ALC-OPT-MIB

File: ALC-OPT-MIB.mib (108108 bytes)

Imported modules

RFC1155-SMI RFC-1212

Imported symbols

Counter Gauge enterprises
OBJECT-TYPE

Defined Objects

codex 1.3.6.1.4.1.449
OBJECT IDENTIFIER    

cdxProductSpecific 1.3.6.1.4.1.449.2
OBJECT IDENTIFIER    

cdx6500 1.3.6.1.4.1.449.2.1
OBJECT IDENTIFIER    

cdx6500Configuration 1.3.6.1.4.1.449.2.1.2
OBJECT IDENTIFIER    

cdx6500CfgProtocolGroup 1.3.6.1.4.1.449.2.1.2.1
OBJECT IDENTIFIER    

cdx6500PCTPortProtocolGroup 1.3.6.1.4.1.449.2.1.2.1.1
OBJECT IDENTIFIER    

cdx6500PPCTALCCfgTable 1.3.6.1.4.1.449.2.1.2.1.1.27
OBJECT IDENTIFIER    

cdx6500PPCTALCPortTable 1.3.6.1.4.1.449.2.1.2.1.1.27.1
This table contains ALC Port configuration parameters
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCPortEntry

cdx6500PPCTALCPortEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1
Entries in the ALC Port Configuration Table.
OBJECT-TYPE    
  Cdx6500PPCTALCPortEntry  

alcPCfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcPCfgPortType 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.2
Port Type of this port.
OBJECT-TYPE    
  INTEGER alc(31)  

alcPCfgSubtype 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.3
This is the ALC port subtype. alcHpad - Host PAD. alcTpad - Terminal PAD.
OBJECT-TYPE    
  INTEGER alcHpad(1), alcTpad(2)  

alcPCfgPortControl 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.4
Specify any of the following port control options: simp : Simple connection with no control signal handshake. dtr : Connection with DTR control signal handshake. emri : Port emulates a modem and does dial-in/out handshake with RI. emdc : Port emulates a modem and does dial-in/out handshake with DCD. alcDte : DTE emulation with RTS/CTS handshake.
OBJECT-TYPE    
  INTEGER simp(1), emri(4), emdc(5), dtr(13), alcDte(15)  

alcPCfgClockSource 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.5
int : Internal clock source. ext : External clock source.
OBJECT-TYPE    
  INTEGER int(1), ext(2)  

alcPCfgClockSpeed 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.6
This is the speed of the port in bits per second, when using internal clocking.
OBJECT-TYPE    
  INTEGER clkspd1200(1), clkspd2400(2), clkspd4800(3), clkspd9600(4), clkspd19200(5), clkspd38400(6)  

alcPCfgPollDelayTimer 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.7
This is the delay in milliseconds to impose between poll cycles if no interchanges are polled. Valid on TPAD lines only.
OBJECT-TYPE    
  INTEGER 50..100000  

alcPCfgHostTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.8
On a poll coerced line, the host is considered to be down if a poll is not received within this time, specified in milliseconds. Valid on HPAD lines only.
OBJECT-TYPE    
  INTEGER 50..10000  

alcPCfgMaxMesgSize 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.9
This specifies the maximum size of messages that can be sent or received on this line excluding padding characters. TPAD may receive multiple messages in a frame, HPAD may transmit multiple messages in a frame.
OBJECT-TYPE    
  INTEGER 10..10000  

alcPCfgMinIntrvlBetweenPolls 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.10
The minimum length of time, in milliseconds, between polls issued on this line. Valid on TPAD lines only.
OBJECT-TYPE    
  INTEGER 0..100000  

alcPCfgRtsCtsTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.11
The time in milliseconds, within which CTS must be raised following the RTS signal.
OBJECT-TYPE    
  INTEGER 50..10000  

alcPCfgLeadPadChar 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.12
This is the character to use when inserting leading padding characters.
OBJECT-TYPE    
  OCTET STRING  

alcPCfgNumLeadPadChars 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.13
This is the number of leading padding characters to use.
OBJECT-TYPE    
  INTEGER 0..100  

alcPCfgTrailPadChar 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.14
This is the character to use when inserting trailing padding characters.
OBJECT-TYPE    
  OCTET STRING  

alcPCfgNumTrailPadChars 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.15
This is the number of trailing padding characters to use.
OBJECT-TYPE    
  INTEGER 0..100  

alcPCfgALCLineOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.16
Select options on this ALC port as follows: NONE : no option specified EMB_SYNC : Sychronization characters are inserted between messages in the same frame. MASK8 : Indicates that the `8' bit is treated as zero when examining interchange addresses on this line. COERCE : Poll coercion is used. CLASH : Poll responses will be aborted if a poll is received whilst a response to a previous poll is being transmitted. RFRTM : Responses will be generated to Response and Forward RTM messages. RZRTM : Responses will be generated to enquiry RTM messages. SOFT_SYNC : Selects software synchronization. NULLS : Nulls are allowed in the data stream. BACKTOBACK : Frames may be received back to back. Any combination of the above maybe specified by summing (e.g. NULLS+BACKTOBACK. . .).
OBJECT-TYPE    
  DisplayString SIZE(4..71)  

alcPCfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.17
none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcPCfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.18
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..8)  

alcPCfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.19
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

alcPCfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.20
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
OBJECT-TYPE    
  DisplayString SIZE(2..47)  

alcPCfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.21
This defines the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
OBJECT-TYPE    
  INTEGER 1..1000  

alcPCfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.22
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcPCfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.23
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcPCfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.24
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
OBJECT-TYPE    
  INTEGER 1..1000  

alcPCfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.25
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
OBJECT-TYPE    
  INTEGER 0..1000  

alcPCfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.26
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
OBJECT-TYPE    
  INTEGER 0..1000  

alcPCfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.27
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcPCfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.28
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
OBJECT-TYPE    
  DisplayString SIZE(3..32)  

alcPCfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.29
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

alcPCfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.30
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

cdx6500PPCTALCInterchangeTable 1.3.6.1.4.1.449.2.1.2.1.1.27.2
This table contains ALC Interchange configuration parameters
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCInterchangeEntry

cdx6500PPCTALCInterchangeEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1
Entries in the ALC Interchange Configuration Table.
OBJECT-TYPE    
  Cdx6500PPCTALCInterchangeEntry  

alcICfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcICfgInterchangeAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcICfgOptionOnInvalidCCC 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.3
The action to be taken on receipt of a message with an invalid ccc. discard : Discard the message ignore : Treat the message as correct. reenter : (TPAD only) The configured `re-enter' message is sent to the terminal. resend : (TPAD only) A resend request message is sent to the terminal.
OBJECT-TYPE    
  INTEGER discard(2), resend(3), reenter(4), ignore(5)  

alcICfgGenTerminalAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.4
Specifies the terminal address to which broadcast messages are sent when the GTA option is specified.
OBJECT-TYPE    
  OCTET STRING  

alcICfgHostTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.5
The host is considered to be down if a poll is not received within this period, which is specified in milliseconds.
OBJECT-TYPE    
  INTEGER 50..100000  

alcICfgMaxComponentsPerFrame 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.6
Specifies the maximum number of message segments transmitted in one frame (HPAD) or expected in one frame (TPAD).
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgFastPollCycleCount 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.7
The polling rate for an interchange in fast poll. A poll is issued to this interchange once in every n poll cycles on the line.
OBJECT-TYPE    
  INTEGER 1..255  

alcICfgSlowPollCycleCount 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.8
The polling rate for an interchange in slow poll. One slow poll IA is polled every n poll cycles on the line.
OBJECT-TYPE    
  INTEGER 1..255  

alcICfgN1Counter 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.9
The number of polls that can be sent without receiving a response before the interchange enters slow poll.
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgN2Counter 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.10
The number of good poll responses required before the interchange enters fast poll.
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgT1Timeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.11
The time, in milliseconds, within which an interchange must start responding to a poll.
OBJECT-TYPE    
  INTEGER 100..100000  

alcICfgT2Timeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.12
The time, in milliseconds, within which an interchange must complete its transmission.
OBJECT-TYPE    
  INTEGER 100..100000  

alcICfgReenterMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.13
This specifies the text of a message sent to terminals when a message with an incorrect ccc is received and the action on receipt of an invalid ccc is REENTER. Note that some terminals may require control characters at the start of the message.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

alcICfgStartMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.14
This specifies the text of a message sent to terminals when polling of this interchange is started and the STST option is configured. Note that some terminals may require control characters at the start of the message.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

alcICfgStopMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.15
This specifies the text of a message sent to terminals when polling of this interchange is stopped and the STST option is configured. Note that some terminals may require control characters at the start of the message.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

alcICfgOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.16
Select options on this ALC Interchange as follows : NONE : no option specified GTA : (TPAD only) Indicates that there is a general terminal address which may be used for broadcasting to all terminals on the interchange. NOPOLL : (TPAD only) Indicates that this interchange is not to be polled. RESET : Indicates that the interchange is capable of handling ALC Reset messages. STST : (TPAD only) Indicates that the configured start and stop messages should be transmitted when polling is started or stopped. Any combination of the above maybe specified by summing (e.g. GTA+NOPOLL+. . .).
OBJECT-TYPE    
  DisplayString SIZE(3..21)  

alcICfgValidTAList 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.17
A list of hexadecimal numbers between 1 and 3F separated by commas. /f or /r after each is used to indicate forward or reverse abort respectively. Ranges may be specified by separating two addresses by a dash `-'. Note that the addresses 0D, 1D, 2D, 3D and 3F are illegal. The list of terminal addresses that may be configured on the line, including the forward or reverse abort settings for each terminal.
OBJECT-TYPE    
  DisplayString  

alcICfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.18
none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcICfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.19
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..8)  

alcICfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.20
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

alcICfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.21
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
OBJECT-TYPE    
  DisplayString SIZE(2..47)  

alcICfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.22
This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
OBJECT-TYPE    
  INTEGER 1..1000  

alcICfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.23
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcICfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.24
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcICfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.25
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
OBJECT-TYPE    
  INTEGER 1..1000  

alcICfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.26
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
OBJECT-TYPE    
  INTEGER 0..1000  

alcICfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.27
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
OBJECT-TYPE    
  INTEGER 0..1000  

alcICfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.28
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcICfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.29
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
OBJECT-TYPE    
  DisplayString SIZE(3..32)  

alcICfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.30
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

alcICfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.31
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

cdx6500PPCTALCTerminalTable 1.3.6.1.4.1.449.2.1.2.1.1.27.3
This table contains ALC Terminal configuration parameters
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCTerminalEntry

cdx6500PPCTALCTerminalEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1
Entries in the ALC Terminal Configuration Table.
OBJECT-TYPE    
  Cdx6500PPCTALCTerminalEntry  

alcTCfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcTCfgInterchangeAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTCfgTerminalAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.3
Address identifying this terminal.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTCfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.4
none : No connection type. x25 : Connection type is X.25. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcTCfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.5
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..8)  

alcTCfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.6
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

alcTCfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.7
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
OBJECT-TYPE    
  DisplayString SIZE(2..47)  

alcTCfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.8
This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
OBJECT-TYPE    
  INTEGER 1..1000  

alcTCfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.9
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcTCfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.10
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
OBJECT-TYPE    
  DisplayString SIZE(2..53)  

alcTCfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.11
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
OBJECT-TYPE    
  INTEGER 1..1000  

alcTCfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.12
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
OBJECT-TYPE    
  INTEGER 0..1000  

alcTCfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.13
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
OBJECT-TYPE    
  INTEGER 0..1000  

alcTCfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.14
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcTCfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.15
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
OBJECT-TYPE    
  DisplayString SIZE(3..32)  

alcTCfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.16
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

alcTCfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.17
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
OBJECT-TYPE    
  DisplayString SIZE(0..62)  

cdx6500Statistics 1.3.6.1.4.1.449.2.1.3
OBJECT IDENTIFIER    

cdx6500StatProtocolGroup 1.3.6.1.4.1.449.2.1.3.1
OBJECT IDENTIFIER    

cdx6500PSTPortProtocolGroup 1.3.6.1.4.1.449.2.1.3.1.1
OBJECT IDENTIFIER    

cdx6500PPSTALCStatsTable 1.3.6.1.4.1.449.2.1.3.1.1.28
OBJECT IDENTIFIER    

cdx6500PPSTALCPortTable 1.3.6.1.4.1.449.2.1.3.1.1.28.1
This table contains ALC Port Statistics parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCPortEntry

cdx6500PPSTALCPortEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1
Entries in the ALC Port Statistics Table.
OBJECT-TYPE    
  Cdx6500PPSTALCPortEntry  

alcPStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcPStatsPortType 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.2
Port type of this port.
OBJECT-TYPE    
  INTEGER alc(31)  

alcPStatsPortState 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.3
Current Port State. connecting:The line has been enabled by the operator, but polling has not yet been established. online :The line is active. offline :The line has been disabled by the operator. pending :The line is inactive because of conditions detected by ALP PAD (X.25 virtual circuit not active). timedOut :The line is not being polled. This will be displayed on poll coerced HPAD lines only. flowCtrl :The application (ALP PAD) has imposed flow control on the line. na :Value not Available
OBJECT-TYPE    
  INTEGER offline(1), online(2), timedOut(7), pending(8), connecting(9), flowCtrl(11), na(100)  

alcPStatsFramesIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.4
Number of frames received.
OBJECT-TYPE    
  Counter  

alcPStatsFramesOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.5
Number of frames transmitted.
OBJECT-TYPE    
  Counter  

alcPStatsDataMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.6
Number of data messages received.
OBJECT-TYPE    
  Counter  

alcPStatsDataMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.7
Number of data messages transmitted.
OBJECT-TYPE    
  Counter  

alcPStatsCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.8
Number of characters received.
OBJECT-TYPE    
  Counter  

alcPStatsCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.9
Number of characters transmitted.
OBJECT-TYPE    
  Counter  

alcPStatsPolls 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.10
Number of polls transmitted or received.
OBJECT-TYPE    
  Counter  

alcPStatsGAs 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.11
Number of Go Ahead messages transmitted or received.
OBJECT-TYPE    
  Counter  

alcPStatsResets 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.12
Number of Reset messages transmitted or received.
OBJECT-TYPE    
  Counter  

alcPStatsDiscardBadIAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.13
Number of received messages discarded due to bad Interchange Address.
OBJECT-TYPE    
  Counter  

alcPStatsDiscardBadIAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.14
Number of transmitted messages discarded due to bad Interchange Address.
OBJECT-TYPE    
  Counter  

alcPStatsMaxQSizeOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.15
Maximum transmit queue size.
OBJECT-TYPE    
  INTEGER  

alcPStatsCCCErrors 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.16
Number of messages received with an invalid checksum.
OBJECT-TYPE    
  Counter  

alcPStatsSignalLosses 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.17
Number of Signal Losses.
OBJECT-TYPE    
  Counter  

alcPStatsOverlengthFrames 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.18
Number of overlength frames received.
OBJECT-TYPE    
  Counter  

alcPStatsPortStatus 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.19
Current Port Status. na :Value not Available
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), busyOut(3), up(4), down(5), na(100)  

alcPStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.20
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcPStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.21
The number of messages received from ALC.
OBJECT-TYPE    
  Counter  

alcPStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.22
The number of messages transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcPStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.23
The number of messages received from X.25.
OBJECT-TYPE    
  Counter  

alcPStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.24
The number of messages transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcPStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.25
The number of characters received from ALC.
OBJECT-TYPE    
  Counter  

alcPStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.26
The number of characters transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcPStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.27
The number of characters received from X.25.
OBJECT-TYPE    
  Counter  

alcPStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.28
The number of characters transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcPStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.29
The number of messages received by ALC for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.30
The number of messages received by X.25 for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.31
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.32
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.33
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
OBJECT-TYPE    
  Counter  

alcPStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.34
The number of messages discarded because the ALC outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.35
The number of messages discarded because the X.25 outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcPStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.36
The number of messages currently queued in the ALC outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcPStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.37
The number of messages currently queued in the X.25 outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcPStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.38
The maximum (highwater mark) size of the ALC outbound queue so far.
OBJECT-TYPE    
  INTEGER  

alcPStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.39
The maximum (highwater mark) size of the X.25 outbound queue so far.
OBJECT-TYPE    
  INTEGER  

cdx6500PPSTALCInterchangeTable 1.3.6.1.4.1.449.2.1.3.1.1.28.2
This table contains ALC Interchange Statistics parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCInterchangeEntry

cdx6500PPSTALCInterchangeEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1
Entries in the ALC Interchange Statistics Table.
OBJECT-TYPE    
  Cdx6500PPSTALCInterchangeEntry  

alcIStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcIStatsInterchangeAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcIStatsInterchangeState 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.3
Current State of this Interchange. online :The interchange is active. This is displayed for HPAD interchanges, and TPAD interchanges configured as NOPOLL, only. offline :The interchange has been disabled by the operator. pending :The interchange is inactive because of conditions detected by the application (ALP PAD). failed :The line with which this interchange is associated is down. timedOut:The interchange is not being polled. This is displayed for HPAD interchanges on non poll-coerced lines only. flowCtrl:The application (ALP PAD) has imposed flow control on the interchange. stopped :The line with which this interchange is associated is in the FLOW CONTROL state. This is valid for TPAD interchanges only. slowPoll:The interchange is in slow poll. fastPoll:The interchange is in fast poll. na :Value not Available
OBJECT-TYPE    
  INTEGER offline(1), online(2), fastPoll(3), slowPoll(4), stopped(6), timedOut(7), pending(8), failed(10), flowCtrl(11), na(100)  

alcIStatsFramesIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.4
Number of ALC frames received.
OBJECT-TYPE    
  Counter  

alcIStatsFramesOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.5
Number of ALC frames transmitted.
OBJECT-TYPE    
  Counter  

alcIStatsDataMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.6
Number of ALC data messages received.
OBJECT-TYPE    
  Counter  

alcIStatsDataMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.7
Number of ALC data messages transmitted.
OBJECT-TYPE    
  Counter  

alcIStatsCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.8
Total number of characters received, excluding synchronization characters.
OBJECT-TYPE    
  Counter  

alcIStatsCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.9
Total number of characters transmitted, excluding synchronization characters.
OBJECT-TYPE    
  Counter  

alcIStatsPolls 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.10
The number of poll messages transmitted for a line defined as a TPAD. The number received for one defined as HPAD.
OBJECT-TYPE    
  Counter  

alcIStatsGAs 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.11
The number of Go Ahead messages transmitted for a line defined as HPAD. The number received for one defined as TPAD.
OBJECT-TYPE    
  Counter  

alcIStatsResets 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.12
The number of Reset messages transmitted for a line defined as TPAD. The number received for one defined as HPAD.
OBJECT-TYPE    
  Counter  

alcIStatsDiscardBadTAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.13
The number of received messages discarded because the Terminal Address was not defined.
OBJECT-TYPE    
  Counter  

alcIStatsDiscardBadTAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.14
The number of transmitted messages discarded because the Terminal Address was not defined.
OBJECT-TYPE    
  Counter  

alcIStatsDisabledIAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.15
The number of received messages discarded because the Interchange was disabled.
OBJECT-TYPE    
  Counter  

alcIStatsDisabledIAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.16
The number of transmitted messages discarded because the Interchange was disabled.
OBJECT-TYPE    
  Counter  

alcIStatsMaxQSizeOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.17
Maximum number of frames queued for transmission.
OBJECT-TYPE    
  INTEGER  

alcIStatsCCCErrors 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.18
Number of messages received with an invalid checksum.
OBJECT-TYPE    
  Counter  

alcIStatsT1Timeouts 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.19
Number of T1 timer expirations. This is defined for TPAD only.
OBJECT-TYPE    
  Counter  

alcIStatsT2Timeouts 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.20
Number of T2 timer expirations. This is defined for TPAD only.
OBJECT-TYPE    
  Counter  

alcIStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.21
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcIStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.22
The number of messages received from ALC.
OBJECT-TYPE    
  Counter  

alcIStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.23
The number of messages transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcIStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.24
The number of messages received from X.25.
OBJECT-TYPE    
  Counter  

alcIStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.25
The number of messages transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcIStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.26
The number of characters received from ALC.
OBJECT-TYPE    
  Counter  

alcIStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.27
The number of characters transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcIStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.28
The number of characters received from X.25.
OBJECT-TYPE    
  Counter  

alcIStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.29
The number of characters transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcIStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.30
The number of messages received by ALC for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.31
The number of messages received by X.25 for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.32
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.33
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.34
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
OBJECT-TYPE    
  Counter  

alcIStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.35
The number of messages discarded because the ALC outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.36
The number of messages discarded because the X.25 outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcIStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.37
The number of messages currently queued in the ALC outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcIStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.38
The number of messages currently queued in the X.25 outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcIStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.39
The maximum (highwater mark) size of the ALC outbound queue so far.
OBJECT-TYPE    
  INTEGER  

alcIStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.40
The maximum (highwater mark) size of the X.25 outbound queue so far.
OBJECT-TYPE    
  INTEGER  

cdx6500PPSTALCTerminalTable 1.3.6.1.4.1.449.2.1.3.1.1.28.3
This table contains ALC Terminalinal Statistics parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCTerminalEntry

cdx6500PPSTALCTerminalEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1
Entries in the ALC Terminalinal Statistics Table.
OBJECT-TYPE    
  Cdx6500PPSTALCTerminalEntry  

alcTStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.1
Port number of this port.
OBJECT-TYPE    
  INTEGER 1..54  

alcTStatsInterchangeAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTStatsTerminalAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.3
Address identifying this terminal.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.4
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcTStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.5
The number of messages received from ALC.
OBJECT-TYPE    
  Counter  

alcTStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.6
The number of messages transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcTStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.7
The number of messages received from X.25.
OBJECT-TYPE    
  Counter  

alcTStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.8
The number of messages transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcTStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.9
The number of characters received from ALC.
OBJECT-TYPE    
  Counter  

alcTStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.10
The number of characters transmitted to ALC.
OBJECT-TYPE    
  Counter  

alcTStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.11
The number of characters received from X.25.
OBJECT-TYPE    
  Counter  

alcTStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.12
The number of characters transmitted to X.25.
OBJECT-TYPE    
  Counter  

alcTStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.13
The number of messages received by ALC for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.14
The number of messages received by X.25 for which the destination entity is unable to process the data.
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.15
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.16
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.17
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
OBJECT-TYPE    
  Counter  

alcTStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.18
The number of messages discarded because the ALC outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.19
The number of messages discarded because the X.25 outbound message queue was full.
OBJECT-TYPE    
  Counter  

alcTStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.20
The number of messages currently queued in the ALC outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcTStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.21
The number of messages currently queued in the X.25 outbound message queue for transmission.
OBJECT-TYPE    
  INTEGER  

alcTStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.22
The maximum (highwater mark) size of the ALC outbound queue so far.
OBJECT-TYPE    
  INTEGER  

alcTStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.23
The maximum (highwater mark) size of the X.25 outbound queue so far.
OBJECT-TYPE    
  INTEGER  

cdx6500Controls 1.3.6.1.4.1.449.2.1.4
OBJECT IDENTIFIER    

cdx6500ContALC 1.3.6.1.4.1.449.2.1.4.10
OBJECT IDENTIFIER    

cdx6500ContALCPortTable 1.3.6.1.4.1.449.2.1.4.10.1
This table contains ALC Port Control parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCPortEntry

cdx6500ContALCPortEntry 1.3.6.1.4.1.449.2.1.4.10.1.1
Entries in the ALC Port Control Table.
OBJECT-TYPE    
  Cdx6500ContALCPortEntry  

alcPContPortNumber 1.3.6.1.4.1.449.2.1.4.10.1.1.1
ALC Port Number.
OBJECT-TYPE    
  INTEGER 1..54  

alcPContPortBoot 1.3.6.1.4.1.449.2.1.4.10.1.1.2
Boots the specified ALC Port. boot - Boot the port. noBoot - Do not boot the port.
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcPContPortEnable 1.3.6.1.4.1.449.2.1.4.10.1.1.3
Enables the specified ALC Port. enable - Enable the port. noEnable - Do not enable the port.
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcPContPortDisable 1.3.6.1.4.1.449.2.1.4.10.1.1.4
Disables the specified ALC Port. disable - Disable the port. noDisable - Do not disable the port.
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

cdx6500ContALCInterchangeTable 1.3.6.1.4.1.449.2.1.4.10.2
This table contains ALC Interchange Control parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCInterchangeEntry

cdx6500ContALCInterchangeEntry 1.3.6.1.4.1.449.2.1.4.10.2.1
Entries in the ALC Interchange Control Table.
OBJECT-TYPE    
  Cdx6500ContALCInterchangeEntry  

alcIContPortNumber 1.3.6.1.4.1.449.2.1.4.10.2.1.1
ALC Port Number.
OBJECT-TYPE    
  INTEGER 1..54  

alcIContInterchangeAddress 1.3.6.1.4.1.449.2.1.4.10.2.1.2
ALC Interchange address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcIContInterchangeBoot 1.3.6.1.4.1.449.2.1.4.10.2.1.3
Boots the specified ALC Interchange. boot - Boot the interchange. noBoot - Do not boot the interchange.
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcIContInterchangeEnable 1.3.6.1.4.1.449.2.1.4.10.2.1.4
Enables the specified ALC Interchange. enable - Enable the interchange. noEnable - Do not enable the interchange.
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcIContInterchangeDisable 1.3.6.1.4.1.449.2.1.4.10.2.1.5
Disables the specified ALC Interchange. disable - Disable the interchange. noDisable - Do not disable the interchange.
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

cdx6500ContALCTerminalTable 1.3.6.1.4.1.449.2.1.4.10.3
This table contains ALC Terminal Control parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCTerminalEntry

cdx6500ContALCTerminalEntry 1.3.6.1.4.1.449.2.1.4.10.3.1
Entries in the ALC Terminal Control Table.
OBJECT-TYPE    
  Cdx6500ContALCTerminalEntry  

alcTContPortNumber 1.3.6.1.4.1.449.2.1.4.10.3.1.1
ALC Port Number.
OBJECT-TYPE    
  INTEGER 1..54  

alcTContInterchangeAddress 1.3.6.1.4.1.449.2.1.4.10.3.1.2
ALC Interchange address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTContTerminalAddress 1.3.6.1.4.1.449.2.1.4.10.3.1.3
Address identifying this terminal.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

alcTContTerminalBoot 1.3.6.1.4.1.449.2.1.4.10.3.1.4
Boots the specified ALC terminal. boot - Boot the terminal. noBoot - Do not boot the terminal.
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcTContTerminalEnable 1.3.6.1.4.1.449.2.1.4.10.3.1.5
Enables the specified ALC Terminal. enable - Enable the terminal. noEnable - Do not enable the terminal.
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcTContTerminalDisable 1.3.6.1.4.1.449.2.1.4.10.3.1.6
Disables the specified ALC terminal. disable - Disable the terminal. noDisable - Do not disable the terminal.
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

Defined Objects

DisplayString  
OCTET STRING    

Cdx6500PPCTALCPortEntry  
SEQUENCE    
  INTEGER as alcPCfgPortNumber  
  INTEGER as alcPCfgPortType  
  INTEGER as alcPCfgSubtype  
  INTEGER as alcPCfgPortControl  
  INTEGER as alcPCfgClockSource  
  INTEGER as alcPCfgClockSpeed  
  INTEGER as alcPCfgPollDelayTimer  
  INTEGER as alcPCfgHostTimeout  
  INTEGER as alcPCfgMaxMesgSize  
  INTEGER as alcPCfgMinIntrvlBetweenPolls  
  INTEGER as alcPCfgRtsCtsTimeout  
  OCTET STRING as alcPCfgLeadPadChar  
  INTEGER as alcPCfgNumLeadPadChars  
  OCTET STRING as alcPCfgTrailPadChar  
  INTEGER as alcPCfgNumTrailPadChars  
  DisplayString as alcPCfgALCLineOptions  
  INTEGER as alcPCfgConnType  
  DisplayString as alcPCfgAcallMnemonic  
  DisplayString as alcPCfgCallingAddress  
  DisplayString as alcPCfgCUD  
  INTEGER as alcPCfgNumOfBuffers  
  DisplayString as alcPCfgInHeader  
  DisplayString as alcPCfgOutHeader  
  INTEGER as alcPCfgReconnectTimeout  
  INTEGER as alcPCfgInactivityTimeout  
  INTEGER as alcPCfgDebounceTimeout  
  INTEGER as alcPCfgParity  
  DisplayString as alcPCfgConnOptions  
  DisplayString as alcPCfgAvailableMesg  
  DisplayString as alcPCfgUnavailableMesg  

Cdx6500PPCTALCInterchangeEntry  
SEQUENCE    
  INTEGER as alcICfgPortNumber  
  OCTET STRING as alcICfgInterchangeAddress  
  INTEGER as alcICfgOptionOnInvalidCCC  
  OCTET STRING as alcICfgGenTerminalAddress  
  INTEGER as alcICfgHostTimeout  
  INTEGER as alcICfgMaxComponentsPerFrame  
  INTEGER as alcICfgFastPollCycleCount  
  INTEGER as alcICfgSlowPollCycleCount  
  INTEGER as alcICfgN1Counter  
  INTEGER as alcICfgN2Counter  
  INTEGER as alcICfgT1Timeout  
  INTEGER as alcICfgT2Timeout  
  DisplayString as alcICfgReenterMessage  
  DisplayString as alcICfgStartMessage  
  DisplayString as alcICfgStopMessage  
  DisplayString as alcICfgOptions  
  DisplayString as alcICfgValidTAList  
  INTEGER as alcICfgConnType  
  DisplayString as alcICfgAcallMnemonic  
  DisplayString as alcICfgCallingAddress  
  DisplayString as alcICfgCUD  
  INTEGER as alcICfgNumOfBuffers  
  DisplayString as alcICfgInHeader  
  DisplayString as alcICfgOutHeader  
  INTEGER as alcICfgReconnectTimeout  
  INTEGER as alcICfgInactivityTimeout  
  INTEGER as alcICfgDebounceTimeout  
  INTEGER as alcICfgParity  
  DisplayString as alcICfgConnOptions  
  DisplayString as alcICfgAvailableMesg  
  DisplayString as alcICfgUnavailableMesg  

Cdx6500PPCTALCTerminalEntry  
SEQUENCE    
  INTEGER as alcTCfgPortNumber  
  OCTET STRING as alcTCfgInterchangeAddress  
  OCTET STRING as alcTCfgTerminalAddress  
  INTEGER as alcTCfgConnType  
  DisplayString as alcTCfgAcallMnemonic  
  DisplayString as alcTCfgCallingAddress  
  DisplayString as alcTCfgCUD  
  INTEGER as alcTCfgNumOfBuffers  
  DisplayString as alcTCfgInHeader  
  DisplayString as alcTCfgOutHeader  
  INTEGER as alcTCfgReconnectTimeout  
  INTEGER as alcTCfgInactivityTimeout  
  INTEGER as alcTCfgDebounceTimeout  
  INTEGER as alcTCfgParity  
  DisplayString as alcTCfgConnOptions  
  DisplayString as alcTCfgAvailableMesg  
  DisplayString as alcTCfgUnavailableMesg  

Cdx6500PPSTALCPortEntry  
SEQUENCE    
  INTEGER as alcPStatsPortNumber  
  INTEGER as alcPStatsPortType  
  INTEGER as alcPStatsPortState  
  Counter as alcPStatsFramesIn  
  Counter as alcPStatsFramesOut  
  Counter as alcPStatsDataMesgsIn  
  Counter as alcPStatsDataMesgsOut  
  Counter as alcPStatsCharsIn  
  Counter as alcPStatsCharsOut  
  Counter as alcPStatsPolls  
  Counter as alcPStatsGAs  
  Counter as alcPStatsResets  
  Counter as alcPStatsDiscardBadIAIn  
  Counter as alcPStatsDiscardBadIAOut  
  INTEGER as alcPStatsMaxQSizeOut  
  Counter as alcPStatsCCCErrors  
  Counter as alcPStatsSignalLosses  
  Counter as alcPStatsOverlengthFrames  
  INTEGER as alcPStatsPortStatus  
  INTEGER as alcPStatsConnState  
  Counter as alcPStatsALCMesgsIn  
  Counter as alcPStatsALCMesgsOut  
  Counter as alcPStatsX25MesgsIn  
  Counter as alcPStatsX25MesgsOut  
  Counter as alcPStatsALCCharsIn  
  Counter as alcPStatsALCCharsOut  
  Counter as alcPStatsX25CharsIn  
  Counter as alcPStatsX25CharsOut  
  Counter as alcPStatsALCDiscardedMesgsEntityDown  
  Counter as alcPStatsX25DiscardedMesgsEntityDown  
  Counter as alcPStatsX25DiscardedMesgsBadALCAddr  
  Counter as alcPStatsX25DiscardedMesgsBadHeader  
  Counter as alcPStatsX25DiscardedMesgsTooLong  
  Counter as alcPStatsALCDiscardedMesgsQFull  
  Counter as alcPStatsX25DiscardedMesgsQFull  
  INTEGER as alcPStatsCurrTxALCQSize  
  INTEGER as alcPStatsCurrTxX25QSize  
  INTEGER as alcPStatsMaxTxALCQSize  
  INTEGER as alcPStatsMaxTxX25QSize  

Cdx6500PPSTALCInterchangeEntry  
SEQUENCE    
  INTEGER as alcIStatsPortNumber  
  OCTET STRING as alcIStatsInterchangeAddress  
  INTEGER as alcIStatsInterchangeState  
  Counter as alcIStatsFramesIn  
  Counter as alcIStatsFramesOut  
  Counter as alcIStatsDataMesgsIn  
  Counter as alcIStatsDataMesgsOut  
  Counter as alcIStatsCharsIn  
  Counter as alcIStatsCharsOut  
  Counter as alcIStatsPolls  
  Counter as alcIStatsGAs  
  Counter as alcIStatsResets  
  Counter as alcIStatsDiscardBadTAIn  
  Counter as alcIStatsDiscardBadTAOut  
  Counter as alcIStatsDisabledIAIn  
  Counter as alcIStatsDisabledIAOut  
  INTEGER as alcIStatsMaxQSizeOut  
  Counter as alcIStatsCCCErrors  
  Counter as alcIStatsT1Timeouts  
  Counter as alcIStatsT2Timeouts  
  INTEGER as alcIStatsConnState  
  Counter as alcIStatsALCMesgsIn  
  Counter as alcIStatsALCMesgsOut  
  Counter as alcIStatsX25MesgsIn  
  Counter as alcIStatsX25MesgsOut  
  Counter as alcIStatsALCCharsIn  
  Counter as alcIStatsALCCharsOut  
  Counter as alcIStatsX25CharsIn  
  Counter as alcIStatsX25CharsOut  
  Counter as alcIStatsALCDiscardedMesgsEntityDown  
  Counter as alcIStatsX25DiscardedMesgsEntityDown  
  Counter as alcIStatsX25DiscardedMesgsBadALCAddr  
  Counter as alcIStatsX25DiscardedMesgsBadHeader  
  Counter as alcIStatsX25DiscardedMesgsTooLong  
  Counter as alcIStatsALCDiscardedMesgsQFull  
  Counter as alcIStatsX25DiscardedMesgsQFull  
  INTEGER as alcIStatsCurrTxALCQSize  
  INTEGER as alcIStatsCurrTxX25QSize  
  INTEGER as alcIStatsMaxTxALCQSize  
  INTEGER as alcIStatsMaxTxX25QSize  

Cdx6500PPSTALCTerminalEntry  
SEQUENCE    
  INTEGER as alcTStatsPortNumber  
  OCTET STRING as alcTStatsInterchangeAddress  
  OCTET STRING as alcTStatsTerminalAddress  
  INTEGER as alcTStatsConnState  
  Counter as alcTStatsALCMesgsIn  
  Counter as alcTStatsALCMesgsOut  
  Counter as alcTStatsX25MesgsIn  
  Counter as alcTStatsX25MesgsOut  
  Counter as alcTStatsALCCharsIn  
  Counter as alcTStatsALCCharsOut  
  Counter as alcTStatsX25CharsIn  
  Counter as alcTStatsX25CharsOut  
  Counter as alcTStatsALCDiscardedMesgsEntityDown  
  Counter as alcTStatsX25DiscardedMesgsEntityDown  
  Counter as alcTStatsX25DiscardedMesgsBadALCAddr  
  Counter as alcTStatsX25DiscardedMesgsBadHeader  
  Counter as alcTStatsX25DiscardedMesgsTooLong  
  Counter as alcTStatsALCDiscardedMesgsQFull  
  Counter as alcTStatsX25DiscardedMesgsQFull  
  INTEGER as alcTStatsCurrTxALCQSize  
  INTEGER as alcTStatsCurrTxX25QSize  
  INTEGER as alcTStatsMaxTxALCQSize  
  INTEGER as alcTStatsMaxTxX25QSize  

Cdx6500ContALCPortEntry  
SEQUENCE    
  INTEGER as alcPContPortNumber  
  INTEGER as alcPContPortBoot  
  INTEGER as alcPContPortEnable  
  INTEGER as alcPContPortDisable  

Cdx6500ContALCInterchangeEntry  
SEQUENCE    
  INTEGER as alcIContPortNumber  
  OCTET STRING as alcIContInterchangeAddress  
  INTEGER as alcIContInterchangeBoot  
  INTEGER as alcIContInterchangeEnable  
  INTEGER as alcIContInterchangeDisable  

Cdx6500ContALCTerminalEntry  
SEQUENCE    
  INTEGER as alcTContPortNumber  
  OCTET STRING as alcTContInterchangeAddress  
  OCTET STRING as alcTContTerminalAddress  
  INTEGER as alcTContTerminalBoot  
  INTEGER as alcTContTerminalEnable  
  INTEGER as alcTContTerminalDisable