
ADSLF-MIB
File:
ADSLF-MIB.mib (29898 bytes)
Imported modules
Imported symbols
Defined Objects
| adslLineCoding |
1.3.6.1.4.1.429.4.32.1 |
| Specifies the ADSL coding type used on this line. Other types may be added in the future with higher values ala ifIANAtype. This is used to create a LCS sub-MIB in the same way ifIANAtype adsl(94) is used to create this MIB. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
dmt(1), cap(2), qam(3) |
|
| adslLineType |
1.3.6.1.4.1.429.4.32.2 |
| this describes which other tables go with this ifEntry. use EITHER three separate ifEntries (and adslLinEntries): (1) and tables 1,2,3, 6,7,8,9 (2) with 1,4,5, and (3) and 1,4,5, OR use values (4) or (5) with tables 1-9 as a single ifEntry/adslLineEntry |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
physical(1), fast(2), interleave(3), physFast(4), physInterleave(5) |
|
| adslLineSpecific |
1.3.6.1.4.1.429.4.32.3 |
| OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATU-C interface in a DSLAM (among other possibilities) |
| OBJECT-TYPE |
|
|
|
| |
OBJECT IDENTIFIER |
|
|
| adslLineStatus |
1.3.6.1.4.1.429.4.32.4 |
| Status indicates mandatory state of the line. This is a bit-map of possible conditions. These are from the perspective of the ATU-C, since any loss of communication with the ATU-R prevents determination of its state. This is intended to supplement ifOperStatus and ifAdminStatus. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
operational(1), lossOfFraming(2), lossOfSignal(3), lossOfPower(4), initFailure(5) |
|
| adslAturPerfCV |
1.3.6.1.4.1.429.4.32.17 |
| count of the number of Loss of Coding Violation events since system reset. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adslAturPerfCurr1DayMoniSecs |
1.3.6.1.4.1.429.4.32.20 |
| The total number of valid seconds in the Curr1Day interval counters. This may be less than adslAturPerfCurr1DayElapSecs only when there were some seconds in the interval when no valid data could be collected. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adslAturPerfPrev1DayMoniSecs |
1.3.6.1.4.1.429.4.32.22 |
| The total number of valid seconds in the Prev1Day interval counters. This may be less than adslAturPerfPrev1DayElapSecs only when there were some seconds in the interval when no valid data could be collected. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adslAturPerfCurr1DayLofs |
1.3.6.1.4.1.429.4.32.23 |
| Count of the number of seconds when there was Loss of Framing during the mandatory day, as measured by adslAturPerfCurr1DayElapSecs. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adslAturChanCurrTxRate |
1.3.6.1.4.1.429.4.32.47 |
| derived from adslAturConfMinTxRate + * (adslAturConfRateChanRatio / 100) as long as it is < adslAturChanConfMaxTxRate |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adslAturChanPrevTxRate |
1.3.6.1.4.1.429.4.32.48 |
| The rate that was set at the previous adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Small rate changes are accumulated until either the rate changes by adslAturChanConfDownDeltaRate or adslAturChanConfUpDeltaRate. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| usrAdslCFMStatusFlag |
1.3.6.1.4.1.429.4.32.53 |
| This variable controls saving and loading of configuration information for the ADSL WAN Driver. The value can be set to either save or load by a management station. The other values indicate if any configuration operation and what type is in progress. |
| OBJECT-TYPE |
|
|
|
| |
UsrConfigStatus |
|
|
| usrAdslCfgFileName |
1.3.6.1.4.1.429.4.32.54 |
| The name of a ConfigFile to read/write the ADSL parameters. If the value of this object is an empty string, then the ADSL Driver uses the default name `@file://adsl.cfg'. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| usrAdslAdiVerson |
1.3.6.1.4.1.429.4.32.58 |
| Value is a number that corresponds to the version number of the ADI chipset. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| usrAdslLocalReqDwnConstStatus |
1.3.6.1.4.1.429.4.32.59 |
| Value corresponds to the local downstream constellation requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-8(1), const-16(2), const-32(3), const-64(4), const-128(5), const-256(6), const-256U(7) |
|
| usrAdslActualUpConstStatus |
1.3.6.1.4.1.429.4.32.60 |
| Value corresponds to the actual upstream constellation that was used, which may differ from the value requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-auto(1), const-8(2), const-8ER(3), const-16(4), const-32(5), const-64(6), const-128(7), const-256(8), const-256U(9), unavailable-LinkDown(10) |
|
| usrAdslRemoteReqUpConstStatus |
1.3.6.1.4.1.429.4.32.62 |
| Value corresponds to the remote requested downstream constellation requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-auto(1), const-8(2), const-8ER(3), const-16(4), const-32(5), const-64(6), const-128(7), const-256(8), const-256U(9), unavailable-LinkDown(10) |
|
| usrAdslStartletVerson |
1.3.6.1.4.1.429.4.32.63 |
| Value is a number that corresponds to the version number of the STARLET VLSI in the transceiver. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..4 |
|
| usrAdslActualDwnConstStatus |
1.3.6.1.4.1.429.4.32.64 |
| Value corresponds to the actual downstream constellation that was used, which may differ from the value requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-auto(1), const-8(2), const-8ER(3), const-16(4), const-32(5), const-64(6), const-128(7), const-256(8), const-256U(9), unavailable-LinkDown(10) |
|
| usrAdslLocalReqUpConstStatus |
1.3.6.1.4.1.429.4.32.65 |
| Value corresponds to the local upstream constellation requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-8(1), const-16(2), const-32(3), const-64(4), const-128(5), const-256(6), const-256U(7) |
|
| usrAdslRemoteReqDwnConstStatus |
1.3.6.1.4.1.429.4.32.66 |
| Value corresponds to the remote downstream constellation requested. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
const-auto(1), const-8(2), const-8ER(3), const-16(4), const-32(5), const-64(6), const-128(7), const-256(8), const-256U(9), unavailable-LinkDown(10) |
|
| usrAdslLocalReqXmitPower |
1.3.6.1.4.1.429.4.32.69 |
| Transmit power requested at the local ADSL transceiver represented i n dB. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
zero-dB(1), minus3-dB(2), minus6-dB(3), minus9-dB(4), minus12-dB(5), minus15-dB(6) |
|
| usrAdslOverFlowCounter |
1.3.6.1.4.1.429.4.32.73 |
| Running counter for when usrAdslBytesErrorCorrected or usrAdslBytesNotErrorCorrected overflows. This Number is reset to zero each time the Transceiver transitions from Idle Mode to Data Mode. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| usrAdslLastFailedStatus |
1.3.6.1.4.1.429.4.32.74 |
| Defines the last detailed state reached in usrAdslStartupProgress before startup failed. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
no-failure(1), handshake-failure(2), training-failure(3), download-failure(4), invalid-parm(5) |
|
| usrAdslBytesNotErrCorrected |
1.3.6.1.4.1.429.4.32.75 |
| Number of bytes not corrected by Reed-Solomon error correction algorithm in the STARLET.This Number is reset to zero each time the Transceiver transitions from Idle Mode to Data Mode. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| usrAdslOpState |
1.3.6.1.4.1.429.4.32.76 |
| Defines the high level operating state of the transceiver. Used by the customer to determine whether the transceiver is in idle mode or data mode. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
idleMode(1), dataMode(2) |
|
| usrAdslBytesErrCorrected |
1.3.6.1.4.1.429.4.32.77 |
| Number of bytes corrected by Reed-Solomon error correction algorithm in the STARLET.This Number is reset to zero each time the Transceiver transitions from Idle Mode to Data Mode. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|