ACC-ISDN

File: ACC-ISDN.mib (67886 bytes)

Imported modules

RFC1155-SMI RFC-1215 ACC-SYSTEM
ACC-MIB

Imported symbols

OBJECT-TYPE IpAddress TimeTicks
Gauge Counter TRAP-TYPE
accTrapLogSeqNum accBRG DisplayString
RowStatus IfIndex SmdsAddress
accTrapLogSeverityType

Defined Objects

accIsdn 1.3.6.1.4.1.5.1.1.36
OBJECT IDENTIFIER    

accIsdnDsl 1.3.6.1.4.1.5.1.1.36.1
OBJECT IDENTIFIER    

accIsdnDslIndex 1.3.6.1.4.1.5.1.1.36.1.1
An index instantiating a particular digital subscriber loop interface on this bridge/router terminal.
OBJECT-TYPE    
  INTEGER 1..255  

accIsdnSubTable 1.3.6.1.4.1.5.1.1.36.2
ISDN subscriber table containing configuration and operational parameters for all ISDN subscriber interfaces on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnSubEntry

accIsdnSubEntry 1.3.6.1.4.1.5.1.1.36.2.1
Configuration and operational parameters for a particular ISDN subscriber interface.
OBJECT-TYPE    
  AccIsdnSubEntry  

accIsdnSubSwitchType 1.3.6.1.4.1.5.1.1.36.2.1.1
The particular type of central-office switch providing access to the ISDN network and to which this subscriber interface is connected.
OBJECT-TYPE    
  INTEGER bri-net3(1), bri-5ess(2), bri-dms100(3), bri-vn2(4), bri-vn3(5), bri-kdd(6), bri-ntt(7), bri-1tr6(8), bri-ni1(9), bri-ccitt(10)  

accIsdnSubChannelMode 1.3.6.1.4.1.5.1.1.36.2.1.2
The ISDN channel configuration mode.
OBJECT-TYPE    
  INTEGER cm-1b-plus-d(1), cm-2b-plus-d(2), cm-1h-plus-d(3)  

accIsdnSubAdminStatus 1.3.6.1.4.1.5.1.1.36.2.1.3
The administrative status of this subscriber interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accIsdnSubDiagLevel 1.3.6.1.4.1.5.1.1.36.2.1.4
The current diagnostic message level for this subscriber interface.
OBJECT-TYPE    
  INTEGER 0..5  

accIsdnSubManualTei 1.3.6.1.4.1.5.1.1.36.2.1.5
The TEI (terminal endpoint identifier) when manual TEI assignment is required. Setting this value between 0 and 63 (inclusive) specifies manual TEI assignment using the indicated value. Setting this value to 127 (the broadcast TEI) specifies automatic TEI assignment.
OBJECT-TYPE    
  INTEGER 0..63  

accIsdnStatTable 1.3.6.1.4.1.5.1.1.36.3
Statistics and operational status maintained for all ISDN subscriber interfaces on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnStatEntry

accIsdnStatEntry 1.3.6.1.4.1.5.1.1.36.3.1
Statistics and operational status for a particular ISDN subscriber interface.
OBJECT-TYPE    
  AccIsdnStatEntry  

accIsdnStatHdlcInPackets 1.3.6.1.4.1.5.1.1.36.3.1.1
The number of packets received on the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcInOctets 1.3.6.1.4.1.5.1.1.36.3.1.2
The number of octets received on the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcInErrors 1.3.6.1.4.1.5.1.1.36.3.1.3
The number of input hardware errors counted by the D-channel input/output driver.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcInDiscs 1.3.6.1.4.1.5.1.1.36.3.1.4
The number of input packets discarded by the D-channel input/output driver.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcOutPackets 1.3.6.1.4.1.5.1.1.36.3.1.5
The number of packets transmitted on the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcOutOctets 1.3.6.1.4.1.5.1.1.36.3.1.6
The number of octets transmitted on the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcOutErrors 1.3.6.1.4.1.5.1.1.36.3.1.7
The number of output hardware errors counted by the D-channel input/output driver.
OBJECT-TYPE    
  Counter  

accIsdnStatHdlcOutDiscs 1.3.6.1.4.1.5.1.1.36.3.1.8
The number of output packets discarded by the D-channel input/output driver.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdUnsolicResps 1.3.6.1.4.1.5.1.1.36.3.1.9
The number of unsolicited LAPD response frames received on all data links associated with the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdPeerSabmes 1.3.6.1.4.1.5.1.1.36.3.1.10
The number of peer SABME frames received on all data links associated with the D-channel of this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdN200Errors 1.3.6.1.4.1.5.1.1.36.3.1.11
The number of unsuccessful T200 timer recoveries after a frame has been retransmitted N200 times.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdNrSeqErrors 1.3.6.1.4.1.5.1.1.36.3.1.12
The number of N(R) sequence errors.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdRecvdFrmrs 1.3.6.1.4.1.5.1.1.36.3.1.13
The number of LAPD FRMR response frames received.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdCntlErrors 1.3.6.1.4.1.5.1.1.36.3.1.14
The number of LAPD frames received with an invalid or non-implemented control field.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdInfoErrors 1.3.6.1.4.1.5.1.1.36.3.1.15
The number of LAPD frames received with a non-permitted information (I) field.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdWrongSizes 1.3.6.1.4.1.5.1.1.36.3.1.16
The number of LAPD frames received which were the wrong size.
OBJECT-TYPE    
  Counter  

accIsdnStatLapdN201Errors 1.3.6.1.4.1.5.1.1.36.3.1.17
The number of LAPD frames received which contained and information field which exceeded N201.
OBJECT-TYPE    
  Counter  

accIsdnStatCallsOriginateds 1.3.6.1.4.1.5.1.1.36.3.1.18
The number of outgoing calls originated on this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatCallsOfferreds 1.3.6.1.4.1.5.1.1.36.3.1.19
The number of incoming calls offerred on this subscriber interface.
OBJECT-TYPE    
  Counter  

accIsdnStatCallsAnswereds 1.3.6.1.4.1.5.1.1.36.3.1.20
The number of outgoing calls originated on this subscriber interface which were answered by the destination.
OBJECT-TYPE    
  Counter  

accIsdnStatCallsAccepteds 1.3.6.1.4.1.5.1.1.36.3.1.21
The number of incoming calls offerred on this subscriber interface which were accepted for connection.
OBJECT-TYPE    
  Counter  

accIsdnStatCallsCompleteds 1.3.6.1.4.1.5.1.1.36.3.1.22
The number of outgoing and incoming calls completed (that is, the number of calls which were successfully connected).
OBJECT-TYPE    
  Counter  

accIsdnStatCallsCleareds 1.3.6.1.4.1.5.1.1.36.3.1.23
The number of outgoing and incoming calls cleared.
OBJECT-TYPE    
  Counter  

accIsdnStatDslOperStatus 1.3.6.1.4.1.5.1.1.36.3.1.24
The operation status of this interface.
OBJECT-TYPE    
  INTEGER inactive(1), waiting(2), activated(3), established(4)  

accIsdnStatLastCauses 1.3.6.1.4.1.5.1.1.36.3.1.25
The last cause value sent or received on this subscriber interface.
OBJECT-TYPE    
  INTEGER 0..255  

accIsdnCallTable 1.3.6.1.4.1.5.1.1.36.4
Parameters and operational status for ISDN calls active on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnCallEntry

accIsdnCallEntry 1.3.6.1.4.1.5.1.1.36.4.1
Parameters and operational status for a particular ISDN call which is presently active or is in the process of being established or cleared.
OBJECT-TYPE    
  AccIsdnCallEntry  

accIsdnCallIdentifier 1.3.6.1.4.1.5.1.1.36.4.1.1
The internal call control identifier for this call.
OBJECT-TYPE    
  INTEGER 0..65536  

accIsdnCallReference 1.3.6.1.4.1.5.1.1.36.4.1.2
The Q.931 call reference value for this call.
OBJECT-TYPE    
  INTEGER 1..32767  

accIsdnCallChannelId 1.3.6.1.4.1.5.1.1.36.4.1.3
The bearer channel interface ID allocated for this call.
OBJECT-TYPE    
  INTEGER none(1), b1(2), b2(3), h0(4)  

accIsdnCallIfIndex 1.3.6.1.4.1.5.1.1.36.4.1.4
The interface index of the physical port connected by the bearer channel.
OBJECT-TYPE    
  INTEGER j1(1), j2(2)  

accIsdnCallInfoRate 1.3.6.1.4.1.5.1.1.36.4.1.5
The information transfer rate.
OBJECT-TYPE    
  INTEGER packet(1), r-64k(17), r-2x64k(18), r-384k(20), r-1536k(22), r-1920k(24)  

accIsdnCallState 1.3.6.1.4.1.5.1.1.36.4.1.6
The current call control state (not Q.931).
OBJECT-TYPE    
  INTEGER disconnected(1), incoming(2), outgoing(3), routing(4), releaseing(5), connected(6)  

accIsdnCallCause 1.3.6.1.4.1.5.1.1.36.4.1.7
The last cause value associated with this call.
OBJECT-TYPE    
  INTEGER 0..255  

accIsdnCallOrigin 1.3.6.1.4.1.5.1.1.36.4.1.8
The originator of the call.
OBJECT-TYPE    
  INTEGER none(1), terminal(2), network(3)  

accIsdnCallAddress 1.3.6.1.4.1.5.1.1.36.4.1.9
The remote call address associated with this call. For incoming calls, this is the calling ISDN address. For outgoing calls, this is the called ISDN address.
OBJECT-TYPE    
  OCTET STRING  

accIsdnCallDslIndex 1.3.6.1.4.1.5.1.1.36.4.1.10
The interface index for the digital subscriber loop.
OBJECT-TYPE    
  INTEGER 1..255  

accIsdnTest 1.3.6.1.4.1.5.1.1.36.5
OBJECT IDENTIFIER    

accIsdnTestIfIndex 1.3.6.1.4.1.5.1.1.36.5.1
The interface index for the physical port from which a call will be made.
OBJECT-TYPE    
  INTEGER j1(1), j2(2)  

accIsdnTestAddress 1.3.6.1.4.1.5.1.1.36.5.2
The ISDN destination call address.
OBJECT-TYPE    
  OCTET STRING  

accIsdnTestCommand 1.3.6.1.4.1.5.1.1.36.5.3
The action to be performed.
OBJECT-TYPE    
  INTEGER normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), loop(8), unloop(9), activate(10), deactivate(11), display(12)  

accIsdnTestRouting 1.3.6.1.4.1.5.1.1.36.5.4
The action to be performed for incoming calls.
OBJECT-TYPE    
  INTEGER normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), activate(8), deactivate(9), loop4(10), reset(11), display(12), ones(13), zeros(14), bon(15), boff(16)  

accIsdnTestRegName 1.3.6.1.4.1.5.1.1.36.5.5
The name of the MC145474 register to write.
OBJECT-TYPE    
  INTEGER nr0(0), nr1(1), nr2(2), nr3(3), nr4(4), nr5(5), nr6(6), br0(16), br1(17), br2(18), br3(19), br4(20), br5(21), br6(22), br7(23), br8(24), br9(25), br10(26), br11(27), br12(28), br13(29), br14(30), br15(31)  

accIsdnTestRegValue 1.3.6.1.4.1.5.1.1.36.5.6
The value to write to the MC145474 register.
OBJECT-TYPE    
  INTEGER 0..255  

accwIsdnTestBChanMode 1.3.6.1.4.1.5.1.1.36.5.7
The action to be performed on the B-channel.
OBJECT-TYPE    
  INTEGER normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), activate(8), deactivate(9), loop4(10), reset(11), display(12), ones(13), zeros(14), bon(15), boff(16)  

accwIsdnTestOptions 1.3.6.1.4.1.5.1.1.36.5.8
Test options in hex.
OBJECT-TYPE    
  INTEGER  

accIsdnxSubTable 1.3.6.1.4.1.5.1.1.36.6
ISDN subscriber table containing configuration and operational parameters for all ISDN subscriber interfaces on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnxSubEntry

accIsdnxSubEntry 1.3.6.1.4.1.5.1.1.36.6.1
An entry in the ISDN Subscriber Table
OBJECT-TYPE    
  AccIsdnxSubEntry  

accIsdnxSubDslIndex 1.3.6.1.4.1.5.1.1.36.6.1.1
The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device.
OBJECT-TYPE    
  INTEGER  

accIsdnxSubSwitchType 1.3.6.1.4.1.5.1.1.36.6.1.2
The particular type of central-office switch providing access to the ISDN network and to which this subscriber interface is connected.
OBJECT-TYPE    
  INTEGER bri-net3(1), bri-5ess(2), bri-dms100(3), bri-vn2(4), bri-vn3(5), bri-kdd(6), bri-ntt(7), bri-1tr6(8), bri-ni1(9), bri-ccitt(10), bri-tad2(11), bri-ts013(12), bri-ni2(13), pri-4ess(14), pri-5ess(15), pri-dms100(16), pri-net5(17), pri-vn3(18), pri-kdd(19), pri-ntt(20), pri-1tr6(21), pri-ccitt(22), pri-tad30(23), pri-ts014(24), pri-ni2(25), bri-auto-na(26)  

accIsdnxSubChanConfig 1.3.6.1.4.1.5.1.1.36.6.1.3
The ISDN channel configuration mode. Beginning with release 8.0, this is the number of bearer channels managed by the D channel. This object is normally read-only. It can be written only when changing the channel configuration from 2B+D to 1B+D on a Nile configured with a BRI in J1.
OBJECT-TYPE    
  INTEGER 1..255  

accIsdnxSubAdminStatus 1.3.6.1.4.1.5.1.1.36.6.1.4
The administrative status of this subscriber interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), drain(3)  

accIsdnxSubDiagLevel 1.3.6.1.4.1.5.1.1.36.6.1.5
The current diagnostic message level for this subscriber interface.
OBJECT-TYPE    
  INTEGER 0..6  

accIsdnxSubManualTei 1.3.6.1.4.1.5.1.1.36.6.1.6
The TEI (terminal endpoint identifier) when manual TEI assignment is required. Setting this value between 0 and 63 (inclusive) specifies manual TEI assignment using the indicated value. Setting this value to 127 (the broadcast TEI) specifies automatic TEI assignment. This object is writable only for BRI subscribers. For PRI subscribers, the value read is always 0
OBJECT-TYPE    
  INTEGER 0..63  

accIsdnxSubOperStatus 1.3.6.1.4.1.5.1.1.36.6.1.7
The operational status of this subscriber interface.
OBJECT-TYPE    
  INTEGER deactivated(1), activated(2), established(3), engaged(4)  

accIsdnxSubNumNfas 1.3.6.1.4.1.5.1.1.36.6.1.8
Indicates the number of NFAS trunks managed by this D channel.
OBJECT-TYPE    
  INTEGER 0..255  

accIsdnxSubLastCause 1.3.6.1.4.1.5.1.1.36.6.1.9
The last clearing cause for a call associated with this interface.
OBJECT-TYPE    
  INTEGER 0..255  

accIsdnxSubSubaddrType 1.3.6.1.4.1.5.1.1.36.6.1.10
Indicates the subaddress type for the ISDN interface.
OBJECT-TYPE    
  INTEGER nsap(1), user(2)  

accIsdnxSubVoiceOption 1.3.6.1.4.1.5.1.1.36.6.1.11
Indicates whether the user is able to receive circuit mode voice calls
OBJECT-TYPE    
  INTEGER on(1), off(2)  

accIsdnxSubCliOption 1.3.6.1.4.1.5.1.1.36.6.1.12
Indicates whether a callers identifaction will be checked with known entries before accepting the call.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

accIsdnxSubEncodingMethod 1.3.6.1.4.1.5.1.1.36.6.1.13
Companding algorithm to be used when initiating or answering voice calls over this interface. This is configured during initialization based on the user configured switch type.
OBJECT-TYPE    
  INTEGER a-law(1), mu-law(2)  

accIsdnxSubDialingMethod 1.3.6.1.4.1.5.1.1.36.6.1.14
Dialing method to be used when initiating voice calls over the ISDN line. This is configured during initialization based on the user configured switch type.
OBJECT-TYPE    
  INTEGER overlap(1), enbloc(2)  

accIsdnxSubAutoSpid 1.3.6.1.4.1.5.1.1.36.6.1.19
SR-3888 Automatic SPID detection enabled or disabled for a BRI subscriber interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accIsdnxSubAutoSwitch 1.3.6.1.4.1.5.1.1.36.6.1.20
The central-office switch type detected by the Automatic Switch detection function.
OBJECT-TYPE    
  INTEGER unknown(1), manual(2), bri-ni1(3), bri-5ess(4), bri-dms100(5)  

accIsdnxStatTable 1.3.6.1.4.1.5.1.1.36.7
Statistics and operational status maintained for all ISDN subscriber interfaces on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnxStatEntry

accIsdnxStatEntry 1.3.6.1.4.1.5.1.1.36.7.1
An entry in the ISDN Statistics Table.
OBJECT-TYPE    
  AccIsdnxStatEntry  

accIsdnxStatDslIndex 1.3.6.1.4.1.5.1.1.36.7.1.1
The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device.
OBJECT-TYPE    
  INTEGER  

accIsdnxStatHdlcInPackets 1.3.6.1.4.1.5.1.1.36.7.1.2
The number of packets received on the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcInOctets 1.3.6.1.4.1.5.1.1.36.7.1.3
The number of octets received on the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcInErrors 1.3.6.1.4.1.5.1.1.36.7.1.4
The number of input hardware errors counted by the D-channel HDLC driver.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcInDiscards 1.3.6.1.4.1.5.1.1.36.7.1.5
The number of input packets discarded by the D-channel HDLC driver.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcOutPackets 1.3.6.1.4.1.5.1.1.36.7.1.6
The number of packets transmitted on the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcOutOctets 1.3.6.1.4.1.5.1.1.36.7.1.7
The number of octets transmitted on the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcOutErrors 1.3.6.1.4.1.5.1.1.36.7.1.8
The number of output hardware errors counted by the D-channel HDLC driver.
OBJECT-TYPE    
  Counter  

accIsdnxStatHdlcOutDiscards 1.3.6.1.4.1.5.1.1.36.7.1.9
The number of output packets discarded by the D-channel HDLC driver.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdUnsolicResps 1.3.6.1.4.1.5.1.1.36.7.1.10
The number of unsolicited LAPD response frames received on all data links associated with the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdPeerSabmes 1.3.6.1.4.1.5.1.1.36.7.1.11
The number of peer SABME frames received on all data links associated with the D-channel of this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdN200Errors 1.3.6.1.4.1.5.1.1.36.7.1.12
The number of unsuccessful T200 timer recoveries after a frame has been retransmitted N200 times.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdNrSeqErrors 1.3.6.1.4.1.5.1.1.36.7.1.13
The number of N(R) sequence errors.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdRecvdFrmrs 1.3.6.1.4.1.5.1.1.36.7.1.14
The number of LAPD FRMR response frames received.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdCntlErrors 1.3.6.1.4.1.5.1.1.36.7.1.15
The number of LAPD frames received with an invalid or non-implemented control field.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdInfoErrors 1.3.6.1.4.1.5.1.1.36.7.1.16
The number of LAPD frames received with a non-permitted information (I) field.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdWrongSizes 1.3.6.1.4.1.5.1.1.36.7.1.17
The number of LAPD frames received which were the wrong size.
OBJECT-TYPE    
  Counter  

accIsdnxStatLapdN201Errors 1.3.6.1.4.1.5.1.1.36.7.1.18
The number of LAPD frames received which contained and information field which exceeded N201.
OBJECT-TYPE    
  Counter  

accIsdnxStatCallOriginateds 1.3.6.1.4.1.5.1.1.36.7.1.19
The number of outgoing calls originated on this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatCallOfferreds 1.3.6.1.4.1.5.1.1.36.7.1.20
The number of incoming calls offered on this ISDN interface.
OBJECT-TYPE    
  Counter  

accIsdnxStatCallRouteds 1.3.6.1.4.1.5.1.1.36.7.1.21
The number of outgoing calls originated on this ISDN interface which were routed by the network.
OBJECT-TYPE    
  Counter  

accIsdnxStatCallAccepteds 1.3.6.1.4.1.5.1.1.36.7.1.22
The number of incoming calls offered on this ISDN interface which were accepted for connection.
OBJECT-TYPE    
  Counter  

accIsdnxStatCallCompleteds 1.3.6.1.4.1.5.1.1.36.7.1.23
The number of outgoing and incoming calls completed (that is, the number of calls which were successfully connected).
OBJECT-TYPE    
  Counter  

accIsdnxStatCallCleareds 1.3.6.1.4.1.5.1.1.36.7.1.24
The number of outgoing and incoming calls cleared.
OBJECT-TYPE    
  Counter  

accIsdnxCallTable 1.3.6.1.4.1.5.1.1.36.8
Parameters and operational status for ISDN calls in progress on this bridge/router terminal.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnxCallEntry

accIsdnxCallEntry 1.3.6.1.4.1.5.1.1.36.8.1
An entry in the ISDN Call Table.
OBJECT-TYPE    
  AccIsdnxCallEntry  

accIsdnxCallDslIndex 1.3.6.1.4.1.5.1.1.36.8.1.1
The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device.
OBJECT-TYPE    
  INTEGER  

accIsdnxCallReference 1.3.6.1.4.1.5.1.1.36.8.1.2
The Q.931 call reference value for this call.
OBJECT-TYPE    
  INTEGER 1..32767  

accIsdnxCallOrigin 1.3.6.1.4.1.5.1.1.36.8.1.3
The originator of the call.
OBJECT-TYPE    
  INTEGER none(1), terminal(2), network(3)  

accIsdnxCallCircuitIndex 1.3.6.1.4.1.5.1.1.36.8.1.4
The ifIndex for the circuit associated with this call.
OBJECT-TYPE    
  INTEGER  

accIsdnxCallInfoRate 1.3.6.1.4.1.5.1.1.36.8.1.5
The information transfer rate.
OBJECT-TYPE    
  INTEGER info-rate-1x64k(1), info-rate-2x64k(2), info-rate-3x64k(3), info-rate-4x64k(4), info-rate-5x64k(5), info-rate-6x64k(6), info-rate-7x64k(7), info-rate-8x64k(8), info-rate-9x64k(9), info-rate-10x64k(10), info-rate-11x64k(11), info-rate-12x64k(12), info-rate-13x64k(13), info-rate-14x64k(14), info-rate-15x64k(15), info-rate-16x64k(16), info-rate-17x64k(17), info-rate-18x64k(18), info-rate-19x64k(19), info-rate-20x64k(20), info-rate-21x64k(21), info-rate-22x64k(22), info-rate-23x64k(23), info-rate-24x64k(24), info-rate-25x64k(25), info-rate-26x64k(26), info-rate-27x64k(27), info-rate-28x64k(28), info-rate-29x64k(29), info-rate-30x64k(30), info-rate-31x64k(31), packet(32)  

accIsdnxCallState 1.3.6.1.4.1.5.1.1.36.8.1.6
The Q.931 call control state.
OBJECT-TYPE    
  INTEGER idle(1), initiated(2), overlap-send(3), outgoing(4), delivered(5), present(6), received(7), connecting(8), incoming(9), active(10), discon-req(11), discon-ind(12), suspend(13), resume(14), release(15), overlap-recv(16)  

accIsdnxCallCause 1.3.6.1.4.1.5.1.1.36.8.1.7
The last cause value associated with this call.
OBJECT-TYPE    
  INTEGER 0..255  

accIsdnxCallAddress 1.3.6.1.4.1.5.1.1.36.8.1.8
The remote call address associated with this call. For incoming calls, this is the calling ISDN address. For outgoing calls, this is the called ISDN address.
OBJECT-TYPE    
  OCTET STRING  

accIsdnxCallInfoType 1.3.6.1.4.1.5.1.1.36.8.1.9
The information transfer type: info-type-cmd circuit mode data, clear channel 64 kbits/s info-type-cm56 circuit mode data, rate-adapted to 56 kbits/s info-type-cmv circuit mode data over voice circuit
OBJECT-TYPE    
  INTEGER info-type-cmd(1), info-type-cm56(2), info-type-cmv(3)  

accIsdnxCallSlotMap 1.3.6.1.4.1.5.1.1.36.8.1.10
A 31-bit mask which identifies the time-slots forming a hyperchannel.
OBJECT-TYPE    
  INTEGER  

accIsdnSpidTable 1.3.6.1.4.1.5.1.1.36.9
Valid SPIDs currently Registered with the CO, required for placing/accepting calls.
OBJECT-TYPE    
  SEQUENCE OF  
    AccIsdnSpidEntry

accIsdnSpidEntry 1.3.6.1.4.1.5.1.1.36.9.1
SPID information entry in the SPID Table.
OBJECT-TYPE    
  AccIsdnSpidEntry  

accIsdnSpidIndex 1.3.6.1.4.1.5.1.1.36.9.1.1
An Index to Ports of B-channels.
OBJECT-TYPE    
  INTEGER  

accIsdnSpidValue 1.3.6.1.4.1.5.1.1.36.9.1.2
Value of SPID,Required for the terminal to be active on the S/T bus.
OBJECT-TYPE    
  DisplayString  

accIsdnTerm 1.3.6.1.4.1.5.1.1.36.10
OBJECT IDENTIFIER    

accIsdnxTermination 1.3.6.1.4.1.5.1.1.36.10.1
ISDN Bus Termination status
OBJECT-TYPE    
  INTEGER on(1), off(2)  

accIsdnxCurrCalls 1.3.6.1.4.1.5.1.1.36.11
Number of active ISDN calls
OBJECT-TYPE    
  INTEGER  

accIsdnTraps 1.3.6.1.4.1.5.1.1.36.12
OBJECT IDENTIFIER    

accIsdnTrapMsg 1.3.6.1.4.1.5.1.1.36.12.1
ISDN Trap Message
OBJECT-TYPE    
  DisplayString  

accIsdnOutGoingCallTrap 1.3.6.1.4.1.5.1.1.36.12.1
While initializing the call control block. When the call was first originated to establish the correct connection endpoint specifier to use, there is a check on failing which this trap is generated SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnCallResetTrap 1.3.6.1.4.1.5.1.1.36.12.2
When a catestrophic event occurs, if there is no recovery because of less cblks, then the call is simply forced to clear, which is cause for this call reset trap SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnConnectTrap 1.3.6.1.4.1.5.1.1.36.12.3
Indication thruough this trap is a failure of Connect if the ICCB channel is present. Else deicdes there is no bearer channel and sends this trap. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnStaleDialCntxtTrap 1.3.6.1.4.1.5.1.1.36.12.4
This trap is triggered when there is a mismatch in the Magicnumber. Treating it as a stale dial. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnIncomingCallTrap 1.3.6.1.4.1.5.1.1.36.12.5
This is generated during identifying the calling party, if the call has to be refused based on the validity of the calling number. The reason is also stated in the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnCallTrap 1.3.6.1.4.1.5.1.1.36.12.6
This is generated during identifying the called party, if the call has to be refused based on the validity of the called number. The reason is also stated in the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnApplTmrExpTrap 1.3.6.1.4.1.5.1.1.36.12.7
If the application timer expires during the call setup, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnApplTmrExpInClearTrap 1.3.6.1.4.1.5.1.1.36.12.8
If the application timer expires during the call clearing, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnChannelRestrtTrap 1.3.6.1.4.1.5.1.1.36.12.9
While determining valid the channel stat, if the action is to restart the channel, then the appropriate B-Channel is restarted. This trap indicates such a situation. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnDataLnkRelTrap 1.3.6.1.4.1.5.1.1.36.12.10
If the D-channel Data Link is is to be released making Datalink down, then this trap is triggered. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 108
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeverityType  
  accTrapLogSeqNum  

accIsdnDataLnkEstTrap 1.3.6.1.4.1.5.1.1.36.12.11
If the D-Channel Data Link is established making Datalink UP, then this trap is triggered. SEVERITY-DEFAULT: Clear EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 108
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeverityType  
  accTrapLogSeqNum  

accIsdnConfigStackTrap 1.3.6.1.4.1.5.1.1.36.12.12
If the ISDN stack cannot be configured because of reasons like unspecified switch type, or not supporting DCBU etc., then this trap is generated which is conveying that a configuration error has occured. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnSubscriberLoopTrap 1.3.6.1.4.1.5.1.1.36.12.13
When a catestorphic error like low cblk conditions occur, then it tries to recover by restting the subscriber's loop. That is when this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnRegisterTrap 1.3.6.1.4.1.5.1.1.36.12.14
If the registration name is not identified and found in the list, then it sends this trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnTrmnlRegErrTrap 1.3.6.1.4.1.5.1.1.36.12.15
If there is a error in getting the SPID indicates that the it is a unknown CES or may be a inoppurtune event has occured and hence the terminal registration error is sent. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnTrmnlRegTrap 1.3.6.1.4.1.5.1.1.36.12.16
In the event SPID state being pending indicates that the the terminal registration failed. This trap indicates the same. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAwaitDatalnkEstTrap 1.3.6.1.4.1.5.1.1.36.12.17
If the SME_TERM_REGISTER request is apparently stuck, most likely because a datalink cannot be established, then this trap is generated. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnDisconnectTrap 1.3.6.1.4.1.5.1.1.36.12.18
If the CCB state is proceeding and the ISDN CHANNEL ID is none then this trap can be triggered after which the call is abort. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnOutGoingCallFailTrap 1.3.6.1.4.1.5.1.1.36.12.19
In the process of disconnect request from the RM Manager if there isn't any active call, then this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnTrap20 1.3.6.1.4.1.5.1.1.36.12.20
If the RM Dial manger sends the request to set up and if it fails for various reason, then this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnModuleErrTrap 1.3.6.1.4.1.5.1.1.36.12.21
If the application timer expires during the call setup, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnTrap22 1.3.6.1.4.1.5.1.1.36.12.22
If the application timer expires during the call clrearing, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnNfasIntfTrap 1.3.6.1.4.1.5.1.1.36.12.23
If there is a application-dependent error then this trap displays the module function and the error message. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnNoSpidTrap 1.3.6.1.4.1.5.1.1.36.12.24
While initialsing the layer1 task, if the interface is configured for NT mode, then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnSpidConflictTrap 1.3.6.1.4.1.5.1.1.36.12.25
If the trial to get the internal interface id fails it means the NFAS interface is not properly defined. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnInvSpidTrap 1.3.6.1.4.1.5.1.1.36.12.26
While getting the SPID tries to find the port. In the process if the port is not found and a corresponding PP index is not found then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnSwBldTrap 1.3.6.1.4.1.5.1.1.36.12.27
While getting the SPID, it comapres the interface flag and if there is a match, it triggers a config error, and hence the trap saying conflicting SPIDs. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnParametersTrap 1.3.6.1.4.1.5.1.1.36.12.28
If the SPID is too lengthy which is not supported then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnSwitchTypeTrap 1.3.6.1.4.1.5.1.1.36.12.29
Determines whether or not operating as the network side (NT) or user side (TE) and records this in the DSL entry. And generates a trap if the hardware configuration is not consistent with the software system build (Telenetworks requires USER vs. NETWORK to be bound at compile-time). SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnManyIntfTrap 1.3.6.1.4.1.5.1.1.36.12.30
While initialzing the ISDN parameters, it validates from the NVM. While doing so if a error is encountered this config error trap is sent. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnPriGroupRangeTrap 1.3.6.1.4.1.5.1.1.36.12.31
Tries to make sure the switch type configured for the subscriber entry has been included in the system build. If not, generates this trap and proceeds as if the entry had been disabled. Also, makes sure the switch type is consistent with the installed interface. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnNfasIntfPriTrap 1.3.6.1.4.1.5.1.1.36.12.32
The maximum number of DSL entries is limited at compile time by the Telenetworks code. When it exceeds this this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnManyNFASIntfTrap 1.3.6.1.4.1.5.1.1.36.12.33
If during initialization a invalid group is encountered as it is out of the range, then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnPriGroupTrap 1.3.6.1.4.1.5.1.1.36.12.34
Looks for interfaces in PRI group 0. If the interface has a signaling channel, it is assumed to be a stand-alone interface. Otherwise, it is a orphan (i.e., misconfigured) NFAS interface, hence generates the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnTrap35 1.3.6.1.4.1.5.1.1.36.12.35
In the event of making sure the PRI group has a primary signaling interface and that the group can accommodate an additional NFAS interface, if the new pri id or secondary new id exceed the maximum interface id, this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnNoSrvcProIFTrap 1.3.6.1.4.1.5.1.1.36.12.36
No service profile identifier SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnNTBldIncmptblHWTrap 1.3.6.1.4.1.5.1.1.36.12.37
Software NT build is incompatible with harware TE mode SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnRcvdSpidTrap 1.3.6.1.4.1.5.1.1.36.12.38
Received one spid SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accIsdnSpidValue  
  accTrapLogSeqNum  

accIsdnRcvdSpidsNWTrap 1.3.6.1.4.1.5.1.1.36.12.39
Received spids from network SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accIsdnSpidValue  
  accTrapLogSeqNum  

accIsdnAutoSpidFldTrap 1.3.6.1.4.1.5.1.1.36.12.40
Auto spid failed (found %d suitable SPID(s)) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAutoSpidSccdTrap 1.3.6.1.4.1.5.1.1.36.12.41
Auto spid succeeded SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAutoSpidFld1Trap 1.3.6.1.4.1.5.1.1.36.12.42
Auto spid failed (cause = %d) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAutoSwtchSccdTrap 1.3.6.1.4.1.5.1.1.36.12.43
Auto switch detection succeeded SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAutoSwtchFldTrap 1.3.6.1.4.1.5.1.1.36.12.44
Auto switch detection failed (unspecified switch type) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

accIsdnAutoSwtchFld1Trap 1.3.6.1.4.1.5.1.1.36.12.45
Auto switch detection failed SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    
  accIsdnTrapMsg  
  accTrapLogSeqNum  

Defined Objects

AccIsdnSubEntry  
SEQUENCE    
  INTEGER as accIsdnSubSwitchType  
  INTEGER as accIsdnSubChannelMode  
  INTEGER as accIsdnSubAdminStatus  
  INTEGER as accIsdnSubDiagLevel  
  INTEGER as accIsdnSubManualTei  

AccIsdnStatEntry  
SEQUENCE    
  Counter as accIsdnStatHdlcInPackets  
  Counter as accIsdnStatHdlcInOctets  
  Counter as accIsdnStatHdlcInErrors  
  Counter as accIsdnStatHdlcInDiscs  
  Counter as accIsdnStatHdlcOutPackets  
  Counter as accIsdnStatHdlcOutOctets  
  Counter as accIsdnStatHdlcOutErrors  
  Counter as accIsdnStatHdlcOutDiscs  
  Counter as accIsdnStatLapdUnsolicResps  
  Counter as accIsdnStatLapdPeerSabmes  
  Counter as accIsdnStatLapdN200Errors  
  Counter as accIsdnStatLapdNrSeqErrors  
  Counter as accIsdnStatLapdRecvdFrmrs  
  Counter as accIsdnStatLapdCntlErrors  
  Counter as accIsdnStatLapdInfoErrors  
  Counter as accIsdnStatLapdWrongSizes  
  Counter as accIsdnStatLapdN201Errors  
  Counter as accIsdnStatCallsOriginateds  
  Counter as accIsdnStatCallsOfferreds  
  Counter as accIsdnStatCallsAnswereds  
  Counter as accIsdnStatCallsAccepteds  
  Counter as accIsdnStatCallsCompleteds  
  Counter as accIsdnStatCallsCleareds  
  INTEGER as accIsdnStatDslOperStatus  
  INTEGER as accIsdnStatLastCauses  

AccIsdnCallEntry  
SEQUENCE    
  INTEGER as accIsdnCallIdentifier  
  INTEGER as accIsdnCallReference  
  INTEGER as accIsdnCallChannelId  
  INTEGER as accIsdnCallIfIndex  
  INTEGER as accIsdnCallInfoRate  
  INTEGER as accIsdnCallState  
  INTEGER as accIsdnCallCause  
  INTEGER as accIsdnCallOrigin  
  OCTET STRING as accIsdnCallAddress  
  INTEGER as accIsdnCallDslIndex  

AccIsdnxSubEntry  
SEQUENCE    
  INTEGER as accIsdnxSubDslIndex  
  INTEGER as accIsdnxSubSwitchType  
  INTEGER as accIsdnxSubChanConfig  
  INTEGER as accIsdnxSubAdminStatus  
  INTEGER as accIsdnxSubDiagLevel  
  INTEGER as accIsdnxSubManualTei  
  INTEGER as accIsdnxSubOperStatus  
  INTEGER as accIsdnxSubNumNfas  
  INTEGER as accIsdnxSubLastCause  
  INTEGER as accIsdnxSubSubaddrType  
  INTEGER as accIsdnxSubVoiceOption  
  INTEGER as accIsdnxSubCliOption  
  INTEGER as accIsdnxSubEncodingMethod  
  INTEGER as accIsdnxSubDialingMethod  
  INTEGER as accIsdnxSubAutoSpid  
  INTEGER as accIsdnxSubAutoSwitch  

AccIsdnxStatEntry  
SEQUENCE    
  INTEGER as accIsdnxStatDslIndex  
  Counter as accIsdnxStatHdlcInPackets  
  Counter as accIsdnxStatHdlcInOctets  
  Counter as accIsdnxStatHdlcInErrors  
  Counter as accIsdnxStatHdlcInDiscards  
  Counter as accIsdnxStatHdlcOutPackets  
  Counter as accIsdnxStatHdlcOutOctets  
  Counter as accIsdnxStatHdlcOutErrors  
  Counter as accIsdnxStatHdlcOutDiscards  
  Counter as accIsdnxStatLapdUnsolicResps  
  Counter as accIsdnxStatLapdPeerSabmes  
  Counter as accIsdnxStatLapdN200Errors  
  Counter as accIsdnxStatLapdNrSeqErrors  
  Counter as accIsdnxStatLapdRecvdFrmrs  
  Counter as accIsdnxStatLapdCntlErrors  
  Counter as accIsdnxStatLapdInfoErrors  
  Counter as accIsdnxStatLapdWrongSizes  
  Counter as accIsdnxStatLapdN201Errors  
  Counter as accIsdnxStatCallOriginateds  
  Counter as accIsdnxStatCallOfferreds  
  Counter as accIsdnxStatCallRouteds  
  Counter as accIsdnxStatCallAccepteds  
  Counter as accIsdnxStatCallCompleteds  
  Counter as accIsdnxStatCallCleareds  

AccIsdnxCallEntry  
SEQUENCE    
  INTEGER as accIsdnxCallDslIndex  
  INTEGER as accIsdnxCallReference  
  INTEGER as accIsdnxCallOrigin  
  INTEGER as accIsdnxCallCircuitIndex  
  INTEGER as accIsdnxCallInfoRate  
  INTEGER as accIsdnxCallState  
  INTEGER as accIsdnxCallCause  
  OCTET STRING as accIsdnxCallAddress  
  INTEGER as accIsdnxCallInfoType  
  INTEGER as accIsdnxCallSlotMap  

AccIsdnSpidEntry  
SEQUENCE    
  INTEGER as accIsdnSpidIndex  
  DisplayString as accIsdnSpidValue