ADSL-LINE-MIB

File: ADSL-LINE-MIB.mib (188155 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB PerfHist-TC-MIB SNMP-FRAMEWORK-MIB
ADSL-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 NOTIFICATION-TYPE transmission
Unsigned32 RowStatus TruthValue
VariablePointer MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP ifIndex PerfCurrentCount
PerfIntervalCount SnmpAdminString AdslPerfCurrDayCount
AdslPerfPrevDayCount AdslPerfTimeElapsed AdslLineCodingType

Defined Objects

adslMIB 1.3.6.1.2.1.10.94
The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such line has an entry in an ifTable which may include multiple modem lines. An agent may reside at either end of the ADSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level ADSL line protocol. The agent may monitor and control this protocol for its needs. ADSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus an ADSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to adsl(94), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs-- interval of Seconds in which xxx occurs (e.g., xxx=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks-- Blocks, a data unit, see adslAtuXChanCrcBlockLength
MODULE-IDENTITY    

adslLineMib 1.3.6.1.2.1.10.94.1
OBJECT IDENTIFIER    

adslMibObjects 1.3.6.1.2.1.10.94.1.1
OBJECT IDENTIFIER    

adslLineTable 1.3.6.1.2.1.10.94.1.1.1
This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineEntry

adslLineEntry 1.3.6.1.2.1.10.94.1.1.1.1
An entry in adslLineTable.
OBJECT-TYPE    
  AdslLineEntry  

adslLineCoding 1.3.6.1.2.1.10.94.1.1.1.1.1
Specifies the ADSL coding type used on this line.
OBJECT-TYPE    
  AdslLineCodingType  

adslLineType 1.3.6.1.2.1.10.94.1.1.1.1.2
Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s).
OBJECT-TYPE    
  INTEGER noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5)  

adslLineSpecific 1.3.6.1.2.1.10.94.1.1.1.1.3
OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM.
OBJECT-TYPE    
  VariablePointer  

adslLineConfProfile 1.3.6.1.2.1.10.94.1.1.1.1.4
The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the configuration profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..32)  

adslLineAlarmConfProfile 1.3.6.1.2.1.10.94.1.1.1.1.5
The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the alarm profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..32)  

adslAtucPhysTable 1.3.6.1.2.1.10.94.1.1.2
This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucPhysEntry

adslAtucPhysEntry 1.3.6.1.2.1.10.94.1.1.2.1
An entry in the adslAtucPhysTable.
OBJECT-TYPE    
  AdslAtucPhysEntry  

adslAtucInvSerialNumber 1.3.6.1.2.1.10.94.1.1.2.1.1
The vendor specific string that identifies the vendor equipment.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

adslAtucInvVendorID 1.3.6.1.2.1.10.94.1.1.2.1.2
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..16)  

adslAtucInvVersionNumber 1.3.6.1.2.1.10.94.1.1.2.1.3
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..16)  

adslAtucCurrSnrMgn 1.3.6.1.2.1.10.94.1.1.2.1.4
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
OBJECT-TYPE    
  INTEGER -640..640  

adslAtucCurrAtn 1.3.6.1.2.1.10.94.1.1.2.1.5
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
OBJECT-TYPE    
  Gauge32 0..630  

adslAtucCurrStatus 1.3.6.1.2.1.10.94.1.1.2.1.6
Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus.
OBJECT-TYPE    
  BITS noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9)  

adslAtucCurrOutputPwr 1.3.6.1.2.1.10.94.1.1.2.1.7
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
OBJECT-TYPE    
  INTEGER -310..310  

adslAtucCurrAttainableRate 1.3.6.1.2.1.10.94.1.1.2.1.8
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
OBJECT-TYPE    
  Gauge32  

adslAturPhysTable 1.3.6.1.2.1.10.94.1.1.3
This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturPhysEntry

adslAturPhysEntry 1.3.6.1.2.1.10.94.1.1.3.1
An entry in the adslAturPhysTable.
OBJECT-TYPE    
  AdslAturPhysEntry  

adslAturInvSerialNumber 1.3.6.1.2.1.10.94.1.1.3.1.1
The vendor specific string that identifies the vendor equipment.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

adslAturInvVendorID 1.3.6.1.2.1.10.94.1.1.3.1.2
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..16)  

adslAturInvVersionNumber 1.3.6.1.2.1.10.94.1.1.3.1.3
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..16)  

adslAturCurrSnrMgn 1.3.6.1.2.1.10.94.1.1.3.1.4
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
OBJECT-TYPE    
  INTEGER -640..640  

adslAturCurrAtn 1.3.6.1.2.1.10.94.1.1.3.1.5
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
OBJECT-TYPE    
  Gauge32 0..630  

adslAturCurrStatus 1.3.6.1.2.1.10.94.1.1.3.1.6
Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus.
OBJECT-TYPE    
  BITS noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4)  

adslAturCurrOutputPwr 1.3.6.1.2.1.10.94.1.1.3.1.7
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
OBJECT-TYPE    
  INTEGER -310..310  

adslAturCurrAttainableRate 1.3.6.1.2.1.10.94.1.1.3.1.8
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
OBJECT-TYPE    
  Gauge32  

adslAtucChanTable 1.3.6.1.2.1.10.94.1.1.4
This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucChanEntry

adslAtucChanEntry 1.3.6.1.2.1.10.94.1.1.4.1
An entry in the adslAtucChanTable.
OBJECT-TYPE    
  AdslAtucChanEntry  

adslAtucChanInterleaveDelay 1.3.6.1.2.1.10.94.1.1.4.1.1
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.
OBJECT-TYPE    
  Gauge32  

adslAtucChanCurrTxRate 1.3.6.1.2.1.10.94.1.1.4.1.2
Actual transmit rate on this channel.
OBJECT-TYPE    
  Gauge32  

adslAtucChanPrevTxRate 1.3.6.1.2.1.10.94.1.1.4.1.3
The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.
OBJECT-TYPE    
  Gauge32  

adslAtucChanCrcBlockLength 1.3.6.1.2.1.10.94.1.1.4.1.4
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
OBJECT-TYPE    
  Gauge32  

adslAturChanTable 1.3.6.1.2.1.10.94.1.1.5
This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturChanEntry

adslAturChanEntry 1.3.6.1.2.1.10.94.1.1.5.1
An entry in the adslAturChanTable.
OBJECT-TYPE    
  AdslAturChanEntry  

adslAturChanInterleaveDelay 1.3.6.1.2.1.10.94.1.1.5.1.1
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.
OBJECT-TYPE    
  Gauge32  

adslAturChanCurrTxRate 1.3.6.1.2.1.10.94.1.1.5.1.2
Actual transmit rate on this channel.
OBJECT-TYPE    
  Gauge32  

adslAturChanPrevTxRate 1.3.6.1.2.1.10.94.1.1.5.1.3
The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.
OBJECT-TYPE    
  Gauge32  

adslAturChanCrcBlockLength 1.3.6.1.2.1.10.94.1.1.5.1.4
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
OBJECT-TYPE    
  Gauge32  

adslAtucPerfDataTable 1.3.6.1.2.1.10.94.1.1.6
This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucPerfDataEntry

adslAtucPerfDataEntry 1.3.6.1.2.1.10.94.1.1.6.1
An entry in adslAtucPerfDataTable.
OBJECT-TYPE    
  AdslAtucPerfDataEntry  

adslAtucPerfLofs 1.3.6.1.2.1.10.94.1.1.6.1.1
Count of the number of Loss of Framing failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucPerfLoss 1.3.6.1.2.1.10.94.1.1.6.1.2
Count of the number of Loss of Signal failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucPerfLols 1.3.6.1.2.1.10.94.1.1.6.1.3
Count of the number of Loss of Link failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucPerfLprs 1.3.6.1.2.1.10.94.1.1.6.1.4
Count of the number of Loss of Power failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucPerfESs 1.3.6.1.2.1.10.94.1.1.6.1.5
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  Counter32  

adslAtucPerfInits 1.3.6.1.2.1.10.94.1.1.6.1.6
Count of the line initialization attempts since agent reset. Includes both successful and failed attempts.
OBJECT-TYPE    
  Counter32  

adslAtucPerfValidIntervals 1.3.6.1.2.1.10.94.1.1.6.1.7
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

adslAtucPerfInvalidIntervals 1.3.6.1.2.1.10.94.1.1.6.1.8
The number of intervals in the range from 0 to the value of adslAtucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

adslAtucPerfCurr15MinTimeElapsed 1.3.6.1.2.1.10.94.1.1.6.1.9
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

adslAtucPerfCurr15MinLofs 1.3.6.1.2.1.10.94.1.1.6.1.10
Count of seconds in the current 15 minute interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr15MinLoss 1.3.6.1.2.1.10.94.1.1.6.1.11
Count of seconds in the current 15 minute interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr15MinLols 1.3.6.1.2.1.10.94.1.1.6.1.12
Count of seconds in the current 15 minute interval when there was Loss of Link.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr15MinLprs 1.3.6.1.2.1.10.94.1.1.6.1.13
Count of seconds in the current 15 minute interval when there was Loss of Power.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr15MinESs 1.3.6.1.2.1.10.94.1.1.6.1.14
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr15MinInits 1.3.6.1.2.1.10.94.1.1.6.1.15
Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucPerfCurr1DayTimeElapsed 1.3.6.1.2.1.10.94.1.1.6.1.16
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

adslAtucPerfCurr1DayLofs 1.3.6.1.2.1.10.94.1.1.6.1.17
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfCurr1DayLoss 1.3.6.1.2.1.10.94.1.1.6.1.18
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfCurr1DayLols 1.3.6.1.2.1.10.94.1.1.6.1.19
Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfCurr1DayLprs 1.3.6.1.2.1.10.94.1.1.6.1.20
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfCurr1DayESs 1.3.6.1.2.1.10.94.1.1.6.1.21
Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfCurr1DayInits 1.3.6.1.2.1.10.94.1.1.6.1.22
Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucPerfPrev1DayMoniSecs 1.3.6.1.2.1.10.94.1.1.6.1.23
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

adslAtucPerfPrev1DayLofs 1.3.6.1.2.1.10.94.1.1.6.1.24
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucPerfPrev1DayLoss 1.3.6.1.2.1.10.94.1.1.6.1.25
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucPerfPrev1DayLols 1.3.6.1.2.1.10.94.1.1.6.1.26
Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucPerfPrev1DayLprs 1.3.6.1.2.1.10.94.1.1.6.1.27
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucPerfPrev1DayESs 1.3.6.1.2.1.10.94.1.1.6.1.28
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucPerfPrev1DayInits 1.3.6.1.2.1.10.94.1.1.6.1.29
Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturPerfDataTable 1.3.6.1.2.1.10.94.1.1.7
This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturPerfDataEntry

adslAturPerfDataEntry 1.3.6.1.2.1.10.94.1.1.7.1
An entry in adslAturPerfDataTable.
OBJECT-TYPE    
  AdslAturPerfDataEntry  

adslAturPerfLofs 1.3.6.1.2.1.10.94.1.1.7.1.1
Count of the number of Loss of Framing failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturPerfLoss 1.3.6.1.2.1.10.94.1.1.7.1.2
Count of the number of Loss of Signal failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturPerfLprs 1.3.6.1.2.1.10.94.1.1.7.1.3
Count of the number of Loss of Power failures since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturPerfESs 1.3.6.1.2.1.10.94.1.1.7.1.4
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  Counter32  

adslAturPerfValidIntervals 1.3.6.1.2.1.10.94.1.1.7.1.5
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

adslAturPerfInvalidIntervals 1.3.6.1.2.1.10.94.1.1.7.1.6
The number of intervals in the range from 0 to the value of adslAturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

adslAturPerfCurr15MinTimeElapsed 1.3.6.1.2.1.10.94.1.1.7.1.7
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

adslAturPerfCurr15MinLofs 1.3.6.1.2.1.10.94.1.1.7.1.8
Count of seconds in the current 15 minute interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturPerfCurr15MinLoss 1.3.6.1.2.1.10.94.1.1.7.1.9
Count of seconds in the current 15 minute interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturPerfCurr15MinLprs 1.3.6.1.2.1.10.94.1.1.7.1.10
Count of seconds in the current 15 minute interval when there was Loss of Power.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturPerfCurr15MinESs 1.3.6.1.2.1.10.94.1.1.7.1.11
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturPerfCurr1DayTimeElapsed 1.3.6.1.2.1.10.94.1.1.7.1.12
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

adslAturPerfCurr1DayLofs 1.3.6.1.2.1.10.94.1.1.7.1.13
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturPerfCurr1DayLoss 1.3.6.1.2.1.10.94.1.1.7.1.14
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturPerfCurr1DayLprs 1.3.6.1.2.1.10.94.1.1.7.1.15
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturPerfCurr1DayESs 1.3.6.1.2.1.10.94.1.1.7.1.16
Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturPerfPrev1DayMoniSecs 1.3.6.1.2.1.10.94.1.1.7.1.17
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

adslAturPerfPrev1DayLofs 1.3.6.1.2.1.10.94.1.1.7.1.18
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturPerfPrev1DayLoss 1.3.6.1.2.1.10.94.1.1.7.1.19
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturPerfPrev1DayLprs 1.3.6.1.2.1.10.94.1.1.7.1.20
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturPerfPrev1DayESs 1.3.6.1.2.1.10.94.1.1.7.1.21
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucIntervalTable 1.3.6.1.2.1.10.94.1.1.8
This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucIntervalEntry

adslAtucIntervalEntry 1.3.6.1.2.1.10.94.1.1.8.1
An entry in the adslAtucIntervalTable.
OBJECT-TYPE    
  AdslAtucIntervalEntry  

adslAtucIntervalNumber 1.3.6.1.2.1.10.94.1.1.8.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

adslAtucIntervalLofs 1.3.6.1.2.1.10.94.1.1.8.1.2
Count of seconds in the interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalLoss 1.3.6.1.2.1.10.94.1.1.8.1.3
Count of seconds in the interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalLols 1.3.6.1.2.1.10.94.1.1.8.1.4
Count of seconds in the interval when there was Loss of Link.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalLprs 1.3.6.1.2.1.10.94.1.1.8.1.5
Count of seconds in the interval when there was Loss of Power.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalESs 1.3.6.1.2.1.10.94.1.1.8.1.6
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalInits 1.3.6.1.2.1.10.94.1.1.8.1.7
Count of the line initialization attempts during the interval. Includes both successful and failed attempts.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucIntervalValidData 1.3.6.1.2.1.10.94.1.1.8.1.8
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

adslAturIntervalTable 1.3.6.1.2.1.10.94.1.1.9
This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturIntervalEntry

adslAturIntervalEntry 1.3.6.1.2.1.10.94.1.1.9.1
An entry in the adslAturIntervalTable.
OBJECT-TYPE    
  AdslAturIntervalEntry  

adslAturIntervalNumber 1.3.6.1.2.1.10.94.1.1.9.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

adslAturIntervalLofs 1.3.6.1.2.1.10.94.1.1.9.1.2
Count of seconds in the interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturIntervalLoss 1.3.6.1.2.1.10.94.1.1.9.1.3
Count of seconds in the interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturIntervalLprs 1.3.6.1.2.1.10.94.1.1.9.1.4
Count of seconds in the interval when there was Loss of Power.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturIntervalESs 1.3.6.1.2.1.10.94.1.1.9.1.5
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturIntervalValidData 1.3.6.1.2.1.10.94.1.1.9.1.6
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

adslAtucChanPerfDataTable 1.3.6.1.2.1.10.94.1.1.10
This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucChanPerfDataEntry

adslAtucChanPerfDataEntry 1.3.6.1.2.1.10.94.1.1.10.1
An entry in adslAtucChanPerfDataTable.
OBJECT-TYPE    
  AdslAtucChanPerfDataEntry  

adslAtucChanReceivedBlks 1.3.6.1.2.1.10.94.1.1.10.1.1
Count of all encoded blocks received on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucChanTransmittedBlks 1.3.6.1.2.1.10.94.1.1.10.1.2
Count of all encoded blocks transmitted on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucChanCorrectedBlks 1.3.6.1.2.1.10.94.1.1.10.1.3
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
OBJECT-TYPE    
  Counter32  

adslAtucChanUncorrectBlks 1.3.6.1.2.1.10.94.1.1.10.1.4
Count of all blocks received with uncorrectable errors since agent reset.
OBJECT-TYPE    
  Counter32  

adslAtucChanPerfValidIntervals 1.3.6.1.2.1.10.94.1.1.10.1.5
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

adslAtucChanPerfInvalidIntervals 1.3.6.1.2.1.10.94.1.1.10.1.6
The number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

adslAtucChanPerfCurr15MinTimeElapsed 1.3.6.1.2.1.10.94.1.1.10.1.7
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

adslAtucChanPerfCurr15MinReceivedBlks 1.3.6.1.2.1.10.94.1.1.10.1.8
Count of all encoded blocks received on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucChanPerfCurr15MinTransmittedBlks 1.3.6.1.2.1.10.94.1.1.10.1.9
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucChanPerfCurr15MinCorrectedBlks 1.3.6.1.2.1.10.94.1.1.10.1.10
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucChanPerfCurr15MinUncorrectBlks 1.3.6.1.2.1.10.94.1.1.10.1.11
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAtucChanPerfCurr1DayTimeElapsed 1.3.6.1.2.1.10.94.1.1.10.1.12
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

adslAtucChanPerfCurr1DayReceivedBlks 1.3.6.1.2.1.10.94.1.1.10.1.13
Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucChanPerfCurr1DayTransmittedBlks 1.3.6.1.2.1.10.94.1.1.10.1.14
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucChanPerfCurr1DayCorrectedBlks 1.3.6.1.2.1.10.94.1.1.10.1.15
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucChanPerfCurr1DayUncorrectBlks 1.3.6.1.2.1.10.94.1.1.10.1.16
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAtucChanPerfPrev1DayMoniSecs 1.3.6.1.2.1.10.94.1.1.10.1.17
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

adslAtucChanPerfPrev1DayReceivedBlks 1.3.6.1.2.1.10.94.1.1.10.1.18
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucChanPerfPrev1DayTransmittedBlks 1.3.6.1.2.1.10.94.1.1.10.1.19
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucChanPerfPrev1DayCorrectedBlks 1.3.6.1.2.1.10.94.1.1.10.1.20
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucChanPerfPrev1DayUncorrectBlks 1.3.6.1.2.1.10.94.1.1.10.1.21
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturChanPerfDataTable 1.3.6.1.2.1.10.94.1.1.11
This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturChanPerfDataEntry

adslAturChanPerfDataEntry 1.3.6.1.2.1.10.94.1.1.11.1
An entry in adslAturChanPerfDataTable.
OBJECT-TYPE    
  AdslAturChanPerfDataEntry  

adslAturChanReceivedBlks 1.3.6.1.2.1.10.94.1.1.11.1.1
Count of all encoded blocks received on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturChanTransmittedBlks 1.3.6.1.2.1.10.94.1.1.11.1.2
Count of all encoded blocks transmitted on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturChanCorrectedBlks 1.3.6.1.2.1.10.94.1.1.11.1.3
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
OBJECT-TYPE    
  Counter32  

adslAturChanUncorrectBlks 1.3.6.1.2.1.10.94.1.1.11.1.4
Count of all blocks received with uncorrectable errors since agent reset.
OBJECT-TYPE    
  Counter32  

adslAturChanPerfValidIntervals 1.3.6.1.2.1.10.94.1.1.11.1.5
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

adslAturChanPerfInvalidIntervals 1.3.6.1.2.1.10.94.1.1.11.1.6
The number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

adslAturChanPerfCurr15MinTimeElapsed 1.3.6.1.2.1.10.94.1.1.11.1.7
Total elapsed seconds in this interval. A full interval is 900 seconds.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

adslAturChanPerfCurr15MinReceivedBlks 1.3.6.1.2.1.10.94.1.1.11.1.8
Count of all encoded blocks received on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturChanPerfCurr15MinTransmittedBlks 1.3.6.1.2.1.10.94.1.1.11.1.9
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturChanPerfCurr15MinCorrectedBlks 1.3.6.1.2.1.10.94.1.1.11.1.10
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturChanPerfCurr15MinUncorrectBlks 1.3.6.1.2.1.10.94.1.1.11.1.11
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

adslAturChanPerfCurr1DayTimeElapsed 1.3.6.1.2.1.10.94.1.1.11.1.12
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

adslAturChanPerfCurr1DayReceivedBlks 1.3.6.1.2.1.10.94.1.1.11.1.13
Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturChanPerfCurr1DayTransmittedBlks 1.3.6.1.2.1.10.94.1.1.11.1.14
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturChanPerfCurr1DayCorrectedBlks 1.3.6.1.2.1.10.94.1.1.11.1.15
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturChanPerfCurr1DayUncorrectBlks 1.3.6.1.2.1.10.94.1.1.11.1.16
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

adslAturChanPerfPrev1DayMoniSecs 1.3.6.1.2.1.10.94.1.1.11.1.17
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

adslAturChanPerfPrev1DayReceivedBlks 1.3.6.1.2.1.10.94.1.1.11.1.18
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturChanPerfPrev1DayTransmittedBlks 1.3.6.1.2.1.10.94.1.1.11.1.19
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturChanPerfPrev1DayCorrectedBlks 1.3.6.1.2.1.10.94.1.1.11.1.20
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAturChanPerfPrev1DayUncorrectBlks 1.3.6.1.2.1.10.94.1.1.11.1.21
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

adslAtucChanIntervalTable 1.3.6.1.2.1.10.94.1.1.12
This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucChanIntervalEntry

adslAtucChanIntervalEntry 1.3.6.1.2.1.10.94.1.1.12.1
An entry in the adslAtucIntervalTable.
OBJECT-TYPE    
  AdslAtucChanIntervalEntry  

adslAtucChanIntervalNumber 1.3.6.1.2.1.10.94.1.1.12.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

adslAtucChanIntervalReceivedBlks 1.3.6.1.2.1.10.94.1.1.12.1.2
Count of all encoded blocks received on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucChanIntervalTransmittedBlks 1.3.6.1.2.1.10.94.1.1.12.1.3
Count of all encoded blocks transmitted on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucChanIntervalCorrectedBlks 1.3.6.1.2.1.10.94.1.1.12.1.4
Count of all blocks received with errors that were corrected on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucChanIntervalUncorrectBlks 1.3.6.1.2.1.10.94.1.1.12.1.5
Count of all blocks received with uncorrectable errors on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAtucChanIntervalValidData 1.3.6.1.2.1.10.94.1.1.12.1.6
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

adslAturChanIntervalTable 1.3.6.1.2.1.10.94.1.1.13
This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturChanIntervalEntry

adslAturChanIntervalEntry 1.3.6.1.2.1.10.94.1.1.13.1
An entry in the adslAturIntervalTable.
OBJECT-TYPE    
  AdslAturChanIntervalEntry  

adslAturChanIntervalNumber 1.3.6.1.2.1.10.94.1.1.13.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

adslAturChanIntervalReceivedBlks 1.3.6.1.2.1.10.94.1.1.13.1.2
Count of all encoded blocks received on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturChanIntervalTransmittedBlks 1.3.6.1.2.1.10.94.1.1.13.1.3
Count of all encoded blocks transmitted on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturChanIntervalCorrectedBlks 1.3.6.1.2.1.10.94.1.1.13.1.4
Count of all blocks received with errors that were corrected on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturChanIntervalUncorrectBlks 1.3.6.1.2.1.10.94.1.1.13.1.5
Count of all blocks received with uncorrectable errors on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

adslAturChanIntervalValidData 1.3.6.1.2.1.10.94.1.1.13.1.6
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

adslLineConfProfileTable 1.3.6.1.2.1.10.94.1.1.14
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line.
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineConfProfileEntry

adslLineConfProfileEntry 1.3.6.1.2.1.10.94.1.1.14.1
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index.
OBJECT-TYPE    
  AdslLineConfProfileEntry  

adslLineConfProfileName 1.3.6.1.2.1.10.94.1.1.14.1.1
This object is used by the line configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..32)  

adslAtucConfRateMode 1.3.6.1.2.1.10.94.1.1.14.1.2
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
OBJECT-TYPE    
  INTEGER fixed(1), adaptAtStartup(2), adaptAtRuntime(3)  

adslAtucConfRateChanRatio 1.3.6.1.2.1.10.94.1.1.14.1.3
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAtucConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage.
OBJECT-TYPE    
  INTEGER 0..100  

adslAtucConfTargetSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.4
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

adslAtucConfMaxSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.5
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

adslAtucConfMinSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.6
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

adslAtucConfDownshiftSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.7
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

adslAtucConfUpshiftSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.8
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

adslAtucConfMinUpshiftTime 1.3.6.1.2.1.10.94.1.1.14.1.9
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

adslAtucConfMinDownshiftTime 1.3.6.1.2.1.10.94.1.1.14.1.10
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

adslAtucChanConfFastMinTxRate 1.3.6.1.2.1.10.94.1.1.14.1.11
Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAtucChanConfInterleaveMinTxRate 1.3.6.1.2.1.10.94.1.1.14.1.12
Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAtucChanConfFastMaxTxRate 1.3.6.1.2.1.10.94.1.1.14.1.13
Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAtucChanConfInterleaveMaxTxRate 1.3.6.1.2.1.10.94.1.1.14.1.14
Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAtucChanConfMaxInterleaveDelay 1.3.6.1.2.1.10.94.1.1.14.1.15
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 0..255  

adslAturConfRateMode 1.3.6.1.2.1.10.94.1.1.14.1.16
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
OBJECT-TYPE    
  INTEGER fixed(1), adaptAtStartup(2), adaptAtRuntime(3)  

adslAturConfRateChanRatio 1.3.6.1.2.1.10.94.1.1.14.1.17
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage.
OBJECT-TYPE    
  INTEGER 0..100  

adslAturConfTargetSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.18
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

adslAturConfMaxSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.19
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

adslAturConfMinSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.20
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

adslAturConfDownshiftSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.21
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

adslAturConfUpshiftSnrMgn 1.3.6.1.2.1.10.94.1.1.14.1.22
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

adslAturConfMinUpshiftTime 1.3.6.1.2.1.10.94.1.1.14.1.23
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

adslAturConfMinDownshiftTime 1.3.6.1.2.1.10.94.1.1.14.1.24
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

adslAturChanConfFastMinTxRate 1.3.6.1.2.1.10.94.1.1.14.1.25
Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAturChanConfInterleaveMinTxRate 1.3.6.1.2.1.10.94.1.1.14.1.26
Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAturChanConfFastMaxTxRate 1.3.6.1.2.1.10.94.1.1.14.1.27
Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAturChanConfInterleaveMaxTxRate 1.3.6.1.2.1.10.94.1.1.14.1.28
Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates.
OBJECT-TYPE    
  Unsigned32  

adslAturChanConfMaxInterleaveDelay 1.3.6.1.2.1.10.94.1.1.14.1.29
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 0..255  

adslLineConfProfileRowStatus 1.3.6.1.2.1.10.94.1.1.14.1.30
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'.
OBJECT-TYPE    
  RowStatus  

adslLineAlarmConfProfileTable 1.3.6.1.2.1.10.94.1.1.15
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineAlarmConfProfileEntry

adslLineAlarmConfProfileEntry 1.3.6.1.2.1.10.94.1.1.15.1
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index.
OBJECT-TYPE    
  AdslLineAlarmConfProfileEntry  

adslLineAlarmConfProfileName 1.3.6.1.2.1.10.94.1.1.15.1.1
This object is used by the line alarm configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..32)  

adslAtucThresh15MinLofs 1.3.6.1.2.1.10.94.1.1.15.1.2
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAtucThresh15MinLoss 1.3.6.1.2.1.10.94.1.1.15.1.3
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAtucThresh15MinLols 1.3.6.1.2.1.10.94.1.1.15.1.4
The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAtucThresh15MinLprs 1.3.6.1.2.1.10.94.1.1.15.1.5
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAtucThresh15MinESs 1.3.6.1.2.1.10.94.1.1.15.1.6
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAtucThreshFastRateUp 1.3.6.1.2.1.10.94.1.1.15.1.7
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAtucThreshInterleaveRateUp 1.3.6.1.2.1.10.94.1.1.15.1.8
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAtucThreshFastRateDown 1.3.6.1.2.1.10.94.1.1.15.1.9
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAtucThreshInterleaveRateDown 1.3.6.1.2.1.10.94.1.1.15.1.10
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAtucInitFailureTrapEnable 1.3.6.1.2.1.10.94.1.1.15.1.11
Enables and disables the InitFailureTrap. This object is defaulted disable(2).
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslAturThresh15MinLofs 1.3.6.1.2.1.10.94.1.1.15.1.12
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAturThresh15MinLoss 1.3.6.1.2.1.10.94.1.1.15.1.13
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAturThresh15MinLprs 1.3.6.1.2.1.10.94.1.1.15.1.14
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAturThresh15MinESs 1.3.6.1.2.1.10.94.1.1.15.1.15
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

adslAturThreshFastRateUp 1.3.6.1.2.1.10.94.1.1.15.1.16
Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAturThreshInterleaveRateUp 1.3.6.1.2.1.10.94.1.1.15.1.17
Applies to `Interleave' channels only. configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAturThreshFastRateDown 1.3.6.1.2.1.10.94.1.1.15.1.18
Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslAturThreshInterleaveRateDown 1.3.6.1.2.1.10.94.1.1.15.1.19
Applies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32  

adslLineAlarmConfProfileRowStatus 1.3.6.1.2.1.10.94.1.1.15.1.20
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'.
OBJECT-TYPE    
  RowStatus  

adslLCSMib 1.3.6.1.2.1.10.94.1.1.16
OBJECT IDENTIFIER    

adslTraps 1.3.6.1.2.1.10.94.1.2
OBJECT IDENTIFIER    

adslAtucTraps 1.3.6.1.2.1.10.94.1.2.1
OBJECT IDENTIFIER    

adslAtucPerfLofsThreshTrap 1.3.6.1.2.1.10.94.1.2.1.0.1
Loss of Framing 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAtucPerfCurr15MinLofs  
  adslAtucThresh15MinLofs  

adslAtucPerfLossThreshTrap 1.3.6.1.2.1.10.94.1.2.1.0.2
Loss of Signal 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAtucPerfCurr15MinLoss  
  adslAtucThresh15MinLoss  

adslAtucPerfLprsThreshTrap 1.3.6.1.2.1.10.94.1.2.1.0.3
Loss of Power 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAtucPerfCurr15MinLprs  
  adslAtucThresh15MinLprs  

adslAtucPerfESsThreshTrap 1.3.6.1.2.1.10.94.1.2.1.0.4
Errored Second 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAtucPerfCurr15MinESs  
  adslAtucThresh15MinESs  

adslAtucRateChangeTrap 1.3.6.1.2.1.10.94.1.2.1.0.5
The ATUCs transmit rate has changed (RADSL mode only)
NOTIFICATION-TYPE    
  adslAtucChanCurrTxRate  
  adslAtucChanPrevTxRate  

adslAtucPerfLolsThreshTrap 1.3.6.1.2.1.10.94.1.2.1.0.6
Loss of Link 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAtucPerfCurr15MinLols  
  adslAtucThresh15MinLols  

adslAtucInitFailureTrap 1.3.6.1.2.1.10.94.1.2.1.0.7
ATUC initialization failed. See adslAtucCurrStatus for potential reasons.
NOTIFICATION-TYPE    
  adslAtucCurrStatus  

adslAturTraps 1.3.6.1.2.1.10.94.1.2.2
OBJECT IDENTIFIER    

adslAturPerfLofsThreshTrap 1.3.6.1.2.1.10.94.1.2.2.0.1
Loss of Framing 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAturPerfCurr15MinLofs  
  adslAturThresh15MinLofs  

adslAturPerfLossThreshTrap 1.3.6.1.2.1.10.94.1.2.2.0.2
Loss of Signal 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAturPerfCurr15MinLoss  
  adslAturThresh15MinLoss  

adslAturPerfLprsThreshTrap 1.3.6.1.2.1.10.94.1.2.2.0.3
Loss of Power 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAturPerfCurr15MinLprs  
  adslAturThresh15MinLprs  

adslAturPerfESsThreshTrap 1.3.6.1.2.1.10.94.1.2.2.0.4
Errored Second 15-minute interval threshold reached.
NOTIFICATION-TYPE    
  adslAturPerfCurr15MinESs  
  adslAturThresh15MinESs  

adslAturRateChangeTrap 1.3.6.1.2.1.10.94.1.2.2.0.5
The ATURs transmit rate has changed (RADSL mode only)
NOTIFICATION-TYPE    
  adslAturChanCurrTxRate  
  adslAturChanPrevTxRate  

adslConformance 1.3.6.1.2.1.10.94.1.3
OBJECT IDENTIFIER    

adslGroups 1.3.6.1.2.1.10.94.1.3.1
OBJECT IDENTIFIER    

adslLineGroup 1.3.6.1.2.1.10.94.1.3.1.1
A collection of objects providing configuration information about an ADSL Line.
OBJECT-GROUP    

adslPhysicalGroup 1.3.6.1.2.1.10.94.1.3.1.2
A collection of objects providing physical configuration information of the ADSL Line.
OBJECT-GROUP    

adslChannelGroup 1.3.6.1.2.1.10.94.1.3.1.3
A collection of objects providing configuration information about an ADSL channel.
OBJECT-GROUP    

adslAtucPhysPerfRawCounterGroup 1.3.6.1.2.1.10.94.1.3.1.4
A collection of objects providing raw performance counts on an ADSL Line (ATU-C end).
OBJECT-GROUP    

adslAtucPhysPerfIntervalGroup 1.3.6.1.2.1.10.94.1.3.1.5
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) .
OBJECT-GROUP    

adslAturPhysPerfRawCounterGroup 1.3.6.1.2.1.10.94.1.3.1.6
A collection of objects providing raw performance counts on an ADSL Line (ATU-R end).
OBJECT-GROUP    

adslAturPhysPerfIntervalGroup 1.3.6.1.2.1.10.94.1.3.1.7
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end).
OBJECT-GROUP    

adslAtucChanPerformanceGroup 1.3.6.1.2.1.10.94.1.3.1.8
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end).
OBJECT-GROUP    

adslAturChanPerformanceGroup 1.3.6.1.2.1.10.94.1.3.1.9
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end).
OBJECT-GROUP    

adslLineConfProfileGroup 1.3.6.1.2.1.10.94.1.3.1.10
A collection of objects providing provisioning information about an ADSL Line.
OBJECT-GROUP    

adslLineAlarmConfProfileGroup 1.3.6.1.2.1.10.94.1.3.1.11
A collection of objects providing alarm provisioning information about an ADSL Line.
OBJECT-GROUP    

adslLineConfProfileControlGroup 1.3.6.1.2.1.10.94.1.3.1.12
A collection of objects providing profile control for the ADSL system.
OBJECT-GROUP    

adslNotificationsGroup 1.3.6.1.2.1.10.94.1.3.1.13
The collection of adsl notifications.
NOTIFICATION-GROUP    

adslAturLineGroup 1.3.6.1.2.1.10.94.1.3.1.14
A collection of objects providing configuration information about an ADSL Line on the ATU-R side.
OBJECT-GROUP    

adslAturPhysicalGroup 1.3.6.1.2.1.10.94.1.3.1.15
A collection of objects providing physical configuration information of the ADSL Line on the ATU-R side.
OBJECT-GROUP    

adslAturChannelGroup 1.3.6.1.2.1.10.94.1.3.1.16
A collection of objects providing configuration information about an ADSL channel on the ATU-R side.
OBJECT-GROUP    

adslAturAtucPhysPerfRawCounterGroup 1.3.6.1.2.1.10.94.1.3.1.17
A collection of objects providing raw performance counts on an ADSL Line (ATU-C end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturAtucPhysPerfIntervalGroup 1.3.6.1.2.1.10.94.1.3.1.18
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturAturPhysPerfRawCounterGroup 1.3.6.1.2.1.10.94.1.3.1.19
A collection of objects providing raw performance counts on an ADSL Line (ATU-R end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturAturPhysPerfIntervalGroup 1.3.6.1.2.1.10.94.1.3.1.20
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturAtucChanPerformanceGroup 1.3.6.1.2.1.10.94.1.3.1.21
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturAturChanPerformanceGroup 1.3.6.1.2.1.10.94.1.3.1.22
A collection of objects providing channel block performance information on an ADSL channel (ATU-R end) provided by the ATU-R agent.
OBJECT-GROUP    

adslAturLineAlarmConfProfileGroup 1.3.6.1.2.1.10.94.1.3.1.23
A collection of objects providing alarm provisioning information about an ADSL Line provided by the ATU-R agent.
OBJECT-GROUP    

adslAturLineConfProfileControlGroup 1.3.6.1.2.1.10.94.1.3.1.24
A collection of objects providing profile control for the ADSL system by the ATU-R agent.
OBJECT-GROUP    

adslAturNotificationsGroup 1.3.6.1.2.1.10.94.1.3.1.25
The collection of ADSL notifications implemented by the ATU-R agent.
NOTIFICATION-GROUP    

adslCompliances 1.3.6.1.2.1.10.94.1.3.2
OBJECT IDENTIFIER    

adslLineMibAtucCompliance 1.3.6.1.2.1.10.94.1.3.2.1
The compliance statement for SNMP entities which manage ADSL ATU-C interfaces.
MODULE-COMPLIANCE    

adslLineMibAturCompliance 1.3.6.1.2.1.10.94.1.3.2.2
The compliance statement for SNMP entities which manage ADSL ATU-R interfaces.
MODULE-COMPLIANCE    

Defined Objects

AdslLineEntry  
SEQUENCE    
  AdslLineCodingType as adslLineCoding  
  INTEGER as adslLineType  
  VariablePointer as adslLineSpecific  
  SnmpAdminString as adslLineConfProfile  
  SnmpAdminString as adslLineAlarmConfProfile  

AdslAtucPhysEntry  
SEQUENCE    
  SnmpAdminString as adslAtucInvSerialNumber  
  SnmpAdminString as adslAtucInvVendorID  
  SnmpAdminString as adslAtucInvVersionNumber  
  INTEGER as adslAtucCurrSnrMgn  
  Gauge32 as adslAtucCurrAtn  
  BITS as adslAtucCurrStatus  
  INTEGER as adslAtucCurrOutputPwr  
  Gauge32 as adslAtucCurrAttainableRate  

AdslAturPhysEntry  
SEQUENCE    
  SnmpAdminString as adslAturInvSerialNumber  
  SnmpAdminString as adslAturInvVendorID  
  SnmpAdminString as adslAturInvVersionNumber  
  INTEGER as adslAturCurrSnrMgn  
  Gauge32 as adslAturCurrAtn  
  BITS as adslAturCurrStatus  
  INTEGER as adslAturCurrOutputPwr  
  Gauge32 as adslAturCurrAttainableRate  

AdslAtucChanEntry  
SEQUENCE    
  Gauge32 as adslAtucChanInterleaveDelay  
  Gauge32 as adslAtucChanCurrTxRate  
  Gauge32 as adslAtucChanPrevTxRate  
  Gauge32 as adslAtucChanCrcBlockLength  

AdslAturChanEntry  
SEQUENCE    
  Gauge32 as adslAturChanInterleaveDelay  
  Gauge32 as adslAturChanCurrTxRate  
  Gauge32 as adslAturChanPrevTxRate  
  Gauge32 as adslAturChanCrcBlockLength  

AdslAtucPerfDataEntry  
SEQUENCE    
  Counter32 as adslAtucPerfLofs  
  Counter32 as adslAtucPerfLoss  
  Counter32 as adslAtucPerfLols  
  Counter32 as adslAtucPerfLprs  
  Counter32 as adslAtucPerfESs  
  Counter32 as adslAtucPerfInits  
  INTEGER as adslAtucPerfValidIntervals  
  INTEGER as adslAtucPerfInvalidIntervals  
  AdslPerfTimeElapsed as adslAtucPerfCurr15MinTimeElapsed  
  PerfCurrentCount as adslAtucPerfCurr15MinLofs  
  PerfCurrentCount as adslAtucPerfCurr15MinLoss  
  PerfCurrentCount as adslAtucPerfCurr15MinLols  
  PerfCurrentCount as adslAtucPerfCurr15MinLprs  
  PerfCurrentCount as adslAtucPerfCurr15MinESs  
  PerfCurrentCount as adslAtucPerfCurr15MinInits  
  AdslPerfTimeElapsed as adslAtucPerfCurr1DayTimeElapsed  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayLofs  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayLoss  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayLols  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayLprs  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayESs  
  AdslPerfCurrDayCount as adslAtucPerfCurr1DayInits  
  INTEGER as adslAtucPerfPrev1DayMoniSecs  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayLofs  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayLoss  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayLols  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayLprs  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayESs  
  AdslPerfPrevDayCount as adslAtucPerfPrev1DayInits  

AdslAturPerfDataEntry  
SEQUENCE    
  Counter32 as adslAturPerfLofs  
  Counter32 as adslAturPerfLoss  
  Counter32 as adslAturPerfLprs  
  Counter32 as adslAturPerfESs  
  INTEGER as adslAturPerfValidIntervals  
  INTEGER as adslAturPerfInvalidIntervals  
  AdslPerfTimeElapsed as adslAturPerfCurr15MinTimeElapsed  
  PerfCurrentCount as adslAturPerfCurr15MinLofs  
  PerfCurrentCount as adslAturPerfCurr15MinLoss  
  PerfCurrentCount as adslAturPerfCurr15MinLprs  
  PerfCurrentCount as adslAturPerfCurr15MinESs  
  AdslPerfTimeElapsed as adslAturPerfCurr1DayTimeElapsed  
  AdslPerfCurrDayCount as adslAturPerfCurr1DayLofs  
  AdslPerfCurrDayCount as adslAturPerfCurr1DayLoss  
  AdslPerfCurrDayCount as adslAturPerfCurr1DayLprs  
  AdslPerfCurrDayCount as adslAturPerfCurr1DayESs  
  INTEGER as adslAturPerfPrev1DayMoniSecs  
  AdslPerfPrevDayCount as adslAturPerfPrev1DayLofs  
  AdslPerfPrevDayCount as adslAturPerfPrev1DayLoss  
  AdslPerfPrevDayCount as adslAturPerfPrev1DayLprs  
  AdslPerfPrevDayCount as adslAturPerfPrev1DayESs  

AdslAtucIntervalEntry  
SEQUENCE    
  INTEGER as adslAtucIntervalNumber  
  PerfIntervalCount as adslAtucIntervalLofs  
  PerfIntervalCount as adslAtucIntervalLoss  
  PerfIntervalCount as adslAtucIntervalLols  
  PerfIntervalCount as adslAtucIntervalLprs  
  PerfIntervalCount as adslAtucIntervalESs  
  PerfIntervalCount as adslAtucIntervalInits  
  TruthValue as adslAtucIntervalValidData  

AdslAturIntervalEntry  
SEQUENCE    
  INTEGER as adslAturIntervalNumber  
  PerfIntervalCount as adslAturIntervalLofs  
  PerfIntervalCount as adslAturIntervalLoss  
  PerfIntervalCount as adslAturIntervalLprs  
  PerfIntervalCount as adslAturIntervalESs  
  TruthValue as adslAturIntervalValidData  

AdslAtucChanPerfDataEntry  
SEQUENCE    
  Counter32 as adslAtucChanReceivedBlks  
  Counter32 as adslAtucChanTransmittedBlks  
  Counter32 as adslAtucChanCorrectedBlks  
  Counter32 as adslAtucChanUncorrectBlks  
  INTEGER as adslAtucChanPerfValidIntervals  
  INTEGER as adslAtucChanPerfInvalidIntervals  
  AdslPerfTimeElapsed as adslAtucChanPerfCurr15MinTimeElapsed  
  PerfCurrentCount as adslAtucChanPerfCurr15MinReceivedBlks  
  PerfCurrentCount as adslAtucChanPerfCurr15MinTransmittedBlks  
  PerfCurrentCount as adslAtucChanPerfCurr15MinCorrectedBlks  
  PerfCurrentCount as adslAtucChanPerfCurr15MinUncorrectBlks  
  AdslPerfTimeElapsed as adslAtucChanPerfCurr1DayTimeElapsed  
  AdslPerfCurrDayCount as adslAtucChanPerfCurr1DayReceivedBlks  
  AdslPerfCurrDayCount as adslAtucChanPerfCurr1DayTransmittedBlks  
  AdslPerfCurrDayCount as adslAtucChanPerfCurr1DayCorrectedBlks  
  AdslPerfCurrDayCount as adslAtucChanPerfCurr1DayUncorrectBlks  
  INTEGER as adslAtucChanPerfPrev1DayMoniSecs  
  AdslPerfPrevDayCount as adslAtucChanPerfPrev1DayReceivedBlks  
  AdslPerfPrevDayCount as adslAtucChanPerfPrev1DayTransmittedBlks  
  AdslPerfPrevDayCount as adslAtucChanPerfPrev1DayCorrectedBlks  
  AdslPerfPrevDayCount as adslAtucChanPerfPrev1DayUncorrectBlks  

AdslAturChanPerfDataEntry  
SEQUENCE    
  Counter32 as adslAturChanReceivedBlks  
  Counter32 as adslAturChanTransmittedBlks  
  Counter32 as adslAturChanCorrectedBlks  
  Counter32 as adslAturChanUncorrectBlks  
  INTEGER as adslAturChanPerfValidIntervals  
  INTEGER as adslAturChanPerfInvalidIntervals  
  AdslPerfTimeElapsed as adslAturChanPerfCurr15MinTimeElapsed  
  PerfCurrentCount as adslAturChanPerfCurr15MinReceivedBlks  
  PerfCurrentCount as adslAturChanPerfCurr15MinTransmittedBlks  
  PerfCurrentCount as adslAturChanPerfCurr15MinCorrectedBlks  
  PerfCurrentCount as adslAturChanPerfCurr15MinUncorrectBlks  
  AdslPerfTimeElapsed as adslAturChanPerfCurr1DayTimeElapsed  
  AdslPerfCurrDayCount as adslAturChanPerfCurr1DayReceivedBlks  
  AdslPerfCurrDayCount as adslAturChanPerfCurr1DayTransmittedBlks  
  AdslPerfCurrDayCount as adslAturChanPerfCurr1DayCorrectedBlks  
  AdslPerfCurrDayCount as adslAturChanPerfCurr1DayUncorrectBlks  
  INTEGER as adslAturChanPerfPrev1DayMoniSecs  
  AdslPerfPrevDayCount as adslAturChanPerfPrev1DayReceivedBlks  
  AdslPerfPrevDayCount as adslAturChanPerfPrev1DayTransmittedBlks  
  AdslPerfPrevDayCount as adslAturChanPerfPrev1DayCorrectedBlks  
  AdslPerfPrevDayCount as adslAturChanPerfPrev1DayUncorrectBlks  

AdslAtucChanIntervalEntry  
SEQUENCE    
  INTEGER as adslAtucChanIntervalNumber  
  PerfIntervalCount as adslAtucChanIntervalReceivedBlks  
  PerfIntervalCount as adslAtucChanIntervalTransmittedBlks  
  PerfIntervalCount as adslAtucChanIntervalCorrectedBlks  
  PerfIntervalCount as adslAtucChanIntervalUncorrectBlks  
  TruthValue as adslAtucChanIntervalValidData  

AdslAturChanIntervalEntry  
SEQUENCE    
  INTEGER as adslAturChanIntervalNumber  
  PerfIntervalCount as adslAturChanIntervalReceivedBlks  
  PerfIntervalCount as adslAturChanIntervalTransmittedBlks  
  PerfIntervalCount as adslAturChanIntervalCorrectedBlks  
  PerfIntervalCount as adslAturChanIntervalUncorrectBlks  
  TruthValue as adslAturChanIntervalValidData  

AdslLineConfProfileEntry  
SEQUENCE    
  SnmpAdminString as adslLineConfProfileName  
  INTEGER as adslAtucConfRateMode  
  INTEGER as adslAtucConfRateChanRatio  
  INTEGER as adslAtucConfTargetSnrMgn  
  INTEGER as adslAtucConfMaxSnrMgn  
  INTEGER as adslAtucConfMinSnrMgn  
  INTEGER as adslAtucConfDownshiftSnrMgn  
  INTEGER as adslAtucConfUpshiftSnrMgn  
  INTEGER as adslAtucConfMinUpshiftTime  
  INTEGER as adslAtucConfMinDownshiftTime  
  Unsigned32 as adslAtucChanConfFastMinTxRate  
  Unsigned32 as adslAtucChanConfInterleaveMinTxRate  
  Unsigned32 as adslAtucChanConfFastMaxTxRate  
  Unsigned32 as adslAtucChanConfInterleaveMaxTxRate  
  INTEGER as adslAtucChanConfMaxInterleaveDelay  
  INTEGER as adslAturConfRateMode  
  INTEGER as adslAturConfRateChanRatio  
  INTEGER as adslAturConfTargetSnrMgn  
  INTEGER as adslAturConfMaxSnrMgn  
  INTEGER as adslAturConfMinSnrMgn  
  INTEGER as adslAturConfDownshiftSnrMgn  
  INTEGER as adslAturConfUpshiftSnrMgn  
  INTEGER as adslAturConfMinUpshiftTime  
  INTEGER as adslAturConfMinDownshiftTime  
  Unsigned32 as adslAturChanConfFastMinTxRate  
  Unsigned32 as adslAturChanConfInterleaveMinTxRate  
  Unsigned32 as adslAturChanConfFastMaxTxRate  
  Unsigned32 as adslAturChanConfInterleaveMaxTxRate  
  INTEGER as adslAturChanConfMaxInterleaveDelay  
  RowStatus as adslLineConfProfileRowStatus  

AdslLineAlarmConfProfileEntry  
SEQUENCE    
  SnmpAdminString as adslLineAlarmConfProfileName  
  INTEGER as adslAtucThresh15MinLofs  
  INTEGER as adslAtucThresh15MinLoss  
  INTEGER as adslAtucThresh15MinLols  
  INTEGER as adslAtucThresh15MinLprs  
  INTEGER as adslAtucThresh15MinESs  
  Unsigned32 as adslAtucThreshFastRateUp  
  Unsigned32 as adslAtucThreshInterleaveRateUp  
  Unsigned32 as adslAtucThreshFastRateDown  
  Unsigned32 as adslAtucThreshInterleaveRateDown  
  INTEGER as adslAtucInitFailureTrapEnable  
  INTEGER as adslAturThresh15MinLofs  
  INTEGER as adslAturThresh15MinLoss  
  INTEGER as adslAturThresh15MinLprs  
  INTEGER as adslAturThresh15MinESs  
  Unsigned32 as adslAturThreshFastRateUp  
  Unsigned32 as adslAturThreshInterleaveRateUp  
  Unsigned32 as adslAturThreshFastRateDown  
  Unsigned32 as adslAturThreshInterleaveRateDown  
  RowStatus as adslLineAlarmConfProfileRowStatus