groups are defined in the Called Number Table. A number group value of 0 indicates that no called number group has been assigned to this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1ExtIntegAccess | 1.3.6.1.4.1.5.1.1.42.1.10 | ||
| Indicates whether this interface has enabled integrated access. If enabled, the signal group is used as the signaling channel for this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| accDs1ExtSignalMode | 1.3.6.1.4.1.5.1.1.42.1.11 | ||
| Signaling mode for this DS1 interface | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), rbs(2), cas(3), ccs(4), nfas(5), etheric(6) | ||
| accDs1ExtCICBase | 1.3.6.1.4.1.5.1.1.42.1.12 | ||
| CIC base to use for circuits on this DS1 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1ExtMessageLevel | 1.3.6.1.4.1.5.1.1.42.1.13 | ||
| Maintenance message level for this DS1 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1ExtServiceState | 1.3.6.1.4.1.5.1.1.42.1.14 | ||
| Describes DS1 service state. Certain attributes need to be in a specific state to be changed. | |||
| OBJECT-TYPE | |||
| INTEGER | ds1InService(1), ds1OutOfService(2) | ||
| accDs1CircuitTable | 1.3.6.1.4.1.5.1.1.43 | ||
| The DS1 circuit configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AccDs1CircuitEntry | |||
| accDs1CircuitEntry | 1.3.6.1.4.1.5.1.1.43.1 | ||
| An entry in the DS1 circuit configuration table. | |||
| OBJECT-TYPE | |||
| AccDs1CircuitEntry | |||
| accDs1CircuitIndex | 1.3.6.1.4.1.5.1.1.43.1.1 | ||
| This object is the identifier of a circuit on a managed DS1 interface. It should have the same value as ifIndex. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| accDs1CircuitAdi | 1.3.6.1.4.1.5.1.1.43.1.2 | ||
| Enables or disables alternate digit inversion for a circuit on a managed DS1 interface. This object applies only to E1 interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| accDs1CircuitBandwidth | 1.3.6.1.4.1.5.1.1.43.1.3 | ||
| The bandwidth of the circuit in kilobits per second. | |||
| OBJECT-TYPE | |||
| INTEGER | bandwidth-8(1), bandwidth-16(2), bandwidth-24(3), bandwidth-32(4), bandwidth-40(5), bandwidth-48(6), bandwidth-56(7), bandwidth-64(8) | ||
| accDs1CircuitBusyout | 1.3.6.1.4.1.5.1.1.43.1.4 | ||
| The busyout status of a circuit. If the status is set to busy, the circuit is taken out of service and is unable to carry user data. | |||
| OBJECT-TYPE | |||
| INTEGER | busy(1), unbusy(2) | ||
| accDs1CircuitInversion | 1.3.6.1.4.1.5.1.1.43.1.5 | ||
| Enables or disables circuit inversion for a circuit on a managed DS1 interface. This object applies only to T1 interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| accDs1CircuitName | 1.3.6.1.4.1.5.1.1.43.1.6 | ||
| This object is used to associate a name with a particular DS1 circuit. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| accDs1CircuitConfigStatus | 1.3.6.1.4.1.5.1.1.43.1.7 | ||
| This object gives the configuration status for a circuit entry, and may have the following values: UNCONFIG The circuit has not been configured or has been deleted STATIC The circuit has been configured manually (stored in NVM) DYNAMIC The circuit has been configured automatically (not stored in NVM) | |||
| OBJECT-TYPE | |||
| INTEGER | unconfig(1), static(2), dynamic(3) | ||
| accDs1CircuitLoopback | 1.3.6.1.4.1.5.1.1.43.1.8 | ||
| This object represents the loopback status of the DS1 circuit. Any active loopback can be removed by setting the loopback status to none. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), loopback-a(2), loopback-c(3) | ||
| accDs1CircuitRbs | 1.3.6.1.4.1.5.1.1.43.1.9 | ||
| Enables or disables robbed bit signaling for a circuit on a managed DS1 interface. This object applies only to T1 interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| accDs1CircuitSuperrateMask | 1.3.6.1.4.1.5.1.1.43.1.10 | ||
| Specifies the time-slots used by a superrate circuit. Each bit which is set corresponds to a time-slot which is allocated to the superrate circuit. 2**n-1 corresponds to time-slot n. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| AccDs1ExtEntry | |||
| SEQUENCE | |||
| INTEGER as accDs1ExtLineIndex | |||
| INTEGER as accDs1ExtLineLength | |||
| INTEGER as accDS1ExtNfasGroup | |||
| INTEGER as accDs1ExtInterfaceId | |||
| INTEGER as accDs1ExtE1Type | |||
| INTEGER as accDs1ExtXcvr | |||
| INTEGER as accDs1ExtPrecedence | |||
| INTEGER as accDs1ExtSignalGroup | |||
| INTEGER as accDs1ExtNumberGroup | |||
| INTEGER as accDs1ExtIntegAccess | |||
| INTEGER as accDs1ExtSignalMode | |||
| INTEGER as accDs1ExtCICBase | |||
| INTEGER as accDs1ExtMessageLevel | |||
| INTEGER as accDs1ExtServiceState | |||
| AccDs1CircuitEntry | |||
| SEQUENCE | |||
| INTEGER as accDs1CircuitIndex | |||
| INTEGER as accDs1CircuitAdi | |||
| INTEGER as accDs1CircuitBandwidth | |||
| INTEGER as accDs1CircuitBusyout | |||
| INTEGER as accDs1CircuitInversion | |||
| DisplayString as accDs1CircuitName | |||
| INTEGER as accDs1CircuitConfigStatus | |||
| INTEGER as accDs1CircuitLoopback | |||
| INTEGER as accDs1CircuitRbs | |||
| INTEGER as accDs1CircuitSuperrateMask | |||