
| SNMPv2-SMI | SNMPv2-CONF | SNMPv2-TC |
| IF-MIB | INET-ADDRESS-MIB | ALCATEL-IND1-BASE |
| alcatelIND1BfdMIB | 1.3.6.1.4.1.6486.800.1.2.1.45.1 | ||
| This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line Configuration of Bidirectional Forwarding detection(BFD) protocol parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE | |||
| MODULE-IDENTITY | |||
| alaBfdObjects | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1 | ||
| Branch for Bi-Directional forwarding detection Subsystem managed objects | |||
| OBJECT-IDENTITY | |||
| alaBfdGlobalObjects | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| alaBfdGlobalAdminStatus | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.1 | ||
| The global administrative status of BFD in this router. | |||
| OBJECT-TYPE | |||
| AlaBfdStatus | |||
| alaBfdGlobalTxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.2 | ||
| The object specifies the Desired Tx interval at which BFD packets should be transmitted at global level. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdGlobalRxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.3 | ||
| The object specifies the Min Rx interval at which BFD packets should be transmitted at global level. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdGlobalOperMode | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.4 | ||
| The object specifies the operation mode at global level | |||
| OBJECT-TYPE | |||
| INTEGER | asyncMode(1), demandMode(2), echoOnly(3) | ||
| alaBfdGlobalVersionNumber | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.5 | ||
| The version number of the BFD protocol that this session is running in. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| alaBfdGlobalL2HoldTimer | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.6 | ||
| The object specifies the L2 convergence timer value at global level. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdGlobalProtocols | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.1.7 | ||
| BFD Protocol status: Bits 0 - 3 bit 0 - OSPF enabled/disabled bit 1 - BGP enabled/disabled bit 2 - DVMRP enabled/disabled bit 3 - VRRP enabled/disabled | |||
| OBJECT-TYPE | |||
| BITS | ospf(0), bgp(1), dvmrp(2), vrrp(3) | ||
| alaBfdGlobalEchoObjects | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| alaBfdGlobalEcho | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.2.1 | ||
| The object specifies status of echo mode at global level. | |||
| OBJECT-TYPE | |||
| AlaBfdStatus | |||
| alaBfdGlobalEchoRxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.2.2 | ||
| The object specifies the Echo Rx interval at which BFD packets should be transmitted at global level. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdIntfTable | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3 | ||
| The BFD Interface Table describes confiuration done over the BFD interfaces. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlaBfdIntfEntry | |||
| alaBfdIntfEntry | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1 | ||
| The BFD interface Entry describes BFD interface. | |||
| OBJECT-TYPE | |||
| AlaBfdIntfEntry | |||
| alaBfdIntfAddrType | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.1 | ||
| This object specifies IP address type values unknown(0), ipv4(1) or ipv6(2) have to be supported. | |||
| OBJECT-TYPE | |||
| InetAddressType | |||
| alaBfdIntfAddr | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.2 | ||
| The address of the BFD interface configured | |||
| OBJECT-TYPE | |||
| InetAddress | |||
| alaBfdIntfIndex | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.3 | ||
| The Interface Index of the BFD interface | |||
| OBJECT-TYPE | |||
| InterfaceIndex | |||
| alabfdIntfAdminStatus | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.4 | ||
| This object specifies the adminstatus of the BFD interface. | |||
| OBJECT-TYPE | |||
| AlaBfdStatus | |||
| alaBfdIntfDesiredMinTxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.5 | ||
| The object specifies the Desired Tx interval at which BFD packets should be transmitted at interface level. Default interval is global configured interval | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdIntfReqMinRxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.6 | ||
| The object specifies the Min Rx interval at which BFD packets should be transmitted at interface level.Default interval is global configured interval | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdIntfOperMode | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.7 | ||
| The object specifies the operation mode at interface level. Default mode is global mode | |||
| OBJECT-TYPE | |||
| INTEGER | asyncMode(1), demandMode(2), echoOnly(3) | ||
| alaBfdIntfEchoMode | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.8 | ||
| The object specifies status of echo mode at interface level. | |||
| OBJECT-TYPE | |||
| AlaBfdStatus | |||
| alaBfdIntfReqMinEchoRxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.9 | ||
| The object specifies the Echo Rx interval at which BFD packets should be transmitted at interface level. Default interval is global configured interval | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdIntfDetectMult | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.10 | ||
| The object specifies the Detect multiplier at interface level. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| alaBfdIntfsesstype | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.11 | ||
| The type of this BFD session corresponding to this interface. Currently single hop supported | |||
| OBJECT-TYPE | |||
| INTEGER | singleHop(1), multiHop(2) | ||
| alaBfdIntfAuthPresFlag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.12 | ||
| This object indicates that the local system's desire to use Authentication. Specifically, it is set to true(1) if the local system wishes the session to be authenticated or false(0) if not | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| alaBfdIntfAuthenticationType | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.13 | ||
| The Authentication Type used for this BFD session. This field is valid only when the Authentication Present bit is set | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), simplePassword(2), keyedMD5(3), meticulousKeyedMD5(4), keyedSHA1(5), meticulousKeyedSHA1(6) | ||
| alaBfdIntfL2HoldTimer | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.14 | ||
| The object configures layer 2 convergence timer | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdIntfRowStatus | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.3.1.15 | ||
| This variable is used to create, modify, and/or delete a row in this table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| alaBfdSessTable | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4 | ||
| The BFD Session Table describes the BFD sessions. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlaBfdSessEntry | |||
| alaBfdSessEntry | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1 | ||
| The BFD Session Entry describes BFD session. | |||
| OBJECT-TYPE | |||
| AlaBfdSessEntry | |||
| alaBfdSessDiscriminator | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.1 | ||
| This object specifies the local discriminator for this BFD session, used to uniquely identify it. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 1..4294967295 | ||
| alaBfdSessNeighborAddrType | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.2 | ||
| This object specifies IP address type values unknown(0), ipv4(1) or ipv6(2) have to be supported. | |||
| OBJECT-TYPE | |||
| InetAddressType | |||
| alaBfdSessNeighborAddr | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.3 | ||
| This object specifies the neighbor IpAddress. | |||
| OBJECT-TYPE | |||
| InetAddress | |||
| alaBfdSessRemoteDiscr | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.4 | ||
| This object specifies the local discriminator for this BFD session, used to uniquely identify it. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 1..4294967295 | ||
| alaBfdSessUdpPort | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.5 | ||
| The destination UDP Port for BFD. The default value is the well-known value for this port. | |||
| OBJECT-TYPE | |||
| InetPortNumber | |||
| alaBfdSessState | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.6 | ||
| The perceived state of the BFD session.BFD State failing(5) is only applicable if this BFD session is running version 0. | |||
| OBJECT-TYPE | |||
| INTEGER | adminDown(1), down(2), init(3), up(4), failing(5) | ||
| alaBfdSessRemoteHeardFlag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.7 | ||
| This object specifies status of BFD packet reception from the remote system. Specifically, it is set to true(1) if the local system is actively receiving BFD packets from the remote system, and is set to false(0) if the local system has not received BFD packets recently (within the detection time) or if the local system is attempting to tear down the BFD session. Value placed in this object is valid only if this session is running in BFD version 0. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| alaBfdSessDiag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.8 | ||
| A diagnostic code specifying the local system's reason for the last transition of the session from up(4)to some other state. | |||
| OBJECT-TYPE | |||
| AlaBfdDiag | |||
| alaBfdSessOperMode | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.9 | ||
| This object specifies current operating mode that BFD session is operating in. A value of AsyncMode(1) ... A value of DemandMode(2) ... | |||
| OBJECT-TYPE | |||
| INTEGER | asyncMode(1), demandMode(2), echoOnly(3) | ||
| alaBfdSessEchoFuncModeDesiredFlag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.10 | ||
| This object indicates that the local system's desire to use Echo mode. Specifically, it is set to true(1) if the local system wishes to use Echo mode or false(0) if not | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| alaBfdSessControlPlanIndepFlag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.11 | ||
| This object indicates that the local system's ability to continue to function through a disruption of the control plane. Specifically, it is set to true(1) if the local system BFD implementation independent of the control plane. Otherwise, the value is set to false(0) | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| alaBfdSessInterface | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.12 | ||
| This object contains an interface index used to indicate the interface which this BFD session is running on. This value can be zero if there are no interface associated with this BFD session | |||
| OBJECT-TYPE | |||
| InterfaceIndexOrZero | |||
| alaBfdSessNegotiatedTxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.13 | ||
| This object specifies the minimum interval, in milliseconds, that the local system will transmit BFD Control packets. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdSessNegotiatedRxInterval | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.14 | ||
| This object specifies the minimum interval, in milliseconds, that the local system will Receive BFD Control packets. | |||
| OBJECT-TYPE | |||
| AlaBfdInterval | |||
| alaBfdSessProtocols | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.4.1.15 | ||
| BFD Protocol status: Bits 0 - 3 bit 0 - OSPF enabled/disabled bit 1 - BGP enabled/disabled bit 2 - DVMRP enabled/disabled bit 3 - VRRP enabled/disabled bit 4 - IPRM enabled/disabled | |||
| OBJECT-TYPE | |||
| BITS | ospf(0), bgp(1), dvmrp(2), vrrp(3), iprm(4) | ||
| alaBfdSessPerfTable | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5 | ||
| This table specifies BFD Session performance counters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlaBfdSessPerfEntry | |||
| alaBfdSessPerfEntry | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1 | ||
| An entry in this table is created by a BFD-enabled node for every BFD Session. bfdCounterDiscontinuityTime is used to indicate potential discontinuity for all counter objects in this table. | |||
| OBJECT-TYPE | |||
| AlaBfdSessPerfEntry | |||
| alaBfdSessPerfPktIn | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.1 | ||
| The total number of BFD messages received for this BFD session. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alaBfdSessPerfPktOut | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.2 | ||
| The total number of BFD messages sent for this BFD session. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alaBfdSessPerfEchoOut | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.3 | ||
| The total number of BFD Echo messages sent for this BFD session. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alaBfdSessPerfUpTime | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.4 | ||
| The value of sysUpTime on the most recent occasion at which the session came up. If no such up event exists this object contains a zero value. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| alaBfdSessPerfLastSessDownTime | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.5 | ||
| The value of sysUpTime on the most recent occasion at which the last time communication was lost with the neighbor. If no such down event exist this object contains a zero value. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| alaBfdSessPerfLastCommLostDiag | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.6 | ||
| The BFD diag code for the last time communication was lost with the neighbor. If no such down event exists this object contains a zero value. | |||
| OBJECT-TYPE | |||
| AlaBfdDiag | |||
| alaBfdSessPerfSessUpCount | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.7 | ||
| The number of times this session has gone into the Up state since the router last rebooted. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alaBfdSessPerfDiscTime | 1.3.6.1.4.1.6486.800.1.2.1.45.1.1.5.1.8 | ||
| The value of sysUpTime on the most recent occasion at which any one or more of the session counters suffered a discontinuity.The relevant counters are the specific instances associated with this BFD session of any Counter64 object contained in the BfdSessPerfTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| alcatelIND1BfdMIBConformance | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2 | ||
| Conformance | |||
| OBJECT-IDENTITY | |||
| alcatelIND1BfdMIBGroups | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| alaBfdbasicGroup | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.1.1 | ||
| A collection of objects providing information about the configuration done for BFD at global level. | |||
| OBJECT-GROUP | |||
| alaBfdIntfCfgGroup | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.1.2 | ||
| A collection of objects providing information about the configuration done for a BFD interface. | |||
| OBJECT-GROUP | |||
| alaBfdSessGroup | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.1.3 | ||
| A collection of objects providing information about the BFD session. | |||
| OBJECT-GROUP | |||
| alaBfdSessPerfGroup | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.1.4 | ||
| A collection of objects providing information about the BFD session performance counters. | |||
| OBJECT-GROUP | |||
| alcatelIND1BfdMIBCompliances | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| alcatelIND1BfdMIBCompliance | 1.3.6.1.4.1.6486.800.1.2.1.45.1.2.2.1 | ||
| The compliance statement for device support of BFD. | |||
| MODULE-COMPLIANCE | |||
| AlaBfdInterval | |||
| The BFD interval delay in milliseconds. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1..65535 | ||
| AlaBfdDiag | |||
| A common BFD diagnostic code. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | noDiagnostic(1), controlDetectionTimeExpired(2), echoFunctionFailed(3), neighborSignaledSessionDown(4), forwardingPlaneReset(5), pathDown(6), concatenatedPathDown(7), administrativelyDown(8), reverseConcatenatedPathDown(9) | ||
| AlaBfdStatus | |||
| Admin status | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | enabled(1), disabled(2) | ||
| AlaBfdIntfEntry | |||
| SEQUENCE | |||
| InetAddressType as alaBfdIntfAddrType | |||
| InetAddress as alaBfdIntfAddr | |||
| InterfaceIndex as alaBfdIntfIndex | |||
| AlaBfdStatus as alabfdIntfAdminStatus | |||
| AlaBfdInterval as alaBfdIntfDesiredMinTxInterval | |||
| AlaBfdInterval as alaBfdIntfReqMinRxInterval | |||
| AlaBfdStatus as alaBfdIntfEchoMode | |||
| AlaBfdInterval as alaBfdIntfReqMinEchoRxInterval | |||
| Unsigned32 as alaBfdIntfDetectMult | |||
| INTEGER as alaBfdIntfOperMode | |||
| INTEGER as alaBfdIntfsesstype | |||
| TruthValue as alaBfdIntfAuthPresFlag | |||
| INTEGER as alaBfdIntfAuthenticationType | |||
| AlaBfdInterval as alaBfdIntfL2HoldTimer | |||
| RowStatus as alaBfdIntfRowStatus | |||
| AlaBfdSessEntry | |||
| SEQUENCE | |||
| Unsigned32 as alaBfdSessDiscriminator | |||
| InetAddressType as alaBfdSessNeighborAddrType | |||
| InetAddress as alaBfdSessNeighborAddr | |||
| Unsigned32 as alaBfdSessRemoteDiscr | |||
| InetPortNumber as alaBfdSessUdpPort | |||
| INTEGER as alaBfdSessState | |||
| TruthValue as alaBfdSessRemoteHeardFlag | |||
| AlaBfdDiag as alaBfdSessDiag | |||
| INTEGER as alaBfdSessOperMode | |||
| TruthValue as alaBfdSessEchoFuncModeDesiredFlag | |||
| TruthValue as alaBfdSessControlPlanIndepFlag | |||
| InterfaceIndexOrZero as alaBfdSessInterface | |||
| AlaBfdInterval as alaBfdSessNegotiatedTxInterval | |||
| AlaBfdInterval as alaBfdSessNegotiatedRxInterval | |||
| BITS as alaBfdSessProtocols | |||
| AlaBfdSessPerfEntry | |||
| SEQUENCE | |||
| Counter64 as alaBfdSessPerfPktIn | |||
| Counter64 as alaBfdSessPerfPktOut | |||
| Counter64 as alaBfdSessPerfEchoOut | |||
| TimeTicks as alaBfdSessPerfUpTime | |||
| TimeTicks as alaBfdSessPerfLastSessDownTime | |||
| AlaBfdDiag as alaBfdSessPerfLastCommLostDiag | |||
| Counter64 as alaBfdSessPerfSessUpCount | |||
| TimeTicks as alaBfdSessPerfDiscTime | |||