
| SNMPv2-TC | SNMPv2-SMI | RFC1213-MIB |
| SNMP-FRAMEWORK-MIB | DLINK-ID-REC-MIB |
| TEXTUAL-CONVENTION | Counter32 | Counter64 |
| TimeTicks | NOTIFICATION-TYPE | MODULE-IDENTITY |
| OBJECT-TYPE | IpAddress | Unsigned32 |
| MacAddress | RowStatus | DisplayString |
| SnmpAdminString | dlink-common-mgmt |
| swAclMgmtMIB | 1.3.6.1.4.1.171.12.9 | ||
| The Structure of Access Control List Information for the proprietary enterprise. | |||
| MODULE-IDENTITY | |||
| swAclMaskMgmt | 1.3.6.1.4.1.171.12.9.1 | ||
| OBJECT IDENTIFIER | |||
| swACLEthernetTable | 1.3.6.1.4.1.171.12.9.1.1 | ||
| This table contain ACL mask of Ethernet information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's layer 2 part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLEthernetEntry | |||
| swACLEthernetEntry | 1.3.6.1.4.1.171.12.9.1.1.1 | ||
| A list of information about ACL of Ethernet. | |||
| OBJECT-TYPE | |||
| SwACLEthernetEntry | |||
| swACLEthernetProfileID | 1.3.6.1.4.1.171.12.9.1.1.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLEthernetUsevlan | 1.3.6.1.4.1.171.12.9.1.1.1.2 | ||
| Specifies that the switch will examine the VLAN part of each packet header. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEthernetMacAddrMaskState | 1.3.6.1.4.1.171.12.9.1.1.1.3 | ||
| This object indicates the status of MAC address mask. other(1) - Neither source MAC address nor destination MAC address are masked. dst-mac-addr(2) - recieved frames's destination MAC address are currently used to be filtered as it meets with the MAC address entry of the table. src-mac-addr(3) - recieved frames's source MAC address are currently used to be filtered as it meets with the MAC address entry of the table. dst-src-mac-addr(4) - recieved frames's destination MAC address or source MAC address are currently used to be filtered as it meets with the MAC address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-mac-addr(2), src-mac-addr(3), dst-src-mac-addr(4) | ||
| swACLEthernetSrcMacAddrMask | 1.3.6.1.4.1.171.12.9.1.1.1.4 | ||
| This object Specifies the MAC address mask for the source MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swACLEthernetDstMacAddrMask | 1.3.6.1.4.1.171.12.9.1.1.1.5 | ||
| This object Specifies the MAC address mask for the destination MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swACLEthernetUse8021p | 1.3.6.1.4.1.171.12.9.1.1.1.6 | ||
| Specifies if the switch will examine the 802.1p priority value in the frame's header or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEthernetUseEthernetType | 1.3.6.1.4.1.171.12.9.1.1.1.7 | ||
| Specifies if the switch will examine the Ethernet type value in each frame's header or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEthernetRowStatus | 1.3.6.1.4.1.171.12.9.1.1.1.8 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLEthernetOwner | 1.3.6.1.4.1.171.12.9.1.1.1.9 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLIpTable | 1.3.6.1.4.1.171.12.9.1.2 | ||
| This table contain ACL mask of IP information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's IP layer part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLIpEntry | |||
| swACLIpEntry | 1.3.6.1.4.1.171.12.9.1.2.1 | ||
| A list of information about ACL of IP Layer. | |||
| OBJECT-TYPE | |||
| SwACLIpEntry | |||
| swACLIpProfileID | 1.3.6.1.4.1.171.12.9.1.2.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLIpUsevlan | 1.3.6.1.4.1.171.12.9.1.2.1.2 | ||
| This object indicates if IP layer vlan is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpIpAddrMaskState | 1.3.6.1.4.1.171.12.9.1.2.1.3 | ||
| This object indicates the status of IP address mask. other(1) - Neither source IP address nor destination IP address are masked. dst-ip-addr(2) - recieved frames's destination IP address are currently used to be filtered as it meets with the IP address entry of the table. src-ip-addr(3) - recieved frames's source IP address are currently used to be filtered as it meets with the IP address entry of the table. dst-src-ip-addr(4) - recieved frames's destination IP address or source IP address are currently used to be filtered as it meets with the IP address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-ip-addr(2), src-ip-addr(3), dst-src-ip-addr(4) | ||
| swACLIpSrcIpAddrMask | 1.3.6.1.4.1.171.12.9.1.2.1.4 | ||
| This object Specifies IP address mask for the source IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swACLIpDstIpAddrMask | 1.3.6.1.4.1.171.12.9.1.2.1.5 | ||
| This object Specifies the IP address mask for the destination IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swACLIpUseDSCP | 1.3.6.1.4.1.171.12.9.1.2.1.6 | ||
| This object indicates DSCP protocol is is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpUseProtoType | 1.3.6.1.4.1.171.12.9.1.2.1.7 | ||
| That object indicates which protocol will be examined. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6) | ||
| swACLIpIcmpOption | 1.3.6.1.4.1.171.12.9.1.2.1.8 | ||
| This object indicates which fields should be filled in of ICMP. none(1)- two fields are null. type(2)- type field should be filled in. code(3)- code field should be filled in. type-code(4)- not only type fileld but code field should be filled in. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), type(2), code(3), type-code(4) | ||
| swACLIpIgmpOption | 1.3.6.1.4.1.171.12.9.1.2.1.9 | ||
| This object indicates Options of IGMP is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swACLIpTcpOption | 1.3.6.1.4.1.171.12.9.1.2.1.10 | ||
| This object indicates the status of filtered address of TCP. other(1) - Neither source port nor destination port are masked. dst-addr(2) - recieved frames's destination port are currently used to be filtered . src-addr(3) - recieved frames's source port are currently used to be filtered . dst-src-addr(4) - both recieved frames's destination port and source port are currently used to be filtered . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4) | ||
| swACLIpUdpOption | 1.3.6.1.4.1.171.12.9.1.2.1.11 | ||
| This object indicates the status of filtered address of UDP . other(1) - Neither source port nor destination port are masked. dst-addr(2) - recieved frames's destination port are currently used to be filtered . src-addr(3) - recieved frames's source port are currently used to be filtered . dst-src-addr(4) - recieved frames's destination port or source port are currently used to be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4) | ||
| swACLIpTCPorUDPSrcPortMask | 1.3.6.1.4.1.171.12.9.1.2.1.12 | ||
| Specifies a TCP port mask for the source port if swACLIpUseProtoType is TCP Specifies a UDP port mask for the source port if swACLIpUseProtoType is UDP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swACLIpTCPorUDPDstPortMask | 1.3.6.1.4.1.171.12.9.1.2.1.13 | ||
| Specifies a TCP port mask for the destination port if swACLIpUseProtoType is TCP Specifies a UDP port mask for the destination port if swACLIpUseProtoType is UDP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swACLIpTCPFlagBit | 1.3.6.1.4.1.171.12.9.1.2.1.14 | ||
| Specifies a TCP connection flag mask. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swACLIpTCPFlagBitMask | 1.3.6.1.4.1.171.12.9.1.2.1.15 | ||
| A value which indicates the set of TCP flags that this entity may potentially offers. The value is a sum. This sum initially takes the value zero, Then, for each flag, L, in the range 1 through 6, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example,it you want to enable urg bit and ack bit,you should set vlaue 48(2^(5-1) + 2^(6-1)). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLIpProtoIDOption | 1.3.6.1.4.1.171.12.9.1.2.1.16 | ||
| Specifies that the switch will examine each frame's Protocol ID field or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swACLIpProtoID | 1.3.6.1.4.1.171.12.9.1.2.1.17 | ||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swACLIpProtoIDMask | 1.3.6.1.4.1.171.12.9.1.2.1.18 | ||
| Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(20) | ||
| swACLIpRowStatus | 1.3.6.1.4.1.171.12.9.1.2.1.19 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLIpOwner | 1.3.6.1.4.1.171.12.9.1.2.1.20 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLPktContMaskTable | 1.3.6.1.4.1.171.12.9.1.3 | ||
| This table contain ACL mask of user-defined information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's user-defined part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLPktContMaskEntry | |||
| swACLPktContMaskEntry | 1.3.6.1.4.1.171.12.9.1.3.1 | ||
| A list of information about ACL of user-defined. | |||
| OBJECT-TYPE | |||
| SwACLPktContMaskEntry | |||
| swACLPktContMaskProfileID | 1.3.6.1.4.1.171.12.9.1.3.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLPktContMaskOffset0to15 | 1.3.6.1.4.1.171.12.9.1.3.1.2 | ||
| Specifies that the rule applies to the packet content(Offset0to15) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContMaskOffset16to31 | 1.3.6.1.4.1.171.12.9.1.3.1.3 | ||
| Specifies that the rule applies to the packet content(Offset16to31) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContMaskOffset32to47 | 1.3.6.1.4.1.171.12.9.1.3.1.4 | ||
| Specifies that the rule applies to the packet content(Offset32to47) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContMaskOffset48to63 | 1.3.6.1.4.1.171.12.9.1.3.1.5 | ||
| Specifies that the rule applies to the packet content(Offset48to63) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContMaskOffset64to79 | 1.3.6.1.4.1.171.12.9.1.3.1.6 | ||
| Specifies that the rule applies to the packet content(Offset64to79) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContMaskRowStatus | 1.3.6.1.4.1.171.12.9.1.3.1.7 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLPktContMaskOwner | 1.3.6.1.4.1.171.12.9.1.3.1.8 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLIpv6MaskTable | 1.3.6.1.4.1.171.12.9.1.4 | ||
| This table contain ACL mask of user-defined information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's ipv6 part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLIpv6MaskEntry | |||
| swACLIpv6MaskEntry | 1.3.6.1.4.1.171.12.9.1.4.1 | ||
| A list of information about ACL of user-defined. | |||
| OBJECT-TYPE | |||
| SwACLIpv6MaskEntry | |||
| swACLIpv6MaskProfileID | 1.3.6.1.4.1.171.12.9.1.4.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLIpv6MaskClass | 1.3.6.1.4.1.171.12.9.1.4.1.2 | ||
| Specifies that the rule applies to the IPv6 class field and the mask options. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swACLIpv6MaskFlowlabel | 1.3.6.1.4.1.171.12.9.1.4.1.3 | ||
| Specifies that the rule applies to the IPv6 flowlabel field and the mask options. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swACLIpv6IpAddrMaskState | 1.3.6.1.4.1.171.12.9.1.4.1.4 | ||
| This object indicates the status of IPv6 address mask. other(1) - Neither source IPv6 address nor destination IPv6 address are masked. dst-ipv6-addr(2) - recieved frames's destination IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. src-ipv6-addr(3) - recieved frames's source IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. dst-src-ipv6-addr(4) - recieved frames's destination IPv6 address or source IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-ipv6-addr(2), src-ipv6-addr(3), dst-src-ipv6-addr(4) | ||
| swACLIpv6MaskSrcIpv6Mask | 1.3.6.1.4.1.171.12.9.1.4.1.5 | ||
| Specifies that the rule applies to the Source IPv6 address and the mask options. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swACLIpv6MaskDstIpv6Mask | 1.3.6.1.4.1.171.12.9.1.4.1.6 | ||
| Specifies that the rule applies to the Destination IPv6 address and the mask options. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swACLIpv6MaskRowStatus | 1.3.6.1.4.1.171.12.9.1.4.1.7 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLIpv6MaskOwner | 1.3.6.1.4.1.171.12.9.1.4.1.8 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLMaskDelAllState | 1.3.6.1.4.1.171.12.9.1.5 | ||
| Used to delete all ACL mask. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), start(2) | ||
| swAclRuleMgmt | 1.3.6.1.4.1.171.12.9.2 | ||
| OBJECT IDENTIFIER | |||
| swACLEtherRuleTable | 1.3.6.1.4.1.171.12.9.2.1 | ||
| This table contain ACL rule of ethernet information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLEtherRuleEntry | |||
| swACLEtherRuleEntry | 1.3.6.1.4.1.171.12.9.2.1.1 | ||
| A list of information about ACL rule of the layer 2 part of each packet. | |||
| OBJECT-TYPE | |||
| SwACLEtherRuleEntry | |||
| swACLEtherRuleProfileID | 1.3.6.1.4.1.171.12.9.2.1.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLEtherRuleAccessID | 1.3.6.1.4.1.171.12.9.2.1.1.2 | ||
| The ID of ACL rule entry relate to swACLEtherRuleProfileID. while row creation Set to 0 to indicate assign Access ID automatically for the ports in the swACLEtherRulePort to create Rule entries for swACLEtherRulePort accordingly. Set to 1-65535 indicates to create the exact access ID for the swACLEtherRulePort and the swACLEtherRulePort must set one port only otherwise the row creation will be fail. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLEtherRuleVlan | 1.3.6.1.4.1.171.12.9.2.1.1.3 | ||
| Specifies that the access will apply to only to this VLAN. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(1..32) | ||
| swACLEtherRuleSrcMacAddress | 1.3.6.1.4.1.171.12.9.2.1.1.4 | ||
| Specifies that the access will apply to only packets with this source MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swACLEtherRuleDstMacAddress | 1.3.6.1.4.1.171.12.9.2.1.1.5 | ||
| Specifies that the access will apply to only packets with this destination MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swACLEtherRule8021P | 1.3.6.1.4.1.171.12.9.2.1.1.6 | ||
| Specifies that the access will apply only to packets with this 802.1p priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swACLEtherRuleEtherType | 1.3.6.1.4.1.171.12.9.2.1.1.7 | ||
| Specifies that the access will apply only to packets with this hexidecimal 802.1Q Ethernet type value in the packet header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swACLEtherRuleEnablePriority | 1.3.6.1.4.1.171.12.9.2.1.1.8 | ||
| Specifies that the access will apply only to packets with priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEtherRulePriority | 1.3.6.1.4.1.171.12.9.2.1.1.9 | ||
| Specific the priority will change to the packets while the swACLEtherRuleReplacePriority is enabled . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swACLEtherRuleReplacePriority | 1.3.6.1.4.1.171.12.9.2.1.1.10 | ||
| Specific the packets that match the access profile will changed the 802.1p priority tag field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEtherRuleEnableReplaceDscp | 1.3.6.1.4.1.171.12.9.2.1.1.11 | ||
| Specific the packets that match the access profile will replaced the DSCP field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLEtherRuleRepDscp | 1.3.6.1.4.1.171.12.9.2.1.1.12 | ||
| specify a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLEtherRulePermit | 1.3.6.1.4.1.171.12.9.2.1.1.13 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swACLEtherRulePort | 1.3.6.1.4.1.171.12.9.2.1.1.14 | ||
| Specifies that the access will apply to only to port(s). | |||
| OBJECT-TYPE | |||
| PortList | |||
| swACLEtherRuleRowStatus | 1.3.6.1.4.1.171.12.9.2.1.1.15 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLEtherRuleOwner | 1.3.6.1.4.1.171.12.9.2.1.1.16 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLIpRuleTable | 1.3.6.1.4.1.171.12.9.2.2 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLIpRuleEntry | |||
| swACLIpRuleEntry | 1.3.6.1.4.1.171.12.9.2.2.1 | ||
| OBJECT-TYPE | |||
| SwACLIpRuleEntry | |||
| swACLIpRuleProfileID | 1.3.6.1.4.1.171.12.9.2.2.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLIpRuleAccessID | 1.3.6.1.4.1.171.12.9.2.2.1.2 | ||
| The ID of ACL rule entry relate to swACLIPRuleProfileID. while row creation Set to 0 to indicate assign Access ID automatically for the ports in the swACLIpRulePort to create Rule entries for swACLIpRulePort accordingly. Set to 1-65535 indicates to create the exact access ID for the swACLIpRulePort and the swACLIpRulePort must set one port only otherwise the row creation will be fail. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLIpRuleVlan | 1.3.6.1.4.1.171.12.9.2.2.1.3 | ||
| Specifies that the access will apply to only to this VLAN. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(1..32) | ||
| swACLIpRuleSrcIpaddress | 1.3.6.1.4.1.171.12.9.2.2.1.4 | ||
| Specific an IP source address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swACLIpRuleDstIpaddress | 1.3.6.1.4.1.171.12.9.2.2.1.5 | ||
| Specific an IP destination address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swACLIpRuleDscp | 1.3.6.1.4.1.171.12.9.2.2.1.6 | ||
| Specific the value of dscp, the value can be configured 0 to 63 | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLIpRuleProtocol | 1.3.6.1.4.1.171.12.9.2.2.1.7 | ||
| Specifies the IP protocol which has been configured in swACLIpEntry . | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6) | ||
| swACLIpRuleType | 1.3.6.1.4.1.171.12.9.2.2.1.8 | ||
| Specific that the rule applies to the value of icmp type traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swACLIpRuleCode | 1.3.6.1.4.1.171.12.9.2.2.1.9 | ||
| Specific that the rule applies to the value of icmp code traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swACLIpRuleSrcPort | 1.3.6.1.4.1.171.12.9.2.2.1.10 | ||
| Specific that the rule applies the range of tcp/udp source port | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLIpRuleDstPort | 1.3.6.1.4.1.171.12.9.2.2.1.11 | ||
| Specific the range of tcp/udp destination port range | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLIpRuleFlagBits | 1.3.6.1.4.1.171.12.9.2.2.1.12 | ||
| A value which indicates the set of TCP flags that this entity may potentially offers. The value is a sum. This sum initially takes the value zero, Then, for each flag, L, in the range 1 through 6, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example,it you want to enable urg bit and ack bit,you should set vlaue 48(2^(5-1) + 2^(6-1)). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLIpRuleProtoID | 1.3.6.1.4.1.171.12.9.2.2.1.13 | ||
| Specific that the rule applies to the value of ip protocol id traffic | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swACLIpRuleUserMask | 1.3.6.1.4.1.171.12.9.2.2.1.14 | ||
| Specific that the rule applies to the ip protocol id and the range of options behind the IP header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(20) | ||
| swACLIpRuleEnablePriority | 1.3.6.1.4.1.171.12.9.2.2.1.15 | ||
| Specifies that the access will apply only to packets with priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpRulePriority | 1.3.6.1.4.1.171.12.9.2.2.1.16 | ||
| Specific the priority will change to the packets while the swACLIpRuleEnablePriority is enabled . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swACLIpRuleReplacePriority | 1.3.6.1.4.1.171.12.9.2.2.1.17 | ||
| Specific the packets that match the access profile will changed the 802.1p priority tag field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpRuleEnableReplaceDscp | 1.3.6.1.4.1.171.12.9.2.2.1.18 | ||
| Indicate weather the DSCP field can be over-write or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpRuleRepDscp | 1.3.6.1.4.1.171.12.9.2.2.1.19 | ||
| specify a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLIpRulePermit | 1.3.6.1.4.1.171.12.9.2.2.1.20 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swACLIpRulePort | 1.3.6.1.4.1.171.12.9.2.2.1.21 | ||
| Specifies that the access will apply to only to port(s). | |||
| OBJECT-TYPE | |||
| PortList | |||
| swACLIpRuleRowStatus | 1.3.6.1.4.1.171.12.9.2.2.1.22 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLIpRuleOwner | 1.3.6.1.4.1.171.12.9.2.2.1.23 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLPktContRuleTable | 1.3.6.1.4.1.171.12.9.2.3 | ||
| This table contain ACL rule of user-defined information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLPktContRuleEntry | |||
| swACLPktContRuleEntry | 1.3.6.1.4.1.171.12.9.2.3.1 | ||
| A list of information about ACL rule of the user-defined part of each packet. | |||
| OBJECT-TYPE | |||
| SwACLPktContRuleEntry | |||
| swACLPktContRuleProfileID | 1.3.6.1.4.1.171.12.9.2.3.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLPktContRuleAccessID | 1.3.6.1.4.1.171.12.9.2.3.1.2 | ||
| The ID of ACL rule entry relate to swACLPktContRuleProfileID. while row creation Set to 0 to indicate assign Access ID automatically for the ports in the swACLPktContRulePort to create Rule entries for swACLPktContRulePort accordingly. Set to 1-65535 indicates to create the exact access ID for the swACLPktContRulePort and the swACLPktContRulePort must set one port only otherwise the row creation will be fail. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLPktContRuleOffset0to15 | 1.3.6.1.4.1.171.12.9.2.3.1.3 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContRuleOffset16to31 | 1.3.6.1.4.1.171.12.9.2.3.1.4 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContRuleOffset32to47 | 1.3.6.1.4.1.171.12.9.2.3.1.5 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContRuleOffset48to63 | 1.3.6.1.4.1.171.12.9.2.3.1.6 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContRuleOffset64to79 | 1.3.6.1.4.1.171.12.9.2.3.1.7 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swACLPktContRuleEnablePriority | 1.3.6.1.4.1.171.12.9.2.3.1.8 | ||
| Specifies that the access will apply only to packets with priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLPktContRulePriority | 1.3.6.1.4.1.171.12.9.2.3.1.9 | ||
| Specific the priority will change to the packets while the swACLPktContRuleReplacePriority is enabled . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swACLPktContRuleReplacePriority | 1.3.6.1.4.1.171.12.9.2.3.1.10 | ||
| Specific the packets that match the access profile will changed the 802.1p priority tag field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLPktContRuleEnableReplaceDscp | 1.3.6.1.4.1.171.12.9.2.3.1.11 | ||
| Specific the packets that match the access profile will replaced the DSCP field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLPktContRuleRepDscp | 1.3.6.1.4.1.171.12.9.2.3.1.12 | ||
| specify a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will over-write the value in the DSCP field of the packet. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swACLPktContRulePermit | 1.3.6.1.4.1.171.12.9.2.3.1.13 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. lease-renew - Specifies the packets that match the access profile are copied to the CPU. Note : After user enables port's lease-renew state, all kinds of DHCP packets (include unicast and broadcast DHCP packets) will be copied to CPU (using user ACL mask and rule). | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2), lease-renew(3) | ||
| swACLPktContRulePort | 1.3.6.1.4.1.171.12.9.2.3.1.14 | ||
| Specifies that the access will apply to only to port(s). | |||
| OBJECT-TYPE | |||
| PortList | |||
| swACLPktContRuleRowStatus | 1.3.6.1.4.1.171.12.9.2.3.1.15 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLPktContRuleOwner | 1.3.6.1.4.1.171.12.9.2.3.1.16 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swACLIpv6RuleTable | 1.3.6.1.4.1.171.12.9.2.4 | ||
| This table contain ACL rule of user-defined information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwACLIpv6RuleEntry | |||
| swACLIpv6RuleEntry | 1.3.6.1.4.1.171.12.9.2.4.1 | ||
| A list of information about ACL rule of the user-defined part of each packet. | |||
| OBJECT-TYPE | |||
| SwACLIpv6RuleEntry | |||
| swACLIpv6RuleProfileID | 1.3.6.1.4.1.171.12.9.2.4.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swACLIpv6RuleAccessID | 1.3.6.1.4.1.171.12.9.2.4.1.2 | ||
| The ID of ACL rule entry relate to swACLIpv6RuleProfileID. while row creation Set to 0 to indicate assign Access ID automatically for the ports in the swACLIpv6RulePort to create Rule entries for swACLIpv6RulePort accordingly. Set to 1-65535 indicates to create the exact access ID for the swACLIpv6RulePort and the swACLIpv6RulePort must set one port only otherwise the row creation will be fail. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swACLIpv6RuleClass | 1.3.6.1.4.1.171.12.9.2.4.1.3 | ||
| Specifies that the rule applies to the IPv6 class filed. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swACLIpv6RuleFlowlabel | 1.3.6.1.4.1.171.12.9.2.4.1.4 | ||
| Specifies that the rule applies to the IPv6 flowlabel filed. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| swACLIpv6RuleSrcIpv6Addr | 1.3.6.1.4.1.171.12.9.2.4.1.5 | ||
| Specifies that the rule applies to the source IPv6 address. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swACLIpv6RuleDstIpv6Addr | 1.3.6.1.4.1.171.12.9.2.4.1.6 | ||
| Specifies that the rule applies to the destination IPv6 address. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swACLIpv6RuleEnablePriority | 1.3.6.1.4.1.171.12.9.2.4.1.7 | ||
| Specifies that the access will apply only to packets with priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpv6RulePriority | 1.3.6.1.4.1.171.12.9.2.4.1.8 | ||
| Specific the priority will change to the packets while the swACLIpv6RuleReplacePriority is enabled . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swACLIpv6RuleReplacePriority | 1.3.6.1.4.1.171.12.9.2.4.1.9 | ||
| Specific the packets that match the access profile will changed the 802.1p priority tag field by the switch or not . | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swACLIpv6RulePermit | 1.3.6.1.4.1.171.12.9.2.4.1.10 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swACLIpv6RulePort | 1.3.6.1.4.1.171.12.9.2.4.1.11 | ||
| Specifies that the access will apply to only to port(s). | |||
| OBJECT-TYPE | |||
| PortList | |||
| swACLIpv6RuleRowStatus | 1.3.6.1.4.1.171.12.9.2.4.1.12 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swACLIpv6RuleOwner | 1.3.6.1.4.1.171.12.9.2.4.1.13 | ||
| The owner of ACL mask entry. Only owner can be modify this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | any(0), acl(1), ipbind(2), other(4), dhcp(5), netbios(6), ext-netbios(7) | ||
| swAclCtrl | 1.3.6.1.4.1.171.12.9.3 | ||
| OBJECT IDENTIFIER | |||
| swCpuInterfacefilterState | 1.3.6.1.4.1.171.12.9.3.1 | ||
| enable/disable CPU Interface Filtering( also call Software ACL), default is disabled. If enable is configured, the filtering entries in the swAclRuleMgmt tables will be set to action if it's RuleSwAclState is enable.If disable is configured the software ACL function will be disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclMaskMgmt | 1.3.6.1.4.1.171.12.9.4 | ||
| OBJECT IDENTIFIER | |||
| swCpuAclEthernetTable | 1.3.6.1.4.1.171.12.9.4.1 | ||
| This table contain ACL mask of Ethernet information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's layer 2 part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclEthernetEntry | |||
| swCpuAclEthernetEntry | 1.3.6.1.4.1.171.12.9.4.1.1 | ||
| A list of information about ACL of Ethernet. | |||
| OBJECT-TYPE | |||
| SwCpuAclEthernetEntry | |||
| swCpuAclEthernetProfileID | 1.3.6.1.4.1.171.12.9.4.1.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclEthernetUsevlan | 1.3.6.1.4.1.171.12.9.4.1.1.2 | ||
| Specifies that the switch will examine the VLAN part of each packet header. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swCpuAclEthernetMacAddrMaskState | 1.3.6.1.4.1.171.12.9.4.1.1.3 | ||
| This object indicates the status of MAC address mask. other(1) - Neither source MAC address nor destination MAC address are masked. dst-mac-addr(2) - recieved frames's destination MAC address are currently used to be filtered as it meets with the MAC address entry of the table. src-mac-addr(3) - recieved frames's source MAC address are currently used to be filtered as it meets with the MAC address entry of the table. dst-src-mac-addr(4) - recieved frames's destination MAC address or source MAC address are currently used to be filtered as it meets with the MAC address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-mac-addr(2), src-mac-addr(3), dst-src-mac-addr(4) | ||
| swCpuAclEthernetSrcMacAddrMask | 1.3.6.1.4.1.171.12.9.4.1.1.4 | ||
| This object Specifies the MAC address mask for the source MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swCpuAclEthernetDstMacAddrMask | 1.3.6.1.4.1.171.12.9.4.1.1.5 | ||
| This object Specifies the MAC address mask for the destination MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swCpuAclEthernetUse8021p | 1.3.6.1.4.1.171.12.9.4.1.1.6 | ||
| Specifies if the switch will examine the 802.1p priority value in the frame's header or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swCpuAclEthernetUseEthernetType | 1.3.6.1.4.1.171.12.9.4.1.1.7 | ||
| Specifies if the switch will examine the Ethernet type value in each frame's header or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swCpuAclEthernetRowStatus | 1.3.6.1.4.1.171.12.9.4.1.1.8 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclIpTable | 1.3.6.1.4.1.171.12.9.4.2 | ||
| This table contain ACL mask of IP information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's IP layer part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclIpEntry | |||
| swCpuAclIpEntry | 1.3.6.1.4.1.171.12.9.4.2.1 | ||
| A list of information about ACL of IP Layer. | |||
| OBJECT-TYPE | |||
| SwCpuAclIpEntry | |||
| swCpuAclIpProfileID | 1.3.6.1.4.1.171.12.9.4.2.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclIpUsevlan | 1.3.6.1.4.1.171.12.9.4.2.1.2 | ||
| This object indicates if IP layer vlan is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swCpuAclIpIpAddrMaskState | 1.3.6.1.4.1.171.12.9.4.2.1.3 | ||
| This object indicates the status of IP address mask. other(1) - Neither source IP address nor destination IP address are masked. dst-ip-addr(2) - recieved frames's destination IP address are currently used to be filtered as it meets with the IP address entry of the table. src-ip-addr(3) - recieved frames's source IP address are currently used to be filtered as it meets with the IP address entry of the table. dst-src-ip-addr(4) - recieved frames's destination IP address or source IP address are currently used to be filtered as it meets with the IP address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-ip-addr(2), src-ip-addr(3), dst-src-ip-addr(4) | ||
| swCpuAclIpSrcIpAddrMask | 1.3.6.1.4.1.171.12.9.4.2.1.4 | ||
| This object Specifies IP address mask for the source IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swCpuAclIpDstIpAddrMask | 1.3.6.1.4.1.171.12.9.4.2.1.5 | ||
| This object Specifies the IP address mask for the destination IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swCpuAclIpUseDSCP | 1.3.6.1.4.1.171.12.9.4.2.1.6 | ||
| This object indicates DSCP protocol is is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swCpuAclIpUseProtoType | 1.3.6.1.4.1.171.12.9.4.2.1.7 | ||
| That object indicates which protocol will be examined. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6) | ||
| swCpuAclIpIcmpOption | 1.3.6.1.4.1.171.12.9.4.2.1.8 | ||
| This object indicates which fields should be filled in of ICMP. none(1)- two fields are null. type(2)- type field should be filled in. code(3)- code field should be filled in. type-code(4)- not only type fileld but code field should be filled in. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), type(2), code(3), type-code(4) | ||
| swCpuAclIpIgmpOption | 1.3.6.1.4.1.171.12.9.4.2.1.9 | ||
| This object indicates Options of IGMP is examined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclIpTcpOption | 1.3.6.1.4.1.171.12.9.4.2.1.10 | ||
| This object indicates the status of filtered address of TCP. other(1) - Neither source port nor destination port are masked. dst-addr(2) - recieved frames's destination port are currently used to be filtered . src-addr(3) - recieved frames's source port are currently used to be filtered . dst-src-addr(4) - both recieved frames's destination port and source port are currently used to be filtered . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4) | ||
| swCpuAclIpUdpOption | 1.3.6.1.4.1.171.12.9.4.2.1.11 | ||
| This object indicates the status of filtered address of UDP . other(1) - Neither source port nor destination port are masked. dst-addr(2) - recieved frames's destination port are currently used to be filtered . src-addr(3) - recieved frames's source port are currently used to be filtered . dst-src-addr(4) - recieved frames's destination port or source port are currently used to be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4) | ||
| swCpuAclIpTCPorUDPSrcPortMask | 1.3.6.1.4.1.171.12.9.4.2.1.12 | ||
| Specifies a TCP port mask for the source port if swCpuAclIpUseProtoType is TCP Specifies a UDP port mask for the source port if swCpuAclIpUseProtoType is UDP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swCpuAclIpTCPorUDPDstPortMask | 1.3.6.1.4.1.171.12.9.4.2.1.13 | ||
| Specifies a TCP port mask for the destination port if swCpuAclIpUseProtoType is TCP Specifies a UDP port mask for the destination port if swCpuAclIpUseProtoType is UDP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swCpuAclIpTCPFlagBit | 1.3.6.1.4.1.171.12.9.4.2.1.14 | ||
| Specifies a TCP connection flag mask. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclIpTCPFlagBitMask | 1.3.6.1.4.1.171.12.9.4.2.1.15 | ||
| A value which indicates the set of TCP flags that this entity may potentially offers. The value is a sum. This sum initially takes the value zero, Then, for each flag, L, in the range 1 through 6, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example,it you want to enable urg bit and ack bit,you should set vlaue 48(2^(5-1) + 2^(6-1)). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swCpuAclIpProtoIDOption | 1.3.6.1.4.1.171.12.9.4.2.1.16 | ||
| Specifies that the switch will examine each frame's Protocol ID field or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclIpProtoID | 1.3.6.1.4.1.171.12.9.4.2.1.17 | ||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swCpuAclIpProtoIDMask | 1.3.6.1.4.1.171.12.9.4.2.1.18 | ||
| Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(20) | ||
| swCpuAclIpRowStatus | 1.3.6.1.4.1.171.12.9.4.2.1.19 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclPktContMaskTable | 1.3.6.1.4.1.171.12.9.4.3 | ||
| This table contain ACL mask of user-defined information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's user-defined part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclPktContMaskEntry | |||
| swCpuAclPktContMaskEntry | 1.3.6.1.4.1.171.12.9.4.3.1 | ||
| A list of information about ACL of user-defined. | |||
| OBJECT-TYPE | |||
| SwCpuAclPktContMaskEntry | |||
| swCpuAclPktContMaskProfileID | 1.3.6.1.4.1.171.12.9.4.3.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclPktContMaskOffset0to15 | 1.3.6.1.4.1.171.12.9.4.3.1.2 | ||
| Specifies that the rule applies to the packet content(Offset0to15) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContMaskOffset16to31 | 1.3.6.1.4.1.171.12.9.4.3.1.3 | ||
| Specifies that the rule applies to the packet content(Offset16to31) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContMaskOffset32to47 | 1.3.6.1.4.1.171.12.9.4.3.1.4 | ||
| Specifies that the rule applies to the packet content(Offset32to47) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContMaskOffset48to63 | 1.3.6.1.4.1.171.12.9.4.3.1.5 | ||
| Specifies that the rule applies to the packet content(Offset48to63) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContMaskOffset64to79 | 1.3.6.1.4.1.171.12.9.4.3.1.6 | ||
| Specifies that the rule applies to the packet content(Offset64to79) and the mask options. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContMaskRowStatus | 1.3.6.1.4.1.171.12.9.4.3.1.7 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclIpv6MaskTable | 1.3.6.1.4.1.171.12.9.4.4 | ||
| This table contain ACL mask of user-defined information. Access profiles will be created on the switch by row creation and to define which parts of each incoming frame's ipv6 part of header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclIpv6MaskEntry | |||
| swCpuAclIpv6MaskEntry | 1.3.6.1.4.1.171.12.9.4.4.1 | ||
| A list of information about ACL of user-defined. | |||
| OBJECT-TYPE | |||
| SwCpuAclIpv6MaskEntry | |||
| swCpuAclIpv6MaskProfileID | 1.3.6.1.4.1.171.12.9.4.4.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclIpv6MaskClass | 1.3.6.1.4.1.171.12.9.4.4.1.2 | ||
| Specifies that the rule applies to the IPv6 class field and the mask options. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclIpv6MaskFlowlabel | 1.3.6.1.4.1.171.12.9.4.4.1.3 | ||
| Specifies that the rule applies to the IPv6 flowlabel field and the mask options. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| swCpuAclIpv6IpAddrMaskState | 1.3.6.1.4.1.171.12.9.4.4.1.4 | ||
| This object indicates the status of IPv6 address mask. other(1) - Neither source IPv6 address nor destination IPv6 address are masked. dst-ipv6-addr(2) - recieved frames's destination IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. src-ipv6-addr(3) - recieved frames's source IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. dst-src-ipv6-addr(4) - recieved frames's destination IPv6 address or source IPv6 address are currently used to be filtered as it meets with the IPv6 address entry of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-ipv6-addr(2), src-ipv6-addr(3), dst-src-ipv6-addr(4) | ||
| swCpuAclIpv6MaskSrcIpv6Mask | 1.3.6.1.4.1.171.12.9.4.4.1.5 | ||
| Specifies that the rule applies to the Source IPv6 address and the mask options. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swCpuAclIpv6MaskDstIpv6Mask | 1.3.6.1.4.1.171.12.9.4.4.1.6 | ||
| Specifies that the rule applies to the Destination IPv6 address and the mask options. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swCpuAclIpv6MaskRowStatus | 1.3.6.1.4.1.171.12.9.4.4.1.7 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclRuleMgmt | 1.3.6.1.4.1.171.12.9.5 | ||
| OBJECT IDENTIFIER | |||
| swCpuAclEtherRuleTable | 1.3.6.1.4.1.171.12.9.5.1 | ||
| This table contain ACL rule of ethernet information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclEtherRuleEntry | |||
| swCpuAclEtherRuleEntry | 1.3.6.1.4.1.171.12.9.5.1.1 | ||
| A list of information about ACL rule of the layer 2 part of each packet. | |||
| OBJECT-TYPE | |||
| SwCpuAclEtherRuleEntry | |||
| swCpuAclEtherRuleProfileID | 1.3.6.1.4.1.171.12.9.5.1.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclEtherRuleAccessID | 1.3.6.1.4.1.171.12.9.5.1.1.2 | ||
| The ID of ACL rule entry relate to swCpuAclEtherRuleProfileID. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| swCpuAclEtherRuleVlan | 1.3.6.1.4.1.171.12.9.5.1.1.3 | ||
| Specifies that the access will apply to only to this VLAN. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(1..32) | ||
| swCpuAclEtherRuleSrcMacAddress | 1.3.6.1.4.1.171.12.9.5.1.1.4 | ||
| Specifies that the access will apply to only packets with this source MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swCpuAclEtherRuleDstMacAddress | 1.3.6.1.4.1.171.12.9.5.1.1.5 | ||
| Specifies that the access will apply to only packets with this destination MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swCpuAclEtherRule8021P | 1.3.6.1.4.1.171.12.9.5.1.1.6 | ||
| Specifies that the access will apply only to packets with this 802.1p priority value. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..7 | ||
| swCpuAclEtherRuleEtherType | 1.3.6.1.4.1.171.12.9.5.1.1.7 | ||
| Specifies that the access will apply only to packets with this hexidecimal 802.1Q Ethernet type value in the packet header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| swCpuAclEtherRulePermit | 1.3.6.1.4.1.171.12.9.5.1.1.8 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swCpuAclEtherRuleRowStatus | 1.3.6.1.4.1.171.12.9.5.1.1.9 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclIpRuleTable | 1.3.6.1.4.1.171.12.9.5.2 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclIpRuleEntry | |||
| swCpuAclIpRuleEntry | 1.3.6.1.4.1.171.12.9.5.2.1 | ||
| OBJECT-TYPE | |||
| SwCpuAclIpRuleEntry | |||
| swCpuAclIpRuleProfileID | 1.3.6.1.4.1.171.12.9.5.2.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclIpRuleAccessID | 1.3.6.1.4.1.171.12.9.5.2.1.2 | ||
| The ID of CpuAcl IP rule entry . | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| swCpuAclIpRuleVlan | 1.3.6.1.4.1.171.12.9.5.2.1.3 | ||
| Specifies that the access will apply to only to this VLAN. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(1..32) | ||
| swCpuAclIpRuleSrcIpaddress | 1.3.6.1.4.1.171.12.9.5.2.1.4 | ||
| Specific an IP source address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swCpuAclIpRuleDstIpaddress | 1.3.6.1.4.1.171.12.9.5.2.1.5 | ||
| Specific an IP destination address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swCpuAclIpRuleDscp | 1.3.6.1.4.1.171.12.9.5.2.1.6 | ||
| Specific the value of dscp, the value can be configured 0 to 63 | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swCpuAclIpRuleProtocol | 1.3.6.1.4.1.171.12.9.5.2.1.7 | ||
| Specifies the IP protocol which has been configured in swCpuAclIpEntry . | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), icmp(2), igmp(3), tcp(4), udp(5), protocolId(6) | ||
| swCpuAclIpRuleType | 1.3.6.1.4.1.171.12.9.5.2.1.8 | ||
| Specific that the rule applies to the value of icmp type traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swCpuAclIpRuleCode | 1.3.6.1.4.1.171.12.9.5.2.1.9 | ||
| Specific that the rule applies to the value of icmp code traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swCpuAclIpRuleSrcPort | 1.3.6.1.4.1.171.12.9.5.2.1.10 | ||
| Specific that the rule applies the range of tcp/udp source port | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swCpuAclIpRuleDstPort | 1.3.6.1.4.1.171.12.9.5.2.1.11 | ||
| Specific the range of tcp/udp destination port range | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| swCpuAclIpRuleFlagBits | 1.3.6.1.4.1.171.12.9.5.2.1.12 | ||
| A value which indicates the set of TCP flags that this entity may potentially offers. The value is a sum. This sum initially takes the value zero, Then, for each flag, L, in the range 1 through 6, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. Note that values should be calculated accordingly: Flag functionality 6 urg bit 5 ack bit 4 psh bit 3 rst bit 2 syn bit 1 fin bit For example,it you want to enable urg bit and ack bit,you should set vlaue 48(2^(5-1) + 2^(6-1)). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..63 | ||
| swCpuAclIpRuleProtoID | 1.3.6.1.4.1.171.12.9.5.2.1.13 | ||
| Specific that the rule applies to the value of ip protocol id traffic | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swCpuAclIpRuleUserMask | 1.3.6.1.4.1.171.12.9.5.2.1.14 | ||
| Specific that the rule applies to the ip protocol id and the range of options behind the IP header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(20) | ||
| swCpuAclIpRulePermit | 1.3.6.1.4.1.171.12.9.5.2.1.15 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swCpuAclIpRuleRowStatus | 1.3.6.1.4.1.171.12.9.5.2.1.16 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclPktContRuleTable | 1.3.6.1.4.1.171.12.9.5.3 | ||
| This table contain ACL rule of user-defined information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclPktContRuleEntry | |||
| swCpuAclPktContRuleEntry | 1.3.6.1.4.1.171.12.9.5.3.1 | ||
| A list of information about ACL rule of the user-defined part of each packet. | |||
| OBJECT-TYPE | |||
| SwCpuAclPktContRuleEntry | |||
| swCpuAclPktContRuleProfileID | 1.3.6.1.4.1.171.12.9.5.3.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclPktContRuleAccessID | 1.3.6.1.4.1.171.12.9.5.3.1.2 | ||
| The ID of ACL rule entry relate to swCpuAclPktContRuleProfileID. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| swCpuAclPktContRuleOffset0to15 | 1.3.6.1.4.1.171.12.9.5.3.1.3 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContRuleOffset16to31 | 1.3.6.1.4.1.171.12.9.5.3.1.4 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContRuleOffset32to47 | 1.3.6.1.4.1.171.12.9.5.3.1.5 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContRuleOffset48to63 | 1.3.6.1.4.1.171.12.9.5.3.1.6 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContRuleOffset64to79 | 1.3.6.1.4.1.171.12.9.5.3.1.7 | ||
| Specifies that the rule applies to the user-defined packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swCpuAclPktContRulePermit | 1.3.6.1.4.1.171.12.9.5.3.1.8 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swCpuAclPktContRuleRowStatus | 1.3.6.1.4.1.171.12.9.5.3.1.9 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swCpuAclIpv6RuleTable | 1.3.6.1.4.1.171.12.9.5.4 | ||
| This table contain ACL rule of user-defined information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwCpuAclIpv6RuleEntry | |||
| swCpuAclIpv6RuleEntry | 1.3.6.1.4.1.171.12.9.5.4.1 | ||
| A list of information about ACL rule of the user-defined part of each packet. | |||
| OBJECT-TYPE | |||
| SwCpuAclIpv6RuleEntry | |||
| swCpuAclIpv6RuleProfileID | 1.3.6.1.4.1.171.12.9.5.4.1.1 | ||
| The ID of ACL mask entry ,and is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| swCpuAclIpv6RuleAccessID | 1.3.6.1.4.1.171.12.9.5.4.1.2 | ||
| The ID of ACL rule entry relate to swCpuAclIpv6RuleProfileID. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| swCpuAclIpv6RuleClass | 1.3.6.1.4.1.171.12.9.5.4.1.3 | ||
| Specifies that the rule applies to the IPv6 class filed. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| swCpuAclIpv6RuleFlowlabel | 1.3.6.1.4.1.171.12.9.5.4.1.4 | ||
| Specifies that the rule applies to the IPv6 flowlabel filed. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| swCpuAclIpv6RuleSrcIpv6Addr | 1.3.6.1.4.1.171.12.9.5.4.1.5 | ||
| Specifies that the rule applies to the source IPv6 address. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swCpuAclIpv6RuleDstIpv6Addr | 1.3.6.1.4.1.171.12.9.5.4.1.6 | ||
| Specifies that the rule applies to the destination IPv6 address. This should be 16 byte octet string. | |||
| OBJECT-TYPE | |||
| Ipv6Address | |||
| swCpuAclIpv6RulePermit | 1.3.6.1.4.1.171.12.9.5.4.1.7 | ||
| This object indicates resoult of examination is permit or deny;default is permit(1) permit - Specifies that packets that match the access profile are permitted to be forwarded by the switch. deny - Specifies that packets that do not match the access profile are not permitted to be forwarded by the switch and will be filtered. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(1), permit(2) | ||
| swCpuAclIpv6RuleRowStatus | 1.3.6.1.4.1.171.12.9.5.4.1.8 | ||
| This object indicates the status of this entry. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| swAclMeteringMgmt | 1.3.6.1.4.1.171.12.9.6 | ||
| OBJECT IDENTIFIER | |||
| swAclMeterTable | 1.3.6.1.4.1.171.12.9.6.1 | ||
| This table is used to configure the flow-based metering function. The access rule must first be created before the parameters of this function can be applied. Users may set the preferred bandwidth for this rule, in Kbps ;Once the bandwidth has been exceeded, overflow packets will be either dropped or set for a drop precedence, depending on user configuration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwAclMeterEntry | |||
| swAclMeterEntry | 1.3.6.1.4.1.171.12.9.6.1.1 | ||
| This entry displays parameters and configurations set for the flow metering function. | |||
| OBJECT-TYPE | |||
| SwAclMeterEntry | |||
| swAclMeterProfileID | 1.3.6.1.4.1.171.12.9.6.1.1.1 | ||
| The ID of the ACL mask entry is unique in the mask list. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swAclMeterAccessID | 1.3.6.1.4.1.171.12.9.6.1.1.2 | ||
| The ID of the ACL rule entry as related to the swAclMeterProfileID. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| swAclMeterRate | 1.3.6.1.4.1.171.12.9.6.1.1.3 | ||
| Specify the committed bandwidth in Kbps for the flow. NOTE: 1.Specifying 0 will disable this flow meter setting. 2.Users must set the swAclMeterActionForRateExceed object to activate this entry. 3.The bandwidth is not a multiple of 64, closest value is choosed. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..999936 | ||
| swAclMeterActionForRateExceed | 1.3.6.1.4.1.171.12.9.6.1.1.4 | ||
| Specifies the action to take for those packets exceeding the committed rate. NOTE: Users must also set the swAclMeterRate to activate this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), drop-packet(2), set-drop-precedence(3) | ||
| swAclMeteringNumOfEntryInUse | 1.3.6.1.4.1.171.12.9.6.2 | ||
| Used to display total entries of the flow metering. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| PortList | |||
| OCTET STRING | SIZE(0..127) | ||
| Ipv6Address | |||
| This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(16) | ||
| SwACLEthernetEntry | |||
| SEQUENCE | |||
| INTEGER as swACLEthernetProfileID | |||
| INTEGER as swACLEthernetUsevlan | |||
| INTEGER as swACLEthernetMacAddrMaskState | |||
| MacAddress as swACLEthernetSrcMacAddrMask | |||
| MacAddress as swACLEthernetDstMacAddrMask | |||
| INTEGER as swACLEthernetUse8021p | |||
| INTEGER as swACLEthernetUseEthernetType | |||
| RowStatus as swACLEthernetRowStatus | |||
| INTEGER as swACLEthernetOwner | |||
| SwACLIpEntry | |||
| SEQUENCE | |||
| INTEGER as swACLIpProfileID | |||
| INTEGER as swACLIpUsevlan | |||
| INTEGER as swACLIpIpAddrMaskState | |||
| IpAddress as swACLIpSrcIpAddrMask | |||
| IpAddress as swACLIpDstIpAddrMask | |||
| INTEGER as swACLIpUseDSCP | |||
| INTEGER as swACLIpUseProtoType | |||
| INTEGER as swACLIpIcmpOption | |||
| INTEGER as swACLIpIgmpOption | |||
| INTEGER as swACLIpTcpOption | |||
| INTEGER as swACLIpUdpOption | |||
| OCTET STRING as swACLIpTCPorUDPSrcPortMask | |||
| OCTET STRING as swACLIpTCPorUDPDstPortMask | |||
| INTEGER as swACLIpTCPFlagBit | |||
| INTEGER as swACLIpTCPFlagBitMask | |||
| INTEGER as swACLIpProtoIDOption | |||
| INTEGER as swACLIpProtoID | |||
| OCTET STRING as swACLIpProtoIDMask | |||
| RowStatus as swACLIpRowStatus | |||
| INTEGER as swACLIpOwner | |||
| SwACLPktContMaskEntry | |||
| SEQUENCE | |||
| INTEGER as swACLPktContMaskProfileID | |||
| OCTET STRING as swACLPktContMaskOffset0to15 | |||
| OCTET STRING as swACLPktContMaskOffset16to31 | |||
| OCTET STRING as swACLPktContMaskOffset32to47 | |||
| OCTET STRING as swACLPktContMaskOffset48to63 | |||
| OCTET STRING as swACLPktContMaskOffset64to79 | |||
| RowStatus as swACLPktContMaskRowStatus | |||
| INTEGER as swACLPktContMaskOwner | |||
| SwACLIpv6MaskEntry | |||
| SEQUENCE | |||
| INTEGER as swACLIpv6MaskProfileID | |||
| INTEGER as swACLIpv6MaskClass | |||
| INTEGER as swACLIpv6MaskFlowlabel | |||
| INTEGER as swACLIpv6IpAddrMaskState | |||
| Ipv6Address as swACLIpv6MaskSrcIpv6Mask | |||
| Ipv6Address as swACLIpv6MaskDstIpv6Mask | |||
| RowStatus as swACLIpv6MaskRowStatus | |||
| INTEGER as swACLIpv6MaskOwner | |||
| SwACLEtherRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swACLEtherRuleProfileID | |||
| INTEGER as swACLEtherRuleAccessID | |||
| SnmpAdminString as swACLEtherRuleVlan | |||
| MacAddress as swACLEtherRuleSrcMacAddress | |||
| MacAddress as swACLEtherRuleDstMacAddress | |||
| INTEGER as swACLEtherRule8021P | |||
| OCTET STRING as swACLEtherRuleEtherType | |||
| INTEGER as swACLEtherRuleEnablePriority | |||
| INTEGER as swACLEtherRulePriority | |||
| INTEGER as swACLEtherRuleReplacePriority | |||
| INTEGER as swACLEtherRuleEnableReplaceDscp | |||
| INTEGER as swACLEtherRuleRepDscp | |||
| INTEGER as swACLEtherRulePermit | |||
| PortList as swACLEtherRulePort | |||
| RowStatus as swACLEtherRuleRowStatus | |||
| INTEGER as swACLEtherRuleOwner | |||
| SwACLIpRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swACLIpRuleProfileID | |||
| INTEGER as swACLIpRuleAccessID | |||
| SnmpAdminString as swACLIpRuleVlan | |||
| IpAddress as swACLIpRuleSrcIpaddress | |||
| IpAddress as swACLIpRuleDstIpaddress | |||
| INTEGER as swACLIpRuleDscp | |||
| INTEGER as swACLIpRuleProtocol | |||
| INTEGER as swACLIpRuleType | |||
| INTEGER as swACLIpRuleCode | |||
| INTEGER as swACLIpRuleSrcPort | |||
| INTEGER as swACLIpRuleDstPort | |||
| INTEGER as swACLIpRuleFlagBits | |||
| INTEGER as swACLIpRuleProtoID | |||
| OCTET STRING as swACLIpRuleUserMask | |||
| INTEGER as swACLIpRuleEnablePriority | |||
| INTEGER as swACLIpRulePriority | |||
| INTEGER as swACLIpRuleReplacePriority | |||
| INTEGER as swACLIpRuleEnableReplaceDscp | |||
| INTEGER as swACLIpRuleRepDscp | |||
| INTEGER as swACLIpRulePermit | |||
| PortList as swACLIpRulePort | |||
| RowStatus as swACLIpRuleRowStatus | |||
| INTEGER as swACLIpRuleOwner | |||
| SwACLPktContRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swACLPktContRuleProfileID | |||
| INTEGER as swACLPktContRuleAccessID | |||
| OCTET STRING as swACLPktContRuleOffset0to15 | |||
| OCTET STRING as swACLPktContRuleOffset16to31 | |||
| OCTET STRING as swACLPktContRuleOffset32to47 | |||
| OCTET STRING as swACLPktContRuleOffset48to63 | |||
| OCTET STRING as swACLPktContRuleOffset64to79 | |||
| INTEGER as swACLPktContRuleEnablePriority | |||
| INTEGER as swACLPktContRulePriority | |||
| INTEGER as swACLPktContRuleReplacePriority | |||
| INTEGER as swACLPktContRuleEnableReplaceDscp | |||
| INTEGER as swACLPktContRuleRepDscp | |||
| INTEGER as swACLPktContRulePermit | |||
| PortList as swACLPktContRulePort | |||
| RowStatus as swACLPktContRuleRowStatus | |||
| INTEGER as swACLPktContRuleOwner | |||
| SwACLIpv6RuleEntry | |||
| SEQUENCE | |||
| INTEGER as swACLIpv6RuleProfileID | |||
| INTEGER as swACLIpv6RuleAccessID | |||
| INTEGER as swACLIpv6RuleClass | |||
| OCTET STRING as swACLIpv6RuleFlowlabel | |||
| Ipv6Address as swACLIpv6RuleSrcIpv6Addr | |||
| Ipv6Address as swACLIpv6RuleDstIpv6Addr | |||
| INTEGER as swACLIpv6RuleEnablePriority | |||
| INTEGER as swACLIpv6RulePriority | |||
| INTEGER as swACLIpv6RuleReplacePriority | |||
| INTEGER as swACLIpv6RulePermit | |||
| PortList as swACLIpv6RulePort | |||
| RowStatus as swACLIpv6RuleRowStatus | |||
| INTEGER as swACLIpv6RuleOwner | |||
| SwCpuAclEthernetEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclEthernetProfileID | |||
| INTEGER as swCpuAclEthernetUsevlan | |||
| INTEGER as swCpuAclEthernetMacAddrMaskState | |||
| MacAddress as swCpuAclEthernetSrcMacAddrMask | |||
| MacAddress as swCpuAclEthernetDstMacAddrMask | |||
| INTEGER as swCpuAclEthernetUse8021p | |||
| INTEGER as swCpuAclEthernetUseEthernetType | |||
| RowStatus as swCpuAclEthernetRowStatus | |||
| SwCpuAclIpEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclIpProfileID | |||
| INTEGER as swCpuAclIpUsevlan | |||
| INTEGER as swCpuAclIpIpAddrMaskState | |||
| IpAddress as swCpuAclIpSrcIpAddrMask | |||
| IpAddress as swCpuAclIpDstIpAddrMask | |||
| INTEGER as swCpuAclIpUseDSCP | |||
| INTEGER as swCpuAclIpUseProtoType | |||
| INTEGER as swCpuAclIpIcmpOption | |||
| INTEGER as swCpuAclIpIgmpOption | |||
| INTEGER as swCpuAclIpTcpOption | |||
| INTEGER as swCpuAclIpUdpOption | |||
| OCTET STRING as swCpuAclIpTCPorUDPSrcPortMask | |||
| OCTET STRING as swCpuAclIpTCPorUDPDstPortMask | |||
| INTEGER as swCpuAclIpTCPFlagBit | |||
| INTEGER as swCpuAclIpTCPFlagBitMask | |||
| INTEGER as swCpuAclIpProtoIDOption | |||
| INTEGER as swCpuAclIpProtoID | |||
| OCTET STRING as swCpuAclIpProtoIDMask | |||
| RowStatus as swCpuAclIpRowStatus | |||
| SwCpuAclPktContMaskEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclPktContMaskProfileID | |||
| OCTET STRING as swCpuAclPktContMaskOffset0to15 | |||
| OCTET STRING as swCpuAclPktContMaskOffset16to31 | |||
| OCTET STRING as swCpuAclPktContMaskOffset32to47 | |||
| OCTET STRING as swCpuAclPktContMaskOffset48to63 | |||
| OCTET STRING as swCpuAclPktContMaskOffset64to79 | |||
| RowStatus as swCpuAclPktContMaskRowStatus | |||
| SwCpuAclIpv6MaskEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclIpv6MaskProfileID | |||
| INTEGER as swCpuAclIpv6MaskClass | |||
| INTEGER as swCpuAclIpv6MaskFlowlabel | |||
| INTEGER as swCpuAclIpv6IpAddrMaskState | |||
| Ipv6Address as swCpuAclIpv6MaskSrcIpv6Mask | |||
| Ipv6Address as swCpuAclIpv6MaskDstIpv6Mask | |||
| RowStatus as swCpuAclIpv6MaskRowStatus | |||
| SwCpuAclEtherRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclEtherRuleProfileID | |||
| INTEGER as swCpuAclEtherRuleAccessID | |||
| SnmpAdminString as swCpuAclEtherRuleVlan | |||
| MacAddress as swCpuAclEtherRuleSrcMacAddress | |||
| MacAddress as swCpuAclEtherRuleDstMacAddress | |||
| INTEGER as swCpuAclEtherRule8021P | |||
| OCTET STRING as swCpuAclEtherRuleEtherType | |||
| INTEGER as swCpuAclEtherRulePermit | |||
| RowStatus as swCpuAclEtherRuleRowStatus | |||
| SwCpuAclIpRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclIpRuleProfileID | |||
| INTEGER as swCpuAclIpRuleAccessID | |||
| SnmpAdminString as swCpuAclIpRuleVlan | |||
| IpAddress as swCpuAclIpRuleSrcIpaddress | |||
| IpAddress as swCpuAclIpRuleDstIpaddress | |||
| INTEGER as swCpuAclIpRuleDscp | |||
| INTEGER as swCpuAclIpRuleProtocol | |||
| INTEGER as swCpuAclIpRuleType | |||
| INTEGER as swCpuAclIpRuleCode | |||
| INTEGER as swCpuAclIpRuleSrcPort | |||
| INTEGER as swCpuAclIpRuleDstPort | |||
| INTEGER as swCpuAclIpRuleFlagBits | |||
| INTEGER as swCpuAclIpRuleProtoID | |||
| OCTET STRING as swCpuAclIpRuleUserMask | |||
| INTEGER as swCpuAclIpRulePermit | |||
| RowStatus as swCpuAclIpRuleRowStatus | |||
| SwCpuAclPktContRuleEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclPktContRuleProfileID | |||
| INTEGER as swCpuAclPktContRuleAccessID | |||
| OCTET STRING as swCpuAclPktContRuleOffset0to15 | |||
| OCTET STRING as swCpuAclPktContRuleOffset16to31 | |||
| OCTET STRING as swCpuAclPktContRuleOffset32to47 | |||
| OCTET STRING as swCpuAclPktContRuleOffset48to63 | |||
| OCTET STRING as swCpuAclPktContRuleOffset64to79 | |||
| INTEGER as swCpuAclPktContRulePermit | |||
| RowStatus as swCpuAclPktContRuleRowStatus | |||
| SwCpuAclIpv6RuleEntry | |||
| SEQUENCE | |||
| INTEGER as swCpuAclIpv6RuleProfileID | |||
| INTEGER as swCpuAclIpv6RuleAccessID | |||
| INTEGER as swCpuAclIpv6RuleClass | |||
| OCTET STRING as swCpuAclIpv6RuleFlowlabel | |||
| Ipv6Address as swCpuAclIpv6RuleSrcIpv6Addr | |||
| Ipv6Address as swCpuAclIpv6RuleDstIpv6Addr | |||
| INTEGER as swCpuAclIpv6RulePermit | |||
| RowStatus as swCpuAclIpv6RuleRowStatus | |||
| SwAclMeterEntry | |||
| SEQUENCE | |||
| INTEGER as swAclMeterProfileID | |||
| INTEGER as swAclMeterAccessID | |||
| INTEGER as swAclMeterRate | |||
| INTEGER as swAclMeterActionForRateExceed | |||