
| SNMPv2-SMI | SNMPv2-TC |
| MODULE-IDENTITY | transmission | TEXTUAL-CONVENTION |
| adsl2TCMIB | 1.3.6.1.2.1.10.238.2 | ||
| This MIB Module provides Textual Conventions to be used by the ADSL2-LINE-MIB module for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices. | |||
| MODULE-IDENTITY | |||
| Adsl2Unit | |||
| Identifies a transceiver as being either an ATU-C or an ATU-R. An ADSL line consists of two transceivers, an ATU-C and an ATU-R. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: atuc(1) -- Central office ADSL terminal unit (ATU-C). atur(2) -- Remote ADSL terminal unit (ATU-R). | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | atuc(1), atur(2) | ||
| Adsl2Direction | |||
| Identifies the direction of a band as being either upstream or downstream. Specified as an INTEGER, the two values are: upstream(1), and downstream(2). | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | upstream(1), downstream(2) | ||
| Adsl2TransmissionModeType | |||
| A set of ADSL2 line transmission modes, with one bit per mode. The notes (F) and (L) denote Full-Rate and Lite/splitterless, respectively: Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 02 : G.992.1 POTS non-overlapped (F) Bit 03 : G.992.1 POTS overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 08 : G.992.2 POTS non-overlapped (L) Bit 09 : G.992.2 POTS overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1 Bit 13-17: Reserved Bit 18 : G.992.3 POTS non-overlapped (F) Bit 19 : G.992.3 POTS overlapped (F) Bit 20 : G.992.3 ISDN non-overlapped (F) Bit 21 : G.992.3 ISDN overlapped (F) Bit 22-23: Reserved Bit 24 : G.992.4 POTS non-overlapped (L) Bit 25 : G.992.4 POTS overlapped (L) Bit 26-27: Reserved Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F) Bit 29 : G.992.3 Annex I All-Digital overlapped (F) Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F) Bit 31 : G.992.3 Annex J All-Digital overlapped (F) Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L) Bit 33 : G.992.4 Annex I All-Digital overlapped (L) Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) Bit 38 : G.992.3 Annex M POTS non-overlapped (F) Bit 39 : G.992.3 Annex M POTS overlapped (F) Bit 40 : G.992.5 POTS non-overlapped (F) Bit 41 : G.992.5 POTS overlapped (F) Bit 42 : G.992.5 ISDN non-overlapped (F) Bit 43 : G.992.5 ISDN overlapped (F) Bit 44-45: Reserved Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F) Bit 47 : G.992.5 Annex I All-Digital overlapped (F) Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F) Bit 49 : G.992.5 Annex J All-Digital overlapped (F) Bit 50 : G.992.5 Annex M POTS non-overlapped (F) Bit 51 : G.992.5 Annex M POTS overlapped (F) Bit 52-55: Reserved | |||
| TEXTUAL-CONVENTION | |||
| BITS | ansit1413(0), etsi(1), g9921PotsNonOverlapped(2), g9921PotsOverlapped(3), g9921IsdnNonOverlapped(4), g9921isdnOverlapped(5), g9921tcmIsdnNonOverlapped(6), g9921tcmIsdnOverlapped(7), g9922potsNonOverlapped(8), g9922potsOverlapped(9), g9922tcmIsdnNonOverlapped(10), g9922tcmIsdnOverlapped(11), g9921tcmIsdnSymmetric(12), reserved1(13), reserved2(14), reserved3(15), reserved4(16), reserved5(17), g9923PotsNonOverlapped(18), g9923PotsOverlapped(19), g9923IsdnNonOverlapped(20), g9923isdnOverlapped(21), reserved6(22), reserved7(23), g9924potsNonOverlapped(24), g9924potsOverlapped(25), reserved8(26), reserved9(27), g9923AnnexIAllDigNonOverlapped(28), g9923AnnexIAllDigOverlapped(29), g9923AnnexJAllDigNonOverlapped(30), g9923AnnexJAllDigOverlapped(31), g9924AnnexIAllDigNonOverlapped(32), g9924AnnexIAllDigOverlapped(33), g9923AnnexLMode1NonOverlapped(34), g9923AnnexLMode2NonOverlapped(35), g9923AnnexLMode3Overlapped(36), g9923AnnexLMode4Overlapped(37), g9923AnnexMPotsNonOverlapped(38), g9923AnnexMPotsOverlapped(39), g9925PotsNonOverlapped(40), g9925PotsOverlapped(41), g9925IsdnNonOverlapped(42), g9925isdnOverlapped(43), reserved10(44), reserved11(45), g9925AnnexIAllDigNonOverlapped(46), g9925AnnexIAllDigOverlapped(47), g9925AnnexJAllDigNonOverlapped(48), g9925AnnexJAllDigOverlapped(49), g9925AnnexMPotsNonOverlapped(50), g9925AnnexMPotsOverlapped(51), reserved12(52), reserved13(53), reserved14(54), reserved15(55) | ||
| Adsl2RaMode | |||
| Specifies the rate adaptation behavior for the line. The three possible behaviors are: manual(1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate. raInit(2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values. dynamicRa(3) - Dynamic Rate-Adaptation during initialization process as well as during SHOWTIME. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | manual(1), raInit(2), dynamicRa(3) | ||
| Adsl2InitResult | |||
| Specifies the result of a full initialization attempt; the six possible result values are: noFail(0) - Successful initialization. configError(1) - Configuration failure. configNotFeasible(2) - Configuration details not supported. commFail(3) - Communication failure. noPeerAtu(4) - Peer ATU not detected. otherCause(5) - Other initialization failure reason. The values used are as defined in ITU-T G.997.1, paragraph 7.5.1.3 | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5) | ||
| Adsl2OperationModes | |||
| The ADSL2 management model specified includes an ADSL Mode attribute that identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. The notes (F) and (L) denote Full-Rate and Lite/splitterless respectively: +-------+--------------------------------------------------+ | Value | ADSL operation mode description | +-------+--------------------------------------------------+ 1 - The default/generic PSD configuration. Default configuration will be used when no other matching mode-specific configuration can be found. 2 - ADSL family. The attributes included in the Mode- Specific PSD Configuration are irrelevant for ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it is possible to map those modes to this generic class. 3-7 - Unused. Reserved for future ITU-T specification. 8 - G.992.3 POTS non-overlapped (F) 9 - G.992.3 POTS overlapped (F) 10 - G.992.3 ISDN non-overlapped (F) 11 - G.992.3 ISDN overlapped (F) 12-13 - Unused. Reserved for future ITU-T specification. 14 - G.992.4 POTS non-overlapped (L) 15 - G.992.4 POTS overlapped (L) 16-17 - Unused. Reserved for future ITU-T specification. 18 - G.992.3 Annex I All-Digital non-overlapped (F) 19 - G.992.3 Annex I All-Digital overlapped (F) 20 - G.992.3 Annex J All-Digital non-overlapped (F) 21 - G.992.3 Annex J All-Digital overlapped (F) 22 - G.992.4 Annex I All-Digital non-overlapped (L) 23 - G.992.4 Annex I All-Digital overlapped (L) 24 - G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) 25 - G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) 26 - G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) 27 - G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) 28 - G.992.3 Annex M POTS non-overlapped (F) 29 - G.992.3 Annex M POTS overlapped (F) 30 - G.992.5 POTS non-overlapped (F) 31 - G.992.5 POTS overlapped (F) 32 - G.992.5 ISDN non-overlapped (F) 33 - G.992.5 ISDN overlapped (F) 34-35 - Unused. Reserved for future ITU-T specification. 36 - G.992.5 Annex I All-Digital non-overlapped (F) 37 - G.992.5 Annex I All-Digital overlapped (F) 38 - G.992.5 Annex J All-Digital non-overlapped (F) 39 - G.992.5 Annex J All-Digital overlapped (F) 40 - G.992.5 Annex M POTS non-overlapped (F) 41 - G.992.5 Annex M POTS overlapped (F) | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | defMode(1), adsl(2), g9923PotsNonOverlapped(8), g9923PotsOverlapped(9), g9923IsdnNonOverlapped(10), g9923isdnOverlapped(11), g9924potsNonOverlapped(14), g9924potsOverlapped(15), g9923AnnexIAllDigNonOverlapped(18), g9923AnnexIAllDigOverlapped(19), g9923AnnexJAllDigNonOverlapped(20), g9923AnnexJAllDigOverlapped(21), g9924AnnexIAllDigNonOverlapped(22), g9924AnnexIAllDigOverlapped(23), g9923AnnexLMode1NonOverlapped(24), g9923AnnexLMode2NonOverlapped(25), g9923AnnexLMode3Overlapped(26), g9923AnnexLMode4Overlapped(27), g9923AnnexMPotsNonOverlapped(28), g9923AnnexMPotsOverlapped(29), g9925PotsNonOverlapped(30), g9925PotsOverlapped(31), g9925IsdnNonOverlapped(32), g9925isdnOverlapped(33), g9925AnnexIAllDigNonOverlapped(36), g9925AnnexIAllDigOverlapped(37), g9925AnnexJAllDigNonOverlapped(38), g9925AnnexJAllDigOverlapped(39), g9925AnnexMPotsNonOverlapped(40), g9925AnnexMPotsOverlapped(41) | ||
| Adsl2PowerMngState | |||
| Attributes with this syntax uniquely identify each power management state defined for the ADSL/ADSL2 or ADSL2+ link. The possible values are: l0(1) - L0 - Full power management state. l1(2) - L1 - Low power management state (for G.992.2). l2(3) - L2 - Low power management state (for G.992.3, G.992.4, and G.992.5). l3(4) - L3 - Idle power management state. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | l0(1), l1(2), l2(3), l3(4) | ||
| Adsl2ConfPmsForce | |||
| Attributes with this syntax are configuration parameters that reference the desired power management state for the ADSL/ADSL2 or ADSL2+ link: l3toL0(0) - Perform a transition from L3 to L0 (Full power management state). l0toL2(2) - Perform a transition from L0 to L2 (Low power management state). l0orL2toL3(3) - Perform a transition into L3 (Idle power management state). The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.3 | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | l3toL0(0), l0toL2(2), l0orL2toL3(3) | ||
| Adsl2LConfProfPmMode | |||
| Attributes with this syntax are configuration parameters that reference the power modes/states into which the ATU-C or ATU-R may autonomously transit. It is a BITS structure that allows control of the following transit options: allowTransitionsToIdle(0) - XTU may autonomously transit to idle (L3) state. allowTransitionsToLowPower(1) - XTU may autonomously transit to low-power (L2) state. | |||
| TEXTUAL-CONVENTION | |||
| BITS | allowTransitionsToIdle(0), allowTransitionsToLowPower(1) | ||
| Adsl2LineLdsf | |||
| Attributes with this syntax are configuration parameters that control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ link. The possible values are: inhibit(0) - Inhibit Loop Diagnostic mode. force(1) - Force/Initiate Loop Diagnostic mode. The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.8 | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | inhibit(0), force(1) | ||
| Adsl2LdsfResult | |||
| Possible failure reasons associated with performing a Dual Ended Loop Test (DELT) on a DSL line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. unsupported(4) - The NE or the line card doesn't support LDSF. cannotRun(5) - The NE cannot initiate the command, due to a nonspecific reason. aborted(6) - The Loop Diagnostics process aborted. failed(7) - The Loop Diagnostics process failed. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp(9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), success(2), inProgress(3), unsupported(4), cannotRun(5), aborted(6), failed(7), illegalMode(8), adminUp(9), tableFull(10), noResources(11) | ||
| Adsl2SymbolProtection | |||
| Attributes with this syntax are configuration parameters that reference the minimum-length impulse noise protection (INP) in terms of number of symbols. The possible values are: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) | ||
| Adsl2MaxBer | |||
| Attributes with this syntax are configuration parameters that reference the maximum Bit Error Rate (BER). The possible values are: eminus3(1) - Maximum BER=E^-3 eminus5(2) - Maximum BER=E^-5 eminus7(3) - Maximum BER=E^-7 | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | eminus3(1), eminus5(2), eminus7(3) | ||
| Adsl2ScMaskDs | |||
| Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is not in use. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..64) | ||
| Adsl2ScMaskUs | |||
| Each one of the 64 bits in this OCTET STRING array represents the corresponding bin in the upstream direction. A value of one indicates that the bin is not in use. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..8) | ||
| Adsl2RfiDs | |||
| Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is part of a notch filter. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..64) | ||
| Adsl2PsdMaskDs | |||
| This is a structure that represents up to 32 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..96) | ||
| Adsl2PsdMaskUs | |||
| This is a structure that represents up to 4 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..12) | ||
| Adsl2Tssi | |||
| This is a structure that represents up to 32 transmit spectrum shaping (TSSi) breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the shaping parameter at the breakpoint. It is a value from 0 to 127 (units of -0.5 dB). The special value 127 indicates that the sub-carrier is not transmitted. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..96) | ||
| Adsl2LastTransmittedState | |||
| This parameter represents the last successfully transmitted initialization state in the last full initialization performed on the line. States are per the specific xDSL technology and are numbered from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | atucG9941(0), atucQuiet1(1), atucComb1(2), atucQuiet2(3), atucComb2(4), atucIcomb1(5), atucLineprob(6), atucQuiet3(7), atucComb3(8), atucIComb2(9), atucMsgfmt(10), atucMsgpcb(11), atucQuiet4(12), atucReverb1(13), atucTref1(14), atucReverb2(15), atucEct(16), atucReverb3(17), atucTref2(18), atucReverb4(19), atucSegue1(20), atucMsg1(21), atucReverb5(22), atucSegue2(23), atucMedley(24), atucExchmarker(25), atucMsg2(26), atucReverb6(27), atucSegue3(28), atucParams(29), atucReverb7(30), atucSegue4(31), atucShowtime(32), aturG9941(100), aturQuiet1(101), aturComb1(102), aturQuiet2(103), aturComb2(104), aturIcomb1(105), aturLineprob(106), aturQuiet3(107), aturComb3(108), aturIcomb2(109), aturMsgfmt(110), aturMsgpcb(111), aturReverb1(112), aturQuiet4(113), aturReverb2(114), aturQuiet5(115), aturReverb3(116), aturEct(117), aturReverb4(118), aturSegue1(119), aturReverb5(120), aturSegue2(121), aturMsg1(122), aturMedley(123), aturExchmarker(124), aturMsg2(125), aturReverb6(126), aturSegue3(127), aturParams(128), aturReverb7(129), aturSegue4(130), aturShowtime(131) | ||
| Adsl2LineStatus | |||
| Attributes with this syntax are status parameters that reflect the failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link. This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. lossOfFrame(1) - Loss of frame synchronization. lossOfSignal(2) - Loss of signal. lossOfPower(3) - Loss of power. Usually this failure may be reported for ATU-Rs only. initFailure(4) - Recent initialization process failed. Never active on ATU-R. | |||
| TEXTUAL-CONVENTION | |||
| BITS | noDefect(0), lossOfFrame(1), lossOfSignal(2), lossOfPower(3), initFailure(4) | ||
| Adsl2ChAtmStatus | |||
| Attributes with this syntax are status parameters that reflect the failure status for Transmission Convergence (TC) layer of a given ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. noCellDelineation(1) - The link was successfully initialized, but cell delineation was never acquired on the associated ATM data path. lossOfCellDelineation(2) - Loss of cell delineation on the associated ATM data path. | |||
| TEXTUAL-CONVENTION | |||
| BITS | noDefect(0), noCellDelineation(1), lossOfCellDelineation(2) | ||
| Adsl2ChPtmStatus | |||
| Attributes with this syntax are status parameters that reflect the failure status for a given PTM interface (packet data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. outOfSync(1) - Out of synchronization. | |||
| TEXTUAL-CONVENTION | |||
| BITS | noDefect(0), outOfSync(1) | ||