AIRESPACE-WIRELESS-MIB

File: AIRESPACE-WIRELESS-MIB.mib (526777 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
AIRESPACE-REF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Counter32 Unsigned32
Counter64 Gauge32 IpAddress
TimeTicks NOTIFICATION-GROUP OBJECT-GROUP
MODULE-COMPLIANCE TEXTUAL-CONVENTION DisplayString
RowStatus MacAddress TruthValue
TimeInterval airespace

Defined Objects

bsnWireless 1.3.6.1.4.1.14179.2
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information for 802.11 Access Points, LAN configuration, AAA, Mobility, IpSec, Radio Rescouce Management and 802.11 global parameters. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
MODULE-IDENTITY    

bsnEss 1.3.6.1.4.1.14179.2.1
OBJECT IDENTIFIER    

bsnDot11EssTable 1.3.6.1.4.1.14179.2.1.1
Ess(WLAN) Configuration Table indexed by bsnDot11EssIndex. Maximum of 17 WLANs can be created on Airespace Switch. bsnDot11EssIndex of 17 is reserved for WLAN for Third Party APs(non-Airespace APs).
OBJECT-TYPE    
  SEQUENCE OF  
    BsnDot11EssEntry

bsnDot11EssEntry 1.3.6.1.4.1.14179.2.1.1.1
An entry in bsnDot11EssTable
OBJECT-TYPE    
  BsnDot11EssEntry  

bsnDot11EssIndex 1.3.6.1.4.1.14179.2.1.1.1.1
Index of the Ess(WLAN) within Airespace Switch. Airespace Switch supports 17 ESS(Wlans) so index will be from 1 to 17. 17 is to be used for ESS(WLAN) created for support of Third Party APs(non-Airespace APs)
OBJECT-TYPE    
  Unsigned32 1..17  

bsnDot11EssSsid 1.3.6.1.4.1.14179.2.1.1.1.2
SSID assigned to ESS(WLAN)
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnDot11EssSessionTimeout 1.3.6.1.4.1.14179.2.1.1.1.4
Maximum time of a Mobile Station session. Value of 0 means infinite time(no timeout set).
OBJECT-TYPE    
  Unsigned32 0..86400  

bsnDot11EssMacFiltering 1.3.6.1.4.1.14179.2.1.1.1.5
A type of security policy for Mobile Stations (Clients). Select to filter clients by MAC address. By selecting this Security, you need to create MacFilters in bsnUsersTable or have MacFilters configured on Radius Servers specified in bsnRadiusAuthenticationTable
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssAdminStatus 1.3.6.1.4.1.14179.2.1.1.1.6
Administrative Status of ESS(WLAN). By disabling an ESS the corresponding SSID is no longer broadcasted in AP beacons.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssSecurityAuthType 1.3.6.1.4.1.14179.2.1.1.1.7
Type of 802.11 Authentication.
OBJECT-TYPE    
  INTEGER authOpen(0), authSharedKey(1), authCiscoLeap(128)  

bsnDot11EssStaticWEPSecurity 1.3.6.1.4.1.14179.2.1.1.1.8
Status of Static WEP Security policy. If enabled, WEP Encryption WEP Default Key, Key Index and Key Format should also be specified.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssStaticWEPEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.9
Type of Static WEP Encryption. Length of key specified in Default Key depends on this attribute.
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3)  

bsnDot11EssStaticWEPDefaultKey 1.3.6.1.4.1.14179.2.1.1.1.10
Static WEP Default Key. For wep104 encryption either 26 bit hex key or 13 bit ascii key should be specified. For wep40 encryption 10 bit hex key or 5 bit ascii key should be specified. For wep128 encryption 32 bit hex key or 16 bit ascii key should be specified.
OBJECT-TYPE    
  WEPKeytype  

bsnDot11EssStaticWEPKeyIndex 1.3.6.1.4.1.14179.2.1.1.1.11
According to 802.11 standard 4 keys are supported. So 802.11 Mobile Stations(Client) can have upto 4 keys. This index is for informing Mobile Station which key it should use for Static WEP Authentication
OBJECT-TYPE    
  INTEGER 0..4  

bsnDot11EssStaticWEPKeyFormat 1.3.6.1.4.1.14179.2.1.1.1.12
This is not persistant.Reading this attribute will always return default. The format of the key specified in Airespace switch keeps record of the Index.
OBJECT-TYPE    
  INTEGER hex(1), ascii(2), default(0)  

bsnDot11Ess8021xSecurity 1.3.6.1.4.1.14179.2.1.1.1.13
Status of 802.1X security policy.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11Ess8021xEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.14
Type of 802.1X Encryption. This applies if bsnDot11Ess8021xSecurity is in enabled state.
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3)  

bsnDot11EssWPASecurity 1.3.6.1.4.1.14179.2.1.1.1.16
Status of WPA security policy. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssWPAEncryptionType 1.3.6.1.4.1.14179.2.1.1.1.17
Type of WPA Encryption. This applies when bsnDot11EssWPASecurity is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER wep104(0), wep40(2), wep128(3), tkipmic(5)  

bsnDot11EssIpsecSecurity 1.3.6.1.4.1.14179.2.1.1.1.18
Status of IpSec (VPN) security policy. Note that this cannot be applied with Web security policy.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssVpnEncrTransform 1.3.6.1.4.1.14179.2.1.1.1.19
The Encryption algorithm employed by this Vpn(IpSec) Encryption. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  INTEGER tripleDes(0), none(1), des(2), aesCbc(3)  

bsnDot11EssVpnAuthTransform 1.3.6.1.4.1.14179.2.1.1.1.20
The Hash algorithm employed by the Vpn Encrpytion. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  INTEGER none(1), hmacMd5(2), hmacSha1(0)  

bsnDot11EssVpnIkeAuthMode 1.3.6.1.4.1.14179.2.1.1.1.21
The authentication type of the SA. It could be a certificate or a pre-shared key or xauthEnablePsk. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  INTEGER xauthEnablePsk(0), certificate(2), presharedKey(3)  

bsnDot11EssVpnSharedKey 1.3.6.1.4.1.14179.2.1.1.1.22
VPN Shared Key. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
OBJECT-TYPE    
  OCTET STRING SIZE(1..128)  

bsnDot11EssVpnSharedKeySize 1.3.6.1.4.1.14179.2.1.1.1.23
VPN Shared Key size. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
OBJECT-TYPE    
  Unsigned32 0..128  

bsnDot11EssVpnIkePhase1Mode 1.3.6.1.4.1.14179.2.1.1.1.24
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  INTEGER agressive(0), main(1)  

bsnDot11EssVpnIkeLifetime 1.3.6.1.4.1.14179.2.1.1.1.25
Vpn IKE's Lifetime. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  Integer32 1800..345600  

bsnDot11EssVpnIkeDHGroup 1.3.6.1.4.1.14179.2.1.1.1.26
IKE's Diffie-Hellman Group. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OBJECT-TYPE    
  INTEGER group2(0), group1(1), group5(4)  

bsnDot11EssIpsecPassthruSecurity 1.3.6.1.4.1.14179.2.1.1.1.27
Status of IpSec Passthru security policy.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssVpnPassthruGateway 1.3.6.1.4.1.14179.2.1.1.1.28
Ip address of VpnPassthru Gateway. This applies only when bsnDot11EssIpsecPassthruSecurity is in enable state.
OBJECT-TYPE    
  IpAddress  

bsnDot11EssWebSecurity 1.3.6.1.4.1.14179.2.1.1.1.29
Status of Web security policy. Note this policy cannot be applied with IpSec security policy.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRadioPolicy 1.3.6.1.4.1.14179.2.1.1.1.30
Radio Policy for a WLAN. It can either be All where it will be applicable to ALL types of protocols or it can be set to apply to combinations of 802.11a, 802.11b, 802.11g.
OBJECT-TYPE    
  INTEGER all(0), dot11aOnly(2), dot11bOnly(1), dot11gOnly(3), dot11bgOnly(4), dot11agOnly(5), dot11abOnly(6)  

bsnDot11EssQualityOfService 1.3.6.1.4.1.14179.2.1.1.1.31
Quality of Service for a WLAN.Services such as VoIP should be set to Gold while non-discriminating services such as messaging can be set to Bronze.
OBJECT-TYPE    
  INTEGER bronze(0), silver(1), gold(2), platinum(3)  

bsnDot11EssDhcpRequired 1.3.6.1.4.1.14179.2.1.1.1.32
DHCP required for all clients on this WLAN
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssDhcpServerIpAddress 1.3.6.1.4.1.14179.2.1.1.1.33
IP Address of the DHCP Server. Make it 0.0.0.0 to disable DHCP Relay. Any value other than 0.0.0.0, it will be assumed that DHCP Relay is turned on.
OBJECT-TYPE    
  IpAddress  

bsnDot11EssVpnContivityMode 1.3.6.1.4.1.14179.2.1.1.1.34
Specifies if contivity mode for the IpSec is enabled. If enabled, user needs to specify the Quote of the Day Server's IPAddress in bsnDot11EssVpnQotdServerAddress.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssVpnQotdServerAddress 1.3.6.1.4.1.14179.2.1.1.1.35
IP Address of the Quote of the Day Server.
OBJECT-TYPE    
  IpAddress  

bsnDot11EssBlacklistTimeout 1.3.6.1.4.1.14179.2.1.1.1.37
Set the timeout for blacklisted Mobile Stations after which the mobile station will be automatically de-authenticated. Mobile Station are blacklisted by MAC address and their status can be obtained from bsnMobileStationStatus. A timeout setting of 0 indicates no blacklist timeout is set and administrative control (bsnMobileStationDeleteAction ) is required to deauthenticate the station.
OBJECT-TYPE    
  Integer32 0..2147483647  

bsnDot11EssNumberOfMobileStations 1.3.6.1.4.1.14179.2.1.1.1.38
No of Mobile Stations currently associated with the WLAN.
OBJECT-TYPE    
  Counter32  

bsnDot11EssWebPassthru 1.3.6.1.4.1.14179.2.1.1.1.39
For switches with version before 2.0: This is applicable only when the Web Security Type is enabled. When this attribute is enabled, it allows a client's NetBIOS packets to go through the switch before web auth is completed. (This is obsolete for Switch versions 2.0 to 2.2). For switch verions 3.0 and above: This is reintroduced as the web policy where the client is connected through the web without authentication that is there is no username/password input required. Moreover, if the bsnDot11EssWebPassthroughEmail is enabled, the user will be asked to enter an email address.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssCraniteSecurity 1.3.6.1.4.1.14179.2.1.1.1.40
Status of Cranite Passthrough Security policy. If enabled, no other security can be enabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssBlacklistingCapability 1.3.6.1.4.1.14179.2.1.1.1.41
This is the flag that can enable or disable the client backlisting feature for a WLAN. If enabled, the clients can be blacklisted by the Switch in case of repetitive auth failure and other reasons like it. If disabled, the clients cannot be blacklisted by the switch. The blacklist timeout value will only be effective if this feature is turned on.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssInterfaceName 1.3.6.1.4.1.14179.2.1.1.1.42
Name of the interface used by this WLAN. By default it is set to be the management interface.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnDot11EssAclName 1.3.6.1.4.1.14179.2.1.1.1.43
Name of ACL for the WLAN. This is applicable only when Web Authentication is enabled as a security. An empty string value indicates that no ACL has been set (which is a valid option)
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

bsnDot11EssAAAOverride 1.3.6.1.4.1.14179.2.1.1.1.44
Enable or Disable AAA override for the global WLAN parameters.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssWPAAuthKeyMgmtMode 1.3.6.1.4.1.14179.2.1.1.1.45
Enable or Disable WPA Pre-shared Key Mode. If enabled, a preshared key should be set for WPA authentication. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssWPAAuthPresharedKey 1.3.6.1.4.1.14179.2.1.1.1.46
WPA Authentication Preshared Key. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  OCTET STRING SIZE(8..63)  

bsnDot11EssFortressSecurity 1.3.6.1.4.1.14179.2.1.1.1.47
Status of Fortress Passthrough Security policy. If enabled, no other security can be enabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssWepAllowSharedKeyAuth 1.3.6.1.4.1.14179.2.1.1.1.48
Enable this flag to allow Shared Key Authentication when Static WEP is enabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssL2tpSecurity 1.3.6.1.4.1.14179.2.1.1.1.49
Status of L2TP security policy. Note that this cannot be applied with Web security policy, Cranite or Fortress policy.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssWPAAuthPresharedKeyHex 1.3.6.1.4.1.14179.2.1.1.1.50
WPA Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  OCTET STRING SIZE(0..40)  

bsnDot11EssBroadcastSsid 1.3.6.1.4.1.14179.2.1.1.1.51
This attribute when enabled allows the switch to broadcast this SSID.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssExternalPolicyValidation 1.3.6.1.4.1.14179.2.1.1.1.52
This attribute specifies if external policy servers will be used for validation. If no servers are configured in bsnExternalPolicyServerTable then it cannot be enabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

bsnDot11EssRSNSecurity 1.3.6.1.4.1.14179.2.1.1.1.53
This attribute specifies status of RSN Security Policy. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNWPACompatibilityMode 1.3.6.1.4.1.14179.2.1.1.1.54
This attribute specifies RSN security's compatibility mode with WPA. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNAllowTKIPClients 1.3.6.1.4.1.14179.2.1.1.1.55
This attribute specifies whether TKIP clients are allowed by RSN Policy. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER yes(1), no(0)  

bsnDot11EssRSNAuthKeyMgmtMode 1.3.6.1.4.1.14179.2.1.1.1.56
This attribute specifies whether Preshared key is used or not. If used user should specify a key between 8 and 63 characters in bsnDot11EssRSNAuthPresharedKey attribute. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnDot11EssRSNAuthPresharedKey 1.3.6.1.4.1.14179.2.1.1.1.57
RSN Authentication Preshared Key. This applies only when bsnDot11EssRSNAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  OCTET STRING SIZE(8..63)  

bsnDot11EssRSNAuthPresharedKeyHex 1.3.6.1.4.1.14179.2.1.1.1.58
RSN Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OBJECT-TYPE    
  OCTET STRING SIZE(0..40)  

bsnDot11EssIPv6Bridging 1.3.6.1.4.1.14179.2.1.1.1.59
When enabled, IPv6 bridging is applied on the packets.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11EssRowStatus 1.3.6.1.4.1.14179.2.1.1.1.60
A row status type for the bsnDot11EssEntry
OBJECT-TYPE    
  RowStatus  

bsnDot11EssWmePolicySetting 1.3.6.1.4.1.14179.2.1.1.1.61
When enabled, WME Policy is applied on the packets.
OBJECT-TYPE    
  INTEGER disable(0), allowed(1), required(2), invalid(3)  

bsnDot11Ess80211ePolicySetting 1.3.6.1.4.1.14179.2.1.1.1.62
When enabled, 802.11e Policy is applied on the packets.
OBJECT-TYPE    
  INTEGER disable(0), allowed(1), required(2), invalid(3)  

bsnDot11EssWebPassthroughEmail 1.3.6.1.4.1.14179.2.1.1.1.63
When enabled, along with the bsnDot11EssWebPassthru attribute, the client is allowed to connect by entering his/her email address on the web connection page. There is no further authentication required.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnDot11Ess7920PhoneSupport 1.3.6.1.4.1.14179.2.1.1.1.64
When client cac limit is enabled, the 7920 Phones with old software where the Call Admission Control (CAC) Limit is Specified on the client will be supported on the WLAN. The support for clientCacLimit (by setting to value 1 or 3) cannot be enabled when the bsnDot11EssWmePolicySetting is set to allowed or required. When ap cac limit is enabled, the 7920 Phones with new software where the Call Admission Control (CAC) Limit is advertised by the AP, will be supported on the WLAN.
OBJECT-TYPE    
  INTEGER disable(0), clientCacLimit(1), apCacLimit(2), both(3)  

bsnDot11EssRadiusAuthPrimaryServer 1.3.6.1.4.1.14179.2.1.1.1.95
Primary Radius Authentication Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnDot11EssRadiusAuthSecondaryServer 1.3.6.1.4.1.14179.2.1.1.1.96
Secondary Radius Authentication Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnDot11EssRadiusAuthTertiaryServer 1.3.6.1.4.1.14179.2.1.1.1.97
Tertiary Radius Authentication Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnDot11EssRadiusAcctPrimaryServer 1.3.6.1.4.1.14179.2.1.1.1.98
Primary Radius Accounting Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnDot11EssRadiusAcctSecondaryServer 1.3.6.1.4.1.14179.2.1.1.1.99
Secondary Radius Accounting Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnDot11EssRadiusAcctTertiaryServer 1.3.6.1.4.1.14179.2.1.1.1.100
Tertiary Radius Accounting Server for this wlan.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

bsnMobileStationTable 1.3.6.1.4.1.14179.2.1.4
Mobile Station Table indexed by bsnMobileStationMacAddress. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationEntry

bsnMobileStationEntry 1.3.6.1.4.1.14179.2.1.4.1
An entry in bsnMobileStationTable.
OBJECT-TYPE    
  BsnMobileStationEntry  

bsnMobileStationMacAddress 1.3.6.1.4.1.14179.2.1.4.1.1
802.11 MAC Address of the Mobile Station.
OBJECT-TYPE    
  MacAddress  

bsnMobileStationIpAddress 1.3.6.1.4.1.14179.2.1.4.1.2
IP Address of the Mobile Station
OBJECT-TYPE    
  IpAddress  

bsnMobileStationUserName 1.3.6.1.4.1.14179.2.1.4.1.3
User Name,if any, of the Mobile Station. This would be non empty in case of Web Authentication and IPSec.
OBJECT-TYPE    
  DisplayString  

bsnMobileStationAPMacAddr 1.3.6.1.4.1.14179.2.1.4.1.4
802.11 Mac Address of the AP to which the Mobile Station is associated.
OBJECT-TYPE    
  MacAddress  

bsnMobileStationAPIfSlotId 1.3.6.1.4.1.14179.2.1.4.1.5
Slot ID of AP Interface to which the mobile station is associated. The value 15 is used to indicate that the slot Id is invalid.
OBJECT-TYPE    
  INTEGER 0..15  

bsnMobileStationEssIndex 1.3.6.1.4.1.14179.2.1.4.1.6
Ess Index of the Wlan(SSID) that is being used by Mobile Station to connect to AP
OBJECT-TYPE    
  INTEGER 0..16  

bsnMobileStationSsid 1.3.6.1.4.1.14179.2.1.4.1.7
The SSID Advertised by Mobile Station
OBJECT-TYPE    
  DisplayString  

bsnMobileStationAID 1.3.6.1.4.1.14179.2.1.4.1.8
AID for the mobile station
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationStatus 1.3.6.1.4.1.14179.2.1.4.1.9
Status of the mobile station
OBJECT-TYPE    
  INTEGER idle(0), aaaPending(1), authenticated(2), associated(3), powersave(4), disassociated(5), tobedeleted(6), probing(7), blacklisted(8)  

bsnMobileStationReasonCode 1.3.6.1.4.1.14179.2.1.4.1.10
Reason Code as defined by 802.11 standards
OBJECT-TYPE    
  INTEGER unspecified(1), previousAuthNotValid(2), deauthenticationLeaving(3), disassociationDueToInactivity(4), disassociationAPBusy(5), class2FrameFromNonAuthStation(6), class2FrameFromNonAssStation(7), disassociationStaHasLeft(8), staReqAssociationWithoutAuth(9), missingReasonCode(99)  

bsnMobileStationMobilityStatus 1.3.6.1.4.1.14179.2.1.4.1.11
Mobility Role of the Mobile Station.
OBJECT-TYPE    
  INTEGER unassociated(0), local(1), anchor(2), foreign(3), handoff(4), unknown(5), exportanchor(6), exportforeign(7)  

bsnMobileStationAnchorAddress 1.3.6.1.4.1.14179.2.1.4.1.12
If the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreign
OBJECT-TYPE    
  IpAddress  

bsnMobileStationCFPollable 1.3.6.1.4.1.14179.2.1.4.1.13
When this attribute is true, it shall indicate that the Mobile Station is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the Mobile Station is not able to respond to a CF-Poll with a data frame within a SIFS time.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationCFPollRequest 1.3.6.1.4.1.14179.2.1.4.1.14
Specifies whether CFP is requested by Mobile Station or not
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationChannelAgilityEnabled 1.3.6.1.4.1.14179.2.1.4.1.15
This attribute indicates that the PHY channel agility functionality is enabled.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationPBCCOptionImplemented 1.3.6.1.4.1.14179.2.1.4.1.16
This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationShortPreambleOptionImplemented 1.3.6.1.4.1.14179.2.1.4.1.17
This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnMobileStationSessionTimeout 1.3.6.1.4.1.14179.2.1.4.1.18
Session Timeout of Mobile station
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationAuthenticationAlgorithm 1.3.6.1.4.1.14179.2.1.4.1.19
Authentication Algorithm of Mobile Station
OBJECT-TYPE    
  INTEGER openSystem(0), sharedKey(1), unknown(2), openAndEap(128)  

bsnMobileStationWepState 1.3.6.1.4.1.14179.2.1.4.1.20
WEP State of Mobile Station
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bsnMobileStationPortNumber 1.3.6.1.4.1.14179.2.1.4.1.21
The Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through.
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationDeleteAction 1.3.6.1.4.1.14179.2.1.4.1.22
Action to Deauthenticate the Mobile Station. Set the State to delete.
OBJECT-TYPE    
  INTEGER default(0), delete(1)  

bsnMobileStationPolicyManagerState 1.3.6.1.4.1.14179.2.1.4.1.23
Policy Manager State of the mobile station.
OBJECT-TYPE    
  DisplayString  

bsnMobileStationSecurityPolicyStatus 1.3.6.1.4.1.14179.2.1.4.1.24
When this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be completed.
OBJECT-TYPE    
  INTEGER completed(0), notcompleted(1)  

bsnMobileStationProtocol 1.3.6.1.4.1.14179.2.1.4.1.25
The 802.11 protocol type of the client. The protocol is mobile when this client detail is seen on the anchor i.e it's mobility status is anchor.
OBJECT-TYPE    
  INTEGER dot11a(1), dot11b(2), dot11g(3), unknown(4), mobile(5)  

bsnMobileStationMirrorMode 1.3.6.1.4.1.14179.2.1.4.1.26
If enabled, then mirroring for this client will be statically configured irrespective of the AP and the port this client is on.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMobileStationInterface 1.3.6.1.4.1.14179.2.1.4.1.27
Name of the Interface of the mobile client to the switch.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

bsnMobileStationApMode 1.3.6.1.4.1.14179.2.1.4.1.28
Mode of the AP to which the Mobile Station is associated.
OBJECT-TYPE    
  INTEGER local(0), monitor(1), remote(2), roguedetector(3)  

bsnMobileStationVlanId 1.3.6.1.4.1.14179.2.1.4.1.29
Vlan ID of the Interface to which the client is associated.
OBJECT-TYPE    
  Integer32 0..4096  

bsnMobileStationPolicyType 1.3.6.1.4.1.14179.2.1.4.1.30
Mode of the AP to which the Mobile Station is associated.
OBJECT-TYPE    
  INTEGER dot1x(0), wpa1(1), wpa2(2), wpa2vff(3), notavailable(4), unknown(5)  

bsnMobileStationEncryptionCypher 1.3.6.1.4.1.14179.2.1.4.1.31
Mode of the AP to which the Mobile Station is associated.
OBJECT-TYPE    
  INTEGER ccmpAes(0), tkipMic(1), wep40(2), wep104(3), wep128(4), none(5), notavailable(6), unknown(7)  

bsnMobileStationEapType 1.3.6.1.4.1.14179.2.1.4.1.32
Mode of the AP to which the Mobile Station is associated.
OBJECT-TYPE    
  INTEGER eapTls(0), ttls(1), peap(2), leap(3), speke(4), eapFast(5), notavailable(6), unknown(7)  

bsnMobileStationCcxVersion 1.3.6.1.4.1.14179.2.1.4.1.33
Represents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP.
OBJECT-TYPE    
  INTEGER notSupported(0), ccxv1(1), ccxv2(2), ccxv3(3), ccxv4(4), ccxv5(5)  

bsnMobileStationE2eVersion 1.3.6.1.4.1.14179.2.1.4.1.34
Represents the End-2-End Version the client is using for communication with the AP.
OBJECT-TYPE    
  INTEGER notSupported(0), e2ev1(1), e2ev2(2)  

bsnMobileStationStatusCode 1.3.6.1.4.1.14179.2.1.4.1.42
Status Code of the Mobile Station
OBJECT-TYPE    
  INTEGER 0..65535  

bsnMobileStationPerRadioPerVapTable 1.3.6.1.4.1.14179.2.1.5
Mobile Station Per Radio Per VAP(WLAN) Table. This table lists all Mobile Stations on a particular Airespace AP Interface for a particular ESS(Wlan). It only lists MAC Addresses. Further details for a Mobile Station can be found from bsnMobileStationTable once the MAC Address is knonwn. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationPerRadioPerVapEntry

bsnMobileStationPerRadioPerVapEntry 1.3.6.1.4.1.14179.2.1.5.1
An entry in MobileStationPerRadioPerVapTable.
OBJECT-TYPE    
  BsnMobileStationPerRadioPerVapEntry  

bsnMobileStationPerRadioPerVapIndex 1.3.6.1.4.1.14179.2.1.5.1.1
The index of Mobile Station. The index starts from 1 and goes upto the total number of Mobile Stations on Airespace Radio Interface for a specific ESS (Wlan).
OBJECT-TYPE    
  Integer32  

bsnMobileStationMacAddr 1.3.6.1.4.1.14179.2.1.5.1.20
The MAC Address of Mobile Station.
OBJECT-TYPE    
  MacAddress  

bsnMobileStationStatsTable 1.3.6.1.4.1.14179.2.1.6
Mobile Station Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationStatsEntry

bsnMobileStationStatsEntry 1.3.6.1.4.1.14179.2.1.6.1
An entry in bsnMobileStationStatsTable.
OBJECT-TYPE    
  BsnMobileStationStatsEntry  

bsnMobileStationRSSI 1.3.6.1.4.1.14179.2.1.6.1.1
Average packet RSSI for the Mobile Station.
OBJECT-TYPE    
  Integer32  

bsnMobileStationBytesReceived 1.3.6.1.4.1.14179.2.1.6.1.2
Bytes received from Mobile Station
OBJECT-TYPE    
  Counter64  

bsnMobileStationBytesSent 1.3.6.1.4.1.14179.2.1.6.1.3
Bytes sent to Mobile Station
OBJECT-TYPE    
  Counter64  

bsnMobileStationPolicyErrors 1.3.6.1.4.1.14179.2.1.6.1.4
Number of Policy Errors for Mobile Station
OBJECT-TYPE    
  Counter64  

bsnMobileStationPacketsReceived 1.3.6.1.4.1.14179.2.1.6.1.5
Packets received from Mobile Station
OBJECT-TYPE    
  Counter64  

bsnMobileStationPacketsSent 1.3.6.1.4.1.14179.2.1.6.1.6
Packets sent to Mobile Station
OBJECT-TYPE    
  Counter64  

bsnMobileStationSnr 1.3.6.1.4.1.14179.2.1.6.1.26
Signal to noise Ratio of the Mobile Station.
OBJECT-TYPE    
  Integer32  

bsnRogueAPTable 1.3.6.1.4.1.14179.2.1.7
Rogue Table. This table lists all the Rogue APs detected by Airespace APs.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueAPEntry

bsnRogueAPEntry 1.3.6.1.4.1.14179.2.1.7.1
An Entry in bsnRogueAPTable.
OBJECT-TYPE    
  BsnRogueAPEntry  

bsnRogueAPDot11MacAddress 1.3.6.1.4.1.14179.2.1.7.1.1
MAC Address of Rogue Station.
OBJECT-TYPE    
  MacAddress  

bsnRogueAPTotalDetectingAPs 1.3.6.1.4.1.14179.2.1.7.1.2
Total number of Airespace APs that detected this rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueAPFirstReported 1.3.6.1.4.1.14179.2.1.7.1.3
Time Stamp when this Rogue was First Detected.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPLastReported 1.3.6.1.4.1.14179.2.1.7.1.4
Time Stamp when this Rogue was Last Detected.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPContainmentLevel 1.3.6.1.4.1.14179.2.1.7.1.5
If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
OBJECT-TYPE    
  INTEGER unassigned(0), level1(1), level2(2), level3(3), level4(4)  

bsnRogueAPType 1.3.6.1.4.1.14179.2.1.7.1.6
This attribute specifies if the Rogue is of ad-hoc type or is an AP.
OBJECT-TYPE    
  INTEGER ap(0), adhoc(1)  

bsnRogueAPOnNetwork 1.3.6.1.4.1.14179.2.1.7.1.7
This attribute specifies if the Rogue is on Wired Network or not.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRogueAPTotalClients 1.3.6.1.4.1.14179.2.1.7.1.8
Total number of Clients detected on this rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueAPRowStatus 1.3.6.1.4.1.14179.2.1.7.1.9
Row Status
OBJECT-TYPE    
  RowStatus  

bsnRogueAPMaxDetectedRSSI 1.3.6.1.4.1.14179.2.1.7.1.10
This is the max RSSI value of all the detctecting APs, which have detected this rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueAPSSID 1.3.6.1.4.1.14179.2.1.7.1.11
This is the SSID of the rogue detected by Access Point, which has max RSSI value of all the detectecting APs of this rogue.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnRogueAPState 1.3.6.1.4.1.14179.2.1.7.1.24
This attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP can be a potential threat. Trap will be sent out to trap recipients. Known state means its just internal AP which is not on the same Switch. Acknowledge state means an external AP whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing. Threat is usually the state when the rogue is found on wired network. known(4), knownContained(9) and trustedMissing(10) will appear in known rogue list. known rogues can be pre provisioned and known rogues state can be changed to alert(2)
OBJECT-TYPE    
  INTEGER initializing(0), pending(1), alert(2), detectedLrad(3), known(4), acknowledge(5), contained(6), threat(7), containedPending(8), knownContained(9), trustedMissing(10)  

bsnRogueAPAirespaceAPTable 1.3.6.1.4.1.14179.2.1.8
Rogue Station Table. This table lists all the Airespace AP Interfaces that detected a particular Rogue.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueAPAirespaceAPEntry

bsnRogueAPAirespaceAPEntry 1.3.6.1.4.1.14179.2.1.8.1
An entry in bsnRogueAPAirespaceAPEntry.
OBJECT-TYPE    
  BsnRogueAPAirespaceAPEntry  

bsnRogueAPAirespaceAPMacAddress 1.3.6.1.4.1.14179.2.1.8.1.1
MAC Address of Airespace AP Interface that Detected the Rogue.
OBJECT-TYPE    
  MacAddress  

bsnRogueAPAirespaceAPSlotId 1.3.6.1.4.1.14179.2.1.8.1.2
The slot ID of the Airespace AP Interface that detected the Rogue.
OBJECT-TYPE    
  Unsigned32 0..2  

bsnRogueAPRadioType 1.3.6.1.4.1.14179.2.1.8.1.3
The Airespace AP Interface type that detected the Rogue.
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), unknown(3)  

bsnRogueAPAirespaceAPName 1.3.6.1.4.1.14179.2.1.8.1.4
Name of Airespace AP Interface that detected the Rogue.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPChannelNumber 1.3.6.1.4.1.14179.2.1.8.1.5
The advertised Channel Number of the Airespace AP Interface picked up from the Rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueAPSsid 1.3.6.1.4.1.14179.2.1.8.1.6
The SSID Advertised by Rogue Station.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPAirespaceAPRSSI 1.3.6.1.4.1.14179.2.1.8.1.7
Rogue RSSI as seen by Airespace AP Interface.
OBJECT-TYPE    
  Integer32  

bsnRogueAPContainmentMode 1.3.6.1.4.1.14179.2.1.8.1.8
If the rogue is in 'contained' state, this attribute shows the containment mode used by the AP.
OBJECT-TYPE    
  INTEGER invalid(0), deauthBroadcast(1), cfp(2), max(3), unknown(99)  

bsnRogueAPContainmentChannelCount 1.3.6.1.4.1.14179.2.1.8.1.9
The number of channels used for rogue containment.
OBJECT-TYPE    
  Unsigned32  

bsnRogueAPContainmentChannels 1.3.6.1.4.1.14179.2.1.8.1.10
This is the comma separated string of channels used for rogue containment.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPAirespaceAPLastHeard 1.3.6.1.4.1.14179.2.1.8.1.11
No of seconds ago when this Rogue was last heard by this AP.
OBJECT-TYPE    
  Counter32  

bsnRogueAPAirespaceAPWepMode 1.3.6.1.4.1.14179.2.1.8.1.12
The WEP mode on this detecting AP.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnRogueAPAirespaceAPPreamble 1.3.6.1.4.1.14179.2.1.8.1.13
The Preamble on this detecting AP.
OBJECT-TYPE    
  INTEGER long(0), short(1)  

bsnRogueAPAirespaceAPWpaMode 1.3.6.1.4.1.14179.2.1.8.1.14
The WPA mode on this detecting AP.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnRogueAPAirespaceAPSNR 1.3.6.1.4.1.14179.2.1.8.1.27
SNR seen by Airespace AP Interface from Rogue
OBJECT-TYPE    
  Integer32  

bsnThirdPartyAPTable 1.3.6.1.4.1.14179.2.1.9
Third Party Access Point Table. An entry needs to be configured in this table for a third party access point that needs to be supported by the Switch. Note: A third party ESS (Wlan) with ID 17 should be created in bsnDot11EssTable before adding entries here. Please also note that ACS currently supports only Aironet 350, 1200 and Orinoco 2000 Access Points as third party APs.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnThirdPartyAPEntry

bsnThirdPartyAPEntry 1.3.6.1.4.1.14179.2.1.9.1
An entry in bsnThirdPartyAPTable.
OBJECT-TYPE    
  BsnThirdPartyAPEntry  

bsnThirdPartyAPMacAddress 1.3.6.1.4.1.14179.2.1.9.1.1
MAC Address of Third Party Access Point which is connected directly to this Airespace Switch.
OBJECT-TYPE    
  MacAddress  

bsnThirdPartyAPInterface 1.3.6.1.4.1.14179.2.1.9.1.2
Interface(Port Number) to which the Third Party AP is connected.
OBJECT-TYPE    
  Integer32  

bsnThirdPartyAPIpAddress 1.3.6.1.4.1.14179.2.1.9.1.3
Static IP address of the 3rd Party AP, 0.0.0.0 indicating x its using DHCP
OBJECT-TYPE    
  IpAddress  

bsnThirdPartyAP802Dot1XRequired 1.3.6.1.4.1.14179.2.1.9.1.4
If 802.1X is required for the 3rd Party AP
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnThirdPartyAPMirrorMode 1.3.6.1.4.1.14179.2.1.9.1.5
If enabled, then data from all the foreign AP users and all the foreign APs on this APs port will be mirrored. These clients are dynamically added to the switch's mirrored MAC list.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnThirdPartyAPRowStatus 1.3.6.1.4.1.14179.2.1.9.1.24
Row Status in the ThirdPartyAPEntry.
OBJECT-TYPE    
  RowStatus  

bsnMobileStationByIpTable 1.3.6.1.4.1.14179.2.1.10
Mobile Station Table indexed by bsnMobileStationByIpAddress. NOTE: This is just to facilitate the search of mobile stations based on IP Address. Doing a get without the index doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationByIpEntry

bsnMobileStationByIpEntry 1.3.6.1.4.1.14179.2.1.10.1
An entry in bsnMobileStationByIpTable.
OBJECT-TYPE    
  BsnMobileStationByIpEntry  

bsnMobileStationByIpAddress 1.3.6.1.4.1.14179.2.1.10.1.1
IP Address of the Mobile Station
OBJECT-TYPE    
  IpAddress  

bsnMobileStationByIpMacAddress 1.3.6.1.4.1.14179.2.1.10.1.2
802.11 Mac Address of the Mobile Station.
OBJECT-TYPE    
  MacAddress  

bsnMobileStationRssiDataTable 1.3.6.1.4.1.14179.2.1.11
Mobile Station RSSI data Table indexed by bsnMobileStationMacAddress, bsnMobileStationRssiDataApMacAddress, bsnMobileStationRssiDataApIfSlotId. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationRssiDataEntry

bsnMobileStationRssiDataEntry 1.3.6.1.4.1.14179.2.1.11.1
An entry in bsnMobileStationRssiDataTable.
OBJECT-TYPE    
  BsnMobileStationRssiDataEntry  

bsnMobileStationRssiDataApMacAddress 1.3.6.1.4.1.14179.2.1.11.1.1
802.11 Mac Address of the AP on which Mobile Station is associated.
OBJECT-TYPE    
  MacAddress  

bsnMobileStationRssiDataApIfSlotId 1.3.6.1.4.1.14179.2.1.11.1.2
SlotId of APIf on which mobile station is associated
OBJECT-TYPE    
  Unsigned32 0..15  

bsnMobileStationRssiDataApIfType 1.3.6.1.4.1.14179.2.1.11.1.3
The interface type of the radio that sensed the rssi data.
OBJECT-TYPE    
  INTEGER dot11bg(1), dot11a(2), unknown(3)  

bsnMobileStationRssiDataApName 1.3.6.1.4.1.14179.2.1.11.1.4
The Name of the AP that sensed the rssi data.
OBJECT-TYPE    
  DisplayString  

bsnMobileStationRssiData 1.3.6.1.4.1.14179.2.1.11.1.5
RSSI seen by Airespace AP Interface for the Mobile Station
OBJECT-TYPE    
  Integer32  

bsnAPIfPhyAntennaIndex 1.3.6.1.4.1.14179.2.1.11.1.6
Antenna which recived the probe request from client. The antenna which reported the RSSI value for the client. For now value will be 0 to 1, in future it may change.
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationRssiDataLastHeard 1.3.6.1.4.1.14179.2.1.11.1.25
No of seconds ago when this RSSI data was recorded.
OBJECT-TYPE    
  Counter32  

bsnWatchListClientTable 1.3.6.1.4.1.14179.2.1.12
Table of watch listed clients. When clients are added to this table by username or MAC address, ACS collects data for them to show trend reports. The switch generates Client Association and Client Authentication traps for the watch listed clients.The watch list feature can be enbaled or diabled by the bsnWatchListFeatureEnable flag on the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWatchListClientEntry

bsnWatchListClientEntry 1.3.6.1.4.1.14179.2.1.12.1
An entry in bsnWatchListClientTable.
OBJECT-TYPE    
  BsnWatchListClientEntry  

bsnWatchListClientKey 1.3.6.1.4.1.14179.2.1.12.1.1
MAC Address or User Name of Client that is to be added to the watch list.
OBJECT-TYPE    
  OCTET STRING SIZE(1..64)  

bsnWatchListClientType 1.3.6.1.4.1.14179.2.1.12.1.2
The type of the watch list client entry. The entry can be created by Client MAC Address or by Username.
OBJECT-TYPE    
  INTEGER byMac(1), byUserName(2)  

bsnWatchListClientRowStatus 1.3.6.1.4.1.14179.2.1.12.1.20
A row status type for the bsnWatchListClientEntry
OBJECT-TYPE    
  RowStatus  

bsnMobileStationByUsernameTable 1.3.6.1.4.1.14179.2.1.13
Mobile Station Table indexed by the Mobile Station Username and MAC Address. NOTE: This is just to facilitate the search of mobile stations based on User Name. Doing a get without the username doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationByUsernameEntry

bsnMobileStationByUsernameEntry 1.3.6.1.4.1.14179.2.1.13.1
An entry in bsnMobileStationByUsernameTable.
OBJECT-TYPE    
  BsnMobileStationByUsernameEntry  

bsnMobileStationByUserName 1.3.6.1.4.1.14179.2.1.13.1.1
Username of the Mobile Station
OBJECT-TYPE    
  OCTET STRING SIZE(1..64)  

bsnMobileStationByUserMacAddress 1.3.6.1.4.1.14179.2.1.13.1.2
802.11 Mac Address of the Mobile Station.
OBJECT-TYPE    
  MacAddress  

bsnRogueClientTable 1.3.6.1.4.1.14179.2.1.14
Rogue Client Table. This table lists all the Rogue Clients detected by Airespace APs.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientEntry

bsnRogueClientEntry 1.3.6.1.4.1.14179.2.1.14.1
An Entry in bsnRogueClientTable.
OBJECT-TYPE    
  BsnRogueClientEntry  

bsnRogueClientDot11MacAddress 1.3.6.1.4.1.14179.2.1.14.1.1
Mac Address of Rogue Station.
OBJECT-TYPE    
  MacAddress  

bsnRogueClientTotalDetectingAPs 1.3.6.1.4.1.14179.2.1.14.1.2
Total number of Airespace APs that detected this rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueClientFirstReported 1.3.6.1.4.1.14179.2.1.14.1.3
Time Stamp when this Rogue was First Detected.
OBJECT-TYPE    
  DisplayString  

bsnRogueClientLastReported 1.3.6.1.4.1.14179.2.1.14.1.4
Time Stamp when this Rogue was Last Detected.
OBJECT-TYPE    
  DisplayString  

bsnRogueClientBSSID 1.3.6.1.4.1.14179.2.1.14.1.5
This attribute specifies BSSID of the Rogue Client.
OBJECT-TYPE    
  MacAddress  

bsnRogueClientContainmentLevel 1.3.6.1.4.1.14179.2.1.14.1.6
If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
OBJECT-TYPE    
  INTEGER unassigned(0), level1(1), level2(2), level3(3), level4(4)  

bsnRogueClientLastHeard 1.3.6.1.4.1.14179.2.1.14.1.7
Number of seconds ago this rogue client was detected.
OBJECT-TYPE    
  Integer32  

bsnRogueClientState 1.3.6.1.4.1.14179.2.1.14.1.24
This attribute is use to specify the state in which the Rogue AP is. User can set the Rogue Client in alert,known or acknowledge state. Alert state means Rogue Client can be a potential i threat.Trap will be sent out to trap recipients. Known state means its just internal Client which is not on the same Switch. Acknowledge state means an external Client whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing
OBJECT-TYPE    
  INTEGER initializing(0), pending(1), alert(2), contained(6), threat(7), containedpending(8)  

bsnRogueClientAirespaceAPTable 1.3.6.1.4.1.14179.2.1.15
Rogue Station Table. This table lists all the Airespace AP Interface that detected a particular Rogue.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientAirespaceAPEntry

bsnRogueClientAirespaceAPEntry 1.3.6.1.4.1.14179.2.1.15.1
An entry in bsnRogueClientAirespaceAPEntry.
OBJECT-TYPE    
  BsnRogueClientAirespaceAPEntry  

bsnRogueClientAirespaceAPMacAddress 1.3.6.1.4.1.14179.2.1.15.1.1
Mac Address of Airespace AP Interface that Detected the Rogue.
OBJECT-TYPE    
  MacAddress  

bsnRogueClientAirespaceAPSlotId 1.3.6.1.4.1.14179.2.1.15.1.2
The slotId of the Airespace AP Interface that detected the Rogue.
OBJECT-TYPE    
  Unsigned32 0..2  

bsnRogueClientRadioType 1.3.6.1.4.1.14179.2.1.15.1.3
The advertised SSID that the Airespace AP Interface picked up from the Rogue.
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), unknown(3)  

bsnRogueClientAirespaceAPName 1.3.6.1.4.1.14179.2.1.15.1.4
Name of Airespace AP Interface that detected the Rogue.
OBJECT-TYPE    
  DisplayString  

bsnRogueClientChannelNumber 1.3.6.1.4.1.14179.2.1.15.1.5
The advertised Channel Number of that the Airespace AP Interface picked up from the Rogue.
OBJECT-TYPE    
  Integer32  

bsnRogueClientAirespaceAPRSSI 1.3.6.1.4.1.14179.2.1.15.1.7
RSSI seen by Airespace AP Interface from the Rogue
OBJECT-TYPE    
  Integer32  

bsnRogueClientAirespaceAPLastHeard 1.3.6.1.4.1.14179.2.1.15.1.11
No of seconds ago when this Rogue was last heard by this AP.
OBJECT-TYPE    
  DisplayString  

bsnRogueClientAirespaceAPSNR 1.3.6.1.4.1.14179.2.1.15.1.27
SNR seen by Airespace AP Interface from Rogue
OBJECT-TYPE    
  Integer32  

bsnRogueClientPerRogueAPTable 1.3.6.1.4.1.14179.2.1.16
Rogue Clients for each rogue. This table lists all Rogue Clients on a particular Rogue.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRogueClientPerRogueAPEntry

bsnRogueClientPerRogueAPEntry 1.3.6.1.4.1.14179.2.1.16.1
An entry in RogueClientPerRogueAPTable.
OBJECT-TYPE    
  BsnRogueClientPerRogueAPEntry  

bsnRogueAPDot11MacAddr 1.3.6.1.4.1.14179.2.1.16.1.1
The MAC Address of the Rogue AP.
OBJECT-TYPE    
  MacAddress  

bsnRogueClientDot11MacAddr 1.3.6.1.4.1.14179.2.1.16.1.20
MAC Address of the Rogue Client.
OBJECT-TYPE    
  MacAddress  

bsnDot11QosProfileTable 1.3.6.1.4.1.14179.2.1.17
QOS Profiles specified in bsnDot11EssTable can be customized in this table. This is a lookup table for auto created profiles
OBJECT-TYPE    
  SEQUENCE OF  
    BsnDot11QosProfileEntry

bsnDot11QosProfileEntry 1.3.6.1.4.1.14179.2.1.17.1
An entry in bsnDot11QosProfileTable.
OBJECT-TYPE    
  BsnDot11QosProfileEntry  

bsnDot11QosProfileName 1.3.6.1.4.1.14179.2.1.17.1.1
QOS Profile Name. This will be one of bronze,gold, platinum,silver,uranium.
OBJECT-TYPE    
  OCTET STRING SIZE(1..32)  

bsnDot11QosProfileDesc 1.3.6.1.4.1.14179.2.1.17.1.2
QOS Profile Description.
OBJECT-TYPE    
  OCTET STRING SIZE(1..64)  

bsnDot11QosAverageDataRate 1.3.6.1.4.1.14179.2.1.17.1.3
This is one of the per user bandwidth contracts(k). Specifies Average Data Rate per user. Value of 0 indicates the feature is disabled.
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosBurstDataRate 1.3.6.1.4.1.14179.2.1.17.1.4
This is one of the per user bandwidth contracts(k). Specifies Average Burst Data Rate per user. Value of 0 indicates the feature is disabled.
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosAvgRealTimeDataRate 1.3.6.1.4.1.14179.2.1.17.1.5
This is one of the per user bandwidth contracts(k). Specifies Average Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosBurstRealTimeDataRate 1.3.6.1.4.1.14179.2.1.17.1.6
This is one of the per user bandwidth contracts(k). Specifies Burst Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
OBJECT-TYPE    
  INTEGER 0..60000  

bsnDot11QosMaxRFUsagePerAP 1.3.6.1.4.1.14179.2.1.17.1.7
This is one of the over the Air QOS parameter. Specifies maximum RF Usage per AP in percentage.
OBJECT-TYPE    
  INTEGER 1..100  

bsnDot11QosProfileQueueDepth 1.3.6.1.4.1.14179.2.1.17.1.8
This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
OBJECT-TYPE    
  INTEGER 10..255  

bsnDot11WiredQosProtocol 1.3.6.1.4.1.14179.2.1.17.1.9
This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
OBJECT-TYPE    
  INTEGER none(0), dot1p(1)  

bsnDot11802Dot1PTag 1.3.6.1.4.1.14179.2.1.17.1.10
Specifies the type of wired QOS protocol for the current profile. Value of 0 indicates the feature is disabled.
OBJECT-TYPE    
  INTEGER 0..7  

bsnDot11ResetProfileToDefault 1.3.6.1.4.1.14179.2.1.17.1.40
Set this attribute to reset to restore the factory default value for the profile.
OBJECT-TYPE    
  INTEGER reset(1), default(0)  

bsnTagTable 1.3.6.1.4.1.14179.2.1.18
RF ID Tag Table indexed by bsnTagDot11MacAddress.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagEntry

bsnTagEntry 1.3.6.1.4.1.14179.2.1.18.1
An entry in bsnTagTable.
OBJECT-TYPE    
  BsnTagEntry  

bsnTagDot11MacAddress 1.3.6.1.4.1.14179.2.1.18.1.1
802.11 MAC Address of the RF ID Tag.
OBJECT-TYPE    
  MacAddress  

bsnTagType 1.3.6.1.4.1.14179.2.1.18.1.2
Type of the RF ID Tag.
OBJECT-TYPE    
  INTEGER unknown(0), type1(2)  

bsnTagTimeInterval 1.3.6.1.4.1.14179.2.1.18.1.3
Time Interval after which the tag transmits data.
OBJECT-TYPE    
  Unsigned32  

bsnTagBatteryStatus 1.3.6.1.4.1.14179.2.1.18.1.4
Battery Status of the RF ID Tag.
OBJECT-TYPE    
  INTEGER unknown(0), low(1), normal(2), medium(3)  

bsnTagLastReported 1.3.6.1.4.1.14179.2.1.18.1.23
No of seconds ago when this tag was heard by any AP.
OBJECT-TYPE    
  Unsigned32  

bsnTagRssiDataTable 1.3.6.1.4.1.14179.2.1.19
RF ID Tag Detecting AP Table indexed by bsnTagDot11MacAddress, bsnTagRssiDataApMacAddress and bsnTagRssiDataApIfSlotId.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagRssiDataEntry

bsnTagRssiDataEntry 1.3.6.1.4.1.14179.2.1.19.1
An entry in bsnTagRssiDataTable.
OBJECT-TYPE    
  BsnTagRssiDataEntry  

bsnTagRssiDataApMacAddress 1.3.6.1.4.1.14179.2.1.19.1.1
802.11 MAC Address of the AP detecting the RF ID Tag.
OBJECT-TYPE    
  MacAddress  

bsnTagRssiDataApIfSlotId 1.3.6.1.4.1.14179.2.1.19.1.2
Slot Id of the radio on AP detecting the RF ID Tag.
OBJECT-TYPE    
  Unsigned32 0..5  

bsnTagRssiDataApIfType 1.3.6.1.4.1.14179.2.1.19.1.3
Interface Type of the radio on AP detecting the RF ID Tag.
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), uwb(4)  

bsnTagRssiDataApName 1.3.6.1.4.1.14179.2.1.19.1.4
Name of the AP detecting the RF ID Tag.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

bsnTagRssiDataLastHeard 1.3.6.1.4.1.14179.2.1.19.1.5
No of seconds ago when this tag was heard by this detecting AP.
OBJECT-TYPE    
  Counter32  

bsnTagRssiData 1.3.6.1.4.1.14179.2.1.19.1.6
RSSI of the RF ID Tag as seen by the radio on this detecting AP.
OBJECT-TYPE    
  Integer32  

bsnTagRssiDataSnr 1.3.6.1.4.1.14179.2.1.19.1.26
SNR of the RF ID tag as seen by the radio on this detecting AP.
OBJECT-TYPE    
  Integer32  

bsnTagStatsTable 1.3.6.1.4.1.14179.2.1.20
RF ID Tag Statistics Table.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnTagStatsEntry

bsnTagStatsEntry 1.3.6.1.4.1.14179.2.1.20.1
An entry in bsnTagStatsTable.
OBJECT-TYPE    
  BsnTagStatsEntry  

bsnTagBytesReceived 1.3.6.1.4.1.14179.2.1.20.1.1
Bytes received from an RF ID Tag
OBJECT-TYPE    
  Unsigned32  

bsnTagPacketsReceived 1.3.6.1.4.1.14179.2.1.20.1.20
Packets received from an RF ID Tag
OBJECT-TYPE    
  Unsigned32  

bsnMobileStationExtStatsTable 1.3.6.1.4.1.14179.2.1.21
Mobile Station Extended Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobileStationExtStatsEntry

bsnMobileStationExtStatsEntry 1.3.6.1.4.1.14179.2.1.21.1
An entry in bsnMobileStationExtStatsTable.
OBJECT-TYPE    
  BsnMobileStationExtStatsEntry  

bsnMobileStationSampleTime 1.3.6.1.4.1.14179.2.1.21.1.1
Time stats were sampled as seconds since the epoch.
OBJECT-TYPE    
  Integer32  

bsnMobileStationTxExcessiveRetries 1.3.6.1.4.1.14179.2.1.21.1.2
Tx packets dropped due to excessive retries.
OBJECT-TYPE    
  Counter64  

bsnMobileStationTxRetries 1.3.6.1.4.1.14179.2.1.21.1.3
Tx packets retransmitted.
OBJECT-TYPE    
  Counter64  

bsnMobileStationTxFiltered 1.3.6.1.4.1.14179.2.1.21.1.20
Tx packets dropped by the built-in Tx filter
OBJECT-TYPE    
  Counter64  

bsnAP 1.3.6.1.4.1.14179.2.2
OBJECT IDENTIFIER    

bsnAPTable 1.3.6.1.4.1.14179.2.2.1
Table of Airespace APs managed by this Airespace Switch.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPEntry

bsnAPEntry 1.3.6.1.4.1.14179.2.2.1.1
An entry in the bsnAPTable.
OBJECT-TYPE    
  BsnAPEntry  

bsnAPDot3MacAddress 1.3.6.1.4.1.14179.2.2.1.1.1
The MAC address of an AP.
OBJECT-TYPE    
  MacAddress  

bsnAPNumOfSlots 1.3.6.1.4.1.14179.2.2.1.1.2
Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g.
OBJECT-TYPE    
  INTEGER 0..24  

bsnAPName 1.3.6.1.4.1.14179.2.2.1.1.3
Name assigned to this AP. If an AP is not configured its factory default name will be ap: eg. ap:af:12:be
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnAPLocation 1.3.6.1.4.1.14179.2.2.1.1.4
User specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located.
OBJECT-TYPE    
  OCTET STRING SIZE(0..80)  

bsnAPMonitorOnlyMode 1.3.6.1.4.1.14179.2.2.1.1.5
Monitor Only Mode Setting.
OBJECT-TYPE    
  INTEGER local(0), monitor(1), remote(2), roguedetector(3), sniffer(4), bridge(5)  

bsnAPOperationStatus 1.3.6.1.4.1.14179.2.2.1.1.6
Operation State of the AP. When AP associates with the Airespace Switch its state will be associated. When Airespace AP is disassociated from the Switch, its state will be disassociating. The state is downloading when the AP is downloading its firmware.
OBJECT-TYPE    
  INTEGER associated(1), disassociating(2), downloading(3)  

bsnAPSoftwareVersion 1.3.6.1.4.1.14179.2.2.1.1.8
Major Minor Software Version of AP
OBJECT-TYPE    
  DisplayString  

bsnAPBootVersion 1.3.6.1.4.1.14179.2.2.1.1.9
Major Minor Boot Version of AP
OBJECT-TYPE    
  DisplayString  

bsnAPPrimaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.10
sysName of the Airespace Switch which is suppose to be the Primary MWAR(switch) of the AP with which AP should associate. This work when AP is not directly connected to Airespace Switch, it tries to find Primary Switch and associates with it. If this attribute is left empty or AP is not able to find the Airespace Switch with this name, then it will associate with Secondary Switch.
OBJECT-TYPE    
  OCTET STRING SIZE(0..31)  

bsnAPReset 1.3.6.1.4.1.14179.2.2.1.1.11
Set this attribute to reset the AP. When it comes up it will try to associate with the Primary Switch if that is set, else it will associate with the Master Switch. Reading this attribute will always return 0
OBJECT-TYPE    
  INTEGER reset(1), default(0)  

bsnAPStatsTimer 1.3.6.1.4.1.14179.2.2.1.1.12
Configures the time interval in secs after which bsnAPDot11Counters Stats is sent from AP to Switch. If not configured this value is 0 which means never send the stats.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPPortNumber 1.3.6.1.4.1.14179.2.2.1.1.13
Port on the Switch on which this APs traffic is coming through.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPModel 1.3.6.1.4.1.14179.2.2.1.1.16
AP Model
OBJECT-TYPE    
  DisplayString  

bsnAPSerialNumber 1.3.6.1.4.1.14179.2.2.1.1.17
AP Serial Number.
OBJECT-TYPE    
  DisplayString  

bsnAPClearConfig 1.3.6.1.4.1.14179.2.2.1.1.18
Set this attribute to clear AP configuration and reset it to factory defaults. Reading this attribute will always return 0
OBJECT-TYPE    
  INTEGER clear(1), default(0)  

bsnApIpAddress 1.3.6.1.4.1.14179.2.2.1.1.19
IP address of the AP. This will not be available when the switch is operating in the Layer2 mode. In this case, the attribute will return 0 as value.
OBJECT-TYPE    
  IpAddress  

bsnAPMirrorMode 1.3.6.1.4.1.14179.2.2.1.1.20
If enabled, then this AP's Client's Data is mirrored and this AP's clients are dynamically added to the switch's mirrored MAC list.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPRemoteModeSupport 1.3.6.1.4.1.14179.2.2.1.1.21
This specifies if the the Remote Mode is supported on this AP or not. If supported user can set bsnAPMonitorOnlyMode to remote. Otherwise not.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPType 1.3.6.1.4.1.14179.2.2.1.1.22
This is the model of the AP in enumeration.
OBJECT-TYPE    
  INTEGER ap1000(1), ap1030(2), mimo(3), unknown(4), ap1100(5), ap1130(6), ap1240(7), ap1200(8), ap1310(9), ap1500(10), ap1250(11), ap1505(12)  

bsnAPSecondaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.23
sysName of the Airespace Switch which is suppose to be the Secondary MWAR(switch) of the AP with which AP should associate if Primary Switch(configured through bsnAPPrimaryMwarName) is not available. If primary and secondary switches are not available then AP will associate with the tertiary switch.
OBJECT-TYPE    
  OCTET STRING SIZE(0..31)  

bsnAPTertiaryMwarName 1.3.6.1.4.1.14179.2.2.1.1.24
sysName of the Airespace Switch which is suppose to be the Tertiary MWAR(switch) of the AP with which AP should associate. If primary,secondary and tertiary switch are not available then it will associate with Master Switch.
OBJECT-TYPE    
  OCTET STRING SIZE(0..31)  

bsnAPIsStaticIP 1.3.6.1.4.1.14179.2.2.1.1.25
This flag when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gateway.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNetmask 1.3.6.1.4.1.14179.2.2.1.1.26
The Netmask of the IP address of the AP.
OBJECT-TYPE    
  IpAddress  

bsnAPGateway 1.3.6.1.4.1.14179.2.2.1.1.27
The Gateway for the AP.
OBJECT-TYPE    
  IpAddress  

bsnAPStaticIPAddress 1.3.6.1.4.1.14179.2.2.1.1.28
The Static IP-Address configuration for the AP. This can only be changed when the LWAPP mode is in Layer-3.
OBJECT-TYPE    
  IpAddress  

bsnAPBridgingSupport 1.3.6.1.4.1.14179.2.2.1.1.29
This specifies if this AP is a Bridging AP. Bridging APs can be used in Bridging or Mesh network configurations.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPGroupVlanName 1.3.6.1.4.1.14179.2.2.1.1.30
The AP Group to which this AP has been associated with. If it is empty, then no AP Group overriding has been set.
OBJECT-TYPE    
  OCTET STRING SIZE(0..31)  

bsnAPIOSVersion 1.3.6.1.4.1.14179.2.2.1.1.31
IOS Version of IOS Cisco AP. Zero length string will be returned for other APs
OBJECT-TYPE    
  DisplayString  

bsnAPCertificateType 1.3.6.1.4.1.14179.2.2.1.1.32
Enum values denoting AP Certificate Type. 1 : manufactureinstalled : Manufacture Installed Certificate type (MIC). 2 : selfsigned : Self Signed Certificate type (SSC). 3 : localsignificance : Local Significance.
OBJECT-TYPE    
  INTEGER unknown(0), manufactureinstalled(1), selfsigned(2), localsignificance(3)  

bsnAPEthernetMacAddress 1.3.6.1.4.1.14179.2.2.1.1.33
The Ethernet MAC address of the AP.
OBJECT-TYPE    
  MacAddress  

bsnAPAdminStatus 1.3.6.1.4.1.14179.2.2.1.1.37
Admin State of the AP
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bsnAPIfTable 1.3.6.1.4.1.14179.2.2.2
Each entry represents an 802.11 interface in an Airespace AP.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfEntry

bsnAPIfEntry 1.3.6.1.4.1.14179.2.2.2.1
An entry in bsnAPIfTable.
OBJECT-TYPE    
  BsnAPIfEntry  

bsnAPIfSlotId 1.3.6.1.4.1.14179.2.2.2.1.1
The slotId of this interface.
OBJECT-TYPE    
  Unsigned32 0..2  

bsnAPIfType 1.3.6.1.4.1.14179.2.2.2.1.2
The type of this interface. dot11b also implies 802.11b/g.
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2), uwb(4)  

bsnAPIfPhyChannelAssignment 1.3.6.1.4.1.14179.2.2.2.1.3
If this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only.
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfPhyChannelNumber 1.3.6.1.4.1.14179.2.2.2.1.4
Current channel number of the AP Interface. Channel numbers will be from 1 to 14 for 802.11b interface type. Channel numbers will be from 34 to 169 for 802.11a interface type. Allowed channel numbers also depends on the current Country Code set in the Switch. This attribute cannot be set unless bsnAPIfPhyChannelAssignment is set to customized else this attribute gets assigned by dynamic algorithm.
OBJECT-TYPE    
  INTEGER ch1(1), ch2(2), ch3(3), ch4(4), ch5(5), ch6(6), ch7(7), ch8(8), ch9(9), ch10(10), ch11(11), ch12(12), ch13(13), ch14(14), ch34(34), ch36(36), ch38(38), ch40(40), ch42(42), ch44(44), ch46(46), ch48(48), ch52(52), ch56(56), ch60(60), ch64(64), ch100(100), ch104(104), ch108(108), ch112(112), ch116(116), ch120(120), ch124(124), ch128(128), ch132(132), ch136(136), ch140(140), ch149(149), ch153(153), ch157(157), ch161(161), ch165(165), ch169(169)  

bsnAPIfPhyTxPowerControl 1.3.6.1.4.1.14179.2.2.2.1.5
If this value is true, then bsnAPIfPhyTxPowerLevel is assigned by dynamic algorithm and is read-only.
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfPhyTxPowerLevel 1.3.6.1.4.1.14179.2.2.2.1.6
The TxPowerLevel currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. Valid values are between 1 to 8,depnding on what radio, and this attribute can be set only if bsnAPIfPhyTxPowerControl is set to customized.
OBJECT-TYPE    
  INTEGER 1..8  

bsnAPIfPhyAntennaMode 1.3.6.1.4.1.14179.2.2.2.1.7
Antenna Mode of the AP Interface. For 802.11a this attribute will always be omni for now. This attribute doesn't apply to interface of type 802.11b.
OBJECT-TYPE    
  INTEGER sectorA(1), sectorB(2), omni(3), notapplicable(99)  

bsnAPIfPhyAntennaType 1.3.6.1.4.1.14179.2.2.2.1.8
This attribute specified if the Antenna currently used by AP Radio is internal or external. For 802.11a the antenna is always internal. For 802.11b you can set antenna type to be external or internal.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

bsnAPIfPhyAntennaDiversity 1.3.6.1.4.1.14179.2.2.2.1.9
Diversity doesn't apply to AP Radio of type 802.11a. For 802.11b you can set it to connectorA, connectorB or enabled.
OBJECT-TYPE    
  INTEGER connectorA(0), connectorB(1), enabled(255)  

bsnAPIfCellSiteConfigId 1.3.6.1.4.1.14179.2.2.2.1.10
In a cell site configuration, this would be the cell Id of this AP Interface
OBJECT-TYPE    
  Unsigned32  

bsnAPIfNumberOfVaps 1.3.6.1.4.1.14179.2.2.2.1.11
Number of WLANs currently active on this AP Interface.
OBJECT-TYPE    
  INTEGER 1..16  

bsnAPIfOperStatus 1.3.6.1.4.1.14179.2.2.2.1.12
Operational status of the interface.
OBJECT-TYPE    
  INTEGER down(1), up(2)  

bsnAPIfPortNumber 1.3.6.1.4.1.14179.2.2.2.1.13
Port number on Airespace Switch on which the traffic from this AP interface is received.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPIfPhyAntennaOptions 1.3.6.1.4.1.14179.2.2.2.1.14
This attribute specifies the Antenna types supported by the AP Radio whether it is internal or external or both. internalAndExternal(0)- internal and external antenna for both 11a and 11b internal(1) - only internal antenna is allowed. siacAp- 11b internal and 11a external external - only external antenna is allowed for 11a and 11b ext11bInt11a - external antenna for 11b and internal antenna for 11a.
OBJECT-TYPE    
  INTEGER internalAndExternal(0), internal(1), siacAp(2), external(3), ext11bInt11a(4)  

bsnApIfNoOfUsers 1.3.6.1.4.1.14179.2.2.2.1.15
No of Users associated with this radio.
OBJECT-TYPE    
  Counter32  

bsnAPIfWlanOverride 1.3.6.1.4.1.14179.2.2.2.1.16
This flag when disabled implies that all WLANs are available from this radio. However, if this is enabled, then only those WLANs that appear in the bsnApIfWlanOverrideTable will be available from this radio.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPIfPacketsSniffingFeature 1.3.6.1.4.1.14179.2.2.2.1.17
This flag when enabled implies that AP will sniff the 802.11a/bg packets. However, if it is enabled, then user should enter the server-ip-address on which Airopeek is running and the 802.11a/bg-channel-number to be sniffed. The above feature will work only when AP is in 'Sniffer' mode.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPIfSniffChannel 1.3.6.1.4.1.14179.2.2.2.1.18
This the 802.11a/bg-channel-number on which AP will sniff the packets.
OBJECT-TYPE    
  INTEGER ch0(0), ch1(1), ch2(2), ch3(3), ch4(4), ch5(5), ch6(6), ch7(7), ch8(8), ch9(9), ch10(10), ch11(11), ch12(12), ch13(13), ch14(14), ch34(34), ch36(36), ch38(38), ch40(40), ch42(42), ch44(44), ch46(46), ch48(48), ch52(52), ch56(56), ch60(60), ch64(64), ch100(100), ch104(104), ch108(108), ch112(112), ch116(116), ch120(120), ch124(124), ch128(128), ch132(132), ch136(136), ch140(140), ch149(149), ch153(153), ch157(157), ch161(161), ch165(165), ch169(169)  

bsnAPIfSniffServerIPAddress 1.3.6.1.4.1.14179.2.2.2.1.19
The machine ip address on which Airopeek application is running.
OBJECT-TYPE    
  IpAddress  

bsnAPIfAntennaGain 1.3.6.1.4.1.14179.2.2.2.1.20
Represents antenna gain in multiple of 0.5 dBm. An interger value 4 means 4 x 0.5 = 2 dBm of gain
OBJECT-TYPE    
  INTEGER 0..40  

bsnAPIfChannelList 1.3.6.1.4.1.14179.2.2.2.1.21
List of comma separated channels supported by this radio.
OBJECT-TYPE    
  DisplayString  

bsnAPIfAbsolutePowerList 1.3.6.1.4.1.14179.2.2.2.1.22
List of comma separated absolute power levels supported by this radio.
OBJECT-TYPE    
  DisplayString  

bsnAPIfRegulatoryDomainSupport 1.3.6.1.4.1.14179.2.2.2.1.23
If the regulatory domain on radio is supported or notSupported on the controller
OBJECT-TYPE    
  INTEGER notSupported(0), supported(1)  

bsnAPIfAdminStatus 1.3.6.1.4.1.14179.2.2.2.1.34
Admin status of the interface.
OBJECT-TYPE    
  INTEGER disable(2), enable(1)  

bsnAPIfSmtParamTable 1.3.6.1.4.1.14179.2.2.3
Each entry represents SMT parameters on an 802.11 interface of an Airespace AP.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfSmtParamEntry

bsnAPIfSmtParamEntry 1.3.6.1.4.1.14179.2.2.3.1
An entry in bsnAPIfSmtParamTable
OBJECT-TYPE    
  BsnAPIfSmtParamEntry  

bsnAPIfDot11BeaconPeriod 1.3.6.1.4.1.14179.2.2.3.1.1
This attribute shall specify the number of TU that a AP Interface shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
OBJECT-TYPE    
  INTEGER 20..1000  

bsnAPIfDot11MediumOccupancyLimit 1.3.6.1.4.1.14179.2.2.3.1.2
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
OBJECT-TYPE    
  INTEGER 0..1000  

bsnAPIfDot11CFPPeriod 1.3.6.1.4.1.14179.2.2.3.1.3
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..255  

bsnAPIfDot11CFPMaxDuration 1.3.6.1.4.1.14179.2.2.3.1.4
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnAPIfDot11OperationalRateSet 1.3.6.1.4.1.14179.2.2.3.1.5
This attribute shall specify the set of data rates at which the AP Interface may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the AP Interface desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3.
OBJECT-TYPE    
  OCTET STRING SIZE(1..126)  

bsnAPIfDot11DTIMPeriod 1.3.6.1.4.1.14179.2.2.3.1.6
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MultiDomainCapabilityImplemented 1.3.6.1.4.1.14179.2.2.3.1.7
This attribute, when TRUE, indicates that the AP Interface implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnAPIfDot11MultiDomainCapabilityEnabled 1.3.6.1.4.1.14179.2.2.3.1.8
This attribute, when TRUE, indicates that the capability of the AP Interface to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnAPIfDot11CountryString 1.3.6.1.4.1.14179.2.2.3.1.9
This attribute identifies the country in which the AP Interface is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of the following: 1. an ASCII space character, if the regulations under which the AP Interface is operating encompass all environments in the country, 2. an ASCII 'O' character, if the regulations under which the AP Interface is operating are for an Outdoor environment only, or 3. an ASCII 'I' character, if the regulations under which the AP Interface is operating are for an Indoor environment only.
OBJECT-TYPE    
  OCTET STRING SIZE(3)  

bsnAPIfDot11SmtParamsConfigType 1.3.6.1.4.1.14179.2.2.3.1.10
This attribute suggests if the Station parameters for this radio are automatically set or have been customized.
OBJECT-TYPE    
  INTEGER automatic(0), customized(1)  

bsnAPIfDot11BSSID 1.3.6.1.4.1.14179.2.2.3.1.30
BSSID of this AP config which would be the MAC Address of AP
OBJECT-TYPE    
  MacAddress  

bsnAPIfMultiDomainCapabilityTable 1.3.6.1.4.1.14179.2.2.4
Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfMultiDomainCapabilityEntry

bsnAPIfMultiDomainCapabilityEntry 1.3.6.1.4.1.14179.2.2.4.1
Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
OBJECT-TYPE    
  BsnAPIfMultiDomainCapabilityEntry  

bsnAPIfDot11MaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.2.4.1.1
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11FirstChannelNumber 1.3.6.1.4.1.14179.2.2.4.1.2
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11NumberofChannels 1.3.6.1.4.1.14179.2.2.4.1.20
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnAPIfMacOperationParamTable 1.3.6.1.4.1.14179.2.2.5
Group contains MAC attributes pertaining to the operation of the MAC. These would be read only attributes as they would be updated by RRM Dynamic Algorithm. If user needs to configure them then they can only be configured globally
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfMacOperationParamEntry

bsnAPIfMacOperationParamEntry 1.3.6.1.4.1.14179.2.2.5.1
An entry in the bsnAPIfMacOperationParamEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
OBJECT-TYPE    
  BsnAPIfMacOperationParamEntry  

bsnAPIfDot11MacRTSThreshold 1.3.6.1.4.1.14179.2.2.5.1.1
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  INTEGER 0..2347  

bsnAPIfDot11MacShortRetryLimit 1.3.6.1.4.1.14179.2.2.5.1.2
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MacLongRetryLimit 1.3.6.1.4.1.14179.2.2.5.1.3
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  INTEGER 1..255  

bsnAPIfDot11MacFragmentationThreshold 1.3.6.1.4.1.14179.2.2.5.1.4
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  INTEGER 256..2346  

bsnAPIfDot11MacMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.2.5.1.5
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnAPIfDot11MacParamsConfigType 1.3.6.1.4.1.14179.2.2.5.1.6
This attribute suggests if the MAC parameters for this radio are automatically set or have been customized.
OBJECT-TYPE    
  INTEGER automatic(0), customized(1)  

bsnAPIfDot11MacMaxReceiveLifetime 1.3.6.1.4.1.14179.2.2.5.1.25
If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnAPIfDot11CountersTable 1.3.6.1.4.1.14179.2.2.6
Group containing attributes that are MAC counters. Each instance represents counters on a AP dot11 interface
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11CountersEntry

bsnAPIfDot11CountersEntry 1.3.6.1.4.1.14179.2.2.6.1
An entry in the dot11CountersEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfDot11CountersEntry  

bsnAPIfDot11TransmittedFragmentCount 1.3.6.1.4.1.14179.2.2.6.1.1
This counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MulticastTransmittedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.2
This counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RetryCount 1.3.6.1.4.1.14179.2.2.6.1.3
This counter shall increment when an MSDU is successfully transmitted after one or more retransmissions.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MultipleRetryCount 1.3.6.1.4.1.14179.2.2.6.1.4
This counter shall increment when an MSDU is successfully transmitted after more than one retransmission.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FrameDuplicateCount 1.3.6.1.4.1.14179.2.2.6.1.5
This counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RTSSuccessCount 1.3.6.1.4.1.14179.2.2.6.1.6
This counter shall increment when a CTS is received in response to an RTS.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11RTSFailureCount 1.3.6.1.4.1.14179.2.2.6.1.7
This counter shall increment when a CTS is not received in response to an RTS.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11ACKFailureCount 1.3.6.1.4.1.14179.2.2.6.1.8
This counter shall increment when an ACK is not received when expected.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11ReceivedFragmentCount 1.3.6.1.4.1.14179.2.2.6.1.9
This counter shall be incremented for each successfully received MPDU of type Data or Management.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11MulticastReceivedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.10
This counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FCSErrorCount 1.3.6.1.4.1.14179.2.2.6.1.11
This counter shall increment when an FCS error is detected in a received MPDU.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11TransmittedFrameCount 1.3.6.1.4.1.14179.2.2.6.1.12
This counter shall increment for each successfully transmitted MSDU.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11WEPUndecryptableCount 1.3.6.1.4.1.14179.2.2.6.1.13
This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the TA's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11FailedCount 1.3.6.1.4.1.14179.2.2.6.1.33
This counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the bsnAPIfDot11ShortRetryLimit or dot11LongRetryLimit.
OBJECT-TYPE    
  Counter32  

bsnAPIfDot11PhyTxPowerTable 1.3.6.1.4.1.14179.2.2.8
Group of attributes for bsnAPIfDot11PhyTxPowerTable. Implemented as a table indexed on STA ID to allow for multiple instances on an Agent. This table has been deprecated. The level and power can be obtained from bsnAPIfTable(bsnAPIfAbsolutePowerList).
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11PhyTxPowerEntry

bsnAPIfDot11PhyTxPowerEntry 1.3.6.1.4.1.14179.2.2.8.1
An entry in the bsnAPIfDot11PhyTxPower Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
OBJECT-TYPE    
  BsnAPIfDot11PhyTxPowerEntry  

bsnAPIfDot11NumberSupportedPowerLevels 1.3.6.1.4.1.14179.2.2.8.1.1
The number of power levels supported by the PMD. This attribute can have a value of 1 to 8.
OBJECT-TYPE    
  INTEGER 1..8  

bsnAPIfDot11TxPowerLevel1 1.3.6.1.4.1.14179.2.2.8.1.2
The transmit output power for LEVEL1 in mW. This is also the default power level. It is same as the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel2 1.3.6.1.4.1.14179.2.2.8.1.3
The transmit output power for LEVEL2 in mW. It is 1/2 of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel3 1.3.6.1.4.1.14179.2.2.8.1.4
The transmit output power for LEVEL3 in mW. It is 1/4th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel4 1.3.6.1.4.1.14179.2.2.8.1.5
The transmit output power for LEVEL4 in mW. It is 1/8th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel5 1.3.6.1.4.1.14179.2.2.8.1.6
The transmit output power for LEVEL5 in mW. It is 1/16th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel6 1.3.6.1.4.1.14179.2.2.8.1.7
The transmit output power for LEVEL6 in mW. It is 1/32th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel7 1.3.6.1.4.1.14179.2.2.8.1.8
The transmit output power for LEVEL7 in mW. It is 1/64th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11TxPowerLevel8 1.3.6.1.4.1.14179.2.2.8.1.28
The transmit output power for LEVEL8 in mW. It is 1/128th of the Maximum power level available on an AP interface.
OBJECT-TYPE    
  INTEGER 0..10000  

bsnAPIfDot11PhyChannelTable 1.3.6.1.4.1.14179.2.2.9
Entry of attributes for bsnAPIfDot11PhyChannelEntry. Implemented as a table indexed on bsnAPDot3MacAddress, bsnAPIfSlotId allow for multiple instances on an Agent
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfDot11PhyChannelEntry

bsnAPIfDot11PhyChannelEntry 1.3.6.1.4.1.14179.2.2.9.1
An entry in the bsnAPIfDot11PhyChannelEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
OBJECT-TYPE    
  BsnAPIfDot11PhyChannelEntry  

bsnAPIfDot11CurrentCCAMode 1.3.6.1.4.1.14179.2.2.9.1.1
The current CCA method in operation.Valid values are: energy detect only (edonly) = 01, carrier sense only (csonly) = 02, carrier sense and energy detect (edandcs)= 04 carrier sense with timer (cswithtimer)= 08 high rate carrier sense and energy detect (hrcsanded)=16.
OBJECT-TYPE    
  INTEGER edonly(1), csonly(2), edandcs(4), cswithtimer(8), hrcsanded(16)  

bsnAPIfDot11EDThreshold 1.3.6.1.4.1.14179.2.2.9.1.2
The current Energy Detect Threshold being used by the Channel PHY.
OBJECT-TYPE    
  Integer32  

bsnAPIfDot11TIThreshold 1.3.6.1.4.1.14179.2.2.9.1.23
The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
OBJECT-TYPE    
  Integer32  

bsnAPIfProfileThresholdConfigTable 1.3.6.1.4.1.14179.2.2.12
Table of attributes for various thresholds to be set on each Airespace AP Interface for Load performance profile , interference performance profile and Noise performance profile.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfProfileThresholdConfigEntry

bsnAPIfProfileThresholdConfigEntry 1.3.6.1.4.1.14179.2.2.12.1
An entry (conceptual row) in the Phy Thresholds Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfProfileThresholdConfigEntry  

bsnAPIfProfileParamAssignment 1.3.6.1.4.1.14179.2.2.12.1.1
If this value is automatic then Profile Parameters in bsnRrmDot11aAPProfile at the global level will be used. If this value is customized then Profile Parameters in bsnAPIfProfileThresholdConfig Table will be used and user can customize them per AP.
OBJECT-TYPE    
  INTEGER automatic(1), customized(2)  

bsnAPIfForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.2.12.1.2
foreign interference threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfForeignNoiseThreshold 1.3.6.1.4.1.14179.2.2.12.1.3
foreign noise threshold between -100 and -50 dBm.
OBJECT-TYPE    
  INTEGER -127..0  

bsnAPIfRFUtilizationThreshold 1.3.6.1.4.1.14179.2.2.12.1.4
RF utlization threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfThroughputThreshold 1.3.6.1.4.1.14179.2.2.12.1.5
Airespace AP data-rate threshold between 1000 and 100000
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnAPIfMobilesThreshold 1.3.6.1.4.1.14179.2.2.12.1.6
Airespace AP mobiles threshold between 1 and 75
OBJECT-TYPE    
  INTEGER 1..75  

bsnAPIfCoverageThreshold 1.3.6.1.4.1.14179.2.2.12.1.7
Airespace AP coverage threshold between 3 and 50
OBJECT-TYPE    
  INTEGER 3..50  

bsnAPIfMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.2.12.1.8
Airespace AP mobile minimum exception level between 1 and 1000
OBJECT-TYPE    
  INTEGER 1..75  

bsnAPIfCoverageExceptionLevel 1.3.6.1.4.1.14179.2.2.12.1.28
Airespace AP coverage exception level between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadParametersTable 1.3.6.1.4.1.14179.2.2.13
These are RRM performance related read only parameters per Airespace AP
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfLoadParametersEntry

bsnAPIfLoadParametersEntry 1.3.6.1.4.1.14179.2.2.13.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfLoadParametersEntry  

bsnAPIfLoadRxUtilization 1.3.6.1.4.1.14179.2.2.13.1.1
This is the percentage of time the Airespace AP receiver is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadTxUtilization 1.3.6.1.4.1.14179.2.2.13.1.2
This is the percentage of time the Airespace AP transmitter is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadChannelUtilization 1.3.6.1.4.1.14179.2.2.13.1.3
Channel Utilization
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfLoadNumOfClients 1.3.6.1.4.1.14179.2.2.13.1.4
This is the number of clients attached to this Airespace AP at the last measurement interval(This comes from APF)
OBJECT-TYPE    
  Integer32  

bsnAPIfPoorSNRClients 1.3.6.1.4.1.14179.2.2.13.1.24
This is the number of clients with poor SNR attached to this Airespace AP at the last measurement interval ( This comes from APF ).
OBJECT-TYPE    
  Integer32  

bsnAPIfChannelInterferenceInfoTable 1.3.6.1.4.1.14179.2.2.14
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfChannelInterferenceInfoEntry

bsnAPIfChannelInterferenceInfoEntry 1.3.6.1.4.1.14179.2.2.14.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfChannelInterferenceInfoEntry  

bsnAPIfInterferenceChannelNo 1.3.6.1.4.1.14179.2.2.14.1.1
Channel Number on AP
OBJECT-TYPE    
  Integer32  

bsnAPIfInterferencePower 1.3.6.1.4.1.14179.2.2.14.1.2
Power of Interference from other 802.11 networks on this channel
OBJECT-TYPE    
  Integer32  

bsnAPIfInterferenceUtilization 1.3.6.1.4.1.14179.2.2.14.1.22
Interference from other 802.11 networks on this channel
OBJECT-TYPE    
  INTEGER 0..100  

bsnAPIfChannelNoiseInfoTable 1.3.6.1.4.1.14179.2.2.15
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfChannelNoiseInfoEntry

bsnAPIfChannelNoiseInfoEntry 1.3.6.1.4.1.14179.2.2.15.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfChannelNoiseInfoEntry  

bsnAPIfNoiseChannelNo 1.3.6.1.4.1.14179.2.2.15.1.1
Channel Number on AP
OBJECT-TYPE    
  Integer32  

bsnAPIfDBNoisePower 1.3.6.1.4.1.14179.2.2.15.1.21
This is the average noise power in dBm on each channel that is available to Airespace AP
OBJECT-TYPE    
  Integer32  

bsnAPIfProfileStateTable 1.3.6.1.4.1.14179.2.2.16
This is a table of state of interference monitor on each Airespace AP
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfProfileStateEntry

bsnAPIfProfileStateEntry 1.3.6.1.4.1.14179.2.2.16.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfProfileStateEntry  

bsnAPIfLoadProfileState 1.3.6.1.4.1.14179.2.2.16.1.1
This field represents the current state of the LOAD monitor. This is a total measurement of the business of this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Airespace AP profile. FAIL indicates the Airespace AP is not performing adequately against the LOAD profile.
OBJECT-TYPE    
  ProfileState  

bsnAPIfInterferenceProfileState 1.3.6.1.4.1.14179.2.2.16.1.2
This field represents the current state of Interference monitor. This is a total measurement of the interference present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Interference profile. FAIL indicates the Airespace AP is not performing adequately against the Interference profile.
OBJECT-TYPE    
  ProfileState  

bsnAPIfNoiseProfileState 1.3.6.1.4.1.14179.2.2.16.1.3
This field represents the current state of Noise monitor. This is a total measurement of the noise present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the noise profile. FAIL indicates the Airespace AP is not performing adequately against the noise profile.
OBJECT-TYPE    
  ProfileState  

bsnAPIfCoverageProfileState 1.3.6.1.4.1.14179.2.2.16.1.24
This field represents the current state of coverage monitor. This is a total measurement of the client coverage at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the coverage profile. FAIL indicates the Airespace AP is not performing adequately against the coverage profile.
OBJECT-TYPE    
  ProfileState  

bsnAPIfRxNeighborsTable 1.3.6.1.4.1.14179.2.2.17
This is a table of Rx Neighbors for each Airespace AP with their RSSI value.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRxNeighborsEntry

bsnAPIfRxNeighborsEntry 1.3.6.1.4.1.14179.2.2.17.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress bsnAPIfSlotId, bsnAPIfRxNeighborMacAddress
OBJECT-TYPE    
  BsnAPIfRxNeighborsEntry  

bsnAPIfRxNeighborMacAddress 1.3.6.1.4.1.14179.2.2.17.1.1
MAC Address of Rx Neighbor of the Airespace AP
OBJECT-TYPE    
  MacAddress  

bsnAPIfRxNeighborIpAddress 1.3.6.1.4.1.14179.2.2.17.1.2
IP Address of Rx Neighbor of the Airespace AP
OBJECT-TYPE    
  IpAddress  

bsnAPIfRxNeighborRSSI 1.3.6.1.4.1.14179.2.2.17.1.3
RSSI value of the Rx Neighbor
OBJECT-TYPE    
  Integer32  

bsnAPIfRxNeighborSlot 1.3.6.1.4.1.14179.2.2.17.1.24
Slot value of the Rx Neighbor
OBJECT-TYPE    
  Integer32  

bsnAPIfStationRSSICoverageInfoTable 1.3.6.1.4.1.14179.2.2.18
This is a table of channel information like interference and noise from other 802.11 networks on each channel.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfStationRSSICoverageInfoEntry

bsnAPIfStationRSSICoverageInfoEntry 1.3.6.1.4.1.14179.2.2.18.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfStationRSSICoverageInfoEntry  

bsnAPIfStationRSSICoverageIndex 1.3.6.1.4.1.14179.2.2.18.1.1
RSSI Coverage Index on AP
OBJECT-TYPE    
  Integer32  

bsnAPIfRSSILevel 1.3.6.1.4.1.14179.2.2.18.1.2
RSSI Level
OBJECT-TYPE    
  Integer32  

bsnAPIfStationCountOnRSSI 1.3.6.1.4.1.14179.2.2.18.1.23
Number of stations on this RSSI Level
OBJECT-TYPE    
  Integer32  

bsnAPIfStationSNRCoverageInfoTable 1.3.6.1.4.1.14179.2.2.19
This is a table of Signal to Noise ratio Coverage information on an AP Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfStationSNRCoverageInfoEntry

bsnAPIfStationSNRCoverageInfoEntry 1.3.6.1.4.1.14179.2.2.19.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfStationSNRCoverageInfoEntry  

bsnAPIfStationSNRCoverageIndex 1.3.6.1.4.1.14179.2.2.19.1.1
SNR Coverage Index on AP
OBJECT-TYPE    
  Integer32  

bsnAPIfSNRLevel 1.3.6.1.4.1.14179.2.2.19.1.2
SNR Level
OBJECT-TYPE    
  Integer32  

bsnAPIfStationCountOnSNR 1.3.6.1.4.1.14179.2.2.19.1.23
Number of stations on this SNR Level
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedRFParametersTable 1.3.6.1.4.1.14179.2.2.20
This table list Best Channel,Best TxPowerLevel, Best RTSThreshold,Best FragmentationThreshold etc for this AP Interface as determined by RRM.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRecommendedRFParametersEntry

bsnAPIfRecommendedRFParametersEntry 1.3.6.1.4.1.14179.2.2.20.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
OBJECT-TYPE    
  BsnAPIfRecommendedRFParametersEntry  

bsnAPIfRecommendedChannelNumber 1.3.6.1.4.1.14179.2.2.20.1.1
Recommended ChannelNumber by RRM for this APIf
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedTxPowerLevel 1.3.6.1.4.1.14179.2.2.20.1.2
Recommended TxPowerLevel by RRM for this APIf
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedRTSThreshold 1.3.6.1.4.1.14179.2.2.20.1.3
Recommended RTSThreshold by RRM for this APIf
OBJECT-TYPE    
  Integer32  

bsnAPIfRecommendedFragmentationThreshold 1.3.6.1.4.1.14179.2.2.20.1.24
Recommended Fragmentation Threshold by RRM for this APIf
OBJECT-TYPE    
  Integer32  

bsnAPIfWlanOverrideTable 1.3.6.1.4.1.14179.2.2.21
Each entry represents an SSID added to the AP when the attribute bsnAPIfWlanOverride on the radio is enabled. This means only those WLANs on the switch that are added to this table will be available on such a radio.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfWlanOverrideEntry

bsnAPIfWlanOverrideEntry 1.3.6.1.4.1.14179.2.2.21.1
An entry in bsnAPIfWlanOverrideTable
OBJECT-TYPE    
  BsnAPIfWlanOverrideEntry  

bsnAPIfWlanOverrideId 1.3.6.1.4.1.14179.2.2.21.1.1
Index of the WLAN (bsnDot11EssIndex) added to the radio. Airespace Switch supports 16 Airespace WLANs so index will be from 1 to 16.
OBJECT-TYPE    
  Unsigned32 1..16  

bsnAPIfWlanOverrideSsid 1.3.6.1.4.1.14179.2.2.21.1.2
SSID assigned to the override WLAN.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnAPIfWlanOverrideRowStatus 1.3.6.1.4.1.14179.2.2.21.1.15
A row status type for the bsnAPIfWlanOverrideEntry
OBJECT-TYPE    
  RowStatus  

bsnMeshNodeTable 1.3.6.1.4.1.14179.2.2.22
This is a table of mesh nodes.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMeshNodeEntry

bsnMeshNodeEntry 1.3.6.1.4.1.14179.2.2.22.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress
OBJECT-TYPE    
  BsnMeshNodeEntry  

bsnMeshNodeRole 1.3.6.1.4.1.14179.2.2.22.1.1
the role of this AP
OBJECT-TYPE    
  INTEGER pap(0), rap(1)  

bsnMeshNodeGroup 1.3.6.1.4.1.14179.2.2.22.1.2
the bridge group name of this AP
OBJECT-TYPE    
  OCTET STRING SIZE(0..10)  

bsnMeshNodeBackhaul 1.3.6.1.4.1.14179.2.2.22.1.3
the backhaul radio device for this AP
OBJECT-TYPE    
  INTEGER dot11a(0), dot11b(1), dot11g(2)  

bsnMeshNodeBackhaulPAP 1.3.6.1.4.1.14179.2.2.22.1.4
the backhaul
OBJECT-TYPE    
  INTEGER auto(0), dot11a(1), dot11b(2), dot11g(3)  

bsnMeshNodeBackhaulRAP 1.3.6.1.4.1.14179.2.2.22.1.5
the backhaul radio device for this AP
OBJECT-TYPE    
  INTEGER dot11a(0), dot11b(1), dot11g(2)  

bsnMeshNodeDataRate 1.3.6.1.4.1.14179.2.2.22.1.6
this nodes backhaul data rate
OBJECT-TYPE    
  Integer32  

bsnMeshNodeChannel 1.3.6.1.4.1.14179.2.2.22.1.7
this nodes backhaul channel
OBJECT-TYPE    
  Integer32  

bsnMeshNodeRoutingState 1.3.6.1.4.1.14179.2.2.22.1.8
routing state
OBJECT-TYPE    
  INTEGER start(1), seek(2), sync(3), auth(4), maint(5)  

bsnMeshNodeMalformedNeighPackets 1.3.6.1.4.1.14179.2.2.22.1.9
the number of malformed neighbor packets.
OBJECT-TYPE    
  Counter32  

bsnMeshNodePoorNeighSnr 1.3.6.1.4.1.14179.2.2.22.1.10
poor neighbor snr
OBJECT-TYPE    
  Counter32  

bsnMeshNodeBlacklistPackets 1.3.6.1.4.1.14179.2.2.22.1.11
the number of blacklist packets received
OBJECT-TYPE    
  Counter32  

bsnMeshNodeInsufficientMemory 1.3.6.1.4.1.14179.2.2.22.1.12
occurences of insufficient memory conditions
OBJECT-TYPE    
  Counter32  

bsnMeshNodeRxNeighReq 1.3.6.1.4.1.14179.2.2.22.1.13
Rx neighbor requests
OBJECT-TYPE    
  Counter32  

bsnMeshNodeRxNeighRsp 1.3.6.1.4.1.14179.2.2.22.1.14
Rx neighbor responses
OBJECT-TYPE    
  Counter32  

bsnMeshNodeTxNeighReq 1.3.6.1.4.1.14179.2.2.22.1.15
Tx neighbor requests
OBJECT-TYPE    
  Counter32  

bsnMeshNodeTxNeighRsp 1.3.6.1.4.1.14179.2.2.22.1.16
Tx neighbor responses
OBJECT-TYPE    
  Counter32  

bsnMeshNodeParentChanges 1.3.6.1.4.1.14179.2.2.22.1.17
number of parent changes
OBJECT-TYPE    
  Counter32  

bsnMeshNodeNeighTimeout 1.3.6.1.4.1.14179.2.2.22.1.18
number of neighbor timeouts
OBJECT-TYPE    
  Counter32  

bsnMeshNodeParentMacAddress 1.3.6.1.4.1.14179.2.2.22.1.19
parents mac addressed
OBJECT-TYPE    
  MacAddress  

bsnMeshNodeAPType 1.3.6.1.4.1.14179.2.2.22.1.20
the type of AP
OBJECT-TYPE    
  INTEGER indoorBridge(5), outdoorBridge(6)  

bsnMeshNodeEthernetBridge 1.3.6.1.4.1.14179.2.2.22.1.21
enable : Enables ethernet bridging on the AP. disable : Disables ethernet bridging on the AP. Changes are only applicable when AP is in 'Bridge' mode.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMeshNodeHops 1.3.6.1.4.1.14179.2.2.22.1.30
number of hops to rap
OBJECT-TYPE    
  Integer32  

bsnMeshNeighsTable 1.3.6.1.4.1.14179.2.2.23
This is a table of mesh neighbors.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMeshNeighsEntry

bsnMeshNeighsEntry 1.3.6.1.4.1.14179.2.2.23.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnMeshNeighNeighMacAddress
OBJECT-TYPE    
  BsnMeshNeighsEntry  

bsnMeshNeighMacAddress 1.3.6.1.4.1.14179.2.2.23.1.1
MAC Address of neighbor
OBJECT-TYPE    
  MacAddress  

bsnMeshNeighType 1.3.6.1.4.1.14179.2.2.23.1.2
neighbor type
OBJECT-TYPE    
  INTEGER parent(0), tentparent(1), neigh(2), blacklisted(3), child(4)  

bsnMeshNeighState 1.3.6.1.4.1.14179.2.2.23.1.3
neighbor state
OBJECT-TYPE    
  INTEGER updated(0), needupdate(1)  

bsnMeshNeighSnr 1.3.6.1.4.1.14179.2.2.23.1.4
explicitly set SNR
OBJECT-TYPE    
  Integer32  

bsnMeshNeighSnrUp 1.3.6.1.4.1.14179.2.2.23.1.5
snr up
OBJECT-TYPE    
  Integer32  

bsnMeshNeighSnrDown 1.3.6.1.4.1.14179.2.2.23.1.6
snr down
OBJECT-TYPE    
  Integer32  

bsnMeshNeighLinkSnr 1.3.6.1.4.1.14179.2.2.23.1.7
link snr
OBJECT-TYPE    
  Integer32  

bsnMeshNeighAdjustedEase 1.3.6.1.4.1.14179.2.2.23.1.8
hops adjusted ease
OBJECT-TYPE    
  Integer32  

bsnMeshNeighUnadjustedEase 1.3.6.1.4.1.14179.2.2.23.1.9
ease to root AP from this AP
OBJECT-TYPE    
  Integer32  

bsnMeshNeighRapEase 1.3.6.1.4.1.14179.2.2.23.1.10
unadjusted ease received in last hello
OBJECT-TYPE    
  Integer32  

bsnMeshNeighTxParent 1.3.6.1.4.1.14179.2.2.23.1.11
tx packets to this node while a parent
OBJECT-TYPE    
  Counter32  

bsnMeshNeighRxParent 1.3.6.1.4.1.14179.2.2.23.1.12
rx packets from this node while a parent
OBJECT-TYPE    
  Counter32  

bsnMeshNeighPoorSnr 1.3.6.1.4.1.14179.2.2.23.1.13
packets with poor snr received from this node
OBJECT-TYPE    
  Counter32  

bsnMeshNeighLastUpdate 1.3.6.1.4.1.14179.2.2.23.1.14
last received hello from this neighbor
OBJECT-TYPE    
  Integer32  

bsnMeshNeighParentChange 1.3.6.1.4.1.14179.2.2.23.1.20
when this node last became parent
OBJECT-TYPE    
  Integer32  

bsnAPIfRadarChannelStatisticsTable 1.3.6.1.4.1.14179.2.2.24
This is a table of channel information on which radar signal were detected. This will give the list of channels and last heard timestamp. Radar signals are detected only on 5Ghz range. So this will be detected for 802.11a interface.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPIfRadarChannelStatisticsEntry

bsnAPIfRadarChannelStatisticsEntry 1.3.6.1.4.1.14179.2.2.24.1
An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId, bsnAPIfRadarDetectedCannelNumber.
OBJECT-TYPE    
  BsnAPIfRadarChannelStatisticsEntry  

bsnAPIfRadarDetectedChannelNumber 1.3.6.1.4.1.14179.2.2.24.1.1
Channel Number on which radar signals were detected.
OBJECT-TYPE    
  Integer32  

bsnAPIfRadarSignalLastHeard 1.3.6.1.4.1.14179.2.2.24.1.2
This tells how many seconds ago radar signal was heard on the channel.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11 1.3.6.1.4.1.14179.2.3
OBJECT IDENTIFIER    

bsnGlobalDot11Config 1.3.6.1.4.1.14179.2.3.1
OBJECT IDENTIFIER    

bsnGlobalDot11PrivacyOptionImplemented 1.3.6.1.4.1.14179.2.3.1.1
This attribute, when true, shall indicate that the IEEE 802.11 WEP option is implemented. The default value of this attribute shall be false.
OBJECT-TYPE    
  INTEGER notimplemented(0), implemented(1)  

bsnGlobalDot11AuthenticationResponseTimeOut 1.3.6.1.4.1.14179.2.3.1.2
This attribute shall specify the number of TU that a responding STA should wait for the next frame in the authentication sequence.
OBJECT-TYPE    
  Unsigned32 5..60  

bsnGlobalDot11MultiDomainCapabilityImplemented 1.3.6.1.4.1.14179.2.3.1.3
This attribute, when TRUE, indicates that the station implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11MultiDomainCapabilityEnabled 1.3.6.1.4.1.14179.2.3.1.4
This attribute, when TRUE, indicates that the capability of the station to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11CountryIndex 1.3.6.1.4.1.14179.2.3.1.5
This attribute identifies the country in which the station is operating.
OBJECT-TYPE    
  INTEGER usa(1), canada(2), france(3), japan(4), mexico(5), spain(6), usalegacy(7), korearepublic(8), australia(9), austria(10), belgium(11), denmark(12), finland(13), germany(14), greece(15), ireland(16), italy(17), luxembourg(18), netherlands(19), portugal(20), sweden(21), unitedkingdom(22), none(23), india(24), hongkong(25), switzerland(26), iceland(27), norway(28), singapore(29), thailand(30), taiwan(31), cyprus(33), czechrepublic(34), estonia(35), hungary(36), lithuania(37), latvia(38), malaysia(39), newzealand(40), poland(41), slovenia(42), slovakrepublic(43), southafrica(44), usachan165(45), israel(46), israelOutdoor(47), argentina(48), brazil(49), saudiArabia(51), turkey(52), indonesia(53), china(54), koreaExtended(55), japan2(56), gibraltar(57), liechtenstein(58), malta(59), monaco(60), romania(61), russianfederation(62), chile(63), colombia(64), panama(65), peru(66), venezuela(67), philippines(68)  

bsnGlobalDot11LoadBalancing 1.3.6.1.4.1.14179.2.3.1.6
This attribute specifies if load balancing of clients is enabled on disabled.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11RogueTimer 1.3.6.1.4.1.14179.2.3.1.7
This attribute specifies in seconds, the time interval after which a Rogue Entry in Rogue Table will expire if no beacon is heard from a Rogue.
OBJECT-TYPE    
  Integer32 120..3600  

bsnPrimaryMwarForAPs 1.3.6.1.4.1.14179.2.3.1.8
This attribute specifies if this Switch acts a Master Switch for the Airespace APs. So if an Airespace AP doesn't find its Primary Switch, it will associate with this Switch.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRtpProtocolPriority 1.3.6.1.4.1.14179.2.3.1.9
Real Time Protocol Priority.
OBJECT-TYPE    
  INTEGER nopriority(0), highpriority(1)  

bsnSystemCurrentTime 1.3.6.1.4.1.14179.2.3.1.10
This attribute will display the Current System time on the Switch.
OBJECT-TYPE    
  DisplayString  

bsnUpdateSystemTime 1.3.6.1.4.1.14179.2.3.1.11
Use this attribute to change the System time on the Switch. Specify the new time in this Format MM/DD/YYYY HH:MM:SS
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

bsnOperatingTemperatureEnvironment 1.3.6.1.4.1.14179.2.3.1.12
Operating Environment of the Airespace Switch. commercial is Commercial (0 to 40 C) and industrial is Industrial (-10 to 70 C)
OBJECT-TYPE    
  INTEGER commercial(1), industrial(2), unknown(0)  

bsnSensorTemperature 1.3.6.1.4.1.14179.2.3.1.13
Current Internal Temperature of the unit in Centigrade
OBJECT-TYPE    
  Integer32  

bsnTemperatureAlarmLowLimit 1.3.6.1.4.1.14179.2.3.1.14
Internal Temperature Alarm Low Limit in Centigrade. If the bsnSensorTemperature goes below this limit bsnSensedTemperatureTooLow Alarm will be sent out
OBJECT-TYPE    
  Integer32  

bsnTemperatureAlarmHighLimit 1.3.6.1.4.1.14179.2.3.1.15
Internal Temperature Alarm High Limit in Centigrade. If the bsnSensorTemperature goes above this limit bsnSensedTemperatureTooHigh Alarm will be sent out
OBJECT-TYPE    
  Integer32  

bsnVirtualGatewayAddress 1.3.6.1.4.1.14179.2.3.1.16
Virtual Gateway Address of the Switch. This is used by web auth and Ipsec. If the virtual IP Address is changed, the Switch has to be rebooted for the new Address to take effect. This is now replaced by the Virtual Interface in bsnswitching MIB.
OBJECT-TYPE    
  IpAddress  

bsnRFMobilityDomainName 1.3.6.1.4.1.14179.2.3.1.17
RF Mobility Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Group as well as a Mobility Group. RF Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnClientWatchListFeature 1.3.6.1.4.1.14179.2.3.1.18
This flag should be turned on for the client watch lists to be enabled on the switch. When enabled, the switch generates Client Association and Authentication traps for the watchlisted clients.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRogueLocationDiscoveryProtocol 1.3.6.1.4.1.14179.2.3.1.19
This flag should be turned on to enable the Rogue Location Discovery Protocol feature on the switch.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRogueAutoContainFeature 1.3.6.1.4.1.14179.2.3.1.20
This flag should be turned on to allow the switch to contain the rogues automatically if detected on the wired network.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnOverAirProvisionApMode 1.3.6.1.4.1.14179.2.3.1.21
Over the Air Provisioning Mode for APs
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMaximumNumberOfConcurrentLogins 1.3.6.1.4.1.14179.2.3.1.22
This attribute specifies the maximum number of concurrent logins that the switch will allow for a single user. A value 0 implies that there is no restriction on the number of concurrent logins with a single username.
OBJECT-TYPE    
  Integer32 0..8  

bsnAutoContainRoguesAdvertisingSsid 1.3.6.1.4.1.14179.2.3.1.23
This flag should be set to 1 to allow the switch to contain automatically those rogues that are advertising our SSID. If value is 0, only an alarm will be generated when such a rogue is detected.
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnAutoContainAdhocNetworks 1.3.6.1.4.1.14179.2.3.1.24
This flag should be set to 1 to allow the switch to contain automatically the adhoc networks detected by the switch. If value is 0, only an alarm will be generated when such a network is detected.
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnAutoContainTrustedClientsOnRogueAps 1.3.6.1.4.1.14179.2.3.1.25
This flag should be set to 1 to allow the switch to contain automatically those trusted clients that are associated to rogue APs. If value is 0, only an alarm will be generated when such a client is detected.
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnValidateRogueClientsAgainstAAA 1.3.6.1.4.1.14179.2.3.1.26
This flag should be turned on to allow the switch to validate 'valid' mobiles associating with rogue APs. For example, if a client's MAC Address is found in the local MAC filter table, that client can be validated.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSystemTimezoneDelta 1.3.6.1.4.1.14179.2.3.1.27
The delta (difference) between the local time and the Universal Coordinated Time in hours. For example, it is -8 for the PST and +1 for France. If the delta is -5.30 then this attribute will store -5 and bsnSystemTimezoneDeltaMinutes will store 30. This value i should be between -23 to +23
OBJECT-TYPE    
  Integer32  

bsnSystemTimezoneDaylightSavings 1.3.6.1.4.1.14179.2.3.1.28
This flag specifies if daylight savings are enabled for the current timezone.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAllowAuthorizeApAgainstAAA 1.3.6.1.4.1.14179.2.3.1.29
This flag specifies if LWAPP is allowed to get authorization via RADIUS or local database for an AP.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSystemTimezoneDeltaMinutes 1.3.6.1.4.1.14179.2.3.1.30
The minutes component of delta (difference) between the local time and the Universal Coordinated Time.
OBJECT-TYPE    
  Integer32  

bsnApFallbackEnabled 1.3.6.1.4.1.14179.2.3.1.31
This flag specifies if the APs should continue LWAPP discoveries to fallback to the primary switch in case they are not already associated with it i.e they are associated with their respective secondary or tertiary switch instead.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAppleTalkEnabled 1.3.6.1.4.1.14179.2.3.1.32
This flag turns on the appletalk bridging in the switch such that the packets from Apple clients that use appletalk format can be processed by the switch. When this flag is off, these packets are dropped.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnTrustedApPolicyConfig 1.3.6.1.4.1.14179.2.3.1.40
OBJECT IDENTIFIER    

bsnPolicyForMisconfiguredAps 1.3.6.1.4.1.14179.2.3.1.40.1
This flag should be turned on to allow the switch to contain misconfigured APs.
OBJECT-TYPE    
  INTEGER alarmOnly(0), contain(1)  

bsnEncryptionPolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.2
The encryption policy that is enforced on the trusted APs.
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnPreamblePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.3
The preamble policy that is enforced on the trusted APs.
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnDot11ModePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.4
The 802.11 Mode policy that is enforced on the trusted APs.
OBJECT-TYPE    
  INTEGER none(0), dcfOnly(1), pcfOnly(2)  

bsnRadioTypePolicyEnforced 1.3.6.1.4.1.14179.2.3.1.40.5
The radio type policy that is enforced on the trusted APs.
OBJECT-TYPE    
  INTEGER none(0), aOnly(1), bOnly(2), bgOnly(3)  

bsnValidateSsidForTrustedAp 1.3.6.1.4.1.14179.2.3.1.40.6
If enabled, the SSID of trusted APs will be validated by the switch.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAlertIfTrustedApMissing 1.3.6.1.4.1.14179.2.3.1.40.7
If enabled, an alert will be generated when a trusted AP is missing.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnTrustedApEntryExpirationTimeout 1.3.6.1.4.1.14179.2.3.1.40.8
This attribute specifies in seconds, the time interval after which a Trusted AP Entry will expire if no beacon is heard from that AP.
OBJECT-TYPE    
  Integer32 120..3600  

bsnClientExclusionPolicyConfig 1.3.6.1.4.1.14179.2.3.1.41
OBJECT IDENTIFIER    

bsnExcessive80211AssocFailures 1.3.6.1.4.1.14179.2.3.1.41.1
This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Association Failures occurs with a client.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessive80211AuthFailures 1.3.6.1.4.1.14179.2.3.1.41.2
This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Authentication Failures occurs with a client.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessive8021xAuthFailures 1.3.6.1.4.1.14179.2.3.1.41.3
This flag specifies if client should be excluded (blacklisted) if repeated 802.1x Authentication Failures occurs with a client.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExternalPolicyServerFailures 1.3.6.1.4.1.14179.2.3.1.41.4
This flag specifies if client should be excluded (blacklisted) if repeated external policy server failures occurs with a client.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExcessiveWebAuthFailures 1.3.6.1.4.1.14179.2.3.1.41.5
This flag specifies if client should be excluded (blacklisted) if repeated Web Authentication Failures occurs with a client.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnIPTheftORReuse 1.3.6.1.4.1.14179.2.3.1.41.6
This flag specifies if client should be excluded (blacklisted) if it appears to be reusing an IP Address.(Possible IP Theft)
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSignatureConfig 1.3.6.1.4.1.14179.2.3.1.42
OBJECT IDENTIFIER    

bsnStandardSignatureTable 1.3.6.1.4.1.14179.2.3.1.42.1
The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnStandardSignatureEntry

bsnStandardSignatureEntry 1.3.6.1.4.1.14179.2.3.1.42.1.1
....
OBJECT-TYPE    
  BsnStandardSignatureEntry  

bsnStandardSignaturePrecedence 1.3.6.1.4.1.14179.2.3.1.42.1.1.1
Precedence of the signature. This specifies the order in which the signature is applied to a packet.
OBJECT-TYPE    
  Unsigned32 1..100  

bsnStandardSignatureName 1.3.6.1.4.1.14179.2.3.1.42.1.1.2
This attribute is used to configure the name on a signature.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

bsnStandardSignatureDescription 1.3.6.1.4.1.14179.2.3.1.42.1.1.3
This attribute is used to configure the description of a signature.
OBJECT-TYPE    
  DisplayString SIZE(0..100)  

bsnStandardSignatureFrameType 1.3.6.1.4.1.14179.2.3.1.42.1.1.4
This attribute specifies the type of frame that needs to match a signature.
OBJECT-TYPE    
  INTEGER management(0), data(1)  

bsnStandardSignatureAction 1.3.6.1.4.1.14179.2.3.1.42.1.1.5
This attribute specifies the action to be taken once a packet is found to match a signature.
OBJECT-TYPE    
  INTEGER none(0), report(1), contain(2), exclude(3)  

bsnStandardSignatureState 1.3.6.1.4.1.14179.2.3.1.42.1.1.6
This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnStandardSignatureFrequency 1.3.6.1.4.1.14179.2.3.1.42.1.1.7
This specifies the frequency of the matching packets after which the specified action is taken.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureQuietTime 1.3.6.1.4.1.14179.2.3.1.42.1.1.8
This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureVersion 1.3.6.1.4.1.14179.2.3.1.42.1.1.9
This specifies the signature version.
OBJECT-TYPE    
  Unsigned32 0..128  

bsnStandardSignatureConfigType 1.3.6.1.4.1.14179.2.3.1.42.1.1.10
This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be i configured in later releases.
OBJECT-TYPE    
  INTEGER pattern(0), protocol(1)  

bsnStandardSignatureEnable 1.3.6.1.4.1.14179.2.3.1.42.1.1.11
This object configures the status of a particular standard signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
OBJECT-TYPE    
  TruthValue  

bsnStandardSignatureMacInfo 1.3.6.1.4.1.14179.2.3.1.42.1.1.12
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Standard signature and report the results to the Controller.
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnStandardSignatureMacFreq 1.3.6.1.4.1.14179.2.3.1.42.1.1.13
This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnStandardSignatureRowStatus 1.3.6.1.4.1.14179.2.3.1.42.1.1.20
Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
OBJECT-TYPE    
  RowStatus  

bsnStandardSignaturePatternTable 1.3.6.1.4.1.14179.2.3.1.42.2
The table listing the matching patterns specified for a i Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 i patterns may be specifed for a signature. These are used for matching in the order of their index.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnStandardSignaturePatternEntry

bsnStandardSignaturePatternEntry 1.3.6.1.4.1.14179.2.3.1.42.2.1
....
OBJECT-TYPE    
  BsnStandardSignaturePatternEntry  

bsnStandardSignaturePatternIndex 1.3.6.1.4.1.14179.2.3.1.42.2.1.1
Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
OBJECT-TYPE    
  Unsigned32 1..5  

bsnStandardSignaturePatternOffset 1.3.6.1.4.1.14179.2.3.1.42.2.1.2
Offset from the start of the packet where the AP looks for a match to the pattern.
OBJECT-TYPE    
  Unsigned32 0..128  

bsnStandardSignaturePatternString 1.3.6.1.4.1.14179.2.3.1.42.2.1.3
This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

bsnStandardSignaturePatternMask 1.3.6.1.4.1.14179.2.3.1.42.2.1.4
This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

bsnStandardSignaturePatternOffSetStart 1.3.6.1.4.1.14179.2.3.1.42.2.1.5
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this standard signature.
OBJECT-TYPE    
  BsnSignaturePatternOffSetStart  

bsnStandardSignaturePatternRowStatus 1.3.6.1.4.1.14179.2.3.1.42.2.1.15
Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
OBJECT-TYPE    
  RowStatus  

bsnCustomSignatureTable 1.3.6.1.4.1.14179.2.3.1.42.3
The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnCustomSignatureEntry

bsnCustomSignatureEntry 1.3.6.1.4.1.14179.2.3.1.42.3.1
....
OBJECT-TYPE    
  BsnCustomSignatureEntry  

bsnCustomSignaturePrecedence 1.3.6.1.4.1.14179.2.3.1.42.3.1.1
Precedence of the signature. This specifies the order in which the signature is applied to a packet.
OBJECT-TYPE    
  Unsigned32 1..100  

bsnCustomSignatureName 1.3.6.1.4.1.14179.2.3.1.42.3.1.2
This attribute is used to configure the name on a signature.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

bsnCustomSignatureDescription 1.3.6.1.4.1.14179.2.3.1.42.3.1.3
This attribute is used to configure the description of a signature.
OBJECT-TYPE    
  DisplayString SIZE(0..100)  

bsnCustomSignatureFrameType 1.3.6.1.4.1.14179.2.3.1.42.3.1.4
This attribute specifies the type of frame that needs to match a signature.
OBJECT-TYPE    
  INTEGER management(0), data(1)  

bsnCustomSignatureAction 1.3.6.1.4.1.14179.2.3.1.42.3.1.5
This attribute specifies the action to be taken once a packet is found to match a signature.
OBJECT-TYPE    
  INTEGER none(0), report(1), contain(2), exclude(3)  

bsnCustomSignatureState 1.3.6.1.4.1.14179.2.3.1.42.3.1.6
This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bsnCustomSignatureFrequency 1.3.6.1.4.1.14179.2.3.1.42.3.1.7
This specifies the frequency of the matching packets after which the specified action is taken.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureQuietTime 1.3.6.1.4.1.14179.2.3.1.42.3.1.8
This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureVersion 1.3.6.1.4.1.14179.2.3.1.42.3.1.9
This specifies the signature version.
OBJECT-TYPE    
  Unsigned32 0..128  

bsnCustomSignatureConfigType 1.3.6.1.4.1.14179.2.3.1.42.3.1.10
This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be configured in later releases.
OBJECT-TYPE    
  INTEGER pattern(0), protocol(1)  

bsnCustomSignatureEnable 1.3.6.1.4.1.14179.2.3.1.42.3.1.11
This object configures the status of a particular Custom signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
OBJECT-TYPE    
  TruthValue  

bsnCustomSignatureMacInfo 1.3.6.1.4.1.14179.2.3.1.42.3.1.12
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Custom signature and report the results to the Controller.
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnCustomSignatureMacFreq 1.3.6.1.4.1.14179.2.3.1.42.3.1.13
This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnCustomSignatureRowStatus 1.3.6.1.4.1.14179.2.3.1.42.3.1.20
Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
OBJECT-TYPE    
  RowStatus  

bsnCustomSignaturePatternTable 1.3.6.1.4.1.14179.2.3.1.42.4
The table listing the matching patterns specified for a Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 patterns may be specifed for a signature. These are used for matching in the order of their index.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnCustomSignaturePatternEntry

bsnCustomSignaturePatternEntry 1.3.6.1.4.1.14179.2.3.1.42.4.1
....
OBJECT-TYPE    
  BsnCustomSignaturePatternEntry  

bsnCustomSignaturePatternIndex 1.3.6.1.4.1.14179.2.3.1.42.4.1.1
Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
OBJECT-TYPE    
  Unsigned32 1..5  

bsnCustomSignaturePatternOffset 1.3.6.1.4.1.14179.2.3.1.42.4.1.2
Offset from the start of the packet where the AP looks for a match to the pattern.
OBJECT-TYPE    
  Unsigned32 0..128  

bsnCustomSignaturePatternString 1.3.6.1.4.1.14179.2.3.1.42.4.1.3
This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

bsnCustomSignaturePatternMask 1.3.6.1.4.1.14179.2.3.1.42.4.1.4
This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

bsnCustomSignaturePatternOffSetStart 1.3.6.1.4.1.14179.2.3.1.42.4.1.5
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this custom signature.
OBJECT-TYPE    
  BsnSignaturePatternOffSetStart  

bsnCustomSignaturePatternRowStatus 1.3.6.1.4.1.14179.2.3.1.42.4.1.15
Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
OBJECT-TYPE    
  RowStatus  

bsnSignatureCheckState 1.3.6.1.4.1.14179.2.3.1.42.5
This flag should be enabled to enforce check of all standard and custom signatures. If disabled, there will be no check for signatures, both custom and standard, by the switch.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRfIdTagConfig 1.3.6.1.4.1.14179.2.3.1.43
OBJECT IDENTIFIER    

bsnRfIdTagStatus 1.3.6.1.4.1.14179.2.3.1.43.1
This flag should be turned on to allow the switch to collect data for tags.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRfIdTagDataTimeout 1.3.6.1.4.1.14179.2.3.1.43.2
This is the number of seconds after which the tag data is deleted by the switch from its database if it didn't hear from the tag again.
OBJECT-TYPE    
  Unsigned32 60..7200  

bsnRfIdTagAutoTimeoutStatus 1.3.6.1.4.1.14179.2.3.1.43.3
This flag should be turned on to allow auto deletion of tag data in the switch after expiration of Tag Data Timeout
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNeighborAuthConfig 1.3.6.1.4.1.14179.2.3.1.44
OBJECT IDENTIFIER    

bsnAPNeighborAuthStatus 1.3.6.1.4.1.14179.2.3.1.44.1
This flag should be turned on to allow the AP-Neighbor Authentication feature.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPNeighborAuthAlarmThreshold 1.3.6.1.4.1.14179.2.3.1.44.2
Authentication alarm trigger threshold.
OBJECT-TYPE    
  INTEGER 1..255  

bsnRFNetworkName 1.3.6.1.4.1.14179.2.3.1.45
RF Network Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Network Group as well as a Mobility Group. RF Network Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
OBJECT-TYPE    
  OCTET STRING SIZE(0..19)  

bsnFastSSIDChangeFeature 1.3.6.1.4.1.14179.2.3.1.46
Configures Fast SSID changing feature for mobile-stations. When enabled, permits mobile-stations to change SSIDs without having to block and wait for SSID-cleanup on the switch to occur.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnBridgingPolicyConfig 1.3.6.1.4.1.14179.2.3.1.47
OBJECT IDENTIFIER    

bsnBridgingZeroTouchConfig 1.3.6.1.4.1.14179.2.3.1.47.1
If enabled, allows new bridging APs to negotiate with the switch to acquire the shared secret key.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnBridgingSharedSecretKey 1.3.6.1.4.1.14179.2.3.1.47.2
Key that is used to negotiate a secure LWAPP connection between a switch and a bridging or mesh AP.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnAcceptSelfSignedCertificate 1.3.6.1.4.1.14179.2.3.1.48
This flag specifies if controller will accept Self Signed Certificate from AP as part of authorization.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSystemClockTime 1.3.6.1.4.1.14179.2.3.1.49
This object represents the current clock time of the controller and expressed as the number of seconds elapsed since 00:00:00 on January 1, 1970, Coordinated Universal Time (UTC).
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11b 1.3.6.1.4.1.14179.2.3.2
OBJECT IDENTIFIER    

bsnGlobalDot11bConfig 1.3.6.1.4.1.14179.2.3.2.1
OBJECT IDENTIFIER    

bsnGlobalDot11bNetworkStatus 1.3.6.1.4.1.14179.2.3.2.1.1
802.11b Network Admin Status.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bBeaconPeriod 1.3.6.1.4.1.14179.2.3.2.1.2
This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
OBJECT-TYPE    
  INTEGER 20..1000  

bsnGlobalDot11bDynamicChannelAssignment 1.3.6.1.4.1.14179.2.3.2.1.3
Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11bCurrentChannel 1.3.6.1.4.1.14179.2.3.2.1.4
The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in 15.4.6.2. This attribute will be read-only if bsnAPIfPhyChannelAutomaticOn is true.
OBJECT-TYPE    
  INTEGER 1..14  

bsnGlobalDot11bDynamicChannelUpdateInterval 1.3.6.1.4.1.14179.2.3.2.1.5
When Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is built into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bInputsForDCA 1.3.6.1.4.1.14179.2.3.2.1.6
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 Default value is 15( all bits on).
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bChannelUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.2.1.7
When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11bChannelUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.2.1.8
After setting bsnGlobalDot11bChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bDynamicTransmitPowerControl 1.3.6.1.4.1.14179.2.3.2.1.9
Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11bDynamicTxPowerControlInterval 1.3.6.1.4.1.14179.2.3.2.1.10
When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bCurrentTxPowerLevel 1.3.6.1.4.1.14179.2.3.2.1.11
The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
OBJECT-TYPE    
  INTEGER 1..5  

bsnGlobalDot11bInputsForDTP 1.3.6.1.4.1.14179.2.3.2.1.12
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11bPowerUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.2.1.13
When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11bPowerUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.2.1.14
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bDataRate1Mhz 1.3.6.1.4.1.14179.2.3.2.1.15
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate2Mhz 1.3.6.1.4.1.14179.2.3.2.1.16
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate5AndHalfMhz 1.3.6.1.4.1.14179.2.3.2.1.17
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate11Mhz 1.3.6.1.4.1.14179.2.3.2.1.18
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bShortPreamble 1.3.6.1.4.1.14179.2.3.2.1.19
802.11b Short Preamble.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bDot11gSupport 1.3.6.1.4.1.14179.2.3.2.1.20
This attribute is enabled to also support 802.11g protocol on the 802.11b network. Enabling 802.11g allows additional data rates: 6, 9, 12, 18, 24, 36, 48, 54 Mbps.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bDataRate6Mhz 1.3.6.1.4.1.14179.2.3.2.1.21
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate9Mhz 1.3.6.1.4.1.14179.2.3.2.1.22
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate12Mhz 1.3.6.1.4.1.14179.2.3.2.1.23
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate18Mhz 1.3.6.1.4.1.14179.2.3.2.1.24
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate24Mhz 1.3.6.1.4.1.14179.2.3.2.1.25
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate36Mhz 1.3.6.1.4.1.14179.2.3.2.1.26
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate48Mhz 1.3.6.1.4.1.14179.2.3.2.1.27
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bDataRate54Mhz 1.3.6.1.4.1.14179.2.3.2.1.28
Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11bPicoCellMode 1.3.6.1.4.1.14179.2.3.2.1.29
Configures the 802.11b pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnGlobalDot11bFastRoamingMode 1.3.6.1.4.1.14179.2.3.2.1.30
Configures the 802.11b fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bFastRoamingVoipMinRate 1.3.6.1.4.1.14179.2.3.2.1.31
Configures the minimum transmission rate allowed for VoIP on any 802.11b radio.
OBJECT-TYPE    
  INTEGER undefined(0), rate1Mbps(1), rate2Mbps(2), rate5andHalfMbps(3), rate11Mbps(4)  

bsnGlobalDot11bFastRoamingVoipPercentage 1.3.6.1.4.1.14179.2.3.2.1.32
Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
OBJECT-TYPE    
  INTEGER zero(1), twentyfive(2), fifty(3), seventyfive(4), hundred(5)  

bsnGlobalDot11b80211eMaxBandwidth 1.3.6.1.4.1.14179.2.3.2.1.33
This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11b network. The value of this attribute can vary from 0 to 100.
OBJECT-TYPE    
  INTEGER 0..100  

bsnGlobalDot11bDTPCSupport 1.3.6.1.4.1.14179.2.3.2.1.34
This attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11bPhy 1.3.6.1.4.1.14179.2.3.2.2
OBJECT IDENTIFIER    

bsnGlobalDot11bMediumOccupancyLimit 1.3.6.1.4.1.14179.2.3.2.2.1
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
OBJECT-TYPE    
  INTEGER 0..1000  

bsnGlobalDot11bCFPPeriod 1.3.6.1.4.1.14179.2.3.2.2.2
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..255  

bsnGlobalDot11bCFPMaxDuration 1.3.6.1.4.1.14179.2.3.2.2.3
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnGlobalDot11bCFPollable 1.3.6.1.4.1.14179.2.3.2.2.5
When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bCFPollRequest 1.3.6.1.4.1.14179.2.3.2.2.6
Specifies wheather CFP
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bDTIMPeriod 1.3.6.1.4.1.14179.2.3.2.2.7
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bMaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.3.2.2.8
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bFirstChannelNumber 1.3.6.1.4.1.14179.2.3.2.2.9
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bNumberofChannels 1.3.6.1.4.1.14179.2.3.2.2.10
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bRTSThreshold 1.3.6.1.4.1.14179.2.3.2.2.11
This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
OBJECT-TYPE    
  INTEGER 0..2347  

bsnGlobalDot11bShortRetryLimit 1.3.6.1.4.1.14179.2.3.2.2.12
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bLongRetryLimit 1.3.6.1.4.1.14179.2.3.2.2.13
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11bFragmentationThreshold 1.3.6.1.4.1.14179.2.3.2.2.14
This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
OBJECT-TYPE    
  INTEGER 256..2346  

bsnGlobalDot11bMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.3.2.2.15
The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11bMaxReceiveLifetime 1.3.6.1.4.1.14179.2.3.2.2.16
The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11bEDThreshold 1.3.6.1.4.1.14179.2.3.2.2.17
The current Energy Detect Threshold being used by the DSSS PHY.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11bChannelAgilityEnabled 1.3.6.1.4.1.14179.2.3.2.2.18
This attribute indicates that the PHY channel agility functionality is enabled.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bPBCCOptionImplemented 1.3.6.1.4.1.14179.2.3.2.2.19
This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11bShortPreambleOptionImplemented 1.3.6.1.4.1.14179.2.3.2.2.20
This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11a 1.3.6.1.4.1.14179.2.3.3
OBJECT IDENTIFIER    

bsnGlobalDot11aConfig 1.3.6.1.4.1.14179.2.3.3.1
OBJECT IDENTIFIER    

bsnGlobalDot11aNetworkStatus 1.3.6.1.4.1.14179.2.3.3.1.1
Dot11a Network Status
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aLowBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.2
Dot11a Low Band Network Status
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aMediumBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.3
Dot11a Mid Band Network Status
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aHighBandNetwork 1.3.6.1.4.1.14179.2.3.3.1.4
Dot11a High Band Network Status
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aBeaconPeriod 1.3.6.1.4.1.14179.2.3.3.1.5
This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
OBJECT-TYPE    
  INTEGER 20..1000  

bsnGlobalDot11aDynamicChannelAssignment 1.3.6.1.4.1.14179.2.3.3.1.6
Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11aCurrentChannel 1.3.6.1.4.1.14179.2.3.3.1.7
The number of the current operating frequency channel of the OFDM PHY.
OBJECT-TYPE    
  INTEGER 0..99  

bsnGlobalDot11aDynamicChannelUpdateInterval 1.3.6.1.4.1.14179.2.3.3.1.8
When Channel dynamic alogirthm is running, this interval(in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aInputsForDCA 1.3.6.1.4.1.14179.2.3.3.1.9
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 Default value is 15( all bits on).
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aChannelUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.3.1.10
When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11aChannelUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.3.1.11
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aDynamicTransmitPowerControl 1.3.6.1.4.1.14179.2.3.3.1.12
Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
OBJECT-TYPE    
  INTEGER automatic(1), runOnce(2), static(3)  

bsnGlobalDot11aCurrentTxPowerLevel 1.3.6.1.4.1.14179.2.3.3.1.13
The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
OBJECT-TYPE    
  INTEGER 1..5  

bsnGlobalDot11aDynamicTxPowerControlInterval 1.3.6.1.4.1.14179.2.3.3.1.14
When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aInputsForDTP 1.3.6.1.4.1.14179.2.3.3.1.15
This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
OBJECT-TYPE    
  Unsigned32  

bsnGlobalDot11aPowerUpdateCmdInvoke 1.3.6.1.4.1.14179.2.3.3.1.16
When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnGlobalDot11aPowerUpdateCmdStatus 1.3.6.1.4.1.14179.2.3.3.1.17
After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aDataRate6Mhz 1.3.6.1.4.1.14179.2.3.3.1.19
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate9Mhz 1.3.6.1.4.1.14179.2.3.3.1.20
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate12Mhz 1.3.6.1.4.1.14179.2.3.3.1.21
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate18Mhz 1.3.6.1.4.1.14179.2.3.3.1.22
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate24Mhz 1.3.6.1.4.1.14179.2.3.3.1.23
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate36Mhz 1.3.6.1.4.1.14179.2.3.3.1.24
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate48Mhz 1.3.6.1.4.1.14179.2.3.3.1.25
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aDataRate54Mhz 1.3.6.1.4.1.14179.2.3.3.1.26
Specify if this rate is supported or mandatory or disabled
OBJECT-TYPE    
  INTEGER supported(1), mandatory(2), disabled(0)  

bsnGlobalDot11aPicoCellMode 1.3.6.1.4.1.14179.2.3.3.1.27
Configures the 802.11a pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

bsnGlobalDot11aFastRoamingMode 1.3.6.1.4.1.14179.2.3.3.1.28
Configures the 802.11a fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aFastRoamingVoipMinRate 1.3.6.1.4.1.14179.2.3.3.1.29
Configures the minimum transmission rate allowed for VoIP on any 802.11a radio.
OBJECT-TYPE    
  INTEGER undefined(0), rate1Mbps(1), rate2Mbps(2), rate5andHalfMbps(3), rate11Mbps(4)  

bsnGlobalDot11aFastRoamingVoipPercentage 1.3.6.1.4.1.14179.2.3.3.1.30
Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
OBJECT-TYPE    
  INTEGER zero(1), twentyfive(2), fifty(3), seventyfive(4), hundred(5)  

bsnGlobalDot11a80211eMaxBandwidth 1.3.6.1.4.1.14179.2.3.3.1.31
This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11a network. The value of this attribute can vary from 0 to 100.
OBJECT-TYPE    
  INTEGER 0..100  

bsnGlobalDot11aDTPCSupport 1.3.6.1.4.1.14179.2.3.3.1.32
This attribute may be used to enable the DTPC support on all 802.11a radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11aPhy 1.3.6.1.4.1.14179.2.3.3.2
OBJECT IDENTIFIER    

bsnGlobalDot11aMediumOccupancyLimit 1.3.6.1.4.1.14179.2.3.3.2.1
This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
OBJECT-TYPE    
  INTEGER 0..1000  

bsnGlobalDot11aCFPPeriod 1.3.6.1.4.1.14179.2.3.3.2.2
The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..255  

bsnGlobalDot11aCFPMaxDuration 1.3.6.1.4.1.14179.2.3.3.2.3
The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnGlobalDot11aCFPollable 1.3.6.1.4.1.14179.2.3.3.2.5
When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11aCFPollRequest 1.3.6.1.4.1.14179.2.3.3.2.6
Specifies whether CFP
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11aDTIMPeriod 1.3.6.1.4.1.14179.2.3.3.2.7
This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aMaximumTransmitPowerLevel 1.3.6.1.4.1.14179.2.3.3.2.8
This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aFirstChannelNumber 1.3.6.1.4.1.14179.2.3.3.2.9
This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aNumberofChannels 1.3.6.1.4.1.14179.2.3.3.2.10
This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aRTSThreshold 1.3.6.1.4.1.14179.2.3.3.2.11
This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
OBJECT-TYPE    
  INTEGER 0..2347  

bsnGlobalDot11aShortRetryLimit 1.3.6.1.4.1.14179.2.3.3.2.12
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aLongRetryLimit 1.3.6.1.4.1.14179.2.3.3.2.13
This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
OBJECT-TYPE    
  INTEGER 1..255  

bsnGlobalDot11aFragmentationThreshold 1.3.6.1.4.1.14179.2.3.3.2.14
This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
OBJECT-TYPE    
  INTEGER 256..2346  

bsnGlobalDot11aMaxTransmitMSDULifetime 1.3.6.1.4.1.14179.2.3.3.2.15
The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11aMaxReceiveLifetime 1.3.6.1.4.1.14179.2.3.3.2.16
The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

bsnGlobalDot11aTIThreshold 1.3.6.1.4.1.14179.2.3.3.2.17
The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
OBJECT-TYPE    
  Integer32  

bsnGlobalDot11aChannelAgilityEnabled 1.3.6.1.4.1.14179.2.3.3.2.18
This attribute indicates that the PHY channel agility functionality is enabled.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnGlobalDot11h 1.3.6.1.4.1.14179.2.3.4
OBJECT IDENTIFIER    

bsnGlobalDot11hConfig 1.3.6.1.4.1.14179.2.3.4.1
OBJECT IDENTIFIER    

bsnGlobalDot11hPowerConstraint 1.3.6.1.4.1.14179.2.3.4.1.1
Local maximum transmit power for a channel is defined as maximum transmit power level specified for the channel in the Country element minus the local power constraint specified for the channel in the Power Constraint element.The power constraint is coded as an unsigned integer in units of decibels. To disable power constraint set Power Constraint to 0.
OBJECT-TYPE    
  INTEGER 0..30  

bsnGlobalDot11hChannelSwitchEnable 1.3.6.1.4.1.14179.2.3.4.1.2
To enable or disable channel switch. When disabling Channel Switch no need to pass mode and count
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnGlobalDot11hChannelSwitchMode 1.3.6.1.4.1.14179.2.3.4.1.3
The Channel Switch Mode indicates any restriction on transmission until a channel switch. An Channel mode set to 1 means that the STA in a BSS to which the frame containing the element is addressed shall tranmit no further frames with in the BSS until the scheduled channel switch. A Channel switch mode set to 0 does not impose any requirement on the receiving STA.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRrm 1.3.6.1.4.1.14179.2.4
OBJECT IDENTIFIER    

bsnRrmDot11a 1.3.6.1.4.1.14179.2.4.1
OBJECT IDENTIFIER    

bsnRrmDot11aGroup 1.3.6.1.4.1.14179.2.4.1.1
OBJECT IDENTIFIER    

bsnRrmDot11aGlobalAutomaticGrouping 1.3.6.1.4.1.14179.2.4.1.1.1
Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switches form groups and elect leaders to perform better dynamic parameter optimization.
OBJECT-TYPE    
  INTEGER automatic(1), off(2)  

bsnRrmDot11aGroupLeaderMacAddr 1.3.6.1.4.1.14179.2.4.1.1.2
This is the MAC address of the group leader for the dot11a group containing this Airespace Switch.
OBJECT-TYPE    
  MacAddress  

bsnRrmIsDot11aGroupLeader 1.3.6.1.4.1.14179.2.4.1.1.3
If this Airespace Switch is a Dot11a Group Leader then this attribute will be true else it will be false.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRrmDot11aGroupLastUpdateTime 1.3.6.1.4.1.14179.2.4.1.1.4
Last time the dot11a grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.
OBJECT-TYPE    
  Unsigned32  

bsnRrmDot11aGlobalGroupInterval 1.3.6.1.4.1.14179.2.4.1.1.5
When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.
OBJECT-TYPE    
  Unsigned32  

bsnWrasDot11aGroupTable 1.3.6.1.4.1.14179.2.4.1.1.9
This is a table of Airespace Switch addresses that identifies the members of the Dot11a RF group containing this Airespace Switch. Max size is 20 entries.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasDot11aGroupEntry

bsnWrasDot11aGroupEntry 1.3.6.1.4.1.14179.2.4.1.1.9.1
...
OBJECT-TYPE    
  BsnWrasDot11aGroupEntry  

bsnWrasDot11aPeerMacAddress 1.3.6.1.4.1.14179.2.4.1.1.9.1.1
The MAC address of the member Switch.
OBJECT-TYPE    
  MacAddress  

bsnWrasDot11aPeerIpAddress 1.3.6.1.4.1.14179.2.4.1.1.9.1.21
The IP address of the Airespace Switch.
OBJECT-TYPE    
  IpAddress  

bsnRrmDot11aAPDefault 1.3.6.1.4.1.14179.2.4.1.6
OBJECT IDENTIFIER    

bsnRrmDot11aForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.4.1.6.1
foreign 802.11A interference threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aForeignNoiseThreshold 1.3.6.1.4.1.14179.2.4.1.6.2
802.11A foreign noise threshold between -127 and 0 dBm.
OBJECT-TYPE    
  INTEGER -127..0  

bsnRrmDot11aRFUtilizationThreshold 1.3.6.1.4.1.14179.2.4.1.6.3
802.11A RF utlization threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aThroughputThreshold 1.3.6.1.4.1.14179.2.4.1.6.4
802.11A throughput threshold between 1000 and 100000
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnRrmDot11aMobilesThreshold 1.3.6.1.4.1.14179.2.4.1.6.5
802.11A mobiles threshold between 1 and 75
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11aCoverageThreshold 1.3.6.1.4.1.14179.2.4.1.6.6
802.11A coverage threshold between 3 and 50.
OBJECT-TYPE    
  INTEGER 3..50  

bsnRrmDot11aMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.4.1.6.7
802.11A mobile minimum exception level between 1 and 75
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11aCoverageExceptionLevel 1.3.6.1.4.1.14179.2.4.1.6.8
802.11A coverage exception level between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11aSignalMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.9
This interval (in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aNoiseMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.10
This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aLoadMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.11
This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aCoverageMeasurementInterval 1.3.6.1.4.1.14179.2.4.1.6.12
This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11aChannelMonitorList 1.3.6.1.4.1.14179.2.4.1.6.13
This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
OBJECT-TYPE    
  INTEGER all(1), country(2), dca(3)  

bsnRrmDot11aSetFactoryDefault 1.3.6.1.4.1.14179.2.4.1.7
When set to activate all rrm parameters are reset to factory defaults
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnRrmDot11b 1.3.6.1.4.1.14179.2.4.2
OBJECT IDENTIFIER    

bsnRrmDot11bGroup 1.3.6.1.4.1.14179.2.4.2.1
OBJECT IDENTIFIER    

bsnRrmDot11bGlobalAutomaticGrouping 1.3.6.1.4.1.14179.2.4.2.1.1
Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switchs form groups and elect leaders to perform better dynamic parameter optimization.
OBJECT-TYPE    
  INTEGER automatic(1), off(2)  

bsnRrmDot11bGroupLeaderMacAddr 1.3.6.1.4.1.14179.2.4.2.1.2
This is the MAC address of the group leader for the dot11b group containing this Airespace Switch.
OBJECT-TYPE    
  MacAddress  

bsnRrmIsDot11bGroupLeader 1.3.6.1.4.1.14179.2.4.2.1.3
If this Airespace Switch is a Dot11b Group Leader then this attribute will be true else it will be false.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnRrmDot11bGroupLastUpdateTime 1.3.6.1.4.1.14179.2.4.2.1.4
Last time the dot11b grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.
OBJECT-TYPE    
  Unsigned32  

bsnRrmDot11bGlobalGroupInterval 1.3.6.1.4.1.14179.2.4.2.1.5
When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.
OBJECT-TYPE    
  Unsigned32  

bsnWrasDot11bGroupTable 1.3.6.1.4.1.14179.2.4.2.1.9
This is a table of Airespace Switch addresses that identifies the members of the Dot11b RF group containing this Airespace Switch. Max size is 20 entries.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasDot11bGroupEntry

bsnWrasDot11bGroupEntry 1.3.6.1.4.1.14179.2.4.2.1.9.1
...
OBJECT-TYPE    
  BsnWrasDot11bGroupEntry  

bsnWrasDot11bPeerMacAddress 1.3.6.1.4.1.14179.2.4.2.1.9.1.1
The MAC address of the GIGE interface.
OBJECT-TYPE    
  MacAddress  

bsnWrasDot11bPeerIpAddress 1.3.6.1.4.1.14179.2.4.2.1.9.1.21
The IP address of the Airespace Switch.
OBJECT-TYPE    
  IpAddress  

bsnRrmDot11bAPDefault 1.3.6.1.4.1.14179.2.4.2.6
OBJECT IDENTIFIER    

bsnRrmDot11bForeignInterferenceThreshold 1.3.6.1.4.1.14179.2.4.2.6.1
Foreign 802.11A interference threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bForeignNoiseThreshold 1.3.6.1.4.1.14179.2.4.2.6.2
802.11A foreign noise threshold between -127 and 0 dBm.
OBJECT-TYPE    
  INTEGER -127..0  

bsnRrmDot11bRFUtilizationThreshold 1.3.6.1.4.1.14179.2.4.2.6.3
802.11A RF utlization threshold between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bThroughputThreshold 1.3.6.1.4.1.14179.2.4.2.6.4
802.11A Airespace AP data-rate threshold between 1000 and 100000
OBJECT-TYPE    
  Unsigned32 1000..1000000  

bsnRrmDot11bMobilesThreshold 1.3.6.1.4.1.14179.2.4.2.6.5
802.11A Airespace AP mobiles threshold between 1 and 75
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11bCoverageThreshold 1.3.6.1.4.1.14179.2.4.2.6.6
802.11A Airespace AP coverage threshold between 3 and 50.
OBJECT-TYPE    
  INTEGER 3..50  

bsnRrmDot11bMobileMinExceptionLevel 1.3.6.1.4.1.14179.2.4.2.6.7
802.11A Airespace AP mobile minimum exception level between 1 and 75
OBJECT-TYPE    
  INTEGER 1..75  

bsnRrmDot11bCoverageExceptionLevel 1.3.6.1.4.1.14179.2.4.2.6.8
802.11A Airespace AP coverage exception level between 0 and 100 percent.
OBJECT-TYPE    
  INTEGER 0..100  

bsnRrmDot11bSignalMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.9
This interval( in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bNoiseMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.10
This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bLoadMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.11
This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 60..3600  

bsnRrmDot11bCoverageMeasurementInterval 1.3.6.1.4.1.14179.2.4.2.6.12
This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
OBJECT-TYPE    
  Unsigned32 10..3600  

bsnRrmDot11bChannelMonitorList 1.3.6.1.4.1.14179.2.4.2.6.13
This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
OBJECT-TYPE    
  INTEGER all(1), country(2), dca(3)  

bsnRrmDot11bSetFactoryDefault 1.3.6.1.4.1.14179.2.4.2.7
When set to activate all rrm parameters are reset to factory defaults
OBJECT-TYPE    
  INTEGER default(0), activate(1)  

bsnAAA 1.3.6.1.4.1.14179.2.5
OBJECT IDENTIFIER    

bsnRadiusAuthServerTable 1.3.6.1.4.1.14179.2.5.1
The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAuthServerEntry

bsnRadiusAuthServerEntry 1.3.6.1.4.1.14179.2.5.1.1
An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret.
OBJECT-TYPE    
  BsnRadiusAuthServerEntry  

bsnRadiusAuthServerIndex 1.3.6.1.4.1.14179.2.5.1.1.1
A number uniquely identifying each RADIUS Authentication server with which this client communicates.
OBJECT-TYPE    
  Integer32 1..17  

bsnRadiusAuthServerAddress 1.3.6.1.4.1.14179.2.5.1.1.2
The IP address of the RADIUS authentication server referred to in this table entry.
OBJECT-TYPE    
  IpAddress  

bsnRadiusAuthClientServerPortNumber 1.3.6.1.4.1.14179.2.5.1.1.3
The UDP port the client is using to send requests to this server.
OBJECT-TYPE    
  Integer32 0..65535  

bsnRadiusAuthServerKey 1.3.6.1.4.1.14179.2.5.1.1.4
The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAuthServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAuthServerKeyFormat is Ascii it can have max length of 64 bytes.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

bsnRadiusAuthServerStatus 1.3.6.1.4.1.14179.2.5.1.1.5
Server enable or disable status.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerKeyFormat 1.3.6.1.4.1.14179.2.5.1.1.6
Format of the server key. When hex, the number of characters in the key should be even.
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAuthServerRFC3576 1.3.6.1.4.1.14179.2.5.1.1.7
Support for Dynamic Authorization Extensions to RADIUS.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerIPSec 1.3.6.1.4.1.14179.2.5.1.1.8
IPSec over RADIUS
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerIPSecAuth 1.3.6.1.4.1.14179.2.5.1.1.9
The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAuthServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER none(0), hmacMd5(1), hmacSha1(2)  

bsnRadiusAuthServerIPSecEncryption 1.3.6.1.4.1.14179.2.5.1.1.10
The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAuthServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER none(0), des(1), tripleDes(2), aesCbc(3)  

bsnRadiusAuthServerIPSecIKEPhase1 1.3.6.1.4.1.14179.2.5.1.1.11
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAuthServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER main(1), agressive(2)  

bsnRadiusAuthServerIPSecIKELifetime 1.3.6.1.4.1.14179.2.5.1.1.12
IPSec IKE's Lifetime. This applies only when bsnRadiusAuthServerIPSec is in enable state.
OBJECT-TYPE    
  Integer32 1800..345600  

bsnRadiusAuthServerIPSecDHGroup 1.3.6.1.4.1.14179.2.5.1.1.13
IKE's Diffie-Hellman Group. This applies only when bsnRadiusAuthServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER group1(1), group2(2), group5(5)  

bsnRadiusAuthServerNetworkUserConfig 1.3.6.1.4.1.14179.2.5.1.1.14
When enabled, this entry is considered as network user radius authenticating server entry.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerMgmtUserConfig 1.3.6.1.4.1.14179.2.5.1.1.15
When enabled, this entry is considered as management user radius authenticating server entry.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAuthServerRetransmitTimeout 1.3.6.1.4.1.14179.2.5.1.1.17
Time in seconds after which a radius authentication request will timeout and a retransmission will be taken up by the switch.
OBJECT-TYPE    
  INTEGER 2..30  

bsnRadiusAuthServerKeyWrapKEKkey 1.3.6.1.4.1.14179.2.5.1.1.18
Key-encryption-key (KEK) used as the key for the 128 bit AES Key Wrap algorithm to encrypt the PMK in the key attribute. If the key is present in request, it should be taken as a hint by the server that the sender prefers this method of encryption over others. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is retunred. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 16 bytes in length. if the format chosen is hex then it should be 32 bytes in length.
OBJECT-TYPE    
  OCTET STRING  

bsnRadiusAuthServerKeyWrapMACKkey 1.3.6.1.4.1.14179.2.5.1.1.19
Message-authenticator-code-key ( MACK) - used as the key for the HMAC-SHA-1 algorithm to sign the RADIUS message to prevent spoofing. MACK must be configured when KEK is configured. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is returned. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 20 bytes in length. If the format chosen is hex then it should be 40 bytes in length.
OBJECT-TYPE    
  OCTET STRING  

bsnRadiusAuthServerKeyWrapFormat 1.3.6.1.4.1.14179.2.5.1.1.20
Format for the Key Wrap keys. This object is mandatory for manager to send if the key Wrap keys are being configured. Get on this object will always return hex(1)
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAuthServerRowStatus 1.3.6.1.4.1.14179.2.5.1.1.26
Row Status for creation/deletion
OBJECT-TYPE    
  RowStatus  

bsnRadiusAccServerTable 1.3.6.1.4.1.14179.2.5.2
The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAccServerEntry

bsnRadiusAccServerEntry 1.3.6.1.4.1.14179.2.5.2.1
An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
OBJECT-TYPE    
  BsnRadiusAccServerEntry  

bsnRadiusAccServerIndex 1.3.6.1.4.1.14179.2.5.2.1.1
A number uniquely identifying each RADIUS Accounting server with which this client communicates.
OBJECT-TYPE    
  Integer32 1..17  

bsnRadiusAccServerAddress 1.3.6.1.4.1.14179.2.5.2.1.2
The IP address of the RADIUS accounting server referred to in this table entry.
OBJECT-TYPE    
  IpAddress  

bsnRadiusAccClientServerPortNumber 1.3.6.1.4.1.14179.2.5.2.1.3
The UDP port the client is using to send requests to this server.
OBJECT-TYPE    
  Integer32 0..65535  

bsnRadiusAccServerKey 1.3.6.1.4.1.14179.2.5.2.1.4
The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAccServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAccServerKeyFormat is Ascii it can have max length of 64 bytes.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

bsnRadiusAccServerStatus 1.3.6.1.4.1.14179.2.5.2.1.5
Server enable or disable status.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerKeyFormat 1.3.6.1.4.1.14179.2.5.2.1.6
Format of the server key. When hex, the number of characters in the key should be even.
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

bsnRadiusAccServerIPSec 1.3.6.1.4.1.14179.2.5.2.1.7
IPSec over RADIUS
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerIPSecAuth 1.3.6.1.4.1.14179.2.5.2.1.8
The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAccServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER none(0), hmacMd5(1), hmacSha1(2)  

bsnRadiusAccServerIPSecEncryption 1.3.6.1.4.1.14179.2.5.2.1.9
The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAccServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER none(0), des(1), tripleDes(2), aesCbc(3)  

bsnRadiusAccServerIPSecIKEPhase1 1.3.6.1.4.1.14179.2.5.2.1.10
VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAccServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER main(1), agressive(2)  

bsnRadiusAccServerIPSecIKELifetime 1.3.6.1.4.1.14179.2.5.2.1.11
IPSec IKE's Lifetime. This applies only when bsnRadiusAccServerIPSec is in enable state.
OBJECT-TYPE    
  Integer32 1800..345600  

bsnRadiusAccServerIPSecDHGroup 1.3.6.1.4.1.14179.2.5.2.1.12
IKE's Diffie-Hellman Group. This applies only when bsnRadiusAccServerIPSec is in enable state.
OBJECT-TYPE    
  INTEGER group1(1), group2(2), group5(5)  

bsnRadiusAccServerNetworkUserConfig 1.3.6.1.4.1.14179.2.5.2.1.13
When enabled, this entry is considered as network user radius accounting server entry.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRadiusAccServerRetransmitTimeout 1.3.6.1.4.1.14179.2.5.2.1.14
Time in seconds after which a radius accounting request will timeout and a retransmission will be taken up by the switch.
OBJECT-TYPE    
  INTEGER 2..30  

bsnRadiusAccServerRowStatus 1.3.6.1.4.1.14179.2.5.2.1.26
Row Status for creation/deletion
OBJECT-TYPE    
  RowStatus  

bsnRadiusAuthServerStatsTable 1.3.6.1.4.1.14179.2.5.3
The listing the Statistics of RADIUS authentication servers.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAuthServerStatsEntry

bsnRadiusAuthServerStatsEntry 1.3.6.1.4.1.14179.2.5.3.1
An entry representing statistics a RADIUS authentication server with which the client shares a secret.
OBJECT-TYPE    
  BsnRadiusAuthServerStatsEntry  

bsnRadiusAuthClientRoundTripTime 1.3.6.1.4.1.14179.2.5.3.1.6
The time interval (in hundredths of a second) between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.
OBJECT-TYPE    
  TimeTicks  

bsnRadiusAuthClientAccessRequests 1.3.6.1.4.1.14179.2.5.3.1.7
The number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessRetransmissions 1.3.6.1.4.1.14179.2.5.3.1.8
The number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessAccepts 1.3.6.1.4.1.14179.2.5.3.1.9
The number of RADIUS Access-Accept packets (valid or invalid) received from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessRejects 1.3.6.1.4.1.14179.2.5.3.1.10
The number of RADIUS Access-Reject packets (valid or invalid) received from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientAccessChallenges 1.3.6.1.4.1.14179.2.5.3.1.11
The number of RADIUS Access-Challenge packets (valid or invalid) received from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientMalformedAccessResponses 1.3.6.1.4.1.14179.2.5.3.1.12
The number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators or Signature attributes or unknown types are not included as malformed access responses.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientBadAuthenticators 1.3.6.1.4.1.14179.2.5.3.1.13
The number of RADIUS Access-Response packets containing invalid authenticators or Signature attributes received from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientPendingRequests 1.3.6.1.4.1.14179.2.5.3.1.14
The number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Access-Request is sent and decremented due to receipt of an Acess-Accept, Access-Reject or Access-Challenge, a timeout or retransmission.
OBJECT-TYPE    
  Gauge32  

bsnRadiusAuthClientTimeouts 1.3.6.1.4.1.14179.2.5.3.1.15
The number of authentication timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientUnknownTypes 1.3.6.1.4.1.14179.2.5.3.1.16
The number of RADIUS packets of unknown type which were received from this server on the authentication port.
OBJECT-TYPE    
  Counter32  

bsnRadiusAuthClientPacketsDropped 1.3.6.1.4.1.14179.2.5.3.1.36
The number of RADIUS packets of which were received from this server on the authentication port and dropped for some other reason.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccServerStatsTable 1.3.6.1.4.1.14179.2.5.4
The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnRadiusAccServerStatsEntry

bsnRadiusAccServerStatsEntry 1.3.6.1.4.1.14179.2.5.4.1
An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
OBJECT-TYPE    
  BsnRadiusAccServerStatsEntry  

bsnRadiusAccClientRoundTripTime 1.3.6.1.4.1.14179.2.5.4.1.6
The time interval between the most recent Accounting-Response and the Accounting-Request that matched it from this RADIUS accounting server.
OBJECT-TYPE    
  TimeTicks  

bsnRadiusAccClientRequests 1.3.6.1.4.1.14179.2.5.4.1.7
The number of RADIUS Accounting-Request packets sent. This does not include retransmissions.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientRetransmissions 1.3.6.1.4.1.14179.2.5.4.1.8
The number of RADIUS Accounting-Request packets retransmitted to this RADIUS accounting server. Retransmissions include retries where the Identifier and Acct-Delay have been updated, as well as those in which they remain the same.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientResponses 1.3.6.1.4.1.14179.2.5.4.1.9
The number of RADIUS packets received on the accounting port from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientMalformedResponses 1.3.6.1.4.1.14179.2.5.4.1.10
The number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientBadAuthenticators 1.3.6.1.4.1.14179.2.5.4.1.11
The number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientPendingRequests 1.3.6.1.4.1.14179.2.5.4.1.12
The number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when an Accounting-Request is sent and decremented due to receipt of an Accounting-Response, a timeout or a retransmission.
OBJECT-TYPE    
  Gauge32  

bsnRadiusAccClientTimeouts 1.3.6.1.4.1.14179.2.5.4.1.13
The number of accounting timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as an Accounting-Request as well as a timeout.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientUnknownTypes 1.3.6.1.4.1.14179.2.5.4.1.14
The number of RADIUS packets of unknown type which were received from this server on the accounting port.
OBJECT-TYPE    
  Counter32  

bsnRadiusAccClientPacketsDropped 1.3.6.1.4.1.14179.2.5.4.1.34
The number of RADIUS packets which were received from this server on the accounting port and dropped for some other reason.
OBJECT-TYPE    
  Counter32  

bsnUsersTable 1.3.6.1.4.1.14179.2.5.5
The (conceptual) table listing Wlan Users
OBJECT-TYPE    
  SEQUENCE OF  
    BsnUsersEntry

bsnUsersEntry 1.3.6.1.4.1.14179.2.5.5.1
....
OBJECT-TYPE    
  BsnUsersEntry  

bsnUserName 1.3.6.1.4.1.14179.2.5.5.1.2
User Name
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnUserPassword 1.3.6.1.4.1.14179.2.5.5.1.3
User Password
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnUserEssIndex 1.3.6.1.4.1.14179.2.5.5.1.4
User WLAN ID. Value 0 implies that this applies to any WLAN ID.
OBJECT-TYPE    
  INTEGER 0..17  

bsnUserAccessMode 1.3.6.1.4.1.14179.2.5.5.1.5
User Access Mode.
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

bsnUserType 1.3.6.1.4.1.14179.2.5.5.1.6
User Type.
OBJECT-TYPE    
  INTEGER management(1), wlan(2), macFilter(3)  

bsnUserInterfaceName 1.3.6.1.4.1.14179.2.5.5.1.7
Interface Name.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnUserRowStatus 1.3.6.1.4.1.14179.2.5.5.1.26
Row Status
OBJECT-TYPE    
  RowStatus  

bsnBlackListClientTable 1.3.6.1.4.1.14179.2.5.6
The table listing Wlan Black Listed Clients
OBJECT-TYPE    
  SEQUENCE OF  
    BsnBlackListClientEntry

bsnBlackListClientEntry 1.3.6.1.4.1.14179.2.5.6.1
....
OBJECT-TYPE    
  BsnBlackListClientEntry  

bsnBlackListClientMacAddress 1.3.6.1.4.1.14179.2.5.6.1.1
Black Listed Client MAC Address
OBJECT-TYPE    
  OCTET STRING SIZE(1..12)  

bsnBlackListClientDescription 1.3.6.1.4.1.14179.2.5.6.1.2
Black Listed Client Description
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnBlackListClientRowStatus 1.3.6.1.4.1.14179.2.5.6.1.22
Row Status
OBJECT-TYPE    
  RowStatus  

bsnAclTable 1.3.6.1.4.1.14179.2.5.7
The table listing ACLs (Access Control Lists) on the Switch.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAclEntry

bsnAclEntry 1.3.6.1.4.1.14179.2.5.7.1
....
OBJECT-TYPE    
  BsnAclEntry  

bsnAclName 1.3.6.1.4.1.14179.2.5.7.1.1
Name of the Access Control List.
OBJECT-TYPE    
  OCTET STRING SIZE(1..32)  

bsnAclApplyMode 1.3.6.1.4.1.14179.2.5.7.1.2
The apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch.
OBJECT-TYPE    
  INTEGER notapplied(0), applied(1)  

bsnAclRowStatus 1.3.6.1.4.1.14179.2.5.7.1.20
Row Status of the ACL.
OBJECT-TYPE    
  RowStatus  

bsnAclRuleTable 1.3.6.1.4.1.14179.2.5.8
The table listing Acl Rules(Access Control List Entries) on the ACL with name bsnAclName.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAclRuleEntry

bsnAclRuleEntry 1.3.6.1.4.1.14179.2.5.8.1
....
OBJECT-TYPE    
  BsnAclRuleEntry  

bsnAclRuleIndex 1.3.6.1.4.1.14179.2.5.8.1.2
Index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.
OBJECT-TYPE    
  Unsigned32 1..64  

bsnAclRuleAction 1.3.6.1.4.1.14179.2.5.8.1.3
The permission mode of a rule.
OBJECT-TYPE    
  INTEGER deny(0), permit(1)  

bsnAclRuleDirection 1.3.6.1.4.1.14179.2.5.8.1.4
The direction of the packet to which the rule may be applied.
OBJECT-TYPE    
  INTEGER inbound(0), outbound(1), any(2)  

bsnAclRuleSourceIpAddress 1.3.6.1.4.1.14179.2.5.8.1.5
Source IP Address of the ACL rule. A value 0 implies any source address.
OBJECT-TYPE    
  IpAddress  

bsnAclRuleSourceIpNetmask 1.3.6.1.4.1.14179.2.5.8.1.6
Source IP Netmask of the ACL rule. A value 0 implies any source mask.
OBJECT-TYPE    
  IpAddress  

bsnAclRuleDestinationIpAddress 1.3.6.1.4.1.14179.2.5.8.1.7
Destination IP Address of the ACL rule. A value 0 implies any destination address.
OBJECT-TYPE    
  IpAddress  

bsnAclRuleDestinationIpNetmask 1.3.6.1.4.1.14179.2.5.8.1.8
Destination Netmask of the ACL rule. A value 0 implies any destination mask.
OBJECT-TYPE    
  IpAddress  

bsnAclRuleProtocol 1.3.6.1.4.1.14179.2.5.8.1.9
Protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that this rule applies to 'Any' protocol.
OBJECT-TYPE    
  Unsigned32 0..256  

bsnAclRuleStartSourcePort 1.3.6.1.4.1.14179.2.5.8.1.10
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleEndSourcePort 1.3.6.1.4.1.14179.2.5.8.1.11
Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleStartDestinationPort 1.3.6.1.4.1.14179.2.5.8.1.12
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleEndDestinationPort 1.3.6.1.4.1.14179.2.5.8.1.13
Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
OBJECT-TYPE    
  Unsigned32 0..65535  

bsnAclRuleDscp 1.3.6.1.4.1.14179.2.5.8.1.14
DSCP value of the rule. A value 256 implies Any
OBJECT-TYPE    
  Unsigned32 0..256  

bsnAclNewRuleIndex 1.3.6.1.4.1.14179.2.5.8.1.15
New Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield anything.
OBJECT-TYPE    
  Unsigned32 1..64  

bsnAclRuleRowStatus 1.3.6.1.4.1.14179.2.5.8.1.40
Row Status of the ACL Rule.
OBJECT-TYPE    
  RowStatus  

bsnMacFilterTable 1.3.6.1.4.1.14179.2.5.9
The table listing MAC Filter entries
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMacFilterEntry

bsnMacFilterEntry 1.3.6.1.4.1.14179.2.5.9.1
....
OBJECT-TYPE    
  BsnMacFilterEntry  

bsnMacFilterAddress 1.3.6.1.4.1.14179.2.5.9.1.1
MAC Address of the entry
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnMacFilterWlanId 1.3.6.1.4.1.14179.2.5.9.1.2
WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
OBJECT-TYPE    
  INTEGER 0..17  

bsnMacFilterInterfaceName 1.3.6.1.4.1.14179.2.5.9.1.3
Interface Name.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnMacFilterDescription 1.3.6.1.4.1.14179.2.5.9.1.4
Description of the MAC Filter entry.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnMacFilterRowStatus 1.3.6.1.4.1.14179.2.5.9.1.24
Row Status
OBJECT-TYPE    
  RowStatus  

bsnLocalNetUserTable 1.3.6.1.4.1.14179.2.5.10
The table listing Local Net User entries.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLocalNetUserEntry

bsnLocalNetUserEntry 1.3.6.1.4.1.14179.2.5.10.1
....
OBJECT-TYPE    
  BsnLocalNetUserEntry  

bsnLocalNetUserName 1.3.6.1.4.1.14179.2.5.10.1.1
Name of the net user.
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnLocalNetUserWlanId 1.3.6.1.4.1.14179.2.5.10.1.2
WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
OBJECT-TYPE    
  INTEGER 0..17  

bsnLocalNetUserPassword 1.3.6.1.4.1.14179.2.5.10.1.3
User Password.
OBJECT-TYPE    
  OCTET STRING SIZE(0..24)  

bsnLocalNetUserDescription 1.3.6.1.4.1.14179.2.5.10.1.4
Description of the Net User entry.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnLocalNetUserLifetime 1.3.6.1.4.1.14179.2.5.10.1.5
This object indicates the lifetime of an user account expressed in hundredths of a second. Lifetime period other than 0 will make it a guest-user. Minimum value for guest user is 60 seconds (6000). Once configured as non-guest user can not be change to guest user and vice-versa. Default value is for a day and max lifetime is 259200000(30 days). WLANIds, which have webauth policy are valid for guest access user.
OBJECT-TYPE    
  TimeInterval 0 | 6000..259200000  

bsnLocalNetUserStartTime 1.3.6.1.4.1.14179.2.5.10.1.6
This object indicates the time when the guest user account was created and expressed as the number of seconds elapsed since 1st Jan, 1970.
OBJECT-TYPE    
  TimeTicks  

bsnLocalNetUserRemainingTime 1.3.6.1.4.1.14179.2.5.10.1.7
This object indicates the remaining session time for the guest user in hundredths of a second.
OBJECT-TYPE    
  TimeInterval  

bsnLocalNetUserRowStatus 1.3.6.1.4.1.14179.2.5.10.1.24
Row Status
OBJECT-TYPE    
  RowStatus  

bsnLocalManagementUserTable 1.3.6.1.4.1.14179.2.5.11
The (conceptual) table listing Local Management Users
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLocalManagementUserEntry

bsnLocalManagementUserEntry 1.3.6.1.4.1.14179.2.5.11.1
....
OBJECT-TYPE    
  BsnLocalManagementUserEntry  

bsnLocalManagementUserName 1.3.6.1.4.1.14179.2.5.11.1.1
User Name
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnLocalManagementUserPassword 1.3.6.1.4.1.14179.2.5.11.1.2
User Password
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnLocalManagementUserAccessMode 1.3.6.1.4.1.14179.2.5.11.1.3
User Access Mode.
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

bsnLocalManagementUserRowStatus 1.3.6.1.4.1.14179.2.5.11.1.23
Row Status
OBJECT-TYPE    
  RowStatus  

bsnRadiusAuthKeyWrapEnable 1.3.6.1.4.1.14179.2.5.12
When keyWrap is enable then for 801.1X and 802.11i client Authentication, request is sent to those radius servers which has KEK and MACK keys are configured. Radius servers are widely used for user authentications. In 802.11i and 802.1X type authentication, the controller recives Pairwise Master KEy(PMK) from RADIUS sever using vendor specific RADIUS attributes, which uses MPPE RFC3078. Since MPPE uses RC4 algorithm to provide data confidentiality, it is not FIPS approved. For this RADIUS key WRAP attributes, bsnRadiusAuthServerKeyWrap and bsnRadiusAuthServerKeyWrapMACKkey have been added, which are used to securely transfer encryption keys using non-proprietary techniques.
OBJECT-TYPE    
  TruthValue  

bsnRadiusAuthCacheCredentialsLocally 1.3.6.1.4.1.14179.2.5.14
Enable or disable caching of credentials locally for RADIUS Auth servers. This is used when a client uses a one time password authentication scheme.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAAAMacDelimiter 1.3.6.1.4.1.14179.2.5.15
The delimiter to be used for mac filtering. It can be colon as in xx:xx:xx:xx:xx:xx or hyphen as in xx-xx-xx-xx-xx-xx or single hyphen as in xxxxxx-xxxxxx or no delimiter as in xxxxxxxxxxxx.
OBJECT-TYPE    
  INTEGER noDelimiter(0), colon(1), hyphen(2), singleHyphen(3)  

bsnAAARadiusCompatibilityMode 1.3.6.1.4.1.14179.2.5.16
The required compatibility mode for MAC filtering. For ciscoACS, the expected MAC delimiter setting is colon and for orinocoRadius, it is singleHyphen.
OBJECT-TYPE    
  INTEGER ciscoACS(0), orinocoRadius(1), other(2)  

bsnAAARadiusCallStationIdType 1.3.6.1.4.1.14179.2.5.17
This attribute configures the call station ID information sent in RADIUS messages. The value undefined cannot be set during the write operation.
OBJECT-TYPE    
  INTEGER ipAddr(0), macAddr(1), apMacAddress(2)  

bsnExternalPolicyServerAclName 1.3.6.1.4.1.14179.2.5.18
This attribute configures the ACL Name for External Policy Servers
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

bsnExternalPolicyServerTable 1.3.6.1.4.1.14179.2.5.19
The (conceptual) table listing the External Policy servers with which client share a secret.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnExternalPolicyServerEntry

bsnExternalPolicyServerEntry 1.3.6.1.4.1.14179.2.5.19.1
An entry (conceptual row) representing an External policy server with which the client shares a secret.
OBJECT-TYPE    
  BsnExternalPolicyServerEntry  

bsnExternalPolicyServerIndex 1.3.6.1.4.1.14179.2.5.19.1.1
A number uniquely identifying each External Policy server with which this client communicates.
OBJECT-TYPE    
  Integer32 0..2  

bsnExternalPolicyServerAddress 1.3.6.1.4.1.14179.2.5.19.1.2
The IP address of the External Policy server referred to in this table entry.
OBJECT-TYPE    
  IpAddress  

bsnExternalPolicyServerPortNumber 1.3.6.1.4.1.14179.2.5.19.1.3
The UDP port the client is using to send requests to this server.
OBJECT-TYPE    
  Integer32 0..65535  

bsnExternalPolicyServerKey 1.3.6.1.4.1.14179.2.5.19.1.4
The authentication and encryption key shared between the client and this External Policy Server.
OBJECT-TYPE    
  OCTET STRING SIZE(0..16)  

bsnExternalPolicyServerAdminStatus 1.3.6.1.4.1.14179.2.5.19.1.5
Server enable or disable status.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnExternalPolicyServerConnectionStatus 1.3.6.1.4.1.14179.2.5.19.1.6
Server enable or disable status.
OBJECT-TYPE    
  INTEGER disconnected(0), connected(1)  

bsnExternalPolicyServerRowStatus 1.3.6.1.4.1.14179.2.5.19.1.26
Row Status for creation/deletion
OBJECT-TYPE    
  RowStatus  

bsnAAALocalDatabaseSize 1.3.6.1.4.1.14179.2.5.20
This attribute is the total number of entries permitted in the local users database. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklistclients and the MAC Filters. If the database size limit is reached, no more entries in any of these user lists are allowed to be created. To continue creating more entries, one should increase the size of the database. This value is applied on reboot and then matches the bsnAACurrentLocalDatabaseSize.
OBJECT-TYPE    
  Integer32 512..2048  

bsnAAACurrentLocalDatabaseSize 1.3.6.1.4.1.14179.2.5.21
This attribute is the maximum number of entries in the local users database that is effective currently. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklist clients) and the MAC Filters.
OBJECT-TYPE    
  Integer32 512..2048  

bsnAPAuthorizationTable 1.3.6.1.4.1.14179.2.5.22
The table listing AP Authorization entries
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPAuthorizationEntry

bsnAPAuthorizationEntry 1.3.6.1.4.1.14179.2.5.22.1
BsnAPAuthorizationEntry
OBJECT-TYPE    
  BsnAPAuthorizationEntry  

bsnAPAuthMacAddress 1.3.6.1.4.1.14179.2.5.22.1.1
MAC Address of the AP entry
OBJECT-TYPE    
  OCTET STRING SIZE(1..24)  

bsnAPAuthCertificateType 1.3.6.1.4.1.14179.2.5.22.1.2
Supported certificate types are MIC and SSC (Self-Signed-Certificate).
OBJECT-TYPE    
  INTEGER unknown(0), mic(1), ssc(2)  

bsnAPAuthHashKey 1.3.6.1.4.1.14179.2.5.22.1.3
SHA1 hash key for SSC certificate validation. It has to be 40 hexa-decimal characters. This is considered when certificate type is SSC.
OBJECT-TYPE    
  OCTET STRING SIZE(0..40)  

bsnAPAuthRowStatus 1.3.6.1.4.1.14179.2.5.22.1.20
Row Status
OBJECT-TYPE    
  RowStatus  

bsnTrap 1.3.6.1.4.1.14179.2.6
OBJECT IDENTIFIER    

bsnTrapControl 1.3.6.1.4.1.14179.2.6.1
OBJECT IDENTIFIER    

bsnDot11StationTrapControlMask 1.3.6.1.4.1.14179.2.6.1.1
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurence. Event corresponding bit ----- ----------------- bsnDot11StationDisassociate 1 bsnDot11StationDeauthenticate 2 bsnDot11StationAuthenticateFail 4 bsnDot11StationAssociateFail 8 bsnDot11StationBlacklisted 16 By Default all bits are off.
OBJECT-TYPE    
  Unsigned32  

bsnAPTrapControlMask 1.3.6.1.4.1.14179.2.6.1.2
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnAPAssociate/Disassociate 1 bsnAPIfUp/Down 4 By Default all bits are on.
OBJECT-TYPE    
  Unsigned32  

bsnAPProfileTrapControlMask 1.3.6.1.4.1.14179.2.6.1.3
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- LoadProfileFail 1 NoiseProfileFail 2 InterferenceProfileFail 4 CoverageProfileFailed 8
OBJECT-TYPE    
  Unsigned32  

bsnAPParamUpdateTrapControlMask 1.3.6.1.4.1.14179.2.6.1.4
Mac Parameters are updated for a Airespace AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- TxPowerChange 1 ChannelChange 2 AntennaChange 4 RTSCTSThresholdChange 8 EDThresholdChange 16 FragmentationThresholdChange 32
OBJECT-TYPE    
  Unsigned32  

bsnIpsecTrapsMask 1.3.6.1.4.1.14179.2.6.1.5
This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnIpsecEspAuthFailureTrap 1 bsnIpsecEspReplayFailureTrap 2 bsnIpsecEspPolicyFailureTrap 4 bsnIpsecEspInvalidSpiTrap 8 bsnIpsecOtherPolicyFailureTrap 16 bsnIpsecIkeNegFailure 32 bsnIpsecSuiteNegFailure 64 bsnIpsecInvalidCookieTrap 128
OBJECT-TYPE    
  Unsigned32  

bsnRogueAPTrapEnable 1.3.6.1.4.1.14179.2.6.1.6
If Rogue AP Detection and Removed Traps need to be sent
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnRADIUSServerTrapEnable 1.3.6.1.4.1.14179.2.6.1.7
if RADIUS Server Traps need to be sent
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAuthenticationFailureTrapEnable 1.3.6.1.4.1.14179.2.6.1.8
If Authentication Failure Traps need to be sent
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnConfigSaveTrapEnable 1.3.6.1.4.1.14179.2.6.1.9
If Rogue AP Detection and Removed Traps need to be sent
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsn80211SecurityTrapControlMask 1.3.6.1.4.1.14179.2.6.1.10
This mask is for Security related trap controls. Event corresponding bit ----- ----------------- bsnWepKeyDecryptError 1 By Default all bits are off.
OBJECT-TYPE    
  Unsigned32  

bsnWpsTrapControlEnable 1.3.6.1.4.1.14179.2.6.1.11
This control is for WPS(Wireless Intrusion Protection System) related traps.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnTrapVariable 1.3.6.1.4.1.14179.2.6.2
OBJECT IDENTIFIER    

bsnAuthFailureUserName 1.3.6.1.4.1.14179.2.6.2.1
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

bsnAuthFailureUserType 1.3.6.1.4.1.14179.2.6.2.2
OBJECT-TYPE    
  INTEGER mgmtUser(1), wlanUser(2), macFilter(3)  

bsnRemoteIPv4Address 1.3.6.1.4.1.14179.2.6.2.3
OBJECT-TYPE    
  IpAddress  

bsnIpsecErrorCount 1.3.6.1.4.1.14179.2.6.2.4
OBJECT-TYPE    
  Integer32  

bsnIpsecSPI 1.3.6.1.4.1.14179.2.6.2.5
OBJECT-TYPE    
  Integer32  

bsnRemoteUdpPort 1.3.6.1.4.1.14179.2.6.2.6
OBJECT-TYPE    
  Integer32 0..65535  

bsnIkeAuthMethod 1.3.6.1.4.1.14179.2.6.2.7
OBJECT-TYPE    
  Integer32  

bsnIkeTotalInitFailures 1.3.6.1.4.1.14179.2.6.2.8
OBJECT-TYPE    
  Integer32  

bsnIkeTotalInitNoResponses 1.3.6.1.4.1.14179.2.6.2.9
OBJECT-TYPE    
  Integer32  

bsnIkeTotalRespFailures 1.3.6.1.4.1.14179.2.6.2.10
OBJECT-TYPE    
  Integer32  

bsnNotifiesSent 1.3.6.1.4.1.14179.2.6.2.11
OBJECT-TYPE    
  Integer32  

bsnNotifiesReceived 1.3.6.1.4.1.14179.2.6.2.12
OBJECT-TYPE    
  Integer32  

bsnSuiteInitFailures 1.3.6.1.4.1.14179.2.6.2.13
OBJECT-TYPE    
  Integer32  

bsnSuiteRespondFailures 1.3.6.1.4.1.14179.2.6.2.14
OBJECT-TYPE    
  Integer32  

bsnInitiatorCookie 1.3.6.1.4.1.14179.2.6.2.15
The initiator cookie used in an ISAKMP message, to be associated with a trap.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

bsnResponderCookie 1.3.6.1.4.1.14179.2.6.2.16
The responder cookie used in an ISAKMP message, to be associated with a trap.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

bsnIsakmpInvalidCookies 1.3.6.1.4.1.14179.2.6.2.17
OBJECT-TYPE    
  Integer32  

bsnCurrentRadiosCount 1.3.6.1.4.1.14179.2.6.2.18
OBJECT-TYPE    
  Integer32  

bsnLicenseRadioCount 1.3.6.1.4.1.14179.2.6.2.19
OBJECT-TYPE    
  Integer32  

bsnAPMacAddrTrapVariable 1.3.6.1.4.1.14179.2.6.2.20
OBJECT-TYPE    
  MacAddress  

bsnAPNameTrapVariable 1.3.6.1.4.1.14179.2.6.2.21
OBJECT-TYPE    
  DisplayString  

bsnAPSlotIdTrapVariable 1.3.6.1.4.1.14179.2.6.2.22
Number of Radio Interfaces on the Airespace AP.
OBJECT-TYPE    
  Integer32  

bsnAPChannelNumberTrapVariable 1.3.6.1.4.1.14179.2.6.2.23
OBJECT-TYPE    
  Integer32  

bsnAPCoverageThresholdTrapVariable 1.3.6.1.4.1.14179.2.6.2.24
OBJECT-TYPE    
  Integer32  

bsnAPCoverageFailedClients 1.3.6.1.4.1.14179.2.6.2.25
OBJECT-TYPE    
  Integer32  

bsnAPCoverageTotalClients 1.3.6.1.4.1.14179.2.6.2.26
OBJECT-TYPE    
  Integer32  

bsnClientMacAddr 1.3.6.1.4.1.14179.2.6.2.27
OBJECT-TYPE    
  MacAddress  

bsnClientRssi 1.3.6.1.4.1.14179.2.6.2.28
OBJECT-TYPE    
  Integer32  

bsnClientSnr 1.3.6.1.4.1.14179.2.6.2.29
OBJECT-TYPE    
  Integer32  

bsnInterferenceEnergyBeforeChannelUpdate 1.3.6.1.4.1.14179.2.6.2.30
OBJECT-TYPE    
  Integer32  

bsnInterferenceEnergyAfterChannelUpdate 1.3.6.1.4.1.14179.2.6.2.31
OBJECT-TYPE    
  Integer32  

bsnAPPortNumberTrapVariable 1.3.6.1.4.1.14179.2.6.2.32
OBJECT-TYPE    
  Integer32  

bsnMaxRogueCount 1.3.6.1.4.1.14179.2.6.2.33
OBJECT-TYPE    
  Integer32  

bsnStationMacAddress 1.3.6.1.4.1.14179.2.6.2.34
OBJECT-TYPE    
  MacAddress  

bsnStationAPMacAddr 1.3.6.1.4.1.14179.2.6.2.35
OBJECT-TYPE    
  MacAddress  

bsnStationAPIfSlotId 1.3.6.1.4.1.14179.2.6.2.36
OBJECT-TYPE    
  INTEGER 0..15  

bsnStationReasonCode 1.3.6.1.4.1.14179.2.6.2.37
OBJECT-TYPE    
  INTEGER unspecified(1), previousAuthNotValid(2), deauthenticationLeaving(3), disassociationDueToInactivity(4), disassociationAPBusy(5), class2FrameFromNonAuthStation(6), class2FrameFromNonAssStation(7), disassociationStaHasLeft(8), staReqAssociationWithoutAuth(9), missingReasonCode(99)  

bsnStationBlacklistingReasonCode 1.3.6.1.4.1.14179.2.6.2.38
OBJECT-TYPE    
  INTEGER failed80211Auth(1), failedAssociation(2), ipTheft(3), failed8021xAuth(4), failedWebAuth(5)  

bsnStationUserName 1.3.6.1.4.1.14179.2.6.2.39
The user name of a client. This is used for the Client Associated trap. It may be null when not known.
OBJECT-TYPE    
  DisplayString  

bsnRogueAPOnWiredNetwork 1.3.6.1.4.1.14179.2.6.2.40
This is the flag used on the bsnRogueAPDetected trap to state if the rogue is found on the wired network. Typically, after a rogue is found, there may be another bsnRogueAPDetected trap that will have the value of this flag 1 if the rogue is detected on the wired network.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnNavDosAttackSourceMacAddr 1.3.6.1.4.1.14179.2.6.2.41
MAC address generating the attack.
OBJECT-TYPE    
  MacAddress  

bsnWlanIdTrapVariable 1.3.6.1.4.1.14179.2.6.2.42
WLAN ID used by the client when the WPA MIC error counter measure was activated.
OBJECT-TYPE    
  INTEGER 1..17  

bsnUserIpAddress 1.3.6.1.4.1.14179.2.6.2.43
OBJECT-TYPE    
  IpAddress  

bsnRogueAdhocMode 1.3.6.1.4.1.14179.2.6.2.44
This is the flag used on the bsnRogueAPDetected trap to state if the rogue found is an Adhoc rogue or it is an AP.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnClearTrapVariable 1.3.6.1.4.1.14179.2.6.2.45
This is the flag is used to indicate if this is a clear trap for the original alert or not.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

bsnDuplicateIpTrapVariable 1.3.6.1.4.1.14179.2.6.2.46
This field is used on the bsnDuplicateIpAddressReported trap to contain the IP Address in question when switch or an AP detected a duplicate IP Address on another machine.
OBJECT-TYPE    
  IpAddress  

bsnDuplicateIpTrapClear 1.3.6.1.4.1.14179.2.6.2.47
This is the flag used to indicate clear state for the bsnDuplicateIpAddressReported trap.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

bsnDuplicateIpReportedByAP 1.3.6.1.4.1.14179.2.6.2.48
This is the flag used on the bsnDuplicateIpAddressReported trap to indicate whether the switch or an AP detected a duplicate IP Address on another machine.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnTrustedApRadioPolicyRequired 1.3.6.1.4.1.14179.2.6.2.49
This is the radio policy required by a trusted Rogue.
OBJECT-TYPE    
  INTEGER none(0), dot11b(1), dot11a(2), dot11bg(3)  

bsnTrustedApEncryptionUsed 1.3.6.1.4.1.14179.2.6.2.50
This is the encryption type used by a trusted Rogue.
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnTrustedApEncryptionRequired 1.3.6.1.4.1.14179.2.6.2.51
This is the encryption type required by a trusted Rogue.
OBJECT-TYPE    
  INTEGER none(0), open(1), wep(2), wpa(3)  

bsnTrustedApRadioPolicyUsed 1.3.6.1.4.1.14179.2.6.2.52
This is the radio policy used by a trusted Rogue.
OBJECT-TYPE    
  INTEGER none(0), dot11b(1), dot11a(2), dot11bg(3)  

bsnNetworkType 1.3.6.1.4.1.14179.2.6.2.53
OBJECT-TYPE    
  INTEGER dot11b(1), dot11a(2)  

bsnNetworkState 1.3.6.1.4.1.14179.2.6.2.54
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnSignatureType 1.3.6.1.4.1.14179.2.6.2.55
Type of Signature whose attack is detected by the switch.
OBJECT-TYPE    
  INTEGER standard(0), custom(1)  

bsnSignatureName 1.3.6.1.4.1.14179.2.6.2.56
Name of the Signature whose attack is detected by the switch.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

bsnSignatureDescription 1.3.6.1.4.1.14179.2.6.2.57
Description of the Signature whose attack is detected by the switch.
OBJECT-TYPE    
  DisplayString SIZE(0..100)  

bsnImpersonatedAPMacAddr 1.3.6.1.4.1.14179.2.6.2.58
MAC Address of the AP impersonated by another AP.
OBJECT-TYPE    
  MacAddress  

bsnTrustedApPreambleUsed 1.3.6.1.4.1.14179.2.6.2.59
The Preamble on this detecting AP.
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnTrustedApPreambleRequired 1.3.6.1.4.1.14179.2.6.2.60
The Preamble on this detecting AP.
OBJECT-TYPE    
  INTEGER none(0), short(1), long(2)  

bsnSignatureAttackPreced 1.3.6.1.4.1.14179.2.6.2.61
The preced in the standard/custom signature list.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackFrequency 1.3.6.1.4.1.14179.2.6.2.62
The preced in the standard/custom signature list.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackChannel 1.3.6.1.4.1.14179.2.6.2.63
The preced in the standard/custom signature list.
OBJECT-TYPE    
  INTEGER 0..65535  

bsnSignatureAttackerMacAddress 1.3.6.1.4.1.14179.2.6.2.64
The MAC address of the Attacker's mac-interface.
OBJECT-TYPE    
  MacAddress  

bsnLicenseKeyTrapVariable 1.3.6.1.4.1.14179.2.6.2.65
This is the license key that has been found to be deleted, expired or is mismatched causing AP functionality to be disabled on the switch.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

bsnApFunctionalityDisableReasonCode 1.3.6.1.4.1.14179.2.6.2.66
This is the reason why the AP functionality was disabled on the switch. It could be either expiry or deletion or mismatch found of the license key.
OBJECT-TYPE    
  INTEGER unknown(0), licenseKeyExpired(1), licenseKeyDeleted(2), licenseKeyFeatureMismatch(3)  

bsnLicenseKeyFeatureSetTrapVariable 1.3.6.1.4.1.14179.2.6.2.67
This is the switch feature set whose license key has expired or is deleted or is mismatched. To enable the AP functionality again, the license key for this feature set should be re-configured.
OBJECT-TYPE    
  INTEGER wps(1), all(2)  

bsnApRegulatoryDomain 1.3.6.1.4.1.14179.2.6.2.68
The regulatory domain configured on an AP.
OBJECT-TYPE    
  INTEGER a(0), e(1), i(6), j(9), c(16), n(21), k(32), p(33), s(34), t(35), r(48), notavailable(65535)  

bsnAPAuthorizationFailureCause 1.3.6.1.4.1.14179.2.6.2.69
This denotes the reason for AP authorization failure. [entrydoesnotexist]: The AP has not been added to Controller's AP Authorization List. [keymismatch]: The key entry in Controller's AP Authorization list does not match the SHA1 key received from the AP. [invalidCert]: Could not verify the self signed Certificate. [entryIsMIC]: AP has Self Signed Certificate where as in Controller AP Authorization list has Manufactured Installed Certificate [unknown]: Default.
OBJECT-TYPE    
  INTEGER unknown(0), keymismatch(1), entrydoesnotexist(2), invalidCertifcate(3), entryIsMIC(4)  

bsnAPIfUpDownCause 1.3.6.1.4.1.14179.2.6.2.70
This denotes the reason for AP If up or down normal - radio Failure - radio failed radioLowPower - AP is not able draw enough power. maxRetransmission - max retransmission of AP Reached. echoTimeout - heartbeat timeout. configAP - admin enable/disable AP configRadio - admin enable/disable config radio configNetwork - admin enable/disable network
OBJECT-TYPE    
  INTEGER unknown(0), radioFailure(1), radioLowPower(2), maxRetransmission(3), echoTimeout(4), configAP(5), configRadio(6), configNetwork(7)  

bsnAPInvalidRadioType 1.3.6.1.4.1.14179.2.6.2.71
Radio types which are not supported by controller.
OBJECT-TYPE    
  INTEGER unsupportedRadio(0)  

locationNotifyContent 1.3.6.1.4.1.14179.2.6.2.72
This is the content of the notification.
OBJECT-TYPE    
  OCTET STRING SIZE(0..512)  

bsnSignatureMacInfo 1.3.6.1.4.1.14179.2.6.2.73
This object defines the pattern followed by the LWAPP APs to perform signature analysis with this signature and report the results to the Controller.
OBJECT-TYPE    
  BsnTxtSignatureMacInfo  

bsnTraps 1.3.6.1.4.1.14179.2.6.3
OBJECT IDENTIFIER    

bsnDot11StationDisassociate 1.3.6.1.4.1.14179.2.6.3.1
The disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationReasonCode  
  bsnStationMacAddress  

bsnDot11StationDeauthenticate 1.3.6.1.4.1.14179.2.6.3.2
The deauthenticate notification shall be sent when the Station sends a Deauthentication frame. The value of the notification shall include the MAC address of the MAC to which the Deauthentication frame was sent and the reason for the deauthentication.
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationReasonCode  
  bsnStationMacAddress  

bsnDot11StationAuthenticateFail 1.3.6.1.4.1.14179.2.6.3.3
The authenticate failure notification shall be sent when the Station sends an Authentication frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationReasonCode  
  bsnStationMacAddress  

bsnDot11StationAssociateFail 1.3.6.1.4.1.14179.2.6.3.4
The associate failure notification shall be sent when the Station sends an Association frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationReasonCode  
  bsnStationMacAddress  

bsnAPUp 1.3.6.1.4.1.14179.2.6.3.5
When Airespace AP operation status goes up this trap will be sent
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  

bsnAPDown 1.3.6.1.4.1.14179.2.6.3.6
When Airespace AP operation status goes down this trap will be sent
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  

bsnAPAssociated 1.3.6.1.4.1.14179.2.6.3.7
When Airespace AP Associates to a Airespace Switch, AP associated notification will be sent with dot3 MAC address of Airespace AP.This will help management system to discover Airespace AP and add to system.
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnAPPortNumberTrapVariable  

bsnAPDisassociated 1.3.6.1.4.1.14179.2.6.3.8
When Airespace AP disassociates from Airespace Switch, AP disassociated notification will be sent with dot3 MAC address of Airespace AP management system to remove Airespace AP from this Airespace Switch
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  

bsnAPIfUp 1.3.6.1.4.1.14179.2.6.3.9
When Airespace AP's interface's operation status goes up this trap will be sent
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPPortNumber  
  bsnAPIfUpDownCause  

bsnAPIfDown 1.3.6.1.4.1.14179.2.6.3.10
When Airespace AP's interface's operation status goes down this trap will be sent.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPAdminStatus  
  bsnAPIfAdminStatus  
  bsnAPIfUpDownCause  

bsnAPLoadProfileFailed 1.3.6.1.4.1.14179.2.6.3.11
When LOAD Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPNoiseProfileFailed 1.3.6.1.4.1.14179.2.6.3.12
When Noise Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPInterferenceProfileFailed 1.3.6.1.4.1.14179.2.6.3.13
When Interference Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPCoverageProfileFailed 1.3.6.1.4.1.14179.2.6.3.14
When Coverage Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnAPNameTrapVariable  
  bsnAPSlotIdTrapVariable  
  bsnAPCoverageThresholdTrapVariable  
  bsnAPCoverageFailedClients  
  bsnAPCoverageTotalClients  
  bsnClientMacAddr  
  bsnClientRssi  
  bsnClientSnr  

bsnAPCurrentTxPowerChanged 1.3.6.1.4.1.14179.2.6.3.15
Whenever dynamic algorithms are running and bsnAPIfPhyPowerAutomaticOn is true, Airespace AP Interface's CurrentTxPower might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentTxPower for this Airespace AP IF
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfPhyTxPowerLevel  

bsnAPCurrentChannelChanged 1.3.6.1.4.1.14179.2.6.3.16
Whenever dynamic algorithms are running and bsnAPIfPhyChannelAutomaticOn is true, Airespace AP Interface's CurrentChannel might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentChannel for this Airespace AP IF
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnAPSlotIdTrapVariable  
  bsnAPChannelNumberTrapVariable  
  bsnInterferenceEnergyBeforeChannelUpdate  
  bsnInterferenceEnergyAfterChannelUpdate  

bsnRrmDot11aGroupingDone 1.3.6.1.4.1.14179.2.6.3.21
When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
NOTIFICATION-TYPE    
  bsnRrmDot11aGroupLeaderMacAddr  

bsnRrmDot11bGroupingDone 1.3.6.1.4.1.14179.2.6.3.22
When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
NOTIFICATION-TYPE    
  bsnRrmDot11bGroupLeaderMacAddr  

bsnConfigSaved 1.3.6.1.4.1.14179.2.6.3.23
When configuration is save either from CLI or web interface This trap will be sent to inform NMS to do refresh
NOTIFICATION-TYPE    

bsnDot11EssCreated 1.3.6.1.4.1.14179.2.6.3.24
Whenever a new Ess (WLAN) is created, this notification will be sent along with EssIndex
NOTIFICATION-TYPE    
  bsnDot11EssIndex  

bsnDot11EssDeleted 1.3.6.1.4.1.14179.2.6.3.25
Whenever a Ess (WLAN)is deleted, this notification will be sent along with EssIndex
NOTIFICATION-TYPE    
  bsnDot11EssIndex  

bsnRADIUSServerNotResponding 1.3.6.1.4.1.14179.2.6.3.26
This trap is to indicate that no RADIUS server(s) are responding to authentication requests sent by the RADIUS client within the MWAR device(Switch).
NOTIFICATION-TYPE    

bsnAuthenticationFailure 1.3.6.1.4.1.14179.2.6.3.27
This trap is to inform that client authentication failure has occured at MWAR(Switch). This could be cli/web user, wlan user, or Mac Authorized user. ServiceType will indicate which type of user it is and userName will be cli/web/wlan userName or MacAddress of Mac Authorized User
NOTIFICATION-TYPE    
  bsnAuthFailureUserType  
  bsnAuthFailureUserName  

bsnIpsecEspAuthFailureTrap 1.3.6.1.4.1.14179.2.6.3.28
IPsec packets with invalid hashes were found in an inbound ESP SA. The total number of authentication errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnIpsecErrorCount  

bsnIpsecEspReplayFailureTrap 1.3.6.1.4.1.14179.2.6.3.29
IPsec packets with invalid sequence numbers were found in an inbound ESP SA. The total number of replay errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnIpsecErrorCount  

bsnIpsecEspInvalidSpiTrap 1.3.6.1.4.1.14179.2.6.3.31
A packet with an unknown SPI was detected from the specified peer with the specified SPI using the specified protocol. The destination address of the received packet is specified by ipsecLocalAddress. The value ifIndex may be 0 if this optional linkage is unsupported. If the object ipsecSecurityProtocol has the value for IPcomp, then the ipsecSPI object is the CPI of the packet. Implementations SHOULD send one trap per peer (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnIpsecSPI  

bsnIpsecIkeNegFailure 1.3.6.1.4.1.14179.2.6.3.33
An attempt to negotiate a phase 1 IKE SA failed. The notification counts are also sent as part of the trap, along with the current value of the total negotiation error counters for ISAKMP.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnRemoteUdpPort  
  bsnIkeAuthMethod  
  bsnIkeTotalInitFailures  
  bsnIkeTotalInitNoResponses  
  bsnIkeTotalRespFailures  
  bsnNotifiesSent  
  bsnNotifiesReceived  

bsnIpsecSuiteNegFailure 1.3.6.1.4.1.14179.2.6.3.34
An attempt to negotiate a phase 2 SA suite for the specified selector failed. The current total failure counts are passed as well as the notification type counts for the notify involved in the failure.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnSuiteInitFailures  
  bsnSuiteRespondFailures  
  bsnNotifiesSent  
  bsnNotifiesReceived  

bsnIpsecInvalidCookieTrap 1.3.6.1.4.1.14179.2.6.3.35
ISAKMP packets with invalid cookies were detected from the specified source, intended for the specified destination. The initiator and responder cookies are also sent with the trap. The current count is sent to allow the trap to accurately relfect dropped and throttled traps. Implementations SHOULD send one trap per peer (within a reasonable time period, rather than sending one trap per packet.
NOTIFICATION-TYPE    
  bsnRemoteIPv4Address  
  bsnRemoteUdpPort  
  bsnInitiatorCookie  
  bsnResponderCookie  
  bsnIsakmpInvalidCookies  

bsnRogueAPDetected 1.3.6.1.4.1.14179.2.6.3.36
When a Rogue AP is detected this Trap will be sent out along with APMacAddress on which its detected
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnRogueAPAirespaceAPMacAddress  
  bsnRogueAPAirespaceAPSlotId  
  bsnRogueAPSsid  
  bsnRogueAPChannelNumber  
  bsnRogueAPAirespaceAPRSSI  
  bsnRogueAPAirespaceAPSNR  
  bsnRogueAPOnWiredNetwork  
  bsnRogueAdhocMode  
  bsnRogueAPRadioType  
  bsnRogueAPAirespaceAPName  

bsnAPLoadProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.37
When LOAD Profile state changes from FAIL to PASSt this notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPNoiseProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.38
When Noise Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPInterferenceProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.39
When Interference Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable /disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnAPCoverageProfileUpdatedToPass 1.3.6.1.4.1.14179.2.6.3.40
When Coverage Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

bsnRogueAPRemoved 1.3.6.1.4.1.14179.2.6.3.41
When a Rogue AP that was detected earlier no longer exists this Trap will be sent out along with APMacAddress on which its detected
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnRogueAPAirespaceAPMacAddress  
  bsnRogueAPAirespaceAPSlotId  
  bsnRogueAPRadioType  
  bsnRogueAPAirespaceAPName  

bsnRadiosExceedLicenseCount 1.3.6.1.4.1.14179.2.6.3.42
Whenever the currently associated Radios exceed the License Count This trap will be sent to annoy the Customer
NOTIFICATION-TYPE    
  bsnCurrentRadiosCount  
  bsnLicenseRadioCount  

bsnSensedTemperatureTooHigh 1.3.6.1.4.1.14179.2.6.3.43
Temperature sensor temp too High - temp is too high on the unit. Immediate action should be taken
NOTIFICATION-TYPE    
  bsnSensorTemperature  

bsnSensedTemperatureTooLow 1.3.6.1.4.1.14179.2.6.3.44
Temperature sensor temp too Low - temp is too high on the unit. Immediate action should be taken
NOTIFICATION-TYPE    
  bsnSensorTemperature  

bsnTemperatureSensorFailure 1.3.6.1.4.1.14179.2.6.3.45
Temperature sensor hw failure - temp sensor has failed. Temperature is unknown
NOTIFICATION-TYPE    

bsnTemperatureSensorClear 1.3.6.1.4.1.14179.2.6.3.46
Temperature sensor clear -- temp sensor alarm condition is over. sensor is operating within proper temp range
NOTIFICATION-TYPE    
  bsnSensorTemperature  

bsnPOEControllerFailure 1.3.6.1.4.1.14179.2.6.3.47
POE Controller has failed. Its a very critical trap. User intervention is required.
NOTIFICATION-TYPE    

bsnMaxRogueCountExceeded 1.3.6.1.4.1.14179.2.6.3.48
The number of rogues has exceeded the maximum Rogues allowed
NOTIFICATION-TYPE    
  bsnMaxRogueCount  

bsnMaxRogueCountClear 1.3.6.1.4.1.14179.2.6.3.49
The number of rogues is within the maximum Rogues allowed
NOTIFICATION-TYPE    
  bsnMaxRogueCount  

bsnApMaxRogueCountExceeded 1.3.6.1.4.1.14179.2.6.3.50
The number of rogues has exceeded the maximum Rogues allowed on the AP
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnMaxRogueCount  

bsnApMaxRogueCountClear 1.3.6.1.4.1.14179.2.6.3.51
The number of rogues is within the maximum Rogues allowed on the AP
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnMaxRogueCount  

bsnDot11StationBlacklisted 1.3.6.1.4.1.14179.2.6.3.52
The station blacklisted notification shall be sent when the client is blacklisted. The reason could be repeated auth or association failures or IP Address theft. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent, the MAC and Slot Id of AP that client was associated to and the reason for black listing.
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationBlacklistingReasonCode  
  bsnStationMacAddress  

bsnDot11StationAssociate 1.3.6.1.4.1.14179.2.6.3.53
The associate notification shall be sent when any of the watchlisted clients(present on at least one watch list) associates with an AP. The value of the notification shall include the MAC address and the Slot ID of the radio to which the station Associated.
NOTIFICATION-TYPE    
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnStationMacAddress  
  bsnStationUserName  

bsnApBigNavDosAttack 1.3.6.1.4.1.14179.2.6.3.55
The AP sent a string of messages with large NAV field and all 802.11 traffic on that channel was suspended.
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  
  bsnAPSlotIdTrapVariable  
  bsnNavDosAttackSourceMacAddr  

bsnTooManyUnsuccessLoginAttempts 1.3.6.1.4.1.14179.2.6.3.56
The Management User made too many unsuccessful login attempts.
NOTIFICATION-TYPE    
  bsnUserIpAddress  
  bsnStationUserName  

bsnWepKeyDecryptError 1.3.6.1.4.1.14179.2.6.3.57
Issued when a decrypt error occurrs. The WEP Key configured at the station may be wrong.
NOTIFICATION-TYPE    
  bsnStationMacAddress  
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  

bsnWpaMicErrorCounterActivated 1.3.6.1.4.1.14179.2.6.3.58
Issued when a WPA MIC error occurs and a counter measure is activated at the AP.
NOTIFICATION-TYPE    
  bsnStationMacAddress  
  bsnStationAPMacAddr  
  bsnStationAPIfSlotId  
  bsnWlanIdTrapVariable  

bsnRogueAPDetectedOnWiredNetwork 1.3.6.1.4.1.14179.2.6.3.59
When a Rogue is detected on the wired network this trap will be sent out. The same trap with bsnRogueAPOnWiredNetwork set to no will clear the previous trap.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnRogueAPOnWiredNetwork  

bsnApHasNoRadioCards 1.3.6.1.4.1.14179.2.6.3.60
When an AP has no radio cards present on it, the switch sends this trap.
NOTIFICATION-TYPE    
  bsnAPMacAddrTrapVariable  

bsnDuplicateIpAddressReported 1.3.6.1.4.1.14179.2.6.3.61
This trap is issued when the switch or an AP detects another machine using its IP Address. The first variable has value yes if the duplicate IP is reported by an AP. In that case, the second attribute will carry the AP MAC Address. The third variable is the duplicate IP address in question and the last attribute is the MAC Address of the machine that is found to be using the duplicate IP.
NOTIFICATION-TYPE    
  bsnDuplicateIpReportedByAP  
  bsnAPMacAddrTrapVariable  
  bsnDuplicateIpTrapVariable  
  bsnRogueAPDot11MacAddress  
  bsnDuplicateIpTrapClear  

bsnAPContainedAsARogue 1.3.6.1.4.1.14179.2.6.3.62
When our AP detects that it is being contained by another AP, this trap is issued. The clear flag is true if the AP is no longer being contained.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  
  bsnClearTrapVariable  

bsnTrustedApHasInvalidSsid 1.3.6.1.4.1.14179.2.6.3.63
Issued when a Trusted Rogue AP is auto contained for advertising invalid SSID. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnClearTrapVariable  

bsnTrustedApIsMissing 1.3.6.1.4.1.14179.2.6.3.64
Issued when a Trusted Rogue AP is missing or has failed. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnClearTrapVariable  

bsnAdhocRogueAutoContained 1.3.6.1.4.1.14179.2.6.3.65
Issued when an Adhoc Rogue is auto contained. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnClearTrapVariable  

bsnRogueApAutoContained 1.3.6.1.4.1.14179.2.6.3.66
Issued when a Rogue AP is auto contained for advertising our SSID. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnClearTrapVariable  

bsnTrustedApHasInvalidEncryption 1.3.6.1.4.1.14179.2.6.3.67
Issued when a Trusted Rogue AP is auto contained for using invalid encryption. The second param is for the encryption used and the third param is for encryption required. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnTrustedApEncryptionUsed  
  bsnTrustedApEncryptionRequired  
  bsnClearTrapVariable  

bsnTrustedApHasInvalidRadioPolicy 1.3.6.1.4.1.14179.2.6.3.68
Issued when a Trusted Rogue AP is auto contained for using invalid radio policy. The second param is for the radio policy used and the third param is for radio policy required. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnTrustedApRadioPolicyUsed  
  bsnTrustedApRadioPolicyRequired  
  bsnClearTrapVariable  

bsnNetworkStateChanged 1.3.6.1.4.1.14179.2.6.3.69
When the 802.11a or b/g network state is changed this trap is issued.
NOTIFICATION-TYPE    
  bsnNetworkType  
  bsnNetworkState  

bsnSignatureAttackDetected 1.3.6.1.4.1.14179.2.6.3.70
This trap is sent out when a signature attack is detected by the switch. The standard and custom signatures are predefined on the switch (see bsnSignatureConfig group). The signatures also defines if its detection should be reported. The trap variables bsnSignatureName and bsnSignatureDescription are retrieved from the detected signature definition. Clear Trap Variable is turned on when the signature attack stops. The signature's quiet time configuration speicifes the time after which the clear trap would be sent. bsnSignatureMacInfo indicates whether the signature is used to track pattern matches for all source MAC addresses together or seperately for individual source MAC addresses. bsnSignatureAttackFrequency will carry the value for a specific MAC address or for all MAC addresses depending on bsnSignatureMacInfo.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPName  
  bsnAPIfType  
  bsnSignatureType  
  bsnSignatureName  
  bsnSignatureDescription  
  bsnClearTrapVariable  
  bsnSignatureAttackPreced  
  bsnSignatureAttackFrequency  
  bsnSignatureAttackChannel  
  bsnSignatureAttackerMacAddress  
  bsnSignatureMacInfo  

bsnAPRadioCardTxFailure 1.3.6.1.4.1.14179.2.6.3.71
This trap is sent by the switch when a radio card on an AP stops transmitting.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  

bsnAPRadioCardTxFailureClear 1.3.6.1.4.1.14179.2.6.3.72
This trap is sent by the switch when a radio card on an AP starts transmitting again after a prior failure.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  

bsnAPRadioCardRxFailure 1.3.6.1.4.1.14179.2.6.3.73
This trap is sent by the switch when a radio card on an AP stops receiving.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  

bsnAPRadioCardRxFailureClear 1.3.6.1.4.1.14179.2.6.3.74
This trap is sent by the switch when a radio card on an AP starts receiving again after a prior failure.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  

bsnAPImpersonationDetected 1.3.6.1.4.1.14179.2.6.3.75
This trap is sent by the switch when a radio of an authenticated AP hears from another AP whose MAC Address neither matches that of a rogue's and nor is it an authenticated neighbor of the detecting AP.
NOTIFICATION-TYPE    
  bsnImpersonatedAPMacAddr  
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfType  

bsnTrustedApHasInvalidPreamble 1.3.6.1.4.1.14179.2.6.3.76
Issued when a Trusted Rogue AP is auto contained for using invalid preamble. The second param is for the preamble used and the third param is for preamble required. If the clear variable has value true, then the trap clears the earlier alert.
NOTIFICATION-TYPE    
  bsnRogueAPDot11MacAddress  
  bsnTrustedApPreambleUsed  
  bsnTrustedApPreambleRequired  
  bsnClearTrapVariable  

bsnAPIPAddressFallback 1.3.6.1.4.1.14179.2.6.3.77
This trap is sent out when an AP, with the configured static ip-address, fails to establish connection with outside world and starts using DHCP as a fallback option.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnApIpAddress  
  bsnAPStaticIPAddress  

bsnAPFunctionalityDisabled 1.3.6.1.4.1.14179.2.6.3.78
This trap is sent out when AP functionality on the switch is disabled because the License key has expired or has been deleted or doesn't match the switch image.
NOTIFICATION-TYPE    
  bsnApFunctionalityDisableReasonCode  
  bsnLicenseKeyTrapVariable  
  bsnLicenseKeyFeatureSetTrapVariable  

bsnAPRegulatoryDomainMismatch 1.3.6.1.4.1.14179.2.6.3.79
This trap is generated if an AP's regulatory domain doesn't match the country the switch is configured for. Due to the mismatch, the AP will fail to associate with the Switch.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPName  
  bsnApRegulatoryDomain  
  bsnGlobalDot11CountryIndex  

bsnRxMulticastQueueFull 1.3.6.1.4.1.14179.2.6.3.80
This trap indicates that the CPU's Receive Multicast Queue is Full.
NOTIFICATION-TYPE    

bsnRadarChannelDetected 1.3.6.1.4.1.14179.2.6.3.81
This trap is sent when radar signals are detected on the current channel
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfPhyChannelNumber  

bsnRadarChannelCleared 1.3.6.1.4.1.14179.2.6.3.82
This trap will be generated, if a radar trap has been generated earlier, after the expiry of Non-Occupancy Period.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPIfPhyChannelNumber  

bsnAPAuthorizationFailure 1.3.6.1.4.1.14179.2.6.3.83
This trap is sent out in case of authorization failure while attempting to associate the AP to the controller. bsnAPDot3MacAddress represents the mac-address of that AP. bsnAPName is name of AP
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPName  
  bsnAPAuthCertificateType  
  bsnAPAuthorizationFailureCause  

radioCoreDumpTrap 1.3.6.1.4.1.14179.2.6.3.84
When radio module in AP dumps core, it informs controller and controller generates this trap. The core file can be retrieved on demand.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  

invalidRadioTrap 1.3.6.1.4.1.14179.2.6.3.85
This trap will be generated when an AP has joined is using unsupported radio or a radio slot not currently not being used.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPIfSlotId  
  bsnAPInvalidRadioType  

countryChangeTrap 1.3.6.1.4.1.14179.2.6.3.86
This trap will be generated when an operator changes the country of operation. New country code will be sent in trap.
NOTIFICATION-TYPE    
  bsnGlobalDot11CountryIndex  

unsupportedAPTrap 1.3.6.1.4.1.14179.2.6.3.87
This trap will be generated when unsupported AP try to join 40xx/410x or 3500 with 64MB flash.
NOTIFICATION-TYPE    
  bsnAPDot3MacAddress  
  bsnAPName  

heartbeatLossTrap 1.3.6.1.4.1.14179.2.6.3.88
This trap will be generated when controller loses connection with the Supervisor Switch in which it is physically embedded and doesn't hear the heartbeat keepalives from the Supervisor.
NOTIFICATION-TYPE    

locationNotifyTrap 1.3.6.1.4.1.14179.2.6.3.89
This trap will be generated by the location server for notifications of location events.
NOTIFICATION-TYPE    
  locationNotifyContent  

bsnUtility 1.3.6.1.4.1.14179.2.7
OBJECT IDENTIFIER    

bsnSyslog 1.3.6.1.4.1.14179.2.7.1
OBJECT IDENTIFIER    

bsnSyslogEnable 1.3.6.1.4.1.14179.2.7.1.1
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

bsnSyslogRemoteAddress 1.3.6.1.4.1.14179.2.7.1.2
This would be the IP Address or host name
OBJECT-TYPE    
  DisplayString  

bsnPing 1.3.6.1.4.1.14179.2.7.2
OBJECT IDENTIFIER    

bsnPingTestTable 1.3.6.1.4.1.14179.2.7.2.1
PingTest Table
OBJECT-TYPE    
  SEQUENCE OF  
    BsnPingTestEntry

bsnPingTestEntry 1.3.6.1.4.1.14179.2.7.2.1.1
An Entry (conceptual row) in the bsnPingTest Table.
OBJECT-TYPE    
  BsnPingTestEntry  

bsnPingTestId 1.3.6.1.4.1.14179.2.7.2.1.1.1
Test ID
OBJECT-TYPE    
  Integer32 0..24  

bsnPingTestIPAddress 1.3.6.1.4.1.14179.2.7.2.1.1.2
Ip Address to ping
OBJECT-TYPE    
  IpAddress  

bsnPingTestSendCount 1.3.6.1.4.1.14179.2.7.2.1.1.3
Number of bytes sent
OBJECT-TYPE    
  Integer32 1..20  

bsnPingTestReceivedCount 1.3.6.1.4.1.14179.2.7.2.1.1.4
Number of bytes received.
OBJECT-TYPE    
  Integer32 1..20  

bsnPingTestStatus 1.3.6.1.4.1.14179.2.7.2.1.1.5
Status of the ping test
OBJECT-TYPE    
  INTEGER inprogress(1), complete(2)  

bsnPingTestRowStatus 1.3.6.1.4.1.14179.2.7.2.1.1.25
Row Status
OBJECT-TYPE    
  RowStatus  

bsnLinkTest 1.3.6.1.4.1.14179.2.7.3
OBJECT IDENTIFIER    

bsnLinkTestTable 1.3.6.1.4.1.14179.2.7.3.1
LinkTest Table
OBJECT-TYPE    
  SEQUENCE OF  
    BsnLinkTestEntry

bsnLinkTestEntry 1.3.6.1.4.1.14179.2.7.3.1.1
An Entry (conceptual row) in the bsnLinkTest Table.
OBJECT-TYPE    
  BsnLinkTestEntry  

bsnLinkTestId 1.3.6.1.4.1.14179.2.7.3.1.1.1
Link Test ID
OBJECT-TYPE    
  Integer32 0..24  

bsnLinkTestMacAddress 1.3.6.1.4.1.14179.2.7.3.1.1.2
MAC Address of link to test
OBJECT-TYPE    
  MacAddress  

bsnLinkTestSendPktCount 1.3.6.1.4.1.14179.2.7.3.1.1.3
Number of packets sent.
OBJECT-TYPE    
  Integer32 1..20  

bsnLinkTestSendPktLength 1.3.6.1.4.1.14179.2.7.3.1.1.4
Length of sent packet
OBJECT-TYPE    
  Integer32 1..2000  

bsnLinkTestReceivedPktCount 1.3.6.1.4.1.14179.2.7.3.1.1.5
Number of received packets.
OBJECT-TYPE    
  Integer32  

bsnLinkTestClientRSSI 1.3.6.1.4.1.14179.2.7.3.1.1.6
Client RSSI value of link.
OBJECT-TYPE    
  Integer32  

bsnLinkTestLocalSNR 1.3.6.1.4.1.14179.2.7.3.1.1.7
Local SNR of the link
OBJECT-TYPE    
  Integer32  

bsnLinkTestLocalRSSI 1.3.6.1.4.1.14179.2.7.3.1.1.8
Local RSSI of the link.
OBJECT-TYPE    
  Integer32  

bsnLinkTestStatus 1.3.6.1.4.1.14179.2.7.3.1.1.9
Status of the link test.
OBJECT-TYPE    
  INTEGER inprogress(1), complete(2)  

bsnLinkTestRowStatus 1.3.6.1.4.1.14179.2.7.3.1.1.30
Row Status
OBJECT-TYPE    
  RowStatus  

bsnMobility 1.3.6.1.4.1.14179.2.8
OBJECT IDENTIFIER    

bsnMobilityConfig 1.3.6.1.4.1.14179.2.8.1
OBJECT IDENTIFIER    

bsnMobilityProtocolPortNum 1.3.6.1.4.1.14179.2.8.1.1
Port Number on which mobility Protocol runs
OBJECT-TYPE    
  Integer32  

bsnMobilityDynamicDiscovery 1.3.6.1.4.1.14179.2.8.1.3
Statically Configured is always enabled if members are defined. To further enable rrm discovery, learned discovery, broadcast discovery, enable/disable this attribute.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnMobilityStatsReset 1.3.6.1.4.1.14179.2.8.1.4
Reset mobility statistics by setting this atribute to resetNow. If you try to read this attribute value will always be 0.
OBJECT-TYPE    
  INTEGER default(0), resetNow(1)  

bsnMobilityGroupMembersTable 1.3.6.1.4.1.14179.2.8.1.10
MWAR List (statically configured members of the mobility group)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityGroupMembersEntry

bsnMobilityGroupMembersEntry 1.3.6.1.4.1.14179.2.8.1.10.1
An Entry (conceptual row) in the bsnMobilityGroupMembers Table.
OBJECT-TYPE    
  BsnMobilityGroupMembersEntry  

bsnMobilityGroupMemberMacAddress 1.3.6.1.4.1.14179.2.8.1.10.1.1
Member switch MAC Address
OBJECT-TYPE    
  MacAddress  

bsnMobilityGroupMemberIPAddress 1.3.6.1.4.1.14179.2.8.1.10.1.2
Member switch IP Address
OBJECT-TYPE    
  IpAddress  

bsnMobilityGroupMemberGroupName 1.3.6.1.4.1.14179.2.8.1.10.1.3
Member's group name. If left empty while adding a new group member, this assumes the default mobility group name of the switch.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

bsnMobilityGroupMemberRowStatus 1.3.6.1.4.1.14179.2.8.1.10.1.22
Row Status
OBJECT-TYPE    
  RowStatus  

bsnMobilityAnchorsTable 1.3.6.1.4.1.14179.2.8.1.11
Statically configured mobility anchors
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityAnchorsEntry

bsnMobilityAnchorsEntry 1.3.6.1.4.1.14179.2.8.1.11.1
An Entry (conceptual row) in the bsnMobilityAnchorsTable Table.
OBJECT-TYPE    
  BsnMobilityAnchorsEntry  

bsnMobilityAnchorWlanSsid 1.3.6.1.4.1.14179.2.8.1.11.1.1
Local wlan-ssid to connect to Guest/Anchor switch
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnMobilityAnchorSwitchIPAddress 1.3.6.1.4.1.14179.2.8.1.11.1.2
Guest/Anchor switch IP Address
OBJECT-TYPE    
  IpAddress  

bsnMobilityAnchorRowStatus 1.3.6.1.4.1.14179.2.8.1.11.1.20
Row Status
OBJECT-TYPE    
  RowStatus  

bsnMobilityStats 1.3.6.1.4.1.14179.2.8.2
OBJECT IDENTIFIER    

bsnTotalHandoffRequests 1.3.6.1.4.1.14179.2.8.2.1
Total handoff requests
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffs 1.3.6.1.4.1.14179.2.8.2.2
Total handoffs
OBJECT-TYPE    
  Counter32  

bsnCurrentExportedClients 1.3.6.1.4.1.14179.2.8.2.3
Current exported client count
OBJECT-TYPE    
  Counter32  

bsnTotalExportedClients 1.3.6.1.4.1.14179.2.8.2.4
Total exported client count
OBJECT-TYPE    
  Counter32  

bsnCurrentImportedClients 1.3.6.1.4.1.14179.2.8.2.5
Current Imported client count
OBJECT-TYPE    
  Counter32  

bsnTotalImportedClients 1.3.6.1.4.1.14179.2.8.2.6
Total Imported client count
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffErrors 1.3.6.1.4.1.14179.2.8.2.7
Total handoff errors
OBJECT-TYPE    
  Counter32  

bsnTotalCommunicationErrors 1.3.6.1.4.1.14179.2.8.2.8
Total communication errors
OBJECT-TYPE    
  Counter32  

bsnMobilityGroupDirectoryTable 1.3.6.1.4.1.14179.2.8.2.9
MWAR List (statically configured members of the mobility group)
OBJECT-TYPE    
  SEQUENCE OF  
    BsnMobilityGroupDirectoryEntry

bsnMobilityGroupDirectoryEntry 1.3.6.1.4.1.14179.2.8.2.9.1
An Entry (conceptual row) in the bsnMobilityGroupDirectory Table.
OBJECT-TYPE    
  BsnMobilityGroupDirectoryEntry  

bsnGroupDirectoryMemberIPAddress 1.3.6.1.4.1.14179.2.8.2.9.1.1
Mwar Ip Address
OBJECT-TYPE    
  IpAddress  

bsnGroupDirectoryMemberMacAddress 1.3.6.1.4.1.14179.2.8.2.9.1.2
Mwar Mac Address
OBJECT-TYPE    
  MacAddress  

bsnGroupDirectoryDicoveryType 1.3.6.1.4.1.14179.2.8.2.9.1.3
Discovery type of the Group Directory.
OBJECT-TYPE    
  INTEGER static(1), rrm(2), broadcast(3), learned(4)  

bsnMemberCurrentAnchoredClients 1.3.6.1.4.1.14179.2.8.2.9.1.4
Current anchored client count
OBJECT-TYPE    
  Counter32  

bsnMemberTotalAnchoredClients 1.3.6.1.4.1.14179.2.8.2.9.1.5
Total anchored client count
OBJECT-TYPE    
  Counter32  

bsnMemberCurrentExportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.6
Current exported client count
OBJECT-TYPE    
  Counter32  

bsnMemberTotalExportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.7
Total exported client count
OBJECT-TYPE    
  Counter32  

bsnMemberCurrentImportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.8
Current Imported client count
OBJECT-TYPE    
  Counter32  

bsnMemberTotalImportedClients 1.3.6.1.4.1.14179.2.8.2.9.1.9
Total Imported client count
OBJECT-TYPE    
  Counter32  

bsnMemberTotalHandoffErrors 1.3.6.1.4.1.14179.2.8.2.9.1.10
Total handoff errors
OBJECT-TYPE    
  Counter32  

bsnMemberTotalCommunicationErrors 1.3.6.1.4.1.14179.2.8.2.9.1.30
Total Communication errors
OBJECT-TYPE    
  Counter32  

bsnTotalReceiveErrors 1.3.6.1.4.1.14179.2.8.2.10
Total receive errors
OBJECT-TYPE    
  Counter32  

bsnTotalTransmitErrors 1.3.6.1.4.1.14179.2.8.2.11
Total Transmit errors
OBJECT-TYPE    
  Counter32  

bsnTotalResponsesRetransmitted 1.3.6.1.4.1.14179.2.8.2.12
Total Responses Retransmitted
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffEndRequestsReceived 1.3.6.1.4.1.14179.2.8.2.13
Total Handoff End Requests Received
OBJECT-TYPE    
  Counter32  

bsnTotalStateTransitionsDisallowed 1.3.6.1.4.1.14179.2.8.2.14
Total State Transitions Disallowed
OBJECT-TYPE    
  Counter32  

bsnTotalResourceErrors 1.3.6.1.4.1.14179.2.8.2.15
Total Resource Errors
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsSent 1.3.6.1.4.1.14179.2.8.2.16
Total Handoff Requests Sent
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRepliesReceived 1.3.6.1.4.1.14179.2.8.2.17
Total Handoff Replies Received
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffAsLocalReceived 1.3.6.1.4.1.14179.2.8.2.18
Total Handoffs As Local Received
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffAsForeignReceived 1.3.6.1.4.1.14179.2.8.2.19
Total Handoffs As Foreign Received
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffDeniesReceived 1.3.6.1.4.1.14179.2.8.2.20
Total Handoff Denies Received
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsSent 1.3.6.1.4.1.14179.2.8.2.21
Total Anchor Requests Sent
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorDenyReceived 1.3.6.1.4.1.14179.2.8.2.22
Total Anchor Deny Received
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorGrantReceived 1.3.6.1.4.1.14179.2.8.2.23
Total Anchor Grant Received
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorTransferReceived 1.3.6.1.4.1.14179.2.8.2.24
Total Anchor Transfer Received
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsIgnored 1.3.6.1.4.1.14179.2.8.2.25
Total Handoff Requests Ignored
OBJECT-TYPE    
  Counter32  

bsnTotalPingPongHandoffRequestsDropped 1.3.6.1.4.1.14179.2.8.2.26
Total Ping Pong Handoff Requests Dropped
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsDropped 1.3.6.1.4.1.14179.2.8.2.27
Total Handoff Requests Dropped
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsDenied 1.3.6.1.4.1.14179.2.8.2.28
Total Handoff Requests Denied
OBJECT-TYPE    
  Counter32  

bsnTotalClientHandoffAsLocal 1.3.6.1.4.1.14179.2.8.2.29
Total Client Handoffs As Local
OBJECT-TYPE    
  Counter32  

bsnTotalClientHandoffAsForeign 1.3.6.1.4.1.14179.2.8.2.30
Total Client Handoffs As Foreign
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsReceived 1.3.6.1.4.1.14179.2.8.2.31
Total Anchor Requests Received
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsDenied 1.3.6.1.4.1.14179.2.8.2.32
Total Anchor Requests Denied
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorRequestsGranted 1.3.6.1.4.1.14179.2.8.2.33
Total Anchor Requests Granted
OBJECT-TYPE    
  Counter32  

bsnTotalAnchorTransferred 1.3.6.1.4.1.14179.2.8.2.34
Total Anchor Transferred
OBJECT-TYPE    
  Counter32  

bsnTotalHandoffRequestsReceived 1.3.6.1.4.1.14179.2.8.2.35
Total Handoff Requests Received
OBJECT-TYPE    
  Counter32  

bsnIpsec 1.3.6.1.4.1.14179.2.9
OBJECT IDENTIFIER    

bsnWrasIpsecCACertificate 1.3.6.1.4.1.14179.2.9.1
OBJECT-TYPE    
  OCTET STRING SIZE(0..4096)  

bsnWrasIpsecCACertificateUpdate 1.3.6.1.4.1.14179.2.9.2
Note this attribute is for updating the certificate If you try to read it, it will always be ***
OBJECT-TYPE    
  OCTET STRING SIZE(0..4096)  

bsnWrasIpsecCertTable 1.3.6.1.4.1.14179.2.9.3
A table of Certificates.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnWrasIpsecCertEntry

bsnWrasIpsecCertEntry 1.3.6.1.4.1.14179.2.9.3.1
Each entry contains a specific certificate.
OBJECT-TYPE    
  BsnWrasIpsecCertEntry  

bsnWrasIpsecCertName 1.3.6.1.4.1.14179.2.9.3.1.1
The name assigned to this set of IKE Certificates.
OBJECT-TYPE    
  DisplayString SIZE(0..80)  

bsnWrasIpsecCertificateUpdate 1.3.6.1.4.1.14179.2.9.3.1.2
If you try to read this it will always be ***
OBJECT-TYPE    
  OCTET STRING SIZE(0..4096)  

bsnWrasIpsecCertificate 1.3.6.1.4.1.14179.2.9.3.1.3
OBJECT-TYPE    
  OCTET STRING SIZE(0..4096)  

bsnWrasIpsecCertPassword 1.3.6.1.4.1.14179.2.9.3.1.4
OBJECT-TYPE    
  OCTET STRING SIZE(0..1500)  

bsnWrasIpsecCertStatus 1.3.6.1.4.1.14179.2.9.3.1.24
A row status type for the IKE Cert Entry.
OBJECT-TYPE    
  RowStatus  

bsnAPGroupsVlanConfig 1.3.6.1.4.1.14179.2.10
OBJECT IDENTIFIER    

bsnAPGroupsVlanFeature 1.3.6.1.4.1.14179.2.10.1
When enabled, Site Specific WLAN feature is enforced.
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

bsnAPGroupsVlanTable 1.3.6.1.4.1.14179.2.10.2
Wireless Sites Table.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPGroupsVlanEntry

bsnAPGroupsVlanEntry 1.3.6.1.4.1.14179.2.10.2.1
An entry in bsnAPGroupsVlanTable.
OBJECT-TYPE    
  BsnAPGroupsVlanEntry  

bsnAPGroupsVlanName 1.3.6.1.4.1.14179.2.10.2.1.1
The string is an unique identifier/name assigned to a site.
OBJECT-TYPE    
  OCTET STRING SIZE(1..31)  

bsnAPGroupsVlanDescription 1.3.6.1.4.1.14179.2.10.2.1.2
Description about the site.
OBJECT-TYPE    
  OCTET STRING SIZE(0..31)  

bsnAPGroupsVlanRowStatus 1.3.6.1.4.1.14179.2.10.2.1.20
Row Status for creation/deletion of entries in bsnAPGroupsVlanTable
OBJECT-TYPE    
  RowStatus  

bsnAPGroupsVlanMappingTable 1.3.6.1.4.1.14179.2.10.3
A table for the WLAN-interace-mappings allowed for each configured site. Each site can have a set of WLANs associated with it.
OBJECT-TYPE    
  SEQUENCE OF  
    BsnAPGroupsVlanMappingEntry

bsnAPGroupsVlanMappingEntry 1.3.6.1.4.1.14179.2.10.3.1
An entry in bsnAPGroupsVlanMappingTable.
OBJECT-TYPE    
  BsnAPGroupsVlanMappingEntry  

bsnAPGroupsVlanMappingSsid 1.3.6.1.4.1.14179.2.10.3.1.1
When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingSsid' is the wlan to be used when a client connects on this AP.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

bsnAPGroupsVlanMappingInterfaceName 1.3.6.1.4.1.14179.2.10.3.1.2
When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingInterfaceName' is the interface to be used when a client connects to the 'bsnAPGroupsVlanMappingSsid' WLAN on this AP.
OBJECT-TYPE    
  OCTET STRING SIZE(1..32)  

bsnAPGroupsVlanMappingRowStatus 1.3.6.1.4.1.14179.2.10.3.1.20
Row Status for creation/deletion of WLAN-interface-mappings asscoiated with sites.
OBJECT-TYPE    
  RowStatus  

bsnWrasGroups 1.3.6.1.4.1.14179.2.50
OBJECT IDENTIFIER    

bsnEssGroup 1.3.6.1.4.1.14179.2.50.1
This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.
OBJECT-GROUP    

bsnApGroup 1.3.6.1.4.1.14179.2.50.2
This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.
OBJECT-GROUP    

bsnGlobalDot11Group 1.3.6.1.4.1.14179.2.50.3
This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.
OBJECT-GROUP    

bsnRrmGroup 1.3.6.1.4.1.14179.2.50.4
This collection of objects provide the information about Airespace Radio Resource Management Configuration Parameters. These objects are defined under bsnRrm object.
OBJECT-GROUP    

bsnAAAGroup 1.3.6.1.4.1.14179.2.50.5
This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.
OBJECT-GROUP    

bsnTrapsGroup 1.3.6.1.4.1.14179.2.50.6
This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.
OBJECT-GROUP    

bsnUtilityGroup 1.3.6.1.4.1.14179.2.50.7
This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.
OBJECT-GROUP    

bsnMobilityGroup 1.3.6.1.4.1.14179.2.50.8
This collection of objects provide the information about Airespace Mobility Group Parameters and ststistics. These are objects defined under bsnMobility.
OBJECT-GROUP    

bsnIpsecGroup 1.3.6.1.4.1.14179.2.50.9
This collection of objects provide the information about Airespace Global IpSec Group. These objects are defined under bsnIpsec.
OBJECT-GROUP    

bsnWrasDepGroup 1.3.6.1.4.1.14179.2.50.10
This collection of objects are derprecated in bsnWireless module.
OBJECT-GROUP    

bsnWrasObsGroup 1.3.6.1.4.1.14179.2.50.11
This collection of objects are obsoleted in bsnWireless module.
OBJECT-GROUP    

bsnWrasTrap 1.3.6.1.4.1.14179.2.50.12
This collection of objects provides all notification that Switch need to generate to the Management System.
NOTIFICATION-GROUP    

bsnWrasCompliances 1.3.6.1.4.1.14179.2.51
OBJECT IDENTIFIER    

bsnWrasCompliance 1.3.6.1.4.1.14179.2.51.1
The compliance statement for the SNMP entities that implement the bsnWireless module.
MODULE-COMPLIANCE    

Defined Objects

WEPKeytype  
OCTET STRING SIZE(4..32)    

ProfileState  
INTEGER pass(1), fail(0)    

BsnTxtSignatureMacInfo  
This textual convention defines the pattern followed by the LWAPP APs to perform signature analysis with the signature and report the results to the Controller. The semantics are described as follows. bsnSignatureMacAll - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked and reported on a per-signature and per-channel basis. bsnSignatureMacIndividual - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked and reported separately for individual MAC addresses, that are the sources of the received 802.11 data and/or management frames. bsnStandardSigMacBoth - The Controller would set the 'Mac Info' parameter of the 'Signature Add LWAPP Message' to this value to indicate the LWAPP AP that the signature analysis and pattern matching should be tracked on a per signature as well as per-MAC address basis.
TEXTUAL-CONVENTION    
  INTEGER bsnSignatureMacAll(0), bsnSignatureMacIndividual(1), bsnSignatureMacBoth(2)  

BsnSignaturePatternOffSetStart  
This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames. This is introduced since 802.11e QOS frames have an additional 2-byte QOS header which results in the current implementation not being able to find the start of the date frames for signature analysis. The semantics of the values are as follows. sigPattStartFrm - This indicates that the required offset should be applied to the start of the data frame, before performing pattern matching of the signature on the data frame. sigPattStartFrmBody - This value indicates that the required offset should be applied to the start of the frame body, after the header, before performing pattern matching of the signature on the data frame.
TEXTUAL-CONVENTION    
  INTEGER sigPattStartFrm(0), sigPattStartFrmBody(1)  

BsnDot11EssEntry  
SEQUENCE    
  Unsigned32 as bsnDot11EssIndex  
  DisplayString as bsnDot11EssSsid  
  Unsigned32 as bsnDot11EssSessionTimeout  
  INTEGER as bsnDot11EssMacFiltering  
  INTEGER as bsnDot11EssAdminStatus  
  INTEGER as bsnDot11EssSecurityAuthType  
  INTEGER as bsnDot11EssStaticWEPSecurity  
  INTEGER as bsnDot11EssStaticWEPEncryptionType  
  WEPKeytype as bsnDot11EssStaticWEPDefaultKey  
  INTEGER as bsnDot11EssStaticWEPKeyIndex  
  INTEGER as bsnDot11EssStaticWEPKeyFormat  
  INTEGER as bsnDot11Ess8021xSecurity  
  INTEGER as bsnDot11Ess8021xEncryptionType  
  INTEGER as bsnDot11EssWPASecurity  
  INTEGER as bsnDot11EssWPAEncryptionType  
  INTEGER as bsnDot11EssWPAAuthKeyMgmtMode  
  OCTET STRING as bsnDot11EssWPAAuthPresharedKey  
  OCTET STRING as bsnDot11EssWPAAuthPresharedKeyHex  
  INTEGER as bsnDot11EssIpsecSecurity  
  INTEGER as bsnDot11EssVpnEncrTransform  
  INTEGER as bsnDot11EssVpnAuthTransform  
  INTEGER as bsnDot11EssVpnIkeAuthMode  
  OCTET STRING as bsnDot11EssVpnSharedKey  
  Unsigned32 as bsnDot11EssVpnSharedKeySize  
  INTEGER as bsnDot11EssVpnIkePhase1Mode  
  Integer32 as bsnDot11EssVpnIkeLifetime  
  INTEGER as bsnDot11EssVpnIkeDHGroup  
  INTEGER as bsnDot11EssIpsecPassthruSecurity  
  IpAddress as bsnDot11EssVpnPassthruGateway  
  INTEGER as bsnDot11EssWebSecurity  
  INTEGER as bsnDot11EssRadioPolicy  
  INTEGER as bsnDot11EssQualityOfService  
  INTEGER as bsnDot11EssDhcpRequired  
  IpAddress as bsnDot11EssDhcpServerIpAddress  
  INTEGER as bsnDot11EssVpnContivityMode  
  IpAddress as bsnDot11EssVpnQotdServerAddress  
  Integer32 as bsnDot11EssBlacklistTimeout  
  Counter32 as bsnDot11EssNumberOfMobileStations  
  INTEGER as bsnDot11EssWebPassthru  
  INTEGER as bsnDot11EssCraniteSecurity  
  INTEGER as bsnDot11EssBlacklistingCapability  
  DisplayString as bsnDot11EssInterfaceName  
  DisplayString as bsnDot11EssAclName  
  INTEGER as bsnDot11EssAAAOverride  
  INTEGER as bsnDot11EssWepAllowSharedKeyAuth  
  INTEGER as bsnDot11EssFortressSecurity  
  INTEGER as bsnDot11EssL2tpSecurity  
  INTEGER as bsnDot11EssBroadcastSsid  
  INTEGER as bsnDot11EssExternalPolicyValidation  
  INTEGER as bsnDot11EssRSNSecurity  
  INTEGER as bsnDot11EssRSNWPACompatibilityMode  
  INTEGER as bsnDot11EssRSNAllowTKIPClients  
  INTEGER as bsnDot11EssRSNAuthKeyMgmtMode  
  OCTET STRING as bsnDot11EssRSNAuthPresharedKey  
  OCTET STRING as bsnDot11EssRSNAuthPresharedKeyHex  
  INTEGER as bsnDot11EssIPv6Bridging  
  RowStatus as bsnDot11EssRowStatus  
  INTEGER as bsnDot11EssWebPassthroughEmail  
  INTEGER as bsnDot11EssWmePolicySetting  
  INTEGER as bsnDot11Ess80211ePolicySetting  
  DisplayString as bsnDot11EssRadiusAuthPrimaryServer  
  DisplayString as bsnDot11EssRadiusAuthSecondaryServer  
  DisplayString as bsnDot11EssRadiusAuthTertiaryServer  
  DisplayString as bsnDot11EssRadiusAcctPrimaryServer  
  DisplayString as bsnDot11EssRadiusAcctSecondaryServer  
  INTEGER as bsnDot11Ess7920PhoneSupport  
  DisplayString as bsnDot11EssRadiusAcctTertiaryServer  

BsnDot11QosProfileEntry  
SEQUENCE    
  OCTET STRING as bsnDot11QosProfileName  
  OCTET STRING as bsnDot11QosProfileDesc  
  INTEGER as bsnDot11QosAverageDataRate  
  INTEGER as bsnDot11QosBurstDataRate  
  INTEGER as bsnDot11QosAvgRealTimeDataRate  
  INTEGER as bsnDot11QosBurstRealTimeDataRate  
  INTEGER as bsnDot11QosMaxRFUsagePerAP  
  INTEGER as bsnDot11QosProfileQueueDepth  
  INTEGER as bsnDot11WiredQosProtocol  
  INTEGER as bsnDot11802Dot1PTag  
  INTEGER as bsnDot11ResetProfileToDefault  

BsnMobileStationEntry  
SEQUENCE    
  MacAddress as bsnMobileStationMacAddress  
  IpAddress as bsnMobileStationIpAddress  
  DisplayString as bsnMobileStationUserName  
  MacAddress as bsnMobileStationAPMacAddr  
  INTEGER as bsnMobileStationAPIfSlotId  
  INTEGER as bsnMobileStationEssIndex  
  DisplayString as bsnMobileStationSsid  
  Unsigned32 as bsnMobileStationAID  
  INTEGER as bsnMobileStationStatus  
  INTEGER as bsnMobileStationReasonCode  
  INTEGER as bsnMobileStationMobilityStatus  
  IpAddress as bsnMobileStationAnchorAddress  
  INTEGER as bsnMobileStationCFPollable  
  INTEGER as bsnMobileStationCFPollRequest  
  INTEGER as bsnMobileStationChannelAgilityEnabled  
  INTEGER as bsnMobileStationPBCCOptionImplemented  
  INTEGER as bsnMobileStationShortPreambleOptionImplemented  
  Unsigned32 as bsnMobileStationSessionTimeout  
  INTEGER as bsnMobileStationAuthenticationAlgorithm  
  INTEGER as bsnMobileStationWepState  
  Unsigned32 as bsnMobileStationPortNumber  
  INTEGER as bsnMobileStationDeleteAction  
  DisplayString as bsnMobileStationPolicyManagerState  
  INTEGER as bsnMobileStationSecurityPolicyStatus  
  INTEGER as bsnMobileStationProtocol  
  INTEGER as bsnMobileStationMirrorMode  
  DisplayString as bsnMobileStationInterface  
  INTEGER as bsnMobileStationApMode  
  Integer32 as bsnMobileStationVlanId  
  INTEGER as bsnMobileStationPolicyType  
  INTEGER as bsnMobileStationEncryptionCypher  
  INTEGER as bsnMobileStationEapType  
  INTEGER as bsnMobileStationCcxVersion  
  INTEGER as bsnMobileStationE2eVersion  
  INTEGER as bsnMobileStationStatusCode  

BsnMobileStationByIpEntry  
SEQUENCE    
  IpAddress as bsnMobileStationByIpAddress  
  MacAddress as bsnMobileStationByIpMacAddress  

BsnMobileStationByUsernameEntry  
SEQUENCE    
  OCTET STRING as bsnMobileStationByUserName  
  MacAddress as bsnMobileStationByUserMacAddress  

BsnMobileStationPerRadioPerVapEntry  
SEQUENCE    
  Integer32 as bsnMobileStationPerRadioPerVapIndex  
  MacAddress as bsnMobileStationMacAddr  

BsnMobileStationStatsEntry  
SEQUENCE    
  Integer32 as bsnMobileStationRSSI  
  Counter64 as bsnMobileStationBytesReceived  
  Counter64 as bsnMobileStationBytesSent  
  Counter64 as bsnMobileStationPolicyErrors  
  Counter64 as bsnMobileStationPacketsReceived  
  Counter64 as bsnMobileStationPacketsSent  
  Integer32 as bsnMobileStationSnr  

BsnMobileStationExtStatsEntry  
SEQUENCE    
  Integer32 as bsnMobileStationSampleTime  
  Counter64 as bsnMobileStationTxExcessiveRetries  
  Counter64 as bsnMobileStationTxRetries  
  Counter64 as bsnMobileStationTxFiltered  

BsnMobileStationRssiDataEntry  
SEQUENCE    
  MacAddress as bsnMobileStationRssiDataApMacAddress  
  Unsigned32 as bsnMobileStationRssiDataApIfSlotId  
  INTEGER as bsnMobileStationRssiDataApIfType  
  DisplayString as bsnMobileStationRssiDataApName  
  Integer32 as bsnMobileStationRssiData  
  Unsigned32 as bsnAPIfPhyAntennaIndex  
  Counter32 as bsnMobileStationRssiDataLastHeard  

BsnTagEntry  
SEQUENCE    
  MacAddress as bsnTagDot11MacAddress  
  INTEGER as bsnTagType  
  Unsigned32 as bsnTagTimeInterval  
  INTEGER as bsnTagBatteryStatus  
  Unsigned32 as bsnTagLastReported  

BsnTagStatsEntry  
SEQUENCE    
  Unsigned32 as bsnTagBytesReceived  
  Unsigned32 as bsnTagPacketsReceived  

BsnTagRssiDataEntry  
SEQUENCE    
  MacAddress as bsnTagRssiDataApMacAddress  
  Unsigned32 as bsnTagRssiDataApIfSlotId  
  INTEGER as bsnTagRssiDataApIfType  
  DisplayString as bsnTagRssiDataApName  
  Counter32 as bsnTagRssiDataLastHeard  
  Integer32 as bsnTagRssiData  
  Integer32 as bsnTagRssiDataSnr  

BsnWatchListClientEntry  
SEQUENCE    
  OCTET STRING as bsnWatchListClientKey  
  INTEGER as bsnWatchListClientType  
  RowStatus as bsnWatchListClientRowStatus  

BsnRogueAPEntry  
SEQUENCE    
  MacAddress as bsnRogueAPDot11MacAddress  
  Integer32 as bsnRogueAPTotalDetectingAPs  
  DisplayString as bsnRogueAPFirstReported  
  DisplayString as bsnRogueAPLastReported  
  INTEGER as bsnRogueAPContainmentLevel  
  INTEGER as bsnRogueAPType  
  INTEGER as bsnRogueAPOnNetwork  
  Integer32 as bsnRogueAPTotalClients  
  RowStatus as bsnRogueAPRowStatus  
  Integer32 as bsnRogueAPMaxDetectedRSSI  
  DisplayString as bsnRogueAPSSID  
  INTEGER as bsnRogueAPState  

BsnRogueAPAirespaceAPEntry  
SEQUENCE    
  MacAddress as bsnRogueAPAirespaceAPMacAddress  
  Unsigned32 as bsnRogueAPAirespaceAPSlotId  
  INTEGER as bsnRogueAPRadioType  
  DisplayString as bsnRogueAPAirespaceAPName  
  Integer32 as bsnRogueAPChannelNumber  
  DisplayString as bsnRogueAPSsid  
  Integer32 as bsnRogueAPAirespaceAPRSSI  
  INTEGER as bsnRogueAPContainmentMode  
  Unsigned32 as bsnRogueAPContainmentChannelCount  
  DisplayString as bsnRogueAPContainmentChannels  
  Counter32 as bsnRogueAPAirespaceAPLastHeard  
  INTEGER as bsnRogueAPAirespaceAPWepMode  
  INTEGER as bsnRogueAPAirespaceAPPreamble  
  INTEGER as bsnRogueAPAirespaceAPWpaMode  
  Integer32 as bsnRogueAPAirespaceAPSNR  

BsnRogueClientPerRogueAPEntry  
SEQUENCE    
  MacAddress as bsnRogueAPDot11MacAddr  
  MacAddress as bsnRogueClientDot11MacAddr  

BsnRogueClientEntry  
SEQUENCE    
  MacAddress as bsnRogueClientDot11MacAddress  
  Integer32 as bsnRogueClientTotalDetectingAPs  
  DisplayString as bsnRogueClientFirstReported  
  DisplayString as bsnRogueClientLastReported  
  MacAddress as bsnRogueClientBSSID  
  INTEGER as bsnRogueClientContainmentLevel  
  Integer32 as bsnRogueClientLastHeard  
  INTEGER as bsnRogueClientState  

BsnRogueClientAirespaceAPEntry  
SEQUENCE    
  MacAddress as bsnRogueClientAirespaceAPMacAddress  
  Unsigned32 as bsnRogueClientAirespaceAPSlotId  
  INTEGER as bsnRogueClientRadioType  
  DisplayString as bsnRogueClientAirespaceAPName  
  Integer32 as bsnRogueClientChannelNumber  
  Integer32 as bsnRogueClientAirespaceAPRSSI  
  DisplayString as bsnRogueClientAirespaceAPLastHeard  
  Integer32 as bsnRogueClientAirespaceAPSNR  

BsnThirdPartyAPEntry  
SEQUENCE    
  MacAddress as bsnThirdPartyAPMacAddress  
  Integer32 as bsnThirdPartyAPInterface  
  IpAddress as bsnThirdPartyAPIpAddress  
  INTEGER as bsnThirdPartyAP802Dot1XRequired  
  INTEGER as bsnThirdPartyAPMirrorMode  
  RowStatus as bsnThirdPartyAPRowStatus  

BsnAPEntry  
SEQUENCE    
  MacAddress as bsnAPDot3MacAddress  
  INTEGER as bsnAPNumOfSlots  
  OCTET STRING as bsnAPName  
  IpAddress as bsnApIpAddress  
  OCTET STRING as bsnAPLocation  
  INTEGER as bsnAPMonitorOnlyMode  
  INTEGER as bsnAPOperationStatus  
  DisplayString as bsnAPSoftwareVersion  
  DisplayString as bsnAPBootVersion  
  OCTET STRING as bsnAPPrimaryMwarName  
  INTEGER as bsnAPReset  
  INTEGER as bsnAPStatsTimer  
  INTEGER as bsnAPPortNumber  
  DisplayString as bsnAPModel  
  DisplayString as bsnAPSerialNumber  
  INTEGER as bsnAPClearConfig  
  INTEGER as bsnAPMirrorMode  
  INTEGER as bsnAPRemoteModeSupport  
  INTEGER as bsnAPType  
  OCTET STRING as bsnAPSecondaryMwarName  
  OCTET STRING as bsnAPTertiaryMwarName  
  INTEGER as bsnAPIsStaticIP  
  IpAddress as bsnAPNetmask  
  IpAddress as bsnAPGateway  
  IpAddress as bsnAPStaticIPAddress  
  INTEGER as bsnAPBridgingSupport  
  OCTET STRING as bsnAPGroupVlanName  
  INTEGER as bsnAPAdminStatus  
  DisplayString as bsnAPIOSVersion  
  INTEGER as bsnAPCertificateType  
  MacAddress as bsnAPEthernetMacAddress  

BsnAPIfEntry  
SEQUENCE    
  Unsigned32 as bsnAPIfSlotId  
  INTEGER as bsnAPIfType  
  INTEGER as bsnAPIfPhyChannelAssignment  
  INTEGER as bsnAPIfPhyChannelNumber  
  INTEGER as bsnAPIfPhyTxPowerControl  
  INTEGER as bsnAPIfPhyTxPowerLevel  
  INTEGER as bsnAPIfPhyAntennaType  
  INTEGER as bsnAPIfPhyAntennaMode  
  INTEGER as bsnAPIfPhyAntennaDiversity  
  Unsigned32 as bsnAPIfCellSiteConfigId  
  INTEGER as bsnAPIfNumberOfVaps  
  INTEGER as bsnAPIfOperStatus  
  INTEGER as bsnAPIfPortNumber  
  INTEGER as bsnAPIfPhyAntennaOptions  
  Counter32 as bsnApIfNoOfUsers  
  INTEGER as bsnAPIfWlanOverride  
  INTEGER as bsnAPIfPacketsSniffingFeature  
  INTEGER as bsnAPIfSniffChannel  
  IpAddress as bsnAPIfSniffServerIPAddress  
  INTEGER as bsnAPIfAntennaGain  
  DisplayString as bsnAPIfChannelList  
  DisplayString as bsnAPIfAbsolutePowerList  
  INTEGER as bsnAPIfRegulatoryDomainSupport  
  INTEGER as bsnAPIfAdminStatus  

BsnAPIfWlanOverrideEntry  
SEQUENCE    
  Unsigned32 as bsnAPIfWlanOverrideId  
  DisplayString as bsnAPIfWlanOverrideSsid  
  RowStatus as bsnAPIfWlanOverrideRowStatus  

BsnAPIfSmtParamEntry  
SEQUENCE    
  INTEGER as bsnAPIfDot11BeaconPeriod  
  INTEGER as bsnAPIfDot11MediumOccupancyLimit  
  INTEGER as bsnAPIfDot11CFPPeriod  
  INTEGER as bsnAPIfDot11CFPMaxDuration  
  OCTET STRING as bsnAPIfDot11OperationalRateSet  
  INTEGER as bsnAPIfDot11DTIMPeriod  
  INTEGER as bsnAPIfDot11MultiDomainCapabilityImplemented  
  INTEGER as bsnAPIfDot11MultiDomainCapabilityEnabled  
  OCTET STRING as bsnAPIfDot11CountryString  
  INTEGER as bsnAPIfDot11SmtParamsConfigType  
  MacAddress as bsnAPIfDot11BSSID  

BsnAPIfMultiDomainCapabilityEntry  
SEQUENCE    
  Integer32 as bsnAPIfDot11MaximumTransmitPowerLevel  
  Integer32 as bsnAPIfDot11FirstChannelNumber  
  Integer32 as bsnAPIfDot11NumberofChannels  

BsnAPIfMacOperationParamEntry  
SEQUENCE    
  INTEGER as bsnAPIfDot11MacRTSThreshold  
  INTEGER as bsnAPIfDot11MacShortRetryLimit  
  INTEGER as bsnAPIfDot11MacLongRetryLimit  
  INTEGER as bsnAPIfDot11MacFragmentationThreshold  
  Unsigned32 as bsnAPIfDot11MacMaxTransmitMSDULifetime  
  INTEGER as bsnAPIfDot11MacParamsConfigType  
  Unsigned32 as bsnAPIfDot11MacMaxReceiveLifetime  

BsnAPIfDot11CountersEntry  
SEQUENCE    
  Counter32 as bsnAPIfDot11TransmittedFragmentCount  
  Counter32 as bsnAPIfDot11MulticastTransmittedFrameCount  
  Counter32 as bsnAPIfDot11RetryCount  
  Counter32 as bsnAPIfDot11MultipleRetryCount  
  Counter32 as bsnAPIfDot11FrameDuplicateCount  
  Counter32 as bsnAPIfDot11RTSSuccessCount  
  Counter32 as bsnAPIfDot11RTSFailureCount  
  Counter32 as bsnAPIfDot11ACKFailureCount  
  Counter32 as bsnAPIfDot11ReceivedFragmentCount  
  Counter32 as bsnAPIfDot11MulticastReceivedFrameCount  
  Counter32 as bsnAPIfDot11FCSErrorCount  
  Counter32 as bsnAPIfDot11TransmittedFrameCount  
  Counter32 as bsnAPIfDot11WEPUndecryptableCount  
  Counter32 as bsnAPIfDot11FailedCount  

BsnAPIfDot11PhyTxPowerEntry  
SEQUENCE    
  INTEGER as bsnAPIfDot11NumberSupportedPowerLevels  
  INTEGER as bsnAPIfDot11TxPowerLevel1  
  INTEGER as bsnAPIfDot11TxPowerLevel2  
  INTEGER as bsnAPIfDot11TxPowerLevel3  
  INTEGER as bsnAPIfDot11TxPowerLevel4  
  INTEGER as bsnAPIfDot11TxPowerLevel5  
  INTEGER as bsnAPIfDot11TxPowerLevel6  
  INTEGER as bsnAPIfDot11TxPowerLevel7  
  INTEGER as bsnAPIfDot11TxPowerLevel8  

BsnAPIfDot11PhyChannelEntry  
SEQUENCE    
  INTEGER as bsnAPIfDot11CurrentCCAMode  
  Integer32 as bsnAPIfDot11EDThreshold  
  Integer32 as bsnAPIfDot11TIThreshold  

BsnAPIfProfileThresholdConfigEntry  
SEQUENCE    
  INTEGER as bsnAPIfProfileParamAssignment  
  INTEGER as bsnAPIfForeignInterferenceThreshold  
  INTEGER as bsnAPIfForeignNoiseThreshold  
  INTEGER as bsnAPIfRFUtilizationThreshold  
  Unsigned32 as bsnAPIfThroughputThreshold  
  INTEGER as bsnAPIfMobilesThreshold  
  INTEGER as bsnAPIfCoverageThreshold  
  INTEGER as bsnAPIfMobileMinExceptionLevel  
  INTEGER as bsnAPIfCoverageExceptionLevel  

BsnAPIfLoadParametersEntry  
SEQUENCE    
  INTEGER as bsnAPIfLoadRxUtilization  
  INTEGER as bsnAPIfLoadTxUtilization  
  INTEGER as bsnAPIfLoadChannelUtilization  
  Integer32 as bsnAPIfLoadNumOfClients  
  Integer32 as bsnAPIfPoorSNRClients  

BsnAPIfChannelInterferenceInfoEntry  
SEQUENCE    
  Integer32 as bsnAPIfInterferenceChannelNo  
  Integer32 as bsnAPIfInterferencePower  
  INTEGER as bsnAPIfInterferenceUtilization  

BsnAPIfRadarChannelStatisticsEntry  
SEQUENCE    
  Integer32 as bsnAPIfRadarDetectedChannelNumber  
  Integer32 as bsnAPIfRadarSignalLastHeard  

BsnAPIfChannelNoiseInfoEntry  
SEQUENCE    
  Integer32 as bsnAPIfNoiseChannelNo  
  Integer32 as bsnAPIfDBNoisePower  

BsnAPIfProfileStateEntry  
SEQUENCE    
  ProfileState as bsnAPIfLoadProfileState  
  ProfileState as bsnAPIfInterferenceProfileState  
  ProfileState as bsnAPIfNoiseProfileState  
  ProfileState as bsnAPIfCoverageProfileState  

BsnAPIfRxNeighborsEntry  
SEQUENCE    
  MacAddress as bsnAPIfRxNeighborMacAddress  
  IpAddress as bsnAPIfRxNeighborIpAddress  
  Integer32 as bsnAPIfRxNeighborRSSI  
  Integer32 as bsnAPIfRxNeighborSlot  

BsnMeshNodeEntry  
SEQUENCE    
  INTEGER as bsnMeshNodeRole  
  OCTET STRING as bsnMeshNodeGroup  
  INTEGER as bsnMeshNodeBackhaul  
  INTEGER as bsnMeshNodeBackhaulPAP  
  INTEGER as bsnMeshNodeBackhaulRAP  
  Integer32 as bsnMeshNodeDataRate  
  Integer32 as bsnMeshNodeChannel  
  INTEGER as bsnMeshNodeRoutingState  
  Counter32 as bsnMeshNodeMalformedNeighPackets  
  Counter32 as bsnMeshNodePoorNeighSnr  
  Counter32 as bsnMeshNodeBlacklistPackets  
  Counter32 as bsnMeshNodeInsufficientMemory  
  Counter32 as bsnMeshNodeRxNeighReq  
  Counter32 as bsnMeshNodeRxNeighRsp  
  Counter32 as bsnMeshNodeTxNeighReq  
  Counter32 as bsnMeshNodeTxNeighRsp  
  Counter32 as bsnMeshNodeParentChanges  
  Counter32 as bsnMeshNodeNeighTimeout  
  MacAddress as bsnMeshNodeParentMacAddress  
  INTEGER as bsnMeshNodeAPType  
  INTEGER as bsnMeshNodeEthernetBridge  
  Integer32 as bsnMeshNodeHops  

BsnMeshNeighsEntry  
SEQUENCE    
  MacAddress as bsnMeshNeighMacAddress  
  INTEGER as bsnMeshNeighType  
  INTEGER as bsnMeshNeighState  
  Integer32 as bsnMeshNeighSnr  
  Integer32 as bsnMeshNeighSnrUp  
  Integer32 as bsnMeshNeighSnrDown  
  Integer32 as bsnMeshNeighLinkSnr  
  Integer32 as bsnMeshNeighAdjustedEase  
  Integer32 as bsnMeshNeighUnadjustedEase  
  Integer32 as bsnMeshNeighRapEase  
  Counter32 as bsnMeshNeighTxParent  
  Counter32 as bsnMeshNeighRxParent  
  Counter32 as bsnMeshNeighPoorSnr  
  Integer32 as bsnMeshNeighLastUpdate  
  Integer32 as bsnMeshNeighParentChange  

BsnAPIfStationRSSICoverageInfoEntry  
SEQUENCE    
  Integer32 as bsnAPIfStationRSSICoverageIndex  
  Integer32 as bsnAPIfRSSILevel  
  Integer32 as bsnAPIfStationCountOnRSSI  

BsnAPIfStationSNRCoverageInfoEntry  
SEQUENCE    
  Integer32 as bsnAPIfStationSNRCoverageIndex  
  Integer32 as bsnAPIfSNRLevel  
  Integer32 as bsnAPIfStationCountOnSNR  

BsnAPIfRecommendedRFParametersEntry  
SEQUENCE    
  Integer32 as bsnAPIfRecommendedChannelNumber  
  Integer32 as bsnAPIfRecommendedTxPowerLevel  
  Integer32 as bsnAPIfRecommendedRTSThreshold  
  Integer32 as bsnAPIfRecommendedFragmentationThreshold  

BsnStandardSignatureEntry  
SEQUENCE    
  Unsigned32 as bsnStandardSignaturePrecedence  
  DisplayString as bsnStandardSignatureName  
  DisplayString as bsnStandardSignatureDescription  
  INTEGER as bsnStandardSignatureFrameType  
  INTEGER as bsnStandardSignatureAction  
  INTEGER as bsnStandardSignatureState  
  Unsigned32 as bsnStandardSignatureFrequency  
  Unsigned32 as bsnStandardSignatureQuietTime  
  Unsigned32 as bsnStandardSignatureVersion  
  INTEGER as bsnStandardSignatureConfigType  
  RowStatus as bsnStandardSignatureRowStatus  
  TruthValue as bsnStandardSignatureEnable  
  BsnTxtSignatureMacInfo as bsnStandardSignatureMacInfo  
  Unsigned32 as bsnStandardSignatureMacFreq  

BsnStandardSignaturePatternEntry  
SEQUENCE    
  Unsigned32 as bsnStandardSignaturePatternIndex  
  Unsigned32 as bsnStandardSignaturePatternOffset  
  DisplayString as bsnStandardSignaturePatternString  
  DisplayString as bsnStandardSignaturePatternMask  
  BsnSignaturePatternOffSetStart as bsnStandardSignaturePatternOffSetStart  
  RowStatus as bsnStandardSignaturePatternRowStatus  

BsnCustomSignatureEntry  
SEQUENCE    
  Unsigned32 as bsnCustomSignaturePrecedence  
  DisplayString as bsnCustomSignatureName  
  DisplayString as bsnCustomSignatureDescription  
  INTEGER as bsnCustomSignatureFrameType  
  INTEGER as bsnCustomSignatureAction  
  INTEGER as bsnCustomSignatureState  
  Unsigned32 as bsnCustomSignatureFrequency  
  Unsigned32 as bsnCustomSignatureQuietTime  
  Unsigned32 as bsnCustomSignatureVersion  
  INTEGER as bsnCustomSignatureConfigType  
  RowStatus as bsnCustomSignatureRowStatus  
  TruthValue as bsnCustomSignatureEnable  
  BsnTxtSignatureMacInfo as bsnCustomSignatureMacInfo  
  Unsigned32 as bsnCustomSignatureMacFreq  

BsnCustomSignaturePatternEntry  
SEQUENCE    
  Unsigned32 as bsnCustomSignaturePatternIndex  
  Unsigned32 as bsnCustomSignaturePatternOffset  
  DisplayString as bsnCustomSignaturePatternString  
  DisplayString as bsnCustomSignaturePatternMask  
  RowStatus as bsnCustomSignaturePatternRowStatus  
  BsnSignaturePatternOffSetStart as bsnCustomSignaturePatternOffSetStart  

BsnWrasDot11aGroupEntry  
SEQUENCE    
  MacAddress as bsnWrasDot11aPeerMacAddress  
  IpAddress as bsnWrasDot11aPeerIpAddress  

BsnWrasDot11bGroupEntry  
SEQUENCE    
  MacAddress as bsnWrasDot11bPeerMacAddress  
  IpAddress as bsnWrasDot11bPeerIpAddress  

BsnRadiusAuthServerEntry  
SEQUENCE    
  Integer32 as bsnRadiusAuthServerIndex  
  IpAddress as bsnRadiusAuthServerAddress  
  Integer32 as bsnRadiusAuthClientServerPortNumber  
  OCTET STRING as bsnRadiusAuthServerKey  
  INTEGER as bsnRadiusAuthServerStatus  
  INTEGER as bsnRadiusAuthServerKeyFormat  
  INTEGER as bsnRadiusAuthServerRFC3576  
  INTEGER as bsnRadiusAuthServerIPSec  
  INTEGER as bsnRadiusAuthServerIPSecAuth  
  INTEGER as bsnRadiusAuthServerIPSecEncryption  
  INTEGER as bsnRadiusAuthServerIPSecIKEPhase1  
  Integer32 as bsnRadiusAuthServerIPSecIKELifetime  
  INTEGER as bsnRadiusAuthServerIPSecDHGroup  
  INTEGER as bsnRadiusAuthServerNetworkUserConfig  
  INTEGER as bsnRadiusAuthServerMgmtUserConfig  
  INTEGER as bsnRadiusAuthServerRetransmitTimeout  
  OCTET STRING as bsnRadiusAuthServerKeyWrapKEKkey  
  OCTET STRING as bsnRadiusAuthServerKeyWrapMACKkey  
  INTEGER as bsnRadiusAuthServerKeyWrapFormat  
  RowStatus as bsnRadiusAuthServerRowStatus  

BsnRadiusAccServerEntry  
SEQUENCE    
  Integer32 as bsnRadiusAccServerIndex  
  IpAddress as bsnRadiusAccServerAddress  
  Integer32 as bsnRadiusAccClientServerPortNumber  
  OCTET STRING as bsnRadiusAccServerKey  
  INTEGER as bsnRadiusAccServerStatus  
  INTEGER as bsnRadiusAccServerKeyFormat  
  INTEGER as bsnRadiusAccServerIPSec  
  INTEGER as bsnRadiusAccServerIPSecAuth  
  INTEGER as bsnRadiusAccServerIPSecEncryption  
  INTEGER as bsnRadiusAccServerIPSecIKEPhase1  
  Integer32 as bsnRadiusAccServerIPSecIKELifetime  
  INTEGER as bsnRadiusAccServerIPSecDHGroup  
  INTEGER as bsnRadiusAccServerNetworkUserConfig  
  INTEGER as bsnRadiusAccServerRetransmitTimeout  
  RowStatus as bsnRadiusAccServerRowStatus  

BsnRadiusAuthServerStatsEntry  
SEQUENCE    
  TimeTicks as bsnRadiusAuthClientRoundTripTime  
  Counter32 as bsnRadiusAuthClientAccessRequests  
  Counter32 as bsnRadiusAuthClientAccessRetransmissions  
  Counter32 as bsnRadiusAuthClientAccessAccepts  
  Counter32 as bsnRadiusAuthClientAccessRejects  
  Counter32 as bsnRadiusAuthClientAccessChallenges  
  Counter32 as bsnRadiusAuthClientMalformedAccessResponses  
  Counter32 as bsnRadiusAuthClientBadAuthenticators  
  Gauge32 as bsnRadiusAuthClientPendingRequests  
  Counter32 as bsnRadiusAuthClientTimeouts  
  Counter32 as bsnRadiusAuthClientUnknownTypes  
  Counter32 as bsnRadiusAuthClientPacketsDropped  

BsnRadiusAccServerStatsEntry  
SEQUENCE    
  TimeTicks as bsnRadiusAccClientRoundTripTime  
  Counter32 as bsnRadiusAccClientRequests  
  Counter32 as bsnRadiusAccClientRetransmissions  
  Counter32 as bsnRadiusAccClientResponses  
  Counter32 as bsnRadiusAccClientMalformedResponses  
  Counter32 as bsnRadiusAccClientBadAuthenticators  
  Gauge32 as bsnRadiusAccClientPendingRequests  
  Counter32 as bsnRadiusAccClientTimeouts  
  Counter32 as bsnRadiusAccClientUnknownTypes  
  Counter32 as bsnRadiusAccClientPacketsDropped  

BsnUsersEntry  
SEQUENCE    
  OCTET STRING as bsnUserName  
  OCTET STRING as bsnUserPassword  
  INTEGER as bsnUserEssIndex  
  INTEGER as bsnUserAccessMode  
  INTEGER as bsnUserType  
  OCTET STRING as bsnUserInterfaceName  
  RowStatus as bsnUserRowStatus  

BsnMacFilterEntry  
SEQUENCE    
  OCTET STRING as bsnMacFilterAddress  
  INTEGER as bsnMacFilterWlanId  
  OCTET STRING as bsnMacFilterInterfaceName  
  OCTET STRING as bsnMacFilterDescription  
  RowStatus as bsnMacFilterRowStatus  

BsnLocalNetUserEntry  
SEQUENCE    
  OCTET STRING as bsnLocalNetUserName  
  INTEGER as bsnLocalNetUserWlanId  
  OCTET STRING as bsnLocalNetUserPassword  
  OCTET STRING as bsnLocalNetUserDescription  
  TimeInterval as bsnLocalNetUserLifetime  
  TimeTicks as bsnLocalNetUserStartTime  
  TimeInterval as bsnLocalNetUserRemainingTime  
  RowStatus as bsnLocalNetUserRowStatus  

BsnLocalManagementUserEntry  
SEQUENCE    
  OCTET STRING as bsnLocalManagementUserName  
  OCTET STRING as bsnLocalManagementUserPassword  
  INTEGER as bsnLocalManagementUserAccessMode  
  RowStatus as bsnLocalManagementUserRowStatus  

BsnAclEntry  
SEQUENCE    
  OCTET STRING as bsnAclName  
  INTEGER as bsnAclApplyMode  
  RowStatus as bsnAclRowStatus  

BsnAclRuleEntry  
SEQUENCE    
  Unsigned32 as bsnAclRuleIndex  
  INTEGER as bsnAclRuleAction  
  INTEGER as bsnAclRuleDirection  
  IpAddress as bsnAclRuleSourceIpAddress  
  IpAddress as bsnAclRuleSourceIpNetmask  
  IpAddress as bsnAclRuleDestinationIpAddress  
  IpAddress as bsnAclRuleDestinationIpNetmask  
  Unsigned32 as bsnAclRuleProtocol  
  Unsigned32 as bsnAclRuleStartSourcePort  
  Unsigned32 as bsnAclRuleEndSourcePort  
  Unsigned32 as bsnAclRuleStartDestinationPort  
  Unsigned32 as bsnAclRuleEndDestinationPort  
  Unsigned32 as bsnAclRuleDscp  
  Unsigned32 as bsnAclNewRuleIndex  
  RowStatus as bsnAclRuleRowStatus  

BsnBlackListClientEntry  
SEQUENCE    
  OCTET STRING as bsnBlackListClientMacAddress  
  OCTET STRING as bsnBlackListClientDescription  
  RowStatus as bsnBlackListClientRowStatus  

BsnExternalPolicyServerEntry  
SEQUENCE    
  Integer32 as bsnExternalPolicyServerIndex  
  IpAddress as bsnExternalPolicyServerAddress  
  Integer32 as bsnExternalPolicyServerPortNumber  
  OCTET STRING as bsnExternalPolicyServerKey  
  INTEGER as bsnExternalPolicyServerAdminStatus  
  INTEGER as bsnExternalPolicyServerConnectionStatus  
  RowStatus as bsnExternalPolicyServerRowStatus  

BsnAPAuthorizationEntry  
SEQUENCE    
  OCTET STRING as bsnAPAuthMacAddress  
  INTEGER as bsnAPAuthCertificateType  
  OCTET STRING as bsnAPAuthHashKey  
  RowStatus as bsnAPAuthRowStatus  

BsnWrasIpsecCertEntry  
SEQUENCE    
  DisplayString as bsnWrasIpsecCertName  
  OCTET STRING as bsnWrasIpsecCertificateUpdate  
  OCTET STRING as bsnWrasIpsecCertificate  
  OCTET STRING as bsnWrasIpsecCertPassword  
  RowStatus as bsnWrasIpsecCertStatus  

BsnPingTestEntry  
SEQUENCE    
  Integer32 as bsnPingTestId  
  IpAddress as bsnPingTestIPAddress  
  Integer32 as bsnPingTestSendCount  
  Integer32 as bsnPingTestReceivedCount  
  INTEGER as bsnPingTestStatus  
  RowStatus as bsnPingTestRowStatus  

BsnLinkTestEntry  
SEQUENCE    
  Integer32 as bsnLinkTestId  
  MacAddress as bsnLinkTestMacAddress  
  Integer32 as bsnLinkTestSendPktCount  
  Integer32 as bsnLinkTestSendPktLength  
  Integer32 as bsnLinkTestReceivedPktCount  
  Integer32 as bsnLinkTestClientRSSI  
  Integer32 as bsnLinkTestLocalSNR  
  Integer32 as bsnLinkTestLocalRSSI  
  INTEGER as bsnLinkTestStatus  
  RowStatus as bsnLinkTestRowStatus  

BsnMobilityGroupMembersEntry  
SEQUENCE    
  MacAddress as bsnMobilityGroupMemberMacAddress  
  IpAddress as bsnMobilityGroupMemberIPAddress  
  DisplayString as bsnMobilityGroupMemberGroupName  
  RowStatus as bsnMobilityGroupMemberRowStatus  

BsnMobilityAnchorsEntry  
SEQUENCE    
  DisplayString as bsnMobilityAnchorWlanSsid  
  IpAddress as bsnMobilityAnchorSwitchIPAddress  
  RowStatus as bsnMobilityAnchorRowStatus  

BsnMobilityGroupDirectoryEntry  
SEQUENCE    
  IpAddress as bsnGroupDirectoryMemberIPAddress  
  MacAddress as bsnGroupDirectoryMemberMacAddress  
  INTEGER as bsnGroupDirectoryDicoveryType  
  Counter32 as bsnMemberCurrentAnchoredClients  
  Counter32 as bsnMemberTotalAnchoredClients  
  Counter32 as bsnMemberCurrentExportedClients  
  Counter32 as bsnMemberTotalExportedClients  
  Counter32 as bsnMemberCurrentImportedClients  
  Counter32 as bsnMemberTotalImportedClients  
  Counter32 as bsnMemberTotalHandoffErrors  
  Counter32 as bsnMemberTotalCommunicationErrors  

BsnAPGroupsVlanEntry  
SEQUENCE    
  OCTET STRING as bsnAPGroupsVlanName  
  OCTET STRING as bsnAPGroupsVlanDescription  
  RowStatus as bsnAPGroupsVlanRowStatus  

BsnAPGroupsVlanMappingEntry  
SEQUENCE    
  DisplayString as bsnAPGroupsVlanMappingSsid  
  OCTET STRING as bsnAPGroupsVlanMappingInterfaceName  
  RowStatus as bsnAPGroupsVlanMappingRowStatus